Service Manual: Viewsonic Vx2433Wm-1 Vx2433Wm-Cn

Service Manual
ViewSonic VX2433wm-1
VX2433wm-CN
Model No. VS12324
23.6” Wide Color TFT LCD Display
(VX2433wm-1_VX2433wm-CN _SM Rev. 1b Feb. 2009)

ViewSonic 381 Brea Canyon Road, Walnut, California 91789 USA - (800) 888-8583
Copyright
Copyright © 2009 by ViewSonic Corporation. All rights reserved. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language or computer language, in any form or by any means, electronic, mechanical, magnetic,
optical, chemical, manual or otherwise, without the prior written permission of ViewSonic
Corporation.
Disclaimer
ViewSonic makes no representations or warranties, either expressed or implied, with respect to
the contents hereof and specifically disclaims any warranty of merchantability or fitness for any
particular purpose. Further, ViewSonic reserves the right to revise this publication and to make
changes from time to time in the contents hereof without obligation of ViewSonic to notify any
person of such revision or changes.
Trademarks
Optiquest is a registered trademark of ViewSonic Corporation.
ViewSonic is a registered trademark of ViewSonic Corporation.
All other trademarks used within this document are the property of their respective owners.
Product disposal at end of product life

The lamp in this product contains mercury. Please dispose of in accordance with local, state or
federal laws.
Revision History
Revision SM Editing Date ECR Number Description of Changes Editor
1a 11/27/2008 Initial Release Eden Chang
Revise “5.7.2 Using Novatek ISP Tool Update

1b 2/10/2009 Eden Chang
FW” item
VX2433wm-1
ViewSonic Corporation i CONFIDENTIAL – DO NOT COPY VX2433wm-CN
TABLE OF CONTENTS
1. Precautions and Safety Notices ......................................................................................... 1
2. Specification ....................................................................................................................... 4
3. Front Panel Function Control Description ..................................................................... 13
4. Circuit Description ............................................................................................................. 17
5. Adjusting Procedure.......................................................................................................... 27
6. Trouble Shooting Flow Chart ............................................................................................ 33
7. Block Diagrams ................................................................................................................ 40
8. Schematic Diagrams ........................................................................................................ 50
9. PCB Layout Diagrams ...................................................................................................... 56
10. Exploded Diagram And Spare Parts List........................................................................ 60
11. Recommended Spare Parts List .................................................................................... 71
VX2433wm-1
ViewSonic Corporation ii CONFIDENTIAL – DO NOT COPY VX2433wm-CN
1. Precautions and Safety Notices
1. SAFETY PRECAUTIONS
This monitor is manufactured and tested on a ground principle that a user’s safety comes first. However,
improper used or installation may cause damage to the monitor as well as to the user.
WARNINGS:
z This monitor should be operated only at the correct power sources indicated on the label on the rear
of the monitor. If you’re unsure of the power supply in you residence, consult your local dealer or
Power Company.
z Use only the special power adapter that comes with this monitor for power input.
z Do not try to repair the monitor by yourself, as it contains no user-serviceable parts. Only the
qualified technician can repair it.
z Do not remove the monitor cabinet. There are high-voltage parts inside that may cause electric shock
to human bodies.
z Stop using the monitor if the cabinet is damaged. Have it checked by a service technician.
z Put your monitor only in a lean, cool, dry environment. If it gets wet, unplug the power cable
immediately and consult your closed dealer.
z Always unplug the monitor before cleaning it. Clean the cabinet with a clean, dry cloth. Apply
non-ammonia based cleaner onto the cloth, not directly onto the glass screen.
z Do not place heavy objects on the monitor or power cord.
2. PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety visual inspections and the
protection afforded by them cannot necessarily be obtained by using replacement components rated for
higher voltage, wattage, etc. Before replacing any of these components read the parts list in this manual
carefully. The use of substitute replacement parts, which do not have the same safety characteristics as
specified in the parts list, may create shock, fire, or other hazards.
3. SERVICE NOTES
z When replacing parts or circuit boards, clamp the lead wires around terminals before soldering.
z Keep wires away from high voltage, high temperature components and sharp edges.
z Keep wires in their original position so as to reduce interference.
z Adjustment of this product please refers to the user’ manual.
VX2433wm-1
ViewSonic Corporation 1 CONFIDENTIAL – DO NOT COPY VX2433wm-CN
Handling and Placing Methods
VX2433wm-1
VX2433wm-1
2. Specification
2.1 INTRODUCTION
1 LCD PANEL Panel: ʳ CMO (M236H1-L01 ver0.0)
Size ʳ 23.6” Wide Color a-Si TFT Active Matrix LCD
Display area ʳ ʳ 525.22(W) x 297.22(H) mm
Optimum Resolution ʳ 1920x1080(WUXGA)
Pixel Pitch 0.2715(H) x 0.2715(V) mm
Glass Treatment ʳ Anti-Glare, Hard coating (3H),Haze25
Contrast Ratio CR >= 10 1000 :1
Dynamic Contrast ʳ 20000:1 (typ.)
Viewing Angle 170/160 (degrees; typ)
Colors 16.7Mcolors (6 bit +Hi FRC panel)
Luminance 300 cd/m2 @8.0mA(typ.)
Response Time On/Off 5 ms (typ.) /10 ms (max.)
Backlight 4 CCFL
Backlight Life 50000 Hrs (Typ) @7.0mA
Mercury 3.6 mg per lamp(max)
2 INPUT SIGNAL Video RGB Analog (0.7 / 1.0 Vp-p , 75 ohms),
DVI-D / HDMI (TMDS, 100ohms)
Sync Separate Sync / Composite Sync / SOG
Fh = 24 – 83 kHz ; Fv = 50 – 76 Hz
3 COMPATIBILITY PC ʳ PC Compatibles (from VGA up to 1920x1080 Non Interlaced)
Mac Power Mac (up to 1920x1080 )
4 Recommended 1920 x 1080 @ 60Hz

RESOLUTION
Supported Refer to setion 4.4
5
AUDIO Speaker 2W*2
6 CONNECTORS Video ʳ Analog DB-15
ʳ ʳ ʳ ʳ Digital DVI-D
ʳ HDMI ( Supported HDMI ver. 1.3 spec)
Audio Audio Out 3.5 mm jack (blue)
Audio In 3.5 mm jack (green
Power Internal Power Adapter, 3-pin plug (CEE22)
7 POWER Voltage ʳ AC 100-240V (Universal); 50-60 Hz
Consumption Typ/Max 45 W (typ.) / 55 W (Max)
ECO Mode Optimize 37 W (typ.)
Conserve 30 W (typ.)
VX2433wm-1
8 ERGONOMICS Tilt Range ʳ 20 ~ -5 degrees
Swivel N/A
Rotation N/A
Height Adjust N/A
9 CONTROLS Physical Key buttons [ ]
ʳ [ 1 ] [ 2 ] [ź] [Ÿ]
OSD Function Main Menu
ʳ Auto Image Adjust
ʳ Contrast/Brightness
Input Select
D-SUB, DVI,HDMI PC,HDMI AV
Audio Adjust
Volume, Mute
Color Adjust
sRGB, 9300K, 7500K, 6500K, 5000K, User Color [R, G, B]
Information
Manual Image Adjust
H/V Position, Horizontal Size, Fine Tune, Sharpness, Dynamic
Contrast, Response Time, Aspect ratio, Display Mode, Eco mode
Setup Menu
Language Select, Resolution Notice, OSD Position, OSD Time Out,
OSD Background, Sleep
Short cut key Memory Recall
ʳ ʳ
[ 1 ] : Main Menu
[ 2 ] : Input Select
[Dn] : To immediately activate Audio menu.
[up] : To immediately activate Contrast menu. It should be change to
Brightness OSD by push button [2]
[Dn] ( Keep pushing 5 sec) ΚUnder HDMI mode, toggle audio source
between HDMI and jack plug
[Up] or [Dn] : Contrast / Brightness
[Up] + [Dn] :
1. In the CR/ BT menu, Recall Contrast or Brightness to default in its
menu without OSD message.
2. In the Audio menu, Recall both of audio volume and mute to default
without OSD message.
* While OSD menu off, recall CR/ BT/ Audio volume and mute to default
VX2433wm-1
[ 1 ] + [ 2 ] : Toggle 720x400 and 640x400 mode
[ 1 ] + [Up] + [Dn] : Auto White Balance
[ 1 ] + [Dn] : Power Lock
[ 1 ] + [Up] : OSD Lock
[ 2 ] + [Dn] : Toggle DDC/CI and DDC/2B
10 BANDWIDTH Analog : 205 MHz
Digital : 175 MHz
11 OPERATING Temperature ʳ 32°F to 104°F (0°C to 40°C)
CONDITION Humidity 20% to 90% (no condensation)
12 STORAGE / Temperature ʳ -4°F to 140°F (-20°C to 60°C)Γ
SHIPPING Humidity 5% to 90% (no condensation)
CONDITION
13 DIMENSIONS Physical: Display w/ Stand 572 mm (W) x 418 mm (H) x 231mm (D)
(W x H x D) 22.52" (W) x 16.46" (H) x 9.09" (D)
Wall Mount 572 mm (W) x 359 mm (H) x 62.3mm (D)
22.52" (W) x 14.13”" (H) x 2.45" (D)
Packing 632 mm (W) x 482 mm (H) x 152mm (D)
(W x H x D) 24.88" (W) x 18.98" (H) x 5.98" (D)
14 WEIGHT Net 5.04kg(11.11lb)
Gross 7.05kg(15.53lb)
15 REGULATIONS ʳ ʳ UL, CUL, FCC-B (ICES), CB, CE, CES-003B, VCCI ,
Nemko ERGO (MPR II, ISO 13406-2), TUV-S, NOM, GOST-R,
HYGIENIC (20 copies), Energy Star, CCC, BSMI, PSB, C-TICK,
KTL/MIC, SASO, WEEE, RoHS, Ukraine, EPEAT Silver
16 RELIABILITY MTBF ʳ 100,000 Hr (Excluding Panel).
17 POWER SAVING "On" Blue Normal
FUNCTION "Active Off" AMBER Љ1W
“Off” Љ 0.5 W
18 LOGISTICS Container Load 20' 480 sets
40' 1008 sets
Pallet Load 48 sets
VX2433wm-1
UPC Code 20' 76690732861 5
40'
Serial Format VX2433wm-1 R4F
VX2433wm-CN R8W
EDID Code 2238
Country of origin China
19 Wall Mount VESA 100mm x 100mm
20 OTHERS DDC/2B, DDC/CI, HDCP, Detachable Base, KENSINGTON MicroSaver
Security Compatible, WorldWide Model, Vista Premium, SRS WOW
HD,HDMI
21 Package LCD Display
Contents Power Cable
Audio Cable
VGA Cable
DVI Cable
Quick Start Guide ( One
page)
ViewSonic Wizard
CD-ROM
22 EU Packaging Carton -- One piece construction with double wall, 0.72 Kg
Information Plastic Handle -- PE-LD, 11 g
Poly Foam – 100 g
Accessory Plastic Bags -- PE-LD, 3 g
The PE bag that cover monitor -- PE-LD, 25 g
Pallet --
For E/M model:
Solid Wood (Fumigation), 13.6 kg
For A/G/J//K/P model:
Poly-wood, 13.6 kg
Note : P model must use Plywood. And for every P model lot, SI shall provide plywood certification.
VX2433wm-1
2.2 PRODUCT DEFINITION AND SPECIFICATION
Product Name ViewSonic VX2433wm
Oracle P/N VX2433WM/VX2433WM-CN
Model Number VS12324
English, French, German,Italian, Spanish, Finnish,
OSD Languages: 11
Russian Japanese, Korean, S. Chinese, T. Chinese
TFT LCD Panel and Model # 1st panel: CMO M236H1-L01
Scalar Novatek NT68672
Input Signal D-Sub / DVI-D/HDMI
Sync Compatibility Separate Sync/ Composite Sync / SOG
Adapter Internal Power Board
Power Cable Yes
Analog Cable (1.8 m, black), with PC 2001 and Hot Plug
Yes
Detect &DDC
DVI-D Cable(1.8m, black) with PC 2001 Yes
Audio Cable(1.8m, black) with PC 2001 No
MIC Cable(1.8m, black) with PC 2001 No
USB Cable (V2.0) No
English, French, German, Dutch, Finnish, Swedish,
Italian, Spanish, Greek, Russian, Czech, Hungarian,
Turkish, Polish, Romania. Bulgaria, Slovakia, Croatia,
ViewSonic CD Wizard
Serbia, Slovenian, Portuguese, Arabic, Japanese,
Simplified Chinese, Traditional Chinese. Korean ,
Ukrainian
English, French, German, Dutch, Finnish, Swedish,
Italian, Spanish, Greek, Russian, Czech, Hungarian,
ViewSonic Quick Start Guide Turkish, Polish, Romania. Bulgaria, Slovakia, Croatia,
Serbia, Slovenian, Portuguese, Arabic, Japanese,
Simplified Chinese, Traditional Chinese. Korean
Screen Protector Mylar Yes
Energy Star Sticker No
POP Sticker Yes
Service Insert For Region code = M units only
Warranty Card For Region code = G units only
Carton Sticker For Region code = G units only
PE bag of Carton For Region code = G units only
VX2433wm-1
2.3 GENERAL SPECIFICATION
Test Resolution & Frequency 1920x1080 @ 60Hz
Test Image Size Full Size
Factory Default:
Contrast and Brightness Controls
Contrast = 70%, Brightness = 100%
2.4 VIDEO INTERFACE

