Sva150xg04tb Nec
Sva150xg04tb Nec
Sva150xg04tb Nec
SN-SA-A0003-02-E 1/36
XGA
DATA SHEET
(Version 2.0 )
Published by
Technology Department
SVA - NEC Liquid Crystal Display Co., Ltd.
L Approved by Date
Checked by Date
Prepared by Date
Signature of customer
Confirmed by Date
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 2/36
INTRODUCTION
• WARRANTY
Shanghai SVA NEC Liquid Crystal Display Co., Ltd. (hereinafter called "SVA-NEC") warrants that this product
meets the product specifications set forth in this document. If this product under normal operation is found to be
non-conforming to the product specifications, and such non-conformance is promptly notified to SVA-NEC within
one (1) year after the delivery date, and further such non-conformance is solely attributable to SVA-NEC, SVA-NEC
shall repair the non-conforming product or replace it with a conforming one, free of charge. However, this warranty
does not apply to any non-conformance that can be found easily by incoming inspections or those resulting from any
one of the following:
1) Unauthorized or improper repair, maintenance or modification
2) Operation or use against specifications, instructions or warnings given by SVA-NEC
3) Any other causes attributable to customer
In case SVA-NEC repairs or replaces a product after the one (l)-year warranty period, SVA-NEC shall be entitled to
charge for such repair or replacement. Those replaced parts shall be covered with six (6)-month warranty period from
the replacement day. Non-conforming products may be replaced with substitutes instead of repair when the manufacture
of this product has been terminated.
EXCEPT AS EXPRESSLY SET FORTH HEREIN, SVA-NEC DISCLAIMS ANY WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE, AND DISCLAIMS ANY REMEDIES.
• MAINTENANCE
The specifications of maintenance parts may be partially changed within equivalent quality or better. In this
product, SVA-NEC will not accept to maintain for only mounting parts on circuit board (e.g. connector, fuse, capacitor,
resistor, etc.) and only backlight conformation parts (e.g. reflector sheet, light guide plate, etc.).
If SVA-NEC is planning discontinuation for this product, SVA-NEC shall inform it to customers in six (6)-months
advance from the issued date of official agreements. In addition, after product discontinuation, SVA-NEC may replace
substitutes instead of maintenance parts with whole product.
• CHANGE CONTROL
For the purpose of product improvement, this product design may be changed for specifications, appearance, parts,
circuits and so on. In case a design change is affected on the product specifications, SVA-NEC shall inform it to
customers in advance.
Any question arising out of, or in connection with, this SPECIFICATION or any matter not stipulated herein will be
settled each time upon consultation between both parties.
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 3/36
CONTENTS
INTRODUCTION .................................................................................................................................................... 2
CONTENTS ............................................................................................................................................................. 3
1. OUTLINE ............................................................................................................................................................. 4
1.1 STRUCTURE AND PRINCIPLE................................................................................................................ 4
1.2 APPLICATIONS ......................................................................................................................................... 4
1.3 FEATURES................................................................................................................................................. 4
2. GENERAL SPECIFICATIONS ............................................................................................................................ 5
3. BLOCK DIAGRAM ............................................................................................................................................. 6
4. DETAILED SPECIFICATION.............................................................................................................................. 7
4.1 MECHANICAL SPECIFICATIONS........................................................................................................... 7
4.2 ABSOLUTE MAXIMUM RATINGS ......................................................................................................... 7
4.3 ELECTRICAL CHARACTERISTICS ........................................................................................................ 8
4.4 POWER SUPPLY VOLTAGE SEQUENCE................................................................................................ 9
4.5 CONNECTIONS AND FUNCTIONS FOR INTERFACE PINS............................................................... 10
4.6 DISPLAY COLORS AND INPUT DATA SIGNALS ................................................................................ 14
4.7 DISPLAY POSITIONS ............................................................................................................................. 15
4.8 INPUT SIGNAL TIMINGS FOR LCD PANEL SIGNAL PROCESSING BOARD.................................. 15
