Frigidaire Fad954dwd 95 Pint Dehumidifier Owners Manual
Frigidaire Fad954dwd 95 Pint Dehumidifier Owners Manual
Frigidaire Fad954dwd 95 Pint Dehumidifier Owners Manual
TA B L E O F C O N T E N T S
Important Safety Instructions ............................... 2 Care And Cleaning .............................................. 9
Installation........................................................... 3 Storage ............................................................. 9
Location .............................................................. 3 Before You Call ................................................... 10
How It Works....................................................... 3 Major Appliance Limited Warranty ........................ 11
Operating Instructions .......................................... 4-8
NOTE:
This USE & CARE MANUAL provides specific operating instructions for your model. Use the dehumidifier only as instructed in this USE & CARE
MANUAL. These instructions are not meant to cover every possible condition and situation that may occur. Common sense and caution must be
practiced when installing, operating, and maintaining any appliance.
WARNING WARNING
Avoid fire hazard or electric shock. Do not For Your Safety
use an extension cord or an adaptor plug. Do Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or
not remove any prong from the power cord. any other appliance. Read product labels for flammability and other warnings.
Discard water from bucket. Water is not potable and cannot be used for drinking.
Grounding type wall
receptacle
WARNING
Do not, under any
Child Safety Precautions
circumstances, cut,
Destroy the carton, plastic bags, and any packing materials immediately after the
remove, or bypass the
dehumidifier is unpacked. Children should never use these items for play.
grounding prong.
Do not leave children unattended in an area where the appliance is operating.
Do not allow them to sit or stand on the appliance.
WARNING
Electrical Information
Power supply cord For your safety and protection, this dehumidifier is equipped with a three-prong grounding
with 3-prong grounding plug on the power cord. Do not, under any circumstances, cut or remove the round ground
plug prong from the plug.
Your dehumidifier must be plugged directly into a properly grounded and polarized
three-prong receptacle. lf the wall receptacle you intend to use will not accept a
three-prong plug, or if you are not sure the outlet is adequately grounded or protected
by a time delay fuse or circuit breaker, have a qualified electrician install the proper outlet
according to the National Electrical Code and applicable local codes and ordinances. Do not
use an extension cord or an adapter plug.
Never unplug the dehumidifier by pulling on the power cord. Always grip the plug firmly
and pull straight out from the receptacle.
Do not pinch, bend, or knot the power cord.
SAFETY PRECAUTIONS
DANGER! Avoid Serious Injury or Death
This dehumidifier contains no user-serviceable parts. Always call an authorized Electrolux servicer for repairs.
Do not insert or place fingers or objects into the air discharge area or front grille of the unit.
Do not start or stop the dehumidifier by unplugging the power cord or turning off the power at the electrical box.
Do not cut or damage the power cord.
If the power cord is damaged, it should only be replaced by an authorized Electrolux servicer.
In the event of a malfunction (sparks, burning smell, etc.), immediately stop the operation, disconnect the power cord, and call an authorized
Electrolux servicer.
Do not operate the dehumidifier with wet hands.
Do not pull on the power cord.
Do not drink any water from the dehumidifier.
SAFETY PRECAUTIONS
CAUTION! Avoid Injury or damage to the unit or other property
Do not direct airflow at fireplaces or other heat related sources as this could cause flare ups.
Do not climb on or place objects on the unit.
Do not hang objects off the unit.
Do not place containers with liquids on the unit.
Turn off the dehumidifier at the power source when it will not be used for an extended period of time.
Operate the unit with air filter in place.
Do not block or cover the intake grille, discharge area and outlet ports.
Ensure that any electrical/electronic equipment is one yard away from the unit.
Do not use or store flammable gases near the unit.
Installation There are two accessory boxes inside the package(side panel).
The kraft box includes four castors of the dehumidifier. The instruction sheet of installing
castors is put inside the package(kraft box). Refer to the instructions for proper installation.
The white box includes a drainage joint for continuous drainage. Refer to the “Continuous
Drainage” in this manual for the proper installation of the drainage joint. If continuous
drainage is not applied, please keep the drainage joint in case of future use.
