Turcon® Glyd Ring®

Double Acting
Rubber Energized Plastic Faced
Seal
Material:
Turcon®, Zurcon® and Elastomer

Latest information available at www.tss.trelleborg.com

Edition January 2011
15
 Turcon® Glyd Ring®

Latest information available at www.tss.trelleborg.com

16 Edition January 2011
 Turcon® Glyd Ring®

„ Turcon® Glyd Ring® Notches are standard on the following series and
diameters
Description PG 42 for bore dia. > 30 mm
PG 44 for bore dia. > 20 mm
Successfully used for decades, the Tucon® Glyd PG 46 for bore dia. > 40 mm
Ring® is a very effective and reliable low frictional
seal. It is particularly suitable as a piston seal in
both high and low pressure systems. Advantages

The double acting Tucon® Glyd Ring® is a combination of - No stick-slip effect when starting for smooth operation
a Turcon based slipper seal and an energising O-Ring. It is - Minimum static and dynamic friction coefficient for a
produced with an interference fit which together with the minimum energy loss and operating temperature
squeeze of the O-Ring ensures a good sealing effect even
at low pressure. At higher system pressures, the O-Ring is - Suitable for non lubricating fluids depending on seal
energised by the fluid, pushing the Turcon® Glyd Ring® material for optimum design flexibility
against the sealing face with increased force.
- High wear resistance ensures long service life
- Installation grooves acc. to ISO 7425/1
- No adhesive effect to the mating surface during long
period of inactivity or storage
- Suitable for most hydraulic fluids in relation with
most modern hardware materials and surface finish
depending on material selected.
- Suitable for new environmentally safe hydraulic fluids
- Available for all cylinder diameters up to 2.700 mm.

Application Examples

Figure 12 Turcon® Glyd Ring® Over several decades the Turcon® Glyd Ring® has been
successfully implemented in a large variety of applications
The geometry of the Tucon® Glyd Ring® ensures a good as double acting Piston seals of hydraulic components such
static sealing and allows the lubricating hydrodynamic oil as:
film to be build under the seal in reciprocating applications. - Injection moulding machines
Notches - Machine tools
To assure that a rapid energising of the seal takes place
at sudden changes of pressure and direction of motion, - Presses
radial "notches" are machined on both sides of the seal. - Excavators
- Forklifts & handling machinery

Notches - Agriculture equipment

- Valves for hydraulic & pneumatic circuits

p - Servo equipment
- Pressure intensifiers
- Jacks

Figure 13 Turcon® Glyd Ring® with notches

Latest information available at www.tss.trelleborg.com

Edition January 2011
17
 Turcon® Glyd Ring®

Technical Data Materials

Operating conditions: The following material combinations have proven effective
® ®
The Turcon Glyd Ring is recommended for reciprocating for hydraulic applications:
(with a length of stroke at least twice the groove width) For light to heavy applications with reciprocating
and helical movements. movements in mineral oils and other media with good
Pressure: Up to 60 MPa lubrication:
All round material for hydraulic applications with
Speed: Up to 15 m/s reciprocating, short stroke or helical movements in mineral
oils, flame retardant hydraulic fluids HFC, phosphate
Frequency: Up to 5 Hz. ester, bio-oils or fluids having less satisfactory lubricating
properties:
Temperature: -45 °C to +200 °C *)
(depending on O-Ring Material) Turcon® Glyd Ring®: Turcon® M12

Media: Mineral oil based hydraulic fluids, O-Ring: NBR, 70 Shore A N

flame retardant hydraulic fluids, FKM, 70 Shore A V
environmentally safe hydraulic fluids
(bio-oils), phosphate ester, water and Set code: M12N or M12V
others, depending on the seal and
O-Ring material compatibility (see For medium to heavy applications with reciprocating
Table X) movements in mineral oils and other media with good
lubrication:
Clearance: The maximum permissible radial Turcon® Glyd Ring®: Turcon® T46
clearance Smax is shown in the Table
XI as a function of the operating
pressure and functional diameter. O-Ring: NBR, 70 Shore A N
FKM, 70 Shore A V
Important Note: Set code: T46N or T46V
The above data are maximum values and cannot be
used at the same time. e.g. the maximum operating
speed depends on material type, pressure, For specific applications, all Turcon® materials are available.
temperature and gap value. Temperature range Other viable material combinations are listed in Table IX.
also dependent on medium.

*) In the case of unpressurized applications in

temperatures below 0°C please contact our
application engineers for assistance!

Latest information available at www.tss.trelleborg.com

18 Edition January 2011
 Turcon® Glyd Ring®

Table IX Turcon® and Zurcon® Materials for Glyd Ring®

Material, Code O-Ring Material Code O-Ring Mating Surface MPa
Applications, Shore A Operating Temp.* Material max.
Properties °C Dyna-
mic
Turcon® M12 M12 NBR - 70 N -30 to +100 Steel 50
First material choice for seals in linear NBR - 70 T -45 to +80 Steel hardened
motion Low temp Steel chrome
Overall improved properties plated (rod)
For new constructions and updating FKM - 70 V -10 to +200 Steel plated (rod)
For all commonly applied hydraulic fluids Cast iron
including fluids with low lubrication Stainless steel
performance Titanium
Lowest friction and best sliding properties
Lowest wear on seals
Improved absorption of abrasive contaminants
No wear or abrasion of counter surface
Mineral fibre and Additives filled
Colour: Dark grey
Turcon® T05 T05 NBR - 70 N -30 to +100 Steel hardened 20
For lubricating fluids NBR - 70 T -45 to +80 Steel chrome
Also for gas service Low temp. plated (rod)
Very low friction
Very good sliding and sealing properties FKM - 70 V -10 to +200
Colour: Turquoise
Turcon® T08 T08 NBR - 70 N -30 to +100 Steel hardened 60
For lubricating fluids and linear motion NBR - 70 T -45 to +80 Steel chrome
Very high compressive strength and Low temp. plated (rod)
extrusion resistance Cast iron
Hard counter surfaces is recommended FKM - 70 V -10 to +200
Bronze filled
Colour: Light to dark brown,
which may have variations in shading
Turcon® T10 T10 NBR - 70 N -30 to +100 Steel 40
For hydraulic and pneumatic NBR - 70 T -45 to +80 Steel hardened
For lubricating and non-lubricating fluids Low temp. Steel chrome
High extrusion resistance plated (rod)
Good chemical resistance FKM - 70 V -10 to +200 Stainless steel
Not for electrically conducting fluids EPDM-70 E** -45 to +145
BAM tested
Carbon, graphite filled
Colour: Black
Turcon® T29 T29 NBR - 70 N -30 to +100 Steel 30
For lubricating and non-lubricating fluids NBR - 70 T -45 to +80 Steel hardened
Good extrusion resistance Low temp. Steel chrome
Surface texture is not suitable for gas sealing plated (rod)
Not for electrically conducting fluids FKM - 70 V -10 to +200 Cast iron
Carbon fibre filled EPDM- 70 E** -45 to +145 Stainless steel
Colour: Grey

