2009 V Rod Muscle Owner's Manual

2009
VRod Muscle Owner's Manual
Safety First
Safe Operating Rules: VRSC Models
Motorcycles are different from other vehicles. They
operate, steer, handle and brake differently. Unskilled or
improper use could result in loss of control, death or
serious injury. (00556c)
Take a rider training course.
Read Owner's Manual before riding, adding accessories or servicing.
Wear a helmet, eye protection and protective clothing.
Never tow a trailer.
Before operating your new motorcycle it is your responsibility to read and follow the operating and
maintenance instructions in this manual, and follow these basic rules for your personal safety.
Know and respect the rules of the road (see RULES OF THE ROAD section). Carefully read
and observe the rules contained in the RIDING TIPS booklet accompanying this Owner's
Manual. Read and familiarize yourself with the contents of the MOTORCYCLE HANDBOOK
for your state.
Before starting engine, check for proper operation of brake, clutch, shifter, throttle controls,
correct fuel and oil supply.
Do not use aftermarket parts and custom made front forks
which can adversely affect performance and handling.
Removing or altering factory installed parts can adversely
affect performance and could result in death or serious
injury. (00001a)
Use only HarleyDavidson approved parts and accessories. Use of certain other
manufacturer's performance parts will void your new motorcycle warranty. See your Harley
Davidson dealer for details.
Stop the engine when refueling or servicing the fuel
system. Do not smoke or allow open flame or sparks near
gasoline. Gasoline is extremely flammable and highly
explosive, which could result in death or serious injury.
(00002a)
Do not remove radiator filler cap when engine is hot. The
cooling system is under pressure and hot coolant and
steam can escape, which could cause severe burns. Allow
engine to cool before servicing the cooling system.
(00091a)
At operating temperature, the radiator and oil cooler
contain hot fluids. Contact with the radiator or oil cooler
can result in minor or moderate burns. (00141a)
When refueling your motorcycle, the following rules should be observed.
Refuel in a well ventilated area with the engine turned off.
Remove fuel filler cap slowly.
Do not smoke or allow open flames or sparks when refueling or servicing the fuel system.
Leave air space to allow for fuel expansion.
Do not store motorcycle with gasoline in tank within the
home or garage where open flames, pilot lights, sparks or
electric motors are present. Gasoline is extremely
flammable and highly explosive, which could result in
death or serious injury. (00003a)
Engine exhaust from this product contains chemicals
known to the State of California to cause cancer, and birth
defects or other reproductive harm. (00004f)
Wheel weights on wheels without spokes contain lead and
lead compounds, chemicals known to the State of
California to cause cancer, and birth defects or other
reproductive harm. (00356d)
Do not run motorcycle in a closed garage or confined area.
Inhaling motorcycle exhaust, which contains poisonous
carbon monoxide gas, could result in death or serious
injury. (00005a)
The jiffy stand locks when placed in the full forward (down)
position with vehicle weight on it. If the jiffy stand is not in
the full forward (down) position with vehicle weight on it,
the vehicle can fall over which could result in death or
serious injury. (00006a)
Be sure jiffy stand is fully retracted before riding. If jiffy
stand is not fully retracted, it can contact the road surface
causing a loss of vehicle control, which could result in
A new motorcycle must be operated according to the special breakin procedure. See
Breakin Riding Rules: VRSC Models.
Operate motorcycle only at moderate speed and out of traffic until you have become
thoroughly familiar with its operation and handling characteristics under all conditions.
NOTE:
We recommend that you obtain information and formal training in the correct motorcycle riding
technique. In the United States, the Motorcycle Safety Foundation® offers beginning and
advanced rider safety courses. Call (949)7273227 for information.
Travel at speeds appropriate for road and conditions and
never travel faster than posted speed limit. Excessive
speed can cause loss of vehicle control, which could
result in death or serious injury. (00008a)
Do not exceed the legal speed limit or drive too fast for existing conditions. Always reduce
speed when poor driving conditions exist. High speed increases the influence of any other
condition affecting stability and increases the possibility of loss of control.
Pay strict attention to road surfaces and wind conditions. Any two wheeled vehicle may be
subject to upsetting forces such as wind blasts from passing trucks, holes in the pavement,
rough road surfaces, rider control error, etc. These forces may influence the handling
characteristics of your motorcycle. If this happens, reduce speed and guide the motorcycle
with a relaxed grip to a controlled condition. Do not brake abruptly or force the handlebar.
This may aggravate an unstable condition.
Keep cargo weight concentrated close to the motorcycle and as low as possible to minimize
the change in the motorcycle's center of gravity. Distribute weight evenly on both sides of
the vehicle and do not load bulky items too far behind the rider or add weight to the
handlebars or front forks. Do not exceed maximum specified load in each saddlebag.
NOTE:
New riders should gain experience under various conditions while driving at moderate speeds.
Operate your motorcycle defensively. Remember, a motorcycle does not afford the same
protection as an automobile in an accident. One of the most common accident situations
occurs when the driver of the other vehicle fails to see or recognize a motorcycle and turns
into the oncoming motorcyclist. Operate only with headlamp on.
Wear an approved helmet, clothing, and foot gear suited for motorcycle riding. Bright or light
colors are best for greater visibility in traffic, especially at night. Avoid loose, flowing
garments and scarves.
Avoid contact with exhaust system and wear protective
clothing that completely covers legs while riding. Exhaust
pipes and mufflers get very hot when engine is running
and remain too hot to touch, even after engine is turned
off. Failure to wear protective clothing could result in
burns or other serious injury. (00009a)
When carrying passengers, it is your responsibility to instruct them on proper riding
procedures. (See Riding Tips included in your HarleyDavidson Owner's Kit.)
Do not allow other individuals, under any circumstances, to operate your motorcycle unless
you know they are experienced, licensed riders and are thoroughly familiar with the
operation of your particular motorcycle.
Protect your motorcycle against theft. After parking your motorcycle, lock the steering head
and remove ignition key from switch. Set security alarm if present.
Safe motorcycle operation requires alert mental judgment combined with a defensive driving
attitude. Do not allow fatigue, alcohol or drugs to endanger your safety or that of others.
Vehicles equipped with a sound system should have the volume adjusted to a nondistracting
level before operating vehicle.
Maintain your motorcycle in proper operating condition in accordance with Regular Service
Intervals: 2009 VRSC Models. Particularly important to motorcycle stability is proper tire
inflation pressure, tread condition, and proper adjustment of wheel bearings and steering
head bearings.
Do not operate vehicle with forks locked. Locking the forks
restricts the vehicle's turning ability, which could result in
Perform the service and maintenance operations as
indicated in the regular service interval table. Lack of
regular maintenance at the recommended intervals can
affect the safe operation of your motorcycle, which could
Do not operate motorcycle with loose, worn or damaged
steering or suspension systems. Contact a Harley
Davidson dealer for repairs. Loose, worn or damaged
steering or suspension components can adversely affect
stability and handling, which could result in death or
Regularly inspect shock absorbers and front forks.
Replace leaking, damaged or worn parts that can
adversely affect stability and handling, which could result
in death or serious injury. (00012a)
Use HarleyDavidson replacement fasteners. Aftermarket
fasteners can adversely affect performance, which could
See a HarleyDavidson service manual for proper torque values.
Aftermarket fasteners may not have the specific property requirements to perform properly.
Be sure tires are properly inflated, balanced and have
adequate tread. Inspect your tires regularly and see a
HarleyDavidson dealer for replacements. Riding with
excessively worn, unbalanced or underinflated tires can
Replace punctured or damaged tires. In some cases, small
punctures in the tread area may be repaired from within
the demounted tire by a HarleyDavidson dealer. Speed
should NOT exceed 50 mph (80 km/h) for the first 24 hours
after repair, and the repaired tire should NEVER be used
over 80 mph (130 km/h). Failure to follow this warning
could result in death or serious injury. (00015a)
Do not exceed the motorcycle's Gross Vehicle Weight
Rating (GVWR) or Gross Axle Weight Rating (GAWR).
Exceeding these weight ratings can affect stability and
handling, which could result in death or serious injury.
(00016e)
GVWR is the sum of the weight of the motorcycle, accessories, and the maximum weight of
the rider, passenger and cargo that can be safely carried.
GAWR is the maximum amount of weight that can be safely carried on each axle.
The GVWR and GAWR are shown on the information plate, located on the frame down
tube.
Do not tow a disabled motorcycle. Towing can adversely
affect stability and handling, which could result in death or
Do not pull a trailer with a motorcycle. Pulling a trailer can
cause tire overload, reduced braking efficiency and
in death or serious injury. (00018b)
Direct contact of D.O.T. 4 brake fluid with eyes can cause
irritation. Avoid eye contact. In case of eye contact flush
with large amounts of water and get medical attention.
Swallowing large amounts of D.O.T. 4 brake fluid can
cause digestive discomfort. If swallowed, obtain medical
attention. Use in well ventilated area. KEEP OUT OF
REACH OF CHILDREN. (00240a)
Batteries, battery posts, terminals and related accessories
contain lead and lead compounds, and other chemicals
defects or other reproductive harm. Wash hands after
handling. (00019e)
Consult a HarleyDavidson dealer regarding any questions
or problems that occur in the operation of your
motorcycle. Failure to do so can aggravate an initial
problem, cause costly repairs, cause an accident and
Be sure all equipment required by federal, state and local law is installed and in good
operating condition.
If ABS lamp remains on continuously, the ABS is not
operating. The standard brake system is operational, but
wheel lock up can occur. Contact a HarleyDavidson
Dealer to have ABS repaired. A locked wheel will skid and
can cause loss of vehicle control, which could result in
ABS cannot prevent lockup of rear wheel due to engine
braking. ABS will not aid in cornering or on loose/uneven
surfaces. A locked wheel will skid and can cause loss of
vehicle control, which could result in death or serious
injury. (00362a)
Rules of the Road
Always sound your horn, actuate your turn signals, and exercise caution when passing other
vehicles going in the same direction. Never try to pass another vehicle going in the same
direction at street intersections, on curves, or when going up or down a hill.
At street intersections give the rightofway. Do not presume you have the rightofway, as
the other driver may not know it is your turn.
Always signal when preparing to stop, turn or pass.
All traffic signs, including those used for the control of traffic at intersections, should be
obeyed promptly. SLOW DOWN signs near schools and CAUTION signs at railroad
crossings should always be observed and your actions governed accordingly.
When intending to turn, signal at least 100 feet 30.5 meters before reaching the turning
point. If turning across an intersection, move over to the centerline of the street (unless local
rules require otherwise). Slow down when entering the intersection and turn carefully.
Never anticipate a traffic light. When a change is indicated from GO to STOP (or vice versa)
in the traffic control systems at intersections, slow down and wait for the light to change.
Never run through a yellow or red traffic light.
While turning either right or left, watch for pedestrians, animals, as well as vehicles.
Do not leave the curb or parking area without signaling. Be sure your way is clear to enter
moving traffic. A moving line of traffic always has the rightofway.
Be sure your license plate is installed in the position specified by law and is clearly visible at
all times. Keep the plate clean.
Ride at a safe speed that is consistent with the type of highway you are on. Pay strict
attention to whether the road is dry, oily, icy or wet.
Watch for debris such as leaves or loose gravel.
Weather and traffic conditions on the highway dictate adjusting your speed and driving
habits accordingly.
Accessories and Cargo
HarleyDavidson Motor Company cannot test and make specific recommendations concerning
every accessory or combination of accessories sold. Therefore, the rider must be responsible for
safe operation of the motorcycle when installing accessories or carrying additional weight.
See the Accessory and Cargo section in your Owner's
Manual. Improper loading of cargo or installation of
accessories can affect motorcycle stability and handling,
which could result in death or serious injury. (00021a)
Rating (GVWR) or Gross Axle Weight Rating (GAWR).
Exceeding these weight ratings can affect stability and
handling, which could result in death or serious injury.
(00016e)
GVWR is the sum of the weight of the motorcycle, accessories, and the maximum weight of
the rider, passenger and cargo that can be safely carried.
GAWR is the maximum amount of weight that can be safely carried on each axle.
The GVWR and GAWR are shown on the information plate which is located on the frame
down tube.
Do not pull a trailer with a motorcycle. Pulling a trailer can
cause tire overload, reduced braking efficiency and
in death or serious injury. (00018b)
Accessory and Cargo Guidelines
The following guidelines should be used when equipping a motorcycle, carrying passengers
and/or cargo.
Do not exceed the legal speed limit or drive too fast for existing conditions. Always reduce
speed when poor driving conditions exist. High speed increases the influence of any other
condition affecting stability and increases the possibility of loss of control.
Pay strict attention to road surfaces and wind conditions. Any two wheeled vehicle may be
subject to upsetting forces such as wind blasts from passing trucks, holes in the pavement,
rough road surfaces, rider control error, etc. These forces may influence the handling
characteristics of your motorcycle. If this happens, reduce speed and guide the motorcycle
with a relaxed grip to a controlled condition. Do not brake abruptly or force the handlebar.
This may aggravate an unstable condition.
Keep cargo weight concentrated close to the motorcycle and as low as possible. This
minimizes the change in the motorcycle's center of gravity.
Distribute weight evenly on both sides of the vehicle.
Do not load bulky items too far behind the rider or add weight to the handlebars or front
forks.
Do not exceed maximum specified load in each saddlebag.
Luggage racks are designed for lightweight items. Do not overload racks.
Be sure cargo is secure and will not shift while riding and recheck the cargo periodically.
Accessories that change the operator's riding position may increase reaction time and affect
handling of the motorcycle.
Additional electrical equipment may overload the motorcycle's electrical system possibly
resulting in electrical system and/or component failure.
The front and/or rear guard(s) can provide limited leg and
cosmetic vehicle protection under unique circumstances.
(Fall over while stopped, very slow speed slide.) It is not
made or intended to provide protection from bodily injury
in a collision with another vehicle or any other object.
(00022a)
Large surfaces such as fairings, windshields, back rests, and luggage racks can adversely affect
handling. Only genuine HarleyDavidson items designed specifically for the motorcycle model
should be used with proper installation.
injury. (00001a)
Only Touring HarleyDavidson Motorcycles are suitable for
sidecar use. Consult a HarleyDavidson dealer. Use of
motorcycles other than Touring models with sidecars
Noise Control System
Tampering
Owners are warned that removal or replacement of any noise control system component may be
prohibited by law. This prohibition applies prior to vehicle sale or delivery to the ultimate
purchaser. Use of a vehicle on which noise control system components have been removed or
rendered inoperative may also be prohibited by law.
Identification
Vehicle Identification Number: VRSC Models
See V.I.N. Stamping Location: VRSC Models. The full 17digit serial or Vehicle Identification
Number (V.I.N.) is stamped on the steering head and on a label located on the left frame tube
above the front engine cylinder.
An abbreviated V.I.N. is stamped on the left side crankcase above the sump.
NOTE:
Always give the full 17digit Vehicle Identification Number when ordering parts or making any
inquiry about your motorcycle.
V.I.N. Stamping Location: VRSC Models
Typical HarleyDavidson V.I.N.: 2009 VRSC Models
HarleyDavidson V.I.N. Breakdown: 2009 VRSC Models
POSITION DESCRIPTION POSSIBLE VALUES

1 Market 1=Originally manufactured for sale within the United States
designation
5=Originally manufactured for sale outside of the United States
2 Manufacturer HD=HarleyDavidson
3 Motorcycle type 1=Heavyweight motorcycle (901 cc and larger)
4 Model See V.I.N. model table
5 Engine type H=Revolution®, 1250 cc liquidcooled, fuel injected
J=Revolution®, 1250 cc liquidcooled, fuel injected 105 HP HDI
only
6 Introduction date 1=Regular
2=Midyear
3=California/regular
4=Cosmetic changes and/or special introductory date
5=California/cosmetic changes and/or special introductory date
6=California/midyear
7 V.I.N. check digit Can be 09 or X
8 Model year 9=2009
9 Assembly plant K=Kansas City, MO USA
10 Sequential Varies
number
V.I.N. Model Codes: 2009 VRSC Models
CODE MODEL CODE MODEL

HF VRSCAW VRod™ HH VRSCDX Night Rod Special®
HP VRSCF VRod Muscle®
Labels
See Labels: VRSC Models for safety and maintenance labels which were on the vehicle when
new. If removed, replacement labels may be purchased for your motorcycle. Refer to Labels:
VRSC Models for label descriptions.
NOTE:
Some labels may be available in different languages for destinations outside the U.S. See a
HarleyDavidson dealer for all labels available for purchase.
Labels: VRSC Models
LABEL PART NO. DESCRIPTION LOCATION

1 1534801A General Rear of airbox cover.
warnings
2 1536801A Battery Under seat, rear of fuel tank.
warning
3 1536901 Check oil level Under seat, rear of fuel tank.
4 1536709 Antitampering Under seat on right frame tube.
label
(VRSCAW)
1539609
(VRSCDX)
1539809
(VRSCF)
5 1372508 Fuse block Label with START RELAY and FAN RELAY is located
labels behind front right side cover. Other half of label is on fuse
(ABS block under passenger seat, behind fuel filler.
models)
1369407
(NonABS)
Labels: VRSC Models
Specifications
Specifications: 2009 VRSC Models
Engine: 2009 VRSC Models
ITEM SPECIFICATION
Number of 2
cylinders
Type 4cycle, DOHC, 60 degree VType,
water cooled
Compression 11.51
ratio
Bore 4.134 in. 105.00 mm
Stroke 2.835 in. 72.00 mm
Displacement 76.28 cu. in. 1250.00 cu. cm
NOTE:
Specifications in this publication may not match those of official certification in some markets due
to timing of publication printing, variance in testing methods, and/or vehicle differences.
Customers seeking officially recognized regulatory specifications for their vehicle should refer to
certification documents and/or contact their respective dealer or distributor.
Ignition System: 2009 VRSC Models
ITEM SPECIFICATION
Timing setting Not adjustable
Battery 12 volt, 19 amp/hr, 270 CCA
Spark plug type 10R12A
Spark plug gap 0.035 in. 0.89 mm
Spark plug gap 0.035 in. 0.89 mm
Spark plug torque 17 ftlbs 23 Nm
Engine Torque: 2009 VRSC Models
MODEL TORQUE
VRSCAW (DOM/HDI) 84.00 ftlbs 113.90 Nm
@7000 RPM @7000 RPM
VRSCAW (France 80.00 ftlbs 108.48 Nm
opt. Germany) @6500 RPM @6500 RPM
VRSCAW (Japan) 77.00 ftlbs 104.41 Nm
@7000 RPM @7000 RPM
VRSCDX (DOM) 85.00 ftlbs 115.26 Nm
@7000 RPM @7000 RPM
VRSCDX (HDI) 83.00 ftlbs 112.55 Nm
@7500 RPM @7500 RPM
VRSCDX (France opt. 78.00 ftlbs 105.77 Nm
Germany) @7000 RPM @7000 RPM
VRSCDX (Japan) 79.00 ftlbs 107.12 Nm
@7000 RPM @7000 RPM
VRSCF (DOM) 86.00 ftlbs 116.62 Nm
@6500 RPM @6500 RPM
VRSCF (HDI) 85.00 ftlbs 115.26 Nm
@6500 RPM @6500 RPM
VRSCF (France opt. 84.00 ftlbs 113.90 Nm
Germany) @6250 RPM @6250 RPM
VRSCF (Japan) 81.00 ftlbs 109.84 Nm
@6500 RPM @6500 RPM
Capacities: 2009 VRSC Models
ITEM U.S. LITERS

Fuel tank 5.00 gal 18.93
Low fuel warning lamp on 0.50 gal 1.89
Oil capacity with filter 4.50 qt. 4.26
Coolant capacity 2.50 qt. 2.37
Transmission: 2009 VRSC Models
ITEM SPECIFICATION
Type foot shift
Speeds 5 forward
Gears 1st, 5th spur gears
2nd, 3rd, 4th helical gears
Drivetrain: 2009 VRSC Models
COMPONENT TYPE
Primary drive gear
Final drive belt
Rear sprocket compensated
Clutch hydraulic, slip and assist
Sprocket Teeth: 2009 VRSC Models
ITEM DOMESTIC INTERNATIONAL

Transmission 28 30
Rear wheel 72 72
Ratio 0.42 0.39
Gear Ratios: 2009 VRSC Models
GEAR DOMESTIC INTERNATIONAL

1st gear 11.752 10.969
2nd gear 7.898 7.371
3rd gear 6.322 5.900
4th gear 5.459 5.095
5th gear 4.889 4.563
Dimensions: 2009 VRSC Models
ITEM VRSCAW VRSCDX VRSCF

IN. MM IN. MM IN. MM
Wheelbase 67.20 1706.88 67.20 1706.88 67.00 1701.80
Overall length 94.40 2397.76 94.40 2397.76 92.80 2357.12
Overall width 34.50 876.30 34.60 878.84 40.20 1021.08
Overall height 47.70 1211.58 45.50 1155.70 45.70 1160.78
Road clearance 5.00 127.00 4.20 106.68 4.80 121.92
Seat height* 26.00 660.40 25.20 640.08 25.60 650.24
*With 180 lb. (82 kg) rider on seat.
Weights: 2009 VRSC Models

LB. KG LB. KG LB. KG
Weight (as shipped from factory) 637.00 288.94 643.00 291.66 640.00 290.30
GVWR 1075.00 487.61 1075.00 487.61 1075.00 487.61
GAWR Front 377.00 171.00 377.00 171.00 377.00 171.00
GAWR Rear 698.00 316.61 698.00 317.61 698.00 317.61
NOTE:
Gross Vehicle Weight Rating GVWR (maximum allowable loaded vehicle weight) and
corresponding Gross Axle Weight Ratings (GAWR) are given on a label located on the left frame
tube above the front engine cylinder.
Tire Sizes: 2009 VRSC Models
MOUNT SIZE NUMBER