Selecting a Location
Location IMPORTANT:
1. Dehumidifier must be operated in an enclosed area to be most effective. Close all doors,
windows, and other outside openings to the room. The effectiveness of the dehumidifier
depends on the rate at which new moisture-laden air enters the room.
2. Place dehumidifier in a location that does not restrict airflow through the front of the unit
3. A dehumidifier operating in a basement will have little or no effect in drying an adjacent
enclosed storage area, such as a closet, unless there is adequate circulation of air in and out
of the area. lt may be necessary to install a second dehumidifier in the enclosed area for
satisfactory drying.
4. The dehumidifier must be installed on a level floor that will support it with a full bucket of
water.
5. There should be a minimum of 12 inches clearance around the dehumidifier.
When the unit is started, the fan begins to pull moisture-laden air across the dehumidifying coils.
How It Works The coils condense or draw moisture from the air, and air flows through the top louvers into the
room as dry, warm air. Moisture removed from air is collected in a bucket on the front of the
dehumidifier.
The unit is designed to operate between 41 °F (5 °C), and 90 °F (32 °C). The unit will not work
properly if the temperature is out of this temperature range, or the performance of the unit will
fall greatly.
The "Compressor" circuit has an automatic 3 minute time delayed start if the unit is turned off
and on quickly. This prevents overheating of the compressor and possible circuit breaker tripping.
Make sure the tank is fitted correctly otherwise unit will not turn on.
Operating Instructions
Allow the unit to reach room temperature before operating.
To begin operating the dehumidifier, follow these steps:
NOTE:
1. Plug the power cord into a properly grounded 115 volt AC outlet.
NOTE:
If the "BUCKET FULL" light is on, remove the bucket and re-install to reset the float switch.
_
+
FILTER TIMER FAN CONTI
SPEED MODE NUOUS
2. To turn the unit on, press the ON/OFF button. The unit will run in the factory setting of CONTINUOUS and high fan
speed. In the CONTINUOUS mode, the unit will display the actual room humidity. It is recommended you leave the
unit running in the CONTINUOUS setting for the first three or four days until the sweating and dampness odors have
stopped.
65
TIMER MEDIUM LIVING SPACE CONTINUOUS
LOW BASEMENT
_
+
FILTER TIMER FAN CONTI
SPEED MODE NUOUS
3. After a few days when the Relative Humidity has declined, press the HUMIDITY or+ - buttons to choose a value
between 35% to 80%, so the room is kept at a comfortable humidity. Pressing the + -
or buttons will change the
humidity selection in 5% increments. After you have set the desired humidity, the readout will display the actual
room humidity.
When unit is in operation, pressing + -
and button will simultaneously for 3 seconds can lock buttons. If this function is
enabled, LOCK indicator will illuminate and display shows LC, which will blink for 3 times. Then room humidity will be display
again. To disable this function, press + -
and button simultaneously for 3 seconds and the LOCK indicator will turn off.
LC
TIMER MEDIUM LIVING SPACE CONTINUOUS
LOW BASEMENT
_
+
FILTER TIMER FAN CONTI
SPEED MODE NUOUS
Operating Instructions
(continued)
4. You can press the MODE button to select different kinds of operating mode. After each pressing of this button, the
operating mode will switch among SLEEPING SPACE (55% RH), LIVING SPACE (50% RH), BASEMENT (45% RH) and
CONTINUOUS modes, and the corresponding mode indicators will illuminate.
NOTE:
When you press the MODE button, the unit will always display the actual room humidity instead of the
humidity settings.
65
TIMER MEDIUM LIVING SPACE CONTINUOUS
LOW BASEMENT
_
+
FILTER TIMER FAN CONTI
SPEED MODE NUOUS
5. You can also use the FAN SPEED button to change the fan speed to HIGH, Medium or LOW. The indicator light will show the
setting you have selected. A higher fan speed will result in quicker moisture removal.
