International Standard
International Standard
International Standard
STANDARD 6469-3
Second edition
2011-12-01
Reference number
ISO 6469-3:2011(E)
--`,,```,,,,````-`-`,,`,,`,`,,`---
ii Provided by IHS under license with ISO © ISO 2011 – All rights reserved
Copyright International Organization for Standardization
Not for Resale
ISO 6469-3:2011(E)
Contents Page
--`,,```,,,,````-`-`,,`,,`,`,,`---
© ISO 2011 – All rights reserved Provided by IHS under license with ISO iii
Copyright International Organization for Standardization
Not for Resale
ISO 6469-3:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
--`,,```,,,,````-`-`,,`,,`,`,,`---
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 6469-3 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 21,
Electrically propelled road vehicles.
This second edition cancels and replaces the first edition (ISO 6469-3:2001), which has been technically
revised. Technical Corrigendum ISO 6469-3:2001/Cor.1:2003 has been incorporated.
ISO 6469 consists of the following parts, under the general title Electrically propelled road vehicles — Safety
specifications:
iv Provided by IHS under license with ISO © ISO 2011 – All rights reserved
Copyright International Organization for Standardization
Not for Resale
INTERNATIONAL STANDARD ISO 6469-3:2011(E)
IMPORTANT — The electronic file of this document contains colors which are considered to be useful
for the correct understanding of the document. Users should therefore consider printing this
document using a color printer.
1 Scope
This part of ISO 6469 specifies requirements for the electric propulsion systems and conductively connected
auxiliary electric systems, if any, of electrically propelled road vehicles for the protection of persons inside and
outside the vehicle against electric shock.
It does not apply to motorcycles and vehicles not primarily intended as road vehicles, such as material
handling trucks or forklifts.
It applies only to on-board electric circuits with maximum working voltages according to voltage class B.
It does not provide comprehensive safety information for manufacturing, maintenance and repair personnel.
NOTE Requirements for the electric power supply interface conductively connected to the external power supply
(grid) for charging the RESS are also specified in IEC 61851-1 and IEC 61851-21.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 6469-1, Electrically propelled road vehicles — Safety specifications — Part 1: On-board rechargeable
energy storage system (RESS)
ISO 7010, Graphical symbols — Safety colours and safety signs — Registered safety signs
ISO 20653, Road vehicles — Degrees of protection (IP-Code) — Protection of electrical equipment against
foreign objects, water and access
IEC 60664 (all parts), Insulation coordination for equipment within low-voltage systems
© ISO 2011 – All rights reserved Provided by IHS under license with ISO 1
Copyright International Organization for Standardization
Not for Resale
ISO 6469-3:2011(E)
3.1
auxiliary electric system
on-board vehicle system, other than the propulsion system, that operates on electric energy
3.2
balance of electric power system
remaining portion of a voltage class B (3.31) electric circuit when all RESS and fuel cell stacks (3.18) are
disconnected
3.3
barrier
part providing protection against direct contact from any usual direction of access
3.4
basic insulation
insulation applied to live parts (3.22) for protection against direct contact (3.10)
NOTE Basic insulation does not necessarily include isolations used exclusively for functional purposes.