4.9 OPTICS..................................................................................................................................................... 18
4.10 DEFECT CRITERIA............................................................................................................................... 20
5. RELIABILITY TESTS ....................................................................................................................................... 24
6. ESTIMATED LUMINANCE LIFETIME ........................................................................................................... 25
7. MARKINGS ....................................................................................................................................................... 26
7.1 NAMEPLATE LABEL ............................................................................................................................. 26
7.2 BARCODE LABEL.................................................................................................................................. 26
7.3 OTHER MARKINGS ............................................................................................................................... 26
7.4 INDICATION LOCATIONS ..................................................................................................................... 27
8. PACKING, TRANSPORTATION AND DELIVERY .......................................................................................... 28
8.1 PACKING ................................................................................................................................................. 28
8.2 INSPECTION RECORD SHEET.............................................................................................................. 28
8.3 TRANSPORTATION ................................................................................................................................ 28
8.4 SIZE AND WEIGHT FOR PACKING BOX............................................................................................. 28
8.5 OUTLINE FIGURE FOR PACKING........................................................................................................ 29
9. PRECAUTIONS ................................................................................................................................................. 31
9.1 MEANING OF CUTION SIGNS.............................................................................................................. 31
9.2 CAUTIONS ............................................................................................................................................ 31
9.3 ATTENTIONS .......................................................................................................................................... 31
10.OUTDRAWING ................................................................................................................................................ 35
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 4/36
1. OUTLINE
SVA150XG04TB module is composed of the amorphous silicon thin film transistor liquid crystal display (a-Si
TFT LCD) panel structure with driver LSIs for driving the TFT (Thin Film Transistor) array and a backlight.
The a-Si TFT LCD panel structure is injected liquid crystal material into a narrow gap between the TFT array
glass substrate and a color-filter glass substrate.
Color (Red, Green, Blue) data signals from a host system (e.g. PC, signal generator, etc.) are modulated into best
form for active matrix system by a signal processing board, and sent to the driver LSIs which drive the individual
TFT arrays.
The TFT array as an electro-optical switch regulates the amount of transmitted light from the backlight assembly,
when it is controlled by data signals. Color images are created by regulating the amount of transmitted light through
the TFT array of red, green and blue dots.
1.2 APPLICATIONS
• Monitor for PC
1.3 FEATURES
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 5/36
2. GENERAL SPECIFICATIONS
Designed viewing direction • Viewing angle with optimum grayscale (γ=2.2): normal axis
At LCD panel center
Color gamut
60 % (typ.) [against NTSC color space]
Ton (white 90% black 10%) + Toff (black 10% whjte 90%)
Response time
16 ms (typ.)
At IBL = 7.5mArms / lamp
Luminance
250cd/m2(typ.)
LVDS 1port
Signal system
[ RGB :8-bit, Dot clock (CLK), Data enable (DE)]
Power supply voltage LCD panel signal processing board:3.3V
Edge light type:2 cold cathode fluorescent lamps
Backlight Replaceable part
• Lamp holder set:Type No. 150LHS21
At IBL=7.5mArms / lamp and checkered flag pattern
Power consumption
9.5W (typ.)
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 6/36
3. BLOCK DIAGRAM
D0- 100Ω
D1- 100Ω
D1+
D2- 100Ω
Source Driver
D2+
100Ω
CLK- 3072 columns
CLK+
LVDS)
Gate Driver
100Ω
D3- LCD Panel
D3+ 768 rows
MSL H:1024×3(R,G,B)
FUSE V:768
VCC
DC/DC
Power
converter
VBLH1/2
Edge side backlight
VBLC2/2
Note1: Connections between GND, FG (Frame ground) and VBLC (Lamp low voltage terminal) in the product
GND - FG Connected
GND - VBLC Not connected
FG - VBLC Not connected
Note2: These grounds should be connected together in customer equipment.
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 7/36
4. DETAILED SPECIFICATION
Module size 326.5± 0.5 (W) x 253.5 ± 0.5 (H) x 11.2 ± 0.5 (D) Note1 mm
Display area 304.128 (W) x 228.096 (H) Note1 mm
Weight 1000 (typ.) g
Note1: See “10. OUTLINE DRAWINGS”.
