JPegd GR 11 Answer Book (2016)
JPegd GR 11 Answer Book (2016)
JPegd GR 11 Answer Book (2016)
KOPIEREG © JP
INDEX / INHOUDSOPGAWE
CHAPTER / HOOFSTUK 1: MECHANICAL ANALYTICAL / MEGANIES ANALITIES p 1-5
CHAPTER / HOOFSTUK 2: MECHANICAL ASSEMBLY / MEGANIESE SAMESTELLING p 6-17
CHAPTER / HOOFSTUK 3: ISOMETRIC DRAWINGS / ISOMETRIESE TEKENINGE p 18-28
CHAPTER / HOOFSTUK 4: PERSPECTIVE DRAWINGS / PERSPEKTIEF TEKENINGE p 29-43
CHAPTER / HOOFSTUK 5: CIVIL ANALYTICAL / SIVIEL ANALITIES p 44-48
CHAPTER / HOOFSTUK 6: CIVIL DRAWINGS / SIVIELE TEKENINGE p 49-63
CHAPTER / HOOFSTUK 7: SOLID GEOMETRY / VASTE LIGGAME p 64-73
CHAPTER / HOOFSTUK 8: INTERPENETRATION & DEVELOPMENT
DEURDRINGING & ONTWIKKELING p 74-85
CHAPTER / HOOFSTUK 9: TRANSITION PIECES / OORGANGSTUKKE p 86-95
CHAPTER / HOOFSTUK 10: LOCI (HELIX) / LOKUSSE (HELIKS) p 96-103
CHAPTER / HOOFSTUK 11: LOCI (CAM) / LOKUSSE (NOK) p 104-116
COPYRIGHT / KOPIEREG
All rights reserved © JP
No part of this workbook may be reproduced or transmitted in any form or by any means without permission in writing from the
publisher. This includes electronic or mechanical, including photocopying, recording, or any information storage and retrieval system.
Alle regte voorbehou © JP
Geen gedeelte van hierdie werksboek mag sonder die skriftelike toestemming van die uitgewer gereproduseer word of in enige vorm of
deur enige middel weergegee word nie, hetsy deur fotokopiëring, plaat- of bandopname, vermikrofilming of enige ander stelsel
van inligtingsbewaring.
ACKNOWLEDGEMENTS / ERKENINGS
Some of the questions in this book have been contained in previous examination papers and used with the permission of the Executive
Directors of the Independet Examinations Board, Department of Basic Education and South-African Comprehensive Assessment Institute.
Sommige van die vrae in hierdie boek is vervat in vorige eksamenvraestelle, wat met die toestemming van die nodige Uitvoerende
Direkteure van die Onafhanklike Eksamenraad, Departement van basiese onderwys en Suid-Afrikaanse Komprehensiewe assesseringsinstituut.
Reproduced under Goverment Printer's Works Authorization No. 11697 dated 03 September 2014 and No. 11706 dated 20 July 2015.
COPYRIGHT © JP
KOPIEREG © JP
DIFFERENT SECTION / VERSKILLENDE SNITTE
FULL SECTION / VOLSNIT ALIGNED SECTION / IN-LYNGERIGTE SNIT
A
A
SECTION LINES NOT REQUIRED
SNITLYNE NIE NODIG NIE SECTION A-A / SNIT A-A
HALF SECTION / HALFSNIT REMOVED SECTION / WEGSTAANDE SNIT
NOTE: LET WEL:
CHANGE VERANDER NOTE:
CENTRE LINE HARTLYN
TO NA CONTINUOUS
CONTINUOUS DEURLOPENDE THICK LINE
THIN LINE DUNLYN
CORRECT / KORREK INCORRECT / VERKEERD LET WEL:
DEURLOPENDE
DIKLYN
PART SECTION / GEDEELTELIKE SNIT REVOLVED SECTION / GEWENTELDE SNIT
PART SECTION TO
SHOW INTERNAL
DETAIL
NOTE: LET WEL:
CONTINUOUS DEURLOPENDE
GEDEELTELIKE SNIT
THIN LINE DUNLYN
OM INTERNE DETAIL
TE TOON
TRUE EXAMPLE CONVENTION TRUE EXAMPLE CONVENTION
FEATURE / EIENSKAP VIEW / AANSIG FEATURE / EIENSKAP VIEW / AANSIG
WARE VOORBEELD KONVENSIE WARE VOORBEELD KONVENSIE
HOLES ON A
CYLINDRICAL HELICAL LINEAR PITCH
COMPRESSION SPRING (REPEATED FEATURES)
INTERRUPTED VIEW
ON A ROUND SECTION
EXTERNAL SCREW
(S-BREAK)
THREAD
ONDERBROKE AANSIG
BUITESKROEFDRAAD
OP 'N RONDE SNIT
(S-BREEK)
A A
INTERNAL SCREW
SPUR GEAR
THREAD
REGUITTANDRAT
BINNESKROEFDRAAD
A A
SYMMETRY
SYMBOL SPLINED SHAFT
SIMMETRIESE
TREATMENT OF SIMBOOL
SYMMETRICAL RIB-AS
COMPONENTS
SYMMETRY
SYMBOL
BEHANDELING SIMMETRIESE
VAN SIMBOOL
SIMMETRIESE SERRATED SHAFT
KOMPONENTE
RIFFEL-AS
COPYRIGHT © JP
MECHANICAL DRAWINGS
KOPIEREG © JP
CONVENTIONAL REPRESENTATION
MEGANIESE TEKENINGE KONVENSIONELE VOORSTELLINGS
SYMBOLS USED FOR INDICATION SYMBOLS FOR DIRECTION OF LAY METHOD / TREATMENT CRITERION OF ROUGHNESS
OF SURFACE TEXTURE SIMBOLE VIR PATROONRIGTING (LÊRIGTING) METODE / BEHANDELING MAATSTAF VIR GROFHEID
SIMBOLE VIR AANDUIDING VAN
OPPERVLAKTEKSTUUR SYMBOL / SIMBOOL INTERPRETATION / VERTOLKING CHEMICAL HONING Ra = 1 UNIT / EENHEID = µm = 0,0001 mm
CHEMIES SILINDRIESE SLYPWERK
0,025
0,05
ROUGHNESS VALUE
6,3
3,2
1,6
0,8
0,4
0,2
0,1
50
25
Ra = µm
GRINDING MACHINING GROFHEIDSWAARDE
SLYPWERK MASJINERING
ROUGHNESS GRADE
N 12
N 10
N 11
NUMBERS
LAPPING PLATING
N9
N8
N7
N6
N5
N4
N3
N2
N1
APPROXIMATELY
60° FYNSLYP PLATERING GROFHEIDGRAAD-
ONGEVEER NOMMERS
=
PARALLEL
REMOVAL OF MATERIAL / VERWYDERING VAN MATERIAAL PERPENDICULAR
LOODREG
REMOVAL OF MATERIAL NOT PERMITTED
VERWYDERING VAN MATERIAAL NIE TOEGELAAT NIE CROSSED
GEKRUIS
INDICATION OF SPECIAL SURFACE CHARACTERISTICS
MULTI-
AANDUI VAN SPESIALE OPPERVLAKKENMERKE
DIRECTIONAL
M
MEERRIGTING
INDICATION OF SURFACE ROUGHNESS APPOXIMATELY
AANDUI VAN OPPERVLAKGROFHEID
CIRCULAR
a ROUGHNESS VALUE Ra IN MICROMETERS OR ROUGHNESS GRADE NUMBER N1 TO N12
a GROFHEIDWAARDE Ra IN MIKROMETER OF GROFHEIDSGRAADNOMMERS N1 TOT N12
C PRODUCTION METHOD, TREATMENT OR COATING
ONGEVEER
SIRKELVORMIG
b PRODUKSIE METODE, BEHANDELING OF BEDEKLAAG
SAMPLING LENGTH
MAXIMUM (a1) AND MINIMUM (a2) LIMITS OF SURFAC'E ROUGHNESS
MAKSIMUM (a1) EN MINIMUM (a2) GRENSE VIR OPPERVLAKGROFHEID
APPROXIMATELY
RADIAL
c MONSTERNEMINGSLENGTE
DIRECTION OF LAY
a1 d PATROONRIGTING / LÊRIGTING
a2 e MACHINING ALLOWANCE
MASJINERINGSTOELATING
R
ONGEVEER OTHER ROUGHNESS VALUES (IN BRACKETS)
RADIAAL f ANDER GROFHEIDSWAARDES (TUSSEN HAKIES)
MECHANICAL SYMBOLS MACHINING & SURFACE TEXTURE SYMBOLS
MEGANIESE SIMBOLE MASJINERING- & OPPERVLAKTEKSTUURSIMBOLE
TYPES OF WELDS / TIPE LASSE FINISH SYMBOL
WELD SECTIONAL VIEW SYMBOL AFWERKINGSIMBOOL
LAS DEURSNEE AANSIG SIMBOOL
METHOD SYMBOL
SQUARE A J
GROOVE OR BUTT WELDS / GROEF- OF STUIKLASSE
COPYRIGHT © JP
MECHANICAL SYMBOLS
KOPIEREG © JP
WELDING SYMBOL
MEGANIESE SIMBOLE SWEISLASSIMBOOL
260 E QUESTION: ANALYTICAL (MECHANICAL)
+0.25
50 160 -0.30
Given:
A front view, top view and right view of a box and gland assembly, detailed drawing of the flange, a title block and
Ø88 Ø20 a table of questions. The drawings have not been prepared to the indicated scale.
Instructions:
Complete the table below by neatly answering the questions, which all refer to the accompanying drawings and
the title block. [30]
Ø88 Ø76
100
Ø12
QUESTIONS ANSWERS
1 On what date was the drawing approved? 2015-03-03 1
200
32
20
5 On what date was the revision done? 2015-02-03 1
12
10 Name the part at R. STUD 1
8
12 Name the feature at T. S-BREAK 1
20 13 How many surfaces need to be machined? 7 1
D
S
64
7 Angus Street 3 STUD 2 MILD STEEL 1. INSERT SPOT FACE 2015-02-03 ANSWER 19
Pretoria
4 SHAFT 1 HARDENED STEEL REVISIONS DATE
www.jpegd.co.za
012 345 6789 5 BUSH 1 RUBBER DRAWN: HENDRIK 2015-01-01
COPYRIGHT © JP
KOPIEREG © JP
NAME: ANALYTICAL (MECHANICAL)
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
260 E VRAAG: ANALITIES (MEGANIES)
+0.25
50 160 -0.30
Gegee:
'n Vooraansig, bo-aansig en regteraansig van 'n pakbus- en drukstuksamestelling, 'n gedetailleerde tekening van
Ø88 Ø20 die flens, 'n titelblok en 'n tabel met vrae. Die tekeninge is nie volgens die aangetoonde skaal voorberei nie.
Instruksies:
Voltooi die tabel hieronder deur die vrae, wat almal na die bygaande tekeninge en titelblok verwys, netjies te
Ø88 Ø76
100
beantwoord. [30]
Ø12
VRAE ANTWOORDE
1 Op watter datum is die tekening goedgekeur? 2015-03-03 1
200
32
20
5 Op watter datum is die hersiening gedoen? 2015-02-03 1
12
10 Benoem die onderdeel by R. TAPBOUT 1
8
12 Benoem die kenmerk by T. S-BREEK 1
20
13 Hoeveel vlakke moet gemasjineer word? 7 1
D
S
64
COPYRIGHT © JP
KOPIEREG © JP
NAAM: ANALITIES (MEGANIES)
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
144
48
10
2. SPINDLE 1 MILD STEEL Instructions:
B B 3. WOODRUFF KEY 1 HARDENED STEEL Complete the table below by neatly answering the questions, which
Ø13 4. CASTLE NUT 1 HARDENED STEEL all refer to the accompanying drawings and the title block.
A
SECTION A-A 34 5. WASHER 1 MILD STEEL
[25]
VIEW 1 VIEW 2 6. SPILT PIN 1 SPRING STEEL
1
16
R10
G
16
QUESTION ANSWERS
D
16
44
8
C 3 In which street is the manufacturing company situated? GOVAN MBEKI DRIVE 1
VIEW 3
M24 4 Who made changes to the drawing? ARNO 1
19
5 What scale is indicated for the drawing? SCALE 1:2 1
4
Ø5
4
37 6 What is the tolerance allowed on the dimensions? ± 0.15 1
R16 x 10
3 7 If a scale of 1:5 were used, what would a dimension of 10mm read? 10 mm 1
2
10 What is the thickness of the woodruff key? 10 mm 1
Ø48
11 Determine the dimensions at C and D. C: 198 mm D: 76 mm 2
2 Ø160
5
12 What is the size of the arc at E? R3 1
46
Ø28
13 What is the angle / gradient of feature F? 10˚ = (100° - 90°) 1
6 14 What is the feature at G called? Keyway 1
5
Ø24
19
Ø48
Ø16 15 What is the purpose of the castle nut? To secure the handle to the spindle 1
R4
21
DRAWN BY: JOHAN DRAWING NO. 2 MATERIAL: MILD, HARDENED AND SPRING STEEL
UNLESS OTHERWISE
SPECIFIED TOLERANCES DATE: 05/10/2011 FILE NAME: CRANK_003 HEAT TREATMENT: NORMALISE
ON DIMENSIONS ARE
± 0,15
CHECKED BY: LUHAN
GOVAN MBEKI DRIVE
PORT ELIZABETH
DATE:10/10/2011
ALL UNSPECIFIED RADII 6001
ARE R3
APPROVED BY: PIETER www.maxsteel.co.za B B
DRAWING PROGRAM: DATE: 20/10/2011
TurboCAD Pro 17.2
SCALE 1:2
CRANK HANDLE SYMBOL
COPYRIGHT © JP
KOPIEREG © JP
NAME: ANALYTICAL (MECHANICAL)
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
144
VRAAG: ANALITIES (MEGANIES)
Ø76
ONDERDELELYS
Gegee:
16 A ONDERDELE HOEVEELHEID MATERIAAL
R16 Ses onderdele van 'n slinger met 'n titelblok en 'n tabel met vrae.
1. HANDVATSEL 1 SAGTE STAAL
2. SPIL 1 SAGTE STAAL Instruksies:
10
48
Voltooi die onderstaande tabel deur die vrae, wat almal na die
3. WOODRUFF-SPY 1 VERHARDE STAAL
bygaande tekene en titelblok verwys, netjies te
B B 4. KROONMOER 1 VERHARDE STAAL
Ø13 beantwoord.
A 5. WASTER 1 SAGTE STAAL [25]
SNIT A-A 34
6. SPILPEN 1 VEERSTAAL
AANSIG 1 AANSIG 2
1
16
R10
G
16
VRAAG ANTWOORDE
D
16
1 Op watter datum is die tekening geteken? 05/10/2011 1
44
E
2 Wat is die lêernaam van die tekening? SLINGER_003 1
5
8
C 3 In watter straat is die vervaardigingsmaatskappy geleë? GOVAN MBEKIRYLAAN 1
AANSIG 3 4 Wie het veranderinge aan die tekening aangebring? ARNO 1
M24
19
5 Wat is die skaal wat vir die tekening aangedui word? SKAAL 1:2 1
4
Ø5
4 6 Wat is die toelaatbare toleransie op die afmetings? ± 0.15 1
37
R16 x 10 7 Indien 'n skaal van 1:5 gebruik word, wat sal 'n afmeting van 10mm lees? 10 mm 1
3
8 Wat sal AANSIG 3 genoem word? DEURSNEE VOORAANSIG 1
F
9 Hoeveel vlakke moet op AANSIG 4 gemasjineer word? SES 1
0°
44
10
2
10 Wat is die dikte van die woodruff-spy? 10 mm 1
Ø48 11 Bereken die afmetings by C en D. C: 198 mm D: 76 mm 2
2 Ø160
5 12 Wat is die grootte van die boog by E? R3 1
46
Ø28 13 Wat is die skuinste / helling van kenmerk by F? 10˚ = (100° - 90°) 1
Ø48 15 Wat is die doel van die kroonmoer? Om die handvatsel aan die spil te vestig 1
5
COPYRIGHT © JP
KOPIEREG © JP
NAAM: ANALITIES (MEGANIES)
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
Ø64
A Ø30
Ø44 QUESTION: ANALYTICAL (MECHANICAL)
Given:
The working drawing of a diaphragm regulator with a title block
Ø20
M21
and a table of questions.
Instructions:
S S Complete the table below by neatly printing the answers to the
1 questions, which all refer to the accompanying drawings and title
Ø70 block.
[30]
AF 32
VIEW 2 Ø14
QUESTIONS ANSWERS
12
1 On what date was the revision completed? 12/05/2011 1
6
2
2 Who checked the drawing? ARNO 1
M12 x 1,5
3 What is the title of the drawing? DIAPHRAGM REGULATOR 1
E
44
36
SPH Ø10 6 How many internal screw threads are there in the assembly? 5 1
48
57
B 7 How many parts make up the assembly? 10 1
3rd ANGLE ORTHOGRAPHIC
8 What orthographic projection system has been used? PROJECTION 1
F
C 10 What would VIEW 2 be called? TOP VIEW 1
12
20
30
22
COPYRIGHT © JP
KOPIEREG © JP
NAME: ANALYTICAL (MECHANICAL)
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
Ø64
A Ø30
Ø44 VRAAG: ANALITIES (MEGANIES)
Gegee:
Die werkstekening van 'n diafragmareguleerder met 'n titelblok
M21
Ø20
en 'n tabel met vrae.
Instruksies:
S S Voltooi die tabel hieronder deur die antwoorde van die vrae, wat
1 almal na die bygaande tekeninge en titelblok verwys, netjies te
Ø70 drukskryf.
[30]
OK 32
AANSIG 2 Ø14
VRAE ANTWOORDE
12
1 Op watter datum is die hersiening voltooi? 12/05/2011 1
6
2
2 Wie het die tekening nagesien? ARNO 1
M12 x 1,5
3 Wat is die titel van die tekening ? DIAFRAGMAREGULEERDER 1
E
44
36
4 Wat is die skaal wat vir die tekening aangetoon word? 1:2 1
3 Van watter materiaal is die metaalonderdele van die reguleerder
5 GEELKOPER 1
vervaardig?
SPH Ø10 6 Hoeveel interne skroefdrade is daar in die samestelling? 5 1
48
57
B 7 Uit hoeveel onderdele bestaan die samestelling? 10 1
F
C 10 Wat sal AANSIG 2 genoem word? BO-AANSIG 1
12
20
30
22
19 Bepaal die boonste toleransiebeperking vir die afmeting van 34 mm. 34,25 mm 2
Teken, in netjiese vryhand, die eenvoudige SANS 0111- konvensie
20 4
van 'n veer in die onderstaande blok.
12/05/11 MARIE DIAMETER VAN INVOERE A TOTAAL (13) Ø14 ,Ø30 , Ø64 ,Ø20, M 12, 107 30
DATUM VERANDER DEUR BEKRYWING VAN HERSIENING Nr: TEKENPROGRAM: TurboCAD Prof v17.2 TEKENAAR: LUHAN 20/03/11 20.
COPYRIGHT © JP
KOPIEREG © JP
NAAM: ANALITIES (MEGANIES)
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
1 2 QUESTION: ANALYTICAL (MECHANICAL)
E
Given:
10
The views of an adaptor plate with a title block and a table of
13
questions.
14
36
11
Instructions:
B
37
Complete the table below by neatly printing the answers to the
42
32
15
questions, which all refer to the accompanying drawings and title
6
block.
[31]
C D
6 QUESTIONS ANSWERS
VIEW 2
14,47 1 What is the title of the drawing? ADAPTOR PLATE 1
REAM
41 14,27
2 On what date was the drawing checked? 10/01/11 1
Ø30
3 Who approved the drawing? L STEYN 1
4 What is the drawing number? Q1/ERCO/11 1
5 If a scale of 1:5 were used, what would a dimension of 10 mm read? 10 1
6 How many surfaces of the component require machining? 9 1
2
R9
15 7 What process must be applied to achieve the required finish? GRINDING 1
56
Ø5 22 3
As what type of mechanical drawing can the views of the adaptor plate be
8 DETAILED DRAWING 1
classified?
81
9 What would VIEW 2 be called? TOP VIEW 1
15
Ø30
14 What does the circle on the symbol at 4 mean? WELDING ALL AROUND 1
Ø37
A R51 15 What type of section is shown at 5? REVOLVED SECTION 2
5
16 What is the permissible tolerance on the dimensions of the components? 0,3 1
63
17 Determine the tolerance for the dimension at 6. 0,2 2
16,10
REAM
16,02 M4 32 In the box below, draw, in neat freehand, the symbol for the projection
18 4
system used.
VIEW 1 In the block below, draw, in neat freehand, the SANS 0111 convention for
19 5
the given internal screw thread.
TOTAL 31
17/01/11 JOHNNY CHANGE MACHINING SPEC' B
GRINDING
14/01/11 JOHNNY DECREASE RIB THICKNESS A ALL SPECIFIED SURFACE 0,05
DATE CHANGED BY REVISION DESCRIPTION No. FINISHES ARE:
DRAWING No: Q1/ERCO/11 MATERIAL: CAST ALUMINIUM UNLESS OTHERWISE SPECIFIED ALL 18 19
DIMENSIONS ARE IN MILLIMETRES
FILE NAME: ERCO-BL-2011 HEAT TREATMENT: NONE WITH A TOLERANCE OF 0,3.
188 SCHOEMAN STREET DRAWING PROGRAM: TurboCAD Pro 17.2
PRETORIA
0001 DRAWING BY: ARNO BELL 02/01/11
www.egdengineering.co.za
(SA) (PTY) LTD 012 555 2345 CHECKED BY: T MORKEL 10/01/11
TITLE APPROVED BY: L STEYN 14/01/11
SCALE: NTS SYMBOL SANS 0111 - CONVENTION
COPYRIGHT © JP
KOPIEREG © JP
NAME: ANALYTICAL (MECHANICAL)
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
1 2
E VRAAG: ANALITIES (MEGANIES)
Gegee:
10
13
Twee aansigte van 'n passtuk met 'n titelblok en 'n tabel met vrae.
14
36
Instruksies:
11
Voltooi die tabel hieronder deur die antwoorde van die vrae, wat
B
37
almal na die bygaande tekeninge en titelblok verwys, netjies te
42
32
15
drukskryf.
6
[31]
C D
6 VRAE ANTWOORDE
AANSIG 2 1 Wat is die titel van die tekening? PASSTUK 1
14,47
RUIM
41 14,27
2 Op watter datum is die tekening nagesien? 10/01/11 1
Ø30
3 Wie het die tekening goedgekeur? L STEYN 1
4 Wat is die tekeningnommer? Q1/ERCO/11 1
Indien 'n skaal van 1:5 gebruik sou word, wat sal 'n afmeting van 10 mm
5 10 1
lees?
2
6 Hoeveel oppervlaktes van die komponent moet gemasjineer word? 9 1
15
R9
56
Ø5 22 7 Watter proses moet aangewend word om die verlangde afwerking te verkry? SLYP 1
3
As watter tipe meganiese tekening kan die aansigte van die passtuk
81
8 GEDETAILLEERDE TEKENING 1
geklassifiseer word?
15
COPYRIGHT © JP
KOPIEREG © JP
NAAM: ANALITIES (MEGANIES)
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
QUESTION: ANALYTICAL (MECHANICAL)
32 Given:
24 R20 A table of questions and a working drawing.
Ø20
R12 Instructions:
R12 Complete the table below by answer the questions, which all refer to the accompanying drawings
and the title block. [28]
A R8
R20 QUESTION: ANSWERS:
28
1 On what date was the drawing first completed? 20/02/08 1
28
P
56
180
92 3 What is the drawing number? S8/ED/01 1
F 4 How many revisions have been made to the drawing? 1 1
Ø96
89
B 5 Where is the manufacturing company situated? GOODWOOD 1
70
25
14 Name the type of section on VIEW 1. ALIGNED SECTION 1
12
20
40
20 In the box below and in freehand, neatly draw the SANS 0111 convention used for the feature at B. 3
15/10/08 KARIN GROOVE ON HUB A
TOTAL (15) P= 96 mm, Q= 56 mm, R=30 mm 28
DATE CHANGED BY DESCRIPTION OF REVISION No
UNLESS OTHERWISE DRAWN: COLEEN DRAWING No: S8/ED/01 MATERIAL: CAST IRON 19 20
SPECIFIED ALL
DIMENSIONS ARE IN DATE: 20/02/08 FILE NAME: S-P2-A2 HEAT TREATMENT: NORMALISE
MILLIMETRES WITH A 18
TOLERANCE OF ±0,25. CHECKED: KARL FORESTRY DRIVE
GOODWOOD
ALL UNSPECIFIED DATE: 26/02/08
5240
RADII ARE R3 www.capesteel.co.za
APPROVED: JAN
DATE: 01/03/08
DRAWING PROGRAM:
TurboCAD Pro v17.2 SCALE: N.T.S
BELL CRANK SYMBOL Convention of feature B
COPYRIGHT © JP
KOPIEREG © JP
NAME: ANALYTICAL (MECHANICAL)
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
VRAAG: ANALITIES (MEGANIES)
32 Gegee:
24 R20
'n Tabel met vrae en 'n werkstekening.
Ø20
R12
Instruksies:
R12 Voltooi die tabel hieronder deur die vrae, wat almal na die bygaande tekeninge en titelblok verwys,
netjies te beantwoord. [28]
A R8
R20 VRAE: ANTWOORDE:
28
1 Op watter datum is die tekening die eerste keer voltooi? 20/02/08 1
28
P
56
180
92 3 Wat is die tekeningnommer? S8/ED/01 1
F 4 Hoeveel keer is die tekening verander? 1 1
Ø96
89
B 5 Waar is die vervaardigingsmaatskappy geleë? GOODWOOD 1
70
25
14 Benoem die tipe snit op AANSIG 1. LYNGERIGTE SNIT 1
12
20
40
TENSY ANDERS VERMELD, TEKENAAR: COLEEN TEKENING Nr: S8/ED/01 MATERIAAL: GIETYSTER 19 20
IS ALLE AFMETINGS IN
DATUM: 20/02/08 LÊERNAAM: S-P2-A2 HITTEBEHANDELING: NORMALISEER
MILLIMETER MET 'N 18
TOLERANSIE VAN ±0,25. NAGESIEN: KARL FORESTRYLAAN
ALLE GOODWOOD
DATUM: 26/02/08
ONGESPESIFISEERDE 5240
www.capesteel.co.za
RADIUSSE IS R3 GOEDGEKEUR: JAN
DATUM: 01/03/08
TEKENPROGRAM:
TurboCAD PRO v17.2 SKAAL: N.V.S
KLOKKRUK SIMBOOL Konvensie van kenmerk B
COPYRIGHT © JP
KOPIEREG © JP
NAAM: ANALITIES (MEGANIES)
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
S S
1.5 x D 1.5 x D
AF
OK
AF (ACROSS FLATS)
OK (OORKANTS)
(60˚) (30˚)
SHOWS THREE FACES
OF THE BOLT HEAD SHOWS TWO FACES
OF THE BOLT HEAD
HEAD HEIGHT: KOPHOOGTE:
0,7 x D = BOLT (30˚)
*R1 *R1 0,7 x D = BOUT
0,8 x D = NUT 0,8 x D = MOER
*R3 *R3
(60˚) (60˚) (60˚)
*R2
TOON TWEE VLAKKE
TOON DRIE VLAKKE
VAN DIE BOUTKOP
VAN DIE BOUTKOP
1.5 x D * USE R1, R2 & R3 TO
AF
DRAW THE ARCS ON
(ACROSS FLATS)
THE HEADS!
OK
* GEBRUIK R1, R2 &
(OORKANTS)
D R3 OM DIE BOË OP
DIE KOPPE TE
TEKEN!
0,7 x D
ALTERNATIVE /
ALTERNATIEF
BOLT LENGTH / BOUTLENGTE
BOLT / (60˚)
SKROEFDRAADLENGTE
BOUT
THREAD LENGTH
0,1 x D
(2 x D)
(45˚)
HEXAGONAL NUT SESKANTIGE MOER
CHAMFER BOTH BEIDE KANTE
SIDES AFGESKUINS
WASHER / 0,2 x D
WASTER 2xD
LOCKNUT / 0,5 x D
SLUITMOER
NUT /
MOER 0,8 x D
COPYRIGHT © JP
KOPIEREG © JP
ENGINEERING GRAPHICS & DESIGN / INGENIEURSGRAFIKA & ONTWERP
HEXAGONAL BOLT, NUT, LOCKNUT & WASHER / SESKANTIGE BOUT, MOER, SLUITMOER & WASTER
Ø42 Ø24 8 QUESTION: MECHANICAL ASSEMBLY
Ø44
M24 Ø158
Given:
* The exploded isometric drawing of the parts of a pulley
assembly, showing the position of each part relative to all
Ø143 the others
Ø24
* Orthographic views of each of the parts of the pulley
Ø32 assembly
15
Instructions:
3
* Answer this question on page 7
33
M24 NUT (1) WASHER (2)
37
* Draw, to scale 2 : 1 and in third-angle orthographic
projection, the following view of the assembled parts of
the pulley assembly:
BUSH (4) A A A sectional front view on cutting plane A-A, as seen from
the direction of the arrow shown on the exploded isometric
1 Ø122 drawing. The cutting plane, which passes through the
vertical centre line of the assembly, is shown on the top
view of the pulley (part 3).
2 M24 * ALL drawings must comply with the quidelines contained
in the SANS 10111.
NOTE:
* Show THREE faces of the M24 nut and ALL necessary
construction.
24
15
6
* NO hidden detail is required.
3
45
13
33
25
Ø32
82
Ø9 Ø54
PULLEY (3)
4
15
4 96
Ø32
Ø54 Ø32
SHAFT (7)
PARTS LIST
PART QUANTITY MATERIAL
M9
1 M24 NUT 1 MILD STEEL
20
2 WASHER 1 MILD STEEL
5 3 PULLEY 1 CAST IRON
4 BUSH 1 BRONZE
5 BRACKET 1 CAST IRON
75 6 GRUB SCREW 1 MILD STEEL
SLOT 2 x 2 7 SHAFT 1 MILD STEEL
Ø24
8 ANDROMEDA STREET
GEZINA
8
M9
19
DURBAN
7 12 0084
6
9
073 675 3111
GRUB SCREW (6) M8 M8
BRACKET (5)
PULLEY ASSEMBLY
EXPLODED ISOMETRIC DRAWING ALL DIMENSIONS ARE ALL UNSPECIFIED
IN MILLIMETRES RADII ARE R3
COPYRIGHT © JP
KOPIEREG © JP
NAME: MECHANICAL ASSEMBLY
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
Ø42 Ø24 8 VRAAG: MEGANIESE SAMESTELLING
Ø44
M24 Ø158
Gegee:
* Die uitskuif- isometriese tekening van die onderdele van
'n katrolsamestelling, wat die posisie van elke onderdeel
Ø143 relatief tot al die ander toon
Ø24
* Ortografiese aansigte van elke onderdeel van die
Ø32 katrolsamestelling
15
Instruksies:
3
* Beantwoord hierdie vraag op bladsy 7
33
M24-MOER (1) WASTER (2)
37
* Teken, volgens skaal 2 : 1 en in derdehoekse
ortografiese projeksie, die volgende aansig van die
saamgestelde onderdele van die katrolsamestelling:
BUS (4) A A 'n Deursnee-vooraansig volgens snyvlak A-A, soos
gesien vanuit die rigting van die pyl wat in die uitskuif-
1 Ø122 isometriese tekening getoon word. Die snyvlak, wat deur
die vertikale senterlyn van die samestelling gaan, word op
die bo-aansig van die katrol (onderdeel 3) getoon.