Input Connector (refer the Appendix A)ʳ Analog = DB-15 (Analog)
Digital = DVI-D (Digital)
HDMI (Digital)
Default Input Connector Defaults to the first detected input
Equal to twice the weight of the monitor for five minutes
Video Cable Strain Relief
Refer to Appendix A;
Video Cable Connector Pin out
Compliant DDC/2B and DDC/CI
Video RGB (Analog)
Video Signals Separate Sync / Composite Sync / SOG
TMDS (Digital)
Video Impedance 75 Ohms (Analog), 100 Ohms (Digital)
Maximum PC Video Signal 950 mV with no damage to monitor
Maximum Mac Video Signal 1250 mV with no damage to monitor
Sync Signals TTL
Compliant with Revision 1.3;
DDC 2B
The DDC communication shall not interrupt when power off.
Compliant with Revision 1.1;
DDC/CI
The DDC communication shall not interrupt when power off.
Digital link protection HDCP
Sync Compatibility Separate Sync / Composite Sync / SOG
Shall be compatible with all PC type computers, Macintosh
Video Compatibility computers, and after
market video cards
Video timing support 480i / 480p @ 60Hz 576i / 576p @ 50Hz

(HDMI) 720p @ 50/60Hz 1080i / 1080p @ 50/60Hz
Resolution Compatibility Refer to Segment 4-5
Exclusions Not compatible with interlaced video
VX2433wm-1
2.5 POWER SUPPLY
Internal Power Supply ILPI-107
Input Voltage Range 90 to 264 VAC
Input Frequency Range 47 to 63 Hertz
Short Circuit Protection Output can be shorted without safety issue
5.0A typical at 24VDC
Over Current Protection
( Protect when short circuit)
Leakage Current 3.5MA (MAX) AT 264VAC / 60HZ
Typical: 80%
Efficiency (at 115VAC Full Load)
Minimum: 75%
Fuse Internal and not user replaceable
Power Output 45 Watts (typ)
Ripple:<3%
Ripple and Noise
Noise: <1%
Max Input AC Current 1.5A (MAX)
80 A MAX./ 240VAC / 50HZ
Inrush Current (Cold Start)
(COLD START AT 25к,FULL LOAD)
Shall start and function properly when under full load, with all
Power Supply Cold Start combinations of input voltage, input frequency, and operating
temperature.
Shall be able to withstand an ANSI/IEEE C62.41-1980 6000V 200
Power Supply Transient Immunity
ampere ring wave transient test with no damage.
Shall be able to withstand ±1KV (L-L) and ±2KV (L-PE)
Power Supply Line Surge Immunity (Refer to EN55024:1998 / CISPR24.1997 / IEC1000-4-5: 1995 /
EN61000-4-5: 1995)
Shall be able to function properly, without reset or visible screen
Power Supply Missing Cycle Immunity artifacts, when ½ cycle of AC power is randomly missing at nominal
input.
The power supply shall not produce audible noise that would be
detectable by the user. Audible shall defined to be in compliance with
Power Supply Acoustics
ISO 7779 (DIN EN27779:1991) Noise measurements of machines
acoustics. Power Switch noise shall not be considered.
Power Saving Operation(Method) VESA DPMS Signaling
Power
Mode LED
Consumption
45W(typ)
On BLUE
Power Consumption 55W(max)
ECO Mode Blue 37W (Optimize)
30 W (Conserve)
Active off Amber <1 W
Off Off <0.5W
Recovery Time On Mode = N/A, Active Off < 3 sec
VX2433wm-1
2.6 ELECTRICAL REQUIREMENT
Horizontal / Vertical Frequency
Horizontal Frequency 24 – 83 kHz
Vertical Refresh Rate 50 –76* Hz
Maximum Pixel Clock Analog : 205 MHz
Digital : 175 MHz
Sync Polarity Independent of sync polarity
Timing Table
Digital - TMDS
Analog
Composite
Separated
Item Timing Remark
SOG
1 640 x 350 @ 70 Hz, 31.5 KHz v v v v DMT
2 640 x 400 @ 60 Hz, 31.5 KHz v v v v DMT
3 640 x 400 @ 70 Hz, 31.5 KHz v v v v DMT
4 640 x 480 @ 50 Hz, 24.7 KHz v v v v CVT
5 640 x 480 @ 60 Hz, 31.5 KHz v v v v DMT
6 640 x 480 @ 67 Hz, 35 KHz v v v v For MAC
7 640 x 480 @ 72 Hz, 37.9 KHz v v v v DMT
8 640 x 480 @ 75 Hz, 37.5 KHz v v v v DMT
9 720 x 400 @ 70 Hz, 31.5 KHz v v v v DMT
10 720 x 480 @ 60 Hz, 31.5 KHz v v v v DTV
11 720 x 576 @ 50 Hz, 31.3 KHz v v v v DTV
12 800 x 600 @ 56 Hz, 35.1 KHz v v v v DMT
13 800 x 600 @ 60 Hz, 37.9 KHz v v v v DMT
14 800 x 600 @ 72 Hz, 48.1 KHz v v v v DMT
15 800 x 600 @ 75 Hz, 46.9 KHz v v v v DMT
16 832 x 624 @ 75 Hz, 49.7 KHz v v v v MAC
17 1024 x 768 @ 50 Hz, 39.6 KHz v v v v CVT
18 1024 x 768 @ 60 Hz, 48.4 KHz v v v v DMT
19 1024 x 768 @ 70 Hz, 56.5 KHz v v v v DMT
20 1024 x 768 @ 72 Hz, 58.1 KHz v v v v DMT
21 1024 x 768 @ 75 Hz, 60 KHz v v v v DMT
22 1024 x 768 @ 75 Hz, 60.2 KHz v v v v For MAC
23 1152 x 864 @ 75 Hz, 67.5 KHz v v v v DMT
VX2433wm-1
24 1152 x 870 @ 75 Hz, 68.7 KHz v v v v For MAC
25 1152 x 900 @ 67 Hz, 62.5 KHz v v v v For SUN
26 1280 x 720 @ 50 Hz, 37.5 KHz v v v v DTV
27 1280 x 720 @ 60 Hz, 45 KHz v v v v DTV
28 1280 x 768 @ 50 Hz, 39.6 KHz v v v v DMT;
29 1280 x 768 @ 60 Hz, 47.8 KHz v v v v DMT;
30 1280 x 768 @ 75 Hz, 60.3 KHz v v v v DMT;
31 1280 x 960 @ 50 Hz, 49.4 KHz v v v v DMT
32 1280 x 960 @ 60 Hz, 60.0 KHz v v v v DMT
33 1280 x 960 @ 75 Hz, 75.2 KHz v v v v DMT
34 1280 x 1024 @ 50 Hz, 52.7 KHz v v v v DMT
35 1280 x 1024 @ 60 Hz, 64 KHz v v v v DMT
36 1280 x 1024 @ 75 Hz, 80 KHz v v v v DMT
37 1360 x 768 @ 60 Hz 47.7 kHz v v v v DMT
38 1440 x 900 @ 60 Hz 55.9 KHz v v v v DMT
39 1440 x 900 @ 75 Hz 70.6 KHz v v v v DMT
40 1400 x 1050 @ 60 Hz 65.3 KHz v v v v DMT
41 1400 x 1050 @ 75 Hz 82.3 KHz v v v v DMT
42 1600 x 1200 @ 60 Hz 75.0 KHz v v v v DMT
43 1680 x 1050 @ 60 Hz 64.7 KHz v v v v DMT
44 1680 x 1050 @ 60 Hz 65.3 KHz v v v v DMT
45 1920x1080 @ 60 Hz 67.5 KHz v v v v DMT
46 480i @ 60 Hz v
47 480p @ 60 Hz v   v
48 576i @ 50 Hz v
49 576p @ 50 Hz v   v
50 720p @ 50 Hz v   v
51 720p @ 60 Hz v   v
52 1080i @ 50 Hz v
53 1080i @ 60 Hz v
54 1080p @ 50 Hz v   v
55 1080p @ 60 Hz v   v
*1. Tolerance ≧ ±2KHz. (if no over lapping issue)

*2. Any timing not in the list, it should display as normal or show on “OUT OF RANGE” OSD message without
blanking.
*3. The image quality of 85Hz mode might be worse than 75Hz.
VX2433wm-1
Primary Presets
1920x1080 @ 60Hz
User Presets
Number of User Presets (recognized timings) Available: 10 presets total in FIFO configuration
Changing Modes
ϥʳ Maximum Mode Change Blank Time for image stability : 3 seconds (Max), excluding “Auto
Adjust” time
ϥʳ It should recall factory setting when execute Auto Image Adjust function by following
conditions,
1. Memory recall under DOS mode (640 x 350, 720 x 400 & 640 x 400).
2. New timing mode detected under DOS mode (640 x 350, 720 x 400 & 640 x 400).
ϥʳ The monitor needs to do “Auto Adjust” the first time a new mode is detected
(see section “0-Touch™ Function Actions”)
ϥʳ While running Change Mode, Auto Adjust or Memory Recall, the image shall blank
VX2433wm-1
3. Front Panel Function Control Description
3.1 FRONT PANEL HARDWARE CONTROLS
Power Switch (Front Head) AC Power Switch on the back cover
Soft Power Switch on the front bezel
Power LED (Front Head) Blue – ON
Amber – Active Off
Dark = Soft Power Switch OFF
Front Panel Controls (Head) [ ] Power
[ 1 ] [ 2 ] [ ] [ź] [Ÿ] [ 1 ] BUTTON 1
[ 2 ] Button 2
[Ÿ] UP ARROW BUTTON
[ź] DOWN ARROW BUTTON
Note: Power Button, Button 1 and Button 2 must be

one-shot logic operation. (i.e. there should be no
cycling)
Reaction Time OSD must fully appear within 0.5s after pushing
Button 1
3.2 SHORT CUTS FUNCTION FROM THE BUTTON(S)

[1] Main Menu
[2] Input toggle (Analog or DVI or HDMI; refer to Appendix D)
[ź] To immediately activate Audio menu.
To immediately activate Contrast menu. It should be change to Brightness
OSD by push button [2]
(refer to the Contrast OSD in segment 4-5-3)
[Ÿ]
*1 refer to the Brightness OSD in segment 4-5-3

*2 Under sRGB or DCR mode, this function is disable
[ź] Under HDMI mode, toggle audio source between HDMI and jack plug
(Keep pushing 5 sec)
When switch to HDMI
VX2433wm-1
When switch to AUDIO IN (earphone jack)
[ź]+ [Ÿ] 1. In the CR/ BT menu, Recall Contrast or Brightness to default in its
menu without OSD message.
2. In the Audio menu, Recall both of audio volume and mute to default
* While OSD menu off, recall CR/ BT/ Audio volume and mute to default
without OSD message
[1] + [2] Toggle 720x400 and 640x400 mode when input 720x400 or 640x400 mode
* Default = 720 x 400