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 8/36
Pa
Sa |Pa - Pb| / Pb × 100 ≤ 5%
|Sa - Sb| / Sb × 100 ≤ 5%
Sb
Pb
Pa: Supply voltage/current peak for positive, Pb: Supply voltage/current peak for negative
Sa: Waveform space for positive part, Sb: Waveform space for negative part
Note3: Recommended value of “FO” is as following.
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 9/36
3.0 V
VCC 2.5 V 3.0 V
0V
Note1 A D B C
This product works, even if the ripple voltage levels are beyond the permissible values as the following table,
but there might be noise on the display image.
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 10/36
4.4.3 Fuse
Fuse
Parameter Rating Fusing current Remarks
Type Supplier
2.5 A
VCC TF16SN2.50 KOA Corporation 5.0 A Note1
32 V
Note1: The power supply capacity should be more than the fusing current. If the power supply capacity is less than the
fusing current, the fuse may not blow for a short time, and then nasty smell, smoking and so on may occur.
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 11/36
4.5.2 Backlight lamp
Attention: VBLH and VBLC must be connected correctly. IF customer connects wrongly, customer will be
hurt and the product will be broken.
1
CN201
3
Signal processing board
Low voltage CN1
(Cold)
20 1
Insert direction
Low voltage(Cold)
3
CN202
1
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 12/36
4.5.4 Connection between receiver and transmitter for LVDS
(1) Input LVDS map A (MSL :”High”)
Host LCD Module(Product)
R2 TA0
R3 TA1
R4 TA2
R5 TA3
R6 TA4 TA- D0-
R7 TA5 TA+ D0+
G2 TA6
TB- D1-
G3 TB0
TB+ D1+
G4 TB1
G5 TB2
G6 TB3 TC- D2-
G7 TB4 TC+ D2+
B2 TB5
B3 TB6 TCLK- CLK-
TCLK+ CLK+
B4 TC0
B5 TC1 TD- D3-
B6 TC2 TD+ D3+
B7 TC3
High or Low TC4
High or Low TC5
DE TC6
“High” MSL
R0 TD0
R1 TD1
G0 TD2
G1 TD3
B0 TD4
B1 TD5
RSVD TD6
DCLK CLK IN
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 13/36
R0 TXIN0
R1 TXIN1
R2 TXIN2
R3 TXIN3
R4 TXIN4 D0-
R5 TXIN6 D0+
G0 TXIN7
D1-
G1 TXIN8
TXIN9 D1+
G2
G3 TXIN12
G4 TXIN13 D2-
G5 TXIN14 D2+
B0 TXIN15
B1 TXIN18 CLK-
CLK+
B2 TXIN19
B3 TXIN20 D3-
B4 TXIN21 D3+
B5 TXIN22
High or Low TXIN24
High or Low TXIN25
DE TXIN26
“Low” MSL
R6 TXIN27 or “Open”
R7 TXIN5
G6 TXIN10
G7 TXIN11
B6 TXIN16
B7 TXIN18
RSVD TXIN23
CLK CLK IN
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 14/36
This product can display in equivalent to 16,777,216 colors in 256 scale. Also the relation between display colors
and input data signals is as the following table.
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Blue 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Red 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Basic Color
Magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Green 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
Cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Dark
Red grayscale
0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
: : :
: : :
Bright 1 1 1 1 1 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Red
1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0
Green grayscale
Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0
: : :
: : :
Bright
0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 1 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0
Green
0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
Blue grayscale
Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
: : :
: : :
Bright 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 1
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0
Blue
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 15/36
The following table is the coordinates per pixel(See ”4.8 SCANNING DIRECTIONS”.).
C(1,1)
R G B
4.8 INPUT SIGNAL TIMINGS FOR LCD PANEL SIGNAL PROCESSING BOARD
DE (Data enable)
Display period
Note1
·Vertical signal
Vertical display period (tvd)
DE (Data enable)
1 2 3 4 768
Display period
Note1
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 16/36
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 17/36
4.8.3 Input signal timing chart
tv
Tvd=768H
DE
DE
Thd=1024CLK
th
tc
DATA
Invalid Invalid
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 18/36
4.9 OPTICS
50cm
Photodetector (TOPCON BM-5A)
LCD module 1º
(Product)
Note 2:See“4.10.2 Definition of contrast ratio”.