2 M24 * ALLE tekene moet voldoen aan die riglyne vervat in die
SANS 10111.
LET WEL:
* Toon DRIE vlakke van die M24-moer en ALLE nodige
konstruksies.
15
24
6
* Geen verborge besonderhede word verlang nie.
3
45
13
33
25
Ø32
82
Ø54
Ø9
KATROL (3)
4
15
4 96
Ø32
Ø54 Ø32
AS (7)
LYS VAN ONDERDELE
ONDERDEEL HOEVEELHEID MATERIAAL
1 M24-MOER 1 SAGTE STAAL
M9
20
2 WASTER 1 SAGTE STAAL
5 3 KATROL 1 GIETYSTER
4 BUS 1 BRONS
5 STEUNSTUK 1 GIETYSTER
75 6 SKROEFTAP 1 SAGTE STAAL
GLEUF 2 x 2 7 AS 1 SAGTE STAAL
Ø24
ANDROMEDASTRAAT 8
GEZINA
8
M9
19
DURBAN
7 12 0084
6
9
073 675 3111
SKROEFTAP (6) M8 M8
STEUNSTUK (5)
KATROLSAMESTELLING
ALLE AFMETINGS ALLE
UITSKUIF-ISOMETRIESE TEKENING IS IN ONGESPESIFISEERDE
MILLIMETER RADIUSSE IS R3.
COPYRIGHT © JP
KOPIEREG © JP
NAAM: MEGANIESE SAMESTELLING
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
RUBRIC CORRECTNESS
OUTSTANDING
VERY GOOD
GOOD
VERY BAD
NON COMPLIANCE NC
QUALITY & NEATNESS
OUTSTANDING
VERY BAD
NON COMPLIANCE NC
TOTAL 10
COPYRIGHT © JP
KOPIEREG © JP
NAME: MECHANICAL ASSEMBLY
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
RUBRIEK KORREKTHEID
UITSTEKEND
BAIE GOED
GOED
BAIE SWAK
NIE VOLDOEN NV
KWALITEIT & NETHEID
UITSTEKEND
BAIE SWAK
NIE VOLDOEN NV
TOTAAL 10
COPYRIGHT © JP
KOPIEREG © JP
NAAM: MEGANIESE SAMESTELLING
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
QUESTION: MECHANICAL ASSEMBLY
10 10
A 60 100
Ø70 44 84 Given:
* The exploded isometric drawing of the parts of a
skateboard wheel assembly, showing the position of
10
each part relative to all the others
* Orthographic views of each of the parts of the skateboard
Ø40
Ø20
wheel assembly
40
Ø10 8
35
28
Instructions:
Ø64 * Answer this question on page 9
M20 * Draw, to scale 1 : 1 and in third-angle orthographic
3 29
A 30 BASE (6) projection, the following views of the assembled parts of
35 the skateboard wheel assembly:
A sectional front view on cutting plane A-A, as seen from
WHEEL (4) the direction of the arrow shown on the exploded isometric
drawing. The cutting plane, which passes through the
60
vertical centre line of the assembly, is shown on the right
30 30
view of the wheel (part 4).
M20 M20 * ALL drawings must comply with the quidelines contained
in the SANS 10111.
22
NOTE:
* Show TWO faces of the M20 nut on the left.
* Show THREE faces of the M20 nut on the right.
15
Ø6
Ø40 * The ball bearing on the left must be drawn in detail.
10
* The ball bearing on the right must be drawn according to
the SANS 10111 convention.
15
Ø34
Ø26
Ø20
2
Ø40
PARTS LIST
PART QUANTITY MATERIAL
1 M20 NUT 2 MILD STEEL
6 2 WASHER 2 MILD STEEL
1 Ø20
3 BALL BEARING 4 CAST IRON
2 4 WHEEL 2 BRONZE
3 4 WASHER (2)
5 SHAFT 1 CAST IRON
4 3 6 BASE 1 MILD STEEL
2 16 8 ANDROMEDA STREET
1 M20
GEZINA
DURBAN
5 0084
FR
073 675 3111
ON
T VI
EW SKATEBOARD WHEEL ASSEMBLY
M20 NUT (1)
EXPLODED ISOMETRIC DRAWING ALL DIMENSIONS ARE ALL UNSPECIFIED
IN MILLIMETRES RADII ARE R3
COPYRIGHT © JP
KOPIEREG © JP
NAME: MECHANICAL ASSEMBLY
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
VRAAG: MEGANIESE SAMESTELLING
10 10
A 60 100
Ø70 44 84 Gegee:
* Die uitskuif- isometriese tekening van die onderdele van
'n skaatsplankwielsamestelling, wat die posisie van elke
10
onderdeel relatief tot al die ander toon
* Ortografiese aansigte van elke onderdeel van die
Ø40
Ø20
skaatsplankwielsamestelling
40
Ø10 8
35
28
Instruksies:
Ø64 * Beantwoord hierdie vraag op bladsy 9
M20 * Teken, volgens skaal 1 : 1 en in derdehoekse
3 29
A 30 BASIS (6) ortografiese projeksie, die volgende aansigte van die
35 saamgestelde onderdele van die
skaatsplankwielsamestelling:
WIEL (4) 'n Deursnee-vooraansig volgens snyvlak A-A, soos
gesien vanuit die rigting van die pyl wat in die uitskuif-
60
isometriese tekening getoon word. Die snyvlak, wat deur
30 30
die vertikale senterlyn van die samestelling gaan, word op
M20 M20 die regteraansig van die wiel (onderdeel 4) getoon.
* ALLE tekene moet voldoen aan die riglyne vervat in die
SANS 10111.
22
LET WEL:
* Toon TWEE vlakke van die M20-moer aan die linkerkant.
15
Ø6
Ø40 * Toon DRIE vlakke van die M20-moer aan die regterkant.
10
* Teken die koeëllaer aan die linkerkant gedetailleerd.
* Teken die koeëllaer aan die regterkant volgens die SANS
15
Ø34
Ø26
Ø20
10111 konvensie.
M20
* Geen verborge besonderhede word verlang nie.
Ø30
30 SSD
10 22 35 30 40 30 35 22
2
Ø40
COPYRIGHT © JP
KOPIEREG © JP
NAAM: MEGANIESE SAMESTELLING
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
RUBRIC CORRECTNESS
OUTSTANDING
VERY GOOD
GOOD
VERY BAD
NON COMPLIANCE NC
QUALITY & NEATNESS
OUTSTANDING
VERY BAD
NON COMPLIANCE NC
TOTAL 10
COPYRIGHT © JP
KOPIEREG © JP
NAME: MECHANICAL ASSEMBLY
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
RUBRIEK KORREKTHEID
UITSTEKEND
BAIE GOED
GOED
BAIE SWAK
NIE VOLDOEN NV
KWALITEIT & NETHEID
UITSTEKEND
BAIE SWAK
NIE VOLDOEN NV
TOTAAL 10
COPYRIGHT © JP
KOPIEREG © JP
NAAM: MEGANIESE SAMESTELLING
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
30
60 QUESTION: MECHANICAL ASSEMBLY
10
14 Ø44 4 WIDE x 4 DEEP
R11
Ø14
Given:
Ø112 * The exploded isometric drawing of the parts of a
A pulley assembly, showing the position of each part
Ø84
R35 relative to all the others
5 * Orthographic views of each of the parts of the pulley
assembly
Instructions:
Ø14
31
Ø42
100
128
* Answer this question on page 11
* Draw, to scale 1 : 1 and in third-angle orthographic
Ø36
projection, the following views of the assembled parts of
Ø28
the pulley assembly:
A sectional front view on cutting plane A-A, as seen from
A the direction of the arrow shown on the exploded isometric
4
drawing. The cutting plane, which passes vertically through
the centre of the assembly, is shown on the left view of the
35 51 R8 5 5 housing (part 6).
The left view
PULLEY (3) * ALL drawings must comply with the quidelines contained
HOUSING (6) WOODRUFF KEY (5)
in the SANS 10111.
121 NOTE:
15 5 55
* Show THREE faces of the nut in the front view and ALL
Ø28 Ø42 Ø26 necessary construction.
11
* NO hidden detail is required.
5
R8
M14
Ø26
Add the following features to the drawing:
14
M14 * The cutting plane A-A.
Ø14 Ø30 2
Ø42
Ø36 * Label the sectional view SECTION A-A.
51
17 30 55 14
M14 NUT (1) WASHER (2)
SHAFT (4) BUSH (7)
PARTS LIST
PART QUANTITY MATERIAL
5 1
2
M14 NUT
WASHER
1
1
MILD STEEL
MILD STEEL
4 3 PULLEY 1 CAST IRON
7 4 SHAFT 1 MILD STEEL
5 WOODRUFF KEY 1 MILD STEEL
3 6 HOUSING 1 CAST IRON
7 BUSH 1 BRASS
6 7 ANGUS STREET
2 VRYBURG
1 6800
www.igoingenieurs.co.za
012 767 2345
PULLEY ASSEMBLY
ALL DIMENSIONS DRAWING PROGRAM:
EXPLODED ISOMETRIC DRAWING ARE IN
MILLIMETRES TurboCAD Pro v21.2
COPYRIGHT © JP
KOPIEREG © JP
NAME: MECHANICAL ASSEMBLY
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
30
60 VRAAG: MEGANIESE SAMESTELLING
10
14 Ø44 4 WYD x 4 DIEP
R11
Ø14
Gegee:
Ø112 * Die uitskuif- isometriese tekening van die onderdele van
A 'n katrolsamestelling, wat die posisie van elke
Ø84
R35 onderdeel relatief tot al die ander toon
5 * Ortografiese aansigte van elke onderdeel van die
katrolsamestelling
Instruksies:
Ø14
31
Ø42
100
128
* Beantwoord hierdie vraag op bladsy 11
* Teken, volgens skaal 1 : 1 en in derdehoekse
Ø36
ortografiese projeksie, die volgende aansigte van die
Ø28
saamgestelde onderdele van die katrolsamestelling:
'n Deursnee-vooraansig volgens snyvlak A-A, soos
A gesien vanuit die rigting van die pyl wat op die uitskuif-
4
isometriese tekening getoon word. Die snyvlak, wat
vertikaal deur die middel van die samestelling gaan, word
35 51 R8 5 5 op die linkeraansig van die omhulsel (onderdeel 6) getoon.
Die linkeraansig
KATROL (3) * ALLE tekene moet voldoen aan die riglyne vervat in die
OMHULSEL (6) WOODRUFF SPY (5)
SANS 10111.
5
M14 R8
Ø26
Voeg die volgende kenmerke by die tekening:
14
M14 * Die snyvlak A-A.
Ø14 Ø30 2
Ø42
Ø36 * Benoem die deursnee-aansig SNIT A-A.
51
17 30 55 14
M14-MOER (1) WASTER (2)
AS (4) BUS (7)
KATROLSAMESTELLING
ALLE AFMETINGS
TEKENPROGRAM:
UITSKUIF-ISOMETRIESE TEKENING IS IN
MILLIMETER TurboCAD Pro v21.2
COPYRIGHT © JP
KOPIEREG © JP
NAAM: MEGANIESE SAMESTELLING
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
RUBRIC CORRECTNESS
OUTSTANDING
VERY GOOD
GOOD
VERY BAD
NON COMPLIANCE NC
QUALITY & NEATNESS
OUTSTANDING
A
VERY BAD
NON COMPLIANCE NC
TOTAL 10
A
SECTION A-A
COPYRIGHT © JP
KOPIEREG © JP
NAME: MECHANICAL ASSEMBLY
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
RUBRIEK KORREKTHEID
UITSTEKEND
BAIE GOED
GOED
BAIE SWAK
NIE VOLDOEN NV
KWALITEIT & NETHEID
UITSTEKEND
A
BAIE SWAK
NIE VOLDOEN NV
TOTAAL 10
A
SNIT A-A
COPYRIGHT © JP
KOPIEREG © JP
NAAM: MEGANIESE SAMESTELLING
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
6 x M10 HOLES EQUALLY SPACED ON 128 PCD
9
QUESTION: MECHANICAL ASSEMBLY
10
50
Ø150
Given:
8 Ø50
* The exploded isometric drawing of the parts of an overhead swivel
Ø30 Ø6
pulley, showing the position of each part relative to all the others.
* Orthographic views of each of the parts of the overhead swivel
pulley.
PIN (10)
A A Instructions:
Ø30 Ø50 * Answer this question on page 13
Draw, to scale 1 : 1, and in third-angle orthographic projection, the
following view of the assembled parts of the overhead swivel pulley:
Ø106 A sectional front view on A-A as seen from the arrow indicated in
4 the exploded isometric drawing. The vertical cutting plane passes
through the centre line of the assembly as shown on the top view of
6 Ø6 the mounting plate.
7
17
12
14
NOTE:
8
* Show THREE faces of the M18 nut and ALL necessary
MOUNTING PLATE (8) COLLAR (9) construction must be shown.
* ALL drawings must comply with the guidelines contained in the
1 Ø60
SANS 0111.
3 2 x 2 CHAMFER Ø50
2 106 Ø30
14
12
36
Ø6
46
20
M18-NUT (7)
3 14 14 10
90
3
5
80
Ø40
11
Ø18
Ø18 Ø40
18 48 18 WASHER (6)
29
4
3. BUSH 2 BRASS
Ø92
4. HANGER BRACKET 1 MILD STEEL
Ø18
KEY (2) 5. PULLEY 1 CAST IRON
BUSH (3)
Ø40 6. WASHER 1 SPRING STEEL
7. M18 NUT 1 MILD STEEL
Ø104
CHECKED: JOHAN
ENGINEERS 777 www.JPEGD.co.za
30 ALL UNSPECIFIED TITLE:
8 DATE: 24/09/13
RADII ARE R3
5 105 26 APPROVED: SAREL
42 OVERHEAD SWIVEL PULLEY
DRAWING PROGRAM: DATE: 28/09/13
SHAFT (1) PULLEY (5)
TurboCAD Pro v17.2 SCALE: 1:1
COPYRIGHT © JP
KOPIEREG © JP
NAME: MECHANICAL ASSEMBLY
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
6 x M10-GATE EWEREDIG GESPASIEER OP 128 SSD
9
VRAAG: MEGANIESE SAMESTELLING
10
50
Ø150
Gegee:
8 Ø50
* Die uitskuif- isometriese tekening van die onderdele van 'n
Ø30 Ø6
oorhoofseswaaikatrol wat die posisie van elke onderdeel relatief
tot al die ander toon.
* Ortografiese aansigte van elke onderdeel van die
PEN (10)
oorhoofseswaaikatrol.
A A
Ø30 Ø50 Instruksies:
* Beantwoord hierdie vraag op bladsy 13
* Teken, volgens skaal 1 : 1, en in derdehoekse ortografiese
Ø106 projeksie, die volgende aansig van die saamgestelde dele van die
4 oorhoofseswaaikatrol:
'n Deursnee-vooraansig volgens snyvlak A-A, soos gesien
6 Ø6 vanaf die rigting van die pyl getoon in die uitskuif- isometriese
7 tekening. Die vertikale snyvlak gaan deur die senterlyn van die
17
12
14
samestelling soos op die bo-aansig van die monteerplaat aangedui.
8
MONTEERPLAAT (8) RING (9) LET WEL:
* Toon DRIE vlakke van die M18 moer en ALLE nodige konstruksies
1 Ø60
moet getoon word.
3 2 x 2 AFSKUINSING Ø50 * ALLE tekene moet voldoen aan die riglyne vervat in die
2 106 Ø30
14 SANS 0111.
12
36
Ø6
46
20
M18-MOER (7)
3 14 14 10
90
3
5
80
Ø40
11
Ø18
Ø18 Ø40
18 48 18 WASTER (6)
29
4
3. BUS 2 GEELKOPER
Ø92
4. HANGRAAM 1 SAGTE STAAL
Ø18
SPY (2) 5. KATROL 1 GIETYSTER
BUS (3)
Ø40 6. WASTER 1 VEERSTAAL
7. M18-MOER 1 SAGTE STAAL
Ø104
Ø24
IS IN MILLIMETER
DATUM: 28/08/13 PRETORIA
M18
Ø40
NAGESIEN: JOHAN
INGENIEURS 777 www.JPEGD.co.za
ALLE TITEL:
30
8 ONGESPESIFISEERDE DATUM: 24/09/13
5 105 26 RADIUSSE IS R3 GOEDGEKEUR: SAREL
42 OORHOOFSE SWAAIKATROL
TEKENPROGRAM: DATUM: 28/09/13
AS (1) KATROL (5)
TurboCAD Pro v17.2 SKAAL 1:1
COPYRIGHT © JP
KOPIEREG © JP
NAAM: MEGANIESE SAMESTELLING
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
RUBRIC CORRECTNESS
OUTSTANDING
VERY GOOD
GOOD
VERY BAD
NON COMPLIANCE NC
QUALITY & NEATNESS
OUTSTANDING
VERY BAD
NON COMPLIANCE NC
TOTAL 10
SECTION A-A
COPYRIGHT © JP
KOPIEREG © JP
NAME: MECHANICAL ASSEMBLY
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
RUBRIEK KORREKTHEID
UITSTEKEND
BAIE GOED
GOED
BAIE SWAK
NIE VOLDOEN NV
KWALITEIT & NETHEID
UITSTEKEND
BAIE SWAK
NIE VOLDOEN NV
TOTAAL 10
SNIT A-A
COPYRIGHT © JP
KOPIEREG © JP
NAAM: MEGANIESE SAMESTELLING
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
7 QUESTION: MECHANICAL ASSEMBLY
Ø22
Given:
6 Ø62
* The exploded isometric drawing of the parts of a vertical
Ø44 Ø44 support bracket, showing the position of each part
Ø36
relative to all the others
* Orthographic views of each of the parts of the vertical
5 support bracket
Instructions:
* Answer this question on page 15
* Draw, to scale 1 : 1 and in third-angle orthographic
4 Ø76
Ø56 M22
projection, the following views of the assembled parts of
the vertical support bracket:
4
A sectional front view on cutting plane A-A, as seen from
Ø94 the direction of the arrow shown on the exploded isometric
drawing. The cutting plane, which passes through the
11
vertical centre line of the assembly, is shown on the top
14
22
4
15
view of the support bracket (part 1).
36
76
(7) M22-NUT The top view.
* ALL drawings must comply with the quidelines contained
( 4) PULLEY KEYWAY 2 x 4 in the SANS 10111.
3 NOTE:
(3) BUSH Ø44
* Show THREE faces of the M24 nut and ALL necessary
Ø22
construction.
* NO hidden detail is required.
88
Add the following features to the drawing:
* The cutting plane A-A.
64 * Label the sectional view SECTION A-A.
(6) WASHER
4
Ø36
Ø10 M22
2
R12 Ø12 KEYWAY 2 x 4
PARTS LIST
10
70
94
A A PART QUANTITY MATERIAL
Ø44 4
1. SUPPORT BRACKET 1 CAST IRON
2. SHAFT 1 MILD STEEL
30
Ø62 2 3. BUSH 1 BRASS
1
4
R12
4. PULLEY CAST IRON
5. KEY 1 MILD STEEL
20
20
6. WASHER 1 SPRING STEEL
(5) KEY
7. M22 NUT 1 MILD STEEL
10
PRETORIA
66
0001
10
85
10 012 555 2345
35
54 37
BRACKET DATE: 27/08/2012
COPYRIGHT © JP
KOPIEREG © JP
NAME: MECHANICAL ASSEMBLY
GRADE 12:
ENGINEERING GRAPHICS & DESIGN DATE:
7 VRAAG: MEGANIESE SAMESTELLING
Ø22
Gegee:
6 Ø62
* Die uitskuif- isometriese tekening van die onderdele van
Ø44 Ø44 'n vertikale steunstut, wat die posisie van elke onderdeel
Ø36
relatief tot al die ander toon
* Ortografiese aansigte van elke onderdeel van die
5 vertikale steunstut
Instruksies:
* Beantwoord hierdie vraag op bladsy 15
* Teken, volgens skaal 1 : 1 en in derdehoekse
4 Ø76
Ø56 M22
ortografiese projeksie, die volgende aansigte van die
saamgestelde onderdele van die vertikale steunstut:
4
'n Deursnee-vooraansig volgens snyvlak A-A, soos
Ø94
gesien vanuit die rigting van die pyl wat in die uitskuif-
isometriese tekening getoon word. Die snyvlak, wat deur
11
die vertikale senterlyn van die samestelling gaan, word op
14
22
4
15
36
die bo-aansig van die steunstut (onderdeel 1) getoon.
76
(7) M22-MOER Die bo-aansig.
* ALLE tekene moet voldoen aan die riglyne vervat in die
(4) KATROL SPYGLEUF 2 x 4 SANS 10111.
3 LET WEL:
(3) BUS Ø44
* Toon DRIE vlakke van die M24-moer en ALLE nodige
Ø22 konstruksies.
* Geen verborge besonderhede word verlang nie.
4
Ø36 (6) WASTER
Ø10 M22
2
10
70
94
A A
LYS VAN ONDERDELE
Ø44 4 ONDERDEEL HOEVEELHEID MATERIAAL
1. STEUNSTUT 1 GIETYSTER
30
Ø62 2
2. AS 1 SAGTE STAAL
3. BUS 1 GEELKOPER
4
R12 4. KATROL 1 GIETYSTER
20
20
5. SPY 1 SAGTE STAAL
6. WASTER 1 VEERSTAAL
(5) SPY 7. M22 MOER 1 SAGTE STAAL
10
1 SCHOEMANSTRAAT 188
30
PRETORIA
66
10
M12
0001
www.igoingenieurs.co.za
85
10 (SA) (Edms.) Bpk.
012 555 2345
35
10
GOEDGEKEUR: SAREL
54 37 VERTIKALE STEUNSTUT DATUM: 27/08/2012
COPYRIGHT © JP
KOPIEREG © JP
NAAM: MEGANIESE SAMESTELLING
GRAAD 12:
INGENIEURSGRAFIKA & ONTWERP DATUM:
RUBRIC CORRECTNESS
OUTSTANDING
VERY GOOD
GOOD
VERY BAD
NON COMPLIANCE NC
QUALITY & NEATNESS
OUTSTANDING
VERY BAD
A A NON COMPLIANCE NC
TOTAL 10
SECTION A-A
COPYRIGHT © JP
KOPIEREG © JP
NAME: MECHANICAL ASSEMBLY
GRADE 12:
ENGINEERING GRAPHICS & DESIGN DATE:
RUBRIEK KORREKTHEID
UITSTEKEND
BAIE GOED
GOED
BAIE SWAK
NIE VOLDOEN NV
KWALITEIT & NETHEID
UITSTEKEND
BAIE SWAK
A A NIE VOLDOEN NV
TOTAAL 10
SNIT A-A
COPYRIGHT © JP
KOPIEREG © JP
NAAM: MEGANIESE SAMESTELLING
GRAAD 12:
INGENIEURSGRAFIKA & ONTWERP DATUM:
2 16
13
Ø28
21 23
Ø22 QUESTION: MECHANICAL ASSEMBLY
M16
2
Ø16
Given:
M16
* The exploded isometric drawing of the parts of a spur
Ø22 gear assembly, showing the position of each part relative
Ø30 14 to all the others
14
M16 NUT (1) WASHER (2) BUSH (5) 79 * Orthographic views of each of the parts of the spur gear
104 assembly
4
Ø118 A sectional front view on cutting plane A-A, as seen from
KEY (7) the direction of the arrow shown on the exploded isometric
8
SPY GLEUF
drawing. The cutting plane, which passes through the
2x2 vertical centre line of the assembly, is shown on the left
view of the bracket (part 3).
The left view.
* ALL drawings must comply with the quidelines contained
in the SANS 10111.
Ø22
NOTE:
* Show THREE faces of the M16 nut and ALL necessary
Ø82
construction.
110 SSD
4 * Draw the conventional representation of the spur gear in
7 accordance with the SANS 10111.
* NO hidden detail is required.
6 Ø42
25
Add the following features to the drawing:
5 33
* The cutting plane A-A
* Label the sectional view SECTION A-A
SPUR GEAR (4)
5
22 33 16
6
Ø16 A
3 Ø42 Ø28
PARTS LIST
PART QUANTITY MATERIAL
2 1 M24 NUT 1 MILD STEEL
1 2
3
WASHER
BRACKET
1
1
SPRING STEEL
CAST IRON
4 SPUR GEAR 1 MILD STEEL
5 BUSH 2 BRONZE
6 6 SHAFT 1 MILD STEEL
81
6 12 41 12 15 22
7 KEY 1 MILD STEEL
12
7 AVENUE
BLIKKIESDORP
15
VRYBURG
7
5
0084
A 117
082 345 6789
64 139
70
76
SPUR GEAR ASSEMBLY
82
BRACKET (3) ALL DIMENSIONS ARE ALL UNSPECIFIED
EXPLODED ISOMETRIC DRAWING IN MILLIMETRES RADII ARE R3
COPYRIGHT © JP
KOPIEREG © JP
NAME: MECHANICAL ASSEMBLY
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
2 16
13
Ø28
21 23
Ø22 VRAAG: MEGANIESE SAMESTELLING
M16
2
Ø16
Gegee:
M16
* Die uitskuif- isometriese tekening van die onderdele van
Ø22 'n reguittandrat-samestelling, wat die posisie van elke
Ø30 14 onderdeel relatief tot al die ander toon
14
M16-MOER (1) WASTER (2) BUS (5) 79 * Ortografiese aansigte van elke onderdeel van die
104 reguittandrat-samestelling
AS (6) Instruksies:
* Beantwoord hierdie vraag op bladsy 17
21 2 22 * Teken, volgens skaal 1 : 1 en in derdehoekse
ortografiese projeksie, die volgende aansigte van die
14
saamgestelde onderdele van die
4
Ø118 reguittandrat-samestelling:
SPY (7) 'n Deursnee-vooraansig volgens snyvlak A-A, soos
8
SPY GLEUF
gesien vanuit die rigting van die pyl wat in die uitskuif-
2x2 isometriese tekening getoon word. Die snyvlak, wat deur
die vertikale senterlyn van die samestelling gaan, word op
die linkeraansig van die steunstuk (onderdeel 3) getoon.
Die linkeraansig.
* ALLE tekene moet voldoen aan die riglyne vervat in die
Ø22
SANS 10111.
LET WEL:
Ø82
* Toon DRIE vlakke van die M16-moer en ALLE nodige
110 SSD
4 konstruksies.
7 * Teken die gebruiklike voorstelling (konvensie) van die
reguittandrat volgens die SANS 10111.
6 Ø42
25
* Geen verborge besonderhede word verlang nie.
5 33
Voeg die volgende kenmerke by die tekening:
* Die snyvlak A-A
REGUITTANDRAT (4)
5 * Benoem die deursnee-aansig SNIT A-A
22 33 16
6
Ø16 A
3 Ø42 Ø28
LYS VAN ONDERDELE
ONDERDEEL HOEVEELHEID MATERIAAL
2 1 M24-MOER 1 SAGTE STAAL
1 2
3
WASTER
STEUNSTUK
1
1
VEERSTAAL
GIETYSTER
4 REGUITTANDRAT 1 SAGTE STAAL
5 BUS 2 BRONS
6 81 6 AS 1 SAGTE STAAL
6 12 41 12 15 22
7 SPY 1 SAGTE STAAL
12
7de LAAN
BLIKKIESDORP
15
VRYBURG
7
5
0084
A 117
082 345 6789
64 139
70
76
REGUITTANDRAT-SAMESTELLING
82 ALLE AFMETINGS ALLE
STEUNSTUK (3) IS IN ONGESPESIFISEERDE
UITSKUIF-ISOMETRIESE TEKENING
MILLIMETER RADIUSSE IS R3.
COPYRIGHT © JP
KOPIEREG © JP
NAAM: MEGANIESE SAMESTELLING
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
RUBRIC CORRECTNESS
OUTSTANDING
VERY GOOD
GOOD
VERY BAD
NON COMPLIANCE NC
QUALITY & NEATNESS
OUTSTANDING
VERY BAD
NON COMPLIANCE NC
TOTAL 10
A
SECTION A-A
COPYRIGHT © JP
KOPIEREG © JP
NAME: MECHANICAL ASSEMBLY
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
RUBRIEK KORREKTHEID
UITSTEKEND
BAIE GOED
GOED
BAIE SWAK
NIE VOLDOEN NV
KWALITEIT & NETHEID
UITSTEKEND
BAIE SWAK
NIE VOLDOEN NV
TOTAAL 10
A
SNIT A-A
COPYRIGHT © JP
KOPIEREG © JP
NAAM: MEGANIESE SAMESTELLING
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
72°
S
Always remember to draw an auxiliary view for any given polygon / Onthou om altyd 'n hulpaansig te teken vir enige gegewe veelhoek
Know your isometric circle construction / Ken jou isometriese sirkel konstruksie
Make S the lowest point on the drawing / Maak S die laagste punt van die tekening
A Isometric drawing is always on a 30° angle. 'n Isometriese tekening is altyd op 'n 30° hoek.
30° 30°
S
QUESTION: ISOMETRIC DRAWING
Given:
* The front view, top view and left view of a sliding jig.
* The position of point S on the drawing sheet.
Instructions:
Use scale 1 : 1 and convert the orthographic views
of the sliding-jig into an isometric drawing.
Gegee:
* Die vooraansig, bo-aansig en linkeraansig van 'n gly-setmaat.
* Die posisie van punt S op die tekenvel.
Instruksies:
Gebruik skaal 1 : 1 en omskep die ortografiese aansigte
van die gly-setmaat in 'n isometriese tekening.
40 25 25
40
20
25 S
10 10 30 40 15
15
R55
15
15
42
15
60° 60°
20 20 S S 40
80 95
NC
NC
S
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: ISOMETRIC / ISOMETRIES
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: ISOMETRIC DRAWING
Given:
* The front view, top view and left view of a casting.
* The position of point S on the drawing sheet.
Instructions:
Use scale 1 : 1 and convert the orthographic views of the
casting into an isometric drawing.
Gegee:
* Die vooraansig, bo-aansig en linkeraansig van 'n gietstuk.
* Die posisie van punt S op die tekenvel.
Instruksies:
Gebruik skaal 1 : 1 en omskep die ortografiese aansigte van die
gietstuk in 'n isometriese tekening.
124
56
14
20
48
24
40
S
R40
44
10 10
72 S S 30 30 20
NC
NC
S 10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: ISOMETRIC / ISOMETRIES
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: ISOMETRIC DRAWING
Given:
* The front view and left view of a pipe support.
* The position of point S on the drawing sheet.
Instructions:
Use scale 1 : 1 and convert the orthographic views
of the pipe support into an isometric drawing.
Gegee:
* Die vooraansig en linkeraansig van 'n pypstuk.
* Die posisie van punt S op die tekenvel.
Instruksies:
Gebruik skaal 1 : 1 en omskep die ortografiese aansigte
van die pypstuk in 'n isometriese tekening.
60
10 10 50
10
20
40
5 5 10
15
20
15
63°
10
15
80 S S 15
100
NC
NC
S 10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: ISOMETRIC / ISOMETRIES
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: ISOMETRIC DRAWING
Given:
* The front view, top view and left view of a casting.
* The position of point S on the drawing sheet.
Instructions:
Use scale 1 : 1 and convert the orthographic views of the
casting into an isometric drawing.
Gegee:
* Die vooraansig, bo-aansig en linkeraansig van 'n gietstuk.
* Die posisie van punt S op die tekenvel.
Instruksies:
Gebruik skaal 1 : 1 en omskep die ortografiese aansigte van die
gietstuk in 'n isometriese tekening.