[1] + [ź] + [Ÿ] White Balance
(Keep pushing 5 sec) 1. It will not shown on user’s guide
2. OSD message as below,
(Image = no blanking)
3. Recommend environment
3.1. Optical (Best) input timing = 640 x 480 @ 60Hz;
Following timing modes also recommended,
800 x 600 @ 60 Hz
1024 X 768 @ 60 Hz
3.2. Pattern as below,
[1] + [Ÿ] OSD Lock

(refer to segment 4-6-4)
[1] + [ź] Power Lock
[2] + [ź] Toggle DDC/CI and DDC/2B (DDC/CI enable/disable) and show following
message for 3 seconds,
VX2433wm-1
When switch to DDC/CI
When switch to DDC/2B
Default = DDC/CI
Signal + [2] + [ ] Factory Mode
Remark : All the short cuts function are only available while OSD off
3.3 MAIN MENU OSD TABLE

Main Menu 1. Key button definition:
[1]: OSD off
[2]: Execute the selected function
[Up]: Rolling up the slider
(When push the button on the top position, the slider shall
go down to the bottom item)
[Dn]: Rolling down the slider
(When push the button on the bottom position, the slider
shall go down to the top item)
2. Under sRGB or DCR mode, the Contrast/Brightness shall be
disabled with gray color. And it should not be selected.
Level 1 Level 2 Level 3

Auto Image Adjust ʳ ʳ
1. Background = blanking
2. The message OSD position is at
the center.
3. After auto tune, OSD shall be off
4. Only for analog mode 4. Only for
analog mode
Contrast/Brightness Contrast ʳ
VX2433wm-1
Jump to Contrast OSD directly Contrast
1. Adjust range = 0 to 100

2. Default = 70
3. Key button definition:
[1] = Back to Main Menu or OSD
off (depend on previous status)
[2] = Change to Brightness OSD
[Up] = Increase the OSD value
setting
[Dn] = Decrease the OSD value
[Up]+[Dn]: Recall to default
Brightness ʳ

2. Default = 100
[1] = Back to Main Menu or OSD
off (depend on previous status)
[2]: Change to Contrast OSD
[Up]: Increase the OSD value
setting
[Dn]: Decrease the OSD value
Input Select D-SUB
Step 1: Turn off OSD.

Step 2:
1. Target video input port = Analog
2. If signal detected from target
port, change to target port.
1. Show on existing input port by red 3. If no signal detected from target
color port, keep existing input port.
VX2433wm-1
2. Key button definition: Step 3: Show on Input Message
[1]: Back to previous OSD status OSD at the right-top corner of
[2]: Change to the selected input screen for 1 second.
port
[Up]: Move up the slider
[Dn]: Move down the slider DVI

Step 2:
1. Target video input port = Digital
3. If no signal detected from target
port, keep existing input port.
Step 3: Show on Input Message
OSD at the right-top corner of
screen for 1 second.
HDMI PC

Step 2:
1. Target video input port = HDMI
PC
HDMI PC
HDMI AV

Step 2:
VX2433wm-1
1. Target video input port = HDMI
AV
HDMI AV
Audio Adjust Volume ʳ

2. Default = 50
[1]: Back to Audio Adjust OSD
1. The selected icon in Mute will be [Up]: Increase the volume setting
highlighted [Dn]: Decrease the volume setting
[1]: Back to previous OSD status Mute

[2]: Change to Volume or Mute the 1. Default = Off
selected audio setting 2. Key button definition:
[Up]: Increase the volume settingMove [1]: Back to Audio Adjust OSD
up the slider or Toggle audio to Mute [2]: Switch to Volume adjustment
or Audible icon [Up],[Dn]: Toggle audio to Mute or
[Dn]: Decrease the volume Audible iconToggle audio to Mute
settingMove down the slider or Toggle or Audible icon
audio to Mute or Audible icon 3. When Mute function is selected, any
3. No signal, no output change in Volume will disable Mute and
4. This function must memorize its toggle to Audible icon.
status after DC/AC Off to On
Color Adjust sRGB

Change Color setting to sRGB
9300K ʳ
Change Color setting to 9300K
7500K
6500K ʳ
VX2433wm-1
1. Show on existing input port by red Change Color setting to 6500K
color 5000K ʳ
2. Default = 6500K User Color Red
3. Key button definition: Jump to Red OSD directly

[1]: Back to previous OSD status
[2]: Change to the selected color
setting 1. Adjust range = 0 to 100

[Up]: Move up the slider 2. Default = 100
[Dn]: Move down the slider 3. Key button definition:
[1]: Back to Color Adjust OSD

4. Under DCR mode (Dynamic Contrast [2]: Jump to Green OSD
= On), SRGB shall be disabled with [Up]: Increase the OSD value setting
gray color. And it should not be [Dn]: decrease the OSD value setting
selected. Green
2. Default = 100

[2]: Jump to Blue OSD
[Up]: Increase the OSD value setting
[Dn]: decrease the OSD value setting
Blue
2. Default = 100
[2]: Jump to Red OSD
VX2433wm-1
[Dn]: decrease the OSD value setting
Information ʳ ʳ
PC timing – Display Resolution
Video timing – Display Video Format
Key button definition:
[1]: Back to Main Menu OSD
Manual Image Adjust H/V Position Horizontal Position
Jump to Horizontal Position OSD

directly
[1]: Back to Manual Image Adjust OSD
[2]: Change to Vertical Position OSD

1. Key button definition: [Up]: Increase the OSD value setting
[1]: Back to previous OSD status [Dn]: Decrease the OSD value
[2]: Execute the selected function Vertical Position
[Up]: scroll up the slider
(When push the button on the top
position, the slider shall go down to
the bottom item
[Dn]: Scroll down the slider 1. Adjust range = 0 to 100
VX2433wm-1
(When push the button on the 2. Key button definition:
bottom position, the slider shall go [1]: Back to Manual Image Adjust OSD
down to the top item [2]: Change to Horizontal Position OSD
2. Under Digital mode, all the H./V. [Up]: Increase the OSD value setting
Position, Horizontal Size and Fine [Dn]: Decrease the OSD value
Tune shall be disabled with gray Horizontal Size ʳ
color. And it should not be selected.
3. Under native mode, Sharpness shall
be disabled with gray color. And it
should not be selected. 1. Adjust range = 0 to 100

4. Under SRGB mode, Dynamic 2. Key button definition:
Contrast shall be disabled with gray [1]: Back to Manual Image Adjust
color. And it should not be selected. OSD
5. When move to Dynamic Contrast, [Up]: Increase the OSD value setting
the right-bottom side icon will
change to “[ 2 ]: ;/” [Dn]: Decrease the OSD value
Fine Tune
[1]: Back to Manual Image Adjust
OSD
Sharpness ʳ
(0,25,50,75,100)
2. Default = 50
OSD
VX2433wm-1
Dynamic Contrast ʳ
Swap on and off the Dynamic Contrast
function
Default = Off
When Dynamic Contrast is on, below
functions will be disabled:
1. Brightness/Contrast menu
2. SRGB selection in Color Adjust
3. White balance hot key
4. DDC/CI BR/CT adjustment
Response Time Standard
Over Drive = off
1. Show on existing Response Time
setting by red color
[2]: Change to the selected Response
Time setting.
[Up]: Scroll up the slider
position, the slider shall go down to
the bottom item)
[Dn]: Scroll down the slider
(When push the button on the
bottom position, the slider shall go
up to the top item)
3. Default = Advanced
Advanced
Over Drive = Level 1
( best quality with over drive )
Ultra Fast
Over Drive = Level 2
VX2433wm-1
( faster than level 1)
Aspect Ratio 4:3

Change aspect ratio to 4:3
Full Screen
Fill screen with panel native aspect ratio.
1. Show on existing Aspect Ratio
[2]: Change to the selected Display
Mode setting.
top position, the slider shall go
down to the bottom item)
[Dn]: Scroll down the slider (When
push the button on the bottom
position, the slider shall go up to
the top item)
3. Default = full screen
Note : 1.When input signals are
wide format, this function is
disable.
2. When input signals are non-wide
format. this function is enable.
Display Mode RGB Mode

Set color space to RGB mode for PC timing
mode
YUV Mode
1. This function toggles RGB and YUV Set color space to YUV mode for HD timing
display mode. mode
2. Show on existing Display Mode
VX2433wm-1
Mode setting.
up to the top item)
4. Save PC timing and DTV timing
setting separately.
5. Default = RGB Mode ( DVI &VGA) ,

6. HDMI is auto detected by Info Frame : ,
YPbPr -> HD mode,
Non-YPbPr -> PC mode.
7. It will recall to default after AC/DC on/off or
mode change.
ECO Mode Standard

OSD adjust range = 0 to 100
Optimize
Conserve
1. This function toggles ECO mode.
2. Show on existing ECO Mode setting
by red color
VX2433wm-1
Mode setting.
up to the top item)
4. Default = Standard
5. Under sRGB mode, ECO Mode shall
be disabled with gray color. And it
should not be selected.
6. No matter DCR on or off, lamp current

will be changed by ECO mode
change.
7. While ECO or DCR setting changed,

the lamp current shall be updated to
new setting immediately.
8. Do not lock Contrast or Brightness
OSD for ECO function

9. Following is the lamp current chart,
VX2433wm-1
Setup Menu Language Select English
Set OSD language to English and
keep in Language Select OSD
French
Set OSD language to French and
German
1. Key button definition: Set OSD language to German and
[1]: Back to Main Menu OSD 1. Show on existing input port by red keep in Language Select OSD
[2]: Execute the selected function color Spanish
[Up]: Rolling up the slider 2. Key button definition: Set OSD language to Spanish and
(When push the button on the top [1]: Back to previous OSD status keep in Language Select OSD
position, the slider shall go down [2]: Change to the selected language Italian
to the bottom item) setting Set OSD language to Italian and
[Dn]: Rolling down the slider [Up]: Scroll up the slider keep in Language Select OSD
(When push the button on the (When push the button on the top Finnish
bottom position, the slider shall position, the slider shall go down to Set OSD language to Finnish and
go down to the top item) the bottom item keep in Language Select OSD
Russian
2. When Resolution Notice / OSD (When push the button on the
Background / is selected, the Set OSD language to Russian and
right side description will bottom position, the slider shall go
change to “[ 2 ]: ;/” down to the top item
Japanese
Set OSD language to Japanese
and keep in Language Select OSD
Korean
Set OSD language to Korean and
Simplified Chinese
Set OSD language to Simplified
Chinese and keep in Language
Select OSD
Traditional Chinese
Set OSD language to Traditional
Select OSD
VX2433wm-1
Resolution Notice ʳ
Swap on and off the Resolution Notice
function
OSD Position OSD H. Position
Jump to OSD H. Position OSD directly
2. Default = 50
[1]: Back to Setup Menu OSD
[2]: Change to OSD V. Position
OSD
setting (move OSD right)
setting (move OSD left)
value
OSD V. Position
2. Default = 50
[2]: Change to OSD H. Position
OSD
setting (move OSD up)
setting (move OSD down)
value
VX2433wm-1
OSD Time Out 5
Set OSD Time Out to 5 Seconds
15
1. Adjust range = 5, 15, 30, 60 30
2. Default = 15 Set OSD Time Out to 30 Seconds
3. Key button definition: 60
[1]: Back to Setup Menu OSD Set OSD Time Out to 60 Seconds
setting
[Up]+[Dn]: Recall to default value
OSD Background ʳ
Swap on and off the OSD Background
; = Non-transparent
= Transparent
Sleep 30 Minutes
Set time before going to Sleep
mode = 30 Minutes
45 Minutes
Set time before going to Sleep
mode = 45 Minutes
1. Adjust time range before going to 60 Minutes

sleep mode. Time range = 30, 45, 60, Set time before going to Sleep
120 (Minutes) and Off. mode = 60 Minutes

2. Default = Off
3. When Sleep mode is triggered, the 120 Minutes

power of monitor will be turned off. Set time before going to Sleep
4. Only active in HD mode. Only active mode = 120 Minutes
in HDMI Mode (both in AV&PC)