Note 3:See“4.10.3 Definition of luminance uniformity”.
Note 4:Product surface temperature:TopF=28.0℃
Note 5:See “4.10.4 Definition of response times”.
Note 6:See “4.10.5 Definition of viewing angles”.
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 19/36
4.9.2 Definition of contrast ratio
The contrast ratio is calculated by using the following formula.
Contrast ratio(CR)= Luminance of white screen
Luminance of black screen
126 ① ②
384 ③
640 ④ ⑤
Luminance
Black
10%
0%
Ton Toff
4.9.5 Definition of viewing angles
Normal axis (Perpendicular)
12 o’clock
Left θL
Upper
θU
θD θR
Lower
Right
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 20/36
4.10 DEFECT CRITERIA
Temperature 25±5℃
Inspection viewing distance 20cm(The distance between the inspector’s eye and screen)
0°≤θR≤20°,0°≤θL≤20°
Inspection direction
0°≤θU≤20°
Inspection illumination 60lx(at a display surface)
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 21/36
: Bright dot
Defect pattern : Dark dot Criteria
15mm≤ D Allowed
Bright dots
15mm≤ D Allowed
Dark dots
15mm≤ D
Combinations between bright
Allowed
dot and dark dot
: Bright dot
Defect pattern Criteria
: Dark dot
≤1set
≤1 set
2defect dots
≤2 sets
Etc.
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 22/36
: Bright dot
Defect pattern : Dark dot Criteria
Bright dot
0 set
Dark dot
3 defect dots
Allowed
Etc.
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 23/36
Temperature 25±5℃
Inspection viewing distance 20cm (The distance between the inspector’s eye and screen.)
0°≤θR≤45°, 0°≤θL≤45°
Inspection direction
0°≤θU≤45°, 0°≤θD≤45°
Illumination 700lx (at an inspection desk surface)
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 24/36
5. RELIABILITY TESTS
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 25/36
Luminance
Condition lifetime(MTTF) Unit
Note1,Note2
25℃(Ambient temperature of the
product)
40,000 h
Continuous operation and
IBL=7.5mArms/lamp
Module
50℃(Surface temperature at screen
center)
35,000 h
Continuous operation and
IBL=7.5mArms/lamp
25℃(Ambient temperature of the
Cold cathode
product)
Fluorescent 50,000 h
Continuous operation and
lamp
IBL=7.5mArms/lamp
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 26/36
7. MARKINGS
The various markings are attached to this product. See “8.4 INDECATION LOCATIONS” for attachment positions.
RO
Company emblem
REV:A MADE IN CHINA Country of manufacture
1111 A 1 04 9 01 001
Internal Revision Internal Manufacturing year Manufacturing Manufacturing Production
use 1 letter use 2 figures of the A.D. month day number
(Alphabet) end numbers 1 letter Multi-letter
(e.g: A.D2004 is 04.) (figure)
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 27/36
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 28/36
SVA-NEC will pack products to deliver to customer in accordance with SVA-NEC packing specifications, and will
deliver products to customer in such a state that products will not suffer from a damage during transportation .The
delivery conditions are as follows.
8.1 PACKING
Inspection record sheets are included in the packing box with delivery products to customer. It is summarized to a
number of products for pass/fail assessment.
8.3 TRANSPORTATION
The product is transported by vehicle, aircraft or shipment in the state of pallet packing.
Weight 1.6(typ.) kg
11.3(typ.)
Total weight kg
(with 10 products)
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 29/36
LCD module
Antistatic pouch
SVA
SVA
LCD module
Inspection record
sheet
Packing box
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 30/36
(2)Pallet packing
Note: The ways for Packing and Shipping vary from different shipment volume, dependent on specific situations.
Cardboard pallet
Cardboard sleeve
Top cap
Band
Cardboard sleeve
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 31/36
9. PRECAUTIONS
The following caution signs have very important meaning .Be sure to read “10.2 CAUTIONS” and “10.3
ATTENTIONS”, after understanding these contents!
This sign have the meaning that customer will be injured by himself or the product will
sustain a damage, if customer has wrong operations.
