En Acs800 17 Hwman e Scrres

ACS800
Hardware Manual
ACS800-17 Drives (55 to 2500 kW / 75 to 2800 hp)
List of related manuals
Drive hardware manuals and guides
ACS800-17 Drives (55 to 2500 kW / 75 to 2800 hp) 3AFE68397260
Hardware Manual
Drive (inverter) firmware manuals and guides

ACS800 Standard Control Program Firmware Manual 3AFE64527592
ACS800 System Control Program Firmware Manual 3AFE64670646
Master/Follower Application Guide Supplement to 3AFE64590430
Firmware Manual for ACS800 Standard Application
Program
ACS800 Pump Control Program Firmware Manual 3AFE68478952
Adaptive Programming Application Guide 3AFE64527274
Option manuals and guides

Safety options for ACS800 cabinet-installed drives (+Q950, 3AUA0000026238
+Q951, +Q952, +Q963, +Q964, +Q967 and +Q968)
Wiring, start-up and operation instructions
Cabinet Options for ACS800-07/U7/17/37 Description 3AUA0000053130
ATEX-certified thermal motor protection functions for 3AUA0000082378
ACS800 cabinet-installed drives (+L513+Q971 and
+L514+Q971) Safety, wiring, start-up and operation
instructions
Manuals and quick guides for I/O extension modules,
fieldbus adapters, etc.
You can find manuals and other product documents in PDF format on the Internet. See section
Document library on the Internet on the inside of the back cover. For manuals not available in the
Document library, contact your local ABB representative.
ACS800-17 manuals
ACS800-17 Drives
55 to 2500 kW (75 to 2800 hp)
Hardware Manual
3AFE68397260 REV E EN
EFFECTIVE: 2013-02-14
© 2013 ABB Oy. All Rights Reserved.

5
Safety instructions
What this chapter contains

This chapter contains safety instructions you must follow when installing, operating
and servicing the drive. If ignored, physical injury or death may follow, or damage
may occur to the drive, the motor or driven equipment. Read the safety instructions
before you work on the unit.
Usage of warnings and notes

There are two types of safety instructions throughout this manual: warnings and
notes. Warnings caution you about conditions which can result in serious injury or
death and/or damage to the equipment, and advise on how to avoid the danger.
Notes draw attention to a particular condition or fact, or give information on a
subject. The warning symbols are used as follows:
Dangerous voltage warning warns of high voltages which can cause

physical injury and/or damage to the equipment.
General warning warns about conditions, other than those caused by

electricity, which can result in physical injury and/or damage to the
equipment.
Electrostatic discharge warning warns of electrostatic discharge which
can damage the equipment.
Safety instructions
6
Installation and maintenance work

These warnings are intended for all who work on the drive, motor cable or motor.
Ignoring the instructions can cause physical injury or death, or damage the
equipment.
WARNING!
• Only qualified electricians are allowed to install and maintain the drive.
• The main switch on the cabinet door does not remove the voltage from the input
busbars of the drive. Before working on the drive, isolate the whole drive from
the supply.
• Never work on the drive, the motor cable or the motor when main power is
applied. After switching off the input power, always wait for 5 min to let the
intermediate circuit capacitors discharge before you start working on the drive,
the motor or the motor cable. Measure the voltage between terminals UDC+
and UDC- (L+ and L–) with a multimeter (impedance at least 1 Mohm) to
ensure that the drive is discharged before beginning work.
• Apply temporary grounding before working on the unit.
• Do not work on the control cables when power is applied to the drive or to the
external control circuits. Externally supplied control circuits may cause
dangerous voltages to exist inside the drive even when the main power of the
drive is switched off.
• Do not make any insulation or voltage withstand tests on the drive or drive
modules.
• When reconnecting the motor cable, always check that the phase order is
correct.
• When joining shipping splits (if any), check the cable connections at the joints
before switching on the supply voltage.
• Live parts on the inside of the doors are protected against direct contact.
Special attention shall be paid when handling metallic shrouds.
• After maintaining or modifying a drive safety circuit or changing circuit boards

inside the module, retest the functioning of the safety circuit according to the
start-up instructions.
• Do not change the electrical installations of the drive except for the essential
control and power connections. Changes may affect the safety performance or
operation of the drive unexpectedly. All customer-made changes are on the
customer's responsibility.
Note:
• The motor cable terminals on the drive are at a dangerously high voltage when
the input power is on, regardless of whether the motor is running or not.
Safety instructions
7
• The brake control terminals (UDC+, UDC-, R+ and R- terminals) carry a

dangerous DC voltage (over 500 V).
• Depending on the external wiring, dangerous voltages (115 V, 220 V or 230 V)

may be present on the relay outputs of the drive system.
• The Prevention of unexpected start-up function (option +Q950) does not

remove the voltage from the main and auxiliary circuits.
• The Safe torque off function (option +Q968) does not remove the voltage from
the main and auxiliary circuits.
Safety instructions
8
WARNING! Ignoring the following instructions can cause physical injury or death, or
damage to the equipment.
• Use extreme caution when manoeuvring an inverter, supply or filter module that
runs on wheels. The modules are heavy and have a high centre of gravity. They
topple over easily if handled carelessly.
• Do not use the ramp which is supplied with the drive with heights over 50 mm
(the standard plinth height of ABB cabinets). The ramp is designed for a plinth
height of 50 mm.
Support the top and Do not tilt! Extend the support legs outside the
bottom of the module cabinet!
while removing!
max 50 mm
Lift the module by the upper part only Mind your fingers! Keep fingers away from the Support the top and bottom
using the lifting hole(s) at the top! edges of the front flange of the module! of the module while
replacing!
Safety instructions
9
• When removing a module which is equipped with wheels, pull the module
carefully out of the cubicle along the ramp. Make sure that the wires do not
catch. While pulling on the handle, keep a constant pressure with one foot on
the base of the module to prevent the module from falling on its back.
• When replacing a module which is equipped with wheels, push the module up
the ramp and back into the cubicle. Keep your fingers away from the edge of
the module front plate to avoid pinching them between the module and the
cubicle. Also, keep a constant pressure with one foot on the base of the module
to prevent the module from falling on its back.
• Electrically conductive dust inside the unit may cause damage or lead to
malfunction. Make sure that dust from drilling does not enter the drive when
installing.
• Fastening the cabinet by riveting or welding is not recommended. However, if

welding is necessary, ensure the return wire is properly connected in order not
to damage the electronic equipment in the cabinet. Also ensure that welding
fumes are not inhaled.
• Ensure sufficient cooling of the unit.
• Cooling fans may continue to rotate for a while after the disconnection of the
electrical supply.
• Some parts inside the drive cabinet, such as heatsinks of power

semiconductors, remain hot for a while after the disconnection of the electrical
supply.
WARNING!
• The printed circuit boards contain components sensitive to electrostatic

discharge. Wear a grounding wrist band when handling the boards. Do not
touch the boards unnecessarily.
Grounding
These instructions are intended for all who are responsible for the grounding of the
drive. Incorrect grounding can cause physical injury, death or equipment malfunction
and increase electromagnetic interference.
WARNING!
• Ground the drive, the motor and adjoining equipment to ensure personnel
safety in all circumstances, and to reduce electromagnetic emission and pick-
up.
• Make sure that grounding conductors are adequately sized as required by

safety regulations.
• In a multiple-drive installation, connect each drive separately to protective

earth (PE).
Safety instructions
10
• Do not install a drive equipped with an EMC (line) filter to an ungrounded

power system or a high resistance-grounded (over 30 ohms) power system.
Note:
• Power cable shields are suitable for equipment grounding conductors only
when adequately sized to meet safety regulations.
• As the normal leakage current of the drive is higher than 3.5 mA AC or

10 mA DC, a fixed protective earth connection is required by EN 61800-5-1,
4.3.5.5.2. The cross-section of the protective grounding conductor must be at
least 10 mm2 Cu or 16 mm2 Al.
Fibre optic cables
WARNING!
• Handle the fibre optic cables with care. When unplugging optic cables, always
grab the connector, not the cable itself. Do not touch the ends of the fibres with
bare hands as the fibre is extremely sensitive to dirt. The minimum allowed
bend radius is 35 mm (1.4 in.).
Safety instructions
11
Operation
These warnings are intended for all who plan the operation of the drive or operate
the drive. Ignoring the instructions can cause physical injury or death or damage the
equipment.
WARNING!
• Before adjusting the drive and putting it into service, make sure that the motor
and all driven equipment are suitable for operation throughout the speed range
provided by the drive. The drive can be adjusted to operate the motor at
speeds above and below the speed provided by connecting the motor directly
to the power line.
• Do not activate automatic fault reset functions of the Standard Control Program
if dangerous situations can occur. When activated, these functions will reset
the drive and resume operation after a fault.
• Do not control the motor with the disconnecting device (means); instead, use
the control panel keys and , or commands via the I/O board of the drive.
The maximum allowed number of charging cycles of the DC capacitors (i.e.
power-ups by applying power) is five in ten minutes.
• Do not use the Prevention of unexpected start-up function (option +Q950) for
stopping the drive when the inverter unit(s) is running. Give a Stop command
instead.
• The Safe torque off function (option +Q968) can be used for stopping the drive
in emergency stop situations. In the normal operating mode, use the Stop
command instead.
Note:
• If an external source for start command is selected and it is ON, the drive (with
Standard Control Program) will start immediately after fault reset unless the
drive is configured for 3-wire (a pulse) start/stop.
• When the control location is not set to Local (L not shown in the status row of
the display), the stop key on the control panel will not stop the drive. To stop
the drive using the control panel, press the LOC/REM key and then the stop
key .
Safety instructions
12
Permanent magnet motor drives

These are additional warnings concerning permanent magnet motor drives.
WARNING! Do not work on the drive when the permanent magnet motor is rotating.
Also when the supply power is switched off, a rotating permanent magnet motor
feeds power to the intermediate circuit of the drive and also the supply connections
become live (even when the inverter is stopped!).
Installation and maintenance work

• Disconnect the motor from the drive with a safety switch
and additionally, if possible,
• lock the motor shaft and ground the motor connection terminals temporarily by
connecting them together as well as to the PE.
Operation
Do not run the motor above the rated speed. Motor overspeed leads to overvoltage
which may result in explosion of the capacitors in the intermediate circuit of the drive.
Inverter control program

Controlling a permanent magnet motor is only allowed using the ACS800 Permanent
Magnet Synchronous Motor Drive Application Program.
Safety instructions
13
Table of contents
Safety instructions
What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Usage of warnings and notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation and maintenance work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Fibre optic cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Permanent magnet motor drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Installation and maintenance work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Inverter control program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Table of contents
About this manual

What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Target audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Common chapters for multiple products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Categorization according to the frame size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Installation and commissioning flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Inquiries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Terms and abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
The ACS800-17
The ACS800-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Cabinet line-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Frame R6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Frame R7i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Frame R8i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Swing-out frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Cabling direction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Single-line circuit diagram of the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Operation principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Line-side converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
AC voltage and current waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Motor-side converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Frame R6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Frame R7 and up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Control interfaces of the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Table of contents
14
Door switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Main switch-disconnector (Q1 in frame size R6 to R8i) . . . . . . . . . . . . . . . . . . . . . . . . .39
Air circuit breaker (Q1 in frame size 2×R8i and up) . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Auxiliary power switch (Q100 in frame size 2×R8i and up) . . . . . . . . . . . . . . . . . . . . . .39
Earthing switch (Q9 in frame size 2×R8i and up) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Other door switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
To control the supply unit… . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
To control the inverter unit… . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Fieldbus control of the line-side converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Block diagram: reference select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Type code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Frame sizes R6, R7i and R8i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Frame sizes 2×R8i to 6×R8i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Mechanical installation
What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Required tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Moving the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
…by crane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
…by fork-lift or pallet truck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
…on rollers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Laying the unit on its back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Final placement of the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Before installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Delivery check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Installation procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Fastening the cabinet to the floor (Non-marine units) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Clamping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Holes inside the cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Fastening the unit to the floor and wall (Marine units) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Joining the shipping splits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Connecting the DC busbars and the PE busbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
DC busbars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
PE busbar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Cable conduit in the floor below the cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Cooling air intake through bottom of cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Electric welding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Planning the electrical installation

What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Motor selection and compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Protecting the motor insulation and bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Requirements table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Table of contents
15
Permanent magnet synchronous motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Thermal overload and short-circuit protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Supply (AC line) cable short-circuit protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Earth fault (Ground fault) protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Emergency stop devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Prevention of unexpected start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Safe torque off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
ATEX-certified thermal motor protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Selecting the power cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
General rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Alternative power cable types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Motor cable shield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Additional US requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Conduit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Armored cable / shielded power cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Power factor compensation capacitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Equipment connected to the motor cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Installation of safety switches, contactors, connection boxes, etc. . . . . . . . . . . . . . . . . . . . . 75
Bypass connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Before opening an output contactor (in DTC motor control mode) . . . . . . . . . . . . . . . . . . . . 76
Relay output contacts and inductive loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Selecting the control cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Relay cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Control panel cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Coaxial cable (for use with Advant Controllers AC 80/AC 800) . . . . . . . . . . . . . . . . . . . . . . . 77
Connection of a motor temperature sensor to the drive I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Installation sites above 2000 metres (6562 feet) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Routing the cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Control cable ducts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Electrical installation
Option coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Before installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Checking the insulation of the assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Supply cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Motor and motor cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
IT (ungrounded) systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
EMC filter +E202 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
EMC filter +E200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
EMC filter +E210 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Input power connection – Frame R6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Connection procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Input power connection – Frame R7i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Connection procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Table of contents
16
Input power connection – Frame R8i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86

Connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Connection procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Input power connection – Frame 2×R8i and up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
Grounding of shielded single-core input cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
Motor connection – Frame R6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
Motor connection – Frame R7i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
Motor connection – Frame R8i units without option +E202 or +H359 . . . . . . . . . . . . . . . . . . . . . . .90
Motor connection – Frame R8i with option +E202 but without +H359 . . . . . . . . . . . . . . . . . . . . . . .91
Output busbars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
Motor connection – Units with common motor terminal cubicle (+H359) . . . . . . . . . . . . . . . . . . . . .93
Motor connection – Frame 2×R8i and up without common motor terminal cubicle . . . . . . . . . . . . .94
Output busbars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
Control connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
Drive control connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
Supply unit control connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
Connection procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .96
Installation of optional modules and PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
Cabling of I/O and fieldbus modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
Cabling of pulse encoder interface module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
Fibre optic links . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
Tap settings of the auxiliary voltage transformer (Frame R8i and up) . . . . . . . . . . . . . . . . . . . . . . .99
Motor control and I/O board (RMIO)

What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
To which products this chapter applies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
Note on cabinet-installed ACS800 drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
Note on terminal labelling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
External control connections (non-US) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
External control connections (US) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103
RMIO board specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104
Analogue inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104
Constant voltage output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104
Auxiliary power output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104
Analogue outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104
Table of contents
17
Digital inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Relay outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
DDCS fibre optic link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
24 V DC power input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Installation checklist and start-up

What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Installation checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Start-up procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Basic checks with no voltage connected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Connecting voltage to input terminals and auxiliary circuit . . . . . . . . . . . . . . . . . . . . . . . . . 108
Starting the supply unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Checks with the supply unit running . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Supply unit (line-side converter) program set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Inverter control program set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
ACS800-17-specific parameters in the IGBT Supply Control Program . . . . . . . . . . . . . . . . . . . . . 110
Terms and abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
On-load checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Default values of parameters with the ACS800-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
ACS800-17-specific parameters in the inverter control program . . . . . . . . . . . . . . . . . . . . . . . . . 113
Terms and abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Actual signals and parameters of the supply unit control program visible also in
the inverter control program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Maintenance
Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Maintenance intervals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Reduced run capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Checking and replacing the air filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Quick connectors (Frame R8i and up) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Cooling fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Supply/Inverter module cooling fan replacement (Frame R6) . . . . . . . . . . . . . . . . . . . . . . . 118
Supply/Inverter module cooling fan replacement (Frame R7i) . . . . . . . . . . . . . . . . . . . . . . . 119
LCL filter module cooling fan replacement (Frame R7i) . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Supply and inverter module cooling fan replacement (Frame R8i and up) . . . . . . . . . . . . . 121
Module fan replacement procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
LCL filter cooling fan replacement (Frame R8i and up) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
LCL filter fan replacement procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Cabinet fan replacement (Frame R6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Cabinet fan replacement (Frame R8i with IP21-42) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Cabinet fan replacement (Frame 2xR8i and up with IP21-42) . . . . . . . . . . . . . . . . . . . . . . . 124
Cabinet fan replacement (Frame R8i and up with IP54) . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Heatsinks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Capacitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Reforming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Capacitor replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Table of contents
18
Power module replacement (Frame R8i and up) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127

Extracting the module from the cubicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128
Inserting the module into the cubicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131
Fault tracing
Faults and warnings displayed by the CDP-312R Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . .133
Warning/Fault message from unit not being monitored by control panel . . . . . . . . . . . . . . .133
Conflicting ID numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .133
LEDs of the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134
Technical data
What this chapter contains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .135
IEC ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .135
Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136
Derating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136
Temperature derating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137
Altitude derating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137
NEMA ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .138
Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .139
ACS800-17 frame sizes and power module types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .139
AC fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140
DC fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .142
Input power connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .143
Motor connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .145
Efficiency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148
Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148
Degrees of protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148
Ambient conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .148
Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .149
Tightening torques for power connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150
Applicable standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .150
CE marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .151
Compliance with the European Low Voltage Directive . . . . . . . . . . . . . . . . . . . . . . . . . . . . .151
Compliance with the European EMC Directive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .151
Compliance with the European Machinery directive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .151
Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .152
Compliance with EN 61800-3:2004 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .154
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .154
Category C2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .154
Category C3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .154
Category C4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .155
“C-tick” marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .155
Table of contents
19
Dimensions
Cabinet line-ups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
R6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
R7i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
R8i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
2×R8i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
3×R8i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
4×R8i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
5×R8i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
6×R8i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Frame R6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Frame R7i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
Frame R7i with +E202/+E205/+H359 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Frame R7i, marine construction (+C121) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
Frame R8i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
Frame R8i with +E202/+H359 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
Frame 2×R8i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
Frame 3×R8i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196
Frame 4×R8i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
Frame 5×R8i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 208
Frame 6×R8i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220
Further information
Product and service inquiries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235
Product training . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235
Providing feedback on ABB Drives manuals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235
Document library on the Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235
Table of contents
20
Table of contents
21
About this manual

This chapter describes the intended audience and contents of the manual. It
contains a flowchart of steps in checking the delivery, installing and commissioning
the drive. The flowchart refers to chapters/sections in this manual and other
manuals.
Target audience
This manual is intended for people who plan the installation, install, commission, use
and service the drive. Read the manual before working on the drive. The reader is
expected to know the fundamentals of electricity, wiring, electrical components and
electrical schematic symbols.
The manual is written for readers worldwide. Both SI and imperial units are shown.
Special US instructions for installations within the United States that must be
installed per the National Electrical Code and local codes are marked with (US).
Common chapters for multiple products

Some chapters in this manual apply to several products including the ACS800-17.
Other product types may be mentioned in these chapters.
Categorization according to the frame size

Some instructions, technical data and dimensional drawings which concern only
certain drive frame sizes are marked with the symbol of the frame size (such as
“2×R8i”, etc.). The frame size is not marked on the drive designation label. To
identify the frame size of your drive, see the rating tables in chapter Technical data.
About this manual

22
Contents
The chapters of this manual are briefly described below.
Safety instructions gives safety instructions for the installation, commissioning,
operation and maintenance of the drive.
About this manual introduces this manual.
The ACS800-17 describes the drive.
Mechanical installation instructs how to move, place and mount the drive.
Planning the electrical installation provides advice on motor and cable selection, the
protective functions of the drive, and cable routing.
Electrical installation describes the cabling and wiring of the drive.
Motor control and I/O board (RMIO) shows external control connections to the motor
control and I/O board and its specifications.
Installation checklist and start-up helps in checking the mechanical and electrical
installation of the drive.
Maintenance contains preventive maintenance instructions.
Fault tracing contains troubleshooting instructions.
Technical data contains the technical specifications of the drive, e.g. ratings, frame
sizes and technical requirements, provisions for fulfilling the requirements for CE
and other markings and warranty policy.
Dimensions contains information on the dimensions of the drive.
About this manual

23
Installation and commissioning flowchart
Task See
Plan the installation. Technical data

Check the ambient conditions, ratings, required Planning the electrical installation
cooling air flow, input power connection, compatibility Option manuals (if optional equipment is
of the motor, motor connection, and other technical included)
data.
Select the cables.
Unpack and check the units. Mechanical installation

Check the type code indicated by the type The ACS800-17
designation label with the original order. For instructions on how to disconnect the EMC/
If the drive is about to be connected to an IT RFI filtering, contact your local ABB
(ungrounded) system: representative.
• check that the drive is not equipped with EMC/RFI If the converter has been non-operational for
filtering +E202 more than one year, the converter DC link
• if the drive is of frame size R6, check that the drive capacitors need to be reformed. Contact your
is not equipped with EMC/RFI filtering +E200. local ABB representative for more information.
Check that all necessary optional modules and
equipment are present and correct.
Only intact units may be started up.
Check the installation site. Mechanical installation, Technical data
Route the cables. Planning the electrical installation: Routing the

cables
Mount the cabinet line-up. Mechanical installation
Check the insulation of the motor and the motor Electrical installation: Checking the insulation of
cable. the assembly
Connect the power cables. Connect the control and Mechanical installation, Planning the electrical
the auxiliary control cables. installation, Electrical installation
Check the installation. Installation checklist and start-up
Commission the drive. Installation checklist and start-up, The ACS800-

17, and appropriate firmware manual
About this manual

24
Inquiries
Address any inquiries about the product to the local ABB representative, quoting the
type code and serial number of the unit. If the local ABB representative cannot be
contacted, address inquiries to ABB Oy, AC Drives, PO Box 184, 00381 Helsinki,
Finland.
Terms and abbreviations