12
30
S
70
Ø50
36 S S 140
NC
NC
S 10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: ISOMETRIC / ISOMETRIES
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: ISOMETRIC DRAWING
Given:
* The front view and top view of a rod guide.
* The position of point S on the drawing sheet.
Instructions:
Use scale 1 : 1 and convert the orthographic views of the rod
guide into an isometric drawing.
Gegee:
* Die vooraansig en bo-aansig van 'n stanggids.
* Die posisie van punt S op die tekenvel.
Instruksies:
Gebruik skaal 1 : 1 en omskep die ortografiese aansigte van die
stanggids in 'n isometriese tekening.
56
□
6
Ø40
12
24
70
10
16
S NC
25°
NC
S 10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: ISOMETRIC / ISOMETRIES
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: ISOMETRIC DRAWING
Given:
* The front view, top view and left view of a jig with
a regular hexagonal hole.
* The position of point S on the drawing sheet.
Instructions:
Use scale 1 : 1 and convert the orthographic views
of the jig into an isometric drawing.
Gegee:
* Die vooraansig, bo-aansig en linkeraansig van 'n
setmaat met 'n reëlmatige seshoekige gat.
* Die posisie van punt S op die tekenvel.
Instruksies:
Gebruik skaal 1 : 1 en omskep die ortografiese aansigte
van die setmaat in 'n isometriese tekening.
85
20
S
15
R45
34
37
20
30 30 S S 25 NC
65
NC
S
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: ISOMETRIC / ISOMETRIES
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: ISOMETRIC DRAWING
Given:
* The front view, top view en right view of a casting.
* The position of point S on the drawing sheet.
Instructions:
Use scale 1 : 1 and convert the orthographic
views of the casting into an isometric drawing.
Gegee:
* Die vooraansig, bo-aansig en regteraansig van 'n gietstuk.
* Die posisie van punt S op die tekenvel.
Instruksies:
Gebruik skaal 1 : 1 en omskep die ortografiese
aansigte van die gietstuk in 'n isometriese tekening.
25 15 80
S
15 35 35 15
40
40
32
40
S S NC
S
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: ISOMETRIC / ISOMETRIES
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: ISOMETRIC DRAWING
Given:
* The front view and top view of a casting.
* The position of point S on the drawing sheet.
Instructions:
Use scale 1 : 1 and convert the orthographic
views of the casting into an isometric drawing.
Gegee:
* Die vooraansig en bo-aansig van 'n gietstuk.
* Die posisie van punt S op die tekenvel.
Instruksies:
Gebruik skaal 1 : 1 en omskep die ortografiese
aansigte van die gietstuk in 'n isometriese tekening.
60
R30
56
15
45°
S
20
20
S
30
NC
NC
S
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: ISOMETRIC / ISOMETRIES
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: ISOMETRIC DRAWING
Given:
* The front view, top view and right view of a casting
with a cutting plane A-A.
* The position of point S on the drawing sheet.
Instructions:
Use scale 1 : 1 and convert the orthographic views of the casting
into a sectional isometric drawing on cutting plane A-A.
Gegee:
* Die vooraansig, bo-aansig en regteraansig van 'n
gietstuk met 'n snyvlak A-A.
* Die posisie van punt S op die tekenvel.
Instruksies:
Gebruik skaal 1 : 1 en omskep die ortografiese aansigte van die
gietstuk in 'n deursnee-isometriese tekening volgens snyvlak A-A.
44
22
S
22
A A
30°
20
R44
124
20
Ø30
12 12 12
90 20 S S NC
NC
S
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: ISOMETRIC / ISOMETRIES
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: ISOMETRIC DRAWING
Given:
* The front view, top view and left view of a cross slide with a
cutting plane A-A.
* The position of point S on the drawing sheet.
Instructions:
Use scale 1 : 1 and convert the orthographic views of the cross
slide into a sectional isometric drawing on cutting plane A-A.
Gegee:
* Die vooraansig, bo-aansig en linkeraansig van 'n dwarsskuif
met 'n snyvlak A-A.
* Die posisie van punt S op die tekenvel.
Instruksies:
Gebruik skaal 1 : 1 en omskep die ortografiese aansigte van die
dwarsskuif in 'n deursnee-isometriese tekening volgens snyvlak
A-A.
16
60
A A
S
10
35
45
85
15 30
15
16
60°
15
16 S S 50 NC
NC
S
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: ISOMETRIC / ISOMETRIES
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP
QUESTION: ISOMETRIC DRAWING
Given:
* The front view, top view and left view of a channel drilling jig
with a cutting plane A-A.
* The position of point S on the drawing sheet.
Instructions:
Use scale 1 : 1 and convert the orthographic views of the
channel drilling jig into a sectional isometric drawing on cutting
plane A-A.
Gegee:
* Die vooraansig, bo-aansig en linkeraansig van 'n
kanaal-boorsetmaat met 'n snyvlak A-A.
* Die posisie van punt S op die tekenvel.
Instruksies:
Gebruik skaal 1 : 1 en omskep die ortografiese aansigte van die
kanaal-boorsetmaat in 'n deursnee-isometriese tekening volgens
snyvlak A-A.
30 30 50 30
10
80
10
A A
70 S
Ø25
50
85
60
15
40 S S 140
NC
NC
S 10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: ISOMETRIC / ISOMETRIES
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
PP PP
PV PV
LVP HL HL RVP HL
GL GL
SP
QUESTION: PERSPECTIVE VRAAG: PERSPEKTIEF
Use the given information and draw a neat two-point Gebruik die gegewe inligting en teken 'n netjiese
perspective drawing of the models. tweepuntperspektieftekening van die modelle.
.
Instructions: Instruksies:
* Align the drawing sheet with the ground line (GL). * Rig die tekening volgens die grondlyn (GL).
* Locate and label the vanishing points. * Bepaal en benoem die verdwynpunte.
* Show ALL necessary construction. * Toon ALLE nodige konstruksies.
* NO hidden detail is required. * GEEN verborge besonderhede word verlang nie.
NC NC
NC NC
10 10
PP PP PP
PV PV PV
HL
HL HL
LVP RVP LVP RVP
SP
SP
GL GL
GL
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: PERSPECTIVE / PERSPEKTIEF
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: PERSPECTIVE VRAAG: PERSPEKTIEF
Use the given information and draw a neat two-point Gebruik die gegewe inligting en teken 'n netjiese
perspective drawing of the models. tweepuntperspektieftekening van die modelle.
.
Instructions: Instruksies:
* Align the drawing sheet with the ground line (GL). * Rig die tekening volgens die grondlyn (GL).
* Locate and label the vanishing points. * Bepaal en benoem die verdwynpunte.
* Show ALL necessary construction. * Toon ALLE nodige konstruksies.
* NO hidden detail is required. * GEEN verborge besonderhede word verlang nie.
NC NC
NC NC
10 10
PP PP PP
PV PV PV
HL
HL HL
LVP RVP LVP RVP
SP
SP
GL GL GL GL
GL
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: PERSPECTIVE / PERSPEKTIEF
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: PERSPECTIVE VRAAG: PERSPEKTIEF
Use the given information and draw a neat two-point Gebruik die gegewe inligting en teken 'n netjiese
perspective drawing of the model. tweepuntperspektieftekening van die model.
.
Instructions: Instruksies:
* Align the drawing sheet with the ground line (GL). * Rig die tekening volgens die grondlyn (GL).
* Locate and label the vanishing points. * Bepaal en benoem die verdwynpunte.
* Show ALL necessary construction. * Toon ALLE nodige konstruksies.
* NO hidden detail is required. * GEEN verborge besonderhede word verlang nie.
PP PP
PV PV
HL HL
LVP RVP
NC
GL GL GL
NC
SP
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: PERSPECTIVE / PERSPEKTIEF
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: PERSPECTIVE VRAAG: PERSPEKTIEF
Given: Gegee:
Three views of a dwelling and the information needed Drie aansigte van 'n woning en die inligting benodig
to draw a two-point perspective drawing. om 'n tweepuntperspektieftekening te teken.
PP - Picture plane PV - Prentvlak
HL - Horizon line HL - Horisonlyn
GL - Ground line GL - Grondlyn
SP - Station point SP - Staanpunt
Instructions: Instruksies:
Complete the perspective drawing. Voltooi die perspektieftekening.
* Align the drawing sheet with the ground line (GL). * Rig die tekening volgens die grondlyn (GL).
* Determine and label the vanishing points. * Bepaal en benoem die verdwynpunte.
* Show ALL necessary construction. * Toon ALLE nodige konstruksies.
* Show the wall thickness at the openings. * Toon die muurdikte by die openinge.
* Show the internal detail. * Toon die interne besonderhede.
* NO hidden detail is required. * GEEN verborge besonderhede word verlang nie.
PP PP
PV PV
HL LVP RVP HL
GL GL
NC
SP
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: PERSPECTIVE / PERSPEKTIEF
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: PERSPECTIVE VRAAG: PERSPEKTIEF
Given: Gegee:
Two views of a recreational area and the Twee aansigte van 'n ontspanningsarea en die
information needed to draw a inligting benodig om 'n tweepuntperspektief-
two-point perspective drawing. tekening te teken.
PP - Picture plane PV - Prentvlak
HL - Horizon line HL - Horisonlyn
GL - Ground line GL - Grondlyn
SP - Station point SP - Staanpunt
SW
Instructions: IM Instruksies:
Complete the perspective drawing. SW MIN Voltooi die perspektieftekening.
EM G P
BA OO
D L
* Align the drawing sheet with the ground line (GL). * Rig die tekening volgens die grondlyn (GL).
* Determine and label the vanishing points. * Bepaal en benoem die verdwynpunte.
* Show ALL necessary construction. ST * Toon ALLE nodige konstruksies.
* NO hidden detail is required. TR EP * GEEN verborge besonderhede word verlang nie.
AP
PP PP
PV PV
HL HL
LVP RVP
NC
SP
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: PERSPECTIVE / PERSPEKTIEF
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: PERSPECTIVE VRAAG: PERSPEKTIEF
Given: Gegee:
Two views of an entertainment area and swimming pool and the Twee aansigte van 'n ontspanningsarea en swembad en die
information needed to draw a two-point perspective drawing. inligting benodig om 'n tweepuntperspektieftekening te teken.
PP - Picture plane PV - Prentvlak
HL - Horizon line HL - Horisonlyn
GL - Ground line GL - Grondlyn
SP - Station point SP - Staanpunt
Instructions: Instruksies:
Complete the perspective drawing. Voltooi die perspektieftekening.
* Align the drawing sheet with the ground line (GL). * Rig die tekening volgens die grondlyn (GL).
* Locate and label the vanishing points. * Bepaal en benoem die verdwynpunte.
* Show ALL necessary construction. * Toon ALLE nodige konstruksies.
* NO hidden detail is required. * GEEN verborge besonderhede word verlang nie.
SWIMMING POOL
SWEMBAD
NC
NC
10
PP PP
PV PV
HL HL
RVP LVP
GL GL
SWIMMING POOL
SWEMBAD
SP
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: PERSPECTIVE / PERSPEKTIEF
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: PERSPECTIVE VRAAG: PERSPEKTIEF
Given: Gegee:
Three views of a dwelling and the information Drie aansigte van 'n woning en die inligting
needed to draw a benodig om 'n tweepuntperspektief-
two-point perspective drawing. tekening te teken.
PP - Picture plane PV - Prentvlak
HL - Horizon line HL - Horisonlyn
GL - Ground line GL - Grondlyn
SP - Station point SP - Staanpunt
Instructions: Instruksies:
Complete the perspective drawing. Voltooi die perspektieftekening.
* Align the drawing sheet with the ground line (GL). * Rig die tekening volgens die grondlyn (GL).
* Determine and label the vanishing points. * Bepaal en benoem die verdwynpunte.
* Show ALL necessary construction. * Toon ALLE nodige konstruksies.
* Show the wall thickness at the openings. * Toon die muurdikte by die openinge.
* Show the internal detail. * Toon die interne besonderhede.
* NO hidden detail is required. * GEEN verborge besonderhede word verlang nie.
PP PP
PV PV
HL HL HL RVP HL
LVP
GL GL
NC
SP
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: PERSPECTIVE / PERSPEKTIEF
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: PERSPECTIVE VRAAG: PERSPEKTIEF
Given: Gegee:
Three views of a dwelling and the information Drie aansigte van 'n woning en die inligting
needed to draw a benodig om 'n tweepuntperspektief-
two-point perspective drawing. tekening te teken.
PP - Picture plane PV - Prentvlak
HL - Horizon line HL - Horisonlyn
GL - Ground line GL - Grondlyn
SP - Station point SP - Staanpunt
Instructions: Instruksies:
Complete the perspective drawing. Voltooi die perspektieftekening.
* Align the drawing sheet with the ground line (GL). * Rig die tekening volgens die grondlyn (GL).
* Determine and label the vanishing points. * Bepaal en benoem die verdwynpunte.
* Show ALL necessary construction. * Toon ALLE nodige konstruksies.
* Show the wall thickness at the openings. * Toon die muurdikte by die openinge.
* NO hidden detail is required. * GEEN verborge besonderhede word verlang nie.
PP PP
PV PV
HL HL
LVP RVP
NC
GL GL GL GL
NC
SP 10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: PERSPECTIVE / PERSPEKTIEF
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: PERSPECTIVE VRAAG: PERSPEKTIEF
Given: Gegee:
Three views of a dwelling and the information Drie aansigte van 'n woning en die inligting
needed to draw a benodig om 'n tweepuntperspektief-
two-point perspective drawing. tekening te teken.
PP - Picture plane PV - Prentvlak
HL - Horizon line HL - Horisonlyn
GL - Ground line GL - Grondlyn
SP - Station point SP - Staanpunt
Instructions: Instruksies:
Complete the perspective drawing. Voltooi die perspektieftekening.
* Align the drawing sheet with the ground line (GL). * Rig die tekening volgens die grondlyn (GL).
* Determine and label the vanishing points. * Bepaal en benoem die verdwynpunte.
* Show ALL necessary construction. * Toon ALLE nodige konstruksies.
* Show the wall thickness at the openings. * Toon die muurdikte by die openinge.
* Show the internal detail. * Toon die interne besonderhede.
* NO hidden detail is required. * GEEN verborge besonderhede word verlang nie.
PP PP
PV PV
HL HL
RVP LVP
NC
GL GL
NC
SP
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: PERSPECTIVE / PERSPEKTIEF
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: PERSPECTIVE VRAAG: PERSPEKTIEF
Given: Gegee:
Three views of a church and the information needed Drie aansigte van 'n kerk en die inligting benodig
to draw a two-point perspective drawing. om 'n tweepuntperspektieftekening te teken.
PP - Picture plane PV - Prentvlak
HL - Horizon line HL - Horisonlyn
GL - Ground line GL - Grondlyn
SP - Station point SP - Staanpunt
Instructions: Instruksies:
Complete the perspective drawing. Voltooi die perspektieftekening.
* Align the drawing sheet with the ground line (GL). * Rig die tekening volgens die grondlyn (GL).
* Determine and label the vanishing points. * Bepaal en benoem die verdwynpunte.
* Show ALL necessary construction. * Toon ALLE nodige konstruksies.
* Show the wall thickness at the openings. * Toon die muurdikte by die openinge.
* Show the internal detail. * Toon die interne besonderhede.
* NO hidden detail is required. * GEEN verborge besonderhede word verlang nie.
PP PP
PV PV
HL RVP RVP HL
GL GL
NC
SP
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: PERSPECTIVE / PERSPEKTIEF
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: PERSPECTIVE VRAAG: PERSPEKTIEF
Given: Gegee:
Three views of a dwelling and the information Drie aansigte van 'n woning en die inligting
needed to draw a benodig om 'n tweepuntperspektief-
two-point perspective drawing. tekening te teken.
PP - Picture plane PV - Prentvlak
HL - Horizon line HL - Horisonlyn
GL - Ground line GL - Grondlyn
SP - Station point SP - Staanpunt
Instructions: Instruksies:
Complete the perspective drawing. Voltooi die perspektieftekening.
* Align the drawing sheet with the ground line (GL). * Rig die tekening volgens die grondlyn (GL).
* Determine and label the vanishing points. * Bepaal en benoem die verdwynpunte.
* Show ALL necessary construction. * Toon ALLE nodige konstruksies.
* Show the wall thickness at the openings. * Toon die muurdikte by die openinge.
* NO hidden detail is required. * GEEN verborge besonderhede word verlang nie.
NC
PP PP
PV PV
NC
10
LVP LVP
HL HL
GL GL
SP
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: PERSPECTIVE / PERSPEKTIEF
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: PERSPECTIVE VRAAG: PERSPEKTIEF
Given: Gegee:
Three views of a dwelling and the information Drie aansigte van 'n woning en die inligting
needed to draw a benodig om 'n tweepuntperspektief-
two-point perspective drawing. tekening te teken.
PP - Picture plane PV - Prentvlak
HL - Horizon line HL - Horisonlyn
GL - Ground line GL - Grondlyn
SP - Station point SP - Staanpunt
Instructions: Instruksies:
Complete the perspective drawing. Voltooi die perspektieftekening.
* Align the drawing sheet with the ground line (GL). * Rig die tekening volgens die grondlyn (GL).
* Determine and label the vanishing points. * Bepaal en benoem die verdwynpunte.
* Show ALL necessary construction. * Toon ALLE nodige konstruksies.
* Show the wall thickness at the openings. * Toon die muurdikte by die openinge.
* Show the internal detail. * Toon die interne besonderhede.
* NO hidden detail is required. * GEEN verborge besonderhede word verlang nie.
PP PP
PV PV
HL HL
LVP RVP
NC
GL GL
NC
SP 10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: PERSPECTIVE / PERSPEKTIEF
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: PERSPECTIVE VRAAG: PERSPEKTIEF
Given: Gegee:
Three views of a braai area and the information Drie aansigte van 'n braaiplek en die inligting
needed to draw a benodig om 'n tweepuntperspektief-
two-point perspective drawing. tekening te teken.
PP - Picture plane PV - Prentvlak
HL - Horizon line HL - Horisonlyn
GL - Ground line GL - Grondlyn
SP - Station point SP - Staanpunt
Instructions: Instruksies:
Complete the perspective drawing. Voltooi die perspektieftekening.
* Align the drawing sheet with the ground line (GL). * Rig die tekening volgens die grondlyn (GL).
* Determine and label the vanishing points. * Bepaal en benoem die verdwynpunte.
* Show ALL necessary construction. * Toon ALLE nodige konstruksies.
* NO hidden detail is required. * GEEN verborge besonderhede word verlang nie.
PP PP
PV PV
HL LVP RVP HL
NC
GL SP GL
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: PERSPECTIVE / PERSPEKTIEF
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: PERSPECTIVE VRAAG: PERSPEKTIEF
Given: Gegee:
Three views of a dwelling and the information Drie aansigte van 'n woning en die inligting
needed to draw a benodig om 'n tweepuntperspektief-
two-point perspective drawing. tekening te teken.
PP - Picture plane PV - Prentvlak
HL - Horizon line HL - Horisonlyn
GL - Ground line GL - Grondlyn
SP - Station point SP - Staanpunt
Instructions: Instruksies:
Complete the perspective drawing. Voltooi die perspektieftekening.
* Align the drawing sheet with the ground line (GL). * Rig die tekening volgens die grondlyn (GL).
* Determine and label the vanishing points. * Bepaal en benoem die verdwynpunte.
* Show ALL necessary construction. * Toon ALLE nodige konstruksies.
* Show the wall thickness at the openings. * Toon die muurdikte by die openinge.
* NO hidden detail is required. * GEEN verborge besonderhede word verlang nie.
PP PP
PV PV
NC
NC
10
LVP
HL HL HL
RVP
GL GL GL
SP
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: PERSPECTIVE / PERSPEKTIEF
GRADE/ GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: PERSPECTIVE VRAAG: PERSPEKTIEF
Given: Gegee:
Three views of a dwelling and the information Drie aansigte van 'n woning en die inligting
needed to draw a benodig om 'n tweepuntperspektief-
two-point perspective drawing. tekening te teken.
PP - Picture plane PV - Prentvlak
HL - Horizon line HL - Horisonlyn
GL - Ground line GL - Grondlyn
SP - Station point SP - Staanpunt
Instructions: Instruksies:
Complete the perspective drawing. Voltooi die perspektieftekening.
* Align the drawing sheet with the ground line (GL). * Rig die tekening volgens die grondlyn (GL).
* Determine and label the vanishing points. * Bepaal en benoem die verdwynpunte.
* Show ALL necessary construction. * Toon ALLE nodige konstruksies.
* Show the wall thickness at the openings. * Toon die muurdikte by die openinge.
* Show the internal detail. * Toon die interne besonderhede.
* NO hidden detail is required. * GEEN verborge besonderhede word verlang nie.
PP PP
PV PV
NC
NC
HL LVP RVP HL 10
GL GL GL
SP
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: PERSPECTIVE / PERSPEKTIEF
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
ERF 27 ERF 2
32,5 D 72000 44000 30,0 A
5000 BL
RYLAAN
AFGEWERK ERF 3
MET SO
IO ONTSPANNINGS-
KEISTENE
5000 BL
IO AREA
10
IO
IO
NUWE
0
00
9
16
INHEEMSE SO
BOME ST 3
5000 BL
SO
IO
IO
STRELITZIARYLAAN
3 SO
PROTEARYLAAN
IO
IO
IO
IO 8
121000
3000 4 IO
SO
ST 2 IO
0
0
00
00
7
16
16
SO
ST 4
SO SO
2,3m HOË IO IO
IO IO
METAAL- 2 5
PALISSADE-
IO IO
VEILIGHEIDS- IO IO
HEINING
1 6
SO SO
ST 1 ST 5
STOP
VEILIGHEIDS- ST
19000
BEHEERGEBOU
18076
STOP
5000 BL
STOP 35,2 C 34,5 B STOP
HOOFSTRAAT
STOP ELEKTRIESE ALLE SEPTIESE TENKS STOP
TOEVOER MOET VOLGENS
ET 35 INGENIEURS-
GRENSLENGTES SPESIFIKASIES GEBOU
AB = CD WORD
AD = BC
FEATURE TRUE EXAMPLE COMPUTER SYMBOL (CAD) VIEW ON PLAN VIEW ON ELEVATION
EIENSKAP WARE VOORBEELD REKENAARSIMBOOL (ROT) AANSIG OP PLAN AANSIG OP ELEVASIE
BATH (B)
BAD (B)
BIDET (BT)
WASH-BASIN (WB)
(HAND)
HANDWASBAK (WB)
WASH TUB (WT)
(WASH TROUGH)
WASTROG (WT)
WATER-CLOSET (WC)
(TOILET)
SPOELKLOSET (SK)
(TOILET)
SHOWER (SH)
STORT (ST)
SINK (S)
(SINGLE)
OPWASBAK (OWB)
(ENKEL)
SINK (S)
(DOUBLE)
OPWASBAK (OWB)
(DUBBEL)
URINAL (U)
(SLAB / STALL TYPE)
URINAAL (U)
(BLOK / STAL TIPE)
URINAL (U)
(WALL MOUNTED
TYPE)
URINAAL (U)
(MUUR-
GEMONTEERDE
TIPE)
COPYRIGHT © JP
KOPIEREG © JP
QUESTION: ANALYTICAL (CIVIL)
NOTE:
Contractors must verify all dimensions and
levels on site before commencing work.
Given:
LAND SURVEYOR'S CERTIFICATE OF THE Architects to be immediately notified of any
BOUNDARY LENGTHS AND CORNER discrepancies. The site plan of a proposed new dwelling with a swimming pool, a title panel and a table of questions. The
HEIGHTS OF STAND 33 AT drawing has not been prepared to the indicated scale.
24 POINTSETTA STREET SINOVILLE 20. In the space below, draw, in
SURVEYED ON 19-10-2013
neat freehand, the front view Instructions:
LENGTHS IN HEIGHTS IN and top view of the SANS Complete the table below by neatly answering the questions, which all refer to the accompanying
METRES METRES
10143 graphical symbol drawing and title panel. [30]
AB = 40, 500 A = 434 (convention) of a TOILET.
BC = 26, 200 B = 437 QUESTIONS ANSWERS
CD = 34, 500 C = 436 ANSWER 20. 1 Which company did the printing of the site plan? SPEKTRUM 1
DE = 8, 485 D = 434
2 On what date was the site surveyed? 19/10/2013 1
EA = 20, 200 E = 432
3 Which corner is the lowest corner on STAND 33? E / 432 1
POINTSETTA STREET
7 Name the feature at 3. GULLEY 1
432 434 FEATURE 1
8 Name the feature at 4. WATER-STORAGE TANK 1
E A
9 Name the feature at 5. WATER METER 1
1
5000 BL MH 1:40
ARCHITECT'S SIGNATURE.................................................... 10 What is the fall of the sewerage line? 1
434 D CLIENT'S SIGNATURE............................................................
STAND 33 STAND 34 11 How deep is the municipal sewerage connection in metres? 1,2 m 1
2
9000
12 Why would the municipality rejecte the plan? POOL OVER THE BUILDING LINE 1
3000 BL
DRIVEWAY
13 Which elevation of the new dwelling faces Pointsetta Street? NORTH EAST 2
RWDP RWDP
3 1 2013-10-28
MOVE
Sewer line BROWN 1
RUSPOLIA STREET
POOL
W
REVISION DATE DESCRIPTION In which colours could the Concrete GREEN 1
3500 2304 3929
GARAGE
COPYRIGHT © JP
KOPIEREG © JP
NAME: ANALYTICAL (CIVIL)
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
NOTA: VRAAG: ANALITIES (SIVIEL)
Kontrakteurs moet alle afmetings en hoogtes
op die terrein nagaan voordat daar met enige
LANDMETERSERTIFIKAAT VAN DIE werk begin word. Argitekte moet onmiddellik Gegee:
GRENSLENGTES EN HOEKHOOGTES van enige teenstrydighede in kennis gestel Die terreinplan van 'n voorgestelde nuwe woning met 'n swembad, 'n titelpaneel en 'n tabel met vrae. Die
word.
VAN ERF 33 TE POINTSETTASTRAAT 24 tekening is nie volgens die aangetoonde skaal voorberei nie.
SINOVILLE
OPGEMEET OP 19-10-2013
Instruksies:
LENGTES IN HOOGTES IN Voltooi die tabel hieronder deur die vrae, wat almal na die bygaande tekening en titelpaneel verwys,
METER METER
netjies te beantwoord. [30]
AB = 40, 500 A = 434
POINTSETTASTRAAT
7 Benoem die kenmerk by 3. RIOOLPUT 1
432 434 KENMERK 1
8 Benoem die kenmerk by 4. WATEROPGAARTENK 1
E A
9 Benoem die kenmerk by 5. WATERMETER 1
1
5000 BL MG 1:40
ARGITEK SE HANDTEKENING.............................................. 10 Wat is die val van die rioollyn? 1
434 D KLIËNT SE HANDTEKENING.................................................
ERF 33 ERF 34 11 Hoe diep is die munisipale rioolaansluiting in meter? 1,2 m 1
2
9000
12 Waarom sou die munisipaliteit die plan afgekeur? SWEMBAD IS OOR DIE BOULYN 1
3000 BL
OPRIT
SWEMBAD
W
HERSIENING DATUM BESKRYWING In watter kleure kan die volgende Beton GROEN 1
MOTORHUIS
COPYRIGHT © JP
KOPIEREG © JP
NAAM: ANALITIES (SIVIEL)
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
STAND 396 QUESTION: ANALYTICAL (CIVIL)
2431
1
1432 1430 Given:
30000
The site plan of a proposed new dwelling and a table of questions.
2
NOTE: 3000 BL Instructions:
THE SEPTIC TANK (S/T) Complete the table below by neatly answering the questions, which all refer to the accompanying
TO BE BUILT TO
3 drawing. [30]
S/T
ENGINEER'S
G
SPECIFICATIONS
RE
IE 4 QUESTIONS ANSWERS
STAND
3000 BL
405
1 What does the abbreviation NTS stand for? NOT TO SCALE 1
5 2 How many complete stands are shown on the site plan? 1 1
RWDP
3 What is the name of the street? BABIANA STREET 1
IE
NEW DWELLING 6 6 Name the feature at 3. SEPTIC TANK 1
37500
NEW DRIVEWAY
407 ELECTRICITY METER
W 10 Name the feature at 7. (WATT RECORDING)
1
ANSWER 22. (VIEW IN PLAN) ANSWER 22. (VIEW IN ELEVATION) If the total area of the new dwelling is 209,86 m² and the total = 209.86 / 1125
21 the total area of the stand is 1125 m², determine the = 0,1865 x 100 3
= 18,65%
percentage of the stand that is covered by the new dwelling. = CALCULATION 1, ANSWER 2
In the space provided in the title panel, draw, in neat freehand, the plan and elevation view of the
22 4
SANS 10143-graphic symbol of a wall mounted urinal.
TOTAL 30
COPYRIGHT © JP
KOPIEREG © JP
NAME: ANALYTICAL (CIVIL)
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
ERF 396 VRAAG: ANALITIES (SIVIEL)
2431
1
1432 1430 Gegee:
30000
Die terreinplan van 'n voorgestelde nuwe woning en 'n tabel met vrae.
2
LET WEL: 3000 BL Instruksies:
DIE SEPTIESE TENK (S/T) Voltooi die tabel hieronder deur die vrae, wat almal na die bygaande tekening verwys, netjies te
MOET VOLGENS 3 beantwoord. [30]
INGENIEURS- S/T
SPESIFIKASIES GEBOU RP
WORD SO
IO 4 VRAE ANTWOORDE
ERF
3000 BL
405
1 Waarvoor staan die afkorting NVS? NIE VOLGENS SKAAL 1
5 2 Hoeveel volledige erwe word daar op die terreinplan getoon? 1 1
RWAP
3 In watter straat is die erf? BABIANASTRAAT 1
IO
NUWE WONING 6 6 Benoem die kenmerk by 3. SEPTIESE-TENK 1
37500
407 ELEKTRIESE METER
W 10 Benoem die kenmerk by 7. 1
NUWE OPRIT
(WATT-METERLESING)
11 Benoem die lyn by 8. BOULYN 1
7500 BL 8
12 Benoem die kenmerk by 9. BOOM 1
ANTWOORD 22. (AANSIG OP PLAN) ANTWOORD 22. (AANSIG OP ELEVASIE) Indien die totale oppervlakte van die nuwe woning 209,86 m² = 209.86 / 1125
is en die totale oppervlakte van die erf 1125 m² is, bepaal die = 0,1865 x 100
21 3
persentasie van die erf wat deur die nuwe woning beslaan = 18,65%
word. = BEREKENING 1, ANTW 2
In die spasie voorsien in die titelpaneel, teken, in netjiese vryhand, die plan- en elevasie-aansig
22 4
van die SANS 10143-grafiesesimbool vir 'n muurgemonteerde urinaal.
TOTAAL 30
COPYRIGHT © JP
KOPIEREG © JP
NAAM: ANALITIES (SIVIEL)
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
NOTE:
Contractors must verify all dimensions and levels
on site before commencing work. Architects to be
LAND SURVEYOR'S CERTIFICATE OF THE notified immediately of any discrepancies.
BOUNDARY LENGTHS AND CORNER
HEIGHTS OF STAND 77 AT
ARCHITECT'S SIGNATURE...............................
93 JAMES DRIVE SINOVILLE
SURVEYED ON 17-09-2014 CLIENT'S SIGNATURE......................................
