EP 1110 1 8 - Vol - 02

EP 1110-1-8
Volume 2
April 2014
Construction Equipment
Ownership and Operating
Expense Schedule
Region II
EP 1110-1-8
30 Apr 14
DEPARTMENT OF THE ARMY EP 1110-1-8
U.S. Army Corps of Engineers
Washington, DC 20314-1000
REPLY TO
ATTENTION OF:
CECW-EC
Pamphlet
No. 1110-1-8 30 April2014
Engineering and Design

CONSTRUCTION EQUIPMENT OWNERSHIP AND
OPERATING EXPENSE SCHEDULE
1. Purpose. This pamphlet is authorized by and established in accordance with Federal

Acquisition Regulation (FAR) 31.105 and USAGE Acquisition Instructions (UAI) SUBPART
31.105. This pamphlet establishes predetermined equipment ownership and operating expense
rates for construction equipment. This pamphlet also establishes a method to calculate
equipment ownership and operating I:)Xpense rates for construction equipment when the
predetermined rates are not considered appropriate. The overall intent of this pamphlet is to
determine equipment costs that are fair and reasonable. Expense factors for calculating dredge
plant and marine equipment costs are provided in chapter 4.
2. Applicability. This pamphlet applies to all USAGE commands. It is applicable to all

solicitations and contracts for construction expected to exceed the Simplified Acquisition
Threshold of $150,000 when actual cost data for both ownership and operating costs cannot be
determined. The pamphlet is published in 12 volumes and a description of each volume's
corresponding geographic region is provided in Appendix A.
3. Distribution Statement. Approved for public release, distribution is unlimited.
4. References. See Appendix A.
FOR THE COMMANDER:
12 Appendices
(See Table of Contents)
Chief of Staff
This pamphlet supersedes EP 1110-1-8, dated 30 November 2011.

EP 1110-1-8
30 Apr 14
[This page intentionally left blank]
2
DEPARTMENT OF THE ARMY EP 1110-1-8
U.S. Army Corps of Engineers
CECW-EC Washington, DC 20314-1000
Pamphlet
No. 1110-1-8, Vol. 2 30 April 2014
Engineering and Design

CONSTRUCTION EQUIPMENT OWNERSHIP AND
OPERATING EXPENSE SCHEDULE
TABLE OF CONTENTS
Paragraph Page
Chapter 1. Introduction
Use 1.1 1-1

Regions 1.2 1-1
Decision Flow Process 1.3 1-1
How to Obtain Assistance 1.4 1-1
How to Obtain CHECKRATE 1.5 1-1
How to Obtain this Publication 1.6 1-2
Chapter 2. Methodology for Construction Equipment
Contents 2.1 2-1

Basis for Equipment Rates 2.2 2-1
Total Hourly Rate 2.3 2-1
Average, Difficult, or Severe Conditions 2.4 2-2
Determination of Condition 2.5 2-2
General 2.6 2-3
Truck Selection 2.7 2-3
Crawler Tractor Selection 2.8 2-3
Equipment Accessories 2.9 2-3
List Price and Accessories 2.10 2-3
Discount Code (DC) 2.11 2-3
Sales or Import Tax 2.12 2-4
Freight 2.13 2-4
Total Equipment Value 2.14 2-4
Economic Life (LIFE) 2.15 2-4
Working Hours Per Year (WHPY) 2.16 2-4
Salvage Value (SLV) 2.17 2-4
Salvage Value Percentage 2.18 2-5
Ownership Elements 2.19 2-5
Depreciation 2.20 2-5
i
EP 1110-1-8, Vol. 2
30 Apr 14
Facilities Capital Cost of Money (FCCM) 2.21 2-6

Operating Cost Elements 2.22 2-6
Fuel Cost 2.23 2-6
Filters, Oil, and Grease 2.24 2-8
Repair Cost 2.25 2-9
Tire Wear Cost 2.26 2-11
Tire Repair Cost 2.27 2-12
Standby Hourly Rate 2.28 2-12
Computation Example 2.29 2-13
Chapter 3. Adjustments to Hourly Rates
Contents 3.1 3-1

Basis for Equipment Rates 3.2 3-1
Equipment Rate Adjustment Tables 3.3 3-1
Determination for Use of Equipment Rates in Tables 2-1
and 2-2 3.4 3-1
Rate Adjustments 3.5 3-1
Changes in Operating Conditions 3.6 3-2
Change in Cost of Money Rate (CMR) 3.7 3-2
Actual Work Hours Greater than 40 Hours per Week 3.8 3-3
Changes in Fuel Cost 3.9 3-3
Adjustments to Filters, Oil, and Grease (FOG) Cost 3.10 3-4
Equipment of Different Age than Table 2-1 3.11 3-4
Rate Adjustment for Overage Equipment 3.12 3-5
Standby Rate Adjustment for Equipment of a Different Age
than Table 2-1 3.13 3-6
Equipment Purchased Used 3.14 3-7
Rate Calculation Examples 3.15 3-7
Chapter 4. Methodology for Dredging Plant and Marine Equipment
Contents 4.1 4-1

General 4.2 4-1
Time Available to Dredge 4.3 4-1
Life 4.4 4-2
Annual Hours Available 4.5 4-2
Salvage Value (SLV) 4.6 4-3
Ownership Cost 4.7 4-3
Depreciation Factor 4.8 4-4
The Cost of Money Rate (CMR) 4.9 4-4
Other Ownership Elements 4.10 4-4
Hourly Operating Cost 4.11 4-5
ii
EP 1110-1-8, Vol. 2
30 Apr 14
Prime and Secondary Power 4.12 4-5

Water, Lube, and Supplies (WLS) 4.13 4-5
Repair Factor (RPR) 4.14 4-6
Standby Rate 4.15 4-7
Rates 4.16 4-7
Allowance for Additional Capital Improvements 4.17 4-7
Overage Plant 4.18 4-7
Dredging Plant Purchased Used 4.19 4-8
Rate Calculation Example 4.20 4-8
Appendix A - References A-1

Appendix B - Area Factors B-1
Appendix C - Guide for Selecting Operating Conditions C-1
Appendix D - Equipment Hourly Calculation Factors D-1
Appendix E - Economic Indexes for Construction Equipment E-1
Appendix F - Tire Description and Tire Cost F-1
Appendix G - Tire Life and Tire Wear Factors G-1
Appendix H - Manufacturer List H-1
Appendix I - Federal Cost-of-Money Rate I-1
Appendix J - Equipment Accessories J-1
Appendix K - Ground Engaging Component Costs Included in Repairs (RCF) K-1
Appendix L - Guide for Estimating Drill Steel and Drill Bit Costs L-1
Glossary Glossary-1
Index Index-1
iii
EP 1110-1-8, Vol. 2
30 Apr 14
iv
EP 1110-1-8, Vol. 2
30 Apr 14
CHAPTER 1
Introduction
1.1 Use. The use of this pamphlet is for rate determination on construction contracts,
dredging contracts, and negotiated procurements and relates only to contractor-owned
equipment. The overall intent of the pamphlet is to determine equipment costs that are
fair and reasonable.
a. This pamphlet shall be used for determining hourly equipment rates that are
contained in the independent government estimate.
b. The use of this pamphlet will be required by contractors for pricing contractor-
owned equipment in negotiated procurements when:
(1) Cost or pricing data is not required, as defined in Federal Acquisition

Regulation (FAR) Part 15.4, Contract Pricing.
(2) Cost or pricing data is required and the actual cost data to support either
ownership or operating costs for equipment or equipment groups of similar model and
series is not available.
(3) Cost or pricing data is required and available, but all or part of the data is
determined not to be in accordance with the FAR cost principles.
1.2 Regions. This pamphlet is published in 12 volumes, each volume uses pricing and
factors developed for a specific geographic region. The numbering of the pamphlets
volume corresponds to its respective region. A listing of the volumes along with a
description of the geographic region is contained in Appendix A.
1.3 Decision Flow Process. A flow chart (figure 1-1) is provided at the end of this
chapter to help the user better understand the process for developing an hourly
equipment rate. The flow chart shows the decision points that allow the user to decide
whether to use the predetermined rate tables or calculate the rate using the method
shown in figure 2-1 or using CHECKRATE (also see paragraph 3.4).
1.4 How to Obtain Assistance. When assistance is needed in understanding the

methodology for calculating equipment rates, contact the Chief, Cost Engineering
Branch, Engineering and Construction Division, Walla Walla District, U.S. Army Corps
of Engineers, (CENWW-EC-X), 509-527-7511, 509-527-7510, or visit the Web site at
http://www.nww.usace.army.mil/.
1.5 How to Obtain CHECKRATE. A Microsoft Excel® workbook, named

“CHECKRATE,” has been developed to calculate equipment rates using the
1-1
EP 1110-1-8, Vol. 2
30 Apr 14
methodology required by this pamphlet. The user must have Microsoft Excel® to run
the application. The factors needed in the hourly cost calculations are located in the
appendixes of this pamphlet. A copy of the workbook may be obtained by going to the
Cost Engineering webpage on the Walla Walla District website
http://www.nww.usace.army.mil/. by selecting "Missions", and selecting "Cost
Engineering”. Expand the Product Support Section by clicking on the plus sign next to
“Construction Equipment Rates (EP 1110-1-8) and CHECKRATE”, then follow the link
to Download CHECKRATE.
1.6 How to Obtain this Publication. Volumes 1-12 of this Engineer Pamphlet are
available in portable document format (PDF) and can be viewed or downloaded at the
official HQUSACE documents webpage at http://www.usace.army.mil/ by selecting
"Library" and selecting "Publications". Additional instructions in Appendix A.
1-2
EP 1110-1-8, Vol. 2
30 Apr 14
Finished. The methodology in this pamphlet should not be
START Is the equipment contractor owned ? (See Appendix A) NO
used for rental or leased equipment.
YES
Is the use of this pamphlet required in accordance with Chapter 1, paragraph 1-1? NO Use the contractor's actual cost and pricing data to determine a rate.
YES
A detailed methodology for equipment purchased used is not included in this
Was the equipment purchased new by the contractor? NO
pamphlet (See paragraph 3.14, 4.19 and applicable sections of the FAR)
YES
Land Based Equipment Marine equipment

Is this land based or marine equipment?
Use the methodology found in Chapter 4 for determining

Is the equipment in Table 2-1?
For actual or equivalent equipment, use a rate for Marine Equipment.
YES the tables in chapter 2 and make the
required rate adjustments or use Use Table 2-1
Is the equipment in Table 2-1 YES methodology to calculate a rate (see
equivalent in configuration (size, figure 2-1 or CHECKRATE)
capacity, and horsepower) and value
to the equipment for which you are
NO determining a rate? (see chapter 3
section I paragraph 3.4) Is the equipment operating in average
severe or difficult conditions? (see
NO YES AVERAGE SEVERE
chapter 2, section II for definition and for
determining authority)
Is there equipment in Table 2-1 that is
equivalent within10% of the Use
DIFFICULT
configuration (size, capacity, and methodology
horsepower) and value to the equipment
for which you are determining a rate? Use the From Table 2-2 use the arithmetic mean of Use severe rate shown in Table
(see chapter 3 section I paragraph 3.4) equipment rate the average and severe equipment rates. 2-2. (Note: if there is no severe
shown in Table (Note: if there is no severe rate for the rate for the equipment see
2-1 equipment see guidance in chapter 2, guidance in chapter 2, section II,
NO section II, paragraph 2-4.) paragraph 2-4.)
Calculate a rate based on the step-by-step

rate computation method shown in Figure 2- Next Page
1 or use CHECKRATE
Figure 1-1. Methodology for Developing an Hourly Ownership and Operating Rate for Construction Equipment
1-3
EP 1110-1-8, Vol. 2
30 Apr 14
Continue
from NO Is the cost of fuel 10% greater than or 10% less
previous NO
than the cost shown in Appendix B?
page Do the actual hours worked
YES exceed 40 hours per week?
The contractor shall be required to furnish copies of all YES

The Department of the Treasury adjusts the CMR fuel supply contracts and invoices to the government to
(Prompt Payment Interest Rate) on or about 1 support fuel cost adjustment. Request for upward
January and 1 July each year. For the current adjustment in the rates will be considered only when fuel
Make adjustments to the FCCM
Prompt Payment Interest Rate see is supplied by recognized distributors of bulk quantities
per the instructions in chapter 3,
http://www.publicdebt.treas.gov/opd/opdprmt2.htm. section II, paragraph 3-8
If the contractor is able to furnish the above information, NO

adjust the fuel cost per the instructions in chapter 3,
Is the Cost of Money Rate (CMR) different from that section II, paragraph 3-9.
shown in chapter 2, section VII or Appendix B?
YES If fuel costs are adjusted FOG costs also need to be

adjusted by applying the same ratio used to adjust the Is the equipment's date of
If the cost of money rate shown in chapter 2, section fuel cost. manufacure different from that in
VII, is not the current rate, the FCCM portion of the Table 2-1 (see chapter 2 section 1,
total hourly rate shall be adjusted. Adjust the Cost paragraph 2-2)?
of Money Rate per the instructions in chapter 3, Equipment is older
section II, paragraph 3-7.
Equipment is newer
If equipment is older than in Table 2-1 determine economic

life by dividing LIFE by Working Hours Per Year. (see Adjust the rate using
chapter3 section II, Paragraph 3-11.a.) Table 3-1 per the NO
instructions found in
chapter3 section II,
Equipment age does not exceed economic life Equipment age exceeds economic life Paragraph 3-11.c.
Adjust the rate using

Adjust the rate using Table
Table 3-1 per the
3-1 per the example found
instructions found in FINISHED (except for standby)
in chapter3 section II,
chapter3 section II,
Paragraph 3-11.a.
Paragraph 3-12.
Figure 1-1. Methodology for Developing an Hourly Ownership and Operating Rate for Construction Equipment&RQW
1-4
EP 1110-1-8, Vol. 2
30 Apr 14
CHAPTER 2
Methodology for Construction Equipment
SECTION I. GENERAL
2.1 Contents. This chapter provides the methodology used to compute the total hourly
ownership and operating rates for construction equipment and marine equipment
(except dredging plant). This detailed methodology includes the formulas and factors
used to develop both total hourly rates and hourly standby rates. If the equipment is
determined to be older than its estimated economic life (overage) or was purchased
used, refer to chapter 3.
2.2 Basis for Equipment Rates. The hourly rates shown in table 2-1 reflect catalog list
prices of equipment manufactured in 2011 (3 years old). List prices for equipment
manufactured in years other than 2011 have been adjusted to a 2011 price level using
economic indexes. Ownership and operating expenses are computed using area
factors, found in appendix B, which are specific to each region and volume. This hourly
rate methodology assumes that equipment furnished to the job is in sound, workable
condition. Furthermore, the methodology applies only to equipment that prime
contractors or subcontractors either own or control. These hourly rates and cost factors
do not represent rental charges for those in the business of renting equipment.
2.3 Total Hourly Rate. Hourly rates for average conditions are shown in table 2-1 and
are computed based on a 40-hour (hr) workweek. The hourly rate is the sum of
ownership and operating costs. Table 2-2 contains all individual rate elements for both
average and severe conditions. An example of the methodology used to compute the
total hourly rate is shown in figure 2-1. For standby calculation, see section IX.
a. Ownership Cost Elements. The ownership portion of the rate consists of an

allowance for depreciation (DEPR) and facilities capital cost of money (FCCM).
b. Operating Cost Elements. Operating costs include allowances for the

following:
(1) Fuel.
(2) Filters, oil, and grease (FOG) (includes servicing).
(3) Repairs (includes maintenance and major overhauls).
(4) Tire wear (replacement).
(5) Tire repair.
2-1
EP 1110-1-8, Vol. 2
30 Apr 14
c. Exclusions to Hourly Rates. Total hourly rates for owning and operating
equipment do not include allowances for the following (it should also be noted that
replacement cost is not included in the rates, as it is not an allowable item of cost per
FAR 31.105(d)(2)(i)):
(1) Operating labor.
(2) Mobilization and demobilization.
(3) Field office overhead expenses.
(4) Home office or general and administrative (G&A) overhead expenses.
(5) Investment tax credit.
(6) Contingency allowance.
(7) Profit.
(8) Parts and labor escalation.
d. Other Ownership Elements. The following elements of cost are not included in
the total hourly rates. These costs are allowable and would normally be included in the
contractor’s field office or home office overhead rate calculation.
(1) License fees, property taxes, storage, and insurance costs are considered
indirect costs and are not included in the total hourly rates.
(2) Jobsite security, inspection fees, recordkeeping, mechanic training, and

highway permits are also not included in the total hourly rates.
SECTION II. OPERATING CONDITIONS
2.4 Average, Difficult, or Severe Conditions. Operating conditions may be average,

difficult, or severe. Hourly rates for both average and severe operating conditions are
determined in accordance with appendix C. The rate for the difficult condition is the
arithmetic mean of the average and the severe rates. When only the average rate is
shown in table 2-2, the rate applies for all operating conditions or as determined by the
contracting officer. Average condition rates are included in both tables 2-1 and 2-2.
Only table 2-2 contains the severe condition rates.
2.5 Determination of Condition. For contract modifications, the contracting officer

determines the equipment operating condition to be used. This determination is based
on contract specifications, site conditions, basis of any supporting evidence, and
guidance in appendix C. Evaluation of operating conditions for equipment not listed in
2-2
EP 1110-1-8, Vol. 2
30 Apr 14
appendix C will be consistent with examples shown in appendix C. The operating

condition of the equipment relates to the average and severe factors as detailed in
appendix D.
SECTION III. EQUIPMENT SELECTION
2.6 General. Equipment shown in table 2-1 is representative of equipment that is

used in general construction. Note that some equipment may require additional
attachments or accessories. Each unit of equipment is grouped into a main group
called a category (CAT) and a subgroup called a subcategory (SUB). This type of
grouping is displayed in table 2-1 and appendix D. Also, an identification number (ID
No.) is assigned to each unit of equipment. The ID No. consists of three parts. The first
three characters are the CAT, the second two characters are the manufacturer's code,
and the last three characters are the sequence number.
2.7 Truck Selection. Because of the large number of possible combinations of

highway truck chassis and bodies, both are listed separately. For estimating purposes,
use the gross vehicle weight (GVW) rating of the truck chassis to make a selection with
the following conditions:
a. The combined weight of the truck chassis, truck body, and payload must not
exceed the GVW rating shown for the truck chassis.
b. The gross combined weight (GCW) of the truck, trailer, and payload must not
exceed the GCW rating shown.
2.8 Crawler Tractor Selection. A wide range of combinations of ripper and various
blade options are available for each crawler tractor. For ease of use, all tractors include
a universal blade attachment. Other blade and ripper attachments are shown
separately and should be substituted for the universal blade to match actual equipment
configuration. Only the hourly expense for those attachments that are required to
perform the work shall be allowed.
2.9 Equipment Accessories. Equipment accessories included on the major pieces of

equipment in table 2-1 are listed in appendix J.
SECTION IV. EQUIPMENT VALUE
2.10 List Price and Accessories. The total list price includes those accessories
normally purchased by the contractor plus required safety features.
2.11 Discount Code (DC). A 7.5-percent discount is used for all equipment except
highway trucks that are discounted at 15 percent. The total discounted price is derived
by subtracting the appropriate discount from the total list price. The identification of the
2-3
EP 1110-1-8, Vol. 2
30 Apr 14
discount is shown in appendix D under column heading DC. Two codes are used to
identify the discount, B equals the basic discount of 7.5 percent and S equals the
special discount of 15 percent.
2.12 Sales or Import Tax. Total state sales tax (which includes local taxes) or import
tax is computed as a percentage of the discounted price. The average tax for the
region is shown in appendix B.
2.13 Freight. Estimated allowances for freight are provided in appendix B. This
allowance includes preparation and delivery. Multiply the shipping weight based on
hundredweight (cwt) by the freight rate to determine freight charges.
2.14 Total Equipment Value(TEV). Freight is added to the total discounted price (which
includes sales tax) to arrive at the TEV. The estimated TEV is indicated in table 2-1
under the column heading VALUE.
SECTION V. LIFE
2.15 Economic Life (LIFE). The expected economic life of the equipment will vary
based on the type of equipment and the condition of use. It is established from
manufacturers’ or equipment associations’ recommendations. The expected economic
life in hours is given in appendix D, under the column heading LIFE, for both average
and severe conditions.
2.16 Working Hours Per Year (WHPY). Annual average operating hours have been
established for equipment working within the region covered by this pamphlet. The
number of WHPY as shown in appendix B is equivalent to 1 year’s use for a single shift
operation. Average annual hours of use per year are determined by reducing the
maximum available hours per year (40 hours per week, 52 weeks per year) to allow for
lost working days due to the following factors:
a. Weather.
b. Employee holidays.
c. Equipment maintenance and repairs.
d. Mobilization and demobilization.
e. Miscellaneous downtime.
SECTION VI. SALVAGE VALUE
2.17 Salvage Value (SLV). The salvage value for equipment is based on
advertisements of used equipment for sale as displayed in current engineering and
2-4
EP 1110-1-8, Vol. 2
30 Apr 14
construction magazines, manufacturer’s recommendations, and the Green Guide

Volumes I and II, Handbook of New and Used Construction Equipment Values,
Equipment Watch.
2.18 Salvage Value Percentage. The salvage value percentage used for each type of
equipment is listed in appendix D under the heading SLV as a percentage of the
equipment value. It is equal for both average and severe conditions.
SECTION VII. OWNERSHIP COST
2.19 Ownership Elements. The ownership portion of the rate consists of allowances for
depreciation (DEPR) and facilities capital cost of money (FCCM). These two cost
elements are computed based on the TEV. Other ownership elements may be allowed
(see paragraph 2.3d.). Total ownership rate per hour is expressed by formula, as
follows:
Ownership Rate/hr = DEPR/hr + FCCM/hr
2.20 Depreciation. The straight-line method is used to compute depreciation.
a. For rubber-tired equipment, the tire cost index (TCI) must first be calculated to
complete the depreciation formula.
b. Hourly depreciation is calculated by dividing the “depreciable" value (TEV less

estimated salvage and tire cost) by the expected economic life of the unit of equipment
in hours. Expressed by formula, depreciation cost equals the following:
DEPR/hr =
[[(TEV )(1 - SLV )] - [(TCI)(Tire Cost )]]
LIFE
Where:
(1) TEV is the total equipment value found in table 2-1.
(2) SLV is the salvage value from appendix D.
(3) TCI is the tire cost index, which is determined by dividing the year of
manufacture tire index by the present-year tire index. For table 2-1, the present year is
2014 and the year of manufacture is 2011 (3 years old). These indexes are listed as
part of appendix E [see Economic Key (EK) 100, All Tires and Tubes].
(4) Tire cost is the total tire and/or conveyor belt cost. The total tire cost is the
sum of the cost of all front, drive, and trailing tires. The tire cost for rubber-tired
equipment is based on tire values at the time the equipment was manufactured.
2-5
EP 1110-1-8, Vol. 2
30 Apr 14
(5) The LIFE is the economic life, which is based on the number of operating
hours throughout the economic life of the equipment (see paragraph 2.15). Hours for
LIFE are provided in appendix D.
2.21 Facilities Capital Cost of Money (FCCM). The FCCM, as defined in FAR 31.205-
10, is included in the total hourly rates. This cost is computed by multiplying a
discounted cost of money rate (CMR) by the average value of equipment and prorating
the result over the annual operating hours. The January 2014 CMR [2.125 percent as
shown in appendix I determined by the Secretary of the Treasury pursuant to Public
Law 92-41 (85 Stat. 97)] is discounted by a reduction of 25 percent to avoid duplication
when applying estimated markups for overhead and profit. The discounted CMR is then
1.70 percent. The Department of the Treasury adjusts the CMR on or about 1 January
and 1 July each year; these revisions are printed in the Federal Register or can be
found at http://www.treasurydirect.gov/govt/rates/tcir/tcir_opdprmt2.htm. The CMR
should be adjusted to the actual period that the equipment is used. Expressed by
formula, FCCM cost equals the following:
FCCM/hr =
(TEV )(AVF)(discounted CMR)
(WHPY)
Where:
a. TEV is the total equipment value found in table 2-1.
b. Average Value Factor (AVF) = [[(N - 1)(1 + SLV )] + 2] / 2N .
c. Number of Years (N) in Depreciation Period = LIFE/WHPY.
d. LIFE is the economic life, which is based on the number of operating hours
throughout the economic life of the equipment (see paragraph 2.15). Hours for LIFE are
provided in appendix D.
e. Discounted CMR = 2.125% (Jan – Jun 2014 rate) / 1.25 = 1.70%.
f. WHPY = Working hours Per Year found in appendix B.
SECTION VIII. OPERATING COST
2.22 Operating Cost Elements. The total operating cost is the sum of the following five
elements: fuel, FOG, repairs, tire wear, and tire repair.
2.23 Fuel Cost. Fuel costs are computed for each gas, diesel, or electric engine.
When the unit of equipment has two engines, as in the case of a truck crane, this
2-6
EP 1110-1-8, Vol. 2
30 Apr 14
methodology treats each engine separately for fuel costs. The hourly fuel cost for each
unit of equipment is shown under the column heading FUEL in tables 2-1 and 2-2.
When the unit of equipment has no engine, no fuel cost will be shown. Hourly fuel costs
are calculated for each engine, as expressed in the following formula:
Fuel Cost/hr = Horsepower (hp) x Fuel Cost/Gallon (gal) x Fuel Factor (gal/bhp-hr)
a. Horsepower is the engines rated horsepower. All horsepower ratings for

engine-driven equipment are listed with the equipment description in table 2-1.
b. Fuel Cost/Gallon is based on values shown in appendix B. See chapter 3 for

fuel cost adjustments.
c. Fuel Factor - Gas or Diesel Fuel. The fuel factor in gallons per brake
horsepower-hour (bhp-hr) is listed in appendix D for both average and severe
conditions. Fuel factors are also listed for both the engine powering the main
equipment (prime engine) and the engine providing power to the carrier vehicle. For
severe conditions, the fuel consumption rate is 30 percent greater than the average
condition rate. Gas or diesel fuel factors are computed by using the following formula:
Horsepower Factor (HPF) x lbs Fuel per bhp - hr

Fuel Factor (Gal/bhp - hr) =
lbs of Fuel per Gal
Where:
(1) HPF is the horsepower factor used in the fuel and electricity consumption
formulas and represents an average percent of full-rated horsepower being used by the
engine. The fuel consumption factors, which are shown in appendix D under column
headings Fuel Factor-Equipment and Fuel Factor-Carrier, are computed based on the
HPF shown under these column headings. This HPF is an estimate of the engine load
under average working conditions. It is necessary to modify the rated horsepower as
engines and motors in actual production do not work at their full-rated horsepower at all
times. Periods spent at idle, travel in reverse, traveling empty, close maneuvering at
part throttle, and operating downhill are examples of conditions that reduce the HPF.
Professional judgment regarding cycle time and equipment loading is applied to
determine this average HPF. Normal field application can also vary according to:
operator efficiency, type of material, type of work cycle, and overall jobsite efficiency.
This pamphlet provides an estimated average HPF, not a specific factor.
(2) Pounds (lbs) fuel per bhp-hr is an average based on a variety of engine
applications from manufacturer engine data. The following represent an average of the
normal application of equipment and are indicative of engine fuel consumption
2-7
EP 1110-1-8, Vol. 2
30 Apr 14
industry wide. Pounds fuel (consumed) per bhp-hr is based on the following averages
and is used consistently throughout this pamphlet:
Gasoline = 0.55 lbs per bhp-hr

Diesel = 0.34 lbs per bhp-hr
(3) Pounds fuel per gallon is the factor that determines the weight of the fuel
consumed. The following are used as constants in this pamphlet:
Gasoline = 6 lbs per gal

Diesel = 7 lbs per gal
d. Fuel Factor - Electricity. Assuming that an electric motor uses 1 kilowatt (kW)
per horsepower (considering all inefficiencies), and using the same HPF for gas or
diesel fuel consumption, the electricity consumption is computed by the following
formula:
Fuel Factor (kW/hr) = HPF x 1 kW per electric hp - hr
e. Fuel and Electricity Cost. The cost per gallon for gasoline and diesel fuel used
to compute the hourly fuel cost is shown in appendix B. The hourly fuel cost for all
gasoline-powered equipment, diesel-powered highway trucks, and truck crane carriers
includes an allowance for Federal and state road taxes, sales taxes, and rental for fuel
storage tanks and pumps. Cost per kilowatt-hour used to compute electricity cost are
also shown in appendix B.
2.24 Filters, Oil, and Grease(FOG) Cost. The FOG cost is computed as a percentage
of the hourly fuel costs.
a. The FOG contains items of cost for routine servicing of the equipment, which
includes the following:
(1) Base wages for servicing labor.
(2) Fringe benefits and labor burden costs for servicing.
(3) Service truck, tools, and fuel truck allowance.
(4) Shop allowance when shop servicing is required.
(5) Other equipment costs for servicing.
(6) FOG material allowance.
2-8
EP 1110-1-8, Vol. 2
30 Apr 14
(7) Taxes and shipping for FOG supplies.
(8) Handling and disposal of hazardous materials and oil.
b. The hourly FOG cost is calculated for each engine using the following formula:
FOG Cost/hr = FOG Factor x Fuel Cost/hr x LAF
Where:
(1) The FOG Factor is the percent allowance expressed as a decimal factor under
each fuel type heading E (electricity), G (gas), or D (diesel). See appendix D.
(2) Fuel cost/hr is a calculated value shown under the column heading FUEL in
tables 2-1 and 2-2.
(3) The LAF (labor adjustment factor) is a decimal factor to account for regional
variations in labor and parts costs. This factor is provided in appendix B.
c. The FOG percentage allowance includes the cost for servicing. For equipment
that is normally serviced by an oiler assigned to the unit of equipment, the FOG
percentage is reduced. This reduction applies to the following equipment: cranes,
draglines, hydraulic excavators, and shovels (except equipment under category
numbers C75, C80.01, C85.11, C85.12, C85.21, C90.01, H25.11, H25.12, H30.01,
H30.02, and M10.32).
d. When a unit of equipment has no engine (therefore no fuel costs calculated)

and the equipment requires some type of fuel (i.e., propane, kerosene), an alternative
hourly fuel and FOG allowance may be used in lieu of the regularly calculated fuel and
FOG hourly costs. A FOG allowance may also be added when the equipment has no
engine and has parts that require FOG. The alternative fuel allowance is added to the
alternative FOG allowance for a total alternative fuel and FOG cost. (See figure 2-1,
5.c.)
2.25 Repair Cost.
a. The repair cost accounts for equipment repairs, maintenance, and major
overhauls (including undercarriage wear, ground engaging tools, and designated
attachments) performed in either the field or the shop. Where tire cost is the cost of the
tires when the equipment was manufactured, use the same TCI and tire cost as shown
in the depreciation calculation (see section 2-20). The estimated hourly rate for repairs
is computed as follows:
2-9
EP 1110-1-8, Vol. 2
30 Apr 14
[(TEV) - [(TCI)(Tire Cost)]] x RF

Repair Cost/hr =
LIFE
Where:
(1) TEV is the total equipment value found in table 2-1.
(2) TCI is the tire cost index, which is determined by dividing the year of
manufacture tire index by the present-year tire index. For table 2-1, the present year is
2014 and the year of manufacture is 2011 (3 years old). These indexes are listed as
part of appendix E [see Economic Key (EK) 100, All Tires and Tubes].
(3) Tire cost is the total tire and/or conveyor belt cost. The total tire cost is the
sum of the cost of all front, drive, and trailing tires. The tire cost for rubber-tired
equipment is based on tire values at the time the equipment was manufactured.
(4) Repair factor (RF) is calculated as follows:
RF = RCF x EAF x LAF
Where:
(5) The RCF (repair cost factor) is shown in appendix D. This factor varies
depending on the operating condition of the equipment (average or severe).
(6) The EAF (economic adjustment factor) is used to adjust the RCF to current
price levels. The EAF is equal to the economic index for the present year divided by the
economic index for the year of manufacture. Indexes listed in appendix E are used to
develop the EAF. Economic indexes are determined as follows:
(a) Economic Index for the Present Year. This is the economic index for the
present year (2014 for table 2-1 calculations). Obtain the economic index from
appendix E. The index is located in the column with the present year and the row with
the type of equipment in question. When the column for the present year has not been
included, the index can be estimated using a straight-line projection.
(b) Economic Index for the Year of Manufacture. This is the economic index for
the year the equipment was manufactured (2011 for table 2-1 calculations). Obtain the
economic index from appendix E. The index is located in the column with the year of
manufacture and the row with the type of equipment in question. When the actual age
of the equipment is beyond the last year of its economic life, the equipment is
considered overage. Economic life is determined by dividing hours of LIFE (from
appendix D) by WHPY (appendix B).
2-10
EP 1110-1-8, Vol. 2
30 Apr 14
(7) The LIFE is the economic life, which is based on the number of operating
hours throughout the economic life of the equipment (see paragraph 2.15). Hours for
LIFE are provided in appendix D.
b. Items Included in the Repair Cost Factor. The estimated percentage

allowances for the RCF are shown in appendix D under the column heading RCF and
are expressed as decimal factors. These RCFs (for both the average and severe
conditions) compensate for the following cost elements:
(1) Mechanic’s labor includes base wages, fringe benefits, supervision, travel, and
all other costs for labor associated with craft workers engaged in the direct repair of
equipment either in the field or the shop.
(2) Repair parts and supplies include those items that are required for all repairs
and major overhauls complete with applicable sales taxes and freight charges.
(3) Service trucks and other equipment used during field or shop repair and
maintenance work including tools.
(4) Supporting repair facilities include field and main repair shops, complete with
parts and supplies inventory, and shop overhead.
2.26 Tire Wear Cost.
a. Tires included on rubber-tired equipment are generally the type and ply rating
recommended as standard tires by the equipment manufacturer. Tire costs include
both tire wear (replacement) and tire repair as individual elements of cost. Conveyor
belt wear is also included under this cost element. The belt wear is treated like
tire wear. The wear factors are listed in the front tire wear factor column in appendix D.
Belt life and cost are listed in appendix F.
b. The formula for calculating tire wear applies to each tire position: front (FT),
drive (DT), and trailing (TT). However, all tires performing the drive function are
considered drive tires and are listed in the drive position. The total hourly tire wear cost
for each unit of equipment is the sum of the hourly cost for each position. The total
hourly tire wear cost equals the current cost of new tires plus the cost of one recapping
divided by the expected life of the new tires plus the life of the recapped tires. This
hourly allowance for determining tire wear cost is expressed in the following formula:
Tire Wear Cost/hr = Tire Cost Factor x Current Tire Cost

Tire Life Factor x Tire Wear Factor x Maximum Tire Life
2-11
EP 1110-1-8, Vol. 2
30 Apr 14
Where:
(1) Tire Cost Factor is estimated at 1.5, which represents the purchase of the
original tire plus one recap. It has been estimated that a recap costs approximately 50
percent of the new tire cost.
(2) Current Tire Cost is the estimated cost that applies to all tires on the
equipment in that position. For example, four new drive tires valued at $500 each would
result in an amount of $2,000 for total drive tire cost. The size and cost of each tire
used in the pamphlet are listed for information in appendix F.
(3) Tire Life Factor is estimated at 1.8, which represents the original tire life plus
one recap. It has been estimated that a recap lasts approximately 80 percent of the life
of a new tire.
(4) Tire Wear Factor is based on the position of the tire, type of equipment, and
condition of use. Tire wear factors have been developed and are listed in appendix D.
These factors will provide a percentage reduction to the maximum tire life. Appendix G
contains the methodology used to develop these factors and a computation example for
a rear dump wagon.
(5) Maximum Tire Life expressed in hours is shown for various new tire types in
appendix F. The tire life is estimated from information provided by Goodyear Tire and
Rubber Company and by using the method and tables in Production and Cost
Estimating of Material Movement with Earthmoving Equipment, Terex Corporation,
Hudson, Ohio.
2.27 Tire Repair Cost. It has been estimated that tire repairs are 15 percent of the total
hourly tire wear cost. The LAF is used to adjust the tire repair cost to account for
regional variations in labor and parts costs. This cost element has been calculated and
listed separately in table 2-2. It is expressed as a formula as follows:
Tire Repair Cost = Total Hourly Tire Wear Cost x 0.15 x LAF
SECTION IX. STANDBY HOURLY RATE
2.28 Standby Hourly Rate. The standby rate is computed by allowing the full FCCM
hourly cost (based on a 40 hour workweek) plus one-half of the hourly depreciation. It
is expressed as a formula, as follows:
Standby Rate/hr = (DEPR/hr x 0.50 ) + FCCM/hr
2-12
EP 1110-1-8, Vol. 2
30 Apr 14
a. Paid standby shall not exceed 40 hours per week (7 calendar days) (based on
a 40 hour workweek) per unit of equipment. Actual operating hours during a week will
be credited against the 40 hours maximum standby allowance.
b. Standby costs will not be allowed during periods when the equipment would
have otherwise been in idle status.
c. When the equipment is purchased used, standby will be computed on the basis
that the equipment was purchased new by the contractor in the year it was actually
manufactured. Refer to chapter 3 for rate adjustments.
SECTION X. RATE CALCULATION EXAMPLE
2.29 Computation Example. Figure 2-1 is an example of how the total hourly rates in
table 2-1 are computed. A blank Equipment Rate Computation Worksheet is included in
appendix A and can be copied as needed.
a. When an hourly rate for a specific unit of equipment is not included in this
pamphlet and a rate must be computed, the methodology contained in chapter 2 shall
be followed. However, when a unit of equipment is not included in this pamphlet and
the necessary factors to compute a rate are not found in appendix D, please contact the
Chief, Cost Engineering Branch, Engineering and Construction Division, Walla Walla
District, U.S. Army Corps of Engineers, for assistance as explained in chapter 1. A
Microsoft Excel® spreadsheet (CHECKRATE) is also available for rate computation
(see chapter 1).
b. See chapter 3 for further guidance on the procedure for rate adjustments.
2-13
EP 1110-1-8, Vol. 2
30 Apr 14
Example: The piece of equipment shown in this example is based on a known piece of
equipment for illustration purposes only.
Use this worksheet to compute an hourly rate for equipment that is not in this pamphlet or is in the pamphlet but not equivalent in
size, capacity, horsepower, or value (see appendix A for blank form).
Region 02
1. EQUIPMENT INFORMATION AND EXPENSE FACTORS
ID No: C90LB001
a. Equipment Specification Data:
(1) Equipment Description: CRANES, MECHANICAL, LATTICE BOOM, TRUCK MTD,
150 TON / 260' BOOM, 8X4
(2) Model and Series: HC-238H II
(3) Present Year or Year of Use: 2014
(4) Year Manufactured: 2011
(5) Horsepower - Equipment: 200
(6) Horsepower - Carrier: 445
(7) Fuel - Equipment: 0-None; 1-electric; 2-gasoline;
3-diesel off-road; 4-diesel on-road; 5-marine gas; Enter number
6-marine diesel 3
from 0 to 6 ==> D-off
- Carrier: 0-None; 1-electric; 2-gasoline;
6-marine diesel
4 D-on
from 0 to 6 ==>
(8) Shipping Weight (cwt): 1,913 cwt
(9) Tire size and number of tires: (Cost of tires based on present year, see 1.a.(3) and App. F):
Size/Ply App F Code No. Unit Price Cost
(a) Front (FT): 14-25/20 ANMB1 4 $2,327 $9,308
(b) Drive (DT): 14-25/20 ANMB1 8 $2,327 $18,616
(c) Trailing (TT): 0 $0 $0
(d) Total Tire Cost: $27,924
(10) List Price + Accessories:
[at Year (yr) of Manufacture] $1,690,826 OR actual purchase price: $0
USE APPENDIX D TO COMPLETE THE FOLLOWING DATA:
b. Category and Subcategory Number: C90 0.04
c. Hourly Expense Calculation Factors:
(1) Economic Key (EK): 20
(2) Condition (C): A=Average D=Difficult S=Severe A AVERAGE
(3) Discount Code (DC): B = 7.5% (0.075) or S = 15.0% (0.15) B 0.075
(4) Life in Hours (LIFE): 20,000
(5) Salvage Value Percentage (SLV): 0.20
(6) Fuel Factor - Equipment [Electric (E) Gas (G) Diesel (D)]: 0.024
(7) Fuel Factor - Carrier (E G D): 0.005
(8) Filter, Oil, and Grease (FOG) Factor (E G D): 0.110
(9) Tire Wear Factor:
(a) Front (FT): 0.66
(b) Drive (DT): 0.58
(c) Trailing (TT): 0.73
(10) Repair Cost Factor (RCF): 0.90
Figure 2-1. Equipment Rate Computation Worksheet Page 1 of 6
2-14
EP 1110-1-8, Vol. 2
30 Apr 14
Region 02
2. EQUIPMENT VALUE
a. List Price + Accessories: [at Year (yr) of Manufacture] = $1,690,826
(1) Discount: (List Price + Accessories) x Discount Code

{1.a.(10)} {1.c.(3)}
($1,690,826 + $0.00) x 0.075 = - [ $126,812 ]
(2) Subtotal {2.a.} - {2.a.(1)} Subtotal = $1,564,014
(3) Sales or Import Tax: Subtotal x Tax Rate

{2.a.(2)} {'Appendix B}
$1,564,014 x 6.00% = $93,841
(4) Total Discounted Price: Subtotal: 2.a.(2) + 2.a.(3) Subtotal = $1,657,855
Freight Rate per

b. Freight: Shipping Weight x cwt
{1.a.(8)} {Appendix B}
1,913 cwt x $8.64 /cwt = $16,528
c. TOTAL EQUIPMENT VALUE (TEV): TOTAL [2.]: = $1,674,383

{2.a.(4)} + {2.b} OR actual purchase price {1a.(10)}
(See chapter 3 for used and overage equipment rate adjustments.)
3. DEPRECIATION PERIOD (N)

a. LIFE / Working Hours Per Year (WHPY) = N
{1.c.(4)} {Appendix B}
20,000 hr / 1,450 hr/yr = 13.79 yrs (N)
4. OWNERSHIP COST
a. Depreciation
(1) Tire Cost Index (TCI):

Tire Index, Year of Tire Index, Present
Manufacture, Year or Year of Tire Cost
{1.a.(4)} / Use, {1.a.(3)} = Index (TCI)
Appendix E, EK=100 Appendix E, EK=100
3929 / 4050 = 0.970
(2) [TEV x (1.0-SLV) - (TCI x Tire Cost)] / LIFE

{2.c.} {1.c.(5)} {4.a.(1)} {1.a.(9)(d)} {1.c.(4)}
[$1,674,383 x (1.0-0.20) - ( 0.970 x $27,924 )] / 20,000 hrs = $65.62 /hr
2-15
EP 1110-1-8, Vol. 2
30 Apr 14
Region 02
4. OWNERSHIP COST (Continued)
b. Facilities Capital Cost of Money (FCCM):

Avg Value
(1) [( N - 1.0 ) x (1.0 + SLV) + 2.0] / (2.0 x N) = Factor
{3.a.} {1.c.5.} {3.a.} (AVF)
[(13.79 yr - 1.0) x (1.0 + 0.20) + 2.0] / (2.0 x 13.79 yr) = 0.629
Adjusted
(2) TEV x AVF x Cost-of-Money / WHPY
{2.c.} {4.b.(1)} {Appendix B} {Appendix B}
$1,674,383 x 0.629 x 1.70% / 1,450 hr/yr = $12.35 /hr
c. TOTAL HOURLY OWNERSHIP COST: TOTAL [4.]: = $77.97 /hr

{4.a.(2)} + {4.b.(2)}
5. OPERATING COST
a. Fuel Costs:
(1) Equipment:
Fuel Cost per

Fuel Factor x Horsepower (hp) x Gallon (gal)
{1.c.(6)} {1.a.(5)} {Appendix B}
0.024 x 200 hp x $3.49 /gal = $16.75 /hr
(2) Carrier:
{ 1.c.(4)}
Fuel Factor x Horse power (hp) x Fuel Cost per gal
{1.c.(7)} {1.a.(6)} {Appendix B}
0.005 x 445 hp x $4.05 /gal = $9.01 /hr
(3) Total Hourly Fuel Cost: Total [5.a.] = $25.76 /hr

{5.a (1)} + {5.a (2)}
b. FOG Cost:
(1) Equipment:
Equipment Hourly Labor Adjustment
FOG Factor x Fuel Cost x Factor (LAF)
{1.c.(8)} {5.a.(1)} {Appendix B}
0.110 x $16.75 /hr x 1.02 = $1.88 /hr
2-16
EP 1110-1-8, Vol. 2
30 Apr 14
Region 02
5. OPERATING COST (Continued)
(2) Carrier:
Carrier Hourly
FOG Factor x Fuel Cost x LAF
{1.c.(8)} {5.a.(2)} {Appendix B}
0.110 x $9.01 /hr x 1.02 = $1.01 /hr
(3) Total Hourly FOG Cost: Total [5.b.] = $2.89 /hr

{5.b.(1)} + {5.b.(2)}
c. Alternative Fuel/FOG Cost: Total [5.c.] = $0.00 hr

(See chapter 2, paragraph 2.24.d. for guidance on when to use.)
d. Repair Cost:
(1) Economic Adjustment Factor (EAF):

EK is from {1c. (1)}
Economic Index, Present Year or Year of / Economic Index, Year of

Use,{1.a.(3)} Manufacture, {1.a.(4)}
Appendix E, EK={1.c.(1)} Appendix E, EK={1.c.(1)}
7368 / 7031 = 1.048
(See table 3-1 for last year of economic life.)
(2) Repair Factor (RF):
RCF x EAF x LAF

{1.c.(10)} {5.d.(1)} {Appendix B}
0.90 x 1.048 x 1.02 = 0.962
(3) Repair Cost:
[TEV - (TCI x Tire Cost)] x RF / LIFE

{2.c.} {4.a.(1)} {1.a.(9)(d)} {5.d.(2)} {1.c.(4)}
[$1,674,383 - (0.970 x $27,924)] x 0.962 / 20,000
(4) Total Hourly Repair Cost: Total [5.d.] = $79.23 /hr
2-17
EP 1110-1-8, Vol. 2
30 Apr 14
Region 02
e. Tire Wear Cost: (Use current price levels. See Appendix F.)
(1) Front Tires (FT):
(1.5 x FT Cost) / (1.8 x FT Wear Factor x Maximum Tire Life Hours)

{1.a.(9)(a)} {1.c.(9)(a)} {Appendix F}
(1.5 x $9,308) / (1.8 x 0.66 x 2,500 hr) = $4.70 /hr
(2) Drive Tires (DT):
(1.5 x DT Cost) / (1.8 x DT Wear Factor x Maximum Tire Life Hours)

{1.a.(9)(b)} {1.c.(9)(b)} {Appendix F}
(1.5 x $18,616) / (1.8 x 0.58 x 2,500 hr) = $10.70 /hr
(3) Trailing Tires (TT):
(1.5 x TT Cost) / (1.8 x TT Wear Factor x Maximum Tire Life Hours)

{1.a.(9)(c)} {1.c.(9)(c)} {Appendix F}
(1.5 x $0.00) / (1.8 x 0.73 x 0 hr) = $0.00 /hr
(4) Total Tire Wear Cost: Total [5.e.] = $15.40 /hr

Sum {5.e.(1)} through {5.e.(3)}
f. Tire Repair Cost:
Total Tire Wear Cost

per Hour x (0.15 x LAF)
{5.e.(4)} {Appendix B}
$15.40 /hr x (0.15 x 1.02) Total [5.f.] = $2.36 /hr
g. TOTAL HOURLY OPERATING COST: Total [5.] = $125.64 /hr

Sum {5.a.} through{ 5.f.}
2-18
EP 1110-1-8, Vol. 2
30 Apr 14
Region 02
6. HOURLY RATES
a. Total Hourly Rate: [based on 40 hours per week (wk)]
Ownership Cost + Operating Cost

{4.c.} {5.g.}
$77.97 /hr + $125.64 /hr = $203.61 /hr
b. Other Work Shifts Hourly Rate:
(Refer to Chapter 3, Adjustments to Rates, for methodology.)
Depreciation + (FCCM x 40 hr/wk / Work hr/wk) + Operating Cost

{4.a.(2)} {4.b.(2)} example:60 hr/wk {5.g.}
$65.62 /hr + ($12.35 /hr x 40 hr/wk / 60 hr/wk) + $125.64 /hr = $199.49 /hr
(example:60 hr/wk)
c. Standby Hourly Rate:
(Refer to Chapter 2, paragraph 2.28 for guidance on use.)
(Depreciation x 0.50) + FCCM

{4.a.(2)} {4.b.(2)}
($65.62 /hr x 0.50) + $12.35 /hr = $45.16 /hr
(Refer to Chapter 3, paragraph 3.12 for guidance for overage equipment.)
See Chapter 3 if rate adjustments are necessary.
2-19
EP 1110-1-8, Vol. 2
30 Apr 14
Table 2-1. Hourly Equipment Ownership and Operating Expense
EXPLANATION OF TABLE HEADINGS
Example unit of equipment: Link Belt, Model HC-238H II.
CAT: C90 is the category number and identifies it as Cranes, Mechanical, Lattice
Boom, Truck Mounted (from appendix D).
ID No.: C90LB001 is the unique identification number for the above Link Belt crane. LB
equals the manufacturer (see appendix H). 001 equals the numeric order of this unit of
equipment within the manufacturer’s listing.
MODEL: HC-238H II is the equipment model number.
EQUIPMENT DESCRIPTION: Specific information for each particular unit of equipment

is described, such as “CRANES, MECHANICAL LATTICE BOOM, TRUCK MTD, 150
TON, 260’ BOOM, 8X4” for the Link Belt crane.
ENGINE HORSEPOWER AND FUEL TYPE: The amount of horsepower and type of
fuel used is stated for the main and carrier engines. The Link Belt crane carrier has a
445-horsepower engine, and the crane has a 200-horsepower engine. The carrier
engine is on-road diesel (D-on) and the crane engine is off road diesel (D-off).
VALUE (TEV): This column reflects the predetermined “equipment cost” used to
compute the rates and is based on equipment purchased new in 2011.
TOTAL HOURLY RATES ($/HR): All ownership and operating expenses for the
average condition are included. All cost elements, including fuel, are totaled in the
AVERAGE column. The STANDBY column includes the hourly allowance for
equipment on legitimate standby status (see section 2.28 for more information).
ADJUSTABLE ELEMENTS: This column shows ownership elements and fuel costs
used to develop the average total hourly rates so they can be adjusted as indicated in
chapter 3. Operating costs may be determined by subtracting the ownership cost
elements (DEPR plus FCCM) from the total hourly rate for the average condition.
CWT: The shipping weight of the equipment is stated in hundredweight.
2-20 2-21
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
Table 2-1. HOURLY EQUIPMENT OWNERSHIP AND OPERATING EXPENSE
REGION 2 ENGINE HORSEPOWER VALUE TOTAL HOURLY ADJUSTABLE
AND FUEL TYPE (TEV) RATES ($/HR) ELEMENTS
CAT ID.NO. MODEL EQUIPMENT DESCRIPTION MAIN CARRIER 2011 ($) AVERAGE STANDBY DEPR FCCM FUEL CWT
A10 AGGREGATE / CHIP SPREADERS

SUBCATEGORY 0.10 SELF-PROPELLED
ROSCO, A LeeBoy COMPANY

A10RS003 SPRH CHIP SPREADER, SELF PROPELLED, 10' 152 HP D-off $120,068 45.23 6.76 11.62 0.95 18.04 149
WIDE, 1.70 CY, 2WD
WIDE, 1.80 CY, 2WD
WIDE, 2.03 CY, 2WD
WIDE, 2.28 CY, 2WD
WIDE, 2.53 CY, 2WD
A10RS008 SPREADPRO CHIP SPREADER, SELF PROPELLED, 16' 205 HP D-off $238,662 77.08 13.56 23.35 1.88 24.33 158
WIDE, 4.50 CY, 4WD
SUBCATEGORY 0.20 TOWED & TAILGATE
AMERICAN ROAD MACHINERY, INC.

A10AR001 TG-505C CHIP SPREADER, TAILGATE, 8' WIDE (ADD $3,345 0.84 0.26 0.45 0.03 0.00 5
DUMP TRUCK)
A10AR002 ODELL 900 CHIP SPREADER, TOWED, 8' WIDE, 3 CY $16,234 4.25 1.21 2.16 0.13 0.00 22
(ADD DUMP TRUCK)
SEALMASTER, INC.
A10SE001 R-1 E2310 CHIP SPREADER, TAILGATE, 8' WIDE, 1.13 $12,802 3.20 0.96 1.71 0.10 0.00 21
CY (ADD DUMP TRUCK)
2-21
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
A10 SEALMASTER, INC. (continued)

A10SE002 R-1 E2500 CHIP SPREADER, TOWED, 8' WIDE, 1.13 CY $15,021 3.75 1.12 2.00 0.12 0.00 30
(ADD DUMP TRUCK)
A15 AIR COMPRESSORS, PORTABLE

SUBCATEGORY 0.10 ROTARY SCREW
DOOSAN PORTABLE POWER

A15DP001 P185WJD AIR COMPRESSOR, 185 CFM, 100 PSI (ADD 56 HP D-off $21,132 11.54 0.98 1.64 0.16 7.04 21
HOSE)
A15DP002 HP375WJD AIR COMPRESSOR, 375 CFM, 150 PSI (ADD 110 HP D-off $45,813 23.37 2.16 3.62 0.35 13.82 38
HOSE)
A15DP003 VHP400WJD AIR COMPRESSOR, 400 CFM, 200 PSI (ADD 174 HP D-off $60,428 34.93 2.85 4.76 0.47 21.86 53
HOSE)
A15DP004 HP450WJD AIR COMPRESSOR, 450 CFM, 150 PSI (ADD 174 HP D-off $60,428 34.93 2.85 4.76 0.47 21.86 53
HOSE)
A15DP010 XHP1070WCAT AIR COMPRESSOR, 1,070 CFM, 350 PSI 400 HP D-off $189,795 88.96 8.98 15.03 1.46 50.26 152
(ADD HOSE)
A15DP011 XP535WCU AIR COMPRESSOR, 535 CFM, 125 PSI (ADD 173 HP D-off $80,288 38.15 3.81 6.37 0.62 21.74 53
HOSE)
A15DP012 HP750WCU-T4I AIR COMPRESSOR, 750 CFM, 150 PSI (ADD 270 HP D-off $123,550 59.27 5.84 9.77 0.95 33.92 87
HOSE)
A15DP013 XP825WCU-T4I AIR COMPRESSOR, 825 CFM, 125 PSI (ADD 270 HP D-off $123,550 59.27 5.84 9.77 0.95 33.92 87
HOSE)
A15DP014 XP1000WCU-T4I AIR COMPRESSOR, 1,000 CFM, 125 PSI 305 HP D-off $206,040 78.41 9.73 16.27 1.59 38.32 104
(ADD HOSE)
A15DP015 HP915WCU-T4I AIR COMPRESSOR, 915 CFM, 150 PSI (ADD 305 HP D-off $102,632 60.61 4.84 8.09 0.79 38.32 104
HOSE)
2-22
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
SULLAIR CORPORATION
A15SR006 125DPQJD AIR COMPRESSOR, 125 CFM, 100 PSI (ADD 76 HP D-off $13,274 13.02 0.61 1.01 0.10 9.55 24
HOSE)
HOSE)
A15SR004 185 AIR COMPRESSOR, 185 CFM, 100 PSI (ADD 78 HP D-off $13,274 13.30 0.61 1.01 0.10 9.80 24
HOSE)
A15SR005 260 AIR COMPRESSOR, 260 CFM, 100 PSI (ADD 80 HP D-off $17,830 14.37 0.83 1.38 0.14 10.05 26
HOSE)
A15SR008 375HDPQJD AIR COMPRESSOR, 375 CFM, 150 PSI (ADD 123 HP D-off $30,409 22.59 1.41 2.36 0.23 15.45 42
HOSE)
HOSE)
A15SR010 600HDTQCA AIR COMPRESSOR, 600 CFM, 150 PSI (ADD 230 HP D-off $65,338 43.71 3.04 5.07 0.50 28.90 100
HOSE)
A15SR011 750HHDTQCA AIR COMPRESSOR, 750 CFM, 175 PSI (ADD 300 HP D-off $76,921 55.56 3.59 6.00 0.59 37.69 103
HOSE)
A15SR002 900XH AIR COMPRESSOR, 900 CFM, 350 PSI (ADD 440 HP D-off $156,758 89.00 7.37 12.31 1.21 55.28 157
HOSE)
A15SR012 1050DTQCA AIR COMPRESSOR, 1,050 CFM, 100 PSI 300 HP D-off $75,716 55.35 3.53 5.90 0.58 37.69 105
(ADD HOSE)
A15SR013 1300HDTQCA AIR COMPRESSOR, 1,300 CFM, 150 PSI 450 HP D-off $134,194 86.49 6.33 10.58 1.04 56.54 156
(ADD HOSE)
A15SR014 1600HDTQCA AIR COMPRESSOR, 1,600 CFM, 100 PSI 450 HP D-off $146,913 88.82 6.84 11.42 1.13 56.54 162
(ADD HOSE)
NO SPECIFIC MANUFACTURER
A15XX019 85G AIR COMPRESSOR, 85 CFM, 100 PSI (ADD 30 HP G $11,482 10.74 0.53 0.87 0.09 7.67 14
HOSE)
2-23
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
A15 NO SPECIFIC MANUFACTURER

(continued)
A15XX020 85D AIR COMPRESSOR, 85 CFM, 100 PSI (ADD 30 HP D-off $21,965 8.03 1.03 1.71 0.17 3.77 24
HOSE)
HOSE)
HOSE)
HOSE)
A15XX024 130 AIR COMPRESSOR, 130 CFM, 100 PSI (ADD 50 HP D-off $25,391 11.43 1.19 1.98 0.20 6.28 18
HOSE)
HOSE)
HOSE)
HOSE)
HOSE)
HOSE)
HOSE)
HOSE)
HOSE)
2-24
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014

(continued)
HOSE)
HOSE)
HOSE)
HOSE)
HOSE)
A15XX038 1200 AIR COMPRESSOR, 1,200 CFM, 125 PSI 360 HP D-off $176,512 81.05 8.35 13.97 1.36 45.23 150
(ADD HOSE)
(ADD HOSE)
(ADD HOSE)
SUBCATEGORY 0.20 SHOP TYPE
A15XX041 60/5 AIR COMPRESSOR, 21 CFM, 60 GAL (ADD 5 HP E $3,781 1.07 0.17 0.27 0.03 0.36 3
HOSE)
A15XX042 60/7.5 AIR COMPRESSOR, 26 CFM, 60 GAL (ADD 7 HP E $4,906 1.43 0.22 0.35 0.04 0.50 3
HOSE)
HOSE)
HOSE)
2-25
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014

(continued)
HOSE)
HOSE)
A20 AIR HOSE, TOOLS & EQUIPMENT

SUBCATEGORY 0.10 AIR DRILL HOSE
A20XX001 AIR HOSE, 0.75", 100', 18 MB AIR $1,694 1.28 0.24 0.46 0.01 0.00 1
DRILL
DRILL
DRILL
DRILL
DRILL
A20XX006 AIR HOSE, 2.50", 100', HARDROCK $5,507 4.16 0.80 1.49 0.05 0.00 3
2-26
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
SUBCATEGORY 0.20 SANDBLAST HOSE
CLEMCO INDUSTRIES CORPORATION

A20CM017 SANDBLAST HOSE, 0.75"ID, 100' LONG USE $461 0.37 0.07 0.13 0.00 0.00 1
AS SAND BLASTING ACCESSORY
SUBCATEGORY 0.30 SANDBLASTERS, BREAKERS, & MISC. AIR TOOLS
CHICAGO PNEUMATIC TOOL CO.

A20CK002 CP-0009A ROTARY / CHIP HAMMER, 8 LB, AIR (ADD 30 20 CFM A $1,011 0.44 0.09 0.15 0.01 0.00 1
CFM COMPRESSOR & BIT COSTS)
A20CK001 CP-0014RR ROTARY / CHIP HAMMER, 15 LB, AIR (ADD 32 CFM A $1,758 0.76 0.14 0.26 0.01 0.00 1
30 CFM COMPRESSOR & BIT COSTS)
A20CK003 CP-0022 ROCK DRILL, 30 LB, AIR (ADD 50 CFM 56 CFM A $1,972 0.87 0.17 0.30 0.02 0.00 1
COMPRESSOR & BIT COSTS)
A20CK005 CP-0069 ROCK DRILL, 55 LB, AIR (ADD 140 CFM 130 CFM A $2,497 1.08 0.21 0.37 0.02 0.00 1
A20CK006 CP-0111-CHLA BREAKER-FOUR BOLT, 25 LB (ADD 50 CFM 45 CFM A $1,234 0.54 0.11 0.19 0.01 0.00 1
A20CK008 CP-1230-S BREAKER-FOUR BOLT, 60 LB (ADD 65 CFM 63 CFM A $1,385 0.61 0.12 0.21 0.01 0.00 1
A20CK010 CP-1240-S BREAKER-FOUR BOLT, 90 LB (ADD 90 CFM 81 CFM A $1,501 0.66 0.13 0.23 0.01 0.00 1
2-27
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
CLEMCO INDUSTRIES CORPORATION

A20CM010 PACKAGE TWO SANDBLASTER, 2 CF CAP, W/0.50" D X 25'L 100 CFM A $4,735 2.13 0.40 0.71 0.04 0.00 4
HOSE (ADD 100 CFM COMPRESSOR &
NOZZLE COST)
A20CM011 PACKAGE SANDBLASTER, 4 CF CAP, W/1.00"D X 25'L 170 CFM A $6,100 2.73 0.51 0.92 0.05 0.00 5
FOUR HOSE (ADD 170 CFM COMPRESSOR &
NOZZLE COST)
A20CM012 PACKAGE SIX SANDBLASTER, 6 CF CAP, W/1.25"D X 25'L 200 CFM A $6,846 3.11 0.57 1.03 0.05 0.00 6
NOZZLE COST)
A20CM013 SANDBLASTER, 60 CF CAP, W/1.25"D X 50'L 450 CFM A $24,534 10.76 1.96 3.54 0.19 0.00 30
NOZZLE COST)
NOZZLE COST)
NOZZLE COST)
A20CM016 SANDBLAST ABRASIVE STORAGE HOPPER, $17,419 7.88 1.44 2.61 0.13 0.00 69
700 CF, 8' DEEP,10' WIDE & 23' HIGH (ADD
SAND BLASTER & ACCESSORIES)
WACKER CORPORATION
A20WC002 EHB11/BL/110 BREAKER/DRILL, 40 LB, ELECTRIC (ADD 2 2 HP E $1,354 0.91 0.11 0.20 0.01 0.12 1
KW GENERATOR & BIT COSTS)
A20WC004 BH 23 BREAKER/DRIVER, 65 LB, W/POWER UNIT 4 HP G $3,948 2.73 0.33 0.59 0.03 0.89 1
(ADD BIT COSTS)
2-28
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
A20XX021 STANDARD 25- PAVEMENT BREAKER, 25-35 LB, HAND 100 CFM A $1,387 0.61 0.12 0.21 0.01 0.00 1
35 LBS HELD (ADD 100 CFM COMPRESSOR & BIT
COSTS)
A20XX022 SILENCED 35- PAVEMENT BREAKER, 35-45 LB, HAND 100 CFM A $1,480 0.64 0.12 0.22 0.01 0.00 1
COSTS)
COSTS)
COSTS)
A20XX025 60 DRY ROCK DRILL, DRY, 60 LB, HAND HELD (ADD 100 CFM A $2,548 1.11 0.21 0.38 0.02 0.00 1
100 CFM COMPRESSOR & BIT COSTS)
A25 ASPHALT PAVING DISTRIBUTORS

SUBCATEGORY 0.00 ASPHALT PAVING DISTRIBUTORS

A25RS006 MAXIMIZER 11 ASPHALT DISTRIBUTOR, 1,900 GAL, 400 $66,056 21.73 5.47 9.91 0.51 0.00 70
GPM, TRUCK MTD (ADD 32,000 GVW
TRUCK)
A25RS008 MAXIMIZER 11 ASPHALT DISTRIBUTOR, 3,000 GAL, 400 $75,589 25.34 6.25 11.34 0.58 0.00 97
TRUCK)
2-29
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
A25XX001 1000G ASPHALT DISTRIBUTOR, 1,000 GAL, 400 $72,390 23.18 5.99 10.86 0.56 0.00 64
TRUCK)
TRUCK)
TRUCK)
A30 ASPHALT PAVERS & MISCELLANEOUS ROAD EQUIPMENT

SUBCATEGORY 0.10 SELF PROPELLED
BARBER-GREENE COMPANY
A30BG004 BG225C ASPHALT FINISHER, 8' WIDE SCREED, 112 HP D-off $376,655 110.38 22.89 40.02 2.88 13.29 336
CRAWLER, W/15' 6" SCREED EXTENSION,
177 CF HOPPER
A30BG005 BG2455D ASPHALT FINISHER, 10' WIDE SCREED, 224 HP D-off $400,709 131.29 24.35 42.58 3.06 26.58 374
CRAWLER, W/19' 6" SCREED EXTENSION,
215 CF HOPPER
A30BG003 BG260D ASPHALT FINISHER, 10' WIDE SCREED, 224 HP D-off $383,153 126.19 21.58 37.29 2.93 26.58 382
WHEEL, W/19' 6" SCREED EXTENSION, 215
CF HOPPER
BLAW KNOX CONSTRUCTION EQUIPMENT CORP.

A30BK011 PF-161 ASPHALT PAVER/FINISHER, 8' WIDE 107 HP D-off $268,628 81.64 15.40 26.69 2.05 12.70 210
SCREED, WHEEL, 181 CF HOPPER
2-30
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
A30 BLAW KNOX CONSTRUCTION EQUIPMENT

CORP. (continued)
SCREED, CRAWLER, 218 CF HOPPER
A30BK019 RW 100 A ASPHALT PAVER, SHOULDER PAVING 105 HP D-off $287,232 85.57 17.31 30.22 2.20 12.46 245
MACHINE, 1'-10' WIDE, BITUMINOUS &
AGGREGATE, WHEEL, 72.5 CF
HOPPER
A30BK020 RW 195 ASPHALT PAVER, SHOULDER PAVING 173 HP D-off $376,205 116.93 22.72 39.68 2.88 20.53 330
AGGREGATE, WHEEL, 73 CF HOPPER
A30BK021 TITAN 325 EPM ASPHALT PAVER, 32.8' WIDE, CRAWLER 176 HP D-off $395,506 122.09 24.03 42.02 3.02 20.88 399
W/DUAL TAMPER SCREED, 270 CF
HOPPER
A30BK022 PF-2181 ASPHALT PAVER, 8' WIDE SCREED, WHEEL, 145 HP D-off $302,465 94.73 17.58 30.54 2.31 17.21 283
2 WHEEL DRIVE, 182 CF HOPPER
A30BK023 PF-4410 ASPHALT PAVER, 8' WIDE SCREED, 145 HP D-off $346,552 105.77 21.06 36.82 2.65 17.21 269
CRAWLER, 155 CF HOPPER
CATERPILLAR INC. ( MACHINE DIVISION)

A30CA013 AP-655D ASPHALT PAVER, 8' WIDE SCREED, 174 HP D-off $273,849 91.48 16.64 29.10 2.09 20.65 402
A30CA002 AP-600D ASPHALT PAVER, 8' WIDE+2' EXT. 174 HP D-off $285,400 95.07 16.32 28.27 2.18 20.65 319
PAVEMASTER SCREED, WHEEL, 230 CF
HOPPER
A30CA008 AP-1000D ASPHALT PAVER, 10' - 12' WIDE 224 HP D-off $330,363 112.87 18.99 32.91 2.53 26.58 468
PAVEMASTER SCREED, WHEEL, 215 CF
HOPPER
2-31
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
A30 CATERPILLAR INC. ( MACHINE DIVISION)

(continued)
A30CA016 AP-1055D ASPHALT PAVER, 10' WIDE SCREED, 224 HP D-off $445,632 141.00 27.09 47.35 3.41 26.58 413
CHAMPION ROAD MACHINERY-PRO PAV (WIRTGEN

A30CH001 780WB ASPHALT PAVER, 8' WIDE SCREED, WHEEL, 110 HP D-off $292,836 88.08 16.87 29.26 2.24 13.05 265
190 CF HOPPER
A30CH002 880WB ASPHALT PAVER, 8' WIDE SCREED, WHEEL, 152 HP D-off $319,405 99.89 18.61 32.34 2.44 18.04 315
190 CF HOPPER
A30CH003 880RTB ASPHALT PAVER, 8' WIDE SCREED, 152 HP D-off $321,640 100.48 19.55 34.17 2.46 18.04 282
CRAWLER-RUBBER TRACK, 190 CF
HOPPER
A30CH004 1010WB ASPHALT PAVER, 10' WIDE SCREED, 152 HP D-off $336,703 104.12 19.60 34.05 2.57 18.04 305
WHEEL, 205 CF HOPPER
A30CH005 1110WB ASPHALT PAVER, 10' WIDE SCREED, 173 HP D-off $367,408 114.95 21.40 37.18 2.81 20.53 343
WHEEL, 225 CF HOPPER
A30CH006 1110RTB ASPHALT PAVER, 10' WIDE SCREED, 200 HP D-off $428,720 133.59 26.06 45.55 3.28 23.73 402
SWIFTRACK CRAWLER-RUBBER TRACK, 225 CF
HOPPER
GEHL COMPANY
A30GC002 1448 ASPHALT PAVER, 8' WIDE SCREED, WHEEL, 25 HP D-off $41,022 13.58 2.43 4.23 0.31 2.97 67
80 CF HOPPER
A30GC004 1648 ASPHALT PAVER, 9' WIDE SCREED, 41 HP D-off $58,964 20.17 3.58 6.26 0.45 4.87 85
2-32
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
SUBCATEGORY 0.20 TOWED
MIDLAND MACHINERY CO
A30MP001 SPD-8 ASPHALT PAVER, SHOULDER PAVING 80 HP D-off $171,148 39.58 8.17 13.69 1.32 8.66 185
A30MP002 SPD-10 ASPHALT PAVER, SHOULDER PAVING 100 HP D-off $191,627 45.57 9.15 15.33 1.48 10.82 275
SUBCATEGORY 0.30 SLURRY SEAL PAVERS (Cold mix)
A30XX001 MINIMAC ASPHALT PAVER, SLURRY SEAL PAVER 8' 110 HP D-off $160,446 32.98 6.42 10.40 1.22 11.13 130
WIDE, SELF PROPELLED, WHEEL, 80 CF
HOPPER
A30XX002 MACROPAVER ASPHALT PAVER, SLURRY SEAL PAVER 8' 110 HP D-off $196,126 36.60 8.03 13.08 1.49 11.13 175
12B WIDE, TRUCK MTD, 12 CF HOPPER (ADD
40,000 GVW TRUCK)
SUBCATEGORY 0.40 MISCELLANEOUS ROAD EQUIPMENT
BLAW KNOX CONSTRUCTION EQUIPMENT CORP.

A30BK024 MC-330 ASPHALT PAVER, MOBILE CONVEYOR, 60" 184 HP D-off $384,465 89.87 17.83 29.72 2.97 19.91 430
WIDE BELT, WHEEL (ADD ASPHALT PAVER
UNIT)

A30CA007 BG-260 D ASPHALT PAVER, ASPHALT WINDROW 107 HP D-off $265,707 59.50 12.46 20.81 2.05 11.58 171
ELEVATOR, WHEEL (ADD ASPHALT PAVER
UNIT)
2-33
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
LEE-BOY
A30LD001 3000 ASPHALT PAVER, ASPHALT FORCE FEED 110 HP D-off $155,482 41.03 7.01 11.61 1.20 11.90 198
LOADER, 30" WIDE BELT, WINDROW OR
LOOSE, WHEEL (ADD ASPHALT PAVER
UNIT)
ROADTEC ( ASTEC INDUSTRIES COMPANY)

A30RT001 SB-1500 ASPHALT PAVER, ASPHALT MATERIAL 300 HP D-off $421,931 110.05 20.10 33.70 3.25 32.46 672
TRANSFER VEHICLE, 15 TON HOPPER, 600
TPH, 65" WIDE CONVEYOR, WHEEL
A30RT007 SB-2500E ASPHALT PAVER, ASPHALT MATERIAL 300 HP D-off $460,712 118.14 21.60 36.09 3.55 32.46 780
TRANSFER VEHICLE, 25 TON HOPPER, 1000
TPH, 69" WIDE CONVEYOR, WHEEL
A35 ASPHALT PAVING KETTLES

SUBCATEGORY 0.00 ASPHALT PAVING KETTLES
AEROIL PRODUCTS COMPANY, INC.

A35AE001 KEB-80T ASPHALT/PAVEMENT KETTLE, 80 GAL, 5 HP G $5,345 4.64 0.35 0.61 0.04 1.11 9
TRAILER W/PUMP & HOSE
2-34
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
A40 ASPHALT & CONCRETE MILLERS / PROFILERS / PLANERS / ROTARY GRINDERS

SUBCATEGORY 0.00 ASPHALT & CONCRETE MILLERS / PROFILERS / PLANERS / ROTARY GRINDERS

A40CA008 PM-200 ASPHALT COLD PLANER, 75" W X 10" D, 575 HP D-off $564,807 283.31 42.28 75.31 4.62 90.30 505
CRAWLER (ADD CUTTING TEETH
COSTS)
A40CA009 PM-201 ASPHALT COLD PLANER, 83" W X 12" D, 650 HP D-off $647,271 323.09 48.44 86.30 5.29 102.08 735
COSTS)
TEREX - CMI (TEREX ROADBUILDING)

A40CW001 PR-950 ASPHALT PROFILER, MAX 12.5' W X 15" D, 950 HP D-off $884,889 452.52 66.23 117.99 7.23 149.20 1,205
COSTS)
ROADTEC ( ASTEC INDUSTRIES COMPANY)

A40RT008 RX-400E ASPHALT COLD PLANER, 40" W X 10" D, 325 HP D-off $403,604 185.29 28.98 51.36 3.30 51.04 470
WHEEL (ADD CUTTING TEETH
COSTS)
COSTS)
COSTS)
COSTS)
2-35
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
A40 ROADTEC ( ASTEC INDUSTRIES

COMPANY) (continued)
COSTS)
A45 ASPHALT RECYCLERS & SEALERS

SUBCATEGORY 0.00 ASPHALT RECYCLERS & SEALERS
AEROIL PRODUCTS COMPANY, INC.

A45AE001 HEPR-52V ASPHALT RESURFACER-PATCHER, 4' WIDE, $13,207 11.83 1.14 2.05 0.11 0.00 11
17.3 SF, 600,000 BTU INFRA-RED HEATER,
TRAILER MTD
A45AE002 HEPR-96V ASPHALT RESURFACER-PATCHER, 8' WIDE, $20,365 21.58 1.77 3.19 0.17 0.00 16
32.0 SF, 1,200,000 BTU INFRA-RED HEATER,
TRAILER MTD
A45AE003 IPRS96V ASPHALT RESURFACER-PATCHER, 10' $46,849 33.82 4.11 7.43 0.39 0.00 17
WIDE, 40.0 SF, 1,420,000 BTU INFRA-RED
HEATER, TRAILER MTD

A45RS001 RA-2000 ASPHALT SPRAY PATCHER, 300 GAL, 80 HP D-off $52,078 29.02 4.55 8.21 0.44 8.66 60
ARTICULATED BOOM - 17' R, TRAILER
MTD
A45RS002 RA-300 ASPHALT SPRAY PATCHER, 400 GAL, 210 HP D-on $167,206 90.89 14.78 26.75 1.40 26.37 179
TELESCOPIC BOOM - 22' EXT, TRUCK
MTD
2-36
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
SEALMASTER, INC.
A45SE003 SP300 DUAL ASPHALT SEALCOATER, 320 GAL, 75 GPM, 30 HP D-off $42,696 21.07 3.71 6.69 0.36 3.25 38
108" WIDE DUAL SPRAY, SQUEEGEE, SELF
PROPELLED
A45SE004 TR-1000 ASPHALT SEALCOATER, 1000 GAL, 50 GPM, 13 HP G $25,805 12.85 2.15 3.85 0.22 2.88 52
88'' WIDE SPRAY BAR, TRAILER MTD
B10 BATCH PLANTS, ASPHALT & CONCRETE

SUBCATEGORY 0.20 CONCRETE
CEMEN TECH
B10CC007 MCD2-50HT BATCH PLANT, CONCRETE DISPENSER, 15 18 HP G $51,470 19.97 2.91 5.00 0.41 3.99 80
CY/HR MAX, W/TWO AGGREGATE BINS, 2
CY/ 1 CY CEMENT BIN/ 7' LONG SLOPING 8"
DIA SCREW WET MIXER/DELIVERER/ 250
GAL WATER TANK/ & METERING PUMP, 2
CY LOAD, TRAILER MTD
B10CC008 MCD5-100 BATCH PLANT, CONCRETE DISPENSER, 30 163 HP G $55,699 58.16 2.94 4.99 0.44 36.16 132
CY/HR MAX, W/TWO AGGREGATE BINS, 5.5
CY/ 1.9 CY CEMENT BIN/ 9' LONG SLOPING
9" DIA SCREW WET MIXER/DELIVERER/ 250
GAL WATER TANK/ & METERING PUMP, 5
CY LOAD, TRUCK MTD
12" DIA SCREW WET MIXER/DELIVERER/
250 GAL WATER TANK/ & METERING PUMP,
8 CY LOAD, TRUCK MTD
2-37
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
B10 CEMEN TECH (continued)

12" DIA SCREW WET MIXER/DELIVERER/
250 GAL WATER TANK/ & METERING PUMP,
8 CY LOAD, TRUCK MTD
B10CC012 210 BBL BATCH PLANT, SILO, CEMENT, 830 CF, 210 18 HP G $24,782 11.33 1.44 2.48 0.20 3.99 35
BARREL (BATCH PLANT
ATTACHMENT)
B10CC011 HS-240 BATCH PLANT, SILO, CEMENT, 38 TON 20 HP E $23,785 8.64 1.38 2.38 0.19 1.24 45
HORIZONTAL 240 BARREL (BATCH PLANT
ATTACHMENT)
B10CC013 300 BBL BATCH PLANT, SILO, CEMENT, 1,200 CF, 300 18 HP G $32,522 13.26 1.89 3.25 0.26 3.99 48
BARRL (BATCH PLANT ATTACHMENT)
B10CC014 BATCH PLANT, CEMENT LOADING AUGER, 5 HP E $7,363 2.76 0.43 0.74 0.06 0.31 10
6" DIA, 19' LONG (BATCH PLANT
ATTACHMENT)
CON-E-CO
B10CL025 MTM 12 BATCH PLANT, CONCRETE MIXER, 12 CY, 200 HP E $305,362 92.53 17.55 30.28 2.41 12.35 130
TILT DRUM, 11.67' DIA, REMOVABLE AXLES,
TRAILER MTD (ADD DRY BATCH
PLANT)
B10CL021 VERSA-PLANT BATCH PLANT, CONCRETE AGGREGATE 35 HP E $93,191 25.55 5.14 8.79 0.74 2.16 190
10 DRY, 40CY/HR, 10 CY AGGREGATE
BATCHER, W/30" X 40' LOADING
CONVEYOR, SCALES & WATER METER
INCLUDED, TRAILER MTD (ADD 5 KW
GENERATOR, WATER TANK & WET
BATCHER)
2-38
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
B10 CON-E-CO (continued)

B10CL015 PLP MODEL 12 BATCH PLANT, CONCRETE AGGREGATE 30 HP E $174,714 47.17 9.68 16.59 1.38 1.85 380
DRY, 200 CY/HR, W/TWO AGGREGATE BINS,
81 TON, 60 CY/ 36"X20' CONVEYOR/ 3 BIN
12 CY AGGREGATE BATCHER/ 30"X33.5'
LOADING CONVEYOR/ & 475 BARREL, 88
TON CEMENT SILO, TRAILER MTD (ADD 110
KW GENERATOR)
B10CL006 LO-PRO 12 BATCH PLANT, CONCRETE AGGREGATE 120 HP E $335,314 94.02 18.95 32.59 2.65 7.41 426
65 TON, 50 CY/ 36"X20' CONVEYOR/ 12 CY
AGGREGATE BATCHER/ 36"X36' LOADING
CONVEYOR/ & 215 BARREL, 35 TON
CEMENT SILO, TRAILER MTD (ADD 140 KW
GENERATOR)
B10CL027 BATCH PLANT, CEMENT SILO, 1,910 CF, 475 $22,495 5.48 1.31 2.25 0.18 0.00 144
BARREL (BATCH PLANT
ATTACHMENT)
B10CL042 BATCH PLANT, SCREW CONVEYOR, 6" DIA, 5 HP E $3,528 1.32 0.21 0.35 0.03 0.31 5
10' LONG (CEMENT SILO
ATTACHMENT)
ATTACHMENT)
ATTACHMENT)
ATTACHMENT)
2-39
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
B10 CON-E-CO (continued)

ATTACHMENT)
ATTACHMENT)
EXCEL MACHINERY LTD.

B10EM001 EXCEL PORT-A- BATCH PLANT, CONCRETE CONTINUOUS 25 HP G $477,194 123.92 26.84 46.13 3.77 5.55 590
PUG PUGG MILL MIXER, 400 CY/HR MAX, W/12 CY
AGGREGATE STORAGE BIN/ 48"X18'
METERING CONVEYOR/ CEMENT SILO, 44
TON, 34.8 CY/ 30" X 37' CONVEYOR,
TRAILER MTD (ADD 200 KW
GENERATOR)
B10EM002 BATCH PLANT, CEMENT SILO, 45 TON 10 HP E $32,542 9.53 1.68 2.84 0.26 0.62 45
HORIZONTAL 350 BARREL (BATCH PLANT
ATTACHMENT)
B10EM003 BATCH PLANT, CEMENT SILO, 2,200 CF $29,016 7.07 1.68 2.90 0.23 0.00 222
(BARREL CAP 550 MAX / 450 MIN) W/DRIVE-
THRU TYPE UNDERSTRUCTURE (BATCH
PLANT ATTACHMENT)
JOHNSON-ROSS (TEREX ROADBUILDING)

B10RC007 BANDIT 5 BATCH PLANT, CONCRETE AGGREGATE 15 HP E $161,690 42.81 9.04 15.52 1.28 0.93 3,000
65 TON, 48 CY/ 36" X 20' CONVEYOR/ 2 BIN 5
CY BATCHER/ 30" X 33.5' LOADING
GENERATOR)
2-40
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
B10 JOHNSON-ROSS (TEREX

ROADBUILDING) (continued)
B10RC032 RUSTLER III BATCH PLANT, CONCRETE AGGREGATE 50 HP E $231,510 64.70 12.88 22.09 1.83 3.09 536
28 TON, 21 CY/ 2 BIN 12 CY BATCHER/ 30" X
33.5' LOADING CONVEYOR/ & 400 BARREL,
75 TON CEMENT SILO, TRAILER MTD (ADD
130 KW GENERATOR)
B10RC006 RUSTLER II BATCH PLANT, CONCRETE AGGREGATE 46 HP E $212,314 59.61 11.77 20.17 1.68 2.81 489
DRY, 160 CY/HR, W/3 AGGREGATE BINS, 71
TON, 52 CY/ 36" X 20' CONVEYOR/ 3 BIN 12
CY BATCHER/ 30" X 33.5' LOADING
CONVEYOR/ 375 BARREL, 70 TON CEMENT
SILO, TRAILER MTD (ADD 130KW
GENERATOR)
B10RC008 BANDIT B12 BATCH PLANT, CONCRETE AGGREGATE 30 HP E $273,885 71.49 15.53 26.74 2.16 1.85 250
DRY, 200 CY/HR, W/THREE AGGREGATE
BINS, 65 TON, 48 CY/ 36" X 20' CONVEYOR/ 3
BIN 12 CY BATCHER/ 30" X 33.5' LOADING
GENERATOR)
B10RC027 BATCH PLANT, CONCRETE MIXER, 4.5 CY, 40 HP E $163,019 45.37 9.44 16.30 1.29 2.47 34
TILT DRUM, SKID MTD (ADD DRY BATCH
PLANT)
PLANT)
PLANT)
2-41
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
B10 JOHNSON-ROSS (TEREX

ROADBUILDING) (continued)
PLANT)
PLANT)
B10RC016 MOBILE MIXER BATCH PLANT, CONCRETE MIXER, 4.5CY, 75 HP E $261,876 75.38 14.64 25.13 2.07 4.63 420
TILT DRUM TYPE, REVOLVING LIFT STAND,
TRAILER MTD (ADD DRY BATCH PLANT &
POWER)
STEPHENS MANUFACTURING CO., INC.

B10SN031 DC-12 BATCH PLANT, CONCRETE AGGREGATE 25 HP E $81,958 22.84 4.23 7.15 0.65 1.54 340
DRY, 100 CY/HR, W/2 BIN 12 CY BATCHER/
24" X 41' LOADING CONVEYOR/ & 311
BARREL, 58 TON CEMENT SILO, TRAILER
MTD (ADD 100 KW GENERATOR)
B10SN033 DC COLT BATCH PLANT, CONCRETE AGGREGATE 30 HP E $158,608 42.11 8.66 14.82 1.25 1.85 340
DRY, 100 CY/HR, W/2 BIN 12 CY BATCHER/
30" X 33.5' LOADING CONVEYOR/ & 311
BARREL, 58 TON CEMENT SILO, TRAILER
B10SN032 MUSTANG 5 BATCH PLANT, CONCRETE AGGREGATE 30 HP E $126,801 34.59 6.81 11.61 1.00 1.85 420
DRY, 160 CY/HR, W/3 AGGREGATE
STORAGE BINS, 29.6 TON, 40 CY/ 3 BIN 5 CY
BATCHER/ 30" X 33.5' LOADING CONVEYOR/
& 251 BARREL, 47 TON CEMENT SILO,
GENERATOR)
2-42
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
B10 STEPHENS MANUFACTURING CO., INC.

(continued)
B10SN034 STALLION BATCH PLANT, CONCRETE AGGREGATE 20 HP E $176,597 45.55 9.69 16.59 1.39 1.24 360
DRY, 160 CY/HR, W/3 AGGREGATE BIN
STORAGE, 70 TON, 48 CY/ 2 BIN 10 CY
GENERATOR)
B10SN036 MUSTANG 10 BATCH PLANT, CONCRETE AGGREGATE 45 HP E $165,795 45.47 9.07 15.51 1.31 2.78 500
DRY, 160 CY/HR, W/3 AGGREGATE BIN
GENERATOR)
B10SN035 THOROUGH- BATCH PLANT, CONCRETE AGGREGATE 30 HP E $185,803 48.86 10.23 17.51 1.47 1.85 300
BRED DRY, 180 CY/HR, W/4 AGGREGATE BIN
GENERATOR)
SUBCATEGORY 0.30 PUGMILL
KOLBERG - PIONEER, INC

B10KB001 52 PORTABLE BATCH PLANT, PUGMILL, CONTINUOUS 95 HP E $189,136 45.69 8.80 14.67 1.46 5.87 190
PUGMILL MIXER, 48" DIA TWIN SHAFT X 6' LONG, W/9
CY FEEDER HOPPER/ 36" X 11.5' BELT
FEEDER/ 30" X 27' CONVEYOR/ WATER OR
ASPHALT PUMP & METER (ADD 95 KW
GENERATOR & ANY MATERIAL
FEEDS)
2-43
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
B10 KOLBERG - PIONEER, INC (continued)

B10KB002 52S PORTABLE BATCH PLANT, PUGMILL, CONTINUOUS 220 HP E $337,591 86.27 15.85 26.49 2.60 13.59 230
PUGMILL MIXER, 48" DIA TWIN SHAFT X 8' LONG,
W/13 CY FEEDER HOPPER/ TWO - 36" X 11.5'
BELT FEEDERS/ 2ND 11 CY FEEDER
HOPPER/ 30" X 27' CONVEYOR/ WATER OR
ASPHALT PUMP & METER (ADD 220 KW
GENERATOR & ANY MATERIAL
FEEDS)
B15 BROOMS, STREET SWEEPERS & FLUSHERS

SUBCATEGORY 0.00 BROOMS, STREET SWEEPERS & FLUSHERS
BROCE MANUFACTURING COMPANY

B15BM001 RJ-350 BROOM, 8' BROOM PATH, PAVEMENT, SELF 80 HP D-off $49,050 21.00 3.12 5.52 0.36 8.66 50
PROPELLED
ELGIN SWEEPER COMPANY

B15EC002 PELICAN P STREET SWEEPER, 10' BROOM PATH, 3.5 100 HP D-off $158,731 48.71 9.99 17.61 1.18 10.82 128
CY HOPPER, 180 GAL WATER TANK, SELF
PROPELLED
B15EC001 EAGLE F STREET SWEEPER, 10' BROOM PATH, 4.5 49 HP D-off 170 HP D-on $220,385 61.47 13.81 24.35 1.63 9.43 150
CY HOPPER, 280 GAL WATER TANK, DUAL
ENGINE, SELF PROPELLED
B15EC003 BROOM BEAR STREET SWEEPER, 12' BROOM PATH, 4.5 230 HP D-off $210,820 76.45 13.39 23.65 1.56 24.88 213
FL42H CY HOPPER, 350 GAL WATER TANK, SELF
PROPELLED
B15EC004 MEGAWIND STREET SWEEPER AND CATCH BASIN 115 HP D-off 230 HP D-off $233,543 73.13 14.87 26.27 1.73 17.26 238
CLEANER, 12' BROOM PATH, 13 CY
HOPPER, 335 GAL WATER TANK, SELF
PROPELLED
2-44
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
M-B COMPANIES, INC.

B15MB001 MT-AR STREET SWEEPER, 7' BROOM PATH, $8,629 2.08 0.55 0.97 0.06 0.00 10
W/SPRINKLER AND 152 GAL WATER TANK,
PTO DRIVE (ADD 45-100 HP
TRACTOR)
B15MB002 HT STREET SWEEPER, 7' BROOM PATH, $10,425 2.54 0.67 1.17 0.08 0.00 12
PTO DRIVE (ADD 45-100 HP
TRACTOR)
B15MB003 53T STREET SWEEPER, 7' BROOM PATH, $15,164 3.70 0.92 1.62 0.11 0.00 18
TOWED, HYDRAULIC (ADD TOWING
UNIT)
B15MB004 53MH STREET SWEEPER, 7' BROOM PATH, 18 HP G $17,517 8.40 1.07 1.88 0.13 3.99 17
TOWED (ADD TOWING UNIT)

B15RS005 CHALLENGER II STREET SWEEPER, 7' BROOM PATH, 80 HP D-off $55,818 22.59 3.48 6.14 0.41 8.66 75
SELF PROPELLED
B15RS001 RB-48 STREET SWEEPER, 8' BROOM PATH, 80 HP D-off $42,965 19.62 2.70 4.76 0.32 8.66 52
SELF PROPELLED
TERRAMITE CONSTRUCTION EQUIPMENT

B15TB001 TSS46 STREET SWEEPER, 6' BROOM PATH, 37 HP D-off $23,671 9.96 1.47 2.58 0.18 4.00 34
W/SPRINKLER AND 2 - 50 GAL WATER
TANKS, SELF PROPELLED
2-45
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
B15 TERRAMITE CONSTRUCTION

EQUIPMENT (continued)
B15TB002 TSS48 STREET SWEEPER, 8' BROOM PATH, 37 HP D-off $23,810 9.98 1.48 2.59 0.18 4.00 34
W/SPRINKLER AND 2 - 50 GAL WATER
TANKS, SELF PROPELLED
WALDON, INC.
B15WD001 SWEEPMASTER BROOM, 7.5' BROOM PATH, PAVEMENT, 80 HP D-off $38,669 18.63 2.43 4.28 0.29 8.66 48
250 SELF PROPELLED
B15WD002 SWEEPMASTER BROOM, 90" BROOM PATH, PAVEMENT, 80 HP D-off $40,178 18.98 2.53 4.45 0.30 8.66 48
250 W/SPRINKLER AND 180 GAL WATER TANK,
SELF PROPELLED
B20 BRUSH CHIPPERS

SUBCATEGORY 0.00 BRUSH CHIPPERS
BANDIT INDUSTRIES, INC.

B20BN001 65XP BRUSH CHIPPER, 6" CAPACITY, DISC TYPE, 44 HP G $11,661 13.96 0.73 1.28 0.09 9.76 19
TRAILER MTD
B20BN002 90XP BRUSH CHIPPER, 9" CAPACITY, DISC TYPE, 84 HP G $15,965 25.09 0.99 1.74 0.12 18.63 44
TRAILER MTD
B20BN003 200XP BRUSH CHIPPER, 12" CAPACITY, DISC 140 HP G $18,607 39.89 1.16 2.04 0.14 31.06 58
TYPE, TRAILER MTD
B20BN005 1390XP BRUSH CHIPPER, 13" CAPACITY, DRUM 142 HP G $23,053 41.47 1.44 2.54 0.17 31.50 66
TYPE, TRAILER MTD
B20BN006 1590XP BRUSH CHIPPER, 17" CAPACITY, DRUM 142 HP G $28,584 42.81 1.79 3.16 0.21 31.50 87
TYPE, TRAILER MTD
B20BN007 1890XP BRUSH CHIPPER, 18" CAPACITY, DRUM 142 HP D-off $33,231 25.29 2.04 3.57 0.25 15.36 92
TYPE, TRAILER MTD
2-46
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
MORBARK, INC.
B20MQ001 M12R BRUSH CHIPPER, 12" CAPACITY, DRUM 84 HP D-off $33,457 18.35 2.13 3.75 0.25 9.09 45
TYPE, TRAILER MTD
TYPE, TRAILER MTD
TYPE, TRAILER MTD
B20MQ005 22 RXL BRUSH CHIPPER, LOG CHIPPER, 22" 875 HP D-off $545,782 240.61 34.35 60.62 4.04 94.67 813
CAPACITY, DISC TYPE, TRAILER MTD
B25 BUCKETS, CLAMSHELL

SUBCATEGORY 0.00 BUCKETS, CLAMSHELL
HAWCO (ANVIL ATTACHMENTS)

B25HB001 MWRH-050 BUCKET, CLAMSHELL, 0.5 CY, HEAVY $24,849 5.30 1.58 2.80 0.18 0.00 30
DUTY/DIGGING
DUTY/DIGGING
DUTY/DIGGING
DUTY/DIGGING
DUTY/DIGGING
DUTY/DIGGING
DUTY/DIGGING
2-47
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
B25 HAWCO (ANVIL ATTACHMENTS)

(continued)
DUTY/DIGGING
DUTY/DIGGING
B25HB013 MWHR-500 BUCKET, CLAMSHELL, 5.0 CY, HEAVY $45,202 9.65 2.88 5.09 0.33 0.00 173
DUTY/DIGGING
DUTY/DIGGING
DUTY/DIGGING
B25XX001 1/4SSN BUCKET, CLAMSHELL, 0.2 CY, SQUARE $17,883 3.81 1.14 2.01 0.13 0.00 14
NOSE, STANDARD
NOSE, STANDARD
NOSE, STANDARD
B25XX004 1SSN BUCKET, CLAMSHELL, 1.0 CY, SQUARE $22,069 4.70 1.40 2.48 0.16 0.00 43
NOSE, STANDARD
B25XX005 1-1/4SSN BUCKET, CLAMSHELL, 1.2 CY, SQUARE $23,145 4.93 1.47 2.60 0.17 0.00 49
NOSE, STANDARD
NOSE, STANDARD
NOSE, STANDARD
2-48
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
B25 NO SPECIFIC MANUFACTURER

(continued)
NOSE, STANDARD
NOSE, STANDARD
NOSE, STANDARD
NOSE, STANDARD
NOSE, STANDARD
NOSE, STANDARD
NOSE, STANDARD
NOSE, STANDARD
NOSE, STANDARD
NOSE, STANDARD
NOSE, STANDARD
NOSE, STANDARD
2-49
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
B30 BUCKETS, CONCRETE

SUBCATEGORY 0.10 GENERAL PURPOSE, MANUAL TRIP
GAR-BRO MANUFACTURING COMPANY

B30GB018 413-G BUCKET, CONCRETE, GENERAL PURPOSE, $3,320 0.72 0.22 0.39 0.02 0.00 4
0.5 CY
1.0 CY
1.5 CY
2.0 CY
3.0 CY
4.0 CY
SUBCATEGORY 0.20 LAYDOWN

B30GB006 425-A BUCKET, CONCRETE, LAYDOWN, 1.0 CY, $26,280 5.94 1.75 3.12 0.19 0.00 26
HEAVY DUTY AIR GATE
HEAVY DUTY AIR GATE
HEAVY DUTY AIR GATE
HEAVY DUTY AIR GATE
2-50
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
B30 GAR-BRO MANUFACTURING COMPANY

(continued)
HEAVY DUTY AIR GATE
SUBCATEGORY 0.30 LOWBOY
CAMLEVER
B30CR001 LB-375 BUCKET, CONCRETE, LOWBOY, 0.38 $4,577 1.06 0.30 0.54 0.03 0.00 2
CY
CY
CY
CY
CY
B30CR009 LXB-150 BUCKET, CONCRETE, LOWBOY, 1.5 $7,954 1.85 0.53 0.94 0.06 0.00 6
CY
CY
CY
CY
CY
2-51
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
SUBCATEGORY 0.40 LOW SLUMP

B30GB011 440-A BUCKET, CONCRETE, LOW SLUMP, 1.0 CY, $17,005 3.96 1.13 2.02 0.12 0.00 20
AIR GATE
AIR GATE
AIR GATE
AIR GATE
AIR GATE
AIR GATE
AIR GATE
B35 BUCKETS, DRAGLINE

SUBCATEGORY 0.10 LIGHT WEIGHT
HENDRIX MANUFACTURING COMPANY, INC.

B35HE001 LS BUCKET, DRAGLINE, 0.75 CY, LIGHT $8,036 1.71 0.51 0.90 0.06 0.00 15
WEIGHT/PERFORATED
WEIGHT/PERFORATED
WEIGHT/PERFORATED
2-52
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
B35 HENDRIX MANUFACTURING COMPANY,

INC. (continued)
WEIGHT/PERFORATED
WEIGHT/PERFORATED
WEIGHT/PERFORATED
WEIGHT/PERFORATED
WEIGHT/PERFORATED
WEIGHT/PERFORATED
WEIGHT/PERFORATED
WEIGHT/PERFORATED
WEIGHT/PERFORATED
WEIGHT/PERFORATED
WEIGHT/PERFORATED
WEIGHT/PERFORATED
WEIGHT/PERFORATED
2-53
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014

INC. (continued)
WEIGHT/PERFORATED
SAUERMAN (NATIONAL OILWELL VARCO)

B35SA001 SC-1050-K BUCKET, DRAGLINE, 1.0 CY, CRESCENT, $58,620 12.50 3.73 6.59 0.43 0.00 15
W/CARRIER
W/CARRIER
W/CARRIER
W/CARRIER
W/CARRIER
W/CARRIER
W/CARRIER
B35SA009 SC-1140-K BUCKET, DRAGLINE, 10.0 CY,CRESCENT, $439,585 93.81 27.99 49.45 3.26 0.00 106
W/CARRIER
B35SA010 SC-1150-K BUCKET, DRAGLINE, 12.0 CY,CRESCENT, $527,552 112.59 33.59 59.35 3.91 0.00 132
W/CARRIER
B35XX001 6-1/2L BUCKET, DRAGLINE, 6.5 CY, LIGHT $31,664 6.75 2.01 3.56 0.23 0.00 94
WEIGHT
WEIGHT
2-54
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014

(continued)
WEIGHT
WEIGHT
B35XX005 11L BUCKET, DRAGLINE, 11.0 CY, LIGHT $50,425 10.75 3.21 5.67 0.37 0.00 148
WEIGHT
B35XX006 13L BUCKET, DRAGLINE, 13.0 CY, LIGHT $62,062 13.24 3.95 6.98 0.46 0.00 178
WEIGHT
SUBCATEGORY 0.20 MEDIUM WEIGHT

B35HE018 TS BUCKET, DRAGLINE, 0.75 CY, MEDIUM $8,679 1.65 0.50 0.87 0.06 0.00 17
WEIGHT
WEIGHT
WEIGHT
WEIGHT
WEIGHT
WEIGHT
WEIGHT
WEIGHT
2-55
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014

INC. (continued)
WEIGHT
WEIGHT
WEIGHT
WEIGHT
WEIGHT
WEIGHT
WEIGHT
WEIGHT
WEIGHT
B35XX007 6-1/2M BUCKET, DRAGLINE, 6.5 CY, MEDIUM $35,826 6.82 2.05 3.58 0.26 0.00 101
WEIGHT
WEIGHT
WEIGHT
2-56
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014

(continued)
WEIGHT
B35XX011 11M BUCKET, DRAGLINE, 11.0 CY, MEDIUM $57,987 11.04 3.32 5.80 0.42 0.00 169
WEIGHT
B35XX012 13M BUCKET, DRAGLINE, 13.0 CY, MEDIUM $73,508 14.00 4.22 7.35 0.54 0.00 211
WEIGHT
SUBCATEGORY 0.30 HEAVY WEIGHT

B35HE035 MH-S BUCKET, DRAGLINE, 2.75 CY, HEAVY $32,370 5.56 1.69 2.91 0.23 0.00 69
WEIGHT
WEIGHT
WEIGHT
WEIGHT
WEIGHT
WEIGHT
WEIGHT
WEIGHT
WEIGHT
2-57
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014

INC. (continued)
WEIGHT
WEIGHT
WEIGHT
WEIGHT
B35XX013 3/4H BUCKET, DRAGLINE, 0.75 CY, HEAVY $9,071 1.57 0.48 0.82 0.07 0.00 20
WEIGHT
B35XX014 1H BUCKET, DRAGLINE, 1.0 CY, HEAVY $10,186 1.75 0.53 0.92 0.07 0.00 23
WEIGHT
B35XX015 1-1/2H BUCKET, DRAGLINE, 1.5 CY, HEAVY $15,141 2.60 0.79 1.36 0.11 0.00 35
WEIGHT
WEIGHT
WEIGHT
WEIGHT
WEIGHT
WEIGHT
2-58
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014

(continued)
WEIGHT
WEIGHT
WEIGHT
C05 CHAIN SAWS

SUBCATEGORY 0.00 CHAIN SAWS
OLYMPYK CHAIN SAWS

C05OL001 941 CHAIN SAW, 16"-18" BAR 2 HP G $367 1.48 0.09 0.17 0.00 0.70 1
C10 COMPACTORS, WALK-BEHIND OR REMOTE CONTROLLER

SUBCATEGORY 0.10 COMPACTORS, RAMMERS / TAMPERS & VIBRATORY PLATES
COMPACTION AMERICA (BOMAG)

C10BO001 BT 60/4 COMPACTOR, RAMMER, TAMPER, 11" X 3 HP G $4,112 3.37 0.52 0.98 0.03 0.91 2
13.2" SHOE, 2,630 LBS IMPACT
C10BO003 BP 10/36-2 COMPACTOR, VIBROPLATE, 14.2" X 22" 4 HP G $1,569 2.25 0.20 0.37 0.01 1.22 2
PLATE, 2,250 LBS IMPACT
C10BO004 BP 18/45-2 COMPACTOR, VIBROPLATE, 17.7" X 22" 6 HP G $1,845 3.09 0.24 0.44 0.02 1.83 2
PLATE, 4,050 LBS IMPACT
2-59
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
C10 COMPACTION AMERICA (BOMAG)

(continued)
C10BO008 BPR 55/65D COMPACTOR, VIBROPLATE, 25.6" X 35.4" 9 HP D-off $16,252 10.86 2.06 3.86 0.13 1.35 10
PLATE, REVERSIBLE, 11,250 LBS
IMPACT
WACKER CORPORATION
C10WC003 DS 70 COMPACTOR, RAMMER, 13" X 13" SHOE, 4 HP D-off $3,940 2.93 0.50 0.94 0.03 0.60 2
3,550 LBS IMPACT
C10WC006 BPU 2540 A COMPACTOR, VIBROPLATE, 19.5" X 25.5" 6 HP G $5,129 4.81 0.65 1.22 0.04 1.68 3
IMPACT
C10WC007 BPU 3545A COMPACTOR, VIBROPLATE, 23.5" X 35.5" 9 HP G $7,825 7.53 0.99 1.86 0.06 2.74 7
IMPACT
C10WC008 DPU 4045H COMPACTOR, VIBROPLATE, 24" X 35.5" 9 HP D-off $14,166 9.66 1.80 3.36 0.12 1.35 7
IMPACT
C10WC015 DPU 7060 COMPACTOR, VIBROPLATE, 25.5" X 42" 14 HP D-off $28,038 18.49 3.56 6.66 0.23 2.10 15
IMPACT
SUBCATEGORY 0.20 ROLLERS, VIBRATORY

C10BO009 BW 55E COMPACTOR, ROLLER, VIBRATORY, 22"W X 4 HP G $8,414 6.00 0.97 1.79 0.07 1.22 3
15.7"DIA, SINGLE SMOOTH DRUM, WALK
BEHIND, 2,273 LBS IMPACT
C10BO015 BW65HS-D COMPACTOR, ROLLER, VIBRATORY, 25.6"W 5 HP D-off $19,687 11.70 2.26 4.18 0.17 0.75 13
X 15.7"DIA, DOUBLE SMOOTH DRUMS,
WALK BEHIND, 2,655 LBS IMPACT
2-60
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
C10 COMPACTION AMERICA (BOMAG)

(continued)
C10BO011 BW 65H COMPACTOR, ROLLER, VIBRATORY, 25.6"W 8 HP D-off $22,124 13.53 2.54 4.70 0.19 1.20 16
C10BO016 BW75S-D COMPACTOR, ROLLER, VIBRATORY, 29.5"W 9 HP D-off $24,661 15.10 2.83 5.24 0.21 1.35 20
C10BO013 BMP851 COMPACTOR, TRENCH ROLLER, 19 HP D-off $50,493 31.02 5.80 10.73 0.43 2.85 45
VIBRATORY, 33.5"W X 19.7"DIA, DOUBLE
TAMPING FOOT DRUMS, WALK BEHIND,
18,000 LBS IMPACT
RAMMAX MACHINERY CO.

C10RX001 P23/16FM COMPACTOR, TRENCH ROLLER, 8 HP D-off $33,001 19.53 3.79 7.01 0.28 1.20 16
VIBRATORY, 23"W X 14.6"DIA, QUAD
PADFOOT DRUMS, WALK BEHIND, 7,875 LBS
IMPACT
C10RX002 P33/24FMR COMPACTOR, TRENCH ROLLER, 14 HP D-off $45,524 27.45 5.23 9.67 0.39 2.10 30
VIBRATORY, 33"W X 21.7"DIA, QUAD
PADFOOT DRUMS, WALK BEHIND, 15,652
LBS IMPACT
C10RX003 P47/40KM COMPACTOR, TRENCH ROLLER, 33 HP D-off $76,071 47.46 8.74 16.17 0.65 4.95 66
VIBRATORY, 47"W X 22"DIA, QUAD
PADFOOT DRUMS, RIDE ON, 21,600 LBS
IMPACT
WACKER CORPORATION
C10WC010 RSS800A COMPACTOR, ROLLER, VIBRATORY, 28"W X 11 HP G $10,037 9.24 1.16 2.13 0.09 3.35 11
22"DIA, SINGLE SMOOTH DRUM, WALK
2-61
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
C10 WACKER CORPORATION (continued)

C10WC017 RD7H COMPACTOR, ROLLER, VIBRATORY,25.5"W 9 HP D-off $13,315 8.84 1.53 2.83 0.11 1.35 16
X 16.5"DIA, DOUBLE SMOOTH DRUM, WALK
C10WC019 RT 56-SC COMPACTOR, ROLLER, VIBRATORY, 22"W X 20 HP D-off $33,120 21.59 3.80 7.04 0.28 3.00 31
20"DIA, DOUBLE SMOOTH DRUM, WALK
BEHIND, 7,000/14,000 LBS IMPACT
C10WC016 RT 82-SC COMPACTOR, TRENCH ROLLER, 20 HP D-off $34,930 22.59 4.01 7.42 0.30 3.00 33
VIBRATORY, 32"W X 20"DIA, DOUBLE
TAMPING FOOT DRUMS, WALK BEHIND,
7,000/14,000 LBS IMPACT
C15 CONCRETE CLEANERS / ABRASIVE BLASTERS

SUBCATEGORY 0.10 WALK BEHIND
US FILTER/BLASTRAC
C15BL001 1-8DEC & BDC- CONCRETE BLASTER CLEANING SYSTEM, 2 HP E $9,940 5.25 1.09 1.99 0.09 0.13 2
1216 WALK BEHIND, 8" PATH (ADD 4 KVA
GENERATOR & BLAST MEDIA COST)
C15BL003 1-10DSG1 & 6- CONCRETE BLASTER CLEANING SYSTEM, 10 HP E $39,233 20.46 4.27 7.85 0.34 0.67 7
54DCG1 WALK BEHIND, 10" PATH (ADD 30 KVA
C15BL004 1-15DSG1 & 6- CONCRETE BLASTER CLEANING SYSTEM, 15 HP E $45,081 23.89 4.90 9.02 0.39 1.00 8
C15BL005 2-20DT & 8- CONCRETE BLASTER CLEANING SYSTEM, 30 HP E $63,269 33.99 6.88 12.65 0.55 2.00 12
2-62
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
EQUIPMENT DEVELOPMENT CO., INC. (EDCO)

C15ED002 CPM-8 CONCRETE GRINDER, WALK BEHIND, 9 HP G $5,151 4.77 0.56 1.03 0.04 2.13 2
TRAFFIC LINE REMOVER, 8'' CUTTING
PATH
C15ED001 TLR-7 CONCRETE GRINDER, WALK BEHIND, 11 HP G $8,513 6.85 0.92 1.70 0.07 2.61 5
TRAFFIC LINE REMOVER, 7'' CUTTING
WIDTH
SUBCATEGORY 0.20 TRUCK/TRAILER MOUNTED
US FILTER/BLASTRAC
C15BL006 2-4800 DH CONCRETE BLASTER, SELF PROPELLED, 350 HP D-off $470,726 170.84 27.25 47.07 3.71 54.97 255
48'' PATH
C15XX001 CONCRETE CLEANER/ABRASIVE BLASTER, 86 HP D-on 180 HP D-off $145,284 68.27 8.29 14.27 1.15 30.75 138
TRUCK MOUNTED, GINDER/BLASTER, 4" -
16" CLEANING PATH WIDTH
C20 CONCRETE BUGGIES

SUBCATEGORY 0.00 CONCRETE BUGGIES
WACKER CORPORATION
C20WC002 WB 16A CONCRETE BUGGY, 16 CF BUCKET, 2,500 13 HP G $12,545 8.29 1.21 2.19 0.11 3.08 13
LBS, WALK & RIDE, 4X2
C20XX001 16G CONCRETE BUGGY, 16 CF BUCKET, 1,500 13 HP G $8,189 6.65 0.79 1.43 0.07 3.08 10
LBS
2-63
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
C25 CONCRETE FINISHERS/SCREEDS/SPREADERS

SUBCATEGORY 0.10 FINISHERS/TROWELS
ALLEN ENGINEERING CORP.

C25AJ015 PRO 900 CONCRETE TROWEL, RIDING, 2 - 36" DIA 20 HP G $12,415 9.68 1.10 1.99 0.10 4.74 8
ROTORS, 8 BLADES
ROTORS, 8 BLADES
ROTORS, 8 BLADES
C25AJ019 SUPER PRO 400 CONCRETE TROWEL, RIDING, 2 - 46" DIA 34 HP G $19,847 16.01 1.76 3.18 0.17 8.05 13
ROTORS, 8 BLADES
STOW MANUFACTURING, INC.

C25ST001 SCT36H80 CONCRETE FINISHER, WALK BEHIND, ROTO 8 HP G $2,784 3.12 0.25 0.45 0.02 1.90 3
TROWEL, 36" DIA ROTOR, 4 BLADES
C25ST002 SCT46H80 CONCRETE FINISHER, WALK BEHIND, ROTO 9 HP G $2,855 3.40 0.25 0.46 0.02 2.13 3
TROWEL, 46" DIA ROTOR, 4 BLADES
WACKER CORPORATION
C25WC002 CT48ADP CONCRETE FINISHER, WALK BEHIND, 8 HP G $3,494 3.37 0.31 0.56 0.03 1.90 3
POWER TROWEL, 48" DIA ROTOR, 4
BLADES
SUBCATEGORY 0.20 VIBRATORY SCREED

C25AJ003 12HED CONCRETE, VIBRATORY SCREED, 22.5' 6 HP G $8,538 4.57 0.76 1.37 0.07 1.42 7
WIDE
2-64
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
C25 ALLEN ENGINEERING CORP. (continued)

C25AJ001 12 HD CONCRETE, VIBRATORY SCREED, 20' 6 HP G $5,035 3.36 0.45 0.81 0.04 1.42 5
WIDE
WIDE
WIDE
C25AJ006 12HED CONCRETE, VIBRATORY SCREED, 50' 11 HP G $12,168 7.17 1.08 1.95 0.10 2.61 12
WIDE
C25AJ007 12HED CONCRETE, VIBRATORY SCREED, 55' 11 HP G $12,852 7.41 1.14 2.06 0.11 2.61 13
WIDE
SUBCATEGORY 0.25 VIBRATORY LASER SCREED
SOMERO ENTERPRISES, INC.

C25SV003 S-100 CONCRETE, VIBRATORY LASER SCREED, 8' 30 HP D-off $157,509 31.95 8.14 13.63 1.32 3.25 72
WIDE X 12' BOOM
C25SV002 SXP CONCRETE, VIBRATORY LASER SCREED, 8' 65 HP D-off $315,003 64.48 16.32 27.38 2.63 7.03 126
(VERSATILE) WIDE X 20' BOOM
C25SV001 SXP CONCRETE, VIBRATORY LASER SCREED, 65 HP D-off $335,070 68.08 17.35 29.09 2.80 7.03 151
(PRODUCTIVE) 12' WIDE X 20' BOOM
SUBCATEGORY 0.30 MATERIAL/TOPPING SPREADERS

C25AJ008 SP23H CONCRETE, MATERIAL/TOPPING 6 HP G $17,214 4.51 0.90 1.51 0.14 1.22 11
SPREADER, 12.5' WIDE
SPREADER, 20' WIDE
2-65
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
C25 ALLEN ENGINEERING CORP. (continued)

SPREADER, 30' WIDE
SPREADER, 40' WIDE
SPREADER, 50' WIDE
SPREADER, 60' WIDE
C35 CONCRETE GUNITERS / SHOTCRETERS

SUBCATEGORY 0.00 CONCRETE GUNITERS / SHOTCRETERS
AIRPLACO EQUIPMENT CO., INC.

C35AF002 C-10SL CONCRETE GUNITER/SHOTCRETER, 9 CFM A $16,611 6.25 1.01 1.74 0.14 0.00 6
DRY/SEMI-WET, HOPPER/PUMP/SPRAY, 12
CY/HR, 2" HOSE & 1 GUN (ADD 600 CFM
COMPRESSOR)
C35AF004 634D Mix CONCRETE GUNITER/SHOTCRETER, DRY 30 HP D-off $47,064 18.30 2.88 4.98 0.39 3.77 45
Elevator BATCH MIXER, 13 CY/HR, W/FEEDER,
TRAILER MTD (ADD SHOTCRETE
MACHINE)
C35AF005 734LBD Mix CONCRETE GUNITER/SHOTCRETER, DRY 54 HP D-off $68,860 27.20 4.18 7.22 0.57 6.78 81
Elevator BATCH MIXER, W/20 CY/HR ELEVATOR
FEEDER/ 45 CF SAND HOPPER/ 4 CF
CEMENT HOPPER/ & PREDAMPENING
SPRAY BAR, TRAILER MTD (ADD
SHOTCRETE MACHINE)
2-66
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
ALLENTOWN EQUIPMENT
C35AL003 GRH-610 CONCRETE GUNITER/SHOTCRETER, 5 HP E $16,817 4.90 0.93 1.58 0.14 0.36 11
ROTARY GUN ROTARY PUMP, WET/DRY, 1 - 6 CY/HR,
W/HOPPER/ 100' - 1.5" DIA HOSE/ & NOZZLE,
CART MTD, (ADD 250 - 600 CFM
COMPRESSOR)
C35AL013 AG-15 CONCRETE GUNITER/SHOTCRETER, 9 CFM A $14,214 3.98 0.83 1.41 0.12 0.00 15
AUTOMATIC ROTARY PUMP, WET/DRY, 3 - 15 CY/HR,
GUN W/HOPPER/ 100' - 1.5" DIA HOSE/ & NOZZLE
(ADD 300 - 900 CFM COMPRESSOR)
C35AL008 N-2 CONCRETE GUNITER/SHOTCRETER, DRY 9 CFM A $27,531 7.39 1.71 2.95 0.23 0.00 13
PNEUMATIC MIX, 2 - 8 CY/HR, W/2 PRESSURIZED TANKS/
GUN 100' - 1.5" DIA HOSE/ & NOZZLE (ADD 200 -
900 CFM COMPRESSOR)
C35AL002 R-900 BATCH CONCRETE GUNITER/SHOTCRETER, DRY 30 HP D-off $47,101 17.20 2.81 4.83 0.39 3.77 47
MIX RIG BATCH MIXER, 10 TON/HR, W/ELEVATOR
FEEDER/ 20 CF CEMENT HOPPER/ 8 CF
MIXER/ & PREDAMPENING SPRAY BAR,
TRAILER MTD (ADD SHOTCRETE MACHINE
OR ROTARY PUMP)
C35AL014 POWER CONCRETE GUNITER/SHOTCRETER, 61 HP D-off $72,276 27.65 4.44 7.68 0.60 7.66 30
CRETER 10 GROUT/MUD JACK/ SHOTCRETE, 10 CY/HR,
2,085 PSI, W/30 GAL HOPPER/ 74 GAL
MIXER, TRAILER MTD (ADD 3" HOSE
LINE)
ALIVA LTD.
C35AV008 AL 246 CONCRETE GUNITER/SHOTCRETER, 7 HP E $29,686 10.37 1.83 3.18 0.24 0.50 9
DRY/SEMI-WET, 1.4 - 2.3 CY/HR, W/1 GAL
HOPPER/ ROTARY PUMP/ 100' - 1.5" DIA
HOSE/ NOZZLE/ & AIR COMPRESSOR
2-67
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
C35 ALIVA LTD. (continued)

DRY/SEMI-WET, 5 - 10 CY/HR, W/4.2 GAL
WET/DRY, 9 - 13 CY/HR, W/4.2 GAL HOPPER/
ROTARY PUMP/ 100' - 2.36" DIA HOSE/
NOZZLE/ & AIR COMPRESSOR
WET/DRY, 11 - 27.5 CY/HR, W/6.6 GAL
SHOTCRETE HYDRAULIC SPRAYER ARM,
25.6 ' HIGH (ADD TRUCK OR SMALL
TRAILER & SHOTCRETE UNIT)
C35AV012 AL 307 CONCRETE GUNITERS / SHOTCRETERS, 20 HP E $154,340 44.33 9.54 16.54 1.27 1.43 68
SHOTCRETE HYDRAULIC SPRAYER ARM,
52.5' HIGH (ADD TRUCK OR SMALL TRAILER
& SHOTCRETE UNIT)
C40 CONCRETE MIXING UNITS

SUBCATEGORY 0.00 CONCRETE MIXING UNITS
CEMEN TECH
C40CC001 SCD2-50H CONCRETE MIXERS, STATIONARY 10 HP E $32,620 12.28 2.88 5.22 0.27 0.67 23
CONCRETE DISPENSER, 15 CY/HR, 2 - 4.5
CY MATERIAL CAPACITY
2-68
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
MULTIQUIP, INC.
C40MU001 WM 70SH8 CONCRETE MIXERS, MIXER, 8 HP G $3,771 3.42 0.31 0.55 0.03 1.90 8
PLASTER/MORTAR, 7 CF, TRAILER
MTD
C40MU002 WM 120SHH CONCRETE MIXERS, MIXER, 13 HP G $7,694 6.12 0.65 1.18 0.06 3.08 11
PLASTER/MORTAR, 12 CF, TRAILER
MTD
C40MU003 MC 64SH8 CONCRETE MIXERS, MIXER, CONCRETE, 6 8 HP G $3,725 3.41 0.31 0.55 0.03 1.90 7
CF, TRAILER MTD
C40MU004 MC 94SH8 CONCRETE MIXERS, MIXER, CONCRETE, 9 8 HP G $4,284 3.61 0.36 0.64 0.04 1.90 8
CF, TRAILER MTD

C40ST001 CMS44E CONCRETE MIXERS, MIXER, CONCRETE, 4 1 HP E $2,342 1.03 0.19 0.33 0.02 0.03 5
CF, TRAILER MTD
C40ST002 CMS44H CONCRETE MIXERS, MIXER, CONCRETE, 4 6 HP G $2,566 2.33 0.20 0.36 0.02 1.30 5
CF, TRAILER MTD
CF, TRAILER MTD
CF, TRAILER MTD
C40XX001 8E CONCRETE MIXERS, MIXER, 2 HP E $2,954 1.41 0.26 0.47 0.02 0.13 7
PLASTER/MORTAR, 8 CF, ELECTRIC,
PORTABLE
C40XX002 8G CONCRETE MIXERS, MIXER, 7 HP G $3,174 2.99 0.29 0.51 0.03 1.66 7
PLASTER/MORTAR, 8 CF, GAS,
PORTABLE
2-69
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
C40 NO SPECIFIC MANUFACTURER

(continued)
PORTABLE
PORTABLE
PORTABLE
PORTABLE
PORTABLE
C45 CONCRETE PAVING MACHINES

SUBCATEGORY 0.00 CONCRETE PAVING MACHINES
GOMACO CORPORATION
C45GO026 C-450 CONCRETE PAVING MACHINES, CYLINDER 36 HP G $60,431 29.95 4.52 8.06 0.49 9.20 64
FINISHER, SINGLE DRUM, FINISHING WIDTH
9'-137'
C45GO027 C-650-F CONCRETE PAVING MACHINES, CYLINDER 50 HP D-off $76,735 31.78 5.75 10.23 0.63 6.28 91
FINISHER, DOUBLE DRUM, FINISHING
WIDTH 19'-51'
C45GO028 C-650-S CONCRETE PAVING MACHINES, CYLINDER 50 HP D-off $122,242 46.45 9.15 16.30 1.00 6.28 126
WIDTH 19'-51'
2-70
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
C45 GOMACO CORPORATION (continued)

C45GO029 C-750 CONCRETE PAVING MACHINES, CYLINDER 36 HP G $81,209 36.65 6.08 10.83 0.66 9.20 91
WIDTH 8'-156'
C45GO013 GT-3200 CONCRETE PAVING MACHINES, 92 HP D-off $140,131 58.13 10.49 18.68 1.15 11.56 130
CURB/GUTTER SLIPFORM PAVER,
CRAWLER, 3-TRACK, 36" WIDE
MOLD/FORM
C45GO010 COMMANDER II CONCRETE PAVING MACHINES, 92 HP D-off $168,561 67.29 12.62 22.47 1.38 11.56 200
/GT6200 CURB/GUTTER SLIPFORM PAVER,
CRAWLER, 2-TRACK, 36'' WIDE
MOLD/FORM
C45GO014 GT-3600 CONCRETE PAVING MACHINES, 98 HP D-off $192,963 76.00 14.45 25.73 1.58 12.31 210
MOLD/FORM
C45GO011 COMMANDER CONCRETE PAVING MACHINES, 185 HP D-off $259,911 109.83 19.45 34.65 2.12 23.24 300
III/GT6300 CURB/GUTTER SLIPFORM PAVER,
MOLD/FORM
C45GO012 COMMANDER III CONCRETE PAVING MACHINES, 169 HP D-off $348,760 136.22 26.10 46.50 2.85 21.23 369
CRAWLER , 4-TRACK, 36'' WIDE
MOLD/FORM
C45GO016 GP-2600 CONCRETE PAVING MACHINES, SLIPFORM 230 HP D-off $382,443 155.68 28.63 50.99 3.13 28.90 750
PAVER, CRAWLER, 2-TRACK, 24'-32' PAVING
WIDTH
C45GO018 GHP-2800 CONCRETE PAVING MACHINES, SLIPFORM 335 HP D-off $477,062 200.97 35.71 63.61 3.90 42.09 700
WIDTH
2-71
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
C45 GOMACO CORPORATION (continued)

C45GO020 GP-4000 CONCRETE PAVING MACHINES, SLIPFORM 450 HP D-off $570,613 247.32 42.70 76.08 4.66 56.54 880
WIDTH
C45GO031 9500 CONCRETE PAVING MACHINES, 385 HP D-off $463,415 203.61 34.69 61.79 3.79 48.37 729
TRIMMER/PLACER, W/16'-8'' TRIMMER
HEAD
MILLER SPREADER CO.

C45MJ001 MC 650 CONCRETE PAVING MACHINES, CURB 15 HP G $8,773 7.20 0.66 1.17 0.07 3.84 8
BUILDER, SLIPFORM PAVER, 6.1 CF
HOPPER 6" AUGER
M-B-W, INC.
C45MW00 C101 CONCRETE PAVING MACHINES, CURB 26 HP D-off $50,822 20.00 3.78 6.71 0.42 3.27 27
ONLY SLIPFORM PAVER, RUBBER TIRED,
12"
C45MW00 CG200 CONCRETE PAVING MACHINES, 26 HP D-off $64,543 24.42 4.79 8.51 0.53 3.27 34
CURB/GUTTER SLIPFORM PAVER, RUBBER
TIRED, 48"
C55 CONCRETE PUMPS

SUBCATEGORY 0.00 CONCRETE PUMPS
MAYCO PUMP - MULTIQUIP INC.

C55M3001 C-30HDG CONCRETE PUMP, 25 CY/HR, SINGLE, 46 HP G $24,873 18.79 1.55 2.74 0.18 10.90 27
TRAILER MTD
C55M3002 LS-400 CONCRETE PUMP, 45 CY/HR, SINGLE, 60 HP D-off $56,758 22.62 3.62 6.39 0.42 7.12 42
TRAILER MTD
2-72
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
C55 MAYCO PUMP - MULTIQUIP INC.

(continued)
C55M3003 LS-600 CONCRETE PUMP, 70 CY/HR, SINGLE, 106 HP D-off $64,832 30.82 4.13 7.29 0.48 12.58 47
TRAILER MTD
OLIN ENGINEERING, INC.

C55OE006 10 22 CONCRETE PUMP, 22 CY/HR,TRAILER MTD 74 HP D-off $54,022 23.74 3.41 6.02 0.40 8.78 44
(OPEN LOOP HYDRAULIC SYSTEM)
C55OE009 20 80 CONCRETE PUMP, 76 CY/HR, TRAILER MTD 127 HP D-off $102,111 43.17 6.45 11.38 0.76 15.07 72
TANDEM (CLOSED LOOP HYDRAULIC
SYSTEM)
C55OE011 15 95 CONCRETE PUMP, 100 CY/HR, TRAILER 181 HP D-off $74,708 43.28 4.70 8.30 0.55 21.48 70
MTD TANDEM (OPEN LOOP HYDRAULIC
SYSTEM)
C55OE012 20 100 CONCRETE PUMP, 100 CY/HR, TRAILER 181 HP D-off $119,997 54.96 7.59 13.39 0.89 21.48 81
MTD TANDEM (CLOSED LOOP HYDRAULIC
SYSTEM)
C55OE001 4Z 26X CONCRETE PUMP, PUMP & BOOM, 130 $287,444 74.14 18.30 32.34 2.13 0.00 100
CY/HR, REACH: 72' HORIZONTAL / 85'
VERTICAL (ADD 50,000 GVW TRUCK)
C55OE002 4Z 36X CONCRETE PUMP, PUMP & BOOM, 182 $369,270 95.24 23.51 41.54 2.74 0.00 100
C55OE003 5RZ 47I CONCRETE PUMP, PUMP & BOOM, 182 $562,677 145.12 35.82 63.30 4.17 0.00 100
SCHWING AMERICA INC.

C55SC001 SP750-18 CONCRETE PUMP, 70 CY/HR, 1,100 PSI, 80 HP D-off $82,733 31.94 5.24 9.25 0.61 9.49 69
TRAILER MTD
2-73
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
C55 SCHWING AMERICA INC. (continued)

C55SC002 SP2800 CONCRETE PUMP, 76 CY/HR, 1,565 PSI, 197 HP D-off $143,955 63.22 9.07 16.00 1.07 23.38 115
TRAILER MTD
C55SC005 S 28X CONCRETE PUMP, 117 CY/HR, 75' BOOM, 210 HP D-on $478,499 155.62 30.13 53.16 3.55 28.92 359
TRUCK MTD
C55SC006 KVM 32XG CONCRETE PUMP, 117 CY/HR, 92' BOOM, 210 HP D-on $515,809 165.24 32.50 57.36 3.82 28.92 470
TRUCK MTD
C60 CONCRETE SAWS (Add cost for sawblade wear)

SUBCATEGORY 0.00 CONCRETE SAWS (Add cost for sawblade wear)
HUSQVARNA CONSTRUCTION PRODUCTS

C60HG008 K760 CONCRETE SAW, 5.00" DEPTH, MANUAL, 14" 2 HP G $1,021 1.04 0.09 0.15 0.01 0.61 1
BLADE (ADD COST FOR SAWBLADE WEAR
& WATER)
C60HG010 FS 400 CONCRETE SAW, 6.5" DEPTH, WALK 11 HP G $1,990 4.50 0.17 0.30 0.02 3.35 2
BEHIND, 18" BLADE (ADD COST FOR
SAWBLADE WEAR & WATER)
C60HG015 FS 520 CONCRETE SAW, 7.625" DEPTH, SELF 20 HP G $6,066 9.01 0.51 0.91 0.05 6.09 5
PROPELLED, 20" BLADE (ADD COST FOR
C60HG020 FS 4600 G 20 CONCRETE SAW, 12" DEPTH, SELF- 48 HP G $20,977 23.81 1.74 3.15 0.16 14.62 12
C60HG021 FS 4600 G 30 CONCRETE SAW, 12" DEPTH, SELF 48 HP G $25,338 25.30 2.10 3.80 0.20 14.62 12
C60HG023 FS 3500 E 30 CONCRETE SAW, 11.5" DEPTH, SELF 30 HP E $14,876 8.90 1.23 2.23 0.11 2.57 9
2-74
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
C60 HUSQVARNA CONSTRUCTION

PRODUCTS (continued)
C60HG024 FS 4600 G 26 CONCRETE SAW, 12" DEPTH, SELF- 48 HP G $25,281 25.28 2.10 3.79 0.20 14.62 12
C60HG025 FS 309 G 14 CONCRETE SAW, 4.625" DEPTH, MANUAL, 9 HP G $1,602 3.66 0.13 0.24 0.01 2.74 2
14" BLADE (ADD COST FOR SAWBLADE
WEAR & WATER)
C60HG026 FS 513 G 18 CONCRETE SAW, 7.5" DEPTH, SELF- 13 HP G $3,988 5.87 0.33 0.60 0.03 3.96 4
C60HG011 FS 6600 D 20 CONCRETE SAW, 6.5" DEPTH, SELF 66 HP D-off $26,622 20.63 2.21 3.99 0.21 9.90 19
C60HG014 FS 3500 E 26 CONCRETE SAW, 10.625" DEPTH, SELF 30 HP E $14,731 8.85 1.22 2.21 0.11 2.57 9
BOART LONGYEAR COMPANY

C60LY005 FS 13B CONCRETE SAW, 7.00" DEPTH, WALK 13 HP G $3,319 5.65 0.28 0.50 0.03 3.96 2
BEHIND(ADD COST FOR SAWBLADE WEAR
& WATER)
2-75
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
C60 BOART LONGYEAR COMPANY

(continued)
C60LY001 360-10AP CONCRETE SAW, RAIL SAW, 15.50" DEPTH, 10 HP G $29,025 13.38 2.40 4.35 0.22 3.05 2
WALL (ADD COMPRESSOR & COST FOR
C60LY002 360-35HM CONCRETE SAW, RAIL SAW, 24.50" DEPTH, 35 HP G $42,932 26.80 3.55 6.44 0.33 10.66 2
WALL(ADD COST FOR SAWBLADE WEAR &
WATER)
C60LY011 WR-400 CONCRETE SAW, WIRE SAW SYSTEM, 32 HP D-off $82,895 33.91 6.86 12.43 0.64 4.80 15
HEAVY DUTY (ADD COST FOR SAW WIRE
WEAR & WATER)
C65 CONCRETE VIBRATORS

SUBCATEGORY 0.00 CONCRETE VIBRATORS

C65ST007 SV-1 115V CONCRETE VIBRATOR, 1.375" HEAD, 21' 1 HP E $1,090 1.11 0.14 0.25 0.01 0.06 1
SHAFT (ADD 2KV GENERATOR)
C65ST013 G55H CONCRETE VIBRATOR, 2.325" HEAD, 21' 6 HP G $2,486 3.70 0.30 0.56 0.02 1.22 2
SHAFT, W/GAS MOTOR ON CART
WACKER CORPORATION
C65WC005 A 5000 CONCRETE VIBRATOR, 1.75" HEAD, 13' 5 HP G $2,275 3.37 0.28 0.51 0.02 1.11 1
SHAFT, W/GAS MOTOR ON CART
2-76
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
C65 WACKER CORPORATION (continued)

C65WC004 M 3000 CONCRETE VIBRATOR, 1.75" HEAD, 13' 3 HP E $1,197 1.53 0.15 0.27 0.01 0.19 1
SHAFT, HI-FREQ INTERNAL (ADD 2KV
GENERATOR)
C65WC003 IREN 57 CONCRETE VIBRATOR, 2.50" HEAD, 16.5' 2 HP E $1,862 2.05 0.23 0.42 0.02 0.12 1
SHAFT, HI-FREQ INTERNAL (ADD 2KV
GENERATOR)
C75 CRANES, HYDRAULIC, SELF-PROPELLED

SUBCATEGORY 0.00 CRANES, HYDRAULIC, SELF-PROPELLED
BRODERSON MANUFACTURING CORPORATION

C75BD007 IC-20-1F CRANES, HYDRAULIC, SELF-PROPELLED, 38 HP G $63,722 19.45 2.36 3.80 0.46 9.72 63
YARD, 2.5 TON, 15' BOOM, 4X2
C75BD008 IC-35-2C CRANES, HYDRAULIC, SELF-PROPELLED, 42 HP G $84,763 23.34 3.16 5.08 0.62 10.74 78
YARD, 4.0 TON, 19.2' BOOM, 4X2
C75BD004 IC-35-2C CRANES, HYDRAULIC, SELF-PROPELLED, 42 HP G $88,293 23.78 3.29 5.30 0.64 10.74 79
YARD, 4.0 TON, 19' BOOM, 4X2, NON-
ROTATING OPERATOR'S CAB
C75BD009 IC-80-3G CRANES, HYDRAULIC, SELF-PROPELLED, 69 HP G $114,086 35.21 4.22 6.77 0.83 17.64 172
C75BD005 IC-80-1G CRANES, HYDRAULIC, SELF-PROPELLED, 69 HP G $110,472 34.74 4.08 6.55 0.80 17.64 163
C75BD006 IC-200-3F CRANES, HYDRAULIC, SELF-PROPELLED, 110 HP G $161,278 53.50 5.94 9.53 1.17 28.12 308
C75BD010 IC-250-3A CRANES, HYDRAULIC, SELF-PROPELLED, 85 HP D-off $190,458 37.32 7.03 11.30 1.38 10.68 384
2-77
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
C75 BRODERSON MANUFACTURING

CORPORATION (continued)
C75BD011 RT-300-2B CRANES, HYDRAULIC, SELF-PROPELLED, 130 HP D-off $253,573 52.87 9.38 15.08 1.84 16.33 473
YARD, 15.0 TON, 60' BOOM, 4X4, 20'0"
OFFSET
GROVE CRANES (MANITOWOC)

C75GV029 YB4411 CRANES, HYDRAULIC, SELF-PROPELLED, 80 HP G $174,605 46.26 6.49 10.44 1.27 20.45 175
C75GV030 YB5515 CRANES, HYDRAULIC, SELF-PROPELLED, 100 HP G $265,071 63.62 9.90 15.96 1.92 25.57 326
YARD, 15 TON, 41' BOOM, 4X4, NON-
C75GV023 RT530E-2 CRANES, HYDRAULIC, SELF-PROPELLED, 160 HP D-off $429,181 82.89 15.77 25.32 3.11 20.10 580
ROUGH TERRAIN, 30 TON, 95' BOOM,
4X4
C75GV024 RT640E CRANES, HYDRAULIC, SELF-PROPELLED, 173 HP D-off $564,639 103.86 20.66 33.11 4.10 21.74 650
ROUGH TERRAIN, 40 TON, 105' BOOM
4X4
C75GV016 RT9130E-2 CRANES, HYDRAULIC, SELF-PROPELLED, 300 HP D-off $1,479,827 252.82 54.19 86.90 10.74 37.69 1,364
ROUGH TERRAIN, 130 TON, 160' BOOM, 4X4,
W/HOOK BLOCK & BALL
C75GV031 RT765E CRANES, HYDRAULIC, SELF-PROPELLED, 240 HP D-off $691,353 136.79 24.98 39.91 5.02 30.15 934
W/HOOK BLOCK & BALL
C75GV032 RT880E CRANES, HYDRAULIC, SELF-PROPELLED, 275 HP D-off $836,496 161.97 30.32 48.49 6.07 34.55 1,093
W/HOOK BLOCK & BALL
2-78
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
TADANO AMERICA CORPORATION

C75TD009 GR-350XL-2 CRANES, HYDRAULIC, SELF-PROPELLED, 180 HP D-off $358,263 71.78 13.48 21.75 2.60 22.62 537
ROUGH TERRAIN, 35
TON, 112' BOOM, 4X4
ROUGH TERRAIN, 55TON, 175' BOOM,
4X4
4X4
TEREX CORPORATION
C75TE001 RT230 CRANES, HYDRAULIC, SELF-PROPELLED, 130 HP D-off $379,288 70.42 13.99 22.48 2.75 16.33 563
4X4
C75TE002 RT335/40 CRANES, HYDRAULIC, SELF-PROPELLED, 152 HP D-off $521,828 92.98 19.26 30.94 3.79 19.10 634
4X4
C80 CRANES, HYDRAULIC, TRUCK MOUNTED

SUBCATEGORY 0.01 UNDER 26 TON
TEREX CORPORATION
C80TE008 CD225 CRANES, HYDRAULIC, TRUCK MTD, ROUGH 130 HP D-off $302,371 55.32 11.00 17.62 2.19 14.06 525
TERRAIN, 25 TON, 72' BOOM, 4X4
C80XX001 1700 CRANES, HYDRAULIC, TRUCK MTD, BOOM 245 HP D-off $152,303 49.10 5.54 8.86 1.11 26.51 330
TRUCK, 17 TON, 80' BOOM, 4X2
2-79
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
C80 NO SPECIFIC MANUFACTURER

(continued)
C80XX002 2300 CRANES, HYDRAULIC, TRUCK MTD, BOOM 300 HP D-off $202,311 62.30 7.32 11.69 1.47 32.46 600
TRUCK, 23.5 TON, 102' BOOM, 6X2
SUBCATEGORY 0.02 26 TON THRU 65 TON

C80GV006 TMS-700E CRANES, HYDRAULIC, TRUCK MTD, 50 TON, 400 HP D-off $848,657 140.36 28.46 44.69 6.11 43.28 771
110' BOOM, 8X4
C80GV029 TMS750E CRANES, HYDRAULIC, TRUCK MTD, 50 TON, 450 HP D-off $887,359 152.12 29.54 46.30 6.39 48.69 947
110' BOOM, 8X4X4
C80GV033 GMK3055 CRANES, HYDRAULIC, TRUCK MTD, ALL 355 HP D-off $1,041,325 161.59 34.68 54.36 7.50 38.41 782
TERRAIN, 60 TON, 141' BOOM, 6X4X6
110' BOOM, 8X4X4
LINK-BELT CONSTRUCTION EQUIPMENT CO.

C80LB009 HTC-8640 SL CRANES, HYDRAULIC, TRUCK MTD, 40 TON, 365 HP D-off $616,547 111.23 20.64 32.39 4.44 39.49 575
105' BOOM, 6X4X2
C80LB011 HTC-8660 II CRANES, HYDRAULIC, TRUCK MTD, 60 TON, 365 HP D-off $629,290 113.88 20.88 32.69 4.53 39.49 831
110' BOOM, 8X4X4
TEREX CORPORATION
C80TE002 T335/40 CRANES, HYDRAULIC, TRUCK MTD, ALL 250 HP D-off $384,108 73.15 12.70 19.86 2.77 27.05 493
C80TE003 T 500 CRANES, HYDRAULIC, TRUCK MTD, ALL 370 HP D-off $512,711 102.27 16.91 26.43 3.69 40.03 806
2-80
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
SUBCATEGORY 0.03 66 TON THRU 125 TON

C80GV034 GMK4100B CRANES, HYDRAULIC, TRUCK MTD, ALL 402 HP D-off $1,495,192 208.14 45.56 69.75 10.68 43.49 940
TERRAIN, 100 TON, 167' BOOM, 8X6X8
128' BOOM, 8X4X4

C80TD001 ATF-650XL CRANES, HYDRAULIC, TRUCK MTD, ALL 121 HP D-off 349 HP D-on $779,493 106.53 23.41 35.67 5.57 20.16 1,090
C80TD002 ATF-1000XL CRANES, HYDRAULIC, TRUCK MTD, ALL 158 HP D-off 375 HP D-on $971,839 130.93 29.32 44.75 6.94 24.68 1,070
C80TD003 ATF-90G-4 CRANES, HYDRAULIC, TRUCK MTD, ALL 158 HP D-off 375 HP D-on $1,099,406 139.44 33.81 51.92 7.85 24.68 1,070
SUBCATEGORY 0.04 OVER 125 TON

C80GV016 GMK 6350 CRANES, HYDRAULIC, TRUCK MTD, ALL 255 HP D-off 563 HP D-on $3,033,501 354.81 85.24 127.38 21.55 38.99 1,425

C80TD004 ATF-130G-5 CRANES, HYDRAULIC, TRUCK MTD, ALL 533 HP D-off 503 HP D-on $1,386,043 210.93 39.31 58.91 9.85 67.86 1,330
C80TD005 ATF-1500XL CRANES, HYDRAULIC, TRUCK MTD, ALL 533 HP D-off 503 HP D-on $1,166,604 195.32 32.44 48.29 8.29 67.86 1,330
2-81
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
C85 CRANES, MECHANICAL, LATTICE BOOM, CRAWLER MOUNTED

SUBCATEGORY 0.12 DRAGLINE, CLAMSHELL, OVER 1.0 CY THRU 2.5 CY

C85LB019 138 HSL CRANES, MECHANICAL, LATTICE BOOM, 284 HP D-off $867,917 128.74 28.17 43.40 6.47 25.77 1,390
CRAWLER, DRAGLINE/CLAMSHELL, 80 TON,
100' BOOM (ADD BUCKET)
TEREX CORPORATION
C85TE001 5220 CRANES, MECHANICAL, LATTICE BOOM, 150 HP D-off $693,132 94.82 22.50 34.66 5.17 13.61 831
C85TE002 7225 CRANES, MECHANICAL, LATTICE BOOM, 250 HP D-off $964,430 136.22 31.30 48.22 7.19 22.69 1,259
SUBCATEGORY 0.13 DRAGLINE, CLAMSHELL, OVER 2.5 CY THRU 5.0 CY

C85LB021 238 HYLAB 5 CRANES, MECHANICAL, LATTICE BOOM, 284 HP D-off $1,376,074 177.25 40.78 61.16 10.20 25.77 3,357
CRAWLER, DRAGLINE/CLAMSHELL, 150
TON, 100' BOOM (ADD BUCKET)
MANITOWOC ENGINEERING CO.

C85MA002 777 CRANES, MECHANICAL, LATTICE BOOM, 340 HP D-off $1,503,226 196.58 44.55 66.81 11.14 30.85 3,815
CRAWLER, DRAGLINE/CLAMSHELL, 5.0 CY,
2-82
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
TEREX CORPORATION
C85TE003 9225 CRANES, MECHANICAL, LATTICE BOOM, 335 HP D-off $1,216,665 165.05 36.06 54.07 9.02 30.40 2,482
CRAWLER, DRAGLINE/CLAMSHELL, 150
TON, 100' BOOM (ADD BUCKET)
SUBCATEGORY 0.14 DRAGLINE, CLAMSHELL, OVER 5.0 CY

SUBCATEGORY 0.22 LIFTING, 26 TON THRU 50 TON

C85LB024 108 HYLAB 5 CRANES, MECHANICAL, LATTICE BOOM, 197 HP D-off $624,487 74.39 18.51 27.75 4.63 13.06 968
CRAWLER, 50 TON, 70' BOOM,
LIFTING
SUBCATEGORY 0.23 LIFTING, 51 TON THRU 150 TON
KOBELCO AMERICA INC.

C85KC009 CK1100 CRANES, MECHANICAL, LATTICE BOOM, 285 HP D-off $765,527 93.46 21.71 32.53 5.44 18.90 2,148
LIFTING
C85KC010 CK1600 CRANES, MECHANICAL, LATTICE BOOM, 363 HP D-off $1,236,205 143.87 35.05 52.54 8.78 24.07 3,338
LIFTING
C85KC005 CK850 CRANES, MECHANICAL, LATTICE BOOM, 213 HP D-off $649,157 77.16 18.41 27.59 4.61 14.12 1,729
LIFTING
2-83
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014

C85LB001 138 HSL CRANES, MECHANICAL, LATTICE BOOM, 248 HP D-off $794,338 93.50 22.52 33.76 5.64 16.44 1,464
CRAWLER, 80 TON, 40' TUBULAR BOOM,
LIFTING
C85LB014 218 HSL CRANES, MECHANICAL, LATTICE BOOM, 284 HP D-off $1,037,315 119.23 29.42 44.09 7.37 18.83 1,790
LIFTING
LIFTING

LIFTING
LIFTING
LIFTING
TEREX CORPORATION
C85TE008 HC 80 CRANES, MECHANICAL, LATTICE BOOM, 184 HP D-off $729,012 82.65 20.67 30.98 5.18 12.20 1,430
LIFTING
C85TE009 HC 110 CRANES, MECHANICAL, LATTICE BOOM, 230 HP D-off $898,840 102.14 25.49 38.20 6.39 15.25 1,911
LIFTING
2-84
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
C85 TEREX CORPORATION (continued)

C85TE010 HC 125 CRANES, MECHANICAL, LATTICE BOOM, 240 HP D-off $1,192,209 130.75 33.81 50.67 8.47 15.91 2,128
LIFTING
SUBCATEGORY 0.24 LIFTING, OVER 150 TON

LIFTING
LIFTING

LIFTING

LIFTING
LIFTING
TEREX CORPORATION
C85TE011 HC 210 CRANES, MECHANICAL, LATTICE BOOM, 315 HP D-off $1,760,865 184.85 46.47 68.03 12.45 20.89 3,708
LIFTING
2-85
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
C90 CRANES, MECHANICAL, LATTICE BOOM, TRUCK MOUNTED

SUBCATEGORY 0.04 OVER 125 TON

C90LB001 HC-238H II CRANES, MECHANICAL, LATTICE BOOM, 200 HP D-off 445 HP D-on $1,622,296 198.65 43.73 63.54 11.96 25.76 1,913
TRUCK MTD, 150 TON, 260' BOOM,
8X4
C90LB003 HC-278 H II CRANES, MECHANICAL, LATTICE BOOM, 445 HP D-off 445 HP D-on $3,000,362 360.59 81.12 117.98 22.13 46.28 3,385
TRUCK MTD, 300 TON, 330' BOOM,
12X6
C95 CRANES, TOWER

SUBCATEGORY 0.00 CRANES, TOWER
PECCO AND WOLFF TOWER CRANES (MORROW)

C95AP004 SK200 TOWER CRANE 3.4 TON @ 181' RADIUS 42.6' 128 HP E $557,765 73.26 16.53 24.79 4.13 7.90 970
HEIGHT (ADD 95KW GENERATOR & T-
SECTION)
C95AP005 S16-35 TOWER TOWER CRANE OPTION, 1.1' T-TRANSITION $17,559 1.80 0.52 0.78 0.13 0.00 16
SECTION S35 -S16 (ADD SK 140 - SK 225 TOWER
CRANE)
C95AP006 S35 TOWER TOWER CRANE OPTION, 19.33' TOWER $32,844 3.36 0.97 1.46 0.24 0.00 89
SECTION SECTION (ADD TO SK 140 - SK 400 TOWER
CRANE)
C95AP007 SK400 TOWER CRANE, 3.3 TON @ 245' RADIUS, 213 HP E $881,560 115.49 26.12 39.18 6.53 13.15 1,783
56.7' HEIGHT (ADD 160 KW GENERATOR & T-
SECTION)
2-86
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
C95 PECCO AND WOLFF TOWER CRANES

(MORROW) (continued)
C95AP008 S35 CLIMBING TOWER CRANE OPTION, 29.2' CLIMBING $133,871 14.20 3.97 5.95 0.99 0.00 248
UNIT UNIT (ADD TO SK 200 - SK 400 TOWER
CRANE)
C95AP009 S35-60 TOWER TOWER CRANE OPTION, 19.4' T- $44,385 4.54 1.32 1.97 0.33 0.00 99
SECTION TRANSITION S60 S35 (ADD SK 225 - SK 560
TOWER CRANE)
C95AP010 SK560 TOWER CRANE, 2.8 TON @ 265' RADIUS, 217 HP E $1,175,791 145.99 34.84 52.26 8.71 13.40 1,557
76.5' HEIGHT (ADD 161 KW GENERATOR &T-
SECTION)
CRANE)
C95AP012 S60 CLIMB UNIT TOWER CRANE OPTION, 32.8' CLIMBING $167,224 17.61 4.96 7.43 1.24 0.00 258
UNIT (ADD TO SK 225 - SK 560 TOWER
CRANE)
C95AP013 SN355 TOWER CRANE, 3.8 TON @ 197' RADIUS, 354 HP E $1,125,643 153.89 33.36 50.03 8.34 21.86 2,748
110' TALL, LUFFING (ADD 300 KW
GENERATOR & T-SECTION)
C95AP014 SN35 TOWER TOWER CRANE OPTION, 14.75' TOWER $37,722 3.86 1.12 1.68 0.28 0.00 89
SECTION SECTION (ADD TO SN 141 - SN 355 TOWER
CRANE)
C95AP015 SN35 TOWER CRANE OPTION, 29.2' CLIMBING $145,718 15.42 4.32 6.48 1.08 0.00 248
CLIMBING UNIT UNIT (ADD TO SN 141 - SN 355 TOWER
CRANE)
C95AP016 S35N- TOWER CRANE OPTION, 19.4' T- $50,803 5.21 1.51 2.26 0.38 0.00 99
60TOWER TRANSITION S60 S35N (ADD SN 141 - SK 355
SECTION TOWER CRANE)
2-87
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
C95 PECCO AND WOLFF TOWER CRANES

(MORROW) (continued)
C95AP017 SK140 TOWER CRANE, 3.1 TON @ 151' RADIUS, 125 HP E $476,281 63.64 14.12 21.17 3.53 7.72 1,309
85.0' HEIGHT (ADD 95KW GENERATOR & T-
SECTION)
CRANE)
C95AP019 S16 CLIMBING TOWER CRANE OPTION, 29.2' CLIMBING $90,426 9.76 2.68 4.02 0.67 0.00 165
UNIT UNIT (ADD TO SK140 - SK 200 TOWER
CRANE)
C95AP020 SN141 TOWER CRANE, 1.6 TON @ 147' RADIUS, 89' 223 HP E $524,670 77.92 15.55 23.32 3.89 13.77 1,082
TALL, LUFFING (ADD 200 KW GENERATOR &
T-SECTION)
C95AP021 SN160-16 TOWER CRANE, 2.8 TON @ 164' RADIUS, 88' 258 HP E $820,318 112.51 24.31 36.46 6.08 15.93 1,179
TALL, LUFFING (ADD 250 KW GENERATOR &
T-SECTION)
C95AP022 PH5000-12 TOWER CRANE OPTION, 24 PERSON / 2.4 24 HP E $123,235 15.89 3.65 5.48 0.91 1.48 130
TON MATERIAL ELEVATOR/HOIST (ADD 4.9'
MAST SECTION & 18 KW
GENERATOR)
C95AP023 MAST SECTION TOWER CRANE OPTION, 4.9' MAST-> $2,910 0.30 0.09 0.13 0.02 0.00 3
PERSON/MATERIAL ELEVATOR/HOIST (ADD
WALL TIE & CABLE GUIDE @30')
MORROW EQUIPMENT COMPANY, LLC

C95LH022 97K TOWER CRANE, HORIZONTAL BOOM, JIB 35 HP E $433,403 50.15 12.73 19.03 3.21 2.16 1,593
CRANE, 13.2 TON MAX, 1.9 TON @ 148'
RADIUS, 66' HEIGHT, SELF/ERECTING,
W/FIVE - 7' 10" TOWER SECTIONS/ & ROAD
TRANSPORT EQUIPMENT (ADD 40KW
GENERATOR)
2-88
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
C95 MORROW EQUIPMENT COMPANY, LLC

(continued)
C95LH023 140K TOWER CRANE, HORIZONTAL BOOM, JIB 65 HP E $604,534 71.67 17.76 26.56 4.48 4.01 1,836
CRANE, 11.0 TON MAX, 1.7 TON @ 180' RAD
146' HEIGHT, SELF/ERECTING, W/EIGHT - 9'
10" TOWER SECTIONS/ & ROAD
TRANSPORT EQUIPMENT (ADD 60KW
GENERATOR)
C95LH003 132 HC TOWER CRANE, HORIZONTAL BOOM, JIB 109 HP E $487,075 63.23 14.44 21.65 3.61 6.73 1,156
RADIUS, 147.8' HEIGHT, W/FOURTEEN - 8' 2"
TOWER SECTIONS (ADD 85 KW
GENERATOR)
C95LH005 200 HC TOWER CRANE, HORIZONTAL BOOM, JIB 148 HP E $633,502 82.92 18.77 28.16 4.69 9.14 1,374
RADIUS, 162.7' HEIGHT, W/NINE - 13' 7"
GENERATOR)
C95LH011 390 HC TOWER CRANE, HORIZONTAL BOOM, JIB 223 HP E $1,183,673 147.37 35.08 52.61 8.77 13.77 2,744
RADIUS, 199.1' HEIGHT, W/NINE - 19' 0"
GENERATOR)
C95LH013 550 HC20 TOWER CRANE, HORIZONTAL BOOM, JIB 223 HP E $1,512,024 180.97 44.80 67.20 11.20 13.77 3,765
RADIUS, 237.5' HEIGHT, W/TWELVE - 19' 0"
GENERATOR)
C95LH015 550 HC-L TOWER CRANE, 26.4 TON MAX, 3/4 TON @ 317 HP E $2,015,254 243.42 59.72 89.57 14.93 19.57 5,075
197' RADIUS, 210' HEIGHT, LUFFING, W/SIX
19' 0" TOWER SECTIONS (ADD 480 KW
GENERATOR)
2-89
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
D10 DRILLS, HYDRAULIC TRACK (Add cost for drill steel and bit wear)
SUBCATEGORY 0.10 DRILLS, AIR TRACK (Add cost for drill steel and bit wear)
INGERSOLL RAND ROCK DRILL DIV

D10IR003 ECM350/VL140 DRILL, AIR TRACK, CRAWLER, 2.5-4.0" DIA, 750 CFM A $189,782 27.08 6.57 10.17 1.48 0.00 129
12' FEED (ADD COST FOR DRILL STEEL AND
BIT WEAR, ADD 750 CFM
COMPRESSOR)
SULLIVAN-PALATEK, INC.
D10SU002 RAM EXT, DRILL, AIR TRACK, CRAWLER, 2.5-4.0" DIA, 750 CFM A $233,818 33.19 8.09 12.53 1.82 0.00 152
VCR360 12' FEED (ADD COST FOR DRILL STEEL
AND BIT WEAR, ADD 750 CFM
COMPRESSOR)
D10SU003 RAM EXT, DRILL, AIR TRACK, CRAWLER, 3.0-4.0" DIA, 900 CFM A $239,122 33.92 8.27 12.81 1.86 0.00 205
VCR361 12' FEED (ADD COST FOR DRILL STEEL
COMPRESSOR)
SUBCATEGORY 0.20 DRILLS, HYDRAULIC TRACK (Add cost for drill steel and bit wear)
INGERSOLL RAND ROCK DRILL DIV

D10IR005 ECM590/YH80A DRILL, HYDRAULIC TRACK, CRAWLER, 2.5- 215 HP D-off $511,637 129.66 23.26 38.37 4.07 28.51 245
4.5" DIA, 14' DRIFTER TRAVEL, SELF-
CONTAINED (ADD COST FOR DRILL STEEL
AND BIT WEAR)
SULLIVAN-PALATEK, INC.
D10SU005 SCORPION DRILL, HYDRAULIC TRACK, CRAWLER, 5.25" 260 HP D-off $259,651 88.24 11.81 19.47 2.07 34.48 265
VCR360 DIA, 12' FEED (ADD COST FOR DRILL STEEL
AND BIT WEAR)
2-90
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
D10 SULLIVAN-PALATEK, INC. (continued)

D10SU006 SCORPION DRILL, HYDRAULIC TRACK, CRAWLER, 6.5" 260 HP D-off $262,814 88.84 11.95 19.71 2.09 34.48 265
VCR361 DIA, 12' FEED (ADD COST FOR DRILL STEEL
AND BIT WEAR)
D15 DRILLS, HORIZONTAL

SUBCATEGORY 0.10 DRILLS, HORIZONTAL BORING & GROUND PIERCING (Add cost for drill steel and bit wear)
BOR-IT MANUFACTURING COMPANY INC.

D15BI001 12 MIGHT MAX DRILL, HORIZONTAL BORING, 12" DIA, 12 HP G $16,337 6.65 0.75 1.23 0.13 3.25 18
COMBINED HEAD 28,000 LBS THRUST,
W/100' AUGER TRACK (ADD COST FOR
DRILL STEEL AND BIT WEAR)
D15BI002 20 POWER DRILL, HORIZONTAL BORING, 20" DIA, 20 HP D-off $29,926 8.36 1.36 2.24 0.24 2.65 15
HOUSE II COMBINED HEAD 44,000 LBS THRUST,
D15BI003 24 BRUTE DRILL, HORIZONTAL BORING, 24" DIA, 30 HP D-off $46,124 12.77 2.10 3.46 0.37 3.98 38
COMBINED HEAD 84,000 LBS THRUST,
D15BI004 30 POWER DRILL, HORIZONTAL BORING, 30" DIA, 45 HP D-off $70,532 19.40 3.21 5.29 0.56 5.97 70
PLUS COMBINED HEAD 170,000 LBS THRUST,
D15BI005 36 DRILL, HORIZONTAL BORING, 36" DIA, 62 HP D-off $94,702 26.28 4.30 7.10 0.75 8.22 90
WORKHORSE COMBINED HEAD 225,000 LBS THRUST,
2-91
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
D15 BOR-IT MANUFACTURING COMPANY

INC. (continued)
TERMINATOR COMBINED HEAD 525,000 LBS THRUST,
TERMINATOR II COMBINED HEAD 32,700,000 LBS THRUST,
COMBINED HEAD 1,100,000 LBS THRUST,
D15XX001 MC-500H DRILL, HORIZONTAL BORING, 3" - 6" DIA, $9,656 1.74 0.44 0.72 0.08 0.00 10
15,000 LBS THRUST, HYDRAULIC MOTOR
(ADD COST FOR DRILL STEEL AND BIT
WEAR)
D15XX002 H-12/RM-12 DRILL, HORIZONTAL BORING, 4" - 12" DIA, $14,560 2.63 0.67 1.09 0.12 0.00 12
24,000 LBS THRUST, HYDRAULIC MOTOR
WEAR)
SUBCATEGORY 0.20 DRILLS, HORIZONTAL & DIRECTIONAL (Add cost for drill steel and bit wear)
VERMEER MANUFACTURING CO.

D15VE001 D6x6 DRILL, HORIZONTAL DIRECTIONAL, 2.25" 26 HP D-off $50,230 12.92 2.29 3.77 0.40 3.45 32
DIA, 5,500 LB THRUST, W/150' OF RODS
WEAR)
2-92
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
D15 VERMEER MANUFACTURING CO.

(continued)
D15VE002 D9x13 II DRILL, HORIZONTAL DIRECTIONAL, 2.5" DIA, 47 HP D-off $85,838 22.44 3.90 6.44 0.68 6.23 63
9,000 LB THRUST, W/300' OF RODS (ADD
COST FOR DRILL STEEL AND BIT
WEAR)
WEAR)
WEAR)
WEAR)
WEAR)
WEAR)
WEAR
2-93
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
D15 VERMEER MANUFACTURING CO.

(continued)
D15VE009 MX125 DRILL, HORIZONTAL DIRECTIONAL, 500 6 HP G $7,055 2.98 0.33 0.53 0.06 1.49 6
GAL, DRILLING FLUID MIXING SYSTEM (ADD
TRAILER COST)
D15VE010 MX240 DRILL, HORIZONTAL DIRECTIONAL, 750 22 HP D-off $20,727 7.00 0.95 1.55 0.17 2.92 12
TRAILER COST)
D15VE011 MX240 DRILL, HORIZONTAL DIRECTIONAL, 1,000 22 HP D-off $21,055 7.07 0.96 1.58 0.17 2.92 13
TRAILER COST)
D15VE012 MX240 & MX125 DRILL, HORIZONTAL DIRECTIONAL, 1,500 28 HP D-off $43,141 11.86 1.96 3.24 0.34 3.65 81
GAL, DRILLING FLUID MIXING SYSTEM WITH
TRAILER
D20 DRILLS, CORE, COLUMN MOUNTED (Add cost for drill steel and bit wear)
SUBCATEGORY 0.00 DRILLS, CORE, COLUMN MOUNTED (Add cost for drill steel and bit wear)
ACKER DRILL COMPANY INC.

D20AD007 1200-G DRILL, CORE, COLUMN MOUNTED, 12" DIA 8 HP E $17,108 5.41 0.94 1.60 0.14 0.61 3
MAX CORE HOLE (ADD COST FOR DRILL
STEEL AND BIT WEAR)
Dynatech
D20DN001 M-1 DRILL RIG DRILL, CORE, COLUMN MOUNTED, 1" TO 10" 4 HP E $2,297 0.90 0.13 0.22 0.02 0.27 2
COMBO BIT DIA, CB 350/900 MOTOR (20 AMP)
(INCLUDES VACUUM)
D20DN002 M-2 DRILL RIG DRILL, CORE, COLUMN MOUNTED, 10" BIT 2 HP E $3,306 0.97 0.19 0.31 0.03 0.17 2
COMBO DIA, WEKA DK22 300/640/960 MOTOR (23
AMP) (INCLUDES VACUUM), PROF HEAVY
DUTY
2-94
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
D20 Dynatech (continued)

D20DN003 M-6 DRILL BIT DRILL, CORE, COLUMN MOUNTED, 18" BIT 18 HP G $10,081 7.40 0.56 0.95 0.08 4.87 7
SYSTEM DIA, HYDRUALIC CHAR-LYNN 9.6 CU IN W/
GAS POWER PACK
D20DN004 M-6 DRILL BIT DRILL, CORE, COLUMN MOUNTED, 18" BIT 13 HP E $10,383 3.65 0.57 0.97 0.08 0.95 7
SYSTEM DIA, HYDRUALIC CHAR-LYNN 9.6 CU IN W/
ELECT POWER PACK
HUSQVARNA CONSTRUCTION PRODUCTS

D20HG022 DM 406 H HYDRAULIC DRILL, CORE, COLUMN 18 HP G $14,136 8.27 0.78 1.33 0.11 4.87 8
MOUNTED, 1"-24" BIT DIA WITH POWER
PACK AND DRILL STAND (ADD COST FOR
D25 DRILLS, CORE & DOWELLING (Add cost for drill steel and bit wear)
SUBCATEGORY 0.00 DRILLS, CORE & DOWELLING (Add cost for drill steel and bit wear)
ACKER DRILL COMPANY INC.

D25AD004 ACE W DRILL, CORE, SKID MTD, 725' MAX DRILL 28 HP D-off $86,132 20.54 3.92 6.46 0.69 3.71 35
DEPTH (ADD COST FOR DRILL STEEL AND
BIT WEAR)
D25AD003 BUSH MASTER DRILL, CORE, SKID MTD, 1500' MAX DRILL 69 HP D-off $133,754 35.64 6.08 10.03 1.06 9.15 45
DEPTH (ADD COST FOR DRILL STEEL AND
BIT WEAR)
E-Z DRILL, INC.

D25EZ002 210 B DRILL, CORE, SKID MTD, 0.6''-2.5'' DIA., 18" 100 CFM A $7,787 1.98 0.32 0.51 0.06 0.00 3
DEPTH, HORIZONTAL DOWELLING
ASSEMBLY (ADD COST FOR DRILL STEEL
COMPRESSOR)
2-95
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
D25 E-Z DRILL, INC. (continued)

D25EZ003 210 B SRA DRILL, CORE, SKID MTD, 0.6''-2.5'' DIA., 18" 100 CFM A $8,475 2.12 0.37 0.59 0.07 0.00 3
DEPTH, HORIZONTAL DOWELLING
COMPRESSOR)
D25EZ001 210 B SR DRILL, CORE, SKID MTD, 0.6''-2.5'' DIA., 18" 100 CFM A $8,965 2.21 0.41 0.67 0.07 0.00 3
HORIZONTAL DEPTH, HORIZONTAL DOWELLING
COMPRESSOR)
D25EZ005 210-3 SRA DRILL, CORE, SELF PROPELLED, 0.6''-2.5'' 100 CFM A $30,954 7.18 1.37 2.23 0.25 0.00 12
DIA., 18" DEPTH, DOWELLING MACHINE
WEAR, ADD 100 CFM COMPRESSOR)
D30 DRILLS, EARTH / AUGER (Add cost for drill steel and cutting edge wear)
SUBCATEGORY 0.00 DRILLS, EARTH / AUGER (Add cost for drill steel and cutting edge wear)
HYDRAULIC POWER SYSTEMS, INC.

D30HD001 H-15 DRILL, AUGER, HYDRAULIC, W/60' 8" X 21" 210 HP D-off $170,748 65.83 7.77 12.81 1.36 27.85 146
LEADS, 15,000 FT-LBS TORQUE (ADD COST
FOR DRILL STEEL AND CUTTING EDGE
WEAR AND CRANE)
D30HD002 H-35VT DRILL, AUGER, HYDRAULIC, W/60' 8" X 27" 270 HP D-off $216,093 84.42 9.83 16.21 1.72 35.81 200
WEAR AND CRANE)
D30HD003 H-50VT DRILL, AUGER, HYDRAULIC, W/60' 8" X 33" 335 HP D-off $263,389 104.11 11.98 19.75 2.10 44.43 269
WEAR AND CRANE)
2-96
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
FOREMOST MOBILE DRILLING COMPANY, INC.

D30MR001 MINUTEMAN DRILL, EARTH / AUGER, W/AUGER KIT, 3" 8 HP G $14,708 5.28 0.67 1.10 0.12 2.17 4
DIA, 30' DEPTH, 350 FT-LBS TORQUE,
PORTABLE (ADD COST FOR DRILL STEEL
AND CUTTING EDGE WEAR)
D30MR003 B-31 DRILL, EARTH / AUGER, HYDRAULIC 58 HP D-off $99,568 27.61 4.47 7.36 0.79 7.69 42
AUGER, 14" DIA, 30' DEPTH, 3,500 FT-LBS
TORQUE, TRAILER MOUNTED (ADD COST
WEAR)
D30MR005 B-53 DRILL, EARTH / AUGER, MULTI-PURPOSE, 6" 100 HP D-off 230 HP D-on $239,625 65.90 10.74 17.66 1.91 17.92 120
DIA, 245' DEPTH, 5,955 FT-LBS TORQUE,
W/21,000 GVW TRUCK (W/PTO DRIVE)(ADD
COST FOR DRILL STEEL AND CUTTING
EDGE WEAR)
D30MR006 B-58 DRILL, EARTH / AUGER, MULTI-PURPOSE, 8" 115 HP D-off 260 HP D-on $246,780 70.18 11.06 18.20 1.96 20.52 130
DIA, 250' DEPTH, 7,000 FT-LBS TORQUE
W/33,000 GVW TRUCK (ADD COST FOR
DRILL STEEL AND CUTTING EDGE
WEAR)
D30MR007 B-61HT DRILL, EARTH / AUGER, MULTI-PURPOSE, 8" 115 HP D-off 260 HP D-on $311,440 82.53 14.00 23.04 2.48 20.52 205
DIA, 375' DEPTH, 20,000 FT-LBS TORQUE
W/33,000 GVW TRUCK (ADD COST FOR
DRILL STEEL AND CUTTING EDGE
WEAR)
2-97
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
D35 DRILLS, ROTARY BLASTHOLE (Add cost for drill steel and bit wear)
SUBCATEGORY 0.11 DIESEL, 4.5" THRU 9.875" DIAMETER HOLE (Add cost for drill steel and bit wear)
DRILTECH, INC. (SANDVIK)

D35DT001 D25KS DRILL, ROTARY BLASTHOLE, 5''-6.75'' DIA., 450 HP D-off $811,616 184.58 29.29 46.38 6.10 59.68 620
27,000 LB PULLDOWN, CRAWLER, 88'
DEEP(ADD COST FOR DRILL STEEL AND BIT
WEAR)
D35DT002 D245KS DRILL, ROTARY BLASTHOLE, 5''-8'' DIA., 450 HP D-off $833,585 187.69 30.08 47.63 6.26 59.68 720
DEEP (ADD COST FOR DRILL STEEL AND
BIT WEAR)
D35DT003 D45KS DRILL, ROTARY BLASTHOLE, 6''-9'' DIA., 450 HP D-off $942,760 203.18 34.03 53.87 7.09 59.68 1,050
BIT WEAR)
D35DT004 D50KS DRILL, ROTARY BLASTHOLE, 6''-9.875'' DIA., 525 HP D-off $999,704 222.84 36.08 57.13 7.51 69.63 1,050
BIT WEAR)
D35DT005 D55SP DRILL, ROTARY BLASTHOLE, 6.75''-10'' DIA., 760 HP D-off $1,555,967 337.99 56.15 88.91 11.69 100.79 1,320
45,000 LB PULLDOWN, CRAWLER, 55' DEEP
(SINGLE PASS) (ADD COST FOR DRILL
STEEL AND BIT WEAR)
REICHDRILL
D35RL007 T-650-DII DRILL, ROTARY BLASTHOLE, 5"-6 3/4" DIA, 540 HP D-off 505 HP D-off $733,702 198.27 26.20 41.37 5.51 80.42 560
30,000 LBS PULL BACK, TRUCK MTD, 200'
BIT WEAR)
2-98
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
SUBCATEGORY 0.12 DIESEL, OVER 9.875" DIAMETER (Add cost for drill steel and bit wear)
DRILTECH, INC. (SANDVIK)

D35DT006 D75KS DRILL, ROTARY BLASTHOLE, 9''-11'' DIA., 760 HP D-off $1,357,942 266.62 40.24 60.35 10.06 100.79 1,400
BIT WEAR)
INGERSOLL RAND DRILLING (ATLAS COPCO)

D35IB004 T3W DRILL, ROTARY BLASTHOLE, WATER WELL 465 HP D-off 380 HP D-on $741,834 162.76 21.79 32.57 5.50 69.37 660
6"-24" DIA, 30,000 LB PULL BACK, TRUCK
MTD (ADD COST FOR DRILL STEEL AND BIT
WEAR)
D35IB003 TH-60 DRILL, ROTARY BLASTHOLE, WATER WELL, 475 HP D-off 380 HP D-on $778,445 168.13 22.92 34.30 5.77 70.69 600
12" DIA, 26,500 LBS PULL BACK, TRUCK MTD
WEAR)
D35IB005 T3W DEEPHOLE DRILL, ROTARY BLASTHOLE, WATER WELL 575 HP D-off 380 HP D-on $860,126 192.59 25.29 37.83 6.37 83.96 688
WEAR)
D35IB006 T4W DRILL, ROTARY BLASTHOLE, WATER WELL 600 HP D-off 305 HP D-on $904,432 199.57 26.60 39.79 6.70 85.75 688
WEAR)
2-99
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
F10 FORK LIFTS

SUBCATEGORY 0.00 FORK LIFTS
JCB INC.
F10JC001 930-4 FORK LIFT, ROUGH TERRAIN, 6,000 LBS @ 75 HP D-off $77,059 22.78 3.51 5.84 0.59 8.11 150
28' HIGH STRAIGHT MAST, 4X4
F10JC002 940-4 FORK LIFT, ROUGH TERRAIN, 8,000 LBS @ 75 HP D-off $83,811 23.94 3.84 6.38 0.65 8.11 165
30' HIGH STRAIGHT MAST, 4X4
G10 GENERATOR SETS

SUBCATEGORY 0.10 PORTABLE
WACKER CORPORATION
G10WC001 GP 3800A GENERATOR SET, PORTABLE, 3.7 KW, 8 HP G $1,492 2.25 0.10 0.17 0.01 1.77 2
120/240V, 60 HZ
G10WC002 GP 5600A GENERATOR SET, PORTABLE, 5.6 KW, 11 HP G $1,752 3.04 0.11 0.20 0.01 2.44 2
120/240V, 60 HZ
G10WC003 GS 8.5V GENERATOR SET, PORTABLE, 8.5 KW, 16 HP G $5,585 5.04 0.36 0.63 0.04 3.55 2
120/240V, 60 HZ, WITH ELECTRIC
START
G10WC004 GPS 9700V GENERATOR SET, PORTABLE, 9.7 KW, 18 HP G $3,052 5.00 0.19 0.34 0.02 3.99 2
120/240V, 60 HZ, WITH ELECTRIC
START
G10XX001 1000 GENERATOR SET, PORTABLE, 1 KW 3 HP G $897 0.79 0.06 0.10 0.01 0.55 1
G10XX004 D4500 GENERATOR SET, PORTABLE, 5 KW 9 HP D-off $6,791 2.42 0.43 0.76 0.05 0.97 3
G10XX002 10000 GENERATOR SET, PORTABLE, 10 KW 18 HP G $3,530 5.11 0.23 0.40 0.03 3.99 3
2-100
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
G10 NO SPECIFIC MANUFACTURER

(continued)
G10XX003 10000D GENERATOR SET, PORTABLE, 10 KW 23 HP D-off $13,108 5.37 0.84 1.47 0.10 2.49 9
SUBCATEGORY 0.20 SKID MOUNTED

G10CA020 3304 PKG - P GENERATOR SET, SKID MTD, 113 EKW, 174 HP D-off $32,179 26.31 1.68 2.90 0.23 18.83 37
304DE03 240/480V, 60 HZ PGS PRIME
G10CA012 3306 PKG - GENERATOR SET, SKID MTD, 210 EKW, 240 314 HP D-off $39,821 44.33 2.08 3.58 0.29 33.97 50
306DE39 VOLT, 60 HZ PGS PRIME
G10CA013 3406 PKG - GENERATOR SET, SKID MTD, 275 EKW, 480 405 HP D-off $52,105 57.32 2.73 4.69 0.38 43.82 68
G10CA014 3406 PKG - GENERATOR SET, SKID MTD, 365 EKW, 536 HP D-off $71,197 76.24 3.72 6.41 0.51 57.99 72
406DE30 240/480V, 60 HZ PGS PRIME
412DE3H 240/480V, 60 HZ PGS PRIME
412DE30 240/480V, 60 HZ PGS PRIME
G10CA017 3508 PKG - GENERATOR SET, SKID MTD, 725 EKW, 480 1,000 HP D-off $261,267 164.31 13.64 23.51 1.88 108.19 181
512DE1F VOLT, 60 HZ PGS PRIME
G10XX005 25G GENERATOR SET, SKID MTD, 25 KW 36 HP G $27,568 13.56 1.44 2.48 0.20 7.99 16
2-101
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
G10 NO SPECIFIC MANUFACTURER

(continued)
G10XX008 75D GENERATOR SET, SKID MTD, 75 KW 107 HP D-off $25,996 17.25 1.36 2.34 0.19 11.58 40
G10XX015 750D GENERATOR SET, SKID MTD, 750 KW 1,050 HP D-off $165,083 153.75 8.62 14.86 1.19 113.60 215
G10XX016 1000D GENERATOR SET, SKID MTD, 1,000 1,425 HP D-off $154,696 196.75 8.08 13.92 1.12 154.17 154
KW
G15 GRADERS, MOTOR

SUBCATEGORY 0.00 GRADERS, MOTOR

G15CA001 120-M GRADER, MOTOR, ARTICULATED, 6X4, 12' 138 HP D-off $310,501 55.04 10.27 15.72 2.41 13.97 299
BLADE W/17 TEETH SCARIFIERS
BLADE W/11 TEETH SCARIFIERS
BLADE W/5 RIPPER/SCARIFIERS
BLADE W/5 RIPPER/SCARIFIERS
2-102
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
G15 CATERPILLAR INC. ( MACHINE DIVISION)

(continued)
BLADE W/7 SHANK RIPPER
BLADE W/7 SHANK RIPPER
DEERE & COMPANY

G15JD008 670G GRADER, MOTOR, ARTICULATED, 6X4, 151 HP D-off $244,047 50.42 7.88 11.95 1.90 15.28 343
AWD, 12' BLADE W/5
RIPPER/SCARIFIERS
AWD, 12' BLADE W/5
RIPPER/SCARIFIERS
AWD, 12' BLADE W/5
RIPPER/SCARIFIERS
AWD, 12' BLADE W/5
RIPPER/SCARIFIERS
H10 HAMMERS, HYDRAULIC (Demolition tool) (Add cost for point wear)
SUBCATEGORY 0.00 HAMMERS, HYDRAULIC (Demolition tool) (Add cost for point wear)
NPK CONSTRUCTION EQUIPMENT

H10NP019 GH-06 HAMMERS, HYDRAULIC, 150 FT-LBS, $6,528 2.92 0.49 0.87 0.05 0.00 2
IMPACT FREQUENCY 840 BPM (ADD 150-250
HP HYDRAULIC EXCAVATOR H25)(ADD
COST FOR POINT WEAR)
2-103
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
H10 NPK CONSTRUCTION EQUIPMENT

(continued)
H10NP020 GH-07 HAMMERS, HYDRAULIC, 200 FT-LBS, $6,814 3.02 0.52 0.91 0.06 0.00 3
HP HYDRAULIC EXCAVATOR H25 OR
L50)(ADD COST FOR POINT WEAR)
H10NP021 PH-1 HAMMERS, HYDRAULIC, 350 FT-LBS, $7,970 3.80 0.60 1.06 0.07 0.00 4
IMPACT FREQUENCY 830 BPM (ADD 60-
75HP HYDRAULIC EXCAVATOR H25 OR
H10NP024 PH-4 HAMMERS, HYDRAULIC, 1,300 FT-LBS, $20,562 8.29 1.54 2.74 0.17 0.00 10
H10NP025 GH6 HAMMERS, HYDRAULIC, 2,000 FT-LBS, $36,672 13.94 2.75 4.89 0.30 0.00 22
2-104
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
H10 NPK CONSTRUCTION EQUIPMENT

(continued)
TON HYDRAULIC EXCAVATOR H25)(ADD
H13 HAZARDOUS/TOXIC WASTE EQUIPMENT

SUBCATEGORY 0.11 COMPACTORS (Compression force) 0 THRU 50 TONS
CONSOLIDATED BALING MACHINE COMPANY, INC

H13CB001 DOS RAW WI HAZARDOUS/TOXIC WASTE EQIPMENT, 5 HP E $26,282 5.48 1.32 2.23 0.20 0.31 25
COMPACTOR, RADIOLOGICAL WASTE, 12.5
TON, LOW LEVEL
H13CB002 DOS RAW W2 HAZARDOUS/TOXIC WASTE EQUIPMENT, 10 HP E $28,433 6.35 1.42 2.42 0.21 0.62 25
COMPACTOR, RADIOLOGICAL WASTE, 20
TON, LOW LEVEL
2-105
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
WASTE CONTROL SYSTEMS, INC.

H13CO002 8041CC HAZARDOUS/TOXIC WASTE EQUIPMENT, 5 HP E $11,090 2.73 0.55 0.94 0.08 0.31 167
COMPACTOR, 37 TON HAZARD WASTE IN-
DRUM , EXPLOSION PROOF
ENVIRO-PAK
H13EP001 4000HM HAZARDOUS/TOXIC WASTE EQUIPMENT, 5 HP E $30,995 6.33 1.55 2.63 0.23 0.31 32
COMPACTOR, 30 TON HAZARDOUS WASTE,
HAZ-MAT STORAGE CONTAINER
40"X40"X40"
TEEMARK CORPORATION
H13TH001 DPC60-E50 HAZARDOUS/TOXIC WASTE EQUIPMENT, 5 HP E $14,542 3.11 0.73 1.24 0.11 0.31 20
COMPACTOR, 30 TON DRUM
CRUSHER
H13TH002 DPC60-D90 HAZARDOUS/TOXIC WASTE EQUIPMENT, 9 HP D-off $27,413 6.01 1.34 2.28 0.20 0.97 32
COMPACTOR, 30 TON DRUM CRUSHER,
TRAILER MOUNTED
H13TH003 DPC85-D90 HAZARDOUS/TOXIC WASTE EQUIPMENT, 9 HP D-off $30,918 6.64 1.52 2.57 0.23 0.97 47
COMPACTOR, 42.5 TON DRUM CRUSHER,
TRAILER MOUNTED
ADVANCED ENVIRONMENTAL SOLUTIONS

H13YB001 CCYC HAZARDOUS/TOXIC WASTE EQUIPMENT, 50 HP E $404,259 77.84 20.20 34.36 3.02 3.09 320
COMPACTOR, 700 PSI OPERATING
PRESSURE, FINAL COMPACTED SIZE 39.4"
X 39.4" X 39.4"
H13YB002 CCYC-HD-E HAZARDOUS/TOXIC WASTE EQUIPMENT, 50 HP E $404,259 77.84 20.20 34.36 3.02 3.09 320
COMPACTOR, 1,000 PSI OPERATING
X 39.4" X 39.4"
2-106
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
H13 ADVANCED ENVIRONMENTAL

SOLUTIONS (continued)
H13YB003 CMC-HD HAZARDOUS/TOXIC WASTE EQUIPMENT, 50 HP E $404,259 77.84 20.20 34.36 3.02 3.09 320
COMPACTOR, 1,200 PSI OPERATING
X 39.4" X 39.4"
SUBCATEGORY 0.12 COMPACTORS (Compression force) OVER 50 TONS
WASTE CONTROL SYSTEMS, INC.

H13CO003 8551 HAZARDOUS/TOXIC WASTE EQUIPMENT, 3 HP E $24,468 4.38 1.01 1.63 0.19 0.19 270
DRUM
H13CO004 8564 HAZARDOUS/TOXIC WASTE EQIPMENT, 3 HP E $36,821 6.57 1.51 2.45 0.28 0.19 290
DRUM, W/HEPA FILTER
H13CO006 8560-EX HAZARDOUS/TOXIC WASTE EQUIPMENT, 3 HP E $54,587 9.21 2.23 3.64 0.41 0.19 300
DRUM, W/HEPA FILTER & SS PLATEN &
CHAMBER
H13CO005 8560-EXL HAZARDOUS/TOXIC WASTE EQUIPMENT, 3 HP E $65,667 11.10 2.69 4.38 0.50 0.19 310
DRUM, EXPLOSION PROOF, W/LIQUID
REMOVAL SYSTEM
ENVIRO-PAK
H13EP002 9600HM HAZARDOUS/TOXIC WASTE EQUIPMENT, 8 HP E $40,123 7.30 1.64 2.67 0.30 0.46 100
COMPACTOR, 42.5 TON HAZARDOUS
WASTE, B-25 METAL STORAGE CONTAINER
4'X4'X6'
2-107
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
SUBCATEGORY 0.21 FILTER PRESSES, STATIONARY
KOMLINE-SANDERSON ENGINEERING CO.

H13AY015 L/S 1200/25 HAZARDOUS/TOXIC WASTE EQUIPMENT, 100 CFM A $68,533 12.82 3.27 5.48 0.53 0.00 112
FILTER PRESS, STATIONARY, 25 CF
MEMBRANE, 1,200 MM SQ (ADD 100 CFM
COMPRESSOR)
H13AY016 K/F 1200/25 HAZARDOUS/TOXIC WASTE EQUIPMENT, 100 CFM A $44,129 8.25 2.11 3.53 0.34 0.00 108
CONVENTIONAL, 1,200 MM SQ (ADD 100
CFM COMPRESSOR)
COMPRESSOR)
CFM COMPRESSOR)
COMPRESSOR)
CFM COMPRESSOR)
COMPRESSOR)
2-108
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
H13 KOMLINE-SANDERSON ENGINEERING

CO. (continued)
CFM COMPRESSOR)
COMPRESSOR)
CFM COMPRESSOR)
COMPRESSOR)
CFM COMPRESSOR)
H13AY019 HAZARDOUS/TOXIC WASTE EQUIPMENT, 1 HP E $14,312 3.01 0.68 1.14 0.11 0.06 5
FILTER PRESS, STATIONARY, FILTER
PRESS PLATE SHIFTING UNIT, 1,200 MM SQ,
MECHANIZED
H13AY020 SLC-500 HAZARDOUS/TOXIC WASTE EQUIPMENT, 1 HP E $18,579 3.81 0.89 1.49 0.14 0.06 2
FILTER PRESS, STATIONARY, PLC
CONTROL PANEL - PLATE SHIFTING,
COMPUTER AUTOMATED
2-109
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
USFILTER PERRIN PRODUCTS

H13PR001 PLC 25-1000 HAZARDOUS/TOXIC WASTE EQUIPMENT, 3 HP E $109,284 20.72 5.21 8.74 0.84 0.19 125
STANDARD FILTER PRESS, 1,000 MM
SQ
SQ
SQ
H13PR007 PLC 270-1500 HAZARDOUS/TOXIC WASTE EQUIPMENT, 10 HP E $315,644 59.99 15.07 25.25 2.44 0.62 1,100
FILTER PRESS, STATIONARY, 270 CF MAXI
FILTER PRESS, 1,500 MM SQ
H13PR022 BPR 1200-15H HAZARDOUS/TOXIC WASTE EQUIPMENT, 2 HP E $226,561 42.55 10.81 18.12 1.75 0.12 191
FILTER PRESS, STATIONARY, 47" WIDE
FILTER BELT PRESS, 2 HP
FILTER PRESS, STATIONARY, 78.75" WIDE
FILTER PRESS, STATIONARY, 98.5" WIDE
2-110
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
SUBCATEGORY 0.22 FILTER PRESSES, MOBILE
KOMLINE-SANDERSON ENGINEERING CO.

H13AY031 L/S 1200/25M HAZARDOUS/TOXIC WASTE EQUIPMENT, 100 CFM A $85,523 15.69 4.14 7.00 0.64 0.00 112
FILTER PRESS, MOBILE, 25 CF MEMBRANE,
1,200 MM SQ, TRAILER MOUNTED (ADD 100
CFM COMPRESSOR)
H13AY032 K/F 1200/25M HAZARDOUS/TOXIC WASTE EQUIPMENT, 100 CFM A $56,831 10.50 2.70 4.56 0.42 0.00 109
FILTER PRESS, MOBILE, 25 CF
CONVENTIONAL, 1,200 MM SQ, TRAILER
MOUNTED (ADD 100 CFM
COMPRESSOR)
CFM COMPRESSOR)
COMPRESSOR)
CFM COMPRESSOR)
COMPRESSOR)
2-111
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
H13 KOMLINE-SANDERSON ENGINEERING

CO. (continued)
MEMBRANE, 1,200 MM SQ, TRAILER
COMPRESSOR)
COMPRESSOR)
COMPRESSOR)
COMPRESSOR)
COMPRESSOR)
CONVENTIONAL, 1200 MM SQ, TRAILER
COMPRESSOR)
2-112
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
KOCH-WATER
H13KP001 BFP-0500 HAZARDOUS/TOXIC WASTE EQUIPMENT, 13 HP E $90,422 17.59 4.49 7.62 0.68 0.77 40
FILTER PRESS, MOBILE, FILTER BELT
PRESS, 20" (0.5M) WIDE, 0.6 - 2.0 TONS/HR,
TRAILER MOUNTED (STAND ALONE UNIT,
INCLUDES POLYMER FEED PUMP,
BOOSTER PUMP, SLUDGE PUMP, AND
DISCHARGE CONVEYOR)
DISCHARGE CONVEYOR)
DISCHARGE CONVEYOR)
PRESS, 79" (2.0M) WIDE, 14.0 - 20.0
TONS/HR, TRAILER MOUNTED (STAND
ALONE UNIT, INCLUDES POLYMER FEED
PUMP, BOOSTER PUMP, SLUDGE PUMP,
AND DISCHARGE CONVEYOR)
2-113
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
USFILTER PERRIN PRODUCTS

H13PR002 PLC 25-1000M HAZARDOUS/TOXIC WASTE EQUIPMENT, 3 HP E $309,093 57.89 15.31 26.00 2.31 0.19 145
FILTER PRESS, MOBILE, 25 CF STANDARD
FILTER PRESS, 1,000 MM SQ, TRAILER
MOUNTED (COMPLETE)
H13PR006 180-1500M HAZARDOUS/TOXIC WASTE EQUIPMENT, 5 HP E $272,907 51.54 13.50 22.92 2.04 0.31 705
FILTER PRESS, MOBILE, 180 CF STANDARD
FILTER PRESS,1,500 MM SQ, TRAILER
MOUNTED
H13PR011 BPR 1200-15H- HAZARDOUS/TOXIC WASTE EQUIPMENT, 2 HP E $426,623 79.03 21.19 35.99 3.19 0.12 235
M FILTER PRESS, MOBILE, 47" FILTER BELT
PRESS, TRAILER MOUNTED (STAND ALONE
UNIT, ADD APPURTENANCES SUCH AS
FEED PUMPS, POLYMER SYSTEM, WASH
WATER BOOSTER PUMP, CONVEYOR
ETC.)
ETC.)
M FILTER PRESS, MOBILE, 78.75" FILTER BELT
ETC.)
2-114
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
H13 USFILTER PERRIN PRODUCTS

(continued)
M FILTER PRESS, MOBILE, 98.5" FILTER BELT
ETC.)
ETC.)
SOMAT WASTE REDUCTION TECHNOLOGY

H13S5001 1PB-6D HAZARDOUS/TOXIC WASTE EQUIPMENT, 3 HP E $61,663 11.43 3.08 5.24 0.46 0.19 14
FILTER PRESS, MOBILE, PUSHER SCREW
PRESS, 6-15 GPM CAPACITY, TRAILER
MOUNTED
MOUNTED
MOUNTED
2-115
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
SUBCATEGORY 0.30 CENTRIFUGES
NORTH STAR ENGINEERED PRODUCTS, INC.

H13BC013 GP 35 HAZARDOUS/TOXIC WASTE EQUIPMENT, 3 HP E $16,768 7.03 1.83 3.35 0.15 0.19 9
CENTRIFUGE, FIXED SPEED, TIMER, 35 LB
DRY WT.
H13BC010 305 TX HAZARDOUS/TOXIC WASTE EQUIPMENT, 3 HP E $14,606 6.16 1.59 2.92 0.13 0.19 6
DRY WT.
DRY WT.
H13BC006 605 TX HAZARDOUS/TOXIC WASTE EQUIPMENT, 3 HP E $18,012 7.53 1.96 3.60 0.16 0.19 9
DRY WT.
DRY WT.
DRY WT.
H13BC009 355 HAZARDOUS/TOXIC WASTE EQUIPMENT, 3 HP E $25,695 10.62 2.79 5.14 0.22 0.19 6
CENTRIFUGE, FIXED SPEED, MANUAL
CONTROL, EXPLOSION PROOF, 35 LB
CONTROL, EXPLOSION PROOF, 60 LB
CONTROL, EXPLOSION PROOF, 100
LB
2-116
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
SUBCATEGORY 0.40 SHREDDERS
GRANUTE-SATURN SYSTEMS(MAC CORPORATION)

H13MN001 52-32HT HAZARDOUS/TOXIC WASTE EQUIPMENT, 150 HP E $385,496 90.55 19.04 32.31 2.88 9.26 200
SHREDDER, 32" X 52" OPENING, TRAILER
MTD, W/DIESEL GENERATOR SET/ BELT-
TYPE INFEED & DISCHARGE
CONVEYORS
MTD, W/DIESEL GENERATOR SET, HOOK-
TYPE INFEED FOR TIRES, & DISCHARGE
CONVEYOR
MTD, W/DIESEL GENERATOR SET, CRANE
GRAPPLE & DISCHARGE CONVEYOR
SYSTEM
SHREDDER, 45" X 72" OPENING , TRAILER
MTD, W/DIESEL GENERATOR SET, CRANE
GRAPPLE & DISCHARGE CONVEYOR
SYSTEM
SHRED-TECH LIMITED
H13SH001 ST-25E HAZARDOUS/TOXIC WASTE EQUIPMENT, 20 HP E $59,659 13.28 2.99 5.07 0.45 1.24 20
MTD. (ADD COST FOR CONVEYOR SYSTEM,
POWER SUPPLY, AND TRAILER)
2-117
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
H13 SHRED-TECH LIMITED (continued)

H13SH002 ST-25EL HAZARDOUS/TOXIC WASTE EQUIPMENT, 20 HP E $55,926 12.56 2.80 4.75 0.42 1.24 23
H13SH003 ST-50 HAZARDOUS/TOXIC WASTE EQUIPMENT, 40 HP E $96,223 22.12 4.81 8.18 0.72 2.47 45
H13SH004 ST-50L HAZARDOUS/TOXIC WASTE EQUIPMENT, 40 HP E $100,391 22.92 5.02 8.53 0.75 2.47 50
H13SH007 ST-500L HAZARDOUS/TOXIC WASTE EQUIPMENT, 600 HP E $673,091 184.16 33.64 57.21 5.03 37.05 440
2-118
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
SUBCATEGORY 0.71 WASTE HANDLING EQUIPMENT, DRUM HANDLING
BASCO
H13BB001 VELT 55/35 HAZARDOUS/TOXIC WASTE EQUIPMENT, 10 HP E $15,800 9.53 1.82 3.36 0.14 0.62 11
WASTE HANDLING EQUIPMENT, DRUM
HANDLING, DRUM FILLER, 55 GAL TOP
FILL
H13BB002 2B HAZARDOUS/TOXIC WASTE EQUIPMENT, 15 HP E $20,172 12.41 2.32 4.29 0.17 0.93 19
WASTE HANDLING EQUIPMENT, DRUM
CLEANER, 12 DRUM/HR CAP
INTERIOR
H20 HOISTS & AIR WINCHES

SUBCATEGORY 0.00 HOISTS & AIR WINCHES
INGERSOLL RAND MATERIAL HANDLING

H20BE002 FA2.5i AIR WINCH, MANUAL BRAKE, 24" DRUM, 25 CFM A $34,718 6.97 1.82 3.09 0.27 0.00 11
5,000 LBS CAP, 145 FPM (ADD 700 CFM
COMPRESSOR)
H20BE003 FA5i AIR WINCH, MANUAL BRAKE, 24" DRUM, 25 CFM A $44,884 9.04 2.35 3.99 0.35 0.00 19
COMPRESSOR)
H20BE004 FA10i AIR WINCH, AUTOMATIC BRAKE, 24" DRUM, 31 CFM A $65,203 13.11 3.41 5.80 0.51 0.00 32
COMPRESSOR)
2-119
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
H25 HYDRAULIC EXCAVATORS, CRAWLER MOUNTED

SUBCATEGORY 0.10 0 LBS THRU 12,500 LBS (COMPACT EXCAVATORS)

H25CA034 301.8 HYDRAULIC EXCAVATOR, CRAWLER- 18 HP D-off $39,271 9.92 2.16 3.68 0.32 1.95 37
RUBBER TRACK, 3,800 LBS, 0.04 CY
BUCKET, 7.50' MAX DIGGING DEPTH
H25CA035 303 CR HYDRAULIC EXCAVATOR, CRAWLER- 30 HP D-off $45,683 12.66 2.51 4.28 0.37 3.25 76
H25CA036 305 CR HYDRAULIC EXCAVATOR, CRAWLER- 47 HP D-off $73,478 20.21 4.05 6.89 0.60 5.08 115
Komatsu America International Company

H25KM018 PC20MR-2 HYDRAULIC EXCAVATOR, CRAWLER- 20 HP D-off $50,010 12.27 2.76 4.69 0.41 2.16 51
BUCKET, 8'11" MAX DIGGING DEPTH
H25KM021 PC40MR-2 HYDRAULIC EXCAVATOR, CRAWLER- 39 HP D-off $67,023 17.95 3.68 6.28 0.54 4.22 106
H25KM022 PC58UU-3 HYDRAULIC EXCAVATOR, CRAWLER- 40 HP D-off $85,813 21.75 4.72 8.04 0.70 4.33 115
H25KM023 PC78US-6 HYDRAULIC EXCAVATOR, CRAWLER, 6,200 54 HP D-off $105,663 27.38 5.82 9.91 0.86 5.84 159
LBS, 0.37 CY BUCKET, 12'4" MAX DIGGING
DEPTH
2-120
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
MELROE COMPANY/BOBCAT
H25ME001 323 HYDRAULIC EXCAVATOR, CRAWLER- 13 HP D-off $30,564 7.64 1.69 2.87 0.25 1.44 37
BUCKET, 12' MAX DIGGING DEPTH
SUBCATEGORY 0.11 OVER 12,500 LBS THRU 40,000 LBS

H25CA038 307D HYDRAULIC EXCAVATOR, CRAWLER, 14,310 54 HP D-off $105,811 26.23 5.52 9.34 0.85 5.84 159
LBS, 0.48 CY BUCKET, 15.25' MAX DIGGING
DEPTH
H25CA020 311-CU HYDRAULIC EXCAVATOR, CRAWLER, 24,640 79 HP D-off $135,216 34.77 7.06 11.93 1.09 8.55 258
DEPTH
H25CA021 312-D L HYDRAULIC EXCAVATOR, CRAWLER, 26,900 84 HP D-off $135,809 35.50 7.09 11.98 1.10 9.09 288
DEPTH

H25KC027 SK140SR LC HYDRAULIC EXCAVATOR, CRAWLER, 33,100 93 HP D-off $161,615 41.36 8.44 14.26 1.31 10.04 331
DEPTH
H25KC017 SK70SR HYDRAULIC EXCAVATOR, CRAWLER, 16,400 54 HP D-off $99,049 24.99 5.17 8.74 0.80 5.84 168
DEPTH
2-121
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014

H25KM027 PC128UU-2 HYDRAULIC EXCAVATOR, CRAWLER, 12,200 86 HP D-off $205,575 48.60 10.73 18.14 1.66 9.30 295
LBS, 0.58 CY BUCKET, 16' 0" MAX DIGGING
DEPTH
H25KM001 PC 120-6 HYDRAULIC EXCAVATOR, CRAWLER, 26,950 89 HP D-off $145,053 37.82 7.57 12.80 1.17 9.63 265
DEPTH
H25KM003 PC 160LC-7 HYDRAULIC EXCAVATOR, CRAWLER, 39,400 110 HP D-off $199,655 50.51 10.42 17.62 1.61 11.90 395
DEPTH

H25LB003 130 2XLC HYDRAULIC EXCAVATOR, CRAWLER, 27,100 95 HP D-off $163,695 42.01 8.54 14.44 1.32 10.28 271
DEPTH
H25LB005 160 X2 HYDRAULIC EXCAVATOR, CRAWLER, 35,275 120 HP D-off $191,681 50.28 10.01 16.91 1.55 12.98 362
DEPTH

H25CA040 319CL HYDRAULIC EXCAVATOR, CRAWLER, 40,600 125 HP D-off $146,351 36.30 5.73 9.15 1.15 13.52 405
DEPTH
H25CA022 320D HYDRAULIC EXCAVATOR, CRAWLER, 43,800 128 HP D-off $219,750 47.07 8.60 13.73 1.73 13.85 444
DEPTH
H25CA023 320DL HYDRAULIC EXCAVATOR, CRAWLER, 49,000 128 HP D-off $319,821 61.24 12.51 19.99 2.51 13.85 536
DEPTH, LONG REACH BOOM
2-122
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014

H25KC028 SK260 LC HYDRAULIC EXCAVATOR, CRAWLER, 56,890 176 HP D-off $245,040 56.63 9.58 15.32 1.92 19.04 568
LBS, 1.31 CY BUCKET, 23' MAX DIGGING
DEPTH
H25KC029 SK260 LC LR HYDRAULIC EXCAVATOR, CRAWLER, 56,890 176 HP D-off $327,925 68.37 12.83 20.50 2.58 19.04 568
H25KC030 SK350LC HYDRAULIC EXCAVATOR, CRAWLER, 80,900 238 HP D-off $332,495 76.74 13.00 20.78 2.61 25.75 809
LBS, 2.09 CY BUCKET, 27'7" MAX DIGGING
DEPTH
H25KC019 SK210 LC HYDRAULIC EXCAVATOR, CRAWLER, 48,000 143 HP D-off $200,729 46.25 7.86 12.55 1.58 15.47 480
DEPTH
H25KC020 SK210 LC LR HYDRAULIC EXCAVATOR, CRAWLER, 53,400 143 HP D-off $264,512 55.28 10.35 16.53 2.08 15.47 534

H25KC031 SK485 LC HYDRAULIC EXCAVATOR, CRAWLER, 345 HP D-off $462,259 95.24 14.41 21.67 3.57 37.33 1,117
111,774 LBS 2.75 CY BUCKET, 25.58' MAX
DIGGING DEPTH

H25KM015 PC 600 LC-8 HYDRAULIC EXCAVATOR, CRAWLER, 384 HP D-off $680,249 126.13 21.21 31.89 5.26 41.54 1,332
133,160 LBS, 4.25 CY BUCKET, 27.83' MAX
DIGGING DEPTH
2-123
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
SUBCATEGORY 0.14 OVER 160,000 LBS

H25CA065 390D L HYDRAULIC EXCAVATOR, CRAWLER, 523 HP D-off $1,129,344 182.66 30.95 44.58 8.66 56.58 1,900
190,016LB, 7.6CY BUCKET, 35.13' MAX
DIGGING DEPTH

H25KM009 PC 800 LC-8 HYDRAULIC EXCAVATOR, CRAWLER, 454 HP D-off $996,890 160.37 27.32 39.35 7.64 49.12 1,750
171,070 LBS, 4.05 CY BUCKET, 27.66' MAX
DIGGING DEPTH
H25KM033 PC1800-6 HYDRAULIC EXCAVATOR, CRAWLER, 908 HP D-off $2,326,110 356.98 63.75 91.82 17.84 98.24 3,968
396,800 LBS, 15.70 CY BUCKET, 30'5" MAX
DIGGING DEPTH
SUBCATEGORY 0.21 ATTACHMENTS, MOBILE SHEARS

H25CA055 S305 HYDRAULIC EXCAVATOR, ATTACHMENT, $21,484 7.17 1.69 3.04 0.17 0.00 15
MOBILE SHEARS, SCRAP, 9.4" JAW
OPENING (ADD 10,000 LB HYDRAULIC
EXCAVATOR)
H25CA057 S320B HYDRAULIC EXCAVATOR, ATTACHMENT, $85,920 27.87 6.77 12.17 0.68 0.00 57
EXCAVATOR)
EXCAVATOR)
2-124
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
H25 CATERPILLAR INC. ( MACHINE DIVISION)

(continued)
EXCAVATOR)
LABOUNTY MANUFACTURING,
H25LU001 MSD 7 HYDRAULIC EXCAVATOR, ATTACHMENT, $28,469 9.37 2.25 4.03 0.23 0.00 10
MOBILE SHEARS, 10" JAW OPENING (ADD
10,000 LB HYDRAULIC EXCAVATOR)
H25LU002 MSD 7R HYDRAULIC EXCAVATOR, ATTACHMENT, $32,118 10.63 2.54 4.55 0.26 0.00 11
H25LU003 MSD 15 HYDRAULIC EXCAVATOR, ATTACHMENT, $49,907 16.53 3.94 7.07 0.40 0.00 30
H25LU004 MSD 15R HYDRAULIC EXCAVATOR, ATTACHMENT, $58,019 19.18 4.57 8.22 0.46 0.00 35
H25LU005 MSD 30 - III SV HYDRAULIC EXCAVATOR, ATTACHMENT, $72,682 24.01 5.73 10.30 0.58 0.00 50
H25LU006 MSD 30R - III SV HYDRAULIC EXCAVATOR, ATTACHMENT, $101,872 33.60 8.03 14.43 0.81 0.00 67
H25LU007 MSD 40-III SV HYDRAULIC EXCAVATOR, ATTACHMENT, $86,779 28.74 6.84 12.29 0.69 0.00 70
2-125
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
H25 LABOUNTY MANUFACTURING,

(continued)
H25LU008 MSD 40R-III SV HYDRAULIC EXCAVATOR, ATTACHMENT, $113,521 37.37 8.94 16.08 0.90 0.00 90
SUBCATEGORY 0.22 ATTACHMENTS, MATERIAL HANDLING
BALDERSON, INC.
H25BS001 B315-24 HYDRAULIC EXCAVATOR, ATTACHMENT, $7,136 2.06 0.54 0.95 0.06 0.00 10
MATERIAL HANDLING, 0.50 CY BUCKET,
W/TIPS (ADD 25,000-50,000 LB HYDRAULIC
EXCAVATOR)
2-126
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
H25 BALDERSON, INC. (continued)

H25BS002 B3F-B-30 HYDRAULIC EXCAVATOR, ATTACHMENT, $7,199 2.08 0.54 0.96 0.06 0.00 16
EXCAVATOR)
H25BS003 B315-48 HYDRAULIC EXCAVATOR, ATTACHMENT, $9,370 2.71 0.71 1.25 0.08 0.00 30
EXCAVATOR)
H25BS004 B3F-C-42 HYDRAULIC EXCAVATOR, ATTACHMENT, $12,560 3.62 0.94 1.67 0.10 0.00 22
EXCAVATOR)
H25BS005 B3F-D-66 HYDRAULIC EXCAVATOR, ATTACHMENT, $16,825 4.86 1.26 2.24 0.14 0.00 52
EXCAVATOR)
H25LU023 TW 100 HYDRAULIC EXCAVATOR, ATTACHMENT, $38,483 11.35 2.88 5.13 0.31 0.00 16
MATERIAL HANDLING, GRAPPLE, 1.25CY, 4-
TINE/ 5-TINE (ADD 25,000 LB HYDRAULIC
EXCAVATOR)
EXCAVATOR)
H25LU025 120 TR HYDRAULIC EXCAVATOR, ATTACHMENT, $23,986 7.33 1.80 3.20 0.20 0.00 35
EXCAVATOR)
2-127
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014

(continued)
H25LU026 140 TW HYDRAULIC EXCAVATOR, ATTACHMENT, $27,223 8.36 2.04 3.63 0.22 0.00 48
EXCAVATOR)
H25LU027 160 TR HYDRAULIC EXCAVATOR, ATTACHMENT, $30,428 9.39 2.28 4.06 0.25 0.00 58
EXCAVATOR)
EXCAVATOR)
H25LU034 RDG 60 HYDRAULIC EXCAVATOR, ATTACHMENT, $72,063 21.61 5.40 9.61 0.59 0.00 35
MATERIAL HANDLING, ROTATING
GRAPPLE, 1.75 CY (ADD 38,000-70,000 LB
HYDRAULIC EXCAVATOR)
GRAPPLE, 1.25 CY (ADD 70,000-140,000 LB
GRAPPLE, 2.00 CY (ADD 120,000-160,000 LB
WAIN-ROY, INC.
H25WN001 HYDRAULIC EXCAVATOR, ATTACHMENT, $7,997 2.32 0.61 1.07 0.07 0.00 16
MATERIAL HANDLING, BUCKET, 36"
CONCRETE/PAVEMENT REMOVAL (ADD
2-128
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
SUBCATEGORY 0.23 ATTACHMENTS, CONCRETE PULVERIZERS

H25CA068 P215 HYDRAULIC EXCAVATOR, ATTACHMENT, $50,458 16.83 3.98 7.15 0.40 0.00 46
CONCRETE PULVERIZER, CRUSHER, 16.0"
JAW OPENING (ADD 40,000 LB MIN
CONCRETE PULVERIZER, 30.0" JAW
OPENING (ADD 40,000 LB MIN HYDRAULIC
EXCAVATOR)
CONCRETE PULVERIZER, 34.0" JAW
OPENING (ADD 40,000 LB MIN HYDRAULIC
EXCAVATOR)
KENT DEMOLITION TOOLS

H25KN001 KF12 TLB HYDRAULIC EXCAVATOR, ATTACHMENT, $31,544 11.02 2.49 4.47 0.25 0.00 19
CONCRETE BREAKER, 2,000 FT-LB, W/4.25''
DIA. POINT (ADD 16,000-24,000 LB
H25KN002 KF19 QT HYDRAULIC EXCAVATOR, ATTACHMENT, $43,708 15.08 3.45 6.19 0.35 0.00 31
2-129
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
H25 KENT DEMOLITION TOOLS (continued)

CONCRETE BREAKER, 10,000 FT-LB, W/7.09
'' DIA. POINT (ADD 80,000 LB HYDRAULIC
EXCAVATOR)
H25LU046 CP 40 C HYDRAULIC EXCAVATOR, ATTACHMENT, $34,808 12.11 2.75 4.93 0.28 0.00 29
CONCRETE PULVERIZER, 30" JAW
EXCAVATOR)
H25LU047 CP 60 S HYDRAULIC EXCAVATOR, ATTACHMENT, $41,172 14.34 3.25 5.83 0.33 0.00 30
EXCAVATOR)
EXCAVATOR)
EXCAVATOR)
EXCAVATOR)
2-130
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014

(continued)
H25LU040 UP 45 SV HYDRAULIC EXCAVATOR, ATTACHMENT, $150,603 51.00 11.87 21.34 1.20 0.00 105
CONCRETE PULVERIZER, CRACKING JAWS,
45" JAW OPENING (ADD 55,000 LB
H25LU042 UP 90 HYDRAULIC EXCAVATOR, ATTACHMENT, $222,651 75.78 17.54 31.54 1.77 0.00 171
EXCAVATOR)
EXCAVATOR)
SUBCATEGORY 0.24 ATTACHMENTS, COMPACTORS
ALLIED CONSTRUCTION PRODUCTS

H25AU006 500B HYDRAULIC EXCAVATOR, ATTACHMENT, $6,031 2.01 0.48 0.85 0.05 0.00 5
COMPACTOR, 13" X 27" PLATE, 3,940 LBS
FORCE (ADD 7,000-15,000 LB HYDRAULIC
EXCAVATOR)
2-131
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
H25 ALLIED CONSTRUCTION PRODUCTS

(continued)
H25AU007 1000B HYDRAULIC EXCAVATOR, ATTACHMENT, $7,091 2.36 0.56 1.00 0.06 0.00 11
EXCAVATOR)
H25AU008 1600 HYDRAULIC EXCAVATOR, ATTACHMENT, $11,628 3.88 0.92 1.65 0.09 0.00 16
EXCAVATOR)
EXCAVATOR)
EXCAVATOR)
AMERICAN COMPACTION EQUIPMENT, INC.

H25AX001 DC-24BL HYDRAULIC EXCAVATOR, ATTACHMENT, $8,221 2.74 0.65 1.16 0.07 0.00 25
COMPACTOR, 23" WIDE, SHEEPS FOOT, 3
RIMS - 38" DIA (ADD 25,000-50,000 LB
H25AX003 DC-24EX HYDRAULIC EXCAVATOR, ATTACHMENT, $10,197 3.40 0.80 1.44 0.08 0.00 33
RIMS - 42" DIA (ADD 50,000-75,000 LB
H25AX005 DC-24EXL HYDRAULIC EXCAVATOR, ATTACHMENT, $12,052 4.03 0.96 1.71 0.10 0.00 39
RIMS - 48" DIA (ADD 75,000-110,000 LB
2-132
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
H25 AMERICAN COMPACTION EQUIPMENT,

INC. (continued)
H25AX002 DC-36BL HYDRAULIC EXCAVATOR, ATTACHMENT, $9,301 3.10 0.73 1.32 0.07 0.00 33
RIMS - 38" DIA (ADD 50,000-75,000 LB
H25AX004 DC-36EX HYDRAULIC EXCAVATOR, ATTACHMENT, $11,895 3.97 0.94 1.69 0.09 0.00 43
RIMS - 42" DIA (ADD 50,000-75,000 LB
H25AX006 DC-36EXL HYDRAULIC EXCAVATOR, ATTACHMENT, $15,186 5.06 1.20 2.15 0.12 0.00 53
RIMS - 48" DIA (ADD 75,000-110,000 LB

H25KN007 KHP-35 ME-S HYDRAULIC EXCAVATOR, ATTACHMENT, $6,349 2.27 0.50 0.90 0.05 0.00 4
COMPACTOR, 12" X 26" PLATE, 3000 LB
EXCAVATOR)
H25KN009 KHP-135FT - II HYDRAULIC EXCAVATOR, ATTACHMENT, $13,141 4.53 1.03 1.86 0.10 0.00 14
EXCAVATOR)
H25KN010 KHP-210FT - II HYDRAULIC EXCAVATOR, ATTACHMENT, $18,099 6.18 1.42 2.56 0.14 0.00 23
EXCAVATOR)
2-133
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
WAIN-ROY, INC.
H25WN002 24-3 (15-22.5 HYDRAULIC EXCAVATOR, ATTACHMENT, $8,482 2.83 0.67 1.20 0.07 0.00 22
TON) COMPACTOR, 24'' WIDE, SHEEPSFOOT, 3
RIMS - 33" DIA (ADD 15-22.5 TON
H25WN003 36-4 (15-22.5 HYDRAULIC EXCAVATOR, ATTACHMENT, $9,294 3.10 0.73 1.32 0.07 0.00 26
RIMS - 33" DIA (ADD 15-22.5 TON
H25WN004 24-3 (22.5-30 HYDRAULIC EXCAVATOR, ATTACHMENT, $10,147 3.39 0.80 1.44 0.08 0.00 31
RIMS - 39" DIA (ADD 22.5-30 TON
H25WN005 36-4 (22.5-30 HYDRAULIC EXCAVATOR, ATTACHMENT, $11,505 3.84 0.91 1.63 0.09 0.00 38
RIMS - 39" DIA (ADD 22.5-30 TON
H30 HYDRAULIC EXCAVATORS, WHEEL MOUNTED

SUBCATEGORY 0.01 0 THRU 1.0 CY

H30CA005 M318D HYDRAULIC EXCAVATORS, WHEEL, 33,700 151 HP D-off $207,774 53.73 11.00 18.62 1.69 15.28 393
LBS, 1.00 CY BUCKET, 1-PIECE BOOM, 19'
DIGGING DEPTH, 4X4
H30CA007 M315D HYDRAULIC EXCAVATORS, WHEEL, 35,100 121 HP D-off $175,700 45.00 9.18 15.49 1.43 12.25 352
LBS, 0.70 CY BUCKET, 1-PIECE BOOM, 17' 7"
DIGGING DEPTH, 4X4X2
2-134
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
GRADALL COMPANY
H30GA006 XL4100 III HYDRAULIC EXCAVATORS, WHEEL, 44,851 233 HP D-off D-on $303,541 79.08 16.29 27.64 2.47 23.58 475
LBS, 0.75 CY BUCKET, TELESCOPIC BOOM,
22' 6" DIGGING DEPTH, 6X4
H30GA007 XL 3300 III HYDRAULIC EXCAVATORS, WHEEL, 15,270 138 HP D-off $227,159 54.83 12.24 20.78 1.85 13.97 393
4X4X2
SUBCATEGORY 0.02 OVER 1.0 CY
GRADALL COMPANY
H30GA008 XL 5100 III HYDRAULIC EXCAVATORS, WHEEL, 22,800 163 HP D-off 230 HP D-on $342,221 80.62 14.84 24.23 2.72 21.16 550
25' 4" DIGGING DEPTH, 6X4

H30KM001 PW170ES-6 HYDRAULIC EXCAVATORS, WHEEL, 37,600 123 HP D-off $255,177 52.70 11.37 18.68 2.03 12.45 376
LBS, 1.12 CY BUCKET, 1-PIECE BOOM, 18' 8"
DIGGING DEPTH, 4X4
H35 HYDRAULIC SHOVELS, CRAWLER MOUNTED

SUBCATEGORY 0.12 DIESEL, OVER 5.0 CY

H35CA001 6015 HYDRAULIC SHOVEL, CRAWLER, 9.20 CY 665 HP D-off $1,127,112 230.83 36.58 56.36 8.40 71.95 2,277
BUCKET, BACKHOE, 23' 11" DIGGING
DEPTH
H35CA003 6018 HYDRAULIC SHOVEL, CRAWLER, 13.10 CY 1,104 HP D-off $2,235,931 433.41 72.57 111.80 16.67 119.44 3,981
DEPTH
2-135
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
H35 CATERPILLAR INC. ( MACHINE DIVISION)

(continued)
H35CA004 6030 HYDRAULIC SHOVEL, CRAWLER, 20.10 CY 1,530 HP D-off $3,718,515 685.98 120.70 185.93 27.73 165.53 6,477
BUCKET, FRONT SHOVEL, 8' 2" DIGGING
DEPTH
H35CA005 6050 HYDRAULIC SHOVEL, CRAWLER, 34.00 CY 2,520 HP D-off $7,307,305 1,292.63 237.18 365.37 54.49 272.64 11,838
DEPTH
HITACHI CONSTRUCTION MACHINERY

H35HI006 EX1200-5 HYDRAULIC SHOVEL, CRAWLER, 8.5 CY 641 HP D-off $1,672,785 303.21 54.29 83.64 12.47 69.35 2,447
BUCKET, FRONT SHOVEL, 17' 3" DIGGING
DEPTH
L10 LAND CLEARING EQUIPMENT

SUBCATEGORY 0.00 LAND CLEARING EQUIPMENT
BALDERSON, INC.
L10BS004 BBL7 LAND CLEARING EQUIPMENT, ROCK & $28,155 5.56 1.35 2.25 0.22 0.00 24
ROOT RAKE, 12.0' WIDE, 9 TEETH (ADD 200 -
250 HP TRACTOR DOZER)
L10BS005 BRK8 LAND CLEARING EQUIPMENT, ROCK & $41,169 8.07 1.97 3.29 0.32 0.00 72
ROOT RAKE 12.5' WIDE, 9 TEETH (ADD D8
TRACTOR DOZER 275 - 325 HP)
L10BS002 BMA8 LAND CLEARING EQUIPMENT, MULTI- $41,127 8.06 1.97 3.29 0.32 0.00 68
APPLICATION RAKE, 12.5' WIDE, 9 TEETH
(ADD D8 TRACTOR DOZER 275 - 325
HP)
L10BS007 BLF988DTC LAND CLEARING EQUIPMENT, LOGGING $29,428 6.05 1.41 2.35 0.23 0.00 90
FORK, 92" TINES (ADD 400 - 450 HP FE
LOADER)
2-136
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
BUSH HOG
L10BU005 SM-60 LAND CLEARING EQUIPMENT, ROTARY $10,088 3.01 0.49 0.81 0.08 0.00 17
CUTTER, 5' WIDE-SIDE MTD (ADD FARM 50
HP TRACTOR)
L10BU010 287 LAND CLEARING EQUIPMENT, ROTARY $4,098 1.57 0.20 0.33 0.03 0.00 11
CUTTER, 7' WIDE, 1.5 - 12" HEIGHT (ADD
FARM 40 HP TRACTOR)
CUTTER, 10.5' WIDE, 2 - 14" HEIGHT (ADD
FARM 70 HP TRACTOR)
CUTTER, 15' WIDE, 2 - 14" HEIGHT (ADD
FARM 80 HP TRACTOR)
CUTTER, 20' WIDE, 2 - 14" HEIGHT (ADD
FARM 90 HP TRACTOR)
ROME PLOW CO.

L10RM001 RV8N LAND CLEARING EQUIPMENT, V-TREE $55,053 10.78 2.62 4.40 0.42 0.00 134
CUTTER (ADD 275 - 325 HP TRACTOR
DOZER)
L10RM002 MA-152R-8S LAND CLEARING EQUIPMENT, MULTI- $49,421 9.32 2.36 3.95 0.38 0.00 150
APPLICATION RAKE, 12' 8'' WIDE, 9 TEETH
(ADD 275 - 325 HP TRACTOR DOZER)

L10VE010 SC 252 LAND CLEARING EQUIPMENT, STUMPER, 27 HP G $13,946 8.84 0.66 1.10 0.11 5.48 11
16" DIA WHEEL, TRAILER MTD
L10VE002 SC 352 LAND CLEARING EQUIPMENT, STUMPER, 35 HP G $25,502 12.86 1.20 1.99 0.20 7.11 22
2-137
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
L10 VERMEER MANUFACTURING CO.

(continued)
L10VE009 SC 802 LAND CLEARING EQUIPMENT, STUMPER, 78 HP D-off $39,977 16.33 1.89 3.15 0.31 7.89 40
L10VE005 TS-30 LAND CLEARING EQUIPMENT, TREE 13 HP G $13,365 5.50 0.61 1.02 0.10 2.64 38
SPADE, 30" DIA, 26" DEPTH, TRAILER
MTD
L10VE006 TS-44A LAND CLEARING EQUIPMENT, TREE 20 HP G $35,220 11.24 1.66 2.77 0.27 4.06 66
SPADE, 44" DIA, 40" DEPTH, TRAILER
MTD
L10VE007 TS-50 LAND CLEARING EQUIPMENT, TREE $30,114 7.18 1.44 2.41 0.23 0.00 81
SPADE, 50" DIA, 48" DEPTH (ADD 13,800
GVW TRUCK)
L15 LANDSCAPING EQUIPMENT

SUBCATEGORY 0.00 LANDSCAPING EQUIPMENT
BOWIE INDUSTRIES, INC.

L15BW001 LANCER 500 LANDSCAPING EQUIPMENT, 500 GAL, 25 HP G $20,782 16.02 2.33 4.30 0.18 6.77 25
HYDROMULCHER, TRAILER MTD
L15BW002 VICTOR 800 LANDSCAPING EQUIPMENT, 800 GAL, 35 HP G $38,141 26.13 4.27 7.87 0.33 9.48 48
HYDROMULCHER, TRAILER MTD
L15BW003 VICTOR 1100 LANDSCAPING EQUIPMENT, 1,100 GAL, 50 HP G $43,810 32.94 4.91 9.07 0.37 13.54 60
HYDROMULCHER, GOOSENECK TRAILER
MTD
L15BW004 IMPERIAL 3000 LANDSCAPING EQUIPMENT, 3,000 GAL, 90 HP D-off $63,847 39.64 7.34 13.57 0.55 11.94 88
HYDROMULCHER, TRUCK MTD (ADD 55,000
GVW TRUCK)
2-138
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
FINN CORPORATION
L15FG001 T330 LANDSCAPING EQUIPMENT, 3,000 GAL, 115 HP D-off 310 HP D-off $70,279 53.10 8.07 14.93 0.60 21.74 96
HYDROSEEDER, TRUCK MTD (ADD 56,000
GVW TRUCK)
L15FG002 B260T LANDSCAPING EQUIPMENT, MULCHER, 115 HP D-off $47,305 36.34 5.36 9.91 0.40 15.25 48
STRAW BLOWER, 20 TONS PER HOUR,
TRAILER MOUNTED
HUSQVARNA FOREST & GARDEN CO.

L15HV001 DRT900 LANDSCAPING EQUIPMENT, ROTOTILLER, 5 HP G $806 1.83 0.10 0.17 0.01 1.35 2
17" WIDTH BY 6.5" DEPTH
L15HV002 CRT1350LS LANDSCAPING EQUIPMENT, ROTOTILLER, 10 HP G $1,232 3.50 0.14 0.26 0.01 2.71 3
21" WIDTH BY 7" DEPTH
HOFFCO-COMET
L15HZ001 PH980E POST HOLE DRILL, UP TO 8" DIA, 30" DEEP, 3 HP G $886 1.26 0.11 0.19 0.01 0.81 1
ONE MAN OPERATION
DEERE & COMPANY

L15JD005 MX5 LANDSCAPING EQUIPMENT, ROTARY $2,537 1.05 0.29 0.54 0.02 0.00 8
MOWER, 60" WIDE, MEDIUM DUTY, PTO
DRIVE (ADD 45 - 100 HP AGRICULTURAL
TRACTOR)
TORO
L15TO001 22188 - PRO- LANDSCAPING EQUIPMENT, LAWNMOWER, 6 HP G $1,444 2.39 0.17 0.31 0.01 1.62 1
LINE 21" 21" DECK, REAR BAGGER, PUSH
MOWER
L15TO002 30092 MID-SIZE LANDSCAPING EQUIPMENT, LAWNMOWER, 15 HP G $4,374 6.35 0.46 0.84 0.04 4.06 6
32" DECK, SIDE DISCHARGE, WALK BEHIND
MOWER
2-139
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
L15 TORO (continued)

L15TO003 74448 LANDSCAPING EQUIPMENT, LAWNMOWER, 21 HP G $8,406 9.81 0.92 1.69 0.07 5.69 12
48" DECK, SIDE DISCHARGE, RIDING
MOWER
52" DECK W/Z100 TRACTOR, SIDE
DISCHARGE, RIDING MOWER
60" DECK W/Z500 TRACTOR, SIDE
72" DECK, W/Z500 TRACTOR, SIDE
L15TO009 POWER MAX LANDSCAPING EQUIPMENT, 8 HP G $1,317 2.93 0.15 0.28 0.01 2.17 2
8260E SNOWBLOWER, 26" PATH, 45' THROW
L15TO010 POWER MAX LANDSCAPING EQUIPMENT, 10 HP G $2,025 3.83 0.24 0.43 0.02 2.71 3
11280XE SNOWBLOWER, 28" PATH, 45' THROW
WILLMAR EQUIPMENT COMPANY

L15WI001 S-200 LANDSCAPING EQUIPMENT, SPREADER, 70 $9,017 3.73 0.99 1.81 0.08 0.00 15
CF DRY CHEMICAL (ADD 55 HP FARM
TRACTOR)
L20 LIGHTING SETS, TRAILER MOUNTED

SUBCATEGORY 0.10 METALLIC VAPOR
ALLMAND BROTHERS INC.

L20AB017 MAXI-LITE 7.5/8 LITE SET, TRAILER MTD., 4/1250W, W/7.5 KW 13 HP D-off $14,712 6.75 0.84 1.44 0.12 1.92 21
GEN, ELECTRIC MAST WINCH
2-140
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
L20 ALLMAND BROTHERS INC. (continued)

L20AB018 MAXI-LITE 7.5/8 LITE SET, TRAILER MTD., 4/1,000W, W/8 KW 14 HP D-off $16,402 7.42 0.94 1.61 0.13 2.05 21
CSA GEN, ELECTRIC MAST WINCH
L20AB019 MAXI-LITE 7.5/8 LITE SET, TRAILER MTD., 6/1,000W, W/8 KW 14 HP D-off $19,252 8.31 1.10 1.89 0.15 2.05 21
CSA GEN, ELECTRIC MAST WINCH
L20AB020 NIGHT-LITE LITE SET, TRAILER MTD., 4/1,000W, W/6 KW 12 HP D-off $12,395 5.71 0.70 1.20 0.10 1.65 20
PRO GEN, MANUAL MAST WINCH
L20AB021 NIGHT-LITE LITE SET, TRAILER MTD., 4/1,000W, W/8 KW 14 HP D-off $13,105 6.37 0.74 1.28 0.10 2.05 20
PRO CSA GEN, MANUAL MAST WINCH
L20AB022 NIGHT-LITE LITE SET, TRAILER MTD., 4/1,000W, W/7.5 13 HP D-off $14,795 6.76 0.84 1.44 0.12 1.92 21
PR0 V KW GEN, ELECTRIC MAST WINCH
L20AB023 ECLIPSE LITE SET, TRAILER MTD., 15 LED LAMP, $6,060 1.90 0.34 0.58 0.05 0.00 12
2220/SE ALT FLASHING ARROW, W/TWO 8D BATTERIES
AND 50W SOLAR ARRAY
L20AB024 ECLIPSE LITE SET, TRAILER MTD., 25 LED LAMP, $6,496 2.04 0.37 0.63 0.05 0.00 12
2220/SE APF FLASHING ARROW, W/TWO 8D BATTERIES
AND 50W SOLAR ARRAY
L25 LINE STRIPING EQUIPMENT

SUBCATEGORY 0.00 LINE STRIPING EQUIPMENT
JCL EQUIPMENT CO.

L25JE002 ROAD RUNNER LINE STRIPING EQUIPMENT, STRIPER, 190 HP D-off $154,836 72.39 8.86 15.28 1.22 27.19 116
INTERMEDIATE, 3 GUNS, TRUCK MOUNTED
(17,590 LB GVW), TWO COLORS
L25JE003 HRL-1 LINE STRIPING EQUIPMENT, STRIPER, 6 HP G $3,709 2.76 0.22 0.37 0.03 1.59 9
INTERMEDIATE, 1 GUNS SELF PROPELLED,
SINGLE COLOR
2-141
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
M-B COMPANIES, INC.

L25MB002 5-10 LINE STRIPING EQUIPMENT, STRIPER, 1 5 HP G $6,734 4.49 0.31 0.51 0.05 1.45 6
GUN, WALK-BEHIND, SINGLE COLOR
L25MB005 5-12A LINE STRIPING EQUIPMENT, STRIPER, 2 10 HP G $12,313 7.62 0.64 1.07 0.10 2.90 6
GUNS, WALK BEHIND, SINGLE COLOR
L25MB007 220 LINE STRIPING EQUIPMENT, STRIPER, 23 HP G $57,337 24.02 3.32 5.73 0.45 6.66 30
INTERMEDIATE, 3-4 GUNS, SELF
PROPELLED, THREE COLORS
L25MB006 245 LINE STRIPING EQUIPMENT, STRIPER, 60 HP G $102,192 48.36 5.92 10.22 0.81 17.37 48
INTERMEDIATE, 3 GUNS, SELF PROPELLED,
TWO COLORS
L25MB004 VANMARK 360 LINE STRIPING EQUIPMENT, STRIPER, 190 HP G $167,771 108.13 9.61 16.57 1.32 55.01 133
INTERMEDIATE, 3-4 GUNS, W/11,000 LBS
GVW TRUCK, TWO COLORS
L25MB008 360 LINE STRIPING EQUIPMENT, STRIPER, 190 HP D-off $183,888 81.97 10.34 17.77 1.45 27.19 80
INTERMEDIATE, 3-4 GUNS, THERMAL 120
GAL, TRUCK MTD, TWO COLORS
L30 LOADERS, BELT (Conveyor belts) & ACCESSORIES

SUBCATEGORY 0.00 LOADERS, BELT (Conveyor belts) & ACCESSORIES
HEWITT-ROBINS
L30HW015 V-11 6X16FT, TD LOADER, CONVEYOR BELT & 25 HP E $155,447 33.42 7.18 11.96 1.20 1.54 138
ACCESSORIES, SCREENING PLANT, W/6' X
16' VIBRATORY SLOPE TRIPLE DECK
SCREENS/36"X 16.5' UNDER SCREEN
CONVEYOR/ 7 CY HOPPER/ &
FEEDER
2-142
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014

L30KB001 11-2450 LOADER, CONVEYOR BELT & 15 HP E $36,750 8.76 1.67 2.78 0.28 0.93 57
ACCESSORIES, COVEYOR 50', MOBILE,
CONCRETE & AGGREGATE, 24'' WIDE
L30KB002 11-2460 LOADER, CONVEYOR BELT & 15 HP E $38,695 9.15 1.77 2.94 0.30 0.93 62
ACCESSORIES, CONVEYOR, 60', MOBILE,
CONCRETE & AGGREGATE, 24'' WIDE
METSO MINERALS
L30RA001 CV50D LOADER, CONVEYOR BELT & 25 HP D-off $79,353 18.85 3.70 6.18 0.61 2.70 130
ACCESSORIES, GRIZZLY SINGLE SCREEN,
40 CY/HR TRAILER MTD
SUPERIOR INDUSTRIES, AN ASTEC COMPANY

L30S4001 36''X35' FEED LOADER, CONVEYOR BELT & 15 HP E $24,903 6.31 1.19 1.99 0.19 0.93 33
CONVEY ACCESSORIES, BELT FEEDER
L30S4002 RUN-ON LOADER, CONVEYOR BELT & $21,403 4.24 1.03 1.71 0.17 0.00 28
HYDRAULIC ACCESSORIES, 4 HYDRAULIC JACK
LEG LEGS
L30S4005 HOPPER HOPPER SKIRTING DITCH AND CENTER $1,766 0.34 0.08 0.14 0.01 0.00 9
SKIRTING LINE SIDES
L30S4006 FRAME FRAME SKIRTING DITCH AND CENTER LINE $2,010 0.40 0.10 0.16 0.02 0.00 9
SKIRTING SIDES
TELSMITH INC.
L30TS001 PTC 24IN X LOADER, CONVEYOR BELT & 12 HP E $41,837 9.65 1.83 3.02 0.32 0.74 10
50FT ACCESSORIES, CONVEYOR, TRUSS
FRAME, 24"W X 50'L, WHEEL MTD, 300
TPH
2-143
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
L35 LOADERS, FRONT END, CRAWLER TYPE

SUBCATEGORY 0.00 LOADERS, FRONT END, CRAWLER TYPE

L35CA013 939-C LOADER, FRONT END, CRAWLER, 1.50 CY 90 HP D-off $133,387 39.94 6.37 10.67 1.03 10.68 209
BUCKET
L35CA005 953-D LOADER, FRONT END, CRAWLER, 2.25 CY 148 HP D-off $220,060 65.83 10.50 17.60 1.70 17.56 334
BUCKET
L35CA014 963-D LOADER, FRONT END, CRAWLER, 3.20 CY 160 HP D-off $301,021 84.50 14.36 24.08 2.32 18.99 433
BUCKET
L35CA007 973-C LOADER, FRONT END, CRAWLER, 3.70 CY 242 HP D-off $418,185 119.96 19.96 33.45 3.23 28.72 581
BUCKET

L35KM006 D75S-5 LOADER, FRONT END, CRAWLER, 3.30 CY 200 HP D-off $489,952 129.61 23.38 39.20 3.78 23.73 485
BUCKET
L40 LOADERS, FRONT END, WHEEL TYPE

SUBCATEGORY 0.11 ARTICULATED, 0 THRU 225 HP

L40CA032 904B LOADER, FRONT END, WHEEL, 0.80 CY 52 HP D-off $50,084 15.47 2.28 3.76 0.40 5.63 98
BUCKET, ARTICULATED, 4X4
L40CA033 906 LOADER, FRONT END, WHEEL, 1.00 CY 68 HP D-off $65,918 20.15 3.05 5.04 0.53 7.36 109
L40CA034 908 LOADER, FRONT END, WHEEL, 1.30 CY 76 HP D-off $77,083 27.45 3.26 5.27 0.62 8.22 133
2-144
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
L40 CATERPILLAR INC. ( MACHINE DIVISION)

(continued)
L40CA019 914G LOADER, FRONT END, WHEEL, 1.70 CY 95 HP D-off $108,115 31.61 5.06 8.38 0.87 10.28 175
L40CA022 924Hz LOADER, FRONT END, WHEEL, 2.20 CY 128 HP D-off $150,264 42.93 7.11 11.80 1.21 13.85 242
L40CA015 928Hz LOADER, FRONT END, WHEEL, 2.60 CY 149 HP D-off $148,709 45.18 7.03 11.67 1.19 16.12 276
L40CA023 938H LOADER, FRONT END, WHEEL, 3.65 CY 180 HP D-off $183,535 55.70 8.61 14.28 1.47 19.47 332
CASE CORPORATION
L40CS009 621D LOADER, FRONT END, WHEEL, 2.5 CY 136 HP D-off $168,096 48.34 7.78 12.86 1.35 14.71 261
L40CS010 721D LOADER, FRONT END, WHEEL, 3.0 CY 181 HP D-off $200,757 59.43 9.36 15.50 1.61 19.58 306
L40CS011 821C LOADER, FRONT END, WHEEL, 3.5 CY 187 HP D-off $253,570 72.88 11.42 18.78 2.03 20.23 379

L40KM015 WA95-3 LOADER, FRONT END, WHEEL, 1.40 CY 75 HP D-off $94,443 26.18 4.37 7.21 0.76 8.11 128
2-145
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
SUBCATEGORY 0.12 ARTICULATED, OVER 225 HP

L40CA018 990 H LOADER, FRONT END, WHEEL, 11.00 CY 627 HP D-off $1,406,043 259.48 48.29 75.37 10.60 67.84 1,716
L40CA009 992-K LOADER, FRONT END, WHEEL, 16.00 CY 800 HP D-off $1,940,889 347.32 67.86 106.46 14.63 86.55 2,150
L40CA035 988H LOADER, FRONT END, WHEEL, 9.00 CY 501 HP D-off $813,929 176.32 27.73 43.18 6.14 54.20 1,092

L40KM009 WA600-6 LOADER, FRONT END, WHEEL, 8.00 CY 490 HP D-off $682,667 148.60 23.10 35.90 5.15 53.01 1,019
L40KM010 WA700-3A LOADER, FRONT END, WHEEL, 11.10 CY 684 HP D-off $929,937 206.65 30.59 47.16 7.01 74.00 1,574
L40KM011 WA800-3 LOADER, FRONT END, WHEEL, 13.10 CY 853 HP D-off $1,537,807 303.17 52.88 82.58 11.59 92.29 2,230
SUBCATEGORY 0.20 SKID STEER

L40CA028 216B LOADER, FRONT END, WHEEL, SKID-STEER, 49 HP D-off $33,353 14.45 1.84 3.16 0.26 5.81 54
13.0 CF, 60" BUCKET, 4X4
13.0 CF, 60" BUCKET, 4X4
2-146
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014

(continued)
14.0 CF, 66" BUCKET, 4X4
L40CA031 246C LOADER, FRONT END, WHEEL, SKID-STEER, 74 HP D-off $40,723 19.54 2.25 3.85 0.32 8.78 74
15.4 CF, 72" BUCKET, 4X4
MELROE COMPANY/BOBCAT
L40ME016 S70 LOADER, FRONT END, WHEEL, SKID-STEER, 24 HP D-off $17,983 7.30 1.01 1.74 0.14 2.79 28
6.5 CF, 44" BUCKET, 4X4
6.7 CF, 48" BUCKET, 4X4
14.3 CF, 60" BUCKET
13.0 CF, 54" BUCKET, 4X4
16.3 CF, 66" BUCKET, 4X4
23.3 CF, 78" BUCKET, 4X4
SUBCATEGORY 0.31 TOOL CARRIER & TELESCOPIC HANDLERS, 0 THRU 225 HP

L40CA013 IT14G LOADER, WHEEL, INTEGRATED TOOL 90 HP D-off $126,724 34.80 5.59 9.15 1.01 9.74 180
CARRIER, 1.75 CY LOADER; 6,303 LB @
12.17' HIGH, FORK LIFT, OR 1,841 LB @
22.42' HIGH, MATERIAL HANDLING
ARM
2-147
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014

(continued)
L40CA012 IT38H LOADER, WHEEL, INTEGRATED TOOL 145 HP D-off $202,317 54.91 9.02 14.82 1.61 15.69 279
12.58' HIGH FORK LIFT, OR 3,195 LB @ 23.25'
HIGH, MATERIAL HANDLING ARM
L40CA014 IT62G II LOADER, WHEEL, INTEGRATED TOOL 200 HP D-off $282,078 75.90 12.63 20.76 2.25 21.64 454
12.42' HIGH, FORK LIFT, OR 5,040 LB @
22.67' HIGH, MATERIAL HANDLING
ARM
L50 LOADERS / BACKHOE, WHEEL TYPE

SUBCATEGORY 0.00 LOADERS / BACKHOE, WHEEL TYPE

L50CA001 416F LOADER / BACKHOE, WHEEL, 1.00 CY 87 HP D-off $75,470 23.97 3.31 5.41 0.60 7.29 162
FRONT END BUCKET, 24" DIP, 6.2 CF, 14.5'
DIGGING DEPTH, 4X2
L50CA005 450E LOADER / BACKHOE, WHEEL, 1.50 CY 101 HP D-off $144,896 37.30 6.59 10.87 1.15 8.46 203
FRONT END BUCKET, 36" DIP, 19 CF, 17.1'
DIGGING DEPTH, 4X2
CASE CORPORATION
L50CS005 580 SUPER M LOADER / BACKHOE, WHEEL, 1.00 CY 90 HP D-off $100,956 28.87 4.42 7.23 0.80 7.54 143
SERIES 2 FRONT END BUCKET, 24" DIP, 6.2 CF, 14.25'
DIGGING DEPTH, 4X4
L50CS006 590 SUPER M LOADER / BACKHOE, WHEEL, 1.30 CY 98 HP D-off $121,484 33.60 5.28 8.61 0.97 8.21 153
SERIES 2 FRONT END BUCKET, 24" DIP, 6.4 CF, 18'
DIGGING DEPTH, 4X4, EXTENDAHOE
2-148
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
JCB INC.
L50JC008 3CX14 LOADER / BACKHOE, WHEEL, 1.1 CY FRONT 74 HP D-off $84,844 24.20 3.66 5.95 0.68 6.20 154
END BUCKET, 24" DIP, 7.1 CF, 14.6' DIGGING
DEPTH, 4X4
L50JC009 3CX14 Super LOADER / BACKHOE, WHEEL, 1.4 CY FRONT 91 HP D-off $110,870 30.76 4.84 7.91 0.88 7.62 159
END BUCKET, 24" DIP, 7.1 CF, 14.6' DIGGING
DEPTH, 4X4
L50JC010 3CX15 Super LOADER / BACKHOE, WHEEL, 1.40 CY 109 HP D-off $121,378 34.89 5.33 8.72 0.97 9.13 175
DIGGING DEPTH, 4X4
DIGGING DEPTH, 4X4
DIGGING DEPTH, 4X4
L55 LOADER / BACKHOE, ATTACHMENTS

SUBCATEGORY 0.00 LOADER / BACKHOE, ATTACHMENTS

L55KN001 KB-555 LOADER / BACKHOE, ATTACHMENT, AIR 175 CFM A $7,551 2.98 0.57 1.01 0.06 0.00 6
RAM, 500 FT-LB, W/2.5" DIA. POINT (ADD 175
CFM COMPRESSOR & LDR/BH)
L55KN002 KB-999 LOADER / BACKHOE, ATTACHMENT, AIR 250 CFM A $15,480 6.10 1.16 2.06 0.13 0.00 10
RAM, 1000 FT-LB, W/ 3.5" DIA. POINT (ADD
250 CFM COMPRESSOR & LDR/BH)
L55KN004 KF6TLB LOADER / BACKHOE, ATTACHMENT, HYDRA $14,358 4.67 1.08 1.91 0.12 0.00 7
RAM, 1000 FT-LB, W/3'' DIA. POINT (ADD
12,000-14,000 LB LDR/BH)
2-149
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
L55 KENT DEMOLITION TOOLS (continued)

RAM, 1500 FT-LB, W/3.5'' DIA. POINT (ADD
14,000-20,000 LB LDR/BH)
RAM, 2000 FT-LB, W/4.25'' DIA. POINT (ADD
20,000-30,000 LB LDR/BH)
L60 LOG SKIDDERS

SUBCATEGORY 0.00 LOG SKIDDERS

L60CA013 525 C LOG SKIDDER, 11 SF GRAPPLE, CABLE 160 HP D-off $347,806 79.19 16.94 28.67 2.60 17.31 358
43,000 LBS LINE-PULL AND WINCH, WHEEL,
4X2
L60CA010 527 CABLE LOG SKIDDER, CABLE, 69,200 LBS LINE- 150 HP D-off $379,282 82.13 18.95 32.24 2.83 16.23 407
PULL AND WINCH, BLADE, CRAWLER
L60CA011 527 GRAPPLE LOG SKIDDER, 10 SF GRAPPLE, CABLE 150 HP D-off $414,290 88.03 20.70 35.21 3.09 16.23 473
69,200 LBS LINE-PULL AND WINCH,
CRAWLER
DEERE & COMPANY

L60JD001 540G III LOG SKIDDER, CABLE, 40,525 LBS LINE- 119 HP D-off $167,227 44.41 7.89 13.27 1.25 12.87 219
PULL WINCH AND BLADE, WHEEL,
4X4
L60JD003 548G III - LOG SKIDDER, 8.0 SF GRAPPLE WITH 119 HP D-off $166,654 44.32 7.86 13.23 1.24 12.87 217
GRAPPLE BLADE, WHEEL, 4X4
L60JD004 648H LOG SKIDDER, 10.4 SF GRAPPLE WITH 160 HP D-off $243,924 64.10 11.25 18.86 1.82 17.31 266
BLADE, WHEEL, 4X4
2-150
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
L60 DEERE & COMPANY (continued)

L60JD002 640H LOG SKIDDER, CABLE, 48,867 LBS LINE- 151 HP D-off $219,353 57.10 10.50 17.71 1.64 16.34 239
PULL WINCH AND BLADE, WHEEL,
4X4
L60JD006 643K LOG SKIDDER, LOG FELLER/BUNCHER, 18" 170 HP D-off $210,703 58.63 9.87 16.60 1.57 18.39 320
DIA TREE SAW CUTTER, WHEEL, 4X4
L60JD008 753J LOG SKIDDER, LOG FELLER/BUNCHER, 28" 170 HP D-off $408,266 89.44 20.40 34.70 3.05 18.39 410
DIA TREE SAW CUTTER, CRAWLER
L60JD007 843K LOG SKIDDER, LOG FELLER/BUNCHER, 20" 200 HP D-off $224,934 64.67 10.59 17.81 1.68 21.64 323
DIA TREE SAW CUTTER, WHEEL, 4X4
M10 MARINE EQUIPMENT (NON DREDGING)

SUBCATEGORY 0.41 WORK FLOATS (NON-DREDGING)
MARINE INLAND FABRICATORS

M10MZ001 BARGE 40'x8'x4' MARINE EQUIPMENT, WORK BARGE, $23,568 5.82 1.95 3.54 0.18 0.00 143
SECTIONAL, MEDIUM DUTY, 40' X 8' X 4', 23
TON
M10MZ003 BARGE MARINE EQUIPMENT, WORK BARGE, $27,561 6.80 2.28 4.13 0.21 0.00 173
40'x10'x4' SECTIONAL, MEDIUM DUTY, 40' X 10' X 4', 30
TON
SUBCATEGORY 0.42 WORK BARGES (SECTIONAL, NON-DREDGING)

40'x12'x4' SECTIONAL, MEDIUM DUTY', 40' X 12' X 4',
36 TON
2-151
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
M10 MARINE INLAND FABRICATORS

(continued)
40'x12'x5' SECTIONAL, MEDIUM DUTY, 40' X 12' X 5', 51
TON
M10XX001 MARINE EQUIPMENT, WORK BARGE, $7,144 0.41 0.16 0.21 0.05 0.00 1
SECTIONAL, BOW AND STERN
SECTIONS
SECTIONAL, LOADING RAMPS
SECTIONAL, MID-SECTION, 20' X 10' X
5'
SECTIONAL, MID-SECTION, 40' X 10' X
5'
SUBCATEGORY 0.45 FLAT-DECK OR CARGO BARGE (NON-DREDGING)
M10XX005 MARINE EQUIPMENT, FLAT-DECK CARGO $187,656 4.49 2.16 1.98 1.17 0.00 1
BARGE, 120' X 30' X 7.25', 400 TON
BARGE, 120' X 45' X 7', 800 TON
BARGE, 140' X 45' X 7', 900 TON
BARGE, 150' X 45' X 9', 1,100 TON
2-152
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
SUBCATEGORY 0.48 ALL OTHER BARGES (NON-DREDGING)
M10XX016 OPEN 195 MARINE EQUIPMENT, ALL OTHER BARGES, $280,405 17.68 6.24 8.88 1.80 0.00 1
HOPPER, 195' X 35' X 12', 1,400 TON
M10XX017 OPEN 200 MARINE EQUIPMENT, ALL OTHER BARGES, $296,472 18.69 6.60 9.39 1.90 0.00 1
HOPPER, 200' X 35' X 12', 1,600 TON
M10XX018 CLOSED 195 MARINE EQUIPMENT, ALL OTHER BARGES, $369,262 23.28 8.22 11.69 2.37 0.00 1
HOPPER, 195' X 35' X 12', 1,400 TON
(COVERED)
M10XX019 CLOSED 200 MARINE EQUIPMENT, ALL OTHER BARGES, $377,315 23.79 8.40 11.95 2.42 0.00 1
HOPPER, 200' X 35' X 12', 1,600 TON
(COVERED)
SUBCATEGORY 0.51 BOATS & LAUNCHES, 0 THRU 250 HP

M10MZ010 COLT MARINE EQUIPMENT, BOATS & LAUNCHES, 140 HP D-off $68,165 24.94 2.30 3.62 0.49 15.15 95
TRUCKABLE WORKBOAT W/PILOT HOUSE &
PUSH KNEES, INBOARD, 20.25' X 8' X
3'
M10MZ011 MUSTANG MARINE EQUIPMENT, BOATS & LAUNCHES, 210 HP D-off $87,796 35.86 2.96 4.66 0.63 22.72 190
TRUCKABLE WORKBOAT W/PILOT HOUSE &
PUSH KNEES, INBOARD, 25.25' X 10' X
3.5'
SEAARK MARINE
M10SM005 18' - 72 SERIES MARINE EQUIPMENT, BOATS & LAUNCHES, 115 HP G $38,005 33.11 1.28 2.02 0.27 25.51 15
18' RIVER RUNNER, VEE HULL, NO CABIN,
CAP 1,350 LBS, OUTBOARD, 18' X 7.9' X
0.5'
2-153
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
M10 SEAARK MARINE (continued)

M10SM008 19' - UTILITY MARINE EQUIPMENT, BOATS & LAUNCHES, 200 HP G $66,650 57.65 2.25 3.54 0.48 44.37 17
SERIES 19' ROUSTABOUT, TRI HULL, NO CABIN,
CAP 2,600 LBS, OUTBOARD, 19.4' X 8.5' X
0.8'
SERIES 17' LITTLE GIANT, W/CABIN TRI-HULL, CAP
2,000 LBS, OUTBOARD, 17.5' X 7.25' X
0.7'
2,800 LBS, OUTBOARD, 21.4' X 8.5' X 1'
3,400 LBS, OUTBOARD, 23.4' X 8.5' X
1.2'
M10XX010 12 MARINE EQUIPMENT, BOATS & LAUNCHES, 75 HP D-off $56,149 15.45 1.89 2.98 0.40 8.11 1
12' TENDER, 7' BEAM, INBOARD
ENGINE
M10XX009 13 MARINE EQUIPMENT, BOATS & LAUNCHES, 50 HP G $16,713 14.41 0.57 0.89 0.12 11.09 13
13' RUNABOUT, 5' BEAM, OUTBOARD
ENGINE
14' TENDER, 7' BEAM, INBOARD
ENGINE
16', SHALLOW DRAFT, INLAND TUG
22', SHALLOW DRAFT, INLAND TUG
2-154
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
M10 NO SPECIFIC MANUFACTURER

(continued)
18', W/STEERING NOZZLE, INLAND
TUG
26', W/STEERING NOZZLE, INLAND
TUG
SUBCATEGORY 0.53 BOATS & LAUNCHES, 251 THRU 500 HP
40', STANDARD RUDDER, INLAND
TUG
45' LENGTH, 16' BEAM, 5' 0" DRAFT, PUSH
BOAT
48' LENGTH, 20' BEAM, 6' 6" DRAFT PUSH
BOAT
58' LENGTH, 21' BEAM, 6' 0" DRAFT, PUSH
BOAT
2-155
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
P10 PILE HAMMER ACCESSORIES - EXTRACTORS & BOX LEADS

SUBCATEGORY 0.00 PILE HAMMER ACCESSORIES - EXTRACTORS & BOX LEADS
INTERNATIONAL CONSTRUCTION EQUIPMENT,INC

P10IC001 216 PILE HAMMER ACCESSORIES, PILE 175 HP D-off $119,496 53.15 7.54 12.95 1.06 18.93 130
EXTRACTOR, 30 TON LINE PULL (ADD
LEADS & CRANE)
P10IC002 416L PILE HAMMER ACCESSORIES, PILE 300 HP D-off $188,089 86.67 11.85 20.38 1.66 32.46 207
LEADS & CRANE)
P10IC005 1412B PILE HAMMER ACCESSORIES, PILE 800 HP D-off $505,342 232.11 31.85 54.75 4.47 86.55 593
LEADS & CRANE)
P10IC010 PILE HAMMER ACCESSORIES, PILE LEADS, $16,995 4.49 1.07 1.84 0.15 0.00 101
SWING, 26" X 86'
P10IC012 PILE HAMMER ACCESSORIES, PILE LEADS, $23,876 6.31 1.51 2.59 0.21 0.00 155
SWING, 32" X 88'
P10IC011 PILE HAMMER ACCESSORIES, PILE LEADS, 13 HP D-off $34,011 10.60 2.14 3.68 0.30 1.41 134
FIXED, 26" X 86', W/SPOTTER
P10IC013 PILE HAMMER ACCESSORIES, PILE LEADS, 13 HP G $41,981 14.38 2.65 4.55 0.37 2.88 193
FIXED, 32" X 88', W/SPOTTER
P20 PILE HAMMERS, DOUBLE ACTING

SUBCATEGORY 0.10 DIESEL

P20IC002 422 PILE HAMMER, DOUBLE ACTING, DIESEL, $108,448 38.31 7.69 13.56 0.91 0.00 122
22,500 FT-LBS, MAX STROKE 5' 8" (ADD
LEADS & CRANE)
2-156
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
P20 INTERNATIONAL CONSTRUCTION

EQUIPMENT,INC (continued)
LEADS & CRANE)
LEADS & CRANE)
SUBCATEGORY 0.20 PNEUMATIC (STEAM/AIR)
MKT MANUFACTURING, INC.

P20MK002 5 PILE HAMMER, DOUBLE ACTING, 250 CFM A $27,460 9.94 2.05 3.66 0.22 0.00 17
PNUEMATIC (STEAM/AIR), 1,000 FT-LBS,
MAX STROKE 7" (ADD 250 CFM
COMPRESSOR, LEADS & CRANE)
MAX STROKE 8.75" (ADD 400 CFM
MAX STROKE 9.5" (ADD 450 CFM
P20MK005 9B3 PILE HAMMER, DOUBLE ACTING, 600 CFM A $66,778 24.21 5.00 8.90 0.55 0.00 72
2-157
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
P20 MKT MANUFACTURING, INC. (continued)

P25 PILE HAMMERS, SINGLE ACTING

SUBCATEGORY 0.10 DIESEL
PILECO, INC.
P25DL001 D6-42 PILE HAMMER, SINGLE ACTING, DIESEL, 21 HP D-off $26,574 12.18 1.99 3.54 0.22 2.27 36
10,500 FT-LBS (ADD LEADS & CRANE)
107,177 FT-LBS (ADD LEADS &
CRANE)
CRANE)
CRANE)
2-158
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
P25 PILECO, INC. (continued)

CRANE)

P25IC001 30S PILE HAMMER, SINGLE ACTING, DIESEL, 30 HP D-off $74,291 30.09 5.57 9.91 0.61 3.25 73
CRANE)
CRANE)

P25MK001 DE-33/30/20C PILE HAMMER, SINGLE ACTING, DIESEL, 37 HP D-off $63,343 27.68 4.75 8.45 0.52 4.00 78
P25MK003 DE-70/50C PILE HAMMER, SINGLE ACTING, DIESEL, 78 HP D-off $98,053 45.67 7.34 13.07 0.80 8.44 153
2-159
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
SUBCATEGORY 0.20 PNEUMATIC (STEAM/AIR)
VULCAN FOUNDATION EQUIPMENT, INC

P25VU002 306 PILE HAMMER, SINGLE ACTING, 750 CFM A $77,150 28.24 6.08 10.93 0.61 0.00 121
PNUEMATIC (STEAM/AIR), 18,000 FT-LBS
(ADD 750 CFM COMPRESSOR, LEADS &
CRANE)
CRANE)
CRANE)
CRANE)
P25VU010 510 PILE HAMMER, SINGLE ACTING, 1,050 CFM A $133,897 45.62 10.55 18.97 1.06 0.00 222
(ADD 1,050 CFM COMPRESSOR, LEADS &
CRANE)
P25VU011 512 PILE HAMMER, SINGLE ACTING, 1,200 CFM A $135,644 46.43 10.69 19.22 1.08 0.00 242
(ADD 1,200 CFM COMPRESSOR, LEADS &
CRANE)
2-160
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
P30 PILE HAMMERS, DRIVER/ EXTRACTOR, VIBRATORY

SUBCATEGORY 0.00 PILE HAMMERS, DRIVER/ EXTRACTOR, VIBRATORY

P30MK001 V-5C/HP-185 PILE HAMMER, DRIVER/EXTRACTOR, 185 HP D-off $105,896 57.26 7.93 14.12 0.87 20.02 120
VIBRATORY, 53 TON FORCE DRIVE (ADD
LEADS & CRANE)
P30MK003 V-20B/HP-365 PILE HAMMER, DRIVER/EXTRACTOR, 325 HP D-off $179,726 98.52 13.45 23.96 1.47 35.16 220
VIBRATORY, 98.5 TON FORCE DRIVE (ADD
LEADS & CRANE)
P30MK004 V-35/HP-630 PILE HAMMER, DRIVER/EXTRACTOR, 630 HP D-off $307,559 177.70 23.02 41.01 2.51 68.16 327
VIBRATORY, 200 TON FORCE DRIVE (ADD
LEADS & CRANE)
P35 PIPELAYERS
SUBCATEGORY 0.00 PIPELAYERS

P35CA010 PL61 PIPELAYER, 18' BOOM, 40,000 LBS 125 HP D-off $320,393 53.83 11.57 18.31 2.41 7.42 354
CAPACITY
CAPACITY
CAPACITY
2-161
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
P40 PLATFORMS & MAN-LIFTS

SUBCATEGORY 0.00 PLATFORMS & MAN-LIFTS
GENIE INDUSTRIES
P40GJ016 GRC-12 MAN-LIFT, 38X29.5" PLATFORM W/EXT 1 HP E $13,965 3.29 0.87 1.54 0.10 0.05 20
DECK, 18' HEIGHT, 500 LBS, 24 VOLT DC,
RECHARGABLE BATTERIES
TEREX CORPORATION
P40TE003 TA50RT MAN-LIFT, ARTICULATED BOOM, 55' 32 HP D-off $93,461 25.36 5.75 10.12 0.69 2.68 154
HEIGHT, 500 LBS, 29' REACH, 4X4, SELF
PROPELLED, 2.2' X 5' PLATFORM
P40TE004 TA60RT MAN-LIFT, ARTICULATED BOOM, 66' 44 HP D-off $107,203 29.59 6.63 11.67 0.79 3.69 241
HEIGHT, 500 LBS, 33' REACH, 4X4, SELF
PROPELLED, 3' X 6' PLATFROM
P40TE005 TB42 MAN-LIFT, STRAIGHT BOOM, 43' HEIGHT, 66 HP D-off $82,315 26.03 5.04 8.86 0.61 5.53 131
650 LBS, 37' REACH, 4X4, SELF PROPELLED,
3' X 6' PLATFORM
3' X 6' PLATFORM
3' X 6' PLATFORM
3' X 6' PLATFORM
3' X 6' PLATFORM
2-162
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
P40 TEREX CORPORATION (continued)

P40TE010 T-292 MAN-LIFT, LINE-TRUCK, W/AERIAL 2' X 2.5' 210 HP D-off $78,380 37.95 4.88 8.60 0.58 17.59 115
PLATFORM, 300 LBS, 34' HEIGHT, 23'
RAD
P40TE011 T-38P MAN-LIFT, LINE-TRUCK, W/AERIAL 2' X 2.5' 210 HP D-off $86,347 40.09 5.32 9.35 0.64 17.59 128
RAD
P40TE012 Digger DerrickC- MAN-LIFT, LINE-TRUCK, W/13.7 TON, 45' 210 HP D-off $128,984 49.75 8.03 14.14 0.96 17.59 268
4045 HIGH-BOOM TILT POLE CLAWS, & 1.5' DIA
AUGER
P40TE013 5FC-52 MAN-LIFT, LINE-TRUCK, W/AERIAL 2' X 4' 210 HP D-off $118,111 47.29 7.34 12.92 0.88 17.59 215
RAD
P40TE014 5FC-55 MAN-LIFT, LINE-TRUCK, W/AERIAL 2' X 2.5' 210 HP D-off $120,357 47.79 7.48 13.17 0.89 17.59 248
RAD
P40TE015 6H-65 MAN-LIFT, LINE-TRUCK, W/AERIAL 2' X 4' 210 HP D-off $136,724 51.51 8.52 15.02 1.01 17.59 255
RAD
P45 PUMPS, GROUT

SUBCATEGORY 0.00 PUMPS, GROUT
AIRPLACO EQUIPMENT CO., INC.

P45AF002 HG-5 PUMP, GROUT, HAND PUMP, 12 CF/HR, 0- $973 0.24 0.06 0.10 0.01 0.00 1
100 PSI, W/O HOPPER (ADD HOSES)
P45AF003 HG-9 PUMP, GROUT, HAND PUMP, 15 CF/HR, 0- $1,407 0.35 0.09 0.15 0.01 0.00 1
100 PSI, W/5 GAL HOPPER (ADD
HOSES)
2-163
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
P45 AIRPLACO EQUIPMENT CO., INC.

(continued)
P45AF008 HGA-530 PUMP, GROUT, 50 CF/HR, 0-250 PSI, SKID 5 CFM A $8,496 2.23 0.51 0.90 0.06 0.00 4
MTD, W/5 GAL HOPPER AND 30 GAL MIXER
(ADD 50 CFM COMPRESSOR & HOSE)
P45AF009 SM-78MD PUMP, GROUT, 0 - 10 GAL/MIN, TRL MTD, 10 HP D-off $18,689 6.57 1.14 1.99 0.14 1.57 13
W/60 GAL HOPPER, 4.5 CF HYDRAULIC
MIXERS, & 12 CFM COMPRESSOR (ADD
HOSE)
P45AF006 MJ-16 PUMP, MUDJACK/ SLABJACKING, 160 12 HP G $11,790 7.40 0.66 1.14 0.09 3.88 7
CF/HR, 0-400 PSI, GROUT-MUD JACKING-
SHOTCRETE, TRAILER MTD, W/5 CF
HOPPER (ADD 2" HOSE)
P45AF010 Pro-Cretor PUMP, GROUT/SHOTCRETE, SELF 46 HP D-off $62,993 23.96 3.80 6.63 0.48 7.22 37
CONTAINED W/ 10 CF MIXER, HIGH
PRESSURE DUAL CYLINDER PUMP, S-
TUBE, TRAILER MTD (ADD HOSE)
P45AF011 COBRA 536 PUMP, GROUT/SHOTCRETE, HIGH 60 HP D-off $57,432 25.03 3.46 6.04 0.44 9.42 49
PRESSURE DUAL CYLINDER GROUT PUMP,
30-36 CY/HR, 0 - 900 PSI, GROUT-MUD JACK-
SHOTCRETE, TRAILER MTD, (ADD UP TO 5"
HOSE)
P45AF007 PG-25 PUMP, GROUT, HIGH VOLUME DUAL 25 HP G $14,823 12.93 0.86 1.50 0.11 8.08 25
PumpMaster CYLINDER GROUT PUMP, 756 CF/HR
CONCRETE, 350 CF/HR SHOTCRETE,
TRAILER MTD, W/5 CF HOPPER (ADD HOSE
1" - 2" DIA)
2-164
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
ALLENTOWN EQUIPMENT
P45AL015 POWER PUMP, GROUT, GROUT-MUD JACK- 46 HP D-off $66,111 24.76 4.00 6.97 0.51 7.22 35
CRETER SHOTCRE, HIGH PRESSURE DUAL
MAGNUM CYLINDER GROUT PUMP, 135 CF/HR, 0 -
1,770 PSI, TRAILER MTD, W/75 GAL
HOPPER/ 82 GAL MIXER/ 3" HOSE
CHEMGROUT, INC.
P45CG001 CG-050 PUMP, GROUT, MINI, AIR, 40 CF/HR, 225 PSI, 15 CFM A $4,364 1.14 0.26 0.46 0.03 0.00 1
PORTABLE, SKID MTD (ADD 15 CFM - 100
PSI COMPRESSOR)
P45CG002 CG-550P PUMP, GROUT, MIXER, AIR, 40 CF/HR, 225 85 CFM A $7,119 1.89 0.43 0.76 0.05 0.00 3
PSI, SKID MTD (ADD 85 CFM - 100 PSI
COMPRESSOR)
P45CG003 CG-500/2C6 PUMP, GROUT, MIXER, AIR, 160 CF/HR, 160 230 CFM A $16,210 4.23 0.98 1.72 0.12 0.00 12
VERSATILE PSI, SKID MTD, 15 GAL HOPPER & 2 - 70 GAL
MIXING TANKS (ADD 250 CFM - 100 PSI
COMPRESSOR)
P45CG007 CG-570 / 3C6 / H PUMP, GROUT, THICK MIX/SPRAY, 64 16 HP G $24,225 11.99 1.48 2.57 0.19 5.17 13
CF/HR, 261 PSI, SKID MTD, 15 GAL HOPPER
& 45 GAL MIXING TANK, W/AIR
COMPRESSOR, POWER UNIT
P45CG006 CG-570 / 3C6 PUMP, GROUT, THICK MIX/SPRAY, 64 16 HP G $30,193 13.50 1.81 3.15 0.23 5.17 15
CF/HR, 261 PSI, TRAILER MTD, 15 GAL
HOPPER & 45 GAL MIXING TANK, W/AIR
COMPRESSOR, POWER UNIT
OLIN ENGINEERING, INC.

P45OE002 5 40 PUMP, GROUT PUMP, 1,134 CF/HR, 750 PSI, 55 HP D-off $30,621 17.41 1.83 3.20 0.23 8.64 42
37 GAL HOPPER, TRAILER MTD, W/POWER
UNIT
2-165
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
P45 OLIN ENGINEERING, INC. (continued)

P45OE003 5 65 PUMP, GROUT PUMP, 1,836 CF/HR, 1100 84 HP D-off $40,490 25.00 2.44 4.25 0.31 13.19 48
PSI, 37 GAL HOPPER, TRAILER MTD,
W/POWER UNIT
P45OE004 5 85 PUMP, GROUT PUMP, 2,295 CF/HR, 1100 120 HP D-off $47,524 33.11 2.86 5.00 0.36 18.85 56
PSI, 37 GAL HOPPER, TRAILER MTD,
W/POWER UNIT
P45OE005 5 140CA PUMP, GROUT PUMP, 3,780 CF/HR, 900 PSI, 181 HP D-off $79,160 51.84 4.77 8.31 0.61 28.43 100
37 GAL HOPPER, TRAILER MTD TANDEM,
W/POWER UNIT
P50 PUMPS, WATER, CENTRIFUGAL, TRASH

SUBCATEGORY 0.11 ENGINE DRIVE
WACKER CORPORATION
P50WC001 PT 2A PUMP, WATER, CENTRIFUGAL, TRASH, 10 HP G $1,140 3.73 0.07 0.11 0.01 3.05 1
ENGINE DRIVE, 2" DIA, 205 GPM @ 100'
HEAD (ADD HOSES)
P50WC002 PT 3A PUMP, WATER, CENTRIFUGAL, TRASH, 15 HP D-off $1,327 2.92 0.08 0.13 0.01 2.25 2
HEAD (ADD HOSES)
P50WC003 PTS 4V PUMP, WATER, CENTRIFUGAL, TRASH, 16 HP D-off $3,446 3.59 0.20 0.34 0.03 2.40 3
HEAD (ADD HOSES)
P50WC004 PTS 6LT PUMP, WATER, CENTRIFUGAL, TRASH, 33 HP D-off $14,161 9.05 0.81 1.39 0.11 4.95 25
ENGINE DRIVE, 6" DIA, 1,300 GPM @ 100'
HEAD ,TRAILER MTD (ADD HOSES)
2-166
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
P50XX001 6'' DIESEL PUMP, WATER, CENTRIFUGAL, TRASH, 60 HP D-off $48,715 21.78 2.82 4.87 0.38 9.00 22
ENGINE DRIVE, 6" DIA, 1,165 GPM, AIR
COOLED (ADD HOSES)
ENGINE DRIVE, 8" DIA, 2,085 GPM, WATER
COOLED (ADD HOSES)
ENGINE DRIVE, 10" DIA, 2,665 GPM, WATER
COOLED (ADD HOSES)
SUBCATEGORY 0.31 HOSES, PUMP, SUCTION & DISCHARGE
GORMAN-RUPP COMPANY
P50GR001 C221-90 PUMP, WATER, CENTRIFUGAL, TRASH, $118 0.08 0.02 0.03 0.00 0.00 1
HOSE, SUCTION, 2" DIA X 20' WITH
COUPLING (PER SECTION)
HOSE, DISCH, 2" DIA X 50' WITH COUPLING
(PER SECTION)
2-167
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
P50 GORMAN-RUPP COMPANY (continued)

(PER SECTION)
(PER SECTION)
(PER SECTION)
P55 PUMPS, WATER, SUBMERSIBLE

GRIFFIN DEWATERING CORP.

P55GF001 4MH PUMP, WATER, SUBMERSIBLE, ENGINE 21 HP D-off $21,866 9.05 1.27 2.19 0.17 3.15 19
DRIVE, 4" DIA, 400 GPM @ 20' HEAD, SKID
MTD (INCLUDES POWER UNIT MODEL
250)(ADD HOSES)
P55GF002 6T PUMP, WATER, SUBMERSIBLE, ENGINE 72 HP D-off $31,320 20.29 1.82 3.13 0.25 10.81 31
DRIVE, 6" DIA, 2,000 GPM @ 20' HEAD, SKID
MTD (INCLUDES POWER UNIT MODEL
400)(ADD HOSES)
SUBCATEGORY 0.02 ELECTRIC DRIVE
GORMAN-RUPP COMPANY
P55GR001 S2A1 PUMP, WATER, SUBMERSIBLE, ELECTRIC, 2 HP E $4,310 1.10 0.26 0.46 0.03 0.17 2
2" DIA, 138 GPM @ 20' HEAD (ADD
HOSES)
2-168
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
P55 GORMAN-RUPP COMPANY (continued)

HOSES)
HOSES)
6" DIA, 1,950 GPM @ 40' HEAD (ADD
HOSES)
WACKER CORPORATION
P55WC001 PS2 500 PUMP, WATER, SUBMERSIBLE, ELECTRIC, 1 HP E $289 0.18 0.02 0.03 0.00 0.09 1
HOSES)
P55WC002 PS2 750 PUMP, WATER, SUBMERSIBLE, ELECTRIC, 1 HP E $591 0.24 0.03 0.06 0.00 0.09 1
HOSES)
P60 PUMPS, WATER, CENTRIFUGAL, DEWATERING

SUBCATEGORY 0.11 SKID MOUNTED, ENGINE DRIVE
RIVERSIDE PUMP MANUFACTURING

P60HO002 S2B PUMP, WATER, CENTRIFUGAL, 4 HP G $900 1.43 0.06 0.09 0.01 1.07 1
DEWATERING, SKID MOUNTED, ENGINE
DRIVE, 2" DIA, 150 GPM @ 22' HEAD (ADD
HOSES)
P60HO003 TP3B PUMP, WATER, CENTRIFUGAL, 8 HP G $1,800 3.19 0.10 0.18 0.01 2.44 1
HOSES)
2-169
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
WACKER CORPORATION
P60WC001 PG 2A PUMP, WATER, CENTRIFUGAL, 4 HP G $455 1.50 0.03 0.05 0.00 1.22 1
HOSES)
P60WC002 PG 3A PUMP, WATER, CENTRIFUGAL, 6 HP G $525 2.20 0.03 0.05 0.00 1.83 1
HOSES)
SUBCATEGORY 0.21 WHEEL MOUNTED, ENGINE DRIVE
GRIFFIN DEWATERING CORP.

P60GF003 250/4"MH PUMP, WATER, CENTRIFUGAL, 21 HP D-off $25,603 9.62 1.45 2.50 0.20 3.15 19
DEWATERING, WHEEL, 4" DIA, 400 GPM @
60' HEAD (ADD HOSES)
P60GF008 400/6"T PUMP, WATER, CENTRIFUGAL, 72 HP D-off $35,055 20.74 2.01 3.45 0.28 10.81 31
DEWATERING, 6" DIA, 1,040 GPM @ 60'
HEAD, SKID MTD. (ADD HOSES)
DEWATERING, WHEEL, 6" DIA, 2,000 GPM @
DEWATERING, WHEEL, 12" DIA, 4,410 GPM
@ 60' HEAD (ADD HOSES)
2-170
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
GORMAN-RUPP COMPANY
P60GR001 14C2-F3L PUMP, WATER, CENTRIFUGAL, 47 HP D-off $26,602 14.40 1.52 2.61 0.21 7.05 20
DEWATERING, WHEEL, 4" DIA, 600 GPM @
P60GR002 16C2-F4L PUMP, WATER, CENTRIFUGAL, 101 HP G $31,052 42.23 1.78 3.05 0.25 30.76 20
P65 PUMPS, WATER, DIAPHRAGM

SUBCATEGORY 0.11 SKID MOUNTED, ENGINE DRIVE
RIVERSIDE PUMP MANUFACTURING

P65HO001 DP2B PUMP, WATER, DIAPHRAGM, SKID MTD, 2" 4 HP G $1,622 1.59 0.09 0.16 0.01 1.07 1
DIA, 33 GPM @ 25' HEAD (ADD
HOSES)
P65HO002 DP3B PUMP, WATER, DIAPHRAGM, SKID MTD, 3" 4 HP G $1,846 1.64 0.10 0.18 0.01 1.07 2
DIA, 80 GPM @ 25' HEAD (ADD
HOSES)
SUBCATEGORY 0.21 WHEEL MOUNTED, ENGINE DRIVE
GORMAN-RUPP COMPANY
P65GR001 3D-13 PUMP, WATER, DIAPHRAGM, WHEEL, 2" DIA 5 HP G $4,757 2.80 0.23 0.38 0.04 1.52 2
SUCTION X 3" DIA DISCHARGE, 56 GPMH @
P65GR002 3D-B PUMP, WATER, DIAPHRAGM, WHEEL, 3" DIA, 2 HP G $5,602 1.76 0.27 0.46 0.04 0.46 2
560 GPM @ 25' HEAD (ADD HOSES)
P65GR003 4D-B PUMP, WATER, DIAPHRAGM, WHEEL, 4" DIA, 3 HP G $13,446 4.01 0.73 1.24 0.11 0.91 3
2-171
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
WACKER CORPORATION
P65WC001 PDT 2A PUMP, WATER, DIAPHRAGM, WHEEL, 2" DIA, 4 HP G $1,585 1.73 0.09 0.16 0.01 1.22 1
P65WC002 PDT 3A PUMP, WATER, DIAPHRAGM, WHEEL, 3" DIA, 4 HP G $1,688 1.76 0.10 0.17 0.01 1.22 2
P70 PUMPS, WATER (For core drills)

P70XX001 75-7.6 PUMP, WATER, FOR CORE DRILLS, 7.6 GPM, 2 HP G $3,723 1.48 0.21 0.35 0.03 0.61 1
75 PSI, MANUAL, SKID (ADD HOSES)
P70XX002 225-17.5 PUMP, WATER, FOR CORE DRILLS, 17.5 6 HP G $9,722 4.14 0.54 0.91 0.08 1.83 1
GPM, 225 PSI, MANUAL, SKID (ADD
HOSES)
R10 RIPPERS & HYDRAULIC BANK SLOPERS (Add cost for point wear)
SUBCATEGORY 0.00 RIPPERS & HYDRAULIC BANK SLOPERS (Add cost for point wear)

R10CA006 D-5C111 RIPPER, SHANK, EACH (ADD D-5 TRACTOR $293 0.07 0.02 0.03 0.00 0.00 1
DOZER & RIPPER & COST FOR POINT
WEAR)
R10CA022 D6RII-174-9198 RIPPER SHANK, EACH (ADD D6RII TRACTOR $1,193 0.28 0.07 0.12 0.01 0.00 2
WEAR)
R10CA023 D6R II - 9J-8926 RIPPER, SHANK, EACH (ADD D-6 TRACTOR $1,204 0.28 0.07 0.12 0.01 0.00 2
WEAR)
2-172
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
R10 CATERPILLAR INC. ( MACHINE DIVISION)

(continued)
R10CA010 D-7R RIPPER, SHANK, EACH (ADD D-7 TRACTOR $1,962 0.47 0.12 0.20 0.02 0.00 2
WEAR)
WEAR)
WEAR)
WEAR)
R10CA001 D-3 RIPPER, 3-SHANKS & BEAM, HYDRAULIC $10,792 2.61 0.63 1.08 0.09 0.00 13
(ADD D-3 TRACTOR DOZER & COST FOR
POINT WEAR)
R10CA003 D-4C SERIES III RIPPER, 3-SHANKS & BEAM, HYDRAULIC $10,792 2.61 0.63 1.08 0.09 0.00 13
POINT WEAR)
R10CA005 D-5C SERIES III RIPPER, 3-SHANKS & BEAM, HYDRAULIC $10,792 2.61 0.63 1.08 0.09 0.00 13
POINT WEAR)
R10CA007 D-6R II RIPPER, 3-SHANKS & BEAM, HYDRAULIC $17,178 4.11 1.00 1.72 0.14 0.00 40
POINT WEAR)
R10CA009 D-7R RIPPER, 3-SHANKS & BEAM, HYDRAULIC $45,357 10.71 2.63 4.54 0.36 0.00 77
POINT WEAR)
2-173
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014

(continued)
R10CA011 D-8R RIPPER, 1-SHANK & BEAM, HYDRAULIC $50,669 11.97 2.94 5.07 0.40 0.00 91
(ADD D-8 TRACTOR DOZER & RIPPER &
POINT WEAR)
POINT WEAR)
POINT WEAR)
POINT WEAR)
POINT WEAR)
POINT WEAR)
POINT WEAR)
2-174
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
R15 ROLLERS, STATIC, TOWED, PNEUMATIC

SUBCATEGORY 0.00 ROLLERS, STATIC, TOWED, PNEUMATIC
SOUTHWEST CONSTRUCTION EQUIPMENT CO.

R15SO001 C-50 ROLLER, STATIC, TOWED, PNEUMATIC, 60 $152,175 24.57 6.41 10.47 1.17 0.00 309
TON, 9.8' WIDE, 4 TIRE (ADD TOWING
UNIT)
R15SO002 C-75 ROLLER, STATIC, TOWED, PNEUMATIC, 75 $167,778 25.80 5.49 8.39 1.29 0.00 347
UNIT)
R15SO003 C-100XL ROLLER, STATIC, TOWED, PNEUMATIC, 100 $235,822 37.15 8.74 13.83 1.82 0.00 551
UNIT)
R20 ROLLERS, STATIC, TOWED, STEEL DRUM

SUBCATEGORY 0.00 ROLLERS, STATIC, TOWED, STEEL DRUM

R20SO001 2DH-RR ROLLER, STATIC, TOWED, 2 STEEL DRUMS, $83,808 14.86 4.00 6.70 0.65 0.00 200
10-20 TON, 60" WIDE X 60" DIA,
SHEEPSFOOT (ADD TOWING UNIT)
2-175
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
R30 ROLLERS, STATIC, SELF-PROPELLED

SUBCATEGORY 0.01 PNEUMATIC

R30BO004 BW11RH ROLLER, STATIC, SELF-PROPELLED, 85 HP D-off $78,947 29.66 4.28 7.36 0.60 11.27 100
PNEUMATIC, 13.50 TON, 68" WIDE, 9 TIRE,
ASPHALT COMPACTOR
R30BO003 BW24R ROLLER, STATIC, SELF-PROPELLED, 110 HP D-off $148,203 47.68 8.52 14.77 1.13 14.59 290
ASPHALT COMPACTOR

R30CA010 PS-150B ROLLER, STATIC, SELF-PROPELLED, 70 HP D-off $85,500 28.36 5.08 8.85 0.65 9.28 85
ASPHALT COMPACTOR
R30CA014 PS-360B ROLLER, STATIC, SELF-PROPELLED, 105 HP D-off $154,941 51.54 8.80 15.23 1.18 13.93 352
ASPHALT COMPACTOR

R30RS003 TRU-PAC 915 ROLLER, STATIC, SELF-PROPELLED, 80 HP D-off $73,596 27.32 4.27 7.41 0.56 10.61 115
PNEUMATIC, 6-15 TON, 68" WIDE, 9 TIRES,
ASPHALT/SOIL COMPACTOR
SAKAI AMERICA, INC.

R30SI002 TS200 ROLLER, STATIC, SELF-PROPELLED, 91 HP D-off $122,938 39.65 7.01 12.13 0.94 12.07 187
PNEUMATIC, 16 TON, 81" WIDE, 9 TIRE,
ASPHALT COMPACTOR
2-176
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
R30 SAKAI AMERICA, INC. (continued)

R30SI003 TS600C ROLLER, STATIC, SELF-PROPELLED, 95 HP D-off $152,921 46.49 8.83 15.31 1.17 12.60 187
ASPHALT COMPACTOR
R30SI004 TS650C ROLLER, STATIC, SELF-PROPELLED, 108 HP D-off $202,677 58.63 11.96 20.81 1.55 14.32 281
ASPHALT COMPACTOR
SUBCATEGORY 0.02 SMOOTH DRUM

R30BO005 BW5AS ROLLER, STATIC, SELF-PROPELLED, 47 HP D-off $85,651 22.22 4.28 7.28 0.64 6.23 130
SMOOTH DRUM, DOUBLE DRUM, 6 TON, 40"
WIDE ASPHALT COMPACTOR
SMOOTH DRUM, DOUBLE DRUM, 10 TON,
50" WIDE ASPHALT COMPACTOR
SMOOTH DRUM, DOUBLE DRUM, 14 TON,
54" WIDE ASPHALT COMPACTOR

R30RS001 300 B ROLLER, STATIC, SELF-PROPELLED, 16 HP G $16,575 7.75 0.83 1.41 0.12 4.33 26
SMOOTH DRUM, DOUBLE DRUM, 1.5 TON,
34" WIDE, ASPHALT COMPACTOR
R30RS002 400 ROLLER, STATIC, SELF-PROPELLED, 40 HP D-off $33,236 11.81 1.67 2.83 0.25 5.30 37
SMOOTH DRUM, DOUBLE DRUM, 2 TON, 40"
WIDE, ASPHALT COMPACTOR
2-177
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
SAKAI AMERICA, INC.

R30SI005 R2H-2 ROLLER, STATIC, SELF-PROPELLED, 75 HP D-off $131,525 34.53 6.57 11.18 0.98 9.95 207
SMOOTH DRUM, 3 DRUMS, 14 TON, 64"
SUBCATEGORY 0.03 TAMPING FOOT, LANDFILL & SOIL COMPACTORS

R30BO009 BC672RB ROLLER, STATIC, SELF-PROPELLED, 442 HP D-off $557,251 146.28 22.81 37.15 4.23 58.62 710
LANDFILL/SOIL COMPACTOR,
SHEEPSFOOT, 4X4, 35 TON, 63" DIA, 19.58'
WIDTH PER 2-PASS, W/BLADE
R30BO008 BC772RB ROLLER, STATIC, SELF-PROPELLED, 442 HP D-off $573,102 148.61 23.46 38.21 4.35 58.62 812

R30CA003 815-F ROLLER, STATIC, SELF-PROPELLED, 240 HP D-off $506,716 109.33 20.74 33.78 3.85 31.83 449
R30CA012 816-F ROLLER, STATIC, SELF-PROPELLED, 220 HP D-off $502,338 105.76 20.57 33.49 3.82 29.18 509
LANDFILL/SOIL COMPACTOR, TAMPING
FOOT, CHOPPER, 4X4, 25.0 TON, 14.75'
R30CA006 825-G II ROLLER, STATIC, SELF-PROPELLED, 315 HP D-off $731,397 153.21 29.94 48.76 5.56 41.78 734
2-178
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014

(continued)
R30CA013 826-H ROLLER, STATIC, SELF-PROPELLED, 315 HP D-off $766,623 158.36 31.38 51.11 5.82 41.78 771
LANDFILL/SOIL COMPACTOR, TAMPING
FOOT, CHOPPER, 4X4, 36.5 TON, 15.66'
R40 ROLLERS, VIBRATORY, TOWED

SUBCATEGORY 0.00 ROLLERS, VIBRATORY, TOWED

R40BO001 BW6 ROLLER, VIBRATORY, TOWED, SINGLE 50 HP D-off $68,393 23.32 3.96 6.84 0.54 7.50 128
DRUM, SMOOTH, 13,000 LB OPER. WT.,
26,550 LB (13.3 TONS) CENTRIFUGAL
FORCE, 67'' WIDE (ADD 180 HP TOWING
UNIT)
R40BO002 BW6S ROLLER, VIBRATORY, TOWED, SINGLE 50 HP D-off $74,053 24.55 4.29 7.41 0.58 7.50 148
DRUM, SHEEPSFOOT, 15,000 LB OPER. WT.,
26,550 LB (13.3 TONS) CENTRIFUGAL
FORCE, 67'' WIDE (ADD 180 HP TOWING
UNIT)
R45 ROLLERS, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM

SUBCATEGORY 0.00 ROLLERS, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM

R45BO004 BW120AD-4 ROLLER, VIBRATORY, SELF-PROPELLED, 33 HP D-off $41,237 16.21 2.39 4.12 0.33 4.95 57
DOUBLE DRUM, SMOOTH, 2.9 TON, 47.2"
WIDE, 2X1, ASPHALT COMPACTOR
2-179
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
R45 COMPACTION AMERICA (BOMAG)

(continued)
R45BO005 BW138AD ROLLER, VIBRATORY, SELF-PROPELLED, 46 HP D-off $60,592 23.40 3.51 6.06 0.48 6.90 92
R45BO008 BW190AD-4 HF ROLLER, VIBRATORY, SELF-PROPELLED, 205 HP D-off $156,265 75.11 9.05 15.63 1.23 30.76 252

R45CA001 CB-214D ROLLER, VIBRATORY, SELF-PROPELLED, 32 HP D-off $53,066 19.08 3.08 5.31 0.42 4.80 81
R45CA005 CB-434D ROLLER, VIBRATORY, SELF-PROPELLED, 70 HP D-off $124,984 44.03 7.24 12.50 0.99 10.50 137
DOUBLE DRUM, SMOOTH, 6.6 TON, 56"
R45CA011 CB-24 ROLLER, VIBRATORY, SELF-PROPELLED, 33 HP D-off $40,761 16.09 2.36 4.08 0.32 4.95 60
2-180
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014

R45RS001 300B ROLLER, VIBRATORY, SELF-PROPELLED, 20 HP D-off $21,320 8.88 1.24 2.13 0.17 3.00 26
SAKAI AMERICA, INC.

R45SI008 SW320-1 ROLLER, VIBRATORY, SELF-PROPELLED, 35 HP D-off $41,287 16.58 2.40 4.13 0.33 5.25 28
R45SI009 SW652 ROLLER, VIBRATORY, SELF-PROPELLED, 78 HP D-off $111,793 42.02 6.47 11.18 0.88 11.71 157
R45SI010 SW850-3 ROLLER, VIBRATORY, SELF-PROPELLED, 127 HP D-off $150,552 60.34 8.72 15.06 1.19 19.06 124
R50 ROLLERS, VIBRATORY, SELF-PROPELLED, SINGLE DRUM

SUBCATEGORY 0.00 ROLLERS, VIBRATORY, SELF-PROPELLED, SINGLE DRUM

R50BO005 BW124DH-40 ROLLER, VIBRATORY, SELF-PROPELLED, 50 HP D-off $59,358 20.77 2.96 4.95 0.48 5.41 60
SINGLE DRUM, SMOOTH, 2.9 TON, 47.2"
WIDE, 3X2, SOIL COMPACTOR
R50BO010 BW124PDH-40 ROLLER, VIBRATORY, SELF-PROPELLED, 50 HP D-off $61,337 20.83 3.31 5.61 0.50 5.41 60
SINGLE DRUM, PAD FOOT, 2.9 TON, 47.2"
R50BO006 BW145D-40 ROLLER, VIBRATORY, SELF-PROPELLED, 75 HP D-off $87,282 29.99 4.76 8.10 0.71 8.11 110
2-181
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
R50 COMPACTION AMERICA (BOMAG)

(continued)
R50BO007 BW177D-40 ROLLER, VIBRATORY, SELF-PROPELLED, 75 HP D-off $101,455 33.46 5.48 9.31 0.82 8.11 159

R50CA001 CS-323C ROLLER, VIBRATORY, SELF-PROPELLED, 70 HP D-off $91,982 30.56 4.99 8.47 0.75 7.57 97
SINGLE DRUM, SMOOTH, 4.6 TON, 50" WIDE,
3X2, SOIL COMPACTOR
R50CA005 CS-433E ROLLER, VIBRATORY, SELF-PROPELLED, 100 HP D-off $129,367 43.22 6.99 11.87 1.05 10.82 147
3X2, SOIL COMPACTOR
SINGLE DRUM, SMOOTH, 16.5 TON, 84"
2-182
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014

(continued)
R50CA002 CP-323C (PADS) ROLLER, VIBRATORY, SELF-PROPELLED, 70 HP D-off $101,836 32.90 5.53 9.39 0.83 7.57 105
SINGLE DRUM, PAD FOOT, 4.6 TON, 50"
3X2, SOIL COMPACTOR
R50CA007 CS-64 ROLLER, VIBRATORY, SELF-PROPELLED, 156 HP D-off $169,885 59.98 9.07 15.37 1.38 16.88 254
R50CA008 CS-74 ROLLER, VIBRATORY, SELF-PROPELLED, 156 HP D-off $198,555 66.77 10.64 18.05 1.61 16.88 340
R50CA013 CS44 ROLLER, VIBRATORY, SELF-PROPELLED, 100 HP D-off $141,374 46.04 7.66 13.02 1.15 10.82 168
3X2, SOIL COMPACTOR
R50CA014 CP44 ROLLER, VIBRATORY, SELF-PROPELLED, 100 HP D-off $169,409 52.69 9.21 15.65 1.38 10.82 168
R50CA015 CS56B ROLLER, VIBRATORY, SELF-PROPELLED, 157 HP D-off $268,761 83.55 14.50 24.64 2.18 16.99 257
R50CA016 CP56B ROLLER, VIBRATORY, SELF-PROPELLED, 157 HP D-off $273,568 84.69 14.77 25.09 2.22 16.99 211
INGERSOLL RAND ROAD MACHINERY DIV

R50IP001 SD-45D ROLLER, VIBRATORY, SELF-PROPELLED, 80 HP D-off $102,156 34.37 5.45 9.24 0.83 8.66 104
SOIL COMPACTOR
2-183
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
SAKAI AMERICA, INC.

R50SI024 TW350 Combo ROLLER, VIBRATORY, SELF-PROPELLED, 28 HP D-off $65,203 19.07 3.50 5.93 0.53 3.03 25
2X1, ASPHALT COMPACTOR
R50SI006 SV201D ROLLER, VIBRATORY, SELF-PROPELLED, 60 HP D-off $85,344 28.12 4.40 7.41 0.69 6.49 41
3X2, SOIL COMPACTOR
R50SI007 SV201T (PADS) ROLLER, VIBRATORY, SELF-PROPELLED, 60 HP D-off $91,405 29.56 4.73 7.98 0.74 6.49 43
3X2, SOIL COMPACTOR
R50SI022 SV400D-2 ROLLER, VIBRATORY, SELF-PROPELLED, 100 HP D-off $115,695 39.98 6.24 10.60 0.94 10.82 156
3X2, SOIL COMPACTOR
2X1, ASPHALT COMPACTOR
R50SI023 SV400TB-2 ROLLER, VIBRATORY, SELF-PROPELLED, 100 HP D-off $130,468 43.47 7.05 11.98 1.06 10.82 72
(PADS) SINGLE DRUM, SMOOTH, 9.6 TON, 67" WIDE,
3X2, SOIL COMPACTOR
R50SI013 SV510D-3 ROLLER, VIBRATORY, SELF-PROPELLED, 148 HP D-off $139,993 51.95 7.40 12.51 1.14 16.01 507
R50SI016 SV510T-3 ROLLER, VIBRATORY, SELF-PROPELLED, 148 HP D-off $150,205 54.37 7.95 13.46 1.22 16.01 110
(PADS) SINGLE DRUM, SMOOTH, 11.9 TON, 60"
R50SI017 SV510TF-3 ROLLER, VIBRATORY, SELF-PROPELLED, 148 HP D-off $162,465 57.27 8.63 14.61 1.32 16.01 131
(PADS) SINGLE DRUM, SMOOTH, 14.3 TON, 85"
2-184
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
R55 ROOFING EQUIPMENT

SUBCATEGORY 0.00 ROOFING EQUIPMENT
GARLOCK EQUIPMENT CO.

R55GL020 300628 ROOFING EQUIPMENT, MATERIAL BUGGY, 5 HP G $5,194 2.58 0.34 0.60 0.04 1.02 4
36'' WIDE, WALK BEHIND GRAVEL
SPREADER, HOPPER 800 LBS, 8 CF,
4X2
R55GL021 Ultracutter ROOFING EQUIPMENT, 1-BLADE CUTTER, 9 HP G $3,058 2.92 0.24 0.43 0.02 1.83 2
300645 3.75" DEEP, WALK BEHIND 11 HP (ADD
BLADE COST)
R55GL022 GENESIS 1012 ROOFING EQUIPMENT, KETTLE, 1,012 GAL, 8 HP G $29,431 17.33 2.19 3.92 0.23 1.62 54
W/PUMP, TRAILER MTD
R55GL023 ROOF ROOFING EQUIPMENT, ROOF PEELER, 16" 8 HP G $8,830 4.37 0.66 1.18 0.07 1.62 6
WARRIOR WIDE, WALK BEHIND, POWERED WHEEL
2X2, STD W/ 18" FLAT BLADE
R55GL024 N0. 78 1-ply graveler 6 HP G $5,903 3.00 0.47 0.84 0.05 1.12 4
R55GL025 Garlock 3610 ROOFING EQUIPMENT, POWER BROOM W/ 7 HP G $4,359 2.75 0.34 0.62 0.03 1.32 4
STEEL BRUSH, 36" WIDE
R55GL017 SUPER MINI ROOFING EQUIPMENT, 1-BLADE CUTTER, 5 HP G $2,534 1.88 0.20 0.36 0.02 1.02 2
SAW 18" HEIGHT & 2" WALL CLEARANCE
R55GL016 DUST MASTER ROOFING EQUIPMENT, 1-BLADE CUTTER, 9 HP G $5,784 3.74 0.46 0.82 0.05 1.83 3
ULTRA CU W/WATER DAMPENING SYSTEM AND
H.E.P.A. VACUUM SYSTEM
R55GL011 ENFORCER ROOFING EQUIPMENT, 2-BLADE CUTTER, 16 HP G $8,219 6.03 0.65 1.16 0.07 3.25 4
TWIN CUTTER 25" WIDE, SELF PROPELLED (ADD BLADE
COST)
R55GL018 NO.12 ROOFING EQUIPMENT, SCRATCHER, 4.5" 5 HP G $2,873 1.98 0.23 0.41 0.02 1.02 1
WIDE
2-185
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
R55 GARLOCK EQUIPMENT CO. (continued)

R55GL019 NO. 30 ROOFING EQUIPMENT, SCRATCHER, 13" 8 HP G $5,600 3.44 0.44 0.79 0.04 1.62 3
WIDE
R55GL009 ROTARY ROOFING EQUIPMENT, ROTARY PLANER, 11 HP G $3,288 3.33 0.27 0.47 0.03 2.13 2
PLANER 12" WIDE
R55GL015 MODEL 1000 ROOFING EQUIPMENT, HYDRAULIC HOIST, 9 HP G $13,601 6.06 1.08 1.93 0.11 1.83 8
W/175' CABLE, 1,000 LB CAP
R55GL007 SUPER MAX ROOFING EQUIPMENT, HYDRAULIC SWING 18 HP G $14,473 8.33 1.15 2.05 0.12 3.65 10
HYDR HOIST HOIST, W/275' CABLE, 1,400 LB CAP
R55GL013 MODEL 30 ROOFING EQUIPMENT, KETTLE, 30 GAL, $1,938 0.72 0.09 0.13 0.02 0.00 3
WHEEL MTD
SKID MTD
TRAILER MTD
R55GL002 MODEL 175 ROOFING EQUIPMENT, KETTLE, 175 GAL, 5 HP G $6,963 3.64 0.52 0.91 0.06 1.02 17
W/PUMP, TRAILER MTD
R55GL012 MODEL 300 ROOFING EQUIPMENT, KETTLE, 300 GAL, 9 HP G $13,114 6.59 0.99 1.78 0.10 1.83 23
W/PUMP, TRAILER MTD
R55GL003 GENESIS 412 ROOFING EQUIPMENT, KETTLE, 412 GAL, 9 HP G $18,593 8.24 1.44 2.57 0.15 1.83 30
W/PUMP, TRAILER MTD
R55GL004 GENESIS 612 ROOFING EQUIPMENT, KETTLE, 612 GAL, 9 HP G $22,612 9.69 1.76 3.15 0.18 1.83 40
W/PUMP, TRAILER MTD
2-186
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
S10 SCRAPERS, ELEVATING

SUBCATEGORY 0.01 0 THRU 200 HP

S10CA001 613-C SERIES II SCRAPER, ELEVATING LOADING, 11 CY, 13 175 HP D-off $321,317 86.49 14.82 24.67 2.48 18.93 336
TON, 7.7' CUT WIDTH, 4X2 - SINGLE
POWERED
SUBCATEGORY 0.02 OVER 200 HP

S10CA003 623-G SCRAPER, ELEVATING LOADING, 23 CY, 25 365 HP D-off $525,958 135.12 18.06 27.90 4.11 39.49 810
TON, 11.5' CUT WIDTH, 4X2 - SINGLE
POWERED
S15 SCRAPERS, CONVENTIONAL

SUBCATEGORY 0.00 SCRAPERS, CONVENTIONAL

S15CA001 621-G SCRAPER, CONVENTIONAL, STANDARD 365 HP D-off $616,807 129.92 20.01 30.78 4.62 36.94 714
LOADING, 21 CY, 24 TON, 9.1' CUT WIDTH,
4X2 - SINGLE POWERED
S15CA002 631-G SCRAPER, CONVENTIONAL, STANDARD 450 HP D-off $903,737 181.29 29.26 44.98 6.77 45.54 1,020
LOADING, 34 CY, 37.5 TON, 11.5' CUT
WIDTH, 4X2 - SINGLE POWERED
2-187
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
ATI-Bell
S15JU001 4206DTIS28 SCRAPER, CONVENTIONAL, STANDARD 422 HP D-off $635,368 130.14 21.13 32.73 4.76 42.71 940
LOADING, 28 CY, 32 TON, 14' CUT WIDTH,
4X4 - SINGLE POWERED, TRACTOR
EQUIPPED WITH ATI RUBBER
TRACKS
S15JU002 4206DTIS33 SCRAPER, CONVENTIONAL, STANDARD 422 HP D-off $657,508 132.86 21.89 33.91 4.93 42.71 953
LOADING, 33 CY, 37 TON, 14' CUT WIDTH,
4X4 - SINGLE POWERED, TRACTOR
EQUIPPED WITH ATI RUBBER
TRACKS
S20 SCRAPERS, TANDEM POWERED

SUBCATEGORY 0.00 SCRAPERS, TANDEM POWERED

S20CA001 627-G SCRAPER, TANDEM POWERED, STANDARD 330 HP D-off 225 HP D-off $516,919 146.30 16.60 25.45 3.87 58.11 791
4X4, D-9 ASSISTED LOADING
S20CA002 627-G PP SCRAPER, TANDEM POWERED, STANDARD 330 HP D-off 225 HP D-off $744,912 175.17 24.39 37.61 5.58 58.11 824
4X4, PUSH-PULL
S20CA003 637-G SCRAPER, TANDEM POWERED, STANDARD 450 HP D-off 250 HP D-off $1,155,734 252.58 37.87 58.42 8.66 73.30 1,084
WIDTH, 4X4, D-10 ASSISTED LOADING
S20CA004 637-G PP SCRAPER, TANDEM POWERED, STANDARD 450 HP D-off 250 HP D-off $1,203,652 258.64 39.51 60.97 9.02 73.30 1,117
WIDTH, 4X4, PUSH-PULL
S20CA005 657-G SCRAPER, TANDEM POWERED, STANDARD 550 HP D-off 400 HP D-off $1,481,363 324.34 48.90 75.60 11.10 99.47 1,516
4X4, D-11 ASSISTED LOADING
2-188
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
S20 CATERPILLAR INC. ( MACHINE DIVISION)

(continued)
S20CA006 657-G PP SCRAPER, TANDEM POWERED, STANDARD 550 HP D-off 400 HP D-off $1,571,477 339.99 51.70 79.85 11.77 99.47 1,550
4X4, PUSH-PULL
S25 SCRAPERS, TRACTOR DRAWN

SUBCATEGORY 0.00 SCRAPERS, TRACTOR DRAWN
DEERE & COMPANY

S25JD001 1510C SCRAPER, TOWED, STANDARD LOADING, $56,903 10.04 2.01 3.16 0.43 0.00 168
11 CY, 17 TON, 10' CUT WIDTH (ADD 460 HP
TRACTOR)
S25JD002 1814C SCRAPER, TOWED, STANDARD LOADING, $73,578 14.31 2.59 4.05 0.56 0.00 213
14 CY, 23 TON, 14' CUT WIDTH (ADD 460HP
TRACTOR)
REYNOLDS INTERNATIONAL, L.P.

S25RI001 14CS10 SCRAPER, TOWED, PIVOT DUMP, 10.7-14 $48,374 8.98 1.85 2.95 0.37 0.00 138
CY, 15 TON, 10' CUT WIDTH (ADD 250 - 300
HP TRACTOR)
S25RI002 17C12 (RG) SCRAPER, TOWED, PIVOT DUMP, 13-17 CY, $54,384 10.13 2.02 3.21 0.41 0.00 170
17 TON, 12' CUT WIDTH (ADD 350 - 400 HP
TRACTOR)
ROME PLOW CO.

S25RM003 R56H SCRAPER, TOWED, 9-12 CY, 12.5 TON, 8.5' $103,788 19.06 3.78 5.97 0.79 0.00 203
CUT WIDTH (ADD 120-165 HP
TRACTOR)
2-189
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
S25 ROME PLOW CO. (continued)

S25RM001 R67H SCRAPER, TOWED, 12-17 CY, 17 TON, 9.9' $137,805 23.90 5.17 8.24 1.05 0.00 238
TRACTOR)
S25RM002 R89H SCRAPER, TOWED, 18-26 CY, 25 TON, 10.8' $203,935 36.79 7.25 11.40 1.55 0.00 382
TRACTOR)
S25RM004 R89HD SCRAPER, TOWED, 18-26 CY, 25 TON, 10.8' $168,731 31.50 5.74 8.91 1.28 0.00 419
TRACTOR)
S30 SCREENING & CRUSHING PLANTS

SUBCATEGORY 0.10 CONVEYORS

S30KB034 12-3050 SCREENING & CRUSHING PLANTS, FEEDER 15 HP E $60,667 11.95 2.89 4.89 0.44 0.93 15
CONVEYOR, 30" WIDE X 50' LONG, 7 CY
HOPPER & 6' FEED, PORTABLE, 500
TPH
TPH
TPH
TPH
2-190
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
S30 KOLBERG - PIONEER, INC (continued)

S30KB001 13-2480 SCREENING & CRUSHING PLANTS, 10 HP E $39,935 7.87 1.88 3.17 0.29 0.62 14
CONVEYOR, STACKING, 24" WIDE X 80'
LONG, PORTABLE, 250 TPH
CONVEYOR, SIDE FOLDING STACKER, 24"
WIDE X 80' LONG, WHEEL MTD, 750
TPH
WIDE X 100' LONG, PORTABLE, 250
TPH
TPH
2-191
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014

TPH
TPH
TPH
TPH
TPH
TPH
CONVEYOR, FIXED HEIGHT STACKER, 24"
TPH
2-192
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014

WIDE X 150' LONG, PORTABLE, 1,500
TPH
WIDE X 150' LONG, PORTABLE, 2,000
TPH
CONVEYOR, ADJUSTABLE HEIGHT RADIAL
STACKER, 24" WIDE X 100' LONG,
PORTABLE, 750 TPH
PORTABLE, 750 TPH
PORTABLE, 750 TPH
PORTABLE, 1,500 TPH
PORTABLE, 1,500 TPH
2-193
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014

PORTABLE, 1,500 TPH
PORTABLE, 2,000 TPH
PORTABLE, 2,000 TPH
PORTABLE, 2,000 TPH
S30KB042 1430-60-25 SCREENING & CRUSHING PLANTS, SURGE 30 HP E $102,881 20.69 5.11 8.74 0.74 1.85 18
BIN, 25CY, BELT FEEDER, & 30" WIDE X 60'
LONG CONVEYOR, PORTABLE, 1,500
TPH
S30KB054 1936-2 SCREENING & CRUSHING PLANTS, SURGE 15 HP E $105,307 19.74 5.24 8.95 0.76 0.93 18
TPH
S30KB053 1436-60-25 SCREENING & CRUSHING PLANTS, SURGE 40 HP E $106,281 22.20 5.27 9.00 0.77 2.47 20
TPH
2-194
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014

TPH
TPH
PUTZMEISTER INC.
S30PU004 TELEBELT TB SCREENING & CRUSHING PLANTS, 400 HP D-off $914,542 208.44 47.30 81.42 6.59 43.28 763
130 CONVEYOR, 18" WIDE X 126' LONG, 3 CY
HOPPER & TREMIE, 4X8, TRUCK MTD, 360
CY/HR
CY/HR
CY/HR
TELSMITH INC.
S30TS001 PTC 24IN X SCREENING & CRUSHING PLANTS, 12 HP E $41,837 8.41 2.02 3.44 0.30 0.74 10
50FT CONVEYOR, TRUSS FRAME, 24" WIDE X 50'
LONG, WHEEL MTD, 300 TPH
2-195
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
S30 TELSMITH INC. (continued)

LONG, WHEEL MTD, 1,000 TPH
SUBCATEGORY 0.20 CRUSHERS - VERTICAL & HORIZONTAL SHAFT IMPACTOR
HEWITT-ROBINS
S30HW001 MODEL 13654V SCREENING & CRUSHING PLANTS, 250 HP E $363,643 55.59 8.77 12.61 2.46 15.44 804
CRUSHER - SHAFT IMPACTOR, 36"X54",
SINGLE ROTOR, 250 TPH, W/3' X 16'
FEEDER/ 4' GRIZZLY/ 24" X 8' REJECTION
CONVEYOR/ & 36" X 37' DISCHARGE END
DELIVERY CONVEYOR, TRAILER MTD (ADD
250 KW GENERATOR)
2-196
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
S30 HEWITT-ROBINS (continued)

S30HW002 MODEL 14866V SCREENING & CRUSHING PLANTS, 350 HP E $490,840 76.07 11.85 17.08 3.31 21.61 1,280
CRUSHER - SHAFT IMPACTOR, 48"X66"
SINGLE ROTOR, 350 TPH, W/4'X16' FEEDER/
6' GRIZZLY/ 30" X 9.5' REJECTION
CONVEYOR/ & 48" X43' DISCHARGE END
350 KW GENERATOR)
S30HW013 MODEL H4832S SCREENING & CRUSHING PLANTS, 450 HP E $435,223 80.15 10.54 15.19 2.94 27.79 600
CRUSHER - SHAFT IMPACTOR,
SECONDARY, 48"X32" HAMMERMILL, 500
TPH, W/3' X 37' FEED CONVEYOR/ 5' X 16'
VIBRATORY HORIZONTAL TRIPLE DECK
SCREEN/ 36"X30' RETURN CONVEYOR/ &
ROTOR LIFT, TRAILER MTD (ADD 450 KW
GENERATOR)

S30KB045 CS-4250 SCREENING & CRUSHING PLANTS, 360 HP D-off $622,654 98.54 15.22 22.04 4.20 38.95 548
CRUSHER - SHAFT IMPACTOR, 42" X 52",
500 TPH, W/18' X 42" VIBRATORY FEEDER/
ADJUSTABLE GRIZZLY/ & BYPASS FEED,
TRAILER MTD
TELSMITH INC.
S30TS009 4246 SCREENING & CRUSHING PLANTS, 300 HP E $330,863 59.30 8.19 11.91 2.23 18.53 595
CRUSHER - SHAFT IMPACTOR, 46'' X 59'',
600 TPH
S30TS010 4856 SCREENING & CRUSHING PLANTS, 400 HP E $490,581 83.35 12.14 17.66 3.31 24.70 942
1,100 TPH
2-197
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
S30 TELSMITH INC. (continued)

S30TS011 6071 SCREENING & CRUSHING PLANTS, 800 HP E $813,764 152.18 20.15 29.30 5.50 49.40 1,950
2,100 TPH
SUBCATEGORY 0.21 CRUSHERS - CONE

S30KB046 1200 LS SCREENING & CRUSHING PLANTS, 272 HP E $435,114 67.46 10.55 15.21 2.94 16.80 810
CRUSHERS - CONE, SECONDARY, 120 TPH
@ 3/8" -> 250 TPH @ 1", 42" X 50" IMPACT
CRUSHER, W/HOPPER/ & 36" X 32' END
210KW GENERATOR)
S30KB047 1400 LS SCREENING & CRUSHING PLANTS, 315 HP E $541,890 81.42 13.25 19.17 3.66 19.45 741
CRUSHERS - CONE, SECONDARY PLANT,
630 TPH @ 1" ->1,050 TPH @ 2.5", 42" X 50"
IMPACT CRUSHER, W/HOPPER/ & 42" X 32'
END DELIVERY CONVEYOR, TRAILER MTD
(INCLUDES GENERATOR)
SUBCATEGORY 0.22 CRUSHERS - JAW
HEWITT-ROBINS
S30HW005 MODEL J1524PF SCREENING & CRUSHING PLANTS, JAW 40 HP E $195,379 18.35 4.69 6.74 1.32 2.47 86
CRUSHER, 15"X24", 21 TPH @ 1" -> 54 TPH
@ 3", W/2.5' X 8' FEEDER/ 2' GRIZZLY/ & 24"
X 20' END DELIVERY CONVEYOR, TRAILER
2-198
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014

S30HW006 MODEL J1536V SCREENING & CRUSHING PLANTS, JAW 100 HP E $325,328 33.22 7.90 11.40 2.20 6.18 128
CRUSHER, 15"X36", 45 TPH @1.5" -> 150
TPH @ 6", W/3' X 14' FEEDER/ 4' GRIZZLY/ &
30" X 31' END DELIVERY CONVEYOR,
GENERATOR)
CRUSHER, 20" X 36", 65 TPH @ 2" -> 223
GENERATOR)
CRUSHER, 21" X 42", 183 TPH @ 4" -> 345
TPH @ 8", W/3.5' X 16' FEEDER/ 4' GRIZZLY/
& 36" X 34' END DELIVERY CONVEYOR,
GENERATOR)
CRUSHER, 22" X 48", 115 TPH @ 2.5" -> 240
48" X 37' END DELIVERY CONVEYOR (ADD
40 KW GENERATOR)
CRUSHER, 24" X 36", 95 TPH @ 2.5" -> 230
GENERATOR)
2-199
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014

CRUSHER, 30" X 42", 200 TPH @ 4" -> 390
TPH @ 8", W/3.5' X 16' FEEDER/ 6' GRIZZLY/
GENERATOR)
CRUSHER, 30" X 48", 340 TPH @ 5" -> 615
GENERATOR)

S30KB055 CS-1536 SCREENING & CRUSHING PLANTS, JAW 245 HP D-off $404,183 59.39 9.85 14.24 2.73 26.51 548
CRUSHER, 15" X 36", 45 TPH @ 1.5" -> 150
TPH @ 6", W/36"' X 14' VIBRATING FEEDER/
ADJUSTABLE GRIZZLY & BYPASS/ HOPPER/
TRAILER MTD, INCLUDES
GENERATOR
S30KB058 1524-2416 SCREENING & CRUSHING PLANTS, JAW 130 HP E $431,451 43.58 10.52 15.22 2.91 8.03 391
DUPLEX PL CRUSHER, 15" X 36", 200 TPH @ 1/4" -> 250
TPH @ 6", W/36" X 14' VIBRATING FEEDER/
SCREEN CONVEYOR/ & TRIPLE VIBRATORY
SCREENS, TRAILER MTD
2-200
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014

CRUSHER, 20" X 36", 65 TPH @ 2" -> 223
GENERATOR
S30KB059 2036-3024 SCREENING & CRUSHING PLANTS, JAW 300 HP E $678,266 77.12 16.57 23.98 4.58 18.53 415
DUPLEX PL CRUSHER, 20" X 36", 270 TPH @ 1/4" -> 320
TPH @ 7", W/36" X 14' RECIPROCATING
PLATE FEEDER/ 12' LONG ADJUSTABLE
GRIZZLY & BYPASS/ HOPPER/ & 18" X 15'
SCREEN CONVEYOR, TRAILER MTD (ADD
300KW GENERATOR)
CRUSHER, 24" X 36", 95 TPH @ 2.5" -> 230
GENERATOR
SUBCATEGORY 0.30 SCREENING PLANT
HEWITT-ROBINS
S30HW014 V-11 6X16FT, SCREENING & CRUSHING PLANTS, 15 HP E $141,663 27.59 7.16 12.28 1.02 0.93 101
DD SCREENING PLANT, 6' X 16' VIBRATORY
SLOPE DOUBLE DECK SCREENS, W/36" X
16.5' UNDER SCREEN CONVEYOR/ 7 CY
HOPPER/ & FEEDER, TRAILER MTD
2-201
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014

S30HW016 V-11 6X20FT, SCREENING & CRUSHING PLANTS, 20 HP E $147,262 29.08 7.45 12.78 1.06 1.24 115
DD SCREENING PLANT, 6' X 20' VIBRATORY
SLOPE DOUBLE DECK SCREENS, W/36" X
S30HW015 V-11 6X16FT, TD SCREENING & CRUSHING PLANTS, 25 HP E $155,447 31.06 7.88 13.52 1.12 1.54 138
SCREENING PLANT, 6' X 16' VIBRATORY
SLOPE TRIPLE DECK SCREENS W/36" X
SLOPE TRIPLE DECK SCREENS W/36" X
HOPPER/ & FEEDER, TRAILER MTD,
SLOPE TRIPLE DECK SCREENS, W/48" X

S30KB048 616 E-3 SCREENING & CRUSHING PLANTS, 85 HP E $190,229 43.00 9.61 16.48 1.37 5.25 280
SCREENING PLANT, 6' X 16', VIBRATORY
SLOPE TRIPLE DECK SCREENS,
W/HOPPER/ 36" X 28.5' FEEDER CONVEYOR/
48" X27' UNDER SCREEN CONVEYOR/ & 24"
X 20' SIDE DELIVERY CONVEYOR, TRAILER
MTD
2-202
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014

S30KB049 620 E-3 SCREENING & CRUSHING PLANTS, 90 HP E $224,547 49.78 10.83 18.41 1.62 5.56 355
SLOPE TRIPLE DECK SCREENS,
W/HOPPER/ 42" X 34' FEEDER CONVEYOR/
60" X 25' UNDER SCREEN CONVEYOR/ & 30"
X 15' SIDE DELIVERY CONVEYOR, TRAILER
MTD
S30KB050 1822 SCREENING & CRUSHING PLANTS, 250 HP E $271,315 73.15 13.86 23.80 1.96 15.44 416
WASHING/SCREENING PLANT, 6' X 16'
VIBRATORY SLOPE TRIPLE DECK
SCREENS, W/HOPPER / 3 PRODUCT
CHUTES/ ONE FINES CHUTE TO 8' X 32'
CLASSIFYING TANK/ 36" DIA X 32' SLOPED
SCREW & CHUTE, TRAILER MTD (ADD
WATER & FEEDER)
S30KB051 1830 SCREENING & CRUSHING PLANTS, 250 HP E $345,290 86.79 17.56 30.14 2.49 15.44 420
WASHING/SCREENING PLANT, 6' X 20'
VIBRATORY SLOPED TRIPLE DECK
SCREENS, W/HOPPER/ 3 PRODUCT
CHUTES/ ONE FINES CHUTE/ 8' X 32'
CLASSIFYING TANK/ & 44" DIA X 32' SLOPED
SCREW & CHUTE, TRAILER MTD (ADD
WATER & FEEDER)
S30KB052 7208-32 S/P SCREENING & CRUSHING PLANTS, 250 HP E $360,408 89.75 18.67 32.13 2.60 15.44 450
CLASSIFYING PLANT (SAND SORT) 8'W X
32'L TANK & 44" DIA SCREW
METSO MINERALS
S30RA002 CV 50D SCREENING & CRUSHING PLANTS, 25 HP D-off $79,353 17.72 4.06 6.98 0.57 2.70 130
GRIZZLY-SINGLE SCREEN, 120 CY/HR,
TRAILER MTD
2-203
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
S30 METSO MINERALS (continued)

S30RA003 CV 90D SCREENING & CRUSHING PLANTS, 49 HP D-off $125,625 29.17 6.40 10.97 0.91 5.30 195
GRIZZLY-SINGLE SCREEN, 200 CY/HR,
TRAILER MTD
S35 SNOW REMOVAL EQUIPMENT

SUBCATEGORY 0.00 SNOW REMOVAL EQUIPMENT
AMERICAN ROAD MACHINERY, INC.

S35AR001 112 SNOW REMOVAL EQUIPMENT, SNOW $5,289 1.15 0.31 0.53 0.04 0.00 15
PLOW, REVERSIBLE (ADD DUMP
TRUCK)
S35AR002 713 SNOW REMOVAL EQUIPMENT, SNOW $7,524 1.64 0.44 0.75 0.06 0.00 20
PLOW, 1-WAY TRIP (ADD DUMP
TRUCK)
S40 SOIL & ROAD STABILIZERS

SUBCATEGORY 0.00 SOIL & ROAD STABILIZERS

S40BO002 MPH-362 R SOIL & ROAD STABILIZER, 12" DEEP X 79" 360 HP D-off $367,443 117.26 17.20 28.74 2.83 42.72 390
RECYCLER WIDE, HYDROSTATIC RECLAIMER/ SOIL
STABILIZER, 4X2
S40BO003 MPH-362 S SOIL & ROAD STABILIZER, 14" DEEP X 79" 360 HP D-off $346,586 113.37 16.21 27.07 2.67 42.72 390
WIDE, HYDROSTATIC RECLAIMER/ SOIL
STABILIZER, 4X2
S40BO004 MPH-362 SDM SOIL & ROAD STABILIZER, 21" DEEP X 79" 360 HP D-off $352,619 114.49 16.50 27.55 2.72 42.72 390
STABILIZER, 4X2
2-204
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014

S40CA001 RR-250B SOIL & ROAD STABILIZER, 12" DEEP X 96" 309 HP D-off $407,562 118.62 19.10 31.91 3.14 36.67 370
STABILIZER, 4X2
S40CA002 SS-250B SOIL & ROAD STABILIZER, 18" DEEP X 96" 309 HP D-off $391,237 114.55 18.28 30.51 3.02 36.67 308
STABILIZER, 4X2
S40CA003 RM-300 SOIL & ROAD STABILIZER, 18" DEEP X 96" 350 HP D-off $338,604 117.81 14.92 24.62 2.61 41.53 518
WIDE, HYDROSTATIC ROAD RECLAIMER/
SOIL STABILIZER, 4X4
S40CA004 RM-500 SOIL & ROAD STABILIZER, 16" DEEP X 96" 540 HP D-off $530,588 177.33 24.15 40.12 4.09 64.08 599
WIDE, HYDROSTATIC ROAD RECLAIMER/
SOIL STABILIZER, 4X4
S45 SPLITTERS, ROCK & CONCRETE

SUBCATEGORY 0.00 SPLITTERS, ROCK & CONCRETE
ELCO INTERNATIONAL INC.

S45DA004 02-2 SPLITTER, ROCK & CONCRETE, 220 TON 80 CFM A $13,560 4.67 1.02 1.81 0.11 0.00 1
SFORCE, 1.75" DIA, SIZE 2, 5 GAL, 12" DEEP
HOLE REQ'D (ADD 80 CFM
COMPRESSOR)
SFORCE, 1.75" DIA, SIZE 9, 5 GAL, 18" DEEP
HOLE REQ'D (ADD 80 CFM
COMPRESSOR)
SFORCE, 1.75" DIA, SIZE 12, 5 GAL, 26"
DEEP HOLE REQ'D (ADD 80 CFM
COMPRESSOR)
2-205
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
T10 TRACTOR BLADES & ATTACHMENTS (including agricultural)

SUBCATEGORY 0.00 TRACTOR BLADES & ATTACHMENTS (including agricultural)

T10CA001 D3-61-9722 TRACTOR ATTACHMENTS, BLADE, POWER $14,544 2.66 0.69 1.16 0.11 0.00 22
ANGLE, HYDRAULIC, FOR D3, 1.65 CY (ADD
D3 TRACTOR)
T10CA002 D3-PA 30B TRACTOR ATTACHMENTS, POWER WINCH, $18,011 3.28 0.86 1.44 0.14 0.00 21
W/250' CABLE, FOR D3 (ADD D3
TRACTOR)
D4 TRACTOR)
T10CA005 D4-PA 30B TRACTOR ATTACHMENTS, POWER WINCH, $18,011 3.28 0.86 1.44 0.14 0.00 21
W/250' CABLE, FOR D4 (ADD D4
TRACTOR)
T10CA007 D5 N - ANGLE TRACTOR ATTACHMENTS, BLADE, POWER $24,450 4.43 1.17 1.96 0.19 0.00 26
BLADE ANGLE, HYDRAULIC, FOR D5, 2.53 CY (ADD
D5 TRACTOR)
T10CA008 D5-PA 50 TRACTOR ATTACHMENTS, POWER WINCH, $27,429 4.94 1.31 2.19 0.21 0.00 26
FOR D5 (ADD D5 TRACTOR)
T10CA009 D6-108-3970 TRACTOR ATTACHMENTS, BLADE, $29,645 5.34 1.42 2.37 0.23 0.00 57
STRAIGHT, HYDRAULIC, FOR D6, 5.09 CY
(ADD D6 TRACTOR)
D6 TRACTOR)
T10CA011 D6-PA56 WINCH TRACTOR ATTACHMENTS, POWER WINCH, $45,667 8.18 2.18 3.65 0.35 0.00 27
W/CABLE, FOR D6 (ADD D6 TRACTOR)
2-206
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
T10 CATERPILLAR INC. ( MACHINE DIVISION)

(continued)
T10CA012 D7-S TRACTOR ATTACHMENTS, BLADE, $43,717 7.85 2.09 3.50 0.34 0.00 77
(ADD D7 TRACTOR)
T10CA013 D7-U TRACTOR ATTACHMENTS, BLADE, $47,996 8.60 2.29 3.84 0.37 0.00 86
UNIVERSAL, HYDRAULIC, FOR D7, 10.09 CY
(ADD D7 TRACTOR)
T10CA014 D7-A TRACTOR ATTACHMENTS, BLADE, POWER $39,881 7.16 1.91 3.19 0.31 0.00 78
D7 TRACTOR)
T10CA015 D7-PA57 WINCH TRACTOR ATTACHMENTS, POWER WINCH, $59,964 10.74 2.86 4.80 0.46 0.00 45
W/CABLE, FOR D7 (ADD D7 TRACTOR)
T10CA016 D8-SU TRACTOR ATTACHMENTS, BLADE, $58,195 10.46 2.78 4.66 0.45 0.00 107
(ADD D8 TRACTOR)
(ADD D8 TRACTOR)
T10CA018 D8-A TRACTOR ATTACHMENTS, BLADE, POWER $55,719 10.02 2.66 4.46 0.43 0.00 123
D8 TRACTOR)
T10CA019 D8-PP TRACTOR ATTACHMENTS, BLADE, PUSH $1,591 0.33 0.08 0.13 0.01 0.00 5
PLATE, FOR D8 (ADD D8 TRACTOR)
T10CA020 D8, PA58VS TRACTOR ATTACHMENTS, POWER WINCH, $59,722 10.75 2.85 4.78 0.46 0.00 50
WINCH W/CABLE, FOR D8 (ADD D8 TRACTOR)
T10CA021 D9-SU TRACTOR ATTACHMENTS, BLADE, SEMI-U, $79,084 14.23 3.78 6.33 0.61 0.00 143
HYDRAULIC, FOR D9, 17.70 CY (ADD D9
TRACTOR)
2-207
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014

(continued)
(ADD D9 TRACTOR)
T10CA023 D9, PA59VS TRACTOR ATTACHMENTS, POWER WINCH, $80,160 14.43 3.83 6.41 0.62 0.00 86
WINCH W/CABLE, FOR D9 (ADD D9 TRACTOR)
T10CA024 D10-SU TRACTOR ATTACHMENTS, BLADE, SEMI-U, $60,558 11.03 2.89 4.84 0.47 0.00 357
ABRASION HYDRAULIC, FOR D10, 24.20 CY (ADD D10
TRACTOR)
ABRASION UNIVERSAL, HYDRAULIC, FOR D10, 28.70
CY (ADD D10 TRACTOR)
T10CA026 D11-SU TRACTOR ATTACHMENTS, BLADE, $115,100 20.84 5.50 9.21 0.89 0.00 367
(ADD D11 TRACTOR)
UNIVERSAL, HYDRAULIC, FOR D11, 45.00
CY (ADD D11 TRACTOR)
DEERE & COMPANY

T10JD001 915 V-RIPPER TRACTOR ATTACHMENTS, DEEP TILLER, $12,654 2.50 0.58 0.95 0.10 0.00 17
5x7 V SHAPED, 175" WIDE, 7 SHANKS (ADD
200HP TRACTOR W/PTO)
2-208
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
T15 TRACTORS, CRAWLER (DOZER) (includes blade)

SUBCATEGORY 0.01 0 THRU 225 HP

T15CA002 D-3K LGP TRACTOR, CRAWLER (DOZER), 70 HP, LOW 70 HP D-off $115,221 32.85 4.99 8.07 0.95 8.31 175
GROUND PRESSURE, W/2.0 CY SEMI-U
BLADE (ADD ATTACHMENTS)
T15CA020 D-4K XL TRACTOR, CRAWLER (DOZER), 80 HP, 80 HP D-off $122,638 35.69 5.30 8.58 1.01 9.49 181
POWERSHIFT, W/2.18 CY SEMI-U BLADE
(ADD ATTACHMENTS)
GROUND PRESSURE, W/2.39 CY SEMI-U
T15CA021 D-5G XL TRACTOR, CRAWLER (DOZER), 90 HP, 90 HP D-off $138,824 40.34 6.00 9.72 1.14 10.68 195
POWERSHIFT, W/2.85 CY POWER ANGLE
GROUND PRESSURE, W/3.04 CY POWER
ANGLE BLADE (ADD ATTACHMENTS)
T15CA024 D-5K XL TRACTOR, CRAWLER (DOZER), 110 HP, 110 HP D-off $131,617 41.62 5.69 9.21 1.08 13.05 277
(ADD ATTACHMENTS)
T15CA008 D-6N PS XL FTC TRACTOR, CRAWLER (DOZER), 145 HP, 145 HP D-off $262,219 72.78 11.34 18.36 2.16 17.21 321
(ADD ATTACHMENTS)
T15CA023 D-6T TRACTOR, CRAWLER (DOZER), 165 HP, 165 HP D-off $321,405 87.44 13.89 22.50 2.64 19.58 519
LOW GROUND PRESSURE, POWERSHIFT,
W/5.09 CY SEMI-U BLADE (ADD
ATTACHMENTS)
2-209
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014

(continued)
T15CA009 D-6T WHA TRACTOR, CRAWLER (DOZER), 165 HP, 165 HP D-off $394,888 102.26 17.07 27.64 3.25 19.58 519
W/14.3 CY BLADE, TRASH/WASTE
HANDLING ARRANGEMENT
T15CA011 D-6T LGP TRACTOR, CRAWLER (DOZER), 165 HP, 185 HP D-off $388,480 103.70 16.79 27.19 3.19 21.95 461
LOW GROUND PRESSURE, W/5.09 CY SEMI-
U BLADE (ADD ATTACHMENTS)
CASE CORPORATION
T15CS004 550H WT TRACTOR, CRAWLER (DOZER), 67 HP, 67 HP D-off $114,200 32.21 4.94 7.99 0.94 7.95 146
POWERSHIFT, W/1.90 CY UNIVERSAL
T15CS007 1150H WT TRACTOR, CRAWLER (DOZER), 119 HP, 119 HP D-off $199,422 56.53 8.62 13.96 1.64 14.12 263
POWERSHIFT, W/3.90 CY UNIVERSAL
DEERE & COMPANY

T15JD005 450J LT TRACTOR, CRAWLER (DOZER), 70 HP, 70 HP D-off $95,631 28.89 4.14 6.69 0.79 8.31 155
HYDROSTATIC, W/2.00 CY ANGLE BLADE
(ADD ATTACHMENTS)
T15JD006 450J LGP TRACTOR, CRAWLER (DOZER), 70 HP, 70 HP D-off $97,585 29.28 4.22 6.83 0.80 8.31 165
HYDROSTATIC, LOW GROUND PRESSURE,
W/2.15 CY ANGLE BLADE (ADD
ATTACHMENTS)
T15JD007 650K TRACTOR, CRAWLER (DOZER), 101 HP, 101 HP D-off $149,633 44.01 6.47 10.47 1.23 11.98 185
HYDROSTATIC, W/2.60 CY POWER ANGLE
TILT (PAT) BLADE (ADD
ATTACHMENTS)
2-210
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
T15 DEERE & COMPANY (continued)

T15JD008 750K XLT TRACTOR, CRAWLER (DOZER), 155 HP, 155 HP D-off $243,061 70.26 10.51 17.01 2.00 18.39 317
HYDROSTATIC, W/5.60 CY POWER ANGLE
TILT (PAT) BLADE (ADD
ATTACHMENTS)
T15JD009 750K LGP TRACTOR, CRAWLER (DOZER), 165 HP, 165 HP D-off $253,115 73.67 10.94 17.72 2.08 19.58 365
HYDROSTATIC, LOW GROUND PRESSURE,
W/4.84 CY POWER ANGLE TILT (PAT) BLADE
(ADD ATTACHMENTS)
T15JD010 850K XLT TRACTOR, CRAWLER (DOZER), 187 HP, 187 HP D-off $343,381 94.88 14.84 24.04 2.82 22.19 404
HYDROSTATIC, W/7.44 CY SEMI-U POWER
ANGLE TILT (PAT) BLADE (ADD
ATTACHMENTS)
T15JD011 850K LGP TRACTOR, CRAWLER (DOZER), 205 HP, 205 HP D-off $366,330 101.99 15.83 25.64 3.01 24.33 420
HYDROSTATIC LOW GROUND PRESSURE,
W/7.14 CY SEMI-U POWER ANGLE TITLE
(PAT) BLADE (ADD ATTACHMENTS)
SUBCATEGORY 0.02 226 HP THRU 425 HP

T15CA012 D-7R SERIES II TRACTOR, CRAWLER (DOZER), 240 HP, 240 HP D-off $362,031 95.48 13.70 21.72 2.84 28.48 563
(ADD ATTACHMENTS)
T15CA014 D-7R II LGP TRACTOR, CRAWLER (DOZER), 240 HP, 240 HP D-off $410,344 103.97 15.53 24.62 3.22 28.48 530
LOW GROUND PRESSURE, W/7.70 CY
STRAIGHT BLADE (ADD
ATTACHMENTS)
T15CA016 D-8T TRACTOR, CRAWLER (DOZER), 310 HP, 310 HP D-off $624,869 150.92 23.65 37.49 4.90 36.78 898
(ADD ATTACHMENTS)
2-211
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014

(continued)
T15CA017 D-9T TRACTOR, CRAWLER (DOZER), 410 HP, 410 HP D-off $725,646 181.93 27.46 43.54 5.69 48.65 1,033
(ADD ATTACHMENTS)

T15KM008 D155AX-6 TRACTOR, CRAWLER (DOZER), 310 HP, 310 HP D-off $576,851 142.49 21.83 34.61 4.52 36.78 803
POWERSHIFT, W/11.5 CY SEMI-U
BLADE
SUBCATEGORY 0.03 OVER 425 HP

T15CA018 D-10TQ TRACTOR, CRAWLER (DOZER), 580 HP, 580 HP D-off $1,205,601 244.16 41.18 64.30 9.03 58.70 1,421
(ADD ATTACHMENTS)
T15CA019 D-11TQ TRACTOR, CRAWLER (DOZER), 850 HP, 850 HP D-off $1,957,277 386.50 66.86 104.39 14.66 86.03 2,029
(ADD ATTACHMENTS)
T20 TRACTORS, WHEEL TYPE (DOZER)

SUBCATEGORY 0.00 TRACTORS, WHEEL TYPE (DOZER)

T20CA001 814-FS TRACTOR, WHEEL (DOZER), 240 HP, 240 HP D-off $518,393 92.75 18.91 30.30 3.76 24.29 479
ARTICULATING, 4X4, W/3.77 CY STRAIGHT
BLADE
T20CA002 824-HQ TRACTOR, WHEEL (DOZER), 339 HP, 339 HP D-off $769,666 139.73 27.71 44.23 5.59 34.31 633
BLADE
2-212
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014

(continued)
T20CA003 834-HQ TRACTOR, WHEEL (DOZER), 481 HP, 481 HP D-off $1,185,817 203.82 42.17 67.12 8.61 48.68 902
BLADE
T25 TRACTORS, AGRICULTURAL

SUBCATEGORY 0.10 CRAWLER

T25CA006 CH 65E TRACTOR, AGRICULTURAL, CRAWLER- 267 HP D-off $230,322 74.98 11.51 19.58 1.72 28.89 331
RUBBER TRACK, 267 HP, 3 POINT
HITCH
HITCH
HITCH
SUBCATEGORY 0.20 WHEEL
DEERE & COMPANY

T25JD021 6115R TRACTOR, AGRICULTURAL, WHEEL, 115 HP, 115 HP D-off $95,129 33.97 5.56 9.66 0.73 12.44 55
4X4, PTO, 3 POINT HITCH
T25JD022 6170R TRACTOR, AGRICULTURAL, WHEEL, 170HP, 170 HP D-off $136,112 49.20 8.05 14.01 1.04 18.39 74
2-213
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
T25 DEERE & COMPANY (continued)

T25JD027 5045D TRACTOR, AGRICULTURAL, WHEEL, 45 HP, 45 HP D-off $15,246 8.73 0.81 1.37 0.12 4.87 42
T25JD028 5055D TRACTOR, AGRICULTURAL, WHEEL, 55 HP, 55 HP D-off $16,521 10.20 0.88 1.50 0.13 5.95 39
T25JD029 5055D W/MX6 TRACTOR, AGRICULTURAL, WHEEL, 55 HP, 55 HP D-off $22,445 11.43 1.24 2.13 0.17 5.95 51
MOWER 4X2, PTO, 3 POINT HITCH, WITH 60" HEAVY
DUTY ROTARY MOWER
T25JD030 5065E TRACTOR, AGRICULTURAL, WHEEL, 65 HP, 65 HP D-off $34,042 15.08 1.95 3.37 0.26 7.03 27
T30 TRENCHERS, CHAIN TYPE CUTTER

SUBCATEGORY 0.00 TRENCHERS, CHAIN TYPE CUTTER
DITCH WITCH (THE CHARLES MACHINE WORKS)

T30DW012 RT12 TRENCHER, CHAIN TYPE CUTTER, 36" 16 HP G $9,739 6.22 0.56 0.96 0.08 3.55 10
DEEP X 10" WIDE, WALK BEHIND
T30DW013 RT24 TRENCHER, CHAIN TYPE CUTTER, 48" 22 HP G $12,754 8.40 0.70 1.20 0.10 4.88 11
DEEP X 8" WIDE, WALK BEHIND
2-214
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
T30 DITCH WITCH (THE CHARLES MACHINE

WORKS) (continued)
T30DW014 RT115 TRENCHER, CHAIN TYPE CUTTER, 96" 102 HP D-off $130,579 42.36 7.39 12.72 1.03 11.04 80
DEEP X 16" WIDE, 4X4 (W/BLADE,
BHOE)
DEEP X 12" WIDE, 4X4 (W/DBL PIVOT & H313
TRENCHER)
DEEP X 12" WIDE, 4X4 (W/BLADE)
T30DW018 RT95M TRENCHER, CHAIN TYPE CUTTER, 96" 99 HP D-off $112,795 37.90 6.36 10.94 0.89 10.71 77
T30DW011 HT220 TRENCHER, CHAIN TYPE CUTTER, 96" 220 HP D-off $542,150 151.19 31.39 54.22 4.28 23.80 430
DEEP X 12"-24" WIDE, CRAWLER
(W/BLADE)
T30DW010 RT95H TRENCHER, CHAIN TYPE CUTTER, 96" 99 HP D-off $114,158 39.16 6.16 10.52 0.90 10.71 77
TESMEC USA, INC.

T30TM007 TRS 775 TRENCHER, CHAIN TYPE CUTTER, 4' DEEP 220 HP D-off $502,542 142.08 29.10 50.25 3.97 23.80 450
X 12" WIDE, CRAWLER (W/CRUMBSHOE)
SELF LEVEL, OFFSET
X 18" WIDE, CRAWLER (W/CRUMBSHOE)
SELF LEVEL, OFFSET
2-215
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
T30 TESMEC USA, INC. (continued)

X 26" WIDE, CRAWLER
(W/CRUMBSHOE)
T30TM014 TRS 1475 XHP TRENCHER, CHAIN TYPE CUTTER, 10' DEEP 525 HP D-off $1,358,275 375.60 78.64 135.83 10.72 56.80 1,680
X 26" WIDE, CRAWLER
(W/CRUMBSHOE)
X 42" WIDE, CRAWLER
(W/CRUMBSHOE)
X 42" WIDE, CRAWLER
(W/CRUMBSHOE)

T30VE007 T 455 TRENCHER, CHAIN TYPE CUTTER, 6' DEEP 125 HP D-off $198,221 60.67 11.47 19.82 1.56 13.52 180
X 8"-24" WIDE, CRAWLER,
HYDROSTATIC
T30VE008 T 555 III TRENCHER, CHAIN TYPE CUTTER, 8' DEEP 185 HP D-off $251,897 80.30 14.59 25.19 1.99 20.02 225
HYDROSTATIC
X 10.5"-26" WIDE, CRAWLER,
HYDROSTATIC
HYDROSTATIC
2-216
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
T35 TRENCHERS, WHEEL TYPE CUTTER

SUBCATEGORY 0.00 TRENCHERS, WHEEL TYPE CUTTER
CLEVELAND PACIFIC TRENCHER CO

T35CT001 9624 TRENCHER, WHEEL TYPE CUTTER, 72" 140 HP D-off $263,732 77.55 15.27 26.37 2.08 15.15 170
DEEP X 21.5" WIDE, ROUND BUCKET,
CRAWLER
T35CT002 9600-S TRENCHER, WHEEL TYPE CUTTER, 72" 140 HP D-off $324,655 91.55 18.80 32.47 2.56 15.15 228
DEEP X 24" WIDE, ROUND BUCKET,
CRAWLER
T35CT003 246-FD TRENCHER, WHEEL TYPE CUTTER, 84" 185 HP D-off $364,838 106.23 21.12 36.48 2.88 20.02 320
CRAWLER
CRAWLER
CRAWLER
T35CT004 7036-HD TRENCHER, WHEEL TYPE CUTTER, 84" 102 HP D-off $343,361 91.23 19.88 34.34 2.71 11.04 286
CRAWLER
T35CT007 7036-SD TRENCHER, WHEEL TYPE CUTTER, 84" 102 HP D-off $359,553 94.96 20.82 35.96 2.84 11.04 340
CRAWLER
CRAWLER
2-217
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
T35 CLEVELAND PACIFIC TRENCHER CO

(continued)
T35CT009 7648-SD TRENCHER, WHEEL TYPE CUTTER, 90" 150 HP D-off $537,032 141.52 31.09 53.70 4.24 16.23 445
CRAWLER
CRAWLER
T35CT011 400W-HD TRENCHER, WHEEL TYPE CUTTER, 108" 175 HP D-off $632,970 166.57 36.64 63.30 4.99 18.93 700
CRAWLER
T40 TRUCK OPTIONS

SUBCATEGORY 0.10 CRANES / HOISTS, PERSONNEL & MATERIAL HANDLING
AUTO CRANE CO.

T40AH001 AC8-59 TRUCK OPTIONS, CRANE, HYDRAULIC, 3- $29,455 6.68 1.71 2.95 0.23 0.00 2
ARM ARTICULATING, 3.5 TON, 32' BOOM
(ADD 21,000 GVW TRUCK & FLATBED)
PALFINGER INC.
T40PA007 PK 22002-EH TRUCK OPTIONS, CRANE, HYDRAULIC, 3- $50,958 11.38 2.95 5.10 0.40 0.00 51
2-218
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
T40 PALFINGER INC. (continued)

T40PA001 PC 2700 TRUCK OPTIONS, CRANE, HYDRAULIC, 2- $7,693 1.92 0.45 0.77 0.06 0.00 9
T40PA002 PK 14002-EH TRUCK OPTIONS, CRANE, HYDRAULIC, 3- $40,327 9.04 2.34 4.03 0.32 0.00 35
T40PA004 PK 30002 TRUCK OPTIONS, CRANE, HYDRAULIC, 3- $52,011 11.61 3.01 5.20 0.41 0.00 61
ARM ARTICULATING, 10 TON, 69' BOOM
T40PA005 PK 50002-EH TRUCK OPTIONS, CRANE, HYDRAULIC, 2- $98,163 21.69 5.68 9.82 0.77 0.00 1,072
T40PA006 PK 65002-SH TRUCK OPTIONS, CRANE, HYDRAULIC, 2- $113,534 25.05 6.58 11.35 0.90 0.00 126
ARM ARTICULATING, 22 TON, 82' BOOM
SUBCATEGORY 0.20 DUMP BODY, REAR
GALION DUMP BODIES, INC.

T40GN001 BODY502 TRUCK OPTIONS, DUMP BODY, REAR, 16- $16,755 3.62 1.06 1.88 0.12 0.00 42
PACKAGE 89-F 23.5 CY (W/HOIST) (ADD 36,000 GVW
TRUCK)
MIDLAND MANUFACTURING INC.

T40MY002 KLEENSIDE TRUCK OPTIONS, DUMP BODY, REAR, 7.5 $5,513 1.19 0.35 0.62 0.04 0.00 21
CY, AIR GATE (W/HOIST) (ADD 30,000 GVW
TRUCK)
TRUCK)
2-219
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
T40 MIDLAND MANUFACTURING INC.

(continued)
TRUCK)
TRUCK)
TRUCK)
SUBCATEGORY 0.30 FLATBEDS, WITH SIDES
KNAPHEIDE MANUFACTURING CO.

T40KF011 8' VALUE TRUCK OPTIONS, FLATBED, W/40" SIDE $4,744 0.90 0.28 0.47 0.04 0.00 11
MASTER PLAT RACKS, 8' X 8'
MASTER PLA RACKS, 8' X 10'
MASTER RACKS, 8' X 12'
2-220
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
SUBCATEGORY 0.41 HOIST, ELECTRIC DRIVE
KNAPHEIDE MANUFACTURING CO.

T40KF021 KH-1416L TRUCK OPTIONS, HOIST, ELECTRIC DRIVE, $4,735 1.07 0.28 0.47 0.04 0.00 6
PTO, 10' TO 14', 7-16 TON
T40KF023 KH-1416-EE TRUCK OPTIONS, HOIST, ELECTRIC DRIVE, $3,421 0.75 0.20 0.34 0.03 0.00 6
10' TO 14', 7-16 TON
T40KF024 KH-1627L-EE TRUCK OPTIONS, HOIST, ELECTRIC DRIVE, $4,959 1.07 0.29 0.50 0.04 0.00 10
15' TO 20', 14-37 TON
T40KF022 KH-2538L TRUCK OPTIONS, HOIST, ELECTRIC DRIVE, $8,453 1.84 0.50 0.85 0.07 0.00 15
PTO, 20' TO 24', 20-45 TON
SUBCATEGORY 0.50 TRANSIT MIXERS
T40XX034 RDTM-8 TRANSIT MIXER, 8 CY, HYDROSTATIC, 100 235 HP D-on $159,725 67.20 9.71 16.97 1.22 29.50 266
GAL, (INCLUDES 60,000 GVW TRUCK)
2-221
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
SUBCATEGORY 0.60 WATER TANKS

T40RS001 DS 2000 TRUCK OPTIONS, WATER TANK, 2,000 GAL $31,582 5.83 1.74 2.96 0.26 0.00 38
(ADD 28,000 GVW TRUCK)
SUBCATEGORY 0.70 ALL OTHER OPTIONS
ARROW-MASTER, INC.
T40AG001 1350T TRUCK OPTIONS, GUILLOTINE CONCRETE 80 HP D-off $91,948 28.66 5.17 8.88 0.73 8.66 100
BREAKER, W/8'' DIA BREAKING TOOL AND
CAB
T45 TRUCK TRAILERS

SUBCATEGORY 0.10 BOTTOM DUMP

T45MY004 40' MC 2000 TRUCK TRAILER, BOTTOM DUMP, 21 CY, 28 $32,991 6.69 1.40 2.31 0.24 0.00 152
TON, 40' - 2 AXLE, CLAMSHELL (ADD
TOWING TRUCK)
T45MY005 40' TC 3000 TRUCK TRAILER, BOTTOM DUMP, 21 CY, 30 $45,050 9.09 1.85 3.06 0.32 0.00 138
TOWING TRUCK)
TOWING TRUCK)
2-222
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
T45 MIDLAND MANUFACTURING INC.

(continued)
TOWING TRUCK)
T45XX001 TRUCK TRAILER, BOTTOM DUMP, 22.5 CY, $41,975 8.17 1.96 3.31 0.30 0.00 122
27 TON (ADD TOWING TRUCK)
T45XX003 TRUCK TRAILER, BOTTOM DUMP, 25 CY, 30 $50,532 9.66 2.40 4.08 0.36 0.00 160
TON (ADD TOWING TRUCK)
SUBCATEGORY 0.20 END DUMP

T45MY015 28' SK2000 TRUCK TRAILER, END DUMP, 28 CY, 36 $35,633 7.08 1.53 2.54 0.26 0.00 115
TON, 28' - 2 AXLE (W/HOIST) (ADD TOWING
TRUCK)
T45MY016 32' ST 2400 TRUCK TRAILER, END DUMP, 28 CY, 36 $36,220 7.18 1.56 2.60 0.26 0.00 130
TRUCK)
T45MY017 39' SK 2300 TRUCK TRAILER, END DUMP, 39 CY, 50 $39,974 8.14 1.59 2.60 0.29 0.00 170
TRUCK)
T45XX008 TRUCK TRAILER, END DUMP, 20 CY, 24 TON $34,599 6.71 1.57 2.64 0.25 0.00 110
(ADD TOWING TRUCK)
2-223
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
SUBCATEGORY 0.30 PUP TRAILER

T45MY018 14' SK 2100 TRUCK TRAILER, PUP TRAILER, 10 CY, 13 $23,955 5.68 1.12 1.87 0.18 0.00 80
TRUCK)
T45MY019 14' SL 2100 TRUCK TRAILER, PUP TRAILER, 12 CY, 15 $23,758 5.64 1.10 1.84 0.18 0.00 80
TRUCK)
T45XX009 TRUCK TRAILER, PUP TRAILER, 8 CY, LONG $31,586 7.10 1.72 2.97 0.23 0.00 86
TONGUE (ADD TOWING TRUCK)
T45XX010 TRUCK TRAILER, PUP TRAILER, 10 CY, $34,970 7.79 1.94 3.35 0.26 0.00 86
LONG TONGUE (ADD TOWING
TRUCK)
T45XX032 TRUCK TRAILER, PUP TRAILER, 13 CY, 14.5 $42,575 9.36 2.50 4.35 0.32 0.00 92
TON, 3 AXLE (ADD TOWING TRUCK)
T45XX033 TRUCK TRAILER, PUP TRAILER, 16 CY, 18.0 $52,553 11.55 3.05 5.32 0.39 0.00 100
TON, 4 AXLE (ADD TOWING TRUCK)
SUBCATEGORY 0.41 LOWBOY, RIGID NECK, DROP DECK
EAGER BEAVER
T45EA006 35GSL-BR TRUCK TRAILER, LOWBOY, 35 TON, 2 AXLE, $48,019 8.78 2.10 3.50 0.35 0.00 171
DETATCHABLE GOOSENECK (ADD TOWING
TRUCK)
T45EA007 50GSL/3 TRUCK TRAILER, LOWBOY, 50 TON, 3 AXLE , $65,003 11.84 2.78 4.62 0.47 0.00 205
DETATCHABLE GOOSENECK (ADD TOWING
TRUCK)
2-224
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
T45XX011 TRUCK TRAILER, LOWBOY, 25 TON, 2 AXLE $34,939 6.21 1.62 2.73 0.25 0.00 95
(ADD TOWING TRUCK)
(ADD TOWING TRUCK)
(ADD TOWING TRUCK)
(ADD TOWING TRUCK)
(ADD TOWING TRUCK)
(ADD TOWING TRUCK)
(ADD TOWING TRUCK)
(ADD TOWING TRUCK)
(ADD TOWING TRUCK)
(ADD TOWING TRUCK)
(ADD TOWING TRUCK)
(ADD TOWING TRUCK)
(ADD TOWING TRUCK)
2-225
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
SUBCATEGORY 0.50 FLATBED TRAILER
T45XX025 TRUCK TRAILER, FLATBED, 25 TON, 2 AXLE $32,984 5.68 1.49 2.50 0.24 0.00 110
(ADD TOWING TRUCK)
T45XX034 32 TRUCK TRAILER, FLATBED, 40 TON, 2 AXLE $32,439 5.89 1.46 2.45 0.23 0.00 103
(ADD TOWING TRUCK)
T45XX035 40 TRUCK TRAILER, FLATBED, 40 TON, 2 AXLE $34,475 6.20 1.57 2.63 0.25 0.00 110
(ADD TOWING TRUCK)
SUBCATEGORY 0.60 MISCELLANEOUS / UTILITY
T45XX026 TRUCK TRAILER, MISCELLANEOUS/UTILITY, $18,656 3.51 0.86 1.45 0.13 0.00 62
TILT BED, 12 TON, 2 AXLE (ADD TOWING
TRUCK)
TRUCK)
TRUCK)
ATTACHMENT, HELPER DOLLY, 60 TON
TRAILER MAX (ADD TOWING TRUCK)
SUBCATEGORY 0.70 WATER TANKER TRAILER
T45XX029 TRUCK TRAILER, WATER TANKER, 4,000 63 HP D-off $86,955 20.74 3.84 6.29 0.69 6.82 170
GAL, W/PUMP (ADD TOWING TRUCK)
2-226
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
T45 NO SPECIFIC MANUFACTURER

(continued)
SUBCATEGORY 0.90 TANK TRAILERS
GRACO, INC.
T45G1001 28' TRAILER, FOAM SPRAY RIG, 40 KW 75 HP D-off $111,105 26.75 5.05 8.33 0.88 8.11 160
GOOSENECK GENERATOR, AIR COMPESSOR, 410' HOSE,
ETC.
T45G1002 16' TRAILER TRAILER, FOAM SPRAY RIG, 40 KW 75 HP D-off $55,367 17.82 2.52 4.15 0.44 8.11 140
GENERATOR, AIR COMPESSOR, 160' HOSE,
ETC.
T50 TRUCKS, HIGHWAY (Add attachments as required)

SUBCATEGORY 0.01 0 THRU 10,000 GVW
GMC AND CHEVROLET

T50GM001 S10 TRUCK, HIGHWAY, 3,500 GVW, 4X2 120 HP G $18,363 10.98 1.00 1.72 0.14 6.32 26
(COMPACT)
T50GM004 R26 TRUCK, HIGHWAY, 8,600 GVW, 4X2 285 HP G $40,906 25.36 2.31 3.97 0.32 15.00 50
(SUBURBAN)
T50GM005 V26 TRUCK, HIGHWAY, 8,600 GVW, 4X4 285 HP G $43,990 26.02 2.49 4.28 0.35 15.00 52
(SUBURBAN)
2-227
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
T50XX001 4X2 1/2 130 TRUCK, HIGHWAY, CONVENTIONAL, 1/2 130 HP G $17,681 11.45 0.95 1.62 0.14 6.84 45
CONV GAS TON PICKUP, 4X2
T50XX003 4X2 1 180 TRUCK, HIGHWAY, CONVENTIONAL, 1 TON 180 HP G $24,149 15.72 1.34 2.29 0.19 9.48 41
CONV GAS PICKUP, 4X2
T50XX006 4X4 1 180 TRUCK, HIGHWAY, CONVENTIONAL, 1 TON 180 HP G $25,897 16.11 1.44 2.47 0.20 9.48 41
CONV GAS PICKUP, 4X4
T50XX007 4X2 1/2 130 TRUCK, HIGHWAY, CREW, 1/2 TON PICKUP, 130 HP G $18,677 11.66 1.01 1.72 0.15 6.84 45
CREW GAS 4X2
CREW GAS 4X2
T50XX009 4X2 1 180 TRUCK, HIGHWAY, CREW, 1 TON PICKUP, 180 HP G $27,669 16.46 1.55 2.65 0.22 9.48 45
CREW GAS 4X2
CREW GAS 4X4
CREW GAS 4X4
T50XX012 4X4 1 180 TRUCK, HIGHWAY, CREW, 1 TON PICKUP, 180 HP G $28,481 16.64 1.59 2.73 0.22 9.48 45
CREW GAS 4X4
T50XX013 4X2 1/2 75 TRUCK, HIGHWAY, CONVENTIONAL, 1/2 75 HP D-on $22,983 7.22 1.26 2.15 0.18 2.13 39
CONV DSL TON PICKUP, 4X2
2-228
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014

(continued)
T50XX015 4X2 1 130 TRUCK, HIGHWAY, CONVENTIONAL, 1 TON 130 HP D-on $29,388 10.25 1.64 2.82 0.23 3.69 43
CONV DSL PICKUP, 4X2
T50XX018 CONV DSL 4X4 TRUCK, HIGHWAY, CONVENTIONAL, 1 TON 130 HP D-on $33,082 11.03 1.86 3.19 0.26 3.69 49
1 130 PICKUP, 4X4
T50XX019 4X2 3/4 130 TRUCK, HIGHWAY, CREW, 3/4 TON PICKUP, 130 HP D-on $26,420 9.62 1.48 2.53 0.21 3.69 47
CREW DSL 4X2
T50XX020 4X4 3/4 130 TRUCK, HIGHWAY, CREW, 3/4 TON PICKUP 130 HP D-on $31,953 10.77 1.80 3.09 0.25 3.69 55
CREW DSL 4X4
T50XX021 4X2 1 130 TRUCK, HIGHWAY, CREW, 1 TON PICKUP, 130 HP D-on $29,014 10.17 1.62 2.78 0.23 3.69 48
CREW DSL 4X2
SUBCATEGORY 0.02 OVER 10,000 THRU 30,000 GVW (Chassis only - Add options)
T50XX023 4X2 20KGVW TRUCK, HIGHWAY, 20,000 LBS GVW, 2 AXLE, 210 HP G $45,606 36.12 2.07 3.44 0.35 25.27 70
GAS 4X2 (CHASSIS ONLY-ADD OPTIONS)
T50XX024 4X2 25KGVW TRUCK, HIGHWAY, 25,000 LBS GVW, 2 AXLE, 210 HP G $39,625 35.16 1.79 2.96 0.31 25.27 72
GAS 4X2 (CHASSIS ONLY-ADD OPTIONS)
T50XX022 4X2 25KGVW TRUCK, HIGHWAY, 25,000 LBS GVW, 2 AXLE, 180 HP D-on $57,879 23.34 2.66 4.42 0.45 12.39 88
DSL 4X2 (CHASSIS ONLY-ADD OPTIONS)
2-229
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014

(continued)
DSL 4X2, WITH 3-ARM ARTICULATING CRANE,
3.5 TON, 32' BOOM, WITH 8' X 20'
FLATBED
SUBCATEGORY 0.03 OVER 30,000 GVW (Chassis only - Add options)
T50XX032 4X2 35KGVW DUMP TRUCK, HIGHWAY, 35,000 LBS GVW, 265 HP D-on $133,761 47.36 5.35 8.65 1.02 25.76 160
DSL 2 AXLE, 4X2 WITH REAR 10 - 13 CY DUMP
BODY
T50XX033 6X4 75KGVW DUMP TRUCK, HIGHWAY, 75,000 LBS GVW, 400 HP D-on $145,210 63.85 5.74 9.27 1.10 38.88 240
DSL 3 AXLE, 6X4 WITH REAR 16 - 20 CY DUMP
BODY
2-230
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
T55 TRUCKS, OFF-HIGHWAY

SUBCATEGORY 0.10 RIGID FRAME

T55CA007 770 TRUCK, OFF-HIGHWAY, RIGID FRAME, 31.7 487 HP D-off $677,212 112.29 18.31 27.00 4.81 28.89 668
CY, 41.6 TON, 4X4, REAR DUMP
T55CA002 773F TRUCK, OFF-HIGHWAY, RIGID FRAME, 46.9 650 HP D-off $893,056 140.53 23.92 35.14 6.35 38.56 872
CY, 57.7 TON, 4X4, REAR DUMP
T55CA003 777G TRUCK, OFF-HIGHWAY, RIGID FRAME, 78.6 938 HP D-off $1,296,220 210.79 33.60 48.77 9.21 55.65 1,419
CY, 100 TON, 4X4, REAR DUMP

T55KM009 HD325-6A TRUCK, OFF-HIGHWAY, RIGID FRAME, 31.4 488 HP D-off $499,078 94.97 13.27 19.43 3.55 28.95 707
T55KM012 HD785-5 TRUCK, OFF-HIGHWAY, RIGID FRAME, 78.7 1,042 HP D-off $1,027,279 191.61 25.97 37.34 7.30 61.82 1,542
T55KM013 HD1500-5 TRUCK, OFF-HIGHWAY, RIGID FRAME, 102 1,486 HP D-off $2,375,559 349.74 64.79 95.81 16.88 88.16 5,500
T55KM014 730E TRUCK, OFF-HIGHWAY, RIGID FRAME, 145 2,000 HP D-off $2,806,887 432.80 76.09 112.29 19.94 118.66 7,150
SUBCATEGORY 0.20 ARTICULATED FRAME

T55CA014 725 TRUCK, OFF-HIGHWAY, ARTICULATED 214 HP D-off $383,527 72.45 15.34 25.08 2.80 17.92 424
FRAME, 18 CY, 25 TON, 6X6, REAR
DUMP
2-231
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014

(continued)
DUMP
DUMP
T55CA017 735B TRUCK, OFF-HIGHWAY, ARTICULATED 355 HP D-off $599,787 115.15 23.98 39.22 4.37 29.73 667
DUMP
DUMP
DEERE & COMPANY

T55JD001 250D-11 TRUCK, OFF-HIGHWAY, ARTICULATED 265 HP D-off $382,586 82.95 14.58 23.58 2.79 22.20 355
DUMP
T55JD002 300D-11 TRUCK, OFF-HIGHWAY, ARTICULATED 285 HP D-off $424,990 90.63 16.28 26.35 3.10 23.87 401
DUMP
T55JD003 370E TRUCK, OFF-HIGHWAY, ARTICULATED 380 HP D-off $568,594 129.53 20.77 33.24 4.15 31.83 571
FRAME, 26.8 CY, 37 TON, 6X6, REAR
DUMP
T55JD004 410E TRUCK, OFF-HIGHWAY, ARTICULATED 413 HP D-off $616,950 135.10 23.19 37.38 4.50 34.59 635
FRAME, 29.7 CY, 41 TON, 6X6, REAR
DUMP
2-232
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014

T55KM015 HM350-2 TRUCK, OFF-HIGHWAY, ARTICULATED 389 HP D-off $394,996 106.32 13.83 21.89 2.88 32.58 630
FRAME, 19.1-25.9 CY, 35.7 TON, 6 X 6 X 2,
REAR DUMP
T55KM016 HM400-2 TRUCK, OFF-HIGHWAY, ARTICULATED 430 HP D-off $500,096 120.49 18.52 29.74 3.65 36.02 668
FRAME, 21.6-29.2 CY, 40.3 TON, 6 X 6 X 2,
REAR DUMP
VOLVO CONSTRUCTION EQUIPMENT GROUP

T55VO002 A-25E 4X4 TRUCK, OFF-HIGHWAY, ARTICULATED 299 HP D-off $389,755 89.65 14.57 23.45 2.84 25.04 429
FRAME, 14-18 CY, 25 TON, 4X4, REAR
DUMP
T55VO003 A-25E TRUCK, OFF-HIGHWAY, ARTICULATED 299 HP D-off $411,005 89.95 15.72 25.43 3.00 25.04 475
DUMP
DUMP
DUMP
DUMP
2-233
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
T56 TRUCKS,OFF-HIGHWAY/PRIME MOVER TRACTORS & WAGONS

SUBCATEGORY 0.10 PRIME MOVER TRACTORS

T56CA006 776D TRUCK, OFF-HIGHWAY, RIGID FRAME, 938 HP D-off $1,441,841 235.75 37.72 54.96 10.24 62.20 1,164
PRIME MOVER TRACTOR, 4X4
T57 TRUCKS, VACUUM

SUBCATEGORY 0.00 TRUCKS, VACUUM
WASTEQUIP CUSCO INDUSTRIES

T57CU001 INDUSTRIAL TRAILER, VACUUM, 5,500 GAL, 750 CFM, 76 HP D-off $125,715 31.73 5.97 9.99 0.97 8.22 76
VAC 130 REAR DOOR & HYDRAULIC DUMP
SYSTEM
T57CU002 SS INDUST. TRAILER, VACUUM, 5,500 GAL, 750 CFM, 76 HP D-off $154,452 36.79 7.34 12.29 1.19 8.22 76
VAC 130 STAINLESS STEEL, REAR DOOR &
HYDRAULIC DUMP SYSTEM
T57CU003 2127 TRUCK, VACUUM, 3,500 GAL, 2,100 CFM, 300 HP D-off $132,089 60.03 6.27 10.50 1.02 32.46 115
REAR DOOR & HYDRAULIC DUMP SYSTEM
(ADD TRUCK COST)
(ADD TRUCK COST)
(ADD TRUCK COST)
2-234
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
T60 TRUCKS, WATER, OFF-HIGHWAY

SUBCATEGORY 0.00 TRUCKS, WATER, OFF-HIGHWAY
KLEIN PRODUCTS, INC.

T60KI001 KT-50 TRUCK, WATER, OFF-HIGHWAY, 5,000 GAL, 330 HP D-off $466,159 107.19 18.61 30.13 3.54 35.70 320
W/CAT 621G TRACTOR
W/CAT 621G TRACTOR
W/CAT 631G TRACTOR
W/CAT 631G TRACTOR
T60KI006 KT-140 TRUCK, WATER, OFF-HIGHWAY, 14,000 GAL, 564 HP D-off $990,917 219.51 38.43 61.80 7.53 61.02 1,097
W/CAT 651G TRACTOR

T60SO001 STT-60 TRUCK, WATER, OFF-HIGHWAY, 6,000 GAL, 330 HP D-off $510,716 120.51 19.44 31.12 3.88 35.70 610
W/CAT 621E TRACTOR
W/CAT 631E TRACTOR
W/CAT 631E TRACTOR
T60SO004 STT-120 TRUCK, WATER, OFF-HIGHWAY, 12,000 GAL, 550 HP D-off $897,821 207.44 34.28 54.91 6.82 59.50 1,149
W/CAT 651E TRACTOR
T60SO005 STT-140 TRUCK, WATER, OFF-HIGHWAY, 14,000 GAL, 550 HP D-off $912,916 209.50 34.90 55.91 6.94 59.50 1,184
W/CAT 651E TRACTOR
2-235
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
T65 TUNNEL/MINING EQUIPMENT

SUBCATEGORY 0.10 DRIFTING & TUNNELING DRILLS
ATLAS COPCO WAGNER

T65WG012 L2C TUNNELING DRILL, 2 BOOM, 560-1,120 SF 158 HP E 156 HP D-off $1,797,674 271.22 67.22 108.34 13.05 15.28 520
CROSS SECTION, RUBBER TIRED (ADD
DRILL BITS AND DRILL STEEL COST)
T65WG013 WL2C TUNNELING DRILL, 4 BOOM, 700-1,600 SF 158 HP E 156 HP D-off $2,703,511 395.68 101.29 163.34 19.62 15.28 728
T65WG014 WL4C TUNNELING DRILL, 4 BOOM, 700-1,650 SF 380 HP E 224 HP D-off $2,950,150 457.14 110.57 178.31 21.41 33.57 1,058
W25 WATER & CO2 BLASTERS

SUBCATEGORY 0.10 LOW PRESSURE, (< 5,000 PSI)
SIOUX STEAM CLEANER CORPORATION

W25SD006 S1.7 D250 WATER BLASTER, LOW PRESSURE, STEAM 1 HP E $6,059 7.23 0.66 1.21 0.05 0.09 4
CLEANER, 100 GPH, 250 PSI, 1.7 GPM
W25SD007 S2 D250 WATER BLASTER, LOW PRESSURE, STEAM 1 HP E $6,452 8.44 0.71 1.29 0.06 0.09 5
CLEANER, 120 GPH, 250 PS, 2.0 GPM
W25SD008 S2.7 D250 WATER BLASTER, LOW PRESSURE, STEAM 1 HP E $7,015 9.72 0.76 1.40 0.06 0.09 6
CLEANER, 160 GPH, 250 PSI, 2.7 GPM
W25SD001 C-4-E 2000 WATER BLASTER, LOW PRESSURE, COLD 5 HP E $5,685 3.56 0.62 1.14 0.05 0.45 4
WATER, 2,000 PSI, 4 GPM
W25SD005 C-4-G 2800 WATER BLASTER, LOW PRESSURE, COLD 12 HP G $6,658 7.69 0.73 1.33 0.06 3.88 4
2-236
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
W25 SIOUX STEAM CLEANER CORPORATION

(continued)
W25SD003 C-5-G 3400 WATER BLASTER, LOW PRESSURE, COLD 18 HP G $8,826 10.95 0.97 1.77 0.08 5.82 5
W25SD004 H3.5*3000 WATER BLASTER, LOW PRESSURE, HOT 8 HP G $12,938 9.38 1.37 2.52 0.11 2.59 6
WATER, 3,000 PSI, 3.5 GPM, TRAILER
MTD
W25SD009 SF11 WATER BLASTER, LOW PRESSURE, STEAM 11 HP E $15,574 15.40 1.70 3.11 0.14 0.99 9
GENERATOR, 15 PSI, 355 LB/HR STEAM, 55
GAL BOILER
W25SD002 EN-140-H4-1800 WATER BLASTER, LOW PRESSURE, HOT 3 HP E $14,701 7.92 1.60 2.94 0.13 0.27 7
WATER, 1,800 PSI, 2.3 GPM
W25XX005 COLD 3/1000G WATER BLASTER, LOW PRESSURE, COLD 5 HP G $2,107 2.87 0.23 0.42 0.02 1.62 4
WATER, 700 PSI, 3 GPM
W25XX009 HOT 4/1000G WATER BLASTER, LOW PRESSURE, HOT 8 HP G $8,324 7.12 0.90 1.66 0.07 2.59 6
WATER/STEAM, 1,000 PSI, 4 GPM
W25XX010 HOT 6/3000G WATER BLASTER, LOW PRESSURE, HOT 24 HP G $12,743 15.09 1.39 2.55 0.11 7.76 10
WATER/STEAM, 3,000 PSI, 6 GPM
2-237
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
SUBCATEGORY 0.20 HIGH PRESSURE, (>= 5,000 PSI)
NLB CORPORATION
W25NL001 6200E WATER BLASTER, HIGH PRESSURE, 6,000 200 HP E $77,615 67.75 8.44 15.52 0.68 18.05 118
PSI, 50 GPM, SKID MTD, W/MODEL 10200
PUMP
W25NL003 201536D WATER BLASTER, HIGH PRESSURE, 20,000 150 HP D-off $84,145 71.82 9.15 16.83 0.73 23.56 78
PSI, 13.2 GPM, SKID MTD, W/50 LF HOSE &
CLEANING LANCE
PSI, 22 GPM, SKID MTD (ADD TRUCK,
FLATBED TRAILER & WATER
TANKER)
PSI, 53 GPM, SKID MTD (ADD TRUCK,
FLATBED TRAILER & WATER
TANKER)
W25NL004 4400 WATER BLASTER, HIGH PRESSURE, 34 HP D-off $173,231 98.36 18.42 33.82 1.51 5.34 80
HYDRODEMOLITION UNIT, CONCRETE
BUSTER, SELF PROPELLED (ADD MODEL
20600D WATER BLASTER)
SUBCATEGORY 0.30 STEAM CLEANERS
ALKOTA CLEANING SYSTEMS, INC.

W25AO002 122 WATER BLASTER, STEAM CLEANER, 400 1 HP E $4,542 3.21 0.50 0.91 0.04 0.09 4
PSI, 1.7 GPM
PSI, 3.0 GPM
PSI, 4.0 GPM
2-238
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
W25 ALKOTA CLEANING SYSTEMS, INC.

(continued)
PSI, 5.0 GPM
W25AO006 246 WATER BLASTER, STEAM GENERATOR, 100 1 HP E $10,191 6.10 1.11 2.04 0.09 0.09 7
PSI, 1.0 GPM
SUBCATEGORY 0.40 CO2 BLASTERS
COLD JET
W25CJ001 P750B CARBON DIOXIDE (CO2) 20 HP E $80,851 28.37 6.05 10.78 0.66 1.33 34
BLASTER/PELLETIZER, 600 LBS/HR, SINGLE
HOSE DELIVERY (ADD 65-100 CFM
COMPRESSOR)
BLASTER/PELLETIZER, 1,200 LBS/HR,
SINGLE HOSE DELIVERY (ADD 65-150 CFM
COMPRESSOR)
BLASTER/PELLETIZER, 1,200 LBS/HR, DUAL
HOSE DELIVERY (ADD 65-200 CFM
COMPRESSOR)
SUBCATEGORY 0.50 WET ABRASIVE BLASTING SYSTEM (TORBO)
KEIZER TECHNOLOGIES AMERICAS, INC

W25KZ001 TORBO M120 WATER BLASTER, WET ABRASIVE 350 CFM A $22,677 2.66 0.93 1.47 0.19 0.00 4
BLASTER, 4.2 CF TANK CAP, 170 PSI,
(INCLUDES HOSES & NOZZLE, ADD 350 CFM
AIR COMPRESSOR)
2-239
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
W25 KEIZER TECHNOLOGIES AMERICAS, INC

(continued)
BLASTER, 4.2 CF TANK CAP, 170 PSI, W/MIX
RUST INHIBITOR INJECTOR (INCLUDES
HOSES & NOZZLE, ADD 350 CFM AIR
COMPRESSOR)
W25KZ003 LOC WATER BLASTER, WET ABRASIVE 350 CFM A $25,670 3.02 1.06 1.67 0.22 0.00 4
RESTORATION BLASTER, 4.2 CF TANK CAP, 170 PSI,
UNIT W/LOC RESTORATION UNIT (INCLUDES
HOSES & NOZZLE, ADD 350 CFM AIR
COMPRESSOR)
AIR COMPRESSOR)
W25KZ005 TORBO XL320 WATER BLASTER, WET ABRASIVE 385 CFM A $43,109 5.06 1.76 2.80 0.36 0.00 8
AIR COMPRESSOR)
AIR COMPRESSOR)
W/MIX RUST INHIBATOR
INJECTOR,(INCLUDES HOSES & NOZZLE,
ADD 385 CFM AIR COMPRESSOR)
2-240
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
W30 WATER TANKS

SUBCATEGORY 0.10 PORTABLE WITH WHEELS

W30SO001 EWT-8C WATER TANK, PORTABLE, TRAILER MTD, 8 HP G $56,256 9.42 2.22 3.58 0.43 1.77 130
SELF ELEVATING, 8,000 GAL, 10" PIPE
SELF ELEVATING, 10,000 GAL, 10"
PIPE
SELF ELEVATING, 12,000 GAL, 10"
PIPE
SUBCATEGORY 0.20 SKID MOUNTED

W30SO004 WST-8 WATER TANK, PORTABLE, SKID MTD, 8,000 $35,827 4.26 1.47 2.39 0.27 0.00 107
GAL, 10" PIPE
GAL, 10" PIPE
GAL, 10" PIPE
W35 WELDERS
SUBCATEGORY 0.10 ENGINE DRIVEN
W35XX020 GAS 150 AC WELDER, ENGINE DRIVEN, GAS, AC, 150 11 HP G $2,637 3.83 0.15 0.25 0.02 2.98 2
AMP, 4.5 KW, PORTABLE, SKID MTD
2-241
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
W35 NO SPECIFIC MANUFACTURER

(continued)
W35XX021 GAS 225 AC/DC- WELDER, ENGINE DRIVEN, GAS, AC/DC-CC, 17 HP G $6,962 6.50 0.38 0.63 0.06 4.60 6
CC 225 AMP, 5-8 KW, TRAILER MTD
W35XX022 GAS 250 AC/DC- WELDER, ENGINE DRIVEN, GAS, AC/DC- 18 HP G $7,175 6.83 0.39 0.65 0.06 4.87 6
CC/CV CC/CV, 250 AMP, 9 KW, TRAILER MTD
W35XX023 GAS 300 DC-CC WELDER, ENGINE DRIVEN, GAS, DC-CC, 300 45 HP G $12,376 15.97 0.67 1.14 0.10 12.18 14
AMP, 3 KW, TRAILER MTD
W35XX024 DIESEL 400 DC- WELDER, ENGINE DRIVEN, DIESEL, DC- 48 HP D-off $18,274 10.77 1.00 1.69 0.15 6.37 21
CC/CV CC/CV, 400 AMP, 2-10 KW, TRAILER
MTD
W35XX025 DIESEL 500 DC- WELDER, ENGINE DRIVEN, DIESEL, DC- 42 HP D-off $17,542 9.74 0.95 1.62 0.14 5.57 18
CC/CV CC/CV, 500 AMP, 4 KW, TRAILER MTD
SUBCATEGORY 0.20 ELECTRIC DRIVEN
LINCOLN ELECTRIC COMPANY

W35LC021 Tomahawk 1000 WELDER, ELECTRIC DRIVEN, 60 AMP, 20 HP E $2,903 1.50 0.22 0.39 0.02 0.57 1
PLASMA CUTTER WITH 25' HAND
TORCH
W35LC018 SP-180T WELDER, ELECTRIC DRIVEN, 30-180 AMP, 5 HP E $808 0.39 0.07 0.11 0.01 0.14 1
WIRE FEEDER
W35LC012 IDEAL ARC WELDER, ELECTRIC DRIVEN, 400 AMP, 35 HP E $4,607 2.50 0.35 0.61 0.04 1.00 5
R3R-400 STICK
W35LC013 IDEAL ARC WELDER, ELECTRIC DRIVEN, 500 AMP, 41 HP E $4,945 2.83 0.37 0.66 0.04 1.17 5
R3R-500 STICK
2-242
EP 1110-1-8, Vol. 2
30 Apr 14
Table 2-2. Hourly Rate Elements
This Table Contains All Hourly Rate Elements as
Described in Chapter 2
For
Average and Severe Operating Conditions.
Refer to Chapter 2, Section II. Operating Condition
2-253
2-243
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14
4/30/2014 Table 2-2 . HOURLY RATE ELEMENTS
REGION 2 AVERAGE OPERATING CONDITIONS SEVERE OPERATING CONDITIONS
TIRE TIRE TOTAL TIRE TIRE TOTAL

CAT ID. NO. DEPR FCCM FUEL FOG WEAR REPAIR REPAIR RATE DEPR FCCM FUEL FOG WEAR REPAIR REPAIR RATE
A10
A10AR001 0.45 0.03 0.00 0.00 0.00 0.00 0.36 0.84
A10AR002 2.16 0.13 0.00 0.20 0.00 0.00 1.76 4.25
A10RS003 11.62 0.95 18.04 1.87 0.74 0.11 11.90 45.23
A10RS004 11.69 0.95 18.04 1.87 0.74 0.11 11.97 45.37
A10RS005 11.74 0.96 18.04 1.87 0.74 0.11 12.03 45.49
A10RS006 11.78 0.96 18.04 1.87 0.74 0.11 12.06 45.56
A10RS007 11.92 0.97 18.04 1.87 0.74 0.11 12.20 45.85
A10RS008 23.35 1.88 24.33 2.52 0.98 0.15 23.87 77.08
A10SE001 1.71 0.10 0.00 0.00 0.00 0.00 1.39 3.20
A10SE002 2.00 0.12 0.00 0.00 0.00 0.00 1.63 3.75
A15
A15DP001 1.64 0.16 7.04 0.85 0.11 0.02 1.72 11.54
A15DP002 3.62 0.35 13.82 1.67 0.11 0.02 3.78 23.37
A15DP003 4.76 0.47 21.86 2.65 0.18 0.03 4.98 34.93
A15DP004 4.76 0.47 21.86 2.65 0.18 0.03 4.98 34.93
A15DP010 15.03 1.46 50.26 6.09 0.36 0.06 15.70 88.96
A15DP011 6.37 0.62 21.74 2.63 0.12 0.02 6.65 38.15
A15DP012 9.77 0.95 33.92 4.11 0.27 0.04 10.21 59.27
A15DP013 9.77 0.95 33.92 4.11 0.27 0.04 10.21 59.27
A15DP014 16.27 1.59 38.32 4.64 0.50 0.08 17.01 78.41
A15DP015 8.09 0.79 38.32 4.64 0.27 0.04 8.46 60.61
A15SR002 12.31 1.21 55.28 6.70 0.54 0.08 12.88 89.00
A15SR004 1.01 0.10 9.80 1.19 0.11 0.02 1.07 13.30
A15SR005 1.38 0.14 10.05 1.22 0.11 0.02 1.45 14.37
A15SR006 1.01 0.10 9.55 1.16 0.11 0.02 1.07 13.02
A15SR007 1.02 0.10 9.67 1.17 0.11 0.02 1.07 13.16
2-244
2 192
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14
Table 2-2 . HOURLY RATE ELEMENTS 4/30/2014

A15 cont.
A15SR008 2.36 0.23 15.45 1.87 0.18 0.03 2.47 22.59
A15SR009 2.36 0.23 15.58 1.89 0.18 0.03 2.47 22.74
A15SR010 5.07 0.50 28.90 3.50 0.36 0.06 5.32 43.71
A15SR011 6.00 0.59 37.69 4.57 0.36 0.06 6.29 55.56
A15SR012 5.90 0.58 37.69 4.57 0.36 0.06 6.19 55.35
A15SR013 10.58 1.04 56.54 6.85 0.36 0.06 11.06 86.49
A15SR014 11.42 1.13 56.54 6.85 0.78 0.12 11.98 88.82
A15XX019 0.87 0.09 7.67 1.06 0.11 0.02 0.92 10.74
A15XX020 1.71 0.17 3.77 0.46 0.11 0.02 1.79 8.03
A15XX021 1.18 0.12 12.78 1.77 0.11 0.02 1.24 17.22
A15XX022 1.76 0.17 4.40 0.53 0.11 0.02 1.84 8.83
A15XX023 1.24 0.12 16.62 2.30 0.11 0.02 1.30 21.71
A15XX024 1.98 0.20 6.28 0.76 0.11 0.02 2.08 11.43
A15XX025 1.36 0.14 15.34 2.12 0.11 0.02 1.43 20.52
A15XX026 2.22 0.22 8.79 1.07 0.11 0.02 2.33 14.76
A15XX027 1.41 0.14 23.01 3.18 0.11 0.02 1.48 29.35
A15XX028 2.28 0.22 10.05 1.22 0.11 0.02 2.39 16.29
A15XX029 1.53 0.15 17.90 2.48 0.11 0.02 1.61 23.80
A15XX030 3.03 0.30 10.68 1.29 0.11 0.02 3.17 18.60
A15XX031 4.45 0.43 13.82 1.67 0.11 0.02 4.65 25.15
A15XX032 4.03 0.40 14.45 1.75 0.18 0.03 4.21 25.05
A15XX033 5.30 0.53 21.36 2.59 0.36 0.06 5.56 35.76
A15XX034 7.42 0.73 31.41 3.81 0.36 0.06 7.77 51.56
A15XX035 7.92 0.78 34.55 4.19 0.36 0.06 8.29 56.15
A15XX036 8.55 0.84 34.55 4.19 0.36 0.06 8.94 57.49
A15XX037 9.15 0.90 38.95 4.72 0.36 0.06 9.57 63.71
A15XX038 13.97 1.36 45.23 5.48 0.36 0.06 14.59 81.05
2-245
2 193
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

A15 cont.
A15XX039 14.55 1.42 57.79 7.00 0.52 0.08 15.21 96.57
A15XX040 15.70 1.54 62.82 7.61 0.52 0.08 16.42 104.69
A15XX041 0.27 0.03 0.36 0.18 0.00 0.00 0.23 1.07
A15XX042 0.35 0.04 0.50 0.24 0.00 0.00 0.30 1.43
A15XX043 0.41 0.04 0.71 0.35 0.00 0.00 0.35 1.86
A15XX044 0.49 0.05 1.07 0.52 0.00 0.00 0.41 2.54
A15XX045 0.87 0.09 1.78 0.87 0.00 0.00 0.74 4.35
A15XX046 0.97 0.10 2.14 1.04 0.00 0.00 0.83 5.08
A20
A20CK001 0.26 0.01 0.00 0.00 0.00 0.00 0.49 0.76
A20CK002 0.15 0.01 0.00 0.00 0.00 0.00 0.28 0.44
A20CK003 0.30 0.02 0.00 0.00 0.00 0.00 0.55 0.87
A20CK005 0.37 0.02 0.00 0.00 0.00 0.00 0.69 1.08
A20CK006 0.19 0.01 0.00 0.00 0.00 0.00 0.34 0.54
A20CK008 0.21 0.01 0.00 0.00 0.00 0.00 0.39 0.61
A20CK010 0.23 0.01 0.00 0.00 0.00 0.00 0.42 0.66
A20CM010 0.71 0.04 0.00 0.06 0.00 0.00 1.32 2.13
A20CM011 0.92 0.05 0.00 0.06 0.00 0.00 1.70 2.73
A20CM012 1.03 0.05 0.00 0.13 0.00 0.00 1.90 3.11
A20CM013 3.54 0.19 0.00 0.28 0.14 0.02 6.59 10.76
A20CM014 3.81 0.22 0.00 0.41 0.51 0.08 7.15 12.18
A20CM015 5.10 0.28 0.00 0.50 0.35 0.05 9.52 15.80
A20CM016 2.61 0.13 0.00 0.30 0.00 0.00 4.84 7.88
A20CM017 0.13 0.00 0.00 0.00 0.00 0.00 0.24 0.37
A20CM018 0.15 0.00 0.00 0.00 0.00 0.00 0.28 0.43
A20CM019 0.21 0.01 0.00 0.00 0.00 0.00 0.41 0.63
A20CM020 0.13 0.00 0.00 0.00 0.00 0.00 0.25 0.38
2-246
2 194
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

A20 cont.
A20WC002 0.20 0.01 0.12 0.20 0.00 0.00 0.38 0.91
A20WC004 0.59 0.03 0.89 0.12 0.00 0.00 1.10 2.73
A20XX001 0.46 0.01 0.00 0.00 0.00 0.00 0.81 1.28
A20XX002 0.53 0.02 0.00 0.00 0.00 0.00 0.94 1.49
A20XX003 0.66 0.02 0.00 0.00 0.00 0.00 1.16 1.84
A20XX004 0.87 0.03 0.00 0.00 0.00 0.00 1.52 2.42
A20XX005 1.23 0.04 0.00 0.00 0.00 0.00 2.15 3.42
A20XX006 1.49 0.05 0.00 0.00 0.00 0.00 2.62 4.16
A20XX007 1.81 0.06 0.00 0.00 0.00 0.00 3.18 5.05
A20XX008 2.42 0.08 0.00 0.00 0.00 0.00 4.24 6.74
A20XX021 0.21 0.01 0.00 0.00 0.00 0.00 0.39 0.61
A20XX022 0.22 0.01 0.00 0.00 0.00 0.00 0.41 0.64
A20XX023 0.23 0.01 0.00 0.00 0.00 0.00 0.43 0.67
A20XX024 0.24 0.01 0.00 0.00 0.00 0.00 0.45 0.70
A20XX025 0.38 0.02 0.00 0.00 0.00 0.00 0.71 1.11
A25
A25RS006 9.91 0.51 0.00 1.16 0.00 0.00 10.15 21.73
A25RS008 11.34 0.58 0.00 1.80 0.00 0.00 11.62 25.34
A25XX001 10.86 0.56 0.00 0.64 0.00 0.00 11.12 23.18
A25XX002 11.40 0.59 0.00 1.51 0.00 0.00 11.68 25.18
A25XX003 11.56 0.60 0.00 2.09 0.00 0.00 11.85 26.10
A30
A30BG003 37.29 2.93 26.58 4.72 5.56 0.85 48.26 126.19
A30BG004 40.02 2.88 13.29 3.11 0.00 0.00 51.08 110.38
A30BG005 42.58 3.06 26.58 4.72 0.00 0.00 54.35 131.29
A30BK011 26.69 2.05 12.70 1.54 3.68 0.56 34.42 81.64
2-247
2 195
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

A30 cont.
A30BK013 32.38 2.44 17.21 2.09 2.85 0.44 41.64 99.05
A30BK015 37.18 2.82 21.83 2.65 3.74 0.57 47.84 116.63
A30BK018 43.19 3.11 21.83 2.65 0.00 0.00 55.13 125.91
A30BK019 30.22 2.20 12.46 1.51 0.47 0.07 38.64 85.57
A30BK020 39.68 2.88 20.53 2.49 0.56 0.09 50.70 116.93
A30BK021 42.02 3.02 20.88 2.53 0.00 0.00 53.64 122.09
A30BK022 30.54 2.31 17.21 2.09 2.85 0.44 39.29 94.73
A30BK023 36.82 2.65 17.21 2.09 0.00 0.00 47.00 105.77
A30BK024 29.72 2.97 19.91 2.41 2.07 0.32 32.47 89.87
A30CA002 28.27 2.18 20.65 2.50 4.34 0.66 36.47 95.07
A30CA007 20.81 2.05 11.58 1.40 0.86 0.13 22.67 59.50
A30CA008 32.91 2.53 26.58 3.22 4.51 0.69 42.43 112.87
A30CA013 29.10 2.09 20.65 2.50 0.00 0.00 37.14 91.48
A30CA016 47.35 3.41 26.58 3.22 0.00 0.00 60.44 141.00
A30CH001 29.26 2.24 13.05 1.58 3.68 0.56 37.71 88.08
A30CH002 32.34 2.44 18.04 2.19 2.85 0.44 41.59 99.89
A30CH003 34.17 2.46 18.04 2.19 0.00 0.00 43.62 100.48
A30CH004 34.05 2.57 18.04 2.19 3.02 0.46 43.79 104.12
A30CH005 37.18 2.81 20.53 2.49 3.58 0.55 47.81 114.95
A30CH006 45.55 3.28 23.73 2.88 0.00 0.00 58.15 133.59
A30GC002 4.23 0.31 2.97 0.36 0.25 0.04 5.42 13.58
A30GC004 6.26 0.45 4.87 0.59 0.00 0.00 8.00 20.17
A30LD001 11.61 1.20 11.90 1.44 1.82 0.28 12.78 41.03
A30MP001 13.69 1.32 8.66 1.05 0.00 0.00 14.86 39.58
A30MP002 15.33 1.48 10.82 1.31 0.00 0.00 16.63 45.57
A30RT001 33.70 3.25 32.46 3.93 0.12 0.02 36.57 110.05
A30RT007 36.09 3.55 32.46 3.93 2.42 0.37 39.32 118.14
2-248
2 196
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

A30 cont.
A30XX001 10.40 1.22 11.13 1.14 1.12 0.17 7.80 32.98
A30XX002 13.08 1.49 11.13 1.14 0.00 0.00 9.76 36.60
A35
A35AE001 0.61 0.04 1.11 2.10 0.09 0.01 0.68 4.64
A35AE002 1.03 0.07 1.11 2.80 0.09 0.01 1.14 6.25
A35AE003 1.30 0.08 1.11 3.15 0.07 0.01 1.43 7.15
A35AE004 1.53 0.10 1.11 4.05 0.07 0.01 1.68 8.55
A35AE005 1.72 0.12 1.11 6.25 0.13 0.02 1.90 11.25
A40
A40CA008 75.31 4.62 90.30 10.94 0.00 0.00 102.14 283.31
A40CA009 86.30 5.29 102.08 12.37 0.00 0.00 117.05 323.09
A40CW001 117.99 7.23 149.20 18.08 0.00 0.00 160.02 452.52
A40RT008 51.36 3.30 51.04 6.18 2.67 0.41 70.33 185.29
A40RT009 54.83 3.36 51.04 6.18 0.00 0.00 74.36 189.77
A40RT010 67.93 4.16 97.37 11.80 0.00 0.00 92.13 273.39
A40RT011 80.07 4.91 109.94 13.32 0.00 0.00 108.60 316.84
A40RT012 95.78 5.87 109.94 13.32 0.00 0.00 129.91 354.82
A45
A45AE001 2.05 0.11 0.00 7.10 0.05 0.01 2.51 11.83
A45AE002 3.19 0.17 0.00 14.25 0.05 0.01 3.91 21.58
A45AE003 7.43 0.39 0.00 16.85 0.05 0.01 9.09 33.82
A45RS001 8.21 0.44 8.66 1.55 0.09 0.01 10.06 29.02
A45RS002 26.75 1.40 26.37 3.70 0.00 0.00 32.67 90.89
A45SE003 6.69 0.36 3.25 2.39 0.15 0.02 8.21 21.07
A45SE004 3.85 0.22 2.88 0.90 0.20 0.03 4.77 12.85
2-249
2 197
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

B10
B10CC007 5.00 0.41 3.99 3.55 0.17 0.03 6.82 19.97
B10CC008 4.99 0.44 36.16 8.50 1.00 0.15 6.92 58.16
B10CC009 6.29 0.57 44.37 9.89 1.76 0.27 8.80 71.95
B10CC010 7.49 0.67 44.37 10.14 1.76 0.27 10.42 75.12
B10CC011 2.38 0.19 1.24 1.60 0.00 0.00 3.23 8.64
B10CC012 2.48 0.20 3.99 1.30 0.00 0.00 3.36 11.33
B10CC013 3.25 0.26 3.99 1.35 0.00 0.00 4.41 13.26
B10CC014 0.74 0.06 0.31 0.65 0.00 0.00 1.00 2.76
B10CL006 32.59 2.65 7.41 5.61 1.13 0.17 44.46 94.02
B10CL015 16.59 1.38 1.85 3.40 1.05 0.16 22.74 47.17
B10CL021 8.79 0.74 2.16 1.05 0.64 0.10 12.07 25.55
B10CL025 30.28 2.41 12.35 6.01 0.30 0.05 41.13 92.53
B10CL027 2.25 0.18 0.00 0.00 0.00 0.00 3.05 5.48
B10CL032 0.46 0.04 0.62 0.30 0.00 0.00 0.62 2.04
B10CL034 0.92 0.07 1.24 0.60 0.00 0.00 1.25 4.08
B10CL036 0.38 0.03 0.49 0.24 0.00 0.00 0.52 1.66
B10CL040 0.53 0.04 1.24 0.60 0.00 0.00 0.72 3.13
B10CL042 0.35 0.03 0.31 0.15 0.00 0.00 0.48 1.32
B10CL045 0.45 0.04 0.62 0.30 0.00 0.00 0.61 2.02
B10EM001 46.13 3.77 5.55 3.27 1.91 0.29 63.00 123.92
B10EM002 2.84 0.26 0.62 1.30 0.48 0.07 3.96 9.53
B10EM003 2.90 0.23 0.00 0.00 0.00 0.00 3.94 7.07
B10KB001 14.67 1.46 5.87 2.86 0.70 0.11 20.02 45.69
B10KB002 26.49 2.60 13.59 6.61 0.79 0.12 36.07 86.27
B10RC006 20.17 1.68 2.81 5.87 1.25 0.19 27.64 59.61
B10RC007 15.52 1.28 0.93 2.95 0.78 0.12 21.23 42.81
B10RC008 26.74 2.16 1.85 3.40 0.78 0.12 36.44 71.49
2-250
2 198
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

B10 cont.
B10RC016 25.13 2.07 4.63 7.75 1.25 0.19 34.36 75.38
B10RC027 16.30 1.29 2.47 3.20 0.00 0.00 22.11 45.37
B10RC028 18.31 1.44 3.71 4.06 0.00 0.00 24.83 52.35
B10RC029 20.68 1.63 4.94 4.90 0.00 0.00 28.05 60.20
B10RC030 22.53 1.78 6.18 6.76 0.00 0.00 30.56 67.81
B10RC031 23.78 1.88 7.41 7.61 0.00 0.00 32.25 72.93
B10RC032 22.09 1.83 3.09 6.00 1.25 0.19 30.25 64.70
B10SN031 7.15 0.65 1.54 2.10 1.23 0.19 9.98 22.84
B10SN032 11.61 1.00 1.85 2.65 1.25 0.19 16.04 34.59
B10SN033 14.82 1.25 1.85 2.40 1.21 0.19 20.39 42.11
B10SN034 16.59 1.39 1.24 2.10 1.25 0.19 22.79 45.55
B10SN035 17.51 1.47 1.85 2.55 1.25 0.19 24.04 48.86
B10SN036 15.51 1.31 2.78 3.10 1.25 0.19 21.33 45.47
B15
B15BM001 5.52 0.36 8.66 1.05 0.00 0.00 5.41 21.00
B15EC001 24.35 1.63 9.43 1.14 0.85 0.13 23.94 61.47
B15EC002 17.61 1.18 10.82 1.31 0.42 0.06 17.31 48.71
B15EC003 23.65 1.56 24.88 3.01 0.12 0.02 23.21 76.45
B15EC004 26.27 1.73 17.26 2.09 0.00 0.00 25.78 73.13
B15MB001 0.97 0.06 0.00 0.10 0.00 0.00 0.95 2.08
B15MB002 1.17 0.08 0.00 0.14 0.00 0.00 1.15 2.54
B15MB003 1.62 0.11 0.00 0.24 0.11 0.02 1.60 3.70
B15MB004 1.88 0.13 3.99 0.41 0.11 0.02 1.86 8.40
B15RS001 4.76 0.32 8.66 1.05 0.13 0.02 4.68 19.62
B15RS005 6.14 0.41 8.66 1.05 0.25 0.04 6.04 22.59
B15TB001 2.58 0.18 4.00 0.48 0.16 0.02 2.54 9.96
B15TB002 2.59 0.18 4.00 0.48 0.16 0.02 2.55 9.98
2-251
2 199
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

B15 cont.
B15WD001 4.28 0.29 8.66 1.05 0.13 0.02 4.20 18.63
B15WD002 4.45 0.30 8.66 1.05 0.13 0.02 4.37 18.98
B20
B20BN001 1.28 0.09 9.76 1.35 0.05 0.01 1.42 13.96
B20BN002 1.74 0.12 18.63 2.58 0.09 0.01 1.92 25.09
B20BN003 2.04 0.14 31.06 4.30 0.08 0.01 2.26 39.89
B20BN005 2.54 0.17 31.50 4.36 0.08 0.01 2.81 41.47
B20BN006 3.16 0.21 31.50 4.36 0.08 0.01 3.49 42.81
B20BN007 3.57 0.25 15.36 1.86 0.25 0.04 3.96 25.29
B20MQ001 3.75 0.25 9.09 1.10 0.02 0.00 4.14 18.35
B20MQ003 5.55 0.37 15.36 1.86 0.08 0.01 6.13 29.36
B20MQ004 7.49 0.51 21.64 2.62 0.30 0.05 8.29 40.90
B20MQ005 60.62 4.04 94.67 12.97 1.16 0.18 66.97 240.61
B25
B25HB001 2.80 0.18 0.00 0.00 0.00 0.00 2.32 5.30 3.44 0.19 0.00 0.00 0.00 0.00 3.27 6.90
B25HB003 3.02 0.20 0.00 0.00 0.00 0.00 2.51 5.73 3.72 0.20 0.00 0.00 0.00 0.00 3.53 7.45
B25HB005 3.16 0.21 0.00 0.00 0.00 0.00 2.62 5.99 3.89 0.21 0.00 0.00 0.00 0.00 3.69 7.79
B25HB007 3.78 0.25 0.00 0.00 0.00 0.00 3.14 7.17 4.65 0.26 0.00 0.00 0.00 0.00 4.42 9.33
B25HB008 3.89 0.26 0.00 0.00 0.00 0.00 3.24 7.39 4.79 0.26 0.00 0.00 0.00 0.00 4.55 9.60
B25HB009 4.07 0.27 0.00 0.00 0.00 0.00 3.39 7.73 5.01 0.28 0.00 0.00 0.00 0.00 4.76 10.05
B25HB010 4.70 0.31 0.00 0.00 0.00 0.00 3.91 8.92 5.79 0.32 0.00 0.00 0.00 0.00 5.50 11.61
B25HB011 4.90 0.32 0.00 0.00 0.00 0.00 4.08 9.30 6.03 0.33 0.00 0.00 0.00 0.00 5.73 12.09
B25HB012 4.98 0.33 0.00 0.00 0.00 0.00 4.14 9.45 6.12 0.34 0.00 0.00 0.00 0.00 5.82 12.28
B25HB013 5.09 0.33 0.00 0.00 0.00 0.00 4.23 9.65 6.26 0.34 0.00 0.00 0.00 0.00 5.95 12.55
B25HB014 5.60 0.37 0.00 0.00 0.00 0.00 4.65 10.62 6.89 0.38 0.00 0.00 0.00 0.00 6.55 13.82
B25HB015 5.77 0.38 0.00 0.00 0.00 0.00 4.80 10.95 7.11 0.39 0.00 0.00 0.00 0.00 6.75 14.25
2-252
2 200
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

B25 cont.
B25XX001 2.01 0.13 0.00 0.00 0.00 0.00 1.67 3.81 2.48 0.14 0.00 0.00 0.00 0.00 2.35 4.97
B25XX002 2.16 0.14 0.00 0.00 0.00 0.00 1.80 4.10 2.66 0.15 0.00 0.00 0.00 0.00 2.53 5.34
B25XX003 2.32 0.15 0.00 0.00 0.00 0.00 1.93 4.40 2.86 0.16 0.00 0.00 0.00 0.00 2.71 5.73
B25XX004 2.48 0.16 0.00 0.00 0.00 0.00 2.06 4.70 3.06 0.17 0.00 0.00 0.00 0.00 2.90 6.13
B25XX005 2.60 0.17 0.00 0.00 0.00 0.00 2.16 4.93 3.20 0.18 0.00 0.00 0.00 0.00 3.04 6.42
B25XX006 3.02 0.20 0.00 0.00 0.00 0.00 2.51 5.73 3.72 0.20 0.00 0.00 0.00 0.00 3.54 7.46
B25XX007 3.14 0.21 0.00 0.00 0.00 0.00 2.61 5.96 3.87 0.21 0.00 0.00 0.00 0.00 3.67 7.75
B25XX008 3.49 0.23 0.00 0.00 0.00 0.00 2.90 6.62 4.30 0.24 0.00 0.00 0.00 0.00 4.09 8.63
B25XX009 4.12 0.27 0.00 0.00 0.00 0.00 3.42 7.81 5.07 0.28 0.00 0.00 0.00 0.00 4.81 10.16
B25XX010 4.35 0.29 0.00 0.00 0.00 0.00 3.61 8.25 5.35 0.29 0.00 0.00 0.00 0.00 5.08 10.72
B25XX011 4.73 0.31 0.00 0.00 0.00 0.00 3.93 8.97 5.82 0.32 0.00 0.00 0.00 0.00 5.53 11.67
B25XX012 5.14 0.34 0.00 0.00 0.00 0.00 4.27 9.75 6.33 0.35 0.00 0.00 0.00 0.00 6.01 12.69
B25XX013 6.10 0.40 0.00 0.00 0.00 0.00 5.07 11.57 7.51 0.41 0.00 0.00 0.00 0.00 7.13 15.05
B25XX014 6.43 0.42 0.00 0.00 0.00 0.00 5.34 12.19 7.91 0.44 0.00 0.00 0.00 0.00 7.51 15.86
B25XX015 6.57 0.43 0.00 0.00 0.00 0.00 5.46 12.46 8.09 0.45 0.00 0.00 0.00 0.00 7.68 16.22
B25XX016 6.84 0.45 0.00 0.00 0.00 0.00 5.69 12.98 8.42 0.46 0.00 0.00 0.00 0.00 8.00 16.88
B25XX017 7.26 0.48 0.00 0.00 0.00 0.00 6.03 13.77 8.93 0.49 0.00 0.00 0.00 0.00 8.49 17.91
B25XX018 7.62 0.50 0.00 0.00 0.00 0.00 6.33 14.45 9.38 0.52 0.00 0.00 0.00 0.00 8.91 18.81
B25XX019 7.88 0.52 0.00 0.00 0.00 0.00 6.55 14.95 9.69 0.53 0.00 0.00 0.00 0.00 9.21 19.43
B30
B30CR001 0.54 0.03 0.00 0.00 0.00 0.00 0.49 1.06
B30CR002 0.61 0.04 0.00 0.00 0.00 0.00 0.55 1.20
B30CR003 0.68 0.04 0.00 0.00 0.00 0.00 0.61 1.33
B30CR004 0.71 0.04 0.00 0.00 0.00 0.00 0.64 1.39
B30CR005 0.89 0.05 0.00 0.00 0.00 0.00 0.80 1.74
B30CR006 1.09 0.07 0.00 0.00 0.00 0.00 0.98 2.14
B30CR009 0.94 0.06 0.00 0.00 0.00 0.00 0.85 1.85
2-253
2 201
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

B30 cont.
B30CR010 1.15 0.07 0.00 0.00 0.00 0.00 1.04 2.26
B30CR011 1.45 0.09 0.00 0.00 0.00 0.00 1.30 2.84
B30CR012 1.70 0.10 0.00 0.00 0.00 0.00 1.53 3.33
B30GB001 0.50 0.03 0.00 0.00 0.00 0.00 0.39 0.92
B30GB002 0.65 0.04 0.00 0.00 0.00 0.00 0.51 1.20
B30GB003 0.80 0.05 0.00 0.00 0.00 0.00 0.63 1.48
B30GB004 1.16 0.07 0.00 0.00 0.00 0.00 0.91 2.14
B30GB005 1.38 0.08 0.00 0.00 0.00 0.00 1.09 2.55
B30GB006 3.12 0.19 0.00 0.00 0.00 0.00 2.63 5.94
B30GB007 3.37 0.20 0.00 0.00 0.00 0.00 2.85 6.42
B30GB008 3.74 0.23 0.00 0.00 0.00 0.00 3.15 7.12
B30GB009 4.14 0.25 0.00 0.00 0.00 0.00 3.49 7.88
B30GB010 5.23 0.32 0.00 0.00 0.00 0.00 4.42 9.97
B30GB011 2.02 0.12 0.00 0.00 0.00 0.00 1.82 3.96
B30GB012 2.09 0.13 0.00 0.00 0.00 0.00 1.88 4.10
B30GB013 2.17 0.13 0.00 0.00 0.00 0.00 1.95 4.25
B30GB014 2.84 0.17 0.00 0.00 0.00 0.00 2.55 5.56
B30GB015 2.94 0.18 0.00 0.00 0.00 0.00 2.64 5.76
B30GB016 4.91 0.30 0.00 0.00 0.00 0.00 4.42 9.63
B30GB017 5.33 0.32 0.00 0.00 0.00 0.00 4.79 10.44
B30GB018 0.39 0.02 0.00 0.00 0.00 0.00 0.31 0.72
B35
B35HE001 0.90 0.06 0.00 0.00 0.00 0.00 0.75 1.71 1.11 0.06 0.00 0.00 0.00 0.00 1.06 2.23
B35HE002 1.06 0.07 0.00 0.00 0.00 0.00 0.88 2.01 1.30 0.07 0.00 0.00 0.00 0.00 1.24 2.61
B35HE003 1.50 0.10 0.00 0.00 0.00 0.00 1.25 2.85 1.85 0.10 0.00 0.00 0.00 0.00 1.75 3.70
B35HE004 1.81 0.12 0.00 0.00 0.00 0.00 1.50 3.43 2.23 0.12 0.00 0.00 0.00 0.00 2.12 4.47
B35HE005 2.07 0.14 0.00 0.00 0.00 0.00 1.72 3.93 2.55 0.14 0.00 0.00 0.00 0.00 2.42 5.11
2-254
2 202
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

B35 cont.
B35HE006 2.59 0.17 0.00 0.00 0.00 0.00 2.15 4.91 3.18 0.18 0.00 0.00 0.00 0.00 3.02 6.38
B35HE007 2.81 0.19 0.00 0.00 0.00 0.00 2.34 5.34 3.46 0.19 0.00 0.00 0.00 0.00 3.29 6.94
B35HE008 3.69 0.24 0.00 0.00 0.00 0.00 3.07 7.00 4.54 0.25 0.00 0.00 0.00 0.00 4.32 9.11
B35HE009 3.87 0.26 0.00 0.00 0.00 0.00 3.22 7.35 4.77 0.26 0.00 0.00 0.00 0.00 4.53 9.56
B35HE010 4.47 0.29 0.00 0.00 0.00 0.00 3.72 8.48 5.51 0.30 0.00 0.00 0.00 0.00 5.23 11.04
B35HE011 4.84 0.32 0.00 0.00 0.00 0.00 4.03 9.19 5.96 0.33 0.00 0.00 0.00 0.00 5.66 11.95
B35HE012 5.30 0.35 0.00 0.00 0.00 0.00 4.40 10.05 6.52 0.36 0.00 0.00 0.00 0.00 6.19 13.07
B35HE013 5.87 0.39 0.00 0.00 0.00 0.00 4.88 11.14 7.23 0.40 0.00 0.00 0.00 0.00 6.86 14.49
B35HE014 6.72 0.44 0.00 0.00 0.00 0.00 5.58 12.74 8.27 0.46 0.00 0.00 0.00 0.00 7.85 16.58
B35HE015 7.30 0.48 0.00 0.00 0.00 0.00 6.07 13.85 8.99 0.49 0.00 0.00 0.00 0.00 8.54 18.02
B35HE016 8.72 0.57 0.00 0.00 0.00 0.00 7.25 16.54 10.73 0.59 0.00 0.00 0.00 0.00 10.20 21.52
B35HE017 10.03 0.66 0.00 0.00 0.00 0.00 8.34 19.03 12.35 0.68 0.00 0.00 0.00 0.00 11.73 24.76
B35HE018 0.87 0.06 0.00 0.00 0.00 0.00 0.72 1.65 1.12 0.07 0.00 0.00 0.00 0.00 1.06 2.25
B35HE019 0.99 0.07 0.00 0.00 0.00 0.00 0.83 1.89 1.28 0.07 0.00 0.00 0.00 0.00 1.21 2.56
B35HE020 1.42 0.10 0.00 0.00 0.00 0.00 1.18 2.70 1.82 0.11 0.00 0.00 0.00 0.00 1.73 3.66
B35HE021 1.79 0.13 0.00 0.00 0.00 0.00 1.49 3.41 2.30 0.13 0.00 0.00 0.00 0.00 2.19 4.62
B35HE022 2.06 0.15 0.00 0.00 0.00 0.00 1.72 3.93 2.65 0.16 0.00 0.00 0.00 0.00 2.52 5.33
B35HE023 2.47 0.18 0.00 0.00 0.00 0.00 2.05 4.70 3.17 0.19 0.00 0.00 0.00 0.00 3.01 6.37
B35HE024 2.72 0.20 0.00 0.00 0.00 0.00 2.26 5.18 3.50 0.21 0.00 0.00 0.00 0.00 3.32 7.03
B35HE025 3.53 0.26 0.00 0.00 0.00 0.00 2.93 6.72 4.53 0.27 0.00 0.00 0.00 0.00 4.31 9.11
B35HE026 3.60 0.26 0.00 0.00 0.00 0.00 2.99 6.85 4.63 0.27 0.00 0.00 0.00 0.00 4.40 9.30
B35HE027 4.36 0.32 0.00 0.00 0.00 0.00 3.62 8.30 5.60 0.33 0.00 0.00 0.00 0.00 5.32 11.25
B35HE028 4.51 0.33 0.00 0.00 0.00 0.00 3.75 8.59 5.79 0.34 0.00 0.00 0.00 0.00 5.50 11.63
B35HE029 5.20 0.38 0.00 0.00 0.00 0.00 4.32 9.90 6.68 0.39 0.00 0.00 0.00 0.00 6.35 13.42
B35HE030 5.73 0.42 0.00 0.00 0.00 0.00 4.76 10.91 7.36 0.43 0.00 0.00 0.00 0.00 6.99 14.78
B35HE031 6.97 0.51 0.00 0.00 0.00 0.00 5.79 13.27 8.96 0.53 0.00 0.00 0.00 0.00 8.51 18.00
B35HE032 7.42 0.54 0.00 0.00 0.00 0.00 6.17 14.13 9.55 0.56 0.00 0.00 0.00 0.00 9.07 19.18
2-255
2 203
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

B35 cont.
B35HE033 9.46 0.69 0.00 0.00 0.00 0.00 7.86 18.01 12.16 0.71 0.00 0.00 0.00 0.00 11.55 24.42
B35HE034 10.54 0.77 0.00 0.00 0.00 0.00 8.76 20.07 13.55 0.79 0.00 0.00 0.00 0.00 12.88 27.22
B35HE035 2.91 0.23 0.00 0.00 0.00 0.00 2.42 5.56 3.64 0.24 0.00 0.00 0.00 0.00 3.46 7.34
B35HE036 3.04 0.24 0.00 0.00 0.00 0.00 2.53 5.81 3.80 0.25 0.00 0.00 0.00 0.00 3.61 7.66
B35HE037 3.42 0.27 0.00 0.00 0.00 0.00 2.84 6.53 4.27 0.28 0.00 0.00 0.00 0.00 4.06 8.61
B35HE038 4.64 0.37 0.00 0.00 0.00 0.00 3.86 8.87 5.81 0.38 0.00 0.00 0.00 0.00 5.51 11.70
B35HE039 5.19 0.42 0.00 0.00 0.00 0.00 4.32 9.93 6.49 0.43 0.00 0.00 0.00 0.00 6.17 13.09
B35HE040 5.36 0.43 0.00 0.00 0.00 0.00 4.46 10.25 6.70 0.44 0.00 0.00 0.00 0.00 6.37 13.51
B35HE041 5.74 0.46 0.00 0.00 0.00 0.00 4.77 10.97 7.18 0.47 0.00 0.00 0.00 0.00 6.82 14.47
B35HE042 7.39 0.59 0.00 0.00 0.00 0.00 6.14 14.12 9.24 0.61 0.00 0.00 0.00 0.00 8.77 18.62
B35HE043 7.60 0.61 0.00 0.00 0.00 0.00 6.32 14.53 9.50 0.63 0.00 0.00 0.00 0.00 9.02 19.15
B35HE044 9.88 0.79 0.00 0.00 0.00 0.00 8.21 18.88 12.35 0.81 0.00 0.00 0.00 0.00 11.73 24.89
B35HE045 10.24 0.82 0.00 0.00 0.00 0.00 8.51 19.57 12.80 0.84 0.00 0.00 0.00 0.00 12.16 25.80
B35HE046 12.18 0.98 0.00 0.00 0.00 0.00 10.13 23.29 15.23 1.00 0.00 0.00 0.00 0.00 14.47 30.70
B35HE047 13.00 1.04 0.00 0.00 0.00 0.00 10.80 24.84 16.25 1.07 0.00 0.00 0.00 0.00 15.44 32.76
B35SA001 6.59 0.43 0.00 0.00 0.00 0.00 5.48 12.50 8.12 0.45 0.00 0.00 0.00 0.00 7.71 16.28
B35SA003 9.89 0.65 0.00 0.00 0.00 0.00 8.22 18.76 12.17 0.67 0.00 0.00 0.00 0.00 11.56 24.40
B35SA004 14.84 0.98 0.00 0.00 0.00 0.00 12.33 28.15 18.27 1.01 0.00 0.00 0.00 0.00 17.35 36.63
B35SA005 19.79 1.30 0.00 0.00 0.00 0.00 16.45 37.54 24.36 1.34 0.00 0.00 0.00 0.00 23.14 48.84
B35SA006 24.76 1.63 0.00 0.00 0.00 0.00 20.58 46.97 30.48 1.68 0.00 0.00 0.00 0.00 28.95 61.11
B35SA007 29.68 1.95 0.00 0.00 0.00 0.00 24.67 56.30 36.53 2.01 0.00 0.00 0.00 0.00 34.70 73.24
B35SA008 39.57 2.61 0.00 0.00 0.00 0.00 32.88 75.06 48.70 2.68 0.00 0.00 0.00 0.00 46.26 97.64
B35SA009 49.45 3.26 0.00 0.00 0.00 0.00 41.10 93.81 60.87 3.35 0.00 0.00 0.00 0.00 57.82 122.04
B35SA010 59.35 3.91 0.00 0.00 0.00 0.00 49.33 112.59 73.05 4.02 0.00 0.00 0.00 0.00 69.39 146.46
B35XX001 3.56 0.23 0.00 0.00 0.00 0.00 2.96 6.75 4.38 0.24 0.00 0.00 0.00 0.00 4.17 8.79
B35XX002 4.01 0.26 0.00 0.00 0.00 0.00 3.33 7.60 4.93 0.27 0.00 0.00 0.00 0.00 4.68 9.88
B35XX003 4.43 0.29 0.00 0.00 0.00 0.00 3.68 8.40 5.45 0.30 0.00 0.00 0.00 0.00 5.18 10.93
2-256
2 204
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

B35 cont.
B35XX004 5.05 0.33 0.00 0.00 0.00 0.00 4.20 9.58 6.22 0.34 0.00 0.00 0.00 0.00 5.91 12.47
B35XX005 5.67 0.37 0.00 0.00 0.00 0.00 4.71 10.75 6.98 0.38 0.00 0.00 0.00 0.00 6.63 13.99
B35XX006 6.98 0.46 0.00 0.00 0.00 0.00 5.80 13.24 8.59 0.47 0.00 0.00 0.00 0.00 8.16 17.22
B35XX007 3.58 0.26 0.00 0.00 0.00 0.00 2.98 6.82 4.61 0.27 0.00 0.00 0.00 0.00 4.38 9.26
B35XX008 4.10 0.30 0.00 0.00 0.00 0.00 3.40 7.80 5.27 0.31 0.00 0.00 0.00 0.00 5.00 10.58
B35XX009 4.41 0.32 0.00 0.00 0.00 0.00 3.66 8.39 5.67 0.33 0.00 0.00 0.00 0.00 5.39 11.39
B35XX010 5.24 0.38 0.00 0.00 0.00 0.00 4.36 9.98 6.74 0.40 0.00 0.00 0.00 0.00 6.41 13.55
B35XX011 5.80 0.42 0.00 0.00 0.00 0.00 4.82 11.04 7.46 0.44 0.00 0.00 0.00 0.00 7.08 14.98
B35XX012 7.35 0.54 0.00 0.00 0.00 0.00 6.11 14.00 9.45 0.55 0.00 0.00 0.00 0.00 8.98 18.98
B35XX013 0.82 0.07 0.00 0.00 0.00 0.00 0.68 1.57 1.02 0.07 0.00 0.00 0.00 0.00 0.97 2.06
B35XX014 0.92 0.07 0.00 0.00 0.00 0.00 0.76 1.75 1.15 0.08 0.00 0.00 0.00 0.00 1.09 2.32
B35XX015 1.36 0.11 0.00 0.00 0.00 0.00 1.13 2.60 1.70 0.11 0.00 0.00 0.00 0.00 1.62 3.43
B35XX016 1.55 0.12 0.00 0.00 0.00 0.00 1.29 2.96 1.94 0.13 0.00 0.00 0.00 0.00 1.85 3.92
B35XX017 1.70 0.14 0.00 0.00 0.00 0.00 1.41 3.25 2.12 0.14 0.00 0.00 0.00 0.00 2.01 4.27
B35XX018 3.62 0.29 0.00 0.00 0.00 0.00 3.01 6.92 4.53 0.30 0.00 0.00 0.00 0.00 4.30 9.13
B35XX019 3.86 0.31 0.00 0.00 0.00 0.00 3.21 7.38 4.83 0.32 0.00 0.00 0.00 0.00 4.59 9.74
B35XX020 4.36 0.35 0.00 0.00 0.00 0.00 3.63 8.34 5.45 0.36 0.00 0.00 0.00 0.00 5.18 10.99
B35XX021 4.74 0.38 0.00 0.00 0.00 0.00 3.94 9.06 5.93 0.39 0.00 0.00 0.00 0.00 5.63 11.95
B35XX022 6.00 0.48 0.00 0.00 0.00 0.00 4.98 11.46 7.50 0.49 0.00 0.00 0.00 0.00 7.12 15.11
B35XX023 6.42 0.51 0.00 0.00 0.00 0.00 5.34 12.27 8.03 0.53 0.00 0.00 0.00 0.00 7.63 16.19
C05
C05OL001 0.17 0.00 0.70 0.10 0.00 0.00 0.51 1.48
C05OL002 0.26 0.01 1.43 0.20 0.00 0.00 0.81 2.71
C05OL003 0.32 0.01 1.58 0.22 0.00 0.00 0.98 3.11
C05OL004 0.35 0.01 1.74 0.24 0.00 0.00 1.07 3.41
2-257
2 205
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

C10
C10BO001 0.98 0.03 0.91 0.09 0.00 0.00 1.36 3.37
C10BO003 0.37 0.01 1.22 0.13 0.00 0.00 0.52 2.25
C10BO004 0.44 0.02 1.83 0.19 0.00 0.00 0.61 3.09
C10BO008 3.86 0.13 1.35 0.14 0.00 0.00 5.38 10.86
C10BO009 1.79 0.07 1.22 0.13 0.00 0.00 2.79 6.00
C10BO011 4.70 0.19 1.20 0.12 0.00 0.00 7.32 13.53
C10BO013 10.73 0.43 2.85 0.30 0.00 0.00 16.71 31.02
C10BO015 4.18 0.17 0.75 0.08 0.00 0.00 6.52 11.70
C10BO016 5.24 0.21 1.35 0.14 0.00 0.00 8.16 15.10
C10RX001 7.01 0.28 1.20 0.12 0.00 0.00 10.92 19.53
C10RX002 9.67 0.39 2.10 0.22 0.00 0.00 15.07 27.45
C10RX003 16.17 0.65 4.95 0.51 0.00 0.00 25.18 47.46
C10WC003 0.94 0.03 0.60 0.06 0.00 0.00 1.30 2.93
C10WC006 1.22 0.04 1.68 0.17 0.00 0.00 1.70 4.81
C10WC007 1.86 0.06 2.74 0.28 0.00 0.00 2.59 7.53
C10WC008 3.36 0.12 1.35 0.14 0.00 0.00 4.69 9.66
C10WC010 2.13 0.09 3.35 0.35 0.00 0.00 3.32 9.24
C10WC015 6.66 0.23 2.10 0.22 0.00 0.00 9.28 18.49
C10WC016 7.42 0.30 3.00 0.31 0.00 0.00 11.56 22.59
C10WC017 2.83 0.11 1.35 0.14 0.00 0.00 4.41 8.84
C10WC019 7.04 0.28 3.00 0.31 0.00 0.00 10.96 21.59
C15
C15BL001 1.99 0.09 0.13 0.57 0.00 0.00 2.47 5.25
C15BL003 7.85 0.34 0.67 1.86 0.00 0.00 9.74 20.46
C15BL004 9.02 0.39 1.00 2.29 0.00 0.00 11.19 23.89
C15BL005 12.65 0.55 2.00 3.08 0.00 0.00 15.71 33.99
2-258
2 206
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

C15 cont.
C15BL006 47.07 3.71 54.97 6.66 0.00 0.00 58.43 170.84
C15ED001 1.70 0.07 2.61 0.36 0.00 0.00 2.11 6.85
C15ED002 1.03 0.04 2.13 0.29 0.00 0.00 1.28 4.77
C15XX001 14.27 1.15 30.75 3.73 0.52 0.08 17.77 68.27
C20
C20WC002 2.19 0.11 3.08 0.43 0.26 0.04 2.18 8.29
C20XX001 1.43 0.07 3.08 0.43 0.19 0.03 1.42 6.65
C25
C25AJ001 0.81 0.04 1.42 0.20 0.00 0.00 0.89 3.36
C25AJ003 1.37 0.07 1.42 0.20 0.00 0.00 1.51 4.57
C25AJ004 1.54 0.08 2.13 0.29 0.00 0.00 1.70 5.74
C25AJ005 1.72 0.09 2.61 0.36 0.00 0.00 1.90 6.68
C25AJ006 1.95 0.10 2.61 0.36 0.00 0.00 2.15 7.17
C25AJ007 2.06 0.11 2.61 0.36 0.00 0.00 2.27 7.41
C25AJ008 1.51 0.14 1.22 0.22 0.00 0.00 1.42 4.51
C25AJ009 1.60 0.15 1.22 0.22 0.00 0.00 1.51 4.70
C25AJ010 1.71 0.16 1.22 0.22 0.00 0.00 1.62 4.93
C25AJ011 1.83 0.17 1.22 0.22 0.00 0.00 1.73 5.17
C25AJ012 1.94 0.19 1.22 0.22 0.00 0.00 1.84 5.41
C25AJ013 2.06 0.20 1.22 0.22 0.00 0.00 1.94 5.64
C25AJ015 1.99 0.10 4.74 0.66 0.00 0.00 2.19 9.68
C25AJ016 2.23 0.12 5.69 0.79 0.00 0.00 2.46 11.29
C25AJ018 2.31 0.12 5.69 0.79 0.00 0.00 2.55 11.46
C25AJ019 3.18 0.17 8.05 1.11 0.00 0.00 3.50 16.01
C25ST001 0.45 0.02 1.90 0.26 0.00 0.00 0.49 3.12
C25ST002 0.46 0.02 2.13 0.29 0.00 0.00 0.50 3.40
2-259
2 207
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

C25 cont.
C25SV001 29.09 2.80 7.03 1.15 0.37 0.06 27.58 68.08
C25SV002 27.38 2.63 7.03 1.15 0.30 0.05 25.94 64.48
C25SV003 13.63 1.32 3.25 0.53 0.25 0.04 12.93 31.95
C25WC002 0.56 0.03 1.90 0.26 0.00 0.00 0.62 3.37
C35
C35AF002 1.74 0.14 0.00 2.00 0.04 0.01 2.32 6.25
C35AF004 4.98 0.39 3.77 2.46 0.08 0.01 6.61 18.30
C35AF005 7.22 0.57 6.78 2.82 0.17 0.03 9.61 27.20
C35AL002 4.83 0.39 3.77 1.46 0.24 0.04 6.47 17.20
C35AL003 1.58 0.14 0.36 0.37 0.24 0.04 2.17 4.90
C35AL008 2.95 0.23 0.00 0.30 0.00 0.00 3.91 7.39
C35AL013 1.41 0.12 0.00 0.40 0.12 0.02 1.91 3.98
C35AL014 7.68 0.60 7.66 1.43 0.08 0.01 10.19 27.65
C35AV006 10.21 0.79 1.43 2.70 0.16 0.02 13.55 28.86
C35AV008 3.18 0.24 0.50 2.24 0.00 0.00 4.21 10.37
C35AV009 3.87 0.30 1.14 2.55 0.00 0.00 5.12 12.98
C35AV010 7.22 0.56 1.85 2.90 0.00 0.00 9.55 22.08
C35AV011 5.69 0.44 0.86 2.42 0.00 0.00 7.54 16.95
C35AV012 16.54 1.27 1.43 3.20 0.00 0.00 21.89 44.33
C40
C40CC001 5.22 0.27 0.67 0.36 0.00 0.00 5.76 12.28
C40MU001 0.55 0.03 1.90 0.26 0.05 0.01 0.62 3.42
C40MU002 1.18 0.06 3.08 0.43 0.05 0.01 1.31 6.12
C40MU003 0.55 0.03 1.90 0.26 0.05 0.01 0.61 3.41
C40MU004 0.64 0.04 1.90 0.26 0.05 0.01 0.71 3.61
C40ST001 0.33 0.02 0.03 0.22 0.05 0.01 0.37 1.03
2-260
2 208
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

C40 cont.
C40ST002 0.36 0.02 1.30 0.18 0.05 0.01 0.41 2.33
C40ST003 0.43 0.03 0.13 0.32 0.05 0.01 0.48 1.45
C40ST005 0.58 0.03 0.10 0.35 0.05 0.01 0.65 1.77
C40XX001 0.47 0.02 0.13 0.27 0.00 0.00 0.52 1.41
C40XX002 0.51 0.03 1.66 0.23 0.00 0.00 0.56 2.99
C40XX003 0.68 0.04 0.20 0.31 0.00 0.00 0.75 1.98
C40XX004 0.68 0.04 1.90 0.26 0.00 0.00 0.75 3.63
C40XX005 0.82 0.04 0.33 0.43 0.00 0.00 0.90 2.52
C40XX006 1.58 0.08 0.33 0.43 0.00 0.00 1.74 4.16
C40XX007 1.49 0.08 2.13 0.29 0.00 0.00 1.65 5.64
C45
C45GO010 22.47 1.38 11.56 1.40 0.00 0.00 30.48 67.29
C45GO011 34.65 2.12 23.24 2.82 0.00 0.00 47.00 109.83
C45GO012 46.50 2.85 21.23 2.57 0.00 0.00 63.07 136.22
C45GO013 18.68 1.15 11.56 1.40 0.00 0.00 25.34 58.13
C45GO014 25.73 1.58 12.31 1.49 0.00 0.00 34.89 76.00
C45GO016 50.99 3.13 28.90 3.50 0.00 0.00 69.16 155.68
C45GO018 63.61 3.90 42.09 5.10 0.00 0.00 86.27 200.97
C45GO020 76.08 4.66 56.54 6.85 0.00 0.00 103.19 247.32
C45GO026 8.06 0.49 9.20 1.27 0.00 0.00 10.93 29.95
C45GO027 10.23 0.63 6.28 0.76 0.00 0.00 13.88 31.78
C45GO028 16.30 1.00 6.28 0.76 0.00 0.00 22.11 46.45
C45GO029 10.83 0.66 9.20 1.27 0.00 0.00 14.69 36.65
C45GO031 61.79 3.79 48.37 5.86 0.00 0.00 83.80 203.61
C45MJ001 1.17 0.07 3.84 0.53 0.00 0.00 1.59 7.20
C45MW002 6.71 0.42 3.27 0.40 0.08 0.01 9.11 20.00
C45MW003 8.51 0.53 3.27 0.40 0.12 0.02 11.57 24.42
2-261
2 209
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

C55
C55M3001 2.74 0.18 10.90 1.51 0.08 0.01 3.37 18.79
C55M3002 6.39 0.42 7.12 0.86 0.00 0.00 7.83 22.62
C55M3003 7.29 0.48 12.58 1.52 0.00 0.00 8.95 30.82
C55OE001 32.34 2.13 0.00 0.00 0.00 0.00 39.67 74.14
C55OE002 41.54 2.74 0.00 0.00 0.00 0.00 50.96 95.24
C55OE003 63.30 4.17 0.00 0.00 0.00 0.00 77.65 145.12
C55OE006 6.02 0.40 8.78 1.06 0.07 0.01 7.40 23.74
C55OE009 11.38 0.76 15.07 1.83 0.14 0.02 13.97 43.17
C55OE011 8.30 0.55 21.48 2.60 0.14 0.02 10.19 43.28
C55OE012 13.39 0.89 21.48 2.60 0.14 0.02 16.44 54.96
C55SC001 9.25 0.61 9.49 1.15 0.08 0.01 11.35 31.94
C55SC002 16.00 1.07 23.38 2.83 0.24 0.04 19.66 63.22
C55SC005 53.16 3.55 28.92 3.50 1.04 0.16 65.29 155.62
C55SC006 57.36 3.82 28.92 3.50 1.04 0.16 70.44 165.24
C60
C60HG008 0.15 0.01 0.61 0.08 0.00 0.00 0.19 1.04
C60HG010 0.30 0.02 3.35 0.46 0.00 0.00 0.37 4.50
C60HG011 3.99 0.21 9.90 1.63 0.00 0.00 4.90 20.63
C60HG012 4.20 0.22 9.90 1.63 0.00 0.00 5.15 21.10
C60HG013 4.23 0.22 9.90 1.63 0.00 0.00 5.19 21.17
C60HG014 2.21 0.11 2.57 1.25 0.00 0.00 2.71 8.85
C60HG015 0.91 0.05 6.09 0.84 0.00 0.00 1.12 9.01
C60HG016 5.23 0.27 12.61 2.07 0.00 0.00 6.42 26.60
C60HG020 3.15 0.16 14.62 2.02 0.00 0.00 3.86 23.81
C60HG021 3.80 0.20 14.62 2.02 0.00 0.00 4.66 25.30
C60HG023 2.23 0.11 2.57 1.25 0.00 0.00 2.74 8.90
2-262
2 210
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

C60 cont.
C60HG024 3.79 0.20 14.62 2.02 0.00 0.00 4.65 25.28
C60HG025 0.24 0.01 2.74 0.38 0.00 0.00 0.29 3.66
C60HG026 0.60 0.03 3.96 0.55 0.00 0.00 0.73 5.87
C60LY001 4.35 0.22 3.05 0.42 0.00 0.00 5.34 13.38
C60LY002 6.44 0.33 10.66 1.47 0.00 0.00 7.90 26.80
C60LY005 0.50 0.03 3.96 0.55 0.00 0.00 0.61 5.65
C60LY011 12.43 0.64 4.80 0.79 0.00 0.00 15.25 33.91
C65
C65ST007 0.25 0.01 0.06 0.03 0.00 0.00 0.76 1.11
C65ST008 0.26 0.01 0.12 0.06 0.00 0.00 0.79 1.24
C65ST009 0.30 0.01 0.19 0.09 0.00 0.00 0.94 1.53
C65ST013 0.56 0.02 1.22 0.17 0.00 0.00 1.73 3.70
C65WC003 0.42 0.02 0.12 0.20 0.00 0.00 1.29 2.05
C65WC004 0.27 0.01 0.19 0.23 0.00 0.00 0.83 1.53
C65WC005 0.51 0.02 1.11 0.15 0.00 0.00 1.58 3.37
C75
C75BD004 5.30 0.64 10.74 1.49 0.23 0.04 5.34 23.78
C75BD005 6.55 0.80 17.64 2.44 0.61 0.09 6.61 34.74
C75BD006 9.53 1.17 28.12 3.89 1.01 0.15 9.63 53.50
C75BD007 3.80 0.46 9.72 1.34 0.25 0.04 3.84 19.45
C75BD008 5.08 0.62 10.74 1.49 0.25 0.04 5.12 23.34
C75BD009 6.77 0.83 17.64 2.44 0.61 0.09 6.83 35.21
C75BD010 11.30 1.38 10.68 1.39 1.01 0.15 11.41 37.32
C75BD011 15.08 1.84 16.33 2.12 1.98 0.30 15.22 52.87
C75GV016 86.90 10.74 37.69 4.89 21.47 3.28 87.85 252.82
C75GV023 25.32 3.11 20.10 2.61 5.35 0.82 25.58 82.89
2-263
2 211
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

C75 cont.
C75GV024 33.11 4.10 21.74 2.82 7.47 1.14 33.48 103.86
C75GV029 10.44 1.27 20.45 2.83 0.64 0.10 10.53 46.26
C75GV030 15.96 1.92 25.57 3.54 0.48 0.07 16.08 63.62
C75GV031 39.91 5.02 30.15 3.91 15.05 2.30 40.45 136.79
C75GV032 48.49 6.07 34.55 4.48 16.70 2.56 49.12 161.97
C75TD009 21.75 2.60 22.62 2.93 0.00 0.00 21.88 71.78
C75TD010 28.38 3.39 31.03 4.03 0.00 0.00 28.54 95.37
C75TD011 37.33 4.46 31.03 4.03 0.00 0.00 37.55 114.40
C75TE001 22.48 2.75 16.33 2.12 3.51 0.54 22.69 70.42
C75TE002 30.94 3.79 19.10 2.48 4.72 0.72 31.23 92.98
C80
C80GV006 44.69 6.11 43.28 4.87 1.76 0.27 39.38 140.36 51.07 6.16 57.24 6.45 6.84 1.05 48.25 177.06
C80GV016 127.38 21.55 38.99 4.39 15.67 2.40 144.43 354.81 141.53 21.66 50.17 5.65 62.64 9.58 169.48 460.71
C80GV029 46.30 6.39 48.69 5.48 3.82 0.58 40.86 152.12 52.92 6.44 64.39 7.25 15.23 2.33 50.06 198.62
C80GV030 46.42 6.40 48.69 5.48 3.82 0.58 40.96 152.35 53.06 6.46 64.39 7.25 15.23 2.33 50.20 198.92
C80GV033 54.36 7.50 38.41 4.33 7.83 1.20 47.96 161.59 62.12 7.56 50.80 5.72 31.32 4.79 58.77 221.08
C80GV034 69.75 10.68 43.49 4.90 7.83 1.20 70.29 208.14 78.47 10.76 57.52 6.48 31.32 4.79 84.07 273.41
C80GV035 45.25 6.95 43.49 4.90 3.82 0.58 45.63 150.62 50.91 7.01 57.52 6.48 15.23 2.33 54.57 194.05
C80LB009 32.39 4.44 39.49 4.45 1.66 0.25 28.55 111.23 37.01 4.47 52.23 5.88 6.64 1.02 34.98 142.23
C80LB011 32.69 4.53 39.49 4.45 3.34 0.51 28.87 113.88 37.36 4.57 52.23 5.88 13.25 2.03 35.37 150.69
C80TD001 35.67 5.57 20.16 2.27 5.91 0.90 36.05 106.53 40.12 5.61 25.79 2.90 23.85 3.65 43.12 145.04
C80TD002 44.75 6.94 24.68 2.77 5.73 0.88 45.18 130.93 50.34 7.00 31.72 3.58 22.45 3.43 54.04 172.56
C80TD003 51.92 7.85 24.68 2.77 0.00 0.00 52.22 139.44 58.41 7.91 31.72 3.58 0.00 0.00 62.46 164.08
C80TD004 58.91 9.85 67.86 7.64 0.00 0.00 66.67 210.93 65.45 9.90 88.49 9.97 0.00 0.00 78.23 252.04
C80TD005 48.29 8.29 67.86 7.64 7.25 1.11 54.88 195.32 53.66 8.33 88.49 9.97 28.76 4.40 64.40 258.01
C80TE002 19.86 2.77 27.05 3.05 2.49 0.38 17.55 73.15 22.70 2.79 35.77 4.03 10.06 1.54 21.51 98.40
C80TE003 26.43 3.69 40.03 4.51 3.68 0.56 23.37 102.27 30.21 3.72 52.94 5.96 14.72 2.25 28.63 138.43
2-264
2 212
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

C80 cont.
C80TE008 17.62 2.19 14.06 2.19 5.11 0.78 13.37 55.32 20.56 2.22 18.60 2.90 20.05 3.07 16.92 84.32
C80XX001 8.86 1.11 26.51 4.13 1.53 0.23 6.73 49.10 10.34 1.12 35.06 5.46 6.12 0.94 8.51 67.55
C80XX002 11.69 1.47 32.46 5.06 2.38 0.36 8.88 62.30 13.64 1.48 42.93 6.69 9.61 1.47 11.24 87.06
C85
C85KC005 27.59 4.61 14.12 1.34 0.00 0.00 29.50 77.16 34.49 4.67 18.58 1.77 0.00 0.00 39.03 98.54
C85KC008 52.58 9.62 20.95 2.17 0.00 0.00 62.84 148.16 64.26 9.72 27.57 2.86 0.00 0.00 80.82 185.23
C85KC009 32.53 5.44 18.90 1.80 0.00 0.00 34.79 93.46 40.67 5.51 24.87 2.36 0.00 0.00 46.03 119.44
C85KC010 52.54 8.78 24.07 2.29 0.00 0.00 56.19 143.87 65.67 8.90 31.67 3.01 0.00 0.00 74.33 183.58
C85KC011 68.91 12.61 24.07 2.49 0.00 0.00 82.36 190.44 84.22 12.73 31.67 3.28 0.00 0.00 105.92 237.82
C85LB001 33.76 5.64 16.44 1.56 0.00 0.00 36.10 93.50 42.20 5.72 21.64 2.06 0.00 0.00 47.76 119.38
C85LB014 44.09 7.37 18.83 1.79 0.00 0.00 47.15 119.23 55.11 7.47 24.78 2.36 0.00 0.00 62.37 152.09
C85LB015 61.07 10.21 18.83 1.79 0.00 0.00 65.31 157.21 76.34 10.34 24.78 2.36 0.00 0.00 86.40 200.22
C85LB016 70.76 12.95 18.83 1.95 0.00 0.00 84.57 189.06 86.48 13.08 24.78 2.57 0.00 0.00 108.76 235.67
C85LB019 43.40 6.47 25.77 3.79 0.00 0.00 49.31 128.74 53.41 6.56 33.70 4.95 0.00 0.00 67.83 166.45
C85LB021 61.16 10.20 25.77 2.45 0.00 0.00 77.67 177.25 73.39 10.31 33.70 3.20 0.00 0.00 102.93 223.53
C85LB024 27.75 4.63 13.06 1.13 0.00 0.00 27.82 74.39 33.31 4.68 17.19 1.49 0.00 0.00 35.60 92.27
C85MA002 66.81 11.14 30.85 2.93 0.00 0.00 84.85 196.58 80.17 11.26 40.34 3.83 0.00 0.00 112.44 248.04
C85MA003 87.28 16.09 36.30 3.76 0.00 0.00 122.41 265.84 109.10 16.27 47.46 4.92 0.00 0.00 167.60 345.35
C85MA005 53.26 8.90 22.55 2.14 0.00 0.00 56.96 143.81 66.58 9.02 29.67 2.82 0.00 0.00 75.35 183.44
C85MA006 58.68 10.74 22.55 2.34 0.00 0.00 70.14 164.45 71.72 10.84 29.67 3.07 0.00 0.00 90.20 205.50
C85MA007 79.64 14.57 24.87 2.58 0.00 0.00 95.20 216.86 97.34 14.72 32.72 3.39 0.00 0.00 122.42 270.59
C85MA008 53.35 8.92 22.55 2.14 0.00 0.00 57.06 144.02 66.69 9.04 29.67 2.82 0.00 0.00 75.48 183.70
C85MA011 84.86 14.15 54.44 5.18 0.00 0.00 107.77 266.40 101.83 14.30 71.20 6.77 0.00 0.00 142.81 336.91
C85MA012 79.81 13.34 39.79 3.78 0.00 0.00 85.35 222.07 99.76 13.52 52.35 4.98 0.00 0.00 112.90 283.51
C85TE001 34.66 5.17 13.61 2.00 0.00 0.00 39.38 94.82 42.65 5.24 17.80 2.61 0.00 0.00 54.17 122.47
C85TE002 48.22 7.19 22.69 3.33 0.00 0.00 54.79 136.22 59.35 7.29 29.67 4.36 0.00 0.00 75.37 176.04
C85TE003 54.07 9.02 30.40 2.89 0.00 0.00 68.67 165.05 64.89 9.11 39.75 3.78 0.00 0.00 91.01 208.54
2-265
2 213
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

C85 cont.
C85TE008 30.98 5.18 12.20 1.16 0.00 0.00 33.13 82.65 38.73 5.25 16.05 1.53 0.00 0.00 43.83 105.39
C85TE009 38.20 6.39 15.25 1.45 0.00 0.00 40.85 102.14 47.75 6.47 20.07 1.91 0.00 0.00 54.04 130.24
C85TE010 50.67 8.47 15.91 1.51 0.00 0.00 54.19 130.75 63.34 8.58 20.94 1.99 0.00 0.00 71.68 166.53
C85TE011 68.03 12.45 20.89 2.16 0.00 0.00 81.32 184.85 83.15 12.57 27.48 2.85 0.00 0.00 104.58 230.63
C90
C90LB001 63.54 11.96 25.76 2.90 15.40 2.36 76.73 198.65 70.60 12.02 32.45 3.66 61.56 9.42 90.04 279.75
C90LB003 117.98 22.13 46.28 5.21 23.10 3.53 142.36 360.59 131.09 22.23 58.95 6.64 92.35 14.13 167.06 492.45
C95
C95AP004 24.79 4.13 7.90 8.27 0.00 0.00 28.17 73.26
C95AP005 0.78 0.13 0.00 0.00 0.00 0.00 0.89 1.80
C95AP006 1.46 0.24 0.00 0.00 0.00 0.00 1.66 3.36
C95AP007 39.18 6.53 13.15 12.11 0.00 0.00 44.52 115.49
C95AP008 5.95 0.99 0.00 0.50 0.00 0.00 6.76 14.20
C95AP009 1.97 0.33 0.00 0.00 0.00 0.00 2.24 4.54
C95AP010 52.26 8.71 13.40 12.24 0.00 0.00 59.38 145.99
C95AP011 1.84 0.31 0.00 0.00 0.00 0.00 2.09 4.24
C95AP012 7.43 1.24 0.00 0.50 0.00 0.00 8.44 17.61
C95AP013 50.03 8.34 21.86 16.82 0.00 0.00 56.84 153.89
C95AP014 1.68 0.28 0.00 0.00 0.00 0.00 1.90 3.86
C95AP015 6.48 1.08 0.00 0.50 0.00 0.00 7.36 15.42
C95AP016 2.26 0.38 0.00 0.00 0.00 0.00 2.57 5.21
C95AP017 21.17 3.53 7.72 7.17 0.00 0.00 24.05 63.64
C95AP018 0.70 0.12 0.00 0.00 0.00 0.00 0.79 1.61
C95AP019 4.02 0.67 0.00 0.50 0.00 0.00 4.57 9.76
C95AP020 23.32 3.89 13.77 10.44 0.00 0.00 26.50 77.92
C95AP021 36.46 6.08 15.93 12.61 0.00 0.00 41.43 112.51
2-266
2 214
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

C95 cont.
C95AP022 5.48 0.91 1.48 1.80 0.00 0.00 6.22 15.89
C95AP023 0.13 0.02 0.00 0.00 0.00 0.00 0.15 0.30
C95LH003 21.65 3.61 6.73 6.64 0.00 0.00 24.60 63.23
C95LH005 28.16 4.69 9.14 8.94 0.00 0.00 31.99 82.92
C95LH011 52.61 8.77 13.77 12.44 0.00 0.00 59.78 147.37
C95LH013 67.20 11.20 13.77 12.44 0.00 0.00 76.36 180.97
C95LH015 89.57 14.93 19.57 17.58 0.00 0.00 101.77 243.42
C95LH022 19.03 3.21 2.16 3.17 0.78 0.12 21.68 50.15
C95LH023 26.56 4.48 4.01 5.17 1.04 0.16 30.25 71.67
D10
D10IR003 10.17 1.48 0.00 0.79 0.00 0.00 14.64 27.08
D10IR005 38.37 4.07 28.51 3.45 0.00 0.00 55.26 129.66
D10SU002 12.53 1.82 0.00 0.80 0.00 0.00 18.04 33.19
D10SU003 12.81 1.86 0.00 0.80 0.00 0.00 18.45 33.92
D10SU005 19.47 2.07 34.48 4.18 0.00 0.00 28.04 88.24
D10SU006 19.71 2.09 34.48 4.18 0.00 0.00 28.38 88.84
D15
D15BI001 1.23 0.13 3.25 0.45 0.00 0.00 1.59 6.65
D15BI002 2.24 0.24 2.65 0.32 0.00 0.00 2.91 8.36
D15BI003 3.46 0.37 3.98 0.48 0.00 0.00 4.48 12.77
D15BI004 5.29 0.56 5.97 0.72 0.00 0.00 6.86 19.40
D15BI005 7.10 0.75 8.22 1.00 0.00 0.00 9.21 26.28
D15BI006 11.32 1.20 15.78 1.91 0.00 0.00 14.67 44.88
D15BI007 13.97 1.48 25.07 3.04 0.00 0.00 18.10 61.66
D15BI008 15.61 1.66 25.07 3.04 0.00 0.00 20.23 65.61
D15VE001 3.77 0.40 3.45 0.42 0.00 0.00 4.88 12.92
2-267
2 215
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

D15 cont.
D15VE002 6.44 0.68 6.23 0.75 0.00 0.00 8.34 22.44
D15VE003 9.01 0.96 8.36 1.01 0.00 0.00 11.68 31.02
D15VE004 11.19 1.19 11.01 1.33 0.00 0.00 14.50 39.22
D15VE005 31.98 3.39 16.58 2.01 0.00 0.00 41.45 95.41
D15VE006 23.46 2.49 18.57 2.25 0.00 0.00 30.41 77.18
D15VE007 40.14 4.26 26.52 3.21 0.00 0.00 52.02 126.15
D15VE008 44.79 4.75 29.84 3.62 0.00 0.00 58.05 141.05
D15VE009 0.53 0.06 1.49 0.21 0.00 0.00 0.69 2.98
D15VE010 1.55 0.17 2.92 0.35 0.00 0.00 2.01 7.00
D15VE011 1.58 0.17 2.92 0.35 0.00 0.00 2.05 7.07
D15VE012 3.24 0.34 3.65 0.44 0.00 0.00 4.19 11.86
D15XX001 0.72 0.08 0.00 0.00 0.00 0.00 0.94 1.74
D15XX002 1.09 0.12 0.00 0.00 0.00 0.00 1.42 2.63
D20
D20AD007 1.60 0.14 0.61 1.10 0.00 0.00 1.96 5.41
D20DN001 0.22 0.02 0.27 0.13 0.00 0.00 0.26 0.90
D20DN002 0.31 0.03 0.17 0.08 0.00 0.00 0.38 0.97
D20DN003 0.95 0.08 4.87 0.34 0.00 0.00 1.16 7.40
D20DN004 0.97 0.08 0.95 0.46 0.00 0.00 1.19 3.65
D20HG022 1.33 0.11 4.87 0.34 0.00 0.00 1.62 8.27
D25
D25AD003 10.03 1.06 9.15 0.95 0.00 0.00 14.45 35.64
D25AD004 6.46 0.69 3.71 0.38 0.00 0.00 9.30 20.54
D25EZ001 0.67 0.07 0.00 0.50 0.00 0.00 0.97 2.21
D25EZ002 0.51 0.06 0.00 0.50 0.13 0.02 0.76 1.98
D25EZ003 0.59 0.07 0.00 0.50 0.09 0.01 0.86 2.12
2-268
2 216
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

D25 cont.
D25EZ005 2.23 0.25 0.00 1.25 0.18 0.03 3.24 7.18
D30
D30HD001 12.81 1.36 27.85 5.37 0.00 0.00 18.44 65.83
D30HD002 16.21 1.72 35.81 7.34 0.00 0.00 23.34 84.42
D30HD003 19.75 2.10 44.43 9.38 0.00 0.00 28.45 104.11
D30MR001 1.10 0.12 2.17 0.30 0.00 0.00 1.59 5.28
D30MR003 7.36 0.79 7.69 0.93 0.17 0.03 10.64 27.61
D30MR005 17.66 1.91 17.92 2.17 0.61 0.09 25.54 65.90
D30MR006 18.20 1.96 20.52 2.49 0.61 0.09 26.31 70.18
D30MR007 23.04 2.48 20.52 2.49 0.61 0.09 33.30 82.53
D35
D35DT001 46.38 6.10 59.68 9.81 0.00 0.00 62.61 184.58
D35DT002 47.63 6.26 59.68 9.81 0.00 0.00 64.31 187.69
D35DT003 53.87 7.09 59.68 9.81 0.00 0.00 72.73 203.18
D35DT004 57.13 7.51 69.63 11.45 0.00 0.00 77.12 222.84
D35DT005 88.91 11.69 100.79 16.57 0.00 0.00 120.03 337.99
D35DT006 60.35 10.06 100.79 13.94 0.00 0.00 81.48 266.62
D35IB003 34.30 5.77 70.69 9.78 1.04 0.16 46.39 168.13
D35IB004 32.57 5.50 69.37 9.60 1.42 0.22 44.08 162.76
D35IB005 37.83 6.37 83.96 11.62 1.42 0.22 51.17 192.59
D35IB006 39.79 6.70 85.75 11.86 1.42 0.22 53.83 199.57
D35RL007 41.37 5.51 80.42 13.22 1.52 0.23 56.00 198.27
F10
F10JC001 5.84 0.59 8.11 0.84 1.12 0.17 6.11 22.78
F10JC002 6.38 0.65 8.11 0.84 1.12 0.17 6.67 23.94
2-269
2 217
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

G10
G10CA012 3.58 0.29 33.97 3.52 0.00 0.00 2.97 44.33 4.48 0.30 44.93 4.66 0.00 0.00 4.25 58.62
G10CA013 4.69 0.38 43.82 4.54 0.00 0.00 3.89 57.32 5.86 0.39 57.95 6.01 0.00 0.00 5.56 75.77
G10CA014 6.41 0.51 57.99 6.01 0.00 0.00 5.32 76.24 8.01 0.53 76.70 7.95 0.00 0.00 7.60 100.79
G10CA015 8.52 0.68 74.33 7.70 0.00 0.00 7.07 98.30 10.65 0.70 98.30 10.19 0.00 0.00 10.10 129.94
G10CA016 10.42 0.84 88.39 9.16 0.00 0.00 8.65 117.46 13.03 0.86 116.90 12.11 0.00 0.00 12.36 155.26
G10CA017 23.51 1.88 108.19 11.21 0.00 0.00 19.52 164.31 29.39 1.94 143.09 14.83 0.00 0.00 27.89 217.14
G10CA018 27.62 2.21 238.67 24.73 0.00 0.00 22.93 316.16 34.53 2.27 315.66 32.71 0.00 0.00 32.76 417.93
G10CA019 39.94 3.20 249.27 25.83 0.00 0.00 33.15 351.39 49.92 3.29 329.68 34.17 0.00 0.00 47.37 464.43
G10CA020 2.90 0.23 18.83 1.95 0.00 0.00 2.40 26.31 3.62 0.24 24.90 2.58 0.00 0.00 3.44 34.78
G10WC001 0.17 0.01 1.77 0.18 0.00 0.00 0.12 2.25 0.19 0.01 2.32 0.24 0.00 0.00 0.16 2.92
G10WC002 0.20 0.01 2.44 0.25 0.00 0.00 0.14 3.04 0.23 0.01 3.18 0.33 0.00 0.00 0.19 3.94
G10WC003 0.63 0.04 3.55 0.37 0.00 0.00 0.45 5.04 0.72 0.04 4.63 0.48 0.00 0.00 0.60 6.47
G10WC004 0.34 0.02 3.99 0.41 0.00 0.00 0.24 5.00 0.39 0.02 5.21 0.54 0.00 0.00 0.33 6.49
G10XX001 0.10 0.01 0.55 0.06 0.00 0.00 0.07 0.79 0.12 0.01 0.72 0.07 0.00 0.00 0.10 1.02
G10XX002 0.40 0.03 3.99 0.41 0.00 0.00 0.28 5.11 0.45 0.03 5.21 0.54 0.00 0.00 0.38 6.61
G10XX003 1.47 0.10 2.49 0.26 0.00 0.00 1.05 5.37 1.69 0.10 3.29 0.34 0.00 0.00 1.40 6.82
G10XX004 0.76 0.05 0.97 0.10 0.00 0.00 0.54 2.42 0.87 0.05 1.29 0.13 0.00 0.00 0.72 3.06
G10XX005 2.48 0.20 7.99 0.83 0.00 0.00 2.06 13.56 3.10 0.20 10.42 1.08 0.00 0.00 2.94 17.74
G10XX006 1.64 0.13 11.09 1.15 0.00 0.00 1.36 15.37 2.04 0.13 14.48 1.50 0.00 0.00 1.94 20.09
G10XX007 1.20 0.10 15.53 1.61 0.00 0.00 1.00 19.44 1.50 0.10 20.27 2.10 0.00 0.00 1.43 25.40
G10XX008 2.34 0.19 11.58 1.20 0.00 0.00 1.94 17.25 2.92 0.19 15.31 1.59 0.00 0.00 2.78 22.79
G10XX009 2.20 0.18 15.47 1.60 0.00 0.00 1.83 21.28 2.75 0.18 20.46 2.12 0.00 0.00 2.61 28.12
G10XX010 5.71 0.46 18.39 1.91 0.00 0.00 4.74 31.21 7.14 0.47 24.33 2.52 0.00 0.00 6.77 41.23
G10XX011 4.82 0.39 40.57 4.20 0.00 0.00 4.00 53.98 6.03 0.40 53.66 5.56 0.00 0.00 5.72 71.37
G10XX012 7.58 0.61 46.31 4.80 0.00 0.00 6.29 65.59 9.47 0.62 61.24 6.35 0.00 0.00 8.99 86.67
G10XX013 6.35 0.51 61.67 6.39 0.00 0.00 5.27 80.19 7.94 0.52 81.56 8.45 0.00 0.00 7.53 106.00
G10XX014 7.16 0.57 77.14 7.99 0.00 0.00 5.94 98.80 8.95 0.59 102.02 10.57 0.00 0.00 8.49 130.62
2-270
2 218
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

G10 cont.
G10XX015 14.86 1.19 113.60 11.77 0.00 0.00 12.33 153.75 18.57 1.22 150.24 15.57 0.00 0.00 17.62 203.22
G10XX016 13.92 1.12 154.17 15.98 0.00 0.00 11.56 196.75 17.40 1.15 203.90 21.13 0.00 0.00 16.51 260.09
G15
G15CA001 15.72 2.41 13.97 2.05 2.20 0.34 18.35 55.04 16.88 2.42 17.82 2.62 7.26 1.11 22.34 70.45
G15CA003 15.59 2.40 15.99 2.35 2.20 0.34 18.21 57.08 16.75 2.40 20.40 3.00 7.26 1.11 22.16 73.08
G15CA004 16.01 2.47 18.52 2.72 2.70 0.41 18.71 61.54 17.19 2.48 23.63 3.47 8.91 1.36 22.78 79.82
G15CA005 23.99 3.73 26.21 3.85 5.45 0.83 28.11 92.17 25.77 3.75 33.44 4.91 18.00 2.75 34.22 122.84
G15CA006 36.76 5.67 30.06 4.42 6.82 1.04 42.96 127.73 39.48 5.68 38.35 5.63 22.52 3.45 52.29 167.40
G15CA009 17.75 2.73 21.56 3.17 2.70 0.41 20.74 69.06 19.07 2.74 27.50 4.04 8.91 1.36 25.24 88.86
G15JD008 11.95 1.90 15.28 2.24 4.32 0.66 14.07 50.42 12.83 1.90 19.50 2.86 14.25 2.18 17.12 70.64
G15JD009 12.69 2.01 15.79 2.32 4.88 0.75 14.93 53.37 13.63 2.01 20.14 2.96 16.48 2.52 18.17 75.91
G15JD010 12.96 2.05 18.72 2.75 4.32 0.66 15.24 56.70 13.92 2.06 23.89 3.51 14.25 2.18 18.55 78.36
G15JD011 15.06 2.37 20.75 3.05 4.88 0.75 17.69 64.55 16.18 2.37 26.47 3.89 16.48 2.52 21.53 89.44
H10
H10NP019 0.87 0.05 0.00 0.80 0.00 0.00 1.20 2.92
H10NP020 0.91 0.06 0.00 0.80 0.00 0.00 1.25 3.02
H10NP021 1.06 0.07 0.00 1.20 0.00 0.00 1.47 3.80
H10NP022 1.32 0.08 0.00 1.20 0.00 0.00 1.82 4.42
H10NP023 1.72 0.11 0.00 1.60 0.00 0.00 2.38 5.81
H10NP024 2.74 0.17 0.00 1.60 0.00 0.00 3.78 8.29
H10NP025 4.89 0.30 0.00 2.00 0.00 0.00 6.75 13.94
H10NP026 6.24 0.38 0.00 2.00 0.00 0.00 8.61 17.23
H10NP027 7.33 0.45 0.00 2.00 0.00 0.00 10.12 19.90
H10NP028 10.22 0.63 0.00 2.40 0.00 0.00 14.10 27.35
H10NP029 13.36 0.82 0.00 2.40 0.00 0.00 18.44 35.02
H10NP030 32.72 2.01 0.00 2.40 0.00 0.00 45.16 82.29
2-271
2 219
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

H13
H13AY007 15.66 1.51 0.00 0.00 0.00 0.00 19.44 36.61
H13AY008 7.63 0.74 0.00 0.00 0.00 0.00 9.47 17.84
H13AY009 13.92 1.34 0.00 0.00 0.00 0.00 17.28 32.54
H13AY010 7.04 0.68 0.00 0.00 0.00 0.00 8.74 16.46
H13AY011 11.63 1.12 0.00 0.00 0.00 0.00 14.43 27.18
H13AY012 5.89 0.57 0.00 0.00 0.00 0.00 7.31 13.77
H13AY013 9.32 0.90 0.00 0.00 0.00 0.00 11.57 21.79
H13AY014 4.96 0.48 0.00 0.00 0.00 0.00 6.15 11.59
H13AY015 5.48 0.53 0.00 0.00 0.00 0.00 6.81 12.82
H13AY016 3.53 0.34 0.00 0.00 0.00 0.00 4.38 8.25
H13AY017 17.39 1.68 0.00 0.00 0.00 0.00 21.59 40.66
H13AY018 8.79 0.85 0.00 0.00 0.00 0.00 10.91 20.55
H13AY019 1.14 0.11 0.06 0.28 0.00 0.00 1.42 3.01
H13AY020 1.49 0.14 0.06 0.28 0.00 0.00 1.84 3.81
H13AY021 19.65 1.75 0.00 0.00 0.64 0.10 20.45 42.59
H13AY022 10.50 0.95 0.00 0.00 0.64 0.10 10.95 23.14
H13AY023 17.82 1.59 0.00 0.00 0.64 0.10 18.55 38.70
H13AY024 9.28 0.84 0.00 0.00 0.64 0.10 9.69 20.55
H13AY025 15.86 1.42 0.00 0.00 0.64 0.10 16.51 34.53
H13AY026 8.54 0.77 0.00 0.00 0.64 0.10 8.91 18.96
H13AY027 13.30 1.19 0.00 0.00 0.64 0.10 13.86 29.09
H13AY028 7.20 0.66 0.00 0.00 0.64 0.10 7.52 16.12
H13AY029 10.72 0.97 0.00 0.00 0.64 0.10 11.18 23.61
H13AY030 6.09 0.56 0.00 0.00 0.64 0.10 6.37 13.76
H13AY031 7.00 0.64 0.00 0.00 0.64 0.10 7.31 15.69
H13AY032 4.56 0.42 0.00 0.00 0.64 0.10 4.78 10.50
H13BB001 3.36 0.14 0.62 1.05 0.00 0.00 4.36 9.53
2-272
2 220
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

H13 cont.
H13BB002 4.29 0.17 0.93 1.45 0.00 0.00 5.57 12.41
H13BC003 4.98 0.22 0.31 0.17 0.00 0.00 4.81 10.49
H13BC006 3.60 0.16 0.19 0.10 0.00 0.00 3.48 7.53
H13BC007 5.94 0.26 0.19 0.10 0.00 0.00 5.74 12.23
H13BC008 6.84 0.30 0.31 0.17 0.00 0.00 6.61 14.23
H13BC009 5.14 0.22 0.19 0.10 0.00 0.00 4.97 10.62
H13BC010 2.92 0.13 0.19 0.10 0.00 0.00 2.82 6.16
H13BC011 4.53 0.20 0.31 0.17 0.00 0.00 4.38 9.59
H13BC012 3.71 0.16 0.19 0.10 0.00 0.00 3.58 7.74
H13BC013 3.35 0.15 0.19 0.10 0.00 0.00 3.24 7.03
H13CB001 2.23 0.20 0.31 0.42 0.00 0.00 2.32 5.48
H13CB002 2.42 0.21 0.62 0.59 0.00 0.00 2.51 6.35
H13CO002 0.94 0.08 0.31 0.42 0.00 0.00 0.98 2.73
H13CO003 1.63 0.19 0.19 0.35 0.00 0.00 2.02 4.38
H13CO004 2.45 0.28 0.19 0.60 0.00 0.00 3.05 6.57
H13CO005 4.38 0.50 0.19 0.60 0.00 0.00 5.43 11.10
H13CO006 3.64 0.41 0.19 0.45 0.00 0.00 4.52 9.21
H13EP001 2.63 0.23 0.31 0.42 0.00 0.00 2.74 6.33
H13EP002 2.67 0.30 0.46 0.55 0.00 0.00 3.32 7.30
H13KP001 7.62 0.68 0.77 0.42 0.15 0.02 7.93 17.59
H13KP002 8.65 0.77 0.96 0.52 0.15 0.02 9.00 20.07
H13KP003 10.19 0.90 1.36 0.74 0.15 0.02 10.59 23.95
H13KP004 11.72 1.04 1.73 0.94 0.15 0.02 12.19 27.79
H13MN001 32.31 2.88 9.26 7.51 0.66 0.10 37.83 90.55
H13MN002 37.67 3.37 12.35 10.01 0.95 0.15 44.12 108.62
H13MN003 42.79 3.82 12.35 11.01 0.95 0.15 50.11 121.18
H13MN004 48.93 4.36 18.53 15.02 0.95 0.15 57.27 145.21
2-273
2 221
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

H13 cont.
H13PR001 8.74 0.84 0.19 0.10 0.00 0.00 10.85 20.72
H13PR002 26.00 2.31 0.19 1.60 0.64 0.10 27.05 57.89
H13PR003 15.43 1.49 0.31 0.17 0.00 0.00 19.15 36.55
H13PR005 20.50 1.98 0.31 0.17 0.00 0.00 25.45 48.41
H13PR006 22.92 2.04 0.31 1.67 0.64 0.10 23.86 51.54
H13PR007 25.25 2.44 0.62 0.34 0.00 0.00 31.34 59.99
H13PR011 35.99 3.19 0.12 1.56 0.64 0.10 37.43 79.03
H13PR012 38.72 3.43 0.19 1.60 0.64 0.10 40.27 84.95
H13PR013 41.11 3.64 0.31 1.67 0.64 0.10 42.75 90.22
H13PR014 46.27 4.09 0.49 1.76 0.64 0.10 48.11 101.46
H13PR015 52.75 4.66 0.49 1.76 0.64 0.10 54.84 115.24
H13PR022 18.12 1.75 0.12 0.06 0.00 0.00 22.50 42.55
H13PR023 20.72 2.00 0.19 0.10 0.00 0.00 25.72 48.73
H13PR024 22.98 2.22 0.19 0.10 0.00 0.00 28.52 54.01
H13PR025 27.84 2.68 0.19 0.10 0.00 0.00 34.55 65.36
H13PR026 33.94 3.27 0.25 0.14 0.00 0.00 42.13 79.73
H13S5001 5.24 0.46 0.19 0.10 0.00 0.00 5.44 11.43
H13S5002 8.20 0.72 0.31 0.17 0.00 0.00 8.52 17.92
H13S5003 9.74 0.86 0.31 0.17 0.00 0.00 10.12 21.20
H13SH001 5.07 0.45 1.24 0.60 0.00 0.00 5.92 13.28
H13SH002 4.75 0.42 1.24 0.60 0.00 0.00 5.55 12.56
H13SH003 8.18 0.72 2.47 1.20 0.00 0.00 9.55 22.12
H13SH004 8.53 0.75 2.47 1.20 0.00 0.00 9.97 22.92
H13SH005 13.58 1.19 6.18 3.01 0.00 0.00 15.87 39.83
H13SH006 43.90 3.86 18.53 9.02 0.00 0.00 51.28 126.59
H13SH007 57.21 5.03 37.05 18.03 0.00 0.00 66.84 184.16
H13TH001 1.24 0.11 0.31 0.17 0.00 0.00 1.28 3.11
2-274
2 222
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

H13 cont.
H13TH002 2.28 0.20 0.97 0.10 0.08 0.01 2.37 6.01
H13TH003 2.57 0.23 0.97 0.10 0.08 0.01 2.68 6.64
H13YB001 34.36 3.02 3.09 1.67 0.00 0.00 35.70 77.84
H13YB002 34.36 3.02 3.09 1.67 0.00 0.00 35.70 77.84
H13YB003 34.36 3.02 3.09 1.67 0.00 0.00 35.70 77.84
H20
H20BE002 3.09 0.27 0.00 0.20 0.00 0.00 3.41 6.97
H20BE003 3.99 0.35 0.00 0.30 0.00 0.00 4.40 9.04
H20BE004 5.80 0.51 0.00 0.40 0.00 0.00 6.40 13.11
H25
H25AU006 0.85 0.05 0.00 0.00 0.00 0.00 1.11 2.01
H25AU007 1.00 0.06 0.00 0.00 0.00 0.00 1.30 2.36
H25AU008 1.65 0.09 0.00 0.00 0.00 0.00 2.14 3.88
H25AU009 2.36 0.13 0.00 0.00 0.00 0.00 3.07 5.56
H25AU010 2.60 0.15 0.00 0.00 0.00 0.00 3.38 6.13
H25AX001 1.16 0.07 0.00 0.00 0.00 0.00 1.51 2.74
H25AX002 1.32 0.07 0.00 0.00 0.00 0.00 1.71 3.10
H25AX003 1.44 0.08 0.00 0.00 0.00 0.00 1.88 3.40
H25AX004 1.69 0.09 0.00 0.00 0.00 0.00 2.19 3.97
H25AX005 1.71 0.10 0.00 0.00 0.00 0.00 2.22 4.03
H25AX006 2.15 0.12 0.00 0.00 0.00 0.00 2.79 5.06
H25BS001 0.95 0.06 0.00 0.00 0.00 0.00 1.05 2.06
H25BS002 0.96 0.06 0.00 0.00 0.00 0.00 1.06 2.08
H25BS003 1.25 0.08 0.00 0.00 0.00 0.00 1.38 2.71
H25BS004 1.67 0.10 0.00 0.00 0.00 0.00 1.85 3.62
H25BS005 2.24 0.14 0.00 0.00 0.00 0.00 2.48 4.86
2-275
2 223
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

H25 cont.
H25CA020 11.93 1.09 8.55 1.30 0.00 0.00 11.90 34.77 14.49 1.11 11.30 1.72 0.00 0.00 17.56 46.18
H25CA021 11.98 1.10 9.09 1.38 0.00 0.00 11.95 35.50 14.55 1.12 12.02 1.83 0.00 0.00 17.64 47.16
H25CA022 13.73 1.73 13.85 2.10 0.00 0.00 15.66 47.07 16.48 1.75 18.32 2.78 0.00 0.00 22.33 61.66
H25CA023 19.99 2.51 13.85 2.10 0.00 0.00 22.79 61.24 23.99 2.55 18.32 2.78 0.00 0.00 32.49 80.13
H25CA034 3.68 0.32 1.95 0.30 0.00 0.00 3.67 9.92 4.21 0.32 2.58 0.39 0.00 0.00 4.80 12.30
H25CA035 4.28 0.37 3.25 0.49 0.00 0.00 4.27 12.66 4.89 0.38 4.29 0.65 0.00 0.00 5.58 15.79
H25CA036 6.89 0.60 5.08 0.77 0.00 0.00 6.87 20.21 7.87 0.61 6.73 1.02 0.00 0.00 8.97 25.20
H25CA038 9.34 0.85 5.84 0.89 0.00 0.00 9.31 26.23 11.34 0.87 7.73 1.17 0.00 0.00 13.74 34.85
H25CA040 9.15 1.15 13.52 2.05 0.00 0.00 10.43 36.30 10.98 1.17 17.89 2.72 0.00 0.00 14.87 47.63
H25CA055 3.04 0.17 0.00 0.40 0.00 0.00 3.56 7.17
H25CA057 12.17 0.68 0.00 0.80 0.00 0.00 14.22 27.87
H25CA065 44.58 8.66 56.58 2.94 0.00 0.00 69.90 182.66 56.47 8.75 74.84 3.89 0.00 0.00 100.59 244.54
H25CA066 15.46 0.87 0.00 0.00 0.00 0.00 18.06 34.39
H25CA067 18.14 1.02 0.00 0.00 0.00 0.00 21.19 40.35
H25CA068 7.15 0.40 0.00 0.00 0.00 0.00 9.28 16.83
H25CA069 8.62 0.48 0.00 0.00 0.00 0.00 11.20 20.30
H25CA070 12.09 0.68 0.00 0.00 0.00 0.00 15.70 28.47
H25KC017 8.74 0.80 5.84 0.89 0.00 0.00 8.72 24.99 10.61 0.82 7.73 1.17 0.00 0.00 12.86 33.19
H25KC019 12.55 1.58 15.47 2.35 0.00 0.00 14.30 46.25 15.05 1.60 20.46 3.11 0.00 0.00 20.39 60.61
H25KC020 16.53 2.08 15.47 2.35 0.00 0.00 18.85 55.28 19.84 2.11 20.46 3.11 0.00 0.00 26.87 72.39
H25KC027 14.26 1.31 10.04 1.53 0.00 0.00 14.22 41.36 17.32 1.33 13.28 2.02 0.00 0.00 20.99 54.94
H25KC028 15.32 1.92 19.04 2.89 0.00 0.00 17.46 56.63 18.38 1.95 25.18 3.83 0.00 0.00 24.90 74.24
H25KC029 20.50 2.58 19.04 2.89 0.00 0.00 23.36 68.37 24.59 2.61 25.18 3.83 0.00 0.00 33.32 89.53
H25KC030 20.78 2.61 25.75 3.91 0.00 0.00 23.69 76.74 24.94 2.65 34.06 5.18 0.00 0.00 33.78 100.61
H25KC031 21.67 3.57 37.33 1.79 0.00 0.00 30.88 95.24 25.68 3.60 49.37 2.37 0.00 0.00 40.27 121.29
H25KM001 12.80 1.17 9.63 1.46 0.00 0.00 12.76 37.82 15.54 1.20 12.74 1.94 0.00 0.00 18.84 50.26
H25KM003 17.62 1.61 11.90 1.81 0.00 0.00 17.57 50.51 21.39 1.65 15.74 2.39 0.00 0.00 25.93 67.10
2-276
2 224
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

H25 cont.
H25KM009 39.35 7.64 49.12 2.56 0.00 0.00 61.70 160.37 49.84 7.73 64.96 3.38 0.00 0.00 88.79 214.70
H25KM015 31.89 5.26 41.54 1.99 0.00 0.00 45.45 126.13 37.79 5.30 54.95 2.63 0.00 0.00 59.26 159.93
H25KM018 4.69 0.41 2.16 0.33 0.00 0.00 4.68 12.27 5.36 0.41 2.86 0.43 0.00 0.00 6.11 15.17
H25KM021 6.28 0.54 4.22 0.64 0.00 0.00 6.27 17.95 7.18 0.55 5.58 0.85 0.00 0.00 8.19 22.35
H25KM022 8.04 0.70 4.33 0.66 0.00 0.00 8.02 21.75 9.19 0.71 5.72 0.87 0.00 0.00 10.48 26.97
H25KM023 9.91 0.86 5.84 0.89 0.00 0.00 9.88 27.38 11.32 0.87 7.73 1.17 0.00 0.00 12.91 34.00
H25KM027 18.14 1.66 9.30 1.41 0.00 0.00 18.09 48.60 22.03 1.69 12.31 1.87 0.00 0.00 26.70 64.60
H25KM033 91.82 17.84 98.24 5.11 0.00 0.00 143.97 356.98 116.31 18.03 129.93 6.76 0.00 0.00 207.18 478.21
H25KN001 4.47 0.25 0.00 0.50 0.00 0.00 5.80 11.02
H25KN002 6.19 0.35 0.00 0.50 0.00 0.00 8.04 15.08
H25KN003 7.55 0.42 0.00 0.50 0.00 0.00 9.80 18.27
H25KN004 8.68 0.49 0.00 0.50 0.00 0.00 11.27 20.94
H25KN006 17.50 0.98 0.00 1.00 0.00 0.00 22.73 42.21
H25KN007 0.90 0.05 0.00 0.15 0.00 0.00 1.17 2.27
H25KN009 1.86 0.10 0.00 0.15 0.00 0.00 2.42 4.53
H25KN010 2.56 0.14 0.00 0.15 0.00 0.00 3.33 6.18
H25LB003 14.44 1.32 10.28 1.56 0.00 0.00 14.41 42.01 17.54 1.35 13.59 2.07 0.00 0.00 21.26 55.81
H25LB005 16.91 1.55 12.98 1.97 0.00 0.00 16.87 50.28 20.54 1.58 17.17 2.61 0.00 0.00 24.89 66.79
H25LU001 4.03 0.23 0.00 0.40 0.00 0.00 4.71 9.37
H25LU002 4.55 0.26 0.00 0.50 0.00 0.00 5.32 10.63
H25LU003 7.07 0.40 0.00 0.80 0.00 0.00 8.26 16.53
H25LU004 8.22 0.46 0.00 0.90 0.00 0.00 9.60 19.18
H25LU005 10.30 0.58 0.00 1.10 0.00 0.00 12.03 24.01
H25LU006 14.43 0.81 0.00 1.50 0.00 0.00 16.86 33.60
H25LU007 12.29 0.69 0.00 1.40 0.00 0.00 14.36 28.74
H25LU008 16.08 0.90 0.00 1.60 0.00 0.00 18.79 37.37
H25LU009 17.64 0.99 0.00 1.70 0.00 0.00 20.61 40.94
2-277
2 225
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

H25 cont.
H25LU010 21.18 1.19 0.00 2.00 0.00 0.00 24.74 49.11
H25LU011 20.99 1.18 0.00 2.00 0.00 0.00 24.52 48.69
H25LU012 25.69 1.44 0.00 2.50 0.00 0.00 30.02 59.65
H25LU013 26.57 1.49 0.00 2.60 0.00 0.00 31.04 61.70
H25LU014 30.92 1.73 0.00 3.00 0.00 0.00 36.12 71.77
H25LU023 5.13 0.31 0.00 0.25 0.00 0.00 5.66 11.35
H25LU024 2.61 0.16 0.00 0.30 0.00 0.00 2.88 5.95
H25LU025 3.20 0.20 0.00 0.40 0.00 0.00 3.53 7.33
H25LU026 3.63 0.22 0.00 0.50 0.00 0.00 4.01 8.36
H25LU027 4.06 0.25 0.00 0.60 0.00 0.00 4.48 9.39
H25LU028 6.53 0.40 0.00 0.70 0.00 0.00 7.21 14.84
H25LU034 9.61 0.59 0.00 0.80 0.00 0.00 10.61 21.61
H25LU035 11.48 0.70 0.00 0.90 0.00 0.00 12.67 25.75
H25LU036 13.19 0.81 0.00 1.00 0.00 0.00 14.56 29.56
H25LU040 21.34 1.20 0.00 0.75 0.00 0.00 27.71 51.00
H25LU041 26.16 1.47 0.00 0.75 0.00 0.00 33.98 62.36
H25LU042 31.54 1.77 0.00 1.50 0.00 0.00 40.97 75.78
H25LU046 4.93 0.28 0.00 0.50 0.00 0.00 6.40 12.11
H25LU047 5.83 0.33 0.00 0.60 0.00 0.00 7.58 14.34
H25LU048 6.24 0.35 0.00 0.70 0.00 0.00 8.11 15.40
H25LU049 7.53 0.42 0.00 0.80 0.00 0.00 9.78 18.53
H25LU050 11.39 0.64 0.00 0.90 0.00 0.00 14.80 27.73
H25LU053 22.46 1.26 0.00 0.75 0.00 0.00 29.17 53.64
H25LU054 27.65 1.55 0.00 0.75 0.00 0.00 35.91 65.86
H25ME001 2.87 0.25 1.44 0.22 0.00 0.00 2.86 7.64 3.27 0.25 1.90 0.29 0.00 0.00 3.73 9.44
H25ME002 4.10 0.35 4.33 0.66 0.00 0.00 4.08 13.52 4.68 0.36 5.72 0.87 0.00 0.00 5.34 16.97
H25ME003 5.68 0.49 5.19 0.79 0.00 0.00 5.67 17.82 6.50 0.50 6.87 1.04 0.00 0.00 7.41 22.32
2-278
2 226
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

H25 cont.
H25WN001 1.07 0.07 0.00 0.00 0.00 0.00 1.18 2.32
H25WN002 1.20 0.07 0.00 0.00 0.00 0.00 1.56 2.83
H25WN003 1.32 0.07 0.00 0.00 0.00 0.00 1.71 3.10
H25WN004 1.44 0.08 0.00 0.00 0.00 0.00 1.87 3.39
H25WN005 1.63 0.09 0.00 0.00 0.00 0.00 2.12 3.84
H30
H30CA005 18.62 1.69 15.28 2.20 2.19 0.34 13.41 53.73 22.91 1.73 19.50 2.80 7.88 1.21 18.17 74.20
H30CA007 15.49 1.43 12.25 1.76 2.49 0.38 11.20 45.00 19.07 1.46 15.62 2.25 8.98 1.37 15.19 63.94
H30GA006 27.64 2.47 23.58 3.39 1.88 0.29 19.83 79.08 34.02 2.52 30.09 4.33 6.65 1.02 26.87 105.50
H30GA007 20.78 1.85 13.97 2.01 1.15 0.18 14.89 54.83 25.58 1.89 17.82 2.56 4.06 0.62 20.18 72.71
H30GA008 24.23 2.72 21.16 3.04 7.34 1.12 21.01 80.62 30.28 2.78 26.64 3.83 25.99 3.98 28.48 121.98
H30KM001 18.68 2.03 12.45 1.79 1.47 0.22 16.06 52.70 23.35 2.07 15.88 2.28 5.28 0.81 21.77 71.44
H35
H35CA001 56.36 8.40 71.95 3.74 0.00 0.00 90.38 230.83 64.41 8.47 95.15 4.95 0.00 0.00 111.91 284.89
H35CA003 111.80 16.67 119.44 6.21 0.00 0.00 179.29 433.41 127.77 16.80 157.97 8.22 0.00 0.00 222.00 532.76
H35CA004 185.93 27.73 165.53 8.61 0.00 0.00 298.18 685.98 212.49 27.95 218.93 11.39 0.00 0.00 369.20 839.96
H35CA005 365.37 54.49 272.64 14.18 0.00 0.00 585.95 1,292.63 417.56 54.92 360.59 18.76 0.00 0.00 725.51 1,577.34
H35HI006 83.64 12.47 69.35 3.61 0.00 0.00 134.14 303.21 95.59 12.57 91.72 4.77 0.00 0.00 166.08 370.73
L10
L10BS002 3.29 0.32 0.00 0.30 0.00 0.00 4.15 8.06 4.70 0.33 0.00 0.30 0.00 0.00 6.59 11.92
L10BS004 2.25 0.22 0.00 0.25 0.00 0.00 2.84 5.56 3.22 0.23 0.00 0.25 0.00 0.00 4.51 8.21
L10BS005 3.29 0.32 0.00 0.30 0.00 0.00 4.16 8.07 4.71 0.33 0.00 0.30 0.00 0.00 6.60 11.94
L10BS007 2.35 0.23 0.00 0.50 0.00 0.00 2.97 6.05 3.36 0.24 0.00 0.50 0.00 0.00 4.72 8.82
L10BU005 0.81 0.08 0.00 1.10 0.00 0.00 1.02 3.01 1.15 0.08 0.00 1.10 0.00 0.00 1.62 3.95
L10BU010 0.33 0.03 0.00 0.80 0.00 0.00 0.41 1.57 0.47 0.03 0.00 0.80 0.00 0.00 0.66 1.96
2-279
2 227
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

L10 cont.
L10BU011 0.67 0.06 0.00 1.50 0.00 0.00 0.84 3.07 0.95 0.07 0.00 1.50 0.00 0.00 1.34 3.86
L10BU012 1.37 0.13 0.00 2.00 0.00 0.00 1.73 5.23 1.96 0.14 0.00 2.00 0.00 0.00 2.75 6.85
L10BU013 1.66 0.16 0.00 2.50 0.00 0.00 2.10 6.42 2.37 0.17 0.00 2.50 0.00 0.00 3.33 8.37
L10RM001 4.40 0.42 0.00 0.40 0.00 0.00 5.56 10.78 6.29 0.44 0.00 0.40 0.00 0.00 8.82 15.95
L10RM002 3.95 0.38 0.00 0.00 0.00 0.00 4.99 9.32 5.65 0.40 0.00 0.00 0.00 0.00 7.92 13.97
L10VE002 1.99 0.20 7.11 0.92 0.10 0.02 2.52 12.86 2.84 0.20 9.21 1.19 0.33 0.05 4.00 17.82
L10VE005 1.02 0.10 2.64 0.34 0.09 0.01 1.30 5.50 1.46 0.11 3.42 0.44 0.29 0.04 2.07 7.83
L10VE006 2.77 0.27 4.06 0.53 0.09 0.01 3.51 11.24 3.96 0.28 5.26 0.68 0.29 0.04 5.57 16.08
L10VE007 2.41 0.23 0.00 1.50 0.00 0.00 3.04 7.18 3.44 0.24 0.00 1.50 0.00 0.00 4.83 10.01
L10VE009 3.15 0.31 7.89 0.89 0.09 0.01 3.99 16.33 4.50 0.32 10.07 1.13 0.29 0.04 6.33 22.68
L10VE010 1.10 0.11 5.48 0.71 0.04 0.01 1.39 8.84 1.57 0.11 7.11 0.92 0.12 0.02 2.20 12.05
L15
L15BW001 4.30 0.18 6.77 0.70 0.12 0.02 3.93 16.02
L15BW002 7.87 0.33 9.48 0.98 0.24 0.04 7.19 26.13
L15BW003 9.07 0.37 13.54 1.40 0.24 0.04 8.28 32.94
L15BW004 13.57 0.55 11.94 1.24 0.00 0.00 12.34 39.64
L15FG001 14.93 0.60 21.74 2.25 0.00 0.00 13.58 53.10
L15FG002 9.91 0.40 15.25 1.58 0.15 0.02 9.03 36.34
L15HV001 0.17 0.01 1.35 0.14 0.00 0.00 0.16 1.83
L15HV002 0.26 0.01 2.71 0.28 0.00 0.00 0.24 3.50
L15HZ001 0.19 0.01 0.81 0.08 0.00 0.00 0.17 1.26
L15JD005 0.54 0.02 0.00 0.00 0.00 0.00 0.49 1.05
L15TO001 0.31 0.01 1.62 0.17 0.00 0.00 0.28 2.39
L15TO002 0.84 0.04 4.06 0.42 0.19 0.03 0.77 6.35
L15TO003 1.69 0.07 5.69 0.59 0.19 0.03 1.55 9.81
L15TO004 1.83 0.08 5.69 0.59 0.16 0.02 1.67 10.04
L15TO006 3.38 0.14 7.85 0.81 0.34 0.05 3.09 15.66
2-280
2 228
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

L15 cont.
L15TO007 3.49 0.15 7.85 0.81 0.34 0.05 3.19 15.88
L15TO009 0.28 0.01 2.17 0.22 0.00 0.00 0.25 2.93
L15TO010 0.43 0.02 2.71 0.28 0.00 0.00 0.39 3.83
L15WI001 1.81 0.08 0.00 0.05 0.11 0.02 1.66 3.73
L20
L20AB017 1.44 0.12 1.92 0.20 0.07 0.01 2.99 6.75
L20AB018 1.61 0.13 2.05 0.21 0.07 0.01 3.34 7.42
L20AB019 1.89 0.15 2.05 0.21 0.07 0.01 3.93 8.31
L20AB020 1.20 0.10 1.65 0.17 0.07 0.01 2.51 5.71
L20AB021 1.28 0.10 2.05 0.21 0.07 0.01 2.65 6.37
L20AB022 1.44 0.12 1.92 0.20 0.07 0.01 3.00 6.76
L20AB023 0.58 0.05 0.00 0.00 0.05 0.01 1.21 1.90
L20AB024 0.63 0.05 0.00 0.00 0.05 0.01 1.30 2.04
L25
L25JE002 15.28 1.22 27.19 2.82 0.46 0.07 25.35 72.39
L25JE003 0.37 0.03 1.59 0.16 0.00 0.00 0.61 2.76
L25MB002 0.51 0.05 1.45 1.15 0.37 0.06 0.90 4.49
L25MB004 16.57 1.32 55.01 7.20 0.46 0.07 27.50 108.13
L25MB005 1.07 0.10 2.90 1.30 0.37 0.06 1.82 7.62
L25MB006 10.22 0.81 17.37 3.05 0.00 0.00 16.91 48.36
L25MB007 5.73 0.45 6.66 1.69 0.00 0.00 9.49 24.02
L25MB008 17.77 1.45 27.19 4.32 1.41 0.22 29.61 81.97
L30
L30HW015 11.96 1.20 1.54 0.75 1.15 0.18 16.64 33.42 14.95 1.23 2.02 0.98 3.66 0.56 22.87 46.27
L30KB001 2.78 0.28 0.93 0.45 0.37 0.06 3.89 8.76 3.48 0.29 1.21 0.59 1.16 0.18 5.34 12.25
2-281
2 229
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

L30 cont.
L30KB002 2.94 0.30 0.93 0.45 0.37 0.06 4.10 9.15 3.67 0.31 1.21 0.59 1.16 0.18 5.64 12.76
L30RA001 6.18 0.61 2.70 0.33 0.39 0.06 8.58 18.85 7.73 0.63 3.58 0.43 1.24 0.19 11.79 25.59
L30S4001 1.99 0.19 0.93 0.45 0.00 0.00 2.75 6.31 2.49 0.20 1.21 0.59 0.00 0.00 3.78 8.27
L30S4002 1.71 0.17 0.00 0.00 0.00 0.00 2.36 4.24 2.14 0.17 0.00 0.00 0.00 0.00 3.25 5.56
L30S4005 0.14 0.01 0.00 0.00 0.00 0.00 0.19 0.34 0.18 0.01 0.00 0.00 0.00 0.00 0.27 0.46
L30S4006 0.16 0.02 0.00 0.00 0.00 0.00 0.22 0.40 0.20 0.02 0.00 0.00 0.00 0.00 0.31 0.53
L30TS001 3.02 0.32 0.74 0.36 0.82 0.13 4.26 9.65 3.77 0.33 0.97 0.47 2.60 0.40 5.85 14.39
L35
L35CA005 17.60 1.70 17.56 1.81 0.00 0.00 27.16 65.83 22.01 1.74 22.73 2.34 0.00 0.00 38.59 87.41
L35CA007 33.45 3.23 28.72 2.96 0.00 0.00 51.60 119.96 41.82 3.30 37.16 3.83 0.00 0.00 73.34 159.45
L35CA013 10.67 1.03 10.68 1.10 0.00 0.00 16.46 39.94 13.34 1.05 13.82 1.42 0.00 0.00 23.39 53.02
L35CA014 24.08 2.32 18.99 1.96 0.00 0.00 37.15 84.50 30.10 2.38 24.57 2.53 0.00 0.00 52.79 112.37
L35KM006 39.20 3.78 23.73 2.44 0.00 0.00 60.46 129.61 49.00 3.87 30.71 3.16 0.00 0.00 85.93 172.67
L40
L40CA007 27.82 3.87 37.76 3.08 17.43 2.67 27.81 120.44 31.30 3.90 49.94 4.08 62.74 9.60 33.56 195.12
L40CA009 106.46 14.63 86.55 7.06 22.96 3.51 106.15 347.32 119.77 14.75 114.47 9.34 82.66 12.65 128.08 481.72
L40CA012 14.82 1.61 15.69 1.78 1.78 0.27 18.96 54.91 16.02 1.62 20.75 2.35 6.40 0.98 21.70 69.82
L40CA013 9.15 1.01 9.74 1.10 1.78 0.27 11.75 34.80 9.89 1.02 12.88 1.46 6.40 0.98 13.45 46.08
L40CA014 20.76 2.25 21.64 2.45 1.97 0.30 26.53 75.90 22.44 2.26 28.62 3.24 7.09 1.08 30.37 95.10
L40CA015 11.67 1.19 16.12 1.83 1.78 0.27 12.32 45.18 12.34 1.20 21.32 2.41 6.40 0.98 14.90 59.55
L40CA018 75.37 10.60 67.84 5.54 21.34 3.27 75.52 259.48 84.79 10.68 89.72 7.32 76.82 11.75 91.13 372.21
L40CA019 8.38 0.87 10.28 1.16 1.78 0.27 8.87 31.61 8.86 0.87 13.59 1.54 6.40 0.98 10.73 42.97
L40CA022 11.80 1.21 13.85 1.57 1.78 0.27 12.45 42.93 12.47 1.21 18.32 2.07 6.40 0.98 15.05 56.50
L40CA023 14.28 1.47 19.47 2.20 2.76 0.42 15.10 55.70 15.10 1.48 25.76 2.92 9.93 1.52 18.27 74.98
L40CA024 17.03 1.86 21.31 2.41 8.17 1.25 18.29 70.32 18.00 1.87 28.19 3.19 29.40 4.50 22.11 107.26
L40CA025 18.19 1.97 22.83 2.58 8.17 1.25 19.50 74.49 19.23 1.98 30.19 3.42 29.40 4.50 23.58 112.30
2-282
2 230
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

L40 cont.
L40CA028 3.16 0.26 5.81 0.66 0.85 0.13 3.58 14.45
L40CA029 3.52 0.29 6.41 0.73 0.85 0.13 3.99 15.92
L40CA030 3.96 0.33 7.00 0.79 1.07 0.16 4.50 17.81
L40CA031 3.85 0.32 8.78 0.99 1.07 0.16 4.37 19.54
L40CA032 3.76 0.40 5.63 0.64 0.89 0.14 4.01 15.47 3.97 0.40 7.44 0.84 3.20 0.49 4.85 21.19
L40CA033 5.04 0.53 7.36 0.83 0.89 0.14 5.36 20.15 5.33 0.53 9.73 1.10 3.20 0.49 6.48 26.86
L40CA034 5.27 0.62 8.22 0.93 5.75 0.88 5.78 27.45 5.58 0.62 10.87 1.23 20.68 3.16 6.98 49.12
L40CA035 43.18 6.14 54.20 4.42 21.70 3.32 43.36 176.32 48.58 6.18 71.69 5.85 78.12 11.95 52.33 274.70
L40CS009 12.86 1.35 14.71 1.67 3.55 0.54 13.66 48.34 13.59 1.35 19.46 2.20 12.79 1.96 16.52 67.87
L40CS010 15.50 1.61 19.58 2.22 3.55 0.54 16.43 59.43 16.39 1.62 25.90 2.93 12.79 1.96 19.87 81.46
L40CS011 18.78 2.03 20.23 2.29 8.17 1.25 20.13 72.88 19.86 2.04 26.76 3.03 29.40 4.50 24.34 109.93
L40KM003 9.75 1.23 15.04 1.70 12.25 1.87 10.91 52.75 10.31 1.23 19.89 2.25 44.11 6.75 13.19 97.73
L40KM008 19.26 2.78 36.24 2.96 17.43 2.67 19.41 100.75 21.67 2.80 47.94 3.91 62.74 9.60 23.42 172.08
L40KM009 35.90 5.15 53.01 4.33 12.22 1.87 36.12 148.60 40.39 5.19 70.11 5.72 44.01 6.73 43.59 215.74
L40KM010 47.16 7.01 74.00 6.04 21.34 3.27 47.83 206.65 53.05 7.06 97.87 7.99 76.82 11.75 57.72 312.26
L40KM011 82.58 11.59 92.29 7.53 22.96 3.51 82.71 303.17 92.90 11.68 122.06 9.96 82.66 12.65 99.80 431.71
L40KM015 7.21 0.76 8.11 0.92 1.31 0.20 7.67 26.18 7.63 0.76 10.73 1.21 4.70 0.72 9.27 35.02
L40ME012 2.79 0.23 5.46 0.62 0.56 0.09 3.16 12.91
L40ME016 1.74 0.14 2.79 0.32 0.30 0.05 1.96 7.30
L40ME017 2.09 0.18 4.21 0.48 0.66 0.10 2.38 10.10
L40ME021 2.19 0.20 5.81 0.66 1.70 0.26 2.54 13.36
L40ME022 3.38 0.29 8.90 1.01 1.70 0.26 3.87 19.41
L40ME023 3.79 0.33 9.61 1.09 1.70 0.26 4.34 21.12
L50
L50CA001 5.41 0.60 7.29 3.28 0.73 0.11 6.55 23.97 9.01 0.63 10.32 4.64 2.60 0.40 11.60 39.20
L50CA005 10.87 1.15 8.46 3.81 0.00 0.00 13.01 37.30 18.11 1.22 11.98 5.39 0.00 0.00 23.04 59.74
L50CS005 7.23 0.80 7.54 3.39 1.00 0.15 8.76 28.87 12.05 0.85 10.68 4.80 3.55 0.54 15.51 47.98
2-283
2 231
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

L50 cont.
L50CS006 8.61 0.97 8.21 3.69 1.44 0.22 10.46 33.60 14.35 1.02 11.63 5.23 5.09 0.78 18.52 56.62
L50JC008 5.95 0.68 6.20 2.79 1.15 0.18 7.25 24.20 9.92 0.71 8.78 3.95 4.03 0.62 12.84 40.85
L50JC009 7.91 0.88 7.62 3.43 1.15 0.18 9.59 30.76 13.18 0.93 10.80 4.86 4.03 0.62 16.98 51.40
L50JC010 8.72 0.97 9.13 4.11 1.21 0.19 10.56 34.89 14.54 1.02 12.93 5.82 4.35 0.67 18.70 58.03
L50JC011 9.68 1.07 9.13 4.11 1.21 0.19 11.71 37.10 16.14 1.13 12.93 5.82 4.35 0.67 20.73 61.77
L50JC012 12.09 1.32 9.13 4.11 1.21 0.19 14.59 42.64 20.16 1.40 12.93 5.82 4.35 0.67 25.84 71.17
L55
L55KN001 1.01 0.06 0.00 0.52 0.00 0.00 1.39 2.98
L55KN002 2.06 0.13 0.00 1.06 0.00 0.00 2.85 6.10
L55KN004 1.91 0.12 0.00 0.00 0.00 0.00 2.64 4.67
L55KN005 2.82 0.17 0.00 0.00 0.00 0.00 3.90 6.89
L55KN006 4.21 0.26 0.00 0.00 0.00 0.00 5.80 10.27
L60
L60CA010 32.24 2.83 16.23 1.97 0.00 0.00 28.86 82.13 40.30 2.90 21.46 2.60 0.00 0.00 41.25 108.51
L60CA011 35.21 3.09 16.23 1.97 0.00 0.00 31.53 88.03 44.02 3.17 21.46 2.60 0.00 0.00 45.05 116.30
L60CA013 28.67 2.60 17.31 2.10 2.36 0.36 25.79 79.19 35.83 2.66 22.89 2.77 8.21 1.26 36.85 110.47
L60JD001 13.27 1.25 12.87 1.56 2.99 0.46 12.01 44.41 16.59 1.28 17.03 2.06 10.76 1.65 17.16 66.53
L60JD002 17.71 1.64 16.34 1.98 2.99 0.46 15.98 57.10 22.13 1.68 21.61 2.62 10.76 1.65 22.83 83.28
L60JD003 13.23 1.24 12.87 1.56 2.99 0.46 11.97 44.32 16.53 1.27 17.03 2.06 10.76 1.65 17.10 66.40
L60JD004 18.86 1.82 17.31 2.10 5.96 0.91 17.14 64.10 23.57 1.86 22.89 2.77 21.47 3.28 24.49 100.33
L60JD006 16.60 1.57 18.39 2.23 4.16 0.64 15.04 58.63 20.75 1.61 24.33 2.95 14.98 2.29 21.49 88.40
L60JD007 17.81 1.68 21.64 2.62 4.16 0.64 16.12 64.67 22.26 1.72 28.62 3.47 14.98 2.29 23.04 96.38
L60JD008 34.70 3.05 18.39 2.23 0.00 0.00 31.07 89.44 43.38 3.12 24.33 2.95 0.00 0.00 44.40 118.18
M10
M10MZ001 3.54 0.18 0.00 0.00 0.00 0.00 2.10 5.82
2-284
2 232
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

M10 cont.
M10MZ003 4.13 0.21 0.00 0.00 0.00 0.00 2.46 6.80
M10MZ005 0.94 0.21 0.00 0.00 0.00 0.00 0.67 1.82
M10MZ007 1.04 0.23 0.00 0.00 0.00 0.00 0.74 2.01
M10MZ010 3.62 0.49 15.15 2.49 0.00 0.00 3.19 24.94 4.46 0.50 20.03 3.29 0.00 0.00 4.21 32.49
M10MZ011 4.66 0.63 22.72 3.74 0.00 0.00 4.11 35.86 5.74 0.64 30.05 4.94 0.00 0.00 5.42 46.79
M10SM001 4.48 0.61 33.28 4.60 0.00 0.00 3.95 46.92 5.51 0.62 43.43 6.01 0.00 0.00 5.20 60.77
M10SM003 5.22 0.71 44.37 6.14 0.00 0.00 4.60 61.04 6.42 0.72 57.90 8.01 0.00 0.00 6.06 79.11
M10SM004 5.49 0.74 55.46 7.67 0.00 0.00 4.83 74.19 6.75 0.75 72.38 10.01 0.00 0.00 6.37 96.26
M10SM005 2.02 0.27 25.51 3.53 0.00 0.00 1.78 33.11 2.48 0.28 33.29 4.60 0.00 0.00 2.34 42.99
M10SM008 3.54 0.48 44.37 6.14 0.00 0.00 3.12 57.65 4.36 0.49 57.90 8.01 0.00 0.00 4.11 74.87
M10XX001 0.21 0.05 0.00 0.00 0.00 0.00 0.15 0.41
M10XX002 0.67 0.15 0.00 0.00 0.00 0.00 0.48 1.30
M10XX003 0.81 0.18 0.00 0.00 0.00 0.00 0.57 1.56
M10XX004 1.30 0.29 0.00 0.00 0.00 0.00 0.93 2.52
M10XX005 1.98 1.17 0.00 0.00 0.00 0.00 1.34 4.49
M10XX006 2.79 1.65 0.00 0.00 0.00 0.00 1.88 6.32
M10XX007 3.55 2.10 0.00 0.00 0.00 0.00 2.40 8.05
M10XX008 4.92 2.91 0.00 0.00 0.00 0.00 3.33 11.16
M10XX009 0.89 0.12 11.09 1.53 0.00 0.00 0.78 14.41 1.09 0.12 14.48 2.00 0.00 0.00 1.03 18.72
M10XX010 2.98 0.40 8.11 1.33 0.00 0.00 2.63 15.45 3.67 0.41 10.73 1.76 0.00 0.00 3.46 20.03
M10XX011 3.42 0.46 10.82 1.78 0.00 0.00 3.02 19.50 4.21 0.47 14.31 2.35 0.00 0.00 3.97 25.31
M10XX012 3.49 0.47 10.82 1.78 0.00 0.00 3.07 19.63 4.29 0.48 14.31 2.35 0.00 0.00 4.05 25.48
M10XX013 4.52 0.61 12.44 2.05 0.00 0.00 3.98 23.60 5.56 0.62 16.46 2.71 0.00 0.00 5.24 30.59
M10XX014 6.20 0.84 18.93 3.11 0.00 0.00 5.46 34.54 7.63 0.85 25.04 4.12 0.00 0.00 7.20 44.84
M10XX015 7.77 1.05 27.05 4.45 0.00 0.00 6.85 47.17 9.57 1.07 35.77 5.88 0.00 0.00 9.03 61.32
M10XX016 8.88 1.80 0.00 0.00 0.00 0.00 7.00 17.68
M10XX017 9.39 1.90 0.00 0.00 0.00 0.00 7.40 18.69
2-285
2 233
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

M10 cont.
M10XX018 11.69 2.37 0.00 0.00 0.00 0.00 9.22 23.28
M10XX019 11.95 2.42 0.00 0.00 0.00 0.00 9.42 23.79
M10XX021 19.45 2.67 41.11 6.76 0.00 0.00 18.50 88.49 23.34 2.71 54.37 8.94 0.00 0.00 23.57 112.93
M10XX022 22.14 3.04 47.06 7.74 0.00 0.00 21.05 101.03 26.56 3.08 62.24 10.23 0.00 0.00 26.83 128.94
M10XX023 29.66 4.08 43.28 7.12 0.00 0.00 28.21 112.35 35.60 4.13 57.24 9.41 0.00 0.00 35.95 142.33
M10XX024 42.30 5.81 47.06 7.74 0.00 0.00 40.23 143.14 50.76 5.89 62.24 10.23 0.00 0.00 51.27 180.39
P10
P10IC001 12.95 1.06 18.93 2.62 0.00 0.00 17.59 53.15
P10IC002 20.38 1.66 32.46 4.49 0.00 0.00 27.68 86.67
P10IC005 54.75 4.47 86.55 11.97 0.00 0.00 74.37 232.11
P10IC010 1.84 0.15 0.00 0.00 0.00 0.00 2.50 4.49
P10IC011 3.68 0.30 1.41 0.20 0.00 0.00 5.01 10.60
P10IC012 2.59 0.21 0.00 0.00 0.00 0.00 3.51 6.31
P10IC013 4.55 0.37 2.88 0.40 0.00 0.00 6.18 14.38
P20
P20IC002 13.56 0.91 0.00 1.90 0.00 0.00 21.94 38.31
P20IC003 13.75 0.92 0.00 2.50 0.00 0.00 22.25 39.42
P20IC004 14.65 0.98 0.00 3.15 0.00 0.00 23.72 42.50
P20MK002 3.66 0.22 0.00 0.50 0.00 0.00 5.56 9.94
P20MK003 4.12 0.25 0.00 1.00 0.00 0.00 6.25 11.62
P20MK004 5.77 0.35 0.00 1.25 0.00 0.00 8.76 16.13
P20MK005 8.90 0.55 0.00 1.25 0.00 0.00 13.51 24.21
P20MK006 12.09 0.74 0.00 2.50 0.00 0.00 18.35 33.68
P20MK007 13.68 0.84 0.00 2.50 0.00 0.00 20.77 37.79
2-286
2 234
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

P25
P25DL001 3.54 0.22 2.27 1.26 0.00 0.00 4.89 12.18
P25DL003 4.58 0.28 5.84 2.01 0.00 0.00 6.32 19.03
P25DL004 5.01 0.31 7.36 2.82 0.00 0.00 6.91 22.41
P25DL005 8.68 0.53 11.36 4.22 0.00 0.00 11.98 36.77
P25DL006 8.44 0.52 12.87 5.08 0.00 0.00 11.65 38.56
P25DL008 10.87 0.67 21.21 8.23 0.00 0.00 15.00 55.98
P25DL009 16.21 0.99 26.94 10.33 0.00 0.00 22.37 76.84
P25DL010 30.37 1.86 31.38 12.59 0.00 0.00 41.92 118.12
P25DL011 45.84 2.81 39.16 15.32 0.00 0.00 63.26 166.39
P25IC001 9.91 0.61 3.25 2.65 0.00 0.00 13.67 30.09
P25IC002 11.02 0.68 5.08 4.15 0.00 0.00 15.20 36.13
P25IC003 15.83 0.97 8.11 5.52 0.00 0.00 21.84 52.27
P25IC004 17.54 1.07 9.95 6.68 0.00 0.00 24.21 59.45
P25IC005 21.88 1.34 12.44 7.97 0.00 0.00 30.19 73.82
P25IC006 27.05 1.66 14.93 9.27 0.00 0.00 37.33 90.24
P25MK001 8.45 0.52 4.00 3.05 0.00 0.00 11.66 27.68
P25MK003 13.07 0.80 8.44 5.32 0.00 0.00 18.04 45.67
P25VU002 10.93 0.61 0.00 2.50 0.00 0.00 14.20 28.24
P25VU003 13.46 0.76 0.00 2.50 0.00 0.00 17.48 34.20
P25VU004 13.74 0.77 0.00 2.50 0.00 0.00 17.85 34.86
P25VU005 18.47 1.04 0.00 2.50 0.00 0.00 23.98 45.99
P25VU010 18.97 1.06 0.00 0.95 0.00 0.00 24.64 45.62
P25VU011 19.22 1.08 0.00 1.17 0.00 0.00 24.96 46.43
P30
P30MK001 14.12 0.87 20.02 2.77 0.00 0.00 19.48 57.26
P30MK003 23.96 1.47 35.16 4.86 0.00 0.00 33.07 98.52
2-287
2 235
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

P30 cont.
P30MK004 41.01 2.51 68.16 9.43 0.00 0.00 56.59 177.70
P35
P35CA010 18.31 2.41 7.42 1.29 0.00 0.00 24.40 53.83 22.29 2.44 9.60 1.66 0.00 0.00 34.38 70.37
P35CA011 46.24 6.08 18.39 3.19 0.00 0.00 61.62 135.52 56.30 6.17 23.80 4.13 0.00 0.00 86.84 177.24
P35CA012 54.91 7.22 21.71 3.76 0.00 0.00 73.17 160.77 66.85 7.32 28.10 4.87 0.00 0.00 103.11 210.25
P40
P40GJ016 1.54 0.10 0.05 0.07 0.06 0.01 1.46 3.29
P40TE003 10.12 0.69 2.68 0.32 1.65 0.25 9.65 25.36
P40TE004 11.67 0.79 3.69 0.45 1.62 0.25 11.12 29.59
P40TE005 8.86 0.61 5.53 0.67 1.65 0.25 8.46 26.03
P40TE006 11.95 0.81 5.53 0.67 1.73 0.26 11.39 32.34
P40TE007 20.31 1.37 5.53 0.67 1.73 0.26 19.34 49.21
P40TE008 22.66 1.52 6.37 0.77 1.73 0.26 21.56 54.87
P40TE009 25.37 1.70 6.37 0.77 1.73 0.26 24.15 60.35
P40TE010 8.60 0.58 17.59 2.13 0.75 0.11 8.19 37.95
P40TE011 9.35 0.64 17.59 2.13 1.27 0.19 8.92 40.09
P40TE012 14.14 0.96 17.59 2.13 1.27 0.19 13.47 49.75
P40TE013 12.92 0.88 17.59 2.13 1.27 0.19 12.31 47.29
P40TE014 13.17 0.89 17.59 2.13 1.27 0.19 12.55 47.79
P40TE015 15.02 1.01 17.59 2.13 1.27 0.19 14.30 51.51
P45
P45AF002 0.10 0.01 0.00 0.00 0.00 0.00 0.13 0.24
P45AF003 0.15 0.01 0.00 0.00 0.00 0.00 0.19 0.35
P45AF006 1.14 0.09 3.88 0.54 0.22 0.03 1.50 7.40
P45AF007 1.50 0.11 8.08 1.12 0.14 0.02 1.96 12.93
2-288
2 236
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

P45 cont.
P45AF008 0.90 0.06 0.00 0.10 0.00 0.00 1.17 2.23
P45AF009 1.99 0.14 1.57 0.29 0.00 0.00 2.58 6.57
P45AF010 6.63 0.48 7.22 0.87 0.11 0.02 8.63 23.96
P45AF011 6.04 0.44 9.42 1.14 0.11 0.02 7.86 25.03
P45AL015 6.97 0.51 7.22 0.87 0.11 0.02 9.06 24.76
P45CG001 0.46 0.03 0.00 0.05 0.00 0.00 0.60 1.14
P45CG002 0.76 0.05 0.00 0.10 0.00 0.00 0.98 1.89
P45CG003 1.72 0.12 0.00 0.15 0.00 0.00 2.24 4.23
P45CG006 3.15 0.23 5.17 0.72 0.11 0.02 4.10 13.50
P45CG007 2.57 0.19 5.17 0.72 0.00 0.00 3.34 11.99
P45OE002 3.20 0.23 8.64 1.05 0.10 0.02 4.17 17.41
P45OE003 4.25 0.31 13.19 1.60 0.10 0.02 5.53 25.00
P45OE004 5.00 0.36 18.85 2.28 0.10 0.02 6.50 33.11
P45OE005 8.31 0.61 28.43 3.45 0.20 0.03 10.81 51.84
P50
P50GR001 0.03 0.00 0.00 0.00 0.00 0.00 0.05 0.08
P50GR002 0.04 0.00 0.00 0.00 0.00 0.00 0.08 0.12
P50GR003 0.07 0.00 0.00 0.00 0.00 0.00 0.14 0.21
P50GR004 0.16 0.01 0.00 0.00 0.00 0.00 0.29 0.46
P50GR005 0.02 0.00 0.00 0.00 0.00 0.00 0.04 0.06
P50GR006 0.04 0.00 0.00 0.00 0.00 0.00 0.07 0.11
P50GR007 0.06 0.00 0.00 0.00 0.00 0.00 0.11 0.17
P50GR008 0.11 0.00 0.00 0.00 0.00 0.00 0.21 0.32
P50WC001 0.11 0.01 3.05 0.42 0.00 0.00 0.14 3.73
P50WC002 0.13 0.01 2.25 0.37 0.00 0.00 0.16 2.92
P50WC003 0.34 0.03 2.40 0.39 0.00 0.00 0.43 3.59
P50WC004 1.39 0.11 4.95 0.81 0.05 0.01 1.73 9.05
2-289
2 237
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

P50 cont.
P50XX001 4.87 0.38 9.00 1.48 0.00 0.00 6.05 21.78
P50XX002 4.57 0.36 10.50 1.73 0.00 0.00 5.68 22.84
P50XX003 8.47 0.67 12.76 2.10 0.00 0.00 10.52 34.52
P55
P55GF001 2.19 0.17 3.15 0.52 0.00 0.00 3.02 9.05
P55GF002 3.13 0.25 10.81 1.78 0.00 0.00 4.32 20.29
P55GR001 0.46 0.03 0.17 0.08 0.00 0.00 0.36 1.10
P55GR002 0.56 0.04 0.43 0.21 0.00 0.00 0.43 1.67
P55GR003 1.50 0.11 2.14 1.04 0.00 0.00 1.17 5.96
P55GR004 2.20 0.16 5.13 2.50 0.00 0.00 1.71 11.70
P55WC001 0.03 0.00 0.09 0.04 0.00 0.00 0.02 0.18
P55WC002 0.06 0.00 0.09 0.04 0.00 0.00 0.05 0.24
P60
P60GF003 2.50 0.20 3.15 0.52 0.11 0.02 3.12 9.62
P60GF004 3.02 0.24 10.81 1.78 0.11 0.02 3.76 19.74
P60GF005 4.01 0.32 16.96 2.79 0.11 0.02 4.99 29.20
P60GF006 4.85 0.39 21.01 3.45 0.13 0.02 6.03 35.88
P60GF008 3.45 0.28 10.81 1.78 0.11 0.02 4.29 20.74
P60GR001 2.61 0.21 7.05 1.16 0.10 0.02 3.25 14.40
P60GR002 3.05 0.25 30.76 4.25 0.10 0.02 3.80 42.23
P60HO002 0.09 0.01 1.07 0.15 0.00 0.00 0.11 1.43
P60HO003 0.18 0.01 2.44 0.34 0.00 0.00 0.22 3.19
P60WC001 0.05 0.00 1.22 0.17 0.00 0.00 0.06 1.50
P60WC002 0.05 0.00 1.83 0.25 0.00 0.00 0.07 2.20
2-290
2 238
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

P65
P65GR001 0.38 0.04 1.52 0.21 0.18 0.03 0.44 2.80
P65GR002 0.46 0.04 0.46 0.06 0.18 0.03 0.53 1.76
P65GR003 1.24 0.11 0.91 0.13 0.20 0.03 1.39 4.01
P65HO001 0.16 0.01 1.07 0.15 0.00 0.00 0.20 1.59
P65HO002 0.18 0.01 1.07 0.15 0.00 0.00 0.23 1.64
P65WC001 0.16 0.01 1.22 0.17 0.00 0.00 0.17 1.73
P65WC002 0.17 0.01 1.22 0.17 0.00 0.00 0.19 1.76
P70
P70XX001 0.35 0.03 0.61 0.08 0.00 0.00 0.41 1.48
P70XX002 0.91 0.08 1.83 0.25 0.00 0.00 1.07 4.14
R10
R10CA001 1.08 0.09 0.00 0.08 0.00 0.00 1.36 2.61 1.33 0.09 0.00 0.08 0.00 0.00 1.86 3.36
R10CA003 1.08 0.09 0.00 0.08 0.00 0.00 1.36 2.61 1.33 0.09 0.00 0.08 0.00 0.00 1.86 3.36
R10CA005 1.08 0.09 0.00 0.08 0.00 0.00 1.36 2.61 1.33 0.09 0.00 0.08 0.00 0.00 1.86 3.36
R10CA006 0.03 0.00 0.00 0.00 0.00 0.00 0.04 0.07 0.04 0.00 0.00 0.00 0.00 0.00 0.05 0.09
R10CA007 1.72 0.14 0.00 0.08 0.00 0.00 2.17 4.11 2.11 0.14 0.00 0.08 0.00 0.00 2.97 5.30
R10CA009 4.54 0.36 0.00 0.08 0.00 0.00 5.73 10.71 5.58 0.37 0.00 0.08 0.00 0.00 7.83 13.86
R10CA010 0.20 0.02 0.00 0.00 0.00 0.00 0.25 0.47 0.24 0.02 0.00 0.00 0.00 0.00 0.34 0.60
R10CA011 5.07 0.40 0.00 0.10 0.00 0.00 6.40 11.97 6.24 0.41 0.00 0.10 0.00 0.00 8.75 15.50
R10CA012 6.22 0.49 0.00 0.10 0.00 0.00 7.85 14.66 7.65 0.50 0.00 0.10 0.00 0.00 10.73 18.98
R10CA013 0.43 0.03 0.00 0.00 0.00 0.00 0.55 1.01 0.53 0.04 0.00 0.00 0.00 0.00 0.75 1.32
R10CA014 6.78 0.54 0.00 0.16 0.00 0.00 8.56 16.04 8.35 0.55 0.00 0.16 0.00 0.00 11.71 20.77
R10CA015 8.75 0.69 0.00 0.16 0.00 0.00 11.05 20.65 10.77 0.71 0.00 0.16 0.00 0.00 15.10 26.74
R10CA016 0.43 0.03 0.00 0.00 0.00 0.00 0.55 1.01 0.53 0.04 0.00 0.00 0.00 0.00 0.75 1.32
R10CA017 11.46 0.90 0.00 0.21 0.00 0.00 14.47 27.04 14.11 0.93 0.00 0.21 0.00 0.00 19.79 35.04
2-291
2 239
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

R10 cont.
R10CA018 13.87 1.09 0.00 0.22 0.00 0.00 17.51 32.69 17.07 1.12 0.00 0.22 0.00 0.00 23.94 42.35
R10CA019 0.82 0.06 0.00 0.24 0.00 0.00 1.04 2.16 1.01 0.07 0.00 0.24 0.00 0.00 1.42 2.74
R10CA020 13.74 1.08 0.00 0.23 0.00 0.00 17.35 32.40 16.91 1.11 0.00 0.23 0.00 0.00 23.72 41.97
R10CA021 14.01 1.11 0.00 0.25 0.00 0.00 17.69 33.06 17.24 1.13 0.00 0.25 0.00 0.00 24.18 42.80
R10CA022 0.12 0.01 0.00 0.00 0.00 0.00 0.15 0.28 0.15 0.01 0.00 0.00 0.00 0.00 0.21 0.37
R10CA023 0.12 0.01 0.00 0.00 0.00 0.00 0.15 0.28 0.15 0.01 0.00 0.00 0.00 0.00 0.21 0.37
R15
R15SO001 10.47 1.17 0.00 0.40 1.99 0.30 10.24 24.57
R15SO002 8.39 1.29 0.00 0.45 5.87 0.90 8.90 25.80
R15SO003 13.83 1.82 0.00 0.67 5.87 0.90 14.06 37.15
R20
R20SO001 6.70 0.65 0.00 0.25 0.00 0.00 7.26 14.86
R30
R30BO003 14.77 1.13 14.59 1.51 2.06 0.32 13.30 47.68
R30BO004 7.36 0.60 11.27 1.17 2.22 0.34 6.70 29.66
R30BO005 7.28 0.64 6.23 0.65 0.00 0.00 7.42 22.22
R30BO006 7.93 0.70 11.01 1.14 0.00 0.00 8.08 28.86
R30BO007 9.24 0.81 10.34 1.07 0.00 0.00 9.41 30.87
R30BO008 38.21 4.35 58.62 6.07 0.00 0.00 41.36 148.61
R30BO009 37.15 4.23 58.62 6.07 0.00 0.00 40.21 146.28
R30CA003 33.78 3.85 31.83 3.30 0.00 0.00 36.57 109.33
R30CA006 48.76 5.56 41.78 4.33 0.00 0.00 52.78 153.21
R30CA010 8.85 0.65 9.28 0.96 0.61 0.09 7.92 28.36
R30CA012 33.49 3.82 29.18 3.02 0.00 0.00 36.25 105.76
R30CA013 51.11 5.82 41.78 4.33 0.00 0.00 55.32 158.36
2-292
2 240
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

R30 cont.
R30CA014 15.23 1.18 13.93 1.44 5.21 0.80 13.75 51.54
R30RS001 1.41 0.12 4.33 0.45 0.00 0.00 1.44 7.75
R30RS002 2.83 0.25 5.30 0.55 0.00 0.00 2.88 11.81
R30RS003 7.41 0.56 10.61 1.10 0.85 0.13 6.66 27.32
R30SI002 12.13 0.94 12.07 1.25 2.01 0.31 10.94 39.65
R30SI003 15.31 1.17 12.60 1.31 2.01 0.31 13.78 46.49
R30SI004 20.81 1.55 14.32 1.48 1.58 0.24 18.65 58.63
R30SI005 11.18 0.98 9.95 1.03 0.00 0.00 11.39 34.53
R40
R40BO001 6.84 0.54 7.50 1.04 0.00 0.00 7.40 23.32
R40BO002 7.41 0.58 7.50 1.04 0.00 0.00 8.02 24.55
R45
R45BO004 4.12 0.33 4.95 0.68 0.00 0.00 6.13 16.21
R45BO005 6.06 0.48 6.90 0.95 0.00 0.00 9.01 23.40
R45BO006 12.22 0.96 16.21 2.24 0.00 0.00 18.17 49.80
R45BO007 13.96 1.10 19.66 2.72 0.00 0.00 20.77 58.21
R45BO008 15.63 1.23 30.76 4.25 0.00 0.00 23.24 75.11
R45CA001 5.31 0.42 4.80 0.66 0.00 0.00 7.89 19.08
R45CA005 12.50 0.99 10.50 1.45 0.00 0.00 18.59 44.03
R45CA011 4.08 0.32 4.95 0.68 0.00 0.00 6.06 16.09
R45CA012 14.33 1.13 20.56 2.84 0.00 0.00 21.31 60.17
R45CA013 19.09 1.51 20.56 2.84 0.00 0.00 28.40 72.40
R45RS001 2.13 0.17 3.00 0.41 0.00 0.00 3.17 8.88
R45SI008 4.13 0.33 5.25 0.73 0.00 0.00 6.14 16.58
R45SI009 11.18 0.88 11.71 1.62 0.00 0.00 16.63 42.02
R45SI010 15.06 1.19 19.06 2.64 0.00 0.00 22.39 60.34
2-293
2 241
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

R50
R50BO005 4.95 0.48 5.41 0.75 1.58 0.24 7.36 20.77
R50BO006 8.10 0.71 8.11 1.12 0.20 0.03 11.72 29.99
R50BO007 9.31 0.82 8.11 1.12 0.52 0.08 13.50 33.46
R50BO008 15.71 1.42 16.77 2.32 1.58 0.24 22.89 60.93
R50BO009 14.35 1.30 21.10 2.92 1.58 0.24 20.92 62.41
R50BO010 5.61 0.50 5.41 0.75 0.36 0.06 8.14 20.83
R50BO011 8.55 0.75 8.11 1.12 0.20 0.03 12.37 31.13
R50BO012 10.99 0.97 10.93 1.51 0.52 0.08 15.93 40.93
R50BO013 16.53 1.49 14.17 1.96 1.58 0.24 24.08 60.05
R50CA001 8.47 0.75 7.57 1.05 0.39 0.06 12.27 30.56
R50CA002 9.39 0.83 7.57 1.05 0.39 0.06 13.61 32.90
R50CA005 11.87 1.05 10.82 1.50 0.66 0.10 17.22 43.22
R50CA006 9.31 0.86 8.98 1.24 1.43 0.22 13.63 35.67
R50CA007 15.37 1.38 16.88 2.33 1.43 0.22 22.37 59.98
R50CA008 18.05 1.61 16.88 2.33 1.43 0.22 26.25 66.77
R50CA011 20.29 1.81 16.23 2.24 1.43 0.22 29.48 71.70
R50CA013 13.02 1.15 10.82 1.50 0.59 0.09 18.87 46.04
R50CA014 15.65 1.38 10.82 1.50 0.59 0.09 22.66 52.69
R50CA015 24.64 2.18 16.99 2.35 1.43 0.22 35.74 83.55
R50CA016 25.09 2.22 16.99 2.35 1.43 0.22 36.39 84.69
R50IP001 9.24 0.83 8.66 1.20 0.85 0.13 13.46 34.37
R50SI006 7.41 0.69 6.49 0.90 1.50 0.23 10.90 28.12
R50SI007 7.98 0.74 6.49 0.90 1.50 0.23 11.72 29.56
R50SI013 12.51 1.14 16.01 2.21 1.58 0.24 18.26 51.95
R50SI016 13.46 1.22 16.01 2.21 1.58 0.24 19.65 54.37
R50SI017 14.61 1.32 16.01 2.21 1.58 0.24 21.30 57.27
R50SI022 10.60 0.94 10.82 1.50 0.64 0.10 15.38 39.98
2-294
2 242
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

R50 cont.
R50SI023 11.98 1.06 10.82 1.50 0.64 0.10 17.37 43.47
R50SI024 5.93 0.53 3.03 0.42 0.47 0.07 8.62 19.07
R50SI025 7.36 0.65 3.25 0.45 0.47 0.07 10.68 22.93
R50SI026 14.80 1.30 11.25 1.56 0.47 0.07 21.41 50.86
R55
R55GL001 0.68 0.04 0.00 0.50 0.03 0.00 0.72 1.97
R55GL002 0.91 0.06 1.02 0.61 0.07 0.01 0.96 3.64
R55GL003 2.57 0.15 1.83 0.94 0.06 0.01 2.68 8.24
R55GL004 3.15 0.18 1.83 1.19 0.05 0.01 3.28 9.69
R55GL007 2.05 0.12 3.65 0.38 0.00 0.00 2.13 8.33
R55GL009 0.47 0.03 2.13 0.22 0.00 0.00 0.48 3.33
R55GL011 1.16 0.07 3.25 0.34 0.00 0.00 1.21 6.03
R55GL012 1.78 0.10 1.83 0.94 0.07 0.01 1.86 6.59
R55GL013 0.13 0.02 0.00 0.25 0.14 0.02 0.16 0.72
R55GL014 0.61 0.03 0.00 0.35 0.00 0.00 0.64 1.63
R55GL015 1.93 0.11 1.83 0.19 0.00 0.00 2.00 6.06
R55GL016 0.82 0.05 1.83 0.19 0.00 0.00 0.85 3.74
R55GL017 0.36 0.02 1.02 0.11 0.00 0.00 0.37 1.88
R55GL018 0.41 0.02 1.02 0.11 0.00 0.00 0.42 1.98
R55GL019 0.79 0.04 1.62 0.17 0.00 0.00 0.82 3.44
R55GL020 0.60 0.04 1.02 0.11 0.15 0.02 0.64 2.58
R55GL021 0.43 0.02 1.83 0.19 0.00 0.00 0.45 2.92
R55GL022 3.92 0.23 1.62 7.17 0.24 0.04 4.11 17.33
R55GL023 1.18 0.07 1.62 0.17 0.08 0.01 1.24 4.37
R55GL024 0.84 0.05 1.12 0.12 0.00 0.00 0.87 3.00
R55GL025 0.62 0.03 1.32 0.14 0.00 0.00 0.64 2.75
2-295
2 243
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

S10
S10CA001 24.67 2.48 18.93 3.27 4.03 0.62 32.49 86.49 30.83 2.54 25.04 4.33 16.30 2.49 45.12 126.65
S10CA003 27.90 4.11 39.49 5.46 14.08 2.15 41.93 135.12 31.54 4.14 52.23 7.22 56.89 8.70 49.90 210.62
S15
S15CA001 30.78 4.62 36.94 5.11 14.08 2.15 36.24 129.92 36.94 4.67 47.13 6.52 56.89 8.70 46.20 207.05
S15CA002 44.98 6.77 45.54 6.30 21.44 3.28 52.98 181.29 53.97 6.84 58.11 8.04 86.64 13.26 67.55 294.41
S15JU001 32.73 4.76 42.71 5.91 4.99 0.76 38.28 130.14 39.28 4.81 54.49 7.54 18.58 2.84 48.80 176.34
S15JU002 33.91 4.93 42.71 5.91 4.99 0.76 39.65 132.86 40.70 4.98 54.49 7.54 18.58 2.84 50.55 179.68
S20
S20CA001 25.45 3.87 58.11 6.54 17.69 2.71 31.93 146.30 28.28 3.90 75.54 8.51 74.86 11.45 37.56 240.10
S20CA002 37.61 5.58 58.11 6.54 17.69 2.71 46.93 175.17 41.79 5.62 75.54 8.51 74.86 11.45 55.21 272.98
S20CA003 58.42 8.66 73.30 8.26 26.95 4.12 72.87 252.58 64.91 8.71 95.28 10.73 114.00 17.44 85.72 396.79
S20CA004 60.97 9.02 73.30 8.26 26.95 4.12 76.02 258.64 67.75 9.07 95.28 10.73 114.00 17.44 89.43 403.70
S20CA005 75.60 11.10 99.47 11.21 28.49 4.36 94.11 324.34 84.00 11.17 129.30 14.56 120.55 18.44 110.71 488.73
S20CA006 79.85 11.77 99.47 11.21 33.12 5.07 99.50 339.99 88.73 11.85 129.30 14.56 140.12 21.44 117.05 523.05
S25
S25JD001 3.16 0.43 0.00 1.50 1.40 0.21 3.34 10.04 3.79 0.44 0.00 1.50 5.22 0.80 4.29 16.04
S25JD002 4.05 0.56 0.00 1.50 3.39 0.52 4.29 14.31 4.86 0.57 0.00 1.50 12.63 1.93 5.51 27.00
S25RI001 2.95 0.37 0.00 1.50 0.96 0.15 3.05 8.98 3.54 0.37 0.00 1.50 3.58 0.55 3.92 13.46
S25RI002 3.21 0.41 0.00 1.50 1.44 0.22 3.35 10.13 3.85 0.42 0.00 1.50 5.38 0.82 4.30 16.27
S25RM001 8.24 1.05 0.00 1.50 3.94 0.60 8.57 23.90 9.89 1.06 0.00 1.50 14.51 2.22 11.01 40.19
S25RM002 11.40 1.55 0.00 1.50 8.94 1.37 12.03 36.79 13.67 1.57 0.00 1.50 33.08 5.06 15.46 70.34
S25RM003 5.97 0.79 0.00 1.50 3.94 0.60 6.26 19.06 7.17 0.80 0.00 1.50 14.51 2.22 8.05 34.25
S25RM004 8.91 1.28 0.00 1.50 8.92 1.36 9.53 31.50 10.69 1.30 0.00 1.50 32.91 5.04 12.25 63.69
2-296
2 244
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

S30
S30HW001 12.61 2.46 15.44 7.51 1.78 0.27 15.52 55.59 21.01 2.53 18.53 10.91 2.00 0.31 32.34 87.63
S30HW002 17.08 3.31 21.61 10.51 2.20 0.34 21.02 76.07 28.47 3.42 25.94 15.27 2.46 0.38 43.80 119.74
S30HW005 6.74 1.32 2.47 1.20 1.07 0.16 5.39 18.35 11.23 1.36 2.96 1.74 1.21 0.19 11.76 30.45
S30HW006 11.40 2.20 6.18 3.01 1.15 0.18 9.10 33.22 19.00 2.27 7.41 4.36 1.29 0.20 19.85 54.38
S30HW007 12.42 2.39 7.72 3.76 1.15 0.18 9.92 37.54 20.69 2.46 9.26 5.45 1.29 0.20 21.62 60.97
S30HW008 12.99 2.50 7.72 3.76 1.15 0.18 10.37 38.67 21.64 2.57 9.26 5.45 1.29 0.20 22.61 63.02
S30HW009 13.33 2.59 9.26 4.51 1.69 0.26 10.66 42.30 22.21 2.67 11.12 6.54 1.89 0.29 23.23 67.95
S30HW010 16.30 3.15 12.35 6.01 1.87 0.29 13.03 53.00 27.17 3.25 14.82 8.72 2.10 0.32 28.41 84.79
S30HW011 15.95 3.09 12.35 6.01 1.97 0.30 12.75 52.42 26.58 3.19 14.82 8.72 2.21 0.34 27.79 83.65
S30HW012 18.89 3.65 12.35 6.01 2.20 0.34 15.10 58.54 31.49 3.77 14.82 8.72 2.46 0.38 32.92 94.56
S30HW013 15.19 2.94 27.79 13.52 1.74 0.27 18.70 80.15 25.32 3.03 33.35 19.63 1.95 0.30 38.95 122.53
S30HW014 12.28 1.02 0.93 0.45 0.71 0.11 12.09 27.59 15.34 1.05 1.11 0.65 0.79 0.12 18.90 37.96
S30HW015 13.52 1.12 1.54 0.75 0.71 0.11 13.31 31.06 16.90 1.15 1.85 1.09 0.79 0.12 20.80 42.70
S30HW016 12.78 1.06 1.24 0.60 0.71 0.11 12.58 29.08 15.97 1.09 1.48 0.87 0.79 0.12 19.67 39.99
S30HW017 13.75 1.14 1.54 0.75 0.71 0.11 13.53 31.53 17.18 1.17 1.85 1.09 0.79 0.12 21.15 43.35
S30HW018 16.05 1.36 2.47 1.20 1.29 0.20 15.83 38.40 20.06 1.39 2.96 1.74 1.46 0.22 24.74 52.57
S30KB001 3.17 0.29 0.62 0.30 0.63 0.10 2.76 7.87 3.96 0.30 0.74 0.44 0.71 0.11 4.18 10.44
S30KB002 4.11 0.37 0.93 0.45 0.79 0.12 3.58 10.35 5.14 0.38 1.11 0.65 0.88 0.13 5.43 13.72
S30KB003 3.51 0.30 1.24 0.60 0.44 0.07 3.04 9.20 4.39 0.31 1.48 0.87 0.50 0.08 4.61 12.24
S30KB004 4.93 0.47 1.54 0.75 1.30 0.20 4.31 13.50 6.16 0.48 1.85 1.09 1.46 0.22 6.53 17.79
S30KB005 3.86 0.36 1.54 0.75 0.89 0.14 3.37 10.91 4.83 0.37 1.85 1.09 1.00 0.15 5.11 14.40
S30KB006 5.66 0.53 1.85 0.90 1.38 0.21 4.94 15.47 7.07 0.54 2.22 1.31 1.55 0.24 7.49 20.42
S30KB007 3.70 0.33 0.62 0.30 0.63 0.10 3.22 8.90 4.63 0.34 0.74 0.44 0.71 0.11 4.88 11.85
S30KB008 4.61 0.41 0.93 0.45 0.69 0.11 4.00 11.20 5.76 0.42 1.11 0.65 0.78 0.12 6.07 14.91
S30KB009 6.14 0.56 0.93 0.45 1.32 0.20 5.35 14.95 7.67 0.58 1.11 0.65 1.48 0.23 8.11 19.83
S30KB010 3.78 0.35 1.24 0.60 0.82 0.13 3.29 10.21 4.72 0.36 1.48 0.87 0.92 0.14 4.99 13.48
S30KB011 5.59 0.50 1.54 0.75 0.90 0.14 4.85 14.27 6.98 0.51 1.85 1.09 1.01 0.15 7.36 18.95
2-297
2 245
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

S30 cont.
S30KB012 6.52 0.60 1.54 0.75 1.42 0.22 5.68 16.73 8.15 0.62 1.85 1.09 1.59 0.24 8.62 22.16
S30KB013 4.42 0.40 1.54 0.75 0.89 0.14 3.85 11.99 5.52 0.41 1.85 1.09 1.00 0.15 5.83 15.85
S30KB014 6.04 0.54 1.85 0.90 0.98 0.15 5.24 15.70 7.55 0.55 2.22 1.31 1.10 0.17 7.95 20.85
S30KB015 8.04 0.73 2.47 1.20 1.52 0.23 7.00 21.19 10.06 0.75 2.96 1.74 1.70 0.26 10.61 28.08
S30KB018 9.76 0.83 1.54 0.75 0.94 0.14 8.44 22.40 12.20 0.85 1.85 1.09 1.05 0.16 12.80 30.00
S30KB021 11.33 0.96 2.47 1.20 1.06 0.16 9.79 26.97 14.17 0.99 2.96 1.74 1.18 0.18 14.86 36.08
S30KB024 13.00 1.10 3.71 1.81 1.17 0.18 11.24 32.21 16.26 1.13 4.45 2.62 1.31 0.20 17.04 43.01
S30KB025 6.86 0.59 1.24 0.60 0.79 0.12 5.93 16.13 8.57 0.61 1.48 0.87 0.88 0.13 9.00 21.54
S30KB026 8.21 0.70 1.24 0.60 0.85 0.13 7.10 18.83 10.26 0.72 1.48 0.87 0.95 0.15 10.77 25.20
S30KB027 10.47 0.89 1.54 0.75 0.94 0.14 9.05 23.78 13.09 0.91 1.85 1.09 1.05 0.16 13.72 31.87
S30KB028 7.82 0.67 1.85 0.90 0.86 0.13 6.76 18.99 9.77 0.69 2.22 1.31 0.96 0.15 10.26 25.36
S30KB029 9.48 0.81 1.85 0.90 0.94 0.14 8.19 22.31 11.85 0.83 2.22 1.31 1.05 0.16 12.43 29.85
S30KB030 11.99 1.02 2.47 1.20 1.06 0.16 10.36 28.26 14.99 1.04 2.96 1.74 1.18 0.18 15.71 37.80
S30KB031 10.28 0.87 3.09 1.50 0.94 0.14 8.88 25.70 12.85 0.90 3.71 2.18 1.05 0.16 13.47 34.32
S30KB032 12.15 1.03 3.09 1.50 1.06 0.16 10.49 29.48 15.18 1.06 3.71 2.18 1.18 0.18 15.91 39.40
S30KB033 14.04 1.19 3.71 1.81 1.17 0.18 12.12 34.22 17.55 1.22 4.45 2.62 1.31 0.20 18.39 45.74
S30KB034 4.89 0.44 0.93 0.45 0.86 0.13 4.25 11.95 6.11 0.45 1.11 0.65 0.96 0.15 6.44 15.87
S30KB035 5.56 0.50 1.24 0.60 1.02 0.16 4.83 13.91 6.95 0.51 1.48 0.87 1.14 0.17 7.33 18.45
S30KB036 5.23 0.47 1.24 0.60 0.94 0.14 4.55 13.17 6.54 0.48 1.48 0.87 1.05 0.16 6.90 17.48
S30KB041 5.96 0.54 1.24 0.60 1.12 0.17 5.18 14.81 7.45 0.55 1.48 0.87 1.26 0.19 7.86 19.66
S30KB042 8.74 0.74 1.85 0.90 0.79 0.12 7.55 20.69 10.92 0.76 2.22 1.31 0.88 0.13 11.45 27.67
S30KB043 13.13 1.10 0.93 0.45 0.85 0.13 11.33 27.92 16.41 1.13 1.11 0.65 0.95 0.15 17.18 37.58
S30KB044 16.25 1.35 0.93 0.45 0.85 0.13 14.01 33.97 20.32 1.38 1.11 0.65 0.95 0.15 21.25 45.81
S30KB045 22.04 4.20 38.95 4.72 1.34 0.21 27.08 98.54 36.74 4.34 46.49 6.75 1.50 0.23 56.42 152.47
S30KB046 15.21 2.94 16.80 8.17 1.64 0.25 22.45 67.46 25.36 3.03 20.16 11.87 1.84 0.28 49.90 112.44
S30KB047 19.17 3.66 19.45 9.46 1.24 0.19 28.25 81.42 31.95 3.77 23.34 13.74 1.39 0.21 62.81 137.21
S30KB048 16.48 1.37 5.25 2.55 0.97 0.15 16.23 43.00 20.60 1.41 6.30 3.71 1.08 0.17 25.37 58.64
2-298
2 246
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

S30 cont.
S30KB049 18.41 1.62 5.56 2.71 2.82 0.43 18.23 49.78 23.01 1.66 6.67 3.93 3.17 0.49 28.50 67.43
S30KB050 23.80 1.96 15.44 7.51 0.89 0.14 23.41 73.15 29.74 2.01 18.53 10.91 1.00 0.15 36.58 98.92
S30KB051 30.14 2.49 15.44 7.51 1.34 0.21 29.66 86.79 37.68 2.56 18.53 10.91 1.50 0.23 46.36 117.77
S30KB052 32.13 2.60 15.44 7.51 0.45 0.07 31.55 89.75 40.16 2.67 18.53 10.91 0.50 0.08 49.31 122.16
S30KB053 9.00 0.77 2.47 1.20 0.85 0.13 7.78 22.20 11.26 0.79 2.96 1.74 0.95 0.15 11.80 29.65
S30KB054 8.95 0.76 0.93 0.45 0.79 0.12 7.74 19.74 11.19 0.78 1.11 0.65 0.88 0.13 11.73 26.47
S30KB055 14.24 2.73 26.51 3.21 1.15 0.18 11.37 59.39 23.73 2.81 31.64 4.60 1.29 0.20 24.78 89.05
S30KB056 14.60 2.80 26.51 3.21 1.15 0.18 11.65 60.10 24.33 2.88 31.64 4.60 1.29 0.20 25.41 90.35
S30KB057 16.32 3.12 26.51 3.21 1.15 0.18 13.03 63.52 27.21 3.22 31.64 4.60 1.29 0.20 28.41 96.57
S30KB058 15.22 2.91 8.03 3.91 1.18 0.18 12.15 43.58 25.37 3.00 9.63 5.67 1.32 0.20 26.50 71.69
S30KB059 23.98 4.58 18.53 9.02 1.62 0.25 19.14 77.12 39.97 4.72 22.23 13.08 1.82 0.28 41.74 123.84
S30PU002 54.98 4.47 43.28 5.24 1.49 0.23 47.29 156.98 68.72 4.59 51.65 7.50 1.77 0.27 71.73 206.23
S30PU003 69.26 5.62 43.28 5.24 1.65 0.25 59.56 184.86 86.57 5.77 51.65 7.50 1.94 0.30 90.34 244.07
S30PU004 81.42 6.59 43.28 5.24 1.65 0.25 70.01 208.44 101.78 6.78 51.65 7.50 1.94 0.30 106.19 276.14
S30RA002 6.98 0.57 2.70 0.33 0.24 0.04 6.86 17.72 8.72 0.59 3.23 0.47 0.27 0.04 10.72 24.04
S30RA003 10.97 0.91 5.30 0.64 0.48 0.07 10.80 29.17 13.72 0.93 6.33 0.92 0.53 0.08 16.88 39.39
S30TS001 3.44 0.30 0.74 0.36 0.51 0.08 2.98 8.41 4.30 0.31 0.89 0.52 0.57 0.09 4.52 11.20
S30TS002 4.70 0.41 1.05 0.51 0.63 0.10 4.08 11.48 5.88 0.42 1.26 0.74 0.71 0.11 6.18 15.30
S30TS003 3.52 0.31 1.05 0.51 0.58 0.09 3.06 9.12 4.40 0.32 1.26 0.74 0.65 0.10 4.64 12.11
S30TS004 4.81 0.42 1.36 0.66 0.74 0.11 4.17 12.27 6.01 0.43 1.63 0.96 0.83 0.13 6.33 16.32
S30TS005 3.68 0.33 1.36 0.66 0.66 0.10 3.19 9.98 4.60 0.34 1.63 0.96 0.74 0.11 4.85 13.23
S30TS006 5.01 0.44 1.67 0.81 0.84 0.13 4.35 13.25 6.26 0.46 2.00 1.18 0.95 0.15 6.60 17.60
S30TS007 4.43 0.39 1.98 0.96 0.73 0.11 3.85 12.45 5.54 0.40 2.37 1.39 0.82 0.13 5.84 16.49
S30TS008 7.65 0.66 2.59 1.26 0.95 0.15 6.62 19.88 9.56 0.68 3.11 1.83 1.07 0.16 10.04 26.45
S30TS009 11.91 2.23 18.53 12.02 0.00 0.00 14.61 59.30 19.85 2.30 22.23 16.08 0.00 0.00 30.44 90.90
S30TS010 17.66 3.31 24.70 16.02 0.00 0.00 21.66 83.35 29.43 3.42 29.64 21.44 0.00 0.00 45.13 129.06
S30TS011 29.30 5.50 49.40 32.04 0.00 0.00 35.94 152.18 48.83 5.67 59.28 42.89 0.00 0.00 74.87 231.54
2-299
2 247
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

S35
S35AR001 0.53 0.04 0.00 0.00 0.00 0.00 0.58 1.15
S35AR002 0.75 0.06 0.00 0.00 0.00 0.00 0.83 1.64
S40
S40BO002 28.74 2.83 42.72 5.18 1.88 0.29 35.62 117.26 35.92 2.90 55.28 6.70 7.75 1.19 49.76 159.50
S40BO003 27.07 2.67 42.72 5.18 1.88 0.29 33.56 113.37 33.84 2.73 55.28 6.70 7.75 1.19 46.88 154.37
S40BO004 27.55 2.72 42.72 5.18 1.88 0.29 34.15 114.49 34.44 2.78 55.28 6.70 7.75 1.19 47.71 155.85
S40CA001 31.91 3.14 36.67 4.44 2.53 0.39 39.54 118.62 39.88 3.22 47.45 5.75 9.75 1.49 55.23 162.77
S40CA002 30.51 3.02 36.67 4.44 1.80 0.28 37.83 114.55 38.14 3.09 47.45 5.75 6.84 1.05 52.85 155.17
S40CA003 24.62 2.61 41.53 5.03 11.31 1.73 30.98 117.81 30.77 2.67 53.75 6.51 45.15 6.91 43.28 189.04
S40CA004 40.12 4.09 64.08 7.77 9.71 1.49 50.07 177.33 50.15 4.19 82.92 10.05 37.46 5.73 69.94 260.44
S45
S45DA004 1.81 0.11 0.00 0.25 0.00 0.00 2.50 4.67
S45DA005 2.16 0.13 0.00 0.25 0.00 0.00 2.98 5.52
S45DA007 2.28 0.14 0.00 0.25 0.00 0.00 3.14 5.81
T10
T10CA001 1.16 0.11 0.00 0.08 0.00 0.00 1.31 2.66 1.45 0.11 0.00 0.08 0.00 0.00 1.84 3.48
T10CA002 1.44 0.14 0.00 0.08 0.00 0.00 1.62 3.28 1.80 0.14 0.00 0.08 0.00 0.00 2.27 4.29
T10CA004 1.29 0.12 0.00 0.08 0.00 0.00 1.45 2.94 1.61 0.13 0.00 0.08 0.00 0.00 2.03 3.85
T10CA005 1.44 0.14 0.00 0.08 0.00 0.00 1.62 3.28 1.80 0.14 0.00 0.08 0.00 0.00 2.27 4.29
T10CA007 1.96 0.19 0.00 0.08 0.00 0.00 2.20 4.43 2.45 0.19 0.00 0.08 0.00 0.00 3.09 5.81
T10CA008 2.19 0.21 0.00 0.08 0.00 0.00 2.46 4.94 2.74 0.22 0.00 0.08 0.00 0.00 3.46 6.50
T10CA009 2.37 0.23 0.00 0.08 0.00 0.00 2.66 5.34 2.96 0.23 0.00 0.08 0.00 0.00 3.74 7.01
T10CA010 2.59 0.25 0.00 0.08 0.00 0.00 2.91 5.83 3.24 0.26 0.00 0.08 0.00 0.00 4.09 7.67
T10CA011 3.65 0.35 0.00 0.08 0.00 0.00 4.10 8.18 4.57 0.36 0.00 0.08 0.00 0.00 5.77 10.78
2-300
2 248
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

T10 cont.
T10CA012 3.50 0.34 0.00 0.08 0.00 0.00 3.93 7.85 4.37 0.34 0.00 0.08 0.00 0.00 5.52 10.31
T10CA013 3.84 0.37 0.00 0.08 0.00 0.00 4.31 8.60 4.80 0.38 0.00 0.08 0.00 0.00 6.06 11.32
T10CA014 3.19 0.31 0.00 0.08 0.00 0.00 3.58 7.16 3.99 0.31 0.00 0.08 0.00 0.00 5.03 9.41
T10CA015 4.80 0.46 0.00 0.10 0.00 0.00 5.38 10.74 6.00 0.47 0.00 0.10 0.00 0.00 7.57 14.14
T10CA016 4.66 0.45 0.00 0.12 0.00 0.00 5.23 10.46 5.82 0.46 0.00 0.12 0.00 0.00 7.35 13.75
T10CA017 5.05 0.49 0.00 0.13 0.00 0.00 5.67 11.34 6.31 0.50 0.00 0.13 0.00 0.00 7.97 14.91
T10CA018 4.46 0.43 0.00 0.13 0.00 0.00 5.00 10.02 5.57 0.44 0.00 0.13 0.00 0.00 7.03 13.17
T10CA019 0.13 0.01 0.00 0.05 0.00 0.00 0.14 0.33 0.16 0.01 0.00 0.05 0.00 0.00 0.20 0.42
T10CA020 4.78 0.46 0.00 0.15 0.00 0.00 5.36 10.75 5.97 0.47 0.00 0.15 0.00 0.00 7.54 14.13
T10CA021 6.33 0.61 0.00 0.19 0.00 0.00 7.10 14.23 7.91 0.62 0.00 0.19 0.00 0.00 9.98 18.70
T10CA022 6.16 0.59 0.00 0.19 0.00 0.00 6.92 13.86 7.70 0.61 0.00 0.19 0.00 0.00 9.73 18.23
T10CA023 6.41 0.62 0.00 0.20 0.00 0.00 7.20 14.43 8.02 0.63 0.00 0.20 0.00 0.00 10.12 18.97
T10CA024 4.84 0.47 0.00 0.28 0.00 0.00 5.44 11.03 6.06 0.48 0.00 0.28 0.00 0.00 7.65 14.47
T10CA025 5.86 0.56 0.00 0.29 0.00 0.00 6.57 13.28 7.32 0.58 0.00 0.29 0.00 0.00 9.24 17.43
T10CA026 9.21 0.89 0.00 0.40 0.00 0.00 10.34 20.84 11.51 0.91 0.00 0.40 0.00 0.00 14.53 27.35
T10CA027 12.20 1.18 0.00 0.42 0.00 0.00 13.70 27.50 15.25 1.20 0.00 0.42 0.00 0.00 19.26 36.13
T10JD001 0.95 0.10 0.00 0.25 0.10 0.02 1.08 2.50 1.19 0.10 0.00 0.25 0.12 0.02 1.52 3.20
T15
T15CA002 8.07 0.95 8.31 1.30 0.00 0.00 14.22 32.85 10.08 0.96 10.75 1.68 0.00 0.00 20.21 43.68
T15CA005 9.06 1.06 9.49 1.48 0.00 0.00 15.97 37.06 11.32 1.08 12.28 1.92 0.00 0.00 22.70 49.30
T15CA008 18.36 2.16 17.21 2.69 0.00 0.00 32.36 72.78 22.94 2.19 22.27 3.48 0.00 0.00 45.99 96.87
T15CA009 27.64 3.25 19.58 3.06 0.00 0.00 48.73 102.26 34.55 3.30 25.34 3.95 0.00 0.00 69.25 136.39
T15CA011 27.19 3.19 21.95 3.43 0.00 0.00 47.94 103.70 33.99 3.25 28.41 4.43 0.00 0.00 68.13 138.21
T15CA012 21.72 2.84 28.48 3.46 0.00 0.00 38.98 95.48 25.86 2.87 36.85 4.47 0.00 0.00 48.37 118.42
T15CA014 24.62 3.22 28.48 3.46 0.00 0.00 44.19 103.97 29.31 3.26 36.85 4.47 0.00 0.00 54.83 128.72
T15CA016 37.49 4.90 36.78 4.46 0.00 0.00 67.29 150.92 44.63 4.96 47.60 5.78 0.00 0.00 83.49 186.46
T15CA017 43.54 5.69 48.65 5.91 0.00 0.00 78.14 181.93 51.83 5.76 62.96 7.64 0.00 0.00 96.96 225.15
2-301
2 249
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

T15 cont.
T15CA018 64.30 9.03 58.70 3.95 0.00 0.00 108.18 244.16 77.16 9.13 74.90 5.04 0.00 0.00 146.12 312.35
T15CA019 104.39 14.66 86.03 5.79 0.00 0.00 175.63 386.50 125.27 14.82 109.76 7.39 0.00 0.00 237.22 494.46
T15CA020 8.58 1.01 9.49 1.48 0.00 0.00 15.13 35.69 10.73 1.03 12.28 1.92 0.00 0.00 21.51 47.47
T15CA021 9.72 1.14 10.68 1.67 0.00 0.00 17.13 40.34 12.15 1.16 13.82 2.16 0.00 0.00 24.35 53.64
T15CA022 9.65 1.13 10.68 1.67 0.00 0.00 17.00 40.13 12.06 1.15 13.82 2.16 0.00 0.00 24.17 53.36
T15CA023 22.50 2.64 19.58 3.06 0.00 0.00 39.66 87.44 28.12 2.69 25.34 3.95 0.00 0.00 56.37 116.47
T15CA024 9.21 1.08 13.05 2.04 0.00 0.00 16.24 41.62 11.52 1.10 16.89 2.64 0.00 0.00 23.08 55.23
T15CS004 7.99 0.94 7.95 1.24 0.00 0.00 14.09 32.21 9.99 0.95 10.29 1.61 0.00 0.00 20.03 42.87
T15CS007 13.96 1.64 14.12 2.20 0.00 0.00 24.61 56.53 17.45 1.67 18.27 2.85 0.00 0.00 34.97 75.21
T15JD005 6.69 0.79 8.31 1.30 0.00 0.00 11.80 28.89 8.37 0.80 10.75 1.68 0.00 0.00 16.77 38.37
T15JD006 6.83 0.80 8.31 1.30 0.00 0.00 12.04 29.28 8.54 0.82 10.75 1.68 0.00 0.00 17.11 38.90
T15JD007 10.47 1.23 11.98 1.87 0.00 0.00 18.46 44.01 13.09 1.25 15.51 2.42 0.00 0.00 26.24 58.51
T15JD008 17.01 2.00 18.39 2.87 0.00 0.00 29.99 70.26 21.27 2.03 23.80 3.71 0.00 0.00 42.63 93.44
T15JD009 17.72 2.08 19.58 3.06 0.00 0.00 31.23 73.67 22.15 2.12 25.34 3.95 0.00 0.00 44.39 97.95
T15JD010 24.04 2.82 22.19 3.46 0.00 0.00 42.37 94.88 30.05 2.87 28.72 4.48 0.00 0.00 60.22 126.34
T15JD011 25.64 3.01 24.33 3.80 0.00 0.00 45.21 101.99 32.05 3.06 31.48 4.91 0.00 0.00 64.25 135.75
T15KM008 34.61 4.52 36.78 4.46 0.00 0.00 62.12 142.49 41.20 4.58 47.60 5.78 0.00 0.00 77.08 176.24
T20
T20CA001 30.30 3.76 24.29 2.95 7.00 1.07 23.38 92.75 32.63 3.78 30.99 3.76 29.40 4.50 27.30 132.36
T20CA002 44.23 5.59 34.31 4.16 14.94 2.29 34.21 139.73 47.63 5.61 43.78 5.31 62.74 9.60 39.95 214.62
T20CA003 67.12 8.61 48.68 5.91 18.60 2.85 52.05 203.82 72.29 8.65 62.11 7.54 78.12 11.95 60.78 301.44
T25
T25CA006 19.58 1.72 28.89 3.51 0.00 0.00 21.28 74.98
T25CA007 21.49 1.89 31.59 3.83 0.00 0.00 23.37 82.17
T25CA008 23.30 2.05 38.19 4.64 0.00 0.00 25.32 93.50
T25JD021 9.66 0.73 12.44 1.51 0.80 0.12 8.71 33.97
2-302
2 250
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

T25 cont.
T25JD022 14.01 1.04 18.39 2.23 0.80 0.12 12.61 49.20
T25JD023 19.45 1.47 25.42 3.09 1.74 0.27 17.54 68.98
T25JD024 22.59 1.70 30.83 3.74 1.74 0.27 20.35 81.22
T25JD025 23.37 1.92 38.95 4.73 5.44 0.83 21.36 96.60
T25JD026 28.67 2.30 49.77 6.04 5.44 0.83 26.11 119.16
T25JD027 1.37 0.12 4.87 0.59 0.45 0.07 1.26 8.73
T25JD028 1.50 0.13 5.95 0.72 0.45 0.07 1.38 10.20
T25JD029 2.13 0.17 5.95 0.72 0.45 0.07 1.94 11.43
T25JD030 3.37 0.26 7.03 0.85 0.45 0.07 3.05 15.08
T25JD031 3.41 0.27 8.98 1.09 0.54 0.08 3.09 17.46
T25JD032 3.47 0.32 10.93 1.33 1.82 0.28 3.24 21.39
T30
T30DW005 3.69 0.31 4.54 0.55 0.33 0.05 4.54 14.01 4.92 0.32 6.01 0.73 1.22 0.19 6.73 20.12
T30DW010 10.52 0.90 10.71 1.30 2.34 0.36 13.03 39.16 14.03 0.93 14.17 1.72 8.72 1.33 19.30 60.20
T30DW011 54.22 4.28 23.80 2.88 0.00 0.00 66.01 151.19 72.29 4.43 31.48 3.82 0.00 0.00 97.77 209.79
T30DW012 0.96 0.08 3.55 0.43 0.03 0.00 1.17 6.22 1.28 0.08 4.63 0.56 0.09 0.01 1.73 8.38
T30DW013 1.20 0.10 4.88 0.59 0.13 0.02 1.48 8.40 1.60 0.10 6.37 0.77 0.48 0.07 2.19 11.58
T30DW014 12.72 1.03 11.04 1.34 0.57 0.09 15.57 42.36 16.96 1.07 14.60 1.77 2.13 0.33 23.06 59.92
T30DW015 3.79 0.33 4.54 0.55 0.57 0.09 4.69 14.56 5.05 0.34 6.01 0.73 2.13 0.33 6.95 21.54
T30DW016 6.81 0.55 6.49 0.79 0.33 0.05 8.34 23.36 9.08 0.57 8.59 1.04 1.22 0.19 12.35 33.04
T30DW017 8.06 0.66 8.44 1.02 0.57 0.09 9.89 28.73 10.74 0.69 11.16 1.35 2.13 0.33 14.65 41.05
T30DW018 10.94 0.89 10.71 1.30 0.57 0.09 13.40 37.90 14.58 0.92 14.17 1.72 2.13 0.33 19.85 53.70
T30TM007 50.25 3.97 23.80 2.88 0.00 0.00 61.18 142.08 67.01 4.11 31.48 3.82 0.00 0.00 90.63 197.05
T30TM008 50.58 3.99 23.80 2.88 0.00 0.00 61.58 142.83 67.44 4.13 31.48 3.82 0.00 0.00 91.21 198.08
T30TM012 86.57 6.83 41.65 5.05 0.00 0.00 105.40 245.50 115.43 7.07 55.09 6.69 0.00 0.00 156.12 340.40
T30TM013 141.87 11.19 56.80 6.88 0.00 0.00 172.73 389.47 189.16 11.59 75.12 9.12 0.00 0.00 255.84 540.83
T30TM014 135.83 10.72 56.80 6.88 0.00 0.00 165.37 375.60 181.10 11.10 75.12 9.12 0.00 0.00 244.94 521.38
2-303
2 251
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

T30 cont.
T30TM015 144.84 11.43 56.80 6.88 0.00 0.00 176.35 396.30 193.12 11.84 75.12 9.12 0.00 0.00 261.20 550.40
T30VE007 19.82 1.56 13.52 1.64 0.00 0.00 24.13 60.67 26.43 1.62 17.89 2.17 0.00 0.00 35.75 83.86
T30VE008 25.19 1.99 20.02 2.43 0.00 0.00 30.67 80.30 33.59 2.06 26.47 3.21 0.00 0.00 45.43 110.76
T30VE009 40.86 3.22 27.05 3.28 0.00 0.00 49.75 124.16 54.49 3.34 35.77 4.34 0.00 0.00 73.69 171.63
T30VE010 49.73 3.92 29.75 3.61 0.00 0.00 60.54 147.55 66.30 4.06 39.35 4.78 0.00 0.00 89.68 204.17
T35
T35CT001 26.37 2.08 15.15 1.84 0.00 0.00 32.11 77.55 35.16 2.16 20.03 2.43 0.00 0.00 47.56 107.34
T35CT002 32.47 2.56 15.15 1.84 0.00 0.00 39.53 91.55 43.29 2.65 20.03 2.43 0.00 0.00 58.55 126.95
T35CT003 36.48 2.88 20.02 2.43 0.00 0.00 44.42 106.23 48.65 2.98 26.47 3.21 0.00 0.00 65.79 147.10
T35CT004 34.34 2.71 11.04 1.34 0.00 0.00 41.80 91.23 45.78 2.81 14.60 1.77 0.00 0.00 61.92 126.88
T35CT005 32.48 2.56 11.04 1.34 0.00 0.00 39.55 86.97 43.31 2.65 14.60 1.77 0.00 0.00 58.58 120.91
T35CT006 32.48 2.56 11.04 1.34 0.00 0.00 39.55 86.97 43.31 2.65 14.60 1.77 0.00 0.00 58.58 120.91
T35CT007 35.96 2.84 11.04 1.34 0.00 0.00 43.78 94.96 47.94 2.94 14.60 1.77 0.00 0.00 64.84 132.09
T35CT008 46.12 3.64 16.23 1.97 0.00 0.00 56.15 124.11 61.49 3.77 21.46 2.60 0.00 0.00 83.17 172.49
T35CT009 53.70 4.24 16.23 1.97 0.00 0.00 65.38 141.52 71.60 4.39 21.46 2.60 0.00 0.00 96.84 196.89
T35CT010 52.60 4.15 16.23 1.97 0.00 0.00 64.04 138.99 70.14 4.30 21.46 2.60 0.00 0.00 94.86 193.36
T35CT011 63.30 4.99 18.93 2.29 0.00 0.00 77.06 166.57 84.40 5.17 25.04 3.03 0.00 0.00 114.15 231.79
T40
T40AG001 8.88 0.73 8.66 1.20 0.48 0.07 8.64 28.66
T40AH001 2.95 0.23 0.00 0.25 0.00 0.00 3.25 6.68
T40AH003 4.37 0.34 0.00 0.25 0.00 0.00 4.82 9.78
T40AH004 5.40 0.43 0.00 0.25 0.00 0.00 5.96 12.04
T40GN001 1.88 0.12 0.00 0.00 0.00 0.00 1.62 3.62 2.32 0.13 0.00 0.00 0.00 0.00 2.28 4.73
T40KF011 0.47 0.04 0.00 0.00 0.00 0.00 0.39 0.90
T40KF013 0.51 0.04 0.00 0.00 0.00 0.00 0.42 0.97
T40KF014 0.55 0.04 0.00 0.00 0.00 0.00 0.45 1.04
2-304
2 252
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

T40 cont.
T40KF016 0.66 0.05 0.00 0.00 0.00 0.00 0.55 1.26
T40KF018 0.79 0.06 0.00 0.00 0.00 0.00 0.65 1.50
T40KF020 0.95 0.07 0.00 0.00 0.00 0.00 0.79 1.81
T40KF021 0.47 0.04 0.00 0.10 0.00 0.00 0.46 1.07
T40KF022 0.85 0.07 0.00 0.10 0.00 0.00 0.82 1.84
T40KF023 0.34 0.03 0.00 0.05 0.00 0.00 0.33 0.75
T40KF024 0.50 0.04 0.00 0.05 0.00 0.00 0.48 1.07
T40MY002 0.62 0.04 0.00 0.00 0.00 0.00 0.53 1.19 0.76 0.04 0.00 0.00 0.00 0.00 0.75 1.55
T40MY003 0.77 0.05 0.00 0.00 0.00 0.00 0.66 1.48 0.95 0.05 0.00 0.00 0.00 0.00 0.93 1.93
T40MY004 0.89 0.06 0.00 0.00 0.00 0.00 0.77 1.72 1.10 0.06 0.00 0.00 0.00 0.00 1.08 2.24
T40MY005 1.26 0.08 0.00 0.00 0.00 0.00 1.09 2.43 1.56 0.09 0.00 0.00 0.00 0.00 1.53 3.18
T40MY006 1.44 0.09 0.00 0.00 0.00 0.00 1.24 2.77 1.77 0.10 0.00 0.00 0.00 0.00 1.74 3.61
T40PA001 0.77 0.06 0.00 0.24 0.00 0.00 0.85 1.92
T40PA002 4.03 0.32 0.00 0.24 0.00 0.00 4.45 9.04
T40PA004 5.20 0.41 0.00 0.26 0.00 0.00 5.74 11.61
T40PA005 9.82 0.77 0.00 0.27 0.00 0.00 10.83 21.69
T40PA006 11.35 0.90 0.00 0.27 0.00 0.00 12.53 25.05
T40PA007 5.10 0.40 0.00 0.26 0.00 0.00 5.62 11.38
T40RS001 2.96 0.26 0.00 0.00 0.00 0.00 2.61 5.83
T40RS002 3.05 0.26 0.00 0.00 0.00 0.00 2.70 6.01
T40RS003 3.28 0.28 0.00 0.00 0.00 0.00 2.89 6.45
T40XX034 16.97 1.22 29.50 4.08 0.00 0.00 15.43 67.20
T40XX035 17.24 1.24 31.39 4.34 0.00 0.00 15.68 69.89
T40XX036 18.09 1.30 35.78 4.95 0.00 0.00 16.45 76.57
T40XX037 20.33 1.46 35.78 4.95 0.00 0.00 18.48 81.00
T40XX038 21.27 1.53 35.78 4.95 0.00 0.00 19.35 82.88
2-305
2 253
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

T45
T45EA006 3.50 0.35 0.00 0.50 1.93 0.30 2.20 8.78
T45EA007 4.62 0.47 0.00 0.50 2.90 0.44 2.91 11.84
T45G1001 8.33 0.88 8.11 0.84 0.00 0.00 8.59 26.75
T45G1002 4.15 0.44 8.11 0.84 0.00 0.00 4.28 17.82
T45MY004 2.31 0.24 0.00 0.30 1.56 0.24 2.04 6.69 2.88 0.24 0.00 0.30 5.70 0.87 2.91 12.90
T45MY005 3.06 0.32 0.00 0.30 2.34 0.36 2.71 9.09 3.82 0.33 0.00 0.30 8.55 1.31 3.87 18.18
T45MY006 3.17 0.33 0.00 0.30 2.34 0.36 2.80 9.30 3.96 0.34 0.00 0.30 8.55 1.31 4.01 18.47
T45MY007 3.03 0.32 0.00 0.30 2.34 0.36 2.69 9.04 3.79 0.33 0.00 0.30 8.55 1.31 3.84 18.12
T45MY015 2.54 0.26 0.00 0.40 1.56 0.24 2.08 7.08 3.18 0.26 0.00 0.40 5.70 0.87 3.00 13.41
T45MY016 2.60 0.26 0.00 0.40 1.56 0.24 2.12 7.18 3.25 0.27 0.00 0.40 5.70 0.87 3.06 13.55
T45MY017 2.60 0.29 0.00 0.40 2.34 0.36 2.15 8.14 3.25 0.30 0.00 0.40 8.55 1.31 3.11 16.92
T45MY018 1.87 0.18 0.00 0.40 1.56 0.24 1.43 5.68
T45MY019 1.84 0.18 0.00 0.40 1.56 0.24 1.42 5.64
T45XX001 3.31 0.30 0.00 0.40 1.11 0.17 2.88 8.17 4.13 0.31 0.00 0.40 4.04 0.62 4.11 13.61
T45XX003 4.08 0.36 0.00 0.40 1.11 0.17 3.54 9.66 5.10 0.37 0.00 0.40 4.04 0.62 5.06 15.59
T45XX008 2.64 0.25 0.00 0.40 1.11 0.17 2.14 6.71 3.30 0.26 0.00 0.40 4.04 0.62 3.09 11.71
T45XX009 2.97 0.23 0.00 0.40 1.11 0.17 2.22 7.10
T45XX010 3.35 0.26 0.00 0.40 1.11 0.17 2.50 7.79
T45XX011 2.73 0.25 0.00 0.40 0.98 0.15 1.70 6.21
T45XX012 2.91 0.27 0.00 0.40 0.98 0.15 1.81 6.52
T45XX013 3.03 0.28 0.00 0.40 1.11 0.17 1.89 6.88
T45XX014 3.65 0.34 0.00 0.50 1.47 0.22 2.28 8.46
T45XX015 15.67 1.31 0.00 0.50 1.47 0.22 9.65 28.82
T45XX016 8.33 0.72 0.00 0.50 1.66 0.25 5.15 16.61
T45XX017 12.00 1.03 0.00 0.50 1.93 0.30 7.41 23.17
T45XX018 13.18 1.12 0.00 0.50 1.93 0.30 8.13 25.16
T45XX019 5.16 0.48 0.00 0.50 1.93 0.30 3.22 11.59
2-306
2 254
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

T45 cont.
T45XX020 4.87 0.47 0.00 0.60 2.21 0.34 3.04 11.53
T45XX021 5.37 0.51 0.00 0.60 2.21 0.34 3.35 12.38
T45XX022 6.06 0.57 0.00 0.60 2.57 0.39 3.78 13.97
T45XX023 7.23 0.69 0.00 0.60 3.13 0.48 4.52 16.65
T45XX024 2.30 0.22 0.00 0.09 1.11 0.17 1.44 5.33
T45XX025 2.50 0.24 0.00 0.10 1.11 0.17 1.56 5.68
T45XX026 1.45 0.13 0.00 0.40 0.55 0.08 0.90 3.51
T45XX027 1.60 0.15 0.00 0.40 0.72 0.11 1.00 3.98
T45XX028 1.75 0.18 0.00 0.40 1.04 0.16 1.10 4.63
T45XX029 6.29 0.69 6.82 0.71 0.55 0.08 5.60 20.74
T45XX030 6.00 0.69 6.82 0.71 1.11 0.17 5.40 20.90
T45XX031 7.42 0.84 6.82 0.71 1.11 0.17 6.65 23.72
T45XX032 4.35 0.32 0.00 0.50 0.83 0.13 3.23 9.36
T45XX033 5.32 0.39 0.00 0.60 1.11 0.17 3.96 11.55
T45XX034 2.45 0.23 0.00 0.40 1.11 0.17 1.53 5.89
T45XX035 2.63 0.25 0.00 0.40 1.11 0.17 1.64 6.20
T50
T50GM001 1.72 0.14 6.32 0.77 0.27 0.04 1.72 10.98 2.12 0.15 8.12 0.98 0.90 0.14 2.26 14.67
T50GM004 3.97 0.32 15.00 1.82 0.27 0.04 3.94 25.36 4.89 0.33 19.29 2.34 0.90 0.14 5.19 33.08
T50GM005 4.28 0.35 15.00 1.82 0.29 0.04 4.24 26.02 5.27 0.36 19.29 2.34 1.01 0.15 5.59 34.01
T50XX001 1.62 0.14 6.84 0.83 0.34 0.05 1.63 11.45 2.00 0.14 8.80 1.07 1.12 0.17 2.15 15.45
T50XX002 2.01 0.17 6.84 0.83 0.25 0.04 2.01 12.15 2.48 0.17 8.80 1.07 0.83 0.13 2.64 16.12
T50XX003 2.29 0.19 9.48 1.15 0.29 0.04 2.28 15.72 2.82 0.20 12.18 1.48 0.94 0.14 3.01 20.77
T50XX004 1.98 0.17 6.84 0.83 0.36 0.06 1.98 12.22 2.44 0.17 8.80 1.07 1.25 0.19 2.62 16.54
T50XX005 2.40 0.20 6.84 0.83 0.26 0.04 2.38 12.95 2.95 0.20 8.80 1.07 0.92 0.14 3.14 17.22
T50XX006 2.47 0.20 9.48 1.15 0.30 0.05 2.46 16.11 3.04 0.21 12.18 1.48 1.04 0.16 3.24 21.35
T50XX007 1.72 0.15 6.84 0.83 0.34 0.05 1.73 11.66 2.12 0.15 8.80 1.07 1.12 0.17 2.27 15.70
2-307
2 255
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

T50 cont.
T50XX008 2.14 0.18 6.84 0.83 0.25 0.04 2.13 12.41 2.64 0.18 8.80 1.07 0.83 0.13 2.81 16.46
T50XX009 2.65 0.22 9.48 1.15 0.29 0.04 2.63 16.46 3.26 0.22 12.18 1.48 0.94 0.14 3.47 21.69
T50XX010 2.39 0.20 6.84 0.83 0.36 0.06 2.38 13.06 2.94 0.20 8.80 1.07 1.25 0.19 3.14 17.59
T50XX011 2.61 0.21 9.48 1.15 0.26 0.04 2.59 16.34 3.21 0.22 12.18 1.48 0.92 0.14 3.42 21.57
T50XX012 2.73 0.22 9.48 1.15 0.30 0.05 2.71 16.64 3.36 0.23 12.18 1.48 1.04 0.16 3.57 22.02
T50XX013 2.15 0.18 2.13 0.22 0.34 0.05 2.15 7.22 2.65 0.19 3.04 0.32 1.12 0.17 2.83 10.32
T50XX014 2.44 0.20 2.13 0.22 0.25 0.04 2.43 7.71 3.01 0.21 3.04 0.32 0.83 0.13 3.20 10.74
T50XX015 2.82 0.23 3.69 0.38 0.29 0.04 2.80 10.25 3.47 0.24 5.27 0.55 0.94 0.14 3.69 14.30
T50XX016 2.59 0.22 3.69 0.38 0.36 0.06 2.58 9.88 3.19 0.22 5.27 0.55 1.25 0.19 3.41 14.08
T50XX017 2.66 0.22 3.69 0.38 0.26 0.04 2.64 9.89 3.27 0.22 5.27 0.55 0.92 0.14 3.48 13.85
T50XX018 3.19 0.26 3.69 0.38 0.30 0.05 3.16 11.03 3.92 0.27 5.27 0.55 1.04 0.16 4.17 15.38
T50XX019 2.53 0.21 3.69 0.38 0.25 0.04 2.52 9.62 3.12 0.21 5.27 0.55 0.83 0.13 3.32 13.43
T50XX020 3.09 0.25 3.69 0.38 0.26 0.04 3.06 10.77 3.80 0.26 5.27 0.55 0.92 0.14 4.04 14.98
T50XX021 2.78 0.23 3.69 0.38 0.29 0.04 2.76 10.17 3.42 0.23 5.27 0.55 0.94 0.14 3.64 14.19
T50XX022 4.42 0.45 12.39 1.40 0.52 0.08 4.08 23.34 5.53 0.46 16.04 1.81 2.02 0.31 5.50 31.67
T50XX023 3.44 0.35 25.27 3.28 0.52 0.08 3.18 36.12 4.30 0.36 32.37 4.20 2.02 0.31 4.29 47.85
T50XX024 2.96 0.31 25.27 3.28 0.52 0.08 2.74 35.16 3.70 0.31 32.37 4.20 2.02 0.31 3.70 46.61
T50XX025 5.78 0.59 11.70 1.32 0.84 0.13 5.34 25.70 7.23 0.60 15.15 1.71 3.48 0.53 7.20 35.90
T50XX026 5.88 0.60 14.46 1.63 0.81 0.12 5.43 28.93 7.35 0.61 18.71 2.11 3.13 0.48 7.32 39.71
T50XX027 7.95 0.94 25.76 3.12 0.75 0.11 7.32 45.95 9.55 0.95 33.27 4.03 2.86 0.44 10.14 61.24
T50XX028 7.83 0.94 22.36 2.71 1.14 0.17 7.23 42.38 9.40 0.95 28.88 3.50 4.41 0.67 10.02 57.83
T50XX029 7.18 0.86 30.13 3.65 1.14 0.17 6.64 49.77 8.62 0.88 38.92 4.72 4.41 0.67 9.20 67.42
T50XX030 9.26 1.10 34.02 4.12 1.14 0.17 8.54 58.35 11.12 1.12 43.94 5.32 4.41 0.67 11.83 78.41
T50XX031 8.48 1.01 38.88 4.71 1.17 0.18 7.82 62.25 10.17 1.03 50.22 6.09 4.53 0.69 10.84 83.57
T50XX032 8.65 1.02 25.76 3.12 0.75 0.11 7.95 47.36 10.38 1.03 33.27 4.03 2.86 0.44 11.02 63.03
T50XX033 9.27 1.10 38.88 4.71 1.17 0.18 8.54 63.85 11.12 1.12 50.22 6.09 4.53 0.69 11.84 85.61
T50XX035 8.29 0.83 14.46 1.63 0.81 0.12 7.64 33.78 10.37 0.85 18.71 2.11 3.13 0.48 10.29 45.94
2-308
2 256
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

T55
T55CA002 35.14 6.35 38.56 5.66 12.67 1.94 40.21 140.53 39.05 6.38 49.91 7.33 49.81 7.62 47.19 207.29
T55CA003 48.77 9.21 55.65 8.17 28.43 4.35 56.21 210.79 54.19 9.26 72.02 10.58 111.85 17.11 65.97 340.98
T55CA007 27.00 4.81 28.89 4.24 14.33 2.19 30.83 112.29 30.00 4.84 37.39 5.49 56.38 8.63 36.18 178.91
T55CA014 25.08 2.80 17.92 1.46 0.00 0.00 25.19 72.45 26.61 2.81 21.66 1.77 0.00 0.00 28.43 81.28
T55CA015 28.69 3.20 23.87 1.95 0.00 0.00 28.82 86.53 30.44 3.22 28.84 2.35 0.00 0.00 32.52 97.37
T55CA016 34.72 3.87 21.78 1.78 0.00 0.00 34.88 97.03 36.84 3.89 26.31 2.15 0.00 0.00 39.36 108.55
T55CA017 39.22 4.37 29.73 2.43 0.00 0.00 39.40 115.15 41.62 4.39 35.93 2.93 0.00 0.00 44.46 129.33
T55CA018 40.28 4.49 33.92 2.77 0.00 0.00 40.47 121.93 42.75 4.51 40.99 3.34 0.00 0.00 45.66 137.25
T55JD001 23.58 2.79 22.20 1.81 7.52 1.15 23.90 82.95 25.02 2.80 26.82 2.19 29.57 4.52 26.97 117.89
T55JD002 26.35 3.10 23.87 1.95 7.52 1.15 26.69 90.63 27.96 3.11 28.84 2.35 29.57 4.52 30.12 126.47
T55JD003 33.24 4.15 31.83 2.60 20.57 3.15 33.99 129.53 35.28 4.17 38.46 3.14 80.89 12.38 38.35 212.67
T55JD004 37.38 4.50 34.59 2.82 15.45 2.36 38.00 135.10 39.67 4.52 41.80 3.41 60.79 9.30 42.88 202.37
T55KM009 19.43 3.55 28.95 4.25 14.33 2.19 22.27 94.97 21.59 3.56 37.47 5.50 56.38 8.63 26.13 159.26
T55KM012 37.34 7.30 61.82 9.08 28.43 4.35 43.29 191.61 41.49 7.33 80.00 11.75 111.85 17.11 50.80 320.33
T55KM013 95.81 16.88 88.16 12.95 23.20 3.55 109.19 349.74 106.46 16.96 114.10 16.76 91.23 13.96 128.15 487.62
T55KM014 112.29 19.94 118.66 17.43 31.52 4.82 128.14 432.80 124.77 20.04 153.56 22.55 123.97 18.97 150.38 614.24
T55KM015 21.89 2.88 32.58 2.66 20.57 3.15 22.59 106.32 23.23 2.89 39.37 3.21 80.89 12.38 25.49 187.46
T55KM016 29.74 3.65 36.02 2.94 15.45 2.36 30.33 120.49 31.56 3.66 43.52 3.55 60.79 9.30 34.22 186.60
T55VO002 23.45 2.84 25.04 2.04 10.76 1.65 23.87 89.65 24.89 2.86 30.26 2.47 42.70 6.53 26.93 136.64
T55VO003 25.43 3.00 25.04 2.04 7.52 1.15 25.77 89.95 26.99 3.01 30.26 2.47 29.57 4.52 29.08 125.90
T55VO004 36.71 4.37 34.68 2.83 12.74 1.95 37.25 130.53 38.95 4.39 41.90 3.42 50.10 7.67 42.03 188.46
T55VO005 30.45 3.53 28.14 2.30 5.48 0.84 30.77 101.51 32.31 3.55 34.01 2.78 21.55 3.30 34.72 132.22
T55VO006 38.80 4.85 38.86 3.17 24.33 3.72 39.68 153.41 41.17 4.87 46.96 3.83 95.68 14.64 44.78 251.93
T56
T56CA006 54.96 10.24 62.20 9.14 31.22 4.78 63.21 235.75 61.07 10.29 101.48 14.04 121.90 18.65 74.18 401.61
2-309
2 257
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

T57
T57CU001 9.99 0.97 8.22 1.00 0.44 0.07 11.04 31.73
T57CU002 12.29 1.19 8.22 1.00 0.44 0.07 13.58 36.79
T57CU003 10.50 1.02 32.46 3.93 0.44 0.07 11.61 60.03
T57CU004 11.62 1.13 37.87 4.59 0.44 0.07 12.84 68.56
T57CU005 13.72 1.33 45.98 5.57 0.44 0.07 15.16 82.27
T60
T60KI001 30.13 3.54 35.70 4.94 3.93 0.60 28.35 107.19 36.15 3.60 47.22 6.53 15.03 2.30 38.83 149.66
T60KI002 19.66 2.57 35.70 4.94 13.20 2.02 18.93 97.02 23.59 2.61 47.22 6.53 50.95 7.80 25.93 164.63
T60KI003 27.44 3.61 49.98 6.91 19.11 2.92 26.45 136.42 32.93 3.67 66.11 9.14 73.75 11.28 36.23 233.11
T60KI004 40.71 5.12 49.98 6.91 19.11 2.92 38.86 163.61 48.85 5.20 66.11 9.14 73.75 11.28 53.23 267.56
T60KI006 61.80 7.53 61.02 8.44 19.20 2.94 58.58 219.51 74.17 7.64 80.70 11.16 74.07 11.33 80.26 339.33
T60SO001 31.12 3.88 35.70 4.94 13.20 2.02 29.65 120.51 37.34 3.94 47.22 6.53 50.95 7.80 40.62 194.40
T60SO002 44.04 5.40 48.69 6.73 15.22 2.33 41.81 164.22 52.85 5.49 64.39 8.91 58.74 8.99 57.29 256.66
T60SO003 44.78 5.49 48.69 6.73 15.22 2.33 42.50 165.74 53.74 5.57 64.39 8.91 58.74 8.99 58.23 258.57
T60SO004 54.91 6.82 59.50 8.23 22.31 3.41 52.26 207.44 65.89 6.93 78.70 10.89 86.10 13.17 71.60 333.28
T60SO005 55.91 6.94 59.50 8.23 22.31 3.41 53.20 209.50 67.10 7.04 78.70 10.89 86.10 13.17 72.89 335.89
T65
T65WG012 108.34 13.05 15.28 6.89 3.15 0.48 124.03 271.22
T65WG013 163.34 19.62 15.28 6.89 3.15 0.48 186.92 395.68
T65WG014 178.31 21.41 33.57 16.18 3.15 0.48 204.04 457.14
W25
W25AO002 0.91 0.04 0.09 0.79 0.00 0.00 1.38 3.21
W25AO003 1.32 0.06 0.09 0.79 0.00 0.00 2.01 4.27
W25AO004 1.30 0.06 0.18 1.08 0.00 0.00 1.97 4.59
2-310
2 258
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

W25 cont.
W25AO005 2.63 0.11 0.36 1.66 0.00 0.00 3.99 8.75
W25AO006 2.04 0.09 0.09 0.79 0.00 0.00 3.09 6.10
W25CJ001 10.78 0.66 1.33 0.72 0.00 0.00 14.88 28.37
W25CJ002 16.75 1.03 1.60 0.87 0.00 0.00 23.12 43.37
W25CJ003 26.47 1.62 1.60 0.87 0.00 0.00 36.53 67.09
W25KZ001 1.47 0.19 0.00 0.00 0.00 0.00 1.00 2.66
W25KZ002 1.63 0.21 0.00 0.00 0.00 0.00 1.11 2.95
W25KZ003 1.67 0.22 0.00 0.00 0.00 0.00 1.13 3.02
W25KZ004 2.37 0.31 0.00 0.00 0.00 0.00 1.61 4.29
W25KZ005 2.80 0.36 0.00 0.00 0.00 0.00 1.90 5.06
W25KZ006 2.86 0.37 0.00 0.00 0.00 0.00 1.94 5.17
W25KZ007 3.05 0.40 0.00 0.00 0.00 0.00 2.07 5.52
W25NL001 15.52 0.68 18.05 7.81 0.00 0.00 25.69 67.75
W25NL002 26.23 1.15 52.61 6.38 0.00 0.00 43.41 129.78
W25NL003 16.83 0.73 23.56 2.85 0.00 0.00 27.85 71.82
W25NL004 33.82 1.51 5.34 0.65 0.69 0.11 56.24 98.36
W25NL005 64.59 2.82 109.94 13.32 0.00 0.00 106.90 297.57
W25SD001 1.14 0.05 0.45 0.19 0.00 0.00 1.73 3.56
W25SD002 2.94 0.13 0.27 0.12 0.00 0.00 4.46 7.92
W25SD003 1.77 0.08 5.82 0.60 0.00 0.00 2.68 10.95
W25SD004 2.52 0.11 2.59 0.27 0.04 0.01 3.84 9.38
W25SD005 1.33 0.06 3.88 0.40 0.00 0.00 2.02 7.69
W25SD006 1.21 0.05 0.09 4.04 0.00 0.00 1.84 7.23
W25SD007 1.29 0.06 0.09 5.04 0.00 0.00 1.96 8.44
W25SD008 1.40 0.06 0.09 6.04 0.00 0.00 2.13 9.72
W25SD009 3.11 0.14 0.99 6.43 0.00 0.00 4.73 15.40
W25XX005 0.42 0.02 1.62 0.17 0.00 0.00 0.64 2.87
2-311
2 259
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14

W25 cont.
W25XX006 0.59 0.03 1.62 0.17 0.00 0.00 0.90 3.31
W25XX007 0.80 0.03 2.59 0.27 0.00 0.00 1.21 4.90
W25XX008 0.82 0.04 3.56 0.37 0.00 0.00 1.25 6.04
W25XX009 1.66 0.07 2.59 0.27 0.00 0.00 2.53 7.12
W25XX010 2.55 0.11 7.76 0.80 0.00 0.00 3.87 15.09
W30
W30SO001 3.58 0.43 1.77 0.19 0.49 0.07 2.89 9.42
W30SO002 4.29 0.51 1.77 0.19 0.49 0.07 3.47 10.79
W30SO003 4.69 0.55 1.77 0.19 0.49 0.07 3.78 11.54
W30SO004 2.39 0.27 0.00 0.01 0.00 0.00 1.59 4.26
W30SO005 2.67 0.30 0.00 0.01 0.00 0.00 1.78 4.76
W30SO006 3.07 0.35 0.00 0.01 0.00 0.00 2.05 5.48
W35
W35LC012 0.61 0.04 1.00 0.43 0.00 0.00 0.42 2.50
W35LC013 0.66 0.04 1.17 0.51 0.00 0.00 0.45 2.83
W35LC018 0.11 0.01 0.14 0.06 0.00 0.00 0.07 0.39
W35LC021 0.39 0.02 0.57 0.25 0.00 0.00 0.27 1.50
W35XX020 0.25 0.02 2.98 0.31 0.00 0.00 0.27 3.83
W35XX021 0.63 0.06 4.60 0.48 0.03 0.00 0.70 6.50
W35XX022 0.65 0.06 4.87 0.50 0.03 0.00 0.72 6.83
W35XX023 1.14 0.10 12.18 1.26 0.03 0.00 1.26 15.97
W35XX024 1.69 0.15 6.37 0.66 0.03 0.00 1.87 10.77
W35XX025 1.62 0.14 5.57 0.58 0.03 0.00 1.80 9.74
2-312
2 260
EP 1110-1-8, Vol. 2
30 Apr 14
CHAPTER 3
Adjustments to Hourly Rates
SECTION I. GENERAL
3.1 Contents. This chapter explains the procedures for adjusting the hourly rates
shown in tables 2-1 and 2-2.
3.2 Basis for Equipment Rates. The rates shown in tables 2-1 and 2-2 are based on
the catalog list price of equipment manufactured in 2011 (3 years old). Area factors
used to compute regional ownership and operating expenses are listed in appendix B.
All equipment hourly rate elements for average and severe conditions are given in
table 2-2. Individual cost elements, which comprise the total hourly rate, are shown in
table 2-2. These hourly rate elements are listed by equipment ID No., which
corresponds to the equipment shown in tables 2-1 and 2-2.
a. Ownership costs consist of two cost elements: depreciation (DEPR) and facilities
capital cost of money (FCCM). These elements are located in tables 2-1 and 2-2.
b. Operating costs consist of five cost elements: fuel (FUEL); filters, oil, and grease
(FOG); repairs (REPAIR); tire wear (TIRE WEAR); and tire repair (TIRE REPAIR).
These elements are located in table 2-2.
3.3 Equipment Rate Adjustment Tables. Table 3-1 is used to adjust the ownership
(DEPR + FCCM) portion of the average hourly rate and table 3-2 is used to adjust the
standby hourly rate shown in table 2-1.
3.4 Determination for Use of Equipment Rates in Tables 2-1 and 2-2. The
predetermined equipment rates in tables 2-1 and 2-2 may be used when the
contractor’s actual cost data (cost or pricing data) is insufficient to calculate the rates. If
the contractor’s actual equipment is listed in tables 2-1 and 2-2, the equipment must be
equivalent. However, if the contractor’s actual equipment is not listed in tables 2-1 and
2-2, an equivalent piece of equipment may be chosen from the tables. To be
considered equivalent, the contractor’s equipment must be no more or less than
10.00 percent of the configuration (size, capacity, and horsepower) and value as
compared to the equipment in tables 2-1 and 2-2. In either case, if the equipment is not
equivalent, the equipment rate must be calculated using the methodology in chapter 2.
SECTION II. RATE ADJUSTMENTS
3.5 Rate Adjustments. The ownership and/or the operating portion of the hourly rates
and standby hourly rates shall be adjusted whenever one or more of the following rate
3-1
EP 1110-1-8, Vol. 2
30 Apr 14
adjustment conditions exist (rate adjustments are explained in detail in the following
paragraphs).
a. Changes in operating conditions.

b. Changes in Cost of Money Rate.
c. Actual work hours (hrs) exceed 40 hr per week (wk).
d. Changes in FUEL cost.
e. Adjustments to FOG cost.
f. Equipment of different age than table 2-1.
g. Rate adjustment for overage equipment.
h. Rate adjustment for overage equipment standby.
There are no rate adjustments for appendix B factors except for fuel cost (electric, gas,
diesel off-road, and diesel on-road) and the Cost of Money Rate. Also, there are no rate
adjustments for repairs, tire wear, or tire repair.
3.6 Changes in Operating Conditions. If difficult or severe conditions are justified by

the Contracting Officer, selection or calculation of the appropriate rate is necessary.
See chapter 2, section II, for definition of average, difficult, or severe conditions and
determination of condition.
3.7 Change in Cost of Money Rate (CMR). The Department of the Treasury adjusts
the CMR (Prompt Payment Interest Rate) on or about 1 January and 1 July each year;
these revisions are printed in the Federal Register. The Internet address for Prompt
Payment Interest Rate is http://www.treasurydirect.gov/govt/rates/tcir/tcir_
opdprmt2.htm. If the CMR shown in chapter 2, section VII, is not the current rate, the
FCCM portion of the total hourly rate shall be adjusted upward or downward to match
the CMR for the period of equipment use. See appendix I for a listing of historical
CMRs. The total hourly rate adjusted for a differing CMR is computed by the formula:
(NEW CMR)
Total Hourly Rate = DEPR/hr + [(FCCM/hr) x ] + Operating Costs/hr
(Old CMR)
Example: Assume that table 2-1 includes a crane [category (CAT) C80, subcategory
(SUB) 0.02] with hourly costs as shown in the following example. The CMR has
increased from 5.00 percent to a current rate of 6.00 percent (increase of 20.00
percent). The total hourly rate for this piece of equipment is determined as follows:
Assumptions for Total Hourly Rate with CMR of 5.00 percent (per hour):
DEPR $30.00
FCCM $10.00
Operating Costs (FUEL, FOG, TIRE WEAR, TIRE REPAIR, and REPAIR) $40.00
Total Hourly Rate (Based on a 40 hr/wk) $80.00
3-2
EP 1110-1-8, Vol. 2
30 Apr 14
Adjustment Calculation of Total Hourly Rate for New CMR of 6.00 percent
(per hour):
(6.00%)
$30.00/hr + [($10.00/hr) x ] + $40.00/hr = $82.00/hr
(5.00%)
3.8 Actual Work Hours Greater than 40 Hours per Week. If the actual number of work
hours per week is greater than 40 hours, an adjustment shall be made to the FCCM
element of the ownership cost. The FCCM is to be paid up to a maximum of 40 hours
per week (7 calendar days). To calculate a multi-shift rate, prorate the 40-hour FCCM
over the actual hours per week, as follows:
Example: Assume that table 2-1 includes a crane (category C80, subcategory 0.02)
with the below hourly costs. This crane worked 10 hours per day, 6 days per week (60
hours per week). The total hourly rate for this piece of equipment is determined as
follows:
(40 hr/wk)
Total Hourly Rate = DEPR/hr + [(FCCM/hr) x ] + Operating Costs/hr
(Actual Work hr/wk)
Assumptions for Total Hourly Rate for 40 Hours/Week:
DEPR $30.00
FCCM $10.00
Operating Costs (FUEL, FOG, TIRE WEAR, TIRE REPAIR, and REPAIR) $40.00
Total Hourly Rate (Based on a 40 hr/wk) $80.00
Adjustment Calculation of Total Hourly Rate for 60 Hours/Week:
(40 hr/wk)
$30.00/hr + [$10.00/hr) x ] + $40.00/hr = $76.67/hr
(60 hr/wk)
3.9 Changes in Fuel Cost. Hourly fuel costs (including electricity) shall be adjusted in
the event the average fuel prices at the jobsite vary by more than 10.00 percent above
or below the price in appendix B. The contractor shall be required to furnish copies of
all fuel supply contracts and invoices to the government to support fuel cost adjustment.
Request for upward adjustment in the rates will be considered only when fuel is
supplied by recognized distributors of bulk quantities. Mathematically, this is the ratio of
the new fuel cost divided by the fuel cost (appendix B). To calculate the total hourly
rate, apply the ratio of fuel cost, as follows:
3-3
EP 1110-1-8, Vol. 2
30 Apr 14
with the below hourly costs. Assume the fuel cost (diesel off-road) in appendix B is
$3.50/gal and the current fuel cost has increased to $4.20/gal (increase of 20.00
percent). The total hourly rate for this piece of equipment can be determined as follows:
Total Hourly Rate = (DEPR/hr + FCCM/hr) + (FOG/hr + TIRE WEAR/hr + TIRE REPAIR/hr +
REPAIR/hr) + [
(New Fuel Cost ) x FUEL/hr]
(Fuel Cost in Appendix B)
Assumptions for Fuel Cost (based on $3.50/gal from appendix B) per hour:
DEPR $30.00
FCCM $10.00
FOG, TIRE WEAR, TIRE REPAIR, and REPAIR $30.00
FUEL $10.00
Total Hourly Rate $80.00
Adjustment Calculation for hourly FUEL cost using the new fuel cost of $3.00/gal:
($4.20/gal)
($30.00/hr + $10.00/hr) + $30.00/hr + [ x $10.00/hr] = $82.00/hr
($3.50/gal)
3.10 Adjustments to Filters, Oil, and Grease (FOG) Cost. The hourly FOG allowance
shall also be adjusted upward or downward by applying the same ratio (new fuel cost
divided by fuel cost shown in appendix B) as the fuel costs change using the
methodology as shown in paragraph 3.9.
3.11 Equipment of Different Age than Table 2-1. When the age of the equipment is
newer or older than the age of the equipment listed in table 2-1, table 3-1 factors may
be used to adjust the hourly rate (see paragraph 3.12 for guidance on overage
equipment), otherwise the step-by-step calculation method (as shown in figure 2-1) is
necessary. To adjust the hourly rate using the tables, the factors given in table 3-1 are
multiplied by the hourly ownership costs shown in table 2-1. The result is an ownership
rate adjusted for the actual age of the equipment. Note: Age adjustment factors in
tables 3-1 and 3-2 vary by region.
a. When the age of a unit of equipment is older than the age of the equipment
listed in table 2-1 (purchased new in 2011) and does not exceed the years of economic
life, adjust the hourly rate as shown in the next example. The years of economic life is
determined by dividing hours of LIFE (from appendix D) by Working Hours Per Year
(WHPY) (from appendix B).
3-4
EP 1110-1-8, Vol. 2
30 Apr 14
manufactured in 2011 and has a total hourly rate of $65 per hour and an ownership rate
of $30 per hour. If an equivalent crane owned by a contractor was manufactured in
2007, the total hourly rate is determined as follows:
Table 2-1 Rate and Adjustment Calculation:
Total hourly rate = $65.00/hr

Ownership rate 2011 (DEPR + FCCM) = -($30.00)/hr
Ownership rate 2007 adjusted for age
(Ownership rate = $30) x (0.93 the age adjustment
factor from table 3-1, for category C80,
subcategory 0.02, and for the year 2007.) = +$27.90/hr
Total hourly rate for equipment manufactured in 2007 = $62.90/hr
b. When the unit of equipment is older than the age of equipment listed in
table 2-1 (purchased new in 2011) and exceeds the years of economic life, adjust the
hourly rate as shown in the example for overage equipment in paragraph 3.12.
c. When the unit of equipment is newer than the equipment listed in table 2-1
(purchased new in 2011), use the adjustment factor in table 3-1 for the year of
manufacture. If the equipment is newer than the most recent year shown in table 3-1,
use the adjustment factor in the column of the most recent year. Once the adjustment
factor is determined from table 3-1, complete the adjustment calculation as shown in the
example above. The step-by-step calculation method shown in figure 2-1 may also be
used.
3.12 Rate Adjustment for Overage Equipment. If the contractor’s equipment exceeds
the economic life in hours (from appendix D), it is considered overage, and the rates
shall be adjusted.
a. The total hourly operating rate for overage equipment (no matter how old) shall
be computed on the basis that the equipment is as old as possible "without" exceeding
the hours of LIFE as shown in appendix D. Tables 3-1 and 3-2 show factors for the
economic life for equipment based on the current pamphlet year (e.g., manufactured in
2011). Select a comparable unit of equipment (horsepower, value, capacity, and size)
shown in table 2-1, the total hourly rate can be computed as shown in the following
example. If there is no comparable unit of equipment in table 2-1, follow the
methodology presented in figure 3-1.
b. The ownership portion of the rate shall be adjusted for equipment that is
overage. This adjusted rate is not to exceed the rate for the same unit of equipment
that is not overage.
3-5
EP 1110-1-8, Vol. 2
30 Apr 14
manufactured in 2011, has a total hourly rate of $65 per hour, and an ownership rate of
$30 per hour. If an equivalent crane owned by a contractor was manufactured in 1997
(maximum life 2003), this crane is overage and the total hourly rate is determined as
follows:
Table 2-1 Rate and Adjustment Calculation:
Total hourly rate = $65.00/hr

Ownership rate 2011 (DEPR + FCCM) = -($30.00)/hr
Ownership rate 1997 adjusted for age
(Ownership rate = $30.00) x (0.79) use the oldest age
adjustment factor from table 3-1, for category C80,
subcategory 0.02, the last year shown.) = +$23.70/hr
Total hourly rate for equipment manufactured in 1997 = $58.70/hr
3.13 Standby Rate Adjustment for Equipment of a Different Age than Table 2-1. If the
equipment age is other than listed in table 2-1 (purchased new in 2011), adjustment to
the hourly standby rate is required. When the age of the equipment is newer or older
than the age of the equipment listed in table 2-1, table 3-2 factors may be used to adjust
the hourly rate, otherwise the step-by-step calculation method is necessary. The result
is a standby rate adjusted for the actual age of the equipment.
a. Standby rates for overage equipment are based on the actual age of the
equipment. The age adjustment factor given in table 3-2 is multiplied by the hourly
standby cost shown in table 2-1 for the listed or comparable unit of equipment. This
results in a standby rate adjusted for the actual age of the unit of equipment being
considered.
Hourly Standby Rate Adjusted for Actual Age =

Hourly Standby Rate x Age Adjustment Factor
manufactured in 2011 and has a standby rate of $20.00 per hour. If an equivalent crane
owned by a contractor was manufactured in 2003, the hourly standby rate is determined
as follows:
Hourly Standby Rate (table 2-1) = $20.00/hr

Age Adjustment Factor (table 3-2) = 0.79
for category C80, subcategory 0.02, and for 2003 (actual year of
manufacture)
3-6
EP 1110-1-8, Vol. 2
30 Apr 14
Adjustment Calculation:
Hourly Standby Rate Adjusted for Actual Age =$20.00/hr

(Hourly Standby Rate) x 0.79 (Age Adjustment Factor) =$15.80/hr
b. When the unit of equipment is newer than the equipment listed in

table 2-1 (purchased new in 2011), use the adjustment factor in table 3-2 for the year
of manufacture. Once the adjustment factor is determined from table 3-2, complete the
adjustment calculation as shown in the example above. The step-by-step calculation
method shown in figure 3-2 may also be used.
c. When the equipment age is older than the last year shown in table 3-2 or newer
than the first year shown in table 3-2, the standby rate must be calculated using the
step-by-step methodology shown in figure 3-2.
3.14 Equipment Purchased Used. A detailed methodology for computing a total hourly
rate for equipment purchased used is not included in this pamphlet.
a. When actual cost data in accordance with chapter 1 is not available, an hourly
rate and standby rate for equipment purchased used can be computed on the basis that
the equipment was purchased new by the contractor in the year it was manufactured.
Consideration for the actual age of used equipment may require an adjustment for
overage.
b. The condition of the used equipment at the time of purchase should consider
the extent of capital improvements, mechanical condition, and previous hours of
operation. These conditions are difficult or impossible to determine and evaluate when
computing a total hourly rate based on actual acquisition cost.
3.15 Rate Calculation Examples. Figure 3-1 illustrates how total hourly rates are
adjusted for overage equipment. Figure 3-2 gives a sample calculation for computing
adjusted standby rates.
3-7
EP 1110-1-8, Vol. 2
30 Apr 14
Table 3-1. Equipment Age Adjustment Factors
for
Ownership Costs
The factors in this table are used when the age of a unit of equipment is other than the
age of the equipment listed in table 2-1 (purchased new in 2011).
The factors are multiplied by the hourly ownership costs (shown in table 2-1) and result
in an ownership rate adjusted for the actual age of the equipment being considered.
When the actual “life” in hours of the unit of equipment has exceeded the economic life
given in appendix D, the age will be determined as discussed in chapter 3.
Refer to chapter 3, as follows:
3.11. Equipment of Different Age than Table 2-1
3.12. Rate Adjustment for Overage Equipment
3-8
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14
4/30/2014
Table 3-1 Equipment Age Adjustment Factors for Ownership Cost
Life in Years Year Purchased New
CATEGORY REGION 2
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
SUB TYPE OF EQUIPMENT 2014 2013 2012 2011 2010 2009 2008 2007 2006 2005 2004 2003 2002 2001 2000 1999 1998 1997
A10 0.00 AGGREGATE / CHIP SPREADERS
A10 0.10 SELF-PROPELLED 1.08 1.05 1.03 1.00 0.97 0.97

A10 0.20 TOWED & TAILGATE 1.08 1.06 1.03 1.00 0.97
A15 0.00 AIR COMPRESSORS, PORTABLE
A15 0.10 ROTARY SCREW 1.11 1.09 1.04 1.00 0.91 0.91 0.85
A15 0.20 SHOP TYPE 1.11 1.09 1.04 1.00 0.92 0.91 0.86 0.80 0.76
A20 0.00 AIR HOSE, TOOLS & EQUIPMENT
A20 0.10 AIR DRILL HOSE 1.09 1.08 1.03 1.00

A20 0.20 SANDBLAST HOSE 1.09 1.08 1.03 1.00
A20 0.30 SANDBLASTERS, BREAKERS, & MISC. AIR TOOLS 1.10 1.08 1.04 1.00 0.92
A25 0.00 ASPHALT PAVING DISTRIBUTORS 1.07 1.05 1.03 1.00 0.97
A30 0.00 ASPHALT PAVERS & MISCELLANEOUS ROAD EQUIPMENT
A30 0.10 SELF PROPELLED 1.08 1.05 1.03 1.00 0.97 0.97
A30 0.20 TOWED 1.08 1.05 1.03 1.00 0.97 0.97 0.93
A30 0.30 SLURRY SEAL PAVERS (Cold mix) 1.08 1.05 1.03 1.00 0.97 0.97 0.93 0.89 0.86
A30 0.40 MISCELLANEOUS ROAD EQUIPMENT 1.08 1.05 1.03 1.00 0.97 0.97 0.93
A35 0.00 ASPHALT PAVING KETTLES 1.08 1.06 1.03 1.00 0.97
A40 0.00 ASPHALT & CONCRETE MILLERS / PROFILERS / PLANERS / ROTARY 1.08 1.06 1.03 1.00 0.97
GRINDERS
A45 0.00 ASPHALT RECYCLERS & SEALERS 1.08 1.06 1.03 1.00
B10 0.00 BATCH PLANTS, ASPHALT & CONCRETE
B10 0.10 ASPHALT 1.08 1.05 1.03 1.00 0.97 0.97

B10 0.20 CONCRETE 1.08 1.05 1.03 1.00 0.97 0.97
3- 9
3-9
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14
4/30/2014
CATEGORY REGION 2
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
B10 0.30 PUGMILL 1.08 1.05 1.03 1.00 0.97 0.97 0.93
B15 0.00 BROOMS, STREET SWEEPERS & FLUSHERS 1.09 1.08 1.05 1.00 0.97 0.96
B20 0.00 BRUSH CHIPPERS 1.09 1.08 1.05 1.00 0.97 0.96
B25 0.00 BUCKETS, CLAMSHELL 1.05 1.04 1.01 1.00 0.97 0.97
B30 0.00 BUCKETS, CONCRETE
B30 0.10 GENERAL PURPOSE, MANUAL TRIP 1.05 1.04 1.01 1.00 0.97 0.97
B30 0.20 LAYDOWN 1.05 1.04 1.01 1.00 0.97 0.97
B30 0.30 LOWBOY 1.05 1.04 1.01 1.00 0.97 0.97
B30 0.40 LOW SLUMP 1.05 1.04 1.01 1.00 0.97 0.97
B35 0.00 BUCKETS, DRAGLINE
B35 0.10 LIGHT WEIGHT 1.05 1.04 1.01 1.00 0.97 0.97
B35 0.20 MEDIUM WEIGHT 1.05 1.04 1.01 1.00 0.97 0.97 0.95
B35 0.30 HEAVY WEIGHT 1.05 1.04 1.01 1.00 0.97 0.97 0.95
C05 0.00 CHAIN SAWS 1.09 1.08 1.00
C10 0.00 COMPACTORS, WALK-BEHIND OR REMOTE CONTROLLER
C10 0.10 COMPACTORS, RAMMERS / TAMPERS & VIBRATORY PLATES 1.09 1.07 1.04 1.00
C10 0.20 ROLLERS, VIBRATORY 1.10 1.08 1.05 1.00
C15 0.00 CONCRETE CLEANERS / ABRASIVE BLASTERS
C15 0.10 WALK BEHIND 1.10 1.09 1.05 1.00

C15 0.20 TRUCK/TRAILER MOUNTED 1.10 1.09 1.05 1.00 0.96 0.96
C20 0.00 CONCRETE BUGGIES 1.10 1.09 1.05 1.00
C25 0.00 CONCRETE FINISHERS/SCREEDS/SPREADERS
3- 10
3-10
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14
4/30/2014
CATEGORY REGION 2
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
C25 0.10 FINISHERS/TROWELS 1.10 1.09 1.05 1.00

C25 0.20 VIBRATORY SCREED 1.10 1.09 1.05 1.00
C25 0.25 VIBRATORY LASER SCREED 1.12 1.10 1.06 1.00 0.96 0.95
C25 0.30 MATERIAL/TOPPING SPREADERS 1.12 1.10 1.06 1.00 0.96 0.95
C30 0.00 CONCRETE GRINDERS 1.10 1.09 1.05 1.00
C35 0.00 CONCRETE GUNITERS / SHOTCRETERS 1.11 1.09 1.05 1.00 0.96
C40 0.00 CONCRETE MIXING UNITS 1.10 1.09 1.05 1.00
C45 0.00 CONCRETE PAVING MACHINES 1.08 1.06 1.03 1.00 0.97
C55 0.00 CONCRETE PUMPS 1.09 1.08 1.05 1.00 0.97 0.96
C60 0.00 CONCRETE SAWS (Add cost for sawblade wear) 1.09 1.08 1.05 1.00 0.97
C65 0.00 CONCRETE VIBRATORS 1.10 1.08 1.04 1.00
C70 0.00 CRANES, GANTRY & STRADDLE
C75 0.00 CRANES, HYDRAULIC, SELF-PROPELLED 1.06 1.04 1.02 1.00 0.97 0.97 0.94 0.93 0.92 0.86
C80 0.00 CRANES, HYDRAULIC, TRUCK MOUNTED
C80 0.01 UNDER 26 TON 1.06 1.04 1.02 1.00 0.97 0.97 0.94 0.93 0.92 0.86
C80 0.02 26 TON THRU 65 TON 1.06 1.04 1.02 1.00 0.97 0.97 0.94 0.93 0.92 0.86 0.81 0.79
C80 0.03 66 TON THRU 125 TON 1.06 1.04 1.02 1.00 0.97 0.97 0.94 0.93 0.92 0.86 0.81 0.79 0.76
C80 0.04 OVER 125 TON 1.06 1.04 1.02 1.00 0.97 0.97 0.94 0.93 0.92 0.86 0.81 0.79 0.76 0.71
C85 0.00 CRANES, MECHANICAL, LATTICE BOOM, CRAWLER MOUNTED
C85 0.11 DRAGLINE, CLAMSHELL, 0 THRU 1.0 CY 1.06 1.04 1.02 1.00 0.96 0.97 0.94 0.93 0.91 0.86
C85 0.12 DRAGLINE, CLAMSHELL, OVER 1.0 CY THRU 2.5 CY 1.06 1.04 1.02 1.00 0.96 0.97 0.94 0.93 0.92 0.86 0.80 0.77
C85 0.13 DRAGLINE, CLAMSHELL, OVER 2.5 CY THRU 5.0 CY 1.06 1.04 1.02 1.00 0.96 0.97 0.94 0.93 0.92 0.86 0.80 0.77 0.75
3- 11
3-11
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14
4/30/2014
CATEGORY REGION 2
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
C85 0.14 DRAGLINE, CLAMSHELL, OVER 5.0 CY 1.06 1.04 1.02 1.00 0.96 0.97 0.94 0.93 0.92 0.86 0.80 0.78 0.75 0.69
C85 0.21 LIFTING, 0 THRU 25 TON 1.06 1.04 1.02 1.00 0.96 0.97 0.94 0.93 0.92 0.86 0.80 0.77
C85 0.22 LIFTING, 26 TON THRU 50 TON 1.06 1.04 1.02 1.00 0.96 0.97 0.94 0.93 0.92 0.86 0.80 0.77 0.75
C85 0.23 LIFTING, 51 TON THRU 150 TON 1.06 1.04 1.02 1.00 0.97 0.97 0.94 0.93 0.92 0.86 0.81 0.79 0.76 0.71
C85 0.24 LIFTING, OVER 150 TON 1.05 1.04 1.02 1.00 0.97 0.97 0.94 0.93 0.92 0.86 0.81 0.79 0.76 0.71 0.72 0.72
C90 0.00 CRANES, MECHANICAL, LATTICE BOOM, TRUCK MOUNTED
C90 0.01 UNDER 26 TON 1.06 1.04 1.02 1.00 0.97 0.97 0.94 0.93 0.92 0.86
C90 0.02 26 TON THRU 65 TON 1.06 1.04 1.02 1.00 0.97 0.97 0.94 0.93 0.92 0.86 0.81 0.79
C90 0.03 66 TON THRU 125 TON 1.06 1.04 1.02 1.00 0.96 0.97 0.94 0.93 0.92 0.86 0.80 0.77 0.75
C90 0.04 OVER 125 TON 1.06 1.04 1.02 1.00 0.96 0.97 0.94 0.93 0.92 0.86 0.80 0.78 0.75 0.69
C95 0.00 CRANES, TOWER 1.06 1.04 1.02 1.00 0.96 0.97 0.94 0.93 0.92 0.86 0.80 0.77 0.75
D10 0.00 DRILLS, AIR/HYDRAULIC,CRWLR MTD,0" THRU 6.5" DIA HOLE (Add cost for
drill steel and bit wear)
D10 0.10 DRILLS, AIR TRACK (Add cost for drill steel and bit wear) 1.08 1.06 1.04 1.00 0.95 0.94 0.91 0.84 0.77 0.70
D10 0.20 DRILLS, HYDRAULIC TRACK (Add cost for drill steel and bit wear) 1.08 1.06 1.04 1.00 0.95 0.94 0.91
D15 0.00 DRILLS, HORIZONTAL
D15 0.10 DRILLS, HORIZONTAL BORING & GROUND PIERCING (Add cost for drill steel 1.08 1.06 1.04 1.00 0.95 0.94 0.91
and bit wear)
D15 0.20 DRILLS, HORIZONTAL & DIRECTIONAL (Add cost for drill steel and bit wear) 1.08 1.06 1.04 1.00 0.95 0.94 0.91
D20 0.00 DRILLS, CORE, COLUMN MOUNTED (Add cost for drill steel and bit wear) 1.08 1.06 1.04 1.00 0.95 0.94
D25 0.00 DRILLS, CORE & DOWELLING (Add cost for drill steel and bit wear) 1.08 1.06 1.04 1.00 0.95 0.94 0.91
D30 0.00 DRILLS, EARTH / AUGER (Add cost for drill steel and cutting edge wear) 1.08 1.06 1.04 1.00 0.95 0.94 0.91
D35 0.00 DRILLS, ROTARY BLASTHOLE (Add cost for drill steel and bit wear)
D35 0.11 DIESEL, 4.5" THRU 9.875" DIAMETER HOLE (Add cost for drill steel and bit 1.07 1.05 1.04 1.00 0.96 0.95 0.92 0.85 0.78 0.71
wear)
3- 12
3-12
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14
4/30/2014
CATEGORY REGION 2
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
D35 0.12 DIESEL, OVER 9.875" DIAMETER (Add cost for drill steel and bit wear) 1.07 1.05 1.04 1.00 0.96 0.95 0.92 0.85 0.78 0.72 0.65 0.61 0.59
D35 0.21 ELECTRIC, 4.5" THRU 9.875" DIAMETER HOLE (Add cost for drill steel and bit 1.07 1.05 1.04 1.00 0.96 0.95 0.92 0.85 0.78 0.71
wear)
D35 0.22 ELECTRIC, OVER 9.875" DIAMETER (Add cost for drill steel and bit wear) 1.07 1.05 1.04 1.00 0.96 0.95 0.92 0.85 0.78 0.72 0.65 0.61 0.59
F10 0.00 FORK LIFTS 1.10 1.08 1.05 1.00 0.96 0.96 0.92
G10 0.00 GENERATOR SETS
G10 0.10 PORTABLE 1.05 1.03 1.02 1.00 0.94 0.92

G10 0.20 SKID MOUNTED 1.05 1.03 1.02 1.00 0.94 0.92 0.89
G15 0.00 GRADERS, MOTOR 1.18 1.17 1.12 1.00 0.95 0.93 0.87 0.83 0.82 0.77
H10 0.00 HAMMERS, HYDRAULIC (Demolition tool) (Add cost for point wear) 1.10 1.09 1.05 1.00 0.96
H13 0.00 HAZARDOUS/TOXIC WASTE EQUIPMENT
H13 0.11 COMPACTORS (Compression force) 0 THRU 50 TONS 1.10 1.08 1.05 1.00 0.96 0.96 0.93
H13 0.12 COMPACTORS (Compression force) OVER 50 TONS 1.10 1.08 1.05 1.00 0.96 0.96 0.92 0.89 0.86
H13 0.21 FILTER PRESSES, STATIONARY 1.10 1.08 1.05 1.00 0.96 0.96 0.92
H13 0.22 FILTER PRESSES, MOBILE 1.10 1.08 1.05 1.00 0.96 0.96 0.93
H13 0.30 CENTRIFUGES 1.10 1.09 1.05 1.00
H13 0.40 SHREDDERS 1.10 1.08 1.05 1.00 0.96 0.96 0.93
H13 0.51 SOIL TREATMENT PLANT, MOBILE 1.10 1.08 1.05 1.00 0.96 0.96 0.93
H13 0.61 SLUDGE PROCESSING EQUIP, SLUDGE DISPENSERS 1.10 1.08 1.05 1.00 0.96 0.96 0.93
H13 0.71 WASTE HANDLING EQUIPMENT, DRUM HANDLING 1.10 1.08 1.05 1.00
H15 0.00 HEATERS, SPACE
H20 0.00 HOISTS & AIR WINCHES 1.10 1.09 1.05 1.00 0.96 0.96 0.92
H25 0.00 HYDRAULIC EXCAVATORS, CRAWLER MOUNTED
3- 13
3-13
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14
4/30/2014
CATEGORY REGION 2
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
H25 0.10 0 LBS THRU 12,500 LBS (COMPACT EXCAVATORS) 1.06 1.05 1.02 1.00 0.96 0.97
H25 0.11 OVER 12,500 LBS THRU 40,000 LBS 1.06 1.05 1.02 1.00 0.96 0.97
H25 0.12 OVER 40,000 LBS THRU 100,000 LBS 1.06 1.04 1.02 1.00 0.96 0.97 0.94 0.92 0.91
H25 0.13 OVER 100,000 LBS THRU 160,000 LBS 1.06 1.04 1.02 1.00 0.96 0.97 0.94 0.92 0.91 0.85 0.79 0.76
H25 0.14 OVER 160,000 LBS 1.06 1.04 1.02 1.00 0.96 0.97 0.94 0.93 0.91 0.85 0.79 0.76 0.74 0.67
H25 0.21 ATTACHMENTS, MOBILE SHEARS 1.10 1.08 1.05 1.00 0.96
H25 0.22 ATTACHMENTS, MATERIAL HANDLING 1.10 1.09 1.05 1.00 0.96
H25 0.23 ATTACHMENTS, CONCRETE PULVERIZERS 1.10 1.08 1.05 1.00 0.96
H25 0.24 ATTACHMENTS, COMPACTORS 1.10 1.08 1.05 1.00 0.96
H30 0.00 HYDRAULIC EXCAVATORS, WHEEL MOUNTED
H30 0.01 0 THRU 1.0 CY 1.06 1.05 1.02 1.00 0.96 0.97
H30 0.02 OVER 1.0 CY 1.06 1.05 1.02 1.00 0.96 0.97 0.94
H35 0.00 HYDRAULIC SHOVELS, CRAWLER MOUNTED
H35 0.11 DIESEL, 0 CY THRU 5.0 CY 1.06 1.04 1.02 1.00 0.96 0.97 0.94 0.93 0.91 0.86
H35 0.12 DIESEL, OVER 5.0 CY 1.06 1.04 1.02 1.00 0.96 0.97 0.94 0.93 0.92 0.86 0.80 0.77
H35 0.21 ELECTRIC, OVER 2.5 CY 1.06 1.04 1.02 1.00 0.96 0.97 0.94 0.93 0.92 0.86 0.80 0.77 0.75
L10 0.00 LAND CLEARING EQUIPMENT 1.13 1.11 1.06 1.00 0.95 0.96 0.93
L15 0.00 LANDSCAPING EQUIPMENT 1.10 1.08 1.05 1.00
L20 0.00 LIGHTING SETS, TRAILER MOUNTED
L20 0.10 METALLIC VAPOR 1.10 1.09 1.05 1.00 0.96 0.96
L25 0.00 LINE STRIPING EQUIPMENT 1.10 1.09 1.05 1.00 0.96 0.96
L30 0.00 LOADERS, BELT (Conveyor belts) & ACCESSORIES 1.10 1.08 1.05 1.00 0.96 0.96 0.92
3- 14
3-14
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14
4/30/2014
CATEGORY REGION 2
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
L35 0.00 LOADERS, FRONT END, CRAWLER TYPE 1.13 1.11 1.06 1.00 0.95 0.96 0.93
L40 0.00 LOADERS, FRONT END, WHEEL TYPE
L40 0.11 ARTICULATED, 0 THRU 225 HP 1.13 1.12 1.07 1.00 0.95 0.95 0.92
L40 0.12 ARTICULATED, OVER 225 HP 1.12 1.11 1.06 1.00 0.95 0.96 0.93 0.89 0.87 0.83
L40 0.20 SKID STEER 1.13 1.11 1.06 1.00 0.95 0.96
L40 0.21 SKID STEER ATTACHMENTS 1.13 1.11 1.06 1.00
L40 0.31 TOOL CARRIER & TELESCOPIC HANDLERS, 0 THRU 225 HP 1.13 1.12 1.07 1.00 0.95 0.95 0.92
L40 0.32 TOOL CARRIER & TELESCOPIC HANDLERS, OVER 225 HP 1.12 1.10 1.06 1.00 0.96 0.96 0.93 0.90 0.88
L45 0.00 LOADERS / BACKHOE, CRAWLER TYPE 1.13 1.11 1.06 1.00 0.95 0.96
L50 0.00 LOADERS / BACKHOE, WHEEL TYPE 1.13 1.12 1.07 1.00 0.95 0.95 0.92
L55 0.00 LOADER / BACKHOE, ATTACHMENTS 1.10 1.09 1.05 1.00 0.96
L60 0.00 LOG SKIDDERS 1.08 1.06 1.04 1.00 0.97 0.96 0.93
M10 0.00 MARINE EQUIPMENT (NON DREDGING)
M10 0.11 AQUATIC MAINTENANCE 1.06 1.03 1.01 1.00 0.97 0.95 0.91
M10 0.12 AQUATIC MAINTENANCE ATTACHMENTS 1.06 1.03 1.02 1.00 0.97
M10 0.21 HYDRAULIC CUTTERHEAD DREDGE, 8" OR LESS,TRANSPORTABLE 1.05 1.03 1.01 1.00 0.98 0.95 0.91 0.88 0.84 0.80 0.77 0.73
M10 0.22 HYDRAULIC CUTTERHEAD DREDGE,8" - 12",TRANSPORTABLE 1.05 1.03 1.01 1.00 0.98 0.95 0.91 0.88 0.84 0.80 0.77 0.73
M10 0.23 HYDRAULIC AUGERHEAD DREDGE,12" OR LESS,TRANSPORTABLE 1.05 1.03 1.01 1.00 0.98 0.95 0.91 0.88 0.84 0.80 0.77 0.73
M10 0.24 HYDRAULIC FLOATING PUMPS,12" OR LESS,TRANSPORTABLE 1.05 1.03 1.01 1.00 0.98 0.95
M10 0.25 HYDRAULIC DREDGE PUMPS,12" OR LESS,TRANSPORTABLE 1.06 1.03 1.01 1.00 0.97
M10 0.26 HYDRAULIC DREDGE / PUMP ATTACHMENTS 1.06 1.03 1.01 1.00 0.97
M10 0.31 SMALL MECH DREDGES,CLAMSHELL,BARGE-MTD TO 5 CY 1.06 1.04 1.02 1.00 0.97 0.97 0.94 0.93 0.92 0.86 0.81 0.79 0.76
3- 15
3-15
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14
4/30/2014
CATEGORY REGION 2
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
M10 0.32 SMALL MECH DREDGES, AMPHIBIOUS EXCAVATORS 1.06 1.04 1.02 1.00 0.96 0.97 0.94
M10 0.33 SMALL MECH DREDGES,HOE-MOUNTED DREDGING ATTACH 1.06 1.03 1.01 1.00 0.97 0.95 0.91 0.87 0.83 0.79 0.76 0.71 0.68 0.67
M10 0.41 WORK FLOATS (NON-DREDGING) 1.05 1.03 1.01 1.00 0.98
M10 0.42 WORK BARGES (SECTIONAL, NON-DREDGING) 1.05 1.03 1.01 1.00 0.98 0.95 0.91 0.88 0.84 0.81 0.78 0.73 0.70 0.69 0.67 0.66 0.65 0.64
M10 0.45 FLAT-DECK OR CARGO BARGE (NON-DREDGING) 1.05 1.02 1.01 1.00 0.98 0.96 0.92 0.89 0.85 0.82 0.79 0.75 0.72 0.71 0.69 0.68 0.67 0.66
M10 0.46 DUMP SCOW (NON-DREDGING) 1.05 1.02 1.01 1.00 0.98 0.96 0.92 0.89 0.85 0.82 0.79 0.75 0.72 0.71 0.69 0.68 0.67 0.66
M10 0.47 DRILL BARGE (NON-DREDGING) 1.05 1.03 1.01 1.00 0.98 0.96 0.92 0.88 0.84 0.81 0.78 0.74 0.71 0.70 0.68 0.67 0.67 0.66
M10 0.48 ALL OTHER BARGES (NON-DREDGING) 1.05 1.03 1.01 1.00 0.98 0.96 0.92 0.88 0.84 0.81 0.78 0.74 0.71 0.70 0.68 0.67 0.67 0.66
M10 0.51 BOATS & LAUNCHES, 0 THRU 250 HP 1.06 1.03 1.01 1.00 0.97 0.95 0.91 0.87 0.83 0.79 0.76 0.71
M10 0.53 BOATS & LAUNCHES, 251 THRU 500 HP 1.05 1.03 1.01 1.00 0.98 0.95 0.91 0.88 0.84 0.80 0.77 0.73 0.69
M10 0.54 TUGS, 501 THRU 1,000 HP 1.05 1.03 1.01 1.00 0.98 0.95 0.91 0.88 0.84 0.81 0.78 0.73 0.70 0.69 0.67 0.66 0.66 0.64
M10 0.55 TUGS, 1,000 THRU 2,000 HP 1.05 1.03 1.01 1.00 0.98 0.95 0.91 0.88 0.84 0.81 0.78 0.74 0.70 0.69 0.68 0.67 0.66 0.65
P10 0.00 PILE HAMMER ACCESSORIES - EXTRACTORS & BOX LEADS 1.13 1.11 1.06 1.00 0.95
P20 0.00 PILE HAMMERS, DOUBLE ACTING
P20 0.10 DIESEL 1.11 1.09 1.06 1.00 0.96

P20 0.20 PNEUMATIC (STEAM/AIR) 1.10 1.09 1.05 1.00 0.96
P25 0.00 PILE HAMMERS, SINGLE ACTING
P25 0.10 DIESEL 1.10 1.09 1.05 1.00 0.96

P25 0.20 PNEUMATIC (STEAM/AIR) 1.10 1.08 1.05 1.00 0.96
P30 0.00 PILE HAMMERS, DRIVER/ EXTRACTOR, VIBRATORY 1.10 1.09 1.05 1.00 0.96
P35 0.00 PIPELAYERS 1.12 1.11 1.06 1.00 0.96 0.96 0.93 0.89 0.87 0.83
P40 0.00 PLATFORMS & MAN-LIFTS 1.05 1.04 1.01 1.00 0.97 0.97
3- 16
3-16
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14
4/30/2014
CATEGORY REGION 2
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
P45 0.00 PUMPS, GROUT 1.10 1.08 1.05 1.00 0.96 0.96
P50 0.00 PUMPS, WATER, CENTRIFUGAL, TRASH
P50 0.11 ENGINE DRIVE 1.10 1.09 1.05 1.00 0.96 0.96
P50 0.12 ELECTRIC DRIVE 1.10 1.09 1.05 1.00 0.96 0.96
P50 0.21 WHEEL MOUNTED, ENGINE DRIVE 1.10 1.09 1.05 1.00 0.96 0.96
P50 0.22 WHEEL MOUNTED, ELECTRIC DRIVE 1.10 1.09 1.05 1.00 0.96 0.96
P50 0.31 HOSES, PUMP, SUCTION & DISCHARGE 1.09 1.08 1.05 1.00
P55 0.00 PUMPS, WATER, SUBMERSIBLE
P55 0.01 ENGINE DRIVE 1.10 1.09 1.05 1.00 0.96 0.96
P55 0.02 ELECTRIC DRIVE 1.10 1.08 1.05 1.00 0.96 0.96
P60 0.00 PUMPS, WATER, CENTRIFUGAL, DEWATERING
P60 0.11 SKID MOUNTED, ENGINE DRIVE 1.10 1.09 1.05 1.00 0.96 0.96
P60 0.12 SKID MOUNTED, ELECTRIC DRIVE 1.10 1.08 1.05 1.00 0.96 0.96
P65 0.00 PUMPS, WATER, DIAPHRAGM
P65 0.11 SKID MOUNTED, ENGINE DRIVE 1.10 1.09 1.05 1.00 0.96 0.96
P65 0.12 SKID MOUNTED, ELECTRIC DRIVE 1.10 1.08 1.05 1.00 0.96 0.96
P70 0.00 PUMPS, WATER (For core drills)
P70 0.01 ENGINE DRIVE 1.11 1.09 1.05 1.00 0.96 0.96
3- 17
3-17
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14
4/30/2014
CATEGORY REGION 2
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
P70 0.02 ELECTRIC DRIVE 1.11 1.09 1.05 1.00 0.96 0.96
R10 0.00 RIPPERS & HYDRAULIC BANK SLOPERS (Add cost for point wear) 1.13 1.11 1.06 1.00 0.95 0.96
R15 0.00 ROLLERS, STATIC, TOWED, PNEUMATIC 1.08 1.06 1.03 1.00 0.97 0.96 0.93
R20 0.00 ROLLERS, STATIC, TOWED, STEEL DRUM 1.08 1.06 1.03 1.00 0.97 0.96 0.93
R30 0.00 ROLLERS, STATIC, SELF-PROPELLED
R30 0.01 PNEUMATIC 1.07 1.05 1.03 1.00 0.97 0.96

R30 0.02 SMOOTH DRUM 1.07 1.05 1.03 1.00 0.97 0.96 0.93
R30 0.03 TAMPING FOOT, LANDFILL & SOIL COMPACTORS 1.08 1.06 1.03 1.00 0.97 0.96 0.93 0.87 0.82
R40 0.00 ROLLERS, VIBRATORY, TOWED 1.08 1.06 1.03 1.00 0.97 0.96
R45 0.00 ROLLERS, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM 1.08 1.06 1.03 1.00 0.97 0.96
R50 0.00 ROLLERS, VIBRATORY, SELF-PROPELLED, SINGLE DRUM 1.08 1.06 1.03 1.00 0.97 0.96
R55 0.00 ROOFING EQUIPMENT 1.10 1.08 1.05 1.00 0.96
S10 0.00 SCRAPERS, ELEVATING
S10 0.01 0 THRU 200 HP 1.18 1.16 1.12 1.00 0.95 0.94 0.88
S10 0.02 OVER 200 HP 1.19 1.17 1.12 1.00 0.95 0.93 0.87 0.83 0.81
S15 0.00 SCRAPERS, CONVENTIONAL 1.17 1.16 1.11 1.00 0.95 0.94 0.88 0.84 0.83 0.79 0.75
S20 0.00 SCRAPERS, TANDEM POWERED 1.17 1.16 1.11 1.00 0.95 0.94 0.88 0.84 0.83 0.79 0.75
S25 0.00 SCRAPERS, TRACTOR DRAWN 1.17 1.16 1.12 1.00 0.95 0.94 0.88 0.84 0.83
S30 0.00 SCREENING & CRUSHING PLANTS
S30 0.10 CONVEYORS 1.09 1.08 1.05 1.00 0.97 0.96 0.93
S30 0.20 CRUSHERS - VERTICAL & HORIZONTAL SHAFT IMPACTOR 1.09 1.07 1.04 1.00 0.97 0.96 0.93 0.90 0.88 0.84 0.78 0.76 0.74 0.73 0.73 0.72 0.71 0.70
S30 0.21 CRUSHERS - CONE 1.09 1.07 1.04 1.00 0.97 0.96 0.93 0.90 0.88 0.84 0.78 0.76 0.74 0.73 0.73 0.72 0.71 0.70
3- 18
3-18
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14
4/30/2014
CATEGORY REGION 2
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
S30 0.22 CRUSHERS - JAW 1.09 1.07 1.04 1.00 0.97 0.96 0.93 0.90 0.88 0.84 0.78 0.76 0.74 0.73 0.73 0.72 0.71 0.70
S30 0.30 SCREENING PLANT 1.09 1.08 1.05 1.00 0.97 0.96 0.93
S35 0.00 SNOW REMOVAL EQUIPMENT 1.10 1.09 1.05 1.00 0.96 0.96
S40 0.00 SOIL & ROAD STABILIZERS 1.18 1.16 1.12 1.00 0.95 0.94 0.88
S45 0.00 SPLITTERS, ROCK & CONCRETE 1.10 1.09 1.05 1.00 0.96
T10 0.00 TRACTOR BLADES & ATTACHMENTS (including agricultural) 1.13 1.11 1.06 1.00 0.95 0.96 0.93
T15 0.00 TRACTORS, CRAWLER (DOZER) (includes blade)
T15 0.01 0 THRU 225 HP 1.14 1.12 1.07 1.00 0.95 0.95 0.91
T15 0.02 226 HP THRU 425 HP 1.13 1.11 1.06 1.00 0.95 0.96 0.92 0.88 0.86
T15 0.03 OVER 425 HP 1.12 1.11 1.06 1.00 0.96 0.96 0.93 0.89 0.87 0.83 0.78
T20 0.00 TRACTORS, WHEEL TYPE (DOZER) 1.08 1.06 1.03 1.00 0.97 0.96 0.93 0.88 0.84 0.79
T25 0.00 TRACTORS, AGRICULTURAL
T25 0.10 CRAWLER 1.08 1.06 1.04 1.00 0.97 0.96 0.93
T25 0.20 WHEEL 1.08 1.06 1.04 1.00 0.97 0.96
T30 0.00 TRENCHERS, CHAIN TYPE CUTTER 1.08 1.06 1.03 1.00 0.97 0.96
T35 0.00 TRENCHERS, WHEEL TYPE CUTTER 1.08 1.06 1.03 1.00 0.97 0.96
T40 0.00 TRUCK OPTIONS
T40 0.10 CRANES / HOISTS, PERSONNEL & MATERIAL HANDLING 1.10 1.09 1.05 1.00 0.96 0.96
T40 0.20 DUMP BODY, REAR 1.09 1.08 1.05 1.00 0.97 0.96
T40 0.30 FLATBEDS, WITH SIDES 1.10 1.09 1.05 1.00 0.96 0.96
T40 0.41 HOIST, ELECTRIC DRIVE 1.10 1.09 1.05 1.00 0.96 0.96
T40 0.50 TRANSIT MIXERS 1.10 1.08 1.05 1.00 0.96 0.96
3- 19
3-19
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14
4/30/2014
CATEGORY REGION 2
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
T40 0.60 WATER TANKS 1.11 1.09 1.05 1.00 0.96 0.96
T40 0.70 ALL OTHER OPTIONS 1.10 1.09 1.05 1.00 0.96 0.96
T45 0.00 TRUCK TRAILERS
T45 0.10 BOTTOM DUMP 1.09 1.08 1.05 1.00 0.97 0.96 0.93
T45 0.20 END DUMP 1.09 1.08 1.05 1.00 0.97 0.96 0.93
T45 0.30 PUP TRAILER 1.09 1.08 1.05 1.00 0.97 0.96
T45 0.41 LOWBOY, RIGID NECK, DROP DECK 1.09 1.08 1.05 1.00 0.97 0.96 0.93
T45 0.50 FLATBED TRAILER 1.09 1.08 1.05 1.00 0.97 0.96 0.93
T45 0.60 MISCELLANEOUS / UTILITY 1.09 1.08 1.05 1.00 0.97 0.96 0.93
T45 0.70 WATER TANKER TRAILER 1.11 1.09 1.05 1.00 0.96 0.96 0.92
T45 0.80 DECONTAMINATION FACILITY 1.11 1.09 1.05 1.00 0.96 0.96
T45 0.90 TANK TRAILERS 1.11 1.09 1.05 1.00 0.96 0.96 0.92
T50 0.00 TRUCKS, HIGHWAY (Add attachments as required)
T50 0.01 0 THRU 10,000 GVW 1.13 1.11 1.08 1.00 0.96 0.94
T50 0.02 OVER 10,000 THRU 30,000 GVW (Chassis only - Add options) 1.13 1.11 1.08 1.00 0.96 0.94 0.88
T50 0.03 OVER 30,000 GVW (Chassis only - Add options) 1.13 1.11 1.08 1.00 0.96 0.94 0.88 0.85 0.82
T55 0.00 TRUCKS, OFF-HIGHWAY
T55 0.10 RIGID FRAME 1.05 1.03 1.02 1.00 0.98 0.98 0.96 0.92 0.90 0.85 0.78 0.73 0.72 0.71
T55 0.20 ARTICULATED FRAME 1.05 1.03 1.02 1.00 0.98 0.98 0.96 0.92 0.90
T56 0.00 TRUCKS,OFF-HIGHWAY/PRIME MOVER TRACTORS & WAGONS
T56 0.10 PRIME MOVER TRACTORS 1.05 1.03 1.02 1.00 0.98 0.98 0.96 0.92 0.90 0.85 0.78 0.73 0.72 0.71
T56 0.20 WAGONS, BOTTOM DUMP 1.06 1.04 1.03 1.00 0.98 0.98 0.96 0.92 0.89 0.84 0.77
3- 20
3-20
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14
4/30/2014
CATEGORY REGION 2
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
T56 0.30 WAGONS, REAR DUMP 1.06 1.04 1.03 1.00 0.98 0.98 0.96 0.91 0.89
T57 0.00 TRUCKS, VACUUM 1.10 1.08 1.05 1.00 0.96 0.96 0.92
T60 0.00 TRUCKS, WATER, OFF-HIGHWAY 1.06 1.04 1.03 1.00 0.98 0.98 0.96 0.91 0.89
T65 0.00 TUNNEL/MINING EQUIPMENT
T65 0.10 DRIFTING & TUNNELING DRILLS 1.07 1.05 1.03 1.00 0.96 0.95 0.92 0.86 0.79 0.73
T65 0.20 TUNNEL BORING MACHINES 1.10 1.08 1.05 1.00 0.97 0.96 0.93 0.90 0.87 0.83 0.77 0.74 0.73
T65 0.30 PRODUCTION DRILLING RIGS 1.07 1.05 1.04 1.00 0.96 0.95 0.92 0.86 0.79
T65 0.40 ROADHEADERS & CONTINUOUS MINERS 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.90 0.87 0.83 0.77 0.74
T65 0.50 ROCK BOLTING EQUIPMENT 1.10 1.08 1.05 1.00 0.96 0.96 0.92
T65 0.61 LOADING & HAULING EQUIPMENT, DIESEL OR GAS 1.10 1.08 1.05 1.00 0.96 0.96 0.92 0.89 0.86
T65 0.62 LOADING & HAULING EQUIPMENT, ELECTRIC 1.10 1.08 1.05 1.00 0.96 0.96 0.92 0.89 0.86 0.82
T65 0.63 LOADING & HAULING EQUIPMENT, AIR-POWERED 1.11 1.09 1.05 1.00 0.96 0.96 0.92
T65 0.70 LOCOMOTIVES 1.10 1.08 1.05 1.00 0.96 0.96 0.92 0.89 0.86
T65 0.90 OTHER TUNNELING EQUIPMENT 1.10 1.08 1.05 1.00 0.96 0.96 0.92
W10 0.00 WAGONS, BOTTOM DUMP 1.05 1.03 1.02 1.00 0.98 0.98 0.96 0.92 0.90
W15 0.00 WAGONS, REAR DUMP 1.05 1.03 1.02 1.00 0.98 0.98 0.96 0.92 0.90
W25 0.00 WATER & CO2 BLASTERS
W25 0.10 LOW PRESSURE, (< 5,000 PSI) 1.10 1.09 1.05 1.00
W25 0.20 HIGH PRESSURE, (>= 5,000 PSI) 1.10 1.09 1.05 1.00
W25 0.30 STEAM CLEANERS 1.10 1.09 1.05 1.00
W25 0.40 CO2 BLASTERS 1.10 1.09 1.05 1.00 0.96
W25 0.50 WET ABRASIVE BLASTING SYSTEM (TORBO) 1.13 1.10 1.06 1.00 0.95 0.95 0.91
3- 21
3-21
EP 1110-1-8, Vol. 2
EP 1110-1-8
30 Apr
(Vol. 2) 14
4/30/2014
CATEGORY REGION 2
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
W30 0.00 WATER TANKS
W30 0.10 PORTABLE WITH WHEELS 1.06 1.04 1.03 1.00 0.98 0.98 0.96 0.91 0.89
W30 0.20 SKID MOUNTED 1.06 1.04 1.03 1.00 0.98 0.98 0.96 0.91 0.89
W35 0.00 WELDERS
W35 0.10 ENGINE DRIVEN 1.11 1.09 1.05 1.00 0.96 0.96
W35 0.20 ELECTRIC DRIVEN 1.10 1.09 1.05 1.00 0.96
3- 22
3-22
EP 1110-1-8, Vol. 2
30 Apr 14
TOTAL HOURLY RATE CALCULATION FOR OVERAGE EQUIPMENT
EXAMPLE
Assume the following set of given information for the rate calculation example:
1. The unit of equipment is not listed in table 2-1.
2. The equipment is contractor owned.
3. Data for the unit in question:
a. Caterpillar front-end wheel loader

b. Model 950-G, 4WD, 3.5 CY capacity
c. Serial number indicates year of manufacture = 2002
d. Actual purchase price in 2002 = $205,000
(includes all regional discounts, sales tax and freight)
e. Horsepower is 180 hp (fuel is Diesel off-road)
f. Drive tire (DT) size = 23.50 x 25, 16 ply, L-3 (appendix F tire code ANNB5)
DT cost (2014) = 4 tires x $4,233 /tire = $16,932
g. Weight = 392 cwt
4. Table 3-1, Age Adjustment Factors for Ownership Costs:
a. The category L40, subcategory 0.11 (wheel loaders < 225 hp)
b. The year corresponding to the last age adjustment factor = 2008
5. Adjust the actual purchase price:
a. Economic Indexes from appendix E (wheel loaders EK = 45)

(1) For 2008 (first year of economic life), the economic index = 6695
(2) For 2002 (year of manufacture), the economic index = 5612
b. Purchase price [total equipment value (TEV)] indexed to 2008 (first year of economic
life): (Purchase price includes discount, sales tax, and freight for this region).
(6695 / 5612) x $205,000 = $244,561 (= 2008 purchase price)
6. Hourly rate is computed as follows in accordance with figure 2-1, Equipment Rate
Computation Worksheet.
Figure 3-1. Total Hourly Rate Calculation for Overage Equipment
3-23
EP 1110-1-8, Vol. 2
30 Apr 14
Example: The piece of equipment shown in this example is based on a known piece of
equipment for illustration purposes only.
USE THIS WORKSHEET TO COMPUTE A HOURLY RATE FOR EQUIPMENT THAT IS NOT IN THIS PAMPHLET OR IS IN
THE PAMPHLET BUT NOT EQUIVALENT IN SIZE, CAPACITY, HORSEPOWER OR VALUE. (See Appendix A for a blank
form)
Region 02
ID No:
(1) Equipment Description: Loader, Front-end, Wheel, 4WD, 3.5 CY capacity
(2) Model and Series: Caterpillar Model 950-G
(4) Year Manufactured: 2002 indexed to 2008
6-marine diesel 3
6-marine diesel 0
from 0 to 6 ==> None
(8) Shipping Weight (cwt): 392 cwt
(9) Tire size and number of tires: (Cost of tires based on present year - see 1.a.(3) and Appendix F)
(a) Front (FT): 0 $0 $0
(b) Drive (DT): 23.5X25/16Ply ANNB5 4 $4,233 $16,932
[at Year (yr) of Manufacture] $0 OR actual purchase price: $244,561

b. Category and Subcategory Number: L40 0.11
Figure 3-1. Total Hourly Rate Calculation for Overage Equipment Page 1 of 6
3-24
EP 1110-1-8, Vol. 2
30 Apr 14
Region 02
2. EQUIPMENT VALUE
a. List Price + Accessories: [at Year (yr) of Manufacture] = $0
(1) Discount: (List Price + Accessories) x Discount

{1.a.(10)} {1.c.(3)}
($0 + $0.00) x 0.075 = - [ $0 ]
(2) Subtotal {2.a}. - {2.a.(1)} Subtotal = $0
(3) Sales or Import Subtotal x Tax Rate

$0 x 6.00% = $0
(4) Total Discounted Price: Subtotal: {2.a.(2)} + {2.a.(3)} Subtotal = $0
Freight Rate
b. Freight: Shipping Weight x per cwt
0,000 cwt x $0.00 /cwt = $0
c. TOTAL EQUIPMENT VALUE (TEV): TOTAL[2.]: = $244,561

a. LIFE / Working Hours

Per Year (WHPY) = N
9,250 hr / 1,450 hr/yr = 6.38 yrs (N)
4. OWNERSHIP COST
a. Depreciation
Tire Index, Year of Present Year or
Manufacture, Year of Use,
{1.a.(4)} / {1.a.(3)} = TCI
3267 / 4050 = 0.807

{2.c.} {1.c.(5)} {4.a.(1)} {1.a.(9)(d)} {1.c.(4)}
[$244,561 x (1.0-0.25) - ( 0.807 x $16,932 )] / 9,250 hr = $18.35 /hr
3-25
EP 1110-1-8, Vol. 2
30 Apr 14
Region 02

Avg Value
(1) [( N - 1.0 ) x (1.0 + SLV) + 2.0] / (2.0 x N) = Factor
{3.a.} {1.c.5.} {3.a.} {AVF}
[(6.38 yr - 1.0) x (1.0 + 0.25) + 2.0] / (2.0 x 6.38 yr) = 0.684
Adjusted
$244,561 x 0.684 x 1.70% / 1,450 hr/yr = $1.96 /hr

{4.a.(2)} + {4.b.(2)}
5. OPERATING COST
a. Fuel Costs:
(1) Equipment:
Fuel Cost per

Fuel Factor x Horsepower (hp) x Gallon (gal)
{1.c.(6)} {1.a.(5)} {Appendix B}
0.031 x 180 hp x $3.49 /gal = $19.47 /hr
(2) Carrier:
Fuel Factor x hp x Fuel Cost per gal

{1.c.(7)} {1.a.(6)} {Appendix B}
0.000 x 0 hp x $0.00 /gal = $0.00 /hr

{(5.a (1)} + {5.a (2)}
b. FOG Cost:
(1) Equipment:
Equipment Hourly Labor Adjustment

FOG Factor x Fuel Cost x Factor (LAF)
{1.c.(8)} {5.a.(1)} {Appendix B}
0.111 x $19.47 /hr x 1.02 = $2.20 /hr
3-26
EP 1110-1-8, Vol. 2
30 Apr 14
Region 02
(2) Carrier:
Carrier Hourly
{1.c.(8)} {5.a.(2)} {Appendix B}
0.111 x $0.00 /hr x 1.02 = $0.00 /hr

{5.b.(1)} + {5.b.(2)}

d. Repair Cost:

[EK is from 1c. (1)]
Economic Index, / Economic Index, Year

Present Year or Year of Manufacture, 1.a.(4)
of Use,1.a.(3) = EAF
Appendix E, EK={1.c.(1)} Appendix E, EK={1.c.(1)}
7830 / 6695 = 1.170
RCF x EAF x LAF = RF

{1.c.(10)} {5.d.(1)} {Appendix B}
0.70 x 1.170 x 1.02 = 0.835
(3) Repair Cost:

{2.c.} {4.a.(1)} {1.a.(9)(d)} {5.d.(2)} {1.c.(4)}
[$244,561 - (0.807 x $16,932)] x 0.835 / 9,250
3-27
EP 1110-1-8, Vol. 2
30 Apr 14
Region 02

{1.a.(9)(a)} {1.c.(9)(a)} {Appendix F}
(1.5 x $0) / (1.8 x 0.83 x 0 hr) = $0.00 /hr

{1.a.(9)(b)} {1.c.(9)(b)} {Appendix F}
(1.5 x $16,932) / (1.8 x 0.54 x 3200 hr) = $8.17 /hr

{1.a.(9)(c)} {1.c.(9)(c)} {Appendix F}
(1.5 x $0) / (1.8 x 0.92 x 0 hr) = $0.00 /hr
(4) Total Tire Wear Cost: Total [5.e.] = $8.17 /hr

Sum {5.e.(1)} through {5.e.(3)}

$8.17 /hr x (0.15 x 1.02) Total [5.f.] = $1.25 /hr
g. TOTAL HOURLY OPERATING COST: Total [5.] = $51.93 /hr

Sum {5.a.} through {5.f.}
3-28
EP 1110-1-8, Vol. 2
30 Apr 14
Region 02
6. HOURLY RATES

{4.c.} {5.g.}
$20.31 /hr + $51.93 /hr = $72.24 /hr
Depreciation + (FCCM x 40 hr/wk / Work hr/wk) + Operating Cost
{4.a.(2)} {4.b.(2)} example:60 hr/wk {5.g.}
$0.00 /hr + ($0.00 /hr x 40 hr/wk / 60 hr/wk) + $0.00 /hr = $0.00 /hr
(example:60 hr/wk)

{4.a.(2)} {4.b.(2)}
($0.00 /hr x 0.50) + $0.00 /hr = $0.00 /hr
See Figure 3-2 for standby calculations for overage equipment
3-29
EP 1110-1-8, Vol. 2
30 Apr 14
Table 3-2. Equipment Age Adjustment Factors
for
Standby costs
The factors in this table are used when the age of a unit of equipment is other than the
age of the equipment listed in table 2-1.
These factors are multiplied by the hourly standby costs shown in table 2-1 and result in
a standby rate adjusted for the actual age of the equipment being considered.
When the actual “life” in hours of the unit of equipment has exceeded the economic life
given in appendix D, the age will be determined as discussed in chapter 3.
Refer to chapter 3, as follows:
3.13. Rate Adjustments Overage Equipment Standby
3-31
3-30
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
Table 3-2 Equipment Age Adjustment Factors for Standby Cost
REGION 2 Life in Years Year Purchased New
CATEGORY
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
A10 0.00 AGGREGATE / CHIP SPREADERS
A10 0.10 SELF-PROPELLED 1.08 1.05 1.03 1.00 0.97 0.97 0.93 0.89 0.86 0.82 0.76 0.77 0.77 0.77 0.75 0.73 0.72 0.69
A10 0.20 TOWED & TAILGATE 1.08 1.05 1.03 1.00 0.97 0.97 0.93 0.89 0.86 0.81 0.76 0.76 0.76 0.76 0.75 0.73 0.72 0.69
A15 0.00 AIR COMPRESSORS, PORTABLE
A15 0.10 ROTARY SCREW 1.11 1.09 1.04 1.00 0.91 0.91 0.85 0.79 0.76 0.72 0.69 0.69 0.68 0.69 0.67 0.69 0.69 0.68
A15 0.20 SHOP TYPE 1.10 1.09 1.04 1.00 0.92 0.91 0.86 0.80 0.77 0.74 0.71 0.70 0.70 0.71 0.69 0.71 0.70 0.70
A20 0.00 AIR HOSE, TOOLS & EQUIPMENT
A20 0.10 AIR DRILL HOSE 1.09 1.08 1.03 1.00 0.93 0.92 0.87 0.82 0.79 0.76 0.73 0.73 0.73 0.73 0.72 0.73 0.73 0.73
A20 0.20 SANDBLAST HOSE 1.09 1.08 1.03 1.00 0.93 0.92 0.87 0.82 0.79 0.76 0.73 0.73 0.73 0.73 0.72 0.73 0.73 0.73
A20 0.30 SANDBLASTERS, BREAKERS, & MISC. AIR TOOLS 1.10 1.08 1.04 1.00 0.92 0.92 0.87 0.81 0.78 0.75 0.72 0.71 0.71 0.72 0.70 0.72 0.71 0.71
A25 0.00 ASPHALT PAVING DISTRIBUTORS 1.07 1.05 1.03 1.00 0.97 0.97 0.94 0.90 0.87 0.83 0.79 0.79 0.79 0.79 0.78 0.76 0.75 0.72
A30 0.00 ASPHALT PAVERS & MISCELLANEOUS ROAD EQUIPMENT
A30 0.10 SELF PROPELLED 1.07 1.05 1.03 1.00 0.97 0.97 0.93 0.89 0.87 0.82 0.78 0.78 0.78 0.78 0.77 0.75 0.73 0.71
A30 0.20 TOWED 1.08 1.05 1.03 1.00 0.97 0.97 0.93 0.89 0.86 0.82 0.77 0.77 0.77 0.77 0.76 0.74 0.72 0.70
A30 0.30 SLURRY SEAL PAVERS (Cold mix) 1.08 1.05 1.03 1.00 0.97 0.97 0.93 0.89 0.86 0.82 0.77 0.77 0.77 0.77 0.76 0.74 0.73 0.70
A30 0.40 MISCELLANEOUS ROAD EQUIPMENT 1.08 1.05 1.03 1.00 0.97 0.97 0.93 0.89 0.86 0.82 0.77 0.77 0.77 0.77 0.76 0.74 0.72 0.70
A35 0.00 ASPHALT PAVING KETTLES 1.08 1.05 1.03 1.00 0.97 0.97 0.93 0.89 0.86 0.81 0.76 0.76 0.76 0.76 0.75 0.73 0.72 0.69
A40 0.00 ASPHALT & CONCRETE MILLERS / PROFILERS / PLANERS / ROTARY 1.08 1.05 1.03 1.00 0.97 0.97 0.93 0.89 0.86 0.81 0.76 0.76 0.76 0.76 0.75 0.73 0.72 0.69
GRINDERS
A45 0.00 ASPHALT RECYCLERS & SEALERS 1.08 1.05 1.03 1.00 0.97 0.97 0.93 0.89 0.86 0.81 0.76 0.76 0.76 0.76 0.75 0.73 0.72 0.69
B10 0.00 BATCH PLANTS, ASPHALT & CONCRETE
B10 0.10 ASPHALT 1.08 1.05 1.03 1.00 0.97 0.97 0.93 0.89 0.86 0.82 0.76 0.77 0.77 0.77 0.75 0.73 0.72 0.69
B10 0.20 CONCRETE 1.08 1.05 1.03 1.00 0.97 0.97 0.93 0.89 0.86 0.82 0.76 0.77 0.77 0.77 0.75 0.73 0.72 0.69
3- 28
3-31
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
CATEGORY
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
B10 0.30 PUGMILL 1.08 1.05 1.03 1.00 0.97 0.97 0.93 0.89 0.86 0.82 0.77 0.77 0.77 0.77 0.76 0.74 0.72 0.70
B15 0.00 BROOMS, STREET SWEEPERS & FLUSHERS 1.09 1.07 1.04 1.00 0.97 0.96 0.93 0.90 0.88 0.84 0.78 0.75 0.74 0.73 0.73 0.72 0.71 0.69
B20 0.00 BRUSH CHIPPERS 1.09 1.07 1.04 1.00 0.97 0.96 0.93 0.90 0.88 0.84 0.78 0.75 0.74 0.73 0.73 0.72 0.71 0.69
B25 0.00 BUCKETS, CLAMSHELL 1.05 1.04 1.01 1.00 0.97 0.97 0.95 0.94 0.92 0.87 0.82 0.80 0.77 0.72 0.73 0.74 0.73 0.73
B30 0.00 BUCKETS, CONCRETE
B30 0.10 GENERAL PURPOSE, MANUAL TRIP 1.05 1.04 1.01 1.00 0.97 0.97 0.95 0.94 0.93 0.88 0.83 0.81 0.78 0.73 0.74 0.75 0.75 0.74
B30 0.20 LAYDOWN 1.05 1.04 1.01 1.00 0.97 0.97 0.95 0.94 0.93 0.88 0.83 0.81 0.78 0.73 0.74 0.75 0.75 0.74
B30 0.30 LOWBOY 1.05 1.04 1.01 1.00 0.97 0.97 0.95 0.94 0.93 0.88 0.83 0.81 0.78 0.73 0.74 0.75 0.75 0.74
B30 0.40 LOW SLUMP 1.05 1.04 1.01 1.00 0.97 0.97 0.95 0.94 0.93 0.88 0.83 0.81 0.78 0.73 0.74 0.75 0.75 0.74
B35 0.00 BUCKETS, DRAGLINE
B35 0.10 LIGHT WEIGHT 1.05 1.04 1.01 1.00 0.97 0.97 0.95 0.94 0.92 0.87 0.82 0.80 0.77 0.72 0.73 0.74 0.73 0.73
B35 0.20 MEDIUM WEIGHT 1.05 1.04 1.01 1.00 0.97 0.97 0.95 0.94 0.92 0.87 0.82 0.80 0.77 0.72 0.73 0.74 0.74 0.73
B35 0.30 HEAVY WEIGHT 1.05 1.04 1.01 1.00 0.97 0.97 0.95 0.94 0.92 0.87 0.82 0.80 0.77 0.72 0.73 0.74 0.74 0.73
C05 0.00 CHAIN SAWS 1.09 1.08 1.05 1.00 0.97 0.96 0.93 0.90 0.88 0.83 0.78 0.75 0.74 0.73 0.72 0.72 0.70 0.69
C10 0.00 COMPACTORS, WALK-BEHIND OR REMOTE CONTROLLER
C10 0.10 COMPACTORS, RAMMERS / TAMPERS & VIBRATORY PLATES 1.09 1.07 1.04 1.00 0.97 0.97 0.94 0.91 0.88 0.84 0.79 0.76 0.75 0.74 0.74 0.73 0.72 0.71
C10 0.20 ROLLERS, VIBRATORY 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.87 0.83 0.77 0.74 0.72 0.71 0.71 0.70 0.69 0.67
C15 0.00 CONCRETE CLEANERS / ABRASIVE BLASTERS
C15 0.10 WALK BEHIND 1.10 1.09 1.05 1.00 0.96 0.96 0.92 0.89 0.86 0.81 0.75 0.72 0.70 0.69 0.69 0.68 0.67 0.65
C15 0.20 TRUCK/TRAILER MOUNTED 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.86 0.82 0.76 0.73 0.71 0.70 0.70 0.69 0.67 0.66
C20 0.00 CONCRETE BUGGIES 1.10 1.09 1.05 1.00 0.96 0.96 0.92 0.89 0.86 0.81 0.75 0.72 0.70 0.69 0.69 0.68 0.67 0.65
C25 0.00 CONCRETE FINISHERS/SCREEDS/SPREADERS
3- 29
3-32
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
CATEGORY
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
C25 0.10 FINISHERS/TROWELS 1.10 1.08 1.05 1.00 0.96 0.96 0.92 0.89 0.86 0.82 0.75 0.72 0.71 0.69 0.69 0.68 0.67 0.65
C25 0.20 VIBRATORY SCREED 1.10 1.08 1.05 1.00 0.96 0.96 0.92 0.89 0.86 0.82 0.75 0.72 0.71 0.69 0.69 0.68 0.67 0.65
C25 0.25 VIBRATORY LASER SCREED 1.11 1.09 1.06 1.00 0.96 0.96 0.92 0.87 0.85 0.80 0.73 0.69 0.67 0.66 0.66 0.65 0.63 0.61
C25 0.30 MATERIAL/TOPPING SPREADERS 1.11 1.09 1.06 1.00 0.96 0.96 0.92 0.87 0.85 0.80 0.73 0.69 0.67 0.66 0.66 0.65 0.63 0.61
C30 0.00 CONCRETE GRINDERS 1.10 1.08 1.05 1.00 0.96 0.96 0.92 0.89 0.86 0.82 0.75 0.72 0.71 0.69 0.69 0.68 0.67 0.65
C35 0.00 CONCRETE GUNITERS / SHOTCRETERS 1.11 1.09 1.05 1.00 0.96 0.96 0.92 0.88 0.85 0.81 0.74 0.71 0.69 0.68 0.68 0.67 0.65 0.63
C40 0.00 CONCRETE MIXING UNITS 1.10 1.08 1.05 1.00 0.96 0.96 0.92 0.89 0.86 0.82 0.75 0.72 0.71 0.69 0.69 0.68 0.67 0.65
C45 0.00 CONCRETE PAVING MACHINES 1.08 1.05 1.03 1.00 0.97 0.97 0.93 0.89 0.86 0.81 0.76 0.76 0.76 0.76 0.75 0.73 0.72 0.69
C55 0.00 CONCRETE PUMPS 1.09 1.07 1.04 1.00 0.97 0.96 0.93 0.90 0.88 0.84 0.78 0.75 0.74 0.73 0.73 0.72 0.71 0.69
C60 0.00 CONCRETE SAWS (Add cost for sawblade wear) 1.09 1.08 1.05 1.00 0.97 0.96 0.93 0.90 0.88 0.84 0.78 0.75 0.74 0.73 0.73 0.72 0.71 0.69
C65 0.00 CONCRETE VIBRATORS 1.10 1.08 1.04 1.00 0.92 0.92 0.87 0.81 0.78 0.75 0.72 0.71 0.71 0.71 0.70 0.71 0.71 0.71
C70 0.00 CRANES, GANTRY & STRADDLE
C75 0.00 CRANES, HYDRAULIC, SELF-PROPELLED 1.05 1.04 1.01 1.00 0.97 0.97 0.94 0.93 0.92 0.87 0.81 0.79 0.77 0.71 0.72 0.72 0.71 0.69
C80 0.00 CRANES, HYDRAULIC, TRUCK MOUNTED
C80 0.01 UNDER 26 TON 1.05 1.04 1.01 1.00 0.97 0.97 0.94 0.93 0.92 0.87 0.81 0.79 0.77 0.71 0.72 0.72 0.71 0.69
C80 0.02 26 TON THRU 65 TON 1.05 1.04 1.01 1.00 0.97 0.97 0.94 0.93 0.92 0.87 0.81 0.79 0.77 0.71 0.72 0.72 0.71 0.69
C80 0.03 66 TON THRU 125 TON 1.05 1.04 1.01 1.00 0.97 0.97 0.94 0.93 0.92 0.87 0.81 0.79 0.77 0.71 0.73 0.72 0.71 0.70
C80 0.04 OVER 125 TON 1.05 1.04 1.01 1.00 0.97 0.97 0.95 0.94 0.92 0.87 0.82 0.79 0.77 0.72 0.73 0.72 0.71 0.70
C85 0.00 CRANES, MECHANICAL, LATTICE BOOM, CRAWLER MOUNTED
C85 0.11 DRAGLINE, CLAMSHELL, 0 THRU 1.0 CY 1.06 1.04 1.02 1.00 0.96 0.97 0.94 0.93 0.92 0.86 0.80 0.78 0.76 0.70 0.71 0.71 0.70 0.68
C85 0.12 DRAGLINE, CLAMSHELL, OVER 1.0 CY THRU 2.5 CY 1.06 1.04 1.02 1.00 0.96 0.97 0.94 0.93 0.92 0.86 0.81 0.78 0.76 0.70 0.71 0.71 0.70 0.68
C85 0.13 DRAGLINE, CLAMSHELL, OVER 2.5 CY THRU 5.0 CY 1.06 1.04 1.02 1.00 0.97 0.97 0.94 0.93 0.92 0.86 0.81 0.78 0.76 0.70 0.71 0.71 0.70 0.68
3- 30
3-33
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
CATEGORY
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
C85 0.14 DRAGLINE, CLAMSHELL, OVER 5.0 CY 1.06 1.04 1.02 1.00 0.97 0.97 0.94 0.93 0.92 0.86 0.81 0.79 0.76 0.70 0.72 0.71 0.70 0.68
C85 0.21 LIFTING, 0 THRU 25 TON 1.06 1.04 1.02 1.00 0.96 0.97 0.94 0.93 0.92 0.86 0.81 0.78 0.76 0.70 0.71 0.71 0.70 0.68
C85 0.22 LIFTING, 26 TON THRU 50 TON 1.06 1.04 1.02 1.00 0.97 0.97 0.94 0.93 0.92 0.86 0.81 0.78 0.76 0.70 0.71 0.71 0.70 0.68
C85 0.23 LIFTING, 51 TON THRU 150 TON 1.05 1.04 1.01 1.00 0.97 0.97 0.95 0.94 0.92 0.87 0.82 0.79 0.77 0.72 0.73 0.72 0.71 0.70
C85 0.24 LIFTING, OVER 150 TON 1.05 1.04 1.01 1.00 0.97 0.97 0.95 0.94 0.92 0.87 0.82 0.79 0.77 0.72 0.73 0.73 0.72 0.70
C90 0.00 CRANES, MECHANICAL, LATTICE BOOM, TRUCK MOUNTED
C90 0.01 UNDER 26 TON 1.05 1.04 1.01 1.00 0.97 0.97 0.94 0.93 0.92 0.87 0.81 0.79 0.77 0.71 0.72 0.72 0.71 0.69
C90 0.02 26 TON THRU 65 TON 1.05 1.04 1.01 1.00 0.97 0.97 0.94 0.93 0.92 0.87 0.81 0.79 0.77 0.71 0.72 0.72 0.71 0.69
C90 0.03 66 TON THRU 125 TON 1.06 1.04 1.02 1.00 0.97 0.97 0.94 0.93 0.92 0.86 0.81 0.78 0.76 0.70 0.71 0.71 0.70 0.68
C90 0.04 OVER 125 TON 1.06 1.04 1.02 1.00 0.97 0.97 0.94 0.93 0.92 0.86 0.81 0.79 0.76 0.70 0.72 0.71 0.70 0.68
C95 0.00 CRANES, TOWER 1.06 1.04 1.02 1.00 0.97 0.97 0.94 0.93 0.92 0.86 0.81 0.78 0.76 0.70 0.71 0.71 0.70 0.68
D10 0.00 DRILLS, AIR/HYDRAULIC,CRWLR MTD,0" THRU 6.5" DIA HOLE (Add cost for
D10 0.10 DRILLS, AIR TRACK (Add cost for drill steel and bit wear) 1.07 1.05 1.04 1.00 0.96 0.95 0.92 0.85 0.78 0.71 0.65 0.60 0.58 0.52 0.50 0.49 0.48 0.47
D10 0.20 DRILLS, HYDRAULIC TRACK (Add cost for drill steel and bit wear) 1.08 1.05 1.04 1.00 0.96 0.94 0.91 0.84 0.77 0.70 0.64 0.59 0.57 0.51 0.49 0.48 0.47 0.46
D15 0.00 DRILLS, HORIZONTAL
D15 0.10 DRILLS, HORIZONTAL BORING & GROUND PIERCING (Add cost for drill steel 1.08 1.05 1.04 1.00 0.96 0.94 0.91 0.84 0.77 0.70 0.64 0.59 0.57 0.51 0.49 0.48 0.47 0.46
and bit wear)
D15 0.20 DRILLS, HORIZONTAL & DIRECTIONAL (Add cost for drill steel and bit wear) 1.08 1.05 1.04 1.00 0.96 0.94 0.91 0.84 0.77 0.70 0.64 0.59 0.57 0.51 0.49 0.48 0.47 0.46
D20 0.00 DRILLS, CORE, COLUMN MOUNTED (Add cost for drill steel and bit wear) 1.08 1.06 1.04 1.00 0.95 0.94 0.91 0.84 0.77 0.70 0.63 0.58 0.56 0.50 0.48 0.47 0.46 0.45
D25 0.00 DRILLS, CORE & DOWELLING (Add cost for drill steel and bit wear) 1.08 1.05 1.04 1.00 0.96 0.94 0.91 0.84 0.77 0.70 0.64 0.59 0.57 0.51 0.49 0.48 0.47 0.46
D30 0.00 DRILLS, EARTH / AUGER (Add cost for drill steel and cutting edge wear) 1.08 1.05 1.04 1.00 0.96 0.94 0.91 0.84 0.77 0.70 0.64 0.59 0.57 0.51 0.49 0.48 0.47 0.46
D35 0.00 DRILLS, ROTARY BLASTHOLE (Add cost for drill steel and bit wear)
D35 0.11 DIESEL, 4.5" THRU 9.875" DIAMETER HOLE (Add cost for drill steel and bit 1.07 1.05 1.04 1.00 0.96 0.95 0.92 0.86 0.79 0.72 0.66 0.61 0.60 0.54 0.53 0.52 0.51 0.50
wear)
3- 31
3-34
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
CATEGORY
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
D35 0.12 DIESEL, OVER 9.875" DIAMETER (Add cost for drill steel and bit wear) 1.07 1.05 1.04 1.00 0.96 0.95 0.92 0.86 0.79 0.73 0.67 0.62 0.61 0.55 0.54 0.53 0.51 0.50
D35 0.21 ELECTRIC, 4.5" THRU 9.875" DIAMETER HOLE (Add cost for drill steel and 1.07 1.05 1.04 1.00 0.96 0.95 0.92 0.86 0.79 0.72 0.66 0.61 0.60 0.54 0.53 0.52 0.51 0.50
bit wear)
D35 0.22 ELECTRIC, OVER 9.875" DIAMETER (Add cost for drill steel and bit wear) 1.07 1.05 1.04 1.00 0.96 0.95 0.92 0.86 0.79 0.73 0.67 0.62 0.61 0.55 0.54 0.53 0.51 0.50
F10 0.00 FORK LIFTS 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.86 0.82 0.76 0.73 0.71 0.70 0.70 0.69 0.68 0.66
G10 0.00 GENERATOR SETS
G10 0.10 PORTABLE 1.05 1.03 1.02 1.00 0.94 0.92 0.89 0.84 0.80 0.76 0.72 0.70 0.70 0.70 0.70 0.69 0.69 0.69
G10 0.20 SKID MOUNTED 1.05 1.03 1.02 1.00 0.94 0.92 0.89 0.84 0.80 0.76 0.72 0.70 0.70 0.70 0.70 0.70 0.70 0.69
G15 0.00 GRADERS, MOTOR 1.18 1.16 1.12 1.00 0.95 0.94 0.88 0.84 0.82 0.79 0.74 0.71 0.70 0.69 0.69 0.67 0.64 0.62
H10 0.00 HAMMERS, HYDRAULIC (Demolition tool) (Add cost for point wear) 1.10 1.08 1.05 1.00 0.96 0.96 0.92 0.89 0.86 0.82 0.75 0.72 0.71 0.70 0.69 0.68 0.67 0.65
H13 0.00 HAZARDOUS/TOXIC WASTE EQUIPMENT
H13 0.11 COMPACTORS (Compression force) 0 THRU 50 TONS 1.09 1.08 1.05 1.00 0.97 0.96 0.93 0.90 0.87 0.83 0.77 0.74 0.73 0.72 0.72 0.71 0.69 0.68
H13 0.12 COMPACTORS (Compression force) OVER 50 TONS 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.87 0.82 0.76 0.73 0.72 0.71 0.70 0.69 0.68 0.66
H13 0.21 FILTER PRESSES, STATIONARY 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.86 0.82 0.76 0.73 0.71 0.70 0.70 0.69 0.68 0.66
H13 0.22 FILTER PRESSES, MOBILE 1.09 1.08 1.05 1.00 0.97 0.96 0.93 0.90 0.87 0.83 0.77 0.74 0.73 0.72 0.72 0.71 0.69 0.68
H13 0.30 CENTRIFUGES 1.10 1.09 1.05 1.00 0.96 0.96 0.92 0.89 0.86 0.81 0.75 0.72 0.70 0.69 0.69 0.68 0.67 0.65
H13 0.40 SHREDDERS 1.09 1.08 1.05 1.00 0.97 0.96 0.93 0.90 0.87 0.83 0.77 0.74 0.73 0.72 0.72 0.71 0.69 0.68
H13 0.51 SOIL TREATMENT PLANT, MOBILE 1.09 1.08 1.05 1.00 0.97 0.96 0.93 0.90 0.87 0.83 0.77 0.74 0.73 0.72 0.72 0.71 0.69 0.68
H13 0.61 SLUDGE PROCESSING EQUIP, SLUDGE DISPENSERS 1.09 1.08 1.05 1.00 0.97 0.96 0.93 0.90 0.87 0.83 0.77 0.74 0.73 0.72 0.72 0.71 0.69 0.68
H13 0.71 WASTE HANDLING EQUIPMENT, DRUM HANDLING 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.87 0.83 0.77 0.74 0.72 0.71 0.71 0.70 0.69 0.67
H15 0.00 HEATERS, SPACE
H20 0.00 HOISTS & AIR WINCHES 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.86 0.82 0.76 0.73 0.71 0.70 0.70 0.69 0.68 0.66
H25 0.00 HYDRAULIC EXCAVATORS, CRAWLER MOUNTED
3- 32
3-35
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
CATEGORY
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
H25 0.10 0 LBS THRU 12,500 LBS (COMPACT EXCAVATORS) 1.06 1.04 1.02 1.00 0.96 0.97 0.94 0.92 0.91 0.85 0.79 0.76 0.73 0.67 0.68 0.68 0.67 0.65
H25 0.11 OVER 12,500 LBS THRU 40,000 LBS 1.06 1.04 1.02 1.00 0.96 0.97 0.94 0.92 0.91 0.85 0.79 0.76 0.73 0.67 0.68 0.68 0.67 0.65
H25 0.14 OVER 160,000 LBS 1.06 1.04 1.02 1.00 0.96 0.97 0.94 0.93 0.92 0.86 0.80 0.78 0.75 0.69 0.70 0.70 0.69 0.67
H25 0.21 ATTACHMENTS, MOBILE SHEARS 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.87 0.83 0.77 0.74 0.73 0.71 0.71 0.70 0.69 0.67
H25 0.22 ATTACHMENTS, MATERIAL HANDLING 1.10 1.08 1.05 1.00 0.96 0.96 0.92 0.89 0.86 0.82 0.75 0.72 0.71 0.70 0.69 0.68 0.67 0.65
H25 0.23 ATTACHMENTS, CONCRETE PULVERIZERS 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.87 0.83 0.77 0.74 0.73 0.71 0.71 0.70 0.69 0.67
H25 0.24 ATTACHMENTS, COMPACTORS 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.87 0.83 0.77 0.74 0.73 0.71 0.71 0.70 0.69 0.67
H30 0.00 HYDRAULIC EXCAVATORS, WHEEL MOUNTED
H30 0.01 0 THRU 1.0 CY 1.06 1.04 1.02 1.00 0.96 0.97 0.94 0.92 0.91 0.85 0.79 0.76 0.73 0.67 0.68 0.68 0.67 0.65
H30 0.02 OVER 1.0 CY 1.06 1.04 1.02 1.00 0.96 0.97 0.94 0.93 0.91 0.85 0.79 0.76 0.74 0.67 0.69 0.68 0.67 0.65
H35 0.00 HYDRAULIC SHOVELS, CRAWLER MOUNTED
H35 0.11 DIESEL, 0 CY THRU 5.0 CY 1.06 1.04 1.02 1.00 0.96 0.97 0.94 0.93 0.92 0.86 0.80 0.78 0.76 0.70 0.71 0.71 0.70 0.68
H35 0.12 DIESEL, OVER 5.0 CY 1.06 1.04 1.02 1.00 0.96 0.97 0.94 0.93 0.92 0.86 0.81 0.78 0.76 0.70 0.71 0.71 0.70 0.68
H35 0.21 ELECTRIC, OVER 2.5 CY 1.06 1.04 1.02 1.00 0.97 0.97 0.94 0.93 0.92 0.86 0.81 0.78 0.76 0.70 0.71 0.71 0.70 0.68
L10 0.00 LAND CLEARING EQUIPMENT 1.12 1.11 1.06 1.00 0.96 0.96 0.93 0.89 0.87 0.83 0.78 0.76 0.74 0.74 0.73 0.72 0.70 0.68
L15 0.00 LANDSCAPING EQUIPMENT 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.87 0.83 0.77 0.74 0.72 0.71 0.71 0.70 0.69 0.67
L20 0.00 LIGHTING SETS, TRAILER MOUNTED
L20 0.10 METALLIC VAPOR 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.86 0.82 0.76 0.73 0.71 0.70 0.70 0.69 0.67 0.66
L25 0.00 LINE STRIPING EQUIPMENT 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.86 0.82 0.76 0.73 0.71 0.70 0.70 0.69 0.67 0.66
L30 0.00 LOADERS, BELT (Conveyor belts) & ACCESSORIES 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.86 0.82 0.76 0.73 0.71 0.70 0.70 0.69 0.68 0.66
3- 33
3-36
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
CATEGORY
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
L35 0.00 LOADERS, FRONT END, CRAWLER TYPE 1.12 1.11 1.06 1.00 0.96 0.96 0.93 0.89 0.87 0.83 0.78 0.76 0.74 0.74 0.73 0.72 0.70 0.68
L40 0.00 LOADERS, FRONT END, WHEEL TYPE
L40 0.11 ARTICULATED, 0 THRU 225 HP 1.13 1.11 1.06 1.00 0.95 0.96 0.92 0.89 0.86 0.82 0.77 0.74 0.72 0.72 0.72 0.71 0.69 0.67
L40 0.12 ARTICULATED, OVER 225 HP 1.12 1.10 1.06 1.00 0.96 0.96 0.93 0.89 0.87 0.83 0.79 0.76 0.75 0.74 0.74 0.73 0.71 0.69
L40 0.20 SKID STEER 1.12 1.11 1.06 1.00 0.96 0.96 0.93 0.89 0.87 0.83 0.78 0.75 0.74 0.74 0.73 0.72 0.70 0.69
L40 0.21 SKID STEER ATTACHMENTS 1.13 1.11 1.06 1.00 0.95 0.96 0.92 0.89 0.87 0.83 0.78 0.75 0.73 0.73 0.72 0.71 0.70 0.68
L40 0.31 TOOL CARRIER & TELESCOPIC HANDLERS, 0 THRU 225 HP 1.13 1.11 1.06 1.00 0.95 0.96 0.92 0.89 0.86 0.82 0.77 0.74 0.73 0.72 0.72 0.71 0.69 0.67
L40 0.32 TOOL CARRIER & TELESCOPIC HANDLERS, OVER 225 HP 1.11 1.10 1.06 1.00 0.96 0.96 0.93 0.90 0.88 0.84 0.80 0.77 0.76 0.75 0.75 0.74 0.72 0.71
L45 0.00 LOADERS / BACKHOE, CRAWLER TYPE 1.12 1.11 1.06 1.00 0.96 0.96 0.93 0.89 0.87 0.83 0.78 0.75 0.74 0.74 0.73 0.72 0.69 0.68
L50 0.00 LOADERS / BACKHOE, WHEEL TYPE 1.13 1.11 1.06 1.00 0.95 0.96 0.92 0.89 0.86 0.82 0.77 0.74 0.73 0.72 0.72 0.71 0.69 0.67
L55 0.00 LOADER / BACKHOE, ATTACHMENTS 1.10 1.08 1.05 1.00 0.96 0.96 0.92 0.89 0.86 0.82 0.75 0.72 0.71 0.70 0.69 0.68 0.67 0.65
L60 0.00 LOG SKIDDERS 1.08 1.06 1.03 1.00 0.97 0.96 0.93 0.88 0.84 0.79 0.76 0.72 0.70 0.69 0.67 0.66 0.64 0.63
M10 0.00 MARINE EQUIPMENT (NON DREDGING)
M10 0.11 AQUATIC MAINTENANCE 1.06 1.03 1.01 1.00 0.97 0.95 0.91 0.87 0.83 0.79 0.76 0.71 0.68 0.67 0.65 0.64 0.63 0.62
M10 0.12 AQUATIC MAINTENANCE ATTACHMENTS 1.06 1.03 1.01 1.00 0.97 0.95 0.90 0.86 0.82 0.78 0.74 0.69 0.65 0.64 0.62 0.61 0.60 0.59
M10 0.21 HYDRAULIC CUTTERHEAD DREDGE, 8" OR LESS,TRANSPORTABLE 1.05 1.03 1.01 1.00 0.98 0.95 0.91 0.88 0.84 0.81 0.78 0.73 0.70 0.69 0.67 0.66 0.65 0.64
M10 0.22 HYDRAULIC CUTTERHEAD DREDGE,8" - 12",TRANSPORTABLE 1.05 1.03 1.01 1.00 0.98 0.95 0.91 0.88 0.84 0.81 0.78 0.73 0.70 0.69 0.67 0.66 0.65 0.64
M10 0.23 HYDRAULIC AUGERHEAD DREDGE,12" OR LESS,TRANSPORTABLE 1.05 1.03 1.01 1.00 0.98 0.95 0.91 0.88 0.84 0.81 0.78 0.73 0.70 0.69 0.67 0.66 0.65 0.64
M10 0.24 HYDRAULIC FLOATING PUMPS,12" OR LESS,TRANSPORTABLE 1.05 1.03 1.01 1.00 0.98 0.95 0.91 0.88 0.84 0.80 0.77 0.73 0.69 0.68 0.67 0.65 0.65 0.64
M10 0.25 HYDRAULIC DREDGE PUMPS,12" OR LESS,TRANSPORTABLE 1.06 1.03 1.01 1.00 0.97 0.95 0.91 0.87 0.83 0.79 0.76 0.71 0.67 0.66 0.64 0.63 0.63 0.61
M10 0.26 HYDRAULIC DREDGE / PUMP ATTACHMENTS 1.06 1.03 1.01 1.00 0.97 0.95 0.91 0.87 0.83 0.79 0.76 0.71 0.67 0.66 0.64 0.63 0.63 0.61
M10 0.31 SMALL MECH DREDGES,CLAMSHELL,BARGE-MTD TO 5 CY 1.05 1.04 1.01 1.00 0.97 0.97 0.94 0.93 0.92 0.87 0.81 0.79 0.77 0.71 0.73 0.72 0.71 0.70
3- 34
3-37
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
CATEGORY
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
M10 0.32 SMALL MECH DREDGES, AMPHIBIOUS EXCAVATORS 1.06 1.04 1.02 1.00 0.97 0.97 0.94 0.93 0.92 0.86 0.81 0.79 0.76 0.71 0.72 0.72 0.70 0.69
M10 0.33 SMALL MECH DREDGES,HOE-MOUNTED DREDGING ATTACH 1.05 1.03 1.01 1.00 0.98 0.95 0.91 0.87 0.83 0.80 0.77 0.72 0.69 0.68 0.66 0.65 0.64 0.63
M10 0.41 WORK FLOATS (NON-DREDGING) 1.05 1.03 1.01 1.00 0.98 0.95 0.91 0.88 0.83 0.80 0.77 0.73 0.69 0.68 0.66 0.65 0.65 0.63
M10 0.42 WORK BARGES (SECTIONAL, NON-DREDGING) 1.05 1.03 1.01 1.00 0.98 0.96 0.92 0.88 0.84 0.81 0.78 0.74 0.70 0.69 0.68 0.67 0.66 0.65
M10 0.45 FLAT-DECK OR CARGO BARGE (NON-DREDGING) 1.05 1.02 1.01 1.00 0.98 0.96 0.92 0.89 0.85 0.82 0.79 0.75 0.72 0.71 0.70 0.68 0.68 0.67
M10 0.46 DUMP SCOW (NON-DREDGING) 1.05 1.02 1.01 1.00 0.98 0.96 0.92 0.89 0.85 0.82 0.79 0.75 0.72 0.71 0.70 0.68 0.68 0.67
M10 0.47 DRILL BARGE (NON-DREDGING) 1.05 1.03 1.01 1.00 0.98 0.96 0.92 0.88 0.85 0.82 0.79 0.74 0.71 0.70 0.69 0.68 0.67 0.66
M10 0.48 ALL OTHER BARGES (NON-DREDGING) 1.05 1.03 1.01 1.00 0.98 0.96 0.92 0.88 0.85 0.82 0.79 0.74 0.71 0.70 0.69 0.68 0.67 0.66
M10 0.51 BOATS & LAUNCHES, 0 THRU 250 HP 1.06 1.03 1.01 1.00 0.98 0.95 0.91 0.87 0.83 0.80 0.77 0.72 0.68 0.67 0.66 0.64 0.64 0.63
M10 0.53 BOATS & LAUNCHES, 251 THRU 500 HP 1.05 1.03 1.01 1.00 0.98 0.95 0.91 0.88 0.84 0.81 0.78 0.73 0.70 0.69 0.67 0.66 0.65 0.64
M10 0.54 TUGS, 501 THRU 1,000 HP 1.05 1.03 1.01 1.00 0.98 0.96 0.92 0.88 0.84 0.81 0.78 0.74 0.71 0.70 0.68 0.67 0.67 0.66
M10 0.55 TUGS, 1,000 THRU 2,000 HP 1.05 1.02 1.01 1.00 0.98 0.96 0.92 0.88 0.85 0.82 0.79 0.75 0.71 0.70 0.69 0.68 0.67 0.66
P10 0.00 PILE HAMMER ACCESSORIES - EXTRACTORS & BOX LEADS 1.12 1.10 1.06 1.00 0.95 0.95 0.91 0.86 0.83 0.78 0.70 0.66 0.64 0.63 0.62 0.61 0.60 0.58
P20 0.00 PILE HAMMERS, DOUBLE ACTING
P20 0.10 DIESEL 1.11 1.09 1.05 1.00 0.96 0.96 0.92 0.88 0.85 0.80 0.74 0.70 0.69 0.68 0.67 0.66 0.65 0.63
P20 0.20 PNEUMATIC (STEAM/AIR) 1.10 1.08 1.05 1.00 0.96 0.96 0.92 0.89 0.86 0.82 0.75 0.72 0.71 0.70 0.69 0.68 0.67 0.65
P25 0.00 PILE HAMMERS, SINGLE ACTING
P25 0.10 DIESEL 1.10 1.08 1.05 1.00 0.96 0.96 0.92 0.89 0.86 0.82 0.75 0.72 0.71 0.70 0.69 0.68 0.67 0.65
P25 0.20 PNEUMATIC (STEAM/AIR) 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.87 0.83 0.77 0.74 0.73 0.71 0.71 0.70 0.69 0.67
P30 0.00 PILE HAMMERS, DRIVER/ EXTRACTOR, VIBRATORY 1.10 1.08 1.05 1.00 0.96 0.96 0.92 0.89 0.86 0.82 0.75 0.72 0.71 0.70 0.69 0.68 0.67 0.65
P35 0.00 PIPELAYERS 1.12 1.10 1.06 1.00 0.96 0.96 0.93 0.90 0.87 0.84 0.79 0.76 0.75 0.74 0.74 0.73 0.70 0.69
P40 0.00 PLATFORMS & MAN-LIFTS 1.05 1.04 1.01 1.00 0.97 0.97 0.95 0.94 0.92 0.87 0.82 0.80 0.77 0.72 0.73 0.73 0.72 0.70
3- 35
3-38
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
CATEGORY
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
P45 0.00 PUMPS, GROUT 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.90 0.87 0.83 0.77 0.74 0.73 0.72 0.71 0.70 0.69 0.68
P50 0.00 PUMPS, WATER, CENTRIFUGAL, TRASH
P50 0.11 ENGINE DRIVE 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.86 0.82 0.76 0.73 0.71 0.70 0.70 0.69 0.67 0.66
P50 0.12 ELECTRIC DRIVE 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.86 0.82 0.76 0.73 0.71 0.70 0.70 0.69 0.67 0.66
P50 0.21 WHEEL MOUNTED, ENGINE DRIVE 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.86 0.82 0.76 0.73 0.71 0.70 0.70 0.69 0.67 0.66
P50 0.22 WHEEL MOUNTED, ELECTRIC DRIVE 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.86 0.82 0.76 0.73 0.71 0.70 0.70 0.69 0.67 0.66
P50 0.31 HOSES, PUMP, SUCTION & DISCHARGE 1.09 1.08 1.05 1.00 0.97 0.96 0.93 0.90 0.88 0.84 0.78 0.75 0.74 0.73 0.72 0.72 0.71 0.69
P55 0.00 PUMPS, WATER, SUBMERSIBLE
P55 0.01 ENGINE DRIVE 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.86 0.82 0.76 0.73 0.71 0.70 0.70 0.69 0.67 0.66
P55 0.02 ELECTRIC DRIVE 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.90 0.87 0.83 0.77 0.74 0.73 0.72 0.71 0.70 0.69 0.68
P60 0.00 PUMPS, WATER, CENTRIFUGAL, DEWATERING
P60 0.11 SKID MOUNTED, ENGINE DRIVE 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.86 0.82 0.76 0.73 0.71 0.70 0.70 0.69 0.67 0.66
P60 0.12 SKID MOUNTED, ELECTRIC DRIVE 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.90 0.87 0.83 0.77 0.74 0.73 0.72 0.71 0.70 0.69 0.68
P65 0.00 PUMPS, WATER, DIAPHRAGM
P65 0.11 SKID MOUNTED, ENGINE DRIVE 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.86 0.82 0.76 0.73 0.71 0.70 0.70 0.69 0.67 0.66
P65 0.12 SKID MOUNTED, ELECTRIC DRIVE 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.90 0.87 0.83 0.77 0.74 0.73 0.72 0.71 0.70 0.69 0.68
P70 0.00 PUMPS, WATER (For core drills)
P70 0.01 ENGINE DRIVE 1.11 1.09 1.05 1.00 0.96 0.96 0.92 0.88 0.86 0.81 0.74 0.71 0.69 0.68 0.68 0.67 0.66 0.64
3- 36
3-39
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
CATEGORY
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
P70 0.02 ELECTRIC DRIVE 1.11 1.09 1.05 1.00 0.96 0.96 0.92 0.88 0.86 0.81 0.74 0.71 0.69 0.68 0.68 0.67 0.66 0.64
R10 0.00 RIPPERS & HYDRAULIC BANK SLOPERS (Add cost for point wear) 1.12 1.11 1.06 1.00 0.96 0.96 0.93 0.89 0.87 0.83 0.78 0.75 0.74 0.74 0.73 0.72 0.69 0.68
R15 0.00 ROLLERS, STATIC, TOWED, PNEUMATIC 1.07 1.06 1.03 1.00 0.97 0.96 0.93 0.88 0.83 0.78 0.74 0.70 0.68 0.67 0.66 0.67 0.65 0.63
R20 0.00 ROLLERS, STATIC, TOWED, STEEL DRUM 1.07 1.06 1.03 1.00 0.97 0.96 0.93 0.88 0.83 0.78 0.74 0.70 0.68 0.67 0.66 0.67 0.65 0.63
R30 0.00 ROLLERS, STATIC, SELF-PROPELLED
R30 0.01 PNEUMATIC 1.07 1.05 1.03 1.00 0.97 0.96 0.93 0.88 0.84 0.79 0.76 0.72 0.70 0.69 0.67 0.68 0.67 0.65
R30 0.02 SMOOTH DRUM 1.07 1.05 1.03 1.00 0.97 0.96 0.93 0.88 0.84 0.79 0.76 0.72 0.70 0.69 0.67 0.69 0.67 0.65
R30 0.03 TAMPING FOOT, LANDFILL & SOIL COMPACTORS 1.07 1.06 1.03 1.00 0.97 0.96 0.93 0.88 0.83 0.78 0.75 0.71 0.69 0.68 0.66 0.67 0.65 0.64
R40 0.00 ROLLERS, VIBRATORY, TOWED 1.08 1.06 1.03 1.00 0.97 0.96 0.93 0.87 0.83 0.78 0.74 0.70 0.68 0.67 0.65 0.67 0.65 0.63
R45 0.00 ROLLERS, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM 1.08 1.06 1.03 1.00 0.97 0.96 0.93 0.87 0.83 0.78 0.74 0.70 0.68 0.67 0.65 0.67 0.65 0.63
R50 0.00 ROLLERS, VIBRATORY, SELF-PROPELLED, SINGLE DRUM 1.08 1.06 1.03 1.00 0.97 0.96 0.92 0.87 0.82 0.77 0.73 0.68 0.66 0.65 0.63 0.65 0.63 0.61
R55 0.00 ROOFING EQUIPMENT 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.87 0.83 0.77 0.74 0.73 0.71 0.71 0.70 0.69 0.67
S10 0.00 SCRAPERS, ELEVATING
S10 0.01 0 THRU 200 HP 1.17 1.15 1.11 1.00 0.96 0.94 0.88 0.84 0.83 0.79 0.75 0.72 0.71 0.70 0.69 0.68 0.65 0.63
S10 0.02 OVER 200 HP 1.18 1.16 1.12 1.00 0.95 0.93 0.88 0.84 0.82 0.78 0.74 0.71 0.70 0.69 0.68 0.67 0.64 0.62
S15 0.00 SCRAPERS, CONVENTIONAL 1.17 1.15 1.11 1.00 0.96 0.94 0.88 0.85 0.83 0.80 0.76 0.73 0.72 0.71 0.70 0.69 0.66 0.64
S20 0.00 SCRAPERS, TANDEM POWERED 1.17 1.15 1.11 1.00 0.96 0.94 0.88 0.85 0.83 0.80 0.76 0.73 0.72 0.71 0.70 0.69 0.66 0.64
S25 0.00 SCRAPERS, TRACTOR DRAWN 1.17 1.15 1.11 1.00 0.96 0.94 0.88 0.84 0.83 0.79 0.75 0.72 0.71 0.70 0.70 0.68 0.66 0.63
S30 0.00 SCREENING & CRUSHING PLANTS
S30 0.10 CONVEYORS 1.09 1.07 1.04 1.00 0.97 0.96 0.93 0.90 0.88 0.84 0.78 0.75 0.74 0.73 0.73 0.72 0.71 0.69
S30 0.20 CRUSHERS - VERTICAL & HORIZONTAL SHAFT IMPACTOR 1.09 1.07 1.04 1.00 0.97 0.97 0.94 0.90 0.88 0.84 0.79 0.76 0.75 0.74 0.74 0.73 0.72 0.70
S30 0.21 CRUSHERS - CONE 1.09 1.07 1.04 1.00 0.97 0.97 0.94 0.90 0.88 0.84 0.79 0.76 0.75 0.74 0.74 0.73 0.72 0.70
3- 37
3-40
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
CATEGORY
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
S30 0.22 CRUSHERS - JAW 1.09 1.07 1.04 1.00 0.97 0.97 0.94 0.90 0.88 0.84 0.79 0.76 0.75 0.74 0.74 0.73 0.72 0.70
S30 0.30 SCREENING PLANT 1.09 1.07 1.04 1.00 0.97 0.96 0.93 0.90 0.88 0.84 0.78 0.75 0.74 0.73 0.73 0.72 0.71 0.69
S35 0.00 SNOW REMOVAL EQUIPMENT 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.86 0.82 0.76 0.73 0.71 0.70 0.70 0.69 0.67 0.66
S40 0.00 SOIL & ROAD STABILIZERS 1.17 1.15 1.11 1.00 0.96 0.94 0.88 0.84 0.83 0.79 0.75 0.72 0.71 0.70 0.69 0.68 0.65 0.63
S45 0.00 SPLITTERS, ROCK & CONCRETE 1.10 1.08 1.05 1.00 0.96 0.96 0.92 0.89 0.86 0.82 0.75 0.72 0.71 0.70 0.69 0.68 0.67 0.65
T10 0.00 TRACTOR BLADES & ATTACHMENTS (including agricultural) 1.12 1.11 1.06 1.00 0.96 0.96 0.93 0.89 0.87 0.83 0.78 0.76 0.74 0.74 0.73 0.72 0.70 0.68
T15 0.00 TRACTORS, CRAWLER (DOZER) (includes blade)
T15 0.01 0 THRU 225 HP 1.14 1.12 1.07 1.00 0.95 0.95 0.92 0.88 0.86 0.81 0.76 0.73 0.71 0.71 0.70 0.69 0.66 0.64
T15 0.02 226 HP THRU 425 HP 1.13 1.11 1.06 1.00 0.95 0.96 0.92 0.89 0.87 0.83 0.77 0.75 0.73 0.73 0.72 0.71 0.68 0.67
T15 0.03 OVER 425 HP 1.12 1.10 1.06 1.00 0.96 0.96 0.93 0.90 0.88 0.84 0.79 0.76 0.75 0.74 0.74 0.73 0.70 0.69
T20 0.00 TRACTORS, WHEEL TYPE (DOZER) 1.08 1.06 1.03 1.00 0.97 0.97 0.93 0.88 0.84 0.80 0.76 0.72 0.70 0.69 0.68 0.67 0.64 0.63
T25 0.00 TRACTORS, AGRICULTURAL
T25 0.10 CRAWLER 1.08 1.06 1.03 1.00 0.97 0.96 0.93 0.88 0.84 0.79 0.76 0.72 0.70 0.69 0.67 0.66 0.64 0.63
T25 0.20 WHEEL 1.08 1.06 1.03 1.00 0.97 0.96 0.93 0.88 0.84 0.79 0.76 0.72 0.70 0.69 0.67 0.66 0.64 0.62
T30 0.00 TRENCHERS, CHAIN TYPE CUTTER 1.07 1.06 1.03 1.00 0.97 0.96 0.93 0.87 0.83 0.78 0.74 0.67 0.68 0.67 0.65 0.64 0.61 0.58
T35 0.00 TRENCHERS, WHEEL TYPE CUTTER 1.07 1.06 1.03 1.00 0.97 0.96 0.93 0.87 0.83 0.78 0.74 0.67 0.68 0.67 0.65 0.64 0.61 0.58
T40 0.00 TRUCK OPTIONS
T40 0.10 CRANES / HOISTS, PERSONNEL & MATERIAL HANDLING 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.86 0.82 0.76 0.73 0.71 0.70 0.70 0.69 0.67 0.66
T40 0.20 DUMP BODY, REAR 1.09 1.07 1.04 1.00 0.97 0.96 0.93 0.90 0.88 0.84 0.78 0.75 0.74 0.73 0.73 0.72 0.71 0.69
T40 0.30 FLATBEDS, WITH SIDES 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.86 0.82 0.76 0.73 0.71 0.70 0.70 0.69 0.67 0.66
T40 0.41 HOIST, ELECTRIC DRIVE 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.86 0.82 0.76 0.73 0.71 0.70 0.70 0.69 0.67 0.66
T40 0.50 TRANSIT MIXERS 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.90 0.87 0.83 0.77 0.74 0.73 0.72 0.71 0.70 0.69 0.68
3- 38
3-41
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
CATEGORY
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
T40 0.60 WATER TANKS 1.11 1.09 1.05 1.00 0.96 0.96 0.92 0.88 0.86 0.81 0.74 0.71 0.69 0.68 0.68 0.67 0.66 0.64
T40 0.70 ALL OTHER OPTIONS 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.86 0.82 0.76 0.73 0.71 0.70 0.70 0.69 0.67 0.66
T45 0.00 TRUCK TRAILERS
T45 0.10 BOTTOM DUMP 1.09 1.07 1.04 1.00 0.97 0.96 0.93 0.90 0.88 0.84 0.78 0.75 0.74 0.73 0.73 0.72 0.71 0.69
T45 0.20 END DUMP 1.09 1.07 1.04 1.00 0.97 0.96 0.93 0.90 0.88 0.84 0.78 0.75 0.74 0.73 0.73 0.72 0.71 0.69
T45 0.30 PUP TRAILER 1.09 1.07 1.04 1.00 0.97 0.96 0.93 0.90 0.88 0.84 0.78 0.75 0.74 0.73 0.73 0.72 0.71 0.69
T45 0.41 LOWBOY, RIGID NECK, DROP DECK 1.09 1.07 1.04 1.00 0.97 0.96 0.93 0.90 0.88 0.84 0.78 0.75 0.74 0.73 0.73 0.72 0.71 0.69
T45 0.50 FLATBED TRAILER 1.09 1.07 1.04 1.00 0.97 0.96 0.93 0.90 0.88 0.84 0.78 0.75 0.74 0.73 0.73 0.72 0.71 0.69
T45 0.60 MISCELLANEOUS / UTILITY 1.09 1.07 1.04 1.00 0.97 0.96 0.93 0.90 0.88 0.84 0.78 0.75 0.74 0.73 0.73 0.72 0.71 0.69
T45 0.70 WATER TANKER TRAILER 1.11 1.09 1.05 1.00 0.96 0.96 0.92 0.88 0.86 0.81 0.75 0.71 0.70 0.69 0.68 0.67 0.66 0.64
T45 0.80 DECONTAMINATION FACILITY 1.11 1.09 1.05 1.00 0.96 0.96 0.92 0.88 0.86 0.81 0.74 0.71 0.69 0.68 0.68 0.67 0.66 0.64
T45 0.90 TANK TRAILERS 1.11 1.09 1.05 1.00 0.96 0.96 0.92 0.88 0.86 0.81 0.75 0.71 0.70 0.69 0.68 0.67 0.66 0.64
T50 0.00 TRUCKS, HIGHWAY (Add attachments as required)
T50 0.01 0 THRU 10,000 GVW 1.13 1.11 1.07 1.00 0.96 0.94 0.89 0.85 0.82 0.78 0.74 0.72 0.71 0.69 0.69 0.71 0.69 0.69
T50 0.02 OVER 10,000 THRU 30,000 GVW (Chassis only - Add options) 1.13 1.10 1.07 1.00 0.96 0.94 0.89 0.85 0.82 0.78 0.74 0.72 0.71 0.69 0.69 0.71 0.69 0.70
T50 0.03 OVER 30,000 GVW (Chassis only - Add options) 1.12 1.10 1.07 1.00 0.97 0.94 0.89 0.85 0.82 0.78 0.74 0.72 0.71 0.69 0.69 0.71 0.69 0.70
T55 0.00 TRUCKS, OFF-HIGHWAY
T55 0.10 RIGID FRAME 1.05 1.03 1.02 1.00 0.98 0.98 0.96 0.92 0.90 0.85 0.79 0.74 0.73 0.72 0.70 0.69 0.68 0.67
T55 0.20 ARTICULATED FRAME 1.05 1.03 1.02 1.00 0.98 0.98 0.96 0.92 0.90 0.85 0.78 0.74 0.73 0.71 0.70 0.68 0.67 0.66
T56 0.00 TRUCKS,OFF-HIGHWAY/PRIME MOVER TRACTORS & WAGONS
T56 0.10 PRIME MOVER TRACTORS 1.05 1.03 1.02 1.00 0.98 0.98 0.96 0.92 0.90 0.85 0.79 0.74 0.73 0.72 0.70 0.69 0.68 0.67
T56 0.20 WAGONS, BOTTOM DUMP 1.06 1.03 1.02 1.00 0.98 0.98 0.96 0.92 0.89 0.84 0.77 0.73 0.72 0.70 0.69 0.67 0.66 0.65
3- 39
3-42
EP 1110-1-8 EP 1110-1-8, Vol. 2
(Vol. 2) 30 Apr 14
4/30/2014
CATEGORY
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
T56 0.30 WAGONS, REAR DUMP 1.06 1.03 1.02 1.00 0.98 0.98 0.96 0.92 0.89 0.84 0.77 0.72 0.71 0.70 0.68 0.66 0.65 0.64
T57 0.00 TRUCKS, VACUUM 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.86 0.82 0.76 0.73 0.71 0.70 0.70 0.69 0.68 0.66
T60 0.00 TRUCKS, WATER, OFF-HIGHWAY 1.06 1.03 1.02 1.00 0.98 0.98 0.96 0.92 0.89 0.84 0.77 0.72 0.71 0.70 0.68 0.66 0.65 0.64
T65 0.00 TUNNEL/MINING EQUIPMENT
T65 0.10 DRIFTING & TUNNELING DRILLS 1.07 1.05 1.03 1.00 0.96 0.95 0.92 0.86 0.80 0.74 0.68 0.63 0.62 0.56 0.55 0.54 0.53 0.52
T65 0.20 TUNNEL BORING MACHINES 1.09 1.08 1.05 1.00 0.97 0.96 0.93 0.90 0.88 0.83 0.78 0.75 0.74 0.73 0.72 0.71 0.70 0.69
T65 0.30 PRODUCTION DRILLING RIGS 1.07 1.05 1.03 1.00 0.96 0.95 0.92 0.86 0.80 0.73 0.68 0.63 0.62 0.56 0.55 0.54 0.53 0.52
T65 0.40 ROADHEADERS & CONTINUOUS MINERS 1.09 1.08 1.05 1.00 0.97 0.96 0.93 0.90 0.87 0.83 0.78 0.75 0.73 0.72 0.72 0.71 0.70 0.68
T65 0.50 ROCK BOLTING EQUIPMENT 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.86 0.82 0.76 0.73 0.71 0.70 0.70 0.69 0.68 0.66
T65 0.61 LOADING & HAULING EQUIPMENT, DIESEL OR GAS 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.87 0.82 0.76 0.73 0.72 0.71 0.70 0.69 0.68 0.66
T65 0.62 LOADING & HAULING EQUIPMENT, ELECTRIC 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.87 0.82 0.76 0.73 0.72 0.71 0.71 0.70 0.68 0.67
T65 0.63 LOADING & HAULING EQUIPMENT, AIR-POWERED 1.11 1.09 1.05 1.00 0.96 0.96 0.92 0.88 0.86 0.81 0.75 0.71 0.70 0.69 0.68 0.67 0.66 0.64
T65 0.70 LOCOMOTIVES 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.87 0.82 0.76 0.73 0.72 0.71 0.70 0.69 0.68 0.66
T65 0.90 OTHER TUNNELING EQUIPMENT 1.10 1.08 1.05 1.00 0.96 0.96 0.93 0.89 0.86 0.82 0.76 0.73 0.71 0.70 0.70 0.69 0.68 0.66
W10 0.00 WAGONS, BOTTOM DUMP 1.05 1.03 1.02 1.00 0.98 0.98 0.96 0.92 0.90 0.85 0.78 0.73 0.73 0.71 0.70 0.68 0.67 0.66
W15 0.00 WAGONS, REAR DUMP 1.05 1.03 1.02 1.00 0.98 0.98 0.96 0.92 0.90 0.85 0.78 0.73 0.73 0.71 0.70 0.68 0.67 0.66
W25 0.00 WATER & CO2 BLASTERS
W25 0.10 LOW PRESSURE, (< 5,000 PSI) 1.10 1.09 1.05 1.00 0.96 0.96 0.92 0.89 0.86 0.81 0.75 0.72 0.70 0.69 0.69 0.68 0.67 0.65
W25 0.20 HIGH PRESSURE, (>= 5,000 PSI) 1.10 1.09 1.05 1.00 0.96 0.96 0.92 0.89 0.86 0.81 0.75 0.72 0.70 0.69 0.69 0.68 0.67 0.65
W25 0.30 STEAM CLEANERS 1.10 1.09 1.05 1.00 0.96 0.96 0.92 0.89 0.86 0.81 0.75 0.72 0.70 0.69 0.69 0.68 0.67 0.65
W25 0.40 CO2 BLASTERS 1.10 1.08 1.05 1.00 0.96 0.96 0.92 0.89 0.86 0.82 0.75 0.72 0.71 0.70 0.69 0.68 0.67 0.65
W25 0.50 WET ABRASIVE BLASTING SYSTEM (TORBO) 1.12 1.10 1.06 1.00 0.96 0.95 0.91 0.87 0.84 0.79 0.71 0.68 0.66 0.64 0.64 0.63 0.62 0.59
3- 40
3-43
EP 1110-1-8, Vol. 2 EP 1110-1-8
30 Apr 14 (Vol. 2)
4/30/2014
CATEGORY
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
W30 0.00 WATER TANKS
W30 0.10 PORTABLE WITH WHEELS 1.06 1.03 1.02 1.00 0.98 0.98 0.96 0.92 0.89 0.84 0.77 0.72 0.71 0.70 0.68 0.66 0.65 0.64
W30 0.20 SKID MOUNTED 1.06 1.03 1.02 1.00 0.98 0.98 0.96 0.92 0.89 0.84 0.77 0.72 0.71 0.70 0.68 0.66 0.65 0.64
W35 0.00 WELDERS
W35 0.10 ENGINE DRIVEN 1.11 1.09 1.05 1.00 0.96 0.96 0.92 0.88 0.86 0.81 0.74 0.71 0.69 0.68 0.68 0.67 0.66 0.64
W35 0.20 ELECTRIC DRIVEN 1.10 1.08 1.05 1.00 0.96 0.96 0.92 0.89 0.86 0.82 0.75 0.72 0.71 0.70 0.69 0.68 0.67 0.65
3- 41
3-44
EP 1110-1-8, Vol. 2
30 Apr 14
STANDBY HOURLY RATE CALCULATION FOR OVERAGE EQUIPMENT
EXAMPLE
Assume the following set of given information for the rate calculation example:
1. The unit of equipment is not listed in table 2-1.
2. The equipment is contractor owned.
3. Data for the unit in question:
a. Caterpillar front-end wheel loader

b. Model 950-G, 4WD, 3.5 CY capacity
c. Serial number indicates year of manufacture = 2002
d. Actual purchase price in 2002 = $205,000
(includes all regional discounts, sales tax and freight)
e. Horsepower is 180 hp (fuel is Diesel off-road)
f. Drive tire (DT) size = 23.50 x 25, 16 ply, L-3 (appendix F tire code ANNB5)
DT cost (2014) = 4 tires x $4,233/tire = $16,932
g. Weight = 39,200 lbs
4. Use the actual cost data as follows:
a. Purchase price (TEV) = $205,000

b. Year of manufacture = 2002
5. Hourly rate is computed as follows:
Figure 3-2. Total Hourly Rate Calculation for Overage Equipment
3-45
EP 1110-1-8, Vol. 2
30 Apr 14
Example: The piece of equipment shown in this example is based on a known piece of equipment
for illustration purposes only.
USE THIS WORKSHEET TO COMPUTE A HOURLY RATE FOR EQUIPMENT THAT IS NOT IN THIS PAMPHLET OR IS IN THE
PAMPHLET BUT NOT EQUIVALENT IN SIZE, CAPACITY, HORSEPOWER OR VALUE. (See Appendix A for a blank form)
Region 02
1. EQUIPMENT INFORMATION AND EXPENSE FACTORS ID No:

(1) Equipment Description: Loader, Front-end, Wheel, 4WD, 3.5 CY capacity
(2) Model and Series: Caterpillar Model 950-G
(4) Year Manufactured: 2002
6-marine diesel 3
0
6-marine diesel from 0 to 6 ==> None
(8) Shipping Weight (cwt): 392 cwt
(9) Tire size and number of tires: (Cost of tires based on present year - see 1.a.(3) and Appendix F)
(a) Front (FT): 0 $0 $0
(b) Drive (DT): 23.5X25/16Ply ANNB5 4 $4,233 $16,932
[at Year (yr) of Manufacture] $0 OR actual purchase price: $205,000

b. Category and Subcategory Number: L40 0.11
3-46
EP 1110-1-8, Vol. 2
30 Apr 14
Region 02
2. EQUIPMENT VALUE
a. List Price + Accessories: [at Year (yr) of Manufacture] = $0
(1) Discount: (List Price + Accessories) x Discount

{1.a.(10)} {1.c.(3)}
($0 + $0.00) x 0.075 = - [ $0 ]
(2) Subtotal {2.a.} - {2.a.(1)} Subtotal = $0
(3) Sales or Import Tax: Subtotal x Tax Rate

$0 x 6.00% = $0
(4) Total Discounted Price: {Subtotal: 2.a.(2) + 2.a.(3)} Subtotal = $0
Freight Rate
b. Freight: Shipping Weight x per cwt
0,000 cwt x $0.00 /cwt = $0
c. TOTAL EQUIPMENT VALUE (TEV): TOTAL[2.]: = $205,000

a. LIFE / Working Hours Per Year (WHPY) = N

9,250 hr / 1,450 hr/yr = 6.38 yrs
4. OWNERSHIP COST
a. Depreciation
Tire Index, Year of Tire Index, Present Year or Year
Manufacture, of Use
{1.a.(4)} / {1.a.(3)} = TCI
2430 / 4050 = 0.600

{2.c.} {1.c.(5)} {4.a.(1)} {1.a.(9)(d)} {1.c.(4)}
[$205,000 x (1.0-0.25) - (0.600 x $16,932 )] / 9,250 /hr = $15.52 /hr
3-47
EP 1110-1-8, Vol. 2
30 Apr 14
Region 02

Avg Value
(1) [( N - 1.0) x (1.0 + SLV) + 2.0] / (2.0 x N) = Factor
{3.a.} {1.c.5.} {3.a.} (AVF)
[(6.38 yr - 1.0) x (1.0 + 0.25) + 2.0] / (2.0 x 6.38 yr) = 0.684
Adjusted
$205,000 x 0.684 x 1.70% / 1,450 hr/yr = $1.64 /hr

{4.a.(2)} + {4.b.(2)}
5. OPERATING COST
a. Fuel Costs:
(1) Equipment:
Fuel Cost per Gallon

Fuel Factor x Horsepower (hp) x (gal)
{1.c.(6)} {1.a.(5)} {Appendix B}
0.000 x 0 hp x $0.00 /gal = $0.00 /hr
(2) Carrier:
Fuel Factor x hp x Fuel Cost per gal

{1.c.(7)} {1.a.(6)} {Appendix B}
0.000 x 0 hp x $0.00 /gal = $0.00 /hr

{5.a (1)} + {5.a (2)}
b. FOG Cost:
(1) Equipment:
Equipment Hourly Fuel Labor Adjustment

FOG Factor x Cost x Factor (LAF)
{1.c.(8)} {5.a.(1)} {Appendix B}
0.000 x $0.00 /hr x 0.00 = $0.00 /hr
3-48
EP 1110-1-8, Vol. 2
30 Apr 14
Region 02
(2) Carrier:
Carrier Hourly
{1.c.(8)} {5.a.(2)} {Appendix B}
0.000 x $0.00 /hr x 0.00 = $0.00 /hr

{5.b.(1)} + {5.b.(2)}

d. Repair Cost:

EK is from {1.c.(1)}
Economic Index, / Economic Index,

Present Year or Year of Manufacture,
Year of {1.a.(4)}
Appendix E, Appendix E, EK={1.c.(1)}
EK={1.c.(1)}
0000 / 0000 = 0.000

RCF x EAF x LAF = RF

{1.c.(10)} {5.d.(1)} {Appendix B}
0.00 x 0.000 x 0.00 = 0.000
(3) Repair Cost:

{2.c.} {4.a.(1)} {1.a.(9)(d)} {5.d.(2)} {1.c.(4)}
[$0 - (0.000 x $0)] x 0.000 / 0
3-49
EP 1110-1-8, Vol. 2
30 Apr 14
Region 02

{1.a.(9)(a)} {1.c.(9)(a)} {Appendix F}
(1.5 x $0) / (1.8 x 0.00 x 0 hrs) = $0.00/hr

{1.a.(9)(b)} {1.c.(9)(b)} {Appendix F}
(1.5 x ($0) / (1.8 x 0.00 x 0 hrs = $0.00/hr

{1.a.(9)(c)} {1.c.(9)(c)} {Appendix F}
(1.5 x $0) / (1.8 x 0.00 x 0 hr) = $0.00/hr
(4) Total Tire Wear Cost: Total [5.e.] = $0.00/hr

Sum {5.e.(1)} through {5.e.(3)}

$0.00/hr x (0.15 x 0.00) Total [5.f.] = $0.00/hr
g. TOTAL HOURLY OPERATING COST: Total [5.] = $0.00/hr

Sum {5.a.} through {5.f.}
3-50
EP 1110-1-8, Vol. 2
30 Apr 14
Region 02
6. HOURLY RATES

{4.c.} {5.g.}
$0.00 /hr + $0.00 /hr = $0.00 /hr
See Figure 3-1 for hourly rate calculations for overage equipment

Depreciation + (FCCM x 40 hr/wk / Work hr/wk) + Operating

Cost
{4.a.(2)} {4.b.(2)} example:60 hr/wk {5.g.}
$0.00 /hr + $0.00 /hr x 40 hr/wk / 60 hr/wk + $0.00 /hr = $0.00 /hr
example:60 hr/wk

{4.a.(2)} {4.b.(2)}
($15.52 /hr x 0.50) + $1.64 /hr = $9.40 /hr
3-51
EP 1110-1-8, Vol. 2
30 Apr 14
3-52
EP 1110-1-8, Vol. 2
30 Apr 14
CHAPTER 4
Methodology for Dredging Plant and Marine Equipment
SECTION I. GENERAL
4.1 Contents. This chapter contains the methodology used to compute ownership and
operating rates for dredging plant and permanent floating plant such as floating pile-
driving equipment. Dredging plant is marine equipment used for dredging operations for
the majority of its life or designed and built for marine/dredging use.
4.2 General.
a. The ownership and operating rates provided in table 2-1, category M-10, are
based on the methodology in chapter 2 for non-dredging equipment. However, the cost
data (Acquisition Cost, Horsepower, and Fuel Type) may be used for calculation of
dredging plant and marine equipment rates, provided they are calculated in accordance
with the methodology in this chapter.
b. Table 4-1 shows ownership and operating cost factors for various types of
dredging plant. When a type of plant is not listed, the cost is estimated by using the
factors listed in this table for a similar type of plant.
c. The methodology for determining operating rates for hopper dredges was
omitted from this pamphlet due to the limited number of hopper dredges and the
complexity of the methods used to calculate the rates. Further information can be found
in Engineer Regulation (ER) 1110-2-1302, Engineering and Design, Civil Works Cost
Engineering, and in Engineer Technical Letter (ETL) 1110-2-573 Engineering and
Design: Construction Cost Estimating Guide for Civil Works. The internet locations for
downloading these documents are provided in Appendix A. The methodology for
calculating ownership cost is in section V of this chapter.
d. For mechanical dredges, the cost of the bucket is typically included in the plant
value; therefore, no additional allowance should be made for ownership cost. If the
bucket cost is not included in the plant value, the bucket may be treated as a separate
unit of equipment.
SECTION II. ANNUAL USE
4.3 Time Available to Dredge. The number of months available per calendar year (yr)
for dredging shall be based on the work time available to dredge, excluding downtime
for major repairs, work in dry dock, bad weather, and environmental restrictions. Figure
4-1 depicts months available for dredging, including mobilization and demobilization,
based on historic data collected by the U.S. Army Corps of Engineers’ regional dredge
4-1
EP 1110-1-8, Vol. 2
30 Apr 14
estimating teams. The data in figure 4-1 shall be used for computing the ownership
costs unless specified otherwise in the contract documents.
AVAILABLE TIME TO DREDGE BY REGION

(In Months)
Type of Dredging Operation
Region Pipeline Bucket Hopper
Atlantic Coast and tributaries 9 10 10
Gulf Coast, Lower Mississippi, and 10 10 11

Tributaries
Great Lakes, Upper Mississippi, 8 8 8

and Tributaries
West Coast and Tributaries 9 9 9
Figure 4-1. Months Available by Region
SECTION III. LIFE
4.4 Life. The life for determining ownership and operating costs is defined as follows:
a. The Useful Life is expressed in years in table 4-1. It is the economic life of the
equipment and is used to develop ownership rates for various types of dredging plant.
b. The Physical Life is expressed in hours (hrs) in table 4-1. It is the life of the unit
based on effective working time and is used to develop operating rates for various types
of dredging plant.
4.5 Annual Hours Available. The annual hours available to dredge can be established
for each type of plant based on the months available and the estimated effective
monthly hours worked. Dredging time is defined as effective plus non-effective working
time. “Effective working time" is defined as time during the dredging operation when
actual production is taking place. "Non-effective working time" is defined as time during
the dredging operation when the dredge is operational but no production is taking place.
For further information see ER 1110-2-1302, Engineering and Design, Civil Works
4-2
EP 1110-1-8, Vol. 2
30 Apr 14
Cost Engineering. The total annual hours available can be expressed by formula, as
follows:
Available Hours per yr = Months Available/yr x Effective Hours/Month
Where:
a. Months Available/yr is found in figure 4-1.
b. Effective Hours/Month is the effective working time.
SECTION IV. SALVAGE VALUE
4.6 Salvage Value (SLV). The salvage value, expressed as a decimal, is shown in
table 4-1 for different types of plant.
SECTION V. OWNERSHIP COST
4.7 Ownership Cost. Ownership cost is calculated based on a percent of plant value.
Plant value is the acquisition cost plus the cost of any initial capital improvements. The
value of initial capital improvements is based on those betterments, which were made
within 1 year of purchase. Capital improvements do not include any replacement or
repair work. Repairs or replacements are an operating cost and are covered in the
repair cost allowance. Capital improvements are considered betterments, where the
plant has been improved (e.g., adding radar or upgrade of engines). (Note: Only the
cost difference between replacement of existing similar engines and actual cost for
upgrading engines should be considered as capital improvement). For capital
improvements not made within the first year after the initial acquisition, see section VIII.
a. The ownership cost is determined from the plant value and is the total expense
rate based on depreciation and CMR. When cost or pricing data is available, the actual
acquisition price shall be used. Otherwise, the value of a similar piece of plant is used
and, if necessary, adjusted so that capacity, size, and horsepower are properly
considered.
b. Ownership rate is determined on a yearly basis and distributed over a monthly

basis. The monthly rate is calculated based on the available use months by using the
following formula:
Plant Value x (Yearly DEPR Percent + Yearly CMR Percent)

Monthly Ownership Cost =
Available Use Months
4-3
EP 1110-1-8, Vol. 2
30 Apr 14
Where:
(1) Plant Value = Acquisition price plus initial capital improvements.
(2) Yearly DEPR Percent = Ownership percent per year for depreciation.
(3) Yearly CMR Percent = Ownership percent per year for cost of money rate.
(4) Available Use Months is from figure 4-1.
4.8 Depreciation Factor. Depreciation is computed using the straight-line method. The
depreciable value is the acquisition cost, plus initial capital improvements, less
estimated salvage. The basis for determining the yearly percentage factor for
depreciation is expressed by the following formula:
Yearly DEPR Percent = (1 - SLV) /N
Where:
a. N = Useful Life from table 4-1.
b. SLV = Salvage Value from table 4-1.
4.9 The Cost of Money Rate (CMR) Factor. The CMR factor is calculated on a yearly
basis and is expressed here as an annual percentage factor. The CMR used in the
calculation is the rate in effect at the time the work was performed. This formula is
expressed as follows:
[(N - 1)(1 + SLV) + 2](discounted CMR)

Yearly CMR Percent =
2N
Where:
a. N = Useful Life from table 4-1.
b. SLV = Salvage Value from table 4-1.
c. Discounted CMR = Cost of money rate (appendix I) reduced by 25 percent for

overhead and profit allowance.
4.10 Other Ownership Elements. Taxes, storage (lay up), and insurance are
considered indirect (overhead) costs. These costs are not included in ownership rates
since they vary by geographic area and with individual contractors. These costs are
4-4
EP 1110-1-8, Vol. 2
30 Apr 14
considered as overhead costs and are, therefore, not included here so they will not be
duplicated in the overhead in the estimate or submitted proposal.
SECTION VI. OPERATING FACTORS
4.11 Hourly Operating Cost. Operating cost is based on effective working time.
Dredging plant operating factors are shown in table 4-1. These factors, which are
described in paragraph 4.12, are not intended to replace historical data but shall be
used when historical data is limited or nonexistent.
4.12 Prime and Secondary Power. Prime power refers to the primary operating engine
for the dredge or other piece of attendant plant. Secondary power refers to all other
secondary engines or power plants. If more than one secondary power engine is
present, the horsepower is totaled. Fuel consumption factors are prepared on the same
basis as in chapter 2. Hourly fuel costs are calculated separately for the primary and
secondary engines. The formula used is expressed as follows:
Hourly Fuel Cost = Horsepower x Fuel Cost/Gallon x Engine Fuel Factor
Where:
a. Horsepower is the engines rated horsepower.
b. Fuel Cost/Gallon is based on values shown in appendix B. See chapter 3 for

fuel cost adjustments.
c. Fuel Factor - Gas or Diesel Fuel. The fuel factor is listed in table 4-1 for the
primary and secondary engines.
4.13 Water, Lube, and Supplies (WLS). This factor is similar to the filters, oil, and
grease (FOG) factor described in chapter 2. This item is computed as either a
percentage of the hourly fuel costs or, if the type of plant has no engine, a reasonable
hourly cost should be included. This factor does not include an allowance for the oiler
normally assigned to the dredge or other piece of dredging plant. The formula is
expressed as follows:
Water, Lube, and Supply Cost = WLS factor x Hourly Fuel Cost
Where:
a. WLS Factor is obtained from table 4-1.
b. Hourly Fuel cost is calculated as shown in paragraph 4-12.
4-5
EP 1110-1-8, Vol. 2
30 Apr 14
4.14 Repair Factor (RPR). This factor includes an allownce for all major and minor
repairs and is similar to the maintenance and repair cost factor (RCF) described in
chapter 2. The economic adjustment factor (EAF) and the labor adjustment factor (LAF)
are required to develop this cost. The formula is expressed as follows:
(Total Plant Value x RPR x EAF x LAF)

Repair Cost =
Life in hr
Where:
a. Total Plant Value = Acquisition price plus Initial capital improvements.
b. RPR = Repair Factor from table 4-1.
c. EAF = Economic Index (present year)/ Economic Index (acquisition year).
d. LAF = Labor Adjustment Factor from appendix B.
e. Life in hrs = Physical Life from table 4-1.
It should be noted that the repair allowance does not include the following estimated
additive items:
f. Excessive dredge wear for parts (e.g., cutter teeth and main suction pumps) is
not included due to the wide variety of materials being dredged. The original cost of the
bucket and normal wear are typically included in the plant value covered in the plant
rate. Excessive bucket wear for mechanical dredges is estimated as an additive item or
treated as a separate unit of equipment from table 2-1. Allowances for wear due to
abrasive material should only be included as an additive item if it is warranted and is not
considered elsewhere in the estimate.
g. Dry docking costs, which represent an allowance for rental of the dry dock
facility, are not included because they vary greatly depending on the facilities available.
Repairs incurred while in dry dock, which occur periodically, are in the repairs. Dry
docking costs will be allocated on an average annual basis over the years between
such occurrences in accordance with cost accounting standards and generally accepted
accounting principles and practices.
h. There is no predetermined allowance in the dredging plant methodology for

jobsite yard costs, mobilization, or demobilization. All of these cost elements must be
separately estimated to match each project’s construction conditions.
4-6
EP 1110-1-8, Vol. 2
30 Apr 14
SECTION VII. STANDBY
4.15 Standby Rate. The standby rate is computed by allowing the full ownership cost.
In addition to the standby ownership rate, it may be necessary on dredges to include
operating costs. Examples of allowable operating cost are as follows: a generator fuel
allowance to account for operation of a diesel engine generator for power to operate
pumps; navigation lights; minimum crew; etc.
a. Standby is a directed delay by the Government and will not be allowed during
periods when the plant would have otherwise been in idle status, such as non-effective
working time. Since ownership is calculated based on life in years computed monthly,
standby should be paid only when additional time has been directed by the
Government. Standby is to be paid on a 24-hour basis.
b. Standby for pipeline and accessories shall be based on pumping mud in

determining values from table 4-1.
SECTION VIII. NEGOTIATED PROCUREMENT
4.16 Rates. The calculated dredging plant rates based on the methodology presented
in this chapter should be used for preparing a reasonable contract estimate. When
adequate cost or pricing data is available and submitted by the contractor for negotiated
procurement, the rates may be adjusted in accordance with the methodology in this
chapter. Cost or pricing data is defined in FAR 15.4, Contract Pricing.
4.17 Allowance for Additional Capital Improvements. Allowance for additional capital
improvements shall be calculated in accordance with generally accepted accounting
principles. When adequate cost or pricing data is not available, factors for a similar unit
of equipment may be used for determining the ownership rate for overage equipment
and plant.
4.18 Overage Plant. When the plant has exceeded the useful life given in table 4-1, it
is considered overage. The ownership rate for overage plant should be determined with
the same methodology described in section V.
a. When actual cost or pricing data is available to adjust the operating rate, the
data must be accurate, complete, and established in accordance with generally
accepted accounting principles.
b. When actual cost or pricing data is not available, the total hourly operating rate
for overage equipment shall be computed on the basis that the equipment is equal to
the useful life as shown in table 4-1.
4-7
EP 1110-1-8, Vol. 2
30 Apr 14
4.19 Dredging Plant Purchased Used. For plant purchased used, the ownership and
operating rate must be calculated on an individual case, due to the varying conditions.
When actual cost or pricing data is not available, the methodology from this chapter
shall be used and values for life and salvage from table 4-1 can be adjusted. Support
for adjustments can be obtained by calling the Chief, Cost Engineering Branch,
Engineering and Construction Division, Walla Walla District, U.S. Army Corps of
Engineers (CENWW-EC-X), telephone 509-527-7511 or 509-527-7510.
SECTION IX. RATE CALCULATION EXAMPLE
4.20 Rate Calculation Example. The example shown in figure 4-2 illustrates the use of
figure 4-1, table 4-1, and the regional data from appendix B to generate a rate. For
illustration purposes, assume that a 24-inch hydraulic dredge (pipeline) was purchased
new in 1997 for $4,500,000, including tax and delivery, and there were no initial capital
improvements. This example uses 500 hours per month and a discounted CMR of 1.70
percent.
4-8
EP 1110-1-8, Vol. 2
30 Apr 14
Table 4-1. Dredging Plant Cost Factors
Useful Physical Salvage Prime Engine Secondary Engine WLS RPR

Type of Plant Life Life Value Fuel Factor Fuel Factor % %
YRS HR SLV HPF G D HPF G D G D
Hydraulic Dredges - Pipeline
(Cutterhead or Dustpan)
(Based on Discharge
Diameter)
(Non-Truckable)
8 inch and under 5 10,000 0.05 80 0.083 0.045 70 0.072 0.039 20 22 70
9 inch through 10 inch 6 12,000 0.05 80 0.083 0.045 70 0.072 0.039 20 22 80
30 inch or larger 30 135,000 0.10 80 0.083 0.045 70 0.072 0.039 20 22 130
Barge Mounted Booster Pump

(For Pipeline Dredges)
30 inch or larger 30 135,000 0.10 80 0.083 0.045 70 0.072 0.039 22 24 120
SLV = Salvage Value HPF = Horsepower Factor G = Gas D = Diesel

WLS = Water, Lube and Supplies RPR = Repairs
4-9
EP 1110-1-8, Vol. 2
30 Apr 14
Table 4-1. Dredging Plant Cost Factors (Continued)

1
Mechanical Dredges (Large)
Clamshell - under 5 cy 8 18,000 0.05 70 0.072 0.039 60 0.062 0.033 22 24 90
Clamshell - 6 cy to 10 cy 13 26,000 0.05 70 0.072 0.039 60 0.062 0.033 22 24 100
Clamshell - 20 cy and over 30 90,000 0.05 70 0.072 0.039 60 0.062 0.033 22 24 130
All Other Types
(Bucket or Dipper) 25 90,000 0.10 70 0.072 0.039 60 0.062 0.033 22 24 120
Barge Mounted Crane with
Clamshell Bucket
Non - Dredging
Clamshell - under 6 cy 9 18,000 0.05 55 0.055 0.031 45 0.045 0.025 22 24 85
Barge Mounted Lifting Crane
25 Ton to 75 Ton, 45’ Boom 9 18,000 0.05 40 0.040 0.022 30 0.030 0.017 22 24 80
75 Ton to 125 Ton, 60’ Boom 14 28,000 0.05 40 0.040 0.022 30 0.030 0.017 22 24 90
Over 125 Ton, over 60’ Boom 21 42,000 0.05 40 0.040 0.022 30 0.030 0.017 22 24 100
Barges (Used with Dredging)
Fuel or Water 20 90,000 0.05 20 0.021 0.011 20 0.021 0.011 18 20 60
Equipment or Work 20 90,000 0.05 20 0.021 0.011 20 0.021 0.011 18 20 60
Derrick 20 90,000 0.10 20 0.021 0.011 20 0.021 0.011 18 20 70
Anchor 20 90,000 0.05 20 0.021 0.011 20 0.021 0.011 18 20 60
Mooring Barge 20 90,000 0.05 20 0.021 0.011 20 0.021 0.011 18 20 60
Dump Scow 20 90,000 0.05 20 0.021 0.011 20 0.021 0.011 18 20 70

1
Sized by the largest bucket used (normally a mud bucket)
4-10
EP 1110-1-8, Vol. 2
30 Apr 14

Boats – See Category M10
Tugs and Tenders

(Used with Dredging)
Under 500 hp 8 18,000 0.10 80 0.083 0.045 70 0.072 0.039 32 38 80
501 through 1,000 hp 10 40,000 0.10 80 0.083 0.045 70 0.072 0.039 32 38 90
1,001 through 2,000 hp 15 55,000 0.10 80 0.083 0.045 70 0.072 0.039 32 38 100
2,001 through 3,000 hp 20 100,000 0.10 80 0.083 0.045 70 0.072 0.039 32 38 110
Over 3,000 hp 25 120,000 0.10 80 0.083 0.045 70 0.072 0.039 32 38 120
Pipeline and Accessories

(Inland Environment)
Metal Pipeline (under 20 inch)

Pumping Mud 2 9,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5
Pumping Sand 1 4,500 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5
Pumping Rock (Gravel) 0.3 1,500 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5
Joints 3 12,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 30
Pontoons/Floats 12 60,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5
Metal Pipeline (20 inch and

Larger)
Pumping Mud 3 12,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5
Pumping Sand 1.5 6,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5
Joints 3 12,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 30
Pontoons/Floats 12 60,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5
4-11
EP 1110-1-8, Vol. 2
30 Apr 14

Pipeline and Accessories

(Ocean Environment)
Metal Pipeline (All sizes)

Pumping Mud 2 9,000 0.40 0 0.000 0.000 0 0.000 0.000 0 0 5
Pumping Sand 1 4,500 0.40 0 0.000 0.000 0 0.000 0.000 0 0 5
Joints 1 4,500 0.40 0 0.000 0.000 0 0.000 0.000 0 0 5
Pontoons/Floats 2 9,000 0.40 0 0.000 0.000 0 0.000 0.000 0 0 5
Metal Pipeline On-Shore

Pumping Mud 3 12,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5
Pumping Sand 1.5 6,000 0.10 0 0.000 0.000 0 0.000 0.000 0 0 5
Standby Calculation: Standby for pipeline and accessories shall be based on pumping mud.

4-12
EP 1110-1-8, Vol. 2
30 Apr 14
Example: The piece of equipment shown is based on a known piece of equipment for
illustration purposes only.
USE THIS WORKSHEET TO COMPUTE A MONTHLY AND HOURLY RATE FOR MARINE
AND DREDGING PLANT
Region 02 ID No:
1. MARINE AND DREDGING PLANT INFORMATION AND EXPENSE FACTORS
a. Plant Pertinent Data:

(1) Equipment Description: 24" Hydraulic Cutter Suction Dredge
(2) Model and Series: Ellicott Series 4900 Super Dragon
(4) Acquisition Year: 1997
(5) Horsepower (hp) - Prime 3,730 hp
(6) Horsepower (hp) - Secondary Engine
(a) Electrical Generators 200 hp
(b) Hydraulic System 1,325 hp
(c) Cutter Head Drive 750 hp
(d) Hydraulic Water Jet 200 hp
Total Secondary hp 2,475 hp
(7) Plant Value:
(a) Acquisition Costs $4,500,000
(b) Capital Improvements $0
Total Plant Value $4,500,000
(8) Hours Worked per Month (Effective Time) 500 hrs/mo
(9) Additive Item(s) (Monthly Costs To be Estimated)

(a) Excessive Dredge Wear (Gravel) $8,000 /mo
(b) $0 /mo
(c) $0 /mo
(d) $0 /mo
(e) $0 /mo
Total Additive Items $8,000 /mo
b. Appendix B, Area Factors Data
(1) Labor Adjustment Factor (LAF) 1.02
(2) Fuel type Marine Diesel
Fuel Cost Per Gallon $3.11
(3) Cost of Money Rate (undiscounted) 2.125%
(4) Cost of Money Rate (discounted) 1.700%
c. Appendix E, Economic Index Data (EK 105)
(1) Economic Index, Acquisition Year 5429
(2) Economic Index, Present Year or Year of Use 8515
Input data, methodology and notes used in the following sections of this form are or have reference to EP 1110-1-8,
CONSTRUCTION EQUIPMENT OWNERSHIP AND EXPENSE SCHEDULE (see chapter 4).
Figure 4-2. Dredging Plant Ownership and Operating Rate Worksheet Page 1 of 4
4-13
EP 1110-1-8, Vol. 2
30 Apr 14
Region 02
1. MARINE AND DREDGING PLANT INFORMATION AND EXPENSE FACTORS (Continued)
d. Figure 4-1, Available Time to Dredge By Region Data (See Chapter 4, paragraph 4.3 for guidance)
(1) Months Available Per Year (9 months is used for this example) 9 months/yr
e. Table 4-1, Dredging Plant Cost Factors Data

(1) Useful Life (in Years) for Ownership (N) 25 yrs
(2) Physical Life (in Hours) for Repairs 130,000 hrs
(3) SLV (Salvage Value Factor) 0.10
(4) Prime Engine Fuel Factor (gal/bhp-hr) 0.045
(5) Secondary Engine Fuel Factor (gal/bhp-hr) 0.039
(6) WLS (Water, Lube & Supplies Factor) percent 22%
(7) RPR (Repair Cost Factor) 1.30
2. ANNUAL OWNERSHIP PERCENTAGE FACTORS
a. Depreciation Percent Per Year (DEPR)
1.0 - SLV / N
{1.e.(3)} {1.e.(1)}
1.0 - 0.10 / 25 yrs = 3.60% /yr
b. Facilities Capital Cost of Money Percent Per Year (FCCM)

Discounted Money
(N-1) x (1+SLV)+2 x Rate / 2N
{1.e.(1)} {1.e.(3)} {Appendix B} {1.e.(1)}
(25-1) x (1+ 0.10) + 2 x 1.700% / 50.00 = 0.97% /yr
c. Total Ownership Percent Per Year (DEPR + FCCM) = 4.57% /yr
3. OWNERSHIP COSTS
a. Ownership per Year

Total Ownership Percent Per Year
Plant Value x (DEPR + FCCM)
{1.a.(7)(a)} {2.c.}
$4,500,000 x 4.57% = $205,650.00 /yr
b. Monthly Ownership Expense
Ownership per Year / Months Available per Year

{3.a.} {1.d.(1)}
$205,650.00 /yr / 9 months/yr rounded = $22,850.00 /mo
4-14
EP 1110-1-8, Vol. 2
30 Apr 14
Region 02
4. OPERATING COSTS
a. Fuel Cost
(1) Prime Engine Fuel
Fuel Cost
Fuel Factor x HP x per Gallon
{1.e.(4)} {1.a.(5)} {1.b.(2)}
0.045 gal/bhp-hr x 3,730 x $3.11 = $522.01 /hr
(2) Secondary Engine Fuel

Fuel Cost
Fuel Factor x HP x per Gallon
{1.e.(5)} {1.a.(6)} {1.b.(2)}
0.039 gal/bhp-hr x 2,475 x $3.11 = $300.19 /hr
(3) Total Fuel (Prime Engine Fuel + Secondary Engine Fuel) = $822.20 /hr
b. Water, Lube, and Supply (WLS) Cost

(1) Prime Engine WLS
WLS Factor x Hourly Fuel Cost
{1.e.(6)} {4.a.(1)}
0.22 x $522.01 /hr = $114.84 /hr
(2) Secondary Engine WLS

WLS Factor x Hourly Fuel Cost
{1.e.(6)} {4.a.(2)}
0.22 x $300.19 /hr = $66.04 /hr
(3) Total Fuel (Prime Engine WLS + Secondary Engine WLS) = $180.88 /hr
c. Repair Cost
(1) Economic Adjustment Factor (EAF)

Economic Index for Economic Index
Present Year or for Acquisition
Year of Use / Year
{1.c.(2)} {1.c.(1)}
8515 / 5429 = 1.568
(2) Repair Cost
Total Plant
Value x RPR x EAF x LAF / Life in Hrs
{1.a.(7)} {1.e.(7)} {4.c.(1)} {1.b.(1)} {1.e.(2)}
$4,500,000 x 1.30 x 1.568 x 1.02 / 130,000 = $71.97 /hr
4-15
EP 1110-1-8, Vol. 2
30 Apr 14
Region 02
4. OPERATING COSTS (Continued)
d. Total Hourly Operating Cost (Fuel + WLS + Repairs)

Fuel + WLS + Repairs
{4.a.(3)} {4.b.(3)} {4.c.(2)}
$822.20 /hr + $180.88 /hr + $71.97 /hr = $1,075.05 /hr
e. Monthly Operating Cost
Total Hourly Hrs Worked per

Operating Cost x Mo
{4.d.} {1.a.(8)}
$1,075.05 /hr x 500 hrs/mo rounded = $537,525.00 /mo
5. TOTAL MONTHLY RATE
a. Ownership {3.b.} = $22,850.00 /mo
b. Operating {4.e.} = $537,525.00 /mo
c. Total Estimated Additive Items {1.a.(9))} = $8,000.00 /mo
d. TOTAL MONTHLY RATE = $568,375.00 /mo

{5.a.} + {5.b.} + {5.c.}
6. STANDBY ALLOWANCE
a. Standard Hourly Standby Expense

Maximum
Monthly hrs/mo = 30.4
Ownership days/mo x 24
Expense / hrs/day
{3.b.}
$22,850.00 /mo / 730 hrs/mo = $31.30 /hr
b. Generator Fuel Allowance for Dredge (An additional generator fuel allowance may be allowed
under certain circumstances. This allowance is applicable to dredges only.)
Total Secondary Secondary Fuel
Generator HP / HP x Cost
{1.a.(6)} {1.a.} {4.a.(2)}
200 hp / 2,475 hp x $300.19 = $24.26 /hr
c. TOTAL HOURLY STANDBY ALLOWANCE FOR DREDGE

Generator Fuel
Standby Expense + Allowance
{6.a.} {6.b.}
$31.30 /hr + $24.26 /hr = $55.56 /hr
4-16
EP 1110-1-8, Vol. 2
30 Apr 14
APPENDIX A
REFERENCES
SECTION I: REQUIRED PUBLICATIONS
Public Law 92-41. Renegotiation Act of 1971 [PL 92-41 (85 Stat. 97)].
Federal Acquisition Regulation 15.4 Contract Pricing, Government Printing Office,

Washington, DC.
. 30.101. Cost Accounting Standards, Part 30, Government Printing Office,

Washington, DC.
. 31.105. Construction and Architect-Engineer Contracts, Government Printing

Office, Washington, DC.
. 31.205-10. Cost of Money, Government Printing Office, Washington, DC.
. 31.205-36. Rental Costs, Government Printing Office, Washington, DC.
. 49. Termination of Contracts, Government Printing Office, Washington, DC.
. 52.230-2. Cost Accounting Standards, Government Printing Office,

Washington, DC.
Engineer Federal Acquisition Regulation Supplement (EFARS). 31.105 Construction

and Architect-Engineer Contracts, Regulation Supplement, Government Printing
Office, Washington, DC.
. 31.105-100. Contract Clause, Government Printing Office, Washington, DC.
Engineer Regulation 1110-2-1302. 2008. Engineering and Design - Civil Works Cost
Engineering, U.S. Army Corps of Engineers.
U.S. Department of Labor, Bureau of Labor Statistics. Producer Prices and Price
Indexes, Government Printing Office, Washington, DC.
SECTION II: RELATED PUBLICATIONS
. 2000. Caterpillar Performance Handbook, 31st ed, Peoria, Illinois.
. 2001. Caterpillar Performance Handbook, 32nd ed, Peoria, Illinois.
A-1
EP 1110-1-8, Vol. 2
30 Apr 14
. 2004. Caterpillar Performance Handbook, 34th ed, Peoria, Illinois.
. 2011. Caterpillar Performance Handbook, 41st ed, Peoria, Illinois.
. 2012. Caterpillar Performance Handbook, 42nd ed, Peoria, Illinois.
Caterpillar Tractor Company, Fundamentals of Earthmoving, Peoria, Illinois, 1975.
Energy Information Administration, Official Energy Statistics from the U.S. Government.
Electric Power Monthly, Washington, DC.
. Petroleum Marketing Monthly, Washington, DC.
Equipment Watch. 2006. Green Guide for Off-Highway Trucks and Trailers, San Jose,
California.
. 2006. Green Guide Volume I, San Jose, California.
. 2006. Green Guide Volume II, San Jose, California.
. 2006. Contractor’s Equipment Cost Guide.
. 2006. Cost Reference Guide.
Euclid, Inc. 1982. Euclid Hauler Handbook, 15th ed, Cleveland, Ohio.
Fiat-Allis Construction Machinery, Inc. 1983. Owning and Operating Costs, Springfield,
Illinois.
Goodyear Commercial Tire Systems Engineering Data Book

http://www.goodyeartrucktires.com/resources/publications.aspx.
Goodyear Engineered Products, Veyance Technologies,

http://www.goodyearep.com/productsDetail.aspx?id=4156.
A-2
EP 1110-1-8, Vol. 2
30 Apr 14
International Harvester, Pay Line Division. 1975. Earthmoving Principles, Schaumburg,

Illinois.
Koehring Company. 1981. Application Manual for Hydraulic Excavators and Shovels,
1st ed, Milwaukee, Wisconsin.
Mitchell Industrial Tire Company (MITCO), www.mitco.com.
Nichols, H L Jr. 2005. Moving the Earth, 5th ed, McGraw-Hill Professional; 5 edition
(March 28, 2005).
R S Means Company, Inc. 2013. Labor Rates for the Construction Industry, 40th ed.,
Kingston, Massachusetts.
Terex Corporation. 1981. Production and Cost Estimating of Material Movement with
Earthmoving Equipment, Hudson, Ohio.
TITAN Tire Corporation, Tire Catalog, http://www.titanstore.com/.
SECTION III: GEOGRAPHIC REGIONS

Engineer Pamphlet 1110-1-8 Construction Equipment Ownership and Operating
Expense Schedule, Volume 1
Volume 1 is for use in Region I, which includes the following states:
Connecticut New York

Maine Pennsylvania
Massachusetts Rhode Island
New Hampshire Vermont
New Jersey

Volume 2 is for use in Region II, which includes the following states:
Delaware Maryland
District of Columbia Michigan (Lower Peninsula)
Illinois (East of U.S. Highway 51) Ohio
Kentucky (East of U.S. Highway 51) Virginia
Indiana West Virginia
A-3
EP 1110-1-8, Vol. 2
30 Apr 14

Volume 3 is for use in Region III, which includes the following states:
Alabama Mississippi
Arkansas Missouri (Panhandle South of 36° -
Florida 30'00")
Georgia North Carolina
Louisiana South Carolina
Tennessee

Volume 4 is for use in Region IV, which includes the following states:
Iowa (North of U.S. Highway 20) North Dakota

Michigan (Upper Peninsula) South Dakota
Minnesota Wisconsin
Montana Wyoming

Volume 5 is for use in Region V, which includes the following states:
Colorado Kentucky (West of U.S. Highway 51)

Illinois (West of U.S. Highway 51) Missouri (North of 36° -30'00")
Iowa (South of U.S. Highway 20) Nebraska
Kansas

Volume 6 is for use in Region VI, which includes the following states:
A-4
EP 1110-1-8, Vol. 2
30 Apr 14
New Mexico Texas

Oklahoma

Volume 7 is for use in Region VII, which includes the following states:
Arizona Nevada
California Utah

Volume 8 is for use in Region VIII, which includes the following states:
Idaho Washington
Oregon
Volume 9 is for use in Region IX, which includes the following states:
Alaska

Volume 10 is for use in Region X, which includes the following states:
Hawaii

Volume 11 is for use in Region XI, which includes the following states:
Puerto Rico
A-5
EP 1110-1-8, Vol. 2
30 Apr 14

Volume 12 is for use in Region XII, which includes the following states:
Kwajalein Island
SECTION IV: USACE ACQUISITION INSTRUCTIONS
PART 31 – CONTRACT COST PRINCIPLES AND PROCEDURES

SUBPART 31.1 — APPLICABILITY
31.105-100 Construction and A-E Contracts.

In accordance with FAR 31.105(d)(2)(i)(b), equipment ownership and operating costs
shall be determined using EP 1110-1-8, Construction Equipment Ownership and
Operating Expense Schedule.
31.105-101 Special Contract Requirements.

The contracting officer shall insert the SCR, Equipment Ownership and Operating
Expense Schedule, in Section 00 73 00, in all solicitations and contracts for construction
within the United States that are expected to exceed the micro-purchase threshold.
Equipment Ownership and Operating Expense Schedule (MAR 1995)

(a) This special contract requirement does not apply to terminations. See 52.249-5000,
Basis for Settlement of Proposals, and FAR Part 49.
(b) Allowable cost for construction and marine plant and equipment in sound workable
condition owned or controlled and furnished by a contractor or subcontractor at any tier
shall be based on actual cost data for each piece of equipment or groups of similar
serial and series for which the Government can determine both ownership and
operating costs from the contractor's accounting records. When both ownership and
operating costs cannot be determined for any piece of equipment or groups of similar
serial or series equipment from the contractor's accounting records, costs for that
equipment shall be based upon the applicable provisions of EP 1110-1-8, Construction
Equipment Ownership and Operating Expense Schedule, Region [insert Roman
numeral for the appropriate region of the schedule]. Working conditions shall be
considered to be average for determining equipment rates using the schedule unless
specified otherwise by the contracting officer. For equipment not included in the
schedule, rates for comparable pieces of equipment may be used or a rate may be
A-6
EP 1110-1-8, Vol. 2
30 Apr 14
developed using the formula provided in the schedule. For forward pricing, the
schedule in effect at the time of negotiations shall apply. For retroactive pricing, the
schedule in effect at the time the work was performed shall apply.
(c) Equipment rental costs are allowable, subject to the provisions of FAR 31.105(d)(ii)
and FAR 31.205-36, Rental Costs. Rates for equipment rented from an organization
under common control, lease-purchase arrangements, and sale-leaseback
arrangements, will be determined using the schedule, except that actual rates will be
used for equipment leased from an organization under common control that has an
established practice of leasing the same or similar equipment to unaffiliated lessees.
SECTION IV: USACE ACQUISITION INSTRUCTIONS (Continued)
(d) When actual equipment costs are proposed and the total amount of the pricing
action exceeds the SAT, the contracting officer shall request the contractor to submit
either certified cost or pricing data, or partial/limited data, as appropriate. The data
shall be submitted on Standard Form 1411, Contract Pricing Proposal Cover Sheet.
SECTION V: EFAR REFERENCE
The Engineer Federal Acquisition Regulation Supplement (EFARS) is RESCINDED by

the USACE Acquisition Instruction which was issued by USACE Head of Contracting
Activity on March 18, 2013. EFARS can be referenced, as necessary, for any contracts
issued before March 18, 2013.
EFARS PART 31 - CONTRACT COST PRINCIPLE AND PROCEDURES
SUBPART 31.1 -- APPLICABILITY
31.105 Construction and Architect-Engineer Contracts.
(d)(2)(i)(b) In this case, equipment ownership and operating costs shall be

determined using the Construction Equipment Ownership and Operating Expense
Schedule published by the U.S. Army Corps of Engineers.
31.105-100 Contract Statement.
The contracting officer shall insert the statement at 52.231-5000 in all

solicitations and contracts for construction within the United States that are expected to
exceed the small purchase threshold.
A-7
EP 1110-1-8, Vol. 2
30 Apr 14
EFARS Clause - 52.231-5000 Equipment Ownership and Operating Expense

Schedule.
As prescribed in 31.105-100, insert the following clause in all solicitations and

contracts for construction that are expected to exceed the small purchase threshold.
EQUIPMENT OWNERSHIP AND OPERATING EXPENSE SCHEDULE (MAR

1995) – EFARS.
(a) This clause does not apply to terminations. See 52.249-5000, Basis for
Settlement of Proposals, and FAR Part 49, Termination of Contracts.
(b) Allowable cost for construction and marine plant and equipment in sound
workable condition owned or controlled and furnished by a contractor or subcontractor
at any tier shall be based on actual cost data for each piece of equipment or groups of
similar serial and series for which the Government can determine both ownership and
operating costs from the contractor’s accounting records. When both ownership and
operating costs cannot be determined for any piece of equipment or groups of similar
serial or series equipment from the contractor’s accounting records, costs for that
equipment shall be based upon the applicable provisions of EP 1110-1-8, Construction
Equipment Ownership and Operating Expense Schedule, Region [Insert roman numeral
for the appropriate region of the schedule]. Working conditions shall be considered to
be average for determining equipment rates using the schedule unless specified
otherwise by the contracting officer. For equipment not included in the schedule, rates
for comparable pieces of equipment may be used or a rate may be developed using the
formula provided in the schedule. For forward pricing, the schedule in effect at the time
of negotiations shall apply. For retroactive pricing, the schedule in effect at the time the
work was performed shall apply.
(c) Equipment rental costs are allowable, subject to the provisions of FAR
31.105, Construction and Architect-Engineer Contract, and FAR 31.205-36, Rental
Costs. Rates for equipment rented from an organization under common control, lease-
purchase arrangements, and sale-leaseback arrangements, will be determined using
the schedule, except that actual rates will be used for equipment leased from an
organization under common control that has an established practice of leasing the same
or similar equipment or unaffiliated lessees.
(d) When actual equipment costs are proposed and the total amount of the
pricing action exceeds the small purchase threshold, the contracting officer shall
request the contractor to submit either certified cost or pricing data, or partial/limited
A-8
EP 1110-1-8, Vol. 2
30 Apr 14
data, as appropriate. The data shall be submitted on Standard Form 1411, Contract
Pricing Proposal Cover Sheet.
SECTION VI. OBTAINING PUBLICATION AND CHECKRATE
The Engineer Pamphlet (EP) 1110-1-8 Volumes 1-12 is available in portable document
format (PDF) and can be viewed or downloaded at the official HQUSACE documents
webpage at http://www.usace.army.mil/ by selecting "Library" and selecting
"Publications". The direct link to the current edition is:
http://publications.usace.army.mil/publications/eng-pamphlets/EP_1110-1-8/toc.html.
Compact disks (CDs) are developed and distributed to a pre-publication mailing list, a
limited number of additional CDs are produced and available upon request.
Requests for CDs may be placed by sending an e-mail to CENWW-

COST@usace.army.mil. When ordering, please give the following information and
specify the quantity:
Title of Publication: EP 1110-1-8, Construction Equipment Ownership and

Operating Expense Schedule
Region: Region I through XII
Volume No. Volume No. 1 through No. 12
Media: CD
Quantities:
Other Products are available at the Walla Walla District Cost Engineering website:
http://www.nww.usace.army.mil/Missions/CostEngineering.aspx. Expand the Product
Support Section by clicking on the plus sign next to “Construction Equipment Rates (EP
1110-1-8) and CHECKRATE”, the following links and downloads are available:
Previous editions of Engineers Pamphlet EP1110-1-8 are available at:

http://www.nww.usace.army.mil/Missions/CostEngineering/Historical.aspx.
To download the CHECKRATE workbook the direct link is:

http://www.nww.usace.army.mil/Portals/28/docs/costengineering/CheckRate04v06r1.xls.
A-9
EP 1110-1-8, Vol. 2
30 Apr 14
Use this worksheet to compute rates for equipment that is not in this pamphlet.
ID No.:
(1) Equipment Description:
(2) Model and Series:
(3) Year of Use:
(4) Year Manufactured:
(5) Horsepower - Equipment:
(6) Horsepower - Carrier:
(7) Fuel type: - Equipment: gas/diesel off-road/diesel on-road/electric/air
- Carrier: gas/diesel off-road/diesel on-road/electric/air
(8) Shipping Weight (cwt):
(9) Tire size and number of tires: (Cost of tires based on year of use – see 1.a.(3) and
appendix F)
No. Size/Ply Unit Price Cost

(a) Front (FT): $ $
(b) Drive (DT): $ $
(c) Trailing (TT): $ $
(d) Total Tire Cost: $
b. Category and Subcategory Number:

(1) Economic Key (EK):
(2) Condition (C): Average or Severe or Difficult
(3) Discount Code (DC): B = 7.5% (0.075) – or – S = 15.0% (0.15)
(4) Life in Hours (LIFE):
(5) Salvage Value Percentage (SLV):
(6) Fuel Factor – Equipment [Electric (E) Gas (G) Diesel (D)]:
(7) Fuel Factor – Carrier (E G D):
(8) Filters, Oil, and Grease (FOG) Factor (E G D):
(a) Front (FT):
(b) Drive (DT):
(c) Trailing (TT):
(10) Repair Cost Factor (RCF):
Equipment Rate Computation Worksheet (copy as needed). Page 1 of 6
A-10
EP 1110-1-8, Vol. 2
30 Apr 14
2. EQUIPMENT VALUE
a. List Price + Accessories: [at Year of Manufacture] =$
(1) Discount: (List Price + Accessories) x (Discount Code)

[1.c.(3)]
($ +$ )x( ) =-($
(2) Subtotal [2.a.] – [2.a.(1)] Subtotal=$
(3) Sales or Import Tax: (Subtotal) x (Tax Rate)

[2.a.(2)] [Appendix B]
($ )x( ) =+$
(4) Total Discounted Price: Subtotal: [2.a.(2)] + [2.a.(3)] Subtotal=$
b. Freight: (Shipping Weight) x (Freight Rate per cwt)

[1.a.(8)] [Appendix B]
( cwt) x ($ /cwt) =+$
c. TOTAL EQUIPMENT VALUE (TEV): TOTAL[2.]:=$

[(2.a.(4)] + [(2.b)]
a. (LIFE hours (hr)) / (Working Hours Per Year (WHPY)) = N

[1.c.(4)] [Appendix B]
( hr) / ( hr/yr) =
4. OWNERSHIP COST
a. Depreciation

(Tire Index, Yr of Mfg) / (Tire Index, Based on 1.a.(3)) = Tire Cost Index (TCI)
[Appendix E, EK=100] [Appendix E, EK=100]
( )/( ) = (TCI)
(2) [(TEV) x [1.0 - ( SLV )] - [ ( TCI ) x (Tire Cost)]] / ( LIFE )

[2.c.] [1.c.(5)] [4.a.(1)] [1.a.(9)(d)] [1.c.(4)]
[($ ) x [1.0 – ( )] – [( ) x ($ )]] / ( hr)
=$ /hr
A-11
EP 1110-1-8, Vol. 2
30 Apr 14
(1) [[( N ) - 1.0] x [1.0 + (SLV)] + 2.0] / [2.0x ( N )] = Avg Value Factor
[3.a.] [1.c.5.] [3.a.] (AVF)
[[( yr) – 1.0] x [1.0 + ( )] + 2.0] / [2.0 x ( yr)]
= (AVF)
(2) ( TEV ) x ( AVF ) x (Adjusted Cost - of - Money) / ( WHPY )

[2.c] [4.b.(1)] [Appendix B] [Appendix B]
($ )x( )x( )/( hr/yr)

=$ /hr
c. TOTAL HOURLY OWNERSHIP COST: TOTAL [4.]: =$ /hr

[4.a.(2)] + [4.b.(2)]
5. OPERATING COST
a. Fuel Costs:
(1) Equipment:
(Fuel Factor x (Horsepower (hp)) x (Fuel Cost Per Gallon (gal))

[1.c.(6)] [1.a.(5)] [Appendix B]
( )x( hp) x ($ / gal) =$ /hr
(2) Carrier:
(Fuel Factor) x (Horsepower) x (Fuel Cost Per Gallon)

[1.c.(7)] [1.a.(6)] [Appendix B]
( )x( hp) x ($ /gal) =$ /hr
(3) Total Hourly Fuel Cost: Total [5.a.] =$ /hr

[(5.a.(1)] + [5.a.(2)]
b. FOG Cost:
(1) Equipment:
(FOG Factor) x (Equipment Fuel Cost) x (Labor Adjustment Factor (LAF))

[1.c.(8)] [5.a.(1)] [Appendix B]
( ) x ($ /hr) x ( ) =$ /hr
A-12
EP 1110-1-8, Vol. 2
30 Apr 14
(2) Carrier:
(FOG Factor) x (Carrier Fuel Cost) x (LAF)

[1.c.(8)] [5.a.(2) [Appendix B]
( ) x ($ /hr) x ( ) =$ /hr
(3) Total Hourly FOG Cost: Total [5.b.] =$ /hr

[(5.b.(1)] + [5.b.(2)]
c. Alternative Fuel/FOG Cost: Total [5.c.] =$ /hr

(See chapter 2, paragraph 24.d. for guidance on when to use.)
d. Repair Cost:

(EK is from [1.c.(1)])
(Economic Index for Year 1.a.(3)) / (Economic Index for Year 1.a.(4))
[Appendix E] [Appendix E]
( )/( ) = (EAF)
(RCF) x (EAF) x (LAF) = Repair Factor (RF)

[1.c.(10)] [5.d.(1)] [Appendix B]
( )x( )x( ) = (RF)
(3) Repair Cost:
[(TEV) - [(TCI) x (Tire Cost )]] x (RF) / (LIFE)

[2.c.] [4.a.(1)] [1.a.(9)(d)] [5.d.(2)] [1.c.(4)]
[($ ) – [( ) x ($ )]] x ( )/( )
(4) Total Hourly Repair Cost: Total [5.d.] =$ /hr
A-13
EP 1110-1-8, Vol. 2
30 Apr 14
e. Tire Wear Cost: (Use current price levels. See Appendix F)
[1.5 x (FT Cost)] / [1.8 x (FT Wear Factor) x (Maximum Tire Life Hours)]
[1.a.(9)(a)] [1.c.(9)(a)] [Appendix F]
[1.5 x ($ )] / [1.8 x ( )x( /hr)]
=$ /hr
[1.5 x (DT Cost)] / [1.8 x (DT Wear Factor) x (Maximum Tire Life Hours)]
[1.a.(9)(b)] [1.c.(9)(b)] [Appendix F]
[1.5 x ($ )] / [1.8 x ( )x( /hr)]
=$ /hr
[1.5 x (TT Cost)] / [1.8 x (TT Wear Factor) x (Maximum Tire Life Hours)]
[1.a.(9)(c)] [1.c.(9)(c)] [Appendix F]
[1.5 x ($ )] / [1.8 x ( )x( /hr)]
=$ /hr
(4) Total Tire Wear Cost: Total [5.e.] =$ /hr

[Sum 5.e.(1) through 5.e.(3)]
(Total Tire Wear Cost) x 0.15 x (LAF)

[5.e.(4)] [Appendix B]
($ /hr) x 0.15 x ( ) Total [5.f.] =$ /hr
g. TOTAL HOURLY OPERATING COST: TOTAL [5.] =$ /hr

[Sum 5.a. through 5.f.]
A-14
EP 1110-1-8, Vol. 2
30 Apr 14
6. HOURLY RATES
(Ownership Cost) + (Operating Cost)
($ /hr) + ($ /hr) =$ /hr

[(Depreciation) + [(FCCM) x (40 hr/wk) / (Work hr/wk)] + (Operating Cost)]

[4.a.(2)] [4.b.(2)] (example: 60 hr/wk) [5.g.]
[($ /hr) + [($ /hr) x (40 hr/wk) / ( hr/wk)] + ($ /hr)]
=$ /hr
[(Depreciation) x 0.50] + (FCCM)

[4.a.(2)] [4.b.(2)]
[($ /hr) x 0.50] + ($ /hr) =$ /hr)
A-15
EP 1110-1-8, Vol. 2
30 Apr 14
A-16
EP 1110-1-8, Vol. 2
30 Apr 14
EP 1110-1-8
APPENDIX B
(Vol. 2)
AREA FACTORS 4/30/2014
MIDEAST
Region: 2
Total State Sales or Import Tax Rate: 6.00%

Working Hours Per Year (WHPY): 1,450 hrs/yr
Labor Adjustment Factor (LAF): 1.02
Electricity Cost Per Kilowatt-Hour: $0.095 /kW-Hr
Gasoline Cost Per Gallon: $3.76 /gal
Diesel Cost Per Gallon (Off-Road Use): $3.49 /gal
Diesel Cost Per Gallon (On-Road Use): $4.05 /gal
Cost-of-Money Rate (Full Rate): 2.125%
Cost-of-Money Rate (Adjusted): 1.700%
Freight Rates
over 0 cwt thru 240 $10.54

over 800 cwt thru 99,999 $8.64
B-1
B-1
EP 1110-1-8, Vol. 2
30 Apr 14
EP 1110-1-8 APPENDIX B
(Vol. 1)
4/30/2014 AREA FACTORS (for all regions)
Below is a listing of all regional area factors for reference only. The area factor's used for this pamphlet are located on previous page B-1.
Freight Cost
Reg SST WHPY LAF Elec Gas D-Off D-On Thru CWT $ Thru CWT $ Thru CWT $ Thru CWT $ Thru CWT $ Thru CWT $ Thru CWT $
1 NORTHEAST 2014 6.00% 1360 1.15 $0.132 $3.77 $3.66 $4.19 240 $19.34 300 $17.80 400 $15.56 500 $13.43 700 $6.79 800 $6.79 99,999 $11.41
2 MIDEAST 2014 6.00% 1450 1.02 $0.095 $3.76 $3.49 $4.05 240 $10.54 300 $9.81 400 $8.84 500 $7.94 700 $5.17 800 $5.17 99,999 $8.64
3 SOUTHEAST 2014 8.60% 1530 0.88 $0.095 $3.62 $3.42 $3.89 240 $16.27 300 $14.82 400 $12.69 500 $10.64 700 $5.85 800 $5.85 99,999 $9.79
4 NORTHCENTRAL 2014 5.85% 1260 1.02 $0.094 $3.75 $3.49 $4.00 240 $22.71 300 $20.99 400 $18.72 500 $16.62 700 $12.23 800 $12.14 99,999 $7.90
5 MIDWEST 2014 7.90% 1400 0.98 $0.089 $3.82 $3.44 $3.94 240 $17.09 300 $15.69 400 $13.80 500 $12.05 700 $9.02 800 $8.99 99,999 $7.36
6 SOUTHWEST 2014 8.70% 1590 0.86 $0.086 $3.65 $3.43 $3.86 240 $22.74 300 $21.12 400 $19.04 500 $17.14 700 $12.49 800 $12.45 99,999 $8.14
7 WEST 2014 9.25% 1630 1.12 $0.105 $3.83 $3.49 $4.05 240 $36.13 300 $33.56 400 $30.18 500 $27.08 700 $18.40 800 $17.53 99,999 $10.93
8 NORTHWEST 2014 6.05% 1540 1.06 $0.078 $3.85 $3.54 $4.07 240 $30.86 300 $29.05 400 $26.59 500 $24.30 700 $11.26 800 $9.51 99,999 $6.48
9 ALASKA 2014 4.40% 1040 1.19 $0.155 $4.36 $3.87 $4.11 240 $63.98 300 $53.95 400 $43.11 500 $49.09 700 $33.08 800 $31.15 99,999 $27.79
10 HAWAII 2014 4.50% 1480 1.23 $0.341 $4.39 $4.15 $4.90 240 $118.93 300 $71.52 400 $56.01 500 $61.76 700 $43.92 800 $48.92 99,999 $22.55
11 PUERTO RICO 2014 7.00% 1560 0.7 $0.312 $3.86 $3.47 $3.95 240 $42.12 300 $30.96 400 $26.95 500 $24.52 700 $17.75 800 $16.52 99,999 $12.22
12 KWAJALEIN 2014 4.50% 1390 1 $0.341 $4.00 $4.15 $4.90 240 $33.40 300 $31.19 400 $28.13 500 $25.24 700 $12.23 800 $10.61 99,999 $8.09
SST = State Sales tax WHPY = Work Hours Per Year LAF B-
= Labor
2 Adjustment Factor Elec = Electricty Cost Per kW-Hr
Gas = Gasoline Cost per Gal D-Off = Diesel-Off Road Cost per Gal D-On = Diesel-On Road Cost per Gal CWT = Hundred Pounds
B-2
EP 1110-1-8, Vol. 2
30 Apr 14
APPENDIX C
GUIDE FOR SELECTING OPERATING CONDITIONS
EQUIPMENT TYPE AVERAGE SEVERE

B25 and B35:
Buckets Working in gravels, silts, Working in rock, hard
Clamshell or and sands at low impact digging, high impact, or
Dragline freshwater environment. saltwater environment.
Depreciation Period: 8,000 - 10,000 hours 6,500 - 8,000 hours
C80 and C90:

Cranes Lift less than rated capacity, Continuous lift near rated
Hydraulic, Truck intermittent duty. capacity, excessive swing,
Mounted abrasive materials, sloped
Mechanical, Truck surfaces, and saltwater
Mounted environment.
C85:
Cranes Gravels, silts, pull, and lift Highly abrasive materials,
Mechanical Dragline, less than rated capacity. impact breakout,
Lifting, or Clamshell continuous load near rated
capacity, and saltwater
Crawler Mounted environment.
G10:
Generators Working below rated Working at or above rated
capacity, good field capacity, poor field
conditions. conditions, such as
saltwater.
C-1
EP 1110-1-8, Vol. 2
30 Apr 14

G15:
Graders, Motor Haul road maintenance; Maintenance of hard-
road construction, ditching; packed roads with
loose fill spreading; embedded rock; heavy fill
landforming, landleveling; spreading; ripping
summer road maintenance scarifying of asphalt or
with medium to heavy concrete; continuous high
winter snow removal; and load factor; and high
elevating grader use. impact.
Depreciation Period: 14,500 hours 13,500 hours
H25:
Hydraulic Excavators Mass excavation or Continuous trenching or
Crawler Mounted trenching where machine truck loading in rock or shot
digs all the time in natural rock soils; large amount of
bed clay soils; some travel over rough ground;
traveling and steady, full machine continuously
throttle operation; and most working on rock floor with
log loading operations. constant high load factor
and high impact; and
saltwater environment.
Depreciation Period: 8,500 - 19,000 hours 7,000 – 15,000 hours
H30:
Hydraulic Excavators Continuous digging in Continuous digging in
Wheel Mounted sandy clay/sandy gravel, rock/natural bed clay, high
site development, and impact, using hammer, and
lumber yard applications. working in forests or
quarries.
C-2
EP 1110-1-8, Vol. 2
30 Apr 14

H35:
Hydraulic Shovels Continuous loading in well Continuous loading in
Crawler Mounted shot rock or fairly tight poorly shot rock, virgin, or
(nonelectric) bank. Good underfoot lightly blasted tight banks.
conditions: dry floor, little Adverse underfoot
impact, or sliding on conditions: rough floors,
undercarriage. high impact sliding on
undercarriage; and
L10:
Land Clearing Equipment Working in low impact High impact conditions
conditions at or below rated working at or above rated
capacity. capacity.
L30:
Loaders, Belt (conveyors) Working below rated Working at or above rated
capacity, with intermittent capacity with continuous
service. service.
L35:
Loaders, Front End Bank excavation, Loading shot rock, cobbles,
Crawler Type intermittent ripping, glacial till, and caliche; steel
basement digging of natural millwork; high density
bed clays, sands, silts, and materials in standard
gravels; some traveling; bucket; continuous work on
and steady full throttle rock surfaces; large amount
operations. of ripping of tight rock
materials; high impact
conditions; and saltwater
environment.
C-3
EP 1110-1-8, Vol. 2
30 Apr 14

L40:
Loaders, Front End Continuous truck loading Loading shot rock (large
Wheel Type from stockpile; low to loaders); handling high
(does not include medium density materials in density materials with
skid steer and tool properly sized bucket; counterweighted machine;
carriers) hopper charging in low to steady loading from very
medium rolling resistance; tight banks; continuous
loading from bank in good work on rough or very soft
digging; and load and carry surfaces; load and carry in
on poor surfaces and slight hard digging; travel longer
adverse grades. distances on poor surfaces
with adverse grades and
L45 and L50:

Loaders with Backhoe Utility applications in Production applications or
Crawler Type and medium to heavy soil; digging in rock; regular use
Wheel Type occasional use of constant of constant flow
flow implements and dig implements; and dig depths
depths to 3.05 meters over 3.05 meters (10 feet).
(10 feet).
L60:
Log Skidders Continuous turning, steady Continuous turning, steady
skidding for medium skidding for long distances
distances with moderate with frequent decking; poor
decking. Good underfoot conditions: wet
underfooting: dry floor with floor, steep slopes, and
few stumps and gradual numerous stumps; and
rolling terrain. saltwater environment.
C-4
EP 1110-1-8, Vol. 2
30 Apr 14

M10 - .31 and .32:
Clamshell dredges Gravel, silts, breakout force Rock, abrasive materials,
< 5 cy at less than capacity, load at rated capacity,
Amphibious Excavator freshwater conditions. saltwater conditions.
M10 - .51 and .53:

Boats, Skiffs, Crew Freshwater applications, Saltwater use, medium to
Boats, Work Boats, light waves, and steady to high waves, heavy use.
Survey Boats, and light use.
Launches
P35:
Pipelayers Typical pipelayer use in Continuous use in deep
operating conditions mud or water or on rock
ranging from very good to surfaces.
severe.
R10:
Rippers and Bank Slopers Light rock, medium Hard rock, excessive wear
breakout force required. due to high breakout force.
S10, S15, S20, and S25:

Scrapers Varying loading and haul High impact conditions,
Self-Propelled road conditions; long and such as loading ripped
Tractor Drawn short hauls; adverse and rock; overloading,
Soil Stabilizers favorable grades; some continuous high total
impact; and typical road- resistance conditions; and
building use on a variety of rough haul roads.
jobs.
C-5
EP 1110-1-8, Vol. 2
30 Apr 14

T15:
Tractors Production dozing in clays, Heavy rock ripping; tandem
Crawler (Dozer) sands, gravels, and talus ripping; pushloading and
rock. Push-loading dozing in hard rock; work
scrapers, borrow pit ripping, on rock surfaces;
most land clearing and continuous high impact
skidding applications. conditions; and saltwater
Medium impact conditions. environment.
Production landfill work.
T20:
Tractors Production dozing, push Production dozing in rock;
Wheel Type (Dozer) loading in clays, sands, push loading in rocky,
silts, loose gravels; and boulder strewn borrow pits;
shovel cleanup. high impact conditions; and
landfill compactor work.
T30:
Trenchers Working in sands and silts Working in gravels and
Chain and Wheel Type below rated capacity of the abrasive materials at or
machine. above the rated capacity of
the machine.
T45 and T50:

Truck Trailers Varying loading and road Consistently poor road
Trucks, Highway conditions; and typical conditions; and oversized
construction use on a loading equipment.
variety of jobs.
C-6
EP 1110-1-8, Vol. 2
30 Apr 14

T55 and T60:
Truck, Off-Highway Varying load and haul road Continuous use on very
Trucks, Water, conditions; high rolling poorly maintained haul
Off-Highway resistance and poor traction roads, high rolling
(Articulated and Rigid) during part of the job; some resistance, and poor
adverse grades; some traction; frequent adverse
impact loads; and typical grades and high impact
use in road building, dam loads; and poorly matched
construction, open-pit loading equipment with
mining, etc. continuous overloading.
W10 and W15:

Wagons Varying load and haul road Continuous use on very
Bottom Dump conditions; long and short poorly maintained haul
Rear Dump hauls; high rolling roads, high rolling
resistance and poor traction resistance, and poor
during part of the job; some traction; high impact
adverse grades; some conditions, such as loading
impact; typical road building ripped rock; frequent
use in a variety of jobs; and adverse grades and high
dam construction, open-pit impact loads; and poorly
mining, etc. matched loading equipment
with continuous
overloading.
C-7
EP 1110-1-8, Vol. 2
30 Apr 14
C-8
EP 1110-1-8,
EPVol. 2
1110-1-8
30 Apr(Vol.
14 1)
4/30/2014
APPENDIX D
EQUIPMENT HOURLY CALCULATION FACTORS
EQUIPMENT CARRIER FOG TIRE WEAR
CATEGORY
FUEL FACTORS FUEL FACTORS FACTORS FACTORS
SUB DESCRIPTION EK C DC LIFE SLV HPF E G D HPF E G D E G D FT DT TT RCF
A10 0.00 AGGREGATE / CHIP SPREADERS 1

A10 0.10 SELF-PROPELLED 10 A B 8,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .000 .102 .102 0.83 0.72 0.92 0.75
A10 0.20 TOWED & TAILGATE 10 A B 6,000 0.20 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.73 0.00 0.82 0.60
A15 0.00 AIR COMPRESSORS, PORTABLE 1
A15 0.10 ROTARY SCREW 5 A B 10,000 0.20 75 .750 .068 .036 0 .000 .000 .000 .477 .136 .119 0.66 0.00 0.73 0.75
A15 0.20 SHOP TYPE 5 A B 12,000 0.15 75 .750 .068 .036 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.65
A20 0.00 AIR HOSE, TOOLS & EQUIPMENT 1
A20 0.10 AIR DRILL HOSE 5 A B 3,500 0.05 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 1.50
A20 0.20 SANDBLAST HOSE 5 A B 3,500 0.05 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 1.65
A20 0.30 SANDBLASTERS, BREAKERS, & MISC. AIR TOOLS 5 A B 6,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 0.96 0.84 1.07 1.50
A25 0.00 ASPHALT PAVING DISTRIBUTORS 10 A B 6,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .119 0.96 0.63 1.07 0.85
A30 0.00 ASPHALT PAVERS & MISCELLANEOUS ROAD 1
EQUIPMENT
A30 0.10 SELF PROPELLED 10 A B 8,000 0.15 70 .700 .063 .034 0 .000 .000 .000 .000 .136 .119 1.08 0.72 1.20 1.00
A30 0.20 TOWED 10 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .119 1.08 0.00 1.20 0.80
A30 0.30 SLURRY SEAL PAVERS (Cold mix) 10 A B 12,000 0.20 60 .600 .054 .029 13 .130 .012 .006 .000 .100 .100 1.08 0.71 1.20 0.55
A30 0.40 MISCELLANEOUS ROAD EQUIPMENT 10 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .119 1.08 0.71 1.20 0.80
A35 0.00 ASPHALT PAVING KETTLES 10 A B 6,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .119 1.08 0.71 1.20 0.80
A40 0.00 ASPHALT & CONCRETE MILLERS / PROFILERS / 10 A B 6,000 0.20 95 .950 .086 .045 0 .000 .000 .000 .000 .136 .119 1.08 0.71 1.20 1.00
PLANERS / ROTARY GRINDERS
A45 0.00 ASPHALT RECYCLERS & SEALERS 10 A B 5,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .119 1.08 0.71 1.20 0.90
B10 0.00 BATCH PLANTS, ASPHALT & CONCRETE 1
B10 0.10 ASPHALT 10 A B 8,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 1.08 0.72 1.20 1.00
EK=Economic Key (Appendix E) LIFE=Economic Life E=Electric Powered FT=Front Tire

C=Operating Conditions (A=average, S=severe) D- 1
SLV=Salvage Value G=Gas Powered DT=Drive Tire
DC=Discount Code (B=basic 7.5%, S=special 15%) HPF=Horsepower Factor D=Diesel Powered TT=Trailing Tire
RCF=Repair Cost Factor
D-1
EP 1110-1-8, Vol. 2
EP 1110-1-8
(Vol.30
1) Apr 14
4/30/2014
APPENDIX D
CATEGORY
B10 0.20 CONCRETE 10 A B 8,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 1.08 0.71 1.20 1.00
B10 0.30 PUGMILL 10 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 1.08 0.71 1.20 1.00
B15 0.00 BROOMS, STREET SWEEPERS & FLUSHERS 95 A B 8,000 0.10 65 .650 .059 .031 13 .130 .012 .006 .000 .102 .119 0.96 0.63 1.07 0.80
B20 0.00 BRUSH CHIPPERS 95 A B 8,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .119 0.00 0.00 0.92 0.90
B25 0.00 BUCKETS, CLAMSHELL 15 A B 8,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.70
B25 0.00 BUCKETS, CLAMSHELL 15 S B 6,500 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.80
B30 0.00 BUCKETS, CONCRETE 1
B30 0.10 GENERAL PURPOSE, MANUAL TRIP 15 A B 8,000 0.05 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.70
B30 0.20 LAYDOWN 15 A B 8,000 0.05 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.75
B30 0.30 LOWBOY 15 A B 8,000 0.05 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.80
B30 0.40 LOW SLUMP 15 A B 8,000 0.05 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.80
B35 0.00 BUCKETS, DRAGLINE 1
B35 0.10 LIGHT WEIGHT 15 A B 8,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.70
B35 0.10 LIGHT WEIGHT 15 S B 6,500 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.80
B35 0.20 MEDIUM WEIGHT 15 A B 9,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.70
B35 0.20 MEDIUM WEIGHT 15 S B 7,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.80
B35 0.30 HEAVY WEIGHT 15 A B 10,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.70
B35 0.30 HEAVY WEIGHT 15 S B 8,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.80
C05 0.00 CHAIN SAWS 95 A B 2,000 0.10 90 .900 .081 .043 0 .000 .000 .000 .477 .136 .161 0.00 0.00 0.00 2.50
C10 0.00 COMPACTORS, WALK-BEHIND OR REMOTE 1
CONTROLLER
C10 0.10 COMPACTORS, RAMMERS / TAMPERS & 95 A B 4,000 0.05 90 .900 .081 .043 0 .000 .000 .000 .477 .102 .102 0.00 0.00 0.00 1.20
VIBRATORY PLATES

D-2
EP 1110-1-8,
EPVol. 2
1110-1-8
30 Apr(Vol.
14 1)
4/30/2014
APPENDIX D
CATEGORY
C10 0.20 ROLLERS, VIBRATORY 95 A B 4,000 0.15 90 .900 .081 .043 0 .000 .000 .000 .477 .102 .102 0.00 0.00 0.00 1.20
C15 0.00 CONCRETE CLEANERS / ABRASIVE BLASTERS 1 A
C15 0.10 WALK BEHIND 95 A B 4,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .530 .136 .119 0.00 0.00 0.00 0.90
C15 0.20 TRUCK/TRAILER MOUNTED 95 A B 8,000 0.20 95 .950 .086 .045 50 .500 .045 .024 .000 .136 .119 0.72 0.66 0.79 0.90
C20 0.00 CONCRETE BUGGIES 95 A B 4,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .530 .136 .119 0.96 0.63 1.07 0.70
C25 0.00 CONCRETE FINISHERS/SCREEDS/SPREADERS 1
C25 0.10 FINISHERS/TROWELS 95 A B 5,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .530 .136 .119 0.00 0.00 0.00 0.80
C25 0.20 VIBRATORY SCREED 95 A B 5,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .530 .136 .119 0.96 0.84 1.07 0.80
C25 0.25 VIBRATORY LASER SCREED 95 A B 8,000 0.30 65 .650 .059 .031 0 .000 .000 .000 .000 .180 .160 0.96 0.84 1.07 0.60
C25 0.30 MATERIAL/TOPPING SPREADERS 95 A B 8,000 0.30 65 .650 .059 .031 0 .000 .000 .000 .000 .180 .160 0.96 0.84 1.07 0.60
C30 0.00 CONCRETE GRINDERS 95 A B 5,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .530 .136 .119 0.00 0.00 0.00 0.90
C35 0.00 CONCRETE GUNITERS / SHOTCRETERS 95 A B 7,000 0.25 75 .750 .068 .036 0 .000 .000 .000 .477 .136 .119 0.96 0.86 1.07 0.90
C40 0.00 CONCRETE MIXING UNITS 95 A B 5,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .530 .136 .119 0.00 0.00 0.92 0.80
C45 0.00 CONCRETE PAVING MACHINES 10 A B 6,000 0.20 75 .750 .068 .036 0 .000 .000 .000 .000 .136 .119 1.08 0.72 1.20 1.00
C55 0.00 CONCRETE PUMPS 95 A B 8,000 0.10 70 .700 .063 .034 10 .100 .009 .005 .477 .136 .119 0.96 0.86 1.07 1.00
C60 0.00 CONCRETE SAWS (Add cost for sawblade wear) 95 A B 6,000 0.10 90 .900 .081 .043 0 .000 .000 .000 .477 .136 .161 0.00 0.00 0.00 1.00
C65 0.00 CONCRETE VIBRATORS 5 A B 4,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .161 0.00 0.00 0.00 2.50
C70 0.00 CRANES, GANTRY & STRADDLE 1
C75 0.00 CRANES, HYDRAULIC, SELF-PROPELLED 20 A B 14,000 0.15 75 .750 .068 .036 0 .000 .000 .000 .000 .136 .127 0.66 0.59 0.73 0.80
C80 0.00 CRANES, HYDRAULIC, TRUCK MOUNTED 1
C80 0.01 UNDER 26 TON 20 A B 14,000 0.15 65 .650 .059 .031 10 .100 .009 .005 .000 .161 .153 0.66 0.58 0.73 0.60
C80 0.01 UNDER 26 TON 20 S B 12,000 0.15 85 .850 .077 .041 13 .130 .012 .006 .000 .161 .153 0.18 0.14 0.20 0.65

D-3
EP 1110-1-8, Vol. 2
EP 1110-1-8
(Vol.30
1) Apr 14
4/30/2014
APPENDIX D
CATEGORY
C80 0.02 26 TON THRU 65 TON 20 A B 16,000 0.15 65 .650 .059 .031 10 .100 .009 .005 .000 .127 .110 0.66 0.58 0.73 0.70
C80 0.02 26 TON THRU 65 TON 20 S B 14,000 0.15 85 .850 .077 .041 13 .130 .012 .006 .000 .127 .110 0.18 0.14 0.20 0.75
C80 0.03 66 TON THRU 125 TON 20 A B 18,000 0.15 65 .650 .059 .031 10 .100 .009 .005 .000 .127 .110 0.66 0.58 0.73 0.80
C80 0.03 66 TON THRU 125 TON 20 S B 16,000 0.15 85 .850 .077 .041 13 .130 .012 .006 .000 .127 .110 0.18 0.14 0.20 0.85
C80 0.04 OVER 125 TON 20 A B 20,000 0.15 65 .650 .059 .031 10 .100 .009 .005 .000 .127 .110 0.66 0.58 0.73 0.90
C80 0.04 OVER 125 TON 20 S B 18,000 0.15 85 .850 .077 .041 13 .130 .012 .006 .000 .127 .110 0.18 0.14 0.20 0.95
C85 0.00 CRANES, MECHANICAL, LATTICE BOOM, CRAWLER 1
MOUNTED
C85 0.11 DRAGLINE, CLAMSHELL, 0 THRU 1.0 CY 20 A B 14,000 0.20 55 .550 .050 .026 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 0.80
C85 0.11 DRAGLINE, CLAMSHELL, 0 THRU 1.0 CY 20 S B 12,000 0.20 72 .720 .065 .034 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 0.90
C85 0.12 DRAGLINE, CLAMSHELL, OVER 1.0 CY THRU 2.5 20 A B 16,000 0.20 55 .550 .050 .026 0 .000 .000 .000 .000 .144 .144 0.00 0.00 0.00 0.85
CY
C85 0.12 DRAGLINE, CLAMSHELL, OVER 1.0 CY THRU 2.5 20 S B 13,000 0.20 72 .720 .065 .034 0 .000 .000 .000 .000 .144 .144 0.00 0.00 0.00 0.95
CY
C85 0.13 DRAGLINE, CLAMSHELL, OVER 2.5 CY THRU 5.0 20 A B 18,000 0.20 55 .550 .050 .026 0 .000 .000 .000 .000 .093 .093 0.00 0.00 0.00 0.95
CY
C85 0.13 DRAGLINE, CLAMSHELL, OVER 2.5 CY THRU 5.0 20 S B 15,000 0.20 72 .720 .065 .034 0 .000 .000 .000 .000 .093 .093 0.00 0.00 0.00 1.05
CY
C85 0.14 DRAGLINE, CLAMSHELL, OVER 5.0 CY 20 A B 20,000 0.20 55 .550 .050 .026 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.00 1.05
C85 0.14 DRAGLINE, CLAMSHELL, OVER 5.0 CY 20 S B 16,000 0.20 72 .720 .065 .034 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.00 1.15
C85 0.21 LIFTING, 0 THRU 25 TON 20 A B 16,000 0.20 40 .400 .036 .019 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 0.65
C85 0.21 LIFTING, 0 THRU 25 TON 20 S B 13,000 0.20 52 .520 .047 .025 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 0.70
C85 0.22 LIFTING, 26 TON THRU 50 TON 20 A B 18,000 0.20 40 .400 .036 .019 0 .000 .000 .000 .000 .085 .085 0.00 0.00 0.00 0.75
C85 0.22 LIFTING, 26 TON THRU 50 TON 20 S B 15,000 0.20 52 .520 .047 .025 0 .000 .000 .000 .000 .085 .085 0.00 0.00 0.00 0.80

D-4
EP 1110-1-8,
EPVol. 2
1110-1-8
30 Apr(Vol.
14 1)
4/30/2014
APPENDIX D
CATEGORY
C85 0.23 LIFTING, 51 TON THRU 150 TON 20 A B 20,000 0.15 40 .400 .036 .019 0 .000 .000 .000 .000 .093 .093 0.00 0.00 0.00 0.85
C85 0.23 LIFTING, 51 TON THRU 150 TON 20 S B 16,000 0.15 52 .520 .047 .025 0 .000 .000 .000 .000 .093 .093 0.00 0.00 0.00 0.90
C85 0.24 LIFTING, OVER 150 TON 20 A B 22,000 0.15 40 .400 .036 .019 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.00 0.95
C85 0.24 LIFTING, OVER 150 TON 20 S B 18,000 0.15 52 .520 .047 .025 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.00 1.00
C90 0.00 CRANES, MECHANICAL, LATTICE BOOM, TRUCK 1
MOUNTED
C90 0.01 UNDER 26 TON 20 A B 14,000 0.15 50 .500 .045 .024 10 .100 .009 .005 .000 .161 .153 0.66 0.58 0.73 0.60
C90 0.01 UNDER 26 TON 20 S B 12,000 0.15 65 .650 .059 .031 13 .130 .012 .006 .000 .161 .153 0.18 0.14 0.20 0.65
C90 0.02 26 TON THRU 65 TON 20 A B 16,000 0.15 50 .500 .045 .024 10 .100 .009 .005 .000 .127 .110 0.66 0.58 0.73 0.70
C90 0.02 26 TON THRU 65 TON 20 S B 14,000 0.15 65 .650 .059 .031 13 .130 .012 .006 .000 .127 .110 0.18 0.14 0.20 0.75
C90 0.03 66 TON THRU 125 TON 20 A B 18,000 0.20 50 .500 .045 .024 10 .100 .009 .005 .000 .127 .110 0.66 0.58 0.73 0.80
C90 0.03 66 TON THRU 125 TON 20 S B 16,000 0.20 65 .650 .059 .031 13 .130 .012 .006 .000 .127 .110 0.18 0.14 0.20 0.85
C90 0.04 OVER 125 TON 20 A B 20,000 0.20 50 .500 .045 .024 10 .100 .009 .005 .000 .127 .110 0.66 0.58 0.73 0.90
C90 0.04 OVER 125 TON 20 S B 18,000 0.20 65 .650 .059 .031 13 .130 .012 .006 .000 .127 .110 0.18 0.14 0.20 0.95
C95 0.00 CRANES, TOWER 20 A B 18,000 0.20 65 .650 .059 .031 10 .100 .009 .005 .530 .127 .110 0.00 0.00 0.92 0.85
D10 0.00 DRILLS, AIR/HYDRAULIC,CRWLR MTD,0" THRU 6.5" 1
DIA HOLE (Add cost for drill steel and bit wear)
D10 0.10 DRILLS, AIR TRACK (Add cost for drill steel and bit 25 A B 14,000 0.25 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 1.00
wear)
D10 0.20 DRILLS, HYDRAULIC TRACK (Add cost for drill steel 25 A B 10,000 0.25 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 1.00
and bit wear)
D15 0.00 DRILLS, HORIZONTAL 1
D15 0.10 DRILLS, HORIZONTAL BORING & GROUND 25 A B 10,000 0.25 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.90
PIERCING (Add cost for drill steel and bit wear)

D-5
EP 1110-1-8, Vol. 2
EP 1110-1-8
(Vol.30
1) Apr 14
4/30/2014
APPENDIX D
CATEGORY
D15 0.20 DRILLS, HORIZONTAL & DIRECTIONAL (Add cost for 25 A B 10,000 0.25 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.90
D20 0.00 DRILLS, CORE, COLUMN MOUNTED (Add cost for 25 A B 8,000 0.25 80 .800 .072 .038 0 .000 .000 .000 .477 .068 .102 0.00 0.00 0.00 0.85
D25 0.00 DRILLS, CORE & DOWELLING (Add cost for drill steel 25 A B 10,000 0.25 80 .800 .072 .038 0 .000 .000 .000 .477 .068 .102 0.00 0.00 0.92 1.00
and bit wear)
D30 0.00 DRILLS, EARTH / AUGER (Add cost for drill steel and 25 A B 10,000 0.25 80 .800 .072 .038 10 .100 .009 .005 .477 .136 .119 0.96 0.86 1.07 1.00
cutting edge wear)
D35 0.00 DRILLS, ROTARY BLASTHOLE (Add cost for drill steel 1
and bit wear)
D35 0.11 DIESEL, 4.5" THRU 9.875" DIAMETER HOLE (Add 25 A B 14,000 0.20 80 .800 .072 .038 10 .100 .009 .005 .005 .161 .161 0.96 0.86 1.07 1.00
cost for drill steel and bit wear)
D35 0.12 DIESEL, OVER 9.875" DIAMETER (Add cost for drill 25 A B 18,000 0.20 80 .800 .072 .038 10 .100 .009 .005 .011 .136 .136 0.96 0.86 1.07 1.00
steel and bit wear)
D35 0.21 ELECTRIC, 4.5" THRU 9.875" DIAMETER HOLE (Add 25 A B 14,000 0.20 70 .700 .063 .034 10 .100 .009 .005 .530 .000 .000 0.00 0.00 0.00 0.55
cost for drill steel and bit wear)
D35 0.22 ELECTRIC, OVER 9.875" DIAMETER (Add cost for 25 A B 18,000 0.20 70 .700 .063 .034 10 .100 .009 .005 .530 .000 .000 0.00 0.00 0.00 0.55
F10 0.00 FORK LIFTS 95 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .102 .102 0.83 0.46 0.92 0.75
G10 0.00 GENERATOR SETS 1
G10 0.10 PORTABLE 30 A B 8,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.73 0.60
G10 0.10 PORTABLE 30 S B 7,000 0.10 85 .850 .077 .041 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.20 0.70
G10 0.20 SKID MOUNTED 30 A B 10,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.00 0.70
G10 0.20 SKID MOUNTED 30 S B 8,000 0.10 85 .850 .077 .041 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.00 0.80
G15 0.00 GRADERS, MOTOR 35 A B 14,500 0.25 60 .600 .054 .029 0 .000 .000 .000 .000 .085 .144 0.83 0.54 0.92 0.75
G15 0.00 GRADERS, MOTOR 35 S B 13,500 0.25 78 .780 .070 .037 0 .000 .000 .000 .000 .085 .144 0.27 0.16 0.30 0.85

D-6
EP 1110-1-8,
EPVol. 2
1110-1-8
30 Apr(Vol.
14 1)
4/30/2014
APPENDIX D
CATEGORY
H10 0.00 HAMMERS, HYDRAULIC (Demolition tool) (Add cost 95 A B 6,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 1.00
for point wear)
H13 0.00 HAZARDOUS/TOXIC WASTE EQUIPMENT 1
H13 0.11 COMPACTORS (Compression force) 0 THRU 50 95 A B 10,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .530 .102 .102 1.08 0.86 1.20 0.80
TONS
H13 0.12 COMPACTORS (Compression force) OVER 50 TONS 95 A B 12,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .530 .102 .102 1.08 0.86 1.20 0.90
H13 0.21 FILTER PRESSES, STATIONARY 95 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .530 .102 .102 0.00 0.00 0.00 0.90
H13 0.22 FILTER PRESSES, MOBILE 95 A B 10,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .530 .102 .102 0.66 0.59 0.73 0.80
H13 0.30 CENTRIFUGES 95 A B 4,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .530 .000 .000 0.00 0.00 0.00 0.70
H13 0.40 SHREDDERS 95 A B 10,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 1.08 0.86 1.20 0.90
H13 0.51 SOIL TREATMENT PLANT, MOBILE 95 A B 10,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 0.77 0.69 0.86 1.00
H13 0.61 SLUDGE PROCESSING EQUIP, SLUDGE 95 A B 10,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 1.00
DISPENSERS
H13 0.71 WASTE HANDLING EQUIPMENT, DRUM HANDLING 95 A B 4,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 1.00
H15 0.00 HEATERS, SPACE 1
H20 0.00 HOISTS & AIR WINCHES 95 A B 9,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.00 0.80
H25 0.00 HYDRAULIC EXCAVATORS, CRAWLER MOUNTED 1
H25 0.10 0 LBS THRU 12,500 LBS (COMPACT EXCAVATORS) 65 A B 8,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .149 .149 0.00 0.00 0.00 0.70
H25 0.10 0 LBS THRU 12,500 LBS (COMPACT EXCAVATORS) 65 S B 7,000 0.25 85 .850 .077 .041 0 .000 .000 .000 .000 .149 .149 0.00 0.00 0.00 0.80
H25 0.11 OVER 12,500 LBS THRU 40,000 LBS 65 A B 8,500 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .149 .149 0.00 0.00 0.00 0.70
H25 0.11 OVER 12,500 LBS THRU 40,000 LBS 65 S B 7,000 0.25 85 .850 .077 .041 0 .000 .000 .000 .000 .149 .149 0.00 0.00 0.00 0.85

D-7
EP 1110-1-8, Vol. 2
EP 1110-1-8
(Vol.30
1) Apr 14
4/30/2014
APPENDIX D
CATEGORY
H25 0.14 OVER 160,000 LBS 65 A B 19,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .051 .051 0.00 0.00 0.00 1.10
H25 0.14 OVER 160,000 LBS 65 S B 15,000 0.25 85 .850 .077 .041 0 .000 .000 .000 .000 .051 .051 0.00 0.00 0.00 1.25
H25 0.21 ATTACHMENTS, MOBILE SHEARS 95 A B 6,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 0.90
H25 0.22 ATTACHMENTS, MATERIAL HANDLING 95 A B 6,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 0.80
H25 0.23 ATTACHMENTS, CONCRETE PULVERIZERS 95 A B 6,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 1.00
H25 0.24 ATTACHMENTS, COMPACTORS 95 A B 6,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 1.00
H30 0.00 HYDRAULIC EXCAVATORS, WHEEL MOUNTED 1
H30 0.01 0 THRU 1.0 CY 65 A B 8,000 0.25 60 .600 .054 .029 10 .100 .009 .005 .000 .149 .141 0.83 0.54 0.92 0.50
H30 0.01 0 THRU 1.0 CY 65 S B 6,500 0.25 78 .780 .070 .037 13 .130 .012 .006 .000 .149 .141 0.25 0.15 0.28 0.55
H30 0.02 OVER 1.0 CY 65 A B 10,000 0.25 60 .600 .054 .029 10 .100 .009 .005 .000 .149 .141 0.83 0.54 0.92 0.60
H30 0.02 OVER 1.0 CY 65 S B 8,000 0.25 78 .780 .070 .037 13 .130 .012 .006 .000 .149 .141 0.25 0.15 0.28 0.65
H35 0.00 HYDRAULIC SHOVELS, CRAWLER MOUNTED 1
H35 0.11 DIESEL, 0 CY THRU 5.0 CY 65 A B 14,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .047 .047 0.00 0.00 0.00 1.00
H35 0.11 DIESEL, 0 CY THRU 5.0 CY 65 S B 12,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .000 .047 .047 0.00 0.00 0.00 1.10
H35 0.12 DIESEL, OVER 5.0 CY 65 A B 16,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .051 .051 0.00 0.00 0.00 1.20
H35 0.12 DIESEL, OVER 5.0 CY 65 S B 14,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .000 .051 .051 0.00 0.00 0.00 1.30
H35 0.21 ELECTRIC, OVER 2.5 CY 65 A B 18,000 0.20 50 .500 .045 .024 0 .000 .000 .000 .265 .000 .000 0.00 0.00 0.00 0.80
H35 0.21 ELECTRIC, OVER 2.5 CY 65 S B 16,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .265 .000 .000 0.00 0.00 0.00 0.90
L10 0.00 LAND CLEARING EQUIPMENT 70 A B 10,000 0.20 60 .600 .054 .029 10 .100 .009 .005 .000 .127 .110 0.83 0.54 0.92 0.90
L10 0.00 LAND CLEARING EQUIPMENT 70 S B 7,000 0.20 78 .780 .070 .037 13 .130 .012 .006 .000 .127 .110 0.25 0.15 0.28 1.00

D-8
EP 1110-1-8,
EPVol. 2
1110-1-8
30 Apr(Vol.
14 1)
4/30/2014
APPENDIX D
CATEGORY
L15 0.00 LANDSCAPING EQUIPMENT 95 A B 4,000 0.15 80 .800 .072 .038 13 .130 .012 .006 .477 .102 .102 0.59 0.30 0.66 0.70
L20 0.00 LIGHTING SETS, TRAILER MOUNTED 1
L20 0.10 METALLIC VAPOR 95 A B 8,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .000 .102 .102 0.66 0.58 0.73 1.50
L25 0.00 LINE STRIPING EQUIPMENT 95 A B 8,000 0.20 85 .850 .077 .041 13 .130 .012 .006 .000 .102 .102 0.66 0.58 0.73 1.20
L30 0.00 LOADERS, BELT (Conveyor belts) & ACCESSORIES 95 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .119 .119 0.66 0.58 0.73 1.00
L30 0.00 LOADERS, BELT (Conveyor belts) & ACCESSORIES 95 S B 8,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .477 .119 .119 0.21 0.16 0.23 1.10
L35 0.00 LOADERS, FRONT END, CRAWLER TYPE 40 A B 10,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .000 .170 .101 0.00 0.00 0.00 1.10
L35 0.00 LOADERS, FRONT END, CRAWLER TYPE 40 S B 8,000 0.20 91 .910 .082 .044 0 .000 .000 .000 .000 .170 .101 0.00 0.00 0.00 1.25
L40 0.00 LOADERS, FRONT END, WHEEL TYPE 1
L40 0.11 ARTICULATED, 0 THRU 225 HP 45 A B 9,250 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .170 .111 0.83 0.54 0.92 0.70
L40 0.11 ARTICULATED, 0 THRU 225 HP 45 S B 8,750 0.25 85 .850 .077 .041 0 .000 .000 .000 .000 .170 .111 0.25 0.15 0.28 0.80
L40 0.12 ARTICULATED, OVER 225 HP 45 A B 13,500 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .170 .080 0.83 0.54 0.92 0.70
L40 0.12 ARTICULATED, OVER 225 HP 45 S B 12,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .000 .170 .080 0.25 0.15 0.28 0.75
L40 0.20 SKID STEER 45 A B 8,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .000 .170 .111 0.57 0.29 0.63 0.80
L40 0.21 SKID STEER ATTACHMENTS 45 A B 4,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .170 .170 0.00 0.00 0.00 1.00
L40 0.31 TOOL CARRIER & TELESCOPIC HANDLERS, 0 45 A B 10,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .170 .111 0.83 0.54 0.92 0.85
THRU 225 HP
L40 0.31 TOOL CARRIER & TELESCOPIC HANDLERS, 0 45 S B 9,250 0.25 85 .850 .077 .041 0 .000 .000 .000 .000 .170 .111 0.25 0.15 0.28 0.90
THRU 225 HP
L40 0.32 TOOL CARRIER & TELESCOPIC HANDLERS, OVER 45 A B 12,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .170 .080 0.83 0.54 0.92 0.85
225 HP
L40 0.32 TOOL CARRIER & TELESCOPIC HANDLERS, OVER 45 S B 10,000 0.15 85 .850 .077 .041 0 .000 .000 .000 .000 .170 .080 0.25 0.15 0.28 0.90
225 HP
L45 0.00 LOADERS / BACKHOE, CRAWLER TYPE 40 A B 8,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .000 .441 .524 0.00 0.00 0.00 1.35

D-9
EP 1110-1-8, Vol. 2
EP 1110-1-8
(Vol.30
1) Apr 14
4/30/2014
APPENDIX D
CATEGORY
L45 0.00 LOADERS / BACKHOE, CRAWLER TYPE 40 S B 6,000 0.20 91 .910 .082 .044 0 .000 .000 .000 .000 .441 .524 0.00 0.00 0.00 1.40
L50 0.00 LOADERS / BACKHOE, WHEEL TYPE 45 A B 10,000 0.25 50 .500 .045 .024 0 .000 .000 .000 .000 .441 .441 0.83 0.54 0.92 0.80
L50 0.00 LOADERS / BACKHOE, WHEEL TYPE 45 S B 6,000 0.25 70 .700 .063 .034 0 .000 .000 .000 .000 .441 .441 0.25 0.15 0.28 0.85
L55 0.00 LOADER / BACKHOE, ATTACHMENTS 95 A B 6,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .441 .441 0.00 0.00 0.00 1.00
L60 0.00 LOG SKIDDERS 75 A B 10,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .119 0.83 0.54 0.92 0.70
L60 0.00 LOG SKIDDERS 75 S B 8,000 0.15 85 .850 .077 .041 0 .000 .000 .000 .000 .102 .119 0.25 0.15 0.28 0.80
M10 0.00 MARINE EQUIPMENT (NON DREDGING) 1
M10 0.11 AQUATIC MAINTENANCE 105 A B 10,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.70
M10 0.12 AQUATIC MAINTENANCE ATTACHMENTS 105 A B 6,000 0.20 80 .800 .072 .038 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.60
M10 0.21 HYDRAULIC CUTTERHEAD DREDGE, 8" OR 105 A B 16,000 0.10 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.70
LESS,TRANSPORTABLE
M10 0.22 HYDRAULIC CUTTERHEAD DREDGE,8" - 105 A B 16,000 0.10 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.80
12",TRANSPORTABLE
M10 0.23 HYDRAULIC AUGERHEAD DREDGE,12" OR 105 A B 16,000 0.10 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.80
LESS,TRANSPORTABLE
M10 0.24 HYDRAULIC FLOATING PUMPS,12" OR 105 A B 8,000 0.10 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.70
LESS,TRANSPORTABLE
M10 0.25 HYDRAULIC DREDGE PUMPS,12" OR 105 A B 6,000 0.15 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.70
LESS,TRANSPORTABLE
M10 0.26 HYDRAULIC DREDGE / PUMP ATTACHMENTS 105 A B 6,000 0.15 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.60
M10 0.31 SMALL MECH DREDGES,CLAMSHELL,BARGE-MTD 20 A B 18,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .477 .102 .102 0.00 0.00 0.00 1.00
TO 5 CY
M10 0.31 SMALL MECH DREDGES,CLAMSHELL,BARGE-MTD 20 S B 16,000 0.15 85 .850 .077 .041 0 .000 .000 .000 .477 .102 .102 0.00 0.00 0.00 1.05
TO 5 CY

D-10
EP 1110-1-8,
EPVol. 2
1110-1-8
30 Apr(Vol.
14 1)
4/30/2014
APPENDIX D
CATEGORY
M10 0.32 SMALL MECH DREDGES, AMPHIBIOUS 65 A B 10,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .477 .161 .161 0.00 0.00 0.00 1.00
EXCAVATORS
M10 0.32 SMALL MECH DREDGES, AMPHIBIOUS 65 S B 9,000 0.15 85 .850 .077 .041 0 .000 .000 .000 .477 .161 .161 0.00 0.00 0.00 1.10
EXCAVATORS
M10 0.33 SMALL MECH DREDGES,HOE-MOUNTED 105 A B 20,000 0.15 80 .800 .072 .038 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.90
DREDGING ATTACH
M10 0.41 WORK FLOATS (NON-DREDGING) 105 A B 6,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.50
M10 0.42 WORK BARGES (SECTIONAL, NON-DREDGING) 105 A B 30,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.60
M10 0.45 FLAT-DECK OR CARGO BARGE (NON-DREDGING) 105 A B 90,000 0.05 20 .200 .018 .010 0 .000 .000 .000 .000 .000 .136 0.00 0.00 0.00 0.60
M10 0.46 DUMP SCOW (NON-DREDGING) 105 A B 90,000 0.05 20 .200 .018 .010 0 .000 .000 .000 .000 .000 .136 0.00 0.00 0.00 0.70
M10 0.47 DRILL BARGE (NON-DREDGING) 105 A B 30,000 0.05 20 .200 .018 .010 0 .000 .000 .000 .000 .000 .136 0.00 0.00 0.00 0.70
M10 0.48 ALL OTHER BARGES (NON-DREDGING) 105 A B 30,000 0.05 20 .200 .018 .010 0 .000 .000 .000 .000 .000 .136 0.00 0.00 0.00 0.70
M10 0.51 BOATS & LAUNCHES, 0 THRU 250 HP 105 A B 16,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .161 0.00 0.00 0.00 0.70
M10 0.51 BOATS & LAUNCHES, 0 THRU 250 HP 105 S B 13,000 0.15 85 .850 .077 .041 0 .000 .000 .000 .477 .136 .161 0.00 0.00 0.00 0.75
M10 0.53 BOATS & LAUNCHES, 251 THRU 500 HP 105 A B 18,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .161 0.00 0.00 0.00 0.80
M10 0.53 BOATS & LAUNCHES, 251 THRU 500 HP 105 S B 15,000 0.10 85 .850 .077 .041 0 .000 .000 .000 .477 .136 .161 0.00 0.00 0.00 0.85
M10 0.54 TUGS, 501 THRU 1,000 HP 105 A B 40,000 0.10 60 .600 .054 .029 50 .500 .045 .024 .477 .136 .161 0.00 0.00 0.00 0.90
M10 0.55 TUGS, 1,000 THRU 2,000 HP 105 A B 55,000 0.10 60 .600 .054 .029 50 .500 .045 .024 .477 .136 .161 0.00 0.00 0.00 1.00
P10 0.00 PILE HAMMER ACCESSORIES - EXTRACTORS & 50 A B 6,000 0.35 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .136 0.00 0.00 0.00 0.80
BOX LEADS
P20 0.00 PILE HAMMERS, DOUBLE ACTING 1
P20 0.10 DIESEL 50 A B 6,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 1.10
P20 0.20 PNEUMATIC (STEAM/AIR) 50 A B 6,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 1.10
P25 0.00 PILE HAMMERS, SINGLE ACTING 1

D-11
EP 1110-1-8, Vol. 2
EP 1110-1-8
(Vol.30
1) Apr 14
4/30/2014
APPENDIX D
CATEGORY
P25 0.10 DIESEL 50 A B 6,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 1.00
P25 0.20 PNEUMATIC (STEAM/AIR) 50 A B 6,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 1.00
P30 0.00 PILE HAMMERS, DRIVER/ EXTRACTOR, VIBRATORY 50 A B 6,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .136 0.00 0.00 0.00 1.00
P35 0.00 PIPELAYERS 70 A B 14,000 0.20 35 .350 .032 .017 0 .000 .000 .000 .000 .000 .170 0.00 0.00 0.00 0.95
P35 0.00 PIPELAYERS 70 S B 11,500 0.20 46 .460 .041 .022 0 .000 .000 .000 .000 .000 .170 0.00 0.00 0.00 1.10
P40 0.00 PLATFORMS & MAN-LIFTS 20 A B 8,000 0.10 50 .500 .045 .024 50 .500 .045 .024 .477 .136 .119 0.66 0.33 0.73 0.80
P45 0.00 PUMPS, GROUT 95 A B 8,000 0.15 95 .950 .086 .045 0 .000 .000 .000 .477 .136 .119 0.66 0.59 0.73 1.00
P50 0.00 PUMPS, WATER, CENTRIFUGAL, TRASH 1
P50 0.11 ENGINE DRIVE 95 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .161 0.66 0.00 0.73 0.90
P50 0.12 ELECTRIC DRIVE 95 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .477 .000 .000 0.66 0.00 0.73 0.50
P50 0.21 WHEEL MOUNTED, ENGINE DRIVE 95 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .161 0.66 0.00 0.73 0.90
P50 0.22 WHEEL MOUNTED, ELECTRIC DRIVE 95 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .477 .000 .000 0.66 0.00 0.73 0.50
P50 0.31 HOSES, PUMP, SUCTION & DISCHARGE 95 A B 4,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 1.50
P55 0.00 PUMPS, WATER, SUBMERSIBLE 1
P55 0.01 ENGINE DRIVE 95 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .161 0.00 0.00 0.00 1.00
P60 0.00 PUMPS, WATER, CENTRIFUGAL, DEWATERING 1
P60 0.11 SKID MOUNTED, ENGINE DRIVE 95 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .161 0.00 0.00 0.00 0.90
P60 0.12 SKID MOUNTED, ELECTRIC DRIVE 95 A B 8,000 0.15 90 .900 .081 .043 0 .000 .000 .000 .477 .000 .000 0.00 0.00 0.00 0.50
P65 0.00 PUMPS, WATER, DIAPHRAGM 1

D-12
EP 1110-1-8,
EPVol. 2
1110-1-8
30 Apr(Vol.
14 1)
4/30/2014
APPENDIX D
CATEGORY
P65 0.11 SKID MOUNTED, ENGINE DRIVE 95 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .161 0.00 0.00 0.00 0.90
P65 0.12 SKID MOUNTED, ELECTRIC DRIVE 95 A B 8,000 0.15 90 .900 .081 .043 0 .000 .000 .000 .477 .000 .000 0.00 0.00 0.00 0.50
P70 0.00 PUMPS, WATER (For core drills) 1
P70 0.01 ENGINE DRIVE 95 A B 8,000 0.25 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .161 0.00 0.00 0.00 0.80
R10 0.00 RIPPERS & HYDRAULIC BANK SLOPERS (Add cost 70 A B 8,000 0.20 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.90
for point wear)
R10 0.00 RIPPERS & HYDRAULIC BANK SLOPERS (Add cost 70 S B 6,500 0.20 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 1.00
for point wear)
R15 0.00 ROLLERS, STATIC, TOWED, PNEUMATIC 55 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.92 0.70
R20 0.00 ROLLERS, STATIC, TOWED, STEEL DRUM 55 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.92 0.80
R30 0.00 ROLLERS, STATIC, SELF-PROPELLED 1
R30 0.01 PNEUMATIC 55 A B 8,000 0.15 80 .800 .072 .038 0 .000 .000 .000 .000 .102 .102 0.83 0.54 0.92 0.70
R30 0.02 SMOOTH DRUM 55 A B 10,000 0.15 80 .800 .072 .038 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.00 0.80
R30 0.03 TAMPING FOOT, LANDFILL & SOIL COMPACTORS 55 A B 12,000 0.20 80 .800 .072 .038 0 .000 .000 .000 .000 .102 .102 0.00 0.00 0.00 0.80
R40 0.00 ROLLERS, VIBRATORY, TOWED 55 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 0.80
R45 0.00 ROLLERS, VIBRATORY, SELF-PROPELLED, 55 A B 8,000 0.20 90 .900 .081 .043 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 1.10
DOUBLE DRUM
R50 0.00 ROLLERS, VIBRATORY, SELF-PROPELLED, SINGLE 55 A B 8,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.83 0.54 0.92 1.00
DRUM
R55 0.00 ROOFING EQUIPMENT 95 A B 6,000 0.15 60 .600 .054 .029 0 .000 .000 .000 .477 .102 .102 0.97 0.87 1.08 0.80
S10 0.00 SCRAPERS, ELEVATING 1

D-13
EP 1110-1-8, Vol. 2
EP 1110-1-8
(Vol.30
1) Apr 14
4/30/2014
APPENDIX D
CATEGORY
S10 0.01 0 THRU 200 HP 60 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .000 .170 0.84 0.55 0.93 0.90
S10 0.01 0 THRU 200 HP 60 S B 8,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .000 .000 .170 0.23 0.13 0.25 1.00
S10 0.02 OVER 200 HP 60 A B 13,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .000 .136 0.84 0.55 0.93 0.95
S10 0.02 OVER 200 HP 60 S B 11,500 0.25 85 .850 .077 .041 0 .000 .000 .000 .000 .000 .136 0.23 0.13 0.25 1.00
S15 0.00 SCRAPERS, CONVENTIONAL 60 A B 15,000 0.20 60 .600 .054 .029 0 .000 .000 .000 .000 .000 .136 0.84 0.55 0.93 0.80
S15 0.00 SCRAPERS, CONVENTIONAL 60 S B 12,500 0.20 78 .780 .070 .037 0 .000 .000 .000 .000 .000 .136 0.23 0.13 0.25 0.85
S20 0.00 SCRAPERS, TANDEM POWERED 60 A B 15,000 0.20 62 .620 .056 .030 62 .620 .056 .030 .000 .000 .110 0.84 0.55 0.93 0.85
S20 0.00 SCRAPERS, TANDEM POWERED 60 S B 13,500 0.20 81 .810 .073 .039 81 .810 .073 .039 .000 .000 .110 0.23 0.13 0.25 0.90
S25 0.00 SCRAPERS, TRACTOR DRAWN 60 A B 12,000 0.20 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.84 0.55 0.93 0.70
S25 0.00 SCRAPERS, TRACTOR DRAWN 60 S B 10,000 0.20 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.23 0.13 0.25 0.75
S30 0.00 SCREENING & CRUSHING PLANTS 1
S30 0.10 CONVEYORS 95 A B 10,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 1.08 0.86 1.20 0.70
S30 0.10 CONVEYORS 95 S B 8,000 0.10 78 .780 .070 .037 0 .000 .000 .000 .577 .163 .142 0.96 0.72 1.07 0.85
S30 0.20 CRUSHERS - VERTICAL & HORIZONTAL SHAFT 95 A B 25,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 1.08 0.86 1.20 1.00
IMPACTOR
S30 0.20 CRUSHERS - VERTICAL & HORIZONTAL SHAFT 95 S B 15,000 0.10 78 .780 .070 .037 0 .000 .000 .000 .577 .163 .142 0.96 0.72 1.07 1.25
IMPACTOR
S30 0.21 CRUSHERS - CONE 95 A B 25,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 1.08 0.86 1.20 1.20
S30 0.21 CRUSHERS - CONE 95 S B 15,000 0.10 78 .780 .070 .037 0 .000 .000 .000 .577 .163 .142 0.96 0.72 1.07 1.60
S30 0.22 CRUSHERS - JAW 95 A B 25,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 1.08 0.86 1.20 0.65
S30 0.22 CRUSHERS - JAW 95 S B 15,000 0.10 78 .780 .070 .037 0 .000 .000 .000 .577 .163 .142 0.96 0.72 1.07 0.85
S30 0.30 SCREENING PLANT 95 A B 10,000 0.10 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 1.08 0.86 1.20 0.80
S30 0.30 SCREENING PLANT 95 S B 8,000 0.10 78 .780 .070 .037 0 .000 .000 .000 .577 .163 .142 0.96 0.72 1.07 1.00

D-14
EP 1110-1-8,
EPVol. 2
1110-1-8
30 Apr(Vol.
14 1)
4/30/2014
APPENDIX D
CATEGORY
S35 0.00 SNOW REMOVAL EQUIPMENT 95 A B 8,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .000 .119 0.00 0.00 0.00 0.80
S40 0.00 SOIL & ROAD STABILIZERS 60 A B 10,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .000 .000 .119 0.84 0.55 0.96 0.85
S40 0.00 SOIL & ROAD STABILIZERS 60 S B 8,000 0.20 91 .910 .082 .044 0 .000 .000 .000 .000 .000 .119 0.23 0.13 0.25 0.95
S45 0.00 SPLITTERS, ROCK & CONCRETE 95 A B 6,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .136 0.00 0.00 0.00 1.00
T10 0.00 TRACTOR BLADES & ATTACHMENTS (including 70 A B 10,000 0.20 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.96 0.80
agricultural)
T10 0.00 TRACTOR BLADES & ATTACHMENTS (including 70 S B 8,000 0.20 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.86 0.90
agricultural)
T15 0.00 TRACTORS, CRAWLER (DOZER) (includes blade) 1
T15 0.01 0 THRU 225 HP 70 A B 10,000 0.30 70 .700 .063 .034 0 .000 .000 .000 .000 .000 .153 0.00 0.00 0.00 1.10
T15 0.01 0 THRU 225 HP 70 S B 8,000 0.30 91 .910 .082 .044 0 .000 .000 .000 .000 .000 .153 0.00 0.00 0.00 1.25
T15 0.02 226 HP THRU 425 HP 70 A B 12,500 0.25 70 .700 .063 .034 0 .000 .000 .000 .000 .000 .119 0.00 0.00 0.00 1.20
T15 0.02 226 HP THRU 425 HP 70 S B 10,500 0.25 91 .910 .082 .044 0 .000 .000 .000 .000 .000 .119 0.00 0.00 0.00 1.25
T15 0.03 OVER 425 HP 70 A B 15,000 0.20 60 .600 .054 .029 0 .000 .000 .000 .000 .000 .066 0.00 0.00 0.00 1.20
T15 0.03 OVER 425 HP 70 S B 12,500 0.20 78 .780 .070 .037 0 .000 .000 .000 .000 .000 .066 0.00 0.00 0.00 1.35
T20 0.00 TRACTORS, WHEEL TYPE (DOZER) 75 A B 14,000 0.15 60 .600 .054 .029 0 .000 .000 .000 .000 .102 .119 0.96 0.63 0.00 0.60
T20 0.00 TRACTORS, WHEEL TYPE (DOZER) 75 S B 13,000 0.15 78 .780 .070 .037 0 .000 .000 .000 .000 .102 .119 0.25 0.15 0.00 0.65
T25 0.00 TRACTORS, AGRICULTURAL 1
T25 0.10 CRAWLER 75 A B 10,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .119 0.00 0.00 0.00 0.85
T25 0.20 WHEEL 75 A B 8,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .119 0.96 0.73 0.00 0.70
T30 0.00 TRENCHERS, CHAIN TYPE CUTTER 80 A B 8,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .119 .119 1.08 0.82 0.00 0.90
T30 0.00 TRENCHERS, CHAIN TYPE CUTTER 80 S B 6,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .000 .119 .119 0.32 0.22 0.00 1.00
T35 0.00 TRENCHERS, WHEEL TYPE CUTTER 80 A B 8,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .119 .119 1.08 0.82 0.00 0.90

D-15
EP 1110-1-8, Vol. 2
EP 1110-1-8
(Vol.30
1) Apr 14
4/30/2014
APPENDIX D
CATEGORY
T35 0.00 TRENCHERS, WHEEL TYPE CUTTER 80 S B 6,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .000 .119 .119 0.32 0.22 0.00 1.00
T40 0.00 TRUCK OPTIONS 1
T40 0.10 CRANES / HOISTS, PERSONNEL & MATERIAL 95 A B 8,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .136 0.00 0.00 0.00 0.80
HANDLING
T40 0.20 DUMP BODY, REAR 95 A B 8,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.70
T40 0.20 DUMP BODY, REAR 95 S B 6,500 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.80
T40 0.30 FLATBEDS, WITH SIDES 95 A B 8,000 0.20 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.00 0.60
T40 0.41 HOIST, ELECTRIC DRIVE 95 A B 8,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .136 0.00 0.00 0.00 0.70
T40 0.50 TRANSIT MIXERS 95 A B 8,000 0.15 65 .650 .059 .031 35 .350 .032 .017 .477 .136 .136 0.77 0.69 0.86 0.70
T40 0.60 WATER TANKS 95 A B 8,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .136 0.00 0.00 0.00 0.60
T40 0.70 ALL OTHER OPTIONS 95 A B 8,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .136 1.08 0.86 1.20 0.70
T45 0.00 TRUCK TRAILERS 1
T45 0.10 BOTTOM DUMP 95 A B 10,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.66 0.00 0.73 0.70
T45 0.10 BOTTOM DUMP 95 S B 8,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.18 0.00 0.20 0.80
T45 0.20 END DUMP 95 A B 10,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.66 0.00 0.73 0.65
T45 0.20 END DUMP 95 S B 8,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.18 0.00 0.20 0.75
T45 0.30 PUP TRAILER 95 A B 8,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.66 0.00 0.73 0.60
T45 0.41 LOWBOY, RIGID NECK, DROP DECK 95 A B 10,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.66 0.00 0.73 0.50
T45 0.50 FLATBED TRAILER 95 A B 10,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.66 0.00 0.73 0.50
T45 0.60 MISCELLANEOUS / UTILITY 95 A B 10,000 0.10 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.66 0.00 0.73 0.50
T45 0.70 WATER TANKER TRAILER 95 A B 10,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .119 .102 0.66 0.92 0.73 0.60
T45 0.80 DECONTAMINATION FACILITY 95 A B 8,000 0.25 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.66 0.00 0.73 0.70
T45 0.90 TANK TRAILERS 95 A B 10,000 0.25 65 .650 .059 .031 0 .000 .000 .000 .000 .119 .102 0.66 0.00 0.73 0.70

D-16
EP 1110-1-8,
EPVol. 2
1110-1-8
30 Apr(Vol.
14 1)
4/30/2014
APPENDIX D
CATEGORY
T50 0.00 TRUCKS, HIGHWAY (Add attachments as required) 1

T50 0.01 0 THRU 10,000 GVW 85 A S 8,000 0.20 15 .150 .014 .007 0 .000 .000 .000 .000 .119 .102 0.61 0.56 0.67 0.70
T50 0.01 0 THRU 10,000 GVW 85 S S 6,500 0.20 20 .200 .018 .010 0 .000 .000 .000 .000 .119 .102 0.20 0.16 0.22 0.75
T50 0.02 OVER 10,000 THRU 30,000 GVW (Chassis only - Add 85 A S 10,000 0.20 35 .350 .032 .017 0 .000 .000 .000 .000 .127 .110 0.72 0.66 0.79 0.65
options)
T50 0.02 OVER 10,000 THRU 30,000 GVW (Chassis only - Add 85 S S 8,000 0.20 46 .460 .041 .022 0 .000 .000 .000 .000 .127 .110 0.20 0.16 0.22 0.70
options)
T50 0.03 OVER 30,000 GVW (Chassis only - Add options) 85 A S 12,000 0.20 50 .500 .045 .024 0 .000 .000 .000 .000 .136 .119 0.77 0.71 0.86 0.65
T50 0.03 OVER 30,000 GVW (Chassis only - Add options) 85 S S 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .136 .119 0.21 0.18 0.24 0.75
T55 0.00 TRUCKS, OFF-HIGHWAY 1
T55 0.10 RIGID FRAME 90 A B 20,000 0.15 35 .350 .032 .017 0 .000 .000 .000 .000 .000 .144 0.84 0.73 0.93 0.90
T55 0.10 RIGID FRAME 90 S B 18,000 0.15 45 .450 .041 .022 0 .000 .000 .000 .000 .000 .144 0.23 0.18 0.25 0.95
T55 0.20 ARTICULATED FRAME 90 A B 13,000 0.15 50 .500 .045 .024 0 .000 .000 .000 .000 .000 .080 0.84 0.73 0.93 0.80
T55 0.20 ARTICULATED FRAME 90 S B 12,250 0.15 60 .600 .054 .029 0 .000 .000 .000 .000 .000 .080 0.23 0.18 0.25 0.85
T56 0.00 TRUCKS,OFF-HIGHWAY/PRIME MOVER TRACTORS 1
& WAGONS
T56 0.10 PRIME MOVER TRACTORS 90 A B 20,000 0.15 40 .400 .036 .019 0 .000 .000 .000 .000 .102 .144 0.84 0.64 0.93 0.90
T56 0.10 PRIME MOVER TRACTORS 90 S B 18,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .136 0.23 0.16 0.25 0.95
T56 0.20 WAGONS, BOTTOM DUMP 90 A B 15,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .136 0.84 0.64 0.93 0.65
T56 0.20 WAGONS, BOTTOM DUMP 90 S B 10,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .000 .102 .136 0.23 0.16 0.25 0.75
T56 0.30 WAGONS, REAR DUMP 90 A B 12,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .136 0.84 0.65 0.93 0.60
T57 0.00 TRUCKS, VACUUM 95 A B 10,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .119 0.23 0.17 0.25 0.80
T60 0.00 TRUCKS, WATER, OFF-HIGHWAY 90 A B 12,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .136 0.90 0.69 1.00 0.70

D-17
EP 1110-1-8, Vol. 2
EP 1110-1-8
(Vol.30
1) Apr 14
4/30/2014
APPENDIX D
CATEGORY
T60 0.00 TRUCKS, WATER, OFF-HIGHWAY 90 S B 10,000 0.20 85 .850 .077 .041 0 .000 .000 .000 .000 .102 .136 0.25 0.17 0.28 0.80
T65 0.00 TUNNEL/MINING EQUIPMENT 1
T65 0.10 DRIFTING & TUNNELING DRILLS 25 A B 14,000 0.15 80 .800 .072 .038 13 .130 .012 .006 .530 .136 .119 0.67 0.57 0.00 0.90
T65 0.20 TUNNEL BORING MACHINES 95 A B 18,000 0.15 70 .700 .063 .034 0 .000 .000 .000 .530 .000 .000 0.00 0.00 0.00 0.70
T65 0.20 TUNNEL BORING MACHINES 95 S B 16,000 0.15 91 .910 .082 .044 0 .000 .000 .000 .530 .000 .000 0.00 0.00 0.00 0.80
T65 0.30 PRODUCTION DRILLING RIGS 25 A B 12,000 0.15 80 .800 .072 .038 0 .000 .000 .000 .530 .136 .119 0.00 0.00 0.00 0.90
T65 0.40 ROADHEADERS & CONTINUOUS MINERS 95 A B 16,000 0.15 70 .700 .063 .034 0 .000 .000 .000 .530 .000 .000 0.00 0.00 0.00 0.90
T65 0.40 ROADHEADERS & CONTINUOUS MINERS 95 S B 14,000 0.15 91 .910 .082 .044 0 .000 .000 .000 .530 .000 .000 0.00 0.00 0.00 1.00
T65 0.50 ROCK BOLTING EQUIPMENT 95 A B 10,000 0.20 80 .800 .072 .038 10 .100 .009 .005 .530 .136 .119 0.00 0.00 0.00 0.80
T65 0.61 LOADING & HAULING EQUIPMENT, DIESEL OR 95 A B 12,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .000 .136 .127 0.00 0.00 0.00 0.75
GAS
T65 0.62 LOADING & HAULING EQUIPMENT, ELECTRIC 95 A B 14,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .477 .102 .102 0.00 0.00 0.00 0.70
T65 0.63 LOADING & HAULING EQUIPMENT, AIR-POWERED 95 A B 10,000 0.25 70 .700 .063 .034 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.65
T65 0.70 LOCOMOTIVES 95 A B 12,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .477 .136 .119 0.00 0.00 0.00 0.75
T65 0.90 OTHER TUNNELING EQUIPMENT 95 A B 10,000 0.20 70 .700 .063 .034 13 .130 .012 .006 .477 .136 .127 0.00 0.00 0.00 0.80
W10 0.00 WAGONS, BOTTOM DUMP 90 A B 12,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .136 0.88 0.67 0.98 0.65
W10 0.00 WAGONS, BOTTOM DUMP 90 S B 10,000 0.15 85 .850 .077 .041 0 .000 .000 .000 .000 .102 .136 0.25 0.17 0.28 0.75
W15 0.00 WAGONS, REAR DUMP 90 A B 12,000 0.15 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .136 0.88 0.77 0.98 0.60
W15 0.00 WAGONS, REAR DUMP 90 S B 10,000 0.15 85 .850 .077 .041 0 .000 .000 .000 .000 .102 .136 0.25 0.19 0.28 0.70
W25 0.00 WATER & CO2 BLASTERS 1
W25 0.10 LOW PRESSURE, (< 5,000 PSI) 95 A B 4,000 0.20 95 .950 .086 .045 0 .000 .000 .000 .424 .102 .119 0.96 0.73 1.07 1.10
W25 0.20 HIGH PRESSURE, (>= 5,000 PSI) 95 A B 4,000 0.20 95 .950 .086 .045 0 .000 .000 .000 .424 .102 .119 0.96 0.73 1.07 1.20
W25 0.30 STEAM CLEANERS 95 A B 4,000 0.20 95 .950 .086 .045 0 .000 .000 .000 .424 .102 .119 0.00 0.00 0.73 1.10

D-18
EP 1110-1-8,
EPVol. 2
1110-1-8
30 Apr(Vol.
14 1)
4/30/2014
APPENDIX D
CATEGORY
W25 0.40 CO2 BLASTERS 95 A B 6,000 0.20 70 .700 .063 .034 0 .000 .000 .000 .530 .127 .148 0.00 0.00 0.73 1.00
W25 0.50 WET ABRASIVE BLASTING SYSTEM (TORBO) 95 A B 10,000 0.35 0 .000 .000 .000 0 .000 .000 .000 .000 .000 .000 0.00 0.00 0.73 0.40
W30 0.00 WATER TANKS 1
W30 0.10 PORTABLE WITH WHEELS 90 A B 12,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .119 0.00 0.00 0.73 0.60
W30 0.20 SKID MOUNTED 90 A B 12,000 0.20 65 .650 .059 .031 0 .000 .000 .000 .000 .102 .119 0.00 0.00 0.00 0.50
W35 0.00 WELDERS 1
W35 0.10 ENGINE DRIVEN 95 A B 8,000 0.25 80 .800 .072 .038 0 .000 .000 .000 .000 .102 .102 0.00 0.00 1.07 0.75
W35 0.20 ELECTRIC DRIVEN 95 A B 6,000 0.20 30 .300 .027 .014 0 .000 .000 .000 .424 .000 .000 0.00 0.00 0.00 0.50

D-19
EP 1110-1-8, Vol. 2
30 Apr 14
D-20
EP 1110-1-8
(Vol. 8)
4/30/2014
EP 1110-1-8, Vol. 2
APPENDIX E 30 Apr 14
ECONOMIC INDEXES FOR CONSTRUCTION EQUIPMENT
Note: Table 2-1 Equipment Rates are based on equipment purchased new in the year 2011
KEY {--Projected---------}
(EK) 2016 2015 2014 2013 2012 2011 2010 2009 2008 2007 2006 2005 2004 2003 2002 2001 2000 1999 1998
EQUIPMENT DIVISIONS
5 Air Equipment 3165 3105 3047 3007 2887 2796 2601 2585 2458 2319 2234 2157 2085 2075 2069 2079 2047 2078 2074
10 Asphalt & Concrete Paving Equipment 5142 5046 4951 4855 4767 4652 4534 4526 4381 4228 4116 3950 3758 3763 3769 3766 3717 3638 3589
15 Buckets 9944 9757 9574 9448 9257 9135 8862 8911 8687 8604 8502 8057 7626 7443 7254 6804 6900 6982 6930
20 Cranes, Draglines & Clamshells - Crawler & Truck Mtd 7653 7509 7368 7271 7124 7031 6820 6858 6685 6621 6543 6201 5869 5728 5582 5236 5310 5289 5225
25 Drills 6824 6695 6569 6469 6391 6205 5987 5938 5783 5448 5104 4762 4444 4192 4116 3819 3736 3683 3626
30 Generators 6807 6679 6553 6458 6397 6262 5905 5794 5628 5357 5112 4888 4641 4566 4548 4548 4529 4520 4517
35 Graders, Motor 9365 9189 9016 8914 8648 7920 7632 7516 7155 6909 6825 6578 6318 6117 6049 5979 5952 5853 5682
40 Loaders, Track 8813 8647 8485 8378 8088 7713 7434 7454 7254 7037 6907 6653 6347 6177 6081 6058 6032 5960 5792
45 Loaders, Wheel 8133 7980 7830 7732 7464 7119 6861 6880 6695 6494 6374 6140 5857 5701 5612 5591 5567 5511 5409
50 Pile Driving Equipment 7628 7485 7344 7247 7063 6787 6582 6569 6375 6176 6033 5787 5450 5270 5195 5127 5112 5062 4993
55 Rollers 7890 7741 7596 7488 7341 7157 6983 6938 6736 6424 6145 5872 5646 5406 5285 5225 5130 5204 5092
60 Scrapers & Soil Stabilizers 9365 9189 9016 8914 8648 7920 7632 7516 7155 6909 6825 6578 6318 6117 6049 5979 5952 5853 5682
65 Shovels, Backhoes & Hydraulic Excavators 7653 7509 7368 7271 7124 7031 6820 6858 6685 6621 6543 6201 5869 5728 5582 5236 5310 5289 5225
70 Tractors, Crawlers & Attachments 8813 8647 8485 8378 8088 7713 7434 7454 7254 7037 6907 6653 6347 6177 6081 6058 6032 5960 5792
75 Tractor, Wheel 7583 7440 7300 7196 7050 6845 6678 6636 6442 6144 5876 5616 5400 5170 5055 4997 4906 4833 4695
80 Trenchers 9739 9556 9376 9243 9062 8835 8620 8565 8314 7930 7584 7248 6970 6466 6524 6450 6332 6223 6042
85 Trucks, Highway 6473 6351 6231 6131 5988 5648 5485 5366 5123 4965 4820 4638 4450 4356 4306 4216 4212 4307 4216
90 Trucks & Wagons - Off-Highway 8636 8473 8314 8172 8103 7940 7820 7785 7651 7392 7231 6896 6424 6095 6026 5931 5828 5715 5651
95 All Other Equipment 7628 7485 7344 7247 7063 6787 6582 6569 6375 6176 6033 5787 5450 5270 5195 5127 5112 5062 4993
100 All Tires & Tubes 4207 4128 4050 3991 4062 3929 3525 3343 3267 3025 2926 2759 2614 2487 2430 2401 2373 2371 2400
105 Marine Equipment 8844 8678 8515 8316 8216 8118 7941 7773 7466 7202 6905 6661 6436 6101 5846 5771 5645 5556 5513
EK = Economic Key E-1

E-1
EP 1110-1-8
(Vol. 8)
4/30/2014
EP 1110-1-8, Vol. 2
30 Apr 14 APPENDIX E
ECONOMIC INDEXES FOR CONSTRUCTION EQUIPMENT
KEY Note: Table 2-1 Equipment Rates are based on equipment purchased new in the year 2011
1997 1996 1995 1994 1993 1992 1991 1990 1989 1988 1987 1986 1985 1984 1983 1982 1981 1980
(EK) EQUIPMENT DIVISIONS
5 Air Equipment 2070 2063 2053 2012 2022 2008 1963 1956 1888 1801 1730 1720 1733 1683 1695 1668 1563 1630
10 Asphalt & Concrete Paving Equipment 3490 3390 3323 3248 3189 3092 3106 2967 2867 2793 2730 2687 2687 2611 2583 2620 2461 2296
15 Buckets 6888 6774 6672 6638 6663 6380 5901 5640 5314 4872 4767 4713 4640 4527 4471 4541 4313 3879
20 Cranes, Draglines & Clamshells - Crawler & Truck Mtd 5116 5013 4880 4783 4736 4540 4298 4152 3967 3688 3595 3485 3395 3339 3282 3213 3009 2782
25 Drills 3574 3518 3394 3320 3268 3196 3163 3069 2969 2807 2792 2786 2832 2803 2836 2810 2602 2265
30 Generators 4484 4511 4457 4343 4294 4234 4181 4116 3998 3773 3575 3514 3510 3400 3314 3236 3160 2817
35 Graders, Motor 5544 5466 5186 5088 4946 4655 4509 4359 4219 4010 3914 3759 3738 3645 3643 3561 3276 2992
40 Loaders, Track 5686 5606 5434 5257 5068 4816 4677 4555 4404 4163 3918 3770 3767 3791 3792 3655 3349 3061
45 Loaders, Wheel 5303 5251 5101 4988 4894 4758 4640 4532 4409 4235 4099 3991 3973 3944 3873 3788 3441 2938
50 Pile Driving Equipment 4892 4809 4700 4598 4539 4427 4305 4182 4029 3845 3745 3668 3626 3570 3519 3439 3208 2894
55 Rollers 5001 4950 4851 4719 4484 4460 4668 4630 4507 4412 4217 4151 4090 3926 3744 3431 3199 2913
60 Scrapers & Soil Stabilizers 5544 5466 5186 5088 4946 4655 4509 4359 4219 4010 3914 3759 3738 3645 3643 3561 3276 2992
65 Shovels, Backhoes & Hydraulic Excavators 5116 5013 4880 4783 4736 4540 4298 4152 3967 3688 3595 3485 3395 3339 3282 3213 3009 2782
70 Tractors, Crawlers & Attachments 5686 5606 5434 5257 5068 4816 4677 4555 4404 4163 3918 3770 3767 3791 3792 3655 3349 3061
75 Tractor, Wheel 4624 4540 4527 4484 4342 4270 4186 4123 4018 3936 3862 3820 3818 3656 3557 3530 3256 2927
80 Trenchers 5833 5749 5670 5509 5207 5015 4948 4886 4753 4679 4600 4586 4488 4431 4360 4097 3618 3153
85 Trucks, Highway 4241 4318 4293 4190 4025 3838 3669 3546 3495 3363 3299 3282 3139 3055 2934 2824 2638 2324
90 Trucks & Wagons - Off-Highway 5581 5440 5265 4979 4837 4797 4739 4617 4405 4094 3915 3840 3822 3786 3744 3662 3363 2964
95 All Other Equipment 4892 4809 4700 4598 4539 4427 4305 4182 4029 3845 3745 3668 3626 3570 3519 3439 3208 2894
100 All Tires & Tubes 2431 2475 2559 2517 2525 2524 2506 2470 2480 2399 2322 2340 2374 2421 2453 2552 2506 2369
105 Marine Equipment 5429 5245 5036 4951 4881 4679 4438 4271 4091 3920 3886 3863 3749 3633 3497 3391 3239 2922
EK = Economic Key E-2

E-2
EP 1110-1-8, Vol. 2
30EPApr
1110-1-8
14
(Vol. 8)
4/30/2014
APPENDIX F
TIRE DESCRIPTION AND TIRE COST
TUBE COST
EP CODE INDUSTRY CODE SIZE DESCRIPTION SIZE PLY (1) PER EACH
LT TRUCK/RECREATIONAL VEHICLE, RADIAL
WORKHORSE EXTRA GRIP RADIAL (Life = 5000 hrs )
ABAA3 LT265/75R16 10.40 x 16.00 10 TL $254
WRANGLER RADIAL AT (Life = 5000 hrs )
ABAC1 LT235/75R15 9.25 x 15.00 6 TL $216

ABAC2 31-1050R15 10.50 x 15.00 6 TL $177
SERVICE TRAILER - MARATHON RADIAL (Life = 5000 hrs )
ABBF1 ST175/80R13 7.00 x 13.00 4 TL $101

ABBF3 ST185/80R13 7.20 x 13.00 6 TL $128
ABBF5 ST205/75R14 8.00 x 14.00 6 TL $141
ABBF8 ST205/75R15 8.00 x 15.00 6 TL $143
ABBF6 ST215/75R14 8.50 x 14.00 6 TL $152
ABBF9 ST225/75R15 8.80 x 15.00 6 TL $154
ABBF10 ST225/75R15 8.80 x 15.00 8 TL $164
LT TRUCK/RECREATIONAL VEHICLE, BIAS
WORKHORSE RIB (Life = 5000 hrs )

ACBA2 700-15LT 8.30 x 15.00 8 TL $242
ACBA7 875-16.5LT 8.80 x 16.50 10 TL $281
ACBA4 750-16LT 8.90 x 16.00 10 TL $279
ACBA9 950-16.5LT 9.60 x 16.50 10 TL $308
TRACTION HI-MILER (Life = 5000 hrs )

ACBC1 6.70-15LT 7.50 x 15.00 6 TL $248
ACBC3 8-14.5LT 8.00 x 14.50 12 TL $189
ACBC4 9-14.5LT 9.50 x 14.50 12 TL $218
CUSTOM HI-MILER (Life = 5000 hrs )
ACBD1 12-16.5LT 12.10 x 16.50 12 TL $818
OVER-THE-ROAD TRUCK, COMMERCIAL, RADIAL
COMMERICAL RADIAL LT TRUCK (Life = 5000 hrs )
ADCA2 LT225/75R16 7.50 x 16.00 10 TL $299

ADCA17 8R19.5 8.00 x 19.50 10 TL $503
ADCA18 8R195 8.00 x 19.50 12 TL $343
(1) TT = includes tube, TL = no tube, NO = no tube F-1
F-1
EP 1110-1-8, Vol. 2
EP 1110-1-8
30
Apr 14
(Vol. 8)
4/30/2014
APPENDIX F
TUBE COST
ADCA4 LT215/85R16 8.50 x 16.00 10 TL $250

ADCA3 LT215/85R16 8.50 x 16.00 8 TL $245
ADCA1 750R16LT 8.70 x 16.00 8 TL $218
ADCA6 LT225/75R16 8.80 x 16.00 10 TL $204
ADCA19 225/70R195 8.85 x 19.50 12 TL $351
ADCA8 LT235/85R16 9.25 x 16.00 10 TL $213
ADCA21 245/70R195 9.65 x 19.50 14 TL $393
ADCA11 LT245/75R16 9.80 x 16.00 10 TL $221
COMMERCIAL RADIAL TRUCK TL (Life = 5000 hrs )
ADCB2 9R175 9.00 x 17.50 16 TL $520

ADCB5 9R22.5 9.00 x 22.50 12 TL $368
ADCB3 10R175 10.00 x 17.50 16 TL $559
ADCB7 10R22.5 10.00 x 22.50 14 TL $524
ADCB4 11R17.5 11.00 x 17.50 16 TL $506
ADCB8 11R22.5 11.00 x 22.50 16 TL $803
ADCB13 11R24.5 11.00 x 24.50 16 TL $855
ADCB10 12R22.5 12.00 x 22.50 16 TL $926
ADCB14 12R24.5 12.00 x 24.50 16 TL $959
LOW PROFILE RADIAL TRUCK TL (Life = 5000 hrs )

ADCC1 215/75R175 8.40 x 17.50 16 TL $549
ADCC5 245/75R22.5 9.60 x 22.50 14 TL $403
ADCC3 255/70R22.5 10.00 x 22.50 16 TL $486
ADCC2 265/70R19.5 10.40 x 19.50 14 TL $426
ADCC6 265/75R22.5 10.40 x 22.50 14 TL $489
ADCC4 275/70R22.5 10.80 x 22.50 16 TL $562
ADCC12 285/75R24.5 11.20 x 24.50 14 TL $491
ADCC8 295/75R22.5 11.60 x 22.50 16 TL $716
ADCC10 315/80R22.5 12.40 x 22.50 18 TL $1,134
SUPER SINGLE COMMERCIAL RADIAL TRUCK (Life = 5000 hrs )
ADCD1 385/65R22.5 15.10 x 22.50 18 TL $943

ADCD2 425/65R22.5 16.70 x 22.50 20 TL $1,058
ADCD3 445/65R22.5 17.50 x 22.50 20 TL $1,196
COMMERCIAL RADIAL TRUCK TT (Life = 5000 hrs )
ADCE1 825R15 8.25 x 15.00 14 TT $393

ADCE5 9.00R20 8.25 x 20.00 12 TT $513

F-2
EP 1110-1-8, Vol. 2
30EPApr
1110-1-8
14
(Vol. 8)
4/30/2014
APPENDIX F
TUBE COST
ADCE6 9.00R20 9.00 x 20.00 12 TT $538

ADCE3 1000R15 10.00 x 15.00 14 TT $568
ADCE7 1000R20 10.00 x 20.00 14 TT $606
ADCE13 10R22.5 10.00 x 22.50 12 TL $607
ADCE12 365/80R20 10.40 x 20.00 18 TT $1,305
ADCE9 1100R20 11.00 x 20.00 16 TT $703
ADCE10 1100R20 11.00 x 20.00 16 TT $887
ADCE14 1100R22 11.00 x 22.00 16 TT $834
ADCE15 1100R24 11.00 x 24.00 16 TT $833
ADCE11 1200R20 12.00 x 20.00 18 TT $858
ADCE17 1200R24 12.00 x 24.00 18 TT $950
FARM, FRONT
DYNA RIB F-2-M (Life = 5000 hrs )
AFED2 F-2M 1000-16 10.00 x 16.00 8 TL $350

AFED1 F-2M 11L-15 11.00 x 15.00 6 TL $338
AFED4 F-2M 1100-16 11.00 x 16.00 8 TL $449
AFED8 F-2M 1100-24 11.00 x 24.00 12 TL $1,015
AFED6 F-2M 14L-161 14.00 x 16.10 10 TL $884
AFED7 F-2M 165L-161 16.50 x 16.10 8 TL $1,128
SINGLE RIB FRONT TRACTOR F-1 (Life = 5000 hrs )
AFEE1 F-1 600-16 6.00 x 16.00 4 TT $251
FARM HIGHWAY SERVICE (Life = 5000 hrs )
AFEF2 I-1 95L-15FI 9.50 x 15.00 D TL $282
FARM UTILITY (Life = 5000 hrs )
AFEG7 I-1 750-14 7.50 x 14.00 4 TL $233

AFEG14 I-1 760-15 7.60 x 15.00 8 TL $203
AFEG8 I-1 85L-14 8.50 x 14.00 6 TL $210
AFEG1 I-1 95L-14 9.50 x 14.00 6 TT $205
AFEG17 I-1 95L-15 9.50 x 15.00 12 TL $302
AFEG18 I-1 1000-15 10.00 x 15.00 8 TL $356
AFEG11 I-1 11L-14 11.00 x 14.00 8 TL $271
AFEG22 I-1 11L-15 11.00 x 15.00 10 TL $310
AFEG20 I-1 11L-15 11.00 x 15.00 8 TL $227
AFEG34 I-1 11L-16 11.00 x 16.00 10 TL $312

F-3
EP 1110-1-8, Vol. 2
EP 1110-1-8
30
Apr 14
(Vol. 8)
4/30/2014
APPENDIX F
TUBE COST
AFEG25 I-1 125L-15 12.50 x 15.00 12 TL $388

AFEG30 I-1 125L-16 12.50 x 16.00 12 TL $451
AFEG29 I-1 125L-16 12.50 x 16.00 8 TL $398
AFEG28 I-1 14L-161 14.00 x 16.10 12 TL $681
AFEG31 I-1 165L-161 16.50 x 16.10 10 TL $677
AFEG32 I-1 19L-161 19.00 x 16.10 10 TL $891
AFEG27 I-1 215L-161 21.50 x 16.10 14 TL $1,449
FOUR RIB FRONT TRACTOR F-2-M (Life = 5000 hrs )
AFEH1 F-2M 750-16 7.50 x 16.00 6 TT $232

AFEH3 F-2M 1000-16 10.00 x 16.00 8 TT $323
AFEH4 F-2M 1100-16 11.00 x 16.00 8 TT $427
IMPLEMENT RIB (Life = 5000 hrs )

TFEK11 I-1 4.00-18 4.00 x 18.00 4 TT $171
AFEK4 I-1 500-15 5.00 x 15.00 4 TL $126
AFEK16 I-1 590-15 5.90 x 15.00 4 TL $171
AFEK6 I-1 600-16 6.00 x 16.00 6 TL $175
AFEK7 I-1 650-16 6.50 x 16.00 6 TL $175
AFEK5 I-1 670-15 6.70 x 15.00 6 TL $169
AFEK9 I-1 750-16 7.50 x 16.00 10 TL $292
AFEK13 I-1 900-24 9.00 x 24.00 8 TL $637
AFEK14 I-1 1125-28 11.25 x 28.00 12 TL $1,185
LABORER F-3 (Life = 5000 hrs )
AFEL6 F-3 145/75-161 5.70 x 16.10 10 TL $785

AFEL2 F-3 11L-15 11.00 x 15.00 10 TL $349
AFEL4 F-3 11L-16 11.00 x 16.00 10 TL $325
AFEL5 F-3 11L-16 11.00 x 16.00 12 TL $372
MULTI-RIB F-3 (Life = 5000 hrs )
AFEM1 F-3 900-10 9.00 x 10.00 10 TT $236

TFEM2 F-3 1100-16 11.00 x 16.00 12 TL $564
SMOOTH (Life = 5000 hrs )

AFEN1 I-1 169-30 16.90 x 30.00 6 TL $1,354
SMOOTH IMP (Life = 5000 hrs )
AFEO1 4.00-8 4.00 x 8.00 4 TL $127

AFEO3 600-16 6.00 x 16.00 10 TL $394
F-4
EP 1110-1-8, Vol. 2
30EP 1110-1-8
Apr 14
(Vol. 8)
4/30/2014
APPENDIX F
TUBE COST
AFEO2 11L-15 11.00 x 15.00 10 TL $378
SOFTRAC II (Life = 5000 hrs )
AFEP1 I-2 165L-161 16.50 x 16.10 6 TL $760

AFEP3 I-2 215L-161 21.50 x 16.10 10 TL $1,734
SUPER RIB F-2 (Life = 5000 hrs )
TFER1 F-2 400-12 4.00 x 12.00 4 TT $119
COMPACT UTILITY R-1 (Life = 5000 hrs )
TFES2 5-12 5.00 x 12.00 4 TL $127

AFES1 7-16 7.00 x 16.00 6 TL $277
SURE GRIP IMPLEMENT (Life = 5000 hrs )
AFET1 I-3 105/80-18 10.50 x 18.00 10 TL $722

AFET2 I-3 12.5/80-18 12.50 x 18.00 10 TL $776
SURE GRIP LUG (Life = 5000 hrs )
AFEU2 I-3 105/80-18 10.50 x 18.00 10 TL $594

AFEU1 I-3 124-16 12.40 x 16.00 4 TL $880
AFEU3 I-3 12.5/80-18 12.50 x 18.00 14 TL $720
SURE GRIP TRACTION (Life = 5000 hrs )
AFEV1 I-3 670-15 6.70 x 15.00 4 TT $224

AFEV5 I-3 750-16 7.50 x 16.00 4 TL $345
AFEV2 I-3 750-18 7.50 x 18.00 4 TT $341
AFEV3 I-3 750-20 7.50 x 20.00 4 TT $386
AFEV4 I-3 760-15 7.60 x 15.00 6 TL $297
TRACTION IMPLEMENT (Life = 5000 hrs )
AFEW1 I-3 500-15 5.00 x 15.00 4 TL $216

AFEW2 I-3 590-15 5.90 x 15.00 4 TL $231
TRIPLE RIB HD (Life = 5000 hrs )
AFEX8 F-2 550-16 5.50 x 16.00 6 TT $137

AFEX10 F-2 600-16 6.00 x 16.00 6 TT $156
AFEX11 F-2 650-16 6.50 x 16.00 6 TT $195
AFEX4 F-2 75L-15 7.50 x 15.00 6 TT $192
AFEX18 F-2 750-16 7.50 x 16.00 6 TL $229
AFEX13 F-2 750-16 7.50 x 16.00 8 TT $237

F-5
EP 1110-1-8, Vol. 2
EP 1110-1-8
30
Apr 14
(Vol. 8)
4/30/2014
APPENDIX F
TUBE COST
AFEX14 F-2 750-18 7.50 x 18.00 6 TT $265

AFEX5 F-2 95L-15 9.50 x 15.00 8 TT $305
AFEX16 F-2 1000-16 10.00 x 16.00 8 TL $377
AFEX6 F-2 11L-15 11.00 x 15.00 8 TT $338
AFEX17 F-2 1100-16 11.00 x 16.00 8 TL $474
TRIPLE RIB R/S F-2 (Life = 5000 hrs )

AFEY2 F-2 400-15 4.00 x 15.00 4 TT $164
AFEY1 F-2 500-15 5.00 x 15.00 4 TT $156
DURATORQUE R-1 (Life = 5000 hrs )
AFFU3 R-1 8-16 8.00 x 16.00 6 TL $345
FARM, REAR
ALL TRACTION R-3 (Life = 5000 hrs )
AGFA1 R-3 750-16 7.50 x 16.00 4 TT $322
ALL WEATHER R-3 (Life = 5000 hrs )
AGFB2 R-3 95-24 9.50 x 24.00 4 TT $584

AGFB7 R-3 136-161 13.60 x 16.10 8 TL $999
AGFB5 R-3 136-28 13.60 x 28.00 6 TT $1,087
AGFB3 R-3 149-24 14.90 x 24.00 6 TL $1,065
AGFB4 R-3 169-24 16.90 x 24.00 6 TL $1,248
AGFB8 R-3 184-161 18.40 x 16.10 8 TL $1,275
AGFB10 R-3 184-26 18.40 x 26.00 12 TL $1,476
AGFB11 R-3 231-26 23.10 x 26.00 10 TL $2,309
AGFB12 R-3 231-26 23.10 x 26.00 12 TL $2,421
AGFB14 R-3 245-32 24.50 x 32.00 12 TL $3,827
AGFB13 R-3 28L-26 28.00 x 26.00 16 TL $3,371
AGFB15 R-3 305L-32 30.50 x 32.00 12 TL $4,513
AGFB16 R-3 305L-32 VA 30.50 x 32.00 16 TL $5,741
DT 800 RADIAL R-1W (Life = 5000 hrs )
AGFE1 R-1W 320/90R42 12.60 x 42.00 139A8 TL $2,257

AGFE3 R-1W 320/90R50 12.60 x 50.00 148A8 TL $2,952
AGFE2 R-1W 380/90R46 14.90 x 46.00 149A8 TL $2,913
AGFF1 R-1W 380/70R24 14.90 x 24.00 125A8 TL $2,231

F-6
EP 1110-1-8, Vol. 2
30EP 1110-1-8
Apr 14
(Vol. 8)
4/30/2014
APPENDIX F
TUBE COST
AGFF2 R-1W 420/70R28 16.50 x 28.00 133A8 TL $3,111

AGFF3 R-1W 480/70R30 18.90 x 30.00 152A8 TL $3,159
AGFG2 R-1W 600/65R28 23.60 x 28.00 154A8/B TL $3,869

AGFG1 R-1W 620/75R26 24.40 x 26.00 166A8 TL $6,478
AGFG5 R-1W 620/70R42 24.40 x 42.00 UK TL $4,477
AGFG3 R-1W 650/75R34 25.60 x 34.00 UK TL $6,124
AGFG4 R-1W 710/70R38 27.90 x 38.00 UK TL $4,870
DYNA TORQUE RADIAL R-1 (Life = 5000 hrs )
TGFH5 R-1 320/85R34 12.60 x 34.00 132D TL $1,796

AGFH7 R-1 380/85R30 14.90 x 30.00 X3 TL $2,112
AGFH9 R-1 380/85R34 14.90 x 34.00 X3 TL $2,358
AGFH15 R-1 380/85R46 14.90 x 46.00 X3 TL $2,801
TGFH6 R-1 385/85R34 15.20 x 34.00 141G TL $2,358
AGFH16 R-1 420/80R46 16.50 x 46.00 UK TL $3,817
AGFH8 R-1 420/90R30 16.90 x 30.00 X3 TT $2,394
TGFH2 R-1 480/85R26 18.40 x 26.00 X2 TL $2,367
AGFH10 R-1 480/80R38 18.40 x 38.00 14 TL $2,126
AGFH17 R-1 480/80R46 18.40 x 46.00 X3 TL $3,269
AGFH12 R-1 520/85R38 20.80 x 38.00 14 TL $2,758
AGFH14 R-1 520/85R42 20.80 x 42.00 14 TL $2,992
DYNA TORQUE II R-1 (Life = 5000 hrs )
AGFJ29 R-1 112-16 11.20 x 16.00 4 TL $522

AGFJ6 R-1 136-24 13.60 x 24.00 8 TT $1,080
AGFJ41 R-1 136-28 13.60 x 28.00 10 TL $1,377
AGFJ7 R-1 149-24 14.90 x 24.00 6 TL $835
AGFJ31 R-1 149-24 14.90 x 24.00 8 TL $961
AGFJ42 R-1 149-28 14.90 x 28.00 10 TL $1,805
AGFJ8 R-1 169-24 16.90 x 24.00 6 TT $1,033
AGFJ39 R-1 169-26 16.90 x 26.00 10 TL $2,257
AGFJ43 R-1 169-28 16.90 x 28.00 10 TL $2,084
AGFJ37 R-1 169-34 16.90 x 34.00 6 TT $1,260
AGFJ23 R-1 169-38 16.90 x 38.00 14 TL $2,245
AGFJ40 R-1 184-26 18.40 x 26.00 12 TL $1,810
AGFJ18 R-1 184-34 18.40 x 34.00 8 TT $1,448

F-7
EP 1110-1-8, Vol. 2
EP 1110-1-8
30
Apr 14
(Vol. 8)
4/30/2014
APPENDIX F
TUBE COST
AGFJ24 R-1 184-38 18.40 x 38.00 8 TT $1,511

AGFJ19 R-1 208-34 20.80 x 34.00 8 TT $2,518
AGFJ25 R-1 208-38 20.80 x 38.00 8 TT $2,016
AGFJ27 R-1 208-42 20.80 x 42.00 10 TL $3,385
AGFJ45 R-1 231-26 23.10 x 26.00 12 TL $2,552
AGFJ20 R-1 231-34 23.10 x 34.00 8 TT $2,821
AGFJ35 R-1 245-32 24.50 x 32.00 12 TL $3,184
AGFJ34 R-1 28L-26 28.00 x 26.00 12 TL $3,241
AGFJ36 R-1 305L-32 30.50 x 32.00 14 TL $4,831
INDUSTRIAL SURE GRIP R-4 (Life = 5000 hrs )
AGFK1 R-4 169-30 16.90 x 30.00 10 TT $2,868

AGFK3 R-4 184-28 18.40 x 28.00 12 TL $1,587
IT510 RADIAL R4 (Life = 5000 hrs )
AGFL3 R-4 195LR24 19.50 x 24.00 UK TL $2,585
IT525 RADIAL R4 (Life = 5000 hrs )
AGFM1 R-4 149-24 14.90 x 24.00 8 TL $962

AGFM4 R-4 169-24 16.90 x 24.00 10 TL $978
AGFM12 R-4 169-28 16.90 x 28.00 10 TL $1,250
AGFM6 R-4 175L-24 17.50 x 24.00 10 TL $1,095
AGFM5 R-4 184-24 18.40 x 24.00 12 TL $1,422
AGFM7 R-4 195L-24 19.50 x 24.00 10 TL $1,369
AGFM8 R-4 195L-24 19.50 x 24.00 12 TL $1,536
AGFM9 R-4 21L-24 21.00 x 24.00 12 TL $1,846
AGFM11 R-4 21L-24 21.00 x 24.00 16 TL $2,138
AGFM14 R-4 21L-28 21.00 x 28.00 14 TL $2,257
POWER TORQUE R-1 (Life = 5000 hrs )
AGFN1 R-1 6-12 6.00 x 12.00 4 TL $129
SPECIAL SURE GRIP R-2-0 (Life = 5000 hrs )
AGFO2 R-2 149-24 14.90 x 24.00 6 TL $1,989

AGFO11 R-2 184-26 18.40 x 26.00 10 TL $2,000
AGFO8 R-2 184-38 18.40 x 38.00 8 TL $2,868
AGFO12 R-2 VA500/95D32 19.70 x 32.00 20 TL $5,608
AGFO10 R-2 208-38 20.80 x 38.00 8 TL $2,978
AGFO3 R-2 231-26 23.10 x 26.00 10 TL $3,204

F-8
EP 1110-1-8, Vol. 2
30EP 1110-1-8
Apr 14
(Vol. 8)
4/30/2014
APPENDIX F
TUBE COST
AGFO4 R-2 28L-26 28.00 x 26.00 12 TL $4,459

AGFO6 R-2 305L-32 30.50 x 32.00 14 TL $5,529
SPECIAL SURE GRIP RADIAL R-2-0 (Life = 5000 hrs )
AGFP8 R-2 320/90R46 12.60 x 46.00 TL $2,914

AGFP9 R-2 340/85R46 13.40 x 46.00 UK TL $3,150
AGFP6 R-2 520/85R42 20.80 x 42.00 X2 TL $4,845
SUPER TRACTION RADIAL R-1W (Life = 5000 hrs )
AGFQ3 R-1W 260/80R20 10.20 x 20.00 8 TL $1,242

TGFQ15 R-1W 340/85R28 13.60 x 38.00 UK TL $2,351
AGFQ20 R-1W 149R24 14.90 x 24.00 X2 TL $2,438
TGFQ7 R-1W 380/85R28 14.90 x 28.00 UK TL $1,785
AGFQ9 R-1W 149R30 14.90 x 30.00 UK TL $2,421
AGFQ5 R-1W 169R26 16.90 x 26.00 UK TL $3,611
AGFQ8 R-1W 169R28 16.90 x 28.00 UK TL $2,598
AGFQ10 R-1W 169R30 16.90 x 30.00 UK TL $2,611
AGFQ11 R-1W 184R26 18.40 x 26.00 UK TL $2,720
AGFQ12 R-1W 460/85R30 18.40 x 30.00 UK TL $3,593
AGFQ14 R-1W 460/85R34 18.40 x 34.00 UK TL $4,036
AGFQ16 R-1W 184R38 18.40 x 38.00 UK TL $2,611
AGFQ18 R-1W 184R42 18.40 x 42.00 UK TL $3,200
AGFQ17 R-1W 208R38 20.80 x 38.00 UK TL $3,397
AGFQ13 R-1W 800/65R32 31.50 x 32.00 UK TL $5,647
DURATORQUE R-1 (Life = 5000 hrs )
AGFU1 R-1 149-28 14.90 x 28.00 6 TT $806

AGFU2 R-1 169-30 16.90 x 30.00 6 TT $1,015
AGFU3 R-1 184-30 18.40 x 30.00 6 TT $1,261
AGFU5 R-1 184-38 18.40 x 38.00 8 TT $1,519
FARM, TERRA - 20" UP
SFT105 (Life = 5000 hrs )

AHGA2 HF-1 54-3100-26 31.00 x 26.00 10 TL $2,450
SOF TRAC (Life = 5000 hrs )
AHGB3 HF-1 38-1400-20 14.00 x 20.00 4 TL $729

AHGB2 HF-1 41-1400-20 14.00 x 20.00 4 TL $780

F-9
EP 1110-1-8, Vol. 2
EP 1110-1-8
30
Apr 14
(Vol. 8)
4/30/2014
APPENDIX F
TUBE COST
AHGB1 HF-1 44-1800-20 18.00 x 20.00 4 TL $1,088
SUPER TERRA GRIP (Life = 5000 hrs )
AHGC1 HF-2 38-1400-20 14.00 x 20.00 8 TL $1,065

AHGC11 HF-2 1000/50R25 43.00 x 25.00 20 TL $9,859
SUPER TERRA GRIP XT (Life = 5000 hrs )
AHGD5 HF-3 48-3100-20 31.00 x 20.00 12 TL $3,388

AHGD6 HF-3 1000/50R25 43.00 x 25.00 10 TL $8,173
AHGD7 HF-3 1050/50R32 44.00 x 32.00 16 TL $11,917
TUNDRA GRIP (Life = 5000 hrs )
AHGF2 HF-1 1050/50R25 44.00 x 25.00 16 TL $12,242

AHGF1 HF-1 66-4400-25 44.00 x 25.00 20 TL $11,752
FARM, SPECIALTY
SOFTRAC (Life = 5000 hrs )
TJHB2 18-6.50-8/2 6.50 x 17.20 2.0 TL $43

TJHB3 18-850-10 8.50 x 10.00 4 TL $151
AJHB1 HF-1 25-850-14 8.50 x 14.00 6 TL $284
AJHB5 HF-1 27-850-15 8.50 x 15.00 4 TL $289
AJHB4 HF-1 25-1050-15 10.50 x 15.00 4 TL $303
AJHB6 HF-1 27-1050-15 10.50 x 15.00 4 TL $359
AJHB7 HF-1 29-1250-15 12.50 x 15.00 4 TL $391
AJHB10 HF-1 31-1250-15 12.50 x 15.00 4 TL $433
AJHB11 HF-1 33-1250-15 12.50 x 15.00 4 TL $506
AJHB8 HF-1 31-1350-15 13.50 x 15.00 4 TL $476
AJHB9 HF-1 31-1550-15 15.50 x 15.00 4 TL $550
SUPER TERRA GRIP (Life = 5000 hrs )
AJHC3 HF-2 29-1250-15 12.50 x 15.00 6 TL $401

AJHC6 HF-2 31-1550-15 15.50 x 15.00 8 TL $704
AJHC7 HF-2 38-2000-16.1 20.00 x 16.00 8 TL $1,436
SURE GRIP LUG (Life = 5000 hrs )
AJHD9 HF-2 27-850-15 8.50 x 15.00 6 TL $331

AJHD1 10-16.5 10.00 x 16.50 6 TL $359
AJHD10 HF-2 27-1050-15 10.50 x 15.00 6 TL $317
AJHD4 12-165 12.00 x 16.50 10 TL $418

F-10
EP 1110-1-8, Vol. 2
30EP 1110-1-8
Apr 14
(Vol. 8)
4/30/2014
APPENDIX F
TUBE COST
AJHD3 12-165 12.00 x 16.50 8 TL $381

AJHD5 I-3 14-17.5 14.00 x 17.50 10 TL $741
AJHD6 I-3 15-19.5 15.00 x 19.50 12 TL $858
IT 323 (Life = 5000 hrs )
AJHE1 10-165 10.00 x 16.50 8 TL $368

AJHE3 12-165 12.00 x 16.50 10 TL $467
AJHE4 31-1550-15 15.50 x 15.00 8 TL $1,233
POWER RIB (Life = 5000 hrs )
TJHJ1 18-850-8 8.50 x 8.00 4 TL $122

TJHJ2 20X10.00-10 8.80 x 20.80 4 TL $81
RALLY (Life = 5000 hrs )
TJHK1 480-8 4.80 x 8.00 6.0 TL $59

TJHK2 18X9.50-8 9.50 x 18.50 6.0 TL $72
TERRA RIB (Life = 5000 hrs )
AJHM2 HF-1 25-750-15 7.50 x 15.00 6 TL $213

AJHM4 HF-1 27-950-15 9.50 x 15.00 10 TL $325
AJHM6 HF-1 31-1350-15 13.50 x 15.00 8 TL $546
ATV (Life = 5000 hrs )
TJHN1 AT21-7-10 7.00 x 10.00 X3 TL $127

TJHN3 AT23-8-11 8.00 x 11.00 6 TL $140
TJHN5 AT24-9-11 9.00 x 11.00 6 TL $162
TRACKER ATT (Life = 5000 hrs )

TJHT1 AT24-8-11 8.00 x 11.00 X2 TL $185
TJHT2 AT24-10-11 10.00 x 11.00 X2 TL $172
INDUSTRIAL, MINE SERVICE
HARD ROCK LUG MINE & INDUSTRIAL (Life = 5000 hrs )
TKJC1 10.00-20 10.00 x 20.00 16.0 TT $1,010
XTRA TRACTION LUG (Life = 5000 hrs )
AKJD2 825-15 8.25 x 15.00 16 TT $945

AKJD7 24x12x12 12.00 x 12.00 24 TL $606
AKJD6 35-15x15(14.50L-15) 15.00 x 15.00 28 TL $1,636

F-11
EP 1110-1-8, Vol. 2
EP 1110-1-8
30
Apr 14
(Vol. 8)
4/30/2014
APPENDIX F
TUBE COST
XTRA TRACTION GRIP (Life = 5000 hrs )
AKJE1 32x15-15 15.00 x 15.00 24 TL $1,503
OFF-THE-ROAD, MED & HEAVY COMMERCIAL, RADIAL
G-2 GRADER SERVICE - RL2F, SG2B (Life = 3200 hrs )
AMLA1 G2 14.00R24 14.00 x 24.00 X1 TL $1,688
E-2 HAULAGE SERVICE - RL2F/GP2B RL2+ (Life = 2800 hrs )
AMLB1 E/L/G3 17.5R25 17.50 x 25.00 X1 TL $1,959

AMLB8 L5 1800R25 18.00 x 25.00 X2 TL $5,904
AMLB2 E/L/G3 20.5R25 20.50 x 25.00 X1 TL $2,652
AMLB9 E/L/G3 20.5R25 20.50 x 25.00 X2 TL $2,652
AMLB15 E4 21.00R35 21.00 x 35.00 X2 TL $9,855
AMLB3 E/L/G3 23.5R25 23.50 x 25.00 X1 TL $3,213
AMLB10 E/L/G3 23.5R25 23.50 x 25.00 X2 TL $3,213
AMLB22 E/L 3 29.5R25 29.50 x 25.00 X2 TL $6,606
AMLB21 E/L/G 3+T 295R29 29.50 x 29.00 X2 TL $8,791
FMLB23 E3 40.5/75R39 40.50 x 39.00 X2 TL $13,164
E-3 HAULAGE SERVICE - ROCK DESIGN RL3, RL3J, R (Life = 2800 hrs )
AMLC3 E3+ 1800R33 18.00 x 33.00 X3 TL $6,127
AMLC5 E3+ 24.00R35 24.00 x 35.00 X2 TL $9,850
AMLC6 E3 29.5R29 29.50 x 29.00 X2 TL $8,398
FMLC8 E3 37.25R35 37.35 x 35.00 X2 TL $10,440
E-4 RL4J/RL4 & RL4H/RL4 E4 (Life = 5000 hrs )

AMLD2 E4 14.00R24 14.00 x 24.00 X3 TL $2,910
AMLD3 E4 14.00R25 14.00 x 25.00 X3 TL $2,910
AMLD4 E4 1800R25 18.00 x 25.00 X2 TL $4,843
AMLD14 E4 21.00R35 21.00 x 35.00 X2 TL $9,855
AMLD7 E4 27.00R49 27.00 x 49.00 X2 TL $21,706
FMLD9 E4 33.00R51 33.00 x 51.00 X2 TL $17,703
FMLD11 E4 37.00R57 37.00 x 57.00 X2 TL $24,058
MOBILE CRANE (Life = 5000 hrs )
AMLF1 E/L/G3 445/95R25 17.50 x 25.00 UK TL $2,497

AMLF3 E/L/G3 525/80R25 (20.5R25) 20.60 x 25.00 UK TL $2,652

F-12
EP 1110-1-8, Vol. 2
30EP 1110-1-8
Apr 14
(Vol. 8)
4/30/2014
APPENDIX F
TUBE COST
SPECIAL SERVICE - AT2A (Life = 5000 hrs )
AMLH1 E/L/G 3 14.00R20 14.00 x 20.00 18 TL $2,110

AMLH3 E/L/G 3 16.00R20 16.00 x 20.00 22 TL $2,519
AMLH2 E/L/G3 17.5R25 17.50 x 25.00 X1 TL $1,959
E-3 ROCK SERVICE SUPER HARD ROCK LUG (Life = 2800 hrs )
AMMF1 L3 26.5-25 26.50 x 25.00 24 TL $5,445
OFF-THE-ROAD, MED & HEAVY COMMERCIAL, BIAS
E-1 HRR 1A (Life = 2500 hrs )
ANMB1 E3 1400-24 14.00 x 24.00 20 TT $2,327
E-2 TRACTION EARTHMOVER SURE GRIP (Life = 2800 hrs )

ANMC3 E7 18.00-25 18.00 x 25.00 16 TL $2,335
E-3 ROCK SERVICE HARD ROCK LUG/HRL WC (Life = 2800 hrs )
ANME1 E3 12.00-20 12.00 x 20.00 20 TT $1,309

ANME2 E3 12.00-24 12.00 x 24.00 16 TT $1,454
ANME3 E3 14.00-24 14.00 x 24.00 28 TT $2,187
ANME6 E3 1600-25 16.00 x 25.00 28 TL $3,897
E-3 ROCK SERVICE SUPER HARD ROCK LUG (Life = 2800 hrs )
TNMF4 L5 29.5-25 29.50 x 25.00 28 TL $10,398

TNMF5 L4 29.5-29 29.50 x 29.00 28 TL $9,053
TNMF6 E3 29.5-29 29.50 x 29.00 34 TL $8,175
E-3 ROCK SERVICE SHRL8 (Life = 2800 hrs )

TNMG8 E-3 29.5-25 29.50 x 25.00 28.0 TL $7,460
TNMG9 E-3 29.5-25 29.50 x 25.00 34.0 TL $8,276
TNMG7 E-3/L-3 33.25-29 33.25 x 29.00 38.0 TL $10,640
TNMG6 E3 33.25-35 33.25 x 35.00 38 TL $12,783
ANMG7 E3 37.25-35 37.25 x 35.00 36 TL $12,449
ANMG9 E3 375-39 37.50 x 39.00 52 TL $15,301
E-3 ROCK SERVICE ELV3A, ELV4B, ELV4/5A (Life = 2800 hrs )
ANMH9 IND 3 1800-25 18.00 x 25.00 40 TL $4,403

ANMH4 IND 5S 18.00-25 18.00 x 25.00 40 TL $5,596

F-13
EP 1110-1-8, Vol. 2
EP 1110-1-8
30
Apr 14
(Vol. 8)
4/30/2014
APPENDIX F
TUBE COST
E-3 ROCK SERVICE HRL 3F (Life = 2800 hrs )
ANMJ5 E3 37.25-35 37.25 x 35.00 36 TL $13,105

ANMJ6 E3 3725-35 37.25 x 35.00 36 TL $13,105
ANMJ2 E3 3725-35 37.25 x 35.00 36 TL $13,105
E-3 ROCK SERVICE WRL 3A (Life = 2800 hrs )
ANML1 E3 14.00-20 14.00 x 20.00 24 TT $1,927

ANML2 E3 14.00-24 14.00 x 24.00 24 TT $2,042
E-4 ROCK SERVICE HRL 4B (Life = 5000 hrs )
ANMN1 E4 16.00-25 16.00 x 25.00 28 TL $4,169

ANMN4 E4 21.00-35 21.00 x 35.00 36 TL $9,291
ANMN5 E4 24.00-35 24.00 x 35.00 42 TL $9,667
ANMN9 E4 36.00-51 36.00 x 51.00 58 TL $26,709
E-7 FLOTATION TYPE SAND RIB SRB 7A (Life = 3000 hrs )
TNMQ1 E7 14.00-20 14.00 x 20.00 10 TL $1,448

TNMQ2 E7 16.00-24 16.00 x 24.00 12 TL $2,852
TNMQ3 E7 18.00-25 18.00 x 25.00 16 TL $3,701
E-7 FLOTATION TYPE PAVER TIRE (Life = 3000 hrs )

ANMR1 E7 1600-24 16.00 x 24.00 12 TL $1,779
G-2 SGG2A (Life = 3200 hrs )
TNMT10 G2 13.00-24 13.00 x 24.00 12 TL $860

TNMT6 G-2 14.00-24 14.00 x 24.00 14 TL $1,055
TNMT8 G2 16.00-24 16.00 x 24.00 16 TL $2,133
G-2 SGLDL 2A L2 (Life = 3200 hrs )
ANMV3 L2/G2 17.5-25 17.50 x 25.00 12 TL $921

ANMV2 L2/G2 17.5-25 17.50 x 25.00 12 TL $921
ANMV4 L2/G2 17.5-25 17.50 x 25.00 16 TL $1,021
ANMV5 L2/G2 17.5-25 17.50 x 25.00 20 TL $1,121
G-2 SGLEL 2A ES/L2/G2 (Life = 3200 hrs )

TNMW1 L2 20.5-25 20.50 x 25.00 12 TL $1,842
TNMW2 L2 20.5-25 20.50 x 25.00 16 TL $1,986
TNMW5 L2 23.5-25 23.50 x 25.00 16 TL $2,676

F-14
EP 1110-1-8, Vol. 2
30EP 1110-1-8
Apr 14
(Vol. 8)
4/30/2014
APPENDIX F
TUBE COST
G-3 RKG 3A (Life = 3200 hrs )
TNMX1 G2 14.00-24 14.00 x 24.00 14 TL $1,055
L-3 DOZER/LOADER SERVICE ROCK SERVICE E3/L3 (Life = 3200 hrs )
ANNB1 E/G/L3 205-25 20.50 x 25.00 20 TL $1,430

ANNB5 E/L 3 23.5-25 23.50 x 25.00 16 TL $4,233
ANNB2 E/G/L3 235-25 23.50 x 25.00 16 TL $4,233
ANNB6 E/L 3 23.5-25 23.50 x 25.00 20 TL $4,458
L-3 DOZER/LOADER SERVICE ROCK SHRL DL (Life = 3200 hrs )
TNNC3 L4 29.5-25 29.50 x 25.00 28 TL $9,034
L-3 DOZER/LOADER SERVICE ROCK HRL DL 3A & 3F (Life = 3200 hrs )
ANND2 L/G3 265-25 26.50 x 25.00 20 TL $6,352
L-4 DOZER/LOADER SERVICE ROCK DEEP TREAD N (Life = 5000 hrs )
TNNG1 L5 35/65-33 35.00 x 33.00 42 TL $17,577
L-5 DOZER/LOADER SERVICE ROCK SUPER XTRA T (Life = 8000 hrs )
TNNL2 L4 35/65-33 35.00 x 33.00 42 TL $15,843

TNNL4 L5 41.25/70-39 41.25 x 39.00 42 TL $27,656
ANNL7 L5 45/65-45 45.00 x 45.00 58 TL $29,758
L-5 DOZER/LOADER SERVICE SMOOTH SMO SL5B (Life = 8000 hrs )
ANNN3 IND3 18.00-25 18.00 x 25.00 40 TL $4,403
L-5 DOZER/LOADER SERVICE SMOOTH SUPER XTRA (Life = 8000 hrs )
TNNO1 L5S 295-25 29.50 x 25.00 28 TL $12,967
INDUSTRIAL, SOLID
SOLID, HIGH PERFORMANCE, OIL RESISTANT/STATI (Life = 5000 hrs )
IPPO5 10x3x6-1/4 Grip 3.00 x 10.00 NO $399

IPPO4 10x3-1/2x6 3.50 x 10.00 NO $432
IPPO18 12x3-1/2x8 3.50 x 12.00 NO $441
IPPO23 13x3-1/2x8 3.50 x 13.00 NO $501
IPPO32 15x3-1/2x11-1/4 3.50 x 15.00 NO $473
IPPO1 8-1/2x4x4 4.00 x 8.50 NO $546
IPPO10 10x4x6-1/2 4.00 x 10.00 NO $377
IPPO6 10x4x6-1/4 4.00 x 10.00 NO $440

F-15
EP 1110-1-8, Vol. 2
EP 1110-1-8
30
Apr 14
(Vol. 8)
4/30/2014
APPENDIX F
TUBE COST
IPPO19 12x4x8 4.00 x 12.00 NO $482

IPPO47 16-1/4x4x11-1/4 Lug 4.00 x 16.25 NO $595
IPPO30 14x4-1/2x8 4.50 x 14.00 NO $655
IPPO40 16x4-1/2x10-1/2 Lug 4.50 x 16.00 NO $711
IPPO2 9-5-5 Grip 5.00 x 9.00 NO $408
IPPO12 10x5x6-1/2 5.00 x 10.00 NO $392
IPPO7 10x5x6-1/4 5.00 x 10.00 NO $439
IPPO13 10-1/2x5x5 5.00 x 10.50 NO $640
IPPO31 14x5x10 5.00 x 14.00 NO $600
IPPO33 15x5x11-1/4 5.00 x 15.00 NO $578
IPPO38 15-1/2x5x10 5.00 x 15.50 NO $672
IPPO41 16x5x10-1/2 5.00 x 16.00 NO $742
IPPO48 16-1/4x5x11-1/4 5.00 x 16.25 NO $642
IPPO53 17x5x12-1/8 5.00 x 17.00 NO $732
IPPO63 18x5x14 5.00 x 18.00 NO $653
IPPO58 18x5x12-1/8 5.00 x 18.00 NO $777
IPPO68 20x5x16 5.00 x 20.00 NO $870
IPPO73 21x5x15 5.00 x 21.00 NO $904
IPPO79 22x5x16 5.00 x 22.00 NO $966
IPPO8 10x6x6-1/4 6.00 x 10.00 NO $530
IPPO14 10-1/2x6x5 6.00 x 10.50 NO $666
IPPO34 15x6x11-1/4 6.00 x 15.00 NO $614
IPPO42 16x6x10-1/2 6.00 x 16.00 NO $833
IPPO49 16-1/4x6x11-1/4 6.00 x 16.25 NO $757
IPPO59 18x6x12-1/8 6.00 x 18.00 NO $874
IPPO69 20x6x16 6.00 x 20.00 NO $925
IPPO74 21x6x15 6.00 x 21.00 NO $1,131
IPPO80 22x6x16 6.00 x 22.00 NO $1,141
IPPO22 12-6-1/2x8 6.50 x 12.00 NO $668
IPPO9 10x7x6-1/4 7.00 x 10.00 NO $617
IPPO35 15x7x11-1/4 7.00 x 15.00 NO $765
IPPO43 16x7x10-1/2 7.00 x 16.00 NO $955
IPPO50 16-1/4x7x11-1/4 7.00 x 16.25 NO $943
IPPO60 18x7x12-1/8 7.00 x 18.00 NO $911
IPPO70 20x7x16 7.00 x 20.00 NO $1,119
IPPO75 21x7x15 7.00 x 21.00 NO $1,161
IPPO81 22x7x16 7.00 x 22.00 NO $1,369

F-16
EP 1110-1-8, Vol. 2
30EP 1110-1-8
Apr 14
(Vol. 8)
4/30/2014
APPENDIX F
TUBE COST
IPPO94 26x7x20 7.00 x 26.00 NO $1,712

CPPO1 10x8x3 8.00 x 10.00 NO $68
IPPO36 15x8x11-1/4 8.00 x 15.00 NO $915
IPPO61 18x8x12-1/8 8.00 x 18.00 NO $1,070
IPPO66 18x8x14 8.00 x 18.00 NO $1,115
IPPO71 20x8x16 8.00 x 20.00 NO $1,195
IPPO76 21x8x15 8.00 x 21.00 NO $1,415
IPPO82 22x8x16 8.00 x 22.00 NO $1,477
IPPO37 15x9x11-1/4 9.00 x 15.00 NO $1,218
IPPO67 18x9x14 9.00 x 18.00 NO $1,177
IPPO62 18x9x12-1/8 9.00 x 18.00 NO $1,265
IPPO72 20x9x16 9.00 x 20.00 NO $1,622
IPPO77 21x9x15 9.00 x 21.00 NO $1,692
IPPO83 22x9x16 9.00 x 22.00 NO $1,678
IPPO16 22x9x16 9.00 x 22.00 NO $1,678
IPPO92 22x10x17-3/4 10.00 x 22.00 NO $2,030
IPPO84 22x10x16 10.00 x 22.00 NO $2,270
IPPO95 28x10x22 10.00 x 28.00 NO $2,727
IPPO78 21x12x15 12.00 x 21.00 NO $2,720
IPPO86 22x12x16 12.00 x 22.00 NO $2,394
IPPO96 28x12x22 12.00 x 28.00 NO $3,547
IPPO87 22x14x16 14.00 x 22.00 NO $2,666
IPPO93 22x14x17-3/4 14.00 x 22.00 NO $3,083
IPPO88 22x16x16 16.00 x 22.00 NO $2,939
IPPO98 28x16x22 16.00 x 28.00 NO $5,050
CONVEYOR/LOADER BELTING
CONVEYOR BELTING (GOODYEAR EP) (Life = 5000 hrs )
AZZA1 Conveyor Belting 24.00 x 50.00 2 NO $1,185


F-17
EP 1110-1-8, Vol. 2
EP 1110-1-8
30
Apr 14
(Vol. 8)
4/30/2014
APPENDIX F
TUBE COST


F-18
EP 1110-1-8, Vol. 2
30 AprEP14
1110-1-8
(Vol. 8)
4/30/2014
APPENDIX F
TUBE COST

(1) TT = includes tube, TL = no tube, NO = no tube F -

19
F-19
EP 1110-1-8, Vol. 2
30 Apr 14
F-20
EP 1110-1-8, Vol. 2
30 Apr 14
APPENDIX G
TIRE LIFE AND TIRE WEAR FACTORS
SECTION I. TIRE WEAR FACTORS
The tire wear factors used in this pamphlet are listed in appendix D. The “useful life” of
a new tire is the product of Condition Factors (CF) from I through V, the Wheel Position
Factor (WPF), the Grade Factor (GF) (for Drive Tires only) and the Miscellaneous
Condition (MC). These factors provide a percentage reduction to the maximum tire life.
See chapter 2 for tire cost methodology.
Condition Factors, Wheel Position Factors, Grade Factor, and Miscellaneous Condition
are derived from the Caterpillar Performance Handbook.
The factors shown below are examples specifically for a rear dump wagon.
Condition Factors (CF): Average Severe

I. Maintenance 0.981 0.763
II. Speed 0.872 0.763
III. Curves 0.981 0.872
IV. Surface Condition 0.981 0.763
V. Loads 1.090 0.709
CF Product of the factors 0.897 0.275

(I x II x III x IV x V)
VI. Wheel Position Factors (WPF):

WPF-FT Front Tire (FT) 0.981 0.981
WPF-DTR Drive Tire (DT) - Rear Dump 0.818 0.709
WPF-TT Trailing Tire (TT) 1.090 1.090
VII. Grade Factor (GF) (Drive Tires Only) 0.981 0.763
VIII. Miscellaneous Condition (MC) 1.090 0.981
G-1
EP 1110-1-8, Vol. 2
30 Apr 14
SECTION I. TIRE WEAR FACTORS (Continued)
Example: Final Tire Wear Factors for Wagon, Rear Dump

(See Appendix D, Category W15)
Average Severe
Front Tire - Average =

(CF = 0.897)(WPF-FT = 0.981)(MC = 1.090) 0.96
Front Tire - Severe =
(CF = 0.275)(WPF-FT = 0.981)(MC = 0.927) 0.60
Drive Tire - Average =
(CF = 0.897)(WPF-DTR = 0.763)(GF = 0.981)(MC = 1.090) 0.78
Drive Tire - Severe =
(CF = 0.275)(WPF-DTR = 0.732)(GF = 0.763)(MC = 0.927) 0.15
Trailing Tire - Average =
(CF = 0.897)(WPF-TT = 1.090)(MC = 1.090) 1.07
Trailing Tire - Severe =
(CF = 0.275)(WPF-TT = 1.090)(MC = 0.927) 0.29
SECTION II. MAXIMUM TIRE LIFE
Maximum tire life is used in the formula to determine tire wear cost and is located in
Appendix F by type of tire.
G-2
EP 1110-1-8, Vol.
EP 21110-1-8
30 Apr 14 (Vol. 8)
4/30/2014
APPENDIX H
MANUFACTURER LIST
CODE MANUFACTURER
A1 - ALLIED-GATOR, INC.
A2 - ASV INC.
A3 - AMERICAN PILEDRIVING EQUIPMENT, INC.
A4 - ATLAS COPCO WAGNER INC.
AA - AMERICAN AUGERS, INC.
AB - ALLMAND BROTHERS INC.
AC - ACE ENTERPRISES
AD - ACKER DRILL COMPANY INC.
AE - AEROIL PRODUCTS COMPANY, INC.
AF - AIRPLACO EQUIPMENT CO., INC.
AG - ARROW-MASTER, INC.
AH - AUTO CRANE CO.
AI - AMIDA INDUSTRIES, INC.
AJ - ALLEN ENGINEERING CORP.
AK - TYLER EQUIPMENT CO.
AL - ALLENTOWN EQUIPMENT
AM - AMERICAN CRANE CORPORATION (TEREX)
AN - ATLANTIC
AO - ALKOTA CLEANING SYSTEMS, INC.
AP - PECCO AND WOLFF TOWER CRANES (MORROW)
AQ - AQUATICS UNLIMITED
AR - AMERICAN ROAD MACHINERY, INC.
AS - ATLAS COPCO CONSTRUCTION TOOLS INC.
AT - ANDERSON MAVOR INC.
AU - ALLIED CONSTRUCTION PRODUCTS
AV - ALIVA LTD.
AW - AIRMAN (HOKUETSU INDUSTRIES CO. LTD.)
AX - AMERICAN COMPACTION EQUIPMENT, INC.
H-1
H-1
EP 1110-1-8,
EP 1110-1-8 Vol. 2
30 Apr 14
(Vol. 8)
4/30/2014
APPENDIX H
MANUFACTURER LIST
CODE MANUFACTURER
AY - KOMLINE-SANDERSON ENGINEERING CO.
AZ - ALLIS-CHALMERS CORP.
BA - BADGER EQUIPMENT CO.
BB - BASCO
BC - NORTH STAR ENGINEERED PRODUCTS, INC.
BD - BRODERSON MANUFACTURING CORPORATION
BE - INGERSOLL RAND MATERIAL HANDLING
BF - BENFORD
BG - BARBER-GREENE COMPANY
BI - BOR-IT MANUFACTURING COMPANY INC.
BJ - BURKEEN MANUFACTURING CO.
BK - BLAW KNOX CONSTRUCTION EQUIPMENT CORP.
BL - US FILTER/BLASTRAC
BM - BROCE MANUFACTURING COMPANY
BN - BANDIT INDUSTRIES, INC.
BO - COMPACTION AMERICA (BOMAG)
BQ - BELL EQUIPMENT NORTH AMERICA INC .
BR - BROOKVILLE MINING EQUIPMENT CORP.
BS - BALDERSON, INC.
BT - BREAKER TECHNOLOGY INC.
BU - BUSH HOG
BW - BOWIE INDUSTRIES, INC.
BX - BIL-JAX, INC.
BY - BUCYRUS INTERNATIONAL INC.
C1 - COYOTE LOADER SALES, INC.
C2 - CARELIFT EQUIPMENT
C3 - TIME CONDOR CORPORATION
C4 - CATERPILLAR LIFT TRUCKS,
H-2
H-2
EP 1110-1-8, Vol.
EP 21110-1-8
30 Apr 14 (Vol. 8)
4/30/2014
APPENDIX H
MANUFACTURER LIST
CODE MANUFACTURER
C5 - Construction Equipment Company
CA - CATERPILLAR INC. ( MACHINE DIVISION)
CB - CONSOLIDATED BALING MACHINE COMPANY, INC
CC - CEMEN TECH
CD - CDS GROUP
CE - ATHEY PRODUCTS CORPORATION
CF - CGR COMPACTING
CG - CHEMGROUT, INC.
CH - CHAMPION ROAD MACHINERY-PRO PAV (WIRTGEN
CI - CHIPMORE MANUFACTURING CO., INC.
CJ - COLD JET
CK - CHICAGO PNEUMATIC TOOL CO.
CL - CON-E-CO
CM - CLEMCO INDUSTRIES CORPORATION
CN - CEMEN TECH, INC.
CO - WASTE CONTROL SYSTEMS, INC.
CP - CRISAFULLI PUMP
CQ - CUSHION CUT, INC. (HUSQVARNA)
CR - CAMLEVER
CS - CASE CORPORATION
CT - CLEVELAND PACIFIC TRENCHER CO
CU - WASTEQUIP CUSCO INDUSTRIES
CV - CONMACO, INC.
CW - TEREX - CMI (TEREX ROADBUILDING)
CX - CMC (CONSTRUCTION MACHINERY COMPANY)
CY - CENTRIC
CZ - CLYDE IRON WORKS
DA - ELCO INTERNATIONAL INC.
H-3
H-3
EP 1110-1-8,
EP 1110-1-8 Vol. 2
30 Apr 14
(Vol. 8)
4/30/2014
APPENDIX H
MANUFACTURER LIST
CODE MANUFACTURER
DD - DELTA DREDGE & PUMP CORP.
DE - DEMOLITION TECHNOLOGIES
DF - DURA FLOAT
DG - DAINONG HEAVY INDUSTRIES, INC.
DH - DAEWOO HEAVY INDUSTRIES LTD.
DI - DICKSON INDUSTRIES INC.
DJ - CATERPILLAR/DJB
DL - PILECO, INC.
DN - Dynatech
DO - DOSCO CORPORATION
DP - DOOSAN PORTABLE POWER
DR - DRESSER MINING EQUIPMENT
DS - DREDGING SUPPLY COMPANY (DSC)
DT - DRILTECH, INC. (SANDVIK)
DW - DITCH WITCH (THE CHARLES MACHINE WORKS)
DY - DYNAPAC DIVISION - SVEDALA INDUSTRIES
EA - EAGER BEAVER
EC - ELGIN SWEEPER COMPANY
ED - EQUIPMENT DEVELOPMENT CO., INC. (EDCO)
EI - EIMCO JARVIS CLARK
EJ - CEDARAPIDS INC., A TEREX COMPANY
EL - ELLICOTT MACHINE CORPORATION
EM - EXCEL MACHINERY LTD.
EP - ENVIRO-PAK
ES - ESCO CORPORATION
ET - E. D. ETNYRE & CO.
EU - EUCLID INDUSTRIES, INC.
EX - EXCEL INDUSTRIES, INC.
H-4
H-4
EP 1110-1-8, Vol.
EP 21110-1-8
30 Apr 14 (Vol. 8)
4/30/2014
APPENDIX H
MANUFACTURER LIST
CODE MANUFACTURER
EZ - E-Z DRILL, INC.
FC - FERMEC NORTH AMERICA LTD., A TEREX CO.
FE - FELKER (TARGET)
FG - FINN CORPORATION
FH - FRUEHAUF TRAILER CORPORATION
FI - FIATALLIS
FK - FRANKLIN TREEFARMER
FL - FLETCHER MINING EQUIPMENT
FN - NEW HOLLAND NORTH AMERICA, INC.
FO - FORD MOTOR COMPANY
FR - FERGUSON MANUFACTURING & EQUIPMENT
FS - FIVE STAR MANUFACTURING CO/ELGIN SWEEPER
FU - FURUKAWA CO.,LTD.
G1 - GRACO, INC.
GA - GRADALL COMPANY
GB - GAR-BRO MANUFACTURING COMPANY
GC - GEHL COMPANY
GD - GARDNER-DENVER INDUSTRIAL MACHINES
GE - GENSCO AMERICA CO. LTD.
GF - GRIFFIN DEWATERING CORP.
GH - GEITH INC.
GI - GALION DIVISION
GJ - GENIE INDUSTRIES
GL - GARLOCK EQUIPMENT CO.
GM - GMC AND CHEVROLET
GN - GALION DUMP BODIES, INC.
GO - GOMACO CORPORATION
GR - GORMAN-RUPP COMPANY
H-5
H-5
EP 1110-1-8,
EP 1110-1-8 Vol. 2
30 Apr 14
(Vol. 8)
4/30/2014
APPENDIX H
MANUFACTURER LIST
CODE MANUFACTURER
GT - GILCREST EQUIPMENT COMPANY
GV - GROVE CRANES (MANITOWOC)
GW - GROVE MANLIFT (JLG)
HA - HAZCO SERVICES, INC.
HB - HAWCO (ANVIL ATTACHMENTS)
HC - HAMM COMPACTORS, INC.
HD - HYDRAULIC POWER SYSTEMS, INC.
HE - HENDRIX MANUFACTURING COMPANY, INC.
HF - HYDRA-MAC INTERNATIONAL, INC.
HG - HUSQVARNA CONSTRUCTION PRODUCTS
HH - ESG MANUFACTURING H&H PUMP & DREDGE
HI - HITACHI CONSTRUCTION MACHINERY
HM - H&M VIBRO, INC.
HN - HINO DIESEL TRUCKS (U.S.A.) INC.
HO - RIVERSIDE PUMP MANUFACTURING
HP - COMPACTION AMERICA
HQ - HYPAC COMPACTION EQUIPMENT
HR - HYDROCAL INC.
HU - HYUNDAI CONSTRUCTION EQUIPMENT
HV - HUSQVARNA FOREST & GARDEN CO.
HW - HEWITT-ROBINS
HY - HYSTER CO.
HZ - HOFFCO-COMET
IA - INGERSOLL RAND ROTARY-REC COMPRESSOR DIV
IB - INGERSOLL RAND DRILLING (ATLAS COPCO)
IC - INTERNATIONAL CONSTRUCTION EQUIPMENT,INC
ID - KOMATSU DRESSER
IE - IDEAL MANUFACTURING, INC.
H-6
H-6
EP 1110-1-8, Vol.
EP 21110-1-8
30 Apr 14 (Vol. 8)
4/30/2014
APPENDIX H
MANUFACTURER LIST
CODE MANUFACTURER
IF - INGERSOLL RAND PORTABLE COMPRESSOR DIV
IG - INGRAM COMPACTING, LLC
IH - NAVISTAR INTERNATIONAL TRANSPORTATION
IM - INNOVATIVE MATERIAL SYSTEMS, INC. (IMS)
IN - INGERSOLL RAND CO.
IP - INGERSOLL RAND ROAD MACHINERY DIV
IR - INGERSOLL RAND ROCK DRILL DIV
IS - INSLEY DIVISION
IT - NAVISTAR INTERNATIONAL CORPORATION
JC - JCB INC.
JD - DEERE & COMPANY
JE - JCL EQUIPMENT CO.
JL - JLG INDUSTRIES, INC.
JM - JEFFREY MINING MACHINERY DIVISION
JO - C. S. JOHNSON COMPANY
JR - JRB COMPANY INC.
JS - JOHNSTON SWEEPER COMPANY
JU - ATI-Bell
KA - KAWASAKI LOADERS, INC.
KB - KOLBERG - PIONEER, INC
KC - KOBELCO AMERICA INC.
KD - K-D MANITOU, INC.
KE - KENWORTH TRUCK COMPANY
KF - KNAPHEIDE MANUFACTURING CO.
KH - KOHLER COMPANY
KI - KLEIN PRODUCTS, INC.
KK - KEENE ENGINEERING INC.
KL - KOLMAN / ATHEY DIV.
H-7
H-7
EP 1110-1-8,
EP 1110-1-8 Vol. 2
30 Apr 14
(Vol. 8)
4/30/2014
APPENDIX H
MANUFACTURER LIST
CODE MANUFACTURER
KM - Komatsu America International Company
KN - KENT DEMOLITION TOOLS
KO - KOEHRING CRANES, INC.
KP - KOCH-WATER
KR - KORI CORPORATION
KU - KUBOTA TRACTOR CORPORATION
KW - KERSHAW MFG., CO.
KZ - KEIZER TECHNOLOGIES AMERICAS, INC
LA - LAYTON MANUFACTURING COMPANY
LB - LINK-BELT CONSTRUCTION EQUIPMENT CO.
LC - LINCOLN ELECTRIC COMPANY
LD - LEE-BOY
LE - LELY PACIFIC, INC.
LF - LOFTNESS / US ATTACHMENTS
LG - LITTLE GIANT CRANE & SHOVEL INC.
LH - MORROW EQUIPMENT COMPANY, LLC
LI - LINK-BELT CONSTRUCTION EQUIPMENT COMPANY
LK - LIFTKING INDUSTRIES, INC.
LL - OMNIQUIP, LULL
LN - LONDON MACHINERY INC.
LO - LORAIN CRANES DIVISION
LS - LAKE SHORE MINING EQUIPMENT INC.
LU - LABOUNTY MANUFACTURING,
LY - BOART LONGYEAR COMPANY
LZ - LIEBHERR CONSTRUCTION EQUIPMENT CO.
M1 - MANITEX - MANITOWOC BOOM TRUCKS GROUP
M2 - MAULDIN - CALDER BROTHERS CORP.
M3 - MAYCO PUMP - MULTIQUIP INC.
H-8
H-8
EP 1110-1-8, Vol.
EP 21110-1-8
30 Apr 14 (Vol. 8)
4/30/2014
APPENDIX H
MANUFACTURER LIST
CODE MANUFACTURER
M4 - MITCHELL INDUSTRIAL TIRE COMPANY (MITCO)
MA - MANITOWOC ENGINEERING CO.
MB - M-B COMPANIES, INC.
MC - VME NORTH AMERICA
MD - MDI/YUTANI
ME - MELROE COMPANY/BOBCAT
MF - MF INDUSTRIAL
MG - McMASTER-CARR
MH - MITSUBISHI FUSO TRUCK OF AMERICA
MI - MITSUBISHI CONSTRUCTION EQUIP.
MJ - MILLER SPREADER CO.
MK - MKT MANUFACTURING, INC.
ML - ITT MARLOW PUMPS
MM - MACO-MUEDON
MN - GRANUTE-SATURN SYSTEMS(MAC CORPORATION)
MO - MORGEN MANUFACTURING CO.
MP - MIDLAND MACHINERY CO
MQ - MORBARK, INC.
MR - FOREMOST MOBILE DRILLING COMPANY, INC.
MS - MUSTANG UNITS COMPANY
MT - MACK TRUCKS, INC.
MU - MULTIQUIP, INC.
MV - MAYVILLE ENGINEERING CO., INC.
MW - M-B-W, INC.
MX - MAXON INDUSTRIES
MY - MIDLAND MANUFACTURING INC.
MZ - MARINE INLAND FABRICATORS
NA - NAGANO - LELY CORP.
H-9
H-9
EP 1110-1-8,
EP 1110-1-8 Vol. 2
30 Apr 14
(Vol. 8)
4/30/2014
APPENDIX H
MANUFACTURER LIST
CODE MANUFACTURER
NB - NASCO EQUIPMENT CO. INC.
NC - NATIONAL CRANE CORPORATION
NE - NEAL MANUFACTURING COMPANY, INC
NI - NIFTYLIFT INC. - USA
NL - NLB CORPORATION
NO - NORTHWEST ENGINEERING COMPANY
NP - NPK CONSTRUCTION EQUIPMENT
OE - OLIN ENGINEERING, INC.
OK - O & K ORENSTEIN & KOPPEL INC.
OL - OLYMPYK CHAIN SAWS
ON - ONAN CORPORATION
PA - PALFINGER INC.
PB - PETTIBONE MICHIGAN LLC
PC - GETMAN BROTHERS MFG. COMPANY
PE - PETERBILT MOTORS COMPANY
PH - P & H
PI - PIQUA ENGINEERING
PL - PRO-LINE / ANVIL ATTACHMENTS
PN - PEMBERTON, INC.
PO - PROGRESSIVE DEVELOPMENT INC.
PP - PACIFIC RUBBER
PR - USFILTER PERRIN PRODUCTS
PS - POWER CURBERS, INC.
PT - PATENT CONSTRUCTION SYSTEMS
PU - PUTZMEISTER INC.
PW - POWERSCREEN INTERNATIONAL DISTRIBUTN LTD
RA - METSO MINERALS
RC - JOHNSON-ROSS (TEREX ROADBUILDING)
H-10
H-10
EP 1110-1-8, Vol.
EP 21110-1-8
30 Apr 14 (Vol. 8)
4/30/2014
APPENDIX H
MANUFACTURER LIST
CODE MANUFACTURER
RD - REEDRILL (TEREX)
RE - NORSTAR PRODUCTS INTERNATIONAL, INC.
RI - REYNOLDS INTERNATIONAL, L.P.
RK - RAPID MIX
RL - REICHDRILL
RM - ROME PLOW CO.
RN - ALLIED SYSTEMS COMPANY (RANGER)
RO - ROBBINS COMPANY
RQ - REED MANUFACTURING
RR - RAMMER - GR COSTRUTTORI - SANDVIK
RS - ROSCO, A LeeBoy COMPANY
RT - ROADTEC ( ASTEC INDUSTRIES COMPANY)
RX - RAMMAX MACHINERY CO.
S1 - STANLEY HYDRAULIC TOOLS
S2 - SCHRAMM, INC
S3 - CHAMPION ROAD MACHINERY - SUPERPAC CO.
S4 - SUPERIOR INDUSTRIES, AN ASTEC COMPANY
S5 - SOMAT WASTE REDUCTION TECHNOLOGY
S6 - SUPERIOR TIRE & RUBBER CORP.
SA - SAUERMAN (NATIONAL OILWELL VARCO)
SB - SCAT TRAK - OMNIQUIP - TEXTRON INC.
SC - SCHWING AMERICA INC.
SD - SIOUX STEAM CLEANER CORPORATION
SE - SEALMASTER, INC.
SF - SECO CORPORATION
SG - STONE CONSTRUCTION EQUIPMENT, INC.
SH - SHRED-TECH LIMITED
SI - SAKAI AMERICA, INC.
H-11
H-11
EP 1110-1-8,
EP 1110-1-8 Vol. 2
30 Apr 14
(Vol. 8)
4/30/2014
APPENDIX H
MANUFACTURER LIST
CODE MANUFACTURER
SJ - SKYJACK, INC.
SK - LTV ENERGY PRODUCTS (SKAGIT)
SL - SHUTTLELIFT, INC.
SM - SEAARK MARINE
SN - STEPHENS MANUFACTURING CO., INC.
SO - SOUTHWEST CONSTRUCTION EQUIPMENT CO.
SP - SPRAGUE AND HENWOOD
SQ - SCHAEFF INC.
SR - SULLAIR CORPORATION
SS - SAMSUNG CONSTRUCTION EQUIPMENT AMERICA
ST - STOW MANUFACTURING, INC.
SU - SULLIVAN-PALATEK, INC.
SV - SOMERO ENTERPRISES, INC.
SW - SNORKEL
SX - SELLICK EQUIPMENT LIMITED
SY - SKY TRAK - OMNIQUIP - TEXTRON INC.
SZ - STRATO-LIFT INTERNATIONAL CORP.
TA - TAMPO MANUFACTURING CO., INC.
TB - TERRAMITE CONSTRUCTION EQUIPMENT
TC - TCM
TD - TADANO AMERICA CORPORATION
TE - TEREX CORPORATION
TF - THOMAS EQUIPMENT LTD.
TG - TIMBCO HYDRAULICS, INC.
TH - TEEMARK CORPORATION
TI - TIMBERJACK, A JOHN DEERE COMPANY
TJ - TRAMAC
TK - TAKEUCHI MFG. (U.S.), LTD
H-12
H-12
EP 1110-1-8, Vol.
EP 21110-1-8
30 Apr 14 (Vol. 8)
4/30/2014
APPENDIX H
MANUFACTURER LIST
CODE MANUFACTURER
TL - BREAKER TECHNOLOGY, INC. (AN ASTEC CO.)
TM - TESMEC USA, INC.
TO - TORO
TR - TEREX MINING
TS - TELSMITH INC.
TT - TRAIL KING INDUSTRIES, INC.
TU - TITAN INTERNATIONAL, INC.
TV - TRAVERSE LIFT CO.
UE - UNDERGROUND EQUIPMENT & SUPPLY
UL - UNIVERSAL ENGINEERING - SVEDALA - METSO
UN - UNIT RIG
UP - UPRIGHT INC.
VA - VOEST-ALPINE
VB - VIBROMAX AMERICA INC.
VE - VERMEER MANUFACTURING CO.
VI - VINCE HAGAN COMPANY
VO - VOLVO CONSTRUCTION EQUIPMENT GROUP
VP - VOGELE AMERICA - PRO-PAV DIV.
VS - VALLEY SLURRY SEAL / MACROPAVER DIVISION
VT - VALMET - PARTEK FOREST LLC
VU - VULCAN FOUNDATION EQUIPMENT, INC
WA - HAULPAK DIVISION
WB - WEBER MASCHINENTECHNIK GMBH
WC - WACKER CORPORATION
WD - WALDON, INC.
WE - WEATHERFORD U.S. INC.
WF - WATSON INC.
WG - ATLAS COPCO WAGNER
H-13
H-13
EP 1110-1-8,
EP 1110-1-8 Vol. 2
30 Apr 14
(Vol. 8)
4/30/2014
APPENDIX H
MANUFACTURER LIST
CODE MANUFACTURER
WH - WIGGINS LIFT CO., INC.
WI - WILLMAR EQUIPMENT COMPANY
WL - WALKER MANUFACTURING CO., INC.
WN - WAIN-ROY, INC.
WO - WACO SCAFFOLDING & EQUIPMENT
WR - WARNER FRUEHAUF TRAILER CO., INC.
WS - WHITEMAN CONSPRAY, INC.
WT - WIRTGEN AMERICAN, INC.
XX - NO SPECIFIC MANUFACTURER
YA - YANMAR DIESEL AMERICA CORP
YB - ADVANCED ENVIRONMENTAL SOLUTIONS
ZZ - GENERIC EQUIPMENT
H-14
H-14
EP 1110-1-8, Vol. 2
EP 1110-1-8
(Vol. 8) 14
30 Apr
4/30/2014
APPENDIX I
FEDERAL COST-OF-MONEY RATE
(Renegotiation or Prompt Payment Rate)
EFFECTIVE MONTHS EFFECTIVE DATE RATE
JANUARY - JUNE 1/1/1999 5.000%
JULY - DECEMBER 7/1/1999 6.500%
JANUARY - JUNE 1/1/2000 6.750%
JULY - DECEMBER 7/1/2000 7.250%
JANUARY - JUNE 1/1/2001 6.375%
JULY - DECEMBER 7/1/2001 5.875%
JANUARY - JUNE 1/1/2002 5.500%
JULY - DECEMBER 7/1/2002 5.250%
JANUARY - JUNE 1/1/2003 4.250%
JULY - DECEMBER 7/1/2003 3.125%
JANUARY - JUNE 1/1/2004 4.000%
JULY - DECEMBER 7/1/2004 4.500%
JANUARY - JUNE 1/1/2005 4.250%
JULY - DECEMBER 7/1/2005 4.500%
JANUARY - JUNE 1/1/2006 5.125%
JULY - DECEMBER 7/1/2006 5.750%
JANUARY - JUNE 1/1/2007 5.250%
JULY - DECEMBER 7/1/2007 5.750%
JANUARY - JUNE 1/1/2008 4.750%
JULY - DECEMBER 7/1/2008 5.125%
JANUARY - JUNE 1/1/2009 5.625%
JULY - DECEMBER 7/1/2009 4.875%
JANUARY - JUNE 1/1/2010 3.250%
JULY - DECEMBER 7/1/2010 3.125%
JANUARY - JUNE 1/1/2011 2.625%
JULY - DECEMBER 7/1/2011 2.500%
JANUARY - JUNE 1/1/2012 2.000%
JULY - DECEMBER 7/1/2012 1.750%
JANUARY - JUNE 1/1/2013 1.375%
JULY - DECEMBER 7/1/2013 1.750%
JANUARY - JUNE 1/1/2014 2.125%
I-1
I-1
EP 1110-1-8, Vol. 2
30 Apr 14
I-2
EP 1110-1-8, Vol. 2
30 Apr 14
APPENDIX J
EQUIPMENT ACCESSORIES
The following accessories are listed by category (CAT), subcategory (SUB), and
description (including features required for safety). The accessories have been
included with the major equipment listed in this pamphlet when they are not included
with the basic cost and are offered by the manufacturer.
CAT SUB DESCRIPTION

C85.10 CRANES, DRAGLINE AND CLAMSHELL, CRAWLER MOUNTED
Power load lowering
Independent swing and travel
Third drum
Torque converter [machines 1 1/2 cubic yard (cy) or larger]
Approximately one-half maximum boom length
Counterweight (standard)
Fire extinguisher 5-B:C
Swing and reverse signal (backup) alarm
Boom angle indicator and a load-indicating device
Drum rotation indicators
Anti-two block (upper limit) devices
Manufacturers’ mandatory accessories
C85.20 CRANES, LIFTING, CRAWLER MOUNTED

Power load lowering
Independent swing and travel
Third drum
Torque converter (machines 25 tons or larger)
One-half maximum boom length (machines less than 60 tons)
Maximum boom length at 360 degree rating (machines larger than
60 tons)
Manufacturers’ mandatory accessories
Hook block on machines larger than 100 tons
C90.01 TRUCK CRANES - LESS THAN 25 TONS
J-1
EP 1110-1-8, Vol. 2
30 Apr 14
CAT SUB DESCRIPTION

Power load lowering
Third drum
Mechanical outriggers with screw jacks
Maximum boom length at 360 degrees rating
Manufacturers mandatory accessories
C90.02 TRUCK CRANE - 25 TONS AND LARGER

C90.03 Power load lowering
C90.04 Third drum
Hydraulic outriggers with screw jacks
Torque converter when available (upper only)
Maximum boom length at 360 degrees rating
Reverse signal (backup) alarm
Hook block on machines larger than 100 tons
G15 GRADER
Rollover protective structures (ROPS) with enclosed cab
Ripper/scarifier, rear mounted
Front wheel lean
Power circle
Hydraulic shift and tilt moldboard
End bits
Standard work lights
H25 EXCAVATORS, HYDRAULIC

H30 Backhoe bucket (standard)
Backhoe stick (medium length)
Backhoe boom (one piece)
J-2
EP 1110-1-8, Vol. 2
30 Apr 14
CAT SUB DESCRIPTION

Backhoe bucket linkage (with cylinder)
Guards
Counterweight
ROPS
H35 HYDRAULIC SHOVELS - CRAWLER MOUNTED

Torque converter (machines 1 1/2 cy or larger)
Counterweight
ROPS
L30 LOADERS, BELT (CONVEYOR BELTS)

Power unit
Head pulley clutch and backstop
Belt cleaner and belt installing equipment
King pin attachments
L35 LOADERS, 1 1/2 cy AND LARGER

L40 Blower fan
Guard, power train
Automatic bucket positioner
Standard counterweight
Machines less than 7 cy: General purpose or excavating bucket
with bolt on cutting edge and no teeth
Machines 7 cy or larger: Rock bucket with bolt on cutting edge and
teeth
ROPS
S10 SCRAPERS
S15 Control single lever
S20 Blower fan
Standard work light
Guards, power train
J-3
EP 1110-1-8, Vol. 2
30 Apr 14
CAT SUB DESCRIPTION

ROPS
Supplemental steering
T15 TRACTOR, CRAWLER

Hydraulic controls for ripper and blade
Guards
Blower fan
Hook, front pull
Track grousers (severe service for units over 200 hp)
Counterweights where required
ROPS
Universal blade
T20 TRACTOR, WHEEL

Hydraulic controls for ripper and blade
Guards
Blower fan
Blade
Counterweights when required
T25 TRACTOR, AGRICULTURAL

Independent power take off (PTO)
Counterweights when required
3-point hitch
ROPS
Hydraulic system with controls
T55 TRUCKS, OFF-HIGHWAY

No spin differential
Tachograph
Engine and transmission guards
Body liners
J-4
EP 1110-1-8
(Vol. 1)
4/30/2014
EP 1110-1-8, Vol. 2
APPENDIX K 30 Apr 14
Ground Engaging Component Costs Included in Repairs (RCF)
Blade cutting Bucket teeth,
CATEGORY edges, wear plates, cutting edges, Ripper tips and Equipment
hard facing, and side cutters, and shank protection Specific Wear
end plates wear plates Items
SUB DESCRIPTION EK C DC LIFE SLV RCF
B15 0.00 BROOMS, STREET SWEEPERS & FLUSHERS 95 A B 8,000 0.10 0.80
B25 0.00 BUCKETS, CLAMSHELL 15 A B 8,000 0.10 0.70
B25 0.00 BUCKETS, CLAMSHELL 15 S B 6,500 0.10 0.80
B35 0.00 BUCKETS, DRAGLINE 1
B35 0.10 LIGHT WEIGHT 15 A B 8,000 0.10 0.70
B35 0.10 LIGHT WEIGHT 15 S B 6,500 0.10 0.80
B35 0.20 MEDIUM WEIGHT 15 A B 9,000 0.10 0.70
B35 0.20 MEDIUM WEIGHT 15 S B 7,000 0.10 0.80
B35 0.30 HEAVY WEIGHT 15 A B 10,000 0.10 0.70
B35 0.30 HEAVY WEIGHT 15 S B 8,000 0.10 0.80
G15 0.00 GRADERS, MOTOR 35 A B 14,500 0.25 0.75
G15 0.00 GRADERS, MOTOR 35 S B 13,500 0.25 0.85
H25 0.00 HYDRAULIC EXCAVATORS, CRAWLER MOUNTED 1
H25 0.10 0 LBS THRU 12,500 LBS (COMPACT EXCAVATORS) 65 A B 8,000 0.25 0.70
H25 0.10 0 LBS THRU 12,500 LBS (COMPACT EXCAVATORS) 65 S B 7,000 0.25 0.80
H25 0.11 OVER 12,500 LBS THRU 40,000 LBS 65 A B 8,500 0.25 0.70
H25 0.11 OVER 12,500 LBS THRU 40,000 LBS 65 S B 7,000 0.25 0.85
EK=Economic Key (Appendix E) C=Operating Conditions (A=average, S=severe) DC=Discount Code (B=basic 7.5%, S=special 15%)
LIFE=Economic Life SLV=Salvage Value RCF=Repair Cost Factor
Ground Engaging Component (GEC) is defined as those wear items on the machine that come in direct contact with in situ ground to perform the machines primary function.
For machines with blades, GEC can include: cutting edges, wear plates, hard facing, and end plates. For machines with buckets, GEC can include: bucket teeth, cutting edges,
side cutters, and wear plates. For machines with rippers, GEC can include: tips and shank protectors. Equipment Specific Wear items include those items of wear that are
specific to that equipment. Not included in the Repairs and must be added as needed are: drill/bits, drill/steel, roadheader/rock breaking bits, air tools/breaker
points/jackhammer points, concrete coring drill bits, and other wear items that are notL-
shown
1 here.
K-1
EP 1110-1-8
(Vol. 1)
4/30/2014
EP 1110-1-8, Vol. 2
30 Apr 14 APPENDIX K
H25 0.14 OVER 160,000 LBS 65 A B 19,000 0.25 1.10
H25 0.14 OVER 160,000 LBS 65 S B 15,000 0.25 1.25
H30 0.00 HYDRAULIC EXCAVATORS, WHEEL MOUNTED 1
H30 0.01 0 THRU 1.0 CY 65 A B 8,000 0.25 0.50
H30 0.01 0 THRU 1.0 CY 65 S B 6,500 0.25 0.55
H30 0.02 OVER 1.0 CY 65 A B 10,000 0.25 0.60
H30 0.02 OVER 1.0 CY 65 S B 8,000 0.25 0.65
H35 0.00 HYDRAULIC SHOVELS, CRAWLER MOUNTED 1
H35 0.11 DIESEL, 0 CY THRU 5.0 CY 65 A B 14,000 0.20 1.00
H35 0.11 DIESEL, 0 CY THRU 5.0 CY 65 S B 12,000 0.20 1.10
H35 0.12 DIESEL, OVER 5.0 CY 65 A B 16,000 0.20 1.20
H35 0.12 DIESEL, OVER 5.0 CY 65 S B 14,000 0.20 1.30
H35 0.21 ELECTRIC, OVER 2.5 CY 65 A B 18,000 0.20 0.80
H35 0.21 ELECTRIC, OVER 2.5 CY 65 S B 16,000 0.20 0.90
L35 0.00 LOADERS, FRONT END, CRAWLER TYPE 40 A B 10,000 0.20 1.10
L35 0.00 LOADERS, FRONT END, CRAWLER TYPE 40 S B 8,000 0.20 1.25
L40 0.00 LOADERS, FRONT END, WHEEL TYPE 1
L40 0.11 ARTICULATED, 0 THRU 225 HP 45 A B 9,250 0.25 0.70
L40 0.11 ARTICULATED, 0 THRU 225 HP 45 S B 8,750 0.25 0.80
shown
2 here.
K-2
EP 1110-1-8
(Vol. 1)
EP 1110-1-8, 4/30/2014
Vol. 2
APPENDIX K 30 Apr 14
L40 0.12 ARTICULATED, OVER 225 HP 45 A B 13,500 0.20 0.70

L40 0.12 ARTICULATED, OVER 225 HP 45 S B 12,000 0.20 0.75
L40 0.20 SKID STEER 45 A B 8,000 0.20 0.80
L40 0.31 TOOL CARRIER & TELESCOPIC HANDLERS, 0 THRU 225 HP 45 A B 10,000 0.25 0.85
L40 0.31 TOOL CARRIER & TELESCOPIC HANDLERS, 0 THRU 225 HP 45 S B 9,250 0.25 0.90
L40 0.32 TOOL CARRIER & TELESCOPIC HANDLERS, OVER 225 HP 45 A B 12,000 0.15 0.85
L40 0.32 TOOL CARRIER & TELESCOPIC HANDLERS, OVER 225 HP 45 S B 10,000 0.15 0.90
L45 0.00 LOADERS / BACKHOE, CRAWLER TYPE 40 A B 8,000 0.20 1.35
L45 0.00 LOADERS / BACKHOE, CRAWLER TYPE 40 S B 6,000 0.20 1.40
L50 0.00 LOADERS / BACKHOE, WHEEL TYPE 45 A B 10,000 0.25 0.80
L50 0.00 LOADERS / BACKHOE, WHEEL TYPE 45 S B 6,000 0.25 0.85
L60 0.00 LOG SKIDDERS 75 A B 10,000 0.15 0.70
L60 0.00 LOG SKIDDERS 75 S B 8,000 0.15 0.80
P35 0.00 PIPELAYERS 70 A B 14,000 0.20 0.95
P35 0.00 PIPELAYERS 70 S B 11,500 0.20 1.10
R30 0.00 ROLLERS, STATIC, SELF-PROPELLED 1
R30 0.03 TAMPING FOOT, LANDFILL & SOIL COMPACTORS 55 A B 12,000 0.20 0.80
S10 0.00 SCRAPERS, ELEVATING 1
S10 0.01 0 THRU 200 HP 60 A B 10,000 0.20 0.90
S10 0.01 0 THRU 200 HP 60 S B 8,000 0.20 1.00
shown
3 here.
K-3
EP 1110-1-8
(Vol. 1)
EP 1110-1-8, Vol. 2
4/30/2014
30 Apr 14 APPENDIX K
S10 0.02 OVER 200 HP 60 A B 13,000 0.25 0.95

S10 0.02 OVER 200 HP 60 S B 11,500 0.25 1.00
S15 0.00 SCRAPERS, CONVENTIONAL 60 A B 15,000 0.20 0.80
S15 0.00 SCRAPERS, CONVENTIONAL 60 S B 12,500 0.20 0.85
S20 0.00 SCRAPERS, TANDEM POWERED 60 A B 15,000 0.20 0.85
S20 0.00 SCRAPERS, TANDEM POWERED 60 S B 13,500 0.20 0.90
S25 0.00 SCRAPERS, TRACTOR DRAWN 60 A B 12,000 0.20 0.70
S25 0.00 SCRAPERS, TRACTOR DRAWN 60 S B 10,000 0.20 0.75
T15 0.00 TRACTORS, CRAWLER (DOZER) (includes blade) 1
T15 0.01 0 THRU 225 HP 70 A B 10,000 0.30 1.10
T15 0.01 0 THRU 225 HP 70 S B 8,000 0.30 1.25
T15 0.02 226 HP THRU 425 HP 70 A B 12,500 0.25 1.20
T15 0.02 226 HP THRU 425 HP 70 S B 10,500 0.25 1.25
T15 0.03 OVER 425 HP 70 A B 15,000 0.20 1.20
T15 0.03 OVER 425 HP 70 S B 12,500 0.20 1.35
T20 0.00 TRACTORS, WHEEL TYPE (DOZER) 75 A B 14,000 0.15 0.60
T20 0.00 TRACTORS, WHEEL TYPE (DOZER) 75 S B 13,000 0.15 0.65
shown
4 here.
K-4
EP 1110-1-8, Vol. 2
30 Apr 14
APPENDIX L
EP
Octpb GUIDE FOR ESTIMATING DRILL STEEL AND DRILL BIT COSTS
Guide for Estimating

Drill Steel
and
Drill Bit Costs
Prepared for the

US Army Corps of Engineers, Walla Walla District
By Western Mine Engineering, Inc in cooperation
with Aventurine Engineering, Inc. 2006
August 2006
L-1
EP 1110-1-8, Vol. 2
30 Apr 14
EP Cost Assumptions for

Octpb Drill Steel and Drill Bit
General:
The approach to defining the scope of this cost guide was to confine the work to the basic
drilling process and attendant drill bit and steel lives and costs. This not only simplified
the study parameters but also ensured that future users of the study results could readily
modify the data to suit their individual needs.
1. The steel costs reflect the cost of drilling steel only. All ancillary equipment such as
couplings, striking bars, and hammer maintenance items were not included.
2. The bit life is indicative of the total life of each bit to include up to 10
sharpenings/grindings per bit. The bit costs, however, are list prices for each bit
and do not reflect the costs associated with this process.
3. Costs for both bits and steel are list pricing based on manufacturers’ catalogs or
quotes. No additional materials, equipment costs, or other associated costs are
included. No discounts were applied to the catalog list prices. Estimators will have
to determine an appropriate discount for their individual cases. All prices are based
on current, 2006 costs.
4. The bit and steel lives and penetration rates are based on time the bit is engaged in
the hole. Adjustment for setup, tear down, and moving time between holes has
not been considered.
5. Appropriate bits were identified primarily by drill type and then list prices were
determined from manufacturers’ catalogs. All bits were button type; with threaded
button bits used for the top hammer percussion drills, down the hole (DTH) button
bits for “DTH” drills, and tungsten carbide button, roller bits selected for rotary
drills.
6. Large rotary drills often use 20' or longer drilling steel. It was our belief that most
situations Corps of Engineers estimators face will fall in the range of percussion or
smaller “DTH” drills. In these instances the 12' rod is appropriate. Cursory review
of the costs of longer steel rods suggest that costs for a specific drill steel diameter
do not vary dramatically on a per foot basis for longer rods. Therefore, the
assumption is made that a direct conversion to cost per rod for longer lengths can
be made in proportion to the cost for a 12' length rod. For further information, see
the note at the lower right corner of each of the spreadsheets for a detailed
procedure to make the conversion for rod length and hole depth.
L-2
EP 1110-1-8, Vol. 2
30 Apr 14
EP Example of Estimating
Octpb Drill Steel and Drill Bit Costs
General:
The approach is to define the scope of the work and determine an estimated cost for drill
steel and bits from the answers to the questions below. Follow the simplified steps to
arrive at the estimated costs.
Determine parameters:
1. Determine the type of drilling method – percussion, down the hole (DTH), or
rotary.
2. Determine the manufacturer and model of drilling equipment or determine

equivalency of equipment used in this guide.
3. Determine the material that will be drilled through.
4. Determine the hole diameter of drill.
5. Determine the length of drill rod required to drill hole to the required depth.
Determine costs: (This is an example on how to determine costs)
1. Determine the type of drilling method – down the hole (DTH).
2. Determine the manufacturer/model of drilling equipment – Atlas Copco DM25SP.
3. Determine the material that will be drilled - Basalt .
4. Determine the hole diameter of drill – 5”.
5. Determine the length of drill rod required – 90 feet.
6. Calculate drill steel costs from cost tables:
a. Cost of drill steel $/foot per rod ranges $0.034 to $0.025 Î will use $0.034.
b. Based on 90’ of drilling at 12’ lengths of drill rod – (90’/12’) = 7.5 rods are
required. Round up to next whole number = 8 rods.
c. From drill steel cost adjustment factor chart: for 8 rods the factor is 4.5.
d. From instructions: $0.034 X 4.5 = $0.1530/lf of hole drilled.
7. Determine drill bit costs from cost tables – costs range from $0.55 to $0.40/lf.
L-3
EP 1110-1-8, Vol. 2
30 Apr 14
DRILL MODEL - Atlas Copco ROC D5 - percussion
EP Bit Life (feet/bit) Bit Cost ($/foot)
Octpb 1.75
Hole Diameter (inches)
2.00 2.50 1.75
2.00 2.50
Granite 1,506 - 2,037 1,449 - 1,960 1,359 - 1,838 Granite $0.04 - $0.03 $0.05 - $0.04 $0.07 - $0.05
Basalt 674 - 912 649 - 878 608 - 823 Basalt $0.09 - $0.07 $0.11 - $0.08 $0.16 - $0.12
Gabbro 1,002 - 1,356 964 - 1,305 904 - 1,223 Gabbro $0.06 - $0.05 $0.07 - $0.05 $0.11 - $0.08
Shale 1,427 - 1,931 1,373 - 1,858 1,287 - 1,742 Shale $0.04 - $0.03 $0.05 - $0.04 $0.08 - $0.06
Sandstone 524 - 709 504 - 682 473 - 639 Sandstone $0.12 - $0.09 $0.14 - $0.10 $0.21 - $0.15
Siltstone 3,779 - 5,112 3,636 - 4,919 3,409 - 4,612 Siltstone $0.02 - $0.01 $0.02 - $0.01 $0.03 - $0.02
Conglomer 292 - 395 281 - 380 263 - 356 Conglomer $0.21 - $0.16 $0.25 - $0.18 $0.37 - $0.28
Breccia 2,181 - 2,951 2,099 - 2,839 1,968 - 2,662 Breccia $0.03 - $0.02 $0.03 - $0.02 $0.05 - $0.04
Limestone 1,835 - 2,483 1,766 - 2,389 1,656 - 2,240 Limestone $0.03 - $0.02 $0.04 - $0.03 $0.06 - $0.04
Schist 3,414 - 4,619 3,285 - 4,444 3,080 - 4,167 Schist $0.02 - $0.01 $0.02 - $0.02 $0.03 - $0.02
Slate 1,710 - 2,313 1,645 - 2,226 1,542 - 2,087 Slate $0.04 - $0.03 $0.04 - $0.03 $0.06 - $0.05
Gneiss 735 - 995 707 - 957 663 - 897 Gneiss $0.08 - $0.06 $0.10 - $0.07 $0.15 - $0.11
Drill Steel Life (feet/rod) Drill Steel Cost ($/foot per rod)
Hole Diameter (inches) Hole Diameter (inches)
1.75 2.00 2.50 1.75 2.00 2.50
Granite 2,720 - 3,680 2,617 - 3,541 2,454 - 3,320 Granite $0.103 - $0.076 $0.107 - $0.079 $0.132 - $0.098
Basalt 1,417 - 1,918 1,364 - 1,845 1,279 - 1,730 Basalt $0.198 - $0.146 $0.205 - $0.152 $0.253 - $0.187
Gabbro 1,600 - 2,164 1,539 - 2,083 1,443 - 1,953 Gabbro $0.175 - $0.129 $0.182 - $0.134 $0.224 - $0.166
Shale 2,855 - 3,863 2,747 - 3,717 2,576 - 3,485 Shale $0.098 - $0.072 $0.102 - $0.075 $0.126 - $0.093
Sandstone 2,978 - 4,029 2,865 - 3,877 2,687 - 3,635 Sandstone $0.094 - $0.069 $0.098 - $0.072 $0.121 - $0.089
Conglomer 3,425 - 4,633 3,295 - 4,458 3,090 - 4,180 Conglomer $0.082 - $0.060 $0.085 - $0.063 $0.105 - $0.078
Breccia 4,739 - 6,412 4,560 - 6,170 4,276 - 5,785 Breccia $0.059 - $0.044 $0.061 - $0.045 $0.076 - $0.056
Schist 4,828 - 6,532 4,646 - 6,285 4,356 - 5,893 Schist $0.058 - $0.043 $0.060 - $0.045 $0.074 - $0.055
Slate 3,133 - 4,239 3,015 - 4,079 2,827 - 3,824 Slate $0.089 - $0.066 $0.093 - $0.069 $0.115 - $0.085
Gneiss 2,849 - 3,855 2,742 - 3,709 2,571 - 3,478 Gneiss $0.098 - $0.073 $0.102 - $0.075 $0.126 - $0.093
(Based on 12 foot drilling rod length.)
Penetration Rate (feet/hour) Drill Steel Cost Adjustment Factor

Hole Diameter (inches) As this study is based on 12 foot drilling rod length,
1.75 2.00 2.50 Number of rods Factor the total steel cost per foot of hole drilled depends
Granite 98 - 132 83 - 113 64 - 86 upon the total number of 12 foot sections in the hole.
Basalt 57 - 77 48 - 65 37 - 50 1 1.0 Divide the total hole length by 12 and round this result
Gabbro 63 - 85 53 - 72 41 - 55 2 1.5 up to the next whole number to determine number of
Shale 102 - 138 87 - 117 66 - 90 3 2.0 rods required to drill the hole. Adjust this number to the
Sandstone 105 - 142 90 - 121 69 - 93 4 2.5 average number of rods during drilling by consulting
Siltstone 105 - 142 89 - 121 68 - 92 5 3.0 the Drill Steel Cost Adjustment Factor table to the left.
Conglomer 118 - 160 101 - 136 77 - 104 6 3.5 Multiply this adjustment factor times the cost per foot
Breccia 155 - 210 132 - 179 101 - 137 7 4.0 per rod from the table above. The result is the total
Limestone 133 - 180 113 - 153 86 - 117 8 4.5 drill steel cost per foot of hole drilled. Other drill
Schist 158 - 213 134 - 181 103 - 139 9 5.0 steel lengths may be adjusted for by determining the
Slate 110 - 149 94 - 127 72 - 97 10 5.5 total length of rods required and then converting that
Gneiss 102 - 137 86 - 117 66 - 89 n (n+1)/2 to the number of equivalent 12 foot sections. Once
this is determined follow the procedure outlined above.
Prepared by Western Mine Division, InfoMine USA, Inc. in cooperation with Aventurine Engineering, Inc. 2006
L-4
EP 1110-1-8, Vol. 2
30 Apr 14
DRILL MODEL - Atlas Copco ROC D7 - percussion
Octpb 2.50
3.00 4.00 2.50
3.00 4.00
Granite 1,203 - 1,628 1,115 - 1,509 1,050 - 1,421 Granite $0.08 - $0.06 $0.12 - $0.09 $0.21 - $0.16
Basalt 539 - 729 499 - 676 470 - 636 Basalt $0.18 - $0.13 $0.26 - $0.19 $0.47 - $0.35
Gabbro 801 - 1,083 742 - 1,004 699 - 946 Gabbro $0.12 - $0.09 $0.18 - $0.13 $0.32 - $0.24
Shale 1,140 - 1,542 1,057 - 1,430 995 - 1,347 Shale $0.09 - $0.06 $0.12 - $0.09 $0.22 - $0.17
Breccia 1,742 - 2,357 1,615 - 2,186 1,521 - 2,058 Breccia $0.06 - $0.04 $0.08 - $0.06 $0.15 - $0.11
Schist 2,727 - 3,690 2,528 - 3,421 2,381 - 3,222 Schist $0.04 - $0.03 $0.05 - $0.04 $0.09 - $0.07
Slate 1,366 - 1,848 1,266 - 1,713 1,193 - 1,613 Slate $0.07 - $0.05 $0.10 - $0.08 $0.19 - $0.14
Gneiss 587 - 795 544 - 737 513 - 694 Gneiss $0.17 - $0.12 $0.24 - $0.18 $0.43 - $0.32
2.50 3.00 4.00 2.50 3.00 4.00
Granite 2,173 - 2,940 2,014 - 2,725 1,897 - 2,567 Granite $0.129 - $0.095 $0.161 - $0.119 $0.215 - $0.159
Basalt 1,132 - 1,532 1,050 - 1,420 989 - 1,338 Basalt $0.247 - $0.183 $0.309 - $0.228 $0.412 - $0.304
Gabbro 1,278 - 1,729 1,185 - 1,603 1,116 - 1,510 Gabbro $0.219 - $0.162 $0.273 - $0.202 $0.365 - $0.270
Shale 2,281 - 3,086 2,115 - 2,861 1,992 - 2,695 Shale $0.123 - $0.091 $0.153 - $0.113 $0.204 - $0.151
Breccia 3,786 - 5,122 3,510 - 4,749 3,306 - 4,473 Breccia $0.074 - $0.055 $0.092 - $0.068 $0.123 - $0.091
Schist 3,857 - 5,218 3,576 - 4,838 3,368 - 4,556 Schist $0.073 - $0.054 $0.091 - $0.067 $0.121 - $0.089
Slate 2,503 - 3,386 2,320 - 3,139 2,185 - 2,957 Slate $0.112 - $0.083 $0.140 - $0.103 $0.186 - $0.138
Gneiss 2,276 - 3,080 2,110 - 2,855 1,987 - 2,689 Gneiss $0.123 - $0.091 $0.154 - $0.113 $0.205 - $0.151
(Based on12 foot drilling rod length.)

L-5
EP 1110-1-8, Vol. 2
30 Apr 14
DRILL MODEL - Atlas Copco ECM590 - percussion
Octpb 2.50
3.50 4.50 2.50
3.50 4.50
Granite 1,168 - 1,580 1,060 - 1,434 986 - 1,334 Granite $0.08 - $0.06 $0.15 - $0.11 $0.27 - $0.20
Basalt 523 - 708 475 - 642 441 - 597 Basalt $0.19 - $0.14 $0.34 - $0.25 $0.61 - $0.45
Gabbro 778 - 1,052 706 - 955 656 - 888 Gabbro $0.13 - $0.09 $0.23 - $0.17 $0.41 - $0.30
Shale 1,107 - 1,498 1,005 - 1,359 934 - 1,264 Shale $0.09 - $0.07 $0.16 - $0.12 $0.29 - $0.21
Breccia 1,692 - 2,289 1,535 - 2,077 1,428 - 1,932 Breccia $0.06 - $0.04 $0.10 - $0.08 $0.19 - $0.14
Schist 2,648 - 3,583 2,403 - 3,251 2,235 - 3,024 Schist $0.04 - $0.03 $0.07 - $0.05 $0.12 - $0.09
Slate 1,326 - 1,794 1,203 - 1,628 1,119 - 1,514 Slate $0.07 - $0.05 $0.13 - $0.10 $0.24 - $0.18
Gneiss 570 - 771 517 - 700 481 - 651 Gneiss $0.17 - $0.13 $0.31 - $0.23 $0.56 - $0.41
2.50 3.50 4.50 2.50 3.50 4.50
Granite 2,110 - 2,855 1,915 - 2,590 1,781 - 2,409 Granite $0.154 - $0.114 $0.213 - $0.157 $0.229 - $0.169
Basalt 1,100 - 1,488 998 - 1,350 928 - 1,255 Basalt $0.295 - $0.218 $0.408 - $0.302 $0.439 - $0.324
Gabbro 1,241 - 1,679 1,126 - 1,524 1,047 - 1,417 Gabbro $0.261 - $0.193 $0.361 - $0.267 $0.389 - $0.287
Shale 2,215 - 2,997 2,010 - 2,719 1,869 - 2,529 Shale $0.146 - $0.108 $0.202 - $0.150 $0.218 - $0.161
Breccia 3,676 - 4,974 3,336 - 4,514 3,103 - 4,198 Breccia $0.088 - $0.065 $0.122 - $0.090 $0.131 - $0.097
Schist 3,745 - 5,067 3,399 - 4,598 3,161 - 4,277 Schist $0.087 - $0.064 $0.120 - $0.089 $0.129 - $0.095
Slate 2,430 - 3,288 2,205 - 2,984 2,051 - 2,775 Slate $0.133 - $0.099 $0.185 - $0.136 $0.198 - $0.147
Gneiss 2,210 - 2,990 2,006 - 2,714 1,865 - 2,524 Gneiss $0.147 - $0.108 $0.203 - $0.150 $0.218 - $0.161
(Based pm 12 foot drilling rod length.)

L-6
EP 1110-1-8, Vol. 2
30 Apr 14
DRILL MODEL - Atlas Copco ECM720 - percussion
Octpb 4.00
4.50 5.00 4.00
4.50 5.00
Granite 2,305 - 3,118 2,228 - 3,014 2,161 - 2,924 Granite $0.10 - $0.07 $0.12 - $0.09 $0.15 - $0.11
Basalt 1,032 - 1,396 997 - 1,349 967 - 1,309 Basalt $0.22 - $0.16 $0.27 - $0.20 $0.33 - $0.25
Gabbro 1,534 - 2,075 1,483 - 2,006 1,438 - 1,946 Gabbro $0.15 - $0.11 $0.18 - $0.13 $0.22 - $0.16
Shale 2,184 - 2,955 2,111 - 2,856 2,048 - 2,771 Shale $0.10 - $0.08 $0.13 - $0.09 $0.16 - $0.12
Sandstone 802 - 1,085 775 - 1,048 752 - 1,017 Sandstone $0.28 - $0.21 $0.35 - $0.26 $0.43 - $0.32
Breccia 3,338 - 4,516 3,227 - 4,365 3,130 - 4,235 Breccia $0.07 - $0.05 $0.08 - $0.06 $0.10 - $0.08
Schist 5,225 - 7,069 5,050 - 6,833 4,899 - 6,628 Schist $0.04 - $0.03 $0.05 - $0.04 $0.07 - $0.05
Slate 2,617 - 3,540 2,529 - 3,422 2,453 - 3,319 Slate $0.09 - $0.06 $0.11 - $0.08 $0.13 - $0.10
Gneiss 1,125 - 1,522 1,087 - 1,471 1,055 - 1,427 Gneiss $0.20 - $0.15 $0.25 - $0.18 $0.30 - $0.22
4.00 4.50 5.00 4.00 4.50 5.00
Granite 4,163 - 5,632 4,024 - 5,444 3,903 - 5,281 Granite $0.098 - $0.072 $0.141 - $0.104 $0.146 - $0.108
Basalt 2,169 - 2,935 2,097 - 2,837 2,034 - 2,752 Basalt $0.188 - $0.139 $0.271 - $0.200 $0.279 - $0.206
Gabbro 2,448 - 3,313 2,367 - 3,202 2,296 - 3,106 Gabbro $0.166 - $0.123 $0.240 - $0.177 $0.247 - $0.183
Shale 4,370 - 5,912 4,224 - 5,715 4,097 - 5,544 Shale $0.093 - $0.069 $0.134 - $0.099 $0.139 - $0.102
Breccia 7,253 - 9,813 7,011 - 9,485 6,801 - 9,201 Breccia $0.056 - $0.041 $0.081 - $0.060 $0.084 - $0.062
Schist 7,389 - 9,997 7,142 - 9,663 6,928 - 9,374 Schist $0.055 - $0.041 $0.080 - $0.059 $0.082 - $0.061
Slate 4,795 - 6,487 4,635 - 6,270 4,496 - 6,083 Slate $0.085 - $0.063 $0.123 - $0.091 $0.126 - $0.093
Gneiss 4,361 - 5,900 4,215 - 5,702 4,089 - 5,532 Gneiss $0.093 - $0.069 $0.135 - $0.100 $0.139 - $0.103

L-7
EP 1110-1-8, Vol. 2
30 Apr 14
DRILL MODEL - Atlas Copco DM25SP - DTH
Octpb 3.50
5.00 6.50 3.50
5.00 6.50
Granite 2,498 - 3,380 2,254 - 3,049 2,089 - 2,827 Granite $0.16 - $0.12 $0.24 - $0.18 $0.31 - $0.23
Basalt 1,118 - 1,513 1,009 - 1,365 935 - 1,266 Basalt $0.37 - $0.27 $0.55 - $0.40 $0.68 - $0.51
Gabbro 1,663 - 2,250 1,500 - 2,030 1,391 - 1,882 Gabbro $0.25 - $0.18 $0.37 - $0.27 $0.46 - $0.34
Shale 2,367 - 3,203 2,136 - 2,890 1,980 - 2,679 Shale $0.17 - $0.13 $0.26 - $0.19 $0.32 - $0.24
Sandstone 869 - 1,176 784 - 1,061 727 - 983 Sandstone $0.47 - $0.35 $0.70 - $0.52 $0.88 - $0.65
Breccia 3,618 - 4,896 3,265 - 4,417 3,026 - 4,095 Breccia $0.11 - $0.08 $0.17 - $0.12 $0.21 - $0.16
Schist 5,664 - 7,663 5,110 - 6,913 4,737 - 6,409 Schist $0.07 - $0.05 $0.11 - $0.08 $0.14 - $0.10
Slate 2,836 - 3,837 2,559 - 3,462 2,372 - 3,209 Slate $0.14 - $0.11 $0.21 - $0.16 $0.27 - $0.20
Gneiss 1,219 - 1,650 1,100 - 1,489 1,020 - 1,380 Gneiss $0.34 - $0.25 $0.50 - $0.37 $0.63 - $0.46
3.50 5.00 6.50 3.50 5.00 6.50
Granite 28,996 - 39,229 26,159 - 35,392 24,252 - 32,811 Granite $0.016 - $0.012 $0.020 - $0.015 $0.025 - $0.018
Basalt 16,978 - 22,970 15,317 - 20,723 14,200 - 19,212 Basalt $0.028 - $0.020 $0.034 - $0.025 $0.042 - $0.031
Gabbro 18,752 - 25,371 16,918 - 22,889 15,684 - 21,220 Gabbro $0.025 - $0.018 $0.031 - $0.023 $0.038 - $0.028
Shale 30,177 - 40,827 27,225 - 36,834 25,240 - 34,148 Shale $0.016 - $0.011 $0.019 - $0.014 $0.024 - $0.018
Breccia 45,750 - 61,896 41,275 - 55,842 38,265 - 51,770 Breccia $0.010 - $0.008 $0.013 - $0.009 $0.016 - $0.012
Schist 46,452 - 62,847 41,908 - 56,699 38,852 - 52,565 Schist $0.010 - $0.007 $0.013 - $0.009 $0.015 - $0.011
Slate 32,566 - 44,060 29,381 - 39,750 27,238 - 36,852 Slate $0.014 - $0.011 $0.018 - $0.013 $0.022 - $0.016
Gneiss 30,123 - 40,755 27,177 - 36,768 25,195 - 34,087 Gneiss $0.016 - $0.011 $0.019 - $0.014 $0.024 - $0.018

L-8
EP 1110-1-8, Vol. 2
30 Apr 14
DRILL MODEL - Atlas Copco DM30 -DTH
Octpb 5.50
6.00 6.50 5.50
6.00 6.50
Granite 1,946 - 2,633 1,898 - 2,568 1,855 - 2,509 Granite $0.30 - $0.22 $0.33 - $0.25 $0.35 - $0.26
Basalt 871 - 1,179 850 - 1,150 830 - 1,124 Basalt $0.66 - $0.49 $0.74 - $0.55 $0.77 - $0.57
Gabbro 1,296 - 1,753 1,263 - 1,709 1,235 - 1,670 Gabbro $0.44 - $0.33 $0.50 - $0.37 $0.52 - $0.38
Shale 1,845 - 2,496 1,799 - 2,434 1,758 - 2,378 Shale $0.31 - $0.23 $0.35 - $0.26 $0.36 - $0.27
Breccia 2,819 - 3,814 2,749 - 3,720 2,687 - 3,635 Breccia $0.20 - $0.15 $0.23 - $0.17 $0.24 - $0.18
Schist 4,413 - 5,970 4,303 - 5,822 4,205 - 5,689 Schist $0.13 - $0.10 $0.15 - $0.11 $0.15 - $0.11
Slate 2,210 - 2,990 2,155 - 2,916 2,106 - 2,849 Slate $0.26 - $0.19 $0.29 - $0.22 $0.30 - $0.22
Gneiss 950 - 1,285 927 - 1,254 905 - 1,225 Gneiss $0.61 - $0.45 $0.68 - $0.50 $0.71 - $0.52
5.50 6.00 6.50 5.50 6.00 6.50
Granite 26,110 - 35,326 25,463 - 34,450 24,881 - 33,663 Granite $0.020 - $0.015 $0.024 - $0.017 $0.029 - $0.021
Basalt 15,288 - 20,684 14,909 - 20,171 14,569 - 19,711 Basalt $0.034 - $0.025 $0.040 - $0.030 $0.050 - $0.037
Gabbro 16,886 - 22,846 16,468 - 22,280 16,092 - 21,771 Gabbro $0.031 - $0.023 $0.036 - $0.027 $0.045 - $0.033
Shale 27,174 - 36,765 26,500 - 35,853 25,895 - 35,034 Shale $0.019 - $0.014 $0.023 - $0.017 $0.028 - $0.021
Breccia 41,197 - 55,738 40,176 - 54,355 39,258 - 53,114 Breccia $0.013 - $0.009 $0.015 - $0.011 $0.018 - $0.014
Schist 41,830 - 56,593 40,792 - 55,190 39,861 - 53,929 Schist $0.013 - $0.009 $0.015 - $0.011 $0.018 - $0.013
Slate 29,326 - 39,676 28,599 - 38,692 27,945 - 37,809 Slate $0.018 - $0.013 $0.021 - $0.015 $0.026 - $0.019
Gneiss 27,126 - 36,700 26,453 - 35,790 25,849 - 34,972 Gneiss $0.019 - $0.014 $0.023 - $0.017 $0.028 - $0.021

L-9
EP 1110-1-8, Vol. 2
30 Apr 14
DRILL MODEL - Atlas Copco DM45 -DTH
Octpb 5.00
6.50 8.00 5.00
6.50 8.00
Granite 2,580 - 3,490 2,392 - 3,236 2,253 - 3,048 Granite $0.21 - $0.16 $0.27 - $0.20 $0.55 - $0.40
Basalt 1,155 - 1,563 1,071 - 1,449 1,009 - 1,364 Basalt $0.48 - $0.35 $0.60 - $0.44 $1.22 - $0.90
Gabbro 1,717 - 2,323 1,592 - 2,154 1,499 - 2,029 Gabbro $0.32 - $0.24 $0.40 - $0.30 $0.82 - $0.61
Shale 2,445 - 3,308 2,267 - 3,067 2,135 - 2,888 Shale $0.22 - $0.17 $0.28 - $0.21 $0.58 - $0.43
Sandstone 897 - 1,214 832 - 1,126 784 - 1,060 Sandstone $0.61 - $0.45 $0.77 - $0.57 $1.57 - $1.16
Breccia 3,737 - 5,056 3,464 - 4,687 3,263 - 4,414 Breccia $0.15 - $0.11 $0.18 - $0.14 $0.38 - $0.28
Schist 5,849 - 7,913 5,422 - 7,336 5,107 - 6,910 Schist $0.09 - $0.07 $0.12 - $0.09 $0.24 - $0.18
Slate 2,929 - 3,963 2,715 - 3,674 2,557 - 3,460 Slate $0.19 - $0.14 $0.24 - $0.17 $0.48 - $0.36
Gneiss 1,259 - 1,704 1,168 - 1,580 1,100 - 1,488 Gneiss $0.44 - $0.32 $0.55 - $0.41 $1.12 - $0.83
5.00 6.50 8.00 5.00 6.50 8.00
Granite 28,482 - 38,534 26,405 - 35,724 24,869 - 33,646 Granite $0.021 - $0.016 $0.027 - $0.020 $0.029 - $0.021
Basalt 16,677 - 22,563 15,461 - 20,917 14,561 - 19,701 Basalt $0.036 - $0.027 $0.047 - $0.035 $0.050 - $0.037
Gabbro 18,420 - 24,921 17,077 - 23,104 16,083 - 21,760 Gabbro $0.033 - $0.024 $0.042 - $0.031 $0.045 - $0.033
Shale 29,642 - 40,104 27,480 - 37,179 25,882 - 35,017 Shale $0.020 - $0.015 $0.026 - $0.019 $0.028 - $0.021
Breccia 44,939 - 60,799 41,662 - 56,366 39,238 - 53,087 Breccia $0.013 - $0.010 $0.017 - $0.013 $0.018 - $0.014
Schist 45,628 - 61,733 42,301 - 57,231 39,841 - 53,902 Schist $0.013 - $0.010 $0.017 - $0.013 $0.018 - $0.013
Slate 31,989 - 43,279 29,656 - 40,123 27,931 - 37,789 Slate $0.019 - $0.014 $0.024 - $0.018 $0.026 - $0.019
Gneiss 29,589 - 40,032 27,432 - 37,113 25,836 - 34,955 Gneiss $0.020 - $0.015 $0.026 - $0.019 $0.028 - $0.021

L-10
EP 1110-1-8, Vol. 2
30 Apr 14
DRILL MODEL - Atlas Copco DM M2 -DTH
Octpb 8.88
10.00 11.875 8.88
10.00 11.875
Granite 1,779 - 2,407 1,719 - 2,325 1,636 - 2,213 Granite $0.78 - $0.58 $1.11 - $0.82 $2.75 - $2.03
Basalt 796 - 1,078 770 - 1,041 732 - 991 Basalt $1.74 - $1.29 $2.47 - $1.82 $6.15 - $4.54
Gabbro 1,184 - 1,602 1,144 - 1,548 1,089 - 1,473 Gabbro $1.17 - $0.86 $1.66 - $1.23 $4.13 - $3.06
Shale 1,686 - 2,281 1,629 - 2,204 1,550 - 2,097 Shale $0.82 - $0.61 $1.17 - $0.86 $2.90 - $2.15
Breccia 2,577 - 3,486 2,490 - 3,368 2,369 - 3,205 Breccia $0.54 - $0.40 $0.76 - $0.56 $1.90 - $1.40
Schist 4,033 - 5,457 3,897 - 5,272 3,708 - 5,017 Schist $0.34 - $0.25 $0.49 - $0.36 $1.21 - $0.90
Slate 2,020 - 2,733 1,951 - 2,640 1,857 - 2,512 Slate $0.69 - $0.51 $0.97 - $0.72 $2.42 - $1.79
Gneiss 868 - 1,175 839 - 1,135 798 - 1,080 Gneiss $1.59 - $1.18 $2.26 - $1.67 $5.64 - $4.17
8.88 10.00 11.875 8.88 10.00 11.875
Granite 25,947 - 35,105 25,069 - 33,917 23,856 - 32,276 Granite $0.038 - $0.028 $0.040 - $0.029 $0.042 - $0.031
Basalt 15,193 - 20,555 14,679 - 19,859 13,968 - 18,898 Basalt $0.065 - $0.048 $0.068 - $0.050 $0.071 - $0.053
Gabbro 16,781 - 22,704 16,213 - 21,935 15,428 - 20,874 Gabbro $0.059 - $0.044 $0.061 - $0.045 $0.064 - $0.048
Shale 27,004 - 36,535 26,090 - 35,298 24,828 - 33,590 Shale $0.037 - $0.027 $0.038 - $0.028 $0.040 - $0.030
Breccia 40,940 - 55,390 39,554 - 53,514 37,640 - 50,925 Breccia $0.024 - $0.018 $0.025 - $0.019 $0.026 - $0.020
Schist 41,569 - 56,240 40,161 - 54,336 38,218 - 51,707 Schist $0.024 - $0.018 $0.025 - $0.018 $0.026 - $0.019
Slate 29,143 - 39,428 28,156 - 38,093 26,794 - 36,250 Slate $0.034 - $0.025 $0.035 - $0.026 $0.037 - $0.027
Gneiss 26,957 - 36,471 26,044 - 35,236 24,784 - 33,531 Gneiss $0.037 - $0.027 $0.038 - $0.028 $0.040 - $0.030

L-11
EP 1110-1-8, Vol. 2
30 Apr 14
DRILL MODEL - Atlas Copco DM25SP - Rotary
Octpb 3.88
5.00 6.25 3.88
5.00 6.25
Granite 3,585 - 4,851 3,364 - 4,552 3,182 - 4,305 Granite $0.32 - $0.24 $0.48 - $0.36 $0.69 - $0.51
Basalt 1,878 - 2,541 1,762 - 2,384 1,667 - 2,255 Basalt $0.61 - $0.45 $0.92 - $0.68 $1.32 - $0.98
Gabbro 2,118 - 2,865 1,987 - 2,689 1,880 - 2,543 Gabbro $0.54 - $0.40 $0.82 - $0.61 $1.17 - $0.87
Shale 3,762 - 5,090 3,531 - 4,777 3,339 - 4,518 Shale $0.31 - $0.23 $0.46 - $0.34 $0.66 - $0.49
Breccia 6,220 - 8,415 5,836 - 7,896 5,520 - 7,468 Breccia $0.18 - $0.14 $0.28 - $0.21 $0.40 - $0.30
Schist 6,335 - 8,571 5,945 - 8,043 5,623 - 7,607 Schist $0.18 - $0.13 $0.27 - $0.20 $0.39 - $0.29
Slate 4,125 - 5,581 3,871 - 5,237 3,661 - 4,953 Slate $0.28 - $0.21 $0.42 - $0.31 $0.60 - $0.45
Gneiss 3,754 - 5,079 3,523 - 4,766 3,332 - 4,508 Gneiss $0.31 - $0.23 $0.46 - $0.34 $0.66 - $0.49
3.88 5.00 6.25 3.88 5.00 6.25
Granite 44,519 - 60,232 41,775 - 56,519 39,512 - 53,457 Granite $0.012 - $0.009 $0.038 - $0.028 $0.047 - $0.035
Basalt 26,067 - 35,267 24,460 - 33,093 23,135 - 31,301 Basalt $0.020 - $0.015 $0.065 - $0.048 $0.081 - $0.060
Gabbro 28,792 - 38,954 27,017 - 36,552 25,553 - 34,572 Gabbro $0.018 - $0.014 $0.059 - $0.043 $0.073 - $0.054
Shale 46,333 - 62,685 43,477 - 58,821 41,121 - 55,635 Shale $0.011 - $0.008 $0.036 - $0.027 $0.046 - $0.034
Breccia 70,243 - 95,034 65,913 - 89,176 62,342 - 84,345 Breccia $0.007 - $0.006 $0.024 - $0.018 $0.030 - $0.022
Schist 71,321 - 96,493 66,925 - 90,545 63,299 - 85,640 Schist $0.007 - $0.005 $0.024 - $0.017 $0.030 - $0.022
Slate 50,001 - 67,649 46,919 - 63,479 44,377 - 60,040 Slate $0.011 - $0.008 $0.034 - $0.025 $0.042 - $0.031
Gneiss 46,250 - 62,574 43,400 - 58,717 41,048 - 55,536 Gneiss $0.011 - $0.008 $0.036 - $0.027 $0.046 - $0.034

L-12
EP 1110-1-8, Vol. 2
30 Apr 14
DRILL MODEL - Atlas Copco DM30 -Rotary
Octpb 5.50
6.00 6.75 5.50
6.00 6.75
Granite 3,347 - 4,528 3,275 - 4,431 3,180 - 4,302 Granite $0.59 - $0.44 $0.65 - $0.48 $0.77 - $0.57
Basalt 1,753 - 2,372 1,716 - 2,321 1,666 - 2,254 Basalt $1.12 - $0.83 $1.24 - $0.92 $1.48 - $1.09
Gabbro 1,977 - 2,675 1,934 - 2,617 1,878 - 2,541 Gabbro $1.00 - $0.74 $1.10 - $0.81 $1.31 - $0.97
Shale 3,512 - 4,752 3,437 - 4,649 3,337 - 4,515 Shale $0.56 - $0.42 $0.62 - $0.46 $0.74 - $0.55
Breccia 5,806 - 7,855 5,681 - 7,686 5,516 - 7,463 Breccia $0.34 - $0.25 $0.38 - $0.28 $0.45 - $0.33
Schist 5,913 - 8,000 5,786 - 7,829 5,619 - 7,602 Schist $0.33 - $0.25 $0.37 - $0.27 $0.44 - $0.32
Slate 3,851 - 5,210 3,768 - 5,098 3,659 - 4,950 Slate $0.51 - $0.38 $0.57 - $0.42 $0.67 - $0.50
Gneiss 3,504 - 4,741 3,429 - 4,639 3,330 - 4,505 Gneiss $0.56 - $0.42 $0.62 - $0.46 $0.74 - $0.55
5.50 6.00 6.75 5.50 6.00 6.75
Granite 41,556 - 56,222 40,663 - 55,014 39,485 - 53,421 Granite $0.045 - $0.033 $0.046 - $0.034 $0.047 - $0.035
Basalt 24,332 - 32,920 23,809 - 32,212 23,119 - 31,279 Basalt $0.077 - $0.057 $0.079 - $0.058 $0.081 - $0.060
Gabbro 26,875 - 36,360 26,298 - 35,579 25,536 - 34,549 Gabbro $0.070 - $0.051 $0.071 - $0.053 $0.073 - $0.054
Shale 43,248 - 58,513 42,319 - 57,255 41,093 - 55,597 Shale $0.043 - $0.032 $0.044 - $0.033 $0.046 - $0.034
Breccia 65,567 - 88,708 64,158 - 86,802 62,299 - 84,288 Breccia $0.029 - $0.021 $0.029 - $0.022 $0.030 - $0.022
Schist 66,573 - 90,070 65,143 - 88,135 63,256 - 85,582 Schist $0.028 - $0.021 $0.029 - $0.021 $0.030 - $0.022
Slate 46,673 - 63,146 45,670 - 61,789 44,347 - 59,999 Slate $0.040 - $0.030 $0.041 - $0.030 $0.042 - $0.031
Gneiss 43,172 - 58,409 42,244 - 57,154 41,020 - 55,498 Gneiss $0.043 - $0.032 $0.044 - $0.033 $0.046 - $0.034

L-13
EP 1110-1-8, Vol. 2
30 Apr 14
DRILL MODEL - Atlas Copco DM45 -Rotary
Octpb 5.00
6.75 7.875 5.00
6.75 7.875
Granite 3,619 - 4,897 3,358 - 4,543 3,231 - 4,372 Granite $0.45 - $0.33 $0.73 - $0.54 $0.94 - $0.69
Basalt 1,896 - 2,565 1,759 - 2,380 1,693 - 2,290 Basalt $0.86 - $0.64 $1.40 - $1.03 $1.79 - $1.32
Gabbro 2,138 - 2,893 1,984 - 2,684 1,909 - 2,582 Gabbro $0.76 - $0.56 $1.24 - $0.92 $1.58 - $1.17
Shale 3,798 - 5,139 3,524 - 4,768 3,391 - 4,588 Shale $0.43 - $0.32 $0.70 - $0.52 $0.89 - $0.66
Breccia 6,279 - 8,495 5,825 - 7,881 5,606 - 7,584 Breccia $0.26 - $0.19 $0.42 - $0.31 $0.54 - $0.40
Schist 6,395 - 8,652 5,934 - 8,028 5,710 - 7,725 Schist $0.25 - $0.19 $0.42 - $0.31 $0.53 - $0.39
Slate 4,164 - 5,634 3,864 - 5,228 3,718 - 5,030 Slate $0.39 - $0.29 $0.64 - $0.47 $0.81 - $0.60
Gneiss 3,790 - 5,128 3,517 - 4,758 3,384 - 4,578 Gneiss $0.43 - $0.32 $0.70 - $0.52 $0.89 - $0.66
5.00 6.75 7.875 5.00 6.75 7.875
Granite 44,942 - 60,803 41,698 - 56,415 40,124 - 54,286 Granite $0.035 - $0.026 $0.045 - $0.033 $0.069 - $0.051
Basalt 26,314 - 35,602 24,415 - 33,033 23,494 - 31,786 Basalt $0.060 - $0.044 $0.077 - $0.057 $0.117 - $0.087
Gabbro 29,065 - 39,323 26,967 - 36,485 25,950 - 35,108 Gabbro $0.054 - $0.040 $0.069 - $0.051 $0.106 - $0.079
Shale 46,772 - 63,280 43,397 - 58,713 41,759 - 56,497 Shale $0.034 - $0.025 $0.043 - $0.032 $0.066 - $0.049
Breccia 70,909 - 95,936 65,792 - 89,013 63,309 - 85,653 Breccia $0.022 - $0.017 $0.028 - $0.021 $0.044 - $0.032
Schist 71,998 - 97,409 66,802 - 90,379 64,280 - 86,968 Schist $0.022 - $0.016 $0.028 - $0.021 $0.043 - $0.032
Slate 50,476 - 68,291 46,833 - 63,362 45,065 - 60,971 Slate $0.031 - $0.023 $0.040 - $0.030 $0.061 - $0.045
Gneiss 46,689 - 63,168 43,320 - 58,609 41,685 - 56,397 Gneiss $0.034 - $0.025 $0.043 - $0.032 $0.066 - $0.049

L-14
EP 1110-1-8, Vol. 2
30 Apr 14
DRILL MODEL - Atlas Copco DM M2 -Rotary
Octpb 9.00
9.875 11.00 9.00
9.875 11.00
Granite 3,312 - 4,481 3,236 - 4,378 3,150 - 4,262 Granite $1.08 - $0.80 $1.48 - $1.09 $1.79 - $1.32
Basalt 1,735 - 2,347 1,695 - 2,294 1,650 - 2,233 Basalt $2.07 - $1.53 $2.82 - $2.09 $3.42 - $2.53
Gabbro 1,956 - 2,647 1,912 - 2,586 1,861 - 2,518 Gabbro $1.83 - $1.36 $2.50 - $1.85 $3.03 - $2.24
Shale 3,476 - 4,702 3,396 - 4,595 3,306 - 4,473 Shale $1.03 - $0.76 $1.41 - $1.04 $1.71 - $1.26
Breccia 5,745 - 7,773 5,614 - 7,595 5,465 - 7,393 Breccia $0.62 - $0.46 $0.85 - $0.63 $1.03 - $0.76
Schist 5,852 - 7,917 5,718 - 7,736 5,566 - 7,531 Schist $0.61 - $0.45 $0.84 - $0.62 $1.01 - $0.75
Slate 3,811 - 5,156 3,723 - 5,038 3,624 - 4,904 Slate $0.94 - $0.70 $1.29 - $0.95 $1.56 - $1.15
Gneiss 3,468 - 4,692 3,389 - 4,585 3,299 - 4,463 Gneiss $1.03 - $0.76 $1.41 - $1.04 $1.71 - $1.26
9.00 9.875 11.00 9.00 9.875 11.00
Granite 41,124 - 55,639 40,183 - 54,365 39,115 - 52,921 Granite $0.067 - $0.050 $0.069 - $0.051 $0.070 - $0.051
Basalt 24,079 - 32,578 23,528 - 31,832 22,903 - 30,986 Basalt $0.115 - $0.085 $0.117 - $0.087 $0.119 - $0.088
Gabbro 26,596 - 35,983 25,987 - 35,159 25,297 - 34,225 Gabbro $0.104 - $0.077 $0.106 - $0.078 $0.108 - $0.079
Shale 42,800 - 57,905 41,820 - 56,580 40,709 - 55,077 Shale $0.064 - $0.048 $0.066 - $0.049 $0.067 - $0.049
Breccia 64,887 - 87,788 63,401 - 85,778 61,717 - 83,499 Breccia $0.043 - $0.031 $0.044 - $0.032 $0.044 - $0.033
Schist 65,883 - 89,135 64,374 - 87,095 62,664 - 84,781 Schist $0.042 - $0.031 $0.043 - $0.032 $0.043 - $0.032
Slate 46,189 - 62,490 45,131 - 61,060 43,932 - 59,438 Slate $0.060 - $0.044 $0.061 - $0.045 $0.062 - $0.046
Gneiss 42,724 - 57,803 41,746 - 56,479 40,637 - 54,979 Gneiss $0.065 - $0.048 $0.066 - $0.049 $0.067 - $0.049

L-15
EP 1110-1-8, Vol. 2
30 Apr 14
DRILL MODEL - Bucyrus International 59R -Rotary
Octpb 12.25
15.00 16.00 12.25
15.00 16.00
Granite 3379.984 - 4572.919 3213.372 - 4347.504 3162.023 - 4278.031 Granite $1.95 - $1.44 $3.23 - $2.38 $3.48 - $2.58
Basalt 1770.653 - 2395.589 1683.371 - 2277.502 1656.471 - 2241.108 Basalt $3.73 - $2.76 $6.16 - $4.55 $6.65 - $4.92
Gabbro 1996.573 - 2701.246 1898.155 - 2568.092 1867.823 - 2527.054 Gabbro $3.31 - $2.44 $5.46 - $4.04 $5.90 - $4.36
Shale 3546.993 - 4798.873 3372.149 - 4562.319 3318.263 - 4489.414 Shale $1.86 - $1.38 $3.07 - $2.27 $3.32 - $2.45
Sandstone 3697.769 - 5002.863 3515.492 - 4756.254 3459.315 - 4680.25 Sandstone $1.79 - $1.32 $2.95 - $2.18 $3.18 - $2.35
Siltstone 3681.304 - 4980.588 3499.839 - 4735.076 3443.912 - 4659.411 Siltstone $1.79 - $1.33 $2.96 - $2.19 $3.20 - $2.36
Conglomer 4247.818 - 5747.048 4038.427 - 5463.755 3973.894 - 5376.445 Conglomer $1.55 - $1.15 $2.57 - $1.90 $2.77 - $2.05
Breccia 5863.339 - 7932.753 5574.314 - 7541.719 5485.238 - 7421.204 Breccia $1.13 - $0.83 $1.86 - $1.37 $2.01 - $1.48
Limestone 4870.335 - 6589.277 4630.259 - 6264.468 4556.268 - 6164.363 Limestone $1.36 - $1.00 $2.24 - $1.65 $2.42 - $1.79
Schist 5972.24 - 8080.09 5677.846 - 7681.792 5587.116 - 7559.039 Schist $1.11 - $0.82 $1.83 - $1.35 $1.97 - $1.46
Slate 3888.976 - 5261.555 3697.274 - 5002.194 3638.192 - 4922.26 Slate $1.70 - $1.25 $2.80 - $2.07 $3.03 - $2.24
Gneiss 3539.394 - 4788.591 3364.924 - 4552.544 3311.153 - 4479.796 Gneiss $1.87 - $1.38 $3.08 - $2.28 $3.33 - $2.46
12.25 15.00 16.00 12.25 15.00 16.00
Granite 41969.55 - 56782.33 39900.72 - 53983.32 39263.11 - 53120.68 Granite $0.078 - $0.058 $0.082 - $0.061 $0.083 - $0.062
Basalt 24574.25 - 33247.51 23362.89 - 31608.62 22989.56 - 31103.52 Basalt $0.133 - $0.098 $0.140 - $0.104 $0.142 - $0.105
Gabbro 27142.87 - 36722.71 25804.9 - 34912.52 25392.55 - 34354.62 Gabbro $0.121 - $0.089 $0.127 - $0.094 $0.129 - $0.095
Shale 43679.22 - 59095.42 41526.11 - 56182.39 40862.54 - 55284.61 Shale $0.075 - $0.055 $0.079 - $0.058 $0.080 - $0.059
Sandstone 45210.83 - 61167.6 42982.23 - 58152.42 42295.38 - 57223.16 Sandstone $0.072 - $0.054 $0.076 - $0.056 $0.077 - $0.057
Siltstone 45044.11 - 60942.03 42823.72 - 57937.98 42139.41 - 57012.14 Siltstone $0.073 - $0.054 $0.076 - $0.056 $0.078 - $0.057
Conglomer 50711.07 - 68609.09 48211.33 - 65227.1 47440.93 - 64184.78 Conglomer $0.065 - $0.048 $0.068 - $0.050 $0.069 - $0.051
Breccia 66219.99 - 89591.75 62955.76 - 85175.45 61949.75 - 83814.36 Breccia $0.049 - $0.037 $0.052 - $0.038 $0.053 - $0.039
Limestone 56790.17 - 76833.76 53990.78 - 73046.35 53128.02 - 71879.08 Limestone $0.058 - $0.043 $0.061 - $0.045 $0.062 - $0.046
Schist 67236.6 - 90967.16 63922.26 - 86483.06 62900.8 - 85101.08 Schist $0.049 - $0.036 $0.051 - $0.038 $0.052 - $0.038
Slate 47137.81 - 63774.69 44814.22 - 60631 44098.1 - 59662.13 Slate $0.069 - $0.051 $0.073 - $0.054 $0.074 - $0.055
Gneiss 43601.73 - 58990.58 41452.44 - 56082.72 40790.04 - 55186.53 Gneiss $0.075 - $0.055 $0.079 - $0.058 $0.080 - $0.059

Granite 19.00236 - 25.70907 12.60139 - 17.04894 11.05531 - 14.95719 upon the total number of 12 foot sections in the hole.
Basalt 11.03265 - 14.92652 7.316286 - 9.898504 6.418644 - 8.684048 1 1.0 Divide the total hole length by 12 and round this result
Gabbro 12.205 - 16.51264 8.093728 - 10.95034 7.100701 - 9.606831 2 1.5 up to the next whole number to determine number of
Shale 19.78892 - 26.77325 13.123 - 17.75464 11.51293 - 15.57631 3 2.0 rods required to drill the hole. Adjust this number to the
Sandstone 20.49398 - 27.72715 13.59055 - 18.38722 11.92312 - 16.13128 4 2.5 average number of rods during drilling by consulting
Siltstone 20.41721 - 27.62329 13.53965 - 18.31835 11.87846 - 16.07085 5 3.0 the Drill Steel Cost Adjustment Factor table to the left.
Conglomer 23.02897 - 31.15684 15.27163 - 20.66162 13.39794 - 18.12663 6 3.5 Multiply this adjustment factor times the cost per foot
Breccia 30.19898 - 40.85745 20.02642 - 27.09456 17.56936 - 23.77031 7 4.0 per rod from the table above. The result is the total
Limestone 25.83581 - 34.95433 17.13298 - 23.17992 15.03092 - 20.33595 8 4.5 drill steel cost per foot of hole drilled. Other drill
Schist 30.66998 - 41.49468 20.33876 - 27.51714 17.84338 - 24.14104 9 5.0 steel lengths may be adjusted for by determining the
Slate 21.38157 - 28.92801 14.17916 - 19.18357 12.43951 - 16.82992 10 5.5 total length of rods required and then converting that
Gneiss 19.75326 - 26.725 13.09935 - 17.72265 11.49218 - 15.54824 n (n+1)/2 to the number of equivalent 12 foot sections. Once
L-16
EP 1110-1-8, Vol. 2
30 Apr 14
DRILL MODEL - Atlas Copco TBH4 - Rotary
Octpb 5.00
6.750 7.875 5.00
6.750 7.875
Granite 3,526 - 4,770 3,271 - 4,426 3,148 - 4,259 Granite $0.46 - $0.34 $0.75 - $0.56 $0.96 - $0.71
Basalt 1,847 - 2,499 1,714 - 2,319 1,649 - 2,231 Basalt $0.88 - $0.65 $1.44 - $1.06 $1.83 - $1.35
Gabbro 2,083 - 2,818 1,932 - 2,614 1,859 - 2,516 Gabbro $0.78 - $0.58 $1.27 - $0.94 $1.63 - $1.20
Shale 3,700 - 5,006 3,433 - 4,645 3,303 - 4,469 Shale $0.44 - $0.33 $0.72 - $0.53 $0.92 - $0.68
Breccia 6,116 - 8,275 5,675 - 7,678 5,461 - 7,388 Breccia $0.27 - $0.20 $0.43 - $0.32 $0.55 - $0.41
Schist 6,230 - 8,429 5,780 - 7,820 5,562 - 7,525 Schist $0.26 - $0.19 $0.43 - $0.31 $0.54 - $0.40
Slate 4,057 - 5,488 3,764 - 5,092 3,622 - 4,900 Slate $0.40 - $0.30 $0.65 - $0.48 $0.83 - $0.62
Gneiss 3,692 - 4,995 3,426 - 4,635 3,296 - 4,460 Gneiss $0.44 - $0.33 $0.72 - $0.53 $0.92 - $0.68
5.00 6.750 7.875 5.00 6.750 7.875
Granite 43,780 - 59,231 40,620 - 54,957 39,087 - 52,882 Granite $0.036 - $0.027 $0.046 - $0.034 $0.071 - $0.052
Basalt 25,634 - 34,681 23,784 - 32,178 22,886 - 30,964 Basalt $0.062 - $0.046 $0.079 - $0.058 $0.121 - $0.089
Gabbro 28,313 - 38,306 26,270 - 35,542 25,279 - 34,200 Gabbro $0.056 - $0.041 $0.071 - $0.053 $0.109 - $0.081
Shale 45,563 - 61,644 42,275 - 57,195 40,679 - 55,036 Shale $0.035 - $0.026 $0.044 - $0.033 $0.068 - $0.050
Breccia 69,076 - 93,456 64,091 - 86,711 61,672 - 83,438 Breccia $0.023 - $0.017 $0.029 - $0.022 $0.045 - $0.033
Schist 70,136 - 94,890 65,075 - 88,042 62,618 - 84,719 Schist $0.023 - $0.017 $0.029 - $0.021 $0.044 - $0.033
Slate 49,171 - 66,525 45,622 - 61,724 43,900 - 59,394 Slate $0.032 - $0.024 $0.041 - $0.030 $0.063 - $0.046
Gneiss 45,482 - 61,535 42,200 - 57,094 40,607 - 54,939 Gneiss $0.035 - $0.026 $0.044 - $0.033 $0.068 - $0.050

L-17
EP 1110-1-8, Vol. 2
30 Apr 14
BIT AND DRILL STEEL PRICE DATABASE

EP
Effective date - 8/2006
Octpb
Drill Bits Drill Rod
Bit Type Bit Size Bit Price Rod Type Rod Size Rod Price
Button - drop center Percussion rod - 12 ft
1-3/4" $62 R32 $280
2" $69 T38 $324
2-1.2" $98 T45 $407
3" $131 T51 $568
3-1.2" $159
4" $223 DTH rod - 9'10"
4-1.2" $268 3.0 76mm $384
5" $321 3.5 89mm $431
4.0 102mm $491
DTH - concave face 4.5 114mm $592
3-1/2" $410 5.5 140mm $815
5" $550
5-1/2" $575 Rotary rod - 25' to 30'
6" $630 4" x 25' $3,300
6-1/2" $640 5" x 25' $3,900
8" $1,230 7" x 30' $6,900
8-7/8" $1,385 8-5/8" x 30' $6,800
10" $1,900 10-3/4" x 27.5 $7,500
11-/7/8 $4,500
TRICONE - carbide insert

3-7/8" $1,150
5" $1,629
5-1/2" $1,972 All unit prices are manufacturer
6" $2,131 list prices. Discounts or
6-1/4" $2,207 premiums may apply depending
6-3/4" $2,463 upon market conditions.
7-7/8" $3,023
9" $3,589
9-7/8" $4,787
11" $5,640
12-1/4" $6,603
15" $10,367
16" $11,016
L-18
EP 1110-1-8, Vol. 2
30 Apr 14
EP
Octpb
ROTARY BLASTHOLE
DRILLS
Bucyrus manufactures electric rotary blasthole drills with the most
innovative features on the market, including programmed drill control,
rack and pinion pull-down, hydrostatic propel drives and more. Contact
us today for more information about any of our performance-packed
drills!
59R
Max. hole size: 444 mm (17-1/2 in)
Max. bit loading: 74,830 kg (165,000 lbs)
Working weight: 183,673 kg (405,000 lbs)
49RIII
Max. hole size: 406 mm (16 in)
39HR
35HR Series
L-19
EP 1110-1-8, Vol. 2
30 Apr 14
EP
Octpb
Drilling Solutions
Blasthole Drills
Rotary
Large
Mid-range
Hydraulic Crawle
Pneumatic Crawl
DHD
Drill Selector
Waterwell Drills
Exploration Drills
Gas & Oil / Coal Bed
Drills
Drilling Accessories
Down Hole Drills
Threaded Access
Hollow Anchor Syst
Literature
Split Set Products
Aftermarket
Upgrades
Drilling Solutions Kits
Product Upgrad
Ingersoll-Rand has been in the drilling business since Simon Ingersoll invented his first Maintenance Up
rock drill in 1871. This innovative piece of machinery revolutionized the drilling industry Promotions
and set the pace for the company's future. Maintenance Sche
Service
New Product
Ingersoll-Rand drills are designed and manufactured to a stringent set of quality Events Calendar
standards, assuring you of the most efficient and reliable drills available anywhere. Authorized Distribut
Used Equipment
Now in our second century, we are proud of the comprehensive line of Ingersoll-Rand Federal Governmen
drilling equipment for the mining, exploration, oil and gas, quarry and water well industries Contact Us
around the world. Training Schedule
Copyright © 1996-2001 Ingersoll-Rand Company. All rights reserved.

Ingersoll-Rand Worldwide Headquarters
HOME BACK
200 Chestnut Ridge Road
Woodcliff Lake, NJ 07675 USA
L-20
EP 1110-1-8, Vol. 2
30 Apr 14
EP
Octpb
L-21
EP 1110-1-8, Vol. 2
30 Apr 14
EP
Octpb
Rotary - DM45/LP Drilling Solutions

Select Model: Blasthole Drills
The DM45/LP is a hydraulic rotary head
drive, multi-pass, crawler-mounted drill Rotary
T4BH rig with a 45,000 lb. (20,400 kg) bit load Large
DM25/SP capacity. The standard two-motor spur Mid-range
DM30 gear rotary head is rated from 9,000 ft-lb. Hydraulic Crawle
DM45/LP (12,204 N-m) at 0-100 RPM and 5,400 ft- Pneumatic Crawl
DM50/LP lb. (732 N-m) at 0-160 RPM. The DHD
DM-L/LP DM45/LP can drill from 5-1/8 to 7-7/8 in.
Drill Selector
DM45/SP (130 to 200 mm) diameter blastholes to
depths of 180 ft. (55 m) with a 30 ft. (9.1 Waterwell Drills
DM-LSP
m) drill pipe change. Two low-pressure Exploration Drills
DM-M2 Gas & Oil / Coal Bed
Ingersoll-Rand compressor options are
DM-M3 Drills
available with your choice of Caterpillar
DM-H2 or Cummins engines. Drilling Accessories
351 Down Hole Drills
Threaded Access
Hollow Anchor Syst
Literature
Split Set Products
Aftermarket
[ SPECS ] [ FEATURES ] [ LITERATURE ] Upgrades
Kits
Product Upgrad
Nominal Hole Diameter Maintenance Up
Diameter 6-8 in. Promotions
Power Pack Maintenance Sche
Engine #1 Cummins QSX15 (425 HP @ 1800 rpm) Service
900 @ 110 CFM @ PSI / 25.5 @ New Product
Compressor #1 758 m3/min@kPA Events Calendar
Engine #2 CAT C15 (425 HP @ 1800 RPM) Authorized Distribut
900 @ 110 CFM @ PSI / 25.5 @ Used Equipment
Compressor #2 758 m3/min@kPA Federal Governmen
Contact Us
Engine #3 Cummins QSX15 (475 HP @ 1800 RPM)
Training Schedule
1050 @ 110 CFM @ PSI / 29.7 @
Compressor #3 758 m3/min@kPA
Engine #4 Cat C15 (475 HP @ 1800 RPM)
1050 @ 110 CFM @ PSI / 29.7 @
Rotation
2-motor variable displacement, high
Type torque/high speed
Head Torque High torque: 9,000 ft-lb @ 100 rpm
Speed High speed: 5,400 ft-lb @ 160 rpm rpm
Feed System
Hydraulic cyls. w/cable pulldown & chain
Type pullback
Bit Load 45,000 lb / 20,411 kg
Tower
Pipe Length 30 ft. / 9.1 m.
4-member open front w/rectangular hollow
Fabrication steel tubing/double cut lacing
Undercarriage
Model Caterpillar 325L or equivalent
L-22
EP 1110-1-8, Vol. 2
30 Apr 14
EP
Octpb
Length 15.3 ft. / 4.66 m
Carousel
Capacity Capable of 180 ft.
Options
Contact your local IR distributor for a
Option #1 complete list of options.
Weight & Dimensions
Height (Tower Up) 43 ft. / 13.11 m
Approx. Working Weight 77,000 - 85,000 lbs. / 34,900 - 38,600 kg.
Material To Be Drilled
Soft Yes
Drill Application
Mining Yes
Quarry Yes
Drilling Method
Rotary Yes

HOME BACK
L-23
EP 1110-1-8, Vol. 2
30 Apr 14
EP
Octpb
Rotary - DM30 Drilling Solutions

The DM30 is a hydraulic tophead drive,
multi-pass, crawler-mounted drill rig Rotary
T4BH designed for blastholes ranging from 5- Large
DM25/SP 1/8 to 6-3/4 in. (130 to 171 mm) in Mid-range
DM30 diameter. On-board depth capability is Hydraulic Crawle
DM45/LP up to 150 ft. (45.7 m). For rotary Pneumatic Crawl
DM50/LP drilling, the DM30 can assert a bit load DHD
DM-L/LP force up to 30,000 lb. (13,608 kg) and
Drill Selector
DM45/SP rotation speeds of 0-130 RPM. This rig
can also be used with downhole drills Waterwell Drills
DM-LSP
when equipped with a high-pressure air Exploration Drills
compressor option.
DM-M3 Drills
DM-H2 Drilling Accessories
Threaded Access
Hollow Anchor Syst
Literature
Split Set Products
Aftermarket
Upgrades
Kits
Product Upgrad
[ SPECS ] [ FEATURES ] [ LITERATURE ] Maintenance Up
Promotions
Maintenance Sche
Nominal Hole Diameter
Service
Diameter 5-6 in.
New Product
Power Pack Events Calendar
Authorized Distribut
IR HR2 900/350 CFM @ PSI / Used Equipment
Compressor #1 25.5/2,413 m3/min@kPA
Federal Governmen
Engine #2 CAT C15 (525 HP @ 1800 RPM) Contact Us
IR HR2 900/350 CFM @ PSI / 25.5/2,413 Training Schedule
Compressor #2 m3/min@kPA
IR WW226 900/110 CFM @ PSI /
Compressor #3 25.5/758 m3/min@kPA
Engine #4 CAT C15 (425 HP @ 1800 RPM)
IR WW226 900/110 CFM @ PSI / 25.5/758
Isolates components from drilling and
Floating Sub Base propel shock loads/maintains alignment
Rotation
Type Rotary Tophead
Head Torque 5,400 ft-lb. / 7,322 N-m
Speed 0-100 rpm
Feed System
Type Single cylinder, cable feed
Bit Load 30,000 lb / (13,608) kg
Tower
4 member open front with hollow steel
Construction tubing.
L-24
EP 1110-1-8, Vol. 2
30 Apr 14
EP
Octpb
Undercarriage
Manufacturer Caterpillar
Options
Weight & Dimensions
Height (Tower Up) 44.3 ft. / 13.4 m
Approx. Working Weight 68,000 lbs. / 30,844 kg.
Hard Yes
Medium Yes
Soft Yes
Drill Application
Mining Yes
Quarry Yes
Drilling Method
Rotary Yes
DHD Yes

HOME BACK
L-25
EP 1110-1-8, Vol. 2
30 Apr 14
EP
Octpb
Rotary - DM25/SP Drilling Solutions

The DM25SP is a crawler-mounted rotary
table drill rig designed for single-pass Rotary
T4BH blasthole drilling to depths of up to 50 ft. Large
DM25/SP (15.2 m) and diameters of 3-1/2 to 6-3/4 Mid-range
DM30 in. (89 to 171 mm). This drill is capable of Hydraulic Crawle
DM45/LP rotary drilling with 25,000 lb. (11,340 kg) Pneumatic Crawl
DM50/LP of bit load at 0-200 rpm. The DM25SP DHD
DM-L/LP can also be used with downhole drills
Drill Selector
DM45/SP when equipped with a high-pressure air
compressor option. Waterwell Drills
DM-LSP
Exploration Drills
DM-M3 Drills
Threaded Access
Hollow Anchor Syst
Literature
Split Set Products
Aftermarket
Upgrades
Kits
Product Upgrad
Promotions
Maintenance Sche
Service
Diameter 5-6 in.
New Product
900/350 CFM @ PSI / 25.5/2,413 Used Equipment
Federal Governmen
900/350 CFM @ PSI / 25.5/2,413 Training Schedule
900/110 CFM @ PSI / 25.5/758
900/110 CFM @ PSI / 25.5/758
Rotation
Type Rotary Table Drive
Speed 0-170 rpm
Torque 3,500 / (4,746 N-m)
Feed System
Type Heavy-duty chains through cluster sprocket
Pulldown 25,000 lbs. / 11,340 kg.
Tower
4 main member, open front, rectangular
Construction steel tubing
#1 Single pass depth 40 ft. / 12.2 m.
Undercarriage
L-26
EP 1110-1-8, Vol. 2
30 Apr 14
EP
Octpb
Type Excavator
Options
Weight & Dimensions
Varies according to drill pipe: 60,000 -
Weight 62,000 lb / 27,216-28,123 kg
Hard Yes
Medium Yes
Soft Yes
Drill Application
Quarry Yes
Drilling Method
Rotary Yes
DHD Yes

HOME BACK
L-27
EP 1110-1-8, Vol. 2
30 Apr 14
EP
Octpb
Rotary - DM-M2 Drilling Solutions

Designed for rotary or downhole drilling of
up to 10-5/8 in. (270 mm) diameter Rotary
T4BH blastholes, the DM-M2 provides 75,000 Large
DM25/SP lb. (34,000 kg) of bit load and a 35 ft. (10 Mid-range
DM30 m) drill pipe change. Advanced frame and Hydraulic Crawle
DM45/LP tower design and a unique, patented Pneumatic Crawl
DM50/LP carriage feed system allow on-board drill DHD
DM-L/LP depths to 175 ft. (53 m).
Drill Selector
DM45/SP Compressor/engine packages in both low-
pressure, [1900 CFM @ 110 PSI (51 Waterwell Drills
DM-LSP
m3/min. @ 758 kPa)] for rotary drilling Exploration Drills
and high pressure [1250 CFM @ 350 PSI
DM-M3 Drills
(35.4 m3/min. @ 2,413 kPa)], for
DM-H2 downhole drilling, are available. Drilling Accessories
Threaded Access
Hollow Anchor Syst
Literature
Split Set Products
Aftermarket
Upgrades
Kits
Product Upgrad
[ SPECS ] [ FEATURES ] [ LITERATURE ]
Maintenance Up
Promotions
Nominal Hole Diameter Maintenance Sche
Diameter 9-11 in. Service
Power Pack New Product
Engine #1 Caterpillar 3412E / EPA certified Events Calendar
1900 @ 100 CFM @ PSI / 53.8 @ Authorized Distribut
Compressor #1 690 m3/min@kPA Used Equipment
Engine #2 Cummins QSK19 / EPA certified Federal Governmen
Contact Us
1900 @ 100 CFM @ PSI / 53.8 @
Compressor #2 690 m3/min@kPA Training Schedule
Engine #3 Caterpillar 3412E / EPA certified
1250 @ 350 CFM @ PSI / 35.4 @
Rotation
Type Two-motor, variable displacement
Speed Range 0-150 rpm, variable
Head Torque 0-8,640 ft-lbs (0-11,714 Nm) (forward)
Feed System
Type Patented carriage feed
Weight on Bit 0 to 75,000 lb. / 0 to 34,019 kg
Tower
Undercarriage
Model Caterpillar 330EL or equivalent
Carousel
Holds 2 to 4 drill pipe depending on pipe
Size diameter
L-28
EP 1110-1-8, Vol. 2
30 Apr 14
EP
Octpb
Options
Weight & Dimensions
Medium Yes
Soft Yes
Drill Application
Mining Yes
Drilling Method
Rotary Yes
DHD Yes

HOME BACK
L-29
EP 1110-1-8, Vol. 2
30 Apr 14
EP
Octpb
Rotary - T4BH Drilling Solutions

The T4BH is a truck-mounted,
hydraulic tophead drive multipass Rotary
T4BH rotary drill specificaly designed for Large
DM25/SP production blasthole drilling to depths Mid-range
DM30 of 150 ft. (45.7 m) with a 25 ft. (7.6 m) Hydraulic Crawle
DM45/LP drill pipe change. Nominal hole size is Pneumatic Crawl
DM50/LP 5-1/8 to 7-7/8 in. (130 to 200 mm) for DHD
DM-L/LP rotary or DHD drilling methods. Feed
Drill Selector
DM45/SP pressure generates a bit load force of
up to 30,000 lb. (12,610 kg). An angle Waterwell Drills
DM-LSP
drilling option is available. All drill Exploration Drills
functions are controlled from the newly
DM-M3 Drills
designed operator cab.
Threaded Access
Hollow Anchor Syst
Literature
Split Set Products
Aftermarket
Upgrades
Kits
Product Upgrad
Maintenance Up
Promotions
Maintenance Sche
Service
Nominal Hole Diameter New Product
Diameter 6-9 in. Events Calendar
Carrier Authorized Distribut
Chassis (Standard) Crane Carrier, Custom, 3 axle, 6X4 Used Equipment
Engine CAT C10 (305 HP) Federal Governmen
Power Pack Contact Us
Training Schedule
IR HR2-900/350 CFM @ PSI /
1050 @ 350 CFM @ PSI / 129.7 @
Engine #3 Cummins QSK-19C (700 HP @ 2100 RPM)
IR HR2.5 - 1250/350 CFM @ PSI / (35.39
Compressor #3 @ 2413) m3/min@kPA
Rotation
Type Rotary Tophead
Speed Range 0-160 RPM (std.)
Head Torque 6,500 ft-lb. / (8,814 N-m)
7,165 ft-lb @ 0-130 RPM / 9,716 N-m @ 0-
Option 130 RPM
Feed System
Type Hydraulic cylinders w/cable and chain
Pulldown 0-37,700 lbs. / 17,108 kg.
L-30
EP 1110-1-8, Vol. 2
30 Apr 14
EP
Octpb
Tower
4 member open front with ASTM A500 GRB
Construction steel tubing.
Cab & Controls
New cab designed to optimize operator
Operator Cab comfort and safety
All operational functions controlled from
Controls driller console in cab
Options
Contact your local distributor for a complete
Option #1 list of options.
Weight & Dimensions
Height (Tower Up) 28-3/4 ft. / 8.7 m
Hard Yes
Medium Yes
Soft Yes
Drill Application
Mining Yes
Quarry Yes
Drilling Method
Rotary Yes

HOME BACK
L-31
EP 1110-1-8, Vol. 2
30 Apr 14
EP
Octpb
DHD - DM-M2 Drilling Solutions

Designed for rotary or downhole drilling of
up to 10-5/8 in. (270 mm) diameter Rotary
CM695D blastholes, the DM-M2 provides 75,000 Large
DM25/SP lb. (34,000 kg) of bit load and a 35 ft. (10 Mid-range
DM30 m) drill pipe change. Advanced frame and Hydraulic Crawle
DM45/HP tower design and a unique, patented Pneumatic Crawl
DM45/SP carriage feed system allow on-board drill DHD
DM-L/HP depths to 175 ft. (53 m).
Drill Selector
DM-M2 Compressor/engine packages in both low-
pressure, [1900 CFM @ 110 PSI (51 Waterwell Drills
m3/min. @ 758 kPa)] for rotary drilling Exploration Drills
and high pressure [1250 CFM @ 350 PSI Gas & Oil / Coal Bed
(35.4 m3/min. @ 2,413 kPa)], for Drills
downhole drilling, are available. Drilling Accessories
Down Hole Drills
Threaded Access
Hollow Anchor Syst
Literature
Split Set Products
Aftermarket
Upgrades
Kits
Product Upgrad
Maintenance Up
Promotions
Nominal Hole Diameter Maintenance Sche
Diameter 9-11 in. Service
Power Pack New Product
Engine #1 Caterpillar 3412E / EPA certified Events Calendar
1900 @ 100 CFM @ PSI / 53.8 @ Authorized Distribut
Compressor #1 690 m3/min@kPA Used Equipment
Engine #2 Cummins QSK19 / EPA certified Federal Governmen
Contact Us
1900 @ 100 CFM @ PSI / 53.8 @
Compressor #2 690 m3/min@kPA Training Schedule
Engine #3 Caterpillar 3412E / EPA certified
1250 @ 350 CFM @ PSI / 35.4 @
Rotation
Type Two-motor, variable displacement
Speed Range 0-150 rpm, variable
Head Torque 0-8,640 ft-lbs (0-11,714 Nm) (forward)
Feed System
Type Patented carriage feed
Weight on Bit 0 to 75,000 lb. / 0 to 34,019 kg
Tower
Undercarriage
Model Caterpillar 330EL or equivalent
Carousel
Holds 2 to 4 drill pipe depending on pipe
Size diameter
L-32
EP 1110-1-8, Vol. 2
30 Apr 14
EP
Octpb
Options
Weight & Dimensions
Medium Yes
Soft Yes
Drill Application
Mining Yes
Drilling Method
Rotary Yes
DHD Yes

HOME BACK
L-33
EP 1110-1-8, Vol. 2
30 Apr 14
EP
Octpb
DHD - DM30 Drilling Solutions

The DM30 is a hydraulic tophead drive,
multi-pass, crawler-mounted drill rig Rotary
CM695D designed for blastholes ranging from 5- Large
DM25/SP 1/8 to 6-3/4 in. (130 to 171 mm) in Mid-range
DM30 diameter. On-board depth capability is Hydraulic Crawle
DM45/HP up to 150 ft. (45.7 m). For rotary Pneumatic Crawl
DM45/SP drilling, the DM30 can assert a bit load DHD
DM-L/HP force up to 30,000 lb. (13,608 kg) and
Drill Selector
DM-M2 rotation speeds of 0-130 RPM. This rig
can also be used with downhole drills Waterwell Drills
when equipped with a high-pressure air Exploration Drills
compressor option. Gas & Oil / Coal Bed
Drills
Down Hole Drills
Threaded Access
Hollow Anchor Syst
Literature
Split Set Products
Aftermarket
Upgrades
Kits
Product Upgrad
Promotions
Maintenance Sche
Service
Diameter 5-6 in.
New Product
IR HR2 900/350 CFM @ PSI / Used Equipment
Compressor #1 25.5/2,413 m3/min@kPA
Federal Governmen
IR HR2 900/350 CFM @ PSI / 25.5/2,413 Training Schedule
IR WW226 900/110 CFM @ PSI /
IR WW226 900/110 CFM @ PSI / 25.5/758
Rotation
Type Rotary Tophead
Head Torque 5,400 ft-lb. / 7,322 N-m
Speed 0-100 rpm
Feed System
Type Single cylinder, cable feed
Bit Load 30,000 lb / (13,608) kg
Tower
L-34
EP 1110-1-8, Vol. 2
30 Apr 14
EP
Octpb
Undercarriage
Manufacturer Caterpillar
Options
Weight & Dimensions
Hard Yes
Medium Yes
Soft Yes
Drill Application
Mining Yes
Quarry Yes
Drilling Method
Rotary Yes
DHD Yes

HOME BACK
L-35
EP 1110-1-8, Vol. 2
30 Apr 14
EP
Octpb
DHD - DM25/SP Drilling Solutions

The DM25SP is a crawler-mounted rotary
table drill rig designed for single-pass Rotary
CM695D blasthole drilling to depths of up to 50 ft. Large
DM25/SP (15.2 m) and diameters of 3-1/2 to 6-3/4 Mid-range
DM30 in. (89 to 171 mm). This drill is capable of Hydraulic Crawle
DM45/HP rotary drilling with 25,000 lb. (11,340 kg) Pneumatic Crawl
DM45/SP of bit load at 0-200 rpm. The DM25SP DHD
DM-L/HP can also be used with downhole drills
Drill Selector
DM-M2 when equipped with a high-pressure air
compressor option. Waterwell Drills
Exploration Drills
Drills
Down Hole Drills
Threaded Access
Hollow Anchor Syst
Literature
Split Set Products
Aftermarket
Upgrades
Kits
Product Upgrad
Promotions
Maintenance Sche
Service
Diameter 5-6 in.
New Product
900/350 CFM @ PSI / 25.5/2,413 Used Equipment
Federal Governmen
900/350 CFM @ PSI / 25.5/2,413 Training Schedule
900/110 CFM @ PSI / 25.5/758
900/110 CFM @ PSI / 25.5/758
Rotation
Type Rotary Table Drive
Speed 0-170 rpm
Torque 3,500 / (4,746 N-m)
Feed System
Type Heavy-duty chains through cluster sprocket
Pulldown 25,000 lbs. / 11,340 kg.
Tower
4 main member, open front, rectangular
Construction steel tubing
Undercarriage
L-36
EP 1110-1-8, Vol. 2
30 Apr 14
EP
Octpb
Type Excavator
Options
Weight & Dimensions
Varies according to drill pipe: 60,000 -
Weight 62,000 lb / 27,216-28,123 kg
Hard Yes
Medium Yes
Soft Yes
Drill Application
Quarry Yes
Drilling Method
Rotary Yes
DHD Yes

HOME BACK
L-37
EP 1110-1-8, Vol. 2
EP
30 Apr 14
Octpb
DHD - DM45/SP Drilling Solutions

The DM45/SP is a crawler-mounted
hydraulic rotary table drive, drill rig Rotary
CM695D designed to produce 50 ft. (15.2 m) of Large
DM25/SP clean hole in a single pass. Hole diameter Mid-range
DM30 capability is 5-1/2 to 6-3/4 in. (139.7 to Hydraulic Crawle
DM45/HP 171.5 mm) to a depth of up to 50 ft. (15.2 Pneumatic Crawl
DM45/SP m) with a downhole hammer (high- DHD
DM-L/HP pressure air package). Feed pressure
Drill Selector
DM-M2 generates a bit load force of up to 25,000
lb. (11,340 kg). An optional angle drilling Waterwell Drills
system is available. Exploration Drills
Drills
Down Hole Drills
Threaded Access
Hollow Anchor Syst
Literature
Split Set Products
Aftermarket
Upgrades
Kits
Product Upgrad
Maintenance Up
Promotions
[ SPECS ] [ FEATURES ] [ LITERATURE ] Maintenance Sche
Service
Nominal Hole Diameter New Product
Events Calendar
Diameter 5-7 in.
Power Pack
Used Equipment
Federal Governmen
900/350 CFM @ PSI / 25.5/2413
Compressor #1 Contact Us
m3/min@kPA
Training Schedule
900/350 CFM @ PSI / 25.5/2413
1070/350 CFM @ PSI / 30.30/2,413
1070/350 CFM @ PSI / 30.30/2413
Rotation
Type Rotary table w/kelly drive
Speed 0-200 rpm
Torque 4,000 ft-lb / (5,424 N-m)
Feed System
Type Chain and cable
Pulldown 25,000 lbs. / 11,340 kg.
Tower
Type Single Pass
4 member open front with rectangular steel
L-38
EP 1110-1-8, Vol. 2
EP 30 Apr 14
Octpb
Construction tubing
Undercarriage
Type Excavator-type
Options
Weight & Dimensions
Height (Tower Up) 76-1/2 ft. / 23.3 m
Hard Yes
Medium Yes
Drill Application
Mining Yes
Quarry Yes
Drilling Method
DHD Yes

HOME BACK
L-39
EP 1110-1-8, Vol. 2
EP
30 Apr 14
Octpb
Pneumatic Crawler - ECM350 Drilling Solutions

This agile, powerfull drill climbs
steep grades over roughest Rotary
LM100A ground, and takes the punishment. Large
CM348 You have seen thousands of them Mid-range
ECM350 on construction jobs of all kinds Hydraulic Crawle
around the world. The basic Pneumatic Crawl
ECM350 design has seen many DHD
improvements in its years of
Drill Selector
service ? but every drill produced
has set the world standard for Waterwell Drills
reliability and perfomance in its Exploration Drills
time. The ECM350 is also a fine Gas & Oil / Coal Bed
quarry drill when teamed with an Drills
Ingersoll-Rand air compressor. Drilling Accessories
This high-performance team gets Down Hole Drills
more work done faster, more Threaded Access
efficiently, and keeps doing it Hollow Anchor Syst
longer than anything else in its Literature
class. Split Set Products
Aftermarket
Upgrades
Kits
Nominal Hole Diameter Product Upgrad
Diameter 2-1/2 - 5-1/2 in. Maintenance Up
Promotions
Drifter
Maintenance Sche
Drifter #1 VL140
Service
Hole Diameter #1 2.5-4 " / 64-102 mm New Product
Rotation Speed #1 0 - 72 rpm Events Calendar
Frequency #1 2100 BPM Authorized Distribut
Air Consumption #1
750 SCFM @ 100 PSI / 21.2 m3/min @ 7 Used Equipment
kg/cm2 Federal Governmen
Stroke #1 5-1/2 in. / 140 mm. Contact Us
Bore #1 5-1/2 in. / 140 mm. Training Schedule
Weight #1 421 lb. / 191 kg.
Guide
Guide Dump #1 180 °
Guide Swing (L/R) 50 deg / 35 deg
Boom
Boom Swing (L/R) #1 40 ° / 35 °
Boom Lift (Up/Down) #1 45 ° / 15 °
Air Rotary Head
Weight 554 lb. / 252 kg.
1492 Nm @ 8.4 kg/cm? / (1100 lb-ft @ 120
Torque Max. PSI)
Rotation 0 - 72
120 CFM @ 50 RPM & 90 PSI / 3.4 m3/min
Air Consumption @ 50 RPM & 6.3 kg/cm2
Gear Ratio 33:1
2.23 kw @ 6.3 kg/cm? (3.0 hp @ 90 psig) /
Horse Power 3.13 kw @ 8.4 kg/cm? (4.2 hp @ 120 psig)
General
Feed/Pullback Force 3,000 lb / 1,361 kg
L-40
EP 1110-1-8, Vol. 2
EP 30 Apr 14
Octpb
Downhole Drills
O.D. #1 3.62 in. / 92 mm.
Length (bit ext.) #1 45.7 in. / 1161 mm.
Air Consumption @ 10.5 kg/cm? (150 5.1 m?/min / (180 SCFM)
PSIG) #1
PSIG) #1
Drill #2 DHD350R
Hole Diameter #2 5-1/8 - 5-1/2 in. / 130-140 mm.
Weight (less bit) #2 151 lb. / 68.5 kg.
O.D. #2 4.5 in. / 114 mm.
Length (bit ext.) #2 54.6 in. / 1388 mm.
PSIG) #2
PSIG) #2
Crawlair Drill Specifications
Net weight 12,900 lb. / 5851 kg.
Overall shipping length 12 ft. 0 in. / 3645 mm.
Width 8 ft 0 in. / 2438 mm.
Height (vertical guide) 18 ft. 10 in. / 5753 mm.
Steel change 12 ft. / 3645 mm.
Drill travel 14 ft. 3 in. / 4356 mm.
Max. horizontal boom swing 40? left, 35? right
Max. vertical boom movement 45? above, 15? below
Max. guide swing 50? left, 35? right
Max guide dump 180?
Ground clearance 12 in. / 292 mm.
Grouser width 10 in. / 254 mm.
Weight & Dimensions
Ground Clearance 12 " / 292 mm
Shipping Width 96 " / 2438 mm
Shipping Length 144 " / 3645 mm
Approx. Working Weight 12,900 lbs. / 5851 kg.
Hard Yes
Medium Yes
Soft Yes
Drill Application
Mining Yes
Construction Yes
Quarry Yes
Drilling Method
Drifter Yes

HOME BACK
L-41
EP 1110-1-8, Vol. 2
EP
30 Apr 14
Octpb
Hydraulic Crawler - ECM-720 Drilling Solutions

They said it couldn't be done...they were
wrong. The new ECM-720 crawler drill Rotary
ECM470 delivers a perfect balance of productivity Large
ECM580 and cost efficiency. Hole straightness, Mid-range
ECM590 faster penetration rates, long accessory Hydraulic Crawle
ECM660II life, and increased profitability are just a Pneumatic Crawl
ECM-720 few of the results you can expect with the DHD
ECM-720.
Drill Selector
Waterwell Drills
Exploration Drills
Drills
Down Hole Drills
Threaded Access
Hollow Anchor Syst
[ SPECS ] [ FEATURES ] [ LITERATURE ] Literature
Split Set Products
Aftermarket
Nominal Hole Diameter Upgrades
Diameter 4-1/2 - 5-1/2 in. Kits
Drifter Product Upgrad
Type Montabert HC-200A Maintenance Up
Boom & Guide Promotions
Boom Swing 45 deg right / 20 deg left maximum Maintenance Sche
Vertical Boom Movement 50 deg up / 20 deg down maximum Service
New Product
Guide Swing 20 deg right / 90 deg left maximum
Events Calendar
Guide Dump 135 deg maximum
Boom Extension 36 in. / 914 mm
Used Equipment
Guide Extension 5 ft / 1,524 mm Federal Governmen
Overall Guide Length 27 ft 6 in / 8.4 m Contact Us
Drifter Travel 16 ft. 11 in. / 5.15 m Training Schedule
Engine
Type CAT 3176 C-10
Rated Power 365 HP / 272 kW
Operating Speed 1,800 rpm
Compressor
Type Ingersoll-Rand Rotary Screw
Volume 480 CFM / 13.6 m3/min
Pressure 150 PSI / 10.3 BAR
Cab & Controls
Operator Cab ROPS/FOPS
Noise level 80 dBA
General
Gradeability 35 deg (70 percent) °
Tramming Speed 2.0 mph / 3.3 km/hr
Ground clearance 17 in. / 432 mm.
Grouser Width 13-3/4 in. / 349 mm mm.
Rod Changer Capacity (6) 12 ft (3.66 m) / (6) 14 ft (4.27 m) opt.
Shipping Information
Weight 45,900 lb / 20,820 kg
L-42
EP 1110-1-8, Vol. 2
EP 30 Apr 14
Octpb
Width 8 ft 3 in / 2.5 m
Length 35 ft 8 in / 10.9 m
Height 10 ft 8 in / 3.3 m
Hard Yes
Medium Yes
Soft Yes
Drill Application
Mining Yes
Construction Yes
Quarry Yes
Drilling Method
Drifter Yes

HOME BACK
L-43
EP 1110-1-8, Vol. 2
EP
30 Apr 14
Octpb
Hydraulic Crawler - ECM590 Drilling Solutions

The ECM-590 is a self-contained, cabless
hydraulic crawler drill capable of drilling Rotary
ECM470 up to 4 in. (102 mm) holes. It is available Large
ECM580 in either a YH70 drifter and rod rack Mid-range
ECM590 configuration for smaller hole work, or Hydraulic Crawle
ECM660II with a YH80 and rod changer for higher Pneumatic Crawl
ECM-720 production requirements. An extended DHD
guide option for 20 ft. (6.1 m) starter steel
Drill Selector
is available.
Waterwell Drills
Exploration Drills
Drills
Down Hole Drills
Threaded Access
Hollow Anchor Syst
Literature
Split Set Products
Aftermarket
Upgrades
[ SPECS ] [ FEATURES ] [ LITERATURE ] Kits
Product Upgrad
Maintenance Up
Promotions
Diameter 2-1/2 - 4-1/2 in.
Maintenance Sche
Drifter Service
Drifter #1 YH70 New Product
Hole Diameter #1 2.5-4 " / 64-102 mm Events Calendar
Rotation Speed #1 0-200 rpm Authorized Distribut
Frequency #1 2800 BPM Used Equipment
Weight #1 419 lb. / 190 kg. Federal Governmen
Steel Size #1 T45/T38 Contact Us
Drifter #2 YH80A Training Schedule
Hole Diameter #2 2.5-4.5 in. / 64-114 mm.
Rotation Speed #2 0-200 rpm
Frequency #2 2600 BPM
Weight #2 462 lb. / 210 kg.
Steel Size #2 T51/T45
Hydraulic Pressure 2130 psi / 150 kg/cm?
Boom & Guide
Horizontal Boom Swing 30 deg R / 34.6 deg L
Vertical Boom Movement 51 deg up / 15 deg down
Guide Swing 48 deg R / 40 deg L
Guide Dump 180 deg
Boom Extension - YH70 (YH80A) 48 in (30 in) / 1,219 mm (762 mm)
Drifter Travel - YH70 (YH80A) 15 ft 4 in (14 ft) / 3,099 mm (4,267 mm)
Guide Extension 4 ft / 1,219 mm
Overall Guide Length 23 ft 8 in / 7,214 mm
Engine
Type Cummins 6CT8.3
Rated Power 215 HP / 159 kW
Operating Speed 2350 rpm
L-44
EP 1110-1-8, Vol. 2
EP 30 Apr 14
Octpb
IR Rotary Screw Compressor

Compressor pressure(max) 140 psig / 9.8 kg/cm2
Compressor volume 250 cfm / 7 m?/min
General
Gradeability 35 °
Tramming Speed 2 mph / 3.3 km/hr
Grouser Width 12 in. / 305 mm.
Steel length starter rod 14 ft. / 4.27 m.
Weight & Dimensions
Length 232.9 " / 5918 mm
Weight #2 24,500 lb. / 11,150 kg.
Shipping Width 95.98 " / 2438 mm
Shipping Height 112 " / 2845 mm
Hard Yes
Medium Yes
Soft Yes
Drill Application
Construction Yes
Drilling Method
Drifter Yes

HOME BACK
L-45
EP 1110-1-8, Vol. 2
EP
30 Apr 14
Octpb
Pneumatic Crawler - LM100A Drilling Solutions

The LM100A is a small class
pneumatic Crawlair?, capable of Rotary
LM100A drilling 1-3/4" to 4- 1/2" (44 - 114 mm) Large
CM348 diameter holes. It can be equipped Mid-range
ECM350 with either of two drifters or a BRH Hydraulic Crawle
rotary head for downhole drilling. The Pneumatic Crawl
LM100A is ideal for applications in DHD
confined areas where hand-held tools
Drill Selector
are not enough, and is light enough to
transport by helicopter. Like all Waterwell Drills
Ingersoll-Rand crawler drills, the Exploration Drills
LM100A is "Abuse Resistant". It keeps Gas & Oil / Coal Bed
coming back for more! Drills
Down Hole Drills
Threaded Access
Hollow Anchor Syst
Literature
Split Set Products
Aftermarket
Upgrades
Kits
Product Upgrad
Nominal Hole Diameter Maintenance Up
Diameter 1-3/4 - 2-1/2 in. Promotions
Maintenance Sche
Carrier
Service
Overall Track Length 72 " / 1845 mm
New Product
Events Calendar
Oscillation 20 ° Authorized Distribut
Air Motors 4.5 HP Used Equipment
Gradeability 30 ° Federal Governmen
Tramming Speed 0-2 mph / 0-3.2 km/hr Contact Us
Drifter Training Schedule
Type Ingersoll-Rand YD90
Hole Diameter #1 1.75-2.5 " / 44-64 mm
375 scfm @ 100 psi & 50 rpm / 10.6 m3/min
Air Consumption #1 @ 7 kg/cm2 & 50 rpm
Stroke #1 3.4 in. / 85 mm.
Bore #1 3.5 in. / 90 mm.
Steel Size #1 10 ft / 3048 mm
Drifter #2 VL120
Hole Diameter #2 2 - 3.5 in. / 51 - 89 mm.
600 SCFM @ 50 RPM & 100 psi / 17.0
Air Consumption #2 m3/min @ 50 RPM & 7 kg/cm2
Stroke #2 3.62 in. / 92 mm.
Bore #2 4.75 in. / 120 mm.
Steel Size #2 10 ft / 3048 mm
Guide
Guide Dump #1 75 °
Guide Swing (L/R) 45 deg/45 deg
L-46
EP 1110-1-8, Vol. 2
EP 30 Apr 14
Octpb
Guide Extension #1 29 " / 750 mm

Drill Rod Length 10 ft. / 3 m
Feed Motor Pull 3000 lbs. / 1360 kg.
Boom
Boom Swing (L/R) #1 30/35 °
Boom Lift (Up/Down) #1 45/30 °
Coverage Length 107 " / 2720 mm
Max. Drill Height (Horizontal) 99 " / 2510 mm
BRH Rotary Head
Weight 304 lbs. / 138 kg.
Torque Maximum 700 lb.-ft. / 96.7 kg.-m
Rotation Range 0 - 50 RPM
120 SCFM @ 50 RPM & 100 psi / 3.39
Air Consumption m3/min @ 50 RPM & 7 kg/cm2
Gear Ratio 20:1
Horse Power @ 100 psi (7 kg/cm) 4.5 HP / 3.35 kW
Weight & Dimensions
Width 75 " / 1905 mm
Length (Boom @45°) 195 " / 4950 mm
Minimum Height 44 " / 1120 mm
Height (Boom @45°) 188 " / 4775 mm
Hole Size 1.75-4.5 " / 44-114 mm
Weight Less Drifter 5400 lbs. / 2450 kg.
Hard Yes
Medium Yes
Soft Yes
Drill Application
Mining Yes
Construction Yes
Quarry Yes
Drilling Method
Drifter Yes

HOME BACK
L-47
EP 1110-1-8, Vol. 2
30 Apr 14
L-48
EP 1110-1-8, Vol. 2
30 Apr 14
GLOSSARY
TERMS AND ABBREVIATIONS
AVF average value factor

bhp brake horsepower
CAT category
CENWW U.S. Army Corps of Engineers, Walla Walla District
CMR cost of money rate
cwt hundredweight
D diesel
DC discount code
DEPR depreciation
DT drive tire
E electricity
EAF economic adjustment factor
EK economic key
EP Engineer Pamphlet
ER Engineer Regulation
FAR Federal Acquisition Regulation
EFAR Engineer Federal Acquisition Regulation
FCCM facilities capital cost of money
FOG filters, oil, and grease
FT front tire
G gas
G&A general and administrative
gal gallon
GCW gross combined weight
GVW gross vehicle weight
hp horsepower
HPF horsepower factor
hr hour
ID No. identification number
IGE Independent Government Estimate
kW kilowatt
LAF labor adjustment factor
lbs pounds
LIFE Chapter 1 economic life (probably should take this out)
N number of years
PDF portable document format
PTO power take off
RCF repair cost factor
RF repair factor
ROPS rollover protective structures
RPR repairs
Glossary-1
EP 1110-1-8, Vol. 2
30 Apr 14
SLV salvage value
SUB subcategory
TCI tire cost index
TEV total equipment value
TT trailing tire
USACE United States Army Corps of Engineers
WHPY working hours per year
wk week
WLS water, lube, and supplies
yr year
Glossary-2
EP 1110-1-8, Vol. 2
30 Apr 14
EQUIPMENT INDEX
CAT DESCRIPTION PAGE
A10 AGGREGATE / CHIP SPREADERS ................................................................................................. 2-21
A15 AIR COMPRESSORS, PORTABLE .................................................................................................. 2-22
A20 AIR HOSE, TOOLS & EQUIPMENT ................................................................................................. 2-26
A25 ASPHALT PAVING DISTRIBUTORS................................................................................................ 2-29
A30 ASPHALT PAVERS & MISCELLANEOUS ROAD EQUIPMENT ....................................................... 2-30
A35 ASPHALT PAVING KETTLES .......................................................................................................... 2-34
A40 ASPHALT & CONCRETE MILLERS / PROFILERS / PLANERS / ROTARY GRINDERS................... 2-35
A45 ASPHALT RECYCLERS & SEALERS .............................................................................................. 2-36
B10 BATCH PLANTS, ASPHALT & CONCRETE..................................................................................... 2-37
B15 BROOMS, STREET SWEEPERS & FLUSHERS .............................................................................. 2-44
B20 BRUSH CHIPPERS.......................................................................................................................... 2-46
B25 BUCKETS, CLAMSHELL ................................................................................................................. 2-47
B30 BUCKETS, CONCRETE................................................................................................................... 2-50
B35 BUCKETS, DRAGLINE .................................................................................................................... 2-52
C05 CHAIN SAWS .................................................................................................................................. 2-59
C10 COMPACTORS, WALK-BEHIND OR REMOTE CONTROLLER....................................................... 2-59
C15 CONCRETE CLEANERS / ABRASIVE BLASTERS .......................................................................... 2-62
C20 CONCRETE BUGGIES .................................................................................................................... 2-63
C25 CONCRETE FINISHERS/SCREEDS/SPREADERS ......................................................................... 2-64
C35 CONCRETE GUNITERS / SHOTCRETERS..................................................................................... 2-66
C40 CONCRETE MIXING UNITS ............................................................................................................ 2-68
C45 CONCRETE PAVING MACHINES ................................................................................................... 2-70
C55 CONCRETE PUMPS ....................................................................................................................... 2-72
Index-1
EP 1110-1-8, Vol. 2
30 Apr 14
C60 CONCRETE SAWS (Add cost for sawblade wear) ............................................................................ 2-74
C65 CONCRETE VIBRATORS................................................................................................................ 2-76
C75 CRANES, HYDRAULIC, SELF-PROPELLED ................................................................................... 2-77
C80 CRANES, HYDRAULIC, TRUCK MOUNTED ................................................................................... 2-79
C85 CRANES, MECHANICAL, LATTICE BOOM, CRAWLER MOUNTED ............................................... 2-82
C90 CRANES, MECHANICAL, LATTICE BOOM, TRUCK MOUNTED ..................................................... 2-86
C95 CRANES, TOWER ........................................................................................................................... 2-86
D10 DRILLS, HYDRAULIC TRACK (Add cost for drill steel and bit wear) ................................................. 2-90
D15 DRILLS, HORIZONTAL .................................................................................................................... 2-91
D20 DRILLS, CORE, COLUMN MOUNTED (Add cost for drill steel and bit wear) .................................... 2-94
D25 DRILLS, CORE & DOWELLING (Add cost for drill steel and bit wear) ............................................... 2-95
D30 DRILLS, EARTH / AUGER (Add cost for drill steel and cutting edge wear)........................................ 2-96
D35 DRILLS, ROTARY BLASTHOLE (Add cost for drill steel and bit wear) .............................................. 2-98
F10 FORK LIFTS................................................................................................................................... 2-100
G10 GENERATOR SETS ...................................................................................................................... 2-100
G15 GRADERS, MOTOR ...................................................................................................................... 2-102
H10 HAMMERS, HYDRAULIC (Demolition tool) (Add cost for point wear) ............................................. 2-103
H13 HAZARDOUS/TOXIC WASTE EQUIPMENT .................................................................................. 2-105
H20 HOISTS & AIR WINCHES .............................................................................................................. 2-119
H25 HYDRAULIC EXCAVATORS, CRAWLER MOUNTED.................................................................... 2-120
H30 HYDRAULIC EXCAVATORS, WHEEL MOUNTED......................................................................... 2-134
H35 HYDRAULIC SHOVELS, CRAWLER MOUNTED ........................................................................... 2-135
L10 LAND CLEARING EQUIPMENT ..................................................................................................... 2-136
L15 LANDSCAPING EQUIPMENT ........................................................................................................ 2-138
L20 LIGHTING SETS, TRAILER MOUNTED ......................................................................................... 2-140
L25 LINE STRIPING EQUIPMENT ........................................................................................................ 2-141
Index-2
EP 1110-1-8, Vol. 2
30 Apr 14
L30 LOADERS, BELT (Conveyor belts) & ACCESSORIES .................................................................... 2-142
L35 LOADERS, FRONT END, CRAWLER TYPE................................................................................... 2-144
L40 LOADERS, FRONT END, WHEEL TYPE........................................................................................ 2-144
L50 LOADERS / BACKHOE, WHEEL TYPE .......................................................................................... 2-148
L55 LOADER / BACKHOE, ATTACHMENTS......................................................................................... 2-149
L60 LOG SKIDDERS............................................................................................................................. 2-150
M10 MARINE EQUIPMENT (NON DREDGING) .................................................................................... 2-151
P10 PILE HAMMER ACCESSORIES - EXTRACTORS & BOX LEADS.................................................. 2-156
P20 PILE HAMMERS, DOUBLE ACTING .............................................................................................. 2-156
P25 PILE HAMMERS, SINGLE ACTING ............................................................................................... 2-158
P30 PILE HAMMERS, DRIVER/ EXTRACTOR, VIBRATORY ................................................................ 2-161
P35 PIPELAYERS ................................................................................................................................. 2-161
P40 PLATFORMS & MAN-LIFTS........................................................................................................... 2-162
P45 PUMPS, GROUT............................................................................................................................ 2-163
P50 PUMPS, WATER, CENTRIFUGAL, TRASH ................................................................................... 2-166
P55 PUMPS, WATER, SUBMERSIBLE ................................................................................................. 2-168
P60 PUMPS, WATER, CENTRIFUGAL, DEWATERING........................................................................ 2-169
P65 PUMPS, WATER, DIAPHRAGM..................................................................................................... 2-171
P70 PUMPS, WATER (For core drills) ................................................................................................... 2-172
R10 RIPPERS & HYDRAULIC BANK SLOPERS (Add cost for point wear) ............................................ 2-172
R15 ROLLERS, STATIC, TOWED, PNEUMATIC................................................................................... 2-175
R20 ROLLERS, STATIC, TOWED, STEEL DRUM................................................................................. 2-175
R30 ROLLERS, STATIC, SELF-PROPELLED ....................................................................................... 2-176
R40 ROLLERS, VIBRATORY, TOWED ................................................................................................. 2-179
R45 ROLLERS, VIBRATORY, SELF-PROPELLED, DOUBLE DRUM .................................................... 2-179
R50 ROLLERS, VIBRATORY, SELF-PROPELLED, SINGLE DRUM ..................................................... 2-181
Index-3
EP 1110-1-8, Vol. 2
30 Apr 14
R55 ROOFING EQUIPMENT ................................................................................................................ 2-185
S10 SCRAPERS, ELEVATING .............................................................................................................. 2-187
S15 SCRAPERS, CONVENTIONAL ...................................................................................................... 2-187
S20 SCRAPERS, TANDEM POWERED ................................................................................................ 2-188
S25 SCRAPERS, TRACTOR DRAWN................................................................................................... 2-189
S30 SCREENING & CRUSHING PLANTS............................................................................................. 2-190
S35 SNOW REMOVAL EQUIPMENT .................................................................................................... 2-204
S40 SOIL & ROAD STABILIZERS ......................................................................................................... 2-204
S45 SPLITTERS, ROCK & CONCRETE ................................................................................................ 2-205
T10 TRACTOR BLADES & ATTACHMENTS (including agricultural) ...................................................... 2-206
T15 TRACTORS, CRAWLER (DOZER) (includes blade) ....................................................................... 2-209
T20 TRACTORS, WHEEL TYPE (DOZER) ............................................................................................ 2-212
T25 TRACTORS, AGRICULTURAL ....................................................................................................... 2-213
T30 TRENCHERS, CHAIN TYPE CUTTER ........................................................................................... 2-214
T35 TRENCHERS, WHEEL TYPE CUTTER.......................................................................................... 2-217
T40 TRUCK OPTIONS .......................................................................................................................... 2-218
T45 TRUCK TRAILERS......................................................................................................................... 2-222
T50 TRUCKS, HIGHWAY (Add attachments as required) ...................................................................... 2-227
T55 TRUCKS, OFF-HIGHWAY.............................................................................................................. 2-231
T56 TRUCKS,OFF-HIGHWAY/PRIME MOVER TRACTORS & WAGONS ............................................. 2-234
T57 TRUCKS, VACUUM ....................................................................................................................... 2-234
T60 TRUCKS, WATER, OFF-HIGHWAY ............................................................................................... 2-235
T65 TUNNEL/MINING EQUIPMENT...................................................................................................... 2-236
W25 WATER & CO2 BLASTERS .......................................................................................................... 2-236
W30 WATER TANKS ............................................................................................................................ 2-241
W35 WELDERS .................................................................................................................................... 2-241
Index-4

EP 1110 1 8 - Vol - 02

Uploaded by

Copyright:

Available Formats

EP 1110 1 8 - Vol - 02

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

EP 1110 1 8 - Vol - 02

Uploaded by

Copyright:

Available Formats

EP 1110-1-8

Engineering and Design

1. Purpose. This pamphlet is authorized by and established in accordance with Federal

2. Applicability. This pamphlet applies to all USAGE commands. It is applicable to all

3. Distribution Statement. Approved for public release, distribution is unlimited.

4. References. See Appendix A.

FOR THE COMMANDER:

This pamphlet supersedes EP 1110-1-8, dated 30 November 2011.

[This page intentionally left blank]

Engineering and Design

Use 1.1 1-1

Chapter 2. Methodology for Construction Equipment

Contents 2.1 2-1

Facilities Capital Cost of Money (FCCM) 2.21 2-6

Chapter 3. Adjustments to Hourly Rates

Contents 3.1 3-1

Chapter 4. Methodology for Dredging Plant and Marine Equipment

Contents 4.1 4-1

Prime and Secondary Power 4.12 4-5

Appendix A - References A-1

[This page intentionally left blank]

(1) Cost or pricing data is not required, as defined in Federal Acquisition

1.4 How to Obtain Assistance. When assistance is needed in understanding the

1.5 How to Obtain CHECKRATE. A Microsoft Excel® workbook, named

Land Based Equipment Marine equipment

Use the methodology found in Chapter 4 for determining

Calculate a rate based on the step-by-step

The contractor shall be required to furnish copies of all YES

If the contractor is able to furnish the above information, NO

YES If fuel costs are adjusted FOG costs also need to be

If equipment is older than in Table 2-1 determine economic

Adjust the rate using

Methodology for Construction Equipment

a. Ownership Cost Elements. The ownership portion of the rate consists of an

b. Operating Cost Elements. Operating costs include allowances for the

(2) Filters, oil, and grease (FOG) (includes servicing).

(3) Repairs (includes maintenance and major overhauls).

(4) Tire wear (replacement).

(5) Tire repair.

(1) Operating labor.

(2) Mobilization and demobilization.

(3) Field office overhead expenses.

(4) Home office or general and administrative (G&A) overhead expenses.

(5) Investment tax credit.

(6) Contingency allowance.

(8) Parts and labor escalation.

(2) Jobsite security, inspection fees, recordkeeping, mechanic training, and

SECTION II. OPERATING CONDITIONS

2.4 Average, Difficult, or Severe Conditions. Operating conditions may be average,

2.5 Determination of Condition. For contract modifications, the contracting officer

appendix C will be consistent with examples shown in appendix C. The operating

SECTION III. EQUIPMENT SELECTION

2.6 General. Equipment shown in table 2-1 is representative of equipment that is

2.7 Truck Selection. Because of the large number of possible combinations of

2.9 Equipment Accessories. Equipment accessories included on the major pieces of

SECTION IV. EQUIPMENT VALUE

c. Equipment maintenance and repairs.

d. Mobilization and demobilization.

SECTION VI. SALVAGE VALUE