Off
[2]: Change to the selected sleep
Disable Sleep mode.
time setting
VX2433wm-1
down to the bottom item
bottom position, the slider shall
go down to the top item
Memory Recall ʳ
2. Recall white balance to factory setting
3. Recall all the OSD setting to the
default. (include the R/G/B in User
Color)
4. Show the message OSD position is at
the center for 3 seconds.
5. Clean FIFO timing mode buffer
6. Execute Auto Image Adjust
Note: Memory Recall should not effect
on Language, Power Lock Settings or
Input Priority
VX2433wm-1
3.4 OSD LOCK SHORT CUTS FUNCTION FOR THE BUTTONS
The OSD lock will be activated by pressing the front panel control buttons [1] + [Ÿ] for 10
seconds *1. If the user then tries to access the OSD by pressing any of the buttons, a
message will appear on the screen for 3 seconds showing "OSD Locked" *2. The OSD
lock will be deactivated by pressing the front panel control buttons [1] + [Ÿ] again for 10
seconds*3.
*1 The OSD Lock message as below,
Range = 0 to 10
*2 The OSD Locked message as below,
*3 The OSD Unlock message as below,
Range = 0 to 10
*4 When the OSD is locked will lock all functions, including “Volume”, “Mute” and others.
*5 Status bar indicating OSD Lock or Unlock is in progress and when complete it will indicate “OSD
Locked” or “OSD Unlocked” for 3 seconds as below,
OSD Locked
OSD Unlocked
*6 When OSD appears on screen, the OSD Lock/Unlock short cut key will be disabled.
VX2433wm-1
3.5 POWER LOCK SHORT CUTS FUNCTION FOR THE BUTTONS
The Power lock will be activated by pressing the front panel control buttons [1] + [ź] for 10
seconds *1. Locking the power button means that the user won't be able to turn off the LCD while
the power button is locked. If the user presses the power button while it is locked, a message will
appear on the screen for 3 seconds showing "Power Button Locked" *2. It also means that with
the power button locked, the LCD would automatically turn back "On" when power is restored
after a power failure. If the power button is not in the locked mode, then power should return to
it's previous state when power is restored after a power failure. The Power lock will be
deactivated by pressing the front panel control buttons [1] + [ź] again for 10 seconds*3.
*1 The Locking Power Button message as below,
Range = 0 to 10
*2 The Power Button Locked message as below,
*3 The Unlocking Power Button message as below,
Range = 0 to 10
*5 Status bar indicating Power Button Lock or Unlock is in progress and when complete it will
indicate “Power Button Locked” or “Button Unlocked” for 3 seconds as below,
Power Button Locked
Power Button Unlocked
*6 When OSD appears on screen, the OSD Lock/Unlock short cut key will be disabled
VX2433wm-1
3.6 RESOLUTION NOTICE ACTIONS
1. Resolution Notice OSD should show on screen after changing to non-native mode for 30 sec

[1]: Turn off the OSD message.
[2]: Turn off the OSD message and disable Resolution Notice function
3. The OSD should disappear after 10 sec or by pushing button [1] or [2]
4. After the OSD turns off, it will not show on again before next timing change, input change or power off.
5. Resolution Notice function should be disabled when push button [2] under Resolution Notice OSD
6. The “1366x768” will be replaced by actual panel resolution.
3.7 TOUCH™ FUNCTION ACTIONS

1. Execute Auto Image Adjust when new mode detected, and save the settings to buffer for
further use
2. It should be reset by Memory Recall function
(Should not reset by power off, power unplug and others)
3.8 OSD AUTO SAVE

The OSD shall save new settings when it is turned off by the user or when it times out. There shall not be a
separate save
3.9 OUT OF RANGE

While non-defined timing is detected, following OSD message will keeps showing on,
1. If the timing is over spec (Fh, Fv or dot clock), the image shall be blanking, and OSD background shall be
non-transparent.
2. If the timing is inspect but not defined, the image shall be non-blanking.
VX2433wm-1
3.10 NO SIGNAL FOR D-SUB / DVI
While no signal is detected for D-Sub and DVI, the following OSD message shall shows on 3 seconds then go in to
power saving.
OSD Background = Non-transparent

Image = Blanking
3.11 ACTORY DEFAULTS
Item Defaults Item Defaults

Contrast 70% OSD Time Out 15 Sec
Brightness 100% OSD Background On
Color Temperature 6500K Volume 80%
Sharpness 100% Treble N/A
OSD H. Position 50% Bass N/A
OSD V. Position 50% Input Priority Auto Search
720x400/640x400 720x400 Resolution Notice Enabled
VX2433wm-1
Packing For Shipping And Disassembly Procedure
Packing For Shipping

1. Packing Procedure
Paste protection film to protect the monitor. (Figure 1)
Put the monitor in the PE bag and seal the bag with tape. (Figure 2)
Figure 1 Figure 2
Put the cushions on the monitor.
Place the monitor into the carton and then put all the accessories into the carton. At last, close the carton
and seal it with tape. (Figure 3)
Moniter Head
VGA cable
Power cord
Base
Figure 3
VX2433wm-1
Disassembly Procedure
BASE
STAND
VX2433wm-1
BACKCOVER
VX2433wm-1
PANEL
BEZEL
VX2433wm-1
KEYPAD
CHASIS
VX2433wm-1
POWER BOARD
LVD CABLE
SHORT KEYPAD-CABLE
VX2433wm-1
IF BOARD
VX2433wm-1
4. Circuit Description
4.1 Switching Mode Power Supply
4.3.1 AC Current Input Circuit
P801 is a connector for connecting AC Power. F801 is a fuse to protect all the circuit. AC input
voltage is from 90v to 264V. R801,R831 and R802 joined between two inputting main circuit to
prevent man from shock. L801 is used to clear up low frequency wave. C801 and C802 are used to
discharge the waves that L801 produced. High frequency waves are damped by C801 and C802.
D801 is a rectifier which composed of 4 build-in diodes, it inverts AC to DC.
4.3.2 High Voltage to Low Voltage Control Circuit

C804 is used to smooth the wave from rectifier. IC802 is a highly integrated PWM controller.
When rectified DC high voltage is applied to the HV pin during start-up, the MOSFET Q804 is initially
off, and the Vcc pin capacitor is charged. When the Vcc pin voltage reaches approximately 10V, the
control circuitry is activated and the soft-start begins. The soft-start circuit gradually increases the duty
cycle of the MOSFET from zero to the maximum value over approximately 4ms. a stably output
voltage Will be increase about 40ms later, and then feedback a continue current through the IC801
which control the output of the PWM IC. If no external feedback/supply current is feed into the FB
pin by the end of the soft-start, the current Set point will be above the fault level, FAULT flag is raised,
if the FAULT duration exceeds 80ms, the output controller disable
Resistor R808, R809, R810, R811 are for line over voltage shutdown(OVP) and Brown Out
Protection (BOP)
When PWM is turned off, the main current flow will be consumed through R804 and D802, This
will prevent MOSFET Q804 from being damaged under large current impulse and voltage spike.
D803 and C807 to provide internal Auxiliary voltage to Vcc pin during normal operation.
Otherwise, error amplifier and feedback current input the FB pin for duty cycle control.
4.3.3 DC_5V and DC_14V Output Circuit

For DC 5V, D805 is used to rectify the inducted current. R828 and C814 are used to store
energy when current is reversed. The parts including C818, C822, C820,L803 are used to smooth
the current waves.
For DC 14V, D803 is used to rectify the inducted current. R827 and C813 are used to store
energy when current is reversed. The parts including C815, C817 and L802 are used to smooth the
current waves.
4.3.4 Feedback and OVP Protect Circuit

Pin R of IC803 is supplied 2.5-v stable voltage. It connects to 5V and 14V output through
R822, R823 and R824. R822, R823 and R824 are output sampling resistor. When the sampling
voltage more than 2.5V or less than 2.5V, current of FB IC802 will change, this can change the
voltage from T801.
VX2433wm-1
4.2 Inverter Circuit
1. R503, ZD501, R502, Q501 components convert +14V voltage into +5.0V voltage, and the voltage
supply to IC501. The extra PWM pulse signal (BRIGHTNESS signal) input to control IC through R512,
R514, C510, The LCT pin is set to a DC voltage of 0.7V by using a resistor divider(R507, R516), change
the duty of PWM pulse, will regulate the lamp current. The ON/OFF voltage connect to pin10 of IC501
through D501, R501, A voltage of 2V to pin10 of IC501 enables the IC and activates the striking timer.
The SSTCMP pin of IC501 performs the soft function, the C511 set the time of SST. The operation
frequency determined by external capacitor C512, C521 and resistor R508 connected at CT pin of IC501.
C515 connect the TIMER pin of IC501, the capacitor to set striking time and shunt down delay time.
DRV!, DRV2 output for power MOSFET U501, U502.
2. OZ9938 provides two drive signals for U501, U502, and they work in push pull topology driving, two
transformers are connected in parallel with each transformer driving two lamps in series. Turning each
N-Channel MOSFET “on/off” complementarily, produces an alternating current through the transformer
primary and secondary. The “on” duration of the switches determines the amount of energy delivered to
the CCFLs. R504, C504, R505, C505, R532, C529, R530, C522 are snubber networks, they suppress
Voltage transient spike in drain of power MOSFET.
3. R506, R510, C509, C513, C514, R525, R531, C528, C525, and C527 are connected between high
voltage output connector and ground, the divided AC voltage is inverted DC voltage through D502, D503,
D508, and D509. The sense voltage feed back to VSEN (pin 6 of IC501) for an over voltage/over current
condition during normal operation. R528, R533 are current sense resistor, current sense signal feed back
to Isense (pin 5 of IC501) for lamp “ON” detection.
4.3 I/F Board Circuit
4.3.1 Power Input
+5V is from the power board and supply for U101(FSP2160-3.3V)ΡU105(NT68672UMFG) and panel.
+3.3V output is generated from +5V through C102 filtering, and U101 outputs. +3.3V is used for U108 U105
(NT68672UMFG). +1.2V output is generated from +3.3V through U102 outputs. +1.2V is only used for Scaler
NT68672..
4.3.2 Scaler(NT68672UMFG)
1.) NT68672: The NT68673UMFG is a highly integrated flat panel display controller that
interfaces analog and digital inputs. It combines a triple ADC, a HDMI 1.3 receiver, a high
quality zoom and shrink engine, a multi-color on screen display (OSD) controller and many other
functions in a single chip. It provides the user with a simple, flexible and cost-effective solution
for various flat panel display products.
The NT68673UMFG operates at frequencies up to 205MHz, suitable for LCD monitor up to
WUXGA resolution. The NT68673UMFG also has a built-in 2D noise reduction function to
provide more stable video quality, spread spectrum to provide low EMI solution, sRGB for video
color space convert and post pattern for manufacture test.
The display provided single/double pixel clock LVDS interface.
VX2433wm-1
In addition, NT68673UMFG includes an integrated 8-Bit Microcontroller (MCU). It contains an
8-bit 8031 micro-controller, 5,120-bytes internal data memory, eight 7-bit resolution A/D
Converter, 10- channel 8-bit resolution PWM DAC, two16-bit timer/counters, and a UART.
Except those, it has two channel hardware DDC solution, and VESA 2Bi/2B+ master/slave I2C
bus interface. It can support up to External 512 K Bytes SPI Flash memories for program
memory.
2.) EEPROM: We use 24C16 EEPROM to store DDC (Display Data Channel) data. The end-users’
setting data is stored in the 24C16 EEPROM. Each timing mode is allocated with 16 bytes of
memory space for information such as Sync frequencies, polarities… etc. PC can access the
EEPROM data indirectly through the D-sub-SDA and D-sub-SCL channels. (IͅC communication)
4.3.3 VGA Input

Signal R, G, B input through CN102 #1, #2, #3. Signal HSYNC and VSYNC input through CN102 #13 and
#14, and C129, R135, C130, R136 filtering. Then the analog signal enters U105, and then U105 deals with it
internally. In addition, D104, D105, D102,D103 (the four are BAV99), ZD102, ZD103, ZD104, ZD105, ZD106
(they are constant voltage diode of 6V2) are ESD protector. Signal DDC-SCL inputs via CN102 #15, and then
passes through ZD106 for ESD protection, goes into U105 #41. Signal DDC-SDA inputs via CN102 #12, and
then passes through ZD105 for ESD protection, goes into U105 #42. CN102 #5 is defined as cable detect pin,
this detector realizes via R125,The PC-5V of U105 is supplied by PC via CN102 #9 with D101.
4.3.4 Button Control