3.5
basic protection
protection against direct contact (3.10) with live parts (3.22) under fault-free conditions
3.6
battery pack
mechanical assembly comprising battery cells and retaining frames or trays, and possibly components for
battery management
3.7
clearance
shortest distance in air between conductive parts (3.8)
3.8
conductive part
part capable of conducting electric current
3.9
creepage distance
shortest distance along the surface of a solid insulating material between two conductive parts (3.8)
3.10
direct contact
contact of persons with live parts (3.22)
3.11
double insulation
insulation system comprising both basic insulation (3.4) and supplementary insulation (3.28)
3.12
electric chassis
--`,,```,,,,````-`-`,,`,,`,`,,`---
conductive parts (3.8) of a vehicle that are electrically connected and whose potential is taken as reference
3.13
electric shock
physiological effect resulting from an electric current passing through a human body
2 Provided by IHS under license with ISO © ISO 2011 – All rights reserved
Copyright International Organization for Standardization
Not for Resale
ISO 6469-3:2011(E)
3.14
electrically propelled vehicle
vehicle with one or more electric drive(s) (3.15) for vehicle propulsion
3.15
electric drive
combination of traction motor, power electronics and their associated controls for the conversion of electric to
mechanical power and vice versa
3.16
enclosure
part providing protection of equipment against direct contact (3.10) from any direction
3.17
3.18
fuel cell stack
assembly of two or more fuel cells that are electrically connected
3.19
fuel cell system
system, typically containing the following subsystems: fuel cell stack (3.18), air processing, fuel processing,
thermal management, water management, and their control
3.20
isolation resistance
resistance between live parts of voltage class B (3.31) electric circuit and the electric chassis (3.12) as well
as the voltage class A (3.30) system
3.21
isolation resistance monitoring system
system that periodically or continuously monitors the isolation resistance (3.20) between live parts (3.22)
and the electric chassis (3.12)
3.22
live part
conductor or conductive part (3.8) intended to be electrically energized in normal use
3.23
maximum working voltage
highest value of a.c. voltage (rms) or of d.c. voltage that can occur in an electric system under any normal
operating conditions according to the manufacturer's specifications, disregarding transients
3.24
potential equalization
electric connections of exposed conductive parts (3.8) of the electric equipment to minimize differences in
potential between these parts
3.25
protection degree
protection provided by a barrier (3.3)/enclosure (3.16) related to the contact with live parts (3.22) by a test
probe, such as a test finger (IPXXB), a test rod (IPXXC), or a test wire (IPXXD) in accordance with ISO 20653
© ISO 2011 – All rights reserved Provided by IHS under license with ISO 3
Copyright International Organization for Standardization
Not for Resale
ISO 6469-3:2011(E)
3.26
rechargeable energy storage system
RESS
system that stores energy for delivery of electric energy and that is rechargeable
3.27
reinforced insulation
insulation of live parts (3.22) for protection against electric shock (3.13) equivalent to double insulation (3.11)
NOTE Reinforced insulation does not imply that the insulation shall be a homogeneous piece. The reinforced
insulation may be composed of several layers that cannot be tested individually as supplementary or basic insulation.
3.28
supplementary insulation
independent insulation applied in addition to basic insulation (3.4) for protection against electric shock
(3.13) in the event of a failure of the basic insulation (3.4)
3.29
traction battery
collection of all battery packs (3.6) that are electrically connected, for the supply of electric power to the
electric drive (3.15) and to the conductively connected auxiliary electric system, if any
3.30
voltage class A
classification of an electric component or circuit with a maximum working voltage of less than 30 V a.c. (rms)
or 60 V d.c.
3.31
voltage class B
classification of an electric component or circuit with a maximum working voltage between 30 V a.c. (rms) and
1 000 V a.c. (rms) or between 60 V d.c. and 1 500 V d.c.
5 Voltage classes
Depending on its maximum working voltage, U, an electric component or circuit belongs to one of the voltage
classes specified in Table 1.
--`,,```,,,,````-`-`,,`,,`,`,,`---
NOTE The values 60 V d.c./30 V a.c. (rms) are selected taking into account humid weather conditions.
4 Provided by IHS under license with ISO © ISO 2011 – All rights reserved
Copyright International Organization for Standardization
Not for Resale
ISO 6469-3:2011(E)
6 Marking
The symbol W 012 in accordance with ISO 7010 shown in Figure 1 shall appear on (preferably) or near
voltage class B electric power sources as RESS and fuel cell stacks.