This sign has the meaning that customer will get an electrical shock, if customer has
wrong operations.
This sign has the meaning that customer will be injured by himself, if customer has
wrong operations.
9.2 CAUTIONS
* Do not touch lamp cables while turn on .Customers will be in danger of an electric shock
* Do not touch the working backlight and IC. Customers will be in danger of burn injury.
* Do not shock and press the LCD panel and the backlight! There is a danger of breaking,
because they are made of glass.(shock :To be not greater 294m/s2 and to be not greater
11ms, Pressure: To be not greater 19.6N)
9.3 ATTENTIONS
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 32/36
un-uniformity.
⑦Do not press or rub on the sensitive display surface .If customer clean on the panel surface, SVA-NEC recommends
using the cloth with ethanolic liquid such as screen cleaner for LCD.
⑧ Do not push-pull the interface connectors while the product is working, because wrong power sequence may break
down the product.
⑨ Do not bend or unbend the lamp cable at the near part of the lamp holding rubber, to avoid the damage for high
voltage side of the lamp. This damage may cause a lamp breaking and abnormal operation of high voltage circuit.
9.3.2 Environment
① Do not operate or store in high temperature, high humidity, dewdrop atmosphere or corrosive gases. Keep the
product in antistatic pouch in room temperature, because of avoidance for dusts and sunlight, if customer stores
the product.
② In order to prevent dew condensation occurring by temperature difference, the product packing box must be
opened after leave under the environment of an unpacking room temperature enough. Because a situation of dew
condensation occurring is changed by the environment temperature and humidity, evaluate the leaving time
sufficiently. (Recommendation leaving time: 6 hour or more with packing state)
③ Do not operate in a high magnetic field .Circuit boards may be broken down by it.
④ This product is not designed as radiation hardened.
⑤ Use an original protection sheet on the product surface (polarizer). Adhesive type protection sheet should be
avoided, because it may change color or properties of the polarizer.
9.3.3 Characteristics
The following items are neither defects nor failures.
① Response time, luminance and color may be changed by ambient temperature.
②The LCD may be seemed luminance non-uniformity, flicker, vertical seam or small spot by display patterns.
③Optical characteristics (e.g. luminance, display uniformity, etc.) gradually is going to change depending on
operating time ,and especially low temperature, because the LCD has cold cathode fluorescent lamps.
④Do not display the fixed pattern for a long time because it may cause image sticking .Use a screen saver, if the
fixed pattern is displayed on the screen.
⑤The display color may be changed by viewing angle because of the use of condenser sheet in the backlight.
⑥Optical characteristics may be changed by input signal timings.
⑦The interference noise of input signal frequency for this product and luminance control frequency of customer’s
backlight inverter may appear on a display. Set up luminance control frequency of backlight inverter so that the
interference noise doses not appear.
9.3.4 Other
①All GND and VCC terminals should be used without a non-connected line.
②Do not disassemble a product or adjust volume without permission of SVA-NEC.
③See “REPLACEMENT MANUAL FOR LAMPHOLDER SET”, if customer would like to replace backlight
lamps.
④Pay attention not to insert waste materials inside of products, if customer uses screw nails.
⑤Pack the product with original shipping package, because of avoidance of some damages during transportation,
when customer returns it to SVA-NEC for repair and so on .
⑥Not only the module but also the equipment should be packed and transported as the module. becomes
vertical .Otherwise, there is the fear that a display dignity decreases by an impact or vibrations.
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 33/36
10.OUTDRAWING
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 34/36
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 35/36
1 2005-5- Rev1.0
20 Contrast has been changed, TBD
is be added by the value.
KINO OKABE ZHOU
SHITA SHI
HUAN
S
i
g
n
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.
SN-SA-A0003-02-E 36/36
2 2005-6- Rev2.0
20 The distance of screw in front
view outdrawing was changed
from 225mm TO 224mm. ZHOU
The new passage“ 4.10 DEFECT SHI
CRITERIA”was added in. HUAN
The Name plate label was Yang
renewed wi th added REV of label Gang
and ROHS mark.
2005-6
-20
S
i
g
n
Not duplication without authorization Shanghai SVA NEC Liquid Crystal Display Co., Ltd.