BOUNDARY LENGTHS CORNER HEIGHTS
IN MILLIMETRES IN METRES
AB = 42688 A = 1022
BC = 31684 B = 1024
QUESTIONS ANSWERS
CD = 42688 C = 1025 1 On what date was the stand surveyed? 17-09-2014 1
DA = 31684 D = 1021 2 What was Fourie responsible for? CHECKING THE DRAWING 1
3 How wide is the pavement on James Drive in metres? 3m 1
4 What is the client's name? A DU PLOOY 1
NEW SEWER MUNICIPAL CONNECTION
2,5 m DEEP 5 How many new parking bays are indicated? 6 1
STAND 34 1
6 How many new inspection eyes are required? 4 1
MAIN MUNICIPAL SEWER LINE
B C 7 On which property is the municipal sewer connection located? STAND 34 1
1500 BL
8 In what colour is a new building presented on a site plan? RED 1
5018
IE IE
RE
STAND 78 STAND 77 STAND 76
9 In what colour is a new sewer line presented on a site plan? BROWN 1
1500 BL
2
10 What does the arrow at 1 indicate? DIRECTION OF FLOW 1
EXISTING SEWER LINE
driveway
NEW
RE 18 4
metres. Show ALL calculations.
1500 BL
20 front view and top view of the SANS 10143 graphic symbols for a 3
A D SPEKTRUM 2014-09-25
single kitchen sink.
3000
DRAWING TITLE
PAVEMENT PAVEMENT
SITE PLAN TOTAL 30
EXISTING
NEW 3.3 m
3.3 m PROJECT
ANSWER 18. 13200 8300 ANSWER 19.
MOTOR
6000
MOTOR
ENTRANCE PROPOSED NEW OFFICE Show ALL calculations. Show ALL calculations.
ENTRANCE JAMES DRIVE FOR A DU PLOOY ON STAND 77
93 JAMES DRIVE, = [2(24.7) + 2(16.5) + 2(10.2)] = (24,7 x 16.5) - (10.2 x 3.2)
10200
NEW
SINOVILLE, PRETORIA, 0182 = 102,8 m OFFICE = 374,91 m²
16500
SITE PLAN PROJECT NUMBER DRAWING NUMBER
COPYRIGHT © JP
KOPIEREG © JP
NAME: ANALYTICAL (CIVIL)
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
LET WEL:
Kontrakteurs moet alle afmetings en hoogtes op
die terrein bevestig voordat daar met werk begin
word. Argitekte moet onmiddellik in kennis gestel
LANDMETERSERTIFIKAAT VIR DIE word van enige afwykings.
GRENSLENGTES EN HOEKHOOGTES
VIR ERF 77 BY JAMESRYLAAN 93
SINOVILLE ARGITEK SE HANDTEKENING.........................
OPGEMEET OP 17-09-2014 KLIËNT SE HANDTEKENING ..........................
GRENSLENGTES IN HOEKHOOGTES IN
MILLIMETER METER
AB = 42688 A = 1022
BC = 31684 B = 1024
VRAE ANTWOORDE
CD = 42688 C = 1025 1 Op watter datum is die erf opgemeet? 17-09-2014 1
DA = 31684 D = 1021 2 Waarvoor was Fourie verantwoordelik? NASIEN VAN DIE TEKENING 1
3 Hoe wyd is die sypaadjie in Jamesrylaan in meter? 3m 1
4 Wat is die kliënt se naam? A DU PLOOY 1
NUWE RIOOLYN MUNISIPALE VERBINDING
2,5 m DIEP 5 Hoeveel nuwe parkeerplekke word aangetoon? 6 1
ERF 34 1
6 Hoeveel nuwe inspeksie-oë word benodig? 4 1
HOOF MUNISIPALE RIOOLLYN
B C 7 Op watter perseel is die munisipale rioolaansluiting geleë? ERF 34 1
1500 BL In watter kleur moet nuwe bouwerk op 'n terreinplan aangetoon
8 ROOI 1
5018
IO IO word?
SO
ERF 78 ERF 77 ERF 76
In watter kleur moet 'n nuwe rioollyn op 'n terreinplan aangetoon
9 BRUIN 1
1500 BL
word?
2
10 Wat dui die pyl by 1 aan? VLOEI RIGTING 1
BESTAANDE RIOOLLYN
3218 13 Wat word deur die lyn by 4 aangedui? VERWYDER / BREEK AF / SLOOP 1
IO
3 3 2014-09-22 Verwyder ou oprit 14 Wat moet met die bestaande gebou op die erf gedoen word? VERWYDER / BREEK AF / SLOOP 1
IO
NUWE
OPRIT
SO 18 4
meter. Toon ALLE berekeninge.
OPRIT
1500 BL
TEKENINGTITEL
SYPAADJIE SYPAADJIE
TERREINPLAN TOTAAL 30
BESTAANDE
NUWE 3.3 m PROJEK
13200 8300
3.3 m ANTWOORD 18. ANTWOORD 19.
6000
10200
NUWE
SINOVILLE, PRETORIA, 0182 = 102,8 m KANTOOR = 374,91 m²
16500
TERREINPLAN PROJEKNOMMER TEKENINGNOMMER
COPYRIGHT © JP
KOPIEREG © JP
NAAM: ANALITIES (SIVIEL)
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
NOTE:
Contractors must verify all dimensions and QUESTION: ANALYTICAL (CIVIL)
LAND SURVEYOR'S CERTIFICATE OF THE levels on site before commencing work.
SIDE LENGTHS AND CORNER HEIGHTS Architects to be immediately notified of any Given:
OF STAND 82 AT 24 KEMPEN STREET discrepancies.
WESTSIDE
The site plan of a proposed new dwelling with a title block and a
SURVEYED ON 22-05-2009 table of questions.
LENGTHS IN HEIGHTS IN
MILLIMETRE METRES 19. In the space below, draw, in neat Instructions:
freehand, the front view and top Complete the table below by neatly printing the answers to the
AB = 16 400 A = 257,5 questions which all refer to the accompanying drawings and title
view of the SANS 10143 graphical
BC = 11 900 B = 256,9 symbol (convention) for a block. [30]
CD = 3 500 C = 256,3
wash basin.
QUESTIONS ANSWERS
DE = 8 700 D = 255,8
What is the name of the architectural firm responsible for
EF = 19 900 E = 255,2 1
designing the dwelling?
GLEN & SONS 1
FA = 20 600 F = 256,4 2 What scale is indicated for the drawing? 1:200 1
3 What is the reference code for the drawing? JPEGD-B-2011 1
NEW DWELLING IE
STAND 11 What is the street address of the new dwelling? 24 KEMPEN STREET 1
108
IE
3 12 What is the stand number to the northeast of the stand 82? STAND 83 2
STAND
13 How far is the new dwelling from the southwestern boundary line? 4500 / 4,5m 2
REVISION DATE DESCRIPTION
82 14 What is the depth of the municipal sewerage connection? 1,7 m 2
8900 256
IE C D 15 Determine the total area of the stand in square metres. 368,29 m² 3
7th AVENUE
3,5 m MOTOR-
RE WESTSIDE 16 What colour must all new glass be on presentation drawings? BLACK 2
4
ENTRANCE Tel: 031 709 8943
GARAGE 109
DKW 10-08-2010 17
presentation drawings?
RED 1
3m BL
DRAWING TITLE
4500
2m BL 5 SITE PLAN If the total area of the new dwelling is 125 m², determine the
18
percentage of the stand that is covered by the new dwelling.
33,9% 3
PROJECT
STAND
81 ON STAND 82 AT 24 KEMPEN 19 the front view and top view of the SANS 10143 graphical symbol Space provided 4
STREET WESTSIDE (convention) for a wash basin.
COPYRIGHT © JP
KOPIEREG © JP
NAME: ANALYTICAL (CIVIL)
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
NOTA:
Kontrakteurs moet alle afmetings en hoogtes VRAAG: ANALITIES (SIVIEL)
LANDMETERSERTIFIKAAT VAN DIE op die terrein nagaan voordat daar met enige
SY-AFMETINGS EN HOEKHOOGTES VAN werk begin word. Argitekte moet onmiddellik Gegee:
ERF 82 TE KEMPENSTRAAT 24 van enige teenstrydighede in kennis gestel
WESTSIDE
Die terreinplan van 'n voorgestelde nuwe woning met 'n titelblok
word.
OPGEMEET OP 22-O5-2009 en 'n tabel met nuwe vrae.
LENGTES IN HOOGTES IN
MILLIMETER METER 19. Teken, in die spasie hieronder, in Instruksies:
netjiese vryhand, die vooraansig Voltooi die tabel hieronder deur die antwoorde van die vrae, wat
AB = 16 400 A = 257,5 almal na die bygaande tekeninge en titelblok verwys, netjies te
en die bo-aansig van SANS
BC = 11 900 B = 256,9 10143 grafiese simbool drukskryf. [30]
CD = 3 500 C = 256,3
(konvensie) vir 'n wasbak.
VRAE ANTWOORDE
DE = 8 700 D = 255,8
Wat is die naam van die argiteksfirma wat verantwoordelik is vir die
EF = 19 900 E = 255,2 1
ontwerp van die woning?
GLEN & SEUNS 1
FA = 20 600 F = 256,4 2 Watter skaal is vir die tekening aangetoon? 1:200 1
3 Wat is die verwysingskode vir die tekening? JPEGD-B-2011 1
IO 10 Wat moet met die bestaande motorhuis gemerk 5 gebeur? MOET AFGEBREEK WORD
GRENSMUUR
NUWE WONING IO
ERF 11 Wat is die straatadres van die nuwe woning? KEMPENSTRAAT 24 1
108
IO
3 12 Wat is die erfnommer aan die noordoostekant van erf 82? ERF 83 2
13 Hoe ver is die nuwe woning vanaf die suidwestelike grenslyn? 4500 / 4,5m 2
ERF
HERSIENING DATUM BESRYWING
8900
82 14 Wat is die diepte van die munisipale rioolaansluiting? 1,7 m 2
256
IO C D 15 Bepaal die totale area van die erf in vierkante meter. 368,29 m² 3
SO
7de LAAN Watter kleur moet alle nuwe glas op aansigte van
3,5 m MOTOR- WESTSIDE 16
voorleggingstekeninge wees?
SWART 2
4
INGANG Tel: 031 709 8943
MOTORHUIS 109
DKW 10-08-2010 17
voorleggingstekeninge wees?
ROOI 1
3m BL
TEKENINGTITEL
4500
2m BL 5 TERREINPLAN Indien die totale area van die nuwe woning 125 m² is, bepaal die
18
persentasie van die erf wat deur die nuwe woning beslaan word.
33,9% 3
PROJEK
ERF
81 OP ERF 82 TE KEMPEN- 19 vryhand, die vooraansig en die boaansig van die SANS 10143 grafiese Spasie voorsien. 4
STRAAT 24 WESTSIDE simbool (konvensies) vir 'n wasbak.
COPYRIGHT © JP
KOPIEREG © JP
NAAM: ANALITIES (SIVIEL)
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
QUESTION: ANALYTICAL (CIVIL)
Given:
THE SITE PLAN SHOWS STAND 80
SITUATED AT KAYSERS BEACH The site plan of a proposed new dwelling and outbuilding and a
SURVEYED ON 05/08/2012 table of questions. The drawing is not to scale.
LAND SURVEYOR'S CERTIFICATE
LENGTHS IN MILLIMETRES
Instructions:
AB = 37 806
Complete the table below by neatly answering the questions,
BC = 24 200
which all refer to the accompanying drawings.
CD = 10 615
[30]
DE = 30 300
EA = 31 706 QUESTIONS ANSWERS
Why would the site plan for the new dwelling and outbuilding
1 THE OUTBUILDING IS OUTSIDE THE BUILDING LINE OR
2
not be approved by the municipality? THE OUTBUILDING ROOF IS OVER THE BOUNDARY LINE
31
2 Which stand is to the west of stand 80? STAND 79 1
31,5
3 How many complete stands are shown on the site plan? 1 1
4
4 What scale is indicated for the drawing? SCALE 1:200 1
STAND 81
5 On what date was the site surveyed? 05/08/2012 1
MARLIN DRIVE
A B
PROPOSED NEW
3000 BL
9 What does the abbreviation IE stand for? INSPECTION EYE 1
5000 BL
31
RE
10 Name the feature at 1. MAN HOLE 1
14000
IE 13 Name the feature at 4. CONTOUR LINE 1
2 ROOF OVERHANG
14 What does the line at 5 indicate? 1
DRIVEWAY
32
15 What does the line at 6 indicate? BOUNDARY LINE 1
MH
17 14 m 2
line on Marlin Drive to the new building?
32,5
STAND 79 STAND 80 32,5
Determine, in metres, the difference in height between corner B
E D 18 0,5 m 2
and corner C of the stand.
The side of the new dwelling that faces Kingfisher Drive will be
19 SOUTH 1
KINGFISHER DRIVE 7 called the ____________elevation.
Determine the perimeter of the stand in metres. 37,806 + 24,200 + 10,615 + 30,300
20 2½
Show ALL calculations. + 31,706= 134,627m
SITE PLAN 37,806 x 31,706 = 11986,67704
SCALE 1:200 Determine the total area of the stand in square metres.
37,806 - 30,3 = 7,506
21 7,506 x 7,506 = 56,340036 4½
Show ALL calculations. 56,340036 / 2 = 28,170018
1198,67704 - 28,170018 =1170,5m²
TOTAL 30
COPYRIGHT © JP
KOPIEREG © JP
NAME: ANALYTICAL (CIVIL)
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
VRAAG: ANALITIES (SIVIEL)
Gegee:
DIE TERREINPLAN TOON ERF 80
Die terreinplan van 'n voorgestelde nuwe woning en buitegebou
GELEË TE KAYSERSSTRAND en 'n tabel met vrae. Die tekening is nie volgens skaal nie.
OPGEMEET OP 05/08/2012
LANDMETERSERTIFIKAAT
ERF 81
5 Op watter datum is die terreinplan opgemeet? 05/08/2012 1
MARLINRYLAAN
A B
BUITEGEBOU
5000 BL
31
SO
10 Benoem die kenmerk by 1. MANGAT 1
14000
IO 13 Benoem die kenmerk by 4? KONTOERLYN 1
2
14 Wat word deur die lyn by 5 aangedui? DAKOORHANG 1
OPRIT
32
15 Wat word deur die lyn by 6 aangedui? GRENSLYN 1
MG
17 14 meter 2
Marlinrylaan tot by die nuwe woning?
32,5
ERF 79 ERF 80 32,5
Bepaal, in meter, die verskil in hoogte tussen hoek B en hoek C
E D 18 0,5 meter 2
van die erf.
Die kant van die woning wat na Kingfisherrylaan front, sal die
19 SUID 1
KINGFISHERRYLAAN 7 ____________aansig genoem word.
Bepaal die omtrek van die erf in meter. 37,806 + 24,200 + 10,615 + 30,300
20 2½
Toon ALLE berekeninge. + 31,706= 134,627m
TERREINPLAN 37,806 x 31,706 = 11986,67704
SKAAL 1:200 Bepaal die totale oppervlakte van die erf in vierkante meter.
37,806 - 30,3 = 7,506
21 7,506 x 7,506 = 56,340036 4½
Toon ALLE berekeninge. 56,340036 / 2 = 28,170018
1198,67704 - 28,170018 =1170,5m²
TOTAAL 30
COPYRIGHT © JP
KOPIEREG © JP
NAAM: ANALITIES (SIVIEL)
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
3
SKOORSTEEN
3
BETON DAKTEËLS
100 Ø LP
100 Ø LP
5
TG TG TG
400 SIERSTEEN
NGV VOETLYS
4 7
6
RWAP
ND7 RWAP
BEDIENDE
MG2 MG1
AGTERPLAAS KWARTIERE
2 Teëls
ND7
Teëls
N
51 ND54 NG9 D
RWAP
RWAP
D 51
N
WC
IO Teëls
SLAAPKAMER 3 RP
BIC
Mat ND4 N
D
1
1
ND7
RWAP ND RWAP
IO
RP
ND7
IO MOTORHUIS
W Grano
ND7
ND57 ND57 F
200 BW NA
B U.S. VAN TEËLS
ND7
RWAP
RWAP
SLAAPKAMER 2
ND54 NG9
ND512
Mat EETKAMER
Teëls
TV WOONKAMER SO1
Teëls LAAIKAS
arch
IO BIC
RP
MES
ND7
Teëls INGANGS-
SO2 INGANG PORTAAL
Teëls NG1
Teëls
3 500 OPVOUDEUR
100 Ø BIC ND51 ND51
W.C.
VP Teëls
ND51
Boog
AANTREK
Mat
1200 DEURE
BIC
BIC
BRAAI
ONDERDAK
STOEP
ND54 NG9
Boog Teëls WOONKAMER
KAGEL
Teëls
1
RWAP
SLAAPKAMER 1
Mat N
D
51 51
D
N
ND54 NG9
RWAP
RWAP
OOP BINNEHOF
Teëls
N
D
51 51
D
N
1200 DEURE
VOORGESTELDE
SWEMBAD
COPYRIGHT © JP
KOPIEREG © JP
NAME / NAAM: ENGINEERING GRAPHICS & DESIGN NOTES / NOTAS:
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: CIVIL DRAWING A DETAILED SECTION OF A WINDOW UP TO CEILING HEIGHT
'N GEDETAILLEERDE SNIT VAN 'N VENSTER TOT OP PLAFONHOOGTE
Given:
* An isometric drawing of a partial section of foundation
and wall detail up to ceiling height
* The partial floor plan, drawn to scale 1 : 20
Instructions:
* Draw to scale 1 : 20 a partial section elevation on
cutting plane A-A.
* ALL drawings must comply with the guidelines
contained in the SANS 10143.
Show the following features on the drawing:
* The complete foundation and exernal wall detail up
to ceiling height with the wall plate
* Window detail, with a DOUBLE lintel
* ALL hatching detail
* 170 x 35 fibre cement sill under ALL windows
* Using the correct abbreviations, label the following
features: natural grond level, finished floor level and
damp-proof course.
NOTE:
ALL substructure hatching may be drawn in freehand.
W
MU AL L
UR PLA
PL TE
AA - 1
T - 14
11 x 3
4x 8
38
DPC
VWL
LIN
TE
L/
LA
TE
I
FFL / VVV
DPC
VWL
W
NGL VE IND
NS OW
NGV TE S
RB ILL
AN
K
DPC
85
VWL
A
SCREED
25 mm
GIDSPLEISTER
VV
SECTION A-A / DEURSNEE A-A FF
L /V
A A A
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: CIVIL DRAWING / SIVIELE TEKENING
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: CIVIL DRAWING A SECTIONAL VIEW OF A DOOR WITH A WOODEN DOOR FRAME A SECTIONAL VIEW OF A DOOR WITH A METAL DOOR FRAME VRAAG: SIVIELE TEKENING
Given: 'N DEURSNEE-AANSIG VAN 'N DEUR MET 'N HOUTDEURRAAM 'N DEURSNEE-AANSIG VAN 'N DEUR MET 'N METAALDEURRAAM Gegee:
* An isometric drawing of a partial section of a * 'n Isometriese tekening van 'n gedeeltelike snit van
foundation and wall detail up to ceiling height 135
'n fondasie- en muurbesonderhede tot op plafon-
262
* Door frame profile hoogte
* The partial floor plan, drawn to scale 1 : 20 * Deurraamprofiel
28
* Die gedeeltelike vloerplan, geteken volgens
55
67
Instructions: skaal 1 : 20
12
45 45 172 45
* Draw to scale 1 : 20 a front view of a partial section
of the foundation and wall detail up to ceiling height. Instruksies:
* ALL drawings must comply with the guidelines * Teken volgens skaal 1 : 20 'n vooraansig van die
WOODEN DOOR FRAME METAL DOOR FRAME PROFILE
contained in the SANS 10143. PROFILE WITH DOUBLE REBATE
gedeeltelike snitfondasie- en muurbesonderhede
Add the following features on the drawing: tot op plafonhoogte met die muurplaat.
* Door detail, with a DOUBLE lintel HOUTDEURRAAM- METAALDEURRAAMPROFIEL * ALLE tekene moet voldoen aan die riglyne vervat
PROFIEL MET DUBBEL SPONNING
* ALL hatching detail in die SANS 10143.
* Using the correct abbreviations, label the following Voeg die volgende kenmerke op die tekening:
features: natural grond level, finished floor level and * Die deurbesonderhede, met 'n DUBBEL latei
damp-proof course. * ALLE arseringbesonderhede
* Gebruik die korrekte afkortings en benoem die
NOTE: volgende kenmerke: natuurlike grondvlak, voltooide
ALL substructure hatching may be drawn in freehand. vloervlak en vogweerlaag.
LET WEL:
ALLE substruktuurarsering mag in vryhand geteken
word.
W
MU ALL
UR PLA
W PL TE
MU ALL AA - 1
UR PLA T - 14
PL TE 11 x 3
AA - 1 4x 8
T - 14 38
11 x 3
4x 8
38
A A
SCREED SECTION A-A / DEURSNEE A-A SECTION A-A / DEURSNEE A-A SCREED
25 mm
25 mm
GIDSPLEISTER GIDSPLEISTER
V VV
VV /V
L/ FF
L
FF
NC
SCALE 1 : 20 FLOOR PLAN SCALE 1 : 20 FLOOR PLAN
A SKAAL 1 : 20 VLOERPLAN SKAAL 1 : 20 VLOERPLAN A
A A A A NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: CIVIL DRAWING / SIVIELE TEKENING
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
WINDOW SCHEDULE QUESTION: CIVIL DRAWING
1000
Given:
* The partial and incomplete floor plan of a single bedroom
showing the walls, the position of the window and door
* Incomplete foundation and wall detail
* A window schedule
* A table of fixtures
* The incomplete floor plan of the single bedroom, drawn to scale
1 : 25
HINGED HINGED
1200
SIDE SIDE
Instructions:
* Using the given incomplete view, draw, to scale 1 : 25 and in
first-angle orthographic projection the following views of the single
bedroom:
1. The complete partial floor plan
2. The complete sectional elevation on cutting plane A-A
* ALL drawings must comply with the guidelines and graphic
50 50 symbols contained in the SANS 10143.
DPC
WINDOW SPECIFICATIONS:
NOTE: 170 x 35 FIBRE CEMENT SILL UNDER THE WINDOW THE FLOOR PLAN
Add the following features to the drawing:
FIXTURES * The window (in the middle of the opening)
* A built-in cupboard at the back of the door
* ALL hatching detail
FFL THE SECTIONAL ELEVATION
DPC Add the following features on the drawing:
600
2700
BIC
34
46
45
WINDOW OPENING
85
FLOOR LEVEL NV NV
550
450
BEDROOM
CARPET
550
250
250
450 650
A A
INCOMPLETE FOUNDATION INCOMPLETE FOUNDATION FLOOR PLAN
NV NV
AND INTERNAL WALL DETAIL AND EXTERNAL WALL DETAIL SCALE 1 : 25
TOTAL 10
COPYRIGHT © JP
KOPIEREG © JP
NAME: CIVIL DRAWING
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
VENSTERSKEDULE VRAAG: SIVIELE TEKENING
1000
Gegee:
* Die gedeeltelike en onvolledige vloerplan van 'n enkel slaapkamer
wat die mure, die posisie van die venster en deur toon
* Onvolledige fondasie- en muurbesonderhede
* 'n Vensterskedule
* 'n Tabel van toebehore
* Die onvolledige vloerplan van die enkel slaapkamer, geteken
volgens skaal 1 : 25
SKARNIER- SKARNIER-
1200
KANT KANT
Instruksies:
* Gebruik die gegewe onvolledige aansig en teken, volgens
skaal 1 : 25 en in eerstehoekse ortografiese projeksie, die
volgende aansigte van die enkel slaapkamer:
1. Die volledige gedeeltelike vloerplan
2. Die volledige deursnee-aansig volgens snyvlak A-A
* ALLE tekene moet voldoen aan die riglyne en grafiese simbole
50 50 vervat in die SANS 10143.
VWL
VENSTER SPESIFIKASIES:
LET WEL: 170 x 35 VESELSEMENT-VENSTERBANK ONDER DIE VENSTER DIE VLOERPLAN
Voeg die volgende kenmerke by die tekening:
TOEBEHORE * Die venster (in die middel van die opening)
* 'n Ingeboude kas agter die deur
* ALLE arseringsbesonderhede
VVV DIE DEURSNEE-AANSIG
VWL Voeg die volgende kenmerke op die tekening:
600
2700
HOUTDEURRAAMPROFIEL
135
2100
IGK
34
46
45
VENSTEROPENING
85
GRONDVLAK NV NV
550
450
SLAAPKAMER
MAT
550
250
250
450 650
A A
ONVOLLEDIGE FONDASIE- EN ONVOLLEDIGE FONDASIE- EN VLOERPLAN
NV NV
BINNEMUURBESONDERHEDE BUITEMUURBESONDERHEDE SKAAL 1 : 25
TOTAAL 10
COPYRIGHT © JP
KOPIEREG © JP
NAAM: SIVIELE TEKENING
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
WINDOW SCHEDULE EQUAL EQUAL QUESTION: CIVIL DRAWING
1000 530 c/c 530 c/c 530 c/c 530 c/c
Given:
WINDOW NOTE: 38 x 38 mm CEILING NOTES:
* The incomplete sectional elevation A-A of a bathroom, showing
114 x 38 mm 9 mm
A = OPENING SIDE
WALL PLATE
BRANDERING
CEILING BOARD 114 x 38 mm WALL PLATE the walls, the ceiling and notes
B = HINGED SIDE 530 mm c/c * The incomplete detail of the footing/foundation of an internal and an
C = FIXED PANEL DOOR 9 mm CEILING BOARD ON
external wall
1000
2738
WINDOW (W1)
2700
* A door frame profile
* The incomplete floor plan of the bathroom, drawn to scale 1 : 25, on
2050
FIXTURES page 53
1550
3600
Instructions:
* Answer this question on page 53.
412
300
3. A sectional elevation on cutting plane B-B
* ALL drawings must comply with the guidelines and graphical
750
700
600
GROUND LEVEL 400
symbols contained in the SANS 10143.
INCOMPLETE FOOTING 111
SPECIFICATIONS:
550
DETAIL
32
44
Add the following features to the drawing:
INCOMPLETE FOUNDATION 33 45 33 * The door and windows
AND EXTERNAL WALL * The north direction
DETAIL INCOMPLETE DOOR FRAME PROFILE * ALL the fixtures as indicated by abbreviations
850
222 1484
SYMBOLS * ALL hatching details
222
295
B WC
* ALL features to the south of cutting plane A-A
n x 40W
* ALL features to the west of cutting plane B-B
* ALL hatching detail
W1
TOILET (WC)
1590
1 2
A A Label the following:
FEATURES: * The room designation and floor finish (tiles)
250
295
FIXTURES:
correct view: natural ground level, finished floor level and damp-proof
ROOF B BATH course.
111
D
COMPONENTS WC TOILET
3
WB WASH-BASIN
585 INCOMPLETE FLOOR PLAN B Note:
SCALE 1 : 25 ELECTRICAL FIXTURES: ONLY the substructures hatching may be drawn in neat freehand.
1. CEILING LIGHT
450
COPYRIGHT © JP
KOPIEREG © JP
NAME: CIVIL DRAWING
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
VENSTERSKEDULE GELYK GELYK VRAAG: SIVIELE TEKENING
1000 530 s/s 530 s/s 530 s/s 530 s/s
Gegee:
* Die onvolledige deursnee-aansig A-A van 'n badkamer, wat die mure
VENSTERNOTAS: 38 x 38 mm PLAFONNOTAS:
A = OOPMAAKKANT 114 x 38 mm
PLAFONLATTE
9 mm die plafon en notas toon
MUURPLAAT PLAFONBORD 114 x 38 mm MUURPLAAT
B = SKARNIERKANT 530 mm s/s * Die onvolledige besonderhede van die voet/fondasie van 'n
C = VASTE PANEEL DEUR- 9 mm PLAFONBORD OP binnemuur en 'n buitemuur
1000
B A C HOOGTE 38 x 38 mm PLAFONLATTE * Die onvolledige vloerplan wat die mure, posisie van die deur en
50
LET WEL: vensters, die toebehore en die elektriese uitleg toon
150 x 25 VESELSEMENT-
VENSTERBANK ONDER
* 'n Vensterskedule
ALLE VENSTERS * 'n Tabel met elektriese simbole
525
* 'n Tabel met dakkomponente
* 'n Tabel met toebehore
* 'n Deurraamprofiel
2738
VENSTER (V1)
2700
* Die onvolledige vloerplan van die badkamer, geteken volgens
2050
TOEBEHORE skaal 1 : 25, op bladsy 53
1550
3600
Instruksies:
* Beantwoord hierdie vraag op bladsy 53.
* Gebruik die gegewe onvolledige vloerplan en teken, volgens
412
111
skaal 1 : 25 en in eerstehoekse ortografiese projeksie, die volgende
aansigte van die badkamer:
1. Die volledige vloerplan
2. 'n Deursnee-aansig volgens snyvlak A-A
3. 'n Deursnee-aansig volgens snyvlak B-B
300
* ALLE tekene moet voldoen aan die riglyne en grafiese simbole
750
700
vervat in die SANS 10143.
600
GRONDVLAK 400
BAD (B)
EN BINNEMUUR- DIE VLOERPLAN
500
300
BESONDERHEDE
Voeg die volgende kenmerke by die tekening:
32
44
* Die deur en die vensters
33 45 33
ONVOLLEDIGE VOET- * Die noordrigting
EN BINNEMUUR-
BESONDERHEDE ONVOLLEDIGE DEURRAAMPROFIEL
* ALLE toebehore soos deur die afkortings aangedui
850
DEURSNEE-AANSIG A-A * ALLE elektriese toebehore soos deur die nommers aangedui
ELEKTRIESE B * ALLE arseringsbesonderhede
400
222 1484
SIMBOLE
DEURSNEE-AANSIG A-A EN B-B
222
V1
Toon die vogende kenmerke op die tekening:
* Die volledige voet- of fondasie-, muur- en plafonbesonderhede
250
295
TOILET (SK)
1590
A 1 A
2 Benoem die volgende:
* Die kameraanduiding en vloerafwerking (teëls)
KENMERKE: * Die deursnee-aansig A-A en deursnee-aansig B-B
250
295
TOEBEHORE: vogweerlaag
DAK- B BAD
111
D
KOMPONENTE SK TOILET
3
WB WASBAK
LET WEL:
585 ONVOLLEDIGE VLOERPLAN B SLEGS die substruktuurarsering mag in netjiese vryhand geteken
SKAAL 1 : 25 ELEKTRIESE TOEBEHORE: word.
1. PLAFONLIG
450
COPYRIGHT © JP
KOPIEREG © JP
NAAM: SIVIELE TEKENING
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
DPC DPC
FFL FFL
DPC DPC
NGL NGL
RUBRIC CORRECTNESS
B OUTSTANDING
WC VERY GOOD
GOOD
2 x 40W
A A
BATHROOM
TILES VERY BAD
WB NC NC NC
NON COMPLIANCE
QUALITY & NEATNESS
OUTSTANDING
VERY BAD
FLOOR PLAN B NON COMPLIANCE NC NC NC
SCALE 1 : 25 TOTAL 10
COPYRIGHT © JP
KOPIEREG © JP
NAME: CIVIL DRAWING
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
VWL VWL
VVV VVV
VWL VWL
NGV NGV
RUBRIEK KORREKTHEID
B UITSTEKEND
SK BAIE GOED
GOED
2 x 40W
A A
BADKAMER
TEËLS BAIE SWAK
WB NV NV NV
NIE VOLDOEN
KWALITEIT & NETHEID
UITSTEKEND
BAIE SWAK
VLOERPLAN B NIE VOLDOEN NV NV NV
SKAAL 1 : 25 TOTAAL 10
COPYRIGHT © JP
KOPIEREG © JP
NAAM: SIVIELE TEKENING
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
QUESTION: CIVIL DRAWING
WINDOW SCHEDULE
Given:
500 800 500 ROOF CONSTRUCTION
(GR 12) * The incomplete sectional west elevation of a new granny flat
showing the postion of the walls, the foundation and complete
roof detail
* The incomplete floor plan showing the walls, position of the
HINGED CEILING HEIGHT windows, doors, fixtures and electrical features
END * The incomplete foundation and wall detail
1500
DOOR HEIGHT
FIXED
* A window schedule
PANEL * A table of sanitary fixtures
* A table of electrical symbols
25 25 * Incomplete floor plan of the new granny flat, drawn to scale
2100
1 : 50, on page 55
END PANEL SILL UNDER INCOMPLETE SECTIONAL 1. The complete floor plan
ALL WINDOWS WEST ELEVATION 2. The complete sectional elevation on cutting plane A-A
RWDP RWDP * ALL drawings must comply with the guidelines and graphical
W2
symbols contained in SANS 10143.