Front 19 in. D208F 120/70ZR19 60W
Rear 18 in. D419 240/40R18 79V
All 2009 models use Dunlop radial tires only.
Tire Pressures: 2009 VRSC Models
LOAD TIRE PRESSURE (COLD)
FRONT REAR
PSI kPa PSI kPa
solo rider 36 248 38 262
rider and passenger 36 248 42 290
Bulb Chart: 2009 VRSC Models
LAMP DESCRIPTION BULBS CURRENT DRAW HD PART
(ALL LAMPS 12 VOLT) REQUIRED (AMPERAGE) NUMBER

Headlamp low beam 1 4.30 6888101
VRSCAW, VRSCF high beam 1 5.10 6771701

Headlamp low beam/high beam 1 4.58/5.00 6832903
VRSCDX
Position lamp position lamp 1 0.36 5343697
international
Tail and stop lamp tail/stop lamp 1 0.59/2.25 6816889A
license plate illumination 2 0.33 6819395
VRSCAW,
VRSCDX tail/stop lamp international 1 0.42/1.75 6816990A
international
Tail and stop lamp Illuminated with LEDs. Replace entire assembly upon failure.
VRSCF
License plate Illuminated with LEDs. Replace entire assembly upon failure.
illumination
VRSCF
Turn signal lamp front/running 2 2.25/0.59 6816889
rear 2 2.25 6857264B
VRSCAW,
VRSCDX front/running international 2 1.75 6816384
rear international 2 1.75 6816384
Turn signal lamp front/running Illuminated with LEDs. Replace entire
assembly upon failure.
VRSCF
rear Illuminated with LEDs. Replace entire
assembly upon failure.
Instrument cluster Illuminated with LEDs. Replace entire assembly upon failure.
Tire Data: VRSC Models
Match tires, tubes, air valves and caps to the correct wheel
rim. Contact a HarleyDavidson dealer. Mismatching can
result in damage to the tire bead, allow tire slippage on the
rim or cause tire failure, which could result in death or
Use only HarleyDavidson approved tires. See a Harley
Davidson dealer. Using nonapproved tires can adversely
affect stability, which could result in death or serious
injury. (00024a)
Tubeless tires are used on all HarleyDavidson cast and disc wheels.
Tire sizes are molded on the tire sidewall. Inner tube sizes are printed on the tube.
HarleyDavidson front and rear tires are not the same.
Interchanging front and rear tires can cause tire failure,
Do not inflate tire beyond maximum pressure as specified
on sidewall. Over inflated tires can blow out, which could
HarleyDavidson tires are equipped with wear bars that run
horizontally across the tread. When wear bars become
visible and only 1/32 in. (0.8 mm) tread depth remains,
replace tire immediately. Using a worn tire can adversely
serious injury. Use only HarleyDavidson approved
replacement tires. (00090b)
See Specifications: 2009 VRSC Models for tire pressures and sizes.
Catalytic Converters: VRSC Models
All international (HDI) motorcycles are equipped with catalytic converters. Domestic and
destination Japan motorcycles are not equipped with catalytic converters.
Do not operate catalytic converterequipped vehicle with
engine misfire or a nonfiring cylinder. If you operate the
vehicle under these conditions, the exhaust will become
abnormally hot, which can cause vehicle damage,
including emission control loss. (00149a)
Gasoline Blends
Your motorcycle was designed to get the best performance and efficiency using unleaded
gasoline. Most gasoline is blended with alcohol and/or ether to create oxygenated blends. The
type and amount of alcohol or ether added to the fuel is important.
Do not use gasoline that contains methanol. Doing so can
result in fuel system component failure, engine damage
and/or equipment malfunction. (00148a)
Gasoline containing METHYL TERTIARY BUTYL ETHER (MTBE): Gasoline/MTBE blends
are a mixture of gasoline and as much as 15% MTBE. Gasoline/MTBE blends can be used
in your motorcycle.
ETHANOL is a mixture of 10% ethanol (Grain alcohol) and 90% unleaded gasoline.
Gasoline/ethanol blends can be used in your motorcycle if the ethanol content does not
exceed 10%.
REFORMULATED OR OXYGENATED GASOLINES (RFG): Reformulated gasoline is a
term used to describe gasoline blends that are specifically designed to burn cleaner than
other types of gasoline, leaving fewer tailpipe emissions. They are also formulated to
evaporate less when you are filling your tank. Reformulated gasolines use additives to
oxygenate the gas. Your motorcycle will run normally using this type of gas and Harley
Davidson recommends you use it when possible, as an aid to cleaner air in our
environment.
Do not use race gas or octane boosters. Use of these fuels will damage the fuel system.
Some gasoline blends might adversely affect the starting, driveability or fuel efficiency of the
motorcycle. If any of these problems are experienced, try a different brand of gasoline or gasoline
with a higher octane blend.
Fuel
Refer to Octane Ratings. Always use a good quality unleaded gasoline. Octane ratings are
usually found on the pump.
Avoid spills. Slowly remove filler cap. Do not fill above
bottom of filler neck insert, leaving air space for fuel
expansion. Secure filler cap after refueling. Gasoline is
extremely flammable and highly explosive, which could
Use care when refueling. Pressurized air in fuel tank can
force gasoline to escape through filler tube. Gasoline is
Modern service station pumps dispense a high flow of gasoline into a motorcycle fuel tank making
air entrapment and pressurization a possibility.
Octane Ratings
SPECIFICATION RATING
Pump Octane (R+M)/2 91 (95 RON)
Controls and Indicators
General: Controls and Indicators
Read the CONTROLS AND INDICATORS section before
riding your motorcycle. Failure to understand the
operation of the motorcycle could result in death or
Some features explained are unique to certain models. These features may be available as
accessories for your HarleyDavidson motorcycle. See a HarleyDavidson dealer for a complete
list of accessories that will fit your specific motorcycle.
Ignition Switch: VRSC Models
The automaticon headlamp feature provides increased
visibility of the rider to other motorists. Be sure headlamp
is on at all times. Poor visibility of rider to other motorists
can result in death or serious injury. (00030b)
See the YOUR OWNER'S MANUAL section at the beginning of this manual. Be sure to record all
your key numbers in the space provided at the front of this book.
The ignition switch controls electrical functions of the motorcycle.
Protect your vehicle against theft. After parking your
motorcycle, lock the steering head and ignition switch.
Failure to lock your motorcycle can result in theft and/or
equipment damage. (00491c)
Do not lubricate barrel locks with petroleum based
lubricants or graphite. Inoperative locks may result.
(00152a)
Turn the ignition switch to the OFF position before locking
the motorcycle. Leaving the switch in the ACC position will
keep the instrument lights on and result in a discharged
battery. (00492b)
To review the functions of each switch position, refer to Ignition Switch: VRSC Models.
1. See Ignition Switch: VRSC Models. To remove the key from the ignition, turn it to the
OFF position.
2. To remove the key from ignition, pull the key outward.
3. Always turn switch to LOCK position and remove key after operation and when leaving bike
parked.
NOTES:
ACCAccessories and hazard warning flasher can be turned on. Instrument lamps are on.
Brake lamp and horn can be activated. Key may be removed.
The lamps operate when the switch is in the IGN position, as required by law in some
localities.
HarleyDavidson recommends removing key from ignition/fork lock before operating
motorcycle. If you do not remove key, it can fall out during operation.
The ignition key also fits the front fork lock.
SWITCH REMOVE FUNCTIONS