Turcon® T40 T40 NBR - 70 N -30 to +100 Steel 25

For lubricating and non-lubricating fluids NBR - 70 T -45 to +80 Steel hardened
High frequency and short strokes Low temp. Steel chrome
Water hydraulics plated (rod)
Surface texture is not suitable for gas sealing FKM - 70 V -10 to +200 Cast iron
Carbon fibre filled EPDM- 70 E** -45 to +145 Stainless steel
Colour: Grey Aluminium
* The O-Ring Operation Temperature is only valid in mineral hydraulic oil (except EPDM). ** Material not suitable for mineral oils.
*** max. Ø 2300 mm BAM: Tested by "Bundesanstalt Materialprüfung, Germany". Highlighted materials are standard.

Latest information available at www.tss.trelleborg.com

Edition January 2011
19
 Turcon® Glyd Ring®

Material, Code O-Ring Material Code O-Ring Mating Surface MPa

Applications, Shore A Operating Temp.* Material max.
Properties °C Dyna-
mic
Turcon® T46 T46 NBR - 70 N -30 to +100 Steel hardened 50
For lubricated hydraulics in linear motion NBR - 70 T -45 to +80 Steel chrome
High compressive strength Low temp. plated (rod)
High extrusion resistance Cast iron
Very good sliding and wear properties FKM - 70 V -10 to +200
BAM tested
Bronze filled
Colour: Light to dark brown,
which may have variations in shading
Zurcon® Z51*** Z51 NBR - 70 N -30 to +100 Steel 60
For mineral oil based fluids NBR - 70 T -45 to +80 Steel hardened
Very high abrasion and extrusion Low temp. Steel chrome
resistance plated (rod)
For counter surface with rougher surface Cast iron
finish Stainless steel
Limited chemical resistance Ceramic coating
Max. working temperature 110 °C
Cast polyurethane
Colour: Yellow to light-brown
Zurcon® Z80 Z80 NBR - 70 N -30 to (+100) Steel 35
For lubricating and non-lubricating fluids NBR - 70 T -45 to +80 Steel hardened
Water based fluids, air and gases Low temp. Steel chrome
Dry air pneumatics plated (rod)
High abrasion and extrusion resistance EPDM- 70 E** -45 to (+145) Stainless steel
For service in abrasive conditions and media Aluminium
with particles Ceramic coating
Good chemical resistance
Limited temperature capability (-60 to +80 °C)
UHMWPE (Ultra High Molecular Weight
Polyethylene)
Colour: White to off-white
* The O-Ring Operation Temperature is only valid in mineral hydraulic oil (except EPDM). ** Material not suitable for mineral oils.
*** max. Ø 2300 mm BAM: Tested by "Bundesanstalt Materialprüfung, Germany". Highlighted materials are standard.

Latest information available at www.tss.trelleborg.com

20 Edition January 2011
 Turcon® Glyd Ring®

„ Installation Recommendation

R max. 0.3

S
d2

r1
DN

d1

L1

Figure 14 Installation drawing

Table X Installation dimensions

Bore Diameter DN H9 Groove Groove Radius Radial Clearance S max.* O-Ring
Diameter Width Cross-
Series No. PG 44 Series No. PG 46 Series No. PG 42
Section

Standard Light Application Heavy Duty d1 h9 L1 +0.2 r1 10 MPa 20 MPa 40 MPa d2

Application Application
8 - 14.9 15 - 39.9 - DN - 4.9 2.2 0.4 0.30 0.20 0.15 1.78
15 - 39.9 40 - 79.9 - DN - 7.5 3.2 0.6 0.40 0.25 0.15 2.62
40 - 79.9 80 - 132.9 15 - 39.9 DN - 11.0 4.2 1.0 0.40 0.25 0.20 3.53
80 - 132.9 133 - 329.9 40 - 79.9 DN - 15.5 6.3 1.3 0.50 0.30 0.20 5.33
133 - 329.9 330 - 669.9 80 - 132.9 DN - 21.0 8.1 1.8 0.60 0.35 0.25 7.00
330 - 669.9 670 - 999.9 133 - 329.9 DN - 24.5 8.1 1.8 0.60 0.35 0.25 7.00
670 - 999.9 ⱖ 1000 330 - 669.9 DN - 28.0 9.5 2.5 0.70 0.50 0.30 8.40
ⱖ 1000 ⱖ 1000 ⱖ 1000 DN - 38.0 13.8 3.0 1.00 0.70 0.60 12.00

* At pressures > 40 MPa use diameter tolerance H8/f8 (bore/piston) in area of the seal or consult TSS for alternative material or profiles.
TSS Slydring® / Wear Rings are not applicable at very small radical clearance S. Please consult the Slydring® catalog.
O-Rings with 12 mm cross section are delivered as special profilring.