Button “Key-Power” is defined as power on/off, which is connected to U105 # 74 through CN104 #8.
Button “Key-2” is defined as two functions of selecting and adjustment, which is connected to
U105#113through CN104 #2.
Button “Key-Up” is defined as plus, which is connected to U105 # 112 through CN104
#4
Button “Key-Down” is defined as minus, which is connected to U105 # 111 through CN104 # 3.
Button “Key-1” is defined as two functions of menu and exit, which is connected to U105 # 47 through
CN104 # 1.
LED indicator on the front bezel is defined as follows:
a. When press button “Key-Power”, U105 # 74 is pulled high and U105 # 103 is pulled low, so Q107 is
conducted and the LED indicator is blue.
b. When in power-saving mode, U105 # 108 is pulled high and U102 # 1 is pulled down, so Q108 is conducted
and the LED indicator is orange.
VX2433wm-1
4.4 Power On/Off Sequence
4.4.1 Hardware Power ON
When power cord is plugged into AC socket, SMPS starts work and provides U105 with VCC5V. When
VCC5V inputs, U105 resets circuit active, sets U105 all registers to preset modes, and then monitor goes into
stand-by mode. That means hardware power on has been completed.
4.4.2 Software Power ON/OFF

When press power key, U105 # 74 recieves low pulse,and then U105 will do the power on/off.
- If Power ON, U108 # 103(LED_Blue) will send out Low potential, and then LED Blue on.
- If Power OFF, U108 # 103(LED_ Blue) will send out High potential, and then LED Off.
The Panel_Vcc, Backlight_En, CLK/DATA output to panel will follow the following sequency.
T1 (ms) T2 (ms) T3 (ms) T4 (ms) T5 (ms) T6+T7 (ms)

0.5~10 0~50 500 90 0~50 500
4.4.3 AC Outlet Pin Assignment
Pin Symbol Description

3
1 L Live
1 2
2 N Neutral
P801 3 E GND
VX2433wm-1
4.5 Inner Connector Pin Assignment
4.5.1 CN501, CN502, CN503, CN504 (Connect to Panel Backlight, SM02B-BHSS-1-TB or equivalent)
Pin Symbol Description
1 H.V. High voltage for lamp
2 L.V. Low voltage for lamp
4.5.2 CN101 (Power BD to Interface BD)

Pin No. Symbol Description
1 VCC5V +5V INPUT
2 VCC5V +5V INPUT
3 GND GND
4 GND GND
5 GND GND
6 GND GND
7 Backlight_ON/OFF CCFL on/off control
8 Adjust_Brightness Panel luminance control (CCFL brightness)
4.5.3 CN104 (Interface BD to Keypad)

Pin
Symbol Description
No.
1 KEY_Menu OSD menu and exit
2 KEY_2 Auto adjustment control and selecting.
3 KEY_Minu OSD “ź” control to adjust value to decrease
4 KEY_Plus OSD “Ÿ” control to adjust value to increase
5 LED_B Blue LED lighting control
6 GND GND
7 LED_O Orange LED lighting control
8 KEY_POWER DC power on/off control
4.5.4 CN103 (Connect I/F BD to panel, FI-X30S-H or Equivalent)

Pin No. Symbol Function
30 RXO0- Negative LVDS differential data input.Channel O0(odd)
29 RXO0+ Positive LVDS differential data input.Channel O0(odd)
VX2433wm-1
24 GND Ground
23 RXOC- Negative LVDS differential clock input (odd)
22 RXOC+ Positive LVDS differential clock input (odd)
19 RXE0- Negative LVDS differential data input.Channel E0(even)
18 RXE0+ Positive LVDS differential data input.Channel E0(even)
17 GND Ground
14 GND Ground
11 RXEC- Negative LVDS differential clock input (even)
10 RXEC+ Positive LVDS differential clock input (even)
7 GND Ground
6 NC Not connection
5 NC Not connection.
4 NC Not connection
3 VCC Power supply (5.0 V)
4.5.5 CN102 (D-SUB Connector)

Symbol Pin Symbol Pin Symbol
1 Red video input 6 Red GND 11 GND
2 Green video input 7 Green GND 12 Serial data line (SDA)
3 Blue video input 8 Blue GND 13 Hsync
4 GND 9 +5V(from PC) 14 Vsync
5 Cable Detect 10 Not Connected 15 Serial clock line (SCL)
VX2433wm-1
4.6 Key Parts Pin Assignment
4.6.1 IC802 (TOP245Y or TOP246Y, Power Control IC)

Pin Symbol I/O Description
1 BO I Brown-out and external triggering
2 FB I Sets the peak current setpoint
3 CS I Current sense input and overpower compensation adjustment
4 GND IC ground
5 DRV O Output driver
6 VCC I IC supply
7 NC
8 HV I High-Voltage pin
4.6.2 IC501 (OZ9938GN, CCFL inverter controller IC)

Pin No. Symbol I/O Description
Open lamp voltage feedback input 2. Connect a capacitive voltage
divider from the hot terminal of the lamp to ground. Connect this pin to
the tap on the divider and a bias resistor to VCC. In multi-lamp
application, connect a diode from each lamp capacitive voltage divider
which is in-phase to each other to this pin. If the peak voltage value at
OV2 pin exceeds +13V, the controller will treat this as lamp overvoltage
1 OV2 I condition. A pulse of current will pull-down on the COMP pin to regulate
the lamp voltage. The burst dimming signal will be ignored and the Fault
Timer will start ramping up. This signal is also used for short circuit
protection. If the voltage at OV2 is always above 4.9V, the controller will
treat this as a short circuit condition after a certain delay. The Fault Timer
will start ramping up. In single lamp application, connect this pin to OV1
pin.
Lamp current feedback 1. Connect this pin to the current sense resistor.
In multi-lamp application, connect a diode from this pin to each lamp
current sense resistor which is in-phase to each other. These diodes
forms an AND gate with an internal 60uA pull up current source.
Combined with the lamp current feedback signal from LI2, the signal is
2 LI1 I
fed to the internal error amplifier. Selecting the feedback resistors can
easily program the lamp current. The signal is also used for open lamp
protection. If the voltage at LI1 is always below 1.15V, the controller will
treat this as an open lamp condition after a certain delay. The burst
dimming signal will be ignored and the Fault Timer will start ramping up.
VX2433wm-1
In single lamp application, connect this pin to LI2 pin.
Lamp current feedback 2. The function of this pin is same as LI1. In
3 LI2 I single lamp application, connect this pin to LI1. In multi-lamp application,
this pin is used for lamp current feedback which is out-of-phase of LI1.
Feedback Compensation Node. Connect a compensation capacitor from
this pin to GND. This pin is also used for IC enable control. A logic low
4 COMP I
(below 0.5V) input turns off the IC. The enable logic input signal should
have open collector (OC) structure.
Fault Indicator. Connect a capacitor from this pin to GND to program the
5 FT I open lamp and short lamp protection delay time. When the voltage on
this pin reaches 1.2V, the IC will shutdown until it is enabled again.
Switching Frequency Set. Connect a resistor from this pin to GND. This
6 FSET I
resistor sets the operating frequency of the MP1009.
Burst Repetition Rate Setting. Connect a resistor and a capacitor from
this pin to GND. If the burst dimming is to be controlled by an external

7 BOSC I
logic signal, connect BOSC to VCC and apply the logic signal to the
DBRT pin.
Burst-Mode (Digital) Brightness Control Input. The voltage range of 0V to
1.2V at DBRT linearly sets the burst-mode duty cycle from minimum to
8 DBRT I 100%. The minimum burst dimming duty can be programmed by BOSC
resistor and capacitor. If burst dimming is not used, connect DBRT to
VCC.
Input Power Rail. Decouple this pin to GND with >1μF ceramic capacitor.
9 VIN I
It is desirable to add a 10 resistor between VIN pin and the input bus.
Output Bootstrap. BT provides gate driver bias for the high-side

10 BT O
MOSFET. Connect a capacitor from BT to SW.
High-Side MOSFET Gate Output. Connect TG to the gate of the

11 TG O
high-side, external power MOSFET.
Bridge Output. Connect SW to the source of the high-side MOSFET and

12 SW O
the drain of the low-side MOSFET.
Voltage Rail Output. VCC provides power supply for the low-side gate
13 VCC O driver and the internal control circuitry. Bypass VCC to GND with a
ceramic capacitor.
Low-Side MOSFET Gate Output. Connect BG to the gate of the low-side

14 BG O
MOSFET.
15 GND IC ground
Open lamp voltage feedback input. The function of this pin is same as
16 OV1 I
OV2
VX2433wm-1
5. Adjustment Procedure
5.1 Key Function Description

Power Switch AC Power Switch on the back cover
Soft Power Switch on the front bezel
Power LED (Front Head) Blue – ON
Amber – Active Off
Dark = Soft Power Switch OFF
Front Panel Controls (Head) [ ] Power
[ 1 ] [ 2 ] [ ] [Ÿ] [ź] [ 1 ] Button 1
[ 2 ] Button 2
[Ÿ] Up arrow button
[ź] Down arrow button
Note: Power Button, Button 1 and Button 2 must be

one-shot logic operation. (i.e. there should be no
cycling)
Reaction Time OSD must fully appear within 0.5s after pushing
Button 1
5.2 Hot Key Operation

[1] Main Menu
[2] Input toggle (Analog or DVI or HDMI; refer to Appendix D)
[ź] To immediately activate Audio menu.
[Ÿ] To immediately activate Contrast menu. It should be change
to Brightness OSD by push button [2]
(refer to the Contrast OSD in segment 4-5-3)
*1 refer to the Brightness OSD in segment 4-5-3

*2 Under sRGB or DCR mode, this function is disable.
ˮϰ] Under HDMI mode, toggle audio source between HDMI and
(Keep pushing 5 sec) jack plug
VX2433wm-1
When switch to HDMI
When switch to AUDIO IN (earphone jack)
[ź]+ [Ÿ] 1. In the CR/ BT menu, Recall Contrast or Brightness to

default in its menu without OSD message.
2. In the Audio menu, Recall both of audio volume and
mute to default without OSD message.
* While OSD menu off, recall CR/ BT/ Audio volume and
mute to default without OSD message.
[1] + [2] Toggle 720x400 and 640x400 mode when input 720x400 or
640x400 mode
* Default = 720 x 400

[1] + [ź] + [Ÿ] White Balance
(Keep pushing 5 sec)
1. It will not shown on user’s guide
2. OSD message as below,
(Image = no blanking)
3. Recommend environment
3.1. Optical (Best) input timing = 640 x 480 @ 60Hz;
Following timing modes also recommended,
800 x 600 @ 60 Hz
1024 X 768 @ 60 Hz
3.2. Pattern as below,
VX2433wm-1
[1] + [Ÿ] OSD Lock / Unlock (refer to segment 4-6-4)
[1] + [ź] Power Lock / Unlock (refer to segment 4-6-5)
[2] + [ź] Toggle DDC/CI and DDC/2B (DDC/CI enable/disable) and
show following message for 3 seconds,
When switch to DDC/CI
When switch to DDC/2B
Default = DDC/CI
Signal + [2] + [ ] Factory Mode
Remark : All the short cuts function are only available while OSD off
5.3 OSD Control

5.3.1 OSD table
The OSD lock will be activated by pressing the front panel control buttons [1] + [Ÿ] for 10
seconds *1. If the user then tries to access the OSD by pressing any of the buttons, a
message will appear on the screen for 3 seconds showing "OSD Locked" *2. The OSD
lock will be deactivated by pressing the front panel control buttons [1] + [Ÿ] again for 10
seconds*3.
*1 The OSD Lock message as below,
Range = 0 to 10
*2 The OSD Locked message as below,
VX2433wm-1
*3 The OSD Unlock message as below,
Range = 0 to 10
*5 Status bar indicating OSD Lock or Unlock is in progress and when complete it will indicate “OSD
Locked” or “OSD Unlocked” for 3 seconds as below,
OSD Locked
OSD Unlocked
5.3.2 Power lock Menu function