POSITION KEY
OFF Yes Turns off ignition, lamps and accessories (disconnects battery voltage
from IGN and ACC terminals).
ACC Yes Turns on accessories. Hazard warning flashers can be operated.
Instrument lamps are on. Brake lamp and horn can be activated (connects
battery voltage to ACC terminal).
NOTE: When switching to the ACC position, a startup diagnostic performs
a systems check. The instrument background lighting illuminates, gauge
needles sweep their full range of motion and the battery, security, coolant
temperature and check engine indicator lamps illuminate.
IGN Yes Turns on ignition, lamps and accessories.
1. Accessory position
2. OFF position
3. Ignition position
Hand Controls: Basic Operation
Electric Starter Switch
NOTE:
Off/Run switch MUST be in RUN position to operate engine.
See Handlebar Controls: VRSC Models. The electric starter switch is located on the right
handlebar control group. See Starting the Engine: VRSC Models for detailed operation
procedures.
1. Put the engine off/run switch in the RUN position and the transmission in neutral. Neutral
(green) indicator lamp should be illuminated.
2. See Ignition Switch: VRSC Models. Turn ignition/headlamp key switch to IGNITION and
push the START switch to operate starter motor.
Engine OFF/RUN Switch
See Handlebar Controls: VRSC Models. The engine off/run switch (7) turns the ignition power
ON or OFF. The engine off/run switch is located on the right handlebar control. Push the top
portion of the engine off/run switch to turn off ignition power and shut the engine off. Push the
bottom portion of the engine off/run switch to turn on ignition power.
NOTES:
The engine off/run switch must be in the RUN position to start or operate the engine.
The engine off/run switch should be used to shut the engine off.
1. To shut the engine off, push the top of the off/run switch to the ignition OFF position.
2. See Ignition Switch: VRSC Models. Turn the ignition key to the OFF position to turn the
ignition power completely OFF.
Throttle Control Grip
See Handlebar Controls: VRSC Models. The throttle control grip (9) is located on the right
handlebar control and is operated with the right hand.
To reduce rider fatigue on long trips, a spring loaded throttle friction adjustment screw (10) is
located at the bottom of the throttle grip clamp on noncruise equipped models.
1. Slowly turn throttle control grip clockwise (toward the front of the bike) to close the throttle
(decelerate).
2. Slowly turn throttle control grip counterclockwise (toward rear of bike) to open the throttle
(accelerate).
Do not tighten throttle friction adjustment screw to the
point where the engine will not return to idle automatically.
Overtightening can lead to loss of vehicle control, which
could result in death or serious injury. (00031b)
3. Unscrew the throttle friction adjustment screw so the throttle returns to the idle position
when the hand is removed from the grip.
4. Screw the throttle adjustment screw in to increase friction on grip. This provides a damping
effect on throttle motion.
NOTE:
The throttle friction adjustment screw should not be used under normal stop and go operating
conditions.
Clutch Hand Lever
Do not position fingers between hand control lever and
handlebar grip. Improper hand positioning can impair
control lever operation and cause loss of vehicle control,
See Handlebar Controls: VRSC Models. The clutch hand lever (1) is located on the left
handlebar and is operated with the fingers of the left hand.
1. Slowly pull clutch hand lever in against handlebar grip to fully disengage clutch.
2. Shift to first gear using the gear shifter lever. See Shifting Gears.
3. Slowly release the clutch hand lever to engage clutch.
A clutch switch is incorporated into the left handlebar switch assembly. It enables the rider to start
the vehicle in any gear (or in neutral) as long as the clutch lever is pulled in. If the clutch is not
disengaged, the vehicle will not start.
Horn Switch
See Handlebar Controls: VRSC Models. The horn is operated by pushing on the horn switch
(2) located on the left handlebar control group.
Headlamp Dimmer Switch
See Handlebar Controls: VRSC Models. The headlamp dimmer switch (3) is located on the left
handlebar. The switch has two positions to activate the headlamps high or low beams.
Press the top of the headlamp dimmer beam switch to activate the high beam.
Press the bottom of the headlamp dimmer switch to return to the low beam.
See Indicator Lamps: VRSC Models. The (blue) high beam indicator lamp will illuminate when
the high beam is on.
Turn Signal Switches
See Handlebar Controls: VRSC Models. Each handlebar control group contains a turn signal
switch.
The right turn signal switch (11) operates the right front and right rear flashing lamps.
The left turn signal switch (4) operates the left front and left rear flashing lamps.
NOTE:
Front turn signal lamps also function as running lamps (except International models).
1. Clutch hand lever
2. Horn switch
3. Headlamp dimmer switch
4. Left turn signal switch
5. Front brake master cylinder reservoir
6. Electric starter switch
7. Engine off/run switch
8. Brake hand lever
9. Throttle control grip
10. Throttle friction adjusting screw
11. Right turn signal switch
12. Clutch master cylinder reservoir
Handlebar Controls: VRSC Models
Turn Signal Switch Operation
The turn signal switches are used by the turn signal module to control turn signal operation based
on vehicle speed, vehicle acceleration and turn completion.
Momentarily depress the desired turn signal switch. The turn signal lamps will begin and continue
flashing until they are manually or automatically cancelled. As long as the motorcycle is
stationary, the signals will flash.
NOTES:
If you are signaling to turn in one direction and you depress the switch for the opposite turn
signal, the first signal is cancelled and the opposite side begins flashing.
If you want to stop the lamps from flashing, briefly depress the turn signal switch a second
time. The turn signal lamps will stop flashing.
Hazard Warning 4Way Flasher
Use the following method to activate the fourway flashers.
1. With the ignition key ON and security system disarmed (if equipped), press the left and right
turn signal switches at the same time.
2. Turn the ignition key OFF and arm the security system if present and desired. The fourway
flashers will continue for two hours.
3. To cancel fourway flashing, disarm the security system if necessary, turn the ignition key
ON and press the left and right turn signal switches at the same time.
This system allows a stranded vehicle to be left in the fourway flashing mode and secured until
help is found.
Indicator Lamps: VRSC Models
See Indicator Lamps: VRSC Models. Eleven indicator lamps are provided in the instrument
cluster.
The two green TURN indicator lamps flash when turn signals are activated; therefore,
flashing indicates the chosen turn direction. When the 4way hazard flashers are operating,
both turn indicators flash simultaneously.
The blue HIGH BEAM indicator lamp, when lit, signals high beam headlamp operation.
The green NEUTRAL lamp, when lit, signals the transmission is in neutral gear.
The red OIL PRESSURE indicator lamp, when lit, signals that oil is not circulating through
the engine.
The red ENGINE COOLANT TEMPERATURE indicator lamp, when lit, signals the coolant
temperature has exceeded 243° F (117° C).
The red ENGINE DIAGNOSTIC indicator lamp, when lit, signals that the vehicle's computer
has detected an engine malfunction.
The red ALTERNATOR indicator lamp, when lit, signals there is a malfunction in the
charging circuit and the battery is not being properly charged.
The red SECURITY STATUS indicator lamp indicates the status of the vehicle's security
system. It is normal for this to light with or without a security system.
The yellow LOW FUEL indicator lamp, when lit, signals the fuel tank is almost empty.
On ABS equipped models, the amber ABS indicator lamp begins to flash at key ON to
indicate that the system is operational. It continues to flash until motorcycle speed exceeds
3 mph 5 km/h . Continuous illumination of the lamp will only occur when ABS detects that
the system is malfunctioning. In the diagnostic mode, the lamp will also illuminate to indicate
the presence of diagnostic trouble codes (DTCs). See a HarleyDavidson dealer for service.
If ABS lamp remains on continuously, the ABS is not
operating. The standard brake system is operational, but
wheel lock up can occur. Contact a HarleyDavidson
Dealer to have ABS repaired. A locked wheel will skid and
can cause loss of vehicle control, which could result in
NOTES:
The OIL PRESSURE indicator lamp will glow when the ignition is turned on prior to starting
the engine. With the engine running, the lamp should be off when engine speed is above
idle.
To learn more about the SECURITY STATUS indicator lamp, see the HD Factory Security
Section later in this manual.
Several other circumstances that could cause the red oil pressure indicator lamp to illuminate
include:
An insufficient or diluted oil supply causing the oil pressure indicator lamp to remain lit at
speeds above idling.
An oil feed clogged with ice and sludge in freezing weather, preventing oil circulation.
A grounded oil signal switch wire.
A faulty oil signal switch.
A damaged or improperly installed check valve.
Trouble with the oil pump.
If the oil pressure indicator lamp remains lit, always check
the oil supply first. If the oil supply is normal and the lamp
is still lit, stop the engine at once and do not ride further
until the trouble is located and the necessary repairs are
made. Failure to do so may result in engine damage.
(00157a)
Several other circumstances that could cause the red engine coolant temperature indicator lamp
to illuminate include:
Cooling fan malfunction.
Low coolant level.
Thermostat malfunction.
Temperature gauge malfunction.
Blocked coolant passages.
Radiator cap malfunction.
Coolant malfunction.
If the engine coolant temperature indicator lamp remains
lit, always check the coolant level. If the coolant level is
normal and the lamp is still lit, stop the engine at once and
do not ride further until the trouble is located and the
necessary repairs are made. Failure to do so may result in
engine damage. (00158a)
(00091a)
1. Left turn
2. High beam
3. Neutral
4. Oil
5. Engine coolant
6. Right turn
7. Low fuel
8. Security system
9. ABS
10. Alternator
11. Engine diagnostic
Indicator Lamps: VRSC Models
Instruments: VRSC Models
Speedometer
See Instrument Cluster: VRSC Models. The speedometer registers miles per hour (U.S.
models) or kilometers per hour (international models) of forward speed. The speedometer also
provides the following selectable functions:
Odometer
Trip odometers A and B
12 or 24 hour clock
Fuel range
Never attempt to tamper with or alter the vehicle odometer.
This is illegal. Tampering with or altering a vehicle
odometer may cause equipment damage. (00160a)
The speedometer has a single display window for the above functions.
1. See Instrument Cluster: VRSC Models. Pressing the function switch with the ignition
switch in any position will activate the odometer reading and time. Time and mileage or
kilometers may be checked without unlocking ignition switch. Press and release function
switch once to view odometer. Press and release switch again to display time.
2. To check mileage on trip odometers, the ignition switch must be in the ACC or IGNITION
position. Press and release the function switch until the desired trip odometer reading is
displayed. An 'A' or 'B' in the upper left of the display window identifies trip odometers.
3. To reset or zero trip odometers, have desired odometer (A or B) in display window. Press
function switch and hold switch for 23 seconds. The trip odometer will be reset to zero.
4. Repeat the previous step if you wish to zero both trip odometers.
Setting Clock
1. Turn the ignition switch to ACC or IGNITION.
2. See Instrument Cluster: VRSC Models. Press function switch until time (hour and
minutes) is displayed. Press and hold the function switch for five seconds or until 12HR
begins to blink in the speedometer display window. Release the button.
3. Press and release the function switch once to advance to a blinking 24HR military style time
display. Each time you press and release the button, the display will switch between 12HR
and 24HR.
4. When the desired time style is displayed, press and hold the function switch for five
seconds. The display will switch to the time display with the hours blinking.
5. Press and release the function switch repeatedly to advance the hours. Each time you press
and release the switch, the display will advance one hour.
NOTE:
No AM or PM time setting is required. When correct hour is reached, press and hold
function switch to advance to minute setting.
6. When the correct hour is displayed, press and hold the function switch for five seconds. The
minutes display will start blinking.
7. Press and release the function switch repeatedly to advance the minutes display. Each time
you press and release the button, the display will advance one minute.
8. When the correct minutes are displayed, press and hold the function switch for five seconds.
The minutes display will stop blinking, indicating that the clock has been set.
9. Turn the ignition switch OFF.
Fuel Range Function
The fuel range function shows the approximate mileage available with the amount of fuel left in
the fuel tank.
1. With the ignition switch in the ACC or IGNITION position, press function switch until fuel
range function is displayed, as indicated by the letter 'r' in the left side of the odometer
display. The calculated remaining distance (miles or kilometers) to empty is displayed,
based on the amount of fuel in tank. Range can be accessed at any time using the function
switch.
2. When the low fuel warning lamp illuminates, the range feature will automatically be
displayed in the odometer unless this automatic popup feature is disabled by a press and
hold of the function switch while in range display mode. Automatic range popup feature will
show that it is disabled by blinking twice. Likewise, automatic range popup can be
reactivated by a press and hold of the function switch. Range will blink once when the
automatic popup feature is reenabled.
NOTE:
When the low fuel warning lamp turns on, there is approximately 0.50 gallon 1.89 liters
of fuel remaining in the tank. Refuel as soon as possible.
The range display is only updated when the vehicle is moving.
3. After the range calculation reaches 10 miles 16 kilometers remaining, the range display will
display "r Lo" to indicate that the vehicle will shortly run out of fuel.
4. Resetting the low fuel warning lamp and range requires an ignition cycle change.
Tachometer
See Instrument Cluster: VRSC Models. The tachometer registers the engine speed in
revolutions per minute (RPM).
See OPERATING RECOMMENDATIONS section. Do not
operate the engine above maximum safe RPM as shown
under OPERATION (red zone on tachometer). Lower the
RPM by upshifting to a higher gear or reducing the amount
of throttle. Failure to lower RPM may cause equipment
damage. (00159a)
Tip Indicator Lamp
If tip occurs, check all controls for proper operation.
Restricted control movement can adversely affect the
performance of the brakes, clutch or ability to shift, which
could result in loss of vehicle control and death or serious
injury. (00350a)
Should motorcycle be tipped over, the word "tip" will appear in the odometer window. Engine will
not start until reset. To reset, cycle ignition/headlamp key switch ONOFFON.
1. Tachometer
2. Speedometer
3. Fuel gauge
4. Odometer/tripodometer/clock/fuel range display
5. Function switch
Instrument Cluster: VRSC Models
Sequential Port Fuel Injection
Check Engine Lamp
See Check Engine and Low Fuel Lamp: VRSC Models. The engine check lamp is located
inside the instrument cluster. Its purpose is to indicate whether or not the engine/engine
management system is operating normally. The engine lamp color is red.
The engine lamp normally comes on when the bike's ignition is first turned on and remains on for
approximately 4 seconds, as the engine management system runs a series of selfdiagnostics.
If the engine lamp comes on at any other time, see a HarleyDavidson dealer.
Low Fuel Lamp
See Check Engine and Low Fuel Lamp: VRSC Models. There is a low fuel warning lamp
within the instrument cluster. The low fuel lamp lights up to indicate that there is approximately 1
gallon (3.8 liters) of gasoline left in the tank. The low fuel lamp color is amber.
1. Check engine lamp
2. Low fuel lamp
Check Engine and Low Fuel Lamp: VRSC
Models
Gear Shift Lever
The clutch must be fully disengaged before attempting a
gear shift. Failure to fully disengage the clutch can result
in equipment damage. (00182a)
See Gear Shift Lever (Downshift): VRSC Models. The gear shift lever is located on the left
side of the motorcycle and is operated with the left foot. The transmission is a five speed
sequential gear box.
1. Push the gear shift lever all the way down (full stroke) to shift the transmission to the next
lower gear.
2. Lift the gear shift lever all the way up (full stroke) to shift the transmission to the next higher
gear.
NOTES:
Release the gear shift lever after each gear change.
The lever must return to its central position before another gear change can be made.
First gear is the last gear position that can be found by pushing the gear shift lever full stroke
downward.
Neutral is located between first and second gear. The green neutral indicator lamp on the dash
will illuminate when the transmission is in neutral.
To shift from first gear to neutral, lift the gear shift lever 1/2 of its full stroke.
When the motorcycle is standing still and the engine is not running, shifting gears requires a
different technique. Before shifting in this condition, move the motorcycle backward and forward
with the clutch fully disengaged (clutch lever pulled in). While maintaining slight pressure on the
shift lever, shift from one gear to another.
Even with the engine running and the motorcycle standing still, difficulty may be experienced in
shifting gears. This difficulty occurs because transmission gears are not turning and shifting parts
are not lined up to permit engagement.
When difficulty of shifting gears is experienced, do not
under any circumstances, attempt to force the shift. The
results of such abuse will be a damaged or broken shifter
mechanism. (00161a)
See Shifting Gears for more information.
Gear Shift Lever (Downshift): VRSC Models
Brake System
General
The rear brake pedal controls the rear wheel brake and is located on the motorcycle's right side.
Operate the rear brake pedal with the right foot.
The front brake hand lever controls the front wheel brake and is located on the right handlebar.
Operate the hand lever with the fingers of the right hand.
Do not position fingers between hand control lever and
handlebar grip. Improper hand positioning can impair
control lever operation and cause loss of vehicle control,
Some models are equipped with an antilock braking system.
NonABS Brake System
Apply brakes uniformly and evenly to prevent wheels from locking. Use front and rear brakes
equally for best results.
Do not apply brake strongly enough to lock the wheel. A
locked wheel will skid and can cause loss of vehicle
control, which could result in death or serious injury.
(00053a)
Antilock Brake System (ABS)
HarleyDavidson's AntiLock Brake System assists the rider in maintaining control when braking in
a straightline emergency situation. ABS operates independently on front and rear brakes to keep
the wheels rolling and prevent uncontrolled wheel lockups either on dry pavement or on slick
surfaces such as gravel, leaves or when riding in wet conditions.
ABS: How It Works
The ABS monitors sensors at the front and rear wheels to determine wheel speed. If the system
detects one or both wheels are slowing down too quickly, which indicates they are close to
locking, or if the deceleration rate does not match a criteria stored in memory, the ABS reacts.
The system rapidly opens and closes valves to modulate the brake caliper pressure utilizing only
the brake lever/pedal pressure being applied by the rider. During ABS activation, the system
provides the electronic equivalent of manually pumping the brakes and is capable of cycling up to
seven times per second.
The rider will recognize ABS activation by the slight pulsing sensation in the hand lever or the rear
brake pedal. The pulsing sensation may also be accompanied by a clicking sound from the ABS
module. Both are the result of normal operation. Refer to ABS Symptoms and Conditions.
ABS: How To Use
While an advantage in emergency braking, ABS is not a substitute for safe riding. The safest way
to stop a motorcycle is upright with both wheels straight.
HarleyDavidson ABS is a manual assist system. When in an emergency stopping situation,
maintain pressure on the brakes through all ABS events. Do not modulate or "pump" the brake
controls. The wheels won't lock until the end of the stop when motorcycle speed reaches
approximately four miles per hour and ABS is no longer needed.
ABS cannot prevent lockup of rear wheel due to engine
braking. ABS will not aid in cornering or on loose/uneven
surfaces. A locked wheel will skid and can cause loss of
vehicle control, which could result in death or serious
injury. (00362a)
More information is available at www.harleydavidson.com/abs.
ABS: Tires and Wheels
ABS motorcycles must always use tires and wheels that are the same as the original equipment.
The ABS monitors the rotational speed of the wheels through individual wheel speed sensors.
Changing to different diameter wheels or different sized tires can alter the rotational speed. This
can upset the calibration of the ABS and have an adverse effect on its ability to detect and
prevent uncontrolled wheel lockups. Tire inflation pressure that is significantly low also can have
an adverse effect.
ABS Symptoms and Conditions
SYMPTOM CONDITION
Pulsing Normal condition.
brake lever
or pedal
during an
ABS event
Clicking Normal condition.
sound
during an
ABS event
ABS lamp Normal condition key turned to IGNITION speed under 3 mph 5 km/h .
flashing
Perceived Normal condition most noticeable when braking with one brake (front only or rear
"surge" only). Result of a reduction in deceleration which can be caused by cracks or
while bumps in road, engine braking (high engine RPMs causing the rear wheel to slow
braking down), hard braking at slow speeds, and other conditions. This is due to ABS
modulating caliper brake pressure to prevent uncontrolled wheel lock.
Temporarily Normal condition engine braking (high engine RPMs causing the rear wheel to
stiff rear slow down) or down shifting can activate ABS. If applying the rear brake at the
brake pedal same time or immediately after, the ABS may be closing a valve to prevent
pressure to the rear brake. This is due to ABS modulating caliper brake pressure to
prevent uncontrolled wheel lock.
Tire chirp Normal condition depending on surface, tire can chirp without locking the wheel.
Black mark Normal condition depending on surface, tire can leave a black mark without
on locking the wheel.
pavement
Wheel lock Normal condition ABS will not activate on front wheel below 3 mph 5 km/h or on
at low rear wheel below 5 mph 8 km/h .
speed
Jiffy Stand
Always park motorcycle on a level, firm surface. An
unbalanced motorcycle can fall over, which could result in
The jiffy stand is located on the left side of the motorcycle and swings outward to support the
motorcycle for parking.
The jiffy stand locks when placed in the full forward (down)
position with vehicle weight on it. If the jiffy stand is not in
the full forward (down) position with vehicle weight on it,
the vehicle can fall over which could result in death or
Be sure jiffy stand is fully retracted before riding. If jiffy
stand is not fully retracted, it can contact the road surface
causing a loss of vehicle control, which could result in
Rear View Mirrors
Objects in mirrors are closer than they appear. Use caution
when judging distance of objects in mirrors. Failure to
judge correct distances could result in death or serious
injury. (00033a)
Your vehicle is equipped with two convex rear view mirrors.
This type of mirror is designed to give a much wider view to the rear than a flat mirror. However,
cars and other objects seen in this type of mirror will look smaller and farther away than they
actually are.
Use caution when judging the size or relative distance of objects seen in rear view mirrors.
Always adjust the rear view mirrors to clearly reflect the area behind the motorcycle before
riding.
NOTE:
Adjust mirrors so you can see a small portion of your shoulders in each mirror. This will help you
establish the relative distance of vehicles to the rear of your motorcycle.
Fuel Filler Cap: VRSC Models
See Fuel Filler Cap: VRSC Models. The fuel filler cap is located under the seat.
To open, turn the fuel filler cap counterclockwise and lift up. To close, turn the fuel filler cap
clockwise until it clicks. The ratchet action of the cap prevents overtightening.
See SAFE OPERATING RULES section and review safety procedures.
Do not spill fuel onto the motorcycle while refueling.
Immediately wipe up fuel spills on your motorcycle. Fuel
can cause damage to cosmetic surfaces. (00147b)
Use only unleaded fuel in catalytic converterequipped
motorcycles. Using leaded fuel will damage the emission
control system. (00150b)
Fuel Filler Cap: VRSC Models
Fork Lock: VRSC Models
Protect your vehicle against theft. After parking your
motorcycle, lock the steering head and ignition switch.
Failure to lock your motorcycle can result in theft and/or
equipment damage. (00491c)
See Fork Lock: VRSC Models. VRSC models have the fork lock incorporated in the steering
head on the right hand side.
Using the fork lock immediately after parking your motorcycle will discourage unauthorized use or
theft when parking your motorcycle.
1. Turn the fork to the full left position.
2. Insert the ignition key into the fork lock.
3. Push down on the fork lock switch and turn to the full clockwise position.
4. Remove the ignition key.
1. Lock
2. Unlock
Fork Lock: VRSC Models
Rear Shock Absorbers
General
The rear shock absorber spring preload can be adjusted for the weight the motorcycle is to carry
and has five preload graduations. Notice the adjustment settings as you turn the collar.
The average weight solo rider might use the extended spring preload position (adjustment setting
1 or 2).
Use the adjustment setting numbers as a reference for equal adjustment of shock absorbers on
both the right and left side of the motorcycle. A heavy solo rider might require additional preload
or pressure (adjustment setting 3).
Adding a passenger may require maximum preload (adjustment setting 5).
Adjustment
Be sure both shock absorbers are adjusted to same
preload position. Improper adjustment can adversely affect
stability and handling, which could result in death or
Do not turn the shock absorber adjustment collar
counterclockwise beyond adjustment setting 1. Doing so
may result in equipment damage. (00166a)
1. See Rear Shock Absorber Adjustment: VRSCF Model. Place a SPANNER WRENCH
9482075A (VRSCF) or SPANNER WRENCH 9470052C (other models) around the lower
collar of the shock absorber.
NOTE:
See Rear Shock Absorber Adjustment: VRSCAW/VRSCDX Models.
VRSCAW/VRSCDX models have a cover over the preload adjustment collar. Insert teeth on
spanner wrench into holes in the collar cover.
2. See Preload Adjustment. To adjust the rear shock absorber spring preload, turn the
spring adjusting cam to the desired position. When returning to offcam position, cams
should be backed off in opposite direction.
a. Turn the collar clockwise (toward higher numbers) to increase the preload.
b. Turn the collar counterclockwise to decrease the preload.
Rear Shock Absorber Adjustment: VRSCF Model
Rear Shock Absorber Adjustment: VRSCAW/VRSCDX Models
1. Minimum preload adjustment
2. Maximum preload adjustment
Preload Adjustment
License Plate Bracket: VRSCF Model
See License Plate Bracket: VRSCF Model. In some markets, the VRSCF model has a
convertible sidemounted license plate assembly, which includes an LEDilluminated lamp
module. The license plate must be in the extended position during operation. If LED lamp fails,
see a HarleyDavidson dealer for assembly replacement.
License Plate Bracket: VRSCF Model
Mirrors: VRSCF Model
See Mirror/Turn Signal Alignment: VRSCF Model. On the VRSCF model, the mirror stems
operate as front turn signals. Use the following procedure to properly align the front turn signals