WINDOW (W2) 2
ELECTRICAL FITTINGS
1. DISTRIBUTION BOARD 10 9 SPECIFICATIONS:
2. SWITCHED SOCKET OUTLETS THE FLOOR PLAN
SANITARY FIXTURES
BIC
3. CEILING LIGHT
4. 2 x 40 W FLUORESCENT TUBES
Add the following features to the drawing:
5. WALL MOUNTED LIGHT * ALL the doors and windows.
W2 11 3 3 W1
6. SINGLE-POLE LIGHT SWITCH * ALL the fixtures as indicated by numbers
800
7. TWO-POLE LIGHT SWITCH A 6 A * ALL electrical fittings as indicated by the numbers
8. THREE-POLE LIGHT SWITCH BEDROOM * ALL hatching detail.
NOTE: BATHROOM D D
3 * North direction and step direction
THE ARROW SHOW THE LIGHT
ROOF LINE
ROOF LINE
800
ROOF LINE
SHOWER (SH)
11. WASH-BASIN (WB)
LOUNGE
* The window detail, with a DOUBLE lintel
12. SINK (S) * ALL features east of cutting plane A-A
500 * ALL hatching detail
585
FEATURES 4 3 2
D - DOOR
W1 - WINDOW W2 12 Label the following:
285
230 126
850
500
400
400
1200
500
500
250
250 n x 40W
510
COPYRIGHT © JP
KOPIEREG © JP
NAME: CIVIL DRAWING
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
VRAAG: SIVIELE TEKENING
VENSTERSKEDULE
Gegee:
500 800 500 DAKKONSTRUKSIE
(GR 12) * Die onvolledige deursnee-wesaansig van 'n nuwe eenman-
woonstel wat die posisie van die mure, die fondasie- en
volledige dakbesonderhede toon
* Die onvolledige vloerplan wat die mure, posisie van die vensters,
SKARNIER- PLAFONHOOGTE die deure, toebehore en die elektriese kenmerke toon
KANT * 'n Vensterskedule
DEURHOOGHTE
1500
VASTE
* 'n Tabel met sanitere
ê toebehore
PANEEL * Die onvolledige fondasie- en muurbesonderhede
* 'n Tabel met elektriese simbole
25 25 * Die onvolledige vloerplan van die nuwe eenmanwoonstel,
2100
geteken volgens skaal 1 : 50, op bladsy 55
IGK
SANITÊRE TOEBEHORE 3. PLAFONLIGTE
4. 2 x 40 W FLUORESSEERBUISE Voeg die volgende kenmerke by die tekening:
5. MUURGEMONTEERDE LIG * ALLE deure en vensters
V2 11 3 3 V1
6. EENPOOLLIGSKAKELAAR * ALLE toebehore soos deur die nommers aangedui
800 7. TWEEPOOLLIGSKAKELAAR A 6 A * ALLE elektriese toebehore soos deur die nommers aangedui
8. DRIEPOOLLIGSKAKELAAR SLAAPKAMER * ALLE arseringsbesonderhede
LET WEL: BADKAMER D 3 D * Noordrigting en traprigting
DIE PYL TOON DIE LIGVER-
DAKLYN
800
DAKLYN
BINDING MET DIE SKAKELAAR 7
AAN.
DIE DEURSNEEAANSIG
2 2 Voeg die volgende kenmerke op die tekening:
TOEBEHORE * Die volledige fondasie- en muurbesonderhede tot op
9. TOILET (SK) plafonhoogte
DAKLYN
STORT (ST) 10. STORT (ST) SITKAMER
11. WASBAK (WB) * Die vensterbesonderhede, met 'n DUBBEL latei
500 12. OPWASBAK (OWB) * ALLE kenmerke oos van snyvlak A-A
585
4 3 2 * ALLE arseringsbesonderhede
KENMERKE V2 12
285
V2 - VENSTER
850
* Die deursnee-aansig
1 8
400
230 126
850
500
500
400
400
1200
500
500
250
250 n x 40W
510
COPYRIGHT © JP
KOPIEREG © JP
NAAM: SIVIELE TEKENING
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
1
DPC
DPC
FFL
DPC DPC
NGL NGL
SH
WC
BIC
A WB
A
BEDROOM
BATHROOM TILES
TILES
ROOF LINE
ROOF LINE
RUBRIC CORRECTNESS
LOUNGE
ROOF LINE
OUTSTANDING
TILES VERY GOOD
GOOD
2 x 40W
KITCHEN
TILES
VERY BAD
NON COMPLIANCE NC NC
QUALITY & NEATNESS
RWDP RWDP
OUTSTANDING
VERY BAD
FLOOR PLAN NON COMPLIANCE NC NC
SCALE 1 : 50 TOTAL 10
COPYRIGHT © JP
KOPIEREG © JP
NAME: CIVIL DRAWING
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
1
VWL
VWL
VVV
VWL VWL
NGV NGV
ST
SK
IGK
A WB
A
SLAAPKAMER
BADKAMER TEËLS
TEËLS
DAKLYN
DAKLYN
RUBRIEK KORREKTHEID
SITKAMER UITSTEKEND
DAKLYN
KOMBUIS
TEËLS
BAIE SWAK
NIE VOLDOEN NV NV
KWALITEIT & NETHEID
RWAP RWAP
UITSTEKEND
BAIE SWAK
VLOERPLAN NIE VOLDOEN NV NV
SKAAL 1 : 50 TOTAAL 10
COPYRIGHT © JP
KOPIEREG © JP
NAAM: SIVIELE TEKENING
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
QUESTION: CIVIL DRAWING
ELECTRICAL SYMBOLS
Given:
* The incomplete sectional west elevation on cutting plane
W A-A of a new cottage showing the outline of the walls and
the roof truss
ROOF CONSTRUCTION * The incomplete floor plan of the new cottage showing the
(GR 12)
n x 40W outerline of the walls and the positions of all the features,
relevant notes and dimensions
DOOR AND WINDOW HEIGHT * A tabel of electrical symbols
* A door and window schedule
2758 TO CEILING
DOOR & WINDOW SCHEDULE * Detailed drawing of all the sanitary fixtures
FRAME DOOR * The incomplete foundation and wall detail
2125
2 x STANDARD EXTERNAL
2 x PANEL DOORS
* Detailed drawing of the metal door frame profile
STEEL FRAMES On page 57 drawn to scale 1 : 50:
877 813
25 mm - Walls AB, CD, EF, window ND7 and the work top of the
242
FLOOR LEVEL SCREED incomplete floorplan of the cottage
- The incomplete north elevation of the cottage
525
550
440
WINDOW - Walls AB and EF of the incomplete west elevation
550
GROUND LEVEL SILL TILE
2125
300
170 x 35
650
250
INCOMPLETE SECTIONAL Instructions:
WEST ELEVATION INCOMPLETE FOUNDATION * Answer this question on page 57.
AND WALL DETAIL * Using the given incomplete floor plan, draw in first-angle
WINDOWS WINDOWS
orthographic projection and to scale 1 : 50, the following
2 x ND 7 STANDARD SIZED 3 x ND 1 STANDARD SIZED views of the cottage:
STEEL FRAME STEEL FRAME 4196 1541 1134 1. The complete floor plan
1000 500 ROOF LINE 2. The complete sectional west elevation on cutting
plane A-A
500
DOOR OPENING 2 WINDOW ND1
* ALL drawings must comply with the graphic symbol and
A F
guidelines contained in the SANS 0143.
6 1
1200
1200
1935
SPECIFICATIONS:
25 4
THE FLOOR PLAN
WINDOW ND7
3363
CENTRE LINE AND POSITION OF
* ALL the walls with hatching detail
GLAZING
ND7
3mm CLEAR GLASS
ND1 3 THE 131 mm NON LOAD-BEARING * The doors and windows
5 WALL, PLASTERED ON BOTH * The graphic symbols and abbreviations of ALL the
SIDES
sanitary fixtures as indicated on the incomplete floorpan on
FOLDING DOOR page 57
SANITARY FIXTURES
1 7 4 * ALL the electrical features as indicated with numbers on
B E the incomplete floor plan
500
500 WINDOW ND7 DOOR OPENING WINDOW ND1
WINDOW ND1
585
ROOF LINE BEDROOM OUTSIDE LINE OF A 242 mm
LOAD-BEARING WALL THE SECTIONAL WEST ELEVATION
1099
A A Show the following features on the drawing:
850
850
300 549
* The door and window detail with a single lintel (242 x 85)
C D
300
above the window
300 400 400 473 500 3363 500 1000 300 * 170 x 35 fibre cement sill under ALL windows
250
450
WASH BASIN
* Only the outside detail of the rest of the cottage as seen
ELECTRICAL FEATURES: from the west
800 1. SINGLE-POLE LIGHT SWITCHES 5. TWO-POLE LIGHT SWITCH
TOILET (WC) 2. OUTSIDE LIGHT 6. SWITCHED SOCKET OUTLETS
3. 3 x 40 W FLUORESCENT TUBES 7. DISTRIBUTION BOARD 262 Label the following:
1200 4. CEILING LIGHT * The sectional elevation
32
* Using the correct abbreviations, label the following
800
12
45 172 45
510
COPYRIGHT © JP
KOPIEREG © JP
NAME: CIVIL DRAWING
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
ELEKTRIESE SIMBOLE
W
DAKKONSTRUKSIE
(GR 12)
n x 40W
DEUR- EN VENSTERHOOGTE
2758 NA PLAFON
DEUR- & VENSTERSKEDULE
RAAM DEUR
2125
2 x STANDAARD EKSTERNE
2 x PANEELDEURE
STAALRAME
877 813
242 25 mm
VLOERVLAK VLAKLAAG
525
550
440
VENSTERBANK-
550
GRONDVLAK TEËL
2125
300
170 x 35
650
250
ONVOLLEDIGE DEURSNEE-
WESAANSIG ONVOLLEDIGE FONDASIE-
& MUURBESONDERHEDE
VENSTER VENSTER
2 x ND 7 STANDAARD- 3 x ND 1 STANDAARD-
GROOTTE STAALRAAM GROOTTE STAALRAAM 4196 1541 1134
1000 500 DAKLYN
500
DEUROPENING 2 VENSTER ND1
A F
6 1
1200
1200
SKARNIERKANT SKARNIERKANT
1935
25 4
VENSTER ND7
KOMBUIS BADKAMER
3363
GLAS SENTERLYN EN POSISIE VAN
ND7
3mm HELDER GLAS
ND1 S 3 DIE 131 mm NIE-LASDRAENDE
5 MUUR, BEIDE KANTE
GEPLEISTER
VOUDEUR
SANITÊRE TOEBEHORE
1 7 4
B E
500
500 VENSTER ND7 DEUROPENING VENSTER ND1
VENSTER ND1
585
DAKLYN SLAAPKAMER BUITELYN VAN 'N 242 mm
LASDRAENDE MUUR
1099
A A
850
850
300 549
6
400
C D
300
300 400 400 473 500 3363 500 1000 300
250
450
ONVOLLEDIGE VLOERPLAN
850
WASBAK
ELEKTRIESE KENMERKE:
800 1. ENKELPOOL-LIGSKAKELAAR 5. TWEEPOOL-LIGSKAKELAAR
TOILET (SK) 2. BUITELIG 6. SKAKELAARKRAGPUNTE
3. 3 x 40 W FLUORESSEERBUISE 7. DISTRIBUSIEBORD 262
1200 4. PLAFONLIG
32
800
12
45 172 45
510
COPYRIGHT © JP
KOPIEREG © JP
NAAM: SIVIELE TEKENING
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
DPC
A F
WB
WC
KITCHEN BATHROOM
S Tiles SH
Tiles
3 x 40W
RUBRIC CORRECTNESS
OUTSTANDING
B E VERY GOOD
GOOD
BEDROOM
Tiles
A A
VERY BAD
NON COMPLIANCE NC NC
C D QUALITY & NEATNESS
OUTSTANDING
FLOOR PLAN
SCALEL 1:50
VERY BAD
NON COMPLIANCE NC NC
TOTAL 10
COPYRIGHT © JP
KOPIEREG © JP
NAME: CIVIL DRAWING
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
VWL
DEURSNEE- WESAANSIG
A F
WB
SK
KOMBUIS BADKAMER
S Teëls ST
Teëls
3 x 40W
RUBRIEK KORREKTHEID
UITSTEKEND
B E BAIE GOED
GOED
SLAAPKAMER
Teëls
A A
BAIE SWAK
NIE VOLDOEN NV NV
C D KWALITEIT & NETHEID
UITSTEKEND
PLAN
SKAAL 1:50
BAIE SWAK
NIE VOLDOEN NV NV
10
COPYRIGHT © JP
KOPIEREG © JP
NAAM: SIVIELE TEKENING
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
QUESTION: CIVIL DRAWING
WINDOW SCHEDULE CEILING HEIGHT
WALL PLATE CEILING Given:
DOOR HEIGHT
114 x 38 mm HEIGHT * The incomplete sectional west elevation of a new granny flat
500 800 500 with outlines of the walls and the incomplete foundation detail
WALL PLATE up to ceiling height
900
114 x 38 mm * The incomplete floor plan with cutting plane A-A of the new
2700
granny flat showing the outlines of the exterior walls, the
centre lines of the interior walls, the position of all the features,
2100
relevant notes and dimensions
1500
900
* A window schedule
* Detailed drawings of all the sanitary fixtures
25 25
* A tabel of electrical symbols
* Standard door frames
GROUND LEVEL
WINDOW (W1) WINDOW (W2) Instructions:
INCOMPLETE SECTIONAL WEST
* Answer this question on page 59.
NOTE: ELEVATION OF FOUNDATION
126 * Draw, to scale 1 : 50 and the given specifications:
180 x 25 FIBRE CEMENT
SILL UNDER 230 25 mm SCREED 1. The complete floor plan
25 mm SCREED
ALL WINDOWS 2. The complete west sectional elevation on cutting plane A-A
KEY TO NUMBERED FEATURES ON PLAN: * ALL drawings must comply with the guidelines contained in
500
400
1. DISTRIBUTION BOARD 7. TWO-POLE LIGHT SWITCH
250
NGL the SANS 10143.
500
500
2. SWITCH SOCKET OUTLET 8. SINK (S)
400
250
SANITARY FIXTURES 3. CEILING LIGHT 9. SHOWER (SH)
500
SPECIFICATIONS:
4. 2 x 40 W FLUORESCENT TUBES 10. TOILET (WC) 400
THE FLOOR PLAN
700 5. WALL MOUNTED LIGHT 11. WASH-BASIN (WB)
INCOMPLETE FOUNDATION Show the following features on the drawing:
6. ONE-POLE LIGHT SWITCH AND INTERNAL WALL DETAIL
510
800
850
800
fixtures
400
FLOOR LEVEL
WINDOW (W2)
2 6 Show the following features on the drawing up to floor height:
3 * Exterior walls with window and foundation detail
900
250
DOOR
A * ALL features to the west of the cutting plane
850
600
WASH-BASIN (WB) - A single lintel (230 x 85) above the windows
A
WINDOW (W1)
TOILET (WC)
3 1 - Wall plate 114 x 38 mm
900
- ALL hatching detail
ELECTRICAL SYMBOLS 2 - Labels: Damp-proof course, natural ground level, finished
4
WINDOW (W2)
LIGHTS LIGHT SWITCHES POWER OUTLET floor level and floor finish (tiles)
Note:
900
ALL substructure hatching may be drawn in freehand.
DOOR FRAME
1675
1050
n x 40W 8 34
34
7 6
DOOR
135
95
WINDOW (W1) 5
48
90
DISTRIBUTION BOARD ELECTRICITY METER EARTH STEP
600 mm
2 @ 900 x 250 STEPS WORK TOP 46
46
600 1800 450 900 2800
W
EXTERNAL DOOR INTERNAL DOOR
INCOMPLETE FLOOR PLAN
COPYRIGHT © JP
KOPIEREG © JP
NAME: CIVIL DRAWING
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
VRAAG: SIVIELE TEKENING
VENSTERSKEDULE PLAFONHOOGTE
MUURPLAAT PLAFON- Gegee:
114 x 38 mm HOOGTE * Die onvolledige deursnee-wesaansig van 'n nuwe tuinwoonstel
DEURHOOGTE
500 800 500 met die buitelyne van die mure en onvolledige fondasie-
MUURPLAAT besonderhede tot op plafonhoogte
900 114 x 38 mm * Die onvolledige vloerplan met 'n snyvlak A-A van die nuwe
2700
tuinwoonstel wat die buitelyne van die buitemure, die
2100
senterlyne van die binnemure, die posisie van al die kenmerke,
relevante notas en afmetings toon
1500
900
* 'n Vensterskedule
* Gedetailleerde tekeninge van al die sanitêre toebehore
25 25
* 'n Tabel met elektriese simbole
VLOERHOOGTE
* Standaard deurkosyne
GRONDVLAK
VENSTER (V1) VENSTER (V2) Instruksies:
ONVOLLEDIGE DEURSNEE-
WESAANSIG VAN FONDASIE * Beantwoord hierdie vraag op bladsy 59.
LET WEL: 126 * Teken, volgens skaal 1 : 50 en die gegewe spesifikasies:
180 x 25 VESELSEMENT- 25 mm VLAKLAAG
VENSTERBANK ONDER
230
25 mm VLAKLAAG
1. Die volledige vloerplan
ALLE VENSTERS 2. Die volledige deursnee-wesaansig op snyvlak A-A
SLEUTEL TOT GENOMMERDE KENMERKE OP PLAN: * ALLE tekeninge moet voldoen aan die riglyne vervat in die
500
400
1. DISTRIBUSIEBORD 7. TWEEPOOLLIGSKAKELAAR
250
NGV SANS 10143.
500
500
2. SKAKELAARKRAGPUNT 8. OPWASBAK (OWB)
400
250
SANITÊRE TOEBEHORE 3. PLAFONLIG 9. STORT (ST)
500
400
SPESIFIKASIES:
4. 2 x 40 W FLUORESSEERBUISE 10. TOILET (SK)
5. MUURGEMONTEERDE LIG 11. WASBAK (WB)
DIE VLOERPLAN
700 ONVOLLEDIGE FONDASIE- EN Toon die volgende kenmerke op die tekening:
6. EENPOOLLIGSKAKELAAR BINNEMUURBESONDERHEDE
510
800
850
toebehore
400
DIE DEURSNEE-WESAANIG:
1675
VENSTER (V2)
VLOERVLAK
2 6 Toon die volgende kenmerke op die tekening tot op
3 plafonhoogte:
250
DEUR
A * Die posisie van die interne muur en fondasiebesonderhede
850
VENSTER (V2)
LIGTE LIGSKAKELAARS KRAGPUNTE - Byskrifte: Vogweerlaag, natuurlke gronvlak, voltooide
vloervlak en vloerafwerking (teëls)
Let wel:
ALLE substruktuurarserig mag in vryhand geteken word.
1675
DEURKOSYN
n x 40W 8 34
7 6 34
DEUR
135
95
VENSTER (V1) 5
48
90
DISTRIBUSIEBORD ELEKTRIESE METER AARD TRAP
600 mm
2 @ 900 x 250 TRAPPIES WERKSBLAD 46
46
900
W
EKSTERNE DEUR INTERNE DEUR
ONVOLLEDIGE VLOERPLAN
COPYRIGHT © JP
KOPIEREG © JP
NAAM: SIVIELE TEKENING
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
DPC
FFL
DPC DPC
NGL NGL
SH
WC
BATHROOM A
LOUNGE TILES WB
A TILES
2 x 40W
KITCHEN
TILES RUBRIC CORRECTNESS
OUTSTANDING
VERY GOOD
S GOOD
VERY BAD
FLOOR PLAN NON COMPLIANCE NC NC
SCALE 1 : 50 QUALITY & NEATNESS
OUTSTANDING
VERY BAD
NON COMPLIANCE NC NC
TOTAL 10
COPYRIGHT © JP
KOPIEREG © JP
NAME: CIVIL DRAWING
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
VWL
VVV
VWL VWL
NGV NGV
ST
SK
BADKAMER A
SITKAMER TEËLS WB
A TEËLS
2 x 40W
KOMBUIS
TEËLS RUBRIEK KORREKTHEID
UITSTEKEND
BAIE GOED
OWB GOED
BAIE SWAK
VLOERPLAN NIE VOLDOEN NV NV
SKAAL 1 : 50 KWALITEIT & NETHEID
UITSTEKEND
BAIE SWAK
NIE VOLDOEN NV NV
TOTAAL 10
COPYRIGHT © JP
KOPIEREG © JP
NAAM: SIVIELE TEKENING
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
CEILING HEIGHT
QUESTION: CIVIL DRAWING
ELECTRICAL SYMBOLS WALL PLATE
114 x 38 mm
Given:
W * The incomplete sectional south elevation on cutting plane A-A of a
kitchen, showing the walls, the ceiling height and wall plate
* The incomplete foundation, wall detail of an internal and an external
n x 40W wall
2600
* The incomplete floor plan showing the walls, position of the doors
and windows, the fixtures and electrical layout
2100
WORK TOP HEIGHT * A tabel of electrical symbols
WINDOW & DOOR SCHEDULE
* A window and door schedule
SCREED SCREED
25 mm 25 mm * A table of fixtures
900
111 222 * A door frame profile
2000
100
* The incomplete floor plan of the bathroom, drawn to scale 1 : 50,
FLOOR SLAB HEIGHT
on page 61
350
B B B B
A
600
A A A = OPENING SIDE GROUND LINE
C B = HINGED SIDE
Instructions:
B B C = FIXED PANEL * Answer this question on page 61.
* Using the given incomplete floor plan, draw, in first-angle
250
500 450 INCOMPLETE SECTIONAL
500 SOUTH ELEVATION ON A-A 700 orthographic projection and to scale 1 : 50, the following views of the
NOTE: 150 x 20 FIBRE CEMENT kitchen:
SILL UNDER ALL WINDOWS INCOMPLETE FOUNDATION B INCOMPLETE FOUNDATION 1. The complete floor plan
AND INTERNAL WALL DETAIL AND EXTERNAL WALL DETAIL
WINDOW (W1 & W2) 2. A sectional elevation on cutting plane A-A
3. A sectional elevation on cutting plane B-B
TO FIT TO FIT ROOF LINE * ALL drawings must comply with the guidelines and graphical
252 500 960
symbols contained in the SANS 10143.
300
6
W1 D1
SPECIFICATIONS:
572
THE FLOOR PLAN
475
600
1 S 1 (SINGLE) 3
2100
S 1 (DOUBLE)
111 mm INTERNAL WALLS
* ALL the electrical fittings as indicated by numbers
5
* ALL hatching details
W2
INTERNAL AND EXTERNAL FRAME AND DOOR (D1 & D2) 5
* The roof line
ROOF LINE
KITCHEN SCULLERY
524
BIC SECTIONAL ELEVATION A-A AND B-B
SANITARY FIXTURES Show the following features on the drawing:
* The complete foundation, wall, slab detail up to ceiling height with
2 2 the wall plate
350
450 3 2 * The window detail, with a DOUBLE lintel
1300
D2 * ALL features to the north of cutting plane A-A
* ALL features to the east of cutting plane B-B
B * ALL hatching detail
340
510
55
4. CEILING LIGHT
67
Note:
340
510
COPYRIGHT © JP
KOPIEREG © JP
NAME: CIVIL DRAWING
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
PLAFONHOOGTE
VRAAG: SIVIELE TEKENING
ELEKTRIESE SIMBOLE MUURPLAAT
114 x 38 mm
Gegee:
W * Die onvolledige deursnee-suidaansig volgens A-A van 'n kombuis,
wat die mure die plafonhoogte en muurplaat toon
* Die onvolledige fondasie- en muurbesonderhede van 'n binne- en
n x 40W buitemuur
2600
* Die onvolledige vloerplan wat die mure, posisie van die deure en
vensters, die toebehore en die elektriese uitleg toon
2100
WERKSBLADHOOGTE * 'n Tabel met elektriese simbole
VENSTER- EN DEURSKEDULE
* 'n Venster- en deurskedule
VLAKLAAG VLAKLAAG
25 mm 25 mm * 'n Tabel met toebehore
900
111 222 * 'n Deurraamprofiel
2000
100
* Die onvolledige vloerplan van die kombuis, geteken volgens
VLOERBLADHOOGTE
skaal 1 : 50, op bladsy 61.
350
B B B B
A
600
A A A = OOPMAAKKANT GRONDLYN
C B = SKARNIERKANT
Instruksies:
B B C = VASTE PANEEL * Beantwoord hierdie vraag op bladsy 61.
* Gebruik die gegewe onvolledige vloerplan en teken, volgens
250
500 450 ONVOLLEDIGE DEURSNEE-
500 SUIDAANSIG OP A-A 700 skaal 1 : 50 en in eerstehoeks ortografiese projeksie, die volgende
LET WEL: 150 x 20 VESELSEMENT- aansigte van die kombuis:
VENSTERBANK ONDER ALLE VENSTERS ONVOLLEDIGE FONDASIE- EN B ONVOLLEDIGE FONDASIE- EN 1. Die volledige vloerplan
BINNEMUURBESONDERHEDE BUITEMUURBESONDERHEDE
VENSTER (V1 & V2) 2. 'n Deursnee-aansig volgens snyvlak A-A
3. 'n Deursnee-aansig volgens snyvlak B-B
OM TE PAS OM TE PAS DAKLYN * ALLE tekene moet voldoen aan die riglyne en grafiese simbole
252 500 960
vervat in die SANS 10143.
300
6
V1 D1
SPESIFIKASIES:
572
DIE VLOERPLAN
475
600
1 OWB 1 (ENKEL) 3
2100
OWB 2 (DUBBEL)
SPENS SENTERLYN VAN
111 mm BINNEMURE
* ALLE elektriese toebehore soos deur die nommers aangedui
5
BINNE- EN BUITERAAM EN DEUR (D1 & D2) 5
* ALLE arseringsbesonderhede
V2
* Die daklyn
KOMBUIS OPWASKAMER
DAKLYN
524
IGK DEURSNEE-AANSIG A-A EN B-B
SANITÊRE TOEBEHORE Toon die vogende kenmerke op die tekening:
* Die volledige fondasie-, muur-, bladbesonderhede tot plafonhoogte
2 2 met die muurplaat
350
450 * Die vensterbesonderhede met 'n DUBBEL latei
3 2
1300
D2 * ALLE kenmerke noord van snyvlak A-A
* ALLE kenmerke oos van snyvlak B-B
B * ALLE arseringsbesonderhede
340
510
55
67
LET WEL:
340
510
TOEBEHORE: 5. FLUORESSEERBUIS 2 x 40 W
OWB 1 OPWASBAK (ENKEL) 6. MUURGEMONTEERDE LIG 45 SLEGS die substuktuurarsering mag in netjiese vryhand geteken word.
OWB 2 OPWASBAK (DUBBEL) LET WEL:
WERKSBLAD 600 mm DIEP EN DIE PYL TOON DIE LIGVERBINDING
OPWASBAK 2 (OWB)
900 mm HOOG MET DIE SKAKELAARS AAN. DEURRAAMPROFIEL
COPYRIGHT © JP
KOPIEREG © JP
NAAM: SIVIELE TEKENING
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
DPC
FFL FFL
DPC DPC
NGL NGL
B
SECTION A-A SECTION B-B
ROOF LINE
A A
S
PANTRY
2 x 40W
B
VERY BAD
FLOOR PLAN
SCALE 1 : 50 NON COMPLIANCE NC NC NC
QUALITY & NEATNESS
OUTSTANDING
VERY BAD
NON COMPLIANCE NC NC NC
TOTAL 10
COPYRIGHT © JP
KOPIEREG © JP
NAME: CIVIL DRAWING
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
VWL
VVV VVV
VWL VWL
NGV NGV
B
DEURSNEE A-A DEURSNEE B-B
DAKLYN
OWB
A A
OWB
SPENS
2 x 40W
B
BAIE SWAK
VLOERPLAN
NIE VOLDOEN NV NV NV
SKAAL 1 : 50
KWALITEIT & NETHEID
UITSTEKEND
BAIE SWAK
NIE VOLDOEN NV NV NV
TOTAAL 10
COPYRIGHT © JP
KOPIEREG © JP
NAAM: SIVIELE TEKENING
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
DOOR & WINDOW SCHEDULE QUESTION: CIVIL DRAWING
500 500 500 BARGE BOARD ROOF CONSTRUCTION
1000 (GR 12) Given:
PANEL PANEL
125 x 100 GUTTER * The incomplete southern elevation of a new cottage showing the
SLIDES TO
THE RIGHT
SLIDES TO
THE LEFT 200 x 20 walls, the windows, the front door and the roof and notes
* The incomplete floor plan, showing the walls, position of the
1200
1100
1000
900
FIXED HINGE HINGE FACIA BOARD
PANEL SIDE SIDE
FINISHED Ø100mm windows, doors, fixtures and the electrical fittings
50 50 FLOOR LEVEL
RWDP * Incomplete foundation and wall detail
GROUND LEVEL * The floor finishes and a diagram showing the room designations
WINDOW (W1) WINDOW (W2) FEATURES: * A door and window schedule
D1 INTERNAL DOOR OPENING RE * A table of electrical symbols
NOTE: 170 x 35 FIBRE CEMENT SILL UNDER ALL WINDOWS
500
D2 FRONT DOOR OPENING 45° SEWER LINE 1:40
Ø 110 PVC INCOMPLETE * A table of fixtures
W1 WINDOW OPENING SOUTHERN ELEVATION
W2 WINDOW OPENINGS * The incomplete floor plan, sectional and south elevation of the
RE IE RE
TO FIT TO FIT FIXTURES: new cottage, drawn to scale 1:50 on page 63
WC TOILET RWDP
SH SHOWER IE
WB WASH-BASIN W2 W2 Instructions:
BIC BUILT-IN CUPBOARD (600 mm)
WB
* Answer this question on page 63.
WC
IE 1 * Using the given incomplete views, draw, to scale 1:50 and in
ELECTRICAL FITTINGS: 3 3 BIC
2 first-angle orthographic projection the following views of the new
2100
2100
850
BATHROOM: TILES
KITCHEN
LOUNGE: TILES * The window detail with a DOUBLE lintel
ELECTRICAL FLOOR LEVEL LOUNGE BEDROOM: CARPET * ALL sanitary fixtures to the east of the cutting plane
SYMBOLS
* ALL hatching detail
W
250
2700
550
level, sewer line, built-in cupboard and sanitary fixtures
440
440
800
NOTE:
550
550
n x 40W
ALL substructure hatching may be drawn in freehand.