The same symbol shall be visible on barriers and enclosures, which, when removed, expose live parts of
voltage class B electric circuits. Accessibility and removability of barriers/enclosures should be considered
when evaluating the requirement for the symbol.
The outer covering of cables and harness for voltage class B electric circuits not within enclosures or behind
barriers shall be marked with orange color.
Voltage class B connectors may be identified by the harnesses to which the connector is attached.
NOTE Specifications of the orange color are given e.g. in standards in the US (8.75R5.75/12.5) and in Japan
(8.8R5.8/12.5) according to the Munsell color system.
7.1 General
The protection measures shall meet the requirements as described in 7.2 and 7.3 and compliance shall be
tested in accordance with the test methods specified in Clause 8.
Persons shall be protected against direct contact with the live parts of the voltage class B electric circuits.
The protection measures against direct contact shall be provided by either one or both of the following:
© ISO 2011 – All rights reserved Provided by IHS under license with ISO 5
Copyright International Organization for Standardization
Not for Resale
ISO 6469-3:2011(E)
As a general rule, exposed conductive parts of voltage class B electric equipment, including exposed
conductive barriers/enclosures, shall be bonded to the electric chassis for potential equalization in accordance
with the requirements in 7.9.
The voltage class B electric circuits intended to be not conductively connected to the grid shall have sufficient
isolation resistance in accordance with the requirements in 7.7.
If the minimum isolation resistance requirement of such circuits cannot be maintained under all operational
conditions and over the entire service life, one of the following measures shall be applied:
one or more layers of insulation, barriers and/or enclosures in addition to the basic protection;
rigid barriers/enclosures with sufficient mechanical robustness and durability, over the vehicle service life.
Requirements on isolation resistance for voltage class B electric circuits intended to be conductively
connected to the grid are given in 7.10.2.
NOTE 1 Isolation resistances below the required minimum values can occur due to deterioration of fuel cell (FC)
systems' cooling liquids or of certain battery types.
NOTE 2 Coordination between multiple isolation monitoring systems can be necessary, e.g. during charging.
NOTE 3 The isolation resistance is approximately zero for a voltage class B electric circuit conductively connected to
the grid.
NOTE 4 Additional layer(s) of insulation and double or reinforced insulation include, but are not limited to, those for
voltage class B wiring.
NOTE 5 The rigid barriers/enclosures include, but are not limited to, power control enclosures, motor housings,
connector casings and housings, etc. They can be used as single measure instead of basic barriers/enclosures to meet
both basic and single-failure protection requirements.
7.3.3.1 Capacitive couplings between a voltage class B potential and electric chassis usually result from
Y capacitors, used for electromagnetic compatibility (EMC) reasons, or parasitic capacitive couplings.
7.3.3.2 For d.c. body currents caused by discharge of such capacitive couplings when touching d.c.
--`,,```,,,,````-`-`,,`,,`,`,,`---
energy of the total capacitance between any energized voltage class B live part and the electric chassis
shall be 0,2 J at its maximum working voltage; total capacitance should be calculated based on
designed values of related parts and components;
alternative mechanical or electrical measures for d.c. voltage class B electric circuits; see 7.3.3.4.
6 Provided by IHS under license with ISO © ISO 2011 – All rights reserved
Copyright International Organization for Standardization
Not for Resale
ISO 6469-3:2011(E)
7.3.3.3 For a.c. body currents caused by such capacitive couplings when touching a.c. class B voltage
one of the following options shall be fulfilled:
a.c. body current shall not exceed 5 mA when measured in accordance with IEC 60950-1;
alternative mechanical or electrical measures for a.c. voltage class B electric circuits; see 7.3.3.4.
one or more layers of insulation, barriers and/or enclosures in addition to the basic protection;
rigid barriers/enclosures with sufficient mechanical robustness and durability, over the vehicle service life.
7.3.4 De-energization
The voltage class B electric circuit in question may be de-energized as a protection measure. The monitoring
of faults within the circuit or the detection of events may be used to trigger the de-energization. One of the
following conditions shall be met for the de-energized circuit.