The Power lock will be activated by pressing the front panel control buttons [1] + [ź] for 10
seconds *1. Locking the power button means that the user won't be able to turn off the
LCD while the power button is locked. If the user presses the power button while it is
locked, a message will appear on the screen for 3 seconds showing "Power Button
Locked" *2. It also means that with the power button locked, the LCD would
automatically turn back "On" when power is restored after a power failure. If the power
button is not in the locked mode, then power should return to it's previous state when
power is restored after a power failure. The Power lock will be deactivated by pressing
the front panel control buttons [1] + [ź] again for 10 seconds*3.
*1 The Locking Power Button message as below,
Range = 0 to 10
*2 The Power Button Locked message as below,
VX2433wm-1
*3 The Unlocking Power Button message as below,
Range = 0 to 10
*5 Status bar indicating Power Button Lock or Unlock is in progress and when complete it will
indicate “Power Button Locked” or “Button Unlocked” for 3 seconds as below,
Power Button Locked
Button Unlocked
5.4 Factory Defaults
Item Defaults Item Defaults

Contrast 70% OSD Time Out 15 Sec
Brightness 100% OSD Background On
Color Temperature 6500K Volume 80%
Sharpness 100% Treble N/A
OSD H. Position 50% Bass N/A
OSD V. Position 50% Input Priority Auto Search
720x400/640x400 720x400 Resolution Notice Enabled
VX2433wm-1
5.5 Function description:
!
Input Signal Notice Actions
1. The Input Signal Notice OSD appears 1 second when power turns on or change
input signal.
2. The Input Signal Notice OSD position is on the right-top side of image.
3. The OSD message as below,
Resolution Notice Actions

7. Resolution Notice OSD should show on screen after changing to non-native mode
for 30 sec.

[1]: Turn off the OSD message.
[2]: Turn off the OSD message and disable Resolution Notice function
9. The OSD should disappear after 10 sec or by pushing button [1] or [2]
10. After the OSD turns off, it will not show on again before next timing change, input change or power
off.
11. Resolution Notice function should be disabled when push button [2] under Resolution Notice OSD
12. The “1366x768” will be replaced by actual panel resolution.
0-Touch™ Function Actions

1. Execute Auto Image Adjust when new mode detected, and save the settings to
buffer for further use
2. It should be reset by Memory Recall function
(Should not reset by power off, power unplug and others)
VX2433wm-1
OSD Auto Save
The OSD shall save new settings when it is turned off by the user or when it times out.
There shall not be a separate save
Out of range
While non-defined timing is detected, following OSD message will keeps showing on,
1. If the timing is over spec (Fh, Fv or dot clock), the image shall be blanking, and OSD background shall
be non-transparent.
2. If the timing is inspect but not defined, the image shall be non-blanking.
No signal for D-sub / DVI

While no signal is detected for D-Sub and DVI, the following OSD message shall shows on 3 seconds
then go in to power saving.

Image = Blanking
No signal for HDMI
While no HDMI signal is detected, the entire screen background will display blue image, as shown below:
R=24, G=78, B=232 (R=0x18, G=0x4E, B=0xE8)
The background color will persist without power saving until HDMI input is re-connected or other input
has been selected.
The following OSD message will display for 3 seconds and then disappear.

Image = Blanking
VX2433wm-1
5.6 OSD Structure
Main Menu
[1]: OSD off
[2]: Execute the selected function
[Up]: Under Landscape mode: Scroll up the slider

(When push the button on the top position, the slider shall go down
to the bottom item)
Under Landscape mode: Scroll down the slider

(When push the button on the bottom position, the slider shall go
back to the top item)
[Dn]: Under Landscape mode: Scroll down the slider

(When push the button on the bottom position, the slider shall go
back to the top item)
Under Landscape mode: Scroll up the slider

(When push the button on the top position, the slider shall go down
to the bottom item)
2. Under sRGB or DCR mode, the Contrast/Brightness shall be disabled

with gray color. And it should not be selected.
Level 1 Level 2 Level 3
Auto Image Adjust ʳ ʳ
2. The message OSD position is at the
center.
3. After auto tune, OSD shall be off
4. Only for analog mode
Contrast/Brightness Contrast ʳ
Jump to Contrast OSD directly
2. Default = 70
VX2433wm-1
[1] = Back to Main Menu or OSD off
(depend on previous status)
[2] = Change to Brightness OSD
[Up] = Increase the OSD value setting
[Dn] = Decrease the OSD value
Brightness ʳ
2. Default = 100
[1] = Back to Main Menu or OSD off
(depend on previous status)
[2]: Change to Contrast OSD
Input Select D-SUB
Step 2:
1. Target video input port = Analog
2. If signal detected from target port, change to
target port.
3. If no signal detected from target port, keep
1. Show on existing input port by red existing input port.
color Step 3: Show on Input Message OSD at the
2. Key button definition: right-top corner of screen for 1 second.
[2]: Change to the selected input port
VX2433wm-1
[Up]: Move up the slider DVI
[Dn]: Move down the slider
Step 2:
1. Target video input port = Digital
target port.
existing input port.
Step 3: Show on Input Message OSD at the
right-top corner of screen for 1 second.
HDMI PC

Step 2:
1. Target video input port = HDMI PC
target port.
HDMI PC
HDMI AV
Step 2:
1. Target video input port = HDMI AV
target port.
4. When HDMI input and color space is YUV, it
will first detect HDMI AV
VX2433wm-1
HDMI AV
Audio Adjust Volume

2. Default =50
[1]: Back to Audio Adjust OSD

1. The selected icon in Mute will be [Up]: Increase the volume setting
highlighted [Dn]: Decrease the volume setting
2. Key button definition: Mute
[1]: Back to previous OSD status 1. Default = Off
[2]: Change to Volume or Mute the 2. Key button definition:
selected audio setting [1]: Back to Audio Adjust OSD
[Up]: Increase the volume [2]: Switch to Volume adjustment
settingMove up the slider or Toggle [Up],[Dn]: Toggle audio to Mute or Audible
audio to Mute or Audible icon iconToggle audio to Mute or Audible icon
[Dn]: Decrease the volume 3. When Mute function is selected, any change
settingMove down the slider or Toggle in Volume will disable Mute and toggle to
audio to Mute or Audible icon Audible icon.

3. No signal, no output
4. This function must memorize its
status after DC/AC Off to On
Color Adjust sRGB ʳ

Change Color setting to sRGB
9300K ʳ
7500K ʳ
6500K ʳ
1. Show on existing input port by red 5000K ʳ
color Change Color setting to 5000K
User Color Red

2. Default = 6500K
Jump to Red OSD directly

VX2433wm-1
[2]: Change to the selected color
setting 1. Adjust range = 0 to 100

[Up]: Move up the slider 2. Default = 100
[Dn]: Move down the slider 3. Key button definition:

4. Under DCR mode (Dynamic [2]: Jump to Green OSD
Contrast = On), SRGB shall be [Up]: Increase the OSD value setting
disabled with gray color. And it [Dn]: decrease the OSD value
should not be selected. setting
Green
2. Default = 100
[2]: Jump to Blue OSD
[Dn]: decrease the OSD value
setting
Blue
2. Default = 100
[2]: Jump to Red OSD
[Dn]: decrease the OSD value
setting
VX2433wm-1
Information ʳ ʳ
PC timing – Display Resolution
Video timing – Display Video Format
Key button definition:
[1]: Back to Main Menu OSD
Manual Image Adjust H/V Position Horizontal Position
Jump to Horizontal Position OSD directly
OSD
1. Key button definition: [2]: Change to Vertical Position
[1]: Back to previous OSD status OSD
[2]: Execute the selected function [Up]: Increase the OSD value
[Up]: scroll up the slider setting
(When push the button on the top [Dn]: Decrease the OSD value
position, the slider shall go down
to the bottom item
VX2433wm-1
[Dn]: Scroll down the slider Vertical Position
bottom position, the slider shall
go down to the top item
2. Under Digital mode, all the H./V.
Position, Horizontal Size and Fine 1. Adjust range = 0 to 100

Tune shall be disabled with gray 2. Key button definition:
color. And it should not be [1]: Back to Manual Image Adjust
selected. OSD
3. Under native mode, Sharpness [2]: Change to Horizontal Position
shall be disabled with gray color. OSD
And it should not be selected. [Up]: Increase the OSD value
4. Under SRGB mode, Dynamic setting
Contrast shall be disabled with [Dn]: Decrease the OSD value
gray color. And it should not be Horizontal Size ʳ
selected.
5. When move to Dynamic

Contrast, the right-bottom
side icon will change to “[ 2 ]:
;/” 1. Adjust range = 0 to 100
Fine Tune
Sharpness ʳ
VX2433wm-1
1. Adjust range ={0,25,50,75,100}
2. Default = 50
Dynamic Contrast
Swap on and off the Dynamic Contrast function
Default = Off
When Dynamic Contrast is on, below functions
will be disabled:
5. Brightness/Contrast menu
6. SRGB selection in Color Adjust
7. White balance hot key
8. DDC/CI BR/CT adjustment
Response Time Standard
Over Drive = off
1. Show on existing Response Time setting by
red color
2. Key button definition: Advanced

[2]: Change to the selected Response Time Over Drive = Level 1
setting. ( best quality with over drive )
[Up]: Scroll up the slider Ultra Fast

(When push the button on the top position,
the slider shall go down to the bottom Over Drive = Level 2

item) ( faster than level 1)
(When push the button on the bottom
position, the slider shall go up to the top
item)
3. Default = Advanced
VX2433wm-1
Aspect Ratio 4:3
Change aspect ratio to 4:3ʳ
3. Show on existing Aspect Ratio setting by red
color
2. Key button definition: Full Screen

[1]: Back to previous OSD status Fill screen with panel native aspect
[2]: Change to the selected Display Mode ratio.
setting. ʳ
position, the slider shall go down to the
bottom item)
[Dn]: Scroll down the slider (When push the
button on the bottom position, the slider
shall go up to the top item)
3. Default = full screen
Note : 1.When input signals are wide
format, this function is disable.
2.When input signals are non-wide format.
this function is enable.
Display Mode RGB Mode

Set color space to RGB for PC timing
mode
1. This function toggles RGB and YUV
VX2433wm-1
display mode. YUV Mode
2. Show on existing Display Mode setting by red Set color space to YUV for HD timing
color mode
[2]: Change to the selected Display Mode
setting.
bottom item)
item)
4. Save PC timing and DTV timing setting
separately.
5. Default = RGB Mode(VGA&DVI)

HDMI is auto detected by Info Frame :
YPbPr -> YUV mode,
Non-YPbPr -> RGB mode.
7. It will recall to default after AC/DC on/off or mode
change.
VX2433wm-1
ECO Mode Standard
1. This function toggles ECO mode.
2. Show on existing ECO Mode setting by red
color
[2]: Change to the selected Display Mode
setting.
bottom item)
item)
4. Default = Standard
5. No matter DCR on or off, lamp current will be

changed by ECO mode change.
6. While ECO or DCR setting changed, the lamp

current shall be updated to new setting
Optimize
immediately.
7. Following is the lamp current chart, conserve
8. Under SRGB mode, ECO Mode shall be
disabled with gray color. And it should not be

selected.
VX2433wm-1
9.under ECO mode, SRGB could be select and
save the contrast and brightness of ECO
10.when adjust brightness and contrast value in
current ECO mode , then change ECO mode
and return current ECO mode ,the brightness
and contrast value will be save
Setup Menu Language Select English

Set OSD language to English and
French
Set OSD language to French and
German
1. Key button definition: Set OSD language to German and
[1]: Back to Main Menu OSD keep in Language Select OSD
[2]: Execute the selected function 1. Show on existing input port by red color Spanish
[Up]: Scroll up the slider 2. Key button definition: Set OSD language to Spanish and
(When push the button on the [1]: Back to previous OSD status keep in Language Select OSD
top position, the slider shall go [2]: Change to the selected language setting Italian
down to the bottom item) [Up]: Scroll up the slider Set OSD language to Italian and keep
[Dn]: Scroll down the slider (When push the button on the top position, in Language Select OSD
(When push the button on the the slider shall go down to the bottom Finnish
bottom position, the slider shall item Set OSD language to Finnish and
go down to the top item) keep in Language Select OSD
VX2433wm-1
[Dn]: Scroll down the slider Russian
2. When move to Resolution (When push the button on the bottom Set OSD language to Russian and
Notice / OSD Background / position, the slider shall go down to the top keep in Language Select OSD
OSD Pivot, the right-bottom item
side icon will change to “[ 2 ]:

