Nothing Special   »   [go: up one dir, main page]
Scribd Logo
Upload

Welcome to Scribd!

  • 32 views

    303-14 Electronic Engine Controls - Removal and Installation - Catalyst Monitor Sensor

    Uploaded by

    CARLOS LIMADA

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    303-14 Electronic Engine Controls - Removal and Installation - Catalyst Monitor Sensor

    Uploaded by

    CARLOS LIMADA
    32 views4 pages

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    32 views4 pages

    303-14 Electronic Engine Controls - Removal and Installation - Catalyst Monitor Sensor

    Uploaded by

    CARLOS LIMADA

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    Page 1 of 4

    303-14 Electronic Engine Controls - 2.3L EcoBoost (201kW/273PS) 2019 Ranger


    Removal and Installation Procedure revision date: 10/30/2018

    Catalyst Monitor Sensor

    Base Part Number: 9G444

    Special Tool(s) / General Equipment

    303-476 (T94P-9472-A)
    Socket, Exhaust Gas Oxygen Sensor
    TKIT-1994-LM/M
    TKIT-1994-F
    TKIT-1994-FLM/FM

    Materials

    Name Specification
    Motorcraft® High Temperature Nickel Anti-Seize Lubricant -
    XL-2
    Motorcraft® Penetrating and Lock Lubricant -
    XL-1
    Removal

    NOTE: Removal steps in this procedure may contain installation details.

    1. With the vehicle in NEUTRAL, position it on a hoist.


    Refer to: Jacking and Lifting (100-02 Jacking and Lifting, Description and Operation).

    2. Remove the RH front wheel and tire.


    Refer to: Wheel and Tire (204-04A Wheels and Tires, Removal and Installation).

    3. Remove the retainers and the RH side splash shield.

    http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
    Page 2 of 4

    4. Disconnect the electrical connector and harness retainers. Apply penetrating oil to sensor, using the
    special tool remove the Catalyst monitor sensor.
    Use Suggested Tool: 303-476 (T94P-9472-A) Socket, Exhaust Gas Oxygen Sensor. Tool shown or a
    commercially available equivalent can be used.
    Material: Motorcraft® Penetrating and Lock Lubricant / XL-1

    http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
    Page 3 of 4

    Installation

    1. To install, reverse the removal procedure.

    2. Apply anti-seize to thread of sensor, using the special tool install the Catalyst monitor sensor. Connect the
    electrical connector and harness retainers.
    Use Special Service Tool: 303-476 (T94P-9472-A) Socket, Exhaust Gas Oxygen Sensor.
    Material: Motorcraft® High Temperature Nickel Anti-Seize Lubricant / XL-2
    Torque: 35 lb.ft (48 Nm)

    http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019
    Page 4 of 4

    Copyright © 2019 Ford Motor Company

    http://www.fordservicecontent.com/Ford_Content/vdirsnet/workshop/ody/~WSKG/US/EN/... 1/9/2019

    You might also like