The voltage shall be reduced to less than 30 V a.c. (rms) for a.c. circuits and 60 V d.c. for d.c. circuits.
The transition time to reach the de-energized state shall be specified by the manufacturer in accordance with
expected failures and operating conditions.
As an alternative to 7.3, the vehicle manufacturer shall conduct an appropriate hazard analysis and establish
a set of measures which give sufficient protection against electric shock under single-failure conditions.
If protection is provided by insulation, the live parts of the electric system shall be totally encapsulated by
insulation that can be removed only by destruction.
The insulating material shall be suitable to the maximum working voltage and temperature ratings of the
vehicle and its systems (see also Clause 4).
The insulation shall have sufficient capability to withstand the usual voltage. Compliance shall be tested in
accordance with 8.3.
7.6.1 General
If protection is provided by barriers/enclosures, live parts shall be placed inside enclosures or behind barriers,
preventing access to the live parts from any usual direction of access.
The barriers/enclosures shall provide sufficient mechanical resistance under normal operating conditions, as
specified by the manufacturer.
If barriers/enclosures are accessible directly, they shall be opened or removed only by use of tools or
maintenance keys or they shall have means to deactivate live parts with class B voltage, e.g. an interlock.
7
--`,,```,,,,````-`-`,,`,,`,`,,`---
© ISO 2011 – All rights reserved Provided by IHS under license with ISO
Copyright International Organization for Standardization
Not for Resale
ISO 6469-3:2011(E)
Barriers/enclosures in passenger and load compartments shall comply with the protection degree IPXXD at a
minimum.
If connector parts can be disconnected without tools and can have class B voltage in the unmated condition,
the connector shall comply with IPXXB at a minimum in the unmated condition.
7.7.1 General
The minimum isolation resistance shall be at least 100 /V for d.c. circuits and at least 500 /V for a.c.
circuits. The reference shall be the maximum working voltage.
NOTE Hazard of electric shock occurs when electric currents depending on value and duration pass through the
human body. Harmful effects can be avoided if the current is within zone DC-2 for d.c. or zone AC-2 for a.c. as shown in
IEC/TS 60479-1:2005, Figure 20 and Figure 22, respectively. The relation of harmful body currents and other wave forms
and frequencies is described in IEC/TS 60479-2. The isolation resistance requirements of 100 /V for d.c. or 500 /V for
a.c. allow body currents of 10 mA and 2 mA, respectively.
To meet the above requirement for the entire circuit, it is necessary to have a higher isolation resistance for
each component, depending on the number of the components and the structure of the circuit to which they
belong.
If d.c. and a.c. voltage class B electric circuits are conductively connected (see Figure 2), one of the following
two options shall be fulfilled.
Option 1: Meet at least the 500 /V requirement for the combined circuit.
Option 2: Meet at least the 100 /V requirements for the entire conductively connected circuit, if at least
one of the additional protection measures as defined in 7.7.2 is applied to the a.c. circuit.
One or a combination of the following measures in addition to or instead of the basic protection measures as
described in 7.2 shall be applied to provide protection against single failures to address the failures, for which
it is intended:
--`,,```,,,,````-`-`,,`,,`,`,,`---
one or more layers of insulation, barriers and/or enclosures in addition to the basic protection;
rigid barriers/enclosures with sufficient mechanical robustness and durability, over the vehicle service life.
8 Provided by IHS under license with ISO © ISO 2011 – All rights reserved
Copyright International Organization for Standardization
Not for Resale
ISO 6469-3:2011(E)
a) Option 1 b) Option 2
Key
1 fuel cell system
2 traction battery
3 inverter
4 vehicle electric chassis
a a.c. circuit.
NOTE Figure 2 is based on fuel cell hybrid electric vehicle (FCHEV) as an example.