Japanese
;/”
Set OSD language to Japanese and
Korean
Set OSD language to Korean and
Traditional Chinese
Set OSD language to Simplified
Select OSD
Simplified Chinese
Set OSD language to Traditional
Select OSD
Resolution Notice ʳ
Swap on and off the Resolution Notice function
OSD Position OSD H. Position
Jump to OSD H. Position OSD directly
2. Default = 50
[2]: Change to OSD V. Position
OSD
setting (move OSD right)
setting (move OSD left)
VX2433wm-1
OSD V. Position
2. Default = 50
[2]: Change to OSD H. Position
OSD
setting (move OSD up)
setting (move OSD down)
OSD Time Out 5

15
30
1. Adjust range = 5, 15, 30, 60 Set OSD Time Out to 30 Seconds
60
2. Default = 15 Set OSD Time Out to 60 Seconds
[Dn]: Decrease the OSD value setting
OSD Background
Swap on and off the OSD Background
; = Non-transparent
= Transparent
VX2433wm-1
Sleep 30 Minutes
Set time before going to Sleep mode
= 30 Minutes
45 Minutes
Set time before going to Sleep mode
= 45 Minutes
60 Minutes
6. Adjust time range before going to sleep Set time before going to Sleep mode
mode. Time range = 30, 45, 60, 120 = 60 Minutes
(Minutes) and Off. 120 Minutes
7. Default = Off Set time before going to Sleep mode
8. When Sleep mode is triggered, the power of = 120 Minutes
monitor will be turned off. Off

9. Only active in HDMI Mode (both in AV&PC) Disable Sleep mode.
10.when selected item of SleepΔmake monitor
AC/DC OFF/ON,it will reset to off
11.Key button definition:
[2]: Change to the selected sleep time setting
bottom item

top item
Memory Recall ʳ ʳ
2. Recall white balance to factory
setting
3. Recall all the OSD setting to the
default. (include the R/G/B in User
Color)
4. Show the message OSD position is
VX2433wm-1
at the center for 3 seconds.
5. Clean FIFO timing mode buffer
6. Execute Auto Image Adjust
Note: Memory Recall should not effect
on Language, Power Lock Settings
or Input Priority
The On-Screen Display (OSD) shall be an easy to use icon based menu through keypad OSD buttons or
remote control unit. The unit shall leave the factory with all OSD controls set to their default values.
VX2433wm-1
5.7 Upload firmware to MCU via VGA Cable
5.7.1 Connect ISP board between monitor and PC as below configure
LCD Monitor
D-Sub
ISP Board
Insert to Print
Port 25pin
VX2433wm-1
5.7.2 Using Novatek ISP Tool Update FW:
(1).Select “ISP”, Choose the corresponding firmware, load to MCU.
(2).Choose the corresponding firmware, load to MCU, Select “Run”, start ISP.
(3).When the picture show “End”, ISP finished.
VX2433wm-1
6. Troubleshooting Flow Chart
6.1 Common Acknowledge
z If you change the interface board, be sure that the U101, U103, U104 and U105 these four
components also changed to the new I/F board because there was program inside. If not,
please re-write EDID and upload firmware into U101 via VGA Cable.
z If you adjust clock and phase, please do it at the condition of Windows shut down pattern.
z If you confirm the R.G.B. color is normal or not, please do it under 16-grey scalar pattern.
z This LCM is analog interface. So if the entire screen is an abnormal color that means the
problem happen in the analog circuit part, if only some scale appears abnormal color that
stand the problem happen in the digital circuit part.
z If you check the H/V position, please use the crosshatch pattern.
z This LCM support more than 30 timing modes, if the input timing mode is out of specification,
the picture may appears abnormally.
z If brightness uneven, repairs Inverter circuit or change a new panel.
z If you find the vertical line or horizontal line lost on the screen, please change panel.
z If you find the speaker don’t working, please don’t plug in audio cable, unless change new
speaker.
VX2433wm-1
6.2 No Power & Power LED Off
No power
Check primary Check circuit Check IC802,
rectifier voltage if short C804, T801
Check F801,
P801,,RT801, D801
Check pin5 of
Check R833, R835,
IC802 voltage
R805, R834, R807
about 2.3V
Check pin4of IC802

Check R808,R806
voltage about300 V
Check pin7 of IC802

Check FB801,D803
voltage is 16V
Is there instantaneously
Check IC802
pulse wave on pin8
END
VX2433wm-1
6.3 DC output voltage is unstable
VX2433wm-1
6.4 Output power is unstable
VX2433wm-1
6.5 Backlight can’t be turned on
No raster?
Yes
LED Blue?
Yes
Backlight can’t
be turned on.
Yes
Is there 14Vdc No
voltage on pin9 Check power
of IC501?
Yes
Is there high-level voltage No Yes

Is Ok R503?
Check I/F
on pin8 of IC501?
Yes No
R503 open
Are connected rightly Connecting the

No
CN501, CN502? output connector
Yes
Is there instantaneously pulse

No Yes
wave on pin14, pin11 of IC501 Is Ok IC501? U501 fail
at the moment of restart?
No
IC501 fail
Yes
No T501 fail
Is T501 ok?
Yes
Check feedback circuit END
VX2433wm-1
6.6 Black Screen and backlight turn on
Black Screen
NG
Check VCC
Power Fail
5V
OK
࣠अंऀईࢽ࣐ࣳ࣠࣠
࣐࣐࣋ࣳࢽࣾऋँࢽ
NG
Check
ࣳ࣠࣠࣎
࣏࣎࣋ࣳࢽ
FB104
OK
Check
Check Reset
FB102 FB103
Waveform
NG
Check C153
OK
NG
Check Crystal
Check
Waveform
C157,C158,X101
OK
OK OK
Check CCFL Check Invert fail
Enable pin102 of
NG
NG
Check R103,R105,R106,
U108fail and Q103
VX2433wm-1
6.7 White Screen
White Screen
OK
LVDS cable Workmanship
reinsert
NG
OK
Change LVDS LVDS cable NG
cable
NG
OK
Check VLCD OK Check VLCD Panel Fail
Is 5V
singals
NG
Check panel Enable
of Panel Enable
OK
Check CN104
Check
Q101,Q104 and
END
VX2433wm-1
6.8 Bad Screen
Bad Screen
OK
LVDS able
C Workmanship
Reinsert
NG
hange LVDS
Cable
NG
NG
Check crystal:
check X101,C157
Pin116&pin117 C158
OK
checkU108and
SO/CS#/SCK/SI
SDO/SCZ/SCKSDI /RSTN
VX2433wm-1
7. Block Diagram
VX2433wm-1
8. Schematic Diagrams
POWER (DC TO DC)
VX2433wm-1
VGA-INPUT
VX2433wm-1
DVI-INPUT
VX2433wm-1
HDMI-INPUT
VX2433wm-1
SCALER
VX2433wm-1
AUDIO
VX2433wm-1
VX2433wm-1
POWER SUPPLY
VX2433wm-1
INVERTER SUPPLY
VX2433wm-1
9. PCB Layout Diagrams
MAIN BOARD - SILKSCREEN TOP
VX2433wm-1
MAIN BOARD - SILKCREEN BOTTOM
VX2433wm-1
POWER BOARD - SILKSCREEN TOP
VX2433wm-1
POWER BOARD - SILKSCREEN BOTTOM
VX2433wm-1
KEYPAD FOR FUNCTION - SILKSCREEN TOP KEYPAD FOR POWER - SILKSCREEN TOP
KEYPAD FOR FUNCTION - SILKSCREEN BOTTOM KEYPAD FOR POWER - SILKSCREEN BOTTOM
VX2433wm-1
10. Exploded Diagram and Exploded Parts List
VX2433wm-1
EXPLODED PARTS LIST ( VX2433wm-1/VX2433wm-CN)
ViewSonic Model Number: VS12324
Rev: 1a
ITEM ViewSonic P/N Ref.PN DESCREPTION Q'TY
1 C-00009284 714030024100R ASSY,FRONT,BEZEL,LP2447 1
2 B-00009290 792131500020R function-KEYPAD 1
3 NA 501020230300R key cover,,LP2447 1
4 E-00009253 631102240160R PANEL236" W (CMO901) 1
5 NA 509146306200R SCREW,P,CROSS,W/WAS,M3*6,Zn-Cc 7
6 B-00009424 792641300500R IF BOARD (W/DVI) 1
7 B-00009425 792641400500R POWER BOARD 1
8 NA 701000014600R ASSY,CHASSIS,W/ DVI,LP2447 1
9 E-00009255 618100200500R speaker 1
10 C-00009287 714050022600R ASSY,COVER,BACK,W/ DVI,LP2447 1
11 C-00009285 714011206600R ASSY,STAND,LP2447 1
12 C-00009286 714020019100R ASSY,BASE,LP2447 1
13 NA 509216610110R SCREW,F,CROSS,M4*10,BLK-NL (NYLOK) 4
14 CB-00008927 430300802770R power key pad line 1
15 NA 509000000700R BOLT,#4-40*11.8,Ni 4
16 NA 430300500530R IF key pad line 1
17 B-00009289 792131500010R power key pad 1
18 CB-00008926 430303002350R LVDS CABLE 1
VX2433wm-1
PACKING PART LIST ( VX2433wm/VX2433wm-CN )
Rev: 1a
Item ViewSonic P/N Ref. P/N Description Q'ty
1 CB-00008002 453030300120R AUDIO CABLE 1
2 A-00008111 453070800150R POWER CABLE 1
3 P-00009398 506060016710R CUSHION LEFT,LP2447 1
4 NA 506431008200R FILM PROTECTION PE 1
5 NA 714020018300R ASSY BASE VX2433wm 1
6 P-00009399 506120010900R BAG,PLASTICΔEPE+PE,L500xW670xT0.55mm,LP2447 1
7 A-00008411 703500009900R KIT ACCESSORY VX2433wm 1
8 P-00009400 506120010901R BAG,PLASTIC,L380xW330xT0.05mm,LP2447 1
9 CB-00008190 453030300370R DVI CABLE 1
10 CB-00008437 453010100380R VGA CABLE 1
11 P-00009397 506060016700R CUSHION RIGHT,LP2447 1
12 NA N/A MONITOR 1
13 P-00009396 506020029600R CARTON 1
14 NA 506440002300R CARTON LABEL 1
15 NA 506091000700R WARRANTY LABEL FOR CHINA 1
VX2433wm-1
11. Recommended Spare Parts List
RECOMMENDED SPARE PARTS LIST (VX2433wm-1/VX2433wm-CN)