Latest information available at www.tss.trelleborg.com

Edition January 2011
21
 Turcon® Glyd Ring®

Ordering Example
TSS Article No. PG44 0 0800 - M12 N
Turcon® Glyd Ring®, complete with O-Ring, standard
application, Series PG44 (from Table X). TSS Series No.
Bore diameter: DN = 80.0 mm Type (Standard)
TSS Part No.: PG4400800 (from Table XI)
Bore diameter x 10*
Select the material from Table IX. The corresponding code
Quality Index (Standard)
numbers are appended to the TSS Part No. Preferred Series
(Table XI). Material code (Seal ring)
Together they form the TSS Article Number. The TSS Article
Number for all intermediate sizes not shown in Preferred Material code (O-Ring)
Series (Table XI) can be determined following the example
opposite. * For diameters DN t 1000.0 mm multiply only by factor 1.
Example: PG44 for diameter DN 1200.0 mm.
TSS Article No.: PG44X1200 - M12N.
Table XI Installation dimensions / TSS Part No.
Bore Groove Groove TSS Part No. O-Ring Bore Groove Groove TSS Part No. O-Ring
Dia. Dia. Width Dimensions Dia. Dia. Width Dimensions
DN H9 d1 h9 L1 +0.2 DN H9 d1 h9 L1 +0.2
8.0 3.1 2.2 PG4400080 2.90 x 1.78 36.0 28.5 3.2 PG4400360 28.24 x 2.62
10.0 5.1 2.2 PG4400100 4.80 x 1.8 38.0 30.5 3.2 PG4400380 29.82 x 2.62
12.0 7.1 2.2 PG4400120 6.70 x 1.8 40.0 32.5 3.2 PG4600400 31.42 x 2.62
14.0 9.1 2.2 PG4400140 8.75 x 1.8 40.0 29.0 4.2 PG4400400 28.17 x 3.53
15.0 7.5 3.2 PG4400150 7.59 x 2.62 42.0 31.0 4.2 PG4400420 29.75 x 3.53
16.0 11.1 2.2 PG4600160 10.82 x 1.78 44.45 36.95 3.2 PG4600444 36.17 x 2.62
16.0 8.5 3.2 PG4400160 7.59 x 2.62 45.0 34.0 4.2 PG4400450 32.92 x 3.53
18.0 13.1 2.2 PG4600180 12.42 x 1.78 48.0 37.0 4.2 PG4400480 36.09 x 3.53
18.0 10.5 3.2 PG4400180 9.19 x 2.62 50.0 42.5 3.2 PG4600500 40.94 x 2.62
19.05 11.55 3.2 PG4400190 10.77 x 2.62 50.0 39.0 4.2 PG4400500 37.70 x 3.53
20.0 15.1 2.2 PG4600200 14.00 x 1.78 50.0 34.5 6.3 PG4200500 32.69 x 5.33
20.0 12.5 3.2 PG4400200 12.37 x 2.62 50.8 43.3 3.2 PG4600508 42.52 x 2.62
21.0 13.5 3.2 PG4400210 12.37 x 2.62 50.8 39.8 4.2 PG4400508 37.70 x 3.53
22.0 17.1 2.2 PG4600220 17.17 x 1.78 52.0 41.0 4.2 PG4400520 40.87 x 3.53
22.0 14.5 3.2 PG4400220 13.94 x 2.62 53.0 42.0 4.2 PG4400530 40.87 x 3.53
24.0 16.5 3.2 PG4400240 15.54 x 2.62 55.0 44.0 4.2 PG4400550 44.04 x 3.53
25.0 20.1 2.2 PG4600250 18.77 x 1.78 57.0 46.0 4.2 PG4400570 44.04 x 3.53
25.0 17.5 3.2 PG4400250 17.12 x 2.62 58.0 47.0 4.2 PG4400580 47.22 x 3.53
25.0 14.0 4.2 PG4200250 13.87 x 3.53 60.0 49.0 4.2 PG4400600 47.22 x 3.53
25.4 20.5 2.2 PG4600254 17.12 x 2.62 62.0 51.0 4.2 PG4400620 50.39 x 3.53
28.0 20.5 3.2 PG4400280 20.29 x 2.62 63.0 52.0 4.2 PG4400630 50.39 x 3.53
30.0 22.5 3.2 PG4400300 21.89 x 2.62 63.0 47.5 6.3 PG4200630 46.99 x 5.33
32.0 27.1 2.2 PG4600320 26.70 x 1.78 65.0 54.0 4.2 PG4400650 53.57 x 3.53
32.0 24.5 3.2 PG4400320 23.47 x 2.62 68.0 57.0 4.2 PG4400680 56.74 x 3.53
32.0 21.0 4.2 PG4200320 20.22 x 3.53 70.0 59.0 4.2 PG4400700 56.74 x 3.53
35.0 27.5 3.2 PG4400350 26.64 x 2.62 70.0 54.5 6.3 PG4200700 53.34 x 5.33
35.0 24.0 4.2 PG4200350 23.40 x 3.53 75.0 64.0 4.2 PG4400750 63.09 x 3.53