--`,,```,,,,````-`-`,,`,,`,`,,`---
The resistance of the potential equalization path between any two exposed conductive parts of the voltage
class B electric circuit that can be touched simultaneously by a person shall not exceed 0,1 .
The vehicle power inlet shall comply with at least one of the following requirements:
7.10.2 Grounding and isolation resistance requirement for the vehicle power inlet
The vehicle power inlet intended to be conductively connected to the grid shall have a terminal for connecting
the vehicle electric chassis to the ground of the grid.
The total isolation resistance at the vehicle power inlet, which includes circuits conductively connected to the
grid during charging, shall be at least 1 M when the charge coupler is disconnected.
© ISO 2011 – All rights reserved Provided by IHS under license with ISO 9
Copyright International Organization for Standardization
Not for Resale
ISO 6469-3:2011(E)
The total isolation resistance of the vehicle power inlet, which includes circuits conductively connected to the
inlet during charging, shall comply with the requirements in 7.7 when the charge coupler is disconnected.
A terminal connecting the vehicle chassis to the external power supply shall be provided if potential
equalization is required.
8.1 General
The tests to verify the protection measures according to Clause 7 shall in principle be performed on each
voltage class B electric circuit on the vehicle, when the charge coupler is disconnected.
If the safety aspects in relation to the whole vehicle are not affected, the tests may be performed outside the
vehicle on the components or parts of the voltage class B electric circuits individually instead.
Prior to the measurement, the device under test (DUT) shall be subjected to a preconditioning period of at
least 8 h at (5 2) °C, followed by a conditioning period of 8 h at a temperature of (23 5) °C, a humidity of
90 10
5
%, and an atmospheric pressure of between 86 kPa and 106 kPa.
Alternative preconditioning and conditioning parameters may be selected provided transition across the dew
point occurs shortly after the beginning of the conditioning period.
The isolation resistance shall be measured during the conditioning period at a rate from which the lowest
value can be determined.
The test voltage shall be a d.c. voltage of at least the maximum working voltage of the voltage class B power
system and be applied for a time long enough to obtain stable reading.
If the system has several voltage ranges (e.g. because of boost converter) in conductively connected circuit
and some of the components cannot withstand the maximum working voltage of the entire circuit, the isolation
resistances of components can be measured separately by applying their own maximum working voltages
after those components are disconnected.
The following test procedure combines the measurement of the isolation resistance of the live parts of the
voltage class B balance of electric power systems against the vehicle electric chassis and against the live
parts of the voltage class A balance of auxiliary electric systems.
Traction batteries shall be disconnected at their terminals from the power system.
Electric power sources of the voltage class B power systems other than the traction batteries (fuel cell
stacks, capacitors) may be disconnected at their terminals from the power system; if they remain
connected, power generation shall be deactivated.
All live parts of the balance of electric power systems (voltage class B) shall be connected to each other.
All exposed conductive parts of the balance of electric power system shall be connected to the electric
chassis.
10 --`,,```,,,,````-`-`,,`,,`,`,,`---
Provided by IHS under license with ISO © ISO 2011 – All rights reserved
Copyright International Organization for Standardization
Not for Resale
ISO 6469-3:2011(E)
Batteries of the auxiliary electric systems (voltage class A) shall be disconnected at their terminals from
the auxiliary circuits.
All live parts of the balance of auxiliary electric systems (voltage class A) shall be connected to the
electric chassis.
Then the test voltage shall be applied between the connected live parts of the voltage class B balance of
electric power systems and the electric chassis.
The measurements shall be performed using suitable instruments that can apply d.c. voltage
(e.g. megohmmeter, provided they deliver the required test voltage).
Alternatively the isolation resistance may be measured using the test procedure for the measurement of the
RESS as given in ISO 6469-1 with the balance of electric power system connected to an external power
source.