650 450
250
250
800
INCOMPLETE FOUNDATION INCOMPLETE FOUNDATION
SHOWER (SH)
AND EXTERNAL WALL DETAIL AND INTERNAL WALL DETAIL
COPYRIGHT © JP
KOPIEREG © JP
NAME: CIVIL DRAWING
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
VRAAG: SIVIELE TEKENING
DEUR- & VENSTERSKEDULE
1100
1000
900
VASTE SKARNIER- SKARNIER- FASSIEPLANK
PANEEL KANT KANT vensters, deure, toebehore en die elektriese toebehore toon
VOLTOOIDE Ø100mm
50 50 VLOERVLAK * Onvolledige fondasie- en muurbesonderhede
RWAP
* Die vloerafwerking en 'n diagram wat die kameraanduidings toon
GRONDVLAK
* 'n Deur- en vensterskedule
KENMERKE:
VENSTER (V1) VENSTER (V2)
SO * 'n Tabel van elektriese simbole
D1 BINNEDEUROPENINGE
LET WEL: 170 x 35 VESELSEMENT-VENSTERBANK ONDER ALLE VENSTERS * 'n Tabel van toebehore
500
D2 VOORDEUROPENING 45° RIOOLLYN 1:40
Ø 110 PVC ONVOLLEDIGE
V1 VENSTEROPENING SUIDAANSIG * Die onvolledige vloerplan, deursnee-aansig en suidaansig van die
OM TE OM TE V2 VENSTEROPENINGE SO IO SO nuwe kothuis, geteken volgens skaal 1:50, op bladsy 63
PAS PAS TOEBEHORE:
SK TOILET RWAP
ST STORT IO Instruksies:
WB WASBAK V2 V2
* Beantwoord hierdie vraag op bladsy 63.
IGK INGEBOUDE KAS (600 mm)
SK WB * Gebruik die gegewe onvolledige aansigte en teken, volgens
IO 1
ELEKTRIESE TOEBEHORE: 3 3 IGK skaal 1:50 en in eerstehoekse ortografiese projeksie, die
2
2100
2100
* ALLE arseringsbesonderhede
850
W DIE SUID-AANSIG
250
KAMERAANDUIDINGS MET
Voeg die volgende kenmerke op die tekening:
450
VLOERAFWERKING
* Die buitemure, die voltooide vloervlak en rioollyn
850
* Die reënwaterafvoerpyp
2700
550
550
440
440
800
toebehore.
550
550
800
ONVOLLEDIGE FONDASIE- EN ONVOLLEDIGE FONDASIE- EN
STORT (ST)
BUITEMUURBESONDERHEDE BINNEMUURBESONDERHEDE
COPYRIGHT © JP
KOPIEREG © JP
NAAM: SIVIELE TEKENING
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
DPC
DPC
FFL FFL
DPC DPC
RE
NGL NGL NGL
SEWER LINE 1:40
Ø 110 PVC SOUTHERN ELEVATION
IE
RE RE
RWDP
IE
BIC
BIC
BEDROOM
WB CARPET
WC
IE
BATHROOM
SH TILES
VERY BAD
ROOF LINE RWDP
NON COMPLIANCE NC NC
QUALITY & NEATNESS
RE RE
IE OUTSTANDING
FLOOR PLAN
SCALE 1:50
VERY BAD
NON COMPLIANCE NC NC
TOTAL 10
COPYRIGHT © JP
KOPIEREG © JP
NAME: CIVIL DRAWING
GRADE 11:
ENGINEERING GRAPHICS & DESIGN DATE:
VWL
VWL
VVV VVV
VWL VWL
SO
NGV NGV NGV
RIOOLLYN 1:40
Ø 110 PVC SUIDAANSIG
DEURSNEE OOSAANSIG
IO
SO SO
RWAP
IO
IGK
IGK
SLAAPKAMER
WB MAT
SK
IO
BADKAMER
ST TEËLS
BAIE SWAK
DAKLYN RWAP
NIE VOLDOEN NV NV
KWALITEIT & NETHEID
SO SO
IO UITSTEKEND
VLOERPLAN
SKAAL 1:50
BAIE SWAK
NIE VOLDOEN NV NV
TOTAAL 10
COPYRIGHT © JP
KOPIEREG © JP
NAAM: SIVIELE TEKENING
GRAAD 11:
INGENIEURSGRAFIKA & ONTWERP DATUM:
1 X3
A B
6 2 Y
X1
T Y3
F C 21 2 1
2 1
5 3 21
36 3 6
E D
4M T 36 T
3 6
45 B 4 5
B
X 5 A
CA C 4
45 N
D F
DF
E E
X2 Y2
3 3
D C
Y1
4
24 2
E
T B
5 15 1
F A
6 6
QUESTION: VRAAG: QUESTION: VRAAG:
Given: Gegee: Given: Gegee:
* The front view, auxiliary view and a cutting plane A-A of: * Die vooraansig, hulpaansig en 'n snyvlak A-A van: * The front view, auxiliary view and a cutting plane A-A of: * Die vooraansig, hulpaansig en 'n snyvlak A-A van:
QUESTION A: A right regular triangular prism. VRAAG A: 'n Regte reëlmatige driehoekige prisma. QUESTION A: A right regular triangular pyramid. VRAAG A: 'n Regte reëlmatige driehoekige piramide.
QUESTION B: A right regular square prism. VRAAG B: 'n Regte reëlmatige vierkantige prisma. QUESTION B: A right regular square pyramid. VRAAG B: 'n Regte reëlmatige vierkantige piramide.
A A
X2 X2
2 2 T T
A
A
1 1
2 2
3 2 2
3 X
NC
X
NC
A 1 A
1 1 1
3 3 1 NC 3 3 1 NC
10 10
Y1 2 Y1 2
1 Y 1 X1 Y 1 X1
T
T
3 3
3 32 2 3 2
Y2 Y2
B B
2 2
X
2 X2 3
2 X 3
A X2 2
2
1 A
2 2 1
3 1 4
3 1 1
3 1 3
NC 4 NC
3 4 1 1 A
3 4 Y A
4 4 Y
NC T NC
4 4 10 T 10
Y1 X1 Y1 X1
1 1 1
2
2 4 T 4
4 2
3
3 3 Y2
Y2
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: SOLIDS / VASTE LIGGAME
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: VRAAG: QUESTION: VRAAG:
Given: Gegee: Given: Gegee:
* The front view, auxiliary view and a cutting plane A-A of: * Die vooraansig, hulpaansig en 'n snyvlak A-A van: * The front view, auxiliary view and a cutting plane of: * Die vooraansig, hulpaansig en 'n snyvlak A-A van:
QUESTION A: A right regular pentagonal prism. VRAAG A: 'n Regte reëlmatige vyfkantige prisma. QUESTION A: A right regular pentagonal pyramid. VRAAG A: 'n Regte reëlmatige vyfkantige piramide.
QUESTION B: A right regular hexagonal prism. VRAAG B: 'n Regte reëlmatige seskantige prisma. QUESTION B: A right regular hexagonal pyramid. VRAAG B: 'n Regte reëlmatige seskantige piramide.
A X2 A 3
2 2 2
3 3 T
2 2 X 4 X
1 1 1
3 3
4 4 2 T 5 T
1 5
NC X2 NC
1 Y
5 1 A
4 4
3
5 5 NC 2 A NC
Y1 Y 1 X1 10 1 2 10
1 3 1
3
5 5 5
4 4 4
Y1 5 1 X1
5 2
2 5
T
2
4
4 3 4 3
Y2 Y2 3
B 3 B 5
X 2 4 4 6
X2 T
3 2 2/3
1 5 X
A 3 1
4 1 1/4 6
T 2 T
3 2 A
2/3 5/6
NC
Y X2 NC
5 6 Y A
4 1 1/4
NC NC
5 6 10 A 10
5/6 5 6 1 6
Y1 X1 1/5
1 1 4 2
2/4
Y1 3 3 X1
2 2 6 2 1
6
5 T 3 6
3 3 5
4 4
Y2 4 5 Y2
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: SOLIDS / VASTE LIGGAME
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
A
A
QUESTION: VRAAG: QUESTION: VRAAG:
Given: Gegee: Given: Gegee: 45°
* The front view and top view of a right regular * Die vooraansig en bo-aansig van 'n * The front view and top view of a right regular * Die vooraansig en bo-aansig van 'n
78
74
triangular pyramid. regte reëlmatige driehoekige piramide. square pyramid. regte reëlmatige vierkantige piramide.
A
50
* A cutting plane A-A. * 'n Snyvlak A-A. * A cutting plane A-A. * 'n Snyvlak A-A.
35
Instructions: Instruksies: 60° Instructions: Instruksies:
Draw to scale 1 : 1: Teken volgens skaal 1 : 1: Draw to scale 1 : 1: Teken volgens skaal 1 : 1: X Y
1. A sectional top view. 1. 'n Deursnee bo-aansig. XA Y 1. A sectional top view. 1. 'n Deursnee bo-aansig.
2. A sectional left view. 2. 'n Deursnee linkeraansig. 2. A sectional left view. 2. 'n Deursnee linkeraansig.
3. The true shape of the cut surface. 3. Die ware vorm van die gesnyde oppervlak. 3. The true shape of the cut surface. 3. Die ware vorm van die gesnyde oppervlak.
* Show ALL necessary construction. * Toon ALLE nodige konstruksies. * Show ALL necessary construction. * Toon ALLE nodige konstruksies.
55
* No hidden detail is required. * Geen verborge besonderhede word verlang nie. * No hidden detail is required. * Geen verborge besonderhede word verlang nie.
38
X1 X2 X1
T T T T
X2
NC NC
A A
NC NC
10 Y2 10
Y2
1 3 2 12 3
X A Y 1 42 3 2 13 4
X Y
1 2 2
T
1 3
3
Y1
4
Y1
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: SOLIDS / VASTE LIGGAME
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: VRAAG: QUESTION: VRAAG: A
A
Given: Gegee: Given: Gegee:
* The front view and top view of a right regular * Die vooraansig en bo-aansig van 'n * The front view and top view of a right regular * Die vooraansig en bo-aansig van 'n
79
82
pentagonal pyramid. regte reëlmatige vyfkantige piramide. hexagonal pyramid. regte reëlmatige seskantige piramide.
* A cutting plane A-A. * 'n Snyvlak A-A. * A cutting plane A-A. * 'n Snyvlak A-A. 45°
35
A
20
Instructions: Instruksies: Instructions: Instruksies:
Draw to scale 1 : 1: Teken volgens skaal 1 : 1: 60° Draw to scale 1 : 1: Teken volgens skaal 1 : 1:
1. A sectional top view. 1. 'n Deursnee bo-aansig. 1. A sectional top view. 1. 'n Deursnee bo-aansig. X Y
X Y
2. A sectional left view. 2. 'n Deursnee linkeraansig. A 2. A sectional left view. 2. 'n Deursnee linkeraansig.
3. The true shape of the cut surface. 3. Die ware vorm van die gesnyde oppervlak. 3. The true shape of the cut surface. 3. Die ware vorm van die gesnyde oppervlak.
* Show ALL necessary construction. * Toon ALLE nodige konstruksies. * Show ALL necessary construction. * Toon ALLE nodige konstruksies.
32
* No hidden detail is required. * Geen verborge besonderhede word verlang nie. * No hidden detail is required. * Geen verborge besonderhede word verlang nie.
28
X1
T T X1
T T
NC NC
A A
NC NC
10 10
12 53 4 3 2 4 1 5 1 62 53 4 23 14 65
X Y X Y
A 3 2 3
T 4 T
1 4
6 5
5 Y1
Y1
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: SOLIDS / VASTE LIGGAME
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: SOLIDS VRAAG: VASTE LIGGAME
Given: Gegee:
The front view and auxiliary view of a right regular Die vooraansig en hulpaansig van 'n regte reëlmatige
hexagonal pyramid. seskantige piramide.
Instructions: Instruksies:
Draw, to a scale 1 : 1, the following views of the solid: Teken die volgende aansigte van die vaste liggaam,
* The sectional top view volgens skaal 1 : 1:
* The left view, show ALL hidden detail * Die deursnee-boansig
* The sectional right view * Die linkeraansig, toon ALLE verborge besonderhede
* The true shape of the cut surface * Die deursnee-regteraansig
* Die ware vorm van die gesnyde oppervlak
NOTE: X4
Show ALL necessary construction. LET WEL:
Toon ALLE nodige konstruksies.
Y4
X3 X2
T T T
5 6 A 6 5
X 5/6
1/4
6 2/3 A
4 1 1 4
4/1
5 1
T
3 2 3/2 2 3
X1 Y Y1
4 2 1
3 6 2
3
5
NC
4
Y3 Y2
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: SOLIDS / VASTE LIGGAME
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: SOLIDS
Given:
* The front view and top view of a right regular hexagonal
Y2 X1 prism with a blind right regular square hole.
* A cutting plane A-A.
Instructions:
Draw, to scale 1 : 1, the following views of the solid:
A * The given front view
* The sectional top view
6 5/1 4/2 3 * The sectional left view
* The true shape of the section
* NO hidden detail are required.
Gegee:
* Die vooraansig en bo-aansig van 'n regte reëlmatige
seskantige prisma met 'n regte reëlmatige vierkantige
blinde gat.
* 'n Snyvlak A-A.
Instruksies:
Teken die volgende aansigte van die vaste liggaam,
volgens skaal 1 : 1:
* Die gegewe vooraansig
* 'n Deursnee bo-aansig
* 'n Deursnee linkeraansig
* 'n Ware vorm van die snit
* GEEN verborge besonderhede word verlang nie.
A
6 5/1 4/2 3
Y2 A Y1
X Y
60
1
80
2
55
A
6
3
28
32
5 4
NC
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: SOLIDS / VASTE LIGGAME
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: SOLIDS
X1 Q
Given:
The front view and top view of a right regular hexagonal prism
and a right regular pentagonal pyramid.
T D EC FB A CB DA T EF Spesifications:
* One base edge of the hexagonal prism is in contact with one
base edge of the pentagonal pyramid.
* Both solids are cut by a cutting plane QR.
Instructions:
Draw, to a scale 1 : 1, the following views of the TWO solids:
* The given front view
* The sectional top view
* The sectional right view, show ALL hidden detail.
Gegee:
Die vooraansig en boaansig van 'n regte reëlmatige seskantige
prisma en 'n regte reëlmatige vyfkantige piramide.
R Spesifikasies:
34 2D EC FB A CB DA 4 EF 3 2 * Een basissy van die seskantige prisma is in kontak met een
basissy van die vyfkantige piramide.
X 5 1 5 1 Y * Beide vaste liggame word deur 'n snyvlak QR gesny.
Instruksies:
Teken die volgende aansigte van die TWEE vaste liggame,
A volgens skaal 1 : 1:
* Die gegewe vooraansig
* Die deursnee-boaansig
* Die deursnee-regteraansig, toon ALLE verborge
B F besonderhede.
15
S Q
C E1 45°
72
D
5 2 R
T X Y
32
S
4
3 NC
Y1
32
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: SOLIDS / VASTE LIGGAME
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: SOLIDS
1 2 Given:
* The front view and an auxiliary view of a right regular
hexagonal prism, with a right regular square hole through the
X prism.
B * The position of point S on the answer sheet.
A X1 * A cutting plane A-A.
6 S 3 Instructions:
2 2
Draw, to a scale 1 : 1, the following views:
B B * A left view of the prism
C * A view showing the true shape of the section on cutting plane A-A
D 3/1 3 1 * NO hidden detail are required.
A
Y1 X
Y2 S
3 60°
A
3 4 C 30
A
X2 C
4 2 Y
B
50 60°
D B 2
5
5 D A 1
A 5 NC
1
5
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: SOLIDS / VASTE LIGGAME
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: SOLIDS
Given:
* The front view and auxiliary view of a right cone.
* A cutting plane A-A.
T X1 T X2 T Instructions:
Use the given views and draw:
* The right view
X * The sectional left view
* A view showing the true shape of the cut surface as
seen in the direction of arrow X
A NOTE:
Show ALL necessary construction.
Gegee:
5 4 3 5 4 3 4 5 * Die vooraansig en hulpaansig van 'n regte kegel.
* 'n Snyvlak A-A.
6 2 6 3 2 6
7 1 7 2 1 7 Instruksies:
1 Gebruik die volgende aansigte en teken:
8 12 12 12 8 * Die regteraansig
9 10 11 9 8 11 10 9 * Die deursnee-linkeraansig
Y1 1 0 11 Y2 Y * 'n Aansig wat die ware vorm van die gesnyde
oppervlak toon, soos gesien in die rigting van pyl X
LET WEL:
Toon ALLE nodige konstruksies.
2
X3 1 3
X
12 4
T
11 5
1 Y3
T
2 10 6
3 9 7
8
5
7 6
NC
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: SOLIDS / VASTE LIGGAME
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: SOLIDS
8 9
Given:
7 10 * The front view and auxiliary view of a cylinder.
* A cutting plane A-A.
Instructions:
6 11 Use the given views and draw:
* The top view
* The sectional left view
X
5 12 A 10 X2 NOTE:
10 Show ALL necessary construction.
11 9
11
9/
12
12
4 1 8
8/
VRAAG: VASTE LIGGAME
3 2 Gegee:
7
1 7
1/
* Die vooraansig en hulpaansig van 'n silinder.
* 'n Snyvlak A-A.
6
2/
2 6 Instruksies:
Y
5
4 3 5 * Die bo-aansig
4 * Die deursnee-linkeraansig
LET WEL:
Toon ALLE nodige konstruksies.
A
1 7
2 6
3 5
4
X1 Y1
1 1
2 12 12
3
11 11
4 10 10
5 9 9 NC
6 8 8
7 7 Y2
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: SOLIDS / VASTE LIGGAME
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
X1 QUESTION: INTERPENETRATION AND DEVELOPMENT
B A C BC A
Given:
* The front view and the top view of a right equilateral triangular
prism that has been shaped to fit around a right equilateral
2/3 triangular prism. The axes of both prisms lie in a common
vertical plane.
2 3
Instructions:
Draw, to scale 1 : 1, the following:
* The given top view
* The given front view
1 * The complete left view, clearly showing the curve of
interpenetration
1 * Develop the surfaces of both prisms
Gegee:
* Die vooraansig en die bo-aansig van 'n regte gelyksydige
driehoekige prisma wat gevorm is om rondom 'n regte
gelyksydige driehoekige prisma te pas. Die asse van beide
A B C A prismas lê in 'n gemeenskaplike vertikale vlak.
X Y Instruksies:
Teken, volgens skaal 1 : 1, die volgende:
* Die gegewe bo-aansig
B C * Die gegewe vooraansig
* Die volledige linkeraansig wat die deurdringingskurwe duidelik
toon
* Ontwikkel die oppervlakke van beide prismas.
A
44
17
2 1 3 1 2 3 1
Y1
84
X Y
NC
44
32
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: INTERPENETRATION / DEURDRINGING
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
X1 QUESTION: INTERPENETRATION AND DEVELOPMENT
B AC D C BD A
1 A Given:
1 * The front view and the top view of a right square prism that has
been shaped to fit around a right square prism. The axes of
both prisms lie in a common vertical plane.
* The position of point S on the drawing sheet.
4 2 4/2
Instructions:
Draw, to scale 1 : 1, the following:
* The given top view
3 D * The given front view
3 * The complete left view, clearly showing the curve of
interpenetration
* Develop the surfaces of both prisms
C Gegee:
* Die vooraansig en die bo-aansig van 'n regte vierkantige
X Y prisma wat gevorm is om rondom 'n regte vierkantige prisma te
pas. Die asse van beide prismas lê in 'n gemeenskaplike
vertikale vlak.
* Die posisie van punt S op die tekenvel.
C
Instruksies:
Teken, volgens skaal 1 : 1, die volgende:
* Die gegewe bo-aansig
S B * Die gegewe vooraansig
B D * Die volledige linkeraansig wat die deurdringingskurwe duidelik
toon
* Ontwikkel die oppervlakke van beide prismas
A
4 1/3 2
28
72
Y1
X Y
38
S
NC
32
1 2 3 4 1
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: INTERPENETRATION / DEURDRINGING
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
X1 QUESTION: INTERPENETRATION AND DEVELOPMENT
B AC D C BD A
A Given:
* The front view and the top view of a right regular hexagonal
1/2 prism that has been shaped to fit around a regular square
1 2 prism. The axes of both prisms lie in a common vertical plane.
* The position of point S on the drawing sheet.
Instructions:
6 3 6/3 Draw, to scale 1 : 1, the following:
* The given top view
* The given front view
D * The complete left view, clearly showing the curve of
5 4 interpenetration
5/4 * Develop the surfaces of both prisms
Gegee:
X Y * Die vooraansig en die bo-aansig van 'n regte reëlmatige
seskantige prisma wat gevorm is om rondom 'n reëlmatige
C vierkantige prisma te pas. Die asse van beide prismas lê in 'n
gemeenskaplike vertikale vlak.
C * Die posisie van punt S op die tekenvel.
Instruksies:
Teken, volgens skaal 1 : 1, die volgende:
* Die gegewe bo-aansig
S * Die gegewe vooraansig
B D * Die volledige linkeraansig wat die deurdringingskurwe duidelik
toon
* Ontwikkel die oppervlakke van beide prismas
B
Toon ALLE nodige konstruksies en voulyne.
11
66
6 1/5 2/4 3
Y1 A
X Y
42
S
38
NC
22
1 2 3 4 5 6 1
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: INTERPENETRATION / DEURDRINGING
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
X1 QUESTION: INTERPENETRATION AND DEVELOPMENT
HG AF BE CD FE GD HC AB
Given:
* The front view and the top view of a right regular hexagonal
1/2 prism that has been shaped to fit around a right regular
1 2 octagonal prism. The axes of both prisms lie in a common
vertical plane.
* The position of base edge AB on the drawing sheet.
6 3 6/3
Instructions:
Draw, to scale 1 : 1, the following:
5 4 * The given top view
5/4 * The given front view
* The complete left view, clearly showing the curve of
interpenetration
* Develop the surfaces of the hexagonal prism
Gegee:
* Die vooraansig en die bo-aansig van 'n regte reëlmatige
X Y seskantige prisma wat gevorm is om rondom 'n regte
reëlmatige seskantige prisma te pas. Die asse van beide
prismas lê in 'n gemeenskaplike vertikale vlak.
F E * Die posisie van basissy AB op die tekenvel.
Instruksies:
Teken, volgens skaal 1 : 1, die volgende:
* Die gegewe bo-aansig
G D * Die gegewe vooraansig
* Die volledige linkeraansig wat die deurdringingskurwe duidelik
toon
* Ontwikkel die oppervlakke van die seskantige prisma
10
A B
72
6 1/5 2/4 3
Y1 Y X
NC
A B
26
1 2 3 4 5 6 1
18
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: INTERPENETRATION / DEURDRINGING
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
C BD A QUESTION: INTERPENETRATION AND DEVELOPMENT
1/2 Given:
* The incomplete front view and the top view of a right regular
hexagonal prism that has been shaped to fit around a right
6/3 regular square prism. The axes of both prisms lie in a common
vertical plane.
* The position of point S on the drawing sheet.
5/4 Instructions:
Draw, to scale 1 : 1, the following:
* The given top view
* The complete front view, clearly showing the curve of
interpenetration
* Develop the surfaces of both prisms
72
36
18
X Y
22
38
S
NC
1 2 3 4 5 6 1
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: INTERPENETRATION / DEURDRINGING
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: INTERPENETRATION AND DEVELOPMENT
X1
C B D A E F D E C F B A Given:
* The incomplete front view and the top view of a right regular
1 square prism that has been shaped to fit around a right regular
1 hexagonal prism. The axes of both prisms lie in a common
vertical plane.
* The position of point S on the drawing sheet.
Instructions:
Draw, to scale 1 : 1, the following:
* The given top view
4 2 4/2 * The right view
* The complete front view, clearly showing the curve of
interpenetration
* Develop the surfaces of the square prism
X Y Gegee:
* Die onvolledige vooraansig en die bo-aansig van 'n regte
reëlmatige vierkantige prisma wat gevorm is om rondom 'n
regte reëlmatige seskantige prisma te pas. Die asse van beide
F 2 prismas lê in 'n gemeenskaplike vertikale vlak.
* Die posisie van punt S op die tekenvel.
E
Instruksies:
Teken, volgens skaal 1 : 1, die volgende:
C 4
38
Y1
68
34
45°
X Y
15°
S
NC
1 2 3 4 1
32
50
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: INTERPENETRATION / DEURDRINGING
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: INTERPENETRATION AND DEVELOPMENT
1 Given:
2 * The incomplete front view and the top view of a right regular
D C E B F A 1
square prism that has been shaped to fit around a right regular
hexagonal prism. The axes of both prisms lie in a common
vertical plane.
4 * The position of point S on the drawing sheet.
3
2/4 Instructions:
Draw, to scale 1 : 1, the following:
* The given top view
* The complete front view, clearly showing the curve of
interpenetration
* Develop the surfaces of the square prism
3 Show ALL hidden detail.
Show ALL necessary construction and fold lines.
Gegee:
* Die onvolledige vooraansig en die bo-aansig van 'n regte
reëlmatige vierkantige prisma wat gevorm is om rondom 'n
regte reëlmatige seskantige prisma te pas. Die asse van beide
X Y prismas lê in 'n gemeenskaplike vertikale vlak.
* Die posisie van punt S op die tekenvel.
E 2 Instruksies:
2 Teken, volgens skaal 1 : 1, die volgende:
F 1 2 3 4 1
* Die gegewe bo-aansig
* Die volledige vooraansig wat die deurdringingskurwe duidelik
toon
* Ontwikkel die oppervlakke van die vierkantige prisma
D S 1
3
1 3 Toon ALLE verborge besonderhede.
Toon ALLE nodige konstruksies en voulyne.
A
C 30°
4 4
B
68
38
12
X Y
32
28
S
NC
15°
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: INTERPENETRATION / DEURDRINGING
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
X1 QUESTION: INTERPENETRATION AND DEVELOPMENT
A DB C B AC D Given:
A * The incomplete front view and the top view of a right regular
square prism that has been shaped to fit around a right regular
1 square prism. The axes of both prisms lie in a common vertical
1 plane.
* The position of point S on the drawing sheet.
4 Instructions:
4 Draw, to scale 1 : 1, the following:
* The given top view
D * The left view
2 2 * The complete front view, clearly showing the curve of
interpenetration
* Develop the surfaces of both prisms
C Gegee:
X Y * Die onvolledige vooraansig en die bo-aansig van 'n regte
reëlmatige vierkantige prisma wat gevorm is om rondom 'n
regte reëlmatige vierkantige prisma te pas. Die asse van beide
prismas lê in 'n gemeenskaplike vertikale vlak.
4 B * Die posisie van punt S op die tekenvel.
Instruksies:
Teken, volgens skaal 1 : 1, die volgende:
* Die gegewe bo-aansig
3 S B * Die linkeraansig
A C * Die volledige vooraansig wat die deurdringingskurwe duidelik
toon
1 * Ontwikkel die oppervlakke van beide prismas
Y1 A 32
72
30°
X Y
□38
S
NC
1 2 3 4 1
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: INTERPENETRATION / DEURDRINGING
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
C D B A QUESTION: INTERPENETRATION AND DEVELOPMENT
A Given:
* The incomplete front view and the top view of a right regular
1 hexagonal prism that has been shaped to fit around a right
1 regular square prism. The axes of both prisms lie in a common
vertical plane.
6/2 6 2 * The position of point S on the drawing sheet.
Instructions:
Draw, to scale 1 : 1, the following:
* The given top view
B * The complete front view, clearly showing the curve of
5/3 5 3 interpenetration
* Develop the surfaces of both prisms
4
4 Show ALL hidden detail.
Show ALL necessary construction and fold lines.
X Y Gegee:
C * Die onvolledige vooraansig en die bo-aansig van 'n regte
reëlmatige seskantige prisma wat gevorm is om rondom 'n
regte reëlmatige vierkantige prisma te pas. Die asse van beide
D 2/3 prismas lê in 'n gemeenskaplike vertikale vlak.
2 3 * Die posisie van punt S op die tekenvel.
Instruksies:
S A Teken, volgens skaal 1 : 1, die volgende:
* Die gegewe bo-aansig
1/4 1 4 * Die volledige vooraansig wat die deurdringingskurwe duidelik
C D toon
* Ontwikkel die oppervlakke van beide prismas
70
X Y
24
40
S
30° NC
32
1 2 3 4 5 6 1
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: INTERPENETRATION / DEURDRINGING
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: INTERPENETRATION AND DEVELOPMENT
A B C D E F G H I J K L A
Given:
* The incomplete front view and the top view of a cylindrical pipe
A 1 B that has been shaped to fit around a cylindrical pipe A.
2/12 The axes of both pipes lie in a common vertical plane.
B * The position of point S on the drawing sheet.
3/11 Instructions:
Draw, to scale 1 : 1, the following:
* The given top view
* The complete front view, clearly showing the curve of
4/10 interpenetration
* Develop the surfaces of both pipes
Gegee:
* Die onvolledige vooraansig en die bo-aansig van 'n silindriese
pyp B wat gevorm is om rondom 'n silindriese pyp A te pas.
X Y Die asse van albei pype lê in 'n gemeenskaplike vertikale vlak.
* Die posisie van punt S op die tekenvel.
4 Instruksies:
J 3/5 Teken, volgens skaal 1 : 1, die volgende:
I K * Die gegewe bo-aansig
* Die volledige vooraansig wat die deurdringingskurwe duidelik
H L 2/6 toon
C = 3,14 x Ø * Ontwikkel die oppervlakke van beide pype
S
G A 1/7 = 3,14 x 52 Toon ALLE nodige konstruksies en berekeninge.
= 163,28 mm
F B 8/12 18
E C
D 9/11 A
10 B
74
X Y
1 2 3 4 5 6 7 8 9 10 11 12 1
Ø52
NC
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: INTERPENETRATION / DEURDRINGING
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
F G H QUESTION: INTERPENETRATION AND DEVELOPMENT
E I
D J Given:
A C K * The incomplete front view and the top view of a cylindrical pipe
B L A
B that has been shaped to fit around a cylindrical pipe A.
A The axes of both pipes lie in a common vertical plane.
* The position of point S on the drawing sheet.
1 2/12 Instructions:
Draw, to scale 1 : 1, the following:
B 3/11 * The given top view
* The complete front view, clearly showing the curve of
interpenetration
4/10 * Develop the surfaces of both pipes
Gegee:
* Die onvolledige vooraansig en die bo-aansig van 'n silindriese
X Y pyp B wat gevorm is om rondom 'n silindriese pyp A te pas.
Die asse van albei pype lê in 'n gemeenskaplike vertikale vlak.
* Die posisie van punt S op die tekenvel.
C = 3,14 x Ø
J 4 = 3,14 x 52
I K 3/5 Instruksies:
Teken, volgens skaal 1 : 1, die volgende:
= 163,28 mm * Die gegewe bo-aansig
H L 2/6 * Die volledige vooraansig wat die deurdringingskurwe duidelik
S toon
* Ontwikkel die oppervlakke van beide pype
G A 1/7
Toon ALLE nodige konstruksies en berekeninge.
F B 8/12
E C 9/11 4
D 10 3 5 9 10 11 18
1 2 6 7 8 12 1 A
8
B
74
8
X Y
Ø52
Ø38
C = 3,14 x Ø
= 3,14 x 38
= 119,32 mm NC
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: INTERPENETRATION / DEURDRINGING
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: INTERPENETRATION AND DEVELOPMENT
Given:
1/11 2/10 * The incomplete front view and the top view of a cylindrical pipe
B that has been shaped to fit around a cylindrical pipe A.
0 3/9 The axes of both pipes lie in a common vertical plane.
* The position of point S on the drawing sheet.