65
TIMER MEDIUM LIVING SPACE CONTINUOUS
LOW BASEMENT
_
+
FILTER TIMER FAN CONTI
SPEED MODE NUOUS
6. The CLEAN FILTER light will illuminate after 250 hours of operation. At this time refer to the care and cleaning
section to remove and clean the filter. Once the filter has been cleaned and replaced, simply press the FILTER button
to extinguish the light.
65
TIMER MEDIUM LIVING SPACE CONTINUOUS
LOW BASEMENT
_
+
FILTER TIMER FAN CONTI
SPEED MODE NUOUS
7. The TIMER function enables you to either Delay Start or Delay Stop the unit in the choice from 0.5 hour to 24 hours.
If the unit is running, then selecting Timer will turn the unit off in the hours that will be set (Delay Stop). If the unit is
off, then selecting Timer will turn the unit on in the hours that will be set (Delay Start).
TIMER setting: First press TIMER button, then adjust timer setting, by tapping or holding the or+ -
button to
change the delay timer at 0.5 hour increments, up to 10 hours, then by 1 hour increments up to 24 hours. The
control will count down the time remaining (8,7.5,7, etc.) until the unit either starts or stops. For the Delay Start, the
fan speed and humidity maintained will be the same as previous setting. After TIMER setting finishes, pressing TIMER
button again at any time will stop the TIMER function. The Delay Start/Stop Feature will work until the unit either
starts or stops. Once that happens the above steps have to be repeated.
Operating Instructions
(continued)
NOTE:
1. Before entering TIMER setting, make sure power is being supplied to the unit.
2. Before entering TIMER setting, make sure pressing + or - button sets one desired room humidity first.
_
+
FILTER TIMER FAN CONTI
SPEED MODE NUOUS
_
+
FILTER TIMER FAN CONTI
SPEED MODE NUOUS
Fault Codes
1. If the display reads "F1", "F2", "F5", "L1", "C5" or "E5" error codes, please turn off and unplug the unit, then plug it
in again in 30 minutes. If the unit malfunctions still, please contact your Authorized Frigidaire Service Center.
F1
TIMER MEDIUM LIVING SPACE CONTINUOUS
LOW BASEMENT
_
+
FILTER TIMER FAN CONTI
SPEED MODE NUOUS
2.If the display reads "F0" , check the following operating conditions. Outlet voltage should be 115V±10% and the
surrounding temperature should be with in the range of 41 °F (5 °C) to 90 °F (32 °C). Unplug the unit and plug it in
again under normal operating conditions. If the "F0" code persists, contact your Authorized Frigidaire Service Center.
F0
TIMER MEDIUM LIVING SPACE CONTINUOUS
LOW BASEMENT
_
+
FILTER TIMER FAN CONTI
SPEED MODE NUOUS
65
TIMER MEDIUM LIVING SPACE CONTINUOUS
LOW BASEMENT
_
+
FILTER TIMER FAN CONTI
SPEED MODE NUOUS
b. Do not move the unit at this time otherwise water may spill on the floor.
c. Press sides of bucket gently to unclip the bucket from the unit.
d. Remove the bucket as shown in the photographs below and empty the bucket.
WARNING
Discard water from bucket. Water is not potable and cannot be used for drinking.
e. Replace the empty bucket back into the unit and once seated correctly, the unit will start up again.
f. You should hear a click when the bucket is in the correct position
If the bucket full light does not extinguish, check that the float is correctly snapped in place as indicated by the diagram.
NOTE:
The foam embedded under the float(shown in the diagram below) is a functional part, which can not be removed.
Float Foam
NOTE:
1. Check the seal between the hose and the drainage joint. If there is a small leak then replace the hose gasket and re-tighten
the hose.
2. It is recommended that a Dehumidifier Drain Hose - 11/16" (17.5 mm) or larger be used.
3. When applying continuous drainage option, place dehumidifier on a horizontal surface and make sure garden
hose is clear of any obstructions and directed downward. Improper installation or use of hose may result in
water filling up the bucket and causing the unit to shut off. Empty water bucket if shut-off occurs, then check
dehumidifier location and hose for proper installation. (fig.7)
fig. 7
Storage
When unit is not in use, unplug and tidy up the cord as shown below.