Latest information available at www.tss.trelleborg.com

22 Edition January 2011
 Turcon® Glyd Ring®

Bore Groove Groove TSS Part No. O-Ring Bore Groove Groove TSS Part No. O-Ring
Dia. Dia. Width Dimensions Dia. Dia. Width Dimensions
DN H9 d1 h9 L1 +0.2 DN H9 d1 h9 L1 +0.2
75.0 59.5 6.3 PG4200750 56.52 x 5.33 150.0 134.5 6.3 PG4601500 132.72 x 5.33
80.0 69.0 4.2 PG4600800 66.27 x 3.53 150.0 129.0 8.1 PG4401500 126.37 x 7.0
80.0 64.5 6.3 PG4400800 62.87 x 5.33 155.0 134.0 8.1 PG4401550 132.72 x 7.0
80.0 59.0 8.1 PG4200800 58 x 7.0 160.0 144.5 6.3 PG4601600 142.24 x 5.33
82.5 67.0 6.3 PG4400825 66.04 x 5.33 160.0 139.0 8.1 PG4401600 135.89 x 7.0
85.0 69.5 6.3 PG4400850 69.22 x 5.33 165.0 144.0 8.1 PG4401650 142.24 x 7.0
85.0 64.0 8.1 PG4200850 63 x 7.0 170.0 149.0 8.1 PG4401700 145.42 x 7.0
90.0 79.0 4.2 PG4600900 78.97 x 3.53 175.0 154.0 8.1 PG4401750 151.77 x 7.0
90.0 74.5 6.3 PG4400900 72.39 x 5.33 180.0 164.5 6.3 PG4601800 164.47 x 5.33
90.0 69.0 8.1 PG4200900 68 x 7.0 180.0 159.0 8.1 PG4401800 158.12 x 7.0
95.0 84.0 4.2 PG4600950 82.14 x 3.53 190.0 169.0 8.1 PG4401900 164.47 x 7.0
95.0 79.5 6.3 PG4400950 78.74 x 5.33 194.0 178.5 6.3 PG4601940 177.17 x 5.33
95.0 74.0 8.1 PG4200950 73 x 7.0 200.0 184.5 6.3 PG4602000 183.52 x 5.33
100.0 89.0 4.2 PG4601000 88.49 x 3.53 200.0 179.0 8.1 PG4402000 177.17 x 7.0
100.0 84.5 6.3 PG4401000 81.92 x 5.33 205.0 184.0 8.1 PG4402050 183.52 x 7.0
100.0 79.0 8.1 PG4201000 78 x 7.0 210.0 189.0 8.1 PG4402100 183.52 x 7.0
101.6 86.1 6.3 PG4401016 85.09 x 5.33 215.0 194.0 8.1 PG4402150 189.87 x 7.0
105.0 94.0 4.2 PG4601050 91.67 x 3.53 220.0 199.0 8.1 PG4402200 196.22 x 7.0
105.0 89.5 6.3 PG4401050 88.27 x 5.33 230.0 214.5 6.3 PG4602300 208.92 x 5.33
108.0 92.5 6.3 PG4401080 91.44 x 5.33 230.0 209.0 8.1 PG4402300 208.90 x 7.0
110.0 99.0 4.2 PG4601100 98.02 x 3.53 240.0 219.0 8.1 PG4402400 215.27 x 7.0
110.0 94.5 6.3 PG4401100 91.44 x 5.33 250.0 229.0 8.1 PG4402500 227.97 x 7.0
110.0 89.0 8.1 PG4201100 88 x 7.0 250.0 225.5 8.1 PG4202500 215.27 x 7.0
115.0 99.5 6.3 PG4401150 97.79 x 5.33 250.0 234.5 6.3 PG4602500 234.32 x 5.33
120.0 109.0 4.2 PG4601200 107.54 x 3.53 254.0 233.0 8.1 PG4402540 227.97 x 7.0
120.0 104.5 6.3 PG4401200 100.97 x 5.33 260.0 239.0 8.1 PG4402600 240.67 x 7.0
120.0 99.0 8.1 PG4201200 98 x 7.0 265.0 244.0 8.1 PG4402650 240.67 x 7.0
125.0 114.0 4.2 PG4601250 113.89 x 3.53 268.0 247.0 8.1 PG4402680 240.67 x 7.0
125.0 109.5 6.3 PG4401250 107.32 x 5.33 270.0 249.0 8.1 PG4402700 240.67 x 7.0
125.0 104.0 8.1 PG4201250 103 x 7.0 280.0 259.0 8.1 PG4402800 253.37 x 7.0
127.0 111.5 6.3 PG4401270 110.49 x 5.33 290.0 269.0 8.1 PG4402900 266.07 x 7.0
130.0 114.5 6.3 PG4401300 113.67 x 5.33 300.0 279.0 8.1 PG4403000 278.77 x 7.0
130.0 109.0 8.1 PG4201300 108 x 7.0 300.0 275.5 8.1 PG4203000 266.07 x 7.0
132.0 121.0 4.2 PG4601320 120.24 x 3.53 304.8 283.8 8.1 PG4403048 278.77 x 7.0
135.0 114.0 8.1 PG4401350 113.67 x 7.0 310.0 289.0 8.1 PG4403100 278.77 x 7.0
140.0 124.5 6.3 PG4601400 123.19 x 5.33 320.0 299.0 8.1 PG4403200 291.47 x 7.0
140.0 119.0 8.1 PG4401400 116.84 x 7.0 320.0 295.5 8.1 PG4203200 291.47 x 7.0
145.0 129.5 6.3 PG4601450 126.37 x 5.33 330.0 305.5 8.1 PG4403300 304.17 x 7.0
145.0 124.0 8.1 PG4401450 123.19 x 7.0 340.0 315.5 8.1 PG4403400 316.87 x 7.0

Latest information available at www.tss.trelleborg.com

Edition January 2011
23
 Turcon® Glyd Ring®

Bore Groove Groove TSS Part No. O-Ring

Dia. Dia. Width Dimensions
DN H9 d1 h9 L1 +0.2
350.0 325.5 8.1 PG4403500 316.87 x 7.0
360.0 335.5 8.1 PG4403600 329.57 x 7.0
370.0 345.5 8.1 PG4403700 342.27 x 7.0
380.0 355.5 8.1 PG4403800 354.97 x 7.0
400.0 375.5 8.1 PG4404000 367.67 x 7.0
420.0 395.5 8.1 PG4404200 393.07 x 7.0
430.0 405.5 8.1 PG4404300 405.26 x 7.0
440.0 415.5 8.1 PG4404400 405.26 x 7.0
450.0 425.5 8.1 PG4404500 417.96 x 7.0
460.0 435.5 8.1 PG4404600 430.66 x 7.0
480.0 455.5 8.1 PG4404800 456.06 x 7.0
500.0 475.5 8.1 PG4405000 468.76 x 7.0
555.0 530.5 8.1 PG4405550 506.86 x 7.0
600.0 575.5 8.1 PG4406000 557.66 x 7.0
640.0 615.5 8.1 PG4406400 608.08 x 7.0
660.0 635.5 8.1 PG4406600 633.48 x 7.0
700.0 672.0 9.5 PG4407000 670 x 8.4
710.0 682.0 9.5 PG4407100 680 x 8.4
740.0 712.0 9.5 PG4407400 710 x 8.4
780.0 752.0 9.5 PG4407800 750 x 8.4
800.0 772.0 9.5 PG4408000 770 x 8.4
900.0 872.0 9.5 PG4409000 870 x 8.4
1000.0 972.0 9.5 PG46X1000 970 x 8.4
1000.0 962.0 13.8 PG44X1000 960 x 12.0
1050.0 1022.0 9.5 PG46X1050 1020 x 8.4
1065.0 1027.0 13.8 PG44X1065 1025 x 12.0
1070.0 1032.0 13.8 PG44X1070 1030 x 12.0
1200.0 1172.0 9.5 PG46X1200 1170 x 8.4
1200.0 1162.0 13.8 PG44X1200 1160 x 12.0
1225.0 1187.0 13.8 PG44X1225 1185 x 12.0
1500.0 1462.0 13.8 PG44X1500 1460 x 12.0
2000.0 1962.0 13.8 PG44X2000 1960 x 12.0
2700.0 2662.0 13.8 PG44X2700 2660 x 12.0

All dimensions in bold type are suitable for installation in

grooves to ISO 7425/1, bore dia. in accordance with ISO 3320.
Other dimensions and all intermediate sizes up to 2700 mm dia.
including inch sizes can be supplied.
All O-Rings with 12 mm cross section are delivered as special
Profilring.