Term/Abbreviation Explanation
AGPS Gate driver power supply board. An optional board within drives, used to
implement the Prevention of unexpected start-up function.
APBU Type of optical branching unit used for connecting parallel-connected

converter modules to the RDCU.
ASTO An optional board within drives, used to implement the Safe torque off
function.
CMF Common mode filtering.
DDCS Distributed Drives Communication System; a protocol used in optical fibre

communication inside and between ABB drives.
Drive unit See Motor-side converter.
EMC Electromagnetic Compatibility.
Four-quadrant Operation of a machine as a motor or generator in quadrants I, II, III and

operation IV as shown below. In quadrants I and III, the machine operates as a
motor, whereas in quadrants II and IV it operates as a generator
(regenerative braking).
Torque
II I
Speed
III IV
Frame (size) Relates to the construction type of the component in question. For
example, several drive types with different power ratings may have the
same basic construction, and this term is used in reference to all those
drive types.
With the ACS800-17, the frame size of the drive indicates the quantity and
frame size of the inverter modules, e.g. “2×R8i”.
To determine the frame size of a drive type, see the rating tables in
chapter Technical data.
IGBT Insulated Gate Bipolar Transistor; a voltage-controlled semiconductor type

widely used in inverters because of their easy controllability and high
switching frequency.
About this manual

25
Term/Abbreviation Explanation
IGBT supply module Bidirectional IGBT bridge and related components enclosed inside a metal
frame or enclosure. Intended for cabinet installation. Used as the supply
module in regenerative and low-harmonic drives.
IGBT supply unit (ISU) See Line-side converter.
Inverter module Inverter bridge, related components and drive DC link capacitors enclosed
inside a metal frame or enclosure. Intended for cabinet installation.
Inverter unit (INU) See Motor-side converter.
Line-side converter A converter that is connected to the supply network and is capable of
transferring energy from the network to the DC link of the drive, or from
the DC link of the drive to the network. With ACS800-17 drives of frame
size R8i and above, the line-side converter is also called the (IGBT)
supply unit or the ISU.
Motor-side converter A converter that is connected to the motor and controls the motor
operation. With ACS800-17 drives of frame size R8i and above, the
motor-side converter is also called the inverter unit or INU.
PPCS Power Plate Communication System; a protocol used in the optical fibre
link that controls the output semiconductors of an inverter module.
RDCU Drive control unit. The RDCU is a separate unit consisting of an RMIO
board built in a plastic housing.
RFI Radio-Frequency Interference.
RMIO Motor control and I/O board. Contains the principal inputs and outputs of
the drive. The RMIO is contained within the RDCU drive control unit.
THD Total Harmonic Distortion.
About this manual

26
About this manual

27
The ACS800-17

This chapter describes the construction of the drive in short.
The ACS800-17
The ACS800-17 is a four-quadrant, cabinet-mounted drive for controlling
asynchronous AC induction motors and generators, and permanent magnet
synchronous motors and generators.
Cabinet line-up
The drive consists of one or more cubicles that contain the supply and motor
terminals, 1 to 6 IGBT supply module(s) forming the line-side converter, 1 to 6
inverter modules forming the motor-side converter, and optional equipment. (Frame
R6 drives employ an integrated supply/inverter module.) The actual arrangement of
the cubicles varies from type to type and the selected options. See also chapter
Dimensions for the different line-up variations.
The ACS800-17
28
Frame R6
The picture below shows the main components of a frame R6 drive with the door
open, and with the swing-out frame closed (left) and open (right).
3 3
No. Description
1 Swing-out frame (see page 31)
12 12 2 Cable entries for power and control cables (bottom
cable entry/exit models)
3 Cable entries for power and control cables (top cable
8 10 8 10 entry/exit models)
4 Switch fuse
4 4
5 Auxiliary voltage transformer
6 Integrated line-side/motor-side converter module
7 Input terminals (bottom cable entry/exit models)
8 Input terminals (top cable entry/exit models)
9 Output terminals (bottom cable entry/exit models)
10 Output terminals (top cable entry/exit models)
6 11 Control unit (RDCU) for motor-side converter
12 Cabinet cooling fan
11
1
7 9
5 5
2 2
The ACS800-17
29
Frame R7i
The picture below shows the main components of a frame R7i drive with the door
and the swing-out frame open.
No. Description
1 Swing-out frame (see page 31) (not shown). The drive
control units for both converter modules are installed on
the swing-out frame.
2 Cable entries for power and control cables (bottom
cable entry/exit models)
8 6 1 3 Cable entries for power and control cables (top cable
entry/exit models)
4 Switch fuse
5 Auxiliary voltage transformer
6 Line-side converter module
10 7 LCL filter
8 Motor-side converter module
9 Input terminals
10 Output terminals
9 4
5 7
The ACS800-17
30
Frame R8i
The picture below shows the main components of a frame R8i drive with the doors
open.
No. Description
1 Swing-out frame (see picture on page 31)
2 Supply unit controller (RDCU)
4 3 Inverter unit controller (RDCU)
5 4 Switch-disconnector*
8 5 Input contactor*
6 LCL filter
7 IGBT supply module
2
8 Intermediate DC link
3
9 Inverter module
6 7 9 10 Cooling fan for LCL filter
11 Cooling fan for IGBT supply module
12 Cooling fan for inverter module
13 Auxiliary voltage transformer (accessible by opening
14 the swing-out frame)
1 14 Auxiliary voltage circuitry (relays etc.)
13 *In larger drives, an air circuit breaker is used instead of the
switch-disconnector/contactor combination.
10 11 12
The ACS800-17
31
Swing-out frame
The swing-out frame provides space for the control circuitry of the drive as well as
optional electrical equipment. The frame can be opened by removing the locking
screws (arrowed in the picture below) and moving the swing-out frame aside.
Depending on the frame size of the drive, the actual equipment of the drive may
differ from what is depicted.
Remove screws (arrowed) to Swing-out frame open

open swing-out frame
Drive control unit

(RDCU) with I/O
terminal blocks
Space for optional

terminal block X2
I/O cable entries into
Terminal block X1
swing-out frame
Mounting rails for

additional equipment
The ACS800-17
32
The following is a generic device layout diagram for the swing-out frame (drive frame
size R8i). The diagram is also attached to the inside of the cubicle door, with
installed devices marked. Refer to the circuit diagrams delivered with the drive for
device designations.
The ACS800-17
33
Cabling direction
The drawings below show the available cabling directions of the drive.
Frame size R6
6 3 Description
2 5 1 Input/Motor output – Bottom entry
IP21-42 IP54
2 Input/Motor output – Top entry (IP21-42)
3 Input/Motor output – Top entry (IP54)
4 Signal cable input/output – Bottom entry
5 Signal cable input/output – Top entry (IP21-42)
6 Signal cable input/output – Top entry (IP54)
1 4 1 4
Frame size R7i
Description
2 4 1 Input/Motor output – Bottom entry
2 Input/Motor output – Top entry
4 Signal cable input/output – Top entry
1 3
The ACS800-17
34
Frame size R8i
Description
2
10 11
4 6 8 A Input/output cubicle
B Supply and inverter unit cubicle
C Common motor terminal cubicle*
1 Standard input (bottom entry)

2 Standard input (top entry)
3 Standard output (bottom exit)
A B C
4 Standard output (top exit)
5 Optional output (bottom exit, 1st Environment)
6 Optional output (top exit, 1st Environment); additional depth 130 mm
7 Motor output – Bottom exit with common motor terminal cubicle*
8 Motor output – Top exit with common motor terminal cubicle*
10 Signal cable input/output – Top entry (IP54)
3 5 7
9 11 Signal cable input/output – Top entry (IP21-42)
1
*With EMC/RFI filtering for 1st Environment (+E202) only
Frame size 2×R8i and up
2
10 Description
4 6
A Auxiliary control cubicle
B Incoming cubicle
C Inverter unit cubicle
D Common motor terminal cubicle (optional)
1 Standard input (bottom entry)

2 Standard input (top entry)
3 Standard output (bottom exit); at each inverter module
4 Standard output (top exit); at each inverter module
A B C D
5 Motor output – Bottom exit with common motor terminal cubicle
(optional)
6 Motor output – Top exit with common motor terminal cubicle
(optional)
3 5 9 Signal cable input/output – Bottom entry

9
1 10 Signal cable input/output – Top entry
The ACS800-17
35
Single-line circuit diagram of the drive

Note: This diagram represents a frame 2×R8i drive without a common motor
terminal cubicle.
DC bus
Ground fault supervision

M
Motor fan supply

230/115 V AC
400 V AC
400 V AC
3~
M
M
400 V AC
M
400 V AC
Charging
M
circuit
M
400 V AC
230/400 V AC
Main
Supply
The ACS800-17
36
Operation principle
The line-side and motor-side converters have their own RDCU control units and
control programs. The parameters of each program can be viewed and changed
using one control panel. The converter to be controlled can be selected using the
control panel; see section Controls below.
Line-side converter
The line-side converter rectifies three-phase AC current to direct current for the
intermediate DC link of the drive. The intermediate DC link is further supplying the
motor-side converter that runs the motor.
The LCL filter suppresses the AC voltage distortion and current harmonics.
The IGBT supply module is a four-quadrant switching-mode converter, i.e. the power
flow through the converter is reversible. By default, the converter controls the DC link
voltage to the peak value of the line-to-line voltage. The DC voltage reference can be
set also higher by a parameter. The control of the IGBT power semiconductors is
based on the Direct Torque Control (DTC) method also used in the motor control of
the drive. Two line currents and the DC link voltage are measured and used for the
control.
AC fuses LCL filter IGBT supply module
AC input Intermediate
DC link
AC voltage and current waveforms

The AC current is sinusoidal at a unity power factor. The IGBT supply unit does not
generate characteristic current or voltage overtones like a traditional 6- or 12-pulse
bridge does.
The ACS800-17
37
Motor-side converter
The motor control is based on the Direct Torque Control (DTC) method. Two phase
currents and DC link voltage are measured and used for the control. The third phase
control is measured for earth fault (ground fault) protection.
Frame R6
The motor-side converter is controlled by an RDCU drive control unit located in the
integrated line-side/converter-side module.
Frame R7 and up
The motor-side converter is controlled by an RDCU drive control unit located in the
swing-out frame of the cabinet. The RDCU is connected to the inverter module(s) by
a fibre optic link, distributed through an optical branching unit. In the inverter
modules, the optic link connects to the AINT board, the terminals of which are
accessible through a hole on the front panel of the module.
The ACS800-17
38
Parameter setting and diagnostics through
CDP 312R Control Panel (and related
accessories).
Note: By default, the Control Panel of the
Controls
drive is set to control the inverter unit.
The ACS800-17
Drive Control Unit Drive Control Unit
(RDCU) (RDCU)
Motor Control Motor Control Optional module 1: I/O

and I/O Board and I/O Board extension (RAIO, RDIO),
pulse encoder interface
(RMIO) (RMIO)
(RTAC), or fieldbus
adapter (e.g. RMBA,
RDNA, RPBA)
Control interfaces of the drive
External control via

Optional module 2: I/O
analogue/digital
1 RESET G extension (RAIO, RDIO)
0 S E R ENC inputs and outputs
M
E
Y
or pulse encoder interface
(RTAC)
S TO P
RDCO RDCO Optional module 3:

Supply unit control circuitry CH0 CH1 DDCS communication
including door switches, Fibre optic link module (RDCO-01,
charging circuit control, RDCO-02 or RDCO-03)
main contactor control, etc.
Input power
= ~ To motor
~ =
Supply unit Inverter unit
The following diagram shows the control interfaces and I/O options of the drive.
39
Door switches
Main switch-disconnector (Q1 in frame size R6 to R8i)
The switch-disconnector handle switches the main and auxiliary voltages to the drive
on and off.
Air circuit breaker (Q1 in frame size 2×R8i and up)
The air circuit breaker controls the main supply voltage (phases L1, L2 and L3). For
more information on using the breaker, refer to its manual.
WARNING! Opening the air circuit breaker will not switch off the auxiliary voltages of
the drive.
Auxiliary power switch (Q100 in frame size 2×R8i and up)

The auxiliary power switch controls all auxiliary voltages in the cabinet including the
DC link charging circuit. The auxiliary voltage switch must be closed before the drive
can be started.
Earthing switch (Q9 in frame size 2×R8i and up)
When closed, the optional earthing switch connects the supply phases L1, L2 and L3
to PE. The switch is interlocked so that it cannot be closed when the drive is
powered. Likewise, the drive will not start when the earthing switch is closed.
Other door switches
These switches are only installed if the drive is equipped with the optional
emergency stop function.
Start switch 1 Emergency stop button

G
0 = Cooling fans are disabled. (Other 0 S ER EN
EM
auxiliary voltages are on.)

CY
0 ⇒ S = Starts the cooling fans,

closes the main contactor and starts
the supply unit.
1 ⇒ 0 = Switches off the drive and
opens the main contactor. Other STO P
auxiliary voltages are on.
Reset button RESET

Resets an emergency stop, after
which the supply unit can be started
using the start switch.
(Drive faults are reset via the drive
control panel or serial
communication)
The ACS800-17
40
Control panel
A control panel (type CDP-312R) is installed on the door of the drive. The CDP-312R
is the user interface of the supply unit (line-side converter) and the inverter unit
(motor-side converter) of the drive, providing the essential controls such as Start/
Stop/Direction/Reset/Reference, and the parameter settings for the units’ control
programs. More information on using the panel can be found in the Firmware Manual
delivered with the drive.
The control panel is wired to both the supply unit and the inverter unit using a
Y-splitter. The unit that is currently being controlled is indicated by the drive name on
the drive display; the suffix “MR” denotes inverter unit, “LR” denotes supply unit. The
control is switched between the units as follows:
To control the supply unit…
Step Action Press… Display (example)
1. To enter the Drive Selection Mode ACS 800 0490_3MR

Note: In local control mode, the motor-side converter trips DRIVE
if parameter 30.02 PANEL LOSS is set to FAULT. Refer to ASXR7xxx

ID-NUMBER 1
the appropriate application program firmware manual.
2. To scroll to ID number 2 ISU 800 0490_3LR
IXXR7xxx
ID-NUMBER 2
3. To verify the change to the line-side converter and display 2 -> 380.0 V
the warning or fault text ACT ISU 800 0490_3LR
*** FAULT ***
DC OVERVOLT (3210)
WARNING! The drive does not stop by pressing the control panel Stop key in local
control mode.
To control the inverter unit…

Step Action Press… Display (example)
1. To enter the Drive Section Mode ISU 800 0490_3LR

DRIVE
IXXR7xxx
ID-NUMBER 2
2. To scroll to ID number 1 ACS 800 0490_3MR
ASXR7xxx
ID-NUMBER 1
3. To verify the change to the motor-side converter 1 L -> 0.0 rpm I

ACT FREQ 0.00 Hz
CURRENT 0.00 A
POWER 0.00 %
The ACS800-17
41
Fieldbus control of the line-side converter

Fieldbus control of the line-side converter is performed via the motor-side converter
RMIO board as shown in the block diagram below.
Block diagram: reference select
The figure below shows the parameters for DC and reactive power reference
selection in the ACS800 Standard Control Program. AMC table contains actual
values and parameters of the line converter.
11.02 Q REF SELECT
Inverter RMIO Line converter RMIO board PARAM 24.01

board
98.02 COMM. MODULE AI1
= INU COM LIM 24.03 Q POWER REF2 SEL AI2 24.01
Dataset 121 (CH1) AI3

Dataset 121 (CH0) Q POWER REF
MCW MCW (fixed) PERCENT
kVAr + PARAM 24.02
95.06 LCU Q PW REF Q-REF(fixed) 24.02 +
PHI
95.07 LCU DC REF DC REF(fixed) COSPHI
Dataset 122 (CH1) Dataset 122 (CH0)

MSW MSW (fixed)
24.04
9.12 LCU ACT SIGNAL 1 106 (value)
9.13 LCU ACT SIGNAL 2 110 (value)
11.01 DC REF SELECT
Dataset 123 (CH1) Dataset 123 (CH0) PARAM 23.01

95.08 LCU PAR1 SEL 106
95.09 LCU PAR2 SEL DC VOLT REF
110 AMC AI1
table AI2 23.01
AI3
FIELD BUS
MCW = Main Control Word

MSW = Main Status Word
The ACS800-17
42
Type code
The type code of the drive is indicated on the type designation label, attached on the
cabinet door. The type code contains information on the specifications and
configuration of the drive. The first digits from left express the basic configuration
(e.g. ACS800-17-0490-3). The optional selections are given thereafter, separated by
+ signs (e.g. +E202). The main selections are described below.
Note: The information below is for quick reference only and does not contain all
conditions and details. For more information, refer to ACS800 Ordering Information
(code: 64556568), available through ABB representatives.
Frame sizes R6, R7i and R8i
Selection Alternatives
Product series ACS800 product series
Type 17 = cabinet-mounted
Default configuration: IP21 (UL Type 1); main switch/disconnector with aR-
type AC fuses; line contactor (optional for frame R6); 230 V AC auxiliary
voltage; RDCO-03 DDCS Communication Option; CDP-312R Control Panel;
EMC/RFI filtering for 2nd Environment (except frame R6); common mode
filtering (except frame R6); Standard Control Program; bottom entry/exit of
cables; coated circuit boards; set of English manuals.
Size Refer to Technical data: IEC ratings.
Voltage range 3 = 380/400/415 V AC
(nominal rating in bold) 5 = 380/400/415/440/460/480/500 V AC
7 = 525/575/600/690 V AC
+ options
I/O options Refer to ACS800 Ordering Information (code: 64556568 [English]).
Fieldbus adapter
Control program
Degree of protection B053 = IP22 (UL Type 1)
B054 = IP42 (UL Type 1)
B055 = IP54 (UL Type 12)
B059 = IP54R with connection to air outlet duct
Construction C121 = Marine construction (reinforced mechanical parts and fastening,
marking of conductors [A1], door handles, self-extinctive materials)
C129 = UL Listed
C134 = CSA Approved
Filters E200 = EMC/RFI filtering, Cat. C3, 2nd Environment, TN (grounded) system
(frame R6 only)
E202 = EMC/RFI filtering, Cat. C2, 1st Environment, TN (grounded) system.
Not available for 690 V.
E205 = du/dt filtering
E206 = Sine filter (frames R7i and R8i only) – Not available with +C121 or
+C129.
The ACS800-17
43
Cabling H350 = Bottom entry (with +C129)
H351 = Top entry
H352 = Bottom exit (with +C129)
H353 = Top exit
H356 = DC cable connection busbars
H358 = US/UK gland/conduit plate (steel, 3 mm)
H359 = Common motor terminal cubicle – Frame R8i with +E202 only
H365 = US/UK gland/conduit plate (brass, 6 mm)
Auxiliary voltage G304 = 115 V AC – Standard with +C129 and +C134
Cabinet options G300 = Cabinet heaters (external supply) – Not available with +C129 or
+C134
G307 = Input terminals for external UPS-backed auxiliary voltage
G313 = Output for motor heater (external supply)
G330 = Halogen-free wiring and materials – Not available with +C129 or
+C134
G338 = Wire marking class A1
G341 = Wire marking class B1
G342 = Wire marking class C1
Language of manuals Rxxx
Refer to ACS800 Ordering Information (code: 64556568 [English]).
Starter of auxiliary M600 = 1 … 1.6 A (1 pc)
motor fan M601 = 1.6 … 2.5 A (1 pc)
M602 = 2.5 … 4 A (1 pc)
M603 = 4 … 6.3 A (1 pc)
M604 = 6.3 … 10 A (1 pc) – Not for frame R6
M605 = 10 … 16 A (1 pc) – Not for frame R6
Safety features Q950 = Prevention of unexpected start-up (Category 3)
Q951 = Emergency stop, Category 0 (with opening main contactor/breaker)
Q952 = Emergency stop, Category 1 (with opening main contactor/breaker)
Q954 = Earth fault monitoring for IT (ungrounded) system
Q963 = Emergency stop, Category 0 (without opening main contactor/
breaker)
Q964 = Emergency stop, Category 1 (without opening main contactor/
breaker)
Q968 = Safe torque off (STO) with a safety relay
Q971 = ATEX-certified safety function
Special P902 = Customised (specified in Technical appendix on ordering)
P904 = Extended warranty
P913 = Special colour (specified in Technical appendix on ordering)
Frame sizes 2×R8i to 6×R8i
Product series ACS800 product series
Type 17 = cabinet-mounted
Default configuration: IP21 (UL Type 1); air circuit breaker; 230 V AC
auxiliary voltage; RDCO-03 DDCS Communication Option; CDP-312R
Control Panel; EMC/RFI filtering for 2nd Environment; du/dt filtering; common
mode filtering; Standard Control Program; bottom entry/exit of cables; coated
circuit boards; set of English manuals.
Size Refer to Technical data: IEC ratings.
The ACS800-17
44
Voltage range 3 = 380/400/415 V AC
(nominal rating in bold) 5 = 380/400/415/440/460/480/500 V AC
7 = 525/575/600/690 V AC
+ options
I/O options Refer to ACS800 Ordering Information (code: 64556568 [English]).
Fieldbus adapter
Control program
Degree of protection B053 = IP22 (UL Type 1)
B054 = IP42 (UL Type 1)
B055 = IP54 (UL Type 12)
B059 = IP54R with connection to air outlet duct
Construction C121 = Marine construction (reinforced mechanical parts and fastening,
marking of conductors [A1], door handles, self-extinctive materials)
C129 = UL Listed
C134 = CSA Approved
Filters E202 = EMC/RFI filtering, Cat. C2, 1st Environment, TN (grounded) system.
Note: EMC/RFI filtering for 2nd Environment (+E210) is standard equipment.
E206 = Sine filter – Not available with +C121 or +C129.
Line options F259 = Earthing switch – Not available with +C129
Cabling H350 = Bottom entry (with +C129)
H351 = Top entry
H352 = Bottom exit (with +C129)
H353 = Top exit
H356 = DC cable connection busbars
H358 = US/UK gland/conduit plate (steel, 3 mm)
H359 = Common motor terminal cubicle
H365 = US/UK gland/conduit plate (brass, 6 mm)
Auxiliary voltage G304 = 115 V AC
Cabinet options G300 = Cabinet heaters (external supply) – Not available with +C134
G307 = Input terminals for external UPS-backed auxiliary voltage
G313 = Output for motor heater (external supply)
G317 = Busbar supply conductors
G330 = Halogen-free wiring and materials – Not available with +C129 or
+C134
G341 = Wire marking class B1
G342 = Wire marking class C1
Language of manuals Rxxx
Refer to ACS800 Ordering Information (code: 64556568 [English]).
Starter of auxiliary M602 = 2.5 … 4 A (1, 2 or 4 pcs)
motor fan M603 = 4 … 6.3 A (1, 2 or 4 pcs)
M604 = 6.3 … 10 A (1, 2 or 4 pcs)
M605 = 10 … 16 A (1 or 2 pcs)
M606 = 17 … 25 A (1 pc)
The ACS800-17
45
Safety features Q950 = Prevention of unexpected start-up (Category 3)
Q951 = Emergency Stop, Category 0 (with opening main contactor/breaker)
Q952 = Emergency Stop, Category 1 (with opening main contactor/breaker)
Q954 = Earth fault monitoring for IT (ungrounded) system
Q963 = Emergency Stop, Category 0 (without opening main contactor/
breaker)
Q964 = Emergency Stop, Category 1 (without opening main contactor/
breaker)
Q968 = Safe torque off (STO) with a safety relay
Q971 = ATEX-certified safety function
Special P902 = Customised (specified in Technical appendix on ordering)
P904 = Extended warranty
P913 = Special colour (specified in Technical appendix on ordering)
The ACS800-17
46
The ACS800-17
47

This chapter describes the mechanical installation procedure of the drive.
General
See chapter Technical data for allowable operating conditions and requirements for
free space around the unit.
The unit should be installed in an upright vertical position.
The floor that the unit is installed on should be of non-flammable material, as
smooth as possible, and strong enough to support the weight of the unit. The floor
flatness must be checked with a spirit level before the installation of the cabinets into
their final position. The maximum allowed deviation from the surface level is 5 mm in
every 3 metres. The installation site should be levelled, if necessary, as the cabinet
is not equipped with adjustable feet.
The wall behind the unit should be of non-flammable material.
Provide the drive with the amount of fresh cooling air given in Technical data.
Note: Very wide cabinet line-ups (> 4200 mm) are delivered as shipping splits.
Required tools
The tools required for moving the unit to its final position, fastening it to the floor and
tightening the connections are listed below.
• crane, fork-lift or pallet truck (check load capacity!); iron bar, jack and rollers
• Pozidrive and Torx (2.5–6 mm) screwdrivers for the tightening of the frame
screws
• torque wrench
• set of wrenches or sockets for joining shipping splits.
48
Moving the unit
…by crane
Use the steel lifting lugs attached to the top of
the cabinet. Insert the lifting ropes or slings into
the holes of the lifting lugs.
The lifting lugs can be removed (not mandatory)
once the cabinet is in its final position. If the
lifting lugs are removed, the bolts must be
refastened to retain the degree of protection
of the cabinet.
IP54 units
Allowed minimum height of lifting ropes or slings
for IP54 units is 2 metres.
49
…by fork-lift or pallet truck
The centre of gravity may be quite high. Be therefore careful

when transporting the unit. Tilting the cabinets must be
avoided.
The units are to be moved only in the upright position.
If using a pallet truck, check its load capacity before
attempting to move the unit.
…on rollers
(Not allowed with Marine versions)
Remove the wooden bottom frame which is part
of the shipment.
Lay the unit on the rollers and move it carefully
until close to its final location.
Remove the rollers by lifting the unit with a
crane, fork-lift, pallet truck or jack as described
above.
Laying the unit on its back

If the cabinet needs to be laid on its back, it
Cabinet back panel Support must be supported from below beside the
cubicle seams as shown.
Notes:
• Transportation of a unit on its back is only
allowed if the unit is equipped for such
transportation at the factory.
• Never lay or transport a unit with sine filters
(i.e., with option code +E206) on its back.
• Never lay or transport an R8i or nxR8i unit on
its back.
50
Final placement of the unit

The cabinet can be moved into its final position with an
iron bar and a wooden piece at the bottom edge of the
cabinet. Care is to be taken to properly place the
wooden piece so as not to damage the cabinet frame.
51
Before installation
Delivery check
The drive delivery contains:
• drive cabinet line-up
• optional modules (if ordered) installed into the control rack at the factory
• ramp for extracting supply and inverter modules from the cabinet
• hardware manual
• appropriate firmware manuals and guides
• optional module manuals
• delivery documents.
Check that there are no signs of damage. Before attempting installation and
operation, check the information on the type designation label of the drive to verify
that the unit is of the correct type. The label includes an IEC and NEMA rating, C-UL
US, and CSA markings, a type code and a serial number, which allow individual
recognition of each unit. The first digit of the serial number refers to the
manufacturing plant. The next four digits refer to the unit’s manufacturing year and
week respectively. The remaining digits complete the serial number so that there are
no two units with the same serial number.
The type designation label is located on the supply unit door.
Each power module (i.e. supply and inverter module) is also individually labelled.
52
Installation procedure
1 See detailed instructions in the following few
pages.
(1) The cabinet can be installed with its back
against a wall, or back-to-back with another unit.
Fasten the unit (or first shipping split) to the floor
A with fastening clamps or through the holes inside
A
the cabinet. See section Fastening the cabinet to
the floor (Non-marine units).
With marine versions, fasten the unit (or first
shipping split) to the floor and wall/roof as
described in section Fastening the unit to the floor
and wall (Marine units).
Note: A clearance of 400 mm minimum above the
basic roof level of the cabinet (see inset on left) is
Top clearances required.
> 320 mm (12.3”)
for fan replace- Note: Leave some space at the left-hand and
ment
right-hand sides of the line-up (A) to allow the
> 400 mm > 400 mm
(15.75”) (15.75”) doors to open sufficiently.
IP22/42 IP54
Note: Any height adjustment must be done before
fastening the units or shipping splits together.
Height adjustment can be done by using metal
shims between the bottom frame and floor.
2
(2) Remove the lifting bars (if present). In marine
units, also replace the lifting lugs with L-profiles
(see below). Use the original bolts to block any
unused holes.
(3) If the line-up consists of shipping splits, fasten
the first split to the second. Each shipping split
includes a joining cubicle where the busbars
connect to the next split.
(4) Fasten the second shipping split to the floor.
(5) Join the DC busbars and the PE busbars.
(6) Repeat steps (2) to (5) for the remaining
3 shipping splits.
53
Fastening the cabinet to the floor (Non-marine units)

The cabinet is to be fastened to the floor by using clamps along the edge of the
cabinet bottom, or by bolting the cabinet to the floor through the holes inside.
Clamping
Insert the clamps into the twin slots along the front and rear edges of the cabinet
frame body and fasten them to the floor with a bolt. The recommended maximum
distance between the clamps is 800 mm (31.5”).
If there is not enough working space behind the cabinet for mounting, replace the
lifting lugs at the top with L-brackets (not included) and fasten the top of the cabinet
to the wall.
Slot detail, front view

(dimensions in millimetres)
Clamp dimensions (in millimetres) Distances between slots
Cubicle Distance in millimetres and (inches)

Width
(mm)
Cabinet frame
300 150 (5.9”)
400 250 (9.85”)
Cabinet frame 600 450 (17.7”)
700 550 (21.65”)
800 650 (25.6”)
L-bracket
M16 screw
Cabinet top
Fastening the cabinet at the top with

L-brackets (side view)
54
Holes inside the cabinet

The cabinet can be fastened to the floor using the fastening holes inside the cabinet,
if they are accessible. The recommended maximum distance between the fastening
points is 800 mm (31.5”).
If there is not enough working space behind the cabinet for mounting, replace the
lifting lugs at the top with L-brackets (not included) and fasten the top of the cabinet
to the wall.
Fastening holes inside the

cabinet (arrowed)
L-bracket
M16 screw
25 mm (0.985”)
Cabinet top

L-brackets (side view)
Distances between fastening holes Added width:

Bolt size: M10 to M12 (3/8” to 1/2”). Side panels of the cabinet: 15 mm (0.6”)
Back panel of the cabinet: 10 mm (0.4”)
Cubicle Distance between holes Gap between cubicles (mm):
Width Outer
Ø31 mm (1.22”) IP 20...42 IP 54
300 150 mm (5.9”)

400 250 (9.85”) ≈ 0.5 ≈1
(0.02”) (0.04”)
600 450 (17.7”)
700 550 (21.65”)
800 650 (25.6”)
55
Fastening the unit to the floor and wall (Marine units)

The unit must be fastened to the floor and roof (wall) as follows:
Bolt the unit to the floor through the holes in

1
each flat bar at the base of the cabinet using
M10 or M12 screws.
If there is not enough room behind the cabinet

2
for installation, clamp the rear ends of the flat
bars as shown in figure (2).
Fasten the top of the cabinet to the rear wall

3
and/or roof using brackets with a rubber
damper in between.
1
Use M10 or M12 screws; welding not

recommended (see section Electric
welding below).
2 3
L-bracket
Back panel of M16 bolt

Clamps cabinet
Flat bars at base of cabinet Cabinet

Clamping the cabinet to the brackets (side view)
floor at the back
56
Joining the shipping splits

The busbar systems and wiring harnesses of two shipping splits are joined in the
common motor terminal cubicle (if present) or a busbar joining cubicle. Special M6
screws for fastening the shipping splits together are enclosed in a plastic bag inside
the rightmost cubicle of the first shipping split. The threaded bushings are already
mounted on the post.
Threaded bushing
Procedure
Maximum tightening torque:

5 Nm (3 ft.-lbs)
7 7
• Fasten the front post of the joining section with 7 screws to the front frame post of
the next cubicle.
57
• Remove any intermediate or partitioning plates covering the rear posts of the
joining cubicle.
Partitioning
plate
Busbar joining Intermediate plate Back posts accessible

cubicle
• Fasten the rear post of the joining section with seven screws (below the busbar
joining part) to the rear post of the next cubicle.
• Replace all partitioning plates in the upper part of it after connecting the DC
busbars (see section Connecting the DC busbars and the PE busbar).
Connecting the DC busbars and the PE busbar

Horizontal main DC busbars and the PE busbar are connected from the front of the
joining cubicle. All necessary materials are located in the joining cubicle.
• Remove the front metal partitioning plate located in the busbar joining cubicle.
• Unscrew the bolts of the joint pieces.
• Connect the busbars with the joint pieces (see figure below). For aluminium
busbars, suitable anti-oxidant joint compound must be used to avoid corrosion
and to ensure good electrical connection. The oxide layer must be scrubbed off
from the joints before applying the compound.
• Refit all shrouds for safety of personnel.
58
DC busbars
The DC busbar connection is shown below.
1 1 Joint pieces
1
1
Tighten the bolts to

55–70 Nm (40–50 ft.-lbs.)
Side view of single busbar connection
PE busbar
The PE busbar runs continuously through the line-up near the floor at the back. The
connection is shown below. No separate nuts are needed.
Top view PE busbar
Tighten the screws to

55–70 Nm (40–50 ft.lbs.)
Shipping split A Shipping split B
59
Miscellaneous
Cable conduit in the floor below the cabinet

A cable conduit can be constructed below the 400 mm wide middle part of the
cabinet. The cabinet weight lies on the two 100 mm wide transverse sections which
the floor must carry.
Viewed from above Side view
With heavy
cabinets support
the structural C-
sections from
below.
This area can be used for a
cable conduit
Prevent the cooling air flow

from the cable conduit to
the cabinet by bottom
plates. To ensure the
degree of protection for the
cabinet use the original Cables
bottom plates delivered with
the unit. With user-defined
cable entries, take care of
the degree of protection, fire
protection and EMC
compliance.
60
Cooling air intake through bottom of cabinet

Units with air intake through the bottom of the cabinet (optional feature) are intended
for installation on an air duct in the floor. The required air inlets in the floor are as
listed below. Refer also to the dimensional drawings delivered with the unit.
• for DSU supply cubicles: w × 505 mm, where w equals cubicle width – 50 mm
• for ISU supply cubicles, inverter unit cubicles, control cubicles: w × 400 mm,
where w equals cubicle width – 50 mm
• w × 130 mm at the back of the cabinet line-up, where w equals the total width of
adjacent cubicles with air inlets. This area may or may not be consistent through
the width of the whole line-up.
Example
Input fuse cubicle Diode supply cubicle Inverter cubicle Common motor
Cubicle width: 400 mm Cubicle width: 700 mm Cubicle width: 600 mm terminal cubicle
Air inlet size: Air inlet size: Air inlet size: (No air inlet required)
350 × 400 mm 650 × 505 mm 550 × 400 mm
Notes:
• The plinth of the cabinet must be supported all round.
• The air duct must be able to supply a sufficient volume of cooling air. The
minimum air flow values are given in the Technical data section of the Hardware
Manual.
• The cubicles of diode supply units require a larger air inlet area than other
cubicles.
• Some cubicles (mainly those without active, heat-generating components) require
no air inlet.
61
Electric welding
It is not recommended to fasten the cabinet by welding.
Cabinets without flat bars at the base
• Connect the return conductor of the welding equipment to the cabinet frame at
the bottom within 0.5 metres of the welding point.
Cabinets with flat bars at the base
• Weld only the flat bar under the cabinet, never the cabinet frame itself.
• Clamp the welding electrode onto the flat bar about to be welded or onto the floor
within 0.5 metres of the welding point.
WARNING! If the welding return wire is connected improperly, the welding circuit
may damage electronic circuits in the cabinet. The thickness of the zinc coating of
the cabinet frame is 100 to 200 micrometres; on the flat bars the coating is
approximately 20 micrometres. Ensure that the welding fumes are not inhaled.
62
63

This chapter contains the instructions that you must follow when selecting the motor,
the cables, the protections, the cable routing and the way of operation for the drive
system.
Note: The installation must always be designed and made according to applicable
local laws and regulations. ABB does not assume any liability whatsoever for any
installation which breaches the local laws and/or other regulations. Furthermore, if
the recommendations given by ABB are not followed, the drive may experience
problems that the warranty does not cover.
Motor selection and compatibility

1. Select the motor according to the rating tables in chapter Technical data. Use
DriveSize PC tool if the default load cycles are not applicable.
2. Check that the motor ratings lie within the allowed ranges of the drive control
program:
• motor nominal voltage is 1/2 ... 2 · UN of the drive
• motor nominal current is 1/6 ... 2 · I2hd of the drive in DTC control and
0 ... 2 · I2hd in scalar control. The control mode is selected by a drive parameter.
3. Check that the motor voltage rating meets the application requirements:
If the drive is equipped with … … and … … then the motor voltage
rating should be …
diode supply no resistor braking is used UN

(ACS800-01, ACS800-U1,
frequent or long-term brake cycles UACeq1
ACS800-02, ACS800-U2,
ACS800-04, ACS800-04M, are used
ACS800-U4, ACS800-07,
ACS800-U7)
IGBT supply DC link voltage is not increased from UN

(ACS800-11, ACS800-U11, nominal (through parameter settings)
ACS800-31, ACS800-17,
DC link voltage is increased from UACeq2
ACS800-37)
nominal (through parameter settings)
UN = Rated input voltage of drive

UACeq1 = UDC / 1.35
UACeq2 = UDC / 1.41
UACeq = Equivalent AC power source voltage of drive in V AC
UDC = Maximum DC link voltage of drive in V DC. For resistor braking, UDC = 1.21 × nominal DC link
voltage. For units with IGBT supply: see the parameter value. Note: Nominal DC link voltage is UN × 1.35 or
UN × 1.41 in V DC.
See notes 6 and 7 below the Requirements table.

64
4. Consult the motor manufacturer before using a motor in a drive system where the
motor nominal voltage differs from the AC power source voltage.
5. Ensure that the motor insulation system withstands the maximum peak voltage in
the motor terminals. See the Requirements table below for the required motor
insulation system and drive filtering.
Example 1: When the supply voltage is 440 V and the drive has a diode supply
and operates in motor mode only, the maximum peak voltage at the motor
terminals can be approximated as follows: 440 V × 1.35 × 2 = 1190 V. Check that
the motor insulation system withstands this voltage.
Example 2: When the supply voltage is 440 V and the drive is equipped with an
IGBT supply, the maximum peak voltage in the motor terminals can be
approximated as follows: 440 V × 1.41 × 2 = 1241 V. Check that the motor
insulation system withstands this voltage.
Protecting the motor insulation and bearings

The output of the drive comprises – regardless of output frequency – pulses of
approximately 1.35 times the equivalent mains network voltage with a very short rise
time. This is the case with all drives employing modern IGBT inverter technology.
The voltage of the pulses can be almost double at the motor terminals, depending on
the attenuation and reflection properties of the motor cable and the terminals. This in
turn can cause additional stress on the motor and motor cable insulation.
Modern variable speed drives with their fast rising voltage pulses and high switching
frequencies can cause current pulses that flow through the motor bearings, which
can gradually erode the bearing races and rolling elements.
The stress on motor insulation can be avoided by using optional ABB du/dt filters.
du/dt filters also reduce bearing currents.
To avoid damage to motor bearings, the cables must be selected and installed
according to the instructions given in this manual. In addition, insulated N-end (non-
driven end) bearings and output filters from ABB must be used according to the
following table. Two types of filters are used individually or in combinations:
• du/dt filtering (protects motor insulation system and reduces bearing currents).
• common mode filtering (CMF) (mainly reduces bearing currents).
Requirements table
The following table shows how to select the motor insulation system and when an
optional ABB du/dt filter, insulated N-end (non-driven end) motor bearings and ABB
common mode filters are required. The motor manufacturer should be consulted
regarding the construction of the motor insulation and additional requirements for

65
explosion-safe (EX) motors. Failure of the motor to fulfil the following requirements
or improper installation may shorten motor life or damage the motor bearings.
Motor type Nominal mains Requirement for
voltage (AC line
Motor insulation ABB du/dt filter, insulated N-end bearing and ABB common mode
voltage) system filter
Manufacturer
PN < 100 kW 100 kW < PN < 350 kW PN > 350 kW

and or or
frame size < IEC 315 frame size > IEC 315 frame size > IEC 400
PN < 134 hp 134 hp < PN < 469 hp PN > 469 hp
and frame size or frame size or frame size
< NEMA 500 > NEMA 500 > NEMA 580
A Random- UN < 500 V Standard - +N + N + CMF
B wound M2_ 500 V < UN < 600 V Standard + du/dt + du/dt + N + du/dt + N + CMF
and M3_
B
or
Reinforced - +N + N + CMF
600 V < UN < 690 V Reinforced + du/dt + du/dt + N + du/dt + N + CMF
Form-wound 380 V < UN < 690 V Standard n.a. + N + CMF PN < 500 kW:
HX_ and AM_ + N + CMF
PN > 500 kW:
+ N + CMF + du/dt
Old* form- 380 V < UN < 690 V Check with the + du/dt with voltages over 500 V + N + CMF
wound HX_ motor
and modular manufacturer.
Random- 0 V < UN < 500 V Enamelled wire + N + CMF
wound HX_ with fibre glass
500 V < UN < 690 V + du/dt + N + CMF
and AM_ ** taping
N Random- UN < 420 V Standard: ÛLL = - + N or CMF + N + CMF
O wound and 1300 V
N form-wound 420 V < UN < 500 V Standard: ÛLL = + du/dt + du/dt + N + du/dt + N + CMF
- 1300 V
or
A
+ du/dt + CMF
B
or
B
Reinforced: ÛLL = - + N or CMF + N + CMF
1600 V, 0.2 µs
rise time
500 V < UN < 600 V Reinforced: ÛLL = + du/dt + du/dt + N + du/dt + N + CMF
1600 V
or
+ du/dt + CMF
or
Reinforced: ÛLL = - + N or CMF + N + CMF
1800 V
600 V < UN < 690 V Reinforced: ÛLL = + du/dt + du/dt + N + du/dt + N + CMF
1800 V
Reinforced: ÛLL = - N + CMF N + CMF
2000 V, 0.3 µs
rise time ***
* manufactured before 1.1.1998

** For motors manufactured before 1.1.1998, check for additional instructions with the motor manufacturer.
*** If the intermediate DC circuit voltage of the drive will be increased from the nominal level by resistor braking or
by the IGBT supply unit control program (parameter selectable function), check with the motor manufacturer if
additional output filters are needed in the applied drive operation range.

66
Note 1: The abbreviations used in the table are defined below.
Abbreviation Definition
UN nominal voltage of the supply network
ÛLL peak line-to-line voltage at motor terminals which the motor insulation must withstand
PN motor nominal power
du/dt du/dt filtering at the output of the drive (+E205)
CMF common mode filtering (+E208)
N N-end bearing: insulated motor non-driven end bearing
n.a. Motors of this power range are not available as standard units. Consult the motor manufacturer.
Note 2: Explosion-safe (EX) motors

The motor manufacturer should be consulted regarding the construction of the motor insulation and
additional requirements for explosion-safe (EX) motors.
Note 3: High-output motors and IP 23 motors
For motors with higher rated output than what is stated for the particular frame size in EN 50347 (2001)
and for IP 23 motors, the requirements of ABB random-wound motor series M3AA, M3AP, M3BP are
given below. For other motor types, see the Requirements table above. Apply the requirements of
range “100 kW < PN < 350 kW” to motors with PN < 100 kW. Apply the requirements of range PN >
350 kW to motors within the range “100 kW < PN < 350 kW”. In other cases, consult the motor
manufacturer.
Manufacturer
Motor type Nominal mains Requirement for

voltage (AC line
Motor insulation ABB du/dt filter, insulated N-end bearing and ABB common mode
voltage) system filter
PN < 55 kW 55 kW < PN < 200 kW PN > 200 kW
PN < 74 hp 74 hp < PN < 268 hp PN > 268 hp
A Random- UN < 500 V Standard - +N + N + CMF

B wound M3AA, 500 V < UN < 600 V Standard + du/dt + du/dt + N + du/dt + N + CMF
M3AP, M3BP
B
or
Reinforced - +N + N + CMF
600 V < UN < 690 V Reinforced + du/dt + du/dt + N + du/dt + N + CMF
Note 4: HXR and AMA motors

All AMA machines (manufactured in Helsinki) for drive systems have form-wound windings. All HXR
machines manufactured in Helsinki starting 1.1.1998 have form-wound windings.
Note 5: ABB motors of types other than M2_, M3_, HX_ and AM_
Use the selection criteria given for non-ABB motors.
Note 6: Resistor braking of the drive
When the drive is in braking mode for a large part of its operation time, the intermediate circuit DC
voltage of the drive increases, the effect being similar to increasing the supply voltage by up to 20
percent. The voltage increase should be taken into consideration when determining the motor insulation
requirement.
Example: Motor insulation requirement for a 400 V application must be selected as if the drive were
supplied with 480 V.
Note 7: Drives with an IGBT supply unit
If voltage is raised by the drive (this is a parameter selectable function for special applications only),
select the motor insulation system according to the increased intermediate circuit DC voltage level,
especially in the 500 V supply voltage range.

67
Note 8: Calculating the rise time and the peak line-to-line voltage
The peak line-to-line voltage at the motor terminals generated by the drive as well as the voltage rise
time depend on the cable length. The requirements for the motor insulation system given in the table
are “worst case” requirements covering installations with 30-metre and longer cables. The rise time can
be calculated as follows: t = 0.8 · ÛLL/(du/dt). Read ÛLL and du/dt from the diagrams below. Multiply
the values of the graph by the supply voltage (UN). In case of drives with an IGBT supply unit or resistor
braking, the ÛLL and du/dt values are approximately 20% higher.
3.0 3.0
ÛLL/U N ÛLL/U N
2.5 2.5
2.0 2.0
1.5 1.5
du/dt
------------- (1/μs)
UN
1.0 1.0
du/dt
------------- (1/μs)
UN
0.5 0.5
0.0 0.0
100 200 300 100 200 300
Cable length (m) Cable length (m)
With du/dt Filter (R6 and R7i) With du/dt Filter (R8i and nxR8i)
5.5
5.0
du/dt
------------- (1/μs)
4.5 UN
4.0
3.5
3.0
ÛLL/UN
2.5
2.0
1.5
1.0
100 200 300
Cable length (m)
Without du/dt Filter (all frame sizes)
Note 9: Sine filters

Sine filters protect the motor insulation system. Therefore, a du/dt filter can be replaced with a sine
filter. The peak phase-to-phase voltage with a sine filter is approximately 1.5 × UN.

68
Permanent magnet synchronous motor

Only one permanent magnet motor can be connected to the inverter output.
It is recommended to install a safety switch between a permanent magnet
synchronous motor and the motor cable. The switch is needed to isolate the motor
during any maintenance work on the drive.
Thermal overload and short-circuit protection

The drive protects itself and the input and motor cables against thermal overload
when the cables are dimensioned according to the nominal current of the drive. No
additional thermal protection devices are needed.
WARNING! If the drive is connected to multiple motors, a separate thermal overload

switch or a circuit breaker must be used for protecting each cable and motor. These
devices may require a separate fuse to cut off the short-circuit current.
The drive protects the motor cable and the motor in a short-circuit situation when the
motor cable is dimensioned according to the nominal current of the drive.
Supply (AC line) cable short-circuit protection

Always protect the input cable with fuses. In networks with a short-circuit withstand
of 65 kA or less, standard gG fuses can be used. No fuses need be installed at the
drive input.
If the drive is supplied through busbars, fuses must be installed at the drive input. In
networks with a short-circuit withstand of less than 50 kA, standard gG fuses are
sufficient. If the network has a short-circuit withstand of 50…65 kA, aR fuses are
required.
Size the fuses according to local safety regulations, appropriate input voltage and
the rated current of the drive. Check that the operating time of the fuses is below
0.5 seconds. For fuse ratings, see Technical Data.
WARNING! Circuit breakers are not capable of providing sufficient protection

because they are inherently slower than fuses. Always use fuses with circuit
breakers.

69
Earth fault (Ground fault) protection

Both the supply unit and the inverter unit are equipped with an internal earth fault
protective function to protect the drive against earth faults in the drive, motor and
motor cable. (This is not a personal safety or a fire protection feature.) Both earth
fault protective functions can be disabled by a parameter.
See the ACS800 Ordering Information (code: 64556568 [English], available on
request) for other available earth fault protection options.
The EMC filter (if present) includes capacitors connected between the main circuit
and the frame. These capacitors and long motor cables increase the earth leakage
current and may cause fault current circuit breakers to function.
Emergency stop devices

For safety reasons, install the emergency stop devices at each operator control
station and at other operating stations where emergency stop may be needed.
Pressing the stop key ( ) on the control panel of the drive, or turning the operating
switch of the drive from position “1” to “0” does not generate an emergency stop of
the motor or separate the drive from dangerous potential.
An emergency stop function is optionally available for stopping and switching off the
whole drive. Two modes are available: immediate removal of power (Category 0)
and controlled emergency stop (Category 1). These modes are implemented either
by activating the Safe torque off function, or by opening the main contactor or
breaker of the drive.
For more information, see Safety options for ACS800 cabinet-installed drives
(+Q950, +Q951, +Q952, +Q963, +Q964, +Q967 and +Q968): Wiring, start-up and
operation instructions (3AUA0000026238 [English]).

70
Prevention of unexpected start-up

The drive can be equipped with an optional Prevention of unexpected start-up
function according to standards IEC/EN 60204-1:1997; ISO/DIS 14118:2000,
EN 1037:1996, EN ISO 12100:2003, EN954-1:1996 and EN ISO 13849-2:2003.
Note: The Prevention of unexpected start-up function is not SIL/PL classified.
The function disables the control voltage of the power semiconductors of the drive
output stage, thus preventing the motor-side converter from generating the voltage
required to rotate the motor. By using this function, short-time operations (like
cleaning) and/or maintenance work on non-electrical parts of the machinery can be
performed without switching off the power supply to the drive.
The operator activates the Prevention of unexpected start-up function using a switch
mounted on a control desk. When the function is activated, the switch is opened, and
an indicator lamp will light.
WARNING! The Prevention of unexpected start-up function does not disconnect the
voltage of the main and auxiliary circuits from the drive. Therefore maintenance work
on electrical parts of the drive can only be carried out after isolating the drive system
from the main supply.
Note: If a running drive is stopped by using the Prevention of unexpected start-up

function, the drive will cut off the motor supply voltage and the motor will coast to
stop.

71
Safe torque off

The drive supports the Safe torque off function according to standards EN 61800-5-
2:2007; EN ISO 13849-1:2008, IEC 61508, IEC 61511:2004 and EN 62061:2005.
The function also corresponds to prevention of unexpected start-up of EN 1037.
The Safe torque off function disables the control voltage of the power
semiconductors of the drive output stage, thus preventing the inverter from
generating the voltage required to rotate the motor. By using this function, short-time
operations (like cleaning) and/or maintenance work on non-electrical parts of the
machinery can be performed without switching off the power supply to the drive.
WARNING! The Safe torque off function does not disconnect the voltage of the main
and auxiliary circuits from the drive. Therefore maintenance work on electrical parts
of the drive or the motor can only be carried out after isolating the drive system from
the main supply.
Note: It is not recommended to stop the drive by using the Safe torque off function. If
a running drive is stopped by using the Safe torque off function, the drive will stop by
coasting. If this causes danger or is not acceptable, the drive and machinery must be
stopped using the appropriate stopping mode before using the Safe torque off
function.
Note concerning permanent magnet motor drives in case of a multiple IGBT
power semiconductor failure: In spite of the activation of the Safe torque off
function, the drive system can produce an alignment torque which maximally rotates
the motor shaft by 180/p degrees. p denotes the pole pair number.
ATEX-certified thermal motor protection

The drive can be optionally equipped for ATEX-certified thermal motor protection.
The option includes the necessary safety relays and internal wiring. (The sensors or
sensor wiring are not included.)
The motor is located in a potentially explosive atmosphere. PTC or Pt100 sensors in
the bearings and/or stator winding of the motor are wired to the drive, which is
located outside the hazardous zone. When the motor temperature exceeds a certain
limit, the safety relay activates the Safe torque off function.
For more information, see ATEX-certified thermal motor protection functions for
ACS800 cabinet-installed drives (+L513+Q971 and +L514+Q971): Safety, wiring,
start-up and operation instructions (3AUA0000082378 [English]).

72
Selecting the power cables
General rules
Dimension the supply (input power) and motor cables according to local
regulations:
• The cable must be able to carry the drive load current. See chapter Technical
data for the rated currents.
• The cable must be rated for at least 70 °C maximum permissible temperature of
conductor in continuous use. For US, see Additional US requirements on
page 74.
• The inductance and impedance of the PE conductor/cable (grounding wire) must
be rated according to permissible touch voltage appearing under fault conditions
(so that the fault point voltage will not rise excessively when a ground fault
occurs).
• 600 V AC cable is accepted for up to 500 V AC. For 690 V AC rated equipment,
the rated voltage between the conductors of the cable should be minimum 1 kV.
We recommend shielded symmetrical multicore cables for input cabling. Single-core
cables are also allowed, but unshielded single-core cables are not on IT
(ungrounded) networks.
WARNING! Do not use unshielded single-core supply cables in IT (ungrounded)

networks. A dangerous voltage can become present on the non-conductive outer
sheath of the cable. This can cause injury or death.
Symmetrical shielded cable must be used for motor cabling; see section Alternative
power cable types on page 73.
Note: When continuous conduit is employed, shielded cable is not required.
To operate as a protective conductor, the shield conductivity must be as follows
when the protective conductor is made of the same metal as the phase conductors:
Cross-sectional area of the phase Minimum cross-sectional area of the
conductors corresponding protective conductor
S (mm2) Sp (mm 2)
S < 16 S
16 < S < 35 16
35 < S S/2
Compared to a four-conductor system, the use of symmetrical shielded cable

reduces electromagnetic emission of the whole drive system as well as motor
bearing currents and wear.
Note: The cabinet configuration of the drive may require multiple supply and/or
motor cabling. Refer to the connection diagrams in Electrical installation.
The motor cable and its PE pigtail (twisted screen) should be kept as short as
possible in order to reduce electromagnetic emission as well as capacitive current.

73
Alternative power cable types

Power cable types that can be used with the drive are represented below.
Recommended: Symmetrical shielded cable (three A separate PE conductor is required if the

phase conductors, concentric or otherwise conductivity of the cable shield is less than 50% of the
symmetrical PE conductor, overall shield) conductivity of a phase conductor.
PE conductor
and shield Shield Shield
PE
PE
Not allowed: Symmetrical cable with individual

shields for each phase conductor
Shield
(PE)
Not allowed for motor cabling: Separate cables for Not allowed for motor cabling with phase
each phase and PE conductor cross-section larger than 10 mm 2 (motor
power > 30 kW): Asymmetric cable
PE
Shield

74
Motor cable shield

To effectively suppress radiated and conducted radio-frequency emissions, the
shield conductivity must be at least 1/10 of the phase conductor conductivity. The
requirements are easily met with a copper or aluminium shield. The minimum
requirement of the motor cable shield of the drive is shown below. It consists of a
concentric layer of copper wires with an open helix of copper tape. The better and
tighter the shield, the lower the emission level and the bearing currents.
Copper wire screen Helix of copper tape Inner insulation

Insulation jacket
Cable core
Additional US requirements
Type MC continuous corrugated aluminum armor cable with symmetrical grounds or
shielded power cable must be used for the motor cables if metallic conduit is not
used. For the North American market, 600 V AC cable is accepted for up to
500 V AC. 1000 V AC cable is required above 500 V AC (below 600 V AC). For
drives rated over 100 amperes, the power cables must be rated for 75 °C (167 °F).
Conduit
Where conduits must be coupled together, bridge the joint with a ground conductor
bonded to the conduit on each side of the joint. Bond the conduits also to the drive
enclosure. Use separate conduits for input power, motor, brake resistors, and control
wiring. When conduit is employed, type MC continuous corrugated aluminum armor
cable or shielded cable is not required. A dedicated ground cable is always required.
Note: Do not run motor wiring from more than one drive in the same conduit.
Armored cable / shielded power cable
6-conductor (3 phases and 3 ground) type MC continuous corrugated aluminum
armor cable with symmetrical grounds is available from the following suppliers (trade
names in parentheses):
• Anixter Wire & Cable (Philsheath)
• BICC General Corp (Philsheath)
• Rockbestos Co. (Gardex)
• Oaknite (CLX).
Shielded power cables are available from Belden, Lapp Kabel (ÖLFLEX) and Pirelli,
among others.

75
Power factor compensation capacitors

Power factor compensation is not needed with AC drives. However, if a drive is to be
connected in a system with compensation capacitors installed, note the following
restrictions.
WARNING! Do not connect power factor compensation capacitors to the motor

cables (between the drive and the motor). They are not intended for use with AC
drives and can cause permanent damage to the drive or themselves.
If there are power factor compensation capacitors in parallel with the 3-phase input
of the drive:
1. Do not connect a high-power capacitor to the power line while the drive is
connected. The connection will cause voltage transients that may trip or even
damage the drive.
2. If capacitor load is increased/decreased step by step when the AC drive is
connected to the power line, ensure that the connection steps are low enough not
to cause voltage transients that would trip the drive.
3. Check that the power factor compensation unit is suitable for use in systems with
AC drives i.e. harmonic generating loads. In such systems, the compensation unit
should typically be equipped with a blocking reactor or harmonic filter.
Equipment connected to the motor cable
Installation of safety switches, contactors, connection boxes, etc.

To minimize the emission level when safety switches, contactors, connection boxes
or similar equipment are installed in the motor cable between the drive and the
motor:
• EU: Install the equipment in a metal enclosure with 360 degrees grounding for the
shields of both the incoming and outgoing cables, or in another way connect the
shields of the cables together.
• US: Install the equipment in a metal enclosure in a way that the conduit or motor
cable shielding runs consistently without breaks from the drive to the motor.
Bypass connection
WARNING! Never connect the supply power to the drive output terminals U2, V2
and W2. If frequent bypassing is required, employ mechanically connected switches
or contactors. Mains (line) voltage applied to the output can result in permanent
damage to the unit.

76
Before opening an output contactor (in DTC motor control mode)

Stop the drive and wait for the motor to stop before opening a contactor between the
output of the drive and the motor when the DTC control mode is selected. (See the
Firmware Manual of the drive for the required parameter settings.) Otherwise, the
contactor will be damaged.
In scalar control, the contactor can be opened with the drive running.
Relay output contacts and inductive loads

Inductive loads (such as relays, contactors, motors) cause voltage transients when
switched off.
The relay contacts of the RMIO board are protected with varistors (250 V) against
overvoltage peaks. In spite of this, it is highly recommended to equip inductive loads
with noise attenuating circuits (varistors, RC filters [AC] or diodes [DC]) in order to
minimize the EMC emission at switch-off. If not suppressed, the disturbances may
connect capacitively or inductively to other conductors in the control cable and form
a risk of malfunction in other parts of the system.
Install the protective component as close to the inductive load as possible. Do not
install the protective components at the terminal block.
Relay outputs
Varistor
RO (NC)
RO (C)
230 V AC
RO (NO)
RC filter
RO (NC)
230 V AC RO (C)
RO (NO)
Diode
RO (NC)
24 V DC RO (C)
RO (NO)

77
Selecting the control cables

All control cables must be shielded.
Use a double-shielded twisted pair cable (see figure a) for analogue signals. This
type of cable is recommended for the pulse encoder signals also. Employ one
individually shielded pair for each signal. Do not use common return for different
analogue signals.
A double-shielded cable is the best alternative for low-voltage digital signals but
single-shielded twisted multipair cable (figure b) is also usable.
a b
Double-shielded twisted Single-shielded twisted
pair cable multipair cable
Run analogue and digital signals in separate, shielded cables.

Relay-controlled signals, providing their voltage does not exceed 48 V, can be run in
the same cables as digital input signals. It is recommended that the relay-controlled
signals be run as twisted pairs.
Never mix 24 V DC and 115 / 230 V AC signals in the same cable.
Relay cable
The cable type with braided metallic screen (e.g. ÖLFLEX by Lapp Kabel) has been
tested and approved by ABB.
Control panel cable

In remote use, the cable connecting the control panel to the drive must not exceed 3
metres (10 ft). The cable type tested and approved by ABB is used in control panel
option kits.
Coaxial cable (for use with Advant Controllers AC 80/AC 800)

• 75 ohm
• RG59, diameter 7 mm or RG11, diameter 11 mm
• Maximum cable length: 300 m (1000 ft)

78
Connection of a motor temperature sensor to the drive I/O
WARNING! IEC 60664 requires double or reinforced insulation between live parts
and the surface of accessible parts of electrical equipment which are either non-
conductive or conductive but not connected to the protective earth.
To fulfil this requirement, the connection of a thermistor (and other similar
components) to the digital inputs of the drive can be implemented in three alternate
ways:
1. There is double or reinforced insulation between the thermistor and live parts of
the motor.
2. Circuits connected to all digital and analogue inputs of the drive are protected
against contact and insulated with basic insulation (the same voltage level as the
drive main circuit) from other low voltage circuits.
3. An external thermistor relay is used. The insulation of the relay must be rated for
the same voltage level as the main circuit of the drive. For connection, see the
Firmware Manual.
Installation sites above 2000 metres (6562 feet)
WARNING! Wear appropriate protection when installing, operating or servicing the

RMIO board wiring and optional modules attached to the board. The Protective Extra
Low Voltage (PELV) requirements stated in EN 61800-5-1 are not fulfilled at altitudes
above 2000 m (6562 ft).
Routing the cables

Route the motor cable away from other cable routes. Motor cables of several drives
can be run in parallel installed next to each other. It is recommended that the motor
cable, input power cable and control cables be installed on separate trays. Avoid
long parallel runs of motor cables with other cables in order to decrease
electromagnetic interference caused by the rapid changes in the drive output
voltage.
Where control cables must cross power cables make sure they are arranged at an
angle as near to 90 degrees as possible. Do not run extra cables through the drive.
The cable trays must have good electrical bonding to each other and to the
grounding electrodes. Aluminium tray systems can be used to improve local
equalizing of potential.

79
A diagram of the cable routing is below.
Motor cable
Drive
min 300 mm (12 in.)
Power cable
Input power cable Motor cable
min 200 mm (8 in.) 90 °

min 500 mm (20 in.)
Control cables
Control cable ducts

24 V 230/120 V 24 V 230/120 V
Not allowed unless the 24 V cable is Lead 24 V and 230/120 V control

insulated for 230 V (120 V) or cables in separate ducts into the
insulated with an insulation sleeving inside of the cabinet.
for 230 V (120 V).

80

81

This chapter describes the electrical installation procedure of the drive.
WARNING! Only qualified electricians are allowed to carry out the work described in
this chapter. Follow the Safety instructions on the first pages of this manual. Ignoring
the safety instructions can cause injury or death.
WARNING! During the installation procedure, inverter modules may have to be

temporarily extracted from the cabinet. The modules have a high centre of gravity. In
order to minimise the danger of toppling over, keep the support legs (if provided) of
the modules extended whenever manoeuvring the modules outside the cabinet.
Option coding
Some instructions contained within this chapter are intended for drives equipped
with certain options, marked with “plus codes” (e.g. +H359). The options included in
a drive are listed on its type code label. An option code listing is included in this
manual on page 42.
82
Before installation
Checking the insulation of the assembly

Drive
Do not make any voltage tolerance or insulation resistance tests (e.g. hi-pot or
megger) on any part of the drive as testing can damage the drive. Every drive has
been tested for insulation between the main circuit and the chassis at the factory.
Also, there are voltage-limiting circuits inside the drive which cut down the testing
voltage automatically.
Supply cable
Check the insulation of the supply (input) cable according to local regulations before
connecting to the drive.
Motor and motor cable
Check the insulation of the motor and motor cable as follows:
1. Check that the motor cable is connected to the motor, and disconnected from the
drive output terminals U2, V2 and W2.
2. Measure the insulation resistances of the motor cable and the motor between
each phase and the Protective Earth conductor using a measuring voltage of
500 V DC. The insulation resistance of an ABB motor must exceed 100 Mohm
(reference value at 25 °C or 77 °F). For the insulation resistance of other motors,
please consult the manufacturer’s instructions. Note: Moisture inside the motor
casing will reduce the insulation resistance. If moisture is suspected, dry the
motor and repeat the measurement.
U1
M
V1
3~
ohm W1
PE
IT (ungrounded) systems
EMC filter +E202
EMC filter +E202 is not suitable for use in an IT (ungrounded) system. If the drive is
equipped with EMC filter +E202, disconnect the ground connection of the filter
before connecting the drive to the supply network. For detailed instructions on how
to do this, please contact your local ABB representative. See also section
Compliance with EN 61800-3:2004 on page 154.
WARNING! If a drive with EMC filter +E202 is installed on an IT system [an

ungrounded power system or a high resistance-grounded (over 30 ohms) power
system], the system will be connected to ground potential through the EMC filter
capacitors of the drive. This may cause danger, or damage the unit.
83
EMC filter +E200

EMC filter +E200 is optional equipment in frame size R6, and not suitable for use in
an IT (ungrounded) system as such. If a drive of frame size R6 is equipped with
EMC filter +E200, disconnect the ground connection of the filter before connecting
the drive to the supply network. For detailed instructions on how to do this, please
contact your local ABB representative. See also section Compliance with EN 61800-
3:2004 on page 154.
WARNING! If a drive of frame size R6 equipped with EMC filter +E200 is installed on
an IT system [an ungrounded power system or a high resistance-grounded (over
30 ohms) power system], the system will be connected to ground potential through
the EMC filter capacitors of the drive. This may cause danger, or damage the unit.
EMC filter +E210

EMC filter +E210 is standard equipment in frame sizes R7i and R8i. The filter is
suitable for use both in TN (grounded) and IT (ungrounded) systems. See also
section Compliance with EN 61800-3:2004 on page 154.
84
Input power connection – Frame R6
Connection diagram
Q1 K1 U1
L1
L2
L3
PE
Connection procedure
Note: Before making the cable connections, check that the input of the auxiliary
voltage transformer (T10) is selected correctly according to the supply voltage.
1. Open the door of the cabinet.
2. Remove any shrouds that protect the input busbars and cable entries.
3. Lead the cables into the inside of the cubicle. It is recommended to apply 360°
grounding of the cable shields at the entry as shown below.
4. Connect the cables as follows:

• Twist the cable shields into bundles and connect to cabinet PE (ground) busbar.
Connect any separate ground conductors or cables to cabinet PE (ground)
busbar.
• Connect the phase conductors to the input power terminals (L1, L2, L3). For the
tightening torques, see chapter Technical data.
5. Provide support for the cables whenever necessary.
6. Refit all shrouds removed earlier and close the door.
85
Input power connection – Frame R7i
Connection diagram
Q1 K1 L1 U1
L1
L2
L3
PE
Note: Before making the cable connections, check that the input of the auxiliary
voltage transformer (T10) is selected correctly according to the supply voltage.
1. Open the door of the cabinet.

busbar.
86
Input power connection – Frame R8i
Connection diagram
Q1 K1 L1 U1
L1
L2
L3
PE
Note: Before making the cable connections, check that the tap settings of the
auxiliary voltage transformer (T10, located in the input/output cubicle) are correct in
regard to the supply voltage. See instructions on page 99.
1. Open the door of the input/output cubicle (see section Cabling direction starting on
page 33).

busbar.
87
Input power connection – Frame 2×R8i and up
Connection diagram
U<
Q1
L1
L2
L3
PE
Note: Before making the cable connections, check that the tap settings of the
auxiliary voltage transformer (T10, located in the auxiliary control cubicle) are correct
in regard to the supply voltage. See instructions on page 99.
1. Open the door of the incoming cubicle (see section Cabling direction starting on
page 33).

busbar.
88
Grounding of shielded single-core input cables

Connect the cable shield to the PE busbar at the transformer side only and insulate
the shield at the drive side.
Motor connection – Frame R6
Connection diagram
PE
U2
V2
U1
V1
M
W2
W1 3~
PE
1. Open the cabinet door.
2. Remove any shrouds that protect the output busbars and cable entries.

busbar.
• Connect the phase conductors to the output power terminals (U2, V2, W2). For
the tightening torques, see chapter Technical data.
89
Motor connection – Frame R7i
Connection diagram
PE
U2
V2
U1
V1
M
W2
W1 3~
PE
1. Open the cabinet door.

busbar.
90
Motor connection – Frame R8i units without option +E202 or +H359
Connection diagram
PE
U2
V2
U1
V1
M
W2
W1 3~
PE
Supply and inverter unit cubicle Input/output cubicle
1. Open the door of the input/output cubicle (see section Cabling direction starting on
page 33).

busbar.
91
Motor connection – Frame R8i with option +E202 but without +H359
Output busbars
The motor cables are to be connected to the output busbars behind the inverter
module. For the location and dimensions of the busbars, see chapter Dimensions.
Connection diagram
PE
U2
V2
U1
V1
M
W2
W1 3~
PE
Inverter unit cubicle
WARNING! Obey the safety instructions when you handle the heavy module! See
section Power module replacement (Frame R8i and up) on page 127. Ignoring these
instructions can cause physical injury or death, or damage to the equipment.
1. Extract the inverter module from the cubicle as described in section Extracting the
module from the cubicle on page 128.
2. Lead the cables into the cabinet at the inverter module. Make the 360° earthing
arrangement at the cable entry as shown below.
4. Cut the cables to suitable length.

5. Strip the cables and conductors.
busbar.
92

8. Insert the inverter module back into the cubicle as described in section Inserting
the module into the cubicle on page 131.
93
Motor connection – Units with common motor terminal cubicle (+H359)
Connection diagram
PE
U2
V2
U1
V1
M
W2
W1 3~
PE
Inverter unit cubicle(s) Common motor terminal

cubicle
1. Open the door of the common motor terminal cubicle (see section Cabling
direction starting on page 33).

busbar.
94
Motor connection – Frame 2×R8i and up without common motor terminal

cubicle
Output busbars
The motor cables are to be connected to the output busbars behind each inverter
module. For the location and dimensions of the busbars, see chapter Dimensions.
Connection diagram
PE
U2
V2
W2
U1
V1
M
W1 3~
U2 PE
V2
W2
Inverter unit cubicle(s)
WARNING! The cabling from all inverter modules to the motor must be physically
identical considering cable type, cross-sectional area, and length.
PE
U2
V2
W2
U1
V1
M
W1 3~
U2 PE
V2
W2
Inverter unit cubicle
95
WARNING! Obey the safety instructions when you handle the heavy module! See
section Power module replacement (Frame R8i and up) on page 127. Ignoring these
instructions can cause physical injury or death, or damage to the equipment.
1. Extract each inverter module from the cubicle as described in section Extracting
the module from the cubicle on page 128.
2. Lead the cables into the cabinet at the inverter module. Make the 360° earthing
arrangement at the cable entry as shown below.
4. Cut the cables to suitable length.

5. Strip the cables and conductors.
busbar.
8. Insert the inverter modules back into the cubicle as described in section Inserting
the module into the cubicle on page 131.
96
Control connections
Drive control connections

The control connections are made on the terminal blocks provided in the swing-out
frame of the drive. Refer to the circuit diagrams delivered with the drive, and to
chapter Motor control and I/O board (RMIO).
Supply unit control connections
The supply unit is controlled using the local control devices optionally mounted on
the cabinet door, i.e. the start switch, reset button and emergency stop button. No
additional control connections are used or needed. However, it is also possible to
• halt the supply unit by an external emergency stop button (if the unit is equipped
with a local emergency stop button, external buttons can be connected in series)
• read a fault indication through a relay output
• communicate with the unit through a serial communication interface.
Refer to the circuit diagrams delivered with the drive for the connection terminals for
the external control devices.
Open the cabinet door(s).
Remove the locking screws at the edge of the swing-out frame and open the frame.
Remove any shrouds that limit access to the cable lead-throughs and cable trunking.
Run the cables into the inside of the cabinet through the grommets provided.
Top entry units only: If several cables need to be run through one grommet, use Loctite 5221 (cat. no.
25551) under the grommet to seal the cable entry.
97
Units with EMI conductive cushions only:

Run the cables between the cushions as shown below. Strip the cable at this location to enable proper
connection of the bare shield and the cushions. Tighten the cushions firmly onto the cable shields.
Side view
Strain relief EMI conductive
cushions
Grommet Lead-through plate
If the outer surface of a cable shield is non-conductive, turn the shield inside out as shown below and
apply copper foil to keep the shielding continuous. Do not cut the grounding wire (if present).
Stripped cable Conductive surface of Stripped part covered

the shield exposed with copper foil
Copper foil
Cable shield Shielded twisted pair
Grounding wire
On top entry units, sort the cables so that the thinnest and thickest cables are at opposite ends of the
opening.
Top view
Thickest cable Thinnest cable
Run the cables to the appropriate terminals. Wherever possible, use the existing cable trunking in the
cabinet. Use sleeving wherever the cables are laid against sharp edges. When running cables to the
swing-out frame, leave some slack in the cable at the hinge to allow the frame to open fully. Tie the cables
to the cable supports wherever necessary.
Cut the cables to suitable length. Strip the cables and conductors.
Twist the cable shields into bundles and connect them to the ground terminal nearest to the terminal block.
Keep the unshielded portion of the cables as short as possible.
Connect the conductors to appropriate terminals (see chapter Motor control and I/O board (RMIO) and the
circuit diagrams delivered with the unit).
Refit any shrouds removed earlier. Close the swing-out frame, refasten, and close the cabinet door(s).
98
Installation of optional modules and PC

Optional modules (such as fieldbus adapters, I/O extension modules and pulse
encoder interfaces) are inserted into the optional module slot of the RMIO boards
(built in the RDCU drive control units) and secured with two screws. The slots on the
RMIO boards are described on page 38. See the appropriate optional module
manual for information on the cable connections.
Cabling of I/O and fieldbus modules
Module
Keep unshielded portion as
short as possible
Shield
1
2
3
4
To nearest PE terminal
Cabling of pulse encoder interface module
CHASSIS
RTAC-01
PULSE ENCODER INTERFACE
GND
Note 1: If the encoder is of unisolated
12345678 123456
SHLD
F01
type, ground the encoder cable at the
DE
23 6
SHLD
C
45
AB
789
CHA
drive end only. If the encoder is

CHA+
CHB
CHA-
X2
Keep unshielded portion as
WD/
galvanically isolated from the motor

CHB+
INIT
CHB-
NODE ID
short as possible CHZ+
CHZ-
shaft and the stator frame, ground the
0V
0V
encoder cable shield at the drive and
the encoder end.
1
2
3
4
VOUT
+15V
X1
VIN
+24V
Note 2: Twist the pair cable wires.
Fibre optic links

DDCS fibre optic links are provided by RDCO modules (optionally installed on the
RDCU control units) for PC tools, master/follower link, NDIO, NTAC, NAIO, AIMA I/O
module adapter and fieldbus adapter modules of type Nxxx. See the RDCO User’s
Manual [3AFE 64492209 (English)] for the connections. Observe colour coding
when installing fibre optic cables. Blue connectors go to blue terminals, and grey
connectors to grey terminals.
When installing multiple modules on the same channel, connect them in a ring.
99
Tap settings of the auxiliary voltage transformer (Frame R8i and up)
Primary
Secondary 3~ Input
Output
3~ input 1~ output 3~ output
Supply Tap settings Supply 230 V 115 V 400 V (50 Hz) 320 V (60 Hz)
Terminals
voltage A1 to... B1 to… C1 to… voltage Terminals Tap setting Terminals Tap setting Terminals Terminals
690 V A1, B1, C1 C2 A2 B2 690 V a3, n1 230– a4, n1 115– a1, b1, c1 a2, b2, c2
660 V A1, B1, C1 C2 A2 B2 660 V a3, n1 230+ a4, n1 115+ a1, b1, c1 a2, b2, c2
100
101

This chapter shows
• external control connections to the RMIO board for the ACS800 Standard Control
Program (Factory Macro)
• specifications of the inputs and outputs of the board.
To which products this chapter applies

This chapter applies to ACS800 units which employ the RMIO-01 board (revision J
or later) or the RMIO-02 board (revision H or later).
Note on cabinet-installed ACS800 drives

The terminals of the RMIO board are optionally wired to terminal block X2. The
connections shown below apply also to terminal block X2 (the markings are identical
to the ones on the RMIO board).
Terminals of X2 accept cables from 0.5 to 4.0 mm2 (22 to 12 AWG). The tightening
torque for screw terminals is 0.4 to 0.8 Nm (0.3 to 0.6 lbf.ft). For disconnecting wires
from spring terminals, use a screwdriver with a blade thickness of 0.6 mm (0.024”)
and width of 3.5 mm (0.138”), e.g. Phoenix Contact SZF 1-0,6X3,5.
Note on terminal labelling

Optional modules (type Rxxx) may have terminal designations that coincide with
those on the RMIO board.

102
External control connections (non-US)

External control cable connections to the RMIO board for the ACS800 Standard
Control Program (Factory Macro) are shown below. For external control connections
of other application macros and programs, see the appropriate Firmware Manual.
X20
Terminal block size: 1 VREF- Reference voltage -10 V DC, 1 kohm < RL
cables 0.3 to 3.3 mm2 (22 to 12 AWG) 2 AGND < 10 kohm
Tightening torque: X21
0.2 to 0.4 Nm (0.2 to 0.3 lbf ft) 1 VREF+ Reference voltage 10 V DC, 1 kohm < RL <
2 AGND 10 kohm
3 AI1+ Speed reference 0(2) ... 10 V, Rin >
4 AI1- 200 kohm
5 AI2+ By default, not in use. 0(4) ... 20 mA, Rin =
6 AI2- 100 ohm
8 AI3- 100 ohm
rpm 9 AO1+ Motor speed 0(4)...20 mA = 0...motor nom.
10 AO1- speed, RL < 700 ohm
A 11 AO2+ Output current 0(4)...20 mA = 0...motor
12 AO2- nom. current, RL < 700 ohm
X22
1 DI1 Stop/Start
1) Only effective if par. 10.03 is set to 2 DI2 Forward/Reverse 1)
REQUEST by the user. 3 DI3 Not in use
4 DI4 Acceleration & deceleration select 2)
2)
0 = open, 1 = closed 5 DI5 Constant speed select 3)
DI4 Ramp times according to 6 DI6 Constant speed select 3)
0 parameters 22.02 and 22.03 7 +24VD +24 V DC max. 100 mA
1 parameters 22.04 and 22.05 8 +24VD
9 DGND1 Digital ground
3) See par. group 12 CONSTANT
SPEEDS.
11 DIIL Start interlock (0 = stop) 4)
DI5 DI6 Operation
0 0 Set speed through AI1
X23
1 0 Constant speed 1 1 +24V Auxiliary voltage output/input, non-isolated,
0 1 Constant speed 2 2 GND 24 V DC 250 mA 5)
1 1 Constant speed 3 X25
1 RO1 Relay output 1: ready
4) See parameter 21.09 START INTRL 2 RO1
FUNC. 3 RO1
5) Total maximum output current
X26
shared between this output and
optional modules installed on the 1 RO2 Relay output 2: running
board. 2 RO2
3 RO2
X27
1 RO3 Relay output 3: fault (-1)
Fault 2 RO3
3 RO3

103
External control connections (US)

External control cable connections to the RMIO board for the ACS800 Standard
Control Program (Factory Macro US version) are shown below. For external control
connections of other application macros and programs, see the appropriate
Firmware Manual.
X20
Terminal block size: 1 VREF- Reference voltage -10 V DC, 1 kohm < RL
cables 0.3 to 3.3 mm2 (22 to 12 AWG) 2 AGND < 10 kohm
Tightening torque: X21
0.2 to 0.4 Nm (0.2 to 0.3 lbf ft) 1 VREF+ Reference voltage 10 V DC, 1 kohm < R L <
2 AGND 10 kohm
3 AI1+ Speed reference 0(2) ... 10 V, Rin >
4 AI1- 200 kohm
6 AI2- 100 ohm
8 AI3- 100 ohm
rpm 9 AO1+ Motor speed 0(4)...20 mA = 0...motor nom.
10 AO1- speed, R L < 700 ohm
A 11 AO2+ Output current 0(4)...20 mA = 0...motor
12 AO2- nom. current, RL < 700 ohm
X22
1 DI1 Start ( )
1) Only effective if par. 10.03 is set to 2 DI2 Stop ( )
REQUEST by the user. 3 DI3 Forward/Reverse 1)
4 DI4 Acceleration & deceleration select 2)
2)
0 = open, 1 = closed 5 DI5 Constant speed select 3)
DI4 Ramp times according to 6 DI6 Constant speed select 3)
0 parameters 22.02 and 22.03 7 +24VD +24 V DC max. 100 mA
1 parameters 22.04 and 22.05 8 +24VD
3) See par. group 12 CONSTANT
SPEEDS.
11 DIIL Start interlock (0 = stop) 4)
DI5 DI6 Operation
0 0 Set speed through AI1
X23
1 0 Constant speed 1 1 +24V Auxiliary voltage output/input, non-isolated,
0 1 Constant speed 2 2 GND 24 V DC 250 mA 5)
1 1 Constant speed 3 X25
1 RO1 Relay output 1: ready
4) See parameter 21.09 START INTRL 2 RO1
FUNC. 3 RO1
5) Total maximum output current
X26
shared between this output and
optional modules installed on the 1 RO2 Relay output 2: running
board. 2 RO2
3 RO2
X27
1 RO3 Relay output 3: fault (-1)
Fault 2 RO3
3 RO3

104
RMIO board specifications

Analogue inputs
With Standard Control Program two programmable differential current inputs (0 mA /
4 mA ... 20 mA, Rin = 100 ohm) and one programmable differential voltage input (-
10 V / 0 V / 2 V ... +10 V, Rin > 200 kohm).
The analogue inputs are galvanically isolated as a group.
Isolation test voltage 500 V AC, 1 min
Max. common mode voltage ±15 V DC
between the channels
Common mode rejection ratio > 60 dB at 50 Hz
Resolution 0.025 % (12 bit) for the -10 V ... +10 V input. 0.5 % (11 bit) for the 0 ... +10 V and 0 ...
20 mA inputs.
Inaccuracy ± 0.5 % (Full Scale Range) at 25 °C (77 °F). Temperature coefficient: ± 100 ppm/°C
(± 56 ppm/°F), max.
Constant voltage output

Voltage +10 V DC, 0, -10 V DC ± 0.5 % (Full Scale Range) at 25 °C (77 °F). Temperature
coefficient: ± 100 ppm/°C (± 56 ppm/°F) max.
Maximum load 10 mA
Applicable potentiometer 1 kohm to 10 kohm
Auxiliary power output

Voltage 24 V DC ± 10 %, short circuit proof
Maximum current 250 mA (shared between this output and optional modules installed on the RMIO)
Analogue outputs
Two programmable current outputs: 0 (4) to 20 mA, RL < 700 ohm
Resolution 0.1 % (10 bit)
Inaccuracy ± 1 % (Full Scale Range) at 25 °C (77 °F). Temperature coefficient: ± 200 ppm/°C
(± 111 ppm/°F) max.
Digital inputs
With Standard Control Program six programmable digital inputs (common ground: 24
V DC, -15 % to +20 %) and a start interlock input. Group isolated, can be divided in
two isolated groups (see Isolation and grounding diagram below).
Thermistor input: 5 mA, < 1.5 kohm “1” (normal temperature), > 4 kohm “0”
(high temperature), open circuit “0” (high temperature).
Internal supply for digital inputs (+24 V DC): short circuit proof. An external 24 V DC
supply can be used instead of the internal supply.
Isolation test voltage 500 V AC, 1 min
Logical thresholds < 8 V DC “0”, > 12 V DC “1”
Input current DI1 to DI 5: 10 mA, DI6: 5 mA
Filtering time constant 1 ms

105
Relay outputs
Three programmable relay outputs
Switching capacity 8 A at 24 V DC or 250 V AC, 0.4 A at 120 V DC
Minimum continuous current 5 mA rms at 24 V DC
Maximum continuous current 2 A rms
Isolation test voltage 4 kV AC, 1 minute
DDCS fibre optic link

With optional communication adapter module RDCO. Protocol: DDCS (ABB
Distributed Drives Communication System)
24 V DC power input
Voltage 24 V DC ± 10%
Typical current consumption 250 mA
(without optional modules)
Maximum current consumption 1200 mA (with optional modules inserted)
The terminals on the RMIO board as well as on the optional modules attachable to the board fulfil the Protective Extra
Low Voltage (PELV) requirements stated in EN 61800-5-1 provided that the external circuits connected to the terminals
also fulfil the requirements, and that the installation site is below 2000 m (6562 ft) in altitude. For installation at higher
altitudes, see page 78.

106
Isolation and grounding diagram
(Test voltage: 500 V AC)

X20
1 VREF-
2 AGND
X21
1 VREF+
2 AGND
3 AI1+
4 AI1- Common mode
voltage between
5 AI2+
channels ±15 V
6 AI2-
7 AI3+
8 AI3-
9 AO1+
10 AO1-
11 AO2+
12 AO2-
X22
1 DI1
2 DI2
3 DI3
4 DI4
Jumper J1 settings:
9 DGND1
5 DI5 All digital inputs share a common

J1
6 DI6 ground. This is the default setting.
7 +24VD
8 +24VD Grounds of input groups
11 DIIL DI1…DI4 and DI5/DI6/DIIL
or
are separate (isolation
10 DGND2 voltage 50 V).
X23
1 +24 V
2 GND
X25
1 RO1
2 RO1
3 RO1
X26
1 RO2
2 RO2
3 RO2
X27
1 RO3
2 RO3
3 RO3
(Test voltage:
4 kV AC)
Ground

107

This chapter contains an installation checklist, a start-up procedure for the drive, and
listings of parameters specific to the ACS800-17.
Installation checklist
Check the mechanical and electrical installation of the drive before start-up. Go
through the checklist below together with another person.
WARNING! Only qualified electricians are allowed to commission the drive. Read
and follow the Safety instructions on the first pages of this manual. Neglecting the
safety instructions can cause injury or death.
Check…
MECHANICAL INSTALLATION
The ambient operating conditions are allowed. See Electrical installation, Technical data: IEC ratings or Ambient
conditions.
The unit is fixed properly to floor. See Mechanical installation.
The cooling air will flow freely.
ELECTRICAL INSTALLATION See Planning the electrical installation, Electrical installation.
The motor and the driven equipment are ready for start.
The EMC filter (option +E202) is disconnected if the drive is connected to an IT (ungrounded) system.
The drive is grounded properly.
The supply (input power) voltage matches the nominal input voltage of the drive.
The supply (input power) connection to the input terminals are OK and the phase order is correct.
Appropriate supply (input power) fuses and disconnector are installed.
The motor connections at the output terminals are OK.
The motor cable is routed away from other cables.
Settings of the auxiliary voltage transformer.
There are no power factor compensation capacitors in the motor cable.
The external control connections inside the drive are OK.
There are no tools, foreign objects or dust from drilling inside the drive.
Supply (input power) voltage cannot be applied to the output of the drive (with a bypass connection).

108
Check…
For drives with the stop category 1 Emergency stop function (option +Q952 or +Q964): The delay time of the
safety relay and the deceleration time of the Emergency stop function have been set to a suitable value.
All shrouds are in place.
Start-up procedure
Action Additional information
WARNING! Ensure that the disconnector of the supply transformer is
locked to open position, i.e. no voltage is, or cannot be connected to
drive inadvertently. Check also by measuring that there is no voltage
connected.
Basic checks with no voltage connected
If the unit is equipped with an air circuit breaker, check the current trip Optional device. See the delivery-
limits of the breaker (preset at the factory). specific circuit diagrams.
General rule
Ensure the selectivity condition is fulfilled i.e. the breaker trips at a lower
current than the protection device of the supplying network, and that the
limit is high enough not to cause unnecessary trips during the
intermediate DC circuit load peak at start.
Long-term current limit
As a rule of thumb, this should be set to the rated AC current of the drive.
Peak current limit
As a rule of thumb, this should be set to a value 3-4 times the rated AC
current of the drive.
Check the settings of the relays and breakers/switches of the auxiliary Optional devices. See delivery
circuits. specific circuit diagrams.
Disconnect any unfinished or unchecked 230/115 V AC cables that lead
from the terminal blocks to the outside of the equipment.
For drive types ACS800-17-0640-3/0780-5/0790-7 and up: Locate the These drive types have two PPCS
APBU-xx PPCS branching units. Enable memory backup battery on branching units, one for the supply
each branching unit by setting actuator 6 of switch S3 to ON. unit, one for the inverter unit. By
default, memory backup is switched
off to save the battery.
Connecting voltage to input terminals and auxiliary circuit
WARNING! When voltage is connected to the input terminals, voltage
may also be connected to the auxiliary circuits of the drive.
Make sure that it is safe to apply voltage. Ensure that:
• nobody is working on the unit or circuits that are wired from outside into
the cabinets
• cabinet doors are closed
• covers of motor terminal boxes are in place.
Open the earthing/grounding switch (Q9) if present. The earthing/grounding switch and
the main disconnecting device are
either mechanically or electrically
interlocked so that the earthing/
grounding switch can only be closed
when the main disconnecting switch
is open, and vice versa.

109

Close the main breaker of the supply transformer.
Close the auxiliary circuit On/Off switch (Q100) if present.
Starting the supply unit
Close the main switch/disconnector (Q1).
Units with emergency stop: Turn the Start switch on the cabinet door
from 0 into START position for 2 seconds, then release the switch and
leave it in position 1.
Checks with the supply unit running
Check the settings of the earth fault (ground fault) monitoring device (if See chapter Electrical installation.
present).
Supply unit (line-side converter) program set-up
Parameters of the IGBT supply unit need not be set during the start-up See ACS800 IGBT Supply Control
procedure, or in normal use. In case the parameters of the supply unit Program Firmware Manual
need to be changed, switch the control panel (optional) to view the line- (3AFE68315735 [English]).
side converter as described in section Control panel on page 40.
Alternatively, a PC equipped with a programming tool (e.g.
DriveWindow) can be connected to channel CH3 of the inverter unit’s
RDCU.
Note: An automatic Line-Side Identification routine is active by default
and it is repeated each time the line-side converter receives a start
command after the control board (RMIO) is powered. The identification
should be performed at least once during the start-up. After this it can be
disabled with parameter 99.08 AUTO LINE ID RUN, especially if a quick
start is needed. If the phase order is changed after the first start, the
Line-side Identification routine needs to be repeated.
Note: It is recommended to set parameter 16.15 START MODE to
LEVEL if
• the motor is started and stopped frequently. This prolongs the life of
the charging contactor,
• the drive is equipped with the emergency stop option,
• when it is required to start the motor without delay after the start
command, or
• if the drive is connected to a common DC bus. Otherwise the
charging resistors may be damaged.
Note: The output voltage of the drive can be raised using a parameter
setting; for example, it is possible to run a 500 V motor off a 400 V
supply. Contact your local ABB representative for more information.
Inverter control program set-up
Follow the instructions in the Firmware Manual of the inverter unit to start See the Firmware Manual of the
up the drive and to set the drive parameters. inverter unit.

110

On-load checks
Start-up and validate these safety functions (if present): Optional functions. See:
• +Q950 (Prevention of unexpected start-up) - Safety options for ACS800 cabinet-
• +Q951 (Emergency stop, Category 0) installed drives (+Q950, +Q951,
+Q952, +Q963, +Q964, +Q967 and
• +Q952 (Emergency stop, Category 1)
+Q968): Wiring, start-up and
• +Q963 (Emergency stop, Category 0) operation instructions
• +Q964 (Emergency stop, Category 1) (3AUA0000026238 [English])
• +Q968 (Safe torque off with a safety relay). - delivery-specific circuit diagrams.
Check the functioning of the ATEX-certified thermal motor protection Optional function. See:
function (+Q971, if present). - ATEX-certified thermal motor
protection functions for ACS800
cabinet-installed drives
(+L513+Q971 and +L514+Q971):
Safety, wiring, start-up and operation
instructions (3AUA0000082378
[English]).
- delivery-specific circuit diagrams.
Check that the cooling fans rotate freely in the right direction, and the air Check visually that the fans rotate in
flows upwards. the direction indicated by an arrow
on the fan housing.
Check the direction of rotation of the motor.
ACS800-17-specific parameters in the IGBT Supply Control Program

The signals and parameters described in the tables below are included in the IGBT
Supply Control Program.

Term Definition
B Boolean
C Character string
Def. Default value
FbEq Fieldbus equivalent: the scaling between the value shown on the control
panel and the integer used in serial communication
I Integer
R Real
T. Data type (see B, C, I, R)

111
Parameters
No. Name/Value Description T./FbEq Def.
16 SYSTEM CTR Parameter lock, parameter back-up etc.
INPUTS
16.15 START MODE Selects start mode. B EDGE
LEVEL Starts converter by level of control command. Control command is 0
selected by parameter 98.01 COMMAND SEL and 98.02 COMM.
MODULE.
WARNING! After a fault reset, the converter will start if the
start signal is on.
EDGE Starts converter by EDGE of control command. Control command is 1

selected by parameter 98.01 COMMAND SEL and 98.02 COMM.
MODULE.
31 AUTOMATIC Automatic fault reset.
RESET Automatic resets are possible only for certain fault types and when the
automatic reset function is activated for that fault type.
The automatic reset function is not operational if the drive is in local
control (L visible on the first row of the control panel display).
WARNING! If the start command is selected and it is ON, the
line converter may restart immediately after automatic fault
reset. Ensure that the use of this feature will not cause
danger.
WARNING! Do not use these parameters when the drive is
connected to a common DC bus. The charging resistors may
be damaged in an automatic reset.
31.01 NUMBER OF TRIALS Defines the number of automatic fault resets the drive performs within I 0
the time defined by parameter 31.02.
Note: When the value of parameter is not 0 and parameter 98.02
COMM. MODULE is set to INU COM LIM, sending a fault bit of 08.01
MAIN STATUS WORD to inverter side is delayed 1 s to get time for
line-converter automatic reset function.
0…5 Number of the automatic resets 0

112
No. Name/Value Description T./FbEq Def.

31.02 TRIAL TIME Defines the time for the automatic fault reset function. See parameter R 30 s
31.01.
1.0 … 180.0 s Allowed resetting time 100 …
18000
31.03 DELAY TIME Defines the time that the drive will wait after a fault before attempting R 0s
an automatic reset. See parameter 31.01.
0.0 … 3.0 s Resetting delay 0 … 300
31.04 OVERCURRENT Activates/deactivates the automatic reset for the line converter B NO
overcurrent fault.
NO Inactive 0
YES Active 65535
31.05 OVERVOLTAGE Activates/deactivates the automatic reset for the intermediate link B NO
overvoltage fault.
NO Inactive 0
YES Active 65535
31.06 UNDERVOLTAGE Activates/deactivates the automatic reset for the intermediate link B NO
undervoltage fault.
NO Inactive 0
YES Active 65535
Default values of parameters with the ACS800-17

When the IGBT Supply Control Program is loaded into the ACS800-17, the following
parameters receive the default values given in the table below. Do not change the
default values. If they are changed, the drive will not operate properly.
Parameter Default value
11.01 DC REF SELECT FIELDBUS
11.02 Q REF SELECT PARAM 24.02
70.01 CH0 NODE ADDR 120
70.19 DDCS CH0 HW CONN RING
70.20 CH3 HW CONNECTION RING
71.01 CH0 DRIVEBUS MODE NO
98.01 COMMAND SEL MCW
98.02 COMM. MODULE INU COM LIM

113
ACS800-17-specific parameters in the inverter control program

The actual signals and parameters described in this section are included in the most
commonly used inverter control program, ACS800 Standard Control Program.
Term Definition
Actual signal Signal measured or calculated by the drive. Can be monitored by the
user. No user setting possible.
FbEq Fieldbus equivalent: The scaling between the value shown on the control
panel and the integer used in serial communication.
Parameter A user-adjustable operation instruction of the drive.

114
Actual signals and parameters of the supply unit control program visible also in
the inverter control program
No. Name/Value Description FbEq Def.
09 ACTUAL SIGNALS Signals from the supply unit (line-side converter).
09.12 LCU ACT SIGNAL 1 Line-side converter signal selected by par. 95.08 LCU PAR1 SEL. 1=1 106
09.13 LCU ACT SIGNAL 2 Line-side converter signal selected by par. 95.09 LCU PAR2 SEL. 1=1 110
95 HARDWARE SPECIF Line-side converter references and actual signal selections.
95.06 LCU Q PW REF Reactive power reference for the line-side converter i.e. the value 0
for par. 24.02 Q POWER REF2 in the IGBT Supply Control
Program.
Scaling example 1: 10000 equals to a value of 10000 of parameter
24.02 Q POWER REF2 and 100% of par. 24.01 Q POWER REF
(i.e. 100% of the converter nominal power given in par. 04.06
CONV NOM POWER) when par. 24.03 Q POWER REF2 SEL is
set to PERCENT.
Scaling example 2: Par. 24.03 Q POWER REF2 SEL is set to kVAr.
A value of 1000 of par. 95.06 equals to 1000 kVAr of par. 24.02 Q
POWER REF2. Value of par. 24.01 Q POWER REF is then 100 ·
(1000 kVAr divided by converter nominal power in kVAr)%.
Scaling example 3: Par. 24.03 Q POWER REF2 SEL is set to PHI.
A value of 10000 of par. 95.06 equals to a value of 100 deg of
parameter 24.02 Q POWER REF2 which is limited to 30 deg. The
value of par. 24.01 Q POWER REF will be determined
approximately according to the following equation where P is read
from actual signal 1.09 POWER:
S
P P Q
cos 30 = --- = -----------------------
S 2 2 30 deg
P +Q
P
Positive reference 30 deg denotes capacitive load.
Negative reference 30 deg denotes inductive load.
Par. 24.02 -30 -10 0 10 30 (deg)

Par. 95.01
-10000 -3000 -1000 0 1000 3000 +10000
-10000 ... +10000 Setting range. 1=1

95.07 LCU DC REF DC voltage reference for line converter i.e. the value for parameter 0
23.01 DC VOLT REF.
0 … 1100 Setting range in volts. 1=1V
95.08 LCU PAR1 SEL Selects the line converter address from which actual signal 9.12 106
LCU ACT SIGNAL 1 is read.
0 … 10000 Parameter index. 1=1
95.09 LCU PAR2 SEL Selects the line converter address from which actual signal 9.13 110
LCU ACT SIGNAL 2 is read.
0 … 10000 Parameter index. 1=1

115
Maintenance

This chapter contains preventive maintenance instructions.
Safety instructions
Only a qualified electrician is allowed to perform the maintenance.
Before starting work inside the cabinet,
• isolate the drive from the power supply (note that any switch-disconnector
installed in the drive does not switch off the voltage from the input terminals)
• wait for 5 minutes to let the intermediate circuit capacitors discharge
• open the cabinet doors
• ensure there is no dangerous voltage present by measuring the voltage of the
input terminals and the intermediate circuit terminals.
Maintenance intervals
If installed in an appropriate environment, the drive requires very little maintenance.
This table lists the routine maintenance intervals recommended by ABB.
Interval Maintenance action Instruction
See Converter module capacitor reforming

Every year of storage Capacitor reforming instructions (Code: 3BFE 64059629 [English]) and
Capacitors.
Every 6 to 12 months (depending Heatsink temperature

See Heatsinks.
on dustiness of environment) check and cleaning
Air filter check;

Every year (IP22 and IP42 units)
replacement if necessary See Checking and replacing the air filters.
Every year (IP54 units) Air filter replacement
Every 3 years (Frame R8i and Quick connector check

See Quick connectors (Frame R8i and up).
larger units) and cleaning
Cabinet cooling fan

See Cooling fans.
replacement
Power module cooling fan

Every 6 years See Cooling fans.
replacement
LCL filter cooling fan

See Cooling fans.
replacement
Every 9 years Capacitor replacement See Capacitors.
Maintenance
116
Consult your local ABB Service representative for more details on the maintenance.
On the Internet, go to http://www.abb.com/drivesservices.
Reduced run capability

If one of the parallel-connected (frame R8i) inverter modules of an inverter unit must
be taken out of the cabinet for service, it is possible to continue operation at reduced
power using the remaining modules. Contact an ABB representative for directions.
Checking and replacing the air filters

1. Read and repeat the steps in section Safety instructions on page 115.
2. Open the cabinet doors.
3. Check the air filters and replace if necessary (see chapter Technical data for the
correct filter types). The inlet (door) filters can be accessed by removing the
fastener(s) at the top of the grille, then lifting the grille and pulling it away from the
door. The outlet (roof) filter in IP54 units has a similar mechanism.
4. Check the cleanliness of the cabinet. Clean the interior of the cabinet if necessary
using a soft brush and a vacuum cleaner.
5. Close the cabinet doors.
Maintenance
117
Quick connectors (Frame R8i and up)

2. Open the cabinet doors.
3. Extract a supply module or inverter module from the cabinet. See section Power
module replacement (Frame R8i and up) on page 127. Obey the safety
instructions when you handle the heavy module!
4. Check the tightness of the cable connections at the quick connector. Use the
tightening torque table in chapter Technical data.
5. Clean all contact surfaces of the quick connector and apply a layer of suitable joint
compound (e.g. Isoflex® Topas NB 52 from Klüber Lubrication) onto them.
6. Re-insert the supply/inverter module.
7. Repeat steps 3 to 6 for all remaining supply and inverter modules.
8. On frame R8i units (with ALCL-1x-x LCL filter), repeat steps 3 to 6 for the LCL
filter module.
Maintenance
118
Cooling fans
Supply/Inverter module cooling fan replacement (Frame R6)

2. Loosen the fastening screws of the fan housing.
3. Push the fan housing backwards.
4. Lift the fan housing up (out of the way).
5. Disconnect the fan supply wires (detachable connector).
6. Remove the fan.
7. Install the new fan in reverse order.
4
3
2 6
2
5
Maintenance
119
Supply/Inverter module cooling fan replacement (Frame R7i)

1. Disconnect the wire plug.
2. Remove the two screws holding the fan unit.
3. Pull the fan unit slightly towards the front of the cubicle, then downwards to free it.
Maintenance
120
LCL filter module cooling fan replacement (Frame R7i)

1. Disconnect the wire plug (1).
2. Remove the two screws holding the fan unit (2).
3. Pull the fan unit out (3).
2 2
Maintenance
121
Supply and inverter module cooling fan replacement (Frame R8i and up)
The actual lifespan of the fan depends on the running time of the fan, ambient
temperature and dust concentration. Each supply and inverter module has its own
cooling fan. Replacements are available from ABB. Do not use other than ABB
specified spare parts.
The supply and inverter control programs keep track of the running times of the
cooling fans of the supply and inverter modules respectively. See the Firmware
Manuals delivered with the drive for the actual signals which indicate the running
time.
Module fan replacement procedure
2. Disconnect the fan wiring plug (1).
3. Remove the locking screws (2).
4. Pull the fan out along its sliding rails (3).
5. Install a new fan in reverse order.
Maintenance
122
LCL filter cooling fan replacement (Frame R8i and up)

The actual lifespan of the fan depends on the running time of the fan, ambient
temperature and dust concentration. Replacements are available from ABB. Do not
use other than ABB specified spare parts.
LCL filter fan replacement procedure
2. Disconnect the fan wiring plug (1).
3. Remove the screws of the fan fastening rail/clip (2).
4. Pull the fan out (3).
5. Install a new fan in reverse order.
ALCL-1x ALCL-2x
2 2
1
3
Maintenance
123
Cabinet fan replacement (Frame R6)

2. Open the cubicle door.
3. Remove the shroud covering the top of the cubicle.
4. Disconnect the fan wiring. Make note of the connections at the terminal block.
5. Undo the two fastening screws that secure the fan holder to the cubicle
roofplate.
6. Pull out the fan holder plate together with the fan.
7. Remove the four screws that fasten the fan to the holder.
8. Install new fan in reverse order.
Cabinet fan replacement (Frame R8i with IP21-42)
Fan holder
1. Remove the eight screws attaching the fan holder to the cabinet roof.
2. Lift the fan holder until the fan cable can be disconnected.
3. Disconnect the fan cable.
4. Remove the fan from the fan holder.
5. Fasten a new fan to the fan holder.
6. Reconnect the fan cable.
7. Insert the fan holder into the aperture in the cabinet roof. Make sure the gasket
is not displaced while doing this.
8. Fasten the eight screws attaching the fan holder.
Maintenance
124
Cabinet fan replacement (Frame 2xR8i and up with IP21-42)
WARNING! Read and follow the instructions in chapter Safety instructions. Ignoring
the instructions can cause physical injury or death, or damage to the equipment.
1. Switch off the power to the unit and open the main disconnecting device. Close
the grounding switch (option +F259) if there is one.
2. Let the intermediate circuit DC capacitors discharge for five minutes. Ensure by
measuring that the drive is not live before starting the work.
3. Remove the grating (A) and the two fans by undoing the four screws (B).
4. If necessary, undo the four screws (C) to remove the airflow guide (D).
B
B C
D
C
Maintenance
125
Cabinet fan replacement (Frame R8i and up with IP54)

1. Remove the front and back gratings of the fan cubicle by lifting them upwards.
2. Remove the shrouds by undoing the fastening screws.
3. Undo the fastening screws of the side/top cover of the fan.
4. Lift the side/top cover of the fan off.
5. Disconnect the fan supply wire connector from the cabinet roof (on top and
inside the cabinet).
6. Undo the fastening screws of the fan cassette at each corner.
7. Lift the fan cassette off.
8. Undo the cable ties on the top of the fan cassette.
9. Disconnect the fan.
10. Remove the fan capacitor by undoing the fastening screw of the clamp.
11. Undo the fastening screws of the fan.
12. Pull the fan out.
13. Install the new fan and fan capacitor in reverse order to the above. Ensure that
the fan is centred and rotates freely.
2 2 4
1
3
2
2
3
7
6
5
5
Maintenance
126
10
9
8
8
9
8 8
12
11 11
Heatsinks
The heatsink fins of the power modules pick up dust from the cooling air. The module
runs into overtemperature warnings and faults if the heatsinks are not clean. In a
“normal” environment (not especially dusty nor clean) the heatsinks should be
checked annually, in a dusty environment more often.
Whenever necessary, clean the heatsinks as follows:
1. Remove the cooling fan (see section Cooling fans on page 118).
2. Blow dry clean compressed air from bottom to top and simultaneously use a
vacuum cleaner at the air outlet to trap the dust. Note: Prevent the dust from
entering adjoining equipment.
3. Refit the cooling fan.
Capacitors
The inverter modules employ several electrolytic capacitors. Their actual lifespan
depends on the operating time of the drive, loading and ambient temperature.
Capacitor life can be prolonged by lowering the ambient temperature.
It is not possible to predict capacitor failure. Capacitor failure is usually followed by
damage to the unit and an input cable fuse failure, or a fault trip. Contact ABB if
capacitor failure is suspected.
Reforming
Reform (re-age) spare part capacitors once a year according to Converter module
capacitor reforming instructions (code: 64059629 [English], available through your
local ABB representative.
Capacitor replacement
Contact an ABB service representative.
Maintenance
127
Power module replacement (Frame R8i and up)
WARNING! Ignoring the following instructions can cause physical injury or death,
or damage to the equipment.
• Use extreme caution when manoeuvring an inverter, supply or filter module

that runs on wheels. The modules are heavy and have a high centre of gravity.
They topple over easily if handled carelessly.
• Do not use the ramp which is supplied with the drive with heights over 50 mm
(the standard plinth height of ABB cabinets). The ramp is designed for a plinth
height of 50 mm.
Support the top and Do not tilt! Extend the support legs outside the
bottom of the module cabinet!
while removing!
max 50 mm
Lift the module by the upper part Mind your fingers! Keep fingers away from the Support the top and
only using the lifting hole(s) at the edges of the front flange of the module! bottom of the module while
top! replacing!
Maintenance
128
Extracting the module from the cubicle

2. Open the door of the supply and inverter unit cubicle (see section Cabling
direction starting on page 33).
3. Remove any shrouds that protect the busbars and cable entries.
4. Open the transparent cover on the front of the module and disconnect the fibre
optic cables. Move the cables aside.
5. Remove the L-shaped DC busbars on top of the module – be careful not to drop
the screws or busbars inside the module.
6. Disconnect the terminal block (X50) next to the DC busbars.
7. At the base of the module, loosen the two fastening screws (7a) but leave them
in place; lift the bracket (7b) into the up position. (Loosen the locking screws on
the sides of the bracket a bit, too, if necessary.)
8. Insert the module pull-out ramp under the two screws at the base of the module
and tighten.
WARNING! Do not use the ramp which is supplied with the drive with heights over
50 mm (the standard plinth height of ABB cabinets). The ramp is designed for a
plinth height of 50 mm.
9. Remove the two module fastening screws at the top.

10. Pull the module carefully out of the cubicle along the ramp.
WARNING! Make sure that the wires do not catch. While pulling on the handle, keep
a constant pressure with one foot on the base of the module to prevent the module
from falling on its back. Use safety shoes with metal toe cap to avoid foot injury.
11. Extend the support legs of the module. Keep the legs extended until the module
is about to be inserted back into the cubicle.
Maintenance
129
5 6
7b
8
7a
Maintenance
130
10 11 View from back:
Maintenance
131
Inserting the module into the cubicle

1. Move the module close to the ramp, and then retract the support legs of the
module.
2. Push the module up the ramp and back into the cubicle.
WARNING! Keep your fingers away from the edge of the module front plate to avoid
pinching them between the module and the cubicle. Also, keep a constant pressure
with one foot on the base of the module to prevent the module from falling on its
back.
3. Fasten the module fixing screws at the top and reconnect the DC busbars.
4. Connect the cables (X50, fibre optic cables).
5. Loosen the fastening screws at the base of the module and remove the pull-out
ramp. Flip the module fastening bracket into the down position and tighten the
screws.
6. Fasten the shroud and close the cubicle door.
Maintenance
132
Maintenance
133
Fault tracing
Faults and warnings displayed by the CDP-312R Control Panel

The control panel will display the warnings and faults of the unit (i.e. supply unit or
inverter unit) the panel is currently controlling.
Information on warnings and faults concerning the supply unit (line-side converter)
are contained within the IGBT Supply Control Program Firmware Manual
(3AFE68315735 [English]).
The warnings and faults concerning the inverter unit (motor-side converter) are dealt
with in the inverter control program (e.g. Standard Control Program) Firmware
Manual.
Warning/Fault message from unit not being monitored by control panel

Flashing messages WARNING, ID:2 or FAULT, ID:2 on the control panel display
indicate a warning or fault state in the line-side converter when the panel is
controlling the motor-side converter:
FAULT, ID:2
ACS 800 0490_3MR
*** FAULT ***
LINE CONV (FF51)
To display the warning or fault identification text, switch the control panel to view the
line-side converter as described in section Control panel on page 40.
Conflicting ID numbers
If the ID numbers of the line-side and the motor-side converters are set equal, the
control panel stops functioning. To clear the situation:
• Disconnect the panel cable from the RMIO board of the motor-side converter.
• Set the ID number of the line-side converter RMIO board to 2. For the setting
procedure, see the inverter control program (e.g. Standard Control Program)
Firmware Manual.
• Connect the disconnected cable to the RMIO board of the motor-side converter
again and set the ID number to 1.
Fault tracing
134
LEDs of the drive
Location LED Indication
RMIO board (RDCU drive control Red Fault state.

unit)
Green The power supply on the board is OK.
Control panel mounting platform Red Fault state.
(with the control panel removed)
Green The main + 24 V power supply for the control panel and the
RMIO board is OK.
AINT board (visible through the V204 (green) +5 V voltage of the board is OK.
transparent cover on the front of the
V309 (red) Prevention of unexpected start-up (option +Q950) or Safe
supply and inverter modules)
torque off (option +Q968) is ON.
V310 (green) IGBT control signal transmission to the gate driver control
boards is enabled.
Fault tracing
135
Technical data

This chapter contains the technical specifications of the drive, e.g. ratings, frame
sizes and technical requirements, provisions for fulfilling the requirements for CE
and other markings, and warranty information.
IEC ratings
The ratings for the ACS800-17 with a 50 Hz supply are given below. The symbols
are described below the table.
No-over- Light- Heavy-duty Heat dissi- Air Noise
Nominal ratings
load use overload use use pation flow level
ACS800-17 type
I1N Icont.max Imax Pcont.max I2N PN I2hd Phd
A A A kW A kW A kW kW m3/h dBA
Three-phase supply voltage 380 V, 400 V or 415 V
ACS800-17-0060-3 112 120 168 55 114 55 88 45 1.8 500 73
ACS800-17-0070-3 140 150 234 75 142 75 117 55 2.4 500 73
ACS800-17-0100-3 153 165 264 90 157 75 132 75 2.8 500 73
ACS800-17-0140-3 182 202 293 110 194 90 151 75 6 1300 74
ACS800-17-0170-3 224 250 363 132 240 132 187 90 7 1300 74
ACS800-17-0210-3 263 292 400 160 280 160 218 110 7 3160 75
ACS800-17-0260-3 333 370 506 200 355 200 277 132 9 3160 75
ACS800-17-0320-3 423 469 642 250 450 250 351 200 11 3160 75
ACS800-17-0390-3 509 565 773 315 542 315 423 250 14 3160 75
ACS800-17-0490-3 630 704 963 400 675 355 526 250 19 3160 75
ACS800-17-0640-3 828 919 1258 500 882 500 688 355 22 6400 77
ACS800-17-0770-3 1001 1111 1521 630 1067 630 831 450 28 6400 77
ACS800-17-0960-3 1235 1379 1888 800 1324 710 1031 560 36 6400 77
ACS800-17-1070-3 1383 1535 2102 900 1474 800 1149 630 39 10240 78
ACS800-17-1370-3 1833 1978 2707 1200 1899 1100 1479 800 51 10240 78
ACS800-17-1810-3 2419 2610 3573 1600 2506 1400 1953 1100 67 12800 78
Three-phase supply voltage 380 V, 400 V, 415 V, 440 V, 460 V, 480 V or 500 V
ACS800-17-0070-5 112 120 168 75 114 75 88 55 2.4 500 73
ACS800-17-0100-5 129 139 234 90 132 90 114 75 2.8 500 73
ACS800-17-0120-5 145 156 264 110 148 (1 90 125 75 3.4 500 73
ACS800-17-0170-5 180 200 291 132 192 132 150 90 6 1300 74
ACS800-17-0210-5 220 245 356 160 235 (2 160 183 110 8 1300 74
ACS800-17-0260-5 270 302 438 200 289 (3 200 226 132 8 3160 75
ACS800-17-0320-5 329 365 530 250 350 (4 250 273 160 10 3160 75
ACS800-17-0400-5 410 455 660 315 437 315 340 200 12 3160 75
ACS800-17-0460-5 473 525 762 355 504 355 393 250 14 3160 75
ACS800-17-0510-5 536 595 863 400 571 400 445 315 16 3160 75
ACS800-17-0580-5 600 670 972 500 643 450 501 315 19 3160 75
ACS800-17-0780-5 803 892 1294 630 856 630 667 450 24 6400 77
ACS800-17-0870-5 900 1005 1458 710 965 630 752 500 28 6400 77
ACS800-17-1140-5 1176 1313 1906 900 1261 900 982 710 36 6400 77
ACS800-17-1330-5 1376 1528 2217 1120 1467 1120 1143 800 41 10240 78
Technical data
136
No-over- Light- Heavy-duty Heat dissi- Air Noise

Nominal ratings
load use overload use use pation flow level
ACS800-17 type
I1N Icont.max Imax Pcont.max I2N PN I2hd Phd
A A A kW A kW A kW kW m3/h dBA
ACS800-17-1640-5 1746 1884 2734 1400 1809 1300 1409 1000 52 10240 78
ACS800-17-2160-5 2304 2486 3608 1800 2387 1700 1860 1300 68 12800 79
Three-phase supply voltage 525 V, 550 V, 575 V, 600 V, 660 V, or 690 V
ACS800-17-0060-7 53 57 86 55 54 45 43 37 1.8 500 73
ACS800-17-0070-7 73 79 120 75 75 55 60 55 2.4 500 73
ACS800-17-0100-7 86 93 142 90 88 75 71 55 2.8 500 73
ACS800-17-0160-7 119 132 192 110 127 110 99 90 7 1300 74
ACS800-17-0200-7 135 150 218 132 144 132 112 90 8 1300 74
ACS800-17-0260-7 180 201 301 200 193 160 150 132 11 3160 75
ACS800-17-0320-7 250 279 417 250 268 250 209 200 12 3160 75
ACS800-17-0400-7 300 335 502 315 322 250 251 200 16 3160 75
ACS800-17-0440-7 344 382 571 355 367 355 286 270 17 3160 75
ACS800-17-0540-7 400 447 668 450 429 400 334 315 18 3160 75
ACS800-17-0790-7 593 659 985 630 632 630 493 450 33 6400 77
ACS800-17-0870-7 657 729 1091 710 700 710 545 500 32 6400 77
ACS800-17-1050-7 784 876 1310 900 840 800 655 630 36 6400 77
ACS800-17-1330-7 1001 1112 1663 1120 1067 1120 831 800 48 10240 78
ACS800-17-1510-7 1164 1256 1879 1250 1206 1200 940 900 51 10240 78
ACS800-17-1980-7 1536 1657 2480 1700 1591 1600 1240 1200 67 12800 79
ACS800-17-2780-7 2091 2321 3472 2300 2228 2300 1736 1600 94 17920 79
ACS800-17-2940-7 2280 2460 3680 2500 2362 2400 1840 1800 99 19200 79
(1) 156 A allowed at 460 V
PDM-184674-E51
Symbols
Nominal ratings
I1N Nominal input current
Icont.max Continuous RMS output current. No overloadability at 40 °C (104 °F).
Imax Maximum output current. Allowable for 10 seconds at start, otherwise as long as allowed
by drive temperature.
Typical ratings for no-overload use
Pcont.max Typical motor power. The power ratings apply to most IEC 34 motors at nominal voltage
(400, 500 or 690 V).
Typical ratings for light-overload use (10% overloadability)
I2N Continuous rms current. 10% overload is allowed for 1 minute every 5 minutes.
PN Typical motor power. The power ratings apply to most IEC 34 motors at nominal voltage
(400, 500 or 690 V).
Typical ratings for heavy-duty use (50% overloadability)
I2hd Continuous rms current. 50% overload is allowed for 1 minute every 5 minutes.
Phd Typical motor power. The power ratings apply to most IEC 34 motors at nominal voltage
(400, 500 or 690 V).
Derating
The load capacity (current and power) decreases if the installation site altitude exceeds 1000 metres
(3281 ft), or if the ambient temperature exceeds 40 °C (104 °F).
Technical data
137
Temperature derating
In the temperature range +40 °C (+104 °F) to +50 °C (+122 °F), the rated output current is decreased
by 1% for every additional 1 °C (1.8 °F). The output current is calculated by multiplying the current
given in the rating table by the derating factor.
Example If the ambient temperature is 50 °C (+122 °F), the derating factor is 100 % - 1 % · 10 °C =
90% or 0.90. The output current is then 0.90 × I or 0.90 × I . °C
2N cont.max
Altitude derating
At altitudes from 1000 to 4000 m (3281 to 13123 ft) above sea level, the derating is 1% for every 100 m
(328 ft). For a more accurate derating, use the DriveSize PC tool. If the installation site is higher than
2000 m (6600 ft) above sea level, please contact your local ABB distributor or office for further
information.
Technical data
138
NEMA ratings
The ratings for the ACS800-17 with a 60 Hz supply are given below. The symbols
are described below the table.
Heavy-duty Heat dis- Noise
Nominal ratings Normal use Air flow
use sipation level
ACS800-17 type
I1N Imax Pcont.max I2N PN I2hd Phd
A A hp A hp A hp kW ft3/min dBA
Three-phase supply voltage 380 V, 400 V, 415 V, 440 V, 460 V or 480 V
ACS800-17-0070-5 112 168 75 114 75 88 60 2.4 295 73
ACS800-17-0100-5 129 234 100 132 100 114 75 2.8 295 73
ACS800-17-0120-5 145 264 125 148 (1 125 125 100 3.4 295 73
ACS800-17-0170-5 180 291 150 192 150 156 100 6 765 74
ACS800-17-0210-5 220 356 200 235 (2 200 183 150 8 765 74
ACS800-17-0260-5 270 438 250 289 (3 250 226 150 8 1860 75
ACS800-17-0320-5 329 530 300 350 (4 300 273 200 10 1860 75
ACS800-17-0400-5 410 660 350 437 350 340 250 12 1860 75
ACS800-17-0460-5 473 762 450 504 400 393 300 14 1860 75
ACS800-17-0510-5 536 863 500 571 450 445 350 16 1860 75
ACS800-17-0580-5 600 972 550 643 500 501 400 19 1860 75
ACS800-17-0780-5 803 1294 750 856 700 667 550 24 3770 77
ACS800-17-0870-5 900 1458 900 965 800 752 650 28 3770 77
ACS800-17-1140-5 1176 1906 1150 1261 1050 982 850 36 3770 77
ACS800-17-1330-5 1376 2217 1300 1467 1250 1143 1000 41 6030 78
ACS800-17-1640-5 1746 2734 1650 1809 1550 1409 1250 52 6030 78
ACS800-17-2160-5 2304 3608 2150 2387 2050 1860 1600 68 7530 79
ACS800-17-0060-7 53 86 60 54 50 43 40 1.8 295 73
ACS800-17-0070-7 73 120 75 75 60 60 50 2.4 295 73
ACS800-17-0100-7 86 142 100 88 75 71 60 2.8 295 73
ACS800-17-0160-7 119 192 125 127 125 99 100 7 765 74
ACS800-17-0200-7 135 218 150 144 150 112 100 8 765 74
ACS800-17-0260-7 180 301 200 193 200 150 150 11 1860 75
ACS800-17-0320-7 250 417 250 268 250 209 200 12 1860 75
ACS800-17-0400-7 300 502 350 322 300 251 250 16 1860 75
ACS800-17-0440-7 344 571 400 367 350 286 300 17 1860 75
ACS800-17-0540-7 400 668 450 429 450 334 350 18 1860 75
ACS800-17-0790-7 593 985 700 632 650 493 500 33 3770 77
ACS800-17-0870-7 657 1091 800 700 750 545 600 32 3770 77
ACS800-17-1050-7 784 1310 950 840 900 655 700 36 3770 77
ACS800-17-1330-7 1001 1663 1250 1067 1150 831 900 48 6030 78
ACS800-17-1510-7 1164 1879 1350 1206 1300 940 1050 51 6030 78
ACS800-17-1980-7 1536 2480 1850 1591 1750 1240 1350 67 7530 79
ACS800-17-2780-7 2091 3472 2600 2228 2450 1736 1900 94 10550 79
ACS800-17-2940-7 2280 3680 2800 2362 2550 1840 2000 99 11300 79
PDM-184674-E51
Technical data
139
Symbols
Nominal ratings
I1N Nominal input current
Imax Maximum output current. Allowable for 10 seconds at start, otherwise as long as allowed
by drive temperature.
Pcont.max Typical motor power. The power ratings apply to most 4-pole NEMA-rated motors at
nominal voltage (460 or 575 V).
Normal use (10% overloadability)
I2N Continuous rms current. 10% overload is allowed for 1 minute every 5 minutes.
PN Typical motor power. The power ratings apply to most 4-pole NEMA-rated motors at
Heavy-duty use (50% overloadability)
I2hd Continuous rms current. 50% overload is allowed for 1 minute every 5 minutes.
Phd Typical motor power. The power ratings apply to most 4-pole NEMA-rated motors at
Note: The ratings apply at an ambient temperature of 40 °C (104 °F). At lower

temperatures, the ratings are higher.
ACS800-17 frame sizes and power module types
Supply module(s) used* LCL filter(s) used Inverter modules used*

ACS800-17 type Frame size
Qty Type Qty Type Qty Type
ACS800-17-0060-3 R6 1 ACS800-11-0060-3** N/A N/A
ACS800-17-0070-3 R6 1 ACS800-11-0070-3** N/A N/A
ACS800-17-0100-3 R6 1 ACS800-11-0100-3** N/A N/A
ACS800-17-0140-3 R7i 1 ACS800-104-0145-3 1 ALCL-04-5 1 ACS800-104-0145-3
ACS800-17-0210-3 R8i 1 ACS800-104-0260-3+E205 1 ALCL-12-5 1 ACS800-104-0210-3
ACS800-17-0640-3 2×R8i 2 ACS800-104-0390-3+E205 1 ALCL-24-5 2 ACS800-104-0320-3+E205
Three-phase supply voltage 380 V, 400 V, 415 V, 440 V, 460 V, 480 V or 500 V
ACS800-17-0070-5 R6 1 ACS800-11-0070-5** N/A N/A
ACS800-17-0100-5 R6 1 ACS800-11-0100-5** N/A N/A
ACS800-17-0120-5 R6 1 ACS800-11-0120-5** N/A N/A
Technical data
140
Supply module(s) used* LCL filter(s) used Inverter modules used*

ACS800-17 type Frame size
Qty Type Qty Type Qty Type
Three-phase supply voltage 525 V, 550 V, 575 V, 600 V, 660 V, or 690 V
ACS800-17-0060-7 R6 1 ACS800-11-0060-7** N/A N/A
ACS800-17-0070-7 R6 1 ACS800-11-0070-7** N/A N/A
ACS800-17-0100-7 R6 1 ACS800-11-0100-7** N/A N/A
ACS800-17-0260-7 R8i 1 ACS800-104-0260-7+E205 1 ALCL-12-7 1 ACS800-104-0260-7+E205
*Modules come with delivery-specific options.
**Integrated supply module, LCL filter and inverter module
PDM-184674-B2
AC fuses
Notes:
• Larger fuses must not be used.
• Fuses from other manufacturers can be used if they meet the ratings.
• The recommended fuses are for branch circuit protection per NEC as required for
UL approval.
AC fuse information
Drive type aR, IEC aR, UL Recognized
Qty In
Bussmann Mersen Bussmann Mersen
400 V
ACS800-17-0060-3 3 160 170M3814 – 170M3014 –
ACS800-17-0070-3 3 200 170M3815 – 170M3015 –
ACS800-17-0100-3 3 250 170M3816 – 170M3016 –
ACS800-17-0140-3 3 315 170M3817 – 170M3017 –
ACS800-17-0170-3 3 400 170M5808 – 170M5008 –
ACS800-17-0210-3 3 450 170M5809 6.9URD2PV0450 170M5059 –
ACS800-17-0260-3 3 630 170M6810 6.9URD3PV0630 170M6210 –
ACS800-17-0320-3 3 800 170M8545 6.9URD3PV0800 170M6212 –
ACS800-17-0390-3 3 1000 170M6814 6.9URD3PV1000 170M6214 –
ACS800-17-0490-3 3 1000 170M6814 6.9URD3PV1000 170M6214 –
ACS800-17-0640-3 3 1600 170M6419 6URD33TTF1600 170M6419 6URD33TTF1600
ACS800-17-0770-3 3 2000 170M6421 5.5URD33TTF2000 170M6421 5.5URD33TTF2000
Technical data
141
AC fuse information
Drive type aR, IEC aR, UL Recognized
Qty In
Bussmann Mersen Bussmann Mersen
500 V
ACS800-17-0070-5 3 160 170M3814 – 170M3014 –
ACS800-17-0100-5 3 200 170M3815 – 170M3015 –
ACS800-17-0120-5 3 250 170M3816 – 170M3016 –
ACS800-17-0170-5 3 315 170M3817 – 170M3017 –
ACS800-17-0210-5 3 400 170M5808 – 170M5008 –
ACS800-17-0260-5 3 450 170M5809 6.9URD2PV0450 170M5059 –
ACS800-17-0320-5 3 630 170M6810 6.9URD3PV0630 170M6210 –
ACS800-17-0400-5 3 800 170M8545 6.9URD3PV0800 170M6212 –
ACS800-17-0460-5 3 1000 170M6814 6.9URD3PV1000 170M6214 –
ACS800-17-0510-5 3 1000 170M6814 6.9URD3PV1000 170M6214 –
ACS800-17-0580-5 3 1000 170M6814 6.9URD3PV1000 170M6214 –
690 V
ACS800-17-0060-7 3 100 170M3812D – 170M3012 –
ACS800-17-0070-7 3 125 170M3813D – 170M3013 –
ACS800-17-0100-7 3 160 170M3814D – 170M3014 –
ACS800-17-0160-7 3 250 170M3816 – 170M3016 –
ACS800-17-0200-7 3 315 170M3817 – 170M3017 –
ACS800-17-0260-7 3 315 170M3817 6.9URD1PV0315 170M3017 –
ACS800-17-0320-7 3 450 170M5809 6.9URD2PV0450 170M5059 –
ACS800-17-0400-7 3 450 170M5809 6.9URD2PV0450 170M5059 –
ACS800-17-0440-7 3 630 170M6810 6.9URD3PV0630 170M6210 –
ACS800-17-0540-7 3 630 170M6810 6.9URD3PV0630 170M6210 –
ACS800-17-0870-7 3 1250 170M6416 – 170M6416 –
ACS800-17-1050-7 3 1250 170M6416 – 170M6416 –
ACS800-17-1980-7 6 1250 170M6416 – 170M6416 –
ACS800-17-2780-7 9 1250 170M6416 – 170M6416 –
ACS800-17-2940-7 9 1250 170M6416 – 170M6416 –
PDM-184674-D
Technical data
142
DC fuses
Notes:
• Larger fuses must not be used.
• Fuses from other manufacturers can be used if they meet the ratings.
• The recommended fuses are for branch circuit protection per NEC as required for
UL approval.
DC fuse information
Drive type IEC UL Recognized
Qty
Bussmann Mersen In Bussmann In
400 V
ACS800-17-0060-3
… – – – – – –
ACS800-17-0490-3
ACS800-17-0640-3 8 170M8552 6.9URD3PV1000 1000 170M6215 1000
ACS800-17-0770-3 8 170M8547 6.9URD33PA1250 1250 170M6216 1250
ACS800-17-0960-3 8 170M8547 6.9URD33PA1250 1250 170M6216 1250
ACS800-17-1070-3 12 170M8552 6.9URD3PV1000 1000 170M6215 1000
ACS800-17-1370-3 12 170M8547 6.9URD33PA1250 1250 170M6216 1250
ACS800-17-1810-3 16 170M8547 6.9URD33PA1250 1250 170M6216 1250
500 V
ACS800-17-0070-5
… – – – – – –
ACS800-17-0580-5
ACS800-17-0780-5 8 170M8552 6.9URD3PV1000 1000 170M6215 1000
ACS800-17-0870-5 8 170M8552 6.9URD3PV1000 1000 170M6215 1000
ACS800-17-1140-5 8 170M8547 6.9URD33PA1250 1250 170M6216 1250
ACS800-17-1330-5 12 170M8547 6.9URD33PA1250 1250 170M6215 1250
ACS800-17-1640-5 12 170M8547 6.9URD33PA1250 1250 170M6216 1250
ACS800-17-2160-5 16 170M8547 6.9URD33PA1250 1250 170M6216 1250
690 V
ACS800-17-0060-7
… – – – – – –
ACS800-17-0540-7
ACS800-17-0790-7 8 170M8646 12URD73PA0700 700 170M8636 700
ACS800-17-0870-7 8 170M8647 11URD73PA0800 800 170M8637 800
ACS800-17-1050-7 8 170M8647 11URD73PA0800 800 170M8637 800
ACS800-17-1330-7 12 170M8647 11URD73PA0800 800 170M8637 800
ACS800-17-1510-7 12 170M8647 11URD73PA0800 800 170M8637 800
ACS800-17-1980-7 16 170M8647 11URD73PA0800 800 170M8637 800
ACS800-17-2780-7 24 170M8647 11URD73PA0800 800 170M8637 800
ACS800-17-2940-7 24 170M8647 11URD73PA0800 800 170M8637 800
PDM-184674-D
Technical data
143
Input power connection

Voltage (U1) 380/400/415 V AC 3-phase ± 10% for 400 V AC units
380/400/415/440/460/480/500 V AC 3-phase ± 10% for 500 V AC units
525/550/575/600/660/690 V AC 3-phase ± 10% for 690 V AC units
Short-circuit withstand Units without grounding switch: Maximum allowable prospective short-circuit current is
strength (IEC 60439-1) 65 kA when protected by the fuses given in the fuse tables.
Units with grounding switch: Maximum allowable prospective short-circuit current is 50 kA
when protected by the fuses given in the fuse tables.
Short-circuit current The drive is suitable for use on a circuit capable of delivering not more than 100,000 rms
protection (UL 508A) symmetrical amperes at 600 V maximum when protected by the fuses given in the fuse
tables.
Short-circuit current The drive is suitable for use on a circuit capable of delivering not more than 65 kA rms
protection (CSA C22.2 No. symmetrical amperes at 600 V maximum when protected by the fuses given in the fuse
14-05) tables.
Frequency 48…63 Hz
Imbalance Max. ± 3% of nominal phase-to-phase input voltage
Voltage dips Max. 25%
Power factor cosphi = 1.00 (fundamental at nominal load)

I1
- ⋅ cosphi > 0.98
-------- I1 = fundamental input current rms value
I rms
Irms = total input current rms value
Harmonic distortion Harmonics are below the limits defined in IEEE519 for all Isc/IL. Each individual harmonic
current fulfils IEEE519 table 10-3 for Isc/IL > 20. Current THD and each individual current
harmonic fulfil IEC 61000-3-4 table 5.2 for Rsce > 66. The values will be met if the supply
network voltage is not distorted by other loads and when the drive operates at the nominal
load.
Input power cable lead- Ø60 mm. For quantity and location, see chapter Dimensions.
throughs
Technical data
144
Input terminals L1/L2/L3 – Bottom cable entry/exit

Frame R6
Front view
Bolt size: M10
Tightening torque: 40 Nm (29.5 lbf.ft)
Top cable entry/exit

Front view
Bolt size: M10
Input terminals L1/L2/L3 – Side view

Frame R7i Bolt size: M12 or ½”
Tightening torque: 70 Nm (52 lbf.ft)
Technical data
145
Input terminals L1/L2/L3 – Front view

Frame R8i Bolt size: M12 or ½”
Input terminals L1/L2/L3 – Front view

Frame 2×R8i and up Bolt size: M12 or ½”
Motor connection
Voltage (U2) 0 to U1, 3-phase symmetrical, Umax at the field weakening point
Frequency DTC mode: 0 to 3.2 × fFWP. Maximum frequency 300 Hz.
UNmains
fFWP = · fNmotor
UNmotor
where fFWP = frequency at field weakening point; UNmains = mains (input power) voltage;
UNmotor = rated motor voltage; fNmotor = rated motor frequency
Frequency resolution 0.01 Hz
Current See section IEC ratings.
Power limit 2 × Phd. After approximately 2 minutes at 2 × Phd, the limit is set at Pcont.max.
Field weakening point 8 to 300 Hz
Switching frequency 2…3 kHz (average)
Motor cable lead-throughs 3 × Ø60 mm at each inverter module (units without common motor terminal cubicle)
Units with common motor terminal cubicle: See chapter Dimensions.
Technical data
146
Output terminals U2/V2/W2 Bottom cable entry/exit

– Frame R6
Front view
Bolt size: M10
Top cable entry/exit

Front view
Bolt size: M10
Output terminals U2/V2/W2 Front view

– Frame R7i Bolt size: M12 or ½”
Technical data
147
Standard output terminals Bottom or top exit

U2/V2/W2 – Frame R8i Front view
Frame R8i units without option Bolt size: M12 or ½”
+E202 (EMC/RFI filtering for Tightening torque: 70 Nm (52 lbf.ft)
1st Environment) or +H359
(common motor terminal
cubicle)
Output terminals at each R8i

Bottom exit Top exit
inverter module
Side view Side view
Frame R8i units with option Bolt size: M12 or ½” Bolt size: M12 or ½”
+E202 (EMC/RFI filtering for Tightening torque: 70 Nm (52 lbf.ft) Tightening torque: 70 Nm (52 lbf.ft)
1st Environment) but without
option +H359 (common motor
terminal cubicle)
Frame 2×R8i and larger units
without option +H359
Cabling
direction
Cabling direction
68265631-B cabinet_400_generic.asm
Output terminals 8 × Ø13 mm per phase. Tightening torque: 70 Nm (52 lbf.ft). See chapter Dimensions.
Units with option +H359
(common motor terminal
cubicle)
Technical data
148
Maximum recommended 100 m (328 ft).

motor cable length Motor cables up to 300 m (984 ft) long are allowed for frames R6 and R7i, and up to 500 m
(1640 ft) long for frames R8i and up, but then EMC filtering within the specified limits will
not be realised.
Efficiency
> 97% (at rated current and nominal supply voltage)
Cooling
Method Internal fans, flow direction from bottom to top
Filter material Inlet (door) Outlet (roof)

IP22/IP42 units Luftfilter airTex G150 –
IP54 units Luftfilter airComp 300-50 Luftfilter airTex G150
Free space around the unit See chapter Mechanical installation.
Cooling air flow See IEC ratings.
Degrees of protection
IP21; IP22; IP42; IP54, IP54R (with air outlet duct)
Ambient conditions
Environmental limits for the drive are given below. The drive must be used in a heated,
indoor controlled environment.
Operation Storage Transportation
installed for stationary use in the protective package in the protective package
Installation site altitude Supply voltage < 600 V AC: - -
max. 4000 m, except drives
with options +Q963, +Q964
and +Q968: max. 2000 m
Supply voltage > 600 V AC
(max. 690 V AC):
- IT (ungrounded) and
corner-grounded networks:
max. 2000 m
- TN (grounded) networks:
max. 4000, except drives
with options +Q963, +Q964
and +Q968: max. 2000 m
Note: Above 1000 m
(3281 ft), see section
Derating.
Air temperature -15 to +50 °C (5 to 122 °F), -40 to +70 °C (-40 to +158°F) -40 to +70 °C (-40 to +158°F)
no frost allowed. See section
Derating.
Technical data
149
Relative humidity 5 to 95% Max. 95% Max. 95%

No condensation allowed. Maximum allowed relative humidity is 60% in the presence of
corrosive gases.
Contamination levels No conductive dust allowed.
(IEC 60721-3-3, IEC 60721-3- Boards without coating: Boards without coating: Boards without coating:
2, IEC 60721-3-1) Chemical gases: Class 3C1 Chemical gases: Class 1C2 Chemical gases: Class 2C2
Solid particles: Class 3S2 Solid particles: Class 1S3 Solid particles: Class 2S2
Boards with coating: Boards with coating: Boards with coating:
Chemical gases: Class 3C2 Chemical gases: Class 1C2 Chemical gases: Class 2C2
Solid particles: Class 3S2 Solid particles: Class 1S3 Solid particles: Class 2S2
Atmospheric pressure 70 to 106 kPa 70 to 106 kPa 60 to 106 kPa
0.7 to 1.05 atmospheres 0.7 to 1.05 atmospheres 0.6 to 1.05 atmospheres
Vibration (IEC 60068-2) Max. 1 mm (0.04 in.) Max. 1 mm (0.04 in.) Max. 3.5 mm (0.14 in.)
(5 to 13.2 Hz), (5 to 13.2 Hz), (2 to 9 Hz),
max. 7 m/s2 (23 ft/s2) max. 7 m/s2 (23 ft/s2) max. 15 m/s2 (49 ft/s2)
(13.2 to 100 Hz) sinusoidal (13.2 to 100 Hz) sinusoidal (9 to 200 Hz) sinusoidal
Shock (IEC 60068-2-27) Not allowed Max. 100 m/s2 (330 ft./s2), Max. 100 m/s2 (330 ft./s2),
11 ms 11 ms
Free fall Not allowed 100 mm (4 in.) for weight 100 mm (4 in.) for weight
over 100 kg (220 lb) over 100 kg (220 lb)
Materials
Cabinet Hot-dip zinc-coated (thickness approx. 20 µm) steel sheet (thickness 1.5 mm) with
polyester thermosetting powder coating (thickness approx. 80 µm) on visible surfaces.
Colour: RAL 7035 (light grey, semigloss).
Busbars Tin- or silver-plated copper
Fire safety of materials Insulating materials and non-metallic items: Mostly self-extinctive
(IEC 60332-1)
Packaging Frame: Wood or plywood. Plastic wrapping: PE-LD. Bands: PP or steel.
Disposal The drive contains raw materials that should be recycled to preserve energy and natural
resources. The package materials are environmentally compatible and recyclable. All
metal parts can be recycled. The plastic parts can either be recycled or burned under
controlled circumstances, according to local regulations. Most recyclable parts are marked
with recycling marks.
If recycling is not feasible, all parts excluding electrolytic capacitors and printed circuit
boards can be landfilled. The DC capacitors (C1-1 to C1-x) contain electrolyte and the
printed circuit boards contain lead, both of which are classified as hazardous waste within
the EU. They must be removed and handled according to local regulations.
For further information on environmental aspects and more detailed recycling instructions,
please contact your local ABB distributor.
Technical data
150
Tightening torques for power connections

Screw size Torque
M5 3.5 Nm (2.6 lbf.ft)
M6 9 Nm (6.6 lbf.ft)
M8 20 Nm (14.8 lbf.ft)
M10 40 Nm (29.5 lbf.ft)
M12 70 Nm (52 lbf.ft)
M16 180 Nm (133 lbf.ft)
Applicable standards
The drive complies with the following standards. The compliance with the European Low
Voltage Directive is verified according to standards EN 61800-5-1 and EN 60204-1.
• EN 61800-5-1:2007 Adjustable speed electrical drives. Part 5-1: Safety requirements. Electrical, thermal and
energy.
• EN 60204-1:2006 + Safety of machinery. Electrical equipment of machines. Part 1: General requirements.
A1:2009 Provisions for compliance: The final assembler of the machine is responsible for installing
- an emergency-stop device
- a supply disconnecting device
- the drive module into a cabinet.
• EN 60529:1991 (IEC 60529) Degrees of protection provided by enclosures (IP code)
• IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems. Part 1: Principles,
requirements and tests.
• EN 61800-3:2004 Adjustable speed electrical power drive systems. Part 3: EMC requirements and specific
test methods.
• UL 508C:2002, Third Edition UL Standard for Safety, Power Conversion Equipment
• CSA C22.2 No. 14-10 Industrial control equipment
Technical data
151
CE marking
A CE mark is attached to the drive to verify that the unit follows the provisions of the European Low
Voltage, and EMC Directives. The CE marking also verifies that the drive, in regard to its safety
functions (such as Safe torque off), conforms with the Machinery Directive as a safety component.
Compliance with the European Low Voltage Directive

The compliance with the European Low Voltage Directive has been verified according to standards
EN 60204-1 and EN 61800-5-1.
Compliance with the European EMC Directive

The EMC Directive defines the requirements for immunity and emissions of electrical equipment used
within the European Union. The EMC product standard (EN 61800-3:2004) covers requirements stated
for drives. See section Compliance with EN 61800-3:2004 on page 154.
Compliance with the European Machinery directive

The drive is an electronic product which is covered by the European Low Voltage Directive. However,
the drive can be equipped with the Safe torque off function and other safety functions for machinery
which, as safety components, are in the scope of the Machinery Directive. These functions of the drive
comply with European harmonized standards such as EN 61800-5-2. The declaration of conformity for
each function is in the appropriate function-specific manual.
Technical data
152
Declaration of Conformity
Technical data
153
Technical data
154
Compliance with EN 61800-3:2004
Definitions
EMC stands for Electromagnetic Compatibility. It is the ability of electrical/electronic equipment to
operate without problems within an electromagnetic environment. Likewise, the equipment must not
disturb or interfere with any other product or system within its locality.
First environment includes establishments connected to a low-voltage network which supplies buildings
used for domestic purposes.
Second environment includes establishments connected to a network not supplying domestic premises.
Drive of category C2: drive of rated voltage less than 1000 V and intended to be installed and
commissioned only by a professional when used in the first environment. Note: A professional is a
person or organisation having necessary skills in installing and/or commissioning power drive systems,
including their EMC aspects.
Drive of category C3: drive of rated voltage less than 1000 V and intended for use in the second
environment and not intended for use in the first environment.
Drive of category C4: drive of rated voltage equal to or above 1000 V, or rated current equal to or above
400 A, or intended for use in complex systems in the second environment.
Category C2
The drive complies with the standard with the following provisions:
1. The drive is equipped with EMC filter +E202.
2. The motor and control cables are selected as specified in the Hardware Manual.
3. The drive is installed according to the instructions given in the Hardware Manual.
4. Maximum motor cable length is 100 metres (328 ft).
WARNING! The drive may cause radio interference if used in a residential or domestic environment.
The user is required to take measures to prevent interference, in addition to the requirements for CE
compliance listed above, if necessary.
Note: It is not allowed to install a drive equipped with EMC filter +E202 on IT (ungrounded) systems.
The supply network becomes connected to ground potential through the EMC filter capacitors which
may cause danger or damage the unit. See also section IT (ungrounded) systems on page 82.
Category C3
The drive complies with the standard with the following provisions:
1. The drive of frame size R6 is equipped with optional EMC filter +E200. (Frame sizes R7i and R8i
have EMC filter +E210 as standard equipment, and thus, they meet the Category 3 requirements as
default.) See also section IT (ungrounded) systems on page 82.
3. Maximum motor cable length is 100 metres (328 ft).
WARNING! A drive of category C3 is not intended to be used on a low-voltage public network which
supplies domestic premises. Radio frequency interference is expected if the drive is used on such a
network.
Note: It is not allowed to install a drive equipped with EMC filter +E200 on IT (ungrounded) systems.
The supply network becomes connected to ground potential through the EMC filter capacitors which
may cause danger or damage the unit. See also section IT (ungrounded) systems on page 82.
Technical data
155
Category C4
If the provisions under Category C3 cannot be met, the use of the drive in the second environment is
also possible if:
1. It is ensured that no excessive emission is propagated to neighbouring low-voltage networks. In
some cases, the natural suppression in transformers and cables is sufficient. If in doubt, the supply
transformer with static screening between the primary and secondary windings can be used.
Medium voltage network

Supply transformer
Neighbouring network
Static screen
Point of measurement
Low voltage Low voltage

Equipment
Drive
(victim)
Equipment Equipment
2. An EMC plan for preventing disturbances is drawn up for the installation. A template is available
from the local ABB representative.
WARNING! A drive of category C4 is not intended to be used on a low-voltage public network which
supplies domestic premises. Radio frequency interference is expected if the drive is used on such a
network.
“C-tick” marking
“C-tick” marking is required in Australia and New Zealand. A “C-tick” mark is attached to each drive in
order to verify compliance with the relevant standard (IEC 61800-3:2004 – Adjustable speed electrical
power drive systems. Part 3: EMC product standard including specific test methods), mandated by the
Trans-Tasman Electromagnetic Compatibility Scheme. See section Compliance with EN 61800-3:2004
on page 154.
Technical data
156
Technical data
157
Dimensions

This chapter contains tables of cabinet line-ups as well as dimensional drawings of
the different frame sizes of the ACS800-17.
Cabinet line-ups
The drive consists of cubicles built into a cabinet line-up. The tables below show the
composition of cabinet line-ups for each frame size and the standard combinations
of options. The dimensions are in millimetres.
Notes:
• The side panels increase the total line-up width by 30 millimetres (1.2”).
• The standard depth of the cabinet line-up is 650 mm (excluding door equipment
such as switches and air inlet gratings). This is increased by 130 millimetres
(5.1”) with top entry/exit models as well as units with cooling air intake through the
bottom of the cabinet.
• The measurements given apply to 6-pulse-input, non-UL/CSA units. For
dimensions of 12-pulse-input or UL/CSA units, contact your local ABB
representative.
The tables are followed by example dimensional drawings.
R6
Width Net weight
(kg approx.)
400 300
R7i
Drive Common Sine filter Line-up Net weight
motor cubicle width (kg approx.)
terminal
cubicle*
600 600 400
600 300** 300 900 480
600 400** 1000 650
*Added with filter options +E202 or +E205 if option +E206 (sine filter)
is not present. +H359 is not available without +E202/+E205.
**The output (motor) terminals are contained within this cubicle.
Dimensions
158
R8i
Input/Output Supply and Common Sine filter Line-up Net weight
cubicle inverter motor cubicle width (kg approx.)
unit cubicle terminal
cubicle*
400 800 1200 950
400 800 300** 1500 1030
400 800 400** 1600 1200
*Added with filter option +E202 if option +E206 (sine filter) is not present.
+H359 is not available without +E202.
**The output (motor) terminals are contained within this cubicle.
2×R8i
Incoming cubicle
Auxiliary control/
terminal cubicle
Common motor
Shipping split 1
Shipping split 2
Joining cubicle
EMC/RFI filter
Line-up width
(kg approx.)
Inverter unit
Supply unit
Net weight
Sine filter
Sine filter
cubicle 1
cubicle 2
cubicle
cubicle
cubicle
width
width
1000 800 600 2400 2400 1910
1000 800 600 300 2700 2700 1975
1000 300 800 600 2700 2700 1990
1000 300 800 600 300 3000 3000 2070
1000 800 600 1000 3400 3400 2360
1000 300 800 600 1000 3700 3700 2440
1000 800 600 300 1000 1000 2400 2300 4700 2875
3×R8i
Incoming cubicle
Auxiliary control/
terminal cubicle
Common motor
Shipping split 1
Shipping split 2
Joining cubicle
Line-up width
(kg approx.)
Inverter unit
Supply unit
Supply unit
Net weight
Sine filter
Sine filter
cubicle 1
cubicle 2
cubicle 1
cubicle 2
cubicle
width
width
1000 600 800 800 3200 3200 2170

1000 600 800 800 300 3500 3500 2235
1000 600 800 800 1000 4200 4200 2620
1000 600 800 800 300 1000 1000 3200 2300 5500 3135
Dimensions
159
4×R8i
Incoming cubicle
Auxiliary control/
terminal cubicle
Common motor
Shipping split 1
Shipping split 2
Joining cubicle
Line-up width
(kg approx.)
Inverter unit
Inverter unit
Supply unit
Supply unit
Net weight
Sine filter
Sine filter
Sine filter
Top entry
cubicle 1
cubicle 2
cubicle 1
cubicle 2
cubicle 1
cubicle 2
cubicle 3
width
width
1000 800 800 600 600 3800 3800 3380
1000 300 800 800 600 600 4100 4100 3460
1000 800 800 600 600 400 4200 4200 3455
1000 300 800 800 600 600 * 400* 3900 600 4500 3535
1000 800 800 600 600 300 1000 1000 3800 2300 6100 4360
1000 300 800 800 600 600 300 1000 1000 4100 2300 6400 4440
1000 800 800 600 600 300 1000 1000 1000 3800 3300 7100 4810
1000 300 800 800 600 600 300 1000 1000 1000 4100 3300 7400 4890
*The common motor terminal cubicle also acts as a joining cubicle.
5×R8i
Incoming cubicle
Joining cubicle 1
Joining cubicle 2
Auxiliary control/
terminal cubicle
Common motor
Shipping split 1
Shipping split 2
Shipping split 3
Line-up width
(kg approx.)
Inverter unit
Inverter unit
Supply unit
Supply unit
Supply unit
Net weight
Sine filter
Sine filter
Sine filter
Top entry
cubicle 1
cubicle 2
cubicle 3
cubicle 1
cubicle 2
cubicle 1
cubicle 2
cubicle 3
width
width
width
1000 800 800 800 800 600 300 3700 1400 5100 4270
1000 300 800 800 800 800 600 300 4000 1400 5400 4350
1000 800 800 800 800 600 * 600* 3400 2000 5400 4305
1000 300 800 800 800 800 600 * 600* 3700 2000 5700 4385
1000 800 800 800 800 600 300 300 1000 1000 1000 3700 1400 3300 8400 5700
1000 300 800 800 800 800 600 300 300 1000 1000 1000 4000 1400 3300 8700 5780
6×R8i
Incoming cubicle
Joining cubicle 1
Joining cubicle 2
Auxiliary control/
terminal cubicle
Common motor
Shipping split 1
Shipping split 2
Shipping split 3
Line-up width
(kg approx.)
Inverter unit
Inverter unit
Supply unit
Supply unit
Supply unit
Net weight
Sine filter
Sine filter
Sine filter
Top entry
cubicle 1
cubicle 2
cubicle 3
cubicle 1
cubicle 2
cubicle 1
cubicle 2
cubicle 3
width
width
width
1000 800 800 800 800 800 300 3700 1600 5300 4420
1000 300 800 800 800 800 800 300 4000 1600 5600 4500
1000 800 800 800 800 800 * 600* 3400 2200 5600 4455
1000 300 800 800 800 800 800 * 600* 3700 2200 5900 4535
1000 800 800 800 800 800 300 300 1000 1000 1000 3700 1600 3300 8600 5850
1000 300 800 800 800 800 800 300 300 1000 1000 1000 4000 1600 3300 8900 5930
Dimensions
160
Frame R6
Dimensions
161
[Frame R6 continued]
Dimensions
162
Frame R7i
Dimensions
163
[Frame R7i continued]
Dimensions
164
Dimensions
165
Dimensions
166
Dimensions
167
Frame R7i with +E202/+E205/+H359
Dimensions
168
[Frame R7i with +E202/+E205/+H359 continued]
Dimensions
169
Dimensions
170
Dimensions
171
Dimensions
172
Dimensions
173
Dimensions
174
Dimensions
175
Frame R7i, marine construction (+C121)
Dimensions
176
[Frame R7i, marine construction (+C121) continued]
Dimensions
177
[Frame R7i, marine construction (+C121) continued]
Dimensions
178
Frame R8i
Dimensions
179
Dimensions
180
Dimensions
181
Dimensions
182
Dimensions
183
Dimensions
184
Frame R8i with +E202/+H359
Dimensions
185
[Frame R8i with +E202/+H359 continued]
Dimensions
186
Frame 2×R8i
Dimensions
187
[Frame 2×R8i continued]
Dimensions
188
Dimensions
189
Dimensions
190
Dimensions
191
Dimensions
192
Dimensions
193
Dimensions
194
Dimensions
195
Dimensions
196
Frame 3×R8i
Dimensions
197
Dimensions
198
Dimensions
199
Dimensions
200
Dimensions
201
Dimensions
202
Frame 4×R8i
Dimensions
203
Dimensions
204
Dimensions
205
Dimensions
206
Dimensions
207
Dimensions
208
Frame 5×R8i
Dimensions
209
Dimensions
210
Dimensions
211
Dimensions
212
Dimensions
213
Dimensions
214
Dimensions
215
Dimensions
216
Dimensions
217
Dimensions
218
Dimensions
219
Dimensions
220
Frame 6×R8i
Dimensions
221
Dimensions
222
Dimensions
223
Dimensions
224
Dimensions
225
Dimensions
226
Dimensions
227
Dimensions
228
Dimensions
229
Dimensions
230
Dimensions
231
Dimensions
232
Dimensions
233
234
Further information
Product and service inquiries
Address any inquiries about the product to your local ABB representative, quoting the type
designation and serial number of the unit in question. A listing of ABB sales, support and service
contacts can be found by navigating to www.abb.com/drives and selecting Sales, Support and
Service network.
Product training
For information on ABB product training, navigate to www.abb.com/drives and select Training
courses.
Providing feedback on ABB Drives manuals

Your comments on our manuals are welcome. Go to www.abb.com/drives and select Document
Library – Manuals feedback form (LV AC drives).
Document library on the Internet

You can find manuals and other product documents in PDF format on the Internet. Go to
www.abb.com/drives and select Document Library. You can browse the library or enter selection
criteria, for example a document code, in the search field.
Contact us
3AFE68397260 Rev E (EN) 2013-02-14

www.abb.com/drives
www.abb.com/drivespartners

En Acs800 17 Hwman e Scrres

Uploaded by

Copyright:

Available Formats

En Acs800 17 Hwman e Scrres

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

En Acs800 17 Hwman e Scrres

Uploaded by

Copyright:

Available Formats

ACS800

Drive (inverter) firmware manuals and guides

Option manuals and guides

© 2013 ABB Oy. All Rights Reserved.

What this chapter contains

Usage of warnings and notes

Dangerous voltage warning warns of high voltages which can cause

General warning warns about conditions, other than those caused by

Installation and maintenance work

• Apply temporary grounding before working on the unit.

• After maintaining or modifying a drive safety circuit or changing circuit boards

• The brake control terminals (UDC+, UDC-, R+ and R- terminals) carry a

• Depending on the external wiring, dangerous voltages (115 V, 220 V or 230 V)

• The Prevention of unexpected start-up function (option +Q950) does not

• Fastening the cabinet by riveting or welding is not recommended. However, if

• Ensure sufficient cooling of the unit.

• Some parts inside the drive cabinet, such as heatsinks of power

• The printed circuit boards contain components sensitive to electrostatic

• Make sure that grounding conductors are adequately sized as required by

• In a multiple-drive installation, connect each drive separately to protective

• Do not install a drive equipped with an EMC (line) filter to an ungrounded

• As the normal leakage current of the drive is higher than 3.5 mA AC or

Fibre optic cables

Permanent magnet motor drives

Installation and maintenance work

Inverter control program

About this manual

Door switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

Planning the electrical installation

Permanent magnet synchronous motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Input power connection – Frame R8i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86

Motor control and I/O board (RMIO)

Digital inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Installation checklist and start-up

Power module replacement (Frame R8i and up) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127

About this manual

What this chapter contains

Common chapters for multiple products

Categorization according to the frame size

About this manual

About this manual

Installation and commissioning flowchart

Plan the installation. Technical data

Unpack and check the units. Mechanical installation

Only intact units may be started up.

Check the installation site. Mechanical installation, Technical data

Route the cables. Planning the electrical installation: Routing the

Mount the cabinet line-up. Mechanical installation

Check the installation. Installation checklist and start-up

Commission the drive. Installation checklist and start-up, The ACS800-

About this manual

Terms and abbreviations

APBU Type of optical branching unit used for connecting parallel-connected

CMF Common mode filtering.

DDCS Distributed Drives Communication System; a protocol used in optical fibre

Drive unit See Motor-side converter.

EMC Electromagnetic Compatibility.

Four-quadrant Operation of a machine as a motor or generator in quadrants I, II, III and

IGBT Insulated Gate Bipolar Transistor; a voltage-controlled semiconductor type

About this manual