0 4/8
A B Instructions:
Draw, to scale 1 : 1, the following:
5/7 * The given top view
* The complete front view, clearly showing the curve of
interpenetration
6 * Develop the surfaces of both pipes
Gegee:
* Die onvolledige vooraansig en die bo-aansig van 'n silindriese
C E I K pyp B wat gevorm is om rondom 'n silindriese pyp A te pas.
Die asse van albei pype lê in 'n gemeenskaplike vertikale vlak.
B F H L * Die posisie van punt S op die tekenvel.
9 9 A G A
J 8/10 0 C = 3,14 x Ø Instruksies:
I K Teken, volgens skaal 1 : 1, die volgende:
Ø
3
42
6 45°
A B
7
8
70
56
9
10 45°
5
11 X Y
C = 3,14 x Ø 12
S
= 3,14 x 42
= 131,88 mm
Ø50
NC
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: INTERPENETRATION / DEURDRINGING
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
SEAM
LAS
QUESTION: DEVELOPMENT VRAAG: ONTWIKKELING
B
Given: Gegee:
* The front view and top view of a portion of a duct showing a * Die vooraansig en bo-aansig van 'n gedeelte van 'n kanaal wat
square-to-square transition piece. 'n vierkant-na-vierkant-oorgangstuk toon.
* Starting position of point A of the seam. * Beginposisie van punt A van die naat.
Instructions: Instruksies:
* Draw, to scale 1 : 1, the given front view and top * Teken, volgens skaal 1 : 1, die gegewe vooraansig en
view of the given portion of the duct.
* Develop the surface of the transition piece in the direction of
a bo-aansig van die gegewe gedeelte van die kanaal.
* Ontwikkel die oppervlak van die oorgangstuk in die rigting van
the arrow as shown on the top view. die pyl soos getoon op die bo-aansig.
* Make edge AB the seam. b G * Maak sy AB die naat.
Show ALL necessary construction and fold lines. Toon ALLE nodige konstruksies en voulyne.
A a b A a
b
A
H
a = 70mm
b = 82mm
65
F E
a
b
B
B X Y
X Y D
G E
b a
a
a
□ 30
□ 65
A b A
H F
b C
B
b A a
D
a b a
NC
B C
B
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: DEVELOPMENT / ONTWIKKELING
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: DEVELOPMENT VRAAG: ONTWIKKELING
Given:
* The front view and top view of a portion of a duct showing a
B Gegee:
* Die vooraansig en bo-aansig van 'n gedeelte van 'n kanaal wat
square-to-square transition piece. 'n vierkant-na-vierkant-oorgangstuk toon.
* Starting position of point A of the seam. * Beginposisie van punt A van die naat.
Instructions:
* Draw, to scale 1 : 1, the given front view and top
I Instruksies:
* Teken, volgens skaal 1 : 1, die gegewe vooraansig en
view of the given portion of the duct. bo-aansig van die gegewe gedeelte van die kanaal.
* Develop the surface of the transition piece in the direction of b * Ontwikkel die oppervlak van die oorgangstuk in die rigting van
the arrow as shown on the top view. die pyl soos getoon op die bo-aansig.
* Make edge AB the seam. a * Maak sy AB die naat.
Show ALL necessary construction and fold lines. Toon ALLE nodige konstruksies en voulyne.
a
b a A
A
a G A
H
a = 74mm
b = 66mm a
65
F
a B
B X Y
X Y D
I G a E
a a
□ 65
B A
a H a A
30
a
□
b a
B A F
b
a D a
C
a a NC
C
E
B
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: DEVELOPMENT / ONTWIKKELING
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: DEVELOPMENT VRAAG: ONTWIKKELING
Given: B Gegee:
* The front view and top view of a portion of a duct showing a * Die vooraansig en bo-aansig van 'n gedeelte van 'n kanaal wat
square-to-square transition piece. 'n vierkant-na-vierkant-oorgangstuk toon.
* Starting position of point A of the seam.
* The position of point S on the answer sheet.
F * Beginposisie van punt A van die naat.
* Die posisie van punt S op die antwoordblad.
Instructions: Instruksies:
* Draw, to scale 1 : 1, the given front view and top
view of the given portion of the duct.
a * Teken, volgens skaal 1 : 1, die gegewe vooraansig en
bo-aansig van die gegewe gedeelte van die kanaal.
* Develop the surface of the transition piece in the direction of c * Ontwikkel die oppervlak van die oorgangstuk in die rigting van
the arrow as shown on the top view. die pyl soos getoon op die bo-aansig.
* Make edge AB the seam. * Maak sy AB die naat.
Show ALL necessary construction and fold lines. b Toon ALLE nodige konstruksies en voulyne.
A
A b a
E
c
a = 66mm A
b = 76mm I
b
c = 71mm
65
a
H
c
B
X Y
G b
B D
X Y
F E B A
A S
□ 65
b c
c 60°
c □ 30
I b b
a
B A S
a
H
b C
G c
NC
c b
B
C D NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: DEVELOPMENT / ONTWIKKELING
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: DEVELOPMENT VRAAG: ONTWIKKELING
B
Given: Gegee:
* The front view and top view of a portion of a duct showing a * Die vooraansig en bo-aansig van 'n gedeelte van 'n kanaal wat
square-to-square transition piece. 'n vierkant-na-vierkant-oorgangstuk toon.
* Starting position of point A of the seam. * Beginposisie van punt A van die naat.
* The position of point S on the answer sheet. * Die posisie van punt S op die antwoordblad.
Instructions: Instruksies:
* Draw, to scale 1 : 1, the given front view and top * Teken, volgens skaal 1 : 1, die gegewe vooraansig en
view of the given portion of the duct. a bo-aansig van die gegewe gedeelte van die kanaal.
* Develop the surface of the transition piece in the direction of * Ontwikkel die oppervlak van die oorgangstuk in die rigting van
the arrow as shown on the top view. die pyl soos getoon op die bo-aansig.
* Make edge AB the seam. c * Maak sy AB die naat.
E
Show ALL necessary construction and fold lines. Toon ALLE nodige konstruksies en voulyne.
A d
ed a bc A
□ 28
a = 72mm A
F
b = 84mm
e
c = 86mm
65
d = 69mm d D
e = 81mm G
B
X Y
B H c
12
X Y
E D a S
A
□ 65
d e d A
F G
b C
S B
c
A H a
c
a a
NC
b
B C B NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: DEVELOPMENT / ONTWIKKELING
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: DEVELOPMENT
B VRAAG: ONTWIKKELING
Given: Gegee:
* The front view and top view of a portion of a duct showing a * Die vooraansig en bo-aansig van 'n gedeelte van 'n kanaal wat
square-to-square transition piece. 'n vierkant-na-vierkant-oorgangstuk toon.
* Starting position of point A of the seam. * Beginposisie van punt A van die naat.
* The position of point S on the answer sheet. * Die posisie van punt S op die antwoordblad.
Instructions:
* Draw, to scale 1 : 1, the given front view and top
a Instruksies:
* Teken, volgens skaal 1 : 1, die gegewe vooraansig en
view of the given portion of the duct. bo-aansig van die gegewe gedeelte van die kanaal.
* Develop the surface of the transition piece in the direction of * Ontwikkel die oppervlak van die oorgangstuk in die rigting van
the arrow as shown on the top view. c die pyl soos getoon op die bo-aansig.
* Make edge AB the seam. * Maak sy AB die naat.
E
Show ALL necessary construction and fold lines. Toon ALLE nodige konstruksies en voulyne.
A A d
c e a b
□ 28
A
a = 77mm F
b = 88mm e
d d
c = 94mm
65
d = 68mm G d
D
e = 80mm
B
X Y
B H
c S
X Y
E d d D A
F G A a
□ 65
S
c A H c b C B
a a a
b
NC
B C
B NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: DEVELOPMENT / ONTWIKKELING
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: DEVELOPMENT VRAAG: ONTWIKKELING
Given: Gegee:
* The front view and top view of a portion of a duct showing a * Die vooraansig en bo-aansig van 'n gedeelte van 'n kanaal wat
rectangular-to-square transition piece. 'n reghoekige-na-vierkant-oorgangstuk toon.
* Starting position of point A of the seam. * Beginposisie van punt A van die naat.
* The position of point S on the answer sheet.
B * Die posisie van punt S op die antwoordblad.
Instructions: Instruksies:
* Draw, to scale 1 : 1, the given front view and top * Teken, volgens skaal 1 : 1, die gegewe vooraansig en
view of the given portion of the duct. bo-aansig van die gegewe gedeelte van die kanaal.
* Develop the surface of the transition piece in the direction of * Ontwikkel die oppervlak van die oorgangstuk in die rigting van
the arrow as shown on the top view. a die pyl soos getoon op die bo-aansig.
* Make edge AB the seam. * Maak sy AB die naat.
A
A E A
dc ab d
H a
a = 65mm
62
b = 85mm
c = 78mm G
d = 68mm B
b X Y
F
c
26
□
B A D S
56
X Y A
D E c
b 75
B
b a
G d
c a
S
F H
C
c A d
b a NC
B
C B
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: DEVELOPMENT / ONTWIKKELING
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: DEVELOPMENT VRAAG: ONTWIKKELING
Given: Gegee:
* The front view and top view of a square-to-irregular square * Die vooraansig en bo-aansig van 'n gedeelte van 'n kanaal wat
transition piece. 'n vierkant-na-onreëlmatige vierkantige-oorgangstuk toon.
* Starting position of point A of the seam. * Beginposisie van punt A van die naat.
* The position of point S on the answer sheet. * Die posisie van punt S op die antwoordblad.
Instructions: Instruksies:
* Draw, to scale 1 : 1, the given front view and top * Teken, volgens skaal 1 : 1, die gegewe vooraansig en
view of the given portion of the duct. bo-aansig van die gegewe gedeelte van die kanaal.
* Develop the surface of the transition piece in the direction of * Ontwikkel die oppervlak van die oorgangstuk in die rigting van
the arrow as shown on the top view. die pyl soos getoon op die bo-aansig.
* Make edge AB the seam. * Maak sy AB die naat.
Show ALL necessary construction and fold lines. Toon ALLE nodige konstruksies en voulyne.
e B
d a = 51 mm
b = 58 mm A
c c c = 69 mm
a d = 80 mm e b
75
b e = 27 mm I
H c
50
e
F
X Y
c
24
e
□
d
D
G S
□ 54
B A
X Y e d
A
I G
c c c
b H d c
e e
S a b E
B A F
a
e e
b D d
NC
c c
C E B C
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: DEVELOPMENT / ONTWIKKELING
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: DEVELOPMENT VRAAG: ONTWIKKELING
Given: Gegee:
* The front view and top view of a square-to-irregular square * Die vooraansig en bo-aansig van 'n gedeelte van 'n kanaal wat
transition piece. 'n vierkant-na-onreëlmatige vierkantige-oorgangstuk toon.
* Starting position of point A of the seam. * Beginposisie van punt A van die naat.
* The position of point S on the answer sheet. * Die posisie van punt S op die antwoordblad.
Instructions: Instruksies:
* Draw, to scale 1 : 1, the given front view and top * Teken, volgens skaal 1 : 1, die gegewe vooraansig en
view of the given portion of the duct. bo-aansig van die gegewe gedeelte van die kanaal.
* Develop the surface of the transition piece in the direction of * Ontwikkel die oppervlak van die oorgangstuk in die rigting van
the arrow as shown on the top view. die pyl soos getoon op die bo-aansig.
* Make edge AB the seam. B * Maak sy AB die naat.
Show ALL necessary construction and fold lines. Toon ALLE nodige konstruksies en voulyne.
A
a = 58 mm a
b = 66 mm d e c F
c = 26 mm 60° 45°
d = 29 mm I b
e = 82 mm d
c b
77
a H
b
50
A
d e
G E X Y
e
24
c
□
A
b
□ 54
B A
B
X Y b
a
F E D
b b
a I e
c d
S B C
B A H
c d
NC
a G e
b b
NC
C D
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: DEVELOPMENT / ONTWIKKELING
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: DEVELOPMENT VRAAG: ONTWIKKELING
Given: Gegee:
* The front view and top view of a hexagon-to-irregular hexagon * Die vooraansig en bo-aansig van 'n gedeelte van 'n kanaal wat
transition piece. 'n seskant-na-onreëlmatige seskantige oorgangstuk toon.
* Starting position of point A of the seam. * Beginposisie van punt A van die naat.
* The position of point S on the answer sheet. * Die posisie van punt S op die antwoordblad.
Instructions: Instruksies:
* Draw, to scale 1 : 1, the given front view and top * Teken, volgens skaal 1 : 1, die gegewe vooraansig en
view of the given portion of the duct. bo-aansig van die gegewe gedeelte van die kanaal.
* Develop the surface of the transition piece in the direction of * Ontwikkel die oppervlak van die oorgangstuk in die rigting van
the arrow as shown on the top view. die pyl soos getoon op die bo-aansig.
* Make edge AB the seam. * Maak sy AB die naat.
Show ALL necessary construction and fold lines. Toon ALLE nodige konstruksies en voulyne.
B
a
A
c
i G
h g b
77
ef a = 18 mm d
b = 26 mm
46
A
L
c b d c = 40 mm
j e f
17
A d = 31 mm
e = 22 mm K g B
F X Y
a f = 50 mm h
g = 45 mm J i
h = 14 mm h
B
X Y
i = 54 mm I j S
B A
j = 50 mm i
G F
e E
d f
g H g
c L e i f 32
K h b
b
a S j A D
B A J E d
b c
c I h i a
H e
g C
d f B
NC
C D
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: DEVELOPMENT / ONTWIKKELING
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: DEVELOPMENT
A Given:
a b c B * The front view and top view of a square-to-round transition
piece.
Instructions:
F * Make edge AB the seam.
* Develop the surface of the transition piece.
Gegee:
* Die vooraansig en bo-aansig van 'n vierkant-tot-ronde
oorgangstuk.
A Instruksies:
* Maak sy AB die naat.
B c
E * Ontwikkel die oppervlak van die oorgangstuk.
X Y c
Toon ALLE nodige konstruksies en voulyne.
F E b
c
c
b c b c b
C = 3,14 x Ø
c c c
a = 3,14 x 35
B A b
c = 109,9 mm
c c
b c b c b
c D
c
A
C D
b
a
C
NC
B
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: DEVELOPMENT / ONTWIKKELING
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
TIGHTEN
RIGHTY-TIGHTY
LOOSEN
LEFTY-LOOSEY
VASDRAAI
RIGHTY-TIGHTY
LOSDRAAI
LEFTY-LOOSEY
QUESTION: LOCI (AUGER) 6 QUESTION: LOCI (AUGER)
7 5
Given: Given:
* The front view and top view of a solid shaft. * The front view and top view of a solid shaft.
* A reference point, labelled O, to help with the placement * A reference point, labelled O, to help with the placement
9 of the answer. 8 4 of the answer.
10 8 Specifications: Specifications:
* The pitch (ONE full turn) is 60 mm. * The pitch (ONE full turn) is 48 mm.
* The outer diameter of the auger is Ø80. * The outer diameter of the auger is Ø80.
11 7 Instructions: 9 3 Instructions:
* Starting at point A, draw, to scale 1:1, TWO turns of a O * Starting at point A, draw, to scale 1:1, THREE turns of a
left-hand single-line auger. right-hand single-line auger.
* Show ALL necessary construction. * Show ALL necessary construction.
* NO hidden detail is required. * NO hidden detail is required.
0
A 6 10 2
12 O VRAAG: LOKUSSE (AWEGAAR) VRAAG: LOKUSSE (AWEGAAR)
Gegee: Gegee:
* Die vooraansig en bo-aansig van 'n soliede as. * Die vooraansig en bo-aansig van 'n soliede as.
* 'n Verwysingspunt, gemerk O, om te help met die plasing 11 1 * 'n Verwysingspunt, gemerk O, om te help met die plasing
1 5 van die antwoord. A 0 van die antwoord.
12
Spesifikasies: 0/12 Spesifikasies:
* Die steek (EEN volle draai is 60 mm). 11 * Die steek (EEN volle draai is 48 mm).
2 4 * Die buitediameter van die awegaar is Ø80. 10 * Die buitediameter van die awegaar is Ø80.
9
3 Instruksies: 8 Instruksies:
0 * Deur te begin by punt A, teken, volgens skaal 1:1, TWEE 7 * Deur te begin by punt A, teken, volgens skaal 1:1, DRIE
A
12 draaie van 'n linkerhandse enkellyn-awegaar. 6 draaie van 'n regterhandse enkellyn-awegaar.
1
* Toon ALLE konstruksies. 5 * Toon ALLE konstruksies.
2 * GEEN verborge besonderhede word verlang nie. 4 * GEEN verborge besonderhede word verlang nie.
3 3
4 2
1
5
0/12
6 11
O
7 A 10
O
8 9
8 Ø80
9
7
10 A
Ø80 6
11 A 5
0/12 4
3
1
2
2 1
3 0/12
11
120
144
4
10
5
9
6 8
7 7
8 6
5
9 NC NC
4
10 3 A
11 2
0/12 1
0/12
NC A NC
10 10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: LOCI (HELIX) / LOKUSSE (HELIKS)
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: LOCI (AUGER) QUESTION: LOCI (AUGER)
Given: Given:
* The front view and top view of a solid shaft. 9 * The front view and top view of a solid shaft.
* A reference point, labelled O, to help with the placement * A reference point, labelled O, to help with the placement
of the answer. 10 8 of the answer.
9 Specifications: Specifications:
* The pitch (ONE full turn) is 60 mm. * The pitch (ONE full turn) is 48 mm.
8 10 * The outer diameter of the auger is Ø80. 11 7 * The outer diameter of the auger is Ø80.
Instructions: Instructions:
* Starting at point A, draw, to scale 1:1, ONE AND A HALF * Starting at point A, draw, to scale 1:1, TWO AND A HALF
7 11 turns of a left-hand single-line auger. turns of a right-hand single-line auger.
* Show ALL necessary construction. 0 * Show ALL necessary construction.
* NO hidden detail is required. A 6
12 O * NO hidden detail is required.
120
3
7
90
2 6
1 5
0/12 4
A 3
NC 2 NC
A 1 A
0
A
12
NC NC
10 10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: LOCI (HELIX) / LOKUSSE (HELIKS)
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: LOCI (COIL SPRING) QUESTION: LOCI (HELIX)
Given: 3 Given:
* The top view of a coil spring with PR The top view of a round coil spring.
indicating the starting position.
2 4
* The position of centre point O on the Specifications:
9 * Left-handed
drawing sheet.
8 10 * Pitch = 60 mm
1 5 * ONE AND A HALF revolutions, start at the
Specifications:
* Pitch = 100mm left bottom
* Outer diameter = Ø80 * Show ALL necessary construction
7 11
* Inner diameter = Ø48 * NO hidden detail is required
* Spring profile = Ø16
* Direction = Right-handed 6 Instructions:
0
* Draw, to scale 1 : 1, the front view of a
P 0 R 12
6 round coil spring.
12 Instructions:
O * Draw, to scale 1 : 1, the given top view
and front view for ONE turn of the coil
spring and start at the top right. VRAAG: LOKUSSE (HELIKS)
5 1 * Show ALL necessary construction.
11 7
* NO hidden detail is required. Gegee:
Die bo-aansig van 'n ronde veer.
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: LOCI (HELIX) / LOKUSSE (HELIKS)
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: LOCI (HELIX) QUESTION: LOCI (HELIX)
Given: Given:
* The top view of an auger showing the * The top view of an auger showing the
6 shaft and the outer diameter with starting shaft and the outer diameter with starting
point AB point AB
7 5 * The centre line of the front view. 3 * The centre line of the front view.
4
Specifications: Specifications:
* One revolution with a pitch of 100 mm. * TWO revolutions with a pitch of 48 mm.
* Right-handed. * Left-handed.
8 4
* Start on the bottom and end at the top. * Start on the top and end at the bottom.
5 1
Instructions: Instructions:
Use the given view and complete the front Use the given view and complete the front
view of the auger by starting at AB at the view of the auger by starting at AB on top.
bottom.
9 3 B A0 Note:
6
Note: 12 * ALL construction must be shown.
* ALL construction must be shown. * NO hidden detail is required.
B * NO hidden detail is required.
NC
10 10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: LOCI (HELIX) / LOKUSSE (HELIKS)
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: LOCI (HELIX) QUESTION: LOCI (HELIX)
3
Given: Given:
2 4
* The top view of an auger showing the 6 * The top view of an auger showing the
shaft and the outer diameter with starting shaft and the outer diameter with starting
5 7
point AB. point AB.
* The centre line of the front view. * The centre line of the front view.
1 5
Specifications: Specifications:
* TWO revolutions with a pitch of 60 mm. 4 8 * ONE AND A HALF revolutions with a pitch
* Right-handed. of 72 mm.
* Start on the top and end at the bottom. * Left-handed.
* Start at the bottom and end at the top.
0A B Instructions:
6
12 Use the given view and complete the front Instructions:
view of the auger by starting at AB on top. Use the given view and complete the front
3 9
view of the auger by starting at AB in the
Note: middle at the bottom.
* ALL construction must be shown.
* NO hidden detail is required. B Note:
11 7 * ALL construction must be shown.
* NO hidden detail is required.
2 10
VRAAG: LOKUS (HELIKS)
0/12
END / EINDIG!
NC
10 10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: LOCI (HELIX) / LOKUSSE (HELIKS)
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: LOCI (SQUARE SPRING) QUESTION: LOCI (SQUARE SPRING)
3
Given: Given:
* The top view of a square spring.
2 4 * The top view of a square spring.
* The position of centre point O on the * The position of centre point O on the
answer sheet. answer sheet.
1 5
Specifications: Specifications:
9 * ONE AND A HALF revolutions with a pitch * TWO revolutions with a pitch
of 48 mm of 48 mm
8 10 * Spring profile = 12 x 12 mm * Spring profile = 16 x 16 mm
* Left-handed 0 * Right-handed
* Start on the right bottom 6 * Start on the top left
12 O
7 11 Instructions: Instructions:
* Draw, to scale 1 : 1, the given top view and * Draw, to scale 1 : 1, the given top view and
front view of the left-handed square spring. front view of the right-handed square
* Show ALL necessary construction. 11 7 spring.
* NO hidden detail is required. * Show ALL necessary construction.
0
6 * NO hidden detail is required.
O 12
10 8
VRAAG: LOKUS (VIERKANTIGE VEER) 9 VRAAG: LOKUS (VIERKANTIGE VEER)
5 1 Gegee: Gegee:
* Die bo-aansig van 'n veerkantige veer. START * Die bo-aansig van 'n veerkantige veer.
* Die posisie van middelpunt O op die BEGIN! * Die posisie van middelpunt O op die
tekenvel. tekenvel.
4 2 0/12
1
3 Spesifikasies: Spesifikasies:
END / EINDIG! 2
* EEN EN 'N HALWE rewolusies met 'n * TWEE rewolusies met 'n
3
steek van 48 mm steek van 48 mm
* Veerprofiel = 12 x 12 mm
4 * Veerprofiel = 16 x 16 mm
* Linkerhands 5 * Regterhands
6 * Begin regs onder 6 * Begin links bo
5 7
4 Instruksies: 8 Instruksies:
3 * Teken, volgens skaal 1 : 1, die gegewe 9 * Teken, volgens skaal 1 : 1, die gegewe
2 bo-aansig en vooraansig van die linker- 10 bo-aansig en vooraansig van die regter-
1 handse vierkantige veer. 11 handse vierkantige veer.
0/12 * Toon ALLE nodige konstruksies. 0/12 * Toon ALLE nodige konstruksies.
11 * GEEN verborge besonderhede word 1 * GEEN verborge besonderhede word
10 verlang nie. 2 verlang nie.
9 3
8 4
7 Ø50 5 Ø42
6 6
5 7
4 8
3 9
END
2 EINDIG!10
1 O 11 O
0/12 0/12
START / BEGIN!
* From bottom to top number in the * From top to bottom number in the
Ø74 Ø74
opposite direction as the direction of same direction as the direction of NC
rotation. rotation.
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: LOCI (HELIX) / LOKUSSE (HELIKS)
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
1 2 3 4 5 QUESTION: LOCI (SQUARE THREAD) 6 QUESTION: LOCI (SQUARE THREAD)
0 1 2 3 4 5 Given: Given:
6 * The incomplete front view of a single-start 7 5 * The incomplete front view of a single-start
12
square thread showing the starting. square thread.
position A at the centre on the left of the * The centre line and the starting position AB
shaft. at the centre front of the shaft as a
* The centre line of the front view and one 8 4 reference on the drawing sheet.
half of the top view showing the shaft and Specifications:
the outer diameter . * ONE AND A HALF revolutions with a pitch
11 7 Specifications: of 60 mm
* ONE revolution with a pitch of 120 mm * Right-handed
* Right-handed * Outside diameter
7 3
* Outside diameter = 100 mm * Core diameter = 80 mm
* Core diameter = 60 mm Instructions: = 40 mm
10 8 Instructions: * Draw, to scale 1 : 1, the top view and
* Draw, to scale 1 : 1, the top view and complete front view of the right-handed
9 complete front view of the right-handed square thread.
square thead. 10 2 * Show ALL necessary construction.
* Show ALL necessary construction. * NO hidden detail is required.
* NO hidden detail is required.
11 1
0/12 VRAAG: LOKUS (VIERKANTIGE 0/12 VRAAG: LOKUS (VIERKANTIGE
START AB
BEGIN! SKROEFDRAAD) SKROEFDRAAD)
Gegee: 6 Gegee:
1 * Die onvolledige vooraansig van 'n enkel- 5 * Die onvolledige vooraansig van 'n enkel-
begin-vierkantige skroefdraad en die END begin-vierkantige skroefdraad.
4 EINDIG!
2 begin-posisie A aan die middel-linkerkant * Die senterlyn en die beginposisie AB by
van die as toon. 3 die middel-voorkant van die as as
* Die senterlyn van die vooraansig en die 2 verwysing op die tekenvel.
3 een helfte van die bo- aansig wat die as en Spesifikasies:
1
die buite-diameter toon. * EEN EN 'N HALWE rewolusies met 'n
Spesifikasies: 0/12 steek van 60 mm
4
* EEN rewolusie met 'n steek van 120 mm 11 * Regterhands
* Regterhands 10 * Buitediameter = 80 mm
5 * Buitediameter = 100 mm * Kerndiameter = 40 mm
9
* Kerndiameter = 60 mm Instruksies:
Instruksies: 8 * Teken, volgens skaal 1 : 1, bo-aansig en
6
* Teken, volgens skaal 1 : 1, bo-aansig en 7 volledige vooraansig van die regter-handse
volledige vooraansig van die regter- 6 vierkantige skroefdraad.
7 handse vierkantige skroefdraad. * Toon ALLE nodige konstruksies.
* Toon ALLE nodige konstruksies. 5 * GEEN verborge besonderhede word
* GEEN verborge besonderhede word 4 verlang nie.
8 verlang nie. 3
2 Ø40
9
Ø40 1
0/12
A
20
10 A
START
BEGIN!
90
11
B
120
0/12
END
EINDIG!
* From top to bottom number in the * From bottom to top number in the A
START
same direction as the direction of opposite direction as the direction of NC
20
BEGIN! B
rotation. rotation.
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: LOCI (HELIX) / LOKUSSE (HELIKS)
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: LOCI (HELIX) VRAAG: LOKUS (HELIKS)
Given: 9 Gegee:
* The profile of a single-start right-hand square thread in the * Die profiel van 'n enkelvoudige regterhandse vierkantige
starting position. 10 8 skroefdraad in die beginposisie.
* The complete core. * Die volledige kern.
* The position of O on the drawing sheet. * Die posisie van O op die tekenvel.
Instructions: 11 7 Instruksies:
* Draw to scale 1:1, ONE AND A HALF turns of the single-start * Teken, volgens skaal 1:1, EEN EN 'N HALWE draaie van die
right-hand square thread. enkelvoudige regterhandse vierkantige skroefdraad.
* Show ALL necessary construction. * Toon ALLE nodige konstruksies.
* NO hidden detail is required. * GEEN verborge besonderhede word verlang nie.
0
6
12
Ø42
1 5
2 4
3
24
6
5
24
4
3
2
1 O
0/12
11
10
9 RUBRIC CORRECTNESS / RUBRIEK KORREKTHEID
8
OUTSTANDING / UITSTEKEND
7
6 VERY GOOD / BAIE GOED
5 GOOD / GOED
4
3
2
1
0/12 VERY BAD / BAIE SWAK
NOTE: O NON COMPLIANCE / NIE VOLDOEN NC
H = W = ½ PITCH * From bottom to top number in the
QUALITY & NEATNESS / KWALITEIT & NETHEID
opposite direction as the direction of OUTSTANDING / UITSTEKEND
LET WEL: rotation.
H = W = ½ STEEK VERY BAD / BAIE SWAK
* Van onder na bo nommer teenoor-
gestelde rigting as die draairigting. NON COMPLIANCE / NIE VOLDOEN NC
TOTAL / TOTAAL 10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: LOCI (HELIX) / LOKUSSE (HELIKS)
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
POSITIONING OF THE DISPLACEMENT GRAPH IN RELATION TO THE CAM FOLLOWER
POSITIONERING VAN DIE VERPLASINGSGRAFIEK TEN OPSIGTE VAN DIE NOKVOLGER
360°- 0°
0°- 360°
WEDGE-ENDED /
ROLLER-ENDED
(KNIFE-EGDE)
FOLLOWER
FOLLOWER
WIGVORMIGE / WIGVORMIGE
(MESPUNT) VOLGER VOLGER
30°
30°
0° 60° 120° 180° 240° 300° 360° 0° 60° 120° 180° 240° 300° 360°
DISPLACEMENT GRAPH DISPLACEMENT GRAPH
SCALE 8 mm = 30° SCALE 8 mm = 30°
VERPLASINGSGRAFIEK VERPLASINGSGRAFIEK
SKAAL 8 mm = 30° SKAAL 8 mm = 30°
Note:
The follower always moves in the opposite direction as the rotation direction!
Let wel:
Die volger beweeg altyd in die teenoogestelde rigting as die draairigting!
The bottom of the displacement graph is always in line with the point of the wedge-ended follower. The bottom of the displacement graph is always in line with the centre of the roller-ended follower.
Die onderkant van die verplasingsgrafiek is altyd in lyn met die punt van die wigvormige volger. Die onderkant van die verplasingsgrafiek is altyd in lyn met die middelpunt van die rollervormige volger.
DIFFERENT MOVEMENTS OF THE FOLLOWER / VERSKILLENDE BEWEGINGS VAN DIE VOLGER
UNIFORM MOTION UNIFORM ACCELERATION & RETARDATION UNIFORM ACCELERATION & RETARDATION
EENVORMIGE BEWEGING EENVORMIGE VERSNELLING & VERTRAGING EENVORMIGE VERSNELLING & VERTRAGING
150° 210° 180°
RISE
STYG 120° 240° 210°
FALL
90° 270° 240°
DAAL
RISE DWELL 270°
STYG RUS 60° 300°
300°
30° 330° 330°
0° 60° 120° 180° 240° 300° 360°
DISPLACEMENT GRAPH VERPLASINGSGRAFIEK 0° 60° 120° 180° 240° 300° 360°
SCALE 12 mm = 30° SKAAL 12 mm = 30° DISPLACEMENT GRAPH VERPLASINGSGRAFIEK
SCALE 12 mm = 30° SKAAL 12 mm = 30°
SIMPLE HARMONIC SIMPLE HARMONIC UNIFORM MOTION SIMPLE HARMONIC UNIFORM ACCELERATION & RETARDATION
EENVOUDIG HARMONIESE EENVOUDIG HARMONIESE EENVORMIGE BEWEGING EENVOUDIG HARMONIESE EENVORMIGE VERSNELLING & VERTRAGING
180° 180° 180°
150° 210° 165°
180°
120° 240° 150° 210°
210°
RISE FALL RISE
240°
90° STYG DAAL 270° 135° STYG 240°
FALL
270°
60° 300° 120° DAAL 270°
300° 300°
30° 330° 105°
0° 60° 120° 180° 240° 300° 360° 90° DWELL
RUS
DISPLACEMENT GRAPH VERPLASINGSGRAFIEK RISE
330° 330°
SCALE 12 mm = 30° SKAAL 12 mm = 30° STYG
105°
135°
165°
0° 60° 120° 180° 240° 300° 360°/0°
DISPLACEMENT GRAPH VERPLASINGSGRAFIEK
SCALE 130 mm = 360° SKAAL 130 mm = 360°
QUESTION: LOCI (CAM)
Instructions: RISE
0° 30° 60° 90° 120° 150° 180° 210° 240° 270° 300° 330° 360°
* Draw, to scale 1 : 1 and in the correct position, the given STYG
follower so that it will reciprocate along the vertical centre DISPLACEMENT GRAPH
SCALE 10 mm = 30°
line of the camshaft.