Latest information available at www.tss.trelleborg.com

24 Edition January 2011
Turcon® Glyd Ring® T

Double Acting
Rubber Energized Plastic Faced
Seal
Material:
Turcon®, Zurcon® and Elastomer

Latest information available at www.tss.trelleborg.com

Edition January 2011
25
 Latest information available at www.tss.trelleborg.com
26 Edition January 2011
 Turcon® Glyd Ring® T

„ Turcon® Glyd Ring® T* - Simple groove design, one-piece pistons possible

- Installation grooves to ISO 7425/1
Description
- Adaptable to the operating conditions due to a wide
Turcon® Glyd Ring® T is a further technical range of possible materials (Turcon®, Zurcon®)
development of the Turcon® Glyd Ring® seal
which has been successfully used for decades. - Suitable for new environmentally safe hydraulic fluids
It is fully interchangeable with the earlier Glyd - Available for all cylinder diameters up to 2.700 mm.
Ring® seals in all new applications. Glyd Ring® T meets all
the market demands for a function-specific seal solution,
observing economic and ecological aspects. Application Examples

The benefits of the patented seal concept are provided The Turcon® Glyd Ring® T is the recommended sealing
by the innovative functional principle of the trapezoidal element for double acting pistons of hydraulic components
profile cross-section. such as:
Both lateral profile flanks are inclined so that the seal - Injection moulding machines
profile tapers towards the seal surface. The profile can thus
- Machine tools
retain the robust and compact form typical of piston seals
without losing any of the flexibility required to achieve a - Presses
pressure-related maximum compression (Figure 15).
- Excavators
- Forklifts & handling machinery

p - Agriculture

Turcon® Seal ring - Valves for hydraulic & pneumatic circuits.

- Servo equipment
O-Ring
- Pressure intensifiers
- Jacks
It is particularly recommended for heavy duty and large
diameter applications.

Figure 15 Turcon® Glyd Ring® T

Single acting hydraulic cylinder
Test conditions: HLP 46, 80°C, Pressure cycle 0/30MPa,
®
The edge angle created by the special Glyd Ring T piston moving in pressure direction
crosssectional form permits an additional degree of
freedom and enables a slight tilting movement of the seal. Turcon® Glyd Ring®
The maximum compression is thus always shifted towards PG4400600-T46
the area of the seal edge directly exposed to the pressure. Turcon® Glyd Ring® T
Accumulated leakage

On the low-pressure edge of the seal, on the other hand, PT0300600-T46

the Glyd Ring® T exhibits only zones with neutral strains
without compressive or shearing loads, thus effectively
reducing the danger of gap extrusion. The resulting
benefits for the user can be seen in the following list.

Advantages
Cycles
The benefits offered to date by the Glyd Ring® are still
retained in full, and are now complemented by a number Figure 16 Dynamic leakage Turcon® Glyd Ring® T/
of further important advantages: Turcon® Glyd Ring® as single acting piston
- Very good static leak-tightness seal

- Increased clearance possible (approx. +50%), depending

* Patent No.:
on the operating conditions DE 4140833C3
- Due to the larger extrusion gap, safe use even with EP 0582593
Japan 2799367
soiled media
USA 5,433,452
- Low friction, no stick-slip effect

Latest information available at www.tss.trelleborg.com

Edition January 2011
27
 Turcon® Glyd Ring® T

Technical Data For specific applications, other viable material combinations

are listed in Table XIII.
Operating conditions
Pressure: Up to 60 MPa
Series
Speed: Up to 15 m/s
Different cross-section sizes are recommended as a
function of the seal diameters.
Temperature: -45 °C to +200 °C *)
(depending on O-Ring material). Table XII, shows the relationship between the series
number according to the seal diameter range and the
Media: Mineral oil-based hydraulic fluids, different application class sizes. These application classes
flame retardant hydraulic fluids, are:
environmentally safe hydraulic
Standard application: General applications in
fluids (bio-oils), phosphate ester,
which no exceptional
water, air and others, depending
operating conditions exist.
on the seal and O-Ring material
compatibility (see Table XIII)
Light application: Applications with demands
for reduced friction or for
Clearance: The maximum permissible radial
smaller grooves.
clearance smax is shown in Table XIV,
as a function of the operating
Heavy-duty application: For exceptional operating
pressure and functional diameter.
loads such as high
pressures, pressure peaks,
Important Note: etc.
The above data are maximum values and cannot be
used at the same time. e.g. the maximum operating Table XII Available range
speed depends on material type, pressure,
temperature and gap value. Temperature range Series No. Piston Diameter
also dependent on medium. DN H9
PT00 8.0 - 140.0
*) In the case of unpressurized applications in PT01 8.0 - 200.0
temperatures below 0°C please contact our
application engineers for assistance! PT02 16.0 - 380.0
PT03 40.0 - 480.0
Materials PT04 80.0 - 700.0
PT08 133.0 - 999.9
The following material combinations have proven effective
for hydraulic applications: PT05 310.0 - 999.9
PT05X 1000.0 - 1200.0
All round material for hydraulic applications with
PT06 750.0 - 999.9
reciprocating or short stroke in mineral oils, flame
retardant hydarulic fluids HFC, phosphate ester, bio-oils or PT06X 1000.0 - 2700.0
fluids having less satisfactory properties.
For the recommended range see Table XIV.
Turcon® Glyd Ring® T: Turcon® M12

O-Ring: NBR, 70 Shore A N

FKM, 70 Shore A V

Set code: M12N or M12V

For medium to heavy applications with reciprocating

movements in mineral oils and other media with good
lubrication:
Turcon® Glyd Ring® T: Turcon® T46