and position the rear view mirrors.
NOTE:
See Mirror/Turn Signal Fasteners: VRSCF Model. Always loosen fasteners before changing
the position of the turn signals or mirrors. Simply pushing the mirror face or stem may cause
damage to the assembly.
1. See Mirror/Turn Signal Fasteners: VRSCF Model. Loosen the nut on the mirror stem.
Adjust the front turn signal so it is directed straight ahead, with the lighted surface facing the
forward direction of the vehicle as shown in Mirror/Turn Signal Alignment: VRSCF
Model.
2. Tighten nut to 6475 inlbs (7.38.5 Nm).
3. Loosen the screw on the rear of the mirror. Adjust the mirror to desired position (without
changing the orientation of the front turn signal).
4. Tighten screw to 3660 inlbs (4.16.8 Nm).
1. Front turn signal (perpendicular to forward direction of vehicle)
2. Mirror
Mirror/Turn Signal Alignment: VRSCF Model
1. Mirror screw
2. Mirror stem nut
Mirror/Turn Signal Fasteners: VRSCF
Model
HarleyDavidson Smart Security System
HarleyDavidson Smart Security System
Components
See Security Module w/Antenna (shown removed). The HarleyDavidson Smart Security
System (HDSSS) consists of a HandsFree Security Module (HFSM) (1) and a HandsFree
Antenna (2) mounted on the motorcycle, and a HandsFree Fob carried by the rider/passenger.
After parking the motorcycle, turn the ignition key to OFF and the Smart Security System will
automatically arm within five seconds. While armed, the starter and ignition are disabled and the
rider may leave the motorcycle knowing that the module will activate an alarm if someone tampers
with the ignition or attempts to move the motorcycle.
If the fob is present, the module will automatically disarm when the ignition key is turned to
IGNITION or ACCESS.
NOTE:
Do not relocate the module or the antenna on the motorcycle.
Options
Several options are available for the HarleyDavidson Smart Security System from the Harley
Davidson Genuine Motor Accessories and Motor Parts catalog. Options include:
Smart Siren and Smart Siren II.
Security Pager and Security Pager Receiver II.
Replacement Fobs.
See a HarleyDavidson dealer for details.
1. HandsFree Security Module
2. HandsFree Antenna
Security Module w/Antenna (shown
removed)
FCC Regulations
FCC ID: L2C0027TR IC ID: 3432A0027TR
FCC ID: L2C0028TR IC ID: 3432A0028TR
This device complies with Part 15 of the FCC Rules and with RSS210 of Industry Canada rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications not expressively approved by the party responsible for
compliance could void the user's authority to operate the equipment.
The term "IC:" before the radio certification number only signifies that Industry Canada technical
specifications were met.
HandsFree Fob
Fob Assignment
See HandsFree Fob: Smart Security System. HandsFree Fobs are electronically assigned
to the HarleyDavidson Smart Security System by a HarleyDavidson dealer so that the module
can recognize a fob's unique signal. Only two fobs can be assigned to the module at any one
time.
Replacement fobs can be purchased from a dealership but can only be assigned to the
motorcycle by a trained HarleyDavidson technician.
NOTES:
The reusable label found on the fob packaging lists the serial number of the fob. For
reference, fix the label to a blank "NOTES" page in the Owner's Manual.
The serial number of the fob is also found on the inside of the fob. See Fob Battery.
The module will arm only if the fob has been assigned by a HarleyDavidson dealer and a
Personal Identification Number (PIN) has been entered in the system. The PIN should be
recorded on the Personal Information page in the front of this Owner's Manual and on the
removable wallet card.
Should the rider misplace the fob or if the fob fails, the rider can refer to the wallet card and
use the PIN to manually disarm the system. Refer to Arming and Disarming and
Troubleshooting.
The PIN can easily be changed by the rider at any time. Refer to Personal Identification
Number (PIN).
HandsFree Fob: Smart Security System
Riding with a Fob
Always carry the fob when riding, loading, fueling, moving, parking or servicing the
motorcycle. Carry the fob in a convenient pocket.
Do not leave the fob attached to the handlebars or store the fob in a saddlebag or Tour
Pak®. Unintentionally leaving the fob with the motorcycle when it's parked prevents the
system from activating the alarm.
Do not ride with the fob stored in a metal case or with the fob closer than 3.0 in. 76 mm to a
cell phone, PDA, display or other electronic device. Any electromagnetic interference may
prevent the fob from disarming the system.
For added security, always lock the fork and remove the ignition key when parked. If the fob
is within range and the motorcycle is unlocked, tampering with the motorcycle will not
activate the alarm.
Personal Identification Number (PIN)
The Personal Identification Number (PIN) is a number that can be used to disarm the Harley
Davidson Smart Security System in case an assigned fob is misplaced, fails or if the fob and
module cannot communicate because of electromagnetic interference.
A PIN is a fivedigit number (19, no zeros).
Changing the PIN
To maintain security, the rider can change the PIN at any time. Refer to Changing the PIN.
Changing the PIN
STEP ACTION WAIT FOR CONFIRMATION NOTES
NO.
1 Select a 5digit (1 thru 9) PIN
and record on the wallet card
from Owner's Manual.
2 With an assigned fob present,
turn IGN key IGNITIONOFF
IGNITIONOFFIGNITION.
3 Press left turn signal switch 3
times.
4 Press right turn signal switch Turn signals will flash 3 times. See figure showing the
1 time and release. Current PIN will appear in odometer window with
odometer. The first digit will be PIN display.
flashing.
5 Enter first digit (a) of new PIN
by pressing left turn signal
switch a times.
6 Press right turn signal switch The new digit (a) will replace the
1 time and release. current in odometer window.
7 Enter second digit (b) of new
PIN by pressing left turn
signal switch b times.
8 Press right turn signal switch The new digit (b) will replace the
1 time and release. current in odometer window.
9 Enter third digit (c) of new PIN
switch c times.
10 Press right turn switch 1 time The new digit (c) will replace the
and release. current in odometer window.
11 Enter fourth digit (d) of new
PIN by pressing left turn
signal switch d times.
12 Press right turn switch 1 time The new digit (d) will replace the
13 Enter fifth digit (e) of new PIN
switch e times.
14 Press right turn switch 1 time The new digit (e) will replace the
15 Before the module rearms, The odometer will return to Turning the ignition
turn the ignition key to OFF. mileage. key to OFF stores the
new PIN in the
module.
1. Current PIN (example) on PIN Change
2. PIN Disarm
Odometer Windows PIN
Security Status Indicator
See Security Status Indicator: VRSC Models. The illuminated key icon in the speedometer
face indicates the status of the HarleyDavidson Smart Security System.
Armed: A key icon that blinks approximately every 3 seconds indicates that the system is
armed.
Disarmed: After the ignition/headlamp switch is turned to IGNITION and the system
disarms, the key icon will remain illuminated for approximately four seconds and then turn
off.
Service: A key icon that remains illuminated longer than four seconds indicates that service
of the module is required.
Security Status Indicator: VRSC Models
Arming and Disarming
Arming
When the motorcycle is parked and the ignition key is turned to OFF, the HarleyDavidson Smart
Security System arms automatically within five seconds if no motion is detected. Even when the
fob is present, the system will arm.
On arming, the turn signals will flash twice and the optional siren will chirp twice. While armed, the
key icon in the speedometer face will flash every three seconds.
NOTE:
International Models: The HFSM must be in the Chirp Mode for the siren to chirp on arming or
on disarming. See Siren Chirp Mode (Confirmation).
Disarming
Once disarmed, the rider may ride or move the motorcycle for parking, storage or service without
setting off the alarm.
Fob: An armed Smart Security System is automatically disarmed when the ignition key is turned
to IGNITION with the fob present.
When the module disarms, the optional siren will chirp once and the key icon will illuminate for a
solid four seconds and then turn off.
NOTE:
Any motion, like lifting the motorcycle up off of its jiffy stand, or turning the ignition key to
IGNITION and the module will electronically "poll" for the presence of the fob. If the fob is present,
the system disarms.
Personal Identification Number (PIN): If the fob is misplaced or if the present fob fails to
communicate with the module, the system can be disarmed with the Personal Identification
Number (PIN).
Disarming with a PIN
Do not turn handlebars, straddle seat or lift motorcycle off the jiffy stand. During a PIN disarm, if
the Smart Security System detects motorcycle motion the system will activate the alarm.
Entering a PIN to Disarm HarleyDavidson Smart Security System
STEP ACTION WAIT FOR CONFIRMATION NOTES
NO.
1 If necessary, verify the Should be recorded on wallet
current 5digit PIN. card.
2 Turn ignition key to
IGNITION.
3 Quickly (within 2 seconds Key icon flashes at fast rate. See figure showing the
of turning ignition key) hold In the odometer window, a odometer window with PIN
both turn signal switches in flashing dash will be followed display. Five dashes will
until confirmation. by four more dashes. appear in the odometer
window.
4 Enter first digit (a) in the The first digit (a) in the
PIN by pressing left turn odometer will be the first digit
switch a times. in the PIN.
5 Press right turn switch 1 The first digit is stored and Serves as enter key.
time. the dash will flash.
6 Enter second digit (b) in the The second digit (b) in the
PIN by pressing left turn odometer will be the second
switch b times. digit in the PIN.
7 Press right turn switch 1 The second digit is stored Serves as enter key.
time. and the next dash will flash.
8 Enter third digit (c) in the The third digit (c) in the
PIN by pressing left turn odometer will be the third
switch c times. digit in the PIN.
9 Press right turn switch 1 The third digit is stored and Serves as enter key.
time. the next dash will flash.
10 Enter fourth digit (d) in the The fourth digit (d) in the
PIN by pressing left turn odometer will be the fourth
switch d times. digit in the PIN.
11 Press right turn switch 1 The fourth digit is stored and Serves as enter key.
time. the next dash will flash.
12 Enter fifth digit (e) in the The fifth digit (e) in the
PIN by pressing left turn odometer will be the fifth digit
switch e times. in the PIN.
13 Press right turn switch 1 The fifth digit is stored. The Smart Security System is
time. key icon stops blinking. disarmed.
NOTES:
At any time during a PIN disarm, if the fob is brought within range of the motorcycle, the
Smart Security System will disarm when the module receives the coded signal from the fob.
If a mistake is made while entering PIN, wait two minutes before another disarming attempt.
The Smart Security System will remain disarmed until the ignition key is turned to OFF.
Arming with Hazard Warning 4Way Flashers On
If it should be necessary to leave a motorcycle parked along side a roadway, the hazard warning
fourway flashers can be turned ON and the Smart Security System armed.
1. Turn ignition key to IGNITION.
2. Simultaneously press both left and right turn signal switches to turn the fourway flashers
ON.
3. Turn the ignition key to OFF to arm the Smart Security System.
To turn hazard warning flashers OFF, turn the ignition key to IGNITION and simultaneously press
the left and right turn signal switches.
Alarm
Warnings
Once armed, if the motorcycle is moved or lifted up off of its jiffy stand or if the ignition key is
turned to IGNITION and the fob is not present, the alarm will warn the operator with three
alternate flashes of the turn signals and a chirp of the optional siren.
Within four seconds, if the motorcycle is back on its jiffy stand and no further motion is detected
and/or the ignition key is turned to OFF, the module will remain armed without activating the
alarm.
If the motorcycle motion continues or the ignition key is not turned back to OFF, the module will
issue a second warning four seconds after the first.
NOTE:
During warnings and alarms, the starter motor and the ignition circuits are disabled.
The Alarm
If the Smart Security System is still detecting motion and/or if the ignition key has not been turned
back to OFF after a second warning, the system will activate the alarm.
When activated, the Smart Security System will:
Alternately flash the four turn signals.
See Optional Smart Siren. Sound the optional siren.
Duration: The alarm will stop within 30 seconds and if no motion is detected, the alarm will not
restart.
However, if motorcycle motion continues the system will repeat the 30 second alarm and recheck
for motion. The alarm will repeat this 30 second alarm cycle for five minutes (10 cycles) or until
the alarm is deactivated.
NOTE:
The alarm will also activate the LED, vibration or audible modes of a HarleyDavidson Security
Pager. A pager can operate either in silent or in combination with an optional Smart Siren. The
range of a pager can be up to 0.5 mile 0.8 km . See a HarleyDavidson dealer for details.
Optional Smart Siren
Deactivate the Alarm
Key Fob: Bring the fob to the motorcycle. After the module identifies that the fob is present, the
system will terminate the alarm.
Siren Chirp Mode (Confirmation)
Chirpless Mode
In the chirpless mode, the siren does not chirp on arming or disarming.
NOTE:
Even when armed in the chirpless mode, the siren still chirps warnings on movement and will
activate the alarm through cycles.
Chirp Mode
On arming in the chirp mode, the siren responds with two chirps. When disarming, the siren
responds with a single chirp.
Switching Modes
Cycling quickly through two armings and disarmings will switch the system from either the
chirpless mode or the chirp mode to its opposite.
1. With the fob present, the ignition switch to ON and the system disarmed, turn the ignition
switch OFF.
2. When the system arms (2 flashes of turn signals), immediately turn the ignition switch to
ON.
3. Wait until the security lamp goes out, then immediately turn the ignition switch OFF.
4. When the system arms (2 flashes of turn signals), immediately turn the ignition switch to ON
and wait for system to disarm.
Transport Mode
It is possible to arm the security system without enabling the motion detector for one ignition
cycle. This allows the vehicle to be picked up and moved in an armed state, however, any attempt
to start the engine will trigger the alarm.
To Enter Transport Mode
1. Turn the Ignition Switch to IGNITION.
2. Set the Engine Stop Switch to OFF.
3. With an assigned fob within range, turn the Ignition Switch from IGNITION to ACC.
4. Simultaneously press both the left and the right turn signal switches. This must be done
within five seconds of turning the Ignition Switch to ACC.
5. After the turn signals flash once, turn the Ignition Switch to OFF and the module is armed.
6. Confirmation: Turn signal blinks three times when armed for one ignition cycle.
To Exit Transport Mode
Return the system to normal operation:
With the fob present, turn the Ignition Switch to IGNITION to disarm the HFSM. To cancel the
transport mode, set the Engine Stop Switch to RUN.
Storage and Service Departments
Long Term Parking
To maintain arming, store the fob beyond the range of the module. If the motorcycle is to be
moved while parked, have the fob present.
If the motorcycle will not be operated for several months, such as during the winter season, follow
the Owner's Manual instructions for storage. Refer to Motorcycle Storage: VRSC Models.
Service Departments
When the motorcycle is to be left at a HarleyDavidson dealer, there are two options:
1. Leave an assigned fob with the dealer.
2. To maintain possession of the fob, ask the dealer to disable the module for service (service
mode) before leaving the dealership.
Fob Battery
Replacing the Battery
Replace the key fob battery every year.
1. See HandsFree Fob Battery. Slowly turn a thin blade in the thumbnail slot (1) on the side
of the fob to separate the two halves.
2. Remove the battery (2) and discard.
NOTE:
Dispose of the old battery in accordance with local regulations.
3. Install a new battery (Panasonic 2032 or equivalent) with the positive (+) side down.
4. Align the two halves of the fob and snap together.
1. Thumbnail slot
2. Battery
3. Fob serial number
HandsFree Fob Battery
Power Disconnects
Optional Siren
On a power disconnect, to prevent the module from actuating the optional siren:
1. Verify that the fob is present.
2. Turn the ignition key to IGNITION.
3. Pull the main fuse from its holder or disconnect the battery.
Troubleshooting
Key Icon
If the system key icon stays illuminated while riding, see a HarleyDavidson dealer.
Fob
With the fob present, if the Smart Security System continues to actuate warnings and alarms, one
of the following can be the cause:
1. Electromagnetic Interference: Other electronic devices, power lines, or other
electromagnetic sources can cause the Smart Security System to operate inconsistently.
a. Verify that the fob is not in a metal enclosure or within 3.0 in. 76 mm of any other
electronic devices.
b. Place the fob on the seat and turn the ignition key to IGNITION. After the module
disarms, return the fob to a convenient location.
c. Move motorcycle at least 15 feet 5 m from the spot of interference.
2. Discharged Fob Battery: Use the PIN to disarm the module. Replace the battery. Refer to
Fob Battery.
3. A Damaged Fob: Use the PIN to disarm the motorcycle. Replacement fobs are available for
purchase from a HarleyDavidson dealer.
Siren
If the siren does not chirp two or three times on a valid arming command from the security
module, the siren is either in the Chirpless Mode, not connected, not working, or the siren
wiring was opened or shorted while the siren was disarmed.
If the siren is armed and the internal siren battery is dead, shorted, disconnected, or has
been charging for a period longer than 24 hours, the siren will respond with three chirps on
arming instead of two.
The internal siren battery may not charge if the vehicle's battery is less than 12.5 volts.
If the siren enters the selfdriven mode where it is powered from the siren's internal 9 volt
battery, the turn signal lamps may or may not alternately flash. If the security module
activates the siren, the turn signal lamps will alternately flash. If the siren has been armed
and a security event occurs, and the siren is in selfdriven mode, the siren will alarm for 20
to 30 seconds and then turn off for 5 to 10 seconds. This alarm cycle will be repeated ten
times if the siren is in the selfdriven mode.
Operation
Operating Recommendations: VRSC Models
Motorcycles are different from other vehicles. They
operate, steer, handle and brake differently. Unskilled or
improper use could result in loss of control, death or
serious injury. (00556c)
Take a rider training course.
Read Owner's Manual before riding, adding accessories or servicing.
Wear a helmet, eye protection and protective clothing.
Never tow a trailer.
Do not run the engine at extremely high RPM with clutch
disengaged or transmission in neutral. Running an engine
at high RPM can result in engine damage. (00177a)
The maximum recommended safe engine speed is 9000 RPM.
Do not idle engine unnecessarily for more than a few minutes with motorcycle standing still.
Do not exceed the maximum safe RPM specified below
under any conditions. Exceeding the maximum safe
engine RPM can result in equipment damage. (00248a)
NOTE:
The maximum recommended engine speed for VRSC model motorcycles is 9000 RPM.
If motorcycle will not be ridden for a period of three weeks or more with security system armed, it
is recommended to connect a Battery Tender to maintain battery charge. If security system will
not be armed, it is recommended that the 40 Amp maxifuse be removed. See Electrical
Protection: VRSC Models.
Use only Genuine HarleyDavidson Extended Life
Antifreeze and Coolant. Use of other coolants/mixtures
may lead to engine damage. (00179b)
Have the engine checked regularly and keep it well tuned. This applies particularly to a
motorcycle equipped with windshield and fairing.
When riding on wet roads, brake efficiency and traction are
greatly reduced. Failure to use care when braking,
accelerating or turning on wet roads can cause loss of
control, which could result in death or serious injury.
(00041a)
NOTES:
While the motorcycle is operating, electronically controlled cooling fans will turn on
periodically. This is normal operation.
When descending upon a long, steep grade, downshift and use engine compression
together with intermittent application of both brakes to slow the motorcycle.
Continuous use of brake causes overheating and reduced
efficiency, which could result in death or serious injury.
(00042a)
Do not coast for long distances with the engine off or
idling. The transmission is properly lubricated only when
the engine is running. Coasting long distances can result
in transmission damage. (00180b)
Using the clutch to slow the motorcycle when it is turned
off and rolling backwards can damage the power train.
(00562b)
Breakin Riding Rules: VRSC Models
The First 500 Miles (800 Kilometers)
The sound design, quality materials, and workmanship that are built into your new Harley
Davidson will give you optimum performance right from the start.
To allow your engine to wear in its critical parts, we recommend that you observe the riding rules
provided below for the first 500 miles (800 kilometers). Adherence to these suggestions will help
to assure good future durability and performance.
1. During the first 50 miles (80 kilometers) of riding, keep the engine speed below 5000 RPM in
any gear. Do not lug the engine by running or accelerating at very low RPM, or by running at
high RPM longer than needed for shifting or passing.
2. Up to 500 miles (800 kilometers), vary the engine speed and avoid operating at any steady
engine speed for long periods. Engine speed up to 7000 RPM in any gear is permissible.
3. Drive slowly and avoid fast starts at wide open throttle until the engine has warmed up.
4. Avoid lugging the engine by not running the engine at very low speeds in higher gears.
5. Avoid hard braking. New brakes need to be brokenin by moderate use for the first 200
miles (300 kilometers).
PreRiding Checklist: VRSC Models
riding your motorcycle. Failure to understand the
operation of the motorcycle could result in death or
Before riding your motorcycle at any time, make a general inspection to be sure it is in safe riding
condition.
1. Check the amount of fuel in the tank and add fuel if required.
Use care when refueling. Pressurized air in fuel tank can
force gasoline to escape through filler tube. Gasoline is
Stop the engine when refueling or servicing the fuel
system. Do not smoke or allow open flame or sparks near
gasoline. Gasoline is extremely flammable and highly
explosive, which could result in death or serious injury.
(00002a)
Do not spill fuel onto the motorcycle while refueling.
Immediately wipe up fuel spills on your motorcycle. Fuel
can cause damage to cosmetic surfaces. (00147b)
2. Adjust mirrors to proper riding positions.
3. Check the oil level. See Checking Oil Level: VRSC Models.
4. Check the coolant level. See Coolant Level.
5. Check the controls to be sure they are operating properly. Operate the front and rear
brakes, throttle, clutch and shifter.
6. Check steering for smoothness by turning the handlebars through the full operating range.
7. Refer to Tire Pressures: 2009 VRSC Models. Check tire condition and pressure.
Incorrect pressure will result in poor riding characteristics and can affect handling and
stability. Adhere to tire specifications for correct inflation pressures to use.
Be sure headlamp, tail and stop lamp and turn signals are
operating properly before riding. Poor visibility of rider to
other motorists can result in death or serious injury.
(00478b)
8. Check all electrical equipment and switches including the stop lamp, turn signals and horn,
for proper operation.
9. Check for any fuel, oil or hydraulic fluid leaks.
10. Check rear belt adjustment.
11. Service your motorcycle as necessary.
Jiffy Stand Interlock: International Models
Some international models are equipped with a jiffy stand interlock feature.
If the rider attempts to start the engine or pushes the starter button while the transmission is in
gear and the jiffy stand is down, then the jiffy stand interlock system will not permit the engine to
run. The message "SidE StAnd" will scroll across the odometer to indicate this to the rider.
Raising the jiffy stand (or putting the transmission in neutral) will permit the engine to run and
clear the message.
If the jiffy stand falls out of the fully retracted position while riding at speeds greater than 10 mph
15 km/h , then the jiffy stand interlock system will maintain engine operation and alert the rider
about this by illuminating the indicators (flash twice) and scroll the message "SidE StAnd" across
the odometer. The message will remain until the system detects the jiffy stand in the fully
retracted position again. The rider may continue to operate the vehicle while in this mode.
The rider may clear the text messages at any time by pressing the function switch once while the
vehicle is powered up.
NOTE:
If the operation of raising the jiffy stand and putting the transmission in gear is rapidly executed,
the jiffy stand bouncing off the frame could cause the jiffy stand interlock system to activate and
stop the engine.
Starting the Engine: VRSC Models
General
The engine should be allowed to run slowly for 3060
seconds. This will allow the engine to warm up and let oil
reach all surfaces needing lubrication. Failure to comply
can result in engine damage. (00181b)
Do not roll the throttle before starting. Rolling the throttle before starting the motorcycle is
unnecessary.
Starting
Shift transmission to neutral before starting engine to
prevent accidental movement, which could result in death
or serious injury. (00044a)
1. Turn ignition/headlamp key switch to IGNITION position. Do not roll the throttle.
NOTE:
The engine lamp will light for approximately 4 seconds and you will hear the fuel pump purr
for approximately 2 seconds as it operates to fill the fuel lines with gasoline.
2. See Right Handlebar Controls: VRSC Models. Turn the off/run switch to RUN position.
3. Squeeze the clutch lever in against the handgrip.
NOTE:
To activate the starting system, the clutch interlock circuitry requires the clutch be
disengaged, clutch lever pulled in against left handgrip, and/or the transmission be
shifted to the neutral position (green neutral lamp lit).
4. Raise the jiffy stand (required on international models).
5. Press the starter button to start the motorcycle.
6. When the engine has started, you can operate your motorcycle as you normally would after
raising the jiffy stand.
NOTES:
If the fuel tank becomes completely dry, it may take a few seconds longer to start the
motorcycle after filling the tank. It will not be necessary to take any extraordinary measures
before starting the motorcycle.
The ABS indicator lamp will remain on until vehicle is moving approximately 3 mph 5 km/h .
1. Engine off/run switch
2. Engine start switch
Right Handlebar Controls: VRSC Models
Stopping The Engine
1. Stop the engine by turning OFF the engine stop switch on the right handlebar.
2. Turn OFF the ignition/headlamp key switch. If the engine should be stalled or stopped in any
way, turn off the ignition/headlamp key switch at once to prevent battery discharge.
Shifting Gears
Getting Started
The clutch must be fully disengaged before attempting a
gear shift. Failure to fully disengage the clutch can result
in equipment damage. (00182a)
The shift pattern is first gear down, next four gears up.
NOTE:
Always start engine with transmission in neutral. Always start motorcycle forward motion in first
gear.
1. With motorcycle engine running and jiffy stand retracted, pull the clutch hand lever in against
handlebar grip to fully disengage clutch.
2. Press the foot shift lever down to end of its travel and release. The transmission is now in
first gear.
3. To start forward motion, ease out the clutch lever slowly and at the same time, open throttle
gradually.
Upshift (Acceleration)
Refer to Upshift (Acceleration) Gear Speeds: VRSC Models. Engage second gear after the
motorcycle has reached at the appropriate shifting speed.
Upshift (Acceleration) Gear Speeds: VRSC Models
GEAR CHANGE MPH KPH

First to second 15 25
Second to third 25 40
Third to fourth 35 55
Fourth to fifth 45 72
1. Close the throttle.
2. Disengage the clutch (pull clutch lever in).
3. See Gear Shift Lever (Upshift): VRSC Models. Lift the gear shift lever up to the end of
its travel and release.
4. Ease out the clutch lever and gradually open the throttle.
5. Repeat the previous steps to engage third, fourth, and fifth gears.
NOTES:
Disengage the clutch completely before each gear change.
Partially close the throttle so the engine will not drag when clutch is again engaged (clutch
lever released).
Gear Shift Lever (Upshift): VRSC Models
Downshift (Deceleration)
Do not downshift at speeds higher than those listed in the
Changing Gear Speeds table. Shifting to lower gears when
speed is too high can cause the rear wheel to lose traction
and lead to loss of vehicle control, which could result in
Gear shift pattern is first gear down; next four gears up. Refer to Downshift (Deceleration)
Gear Speeds: VRSC Models for shifting speeds.
Downshift (Deceleration) Gear Speeds: VRSC Models
GEAR CHANGE MPH KPH

Fifth to fourth 40 65
Fourth to third 30 50
Third to second 20 30
Second to first 10 15
NOTE:
The shifting points shown in the tables are recommendations. Vehicle owners may determine that
their own individual shifting patterns may differ than those stated and are additionally appropriate
for individual riding styles.
See Gear Shift Lever (Downshift): VRSC Models. When engine speed decreases, as in
climbing a hill or running at a reduced speed, shift to the next lower gear while partially closing the
throttle so the engine accelerates as soon as the clutch lever is released.
NOTES:
Disengage the clutch completely before each gear change.
Partially close the throttle so the engine will not drag when clutch is again engaged (clutch
lever released).
Shift to neutral before stopping engine. Shifting
mechanism can be damaged by shifting gears while
engine is stopped. (00183a)
The gear shifter mechanism permits shifting the transmission to neutral from either first or second
gear.
Gear Shift Lever (Downshift): VRSC Models
Maintenance and Lubrication
Safe Operating Maintenance: VRSC Models
Good maintenance means a safe machine. A careful check of certain equipment must be made
after periods of storage and frequently between the regular service intervals to determine if
additional maintenance is necessary.
Check the following items:
1. Tires for correct pressure, abrasions or cuts.
2. Drive belt for proper tension.
3. Brakes, steering and throttle for responsiveness.
4. Brake fluid level and condition. Hydraulic lines and fittings for leaks. Also, check brake pads
and discs for wear.
5. Throttle cables for fraying or crimping and free operation.
6. Engine oil level.
7. Engine coolant level.
8. Clutch fluid level.
9. Headlamp, tail lamp, brake lamp and directional lamp operation.
Breakin Maintenance
NOTE:
The performance of new motorcycle initial service is required to keep your new motorcycle
warranty in force and to assure proper emissions system operation.
Refer to Regular Service Intervals: 2009 VRSC Models. After a new motorcycle has been
ridden its first 1000 miles 1600 kilometers , it should be taken to an authorized HarleyDavidson
dealer for initial service operations.
Engine Lubrication
Do not switch lubricant brands indiscriminately because
some lubricants interact chemically when mixed. Use of
inferior lubricants can damage the engine. (00184a)
Engine oil is a major factor in the performance and service life of the engine. Always use the
proper grade of oil for the lowest temperature expected before the next scheduled oil change.
Refer to Recommended Engine Oils: VRSC Models. Your authorized dealer has the proper oil
to suit your requirements.
If it is necessary to add oil and HarleyDavidson oil is not available, use an oil certified for diesel
engines. Acceptable diesel engine oil designations include: CF4, CG4, CH4 and CI4.
The preferred viscosities for the diesel engine oils in descending order are: 20W50, 15W40 and
10W40.
At the first opportunity, see an authorized dealer to change back to 100 percent HarleyDavidson
oil.
Recommended Engine Oils: VRSC Models
HARLEY VISCOSITY HARLEY LOWEST AMBIENT COLD WEATHER