8.2.3 Isolation resistance measurement of the voltage class B electric power sources
The measurement of the isolation resistance of an RESS, if any, shall be in accordance with ISO 6469-1.
The measurement of the isolation resistance of a fuel cell stack, if any, shall be in accordance with
ISO 6469-1 with the fuel cell stack in operation.
Alternatively for the measurement of the isolation resistance of a fuel cell stack, the entire mechanical
structure of the fuel cell system (including the cooling system with its cooling medium) shall be considered.
Prior to the measurement, stop power generation after operation at maximum output according to the
manufacturer's specification. The voltage across the fuel-cell stack power terminals shall be discharged. All
cables shall be disconnected from the fuel-cell stack power terminals, and all other cables from other electric
terminals of the fuel-cell stack. All cooling pipes, fuel pipes, and air pipes shall remain connected. The applied
test voltage shall be at least the maximum open circuit voltage of the fuel cell stack. Apart from these specific
conditions, the procedure shall be performed as given in 8.2.2.
The isolation resistance of entire conductively connected voltage class B electric circuits may be measured
using the test procedure for the measurement of the RESS given in ISO 6469-1 with the balance of electric
power system connected to the voltage class B power sources.
Alternatively, the isolation resistance of entire conductively connected voltage class B electric circuits may be
measured using an isolation resistance monitoring system, if installed on the vehicle, provided that its
accuracy is sufficiently high.
In case electric or electronic switches exist in the circuit (e. g. transistors in power electronics), these switches
shall be activated. If these switches cannot be activated, the relevant part of the circuit may be measured
separately in accordance with 8.2.2.
Instead of being measured, the isolation resistance of the entire conductively connected circuit may be
calculated using the measured resistances of the power sources and the balance of electric power system.
8.3.1 General
This test is intended to demonstrate the adequacy of the protection measures to isolate live parts of voltage
class B electric circuits.
This test shall be applied for the balance of the electric power system.
The test may be performed at the component level at the discretion of the manufacturer.
--`,,```,,,,````-`-`,,`,,`,`,,`---
© ISO 2011 – All rights reserved Provided by IHS under license with ISO 11
Copyright International Organization for Standardization
Not for Resale
ISO 6469-3:2011(E)
Surge protective devices (SPDs) that can affect the test result shall be disconnected before testing.
Components such as RFI filters shall be included in the impulse test, but it can be necessary to disconnect
them during a.c. tests.
NOTE Test procedures and criteria of high voltage cables conductively connected to grid are specified in applicable
sections of appropriate IEC standards (e.g. IEC 60227, IEC 60245, etc.).
If not otherwise specified by the vehicle manufacturer, the following procedure shall apply.
8.3.3.1 General
8.3.3.1.1 This test shall include barriers/enclosures, unless evaluations prove otherwise.
All voltage class B live parts of the DUT shall be connected to each other.
For components with conductive housing, all live parts of the voltage class A electric circuit of the DUT
and all exposed conductive parts of the DUT shall be connected to each other.
For components with non-conductive housing, all live parts of the voltage class A electric circuit of the
DUT and an electrode wrapped around the housing shall be connected to each other.
8.3.3.1.3 At the end of the conditioning, the test voltage specified in 8.3.3.2 or 8.3.3.3 shall be applied:
between connected live parts of voltage class B electric circuits and a housing with an electrically
conductive surface;
between connected live parts of voltage class B electric circuits and an electrode wrapped around the
housing in the case of non-conductive housing.
--`,,```,,,,````-`-`,,`,,`,`,,`---
8.3.3.2 Test voltage for components not conductively connected to the grid
The test voltage, a.c. or d.c., shall be more than the highest voltage that can actually occur to the component.
The test voltage shall be derived from the relevant over-voltages of the electric circuit to which the component
is connected. Transient over-voltages that can be expected, including influences from other connections to
grid, if any, shall be considered. The test voltage and its duration shall be specified, considering the applicable
parts and sections of IEC 60664 by the vehicle manufacturer.