O-Ring: NBR, 70 Shore A N

FKM, 70 Shore A V

Set code: T46N or T46V

Latest information available at www.tss.trelleborg.com

28 Edition January 2011
 Turcon® Glyd Ring® T

Table XIII Turcon® and Zurcon® Materials for Glyd Ring® T

Material, Code O-Ring Material Code O-Ring Mating Surface MPa
Applications, Shore A Operating Temp.* Material max.
Properties °C Dyna-
mic
Turcon® M12 M12 NBR - 70 N -30 to +100 Steel 50
First material choice for seals in linear Steel hardened
NBR - 70 T -45 to +80
motion Steel chrome
Low temp.
Overall improved properties plated (rod)
For new constructions and updating FKM - 70 V -10 to +200 Steel plated (rod)
For all commonly applied hydraulic fluids Cast iron
including fluids with low lubrication Stainless steel
performance Titanium
Lowest friction and best sliding properties
Lowest wear on seals
Improved absorption of abrasive
contaminants
No wear or abrasion of counter surface
Mineral fibre and Additives filled
Colour: Dark grey
Turcon® T40 T40 NBR - 70 N -30 to +100 Steel 25
For lubricating and non-lubricating fluids NBR - 70 T -45 to +80 Steel hardened
High frequency and short strokes Low temp. Steel chrome
Water hydraulics plated (rod)
Surface texture is not suitable for gas sealing FKM - 70 V -10 to +200 Cast iron
Carbon fibre filled EPDM - 70 E** -45 to +145 Stainless steel
Colour: Grey Aluminium
Turcon® T46 T46 NBR - 70 N -30 to +100 Steel hardened 50
For lubricated hydraulics in linear motion NBR - 70 T -45 to +80 Steel chrome
High compressive strength Low temp.70 plated (rod)
High extrusion resistance Cast iron
Very good sliding and wear properties FKM - 70 V -10 to +200
BAM tested
Bronze filled
Colour: Light to dark brown,
which may have variations in shading
Zurcon® Z51*** Z51 NBR - 70 N -30 to +100 Steel 60
For mineral oil based fluids NBR - 70 T -45 to +80 Steel hardened
Very high abrasion and extrusion Low temp. Steel chrome
resistance plated (rod)
For counter surface with rougher surface Cast iron
finish Stainless steel
Limited chemical resistance Ceramic coating
Max. working temperature 110 °C
Cast polyurethane
Colour: Yellow to light-brown
Zurcon® Z80 Z80 NBR - 70 N -30 to (+100) Steel 35
For lubricating and non-lubricating fluids NBR - 70 T -45 to +80 Steel hardened
Water based fluids, air and gases Low temp. Steel chrome
Dry air pneumatics plated (rod)
High abrasion and extrusion resistance EPDM- 70 E** -45 to(+145) Stainless steel
For service in abrasive conditions and media Aluminium
with particles Ceramic coating
Good chemical resistance
Limited temperature capability (-60 to
+80 °C)
UHMWPE (Ultra High Molecular Weight
Polyethylene)
Colour: White to off-white
* The O-Ring Operation Temperature is only valid in mineral hydraulic oil (except EPDM). ** Material not suitable for mineral oils.
*** max. Ø 2300 mm BAM: Tested by "Bundesanstalt Materialprüfung, Germany". Highlighted materials are standard.

Latest information available at www.tss.trelleborg.com

Edition January 2011
29
 Turcon® Glyd Ring® T

„ Installation Recommendation
R max. 0.3

S
d2

r1
DN

d1

L1

Figure 17 Installation drawing

Table XIV Installation Dimensions – Standard recommendations

Series- Bore Diameter Groove Groove Radius Radial Clearance S max.* O-Ring
No. DN H9 Diameter Width Cross-
Sec.
Standard Light Heavy Duty d1 h9 L1 +0.2 r1 10 MPa 20 MPa 40 MPa d2
Application Application Application
PT00 8 - 14.9 15 - 39.9 -- DN - 4.9 2.2 0.4 0.40 0.30 0.20 1.78
PT01 15 - 39.9 40 - 79.9 -- DN - 7.5 3.2 0.6 0.60 0.50 0.30 2.62
PT02 40 - 79.9 80 - 132.9 15 - 39.9 DN - 11.0 4.2 1.0 0.70 0.50 0.30 3.53
PT03 80 - 132.9 133 - 329.9 40 - 79.9 DN - 15.5 6.3 1.3 0.80 0.60 0.40 5.33
PT04 133 - 329.9 330 - 669.9 80 - 132.9 DN - 21.0 8.1 1.8 0.80 0.60 0.40 7.00
PT08 330 - 669.9 670 - 999.9 133 - 329.9 DN - 24.5 8.1 1.8 0.90 0.70 0.50 7.00
PT05 670 - 999.9 -- 310 - 669.9 DN - 28.0 9.5 2.5 1.00 0.80 0.60 8.40
PT05X -- 1000 - 1200 -- DN - 28.0 9.5 2.5 1.00 0.80 0.60 8.40
PT06** -- -- 670 - 999.9 DN - 38.0 13.8 3.0 1.20 0.90 0.70 12.00
PT06X** 1000 - 2700 -- -- DN - 38.0 13.8 3.0 1.20 0.90 0.70 12.00

* At pressures > 40 MPa use diameter tolerance H8/f8 (bore/piston) in area of the seal or consult TSS for alternative material or profiles.
TSS Slydring® / Wear Rings are not applicable at very small radical clearance S. Please consult the Slydring® catalog.
** O-Rings with 12 mm cross section are delivered as special profilring.

Latest information available at www.tss.trelleborg.com

30 Edition January 2011
 Turcon® Glyd Ring® T

Ordering example
TSS Article No. PT03 0 0800 - M12 N
Turcon® Glyd Ring® T, complete with O-Ring, standard
application, series PT03 (from Table XIV). TSS Series No.
Bore diameter: DN = 80.0 mm
TSS Part No.: PT0300800 (from Table XV) Type (Standard)

Select the material from Table XIII. The corresponding Cylinder diameter x 10***
code numbers are appended to the TSS Part No. (from Quality Index (Standard)
Table XV). Together they form the TSS Article No.
For all intermediate sizes not shown in Table XV, the TSS Material code (Seal ring)
Article No. can be determined from the example opposite. Material code (O-Ring)