DAVIDSON DAVIDSON TEMPERATURE STARTS BELOW
TYPE RATING
50° F (10° C)
HD Multigrade SAE HD 360 Below 40° F (4° C) Excellent
10W40
HD Multigrade SAE HD 360 Above 40° F (4° C) Good
20W50
Checking Oil Level: VRSC Models
NOTE:
This engine has a wet sump, an integral transmission, gear driven primary drive and wet clutch.
This design allows engine oil in the sump to be used to lubricate the engine, transmission and
primary drive. The clutch and primary drive are housed on the right side of the engine.
Oil level cannot be accurately measured on a cold engine.
For preride inspection with the motorcycle upright (not
leaning on jiffy stand) on level ground, the oil should
register approximately at the midpoint of the crosshatch
area on the dipstick when the engine is cold. Do not add
oil to bring the level to the full mark on a cold engine.
(00186b)
See Dipstick Location: VRSCF Model (VRSCF) and Dipstick Location: VRSCAW/VRSCDX
Models (other models). On VRSCF model, the dipstick is located on the right side in the clutch
cover. On other models, the dipstick is located on left side at front of engine.
Cold Engine Oil Level Check
Check the oil level with the engine COLD as follows:
1. Stand the motorcycle upright (not leaning on the jiffy stand) on a level surface.
2. See Dipstick Location: VRSCAW/VRSCDX Models. Unscrew the oil filler cap (with
attached dipstick) by turning the filler cap counterclockwise. Remove the filler cap and
dipstick and wipe the dipstick clean.
3. Screw the filler cap into the engine. Make sure the cap is fully seated on the crankcase.
4. See Engine Oil Level: VRSC Models. Remove the filler cap again and check the oil level
on the dipstick.
5. If the oil level is below the midpoint of the crosshatch area on the dipstick, add enough
HarleyDavidson oil to bring the level up to the midpoint of the crosshatch area shown.
Do NOT operate the engine when the oil level is below the
add mark on the dipstick at operating temperature. Engine
damage could result. (00493b)
To avoid overfilling the oil sump, wait approximately three
minutes after adding oil before checking the oil level with
the dipstick. An overfilled sump can cause engine
damage. (00188a)
Dipstick Location: VRSCF Model
Dipstick Location: VRSCAW/VRSCDX Models
1. Full mark
2. Add mark. Do NOT operate the engine when the oil level is below the add mark at
operating temperature.
Engine Oil Level: VRSC Models
Hot Engine Oil Level Check
Check the oil level with the engine at normal operating temperature as follows:
1. Stop the engine and allow the oil to drain into the sump for about two minutes.
2. Stand the motorcycle upright (not leaning on the jiffy stand) on a level surface.
3. See Dipstick Location: VRSCAW/VRSCDX Models. Unscrew the oil filler cap (with
attached dipstick) by turning the filler cap counterclockwise. Remove the filler cap and
dipstick and wipe the dipstick clean.
4. Screw the filler cap into the engine. Make sure the cap is fully seated on the crankcase.
5. See Engine Oil Level: VRSC Models. Remove the filler cap again and check the oil level
on the dipstick.
6. If the oil level is below the FULL mark on the dipstick, add enough HarleyDavidson oil to
bring the level up to the FULL mark shown in Engine Oil Level: VRSC Models.
NOTE:
The engine will require a longer warmup period in colder weather.
Do not allow hot oil level to fall below Add/Fill mark on
dipstick. Doing so can result in equipment damage and/or
equipment malfunction. (00189a)
Do not overfill oil sump. Doing so can result in oil
carryover to the air cleaner leading to equipment damage
and/or equipment malfunction. (00191a)
Check the engine oil supply at each complete fuel refill.
Refer to Regular Service Intervals: 2009 VRSC Models. The oil should be changed
according to the Regular Service Intervals in the Maintenance Schedule in normal service at
warm or moderate temperatures.
Oil change intervals should be shorter in cold weather. See Winter Lubrication.
The oil ADD mark is 1/2 quart (0.473 liters) to full.
Refer to the vehicle's service manual or see a HarleyDavidson dealer for proper procedures on
draining the oil.
NOTE:
Dispose of oil in accordance with local regulations.
Changing Oil and Oil Filter: VRSC Models
See Applying Thin Oil Film. The oil filter is located on an oil filter mount in front of the engine.
Be sure that no lubricants or fluids get on tires, wheels or
brakes when changing fluid. Traction can be adversely
affected, which could result in loss of control of the
motorcycle and death or serious injury. (00047d)
VRSC vehicles require a premium oil filter (Part No. 6379301K).
1. See Oil Drain Plug: VRSC Model. Loosen the oil drain plug and completely drain the oil.
2. Remove the oil filter using an OIL FILTER WRENCH HD42311 .
NOTES:
Removal of lower radiator support may make oil filter access easier.
Dispose of oil and oil filter in accordance with local regulations.
3. Clean the filter gasket contact surface on the mounting plate (the surface should be smooth
and free of any debris or old gasket material).
4. See Applying Thin Oil Film. Apply a thin film of oil to the gasket contact surface on the
mounting plate, gasket and new oil filter.
5. Screw the filter onto the adapter until the gasket contacts the plate surface, then apply
another 2/31 full turn.
6. See Oil Drain Plug: VRSC Model. Install the engine oil drain plug. Tighten the drain plug
to 2230 ftlbs (3040 Nm).
7. Refer to Capacities: 2009 VRSC Models. Fill the engine with the recommended amount
of oil.
1. Thin oil film ONLY
2. Oil filter
3. Mounting plate
Applying Thin Oil Film
Oil Drain Plug: VRSC Model
Winter Lubrication
In colder climates, the engine oil should be changed often. If motorcycle is used frequently for
short trips, less than 15 miles 24 kilometers , in ambient temperatures below 60° F 16° C , oil
change intervals should be reduced to 1500 miles 2400 kilometers . Motorcycles used only for
short runs must have a thorough tank flushout before new oil is put in. The tank flushout should
be performed by an authorized dealer or qualified technician.
NOTE:
The further below freezing the temperature drops, the shorter the oil change interval should be.
Water vapor is a normal byproduct of combustion in any engine. During cold weather operation,
some of the water vapor condenses to liquid form on the cool metal surfaces inside the engine. In
freezing weather this water will become slush or ice and, if allowed to accumulate too long, may
block the oil lines and cause damage to the engine.
If the engine is run frequently and allowed to thoroughly warm up, most of this water will become
vapor again and will be blown out through the crankcase breather.
If the engine is not run frequently and allowed to thoroughly warm up, this water will accumulate,
mix with the engine oil and form a sludge that is harmful to the engine.
Coolant Level
GENUINE HARLEYDAVIDSON EXTENDED LIFE ANTIFREEZE & COOLANT (Part No. 99822
02) provides protection to 34° F 36.7° C . In climates where the temperature falls below 34° F
36.7° C , consult a local HarleyDavidson dealer for the proper mixture.
If you find yourself in a location where Genuine HarleyDavidson Extended Life Antifreeze &
Coolant is not available, you may use a 5050 mixture of deionized water and Ethylene Glycol
based Antifreeze.
Deionized water must be used with the antifreeze in the
cooling system. Hard water can cause scale accumulation
in water passages which reduces cooling system
efficiency, leading to overheating and engine damage.
(00195a)
Checking Coolant Level in Expansion Tank
1. Open the seat.
2. On VRSCF model, remove front side covers. See Front Side Covers: VRSCF Model.
3. See Airbox Cover: VRSC Models. Remove the airbox cover by turning the bailhead
fastener 1/4 turn counterclockwise. Pull the airbox cover away from the front locating holes.
(00091a)
At operating temperature, the radiator and oil cooler
contain hot fluids. Contact with the radiator or oil cooler
can result in minor or moderate burns. (00141a)
4. See Coolant Expansion Tank: VRSC Models. Check coolant level in expansion tank with
coolant cold and motorcycle on jiffy stand.
Coolant mixture contains toxic chemicals, which may be
fatal if swallowed. If swallowed, do not induce vomiting;
call a physician immediately. Use in a well ventilated area.
Irritation to skin or eyes can occur from vapors or direct
contact. In case of skin or eye contact, flush thoroughly
with water and go to hospital, if necessary. Dispose of
used coolant according to federal, state and local
regulations. (00092a)
5. If level is below "COLD FULL" line on tank, remove cap from expansion tank by using pull
tab and add HarleyDavidson Extended Life Antifreeze & Coolant until fluid level reaches the
"COLD FULL" line.
NOTE:
Genuine HarleyDavidson Extended Life Antifreeze & Coolant is prediluted and ready to
use fullstrength. Do NOT add water.
6. Replace the cap on the expansion tank.
7. Reinstall the airbox cover. Secure the cover by turning the bailhead fastener 1/4 turn
clockwise.
8. On VRSCF model, install front side covers. See Front Side Covers: VRSCF Model.
NOTE:
If the coolant expansion tank is empty when the engine is cold, it is possible that air has
been drawn into the cooling system. The system must be purged of any trapped air and
refilled with coolant. See the VRSC service manual for instructions on the correct procedure.
Clean the inlet surface of the radiator regularly. Leaves
and other debris can collect on the radiator surface and
degrade radiator performance which could lead to engine
overheating and engine damage. (00197c)
1. Airbox cover
2. Bailhead fastener
Airbox Cover: VRSC Models
1. Cold full line
2. Expansion tank cap
Coolant Expansion Tank: VRSC Models
Rear Drive Belt: VRSC Models
The inner tooth surface of the secondary belt has a thin coating of polyethylene lubricant. During
initial operation, this coating will wear off as it is burnished into the belt fabric. This is a normal
condition and not an indication of belt wear.
Refer to Regular Service Intervals: 2009 VRSC Models. Belt tension is set at the factory and
should be checked after the first 1000 miles 1600 kilometers and at regular intervals thereafter.
NOTE:
See Belt Deflection Window: VRSC Models. Belt deflection window on the debris deflector is
graduated in 2.0 mm increments.
See Check Belt Deflection: VRSC Models. Check belt tension with motorcycle cold, standing
upright, transmission in neutral and no rider on the motorcycle. Use the BELT TENSION GAUGE
HD35381 to apply 10 lbs. 4.5 kg of force at the midpoint of the bottom belt strand.
Belt deflection should be 8 mm. If belt tension adjustment is necessary, see a HarleyDavidson
dealer or follow the instructions given in the applicable Service Manual.
Check rear brake caliper position on rear brake disc. Disc should run true within brake caliper.
Be sure wheel and brake caliper are aligned. Riding with a
misaligned wheel or brake caliper can cause the brake disc
to bind and lead to loss of control, which could result in
1. Transmission sprocket
2. Rear wheel sprocket
3. Force of 10 lbs (4.5 kg)
4. Belt deflection
Check Belt Deflection: VRSC Models
1. Rear drive belt
2. Deflection graduations in 2.0 mm increments
Belt Deflection Window: VRSC Models
Chassis Lubrication
Refer to Regular Service Intervals: 2009 VRSC Models for all maintenance schedules.
1. Use recommended special purpose grease for steering head bearings. Use a multipurpose
chassis grease for other applications.
2. Remove and lubricate handlebar throttle control grip sleeve with fresh graphite at proper
intervals.
3. Lubricate throttle control cables and clutch control cable at proper intervals.
4. Lubricate front brake hand lever and clutch control hand lever only if necessary.
5. Inspect rear fork pivot shaft bearings.
6. Pack the steering head bearings with fresh grease at proper intervals.
7. Lubricate the jiffy stand mechanism with LOCTITE AEROSOL ANTISEIZE at proper
intervals.
NOTE:
For model specific information regarding the chassis lubrication, refer to the appropriate Service
Manual or see a HarleyDavidson dealer.
Oil Applications
Refer to Regular Service Intervals: 2009 VRSC Models for all control connections and parts.
Vehicle should be oiled at regular intervals, particularly after washing motorcycle or driving in wet
weather.
Front Fork Oil
Refer to Regular Service Intervals: 2009 VRSC Models. Have a HarleyDavidson dealer
drain the front fork oil and refill at proper intervals. If fork does not appear to be working properly
or an appreciable amount of oil leakage should develop, see a HarleyDavidson dealer. If there is
insufficient oil in either side of fork, the rebound action will be incorrect.
Fuel Filter
Fuel injected motorcycles have a fuel filter attached to the fuel pump.
NOTE:
For model specific information regarding fuel filter maintenance, refer to the appropriate Service
Clutch: VRSC Models
Squeezing the left hand lever causes the clutch master cylinder to actuate and apply pressure to
the clutch actuation cylinder mounted in the engine right side cover. The actuation cylinder piston
extends and contacts the clutch release bearing to release the clutch.
D.O.T. 4 brake fluid will damage painted and body panel
surfaces it comes in contact with. Always use caution and
protect surfaces from spills whenever brake work is
performed. Failure to comply can result in cosmetic
damage. (00239b)
Refer to Regular Service Intervals: 2009 VRSC Models. Check the fluid level as follows:
1. Stand the motorcycle upright (not leaning on the jiffy stand) on a level surface, so the top of
the clutch master cylinder is level.
2. See Clutch Master Cylinder Reservoir. Clean all dirt and debris from the clutch master
cylinder cover (1). Remove the two clutch master cylinder cover screws (2) and remove the
cover.
3. Verify the fluid level in the clutch master cylinder reservoir is at the FULL LEVEL mark at the
top of the ledge on the rear inside wall of the reservoir. If the fluid level is low, add D.O.T. 4
HYDRAULIC BRAKE FLUID (Part No. 9995399A) approved for clutch system use and
available from a HarleyDavidson dealer.
NOTE:
Do not overfill the clutch master cylinder reservoir. As the clutch friction discs wear, the
piston in the clutch cylinder will force fluid back into the reservoir which could cause fluid
overflow.
D.O.T. 4 hydraulic brake fluid is used in the hydraulic
clutch. Do not use other types of fluids as they are not
compatible and could cause equipment damage. (00353a)
Do not allow dirt or debris to enter the master cylinder
reservoir. Dirt or debris in the reservoir can cause
improper operation and equipment damage. (00205c)
Direct contact of D.O.T. 4 brake fluid with eyes can cause
irritation. Avoid eye contact. In case of eye contact flush
with large amounts of water and get medical attention.
Swallowing large amounts of D.O.T. 4 brake fluid can
cause digestive discomfort. If swallowed, obtain medical
attention. Use in well ventilated area. KEEP OUT OF
REACH OF CHILDREN. (00240a)
4. Inspect the clutch master cylinder cover gasket for rips, cuts, cracks, or other signs of
damage. Replace the gasket if necessary. Carefully place the cover and cover gasket on the
master cylinder reservoir and secure with the two cover screws. Tighten the screws to 68
inlbs (0.680.90 Nm).
NOTE:
If the fluid level in the clutch master cylinder reservoir is correct but the clutch does not
operate properly, refer to the VRSC Service Manual or see a HarleyDavidson dealer for
service.
1. Cover
2. Screws (2)
Clutch Master Cylinder Reservoir
Front Fork Bearings
Adjustments to front fork bearings should be performed by
a HarleyDavidson dealer. Improperly adjusted bearings
can adversely affect handling and stability, which could
Refer to Regular Service Intervals: 2009 VRSC Models. Check front fork for proper bearing
adjustment and lubricate bearings at proper intervals.
With motorcycle front end raised off the floor, be sure front fork turns freely without any binding or
interference and that there is no appreciable front to rear fork shake indicating excessive bearing
looseness. Steering head bearings should be adjusted according to Service Manual procedure, if
necessary.
Rear Fork Pivot Shaft
Refer to Regular Service Intervals: 2009 VRSC Models. Check the tightness of the rear fork
pivot shaft fastener at proper intervals.
NOTE:
For model specific information regarding the rear fork pivot shaft, refer to the appropriate Service
Brakes: VRSC Models
Inspect brake pads for wear at service maintenance
intervals. If you ride under adverse conditions (steep hills,
heavy traffic, etc.), inspect more frequently. Excessively
worn brake pads can lead to brake failure, which could
damage. (00239b)
NOTES:
Master cylinder cover specifies correct brake fluid.
When adding or changing brake fluid, be sure to use only the type specified for your
motorcycle.
Use only HarleyDavidson D.O.T. 4 HYDRAULIC BRAKE FLUID (Part No. 9995399A).
HarleyDavidson has provided your new motorcycle with the optimum brake pad friction material
available. It is selected to give the best performance possible under dry, wet and high operating
temperature conditions. It exceeds all regulatory requirements currently in effect. However, during
some braking conditions you may experience noise. This is normal for this friction material.
Refer to Regular Service Intervals: 2009 VRSC Models for brake system inspection
intervals.
NOTE:
The rear brake master cylinder fluid level can also be viewed with a flashlight through back area
of radiator cover trim making radiator cover removal unnecessary.
To prevent accidental vehicle startup, which could cause
death or serious injury, remove main fuse before
proceeding. (00251b)
1. Fastener
2. Cover trim
3. Radiator assembly
Removing Right Side Radiator Cover Trim
Rear Brake Master Cylinder Reservoir: VRSC Models
1. Check the fluid level in the rear brake master cylinder reservoir.
a. See Removing Right Side Radiator Cover Trim. Remove the fastener that
secures the radiator cover side trim. Gently pull the bottom of the side trim outward, lift
up on the trim to detach it from its upper attachment point and remove it from the
motorcycle.
b. See Rear Brake Master Cylinder Reservoir: VRSC Models. Verify the fluid level
in the rear brake master cylinder reservoir is 1/2 in. 12.7 mm below the top of the
reservoir, as viewed through the translucent plastic case of the reservoir.
c. If the level is low, clean all dirt and debris from the reservoir cover. Remove the two
reservoir cover screws and remove the cover. Add D.O.T. 4 HYDRAULIC BRAKE
FLUID (Part No. 9995399A) which is available from a HarleyDavidson dealer.
Replace the reservoir cover and cover fasteners. Tighten the fasteners to 68 inlbs
(0.680.90 Nm).
d. Carefully reinstall the radiator cover side trim and fastener. Tighten the fastener to
26.535.3 inlbs (34 Nm).
2. Check the fluid level in the front brake master cylinder reservoir.
a. Stand the motorcycle upright (not leaning on the jiffy stand) on a level surface, so the
top of the front brake master cylinder is level.
b. See Handlebar Controls: VRSC Models. Clean all dirt and debris from the front
brake master cylinder cover. Remove the two master cylinder cover screws and
remove the cover.
c. Verify the fluid level in the front brake master cylinder reservoir is 0.2 in. 5 mm below
the reservoir top. If the fluid level is low, add D.O.T. 4 HYDRAULIC BRAKE FLUID
(Part No. 9995399A) which is available from a HarleyDavidson dealer.
d. Replace reservoir cover and cover fasteners. Tighten fasteners to 68 inlbs (0.81.2
Nm).
NOTE:
Use only D.O.T. 4 HYDRAULIC BRAKE FLUID (Part No. 9995399A) approved for brake
system use and available from a HarleyDavidson dealer.
damage. (00239b)
Inspect brake pads for wear at service maintenance
intervals. If you ride under adverse conditions (steep hills,
heavy traffic, etc.), inspect more frequently. Excessively
worn brake pads can lead to brake failure, which could
3. Check the brake discs for wear.
Always replace brake pads in complete sets for correct
and safe brake operation. Improper brake operation could
Brakes are a critical safety component. Contact a Harley
Davidson dealer for brake repair or replacement.
Improperly serviced brakes can adversely affect brake
performance, which could result in death or serious injury.
(00054a)
4. See Brake Friction Material. Visual inspection of brake pads can be made without
removing the caliper by viewing the lower area of each caliper with the aid of a flashlight.
Replace the brake pads if the brake friction material is 0.016 in. 0.4 mm or less above the
backing plate.
Perform routine scheduled brake maintenance. Lack of
maintenance at recommended intervals can adversely
affect brake performance, which could result in death or
NOTES:
If the brake pad friction material is 0.016 in. 0.4 mm thick or less, the pads must be
replaced immediately.
Always replace brake pads in pairs.
The rear brake outer pad on all models can be measured from the caliper bracket side using a
thin plastic 6 in. 152 mm rule.
Place the rule against the brake disc through the space alongside the caliper. If friction material
measures less than 0.016 in. 0.4 mm , replace both brake pads immediately.
1. Front brake bottom view
2. Rear brake top view
Brake Friction Material
Tires: VRSC Models
Do not inflate tire beyond maximum pressure as specified
on sidewall. Over inflated tires can blow out, which could
Refer to Tire Pressures: 2009 VRSC Models. Be sure to keep tires properly inflated.
Follow the data for correct cold tire inflation pressures.
Check before riding when tires are cold.
Do not overinflate tires.
Match tires, tubes, air valves and caps to the correct wheel
rim. Contact a HarleyDavidson dealer. Mismatching can
result in damage to the tire bead, allow tire slippage on the
rim or cause tire failure, which could result in death or
Check inflation pressure and inspect the tread for punctures, cuts breaks, etc., at least
weekly if in daily use or before each trip if used occasionally.
NOTE:
The VRSC features performanceoriented tires. These tires require more frequent inspection and
may require more frequent replacement than HarleyDavidson touring model tires.
Refer to Tire Sizes: 2009 VRSC Models. Same original equipment tires should be used. Other
tires may not fit correctly, could adversely affect handling and may be hazardous to use.
Tires are a critical safety component. Contact a Harley
Davidson dealer for tire repair or replacement. Improper
tire service can adversely affect stability and handling,
Replace punctured or damaged tires. In some cases, small
punctures in the tread area may be repaired from within
the demounted tire by a HarleyDavidson dealer. Speed
should NOT exceed 50 mph (80 km/h) for the first 24 hours
after repair, and the repaired tire should NEVER be used
over 80 mph (130 km/h). Failure to follow this warning
Striking an object, such as a curb, can cause internal tire
damage. If an object is struck, remove and inspect both
the inside and outside of the tire. A damaged tire can
Tire Replacement
Inspection
HarleyDavidson tires are equipped with wear bars that run
horizontally across the tread. When wear bars become
visible and only 1/32 in. (0.8 mm) tread depth remains,
replace tire immediately. Using a worn tire can adversely
serious injury. Use only HarleyDavidson approved
replacement tires. (00090b)
See Tire Sidewall: VRSC Models. Arrows on tire sidewalls pinpoint location of wear bar
indicators.
Tread wear indicator bars will appear on tire tread surfaces when 1/32 in. 0.8 mm or less of tire
tread remains. See Tread Surface Wear Bar (Typical): VRSC Models. Always replace tires
before the tread wear indicator bars appear.
When To Replace Tires
New tires are needed if any of the following conditions exist:
1. Tread wear indicator bars become visible on the tread surfaces.
2. Tire cords or fabric become visible through cracked sidewalls, snags or deep cuts.
3. A bump, bulge or split in the tire.
4. Puncture, cut or other damage to the tire that cannot be repaired.
Tire Sidewall: VRSC Models
Tread Surface Wear Bar (Typical): VRSC
Models
Spark Plugs/Coils: VRSC Models
Refer to Regular Service Intervals: 2009 VRSC Models. Check the spark plugs at proper
mileage intervals.
Do NOT pull on any electrical wires. Pulling on electrical
wires may damage the internal conductor causing high
resistance, which may result in minor or moderate injury.
(00168a)
Before installing spark plugs, the gap should be checked and adjusted if necessary to 0.035 in.
(0.89 mm).
Be sure your motorcycle has the correct spark plug. Use a 10R12A spark plug.
Spark plugs must be tightened to the torque specified for proper heat transfer. Tighten spark
plugs to 17 ftlbs (23 Nm) per spark plug.
NOTES:
If a torque wrench is not available, tighten the spark plugs finger tight; then tighten an
additional one quarter turn with a spark plug wrench.
The VRSC is equipped with plugtop coils. To inspect the spark plugs, the coils must be
removed. Consult the VRSC Service Manual for the proper service procedure.
Shock Absorbers
Refer to Regular Service Intervals: 2009 VRSC Models. Inspect shock absorbers and rubber
bushings for leaks and bushing deterioration at proper intervals.
Ignition
The engine in your motorcycle has been designed specifically to achieve optimum fuel economy
within exhaust emission controls. Factory programmed ignition characteristics provide maximum
engine performance and driveability.
Front Side Covers: VRSCF Model
Removal
1. See Front Side Cover Screws: VRSCF Model. Remove five screws from front side
cover.
2. Lift side cover slightly to disengage mounting pin from bottom of side cover. Pull side cover
from frame.
Installation
1. See Front Side Cover Screws: VRSCF Model. Orient the air inlet toward the front of the
vehicle and align grommet in side cover with the mounting pin on frame. Press side cover to
engage mounting pin.
2. Install five screws with washers and tighten to 36.360.2 inlbs (4.16.8 Nm).
Front Side Cover Screws: VRSCF Model
Air Cleaner: VRSC Models
Refer to Regular Service Intervals: 2009 VRSC Models. The engine air cleaner is a
paper/wire mesh air filter element. Inspect the filter element. Inspect more often under dusty
conditions. Remove the air cleaner as follows:
1. Open seat.
2. On VRSCF model, remove front side covers. See Front Side Covers: VRSCF Model.
3. See Airbox Cover: VRSC Models. Remove the airbox cover by turning the bailhead
fastener 1/4 turn counterclockwise. Pull the airbox cover away from the front locating holes.
4. See Airbox Top: VRSC Models. Remove electrical connector (3) by pushing down on bail
wire to unlock. The airbox top is retained by eight clips, three per side, one at the rear and
one in the front under the snorkel. Release the clips and remove the airbox top.
1. Airbox cover
2. Bailhead fastener
Airbox Cover: VRSC Models
1. Airbox top
2. Mounting clips
3. Electrical connector
Airbox Top: VRSC Models
5. See Air Cleaner Assembly: VRSC Models. Unscrew the wing nut securing the air
cleaner cap. Remove the air cleaner cap and paper/wire mesh air filter element.
To prevent objects from falling down the velocity stacks,
temporarily reinstall the air cleaner cap. (00208a)
6. Wash the paper/wire mesh air filter element in luke warm water with a mild detergent. Rinse
thoroughly.
Compressed air can pierce the skin and flying debris from
compressed air could cause serious eye injury. Wear
safety glasses when working with compressed air. Never
use your hand to check for air leaks or to determine air
flow rates. (00061a)
7. Allow the filter element to either air dry or blow it dry from the inside with low pressure air.
8. Hold the filter element up to a strong light source. If light is uniformly visible through the
element, it is sufficiently clean. Replace the filter element if it is damaged or if the filter
media cannot be adequately cleaned.
NOTE:
Do not use air cleaner filter oil on HarleyDavidson paper/wire mesh air filter elements.
9. Remove the air cleaner cap. Place the air filter element in the bottom tray of the airbox.
Install the air cleaner cap over the air filter element and secure with the wing nut.
Install air filter before running engine. Failure to do so can
draw debris into the engine and could result in engine
damage. (00207a)
10. Position the airbox top over the air filter assembly and fasten the clips along each side and
the clip at the rear.
11. See Front Airbox Clip. The front clip under the snorkel is attached to the airbox top.
Fasten the clip over the lip on the airbox bottom.
12. See Airbox Cover: VRSC Models. Position the airbox cover with the locating pins in the
holes on the frame tabs.
13. Turn the bailhead fastener 1/4 turn clockwise to secure the airbox cover to the motorcycle.
14. On VRSCF model, install front side covers. See Front Side Covers: VRSCF Model.
15. Close seat.
1. Air filter element
2. Air cleaner cap
3. Wing nut
Air Cleaner Assembly: VRSC Models
Front Airbox Clip
Headlamp: VRSC Models
See Headlamp: VRSC Models. All VRSC headlamp assemblies use replaceable quartz
halogen bulb(s).
NOTE:
Refer to Bulb Chart: 2009 VRSC Models and see a service manual for more details.
When replacement is required, use only the specified
sealed beam unit or bulb, available from a HarleyDavidson
dealer. An improper wattage sealed beam or bulb, can
cause charging system problems. (00209a)
Never touch the quartz bulb. Fingerprints will etch the
glass and decrease bulb life. Grab the bulb with paper or a
clean, dry cloth. Failure to do so could result in bulb
damage. (00210a)
Handle bulb carefully and wear eye protection. Bulb
contains gas under pressure, which, if not handled
carefully, could cause serious eye injury. (00062b)
1. Headlamp bulbs
2. Position lamp harness (international only)
3. Position bulb (international only)
Headlamp: VRSC Models
Headlamp Alignment
The automaticon headlamp feature provides increased
visibility of the rider to other motorists. Be sure headlamp
is on at all times. Poor visibility of rider to other motorists
can result in death or serious injury. (00030b)
NOTE:
Vehicles with multiple beam headlamps that are individually aimed should be adjusted so both
lamps converge into one pattern.
1. Verify that front and rear tire inflation pressures are correct and that suspension is adjusted
to the weight of the principal rider. See Specifications.
2. Fill fuel tank or add ballast to equal the weight of the fuel needed.
NOTE:
See Headlamp Alignment: VRSC Models. To aid in properly placing the motorcycle, a
perpendicular line (1) can be drawn on the floor. For best results, choose an area with
minimum light.
3. See Headlamp Alignment: VRSC Models. Draw a vertical line (2) on the wall.
4. Position motorcycle so that front axle is 25 feet 7.6 meters from wall.
NOTE:
As the weight of the rider will compress the suspension slightly, have a person whose
weight is approximately the same as that of the principal rider sit on the motorcycle.
5. With the vehicle laden and upright, point the front wheel straight forward at wall and
measure the distance (4) from the floor to the center of the HIGH BEAM bulb.
6. Draw a horizontal line (5) through the vertical line on the wall that is 2.1 in. 53.3 mm lower
than the measured bulb centerline.
1. Perpendicular line
2. Vertical line
3. 7.6 meters (25 feet)
4. High beam bulb centerline
5. Horizontal line 53.3 mm (2.1 in.) lower than bulb centerline
Headlamp Alignment: VRSC Models
NOTE:
As the weight of the rider will compress the suspension slightly, have a person whose weight is
approximately the same as that of the principal rider sit on the motorcycle.
7. See Headlamp Alignment: VRSC Models. Verify headlamp alignment. Turn the ignition
switch to IGNITION and set the headlamp switch to HIGH beam.
a. The center of the hot spot (brightest area of light beam) should be centered where the
two lines intersect.
b. Adjust headlamp alignment if necessary.
Headlamp Adjustment
1. See Headlamp Alignment Fastener: VRSCAW/VRSCF Models (VRSCAW/VRSCF) or
Headlamp Alignment Fastener: VRSCDX Models (VRSCDX). Loosen fasteners slightly
so headlamp is still snug.
2. Move headlamp assembly to adjust vertical alignment.
3. Tighten fasteners. For VRSCAW and VRSCF models, tighten to 4066 inlbs (4.57.5 Nm).
For VRSCDX model, tighten to 2330 ftlbs (3141 Nm).
Headlamp Alignment Fastener:
VRSCAW/VRSCF Models
Headlamp Alignment Fastener: VRSCDX
Models
Tail Lamp and Turn Signals: VRSCF Model
The front turn signals and tail lamp (with integrated rear turn signals) are LED assemblies with no
replaceable bulbs. See a HarleyDavidson dealer or service manual for assembly replacement.
For proper alignment of front turn signals, see Mirrors: VRSCF Model.
Turn Signal Bulb Replacement: Bullet Style
1. See Lens Cap Notch. Insert a coin or the blade of a small screwdriver into the notch at the
bottom of the lens cap. Carefully twist until the lens cap pops out of the lamp housing.
2. Push in bulb and rotate counterclockwise. Pull bulb from socket.
3. Inspect condition of electrical contacts in socket. If necessary, clean with a small wire brush
and electrical contact cleaner.
4. Coat base of new bulb with ELECTRICAL CONTACT GREASE 9986190 .
5. Orient index pins on new bulb with pin guides inside bulb socket. Push bulb in and turn
clockwise to lock in place.
6. Snap lens cap back into the lamp holder. Rotate lens to position notch at bottom of lamp.
Be sure that all lights and switches operate properly
before operating motorcycle. Low visibility of rider can
7. Turn ignition on and test for proper turn signal operation.
NOTE:
If the turn signal or running lamp will not light after replacing a bulb, check the wiring, the ground
at the socket and/or the switch.
Lens Cap Notch
Tail Lamp Bulb Replacement: VRSCAW/VRSCDX Models
1. See Releasing Tail Lamp Retaining Clip: VRSCAW/VRSCDX. Insert a small
screwdriver into middle hole of license plate lamp cover. Push forward with screwdriver to
release tail lamp housing retaining clip.
2. Lift rear of tail lamp housing up and slide housing assembly away from fender.
3. See Tail Lamp Assembly: VRSCAW/VRSCDX Models. Turn bulb socket assembly
clockwise and pull outward from tail lamp housing.
4. Remove bulb by turning counterclockwise and pulling from bulb socket assembly.
5. Push new bulb into bulb socket assembly and turn clockwise.
6. Insert bulb socket assembly into tail lamp housing and turn counterclockwise to lock in
place.
7. Route all electrical connectors and wiring harnesses to either side of tail lamp opening in
fender, away from tail lamp bulb housing.
NOTE:
When installing tail lamp assembly, make sure tail lamp bulb is pointing toward rear of
vehicle.
8. Insert tabs on front of tail lamp housing under forward edge of fender opening.
9. Carefully push tail lamp assembly toward front of vehicle.
10. Engage retaining clip with rear edge of fender opening. Gently press down on tail lamp
assembly until clip locks in place.
NOTE:
Retaining clip must engage rear fender opening for tail lamp to remain locked into position in
rear fender.
Be sure that all lights and switches operate properly
before operating motorcycle. Low visibility of rider can
11. Turn ignition on and test for proper tail lamp operation.
Releasing Tail Lamp Retaining Clip:
VRSCAW/VRSCDX
1. Tail lamp bulb socket assembly
2. Retaining clip
3. Mounting tabs
Tail Lamp Assembly: VRSCAW/VRSCDX
Models
Alternator/Voltage Regulator
Charging Rate
The alternator output is controlled and changed to direct current by the voltage regulator.
The voltage regulator increases charging rate when battery is low or lamps are lit.
The voltage regulator decreases charging rate when battery charge is up.
It is possible to overload your motorcycle's charging
system by adding too many electrical accessories. If your
combined electrical accessories operating at any one time
consume more electrical current than your vehicle's
charging system can produce, the electrical consumption
can discharge the battery and cause vehicle electrical
system damage. See a HarleyDavidson dealer for advice
about the amount of current consumed by additional
electrical accessories, or for necessary wiring changes.
(00211b)
NOTES:
This unit requires no interval attention. If any electrical system trouble is experienced that
might be traceable to the alternator or voltage regulator, the motorcycle should be taken to a
HarleyDavidson dealer who has the necessary electrical testing equipment to give the
required attention.
For model specific information regarding the voltage regulator, refer to the appropriate
Service Manual or see a HarleyDavidson dealer.
Battery: General
Type
Your motorcycle uses a permanently sealed, maintenancefree, lead/calcium and sulfuric acid
battery. All batteries are shipped precharged and ready to be put into service. Do not attempt to
open the battery for any reason.
Antidotes for Battery Acid
CONTACT TREATMENT
External Flush with water.
Internal Drink large quantities of milk or water,
followed by milk of magnesia, vegetable oil
or beaten eggs. Get immediate medical
attention.
Eyes Flush with water. Get immediate medical
attention.
Batteries contain sulfuric acid, which could cause severe
burns to eyes and skin. Wear a protective face shield,
rubberized gloves and protective clothing when working
with batteries. KEEP BATTERIES AWAY FROM CHILDREN.
(00063a)
Explosive hydrogen gas, which escapes during charging,
could cause death or serious injury. Charge battery in a
wellventilated area. Keep open flames, electrical sparks
and smoking materials away from battery at all times.
KEEP BATTERIES AWAY FROM CHILDREN. (00065a)
Batteries, battery posts, terminals and related accessories
contain lead and lead compounds, and other chemicals
defects or other reproductive harm. Wash hands after
handling. (00019e)
Never remove warning label attached to top of battery.
Failure to read and understand all precautions contained
in warning, could result in death or serious injury. (00064a)
1. Contents are corrosive
2. Wear safety glasses
3. Contents are explosive
4. Keep flames away
5. Read instructions
6. Keep away from children
Battery Warning Label
Battery Warning Label
Voltmeter Test
Refer to Voltmeter Test. The voltmeter test provides a general indicator of battery condition.
Check the voltage of the battery to verify that it is in a 100 percent fully charged condition. If the
open circuit (disconnected) voltage reading is below 12.6V, charge the battery and then recheck
the voltage after the battery has set for one to two hours.
Voltmeter Test
READING IN VOLTS PERCENT OF CHARGE
12.7 100
12.6 75
12.3 50
12.0 25
11.8 0
Cleaning and Inspection
Battery top must be clean and dry. Dirt and electrolyte on top of the battery can cause battery to
selfdischarge.
1. Clean battery top.
2. Clean cable connectors and battery terminals using a wire brush or fine grit sandpaper to
remove any oxidation.
3. Inspect and clean the battery screws, clamps and cables. Check for breakage, loose
connections and corrosion.
4. Check the battery posts for melting or damage caused by overtightening.
5. Inspect the battery for discoloration, a raised top or a warped or distorted case. This might
indicate that the battery has been frozen, overheated or overcharged.
6. Inspect the battery case for cracks or leaks.
Charging
Never charge a battery without first reviewing the instructions for the charger being used. In
addition to the manufacturer's instructions, follow these general safety precautions.
Charge the battery if any of the following conditions exist:
Vehicle lamps appear dim.
Electric starter sounds weak.
Battery has not been used for an extended period of time.
Batteries contain sulfuric acid, which could cause severe
burns to eyes and skin. Wear a protective face shield,
rubberized gloves and protective clothing when working
with batteries. KEEP BATTERIES AWAY FROM CHILDREN.
(00063a)
1. Perform a voltmeter test to determine the state of charge. If battery needs to be charged,
proceed to the next step.
2. Place the battery on a level surface.
Unplug or turn OFF battery charger before connecting
charger cables to battery. Connecting cables with charger
ON can cause a spark and battery explosion, which could
Connect positive (+) battery cable first. If positive (+) cable
should contact ground with negative () cable connected,
the resulting sparks can cause a battery explosion, which
Disconnect negative () battery cable first. If positive (+)
cable should contact ground with negative () cable
connected, the resulting sparks can cause a battery
explosion, which could result in death or serious injury.
(00049a)
Do not reverse the charger connections described in the
following steps or the charging system of the motorcycle
could be damaged. (00214a)
NOTES:
The figures listed in the Amphour table assume that the battery is charging at room
temperature. If warmer than room temperature, use a slightly shorter charging time. If
colder, use a slightly longer charging time.
The use of constant current chargers to charge sealed maintenance free batteries is
not recommended. Any overcharge will cause dryout and premature battery failure. If
a constant current charger is the only type available, do not exceed the charge times
listed in 19 Amp Hour Battery Charging Rates/Times and do not continue
charging the battery if it gets hot. When charging, never exceed 15 volts.
3. Connect the red battery charger lead to positive (+) terminal of the battery.
4. Connect the black battery charger lead to negative () terminal of the battery.
NOTE:
If the battery is still in the vehicle, connect the negative lead to the chassis ground. Make
sure that the ignition and all electrical accessories are turned off.
5. Step away from the battery and turn on the charger.
Unplug or turn OFF battery charger before disconnecting
charger cables from battery. Disconnecting clamps with
charger ON can cause a spark and battery explosion,
6. After the battery is fully charged, turn OFF the charger and disconnect the black battery
charger lead to the negative () terminal of the battery.
7. Disconnect the red battery charger lead to the positive (+) terminal of the battery.
8. Mark the charging date on the battery.
19 Amp Hour Battery Charging Rates/Times
READING PERCENT 3 AMP 6 AMP 10 AMP 20 AMP
(VOLTS) OF CHARGE CHARGER CHARGER CHARGER CHARGER

12.7 100
12.6 75 1 hour 55 minutes 30 minutes 15 minutes
50 minutes
12.3 50 3 hours 1 hour 1 hour 30 minutes
40 minutes 50 minutes 5 minutes

12.0 25 5 hours 2 hours 1 hours 45 minutes

11.8 0 7 hours 3 hours 2 hours 1 hour
Storage
Turn engine over a few times to be sure there is no oil in
the crankcase and that all oil has been pumped back into
the oil tank. Stop engine and recheck oil level. Failure to
do so can result in engine damage. (00071a)
Do not allow battery to completely discharge. The
electrolyte in a discharged battery will freeze. The more
discharged a battery is, the more easily it can freeze and
crack the battery case. (00218a)
If the motorcycle will not be operated for several months, such as during the winter season,
remove the battery from the motorcycle and fully charge.
If the motorcycle is to be stored with the battery installed, it will be necessary to connect a battery
tender to maintain charge. See an authorized dealer for more information.
Selfdischarge is a normal condition and occurs continuously. The rate of selfdischarge depends
on the ambient temperature and the battery's state of charge.
Batteries discharge at a faster rate at higher ambient temperatures.
To reduce the selfdischarge rate, store battery in a cool (not freezing), dry place.
Charge the battery every month if stored at temperatures below 60° F 16° C .
Charge the battery more frequently if stored in a warm area above 60° F 16° C .
1. Capacity
2. Months of nonuse
3. Measured at 105° F (40° C)
4. Measured at 77° F (25° C)
Effective Rate of Temperature on Battery
Selfdischarging Rate
Battery: VRSC Models
Disconnection and Removal
Before you can inspect or disconnect the battery you must read the section containing information
about air cleaner removal.
1. Remove the main fuse. See Electrical Protection: VRSC Models.
2. Remove the air cleaner. See Air Cleaner: VRSC Models.
3. See Velocity Stacks. Disconnect rear breather hose (2).
4. Slide the oring (4) up each velocity stack (1) body to reveal the three retaining fasteners (5).
Unscrew the fasteners and lift off the velocity stacks.
5. Carefully lift up the airbox bottom tray. Two breather hoses are attached to the underside of
the airbox bottom tray. The front breather hose is a pressfit on a brass tube and will
disconnect. The rear breather hose was disconnected in a previous step. Slide rear breather
hose out through hole in rear of airbox tray.
Cover the throttle body bores with duct tape to prevent
objects from falling down the injector bores. Do NOT use
shop cloths or objects that could damage the throttle
plates. (00212d)
6. See Covering Injector Intakes. Cover injector intakes.
1. Velocity stacks
2. Rear breather hose
3. Airoil separator
4. Orings
5. Retaining fasteners (6)
Velocity Stacks
Covering Injector Intakes
Disconnect negative () battery cable first. If positive (+)
cable should contact ground with negative () cable
connected, the resulting sparks can cause a battery
explosion, which could result in death or serious injury.
(00049a)
7. See Battery Installed. Remove the battery negative cable from the negative () terminal of
the battery.
8. Remove the battery positive cable from the positive (+) terminal of the battery.
9. Stretch battery hold down strap and remove from tab to release tension on strap. Battery
hold down strap will become free from lower tab and can be completely removed.
10. Firmly pull battery out and slightly upward to remove battery from battery caddy.
1. Positive battery terminal bolt (located under boot)
2. Negative battery terminal bolt
3. Holddown strap
4. Tabs (strap anchor points, one located under battery tray)
5. Throttle cables
Battery Installed
Installation and Connection
1. Connect hold down strap to bottom of battery caddy.
2. See Battery Installed. Slide the fully charged battery into battery caddy, terminal side up,
negative () battery terminal toward the right side of the motorcycle.
NOTES:
Battery must sit flat on bottom of tray pad. Verify that battery does not sit on front edge of
pad.
3. See Battery Installed. Verify proper routing of throttle cable.
4. Stretch hold down strap over top of battery. Latch hold down strap to tab on top of battery.
Never route throttle cable over the battery. Fire due to
short circuit could occur and cause death or serious
injury. (00494c)
Connect the cables to the correct battery terminals. Failure
to do so could result in damage to the motorcycle
electrical system. (00215a)
Connect positive (+) battery cable first. If positive (+) cable
should contact ground with negative () cable connected,
the resulting sparks can cause a battery explosion, which
Do not allow positive (+) battery cable to contact ground
with negative () cable connected. Resulting sparks can
cause a battery explosion, which could result in death or
Do not overtighten bolts on battery terminals. Use
recommended torque values. Overtightening battery
terminal bolts could result in damage to battery terminals.
(00216a)
5. Insert a battery terminal bolt through the battery positive cable (+) (red), into the threaded
hole of the battery positive (+) terminal.
6. Tighten the bolt to 6070 inlbs (6.87.9 Nm).
7. Insert the other battery terminal bolt through the battery negative cable (black), into the
threaded hole of the battery negative () terminal.
8. Tighten the bolt to 6070 inlbs (6.87.9 Nm).
Keep battery clean and lightly coat terminals with
petroleum jelly to prevent corrosion. Failure to do so could
result in damage to battery terminals. (00217a)
9. Apply a light coat of petroleum jelly or corrosion retardant material to both battery terminals.
10. Remove the covering from the injector intakes.
11. See Air Cleaner Gasket and Alignment Pins. Inspect the gasket on the bottom of the
airbox tray. The gasket is located by the three alignment pins on the mating surface.
NOTE:
Replace the gasket if it is torn or damaged in any way.
12. Place the airbox tray over the injectors. Make sure the taller slanted lip of the tray faces the
front of the motorcycle. Slide the rectangular hole in the tray down over the threaded
mounting stud.
13. See Velocity Stacks. Insert rear breather hose through hole in rear of tray. Pull until hose
seals properly.
14. Align the front breather hose on the airbox tray with the brass tube and press the airbox tray
down firmly. Make sure the tray sits flush on top of the injectors.
NOTE:
In the next step, you will install the velocity stacks. Each velocity stack has an index mark.
Align the index mark on the velocity stack with the corresponding index mark on the airbox
tray.
15. See Air Cleaner Gasket and Alignment Pins. Align the index marks and install the
velocity stacks, the longest stack toward the front of the motorcycle. Start all fasteners by
hand first, making sure none are crossthreaded. Tighten the three fasteners on each
velocity stack to 53 inlbs (6 Nm).
16. Slide the oring down each velocity stack until it contacts the three fasteners. Slide the
breather hose onto the rear breather hose fitting.
17. Reinstall the air filter element, air cleaner cap, wing nut, airbox top, electrical connector on
airbox, and airbox cover. Lower the seat down.
18. Install the main fuse. See Electrical Protection: VRSC Models.
Air Cleaner Gasket and Alignment Pins
1. Velocity stack index mark
2. Airbox tray index mark
Velocity Stack and Airbox Tray Index
Marks
Jump Starting
HarleyDavidson does not recommend jumpstarting a motorcycle. However, there may be
circumstances when it is necessary to do so. Therefore, we suggest jumpstarting be performed
as follows:
Be sure jumper cables touch only appropriate battery
terminals or ground. Allowing jumper cables to touch each
other can result in sparks and a battery explosion, which
HarleyDavidson motorcycles have a 12 Volt battery. Be
sure the booster vehicle has a 12 Volt system. Failure to
do so could result in vehicle damage. (00220a)
NOTE:
This procedure presumes the BOOSTER battery is in another vehicle.
1. Turn off all unnecessary lamps and accessories.
Positive Cable
2. See Jump Start Cable Connections. Connect one end of a jumper cable to the
DISCHARGED battery positive (+) terminal (1).
3. Connect the other end of the same cable to the BOOSTER battery positive (+) terminal (2).
Negative Cable
Do not connect negative () cable to or near the discharged
battery negative () terminal. Doing so could cause a spark
and explosion, which could result in death or serious
injury. (00073a)
4. Connect one end of a jumper cable to the BOOSTER battery negative () terminal (3).
Do not connect the negative () cable to painted or chrome
parts. Doing so could result in discoloration at the
attachment point. (00221a)
5. Connect other end of the same cable (4) to a safe ground, (away from the DISCHARGED
battery).
6. Start motorcycle.
7. Disconnect cables in reverse order of steps 2, 3, 4, 5. That is: steps 5, 4, 3, 2.
1. Discharged battery positive (+) terminal
2. Booster battery positive (+) terminal
3. Booster battery negative () terminal
4. Ground
Jump Start Cable Connections
Electrical Protection: VRSC Models
VRSC models have a rear fuse block under the seat and a front fuse block behind the steering
head under the right side cover.
For electrical problems, it is best to see a HarleyDavidson dealer who has the necessary parts
and equipment to perform electrical services.
Fuses do not reset. A blown fuse must be replaced with a fuse of the same rating.
NOTE:
Use only automotive type ATO fuses as replacements.
Front Fuse Block
1. Make sure the ignition is turned OFF.
2. Remove the front right side cover.
a. For VRSCF model, see Front Side Covers: VRSCF Model.
b. For other models, remove the fastener from the front right side cover and carefully lift
the side cover off the mounting tabs.
3. See Front Fuse Block and Main Fuse: VRSC Models. The front fuse block is mounted
on the top right side of the battery box. Pull the tabs out from the sides of the fuse block
cover. Remove cover.
4. See Front Fuse Block: VRSC Models. Remove the suspect fuse and inspect the element.
Replace the fuse if the element is burned or separated.
5. Install the fuse block cover. Carefully press the cover until tabs snap into place.
6. Install the right front side cover.
b. For other models, install front side cover on the mounting tabs. Line up the hole on the
cover with the threaded hole in the frame tab and install the fastener. Tighten the
fastener to 97.2150 inlbs (1117 Nm).
1. Front fuse block (cover removed)
2. Main fuse
Front Fuse Block and Main Fuse: VRSC Models
1. Spare (15 amp.)
2. Start relay
3. ABS fuse (ABSequipped models only, 30 amp.)
4. Battery (15 amp.)
5. Ignition (15 amp.)
6. Fan relay
Front Fuse Block: VRSC Models
Rear Fuse Block
1. Make sure the ignition is turned OFF.
2. Open the seat.
3. See Rear Fuse Block Location: VRSC Models. The rear fuse block is located on frame
crossmember behind fuel filler cap. Slide the fuse block to the left side of vehicle to remove
from mount.
4. See Rear Fuse Block: VRSC Models. Remove the suspect fuse and inspect the element.
Replace the fuse if the element is burned or separated.
5. Slide fuse block onto the mount. Close the seat.
Rear Fuse Block Location: VRSC Models
1. Spare (15 amp.)
2. Security (15 amp.)
3. Accessory (15 amp.)
4. P&A Ignition (2 amp. max)
5. Lights (15 amp.)
6. ECM power (15 amp.)
7. Fuel pump (15 amp.)
8. System relay
Rear Fuse Block: VRSC Models
Main Fuse
All VRSC models have a main fuse to protect the motorcycle wiring. This 40amp main fuse
provides main battery power to the motorcycle. It is located in a rubbercoated fuse holder behind
the motorcycle's right side cover.
1. Remove the front right side cover.
b. For other models, remove the fastener from the front right side cover and carefully lift
the side cover off the mounting tabs.
2. Grasp the fuse holder in one hand, the plastic body of the main fuse in the other, and pull
the main fuse straight out of the fuse holder.
3. Insert the prongs of the new main fuse in the fuse holder slots. Push the main fuse firmly
down into the fuse holder.
4. Install the right front side cover.
b. For other models, install front side cover on the mounting tabs. Line up the hole on the
cover with the threaded hole in the frame tab and install the fastener. Tighten the
fastener to 97.2150 inlbs (1117 Nm).
Inserting Main Fuse (typical)
Seat: VRSC Models
Opening
Seat is hinged on the left side. Grasp lower edge of right side and lift.
NOTE:
See Seat Lanyard: VRSC Models. The lanyard will hold the seat in position on the motorcycle
frame.
Closing
Rotate seat down to close seat.
NOTE:
Refer to the VRSC Service Manual for information pertaining to seat installation and removal.
Seat Lanyard: VRSC Models
Motorcycle Storage: VRSC Models
Placing Motorcycle in Storage
Proper storage is important for the troublefree operation
of your motorcycle. See your Owner's Manual for storage
recommendations or see a HarleyDavidson dealer.
Improper storage procedures can lead to equipment
damage. (00046a)
If the motorcycle will not be operated for several months, such as during the winter season, there
are several tasks which should be performed. These steps will protect parts against corrosion,
preserve the battery and prevent the buildup of gum and varnish in the fuel system.
NOTE:
Make a list of everything you do and fasten it to a handgrip. When you take the motorcycle out of
storage, this list will be your reference/checklist to get your motorcycle in operating condition.
1. Fill fuel tank and add a gasoline stabilizer. Use one of the commercially available gasoline
stabilizers and follow the manufacturer's instructions.
2. Warm motorcycle to operating temperature. Change oil and turn engine over to circulate the
new oil.
3. Adjust the belt.
4. Check tire inflation. Adjust to proper inflation pressure.
5. Prepare battery for winter storage. See Battery: General.
6. If the motorcycle is to be stored with security system armed, it will be necessary to connect
a Battery Tender to maintain battery charge. If security system will not be armed and a
Battery Tender is not available, remove the Maxifuse.
7. Check and fill the cooling system.
8. To protect the vehicle's body panels, engine, chassis and wheels from corrosion, follow the
cosmetic care procedures described in the Accessory Maintenance section of this owner's
manual prior to storage.
9. If motorcycle is to be covered, use a material such as light canvas that will breathe. Plastic
materials that do not breathe promote the formation of condensation.
Removing Motorcycle From Storage
The clutch failing to disengage can cause loss of control,
which could result in death or serious injury. Prior to
starting after extended periods of storage, place
transmission in gear and push vehicle back and forth
several times to assure proper clutch disengagement.
(00075a)
1. See Battery: General for proper battery care. Charge and install the battery.
2. Remove and inspect the spark plugs. Replace if necessary.
3. Clean the air cleaner element.
4. Start the engine and run until it reaches normal operating temperature. Turn off engine.
5. Check the oil.
6. Check the clutch fluid level.
7. Check controls to be sure they are operating properly. Operate the front and rear brakes,
throttle, clutch and shifter.
8. Check steering for smoothness by turning the handlebars through the full operating range.
Coolant mixture contains toxic chemicals, which may be
fatal if swallowed. If swallowed, do not induce vomiting;
call a physician immediately. Use in a well ventilated area.
Irritation to skin or eyes can occur from vapors or direct
contact. In case of skin or eye contact, flush thoroughly
with water and go to hospital, if necessary. Dispose of
used coolant according to federal, state and local
regulations. (00092a)
9. Check the radiator connections and coolant level.
10. Check tire pressure. Incorrect pressure will result in poor riding characteristics and can
affect handling and stability.
11. Check all electrical equipment and switches including the stop lamp, turn signals and horn
for proper operation.
12. Check for any fuel, oil, coolant or brake fluid leaks.
Turn engine over a few times to be sure there is no oil in
the crankcase and that all oil has been pumped back into
the oil tank. Stop engine and recheck oil level. Failure to
do so can result in engine damage. (00071a)
Accessories Maintenance
Accessories Maintenance
General Maintenance
Maintain chrome and aluminum regularly to check that they retain their original shine and luster.
Take care to keep your new HarleyDavidson motorcycle cleaned and waxed as often as possible
to inhibit rust and corrosion.
Denim Finish
General
If your vehicle has denim (flat or matte) finish please read below.
The Denim finish has qualities which differ from high gloss finishes on all other Harley
Davidson motorcycles. Like denim fabric, Denim paint will burnish or mar with age and use,
thus adding character and personality to the finish of the motorcycle.
If scratched, the color coat of paint does nick/scuff and these marks can not be rubbed out.
If polished, the finish will become less matte and more glossy over time.
How to Clean
1. For heavier deposits:
a. Use grease cutting dishwashing detergent and a clean HD washmitt. (Dilute the
detergent per the instruction provided by its manufacturer.)
b. Rinse thoroughly with clean water.
2. For light deposits, use glass cleaner (ammonia base) and HD Soft Cloth. This helps remove
finger prints and light soil.
3. For final detailing use HD Gloss with HD Soft Cloth.
Cleaning Your VRod
Improper cleaning, or the use of nonrecommended care
products, or lack of proper maintenance of your VRSC will
void your cosmetic warranty coverage. (00226a)
Observe warnings on labels of cleaning compounds.
Failure to follow warnings could result in death or serious
injury. (00076a)
To aid you in keeping your motorcycle clean, see a HarleyDavidson dealer for cleaning and
polishing products. As a general guideline, it is recommended that you use the following products
for the purposes listed in Recommended Cleaning Care Products.
Recommended Cleaning Care Products
PRODUCT PART FRAME BODY WHEELS DENIM CHROME/
NUMBER PANELS FINISH SATIN
STAINLESS
HD Sunwash 9465998 Yes Yes Yes No Yes
HD Bug Remover 9465798 Yes Yes Yes No Yes
HarleyGloss 9462798 Yes Yes Yes Yes Yes
Harley Spray Cleaner and Polish 9981799 Yes Yes Yes No Yes
Wheel and Tire Cleaner 9465898 No No Yes No No
S100 Total Cycle Cleaner 99760 Yes Yes Yes No Yes
85T
(complete rinse required)
Grease cutting dishwasher N/A No No No Yes No
detergent. Dilute per
manufacturer's instructions.
Ammonia base glass cleaner N/A No No No Yes No
1. Use HD SUNWASH (Part No. 9465998) first, for general cleaning and washing of all
surface finishes. Sunwash has a formulated sheeting action that prevents hard water spots
and rinses clean even on hot days in the sun.
Use of pressure washers to clean radiator and oil cooler
can damage cooling fins and reduce airflow. Reduced
airflow can lead to overheating, resulting in engine
damage and could void your engine warranty. (00056a)
Do not use pressure washers to clean wheel bearings,
sprocket bearings, steering head bearings and swingarm
pivot bearings. Doing so can result in equipment damage.
(00489b)
2. Next, use HD BUG REMOVER (Part No. 9465798) to remove bugs from all surface
finishes. Bug Remover will not damage metal, plastic or painted surfaces.
3. Finally, use HARLEY GLOSS (Part No. 9462798) as an allpurpose surface protectant that
provides UV protection and a gloss finish. Harley Gloss contains no waxes, silicones, oils or
hydrocarbon solvents.
4. Use HARLEY SPRAY CLEANER AND POLISH (Part No. 9981799) for quick touchups. It's
an allpurpose aerosol cleaner and quick detailer, great for all metal surfaces. This product
also reduces static attraction to dust.
5. Use WHEEL AND TIRE CLEANER (Part No. 9465898) to clean and degrease wheels and
tires. Do not use on frame or anodized parts.
6. On VRSCF model, keep the tail lamp assembly clean by using NOVUS NO. 1
CLEANER/PROTECTANT (Part No. 9983794T) and NOVUS NO. 2 SCRATCH REMOVER
(Part No. 9983694T) products. Apply Novus products with a clean HD Softcloth.
We recommend use of the products listed above. If you
wish to use nonrecommended cleaning products, test
them only in an inconspicuous area on the vehicle's
surface first. Do NOT use abrasive or etching cleaners on
anodized surfaces! Doing so can result in damage to the
surface. (00227a)
Use ONLY Harley Spray Cleaner and Polish, or Harley
Gloss on painted surfaces. Use of other cleaners or
polishes can damage painted surfaces. (00228a)
NOTE:
See a HarleyDavidson dealer for repair, restoration, or customization of anodized or painted
surfaces.
Observe warnings on labels of cleaning compounds.
Failure to follow warnings could result in death or serious
injury. (00076a)
Cooling fans operate automatically, even when the ignition
switch is off. Keep hands away from fan blades. Contact
with a rotating fan blade can result in minor or moderate
injury. (00093a)
Clean the inlet surface of the radiator regularly. Leaves
and other debris can collect on the radiator surface and
degrade radiator performance which could lead to engine
overheating and engine damage. (00197c)
Leather Care
NOTE:
Many HarleyDavidson accessories and seats are either made of leather or have leather inserts.
Natural materials age differently and require different care than manmade materials. Seat covers
and panels made of leather will gain "character", such as wrinkles, with age. Leather is porous
and organic and each leather product will settle into its own distinct form with use. Your leather
product will mature into its own custom shape and style from the sun, rain and the miles. This
maturing is natural and will enhance the custom quality of your HarleyDavidson motorcycle.
Leather must be periodically cleaned and treated to maintain its appearance and extend its life.
Clean and treat leather once a season or more frequently under adverse conditions.
Do not use bleach or detergents containing bleach on
saddlebags, seats, tank panels or painted surfaces. Doing
so can result in equipment damage. (00229a)
Do not use ordinary soap to clean leather or fur. It could dry or remove the oils from the
leather.
Use ONLY a good quality saddle soap to clean leather. Be sure you rinse saddle soap off
thoroughly before treating leather.
Never try to dry leather quickly, using artificial means. Always let leather dry naturally, at
room temperature.
1. Vacuum or blow dust off.
2. Thoroughly clean leather with a good quality saddle soap, following manufacturer's
directions. Rinse thoroughly with clean sponge or cloth and water. Allow leather to dry.
3. Once leather is dry, treat with a good quality leather treatment, such as LEATHERCARE
(Part No. 9826191).
4. Always allow leather to dry completely before using.
Wheel Care: VRSC Models
The vehicle's wheels are cast aluminum. Damage from harsh chemicals, acid based wheel
cleaners, brake dust and lack of maintenance can occur. Regular washing and the use of a
corrosion protectant will help to maintain their original appearance. HarleyDavidson Wheel & Tire
Cleaner 9465898 is recommended for cleaning wheels and tires. Then use Harley Gloss 94627
98 to protect the aluminum wheel surfaces.
NOTES:
Follow recommended service procedures for your tire if applicable.
It is imperative that the wheels are cared for weekly, according to the instructions above, to
guard against pitting and corrosion.
Corrosion of these components is not considered to be a defect in materials or
workmanship.
See a HarleyDavidson dealer for cleaning and polishing products.
Windshields
Polycarbonate windscreens/windshields require proper
attention and care to maintain. Failure to maintain
polycarbonate properly can result in damage to the
windscreen/windshield. (00483d)
Do not clean in hot sun or high temperature.
Powdered, abrasive or alkaline cleanser will damage the windscreen/windshield.
Do not use harsh chemicals including rain sheeting
products on HarleyDavidson windshields. They can cause
dulling or hazing. If you want to use a windshield
protectant on your windshield, try Harley Glaze Polish and
Sealant (00231a)
Do not use benzine, paint thinner, gasoline or any other
type of harsh cleaner on the windshield. Doing so will
damage the windshield surface. (00232a)
NOTES:
To remove minor surface scratches use NOVUS® No. 2 SCRATCH REMOVER (Part No.
9983694T).
Covering the windshield with a clean, wet cloth for approximately 1520 minutes before
washing will make dried bug removal easier.
1. Use mild soap and warm water to wash the windshield.
2. Wipe dry with a soft, clean towel.
NOTE:
To treat your Lexan windshield with water repellent use WINDSHIELD WATER REPELLENT
TREATMENT (Part No. 9984102).
Troubleshooting
Troubleshooting: General
The troubleshooting section of the Owner's Manual is a
guide to diagnose problems. Read the service manual
before performing any work. Improper repair and/or
maintenance could result in death or serious injury.
(00080a)
The following checklist of possible operating troubles and their probable causes will be helpful in
keeping your motorcycle in good operating condition. More than one of these conditions may be
causing trouble and should be carefully checked.
Engine: VRSC Models
Starter Does Not Operate or Does Not Turn Engine Over
1. Engine run switch in OFF position.
2. Ignition switch not ON.
3. Discharged battery or loose or corroded connections (solenoid chatters).
4. Clutch lever not squeezed against handlebar or transmission not in neutral.
5. Jiffy stand not in retracted position (required for international models only).
6. Blown fuse.
Engine Turns Over But Does Not Start
1. Fuel tank empty.
2. Fuel vacuum line disconnected.
3. Fuel valve or filter clogged.
4. Discharged battery or loose or broken battery terminal connections.
5. Fouled spark plugs.
6. Spark plug coil connections loose or in bad condition and shorting.
7. Loose or corroded wire or cable connection(s) at coil or battery.
8. Fuel pump inoperative.
9. Blown fuse.
Starts Hard
1. Spark plugs in bad condition, have improper gap, or are partially fouled.
2. Battery nearly discharged.
3. Loose wire or cable connection(s) at one of the battery terminals or at coil.
4. Engine oil too heavy (winter operation).
5. Fuel tank vent plugged or fuel line closed off, restricting fuel flow.
6. Water or dirt in fuel system.
7. Fuel pump inoperative.
Starts But Runs Irregularly or Misses
1. Spark plugs in bad condition or partially fouled.
2. Spark plug gap too close or too wide.
3. Battery nearly discharged.
4. Damaged wire or loose connection at battery terminals or coils.
5. Intermittent short circuit due to damaged wire insulation.
6. Water or dirt in fuel system, filter or carburetor.
7. Fuel vent system plugged. See dealer.
8. One or more injectors fouled.
A Spark Plug Fouls Repeatedly
1. Incorrect spark plug.
Preignition or Detonation (Knocks or Pings)
1. Incorrect fuel.
2. Incorrect spark plug for the kind of service.
Overheats
1. Insufficient oil supply or oil not circulating.
2. Heavy carbon deposit from lugging engine. See dealer.
Excessive Vibration
1. Rear fork pivot shaft nuts loose. See dealer.
2. Front engine mounting bolts loose. See dealer.
3. Broken frame. See dealer.
4. Belt badly worn.
5. Wheels and/or tires damaged. See dealer.
6. Vehicle not properly aligned. See dealer.
Cooling System
Overheats
1. Air flow through the radiator is obstructed.
2. The radiator is internally plugged.
3. Insufficient coolant.
4. Cooling fans not operating.
5. Thermostat stuck closed.
Electrical System
Alternator Does Not Charge
1. Module not grounded. See dealer.
2. Engine ground wire loose or broken. See dealer.
3. Loose or broken wires in charging circuit. See dealer.
Alternator Charge Rate is Below Normal
1. Weak battery.
2. Excessive use of addon accessories.
3. Loose or corroded connections.
4. Extensive periods of idling or low speed riding.
Transmission: VRSC Models
Transmission Shifts Hard
1. Bent shifter rod. See dealer.
2. Transmission shifting mechanism needs adjustment. See dealer.
Transmission Jumps Out of Gear
1. Shifter rod improperly adjusted. See dealer.
2. Shifter forks (inside transmission) improperly adjusted. See dealer.
3. Worn shifter dogs in transmission. See dealer.
Clutch Slips
1. Clutch controls improperly adjusted. See dealer.
2. Worn friction discs. See dealer.
3. Insufficient clutch spring tension. See dealer.
Clutch Drags or Does Not Release
1. Clutch controls improperly adjusted. See dealer.
2. Insufficient clutch spring tension. See dealer.
3. Clutch discs warped. See dealer.
Clutch Chatters
1. Friction discs or steel discs worn or warped. See dealer.
Brakes
ABS System Behavior
1. ABS lamp does not shut off above 3 mph 5 km/h . See dealer.
2. Other ABS symptoms. Refer to ABS Symptoms and Conditions.
Brakes Do Not Hold Normally
1. Master cylinder low on fluid. See dealer.
2. Brake line contains air bubbles. See dealer.
3. Master or wheel cylinder piston worn. See dealer.
4. Brake pads contaminated with grease or oil. See dealer.
5. Brake pads badly worn. See dealer.
6. Brake disc badly worn or warped. See dealer.
7. Brake fades because of heat build up. Excessive braking or brake pads dragging. See
dealer.
8. Brake drags. Insufficient hand lever free play. See dealer.
Warranties and Responsibilities
Warranties and Responsibilities
Warranty and Maintenance
This Owner's Manual contains your new motorcycle warranty.
It is the owner's responsibility to follow the scheduled mileage intervals as specified; all of the
specified maintenance services must be performed to keep your warranty valid.
1. Make an appointment with a HarleyDavidson dealer for inspection and service just before
you have ridden 1000 miles 1600 kilometers .
2. Bring this Owner's Manual with you when you visit your dealer to have your motorcycle
inspected and serviced.
3. Have the dealer technician sign at the proper mileage interval. The records should be
retained by the owner as proof of proper maintenance.
4. Keep receipts covering any parts, service or maintenance performed. These records should
be transferred to each subsequent owner.
injury. (00001a)
HarleyDavidson dealerships are independently owned and operated and may sell parts and
accessories that are not manufactured or approved by HarleyDavidson. Therefore, you should
understand that we are not and cannot be responsible for the quality, suitability, or safety of any
nonHarleyDavidson part, accessory or design modification, including labor, which may be sold
and/or installed by our dealers.
Keeping It All HarleyDavidson
1. Keep your HarleyDavidson completely HarleyDavidson.
2. Insist that your dealer uses only Genuine replacement parts to keep your HarleyDavidson
motorcycle and its warranty intact.
Exacting design and stringent testing ensure performance and warranty coverage. Again, insist on
Genuine parts for your genuine HarleyDavidson motorcycle.
NOTE:
Installing offroad or competition parts to enhance performance may void all or part of your new
motorcycle warranty. See the HarleyDavidson Limited Warranty in this manual or a Harley
Davidson dealer for details.
It is possible to overload your motorcycle's charging
system by adding too many electrical accessories. If your
combined electrical accessories operating at any one time
consume more electrical current than your vehicle's
charging system can produce, the electrical consumption
can discharge the battery and cause vehicle electrical
system damage. See a HarleyDavidson dealer for advice
about the amount of current consumed by additional
electrical accessories, or for necessary wiring changes.
(00211b)
Important Moving Information
If you move from your present address, or sell your motorcycle, please fill out and mail the post
card at the back of this manual. This is necessary in the event that the Company needs to contact
the owner concerning information that could affect the safe operation of this motorcycle.
California Evaporative Emission Controls: 2009 Models
All new model year 2009 HarleyDavidson motorcycles sold in the State of California are
equipped with an evaporative emission control system. This system is designed to meet the
CARB regulations in effect at the time of manufacture.
The system requires a small amount of maintenance. Periodic inspection is required to make sure
hoses are properly routed, not kinked or blocked and that all fittings are secure. Mounting
hardware should also be checked periodically for tightness.
EPA Noise Regulations in the United States
EPA noise regulations require that the following statements be included in the Owner's Manual.
TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED: Federal law prohibits the
following acts or the causing thereof: (1) The removal or rendering inoperative by any person
other than for purposes of maintenance, repair, or replacement of any device or element of design
incorporated into any new vehicle for the purpose of noise control prior to its sale or delivery to the
ultimate purchaser or while it is in use, or (2) the use of the vehicle after such device or element of
design has been removed or rendered inoperative by any person.
AMONG THOSE ACTS PRESUMED TO CONSTITUTE TAMPERING ARE THE ACTS LISTED
BELOW.
1. Replacing the muffler(s) and/or the entire exhaust system with parts not certified to be noise
legal for street use.
2. Removing or modifying the muffler internal baffles in any way.
3. Replacing the air intake/cleaner assembly with one not certified to be noise legal for street
use.
4. Modifying the air intake/cleaner assembly in such a way as to make the vehicle no longer
noise legal for street use.
HarleyDavidson recommends that any and all noise related maintenance be done by an
authorized HarleyDavidson dealer using genuine HarleyDavidson parts.
Warranty/Service Information
Any authorized HarleyDavidson dealer is responsible for providing the warranty repair work on
your motorcycle. If you have any questions regarding warranty obligations contact your selling
dealer.
For normal service work or warranty work under the above conditions, you may obtain the name
and location of your nearest U.S. HarleyDavidson dealer by calling 18004909635 (toll free), in
any state except Alaska and Hawaii.
NOTE:
The number shown above is accessible only with a touchtone phone in the United States.
Reporting Safety Defects in United States
Safety defects must be reported to the National Highway Traffic Safety Administration (NHTSA)
and HarleyDavidson.
NHTSA Statement
If you believe that your vehicle has a defect which could cause a crash or could cause injury or
death, you should immediately inform the National Highway Traffic Safety Administration
(NHTSA) in addition to notifying HarleyDavidson.
If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety
defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA
cannot become involved in individual problems between you, your dealer, or HarleyDavidson.
To contact NHTSA, refer to NHTSA Contacts.
NHTSA Contacts
ITEM DATA
Phone Call the Auto Safety Hot Line tollfree at 1888
DASH2DOT
Mail U.S. Department of Transportation, National
Highway Traffic Safety Administration, Office of
Defects Investigation, NVS210, 400 7th Street
S.W., Washington, D.C. 20590
Web www.nhtsa.dot.gov
site
You can also obtain other information about motor vehicle safety from the hot line.
Owner Transfer Identification Form
When purchasing a preowned HarleyDavidson or Buell, we encourage you to submit an Owner
Transfer Notification Form. It is critical that new owner information is communicated to Harley
Davidson. New owner information is required to be on file with HarleyDavidson to transfer an
Extended Service Plan Contract. HarleyDavidson is also required by the National Traffic and
Motor Vehicle Safety Act to notify all owners in the event of a recall. The form may be obtained at
any HarleyDavidson dealer.
Required Documentation for Imported Motorcycles
If a HarleyDavidson is imported into the United States, additional documentation is required to be
eligible for the United States Manufacturer's Limited Warranty. A HarleyDavidson dealer can
provide a form explaining the requirements.
Limited Motorcycle Warranty
2009 HARLEYDAVIDSON MOTORCYCLE LIMITED WARRANTY
24 Months/Unlimited Miles
HarleyDavidson warrants for any new 2009 HarleyDavidson motorcycle/sidecar that an
authorized HarleyDavidson dealer will repair or replace without charge any parts found under
normal use to be defective in factory materials or workmanship. Such repair and replacement will
be HarleyDavidson's sole obligation and the customer's sole remedy under this warranty.
THERE IS NO OTHER EXPRESS WARRANTY (OTHER THAN THE SEPARATE EMISSIONS
AND NOISE WARRANTIES) ON THE MOTORCYCLE. ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE IS LIMITED TO THE
DURATION OF THIS WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation
may not apply to you.
TO THE FULLEST EXTENT ALLOWED BY LAW, HARLEYDAVIDSON AND ITS DEALERS
SHALL NOT BE LIABLE FOR LOSS OF USE, INCONVENIENCE, LOST TIME, COMMERCIAL
LOSS OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you. This warranty gives you specific legal rights, and you may have
other rights which vary from state to state.
The following terms and conditions apply to this warranty:
Duration
1. The duration of this limited warranty is twenty four months, starting from the earlier of (a) the
date of initial retail purchase and delivery from an authorized HarleyDavidson dealer, or (b)
the third anniversary of the last day of the model year of the motorcycle/sidecar. Your dealer
will submit an electronic Sales and Warranty Registration form to initiate your warranty.
2. Any unexpired portion of this limited warranty will be transferred to subsequent owners,
upon the resale of the motorcycle/sidecar during the warranty period.
Owner's Obligations
To obtain warranty service, return your motorcycle/sidecar at your expense within the warranty
period to an authorized dealer. Our dealer should be able to provide warranty service during
normal business hours and as soon as possible, depending upon the workload of the dealer's
service department and the availability of necessary parts.
HarleyDavidson Motor Company, P.O. Box 653, Milwaukee, Wisconsin 53201, U.S.A.
Exclusions
This warranty will not apply to any motorcycle/sidecar as follows:
1. Which has not been operated or maintained as specified in the Owner's Manual.
2. Which has been abused, misused, improperly stored, used "off the highway," or used for
racing or competition of any kind.
3. Which is not manufactured to comply with the laws of the market in which it is registered.
4. Installing offroad or competition parts to enhance performance may void all or part of your
new motorcycle warranty. See a HarleyDavidson dealer for details.
5. Acts of God, war, riot, insurrection, natural disasters, including, but not limited to, nuclear
contamination, lightning, dust storms, hail storms, ice storms, earthquakes, floods, or for
other circumstances out of HarleyDavidson's control.
Other Limitations
This warranty does not cover:
1. Parts and labor for normal maintenance as recommended in the Owner's Manual, or the
replacement of parts due to normal wear and tear including such items as the following:
tires, lubrication, oil and filter change, fuel system cleaning, battery maintenance, engine
tuneup, spark plugs, brake, clutch and chain/belt adjustment (including chain replacement).
2. Cosmetic concerns that arise as a result of owner abuse, lack of proper maintenance or
environmental conditions (except concerns that result from defects in material or
workmanship, which are covered by this warranty for the duration of the warranty period).
3. Any cosmetic condition existing at the time of retail delivery that has not been documented
by the selling dealer prior to retail delivery.
4. Defects or damage to the motorcycle caused by alterations outside of HarleyDavidson
factory specifications.
Important: Read Carefully
1. Our dealers are independently owned and operated and may sell other products. Because
of this, HARLEYDAVIDSON IS NOT RESPONSIBLE FOR THE SAFETY, QUALITY, OR
SUITABILITY OF ANY NONHARLEYDAVIDSON PART, ACCESSORY OR DESIGN
MODIFICATION INCLUDING LABOR WHICH MAY BE SOLD AND/OR INSTALLED BY
OUR DEALERS.
2. This warranty is a contract between you and the manufacturer. It is separate and apart from
any warranty you may receive or purchase from the dealer. The dealer is not authorized to
alter, modify, or in any way change the terms and conditions of this warranty.
3. Any warranty work or parts replacement authorized by the manufacturer will not preclude
the manufacturer from later relying on any exclusion where applicable.
Limited Noise Warranty
2009 HARLEYDAVIDSON MOTORCYCLE NOISE CONTROL SYSTEM LIMITED
WARRANTY
The following warranty applies to the noise control system, is in addition to the MOTORCYCLE
LIMITED WARRANTY and EMISSION CONTROL SYSTEM LIMITED WARRANTY, and applies
only to motorcycles sold in the U.S.
HarleyDavidson Motor Company warrants that this vehicle is designed and built so as to conform
at the time of sale with applicable regulations of the U.S. Environmental Protection Agency (as
tested following F76 DriveBy test procedure) and that it is free from defects in materials and
workmanship which would cause this motorcycle not to meet U.S. Environmental Protection
Agency Standards within 1 year or 3,730 miles (6,000 kilometers) whichever expires first. Any
unexpired portion of this limited warranty will be transferred to subsequent owners, upon the
resale of the motorcycle during the warranty period.
THERE IS NO OTHER EXPRESS WARRANTY (OTHER THAN THE SEPARATE
MOTORCYCLE AND EMISSIONS WARRANTIES) ON THE MOTORCYCLE. ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE IS LIMITED
TO THE DURATION OF THIS WARRANTY.
The warranty period shall begin on the date the motorcycle is delivered to the first retail purchaser
or, if the motorcycle is placed in service as a demonstrator or company vehicle prior to sale at
retail, on the date it is first placed in service.
THE FOLLOWING ITEMS ARE NOT COVERED BY THE NOISE CONTROL SYSTEM
WARRANTY
1. Failures which arise as a result of misuse, alterations, or accident as specified in the
Owner's Manual.
2. Replacing, removing, or modifying any portion of the NOISE CONTROL SYSTEM
(consisting of the exhaust system and air intake/cleaner assembly) with parts not certified to
be legal for street use.
3. Any motorcycle on which the odometer mileage has been changed so that the mileage
cannot be determined.
4. TO THE FULLEST EXTENT ALLOWED BY LAW, HARLEYDAVIDSON AND ITS
DEALERS SHALL NOT BE LIABLE FOR LOSS OF USE, INCONVENIENCE, LOST TIME,
COMMERCIAL LOSS OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you.
Other Rights
This warranty gives you specific legal rights, and you may have other rights which vary from state
to state.
Recommendations for Required Maintenance
It is recommended that any noise system maintenance be performed by an authorized Harley
Davidson dealer using genuine HarleyDavidson replacement parts. The maintenance,
replacement or repair of the noise control system may be performed by any other qualified service
outlet or individual. Nongenuine parts may be used only if such parts are certified to comply with
U.S. Environmental Protection Agency Standards.
Limited Emission Warranty
2009 HARLEYDAVIDSON EMISSION CONTROL SYSTEM LIMITED WARRANTY
The following warranty applies to the emission control system, is in addition to the LIMITED
MOTORCYCLE WARRANTY and NOISE CONTROL SYSTEM LIMITED WARRANTY, and
applies only to motorcycles sold in the U.S.
HarleyDavidson Motor Company warrants that this vehicle is designed and built so as to conform
at the time of sale with applicable regulations of the U.S. Federal Environmental Protection
Agency, and that it is free from defects in materials and workmanship which would cause this
motorcycle not to meet U.S. Environmental Protection Agency Standards within 5 years or 18,641
miles (30,000 kilometers) whichever expires first. Any unexpired portion of this limited warranty
will be transferred to subsequent owners, upon the resale of the motorcycle during the warranty
period.
THERE IS NO OTHER EXPRESS WARRANTY (OTHER THAN THE SEPARATE
MOTORCYCLE AND NOISE WARRANTIES) ON THE MOTORCYCLE. ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE IS LIMITED
TO THE DURATION OF THIS WARRANTY.
The warranty period shall begin on the date the motorcycle is delivered to the first retail purchaser
or, if the motorcycle is placed in service as a demonstrator or company vehicle prior to sale at
retail, on the date it is first placed in service.
THE FOLLOWING ITEMS ARE NOT COVERED BY THE EMISSION CONTROL SYSTEM
WARRANTY
1. Failures which arise as a result of misuse, alterations, accident or nonperformance of
maintenance as specified in the Owner's Manual.
2. The replacement of parts (such as spark plugs, fuel and oil filters, etc.) used in required
maintenance.
3. Any motorcycle on which the odometer mileage has been changed so that the mileage
cannot be determined.
4. TO THE FULLEST EXTENT ALLOWED BY LAW, HARLEYDAVIDSON AND ITS
DEALERS SHALL NOT BE LIABLE FOR LOSS OF USE, INCONVENIENCE, LOST TIME,
COMMERCIAL LOSS OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you.
Other Rights
This warranty gives you specific legal rights, and you may have other rights which vary from state
to state.
Recommendations for Required Maintenance
It is recommended that any emission system maintenance be performed by an authorized Harley
Davidson dealer using genuine HarleyDavidson replacement parts. The maintenance,
replacement or repair of the emissions control system may be performed by any other qualified
service outlet or individual. Nongenuine parts may be used only if such parts are certified to
comply with U.S. Environmental Protection Agency Standards.
Maintenance Scheduling
Regular Service Intervals
Regular lubrication and maintenance will help keep your new HarleyDavidson operating at peak
performance. Your HarleyDavidson dealer knows best how to service your motorcycle with
factory approved methods and equipment assuring you of thorough and competent workmanship.
NOTES:
Refer to Regular Service Intervals: 2009 VRSC Models. Regular maintenance interval
operations are required to keep your new motorcycle warranty in force. The use of other
than HarleyDavidson approved parts and service procedures may void the warranty. Any
alterations to the emission system components, such as the exhaust system, may be in
violation of Federal and State laws.
Refer to Owner's Maintenance Records. When servicing your motorcycle, bring this
owner's manual to the dealership and complete information needed in the blank columns
listed.
If you operate your motorcycle under adverse conditions
(severe cold, extreme heat, very dusty environment, very
bad roads, through standing water, etc.), you should
perform the regular maintenance intervals more frequently
to ensure the safe operation of your motorcycle. Failure to
maintain your motorcycle could result in death or serious
injury. (00094a)
Regular Service Intervals: 2009 VRSC Models
ITEM PROCEDURE 1000 5000 10,000 15,000 20,000 25,000 NOTES