These test requirements also apply for voltage class B components connected to d.c. charging systems that
are not conductively connected to the a.c. grid.
8.3.3.3.1 General
These test requirements also apply for voltage class B components connected to d.c. charging systems that
are conductively connected to the a.c. grid.
12 Provided by IHS under license with ISO © ISO 2011 – All rights reserved
Copyright International Organization for Standardization
Not for Resale
ISO 6469-3:2011(E)
The following a.c. test voltage of a frequency between 50 Hz and 60 Hz shall be applied for 1 min:
(2U 3 250) V a.c. (rms) if double insulation and reinforced insulation applies;
where U, expressed in volts, is the maximum working voltage of the electric circuit to which the component is
connected.
The equivalent d.c. test voltage is 1,41 times the a.c. (rms) value.
This test condition is specified in IEC 60664-1 for verifying the withstand voltage capability. Both test voltages
for impulse voltage withstand test and a.c. voltage test shall be applied.
For the impulse voltage withstand test, the applicable test voltages given in IEC 60664-1 for over-voltage
category I or category II shall be applied. 160 % of the voltage value shall be applied for double insulation or
reinforced insulation.
The over-voltage category I or category II in accordance with IEC 60664-1 shall be selected by the vehicle
manufacturer.
For the a.c. voltage test, Un 1 200 V (rms) for 60 s where Un is the nominal line-to-neutral voltage of the
--`,,```,,,,````-`-`,,`,,`,`,,`---
neutral-earthed supply system. Twice the voltage value shall be applied for double insulation or reinforced
insulation.
Neither dielectric breakdown nor flashover shall occur during application of the test voltage.
The potential equalization resistances shall be tested with a test current of at minimum 1 A and a voltage
60 V d.c., which shall be passed through the potential current path between any two exposed conductive
parts for at least 5 s. This path shall be isolated from other unintended potential paths for measurement.
These conducting parts shall include voltage class B component housings, connections to electric chassis and
the vehicle electric chassis or barriers/enclosures.
A lower test current and/or a shorter test time may be used, provided the accuracy of the potential
equalization resistance test results remain on a sufficiently accuracy level.
The voltage drop between any two reachable exposed conductive parts in a distance of 2,5 m shall be
measured and the resistance calculated from the current and this voltage drop.
© ISO 2011 – All rights reserved Provided by IHS under license with ISO 13
Copyright International Organization for Standardization
Not for Resale
ISO 6469-3:2011(E)
Bibliography
[1] IEC 60227 (all parts), Polyvinyl chloride insulated cables of rated voltages up to and including
450/750 V
[2] IEC 60245 (all parts), Rubber insulated cables — Rated voltages up to and including 450/750 V
[3] IEC/TS 60479-1:2005, Effects of current on human beings and livestock — Part 1: General aspects
[4] IEC/TS 60479-2, Effect of current on human beings and livestock — Part 2: Special aspects
[5] IEC 60950-1, Information technology equipment — Safety — Part 1: General requirements
[6] IEC 61851-1, Electric vehicle conductive charging system — Part 1: General requirements
[7] IEC 61851-21, Electric vehicle conductive charging system — Part 21: Electric vehicle requirements
for conductive connection to an a.c./d.c. supply
[8] ISO 16750 (all parts), Road vehicles — Environmental conditions and testing for electrical and
electronic equipment
--`,,```,,,,````-`-`,,`,,`,`,,`---
14 Provided by IHS under license with ISO © ISO 2011 – All rights reserved
Copyright International Organization for Standardization
Not for Resale
--`,,```,,,,````-`-`,,`,,`,`,,`---
ICS 43.120
Price based on 14 pages
--`,,```,,,,````-`-`,,`,,`,`,,`---
© ISO 2011 – All rights reserved Provided by IHS under license with ISO
Copyright International Organization for Standardization
Not for Resale