*** For diameters t 1000.0 mm multiply only by factor 1.

Example: PT06 for diameter 1200.0 mm.
TSS Article No.: PT06X1200 - M12N.
Table XV Installation dimensions / TSS Part No.
Bore Groove Groove TSS Part O-Ring Bore Groove Groove TSS Part O-Ring
Dia. Dia. Width No. Dimensions Dia. Dia. Width No. Dimensions
DN H9 d1 h9 L1 +0.2 DN H9 d1 h9 L1 +0.2
8.0 3.1 2.2 PT0000080 2.90 x 1.78 32.0 21.0 4.2 PT0200320 20.22 x 3.53
10.0 5.1 2.2 PT0000100 4.80 x 1.8 35.0 27.5 3.2 PT0100350 26.64 x 2.62
12.0 7.1 2.2 PT0000120 6.70 x 1.8 35.0 24.0 4.2 PT0200350 23.40 x 3.53
14.0 9.1 2.2 PT0000140 8.75 x 1.8 36.0 28.5 3.2 PT0100360 28.24 x 2.62
15.0 7.5 3.2 PT0100150 7.59 x 2.62 38.0 30.5 3.2 PT0100380 29.82 x 2.62
16.0 11.1 2.2 PT0000160 10.82 x 1.78 40.0 32.5 3.2 PT0100400 31.42 x 2.62
16.0 8.5 3.2 PT0100160 7.59 x 2.62 40.0 29.0 4.2 PT0200400 28.17 x 3.53
18.0 13.1 2.2 PT0000180 12.42 x 1.78 42.0 31.0 4.2 PT0200420 29.75 x 3.53
18.0 10.5 3.2 PT0100180 9.19 x 2.62 44.45 36.95 3.2 PT0100444 36.17 x 2.62
19.05 11.55 3.2 PT0100190 10.77 x 2.62 45.0 34.0 4.2 PT0200450 32.92 x 3.53
20.0 15.1 2.2 PT0000200 14.00 x 1.78 48.0 37.0 4.2 PT0200480 36.09 x 3.53
20.0 12.5 3.2 PT0100200 12.37 x 2.62 50.0 42.5 3.2 PT0100500 40.94 x 2.62
21.0 13.5 3.2 PT0100210 12.37 x 2.62 50.0 39.0 4.2 PT0200500 37.70 x 3.53
22.0 17.1 2.2 PT0000220 17.17 x 1.78 50.0 34.5 6.3 PT0300500 32.69 x 5.33
22.0 14.5 3.2 PT0100220 13.94 x 2.62 50.8 43.3 3.2 PT0100508 42.52 x 2.62
24.0 16.5 3.2 PT0100240 15.54 x 2.62 50.8 39.8 4.2 PT0200508 37.70 x 3.53
25.0 20.1 2.2 PT0000250 18.77 x 1.78 52.0 41.0 4.2 PT0200520 40.87 x 3.53
25.0 17.5 3.2 PT0100250 17.12 x 2.62 53.0 42.0 4.2 PT0200530 40.87 x 3.53
25.0 14.0 4.2 PT0200250 13.87 x 3.53 55.0 44.0 4.2 PT0200550 44.04 x 3.53
25.4 20.5 2.2 PT0000254 17.12 x 2.62 57.0 46.0 4.2 PT0200570 44.04 x 3.53
28.0 20.5 3.2 PT0100280 20.29 x 2.62 58.0 47.0 4.2 PT0200580 47.22 x 3.53
30.0 22.5 3.2 PT0100300 21.89 x 2.62 60.0 49.0 4.2 PT0200600 47.22 x 3.53
32.0 27.1 2.2 PT0000320 26.70 x 1.78 62.0 51.0 4.2 PT0200620 50.39 x 3.53
32.0 24.5 3.2 PT0100320 23.47 x 2.62 63.0 52.0 4.2 PT0200630 50.39 x 3.53

Latest information available at www.tss.trelleborg.com

Edition January 2011
31
 Turcon® Glyd Ring® T

Bore Groove Groove TSS Part O-Ring Bore Groove Groove TSS Part O-Ring
Dia. Dia. Width No. Dimensions Dia. Dia. Width No. Dimensions
DN H9 d1 h9 L1 +0.2 DN H9 d1 h9 L1 +0.2
63.0 47.5 6.3 PT0300630 46.99 x 5.33 127.0 111.5 6.3 PT0301270 110.49 x 5.33
65.0 54.0 4.2 PT0200650 53.57 x 3.53 130.0 114.5 6.3 PT0301300 113.67 x 5.33
68.0 57.0 4.2 PT0200680 56.74 x 3.53 130.0 109.0 8.1 PT0401300 108 x 7.0
70.0 59.0 4.2 PT0200700 56.74 x 3.53 132.0 121.0 4.2 PT0201320 120.24 x 3.53
70.0 54.5 6.3 PT0300700 53.34 x 5.33 135.0 114.0 8.1 PT0401350 113.67 x 7.0
75.0 64.0 4.2 PT0200750 63.09 x 3.53 140.0 124.5 6.3 PT0301400 123.19 x 5.33
75.0 59.5 6.3 PT0300750 56.52 x 3.53 140.0 119.0 8.1 PT0401400 116.84 x 7.0
80.0 69.0 4.2 PT0200800 66.27 x 3.53 145.0 129.5 6.3 PT0301450 126.37 x 5.33
80.0 64.5 6.3 PT0300800 62.87 x 5.33 145.0 124.0 8.1 PT0401450 123.19 x 7.0
80.0 59.0 8.1 PT0400800 58 x 7.0 150.0 134.5 6.3 PT0301500 132.72 x 5.33
82.5 67.0 6.3 PT0300825 66.04 x 5.33 150.0 129.0 8.1 PT0401500 126.37 x 7.0
85.0 69.5 6.3 PT0300850 69.22 x 5.33 155.0 134.0 8.1 PT0401550 132.72 x 7.0
85.0 64.0 8.1 PT0400850 63 x 7.0 160.0 144.5 6.3 PT0301600 142.24 x 5.33
90.0 79.0 4.2 PT0200900 78.97 x 3.53 160.0 139.0 8.1 PT0401600 135.89 x 7.0
90.0 74.5 6.3 PT0300900 72.39 x 5.33 165.0 144.0 8.1 PT0401650 142.24 x 7.0
90.0 69.0 8.1 PT0400900 68 x 7.0 170.0 149.0 8.1 PT0401700 145.42 x 7.0
95.0 84.0 4.2 PT0200950 82.14 x 3.53 175.0 154.0 8.1 PT0401750 151.77 x 7.0
95.0 79.5 6.3 PT0300950 78.74 x 5.33 180.0 164.5 6.3 PT0301800 164.47 x 5.33
95.0 74.0 8.1 PT0400950 73 x 7.0 180.0 159.0 8.1 PT0401800 158.12 x 7.0
100.0 89.0 4.2 PT0201000 88.49 x 3.53 190.0 169.0 8.1 PT0401900 164.47 x 7.0
100.0 84.5 6.3 PT0301000 81.92 x 5.33 194.0 178.5 6.3 PT0301940 177.17 x 5.33
100.0 79.0 8.1 PT0401000 78 x 7.0 200.0 184.5 6.3 PT0302000 183.52 x 5.33
101.6 86.1 6.3 PT0301016 85.09 x 5.33 200.0 179.0 8.1 PT0402000 177.17 x 7.0
105.0 94.0 4.2 PT0201050 91.67 x 3.53 205.0 184.0 8.1 PT0402050 183.52 x 7.0
105.0 89.5 6.3 PT0301050 88.27 x 5.33 210.0 189.0 8.1 PT0402100 183.52 x 7.0
108.0 92.5 6.3 PT0301080 91.44 x 5.33 215.0 194.0 8.1 PT0402150 189.87 x 7.0
110.0 99.0 4.2 PT0201100 98.02 x 3.53 220.0 199.0 8.1 PT0402200 196.22 x 7.0
110.0 94.5 6.3 PT0301100 91.44 x 5.33 230.0 214.5 6.3 PT0302300 208.92 x 5.33
110.0 89.0 8.1 PT0401100 88 x 7.0 230.0 209.0 8.1 PT0402300 208.92 x 7.0
115.0 99.5 6.3 PT0301150 97.79 x 5.33 240.0 219.0 8.1 PT0402400 215.27 x 7.0
120.0 109.0 4.2 PT0201200 107.54 x 3.53 250.0 229.0 8.1 PT0402500 227.97 x 7.0
120.0 104.5 6.3 PT0301200 100.97 x 5.33 250.0 225.5 8.1 PT0802500 215.27 x 7.0
120.0 99.0 8.1 PT0401200 98 x 7.0 250.0 134.5 6.3 PT0302500 234.32 x 5.33
125.0 114.0 4.2 PT0201250 113.89 x 3.53 254.0 233.0 8.1 PT0402540 227.97 x 7.0
125.0 109.5 6.3 PT0301250 107.32 x 5.33 260.0 239.0 8.1 PT0402600 240.67 x 7.0
125.0 104.0 8.1 PT0401250 103 x 7.0 265.0 244.0 8.1 PT0402650 240.67 x 7.0