SERVICED MI. MI. MI. MI. MI. MI.
1600 8000 16,000 24,000 32,000 40,000

KM KM KM KM KM KM
Engine oil and Replace X X X X X X
filter
Oil lines and Inspect for leaks X X X X X X 1
brake system
Air cleaner Inspect, service as required X X X X X X
Tires Check pressure, inspect X X X X X X
tread
Clutch fluid Check level and condition X X X X X X
Rear belt and Inspect, adjust belt X X X X X X 1
sprockets
Throttle, brake Check, adjust and lubricate X X X X X X 1
and clutch
controls
Jiffy stand Inspect and lubricate X X X X X X 1
Brake fluid Check levels and condition X X X X X X 5
Brake pads Inspect for wear X X X X X X
and discs
Spark plugs Inspect X X X
Replace X X
Electrical Check operation X X X X X X
equipment and
switches
Front fork oil Replace every 50,000 miles 80,000 1
kilometers
Steering head Adjust X X 1, 2
bearings
Valve lash Inspect valve lash every 15,000 miles 1, 4
24,000 kilometers and adjust if necessary
Cooling Inspect; check clamps for X X X 1
system tightness, check coolant
freeze point
Coolant Replace every 30,000 miles 48,000 1
kilometers
Radiator Clean X X X X X X
Critical Check tightness X X X 1
fasteners
Battery Check battery and clean 3
connections
Wheel spokes Check for tightness X X X 1
(If so
equipped)
Exhaust Inspect for leaks, cracks, X X X X X X 3
system and loose or missing
fasteners or heat shields
Road test Verify component and X X X X X X
system functions
NOTES: 1. Should be performed by an authorized HarleyDavidson dealer, unless you
have the proper tools, service data and are mechanically qualified.
2. Disassemble, lubricate and inspect every 30,000 miles 48,000 kilometers .
3. Perform annually.
4. Could vary with frequency of operation and riding style.
5. Change D.O.T. 4 and flush brake system every two years.
Owner's Maintenance Records
SERVICE MILE INTERVAL DATE DEALER TECHNICIAN TECHNICIAN
NUMBER NAME SIGNATURE

1000 MI (1600 KM)
5000 MI (8000 KM)
10,000 MI (16,000 KM)
15,000 MI (24,000 KM)
20,000 MI (32,000 KM)
25,000 MI (40,000 KM)
30,000 MI (48,000 KM)
35,000 MI (56,000 KM)
40,000 MI (64,000 KM)
45,000 MI (72,000 KM)
50,000 MI (80,000 KM)
Service Literature
Refer to Service Literature: 2009 VRSC Models. Visit any HarleyDavidson dealer or go to
www.harleydavidson.com to purchase a service or parts manual for your motorcycle. Factory
authorized manuals are the most complete and detailed source of information outside of your
HarleyDavidson dealer.
Service Literature: 2009 VRSC Models
DOCUMENT LANGUAGE PART NUMBER

Service Manual English 9950109
Electrical Diagnostics Manual English 9949909
Service and Electrical Diagnostics Manual French 9950109FR
Service and Electrical Diagnostics Manual German 9950109DE
Service and Electrical Diagnostics Manual Spanish 9950109ES
Service and Electrical Diagnostics Manual Italian 9950109IT
Parts Catalog English 9945709
HD Michigan, Inc. Trademark Information
Harley, HarleyDavidson, HD, Bar & Shield, Digital Tech, Digital Technician, Digital Technician II,
Destroyer, Deuce, Dyna, Electra Glide, Evolution, Fat Boy, Glaze, Gloss, HD, HDnet.com, HD,
Harley, Heritage Softail, Heritage Springer, Low Rider, Night Rod, Night Train, Profile, Revolution,
Road Glide, Road King, Rocker, Softail, Sportster, Sun Ray, Sunwash, Tech Link, Twin Cam 88,
Twin Cam 88B, Twin Cam 96, Twin Cam 96B, Twin Cam 103, Twin Cam 103B, Twin Cam 110,
Twin Cam 110B, TourPak, Screamin' Eagle, Softail, Super Guide, Super Premium, SYN3, Ultra
Glide, VRod, VRSC, Wide Glide, and HarleyDavidson Genuine Motor Parts and Genuine Motor
Accessories are among the trademarks of HD Michigan, Inc.
Product Registered Marks
Allen, Amp Multilock, Bluetooth, Brembo, Delphi, Deutsch, Dunlop, Dynojet, Fluke, G.E.
Versilube, Gunk, Hydroseal, Hylomar, Kevlar, Lexan, Loctite, Lubriplate, Keps, K&N, Magnaflux,
Marson ThreadSetter Tool Kit, MAXI fuse, Molex, MPZ, Mulitilock, Novus, Packard, Pirelli,
Permatex, Philips, PJ1, Pozidriv, Robinair, S100, Sems, Snapon, Teflon, Threadlocker, Torca,
Torco, TORX, Tufoil, Tyco, Ultratorch, Velcro, XActo, and XM Satellite Radio are among the
trademarks of their respective owners.

2009 V Rod Muscle Owner's Manual

Uploaded by

Copyright:

Available Formats

2009 V Rod Muscle Owner's Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

2009 V Rod Muscle Owner's Manual

Uploaded by

Copyright:

Available Formats

2009

POSITION DESCRIPTION POSSIBLE VALUES

CODE MODEL CODE MODEL

LABEL PART NO. DESCRIPTION LOCATION

Spark plug torque 17 ft­lbs 23 Nm

ITEM U.S. LITERS

ITEM DOMESTIC INTERNATIONAL

GEAR DOMESTIC INTERNATIONAL

ITEM VRSCAW VRSCDX VRSCF

ITEM VRSCAW VRSCDX VRSCF

MOUNT SIZE NUMBER

LAMP DESCRIPTION BULBS CURRENT DRAW H­D PART

(ALL LAMPS 12 VOLT) REQUIRED (AMPERAGE) NUMBER

VRSCAW, VRSCF high beam 1 5.10 67717­01

SWITCH REMOVE FUNCTIONS

STEP ACTION WAIT FOR CONFIRMATION NOTES

STEP ACTION WAIT FOR CONFIRMATION NOTES

GEAR CHANGE MPH KPH

GEAR CHANGE MPH KPH

HARLEY­ VISCOSITY HARLEY­ LOWEST AMBIENT COLD WEATHER

READING PERCENT 3 AMP 6 AMP 10 AMP 20 AMP

(VOLTS) OF CHARGE CHARGER CHARGER CHARGER CHARGER

40 minutes 50 minutes 5 minutes

15 minutes 40 minutes 35 minutes

30 minutes 5 minutes 5 minutes

PRODUCT PART FRAME BODY WHEELS DENIM CHROME/

NUMBER PANELS FINISH SATIN

ITEM PROCEDURE 1000 5000 10,000 15,000 20,000 25,000 NOTES

1600 8000 16,000 24,000 32,000 40,000

SERVICE MILE INTERVAL DATE DEALER TECHNICIAN TECHNICIAN

NUMBER NAME SIGNATURE

DOCUMENT LANGUAGE PART NUMBER

You might also like

Spark plug torque 17 ftlbs 23 Nm

LAMP DESCRIPTION BULBS CURRENT DRAW HD PART

VRSCAW, VRSCF high beam 1 5.10 6771701

HARLEY VISCOSITY HARLEY LOWEST AMBIENT COLD WEATHER