Before calling for service, review this list. It may save you time and expense. This list includes common occurrences that are not
the result of defective workmanship or materials in this appliance.
OCCURRENCE SOLUTION
DEHUMIDIFIER DOES NOT Wall plug disconnected. Push plug firmly into wall outlet.
OPERATE.
House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker.
The dryness level you selected has been reached. Dehumidifier automatically shuts off when selected
amount of moisture has been removed from the air. If you want to remove more moisture, Select
'CONTINUOUS' by using the humidity button. After the dehumidifier starts, reset the control to the
desired setting.
Bucket not installed properly. See “Removing Collected Water“.
Water in the bucket has reached its preset level. Dehumidifier automatically turns off when this
occurs. Empty bucket and return bucket to position.
DEHUMIDIFIER RUNS TOO MUCH. Windows or doors near dehumidifier are open to outdoors. Close all windows or doors to outside.
Area to be dehumidified is too large. Check with your dealer to see if capacity is adequate.
O
Air movement through dehumidifier is blocked. Grill may be dirty. Use brush attachment of vacuum
cleaner to clean grill. See “Care and Cleaning“. Dehumidifier must be placed in a space that does
not restrict air flowing into the rear coil or out of the front grill.
Dehumidifier has been installed or restarted recently. The higher the moistuire in the room, the longer
the dehumidifier will operate.
Dehumidifier is in the CONTINUOUS mode and will remain on in this mode, use the humidity button or
knob to set a RH% higher level.
DEHUMIDIFIER IS OPERATING Humidity setting is too high. Press the setting button to a lower setting or choose CONTINUOUS for
BUT ROOM IS NOT DRY ENOUGH. maximum dryness.
Dehumidifier has been installed or restarted recently. The higher the moisture in the room air, the
longer it takes for the room air to become dry.
Dehumidifier does not have sufficient clearance to operate. Air flow to front grill is blocked. See
“Selecting a Location“.
Room temperature is too low. Unit will not operate satisfactorily if the room temperature is below
41 °F(5 °C). See “Operating Conditions“.
Refer to causes under DEHUMlDIFIER RUNS TOO MUCH.
FROST APPEARS ON COILS ABOVE If unit operates in a room where temperature is from 41°F(5°C) to 59°F(15°C), it will start defrosting
BUCKET. automatically. Compressor will stop for a brief period of time(fan will operate in high fan speed). When
unit finishes defrosting, it will be back to normal operation.
NOISE. Air is moving through the dehumidifier. The fan noise is normal sound. The unit is placed on uneven
surface or wooden floor.
WATER FLOWS INTO THE BUCKET, Refer to “Continuous Drainage” for proper installation of garden hose and drainage joint.
EVEN WHEN GARDEN HOSE IS
EQUIPPED.
Your appliance is covered by a limited one-year warranty and a limited 2-5 year warranty on the sealed system (the compressor,
condenser, evaporator and tubing). For one year from your original date of purchase, Electrolux will pay all costs for repairing or
replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed,
used and maintained in accordance with the provided instructions. From the second to the fifth year from your original purchase
date, Electrolux will repair or replace any parts in the Sealed Refrigeration System (compressor, condenser, evaporator and tubing)
that prove to be defective in materials or workmanship. In years 2-5, the consumer will be responsible for diagnostic, labor and
parts costs as well as any removal, transportation and reinstallation expenses which are incurred during service on components
other than those covered under the Sealed Refrigeration System 5-year warranty.
If You Need Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period
Service should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.
Service under this warranty must be obtained by contacting Electrolux at the addresses or phone
numbers below.
This limited warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances
North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp.
Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts under
this warranty must be performed by Electrolux or an authorized service company. Product features or specifications as described
or illustrated are subject to change without notice.
USA Canada
1.800.944.9044 1.800.265.8352
Electrolux Major Appliances Electrolux Canada Corp.
10200 David Taylor Drive 5855 Terry Fox Way
Charlotte, NC 28262 Mississauga, Ontario, Canada
L5V 3E4