Latest information available at www.tss.trelleborg.com

32 Edition January 2011
 Turcon® Glyd Ring® T

Bore Groove Groove TSS Part O-Ring Bore Groove Groove TSS Part O-Ring
Dia. Dia. Width No. Dimensions Dia. Dia. Width No. Dimensions
DN H9 d1 h9 L1 +0.2 DN H9 d1 h9 L1 +0.2
268.0 247.0 8.1 PT0402680 240.67 x 7.0 1050.0 1022.0 9.5 PT05X1050 1020 x 8.4
270.0 249.0 8.1 PT0402700 240.67 x 7.0 1065.0 1027.0 13.8 PT06X1065 1025 x 12.0
280.0 259.0 8.1 PT0402800 253.37 x 7.0 1070.0 1032.0 13.8 PT06X1070 1030 x 12.0
290.0 269.0 8.1 PT0402900 266.07 x 7.0 1200.0 1172.0 9.5 PT05X1200 1170 x 8.4
300.0 279.0 8.1 PT0403000 278.77 x 7.0 1200.0 1162.0 13.8 PT06X1200 1160 x 12.0
300.0 275.5 8.1 PT0803000 266.07 x 7.0 1225.0 1187.0 13.8 PT06X1225 1185 x 12.0
304.8 283.8 8.1 PT0403048 278.77 x 7.0 1500.0 1462.0 13.8 PT06X1500 1460 x 12.0
310.0 289.0 8.1 PT0403100 278.77 x 7.0 2000.0 1962.0 13.8 PT06X2000 1960 x 12.0
320.0 299.0 8.1 PT0403200 291.47 x 7.0 2700.0 2662.0 13.8 PT06X2700 2660 x 12.0
320.0 295.5 8.1 PT0803200 291.47 x 7.0
All dimensions in bold type are suitable for installation in
330.0 305.5 8.1 PT0803300 304.17 x 7.0 grooves to ISO 7425/1, bore dia. in accordance with ISO 3320.
Other dimensions and all intermediate sizes up to 2700 mm dia.
340.0 315.5 8.1 PT0803400 316.87 x 7.0 including inch sizes can be supplied.
350.0 325.5 8.1 PT0803500 316.87 x 7.0 All O-Rings with 12 mm cross section are delivered as special
profilring.
360.0 335.5 8.1 PT0803600 329.57 x 7.0
370.0 345.5 8.1 PT0803700 342.27 x 7.0
380.0 355.5 8.1 PT0803800 354.97 x 7.0
400.0 375.5 8.1 PT0804000 367.67 x 7.0
420.0 395.5 8.1 PT0804200 393.07 x 7.0
430.0 405.5 8.1 PT0804300 405.26 x 7.0
440.0 415.5 8.1 PT0804400 405.26 x 7.0
450.0 425.5 8.1 PT0804500 417.96 x 7.0
460.0 435.5 8.1 PT0804600 430.66 x 7.0
480.0 455.5 8.1 PT0804800 456.06 x 7.0
500.0 475.5 8.1 PT0805000 468.76 x 7.0
555.0 530.5 8.1 PT0805550 506.86 x 7.0
600.0 575.5 8.1 PT0806000 557.66 x 7.0
640.0 615.5 8.1 PT0806400 608.08 x 7.0
660.0 635.5 8.1 PT0806600 633.48 x 7.0
700.0 672.0 9.5 PT0507000 670 x 8.4
710.0 682.0 9.5 PT0507100 680 x 8.4
740.0 712.0 9.5 PT0507400 710 x 8.4
780.0 752.0 9.5 PT0507800 750 x 8.4
800.0 772.0 9.5 PT0508000 770 x 8.4
900.0 872.0 9.5 PT0509000 870 x 8.4
1000.0 972.0 9.5 PT05X1000 970 x 8.4
1000.0 962.0 13.8 PT06X1000 960 x 12.0

Latest information available at www.tss.trelleborg.com

Edition January 2011
33
 Turcon® Glyd Ring® T

Latest information available at www.tss.trelleborg.com

34 Edition January 2011