* Project and draw the cam profile from the given VERPLASINGSGRAFIEK
displacement graph. SKAAL 10 mm = 30°
* Show the centre lines and the direction of rotation on the 270° 90°
cam profile.
* Show ALL necessary construction. FALL
DAAL
VRAAG: LOKUSSE (NOK) DWELL
RUS
Gegee:
* Die verplasingsgrafiek wat eenvormige beweging toon.
* Die besonderhede van 'n nokas en 'n wigvormige volger
(mespuntvolger) op sy laagste posisie. 240° 120°
* Die vertikale senterlyn van die nokprofiel.
Spesifikasies:
* Die minimum afstand vanaf die nokprofiel na die senter
van die nokas = 26 mm.
* Nokas = Ø22 mm.
210° 150°
* Rotasie = Anti-kloksgewys.
Instruksies: 180°
* Teken, volgens skaal 1 : 1 en in die korrekte posisie, die
gegewe volger sodat dit heen en weer op die vertikale
senterlyn van die nokas sal beweeg.
* Projekteer en teken die nokprofiel vanaf die gegewe
verplasingsgrafiek.
* Toon die senterlyne en die rigting van rotasie op die 8
nokprofiel.
* Toon ALLE nodige konstruksies.
58
60°
NC
26
Ø22 SHAFT
Ø22 AS
CAMSHAFT AND FOLLOWER DETAIL NC
NOKAS- EN VOLGERBESONDERHEDE
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: LOCI - CAM / LOKUSSE - NOK
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: LOCI (CAM) 360°- 0° UNIFORM MOTION
EENVORMIGE BEWEGING
Given:
* The details of the camshaft and a wedge-ended follower
(knife-edge follower) on its lowest position. 30° 330°
* The vertical centre line of the cam profile. RISE
Specifications: STYG
* Camshaft = Ø20 mm. FALL
* The minimum distance from the cam profile to the centre of DAAL
the camshaft = 30 mm.
RISE DWELL / RUS
* Rotation = clockwise. STYG
Specifications for the movement are as follows: 60° 300°
* 0° to 90°, the follower rises 20 mm with a uniform motion.
* 90° to 150°, dwell period.
* 150° to 240°, follower rises 30 mm with a uniform motion.
0° 30° 60° 90° 120° 150° 180° 210° 240° 270° 300° 330° 360°
* 240° to 360°, the follower returns witha a uniform motion
to its original position. DISPLACEMENT GRAPH
SCALE 8 mm = 30°
55
Instruksies:
* Teken die nokas- en volgerbesonderhede. Toon die 60°
30
30° gelyk aan 8 mm en 'n vertikale skaal 1 : 1 vir die
gegewe beweging. Benoem die grafiek en sluit die skaal in. C
* Projekteer en teken die nokprofiel wat die verlangde Ø20 SHAFT
Ø20 AS
beweging sal genereer.
CAMSHAFT AND FOLLOWER DETAIL NC
* Toon ALLE nodige konstruksies. NOKAS- EN VOLGERBESONDERHEDE
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: LOCI - CAM / LOKUSSE - NOK
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: LOCI (CAM)
UNIFORM MOTION
Given: 330° EENVORMIGE BEWEGING
315°
* The details of the camshaft and a wedge-ended follower
DWELL
(knife-edge follower) on its lowest position.
0°- 360° 300° RUS
* The vertical centre line of the cam profile.
Specifications:
* Camshaft = Ø24 mm.
* The minimum distance from the cam profile to the centre of
the camshaft = 19 mm.
* Rotation = clockwise. RISE FALL
Specifications for the movement are as follows: STYG DAAL
* 0° to 150°, the follower rises 60 mm with a uniform motion. 30° 270°
* 150° to 195°, dwell period.
DWELL
* 195° to 315°, follower falls 60 mm with a uniform motion RUS
to its original height.
* 315° to 360°, dwell period with a uniform motion on the DWELL
original position. RUS
195°
315°
0° 30° 60° 90° 120° 150° 180° 210° 240° 270° 300° 330° 360°
Instructions: DISPLACEMENT GRAPH
* Draw the camshaft and follower detail. Show the arrow SCALE 8 mm = 30°
indicating the direction of rotation.
* Draw a displacement graph with a horizontal scale of 30° 60° 240° VERPLASINGSGRAFIEK
equals 8 mm and a vertical scale of 1 : 1 for the given SKAAL 8 mm = 30°
C
motion. Label the graph and includes a scale. FALL
* Project and draw the cam profile that would generate the DAAL
given motion.
* Show ALL necessary construction.
DWELL
VRAAG: LOKUSSE (NOK) RISE RUS
STYG
Instruksies:
60
* Teken die nokas- en volgerbesonderhede. Toon die
°
draairigting met behulp van 'n pyltjie. 60
* Teken die verplasingsgrafiek met 'n horisontale skaal van NC
30° gelyk aan 8 mm en 'n vertikale skaal 1 : 1 vir die
gegewe beweging. Benoem die grafiek en sluit die skaal in.
C
* Projekteer en teken die nokprofiel wat die verlangde
beweging sal genereer.
CAMSHAFT AND FOLLOWER DETAIL NC
* Toon ALLE nodige konstruksies. NOKAS- EN VOLGERBESONDERHEDE
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: LOCI - CAM / LOKUSSE - NOK
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: LOCI (CAM)
Given:
A cam profile with a wedge-ended follower (knife-ended).
UNIFORM MOTION
Specifications: 360°- 0° EENVORMIGE BEWEGING
The cam rotates with constant velocity in an anti-clockwise
DWELL
direction, imparting uniform motion to the follower. 330° 30° RUS
FALL
Instructions: DAAL
* Draw the displacement graph for the cam, using a
horizontal scale of 8 mm equals 30°. RISE
* Indicate the direction of rotation of the cam profile. STYG
300° 60° DWELL
* Label the displacement graph and indicate the scale used. RUS FALL
FALL
* Show ALL necessary construction. DAAL DAAL
105°
265°
0° 30° 60° 90° 120° 150° 180° 210° 240° 270° 300° 330° 360°
STYG
DISPLACEMENT GRAPH
Gegee: DWELL SCALE 8 mm = 30°
270° RUS 90°
* 'n Nokprofiel met 'n wigvormige volger (mespuntvolger).
VERPLASINGSGRAFIEK
SKAAL 8 mm = 30°
Spesifikasies:
* Die nok roteer teen 'n konstante snelheid in 'n anti- 265° 105°
kloksgewyse rigting en verleen eenvormige beweging aan FALL DWELL
die volger. DAAL RUS
240° 120°
Instruksies:
* Teken die verplasingsgrafiek vir die nok deur 'n horisontale
skaal van 8 mm gelyk aan 30° te gebruik.
* Toon die rigting van rotasie op die nokprofiel aan.
* Benoem die verplasingsgrafiek en toon die skaal wat
gebruik word, aan. 210° 150°
* Toon ALLE nodige konstruksies.
180°
NC
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: LOCI - CAM / LOKUSSE - NOK
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: LOCI (CAM) VRAAG: LOKUSSE (NOK)
Given: Gegee:
* The detail of the camshaft and a wedge-ended follower (knife- * Die besonderhede van 'n nokas en 'n wigvormige volger
360°
edge follower) shown at its furthest position to the left. (mespuntvolger) op sy verste posisie na links getoon.
* The vertical centre line of the camshaft as a reference on the FALL * Die vertikale senterlyn van die nokas as 'n verwysingslyn op
330°
drawing sheet. DAAL die tekenvel.
Specifications: Spesifikasies:
300°
* Camshaft = Ø22 mm. DWELL * Nokas = Ø22 mm.
* Minimum distance from the cam profile to the centre of the RUS * Minimum afstand vanaf die nokprofiel na die senter van die
camshaft = 16 mm. 270° nokas = 16 mm.
The specifications for the movement are as follows: 255° Die spesifikasies vir die beweging is soos volg:
* The cam rotates clockwise at constant velocity and imparts FALL 240° * Die nokas roteer kloksgewys teen konstante snelheid en
uniform motion to the follower. DAAL verleen eenvormige beweging aan die volger.
* Over the first 90° the follower moves 30 mm to the left (follower 210°
DISPLACEMENT GRAPH * Oor die eerste 90° beweeg die volger 30 mm na links (volgers
DWELL
rise). RUS SCALE 8 mm = 30° styg).
* There is a dwell period for the next 60°. 180° * Daar is 'n rusperiode vir die volgende 60°.
RISE VERPLASINGSGRAFIEK
* Over the next 30° the follower moves a further 10 mm to the * Oor die volgende 30° beweeg die volger 'n verdere 10 mm na
STYG
left (follower rise). 150° SKAAL 8 mm = 30° links (volgers styg).
* There is a dwell period for the next 30°. * Daar is 'n rusperiode vir die volgende 30°.
* Over the next 45° the follower moves 50% of the displacement DWELL 120° * Oor die volgende 45° beweeg die volger 50% van die
RUS
to the right (follower fall). verplasing na regs (volger daal).
* There is a dwell period for the next 45°. 90° * Daar is 'n rusperiode vir die volgende 45°.
* Over the final 60° the follower returns to its original position. * Oor die finale 60° keer die volger na sy oorspronklike posisie
60° terug.
Instructions: RISE
* Draw, to scale 1 : 1, the given views of the camshaft and the STYG Instruksies:
30°
follower using the given vertical centre line as the reference. * Teken, volgens skaal 1 : 1, die gegewe aansig van die nokas
The arrow indicating the direction of rotation must be shown. 0°
en die volger deur die vertikale senterlyn as verwysing te
* Draw the displacement graph with a rotational scale of 30° gebruik. Die pyl wat die draairigting aandui, moet getoon word.
equal to 8 mm and a displacement scale of 1:1 for the given 270° * Teken die verplasingsdiagram met 'n rotasieskaal van 30°
motion. Label the graph. 255° gelyk aan 8 mm en 'n verplasingskaal van 1 : 1 vir die gegewe
* Project and draw the cam profile that would generate the given 300° 240° beweging. Benoem die grafiek en sluit die skaal in.
motion. * Projekteer en teken die nokprofiel wat die gegewe beweging
* Show ALL necessary construction. sal genereer.
* Toon ALLE nodige konstruksies.
DWELL
RUS
360°
180°
0° C
RISE
STYG
55 16
10
30° RISE DWELL 150° C
STYG RUS Ø22 SHAFT
60° Ø22 AS NC
60°
120° CAMSHAFT AND FOLLOWER DETAIL NC
90° NOKAS- EN VOLGERBESONDERHEDE
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: LOCI - CAM / LOKUSSE - NOK
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: LOCI (CAM)
Given:
* The details of the camshaft and a wedge-ended follower
(knife-edge follower) on its starting position.
* The vertical centre line of the cam profile.
Specifications:
* Camshaft = Ø24 mm.
* The minimum distance from the cam profile to the centre of
0° - 360°
the camshaft = 22 mm.
* Rotation = clockwise. DWELL
Specifications for the movement are as follows: 30° 330° RUS
* 0° to 45°, the follower rises 24 mm with a uniform motion. RISE FALL
* 45° to 120°, dwell period. STYG DAAL
* 120° to 210°, follower falls 24 mm with a uniform motion. 45° 315°
* 210° to 255°, dwell period. 0° 360°
* 255° to 315°, follower falls 22 mm with a unifom motion. RISE
DWELL
* 315° to 360°, follower returns with a uniform motion to its RUS
60° STYG 300°
original position. FALL RISE
DAAL STYG
Instructions: RISE
STYG
* Draw the camshaft and follower detail. Show the arrow
indicating the direction of rotation.
255°
315°
45°
0° 30° 60° 90° 120° 150° 180° 210° 240° 270° 300° 330° 360°
* Draw a displacement graph with a horizontal scale of 30°
FALL DISPLACEMENT GRAPH
equals 8 mm and a vertical scale of 1 : 1 for the given SCALE 8 mm = 30°
DAAL
motion. Label the graph and includes a scale.
* Project and draw the cam profile that would generate the VERPLASINGSGRAFIEK
given motion. DWELL SKAAL 8 mm = 30°
90° RUS 270°
* Show ALL necessary construction. C
53
* 210° tot 255°, bly in rus.
* 255° tot 315°, volger daal met 22 mm met 'n eenvormige
beweging. 60°
STARTING
* 315° tot 360°, keer die volger terug met 'n eenvormige POSITION
beweging na sy oorspronklike posisie.
22
BEGIN-
Instruksies: POSISIE
* Teken die nokas- en volgerbesonderhede. Toon die
22
draairigting met behulp van 'n pyltjie.
NC
* Teken die verplasingsgrafiek met 'n horisontale skaal van
C
30° gelyk aan 8 mm en 'n vertikale skaal 1 : 1 vir die Ø24 SHAFT
gegewe beweging. Benoem die grafiek en sluit die skaal in. Ø24 AS MINIMUM
* Projekteer en teken die nokprofiel wat die verlangde DIAMETER
beweging sal genereer. CAMSHAFT AND FOLLOWER DETAIL NC
* Toon ALLE nodige konstruksies. NOKAS- EN VOLGERBESONDERHEDE
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: LOCI - CAM / LOKUSSE - NOK
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
UNIFORM MOTION 0°-360°
QUESTION: LOCI (CAM)
EENVORMIGE BEWEGING
Given:
* The displacement graph showing uniform motion. FALL 30° 330°
DAAL
* The details of the camshaft and a roller-ended follower in
its RISE
lowest position. STYG
* The vertical centre line of the cam profile.
Specifications: FALL
* The minimum distance from the cam profile to the centre of DAAL 60° 300°
the camshaft = 18 mm.
* Camshaft = Ø22 mm.
* Rotation = clockwise.
0° 30° 60° 90° 120° 150° 180° 210° 240° 270° 300° 330° 360°
Instructions:
* Draw, to scale 1 : 1 and in the correct position, the given DISPLACEMENT GRAPH
SCALE 8 mm = 30°
follower so that it will reciprocate along the vertical centre FALL
line of the camshaft. VERPLASINGSGRAFIEK DAAL
* Project and draw the cam profile from the given SKAAL 8 mm = 30°
displacement graph. 90° 270°
* Show the centre lines and the direction of rotation on the
cam profile.
* Show ALL necessary construction.
RISE FALL
STYG DAAL
VRAAG: LOKUSSE (NOK)
Gegee:
* Die verplasingsgrafiek wat eenvormige beweging toon. 120° 240°
* Die besonderhede van 'n nokas en 'n rollervormige volger
op sy laagste posisie.
* Die vertikale senterlyn van die nokprofiel.
Spesifikasies:
* Die minimum afstand vanaf die nokprofiel na die senter
van die nokas = 18 mm. 150° 210°
* Nokas = Ø22 mm.
* Rotasie = kloksgewys.
180°
Instruksies:
* Teken, volgens skaal 1 : 1 en in die korrekte posisie, die
gegewe volger sodat dit heen en weer op die vertikale 10
senterlyn van die nokas sal beweeg.
* Projekteer en teken die nokprofiel vanaf die gegewe
verplasingsgrafiek.
* Toon die senterlyne en die rigting van rotasie op die
58
nokprofiel.
* Toon ALLE nodige konstruksies. Ø16 ROLLER
NC
26
Ø22 SHAFT
Ø22 AS
CAMSHAFT AND FOLLOWER DETAIL NC
NOKAS- EN VOLGERBESONDERHEDE
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: LOCI - CAM / LOKUSSE - NOK
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: LOCI (CAM)
UNIFORM MOTION 360°- 0°
EENVORMIGE BEWEGING
Given:
* The details of the camshaft and a roller-ended follower on
DWELL
its lowest position. RUS
* The vertical centre line of the cam profile. 330° 30°
FALL
RISE
Specifications: STYG
DAAL
* Camshaft = Ø20 mm.
* The minimum distance from the cam profile to the centre of
the camshaft = 23 mm.
Specifications for the movement are as follows:
* The cam rotates anti-clockwise at constant velocity and RISE DWELL FALL 300° 60°
RUS DAAL
imparts uniform motion to the follower. STYG
* 0° to 60°, the follower rises 15 mm.
* 60° to 90°, dwell period.
165°
195°
0° 30° 60° 90° 120° 150° 180° 210° 240° 270° 300° 330° 360°
* 90° to 165°, follower rises 35 mm.
* 165° to 195°, dwell period. DISPLACEMENT GRAPH FALL
SCALE 8 mm = 30° DAAL RISE
* 195° to 330°, follower falls 35 mm. STYG
* 330° to 360°, follower returns to its original position. VERPLASINGSGRAFIEK
Instructions: SKAAL 8 mm = 30° DWELL
RUS
* Draw the camshaft and follower detail. Show the arrow
indicating the direction of rotation. 270° 90°
* Draw a displacement graph with a horizontal scale of 30°
equals 8 mm and a vertical scale of 1 : 1 for the given FALL
C
motion. Label the graph and includes a scale. DAAL
* Project and draw the cam profile that would generate the
given motion. RISE
* Show ALL necessary construction. STYG
Spesifikasies:
* Nokas = Ø20 mm.
* Minimum afstand vanaf die nokprofiel na die senter van die
nokas = 23 mm. 210° 150°
Spesifikasies vir die beweging is soos volg:
* Die nokas roteer anti-kloksgewys teen 'n konstante snelheid 195° 165°
en verleen eenvormige beweging aan die volger. 180°
10
* 0° tot 60°, volger styg 15 mm.
* 60° tot 90°, bly dit in rus.
* 90° tot 165°, volger styg met 35 mm.
* 165° tot 195°, bly in rus.
* 195° tot 330°, volger daal met 35 mm.
55
* 330° tot 360°, die volger keer terug na sy oorspronklike
posisie. Ø14
Instruksies:
* Teken die nokas- en volgerbesonderhede. Toon die
draairigting met behulp van 'n pyltjie.
30
NC
* Teken die verplasingsgrafiek met 'n horisontale skaal van
30° gelyk aan 8 mm en 'n vertikale skaal 1 : 1 vir die C
gegewe beweging. Benoem die grafiek en sluit die skaal in. Ø20 SHAFT
* Projekteer en teken die nokprofiel wat die verlangde Ø20 AS
beweging sal genereer. CAMSHAFT AND FOLLOWER DETAIL NC
* Toon ALLE nodige konstruksies. NOKAS- EN VOLGERBESONDERHEDE
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: LOCI - CAM / LOKUSSE - NOK
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: LOCI (CAM)
195°
285°
0° 30° 60° 90° 120° 150° 180° 210° 240° 270° 300° 330° 360°
* Over the final 75° the follower returns to its original position. DWELL
DISPLACEMENT GRAPH
Instructions: RUS
SCALE 8 mm = 30° RISE
* Draw the camshaft and follower detail. Show the arrow STYG
indicating the direction of rotation. VERPLASINGSGRAFIEK 240° 60°
* Draw a displacement graph with a horizontal scale of 30° SKAAL 8 mm = 30° C
equals 8 mm and a vertical scale of 1 : 1 for the given FALL DWELL
motion. Label the graph and include the scale. DAAL RUS
* Project and draw the cam profile that would generate the
given motion.
* Show ALL necessary construction.
DWELL RISE
VRAAG: LOKUSSE (NOK) RUS STYG
210° 90°
Gegee:
* Die besonderhede van 'n nokas en 'n rollervormige volger
op die laagste posisie.
* Die vertikale senterlyn van die nokprofiel.
195°
Spesifikasies:
* Nokas = Ø18 mm.
* Minimum afstand vanaf die nokprofiel na die senter van die
180° 120°
nokas = 12 mm.
Spesifikasies vir die beweging is soos volg:
* Die nokas roteer anti-kloksgewys teen 'n konstante snelheid 150°
en verleen eenvormige beweging aan die volger.
* Oor die eerste 60° styg die volger 27 mm.
* Daar is 'n rusperiode vir die volgende 60°. 8
* Oor die volgende 30° styg die volger 'n verdere 28 mm.
* Daar is 'n rusperiode vir die volgende 45°.
* Oor die volgende 45° daal die volger met 15 mm.
* Daar is 'n rusperiode vir die volgende 45°.
30°
* Oor die finale 75° keer die volger terug na sy oorspronklike
posisie.
65
Instruksies:
* Teken die nokas- en volgerbesonderhede. Toon die Ø12
draairigting met behulp van 'n pyltjie.
NC
* Teken die verplasingsgrafiek met 'n horisontale skaal van
18
C
30° gelyk aan 8 mm en 'n vertikale skaal 1 : 1 vir die Ø18 SHAFT
gegewe beweging. Benoem die grafiek en sluit die skaal in. Ø18 AS
* Projekteer en teken die nokprofiel wat die verlangde
beweging sal genereer. CAMSHAFT AND FOLLOWER DETAIL NC
* Toon ALLE nodige konstruksies. NOKAS- EN VOLGERBESONDERHEDE
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: LOCI - CAM / LOKUSSE - NOK
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
UNIFORM MOTION
QUESTION: LOCI (CAM) EENVORMIGE BEWEGING 360° - 0°
RISE
Given: STYG
A cam profile with a roller-ended follower. 30° 330°
165°
Specifications: DWELL
The cam rotates with constant velocity in a clockwise RUS
direction, imparting uniform motion to the follower. FALL
DAAL
Instructions: RISE
* Draw the displacement graph for the cam, using a STYG
horizontal scale of 6 mm equals 30°.
* Indicate the direction of rotation on the cam profile. 60° 300°
* Label the displacement graph and indicate the scale used.
* Show ALL necessary construction.
165°
0° 30° 60° 90° 120° 150° 180° 210° 240° 270° 300° 330° 360°
VRAAG: LOKUSSE (NOK) DISPLACEMENT GRAPH
SCALE 6 mm = 30°
Gegee:
* 'n Nokprofiel met 'n rollervormige volger. VERPLASINGSGRAFIEK
SKAAL 6 mm = 30° RISE
STYG
Spesifikasies:
* Die nok roteer teen 'n konstante snelheid in 'n kloksgewyse 90° 270°
rigting en verleen eenvormige beweging aan die volger. C
FALL
DAAL
Instruksies:
* Teken die verplasingsgrafiek vir die nok deur 'n horisontale
skaal van 6 mm gelyk aan 30° te gebruik.
DWELL
* Toon die rigting van rotasie op die nokprofiel aan. RUS
* Benoem die verplasingsgrafiek en toon die skaal wat RISE
gebruik word, aan. STYG
* Toon ALLE nodige konstruksies.
120° 240°
150° 210°
165°
180°
NC
NC
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: LOCI - CAM / LOKUSSE - NOK
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
UNIFORM MOTION
QUESTION: LOCI (CAM)
EENVORMIGE BEWEGING
Given: 360° - 0°
165°
100°
120°
270°
280°
290°
300°
110°
* The details of the camshaft and a roller-ended follower on (2 mm = 10°)
90°
its lowest position. DWELL
* The vertical centre line of the cam profile. RUS
330° 30°
Specifications:
* Camshaft = Ø20 mm. FALL
* The minimum distance from the cam profile to the centre of DAAL
the camshaft = 20 mm. RISE
* The maximum distance from the cam profile to the centre of STYG
the camshaft = 60 mm.
Specifications for the movement are as follows:
290°
* The cam rotates anti-clockwise at constant velocity and
DWELL 300° 60°
imparts uniform motion to the follower. FALL
RUS
* 0° to 100° the follower rises 60 mm to its maximum height. DAAL
* 100° to 150°, dwell period.
* 150° to 210°, follower falls two-third of its maximum height.
290°
* 210° to 290°, dwell period.
0° 30° 60° 90° 120° 150° 180° 210° 240° 270° 300° 330° 360°
* 290° to 360°, follower returns to its original position.
Instructions: DISPLACEMENT GRAPH
SCALE 6 mm = 30° FALL
* Draw the camshaft and follower detail. Show the arrow DAAL
indicating the direction of rotation. VERPLASINGSGRAFIEK RISE
* Draw the displacement graph with a horizontal scale of 30° SKAAL 6 mm = 30° STYG
equals 6 mm and a vertical scale of 1 : 1 for the given
motion. Label the graph and include the scale. 270° 90°
* Project and draw the cam profile that would generate the C
given motion.
DWELL
* Show ALL necessary construction. RUS
100°
VRAAG: LOKUSSE (NOK) DWELL
RUS
Gegee:
* Die besonderhede van 'n nokas en 'n rollervormige volger FALL
op die laagste posisie. DAAL
* Die vertikale senterlyn van die nokprofiel.
Spesifikasies:
* Nokas = Ø20 mm. 240° 120°
* Die minimum afstand vanaf die nokprofiel na die senter van
die nokas = 20 mm.
* Die maksimum afstand vanaf die nokprofiel na die senter van
die nokas = 60 mm.
Spesifikasies vir die beweging is soos volg:
* Die nokas roteer anti-kloksgewys teen 'n konstante snelheid
en verleen eenvormige beweging aan die volger.
* 0° tot 100° styg die volger 60 mm tot maksimum hoogte. 210° 150°
* 100° tot 150°, bly in rus.
10
* 150° tot 210°, volger daal twee-derde van sy maksimum
hoogte. 195°
180°
* 210 tot 290°, bly in rus.
* 290° tot 360°, die volger keer terug na sy oorspronklike
60
posisie.
Instruksies: Ø20
* Teken die nokas- en volgerbesonderhede. Toon die
draairigting met behulp van 'n pyltjie.
* Teken die verplasingsgrafiek met 'n horisontale skaal van NC
20
30° gelyk aan 6 mm en 'n vertikale skaal 1 : 1 vir die
gegewe beweging. Benoem die grafiek en sluit die skaal in. C
Ø20 SHAFT
* Projekteer en teken die nokprofiel wat die verlangde Ø20 AS
beweging sal genereer. CAMSHAFT AND FOLLOWER DETAIL NC
* Toon ALLE nodige konstruksies. NOKAS- EN VOLGERBESONDERHEDE
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: LOCI - CAM / LOKUSSE - NOK
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION A: LOCI (CAM) VRAAG A: LOKUS (NOK)
Motion: Beweging:
* The follower rises with simple harmonic motion for 52 mm * Die volger styg teen eenvoudige harmoniese beweging vir
over the first 180° of the rotation, to the maximum SIMPLE HARMONIC UNIFORM ACCELERATION & RETARDATION 52 mm oor die eerste 180° van die rotasie, tot by die
displacement. EENVOUDIG HARMONIESE EENVORMIGE VERSNELLING & VERTRAGING maksimum verplasing.
* The follower falls with uniform acceleration and 180° * Die volger daal teen eenvormige versnelling en vertraging
retardation to the original position over the rest of the 150° terug na die oorspronklike posisie oor die res van die rotasie.
rotation. 180°
210°
Instruksies:
Instructions: 120° * Teken, volgens 'n horisontale skaal van 12 mm = 30° en 'n
240° 210°
* Draw, to a horizontal scale of 12 mm = 30° and a verplasingskaal van 1 : 1, die volledige verplasingsdiagram
displacement scale of 1 : 1, the complete displacement 240° vir die vereiste bewegings.
graph for the required motions. RISE FALL 270° * Benoem die grafiek en dui die skaal aan.
90°
* Label the graph and indicate the scale. STYG DAAL
270°
300°
300°
60°
330° 330°
30°
0° 30° 60° 90° 120° 150° 180° 210° 240° 270° 300° 330° 360°
Motion: Beweging:
* The follower rises with uniform motion for 20 mm over * Die volger styg teen eenvormige beweging vir 20 mm oor
the first 60° of the rotation. die eerste 60° van die rotasie.
UNIFORM MOTION SIMPLE HARMONIC UNIFORM ACCELERATION & RETARDATION
* There is a dwell period for 30°. EENVORMIGE BEWEGING EENVOUDIG HARMONIESE EENVORMIGE VERSNELLING & VERTRAGING * Daar is 'n rusperiode vir 30°.
* The follower rises with a simple harmonic motion for * Die volger styg teen eenvoudige harmoniese beweging vir
180°
50 mm over the next 90° of the rotation, to the maximum 165°
50 mm oor die volgende 90° van die rotasie, tot by die
displacement of 70 mm. maksimum verplasing van 70 mm.
180°
* The follower falls with uniform acceleration and * Die volger daal teen eenvormige versnelling en
210°
retardation to the original position over the rest of the 150° vertraging terug na die oorspronklike posisie oor die res
rotation. 210° van die rotasie.
240°
Instructions: RISE Instruksies:
135°
STYG 240°
* Draw, to a horizontal scale of 130 mm = 360° and a * Teken, volgens 'n horisontale skaal van 130 mm = 360° en
displacement scale of 1 : 1, the complete displacement 270° 'n verplasingskaal van 1 : 1, die volledige verplasingsdiagram
graph for the required motions. FALL vir die vereiste bewegings.
120° DAAL 270°
* Label the graph and indicate the scale. * Benoem die grafiek en dui die skaal aan.
300°
105° 300°
90° DWELL
RUS
330° 330°
RISE
STYG
135°
105°
165°
0° 30° 60° 90° 120° 150° 180° 210° 240° 270° 300° 330° 360°/0°
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: LOCI (CAM) / LOKUSSE (NOK)
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM:
QUESTION: LOCI (CAM) UNIFORM MOTION SIMPLE HARMONIC UNIFORM ACCELERATION & RETARDATION 0°- 360°
EENVORMIGE BEWEGING EENVOUDIG HARMONIESE EENVORMIGE VERSNELLING & VERTRAGING
Given: 210°
195°
* The displacement graph showing a combination of
uniform 180°
240°
motion, simple harmonic and uniform acceleration a
RISE FALL
retardation. 165°
STYG DAAL
* The details of the camshaft and a roller-ended follower in 270°
its 150°
120°
RISE
VRAAG: LOKUSSE (NOK) STYG
Instruksies:
* Teken, volgens skaal 1 : 1 en in die korrekte posisie, die
55
gegewe volger sodat dit heen en weer op die vertikale
senterlyn van die nokas sal beweeg. Ø16
* Projekteer en teken die nokprofiel vanaf die gegewe
verplasingsgrafiek.
* Toon die senterlyne en die rigting van rotasie op die NC
22
nokprofiel.
* Toon ALLE nodige konstruksies. C
Ø30 SHAFT
Ø30 AS
CAMSHAFT AND FOLLOWER DETAIL NC
NOKAS- EN VOLGERBESONDERHEDE
10
COPYRIGHT © JP
ENGINEERING GRAPHICS & DESIGN
KOPIEREG © JP
NAME / NAAM: LOCI - CAM / LOKUSSE - NOK
GRADE / GRAAD 11: INGENIEURSGRAFIKA & ONTWERP DATE / DATUM: