Inspection & Testing Requirements Scope:: Test and Inspection Per
Inspection & Testing Requirements Scope:: Test and Inspection Per
Inspection & Testing Requirements Scope:: Test and Inspection Per
TEST AND INSPECTION PER: 04-SAMSS-055, ISO 10423 nd Specifications As Noted Below.
0020 R Drawing Approval and valve data sheet Verify Company approval.
0040 R NDT Personnel and Procedure Reviews verify valid personnel qualification and approved procedures.
0052 R X Welders Qualification Records Shall be qualified per ASME section IX or equivalent.
Performance records shall show acceptable rejection rate level.
0054 R Welding Inspector Qualification Shall be certified to AWS (CWI) or CSWIP3.1 or equivalent.
0056 R NDT Technician Qualification Shall be certified to ASNT Level- I or equivalent as per refer
SAEP 1142-Appendix-01
0058 R NDT Inspector Qualification Shall be certified to ASNT Level- II or equivalent as per refer
SAEP 1142-Appendix-01
0070 R Material requirement Per ISO 10423 Table 3 (Notes 3 and 4). Compliance to NACE
MR0175/ISO15156. Per SA-175 form code # 043000
0020
0010
*** R
In process inspection & test requirement
PWHT
Specification Details / Notes:
Per ISO 10423 PSL specified (Note 3)
0040 R X Tensile test and Impact test Per ISO 10423 PSL specified (Note 3)
IR045600 Continued...
INSPECTION & TESTING REQUIREMENTS REVISION: 07/12/2017 CODE NUMBER: PAGE:
SAUDI ARAMCO FORM-175 REPLACES: 10/31/2016 IR045600 2 of 3
(1).VISUAL INSPECTION BY BUYER INSPECTION REPRESENTATIVE
(2) REVIEW AND VERIFICATION OF MATERIAL CERTIFICATES AND INSPECTION RECORDS
(3) SUBMISSION OF MANUFACTURING, INSPECTION AND QUALITY RECORDS
0050 X Serialization & Traceability Per ISO 10423 PSL specified (Note 3)
0060 R X Hardness Tests 04-SAMSS-055 ISO 10423: Hardness testing locations and
frequency shall be by the Vickers 1 - 10-kg method only for
evaluation of hard facing and overlay procedure
0090 R b) Liquid Penetrant Testing (LP) & Magnetic Particle (MT) 04-SAMSS-055. Fluorescent Methods
0120 H R X Weld Inspection (NDE) : Visual, Surface NDE, Repair welding and Per 04-SAMSS-055 & ISO 10423 PSL specified (Note 3)
volumetric NDE
0030
0010
***
H R X
Final inspection & test requirements
Pressure Testing; Hydro, Pneumatic
Specification Details / Notes:
Per 04-SAMSS-055 and ISO 10423 PSL specified(Note 3)
0020 H R X Gas Testing (As applicable) Per 04-SAMSS-055 and ISO 10423 PSL specified (Note 3)
0030 H X Visual and Dimensional Inspection ISO 10423 PSL specified (Note 3)
0040 W Assembled Equipment Inspections ISO 10423 PSL specified (Note 3): Assembly serialization,
traceability records.
0060 H Functional Tests 04-SAMSS-055 and ISO 10423 PSL specified (Note 3)
IR045600 Continued...
INSPECTION & TESTING REQUIREMENTS REVISION: 07/12/2017 CODE NUMBER: PAGE:
SAUDI ARAMCO FORM-175 REPLACES: 10/31/2016 IR045600 3 of 3
(1).VISUAL INSPECTION BY BUYER INSPECTION REPRESENTATIVE
(2) REVIEW AND VERIFICATION OF MATERIAL CERTIFICATES AND INSPECTION RECORDS
(3) SUBMISSION OF MANUFACTURING, INSPECTION AND QUALITY RECORDS
0070 H Draining after Testing, Sealing, Surface Protection, Rust Per 04-SAMSS-055, ISO 10423, and PO specification.
Prevention.
0080 H Marking and Preparation for Shipping Per 04-SAMSS-055, ISO 10423, and PO specification.
Notes:
(1)Refer detailed instruction sheet SA175 form IR000003 of inspection requirement for ideal use of this form.
(2) Excludes valves classified under SAMSS class 34 & SAMSS class 45.
(3) Must meet the PSL requirements and additional requirement in 04-SAMSS-055 as a minimum. See PO specification for any additional
requirements
(4) Wrought product shall be used for PSL 3, 3G and 4 in accordance with ISO 10423.
End of IR045600