Serial No. Prefix: VX2433wm-1 - R4F
Serial No. Prefix: VX2433wm-CN - R8W
Rev: 1a
Item Category Part Name Description ECR/ECN ViewSonic P/N Ref. P/N Ref. NO Compatibility Location Universal number# Remark
1 Accessories: Adapter KIT ACCESSORY VX2433 LP2447 A-00008411 703500009900R VSA,VSI,VSCN Main Source
2 [Adapter, Remote Power Cord PWR CORD 10A/125V BLK 6FT UL/CSA SVT 3Cx(USA) A-00008111 453070800150R Main Source
3 Controller, Power Power Cord PWRCORD 7A/125V BLK 6FT CNS VCTF 3Gx0.75(TWN) A-00006733 453070800480R Main Source
4 Cord, External Power Cord PWR CORD 16A/250V BLK 6FT VDE,H05VV-F 3G(Europe) A-00008279 453070801190R Main Source
5 Cables] Power Cord PWRCORD 10A/250V BLACK 6FT SAA,H05W-F/3G(Australia) A-00003671 453070800420R Main Source
6 Power Cord PWRCORD 16A/250V BLK 6FT KTL,H05VV-F 3Gx(Korea) A-00006734 453070800500R Main Source
7 Power Cord PWRCORD 10A/250V BLK 6FT CHINA.RVV 3Gx0.(China) A-00005255 453070800170R Main Source
8 Power Cord PWRCORD 5A/250V BLK 6FT UK3Gx.75mm(SP60/(Singapore) A-00003675 453070800230R Main Source
9 Audio Cable CABLE AUDIO 1P 6FT BLACK/GREEN CP03B06P0 CB-00008002 453030300120R VSA,VSI,VSCN Main Source
10 Signal Cable CABLE,D-SUB 15P MALE 6FT BLACK/BLUE, ROH(New) CB-00008437 453010100380R VSA,VSI,VSCN Main Source
11 Signal Cable CABLE,DVI-D 18+1P MALE 6FT BLACK , ROHS CB-00008190 453030300370R VSA,VSI,VSCN Main Source
12 PC Board Main Board PCBA,I/F BOARD,W/SPK,LP2347-527 ROHS B-00009424 792641300500R VSA,VSI,VSCN 6 1,2
13 Assembly: [All Power Board PCBA,P/I BOARD,W/SPK,LP2347-527 ROHS B-00009425 792641400500R VSA,VSI,VSCN 7 1,2
14 PCBA] Key Pad PCBA,POWER KEYPAD/B LE18L3-722 ROHS B-00009289 792131500010R VSA,VSI,VSCN 17 1,2
15 Key Pad PCBA,FUNTION KEYPAD/B,LE18L3-722 ROHS B-00009290 792131500020R VSA,VSI,VSCN 2 1,2
16 Cabinets: [Front Front Bezel ASSY,FRONT,BEZEL,LP2447 C-00009284 714030024100R VSA,VSI,VSCN 1 Main Source
17 Bezel, All Covers, Stand Assembly ASSY,STAND,LP2447 C-00009285 714011206600R VSA,VSI,VSCN 11 Main Source
18 Base Assembly] Base Assembly ASSY,BASE,LP2447 C-00009286 714020019100R VSA,VSI,VSCN 12 Main Source
19 Back Cover ASSY,COVER,BACK,W/ DVI,LP2447 C-00009287 714050022600R VSA,VSI,VSCN 10 Main Source
20 Hinge Cover ASSY,HINGE,LP2447 C-00009288 714000006000R VSA,VSI,VSCN Main Source
21 Cables: [All Flat Cable HRN LVDS FFC 30P 185mm W/TASTE&CORE&LOCK CB-00008926 430303002350R VSA,VSI,VSCN 18 Main Source
22 internal Wire HRN ASS'Y 2*4P TO 1*8P 197mm UL1571#28 CB-00008927 430300802770R VSA,VSI,VSCN 14 Main Source
23 Electronic Panel LCP 23.6"M236H1-L01-901(A)(CMO) ROHS E-00009253 631102240160R VSA,VSI,VSCN 4 1
24 Components: Panel LCP 23.6"M236H1-L01-902(A)(CMO) ROHS E-00009254 631102240170R VSA,VSI,VSCN 2
25 [LCD Panel, Speaker SPEAKER 2W 4ȍ 170ϟ395mm R/G/B W/CASE E-00009255 618100200500R VSA,VSI,VSCN 9 Main Source
26 Packing Material: Carton CARTON VX2433 LP2447 P-00009396 506020029600R VSA,VSI,VSCN Main Source
27 [Box, Foam, Bags] Cushion CUSHION,RIGHT,LP2447 P-00009397 506060016700R VSA,VSI,VSCN Main Source
28 Cushion CUSHION,LEFT,LP2447 P-00009398 506060016710R VSA,VSI,VSCN Main Source
29 PE Bag BAG,PLASTICΔEPE+PE,L500xW670xT0.55mm,LP P-00009399 506120010900R VSA,VSI,VSCN Main Source
30 PLASTIC BAG,PLASTIC,L380xW330xT0.05mm,LP2447 P-00009400 506120010901R VSA,VSI,VSCN Main Source
Remark 1: Base on CMO 24" panel
VX2433wm-1
BOM LIST ( VX2433wm-1/VX2433wm-CN)
Rev: 1a
Item ViewSonic P/N Ref. P/N Description Location Universal number# Q'ty
1 A-00008111 453070800150R PWR CORD 10A/125V BLK 6FT UL/CSA SVT 3Cx 100
2 CB-00008437 453010100380R CABLE,D-SUB 15P MALE 6FT BLACK/BLUE, ROH 100
3 CB-00008002 453030300120R CABLE AUDIO 1P 6FT BLACK/GREEN CP03B06P0 100
4 CB-00008190 453030300370R CABLE,DVI-D 18+1P MALE 6FT BLACK , ROHS 100
5 NA 453030300371R CABLE,DVI-D 18+1P MALE 6FT BLACK 100
6 NA 713100009800R ASSY,PACKAGE,PACK,VSA,VX2433(LP2447) 100
7 NA 506431008200R FILM,PROTECTION,UNPRINTED,555x327x0.1mm, 100
8 P-00009397 506060016700R CUSHION,RIGHT,LP2447 100
9 P-00009398 506060016710R CUSHION,LEFT,LP2447 100
10 P-00009399 506120010900R BAG,PLASTICΔEPE+PE,L500xW670xT0.55mm,LP 100
11 P-00009400 506120010901R BAG,PLASTIC,L380xW330xT0.05mm,LP2447 100
12 P-00009396 506020029600R CARTON VX2433 LP2447 100
13 NA 506250027600R LBL AGENCY VX2433 LP2447 100
14 NA 506440002300R LABEL,BLANK,76.2x76.2mm,LE1709(UPC) 100
15 NA 506440005200R LABEL,BLANK 49.5*24.5 BLANK LE2082(VA2 100
16 NA 506440002600R LABEL,BLANK,210x65mm,LE1709(PALLET) 4.2
17 NA 506250028000R LABEL POP feature VX2260wm(LP2137) 100
18 A-00008411 703500009900R KIT ACCESSORY VX2433 LP2447 100
19 NA 506070120900R MNL USER'S(CD), VX2433w(LP2447) 100
20 NA 506280302901R QSG VX2433w(LP2447) 100
21 NA 506420405200R INSERT SHEET, 1920*1080,LE21N1 100
22 NA 506180003000R BASE ATTCHMENT VX1933w(LE18L3) 100
23 NA 506030200901R SRS CARD FOR ViewSonic 100
24 NA 713010005500R ASSY, PACK,SEA, 20&40STD, VX2433(LP2447) 100
25 NA 506150006100R PALLET L1270*W1016*H130MM LE1939 2.1
26 NA 506039010460R CORNER PAPER1850x40x40xT5mm 8.3
27 NA 506039007200R CORNER PAPER 1200x50x50xT5mm LE1729 4.2
28 NA 506039007600R CORNER PAPER,900x50x50xT5mm, 4.2
29 NA 506038003500R CARDBOARD L1270xW1016xT4mm LE1939 2.1
30 NA 506036005900R CARDBOARD,L1190*W950*T7 2.1
31 NA 506431000300R FILM,PE 500mmx900M ROHS 0.2
32 NA 506380002100R TAPE WRAPPING TYPE(VIEWSONIC) 50mmx75M L 0.7
33 NA 506120100500R SEALED BAG ADHESIVE 330x230mm LE1918 2.1
34 NA 713010005501R ASSY, PACK,AIR, 20&40STD, VX2433(LP2447) 100
35 NA 506150006100R PALLET L1270*W1016*H130MM LE1939 4.2
36 NA 506039007200R CORNER PAPER 1200x50x50xT5mm LE1729 8.3
37 NA 506039007600R CORNER PAPER,900x50x50xT5mm, 25
38 NA 506038003500R CARDBOARD L1270xW1016xT4mm LE1939 4.2
39 NA 506036005900R CARDBOARD,L1190*W950*T7 4.2
40 NA 506431000300R FILM,PE 500mmx900M ROHS 0.1
41 NA 506380002100R TAPE WRAPPING TYPE(VIEWSONIC) 50mmx75M L 0.4
42 NA 506120100500R SEALED BAG ADHESIVE 330x230mm LE1918 4.2
43 NA 714076650000R ASSY,FINAL(B,A)W/SPK,LP2347-527(USA/VX24 100
44 C-00009284 714030024100R ASSY,FRONT,BEZEL,LP2447 100
45 NA 750010203200R SUB-ASSY,FRONT,BEZEL,PRINTING,LP2447 100
46 NA 501010224900R FRONT,BEZEL,LP2447 100
47 NA 501120110700R LENS,LP2447 100
48 NA 501030212200R FUNCTION VA1933 100
49 NA 501030212201R POWER KEY VA1933 100
50 NA 506102000300R LOGO PLATE VIEWSONIC LE1709 100
51 C-00009287 714050022600R ASSY,COVER,BACK,W/ DVI,LP2447 100
52 NA 501020230301R COVER,BACK,W/ DVI,LP2447 100
53 NA 502020301400R BRACKET VESA LE1729 ROHS 400
54 C-00009285 714011206600R ASSY,STAND,LP2447 100
55 NA 501260211700R STAND,LP2447 100
56 C-00009288 714000006000R ASSY,HINGE,LP2447 100
57 NA 509412610500R SCREW,B,CROSS,T.T-4*10,BLK ,ROHS 300
ˣ˴˺˸ʳ˄ʳ̂˹ʳ˅
VX2433wm-1
Item ViewSonic P/N Ref. P/N Description Location Universal number# Q'ty
58 C-00009286 714020019100R ASSY,BASE,LP2447 100
59 NA 501240214600R BASE,LP2447 100
60 NA 503020006300R RUBBER FOOT L14.8*W9.6*T3.5mm ,LE19E3 600
61 NA 501020230300R key cover,,LP2447 100
62 NA 509216610510R SCREW,F,CROSS,M4*10,BLK-NL(NYLOK) 400
63 NA 714086650000R ASSY,PANEL(A)W/SPK,LP2347-527(VX2433WM) 100
64 NA 511150102610R FOIL,AL.,DOUBLE COND.,RIGHT,LE2239 100
65 NA 511150102600R FOIL,AL.,DOUBLE COND.LEFT,LE2239 100
66 NA 511150101800R FOIL,AL.,DOUBLE COND.,60x35xT0.07mm, LE2 100
67 NA 506381000700R TAPE,ACE,45mmx30M(PC=10x45mm),LE1709 ROH 200
68 NA 509146306200R SCREW,P,CROSS,W/WAS,M3*6,Zn-Cc 700
69 NA 509000000700R BOLT,#4-40x11.8,Ni FOR D-SUB/DVI CONN.RO 400
70 NA 701000014600R ASSY,CHASSIS,W/ DVI,LP2447 100
71 NA 502090103400R CHASSIS,W/ DVI,LP2447 100
72 NA 502020100600R BRACKET,HINGE,LP2447 100
73 NA 505040209000R INSULATOR,MYLAR,L21*W18*T0.5,LE19F6 100
74 B-00009424 792641300500R PCBA,I/F BOARD,W/SPK,LP2347-527 ROHS 100
75 B-00009425 792641400500R PCBA,P/I BOARD,W/SPK,LP2347-527 ROHS 100
76 B-00009290 792131500020R PCBA,FUNTION KEYPAD/B,LE18L3-722 ROHS 100
77 B-00009289 792131500010R PCBA,POWER KEYPAD/B LE18L3-722 ROHS 100
78 E-00009253 631102240160R LCP 23.6"M236H1-L01-901(A)(CMO) ROHS 100
79 E-00009254 631102240170R LCP 23.6"M236H1-L01-902(A)(CMO) ROHS 100
80 CB-00008926 430303002350R HRN LVDS FFC 30P 185mm W/TASTE&CORE&LOCK 100
81 NA 503110000300R RUBBER SILICON THERMAL CONDUCT 28X20XT7 100
82 NA 430300500530R HRN ASS'Y 5P 360mm UL1571#28 100
83 CB-00008927 430300802770R HRN ASS'Y 2*4P TO 1*8P 197mm UL1571#28 100
84 E-00009255 618100200500R SPEAKER 2.5W 4ȍ 170ϟ395mm R/G/B W/CASE 100
ˣ˴˺˸ʳ˅ʳ̂˹ʳ˅
VX2433wm-1
* Reader’s Response*
Dear Readers:
Thank you in advance for your feedback on our Service Manual, which allows continuous improvement
of our products. We would appreciate your completion of the Assessment Matrix below, for return to
ViewSonic Corporation.
Assessment
A. What do you think about the content of this Service Manual?
Unit Excellent Good Fair Bad
1. Precautions and Safety Notices
2. Specification
3. Front Panel Function Control Description
4. Circuit Description
5. Adjustment Procedure
6. Troubleshooting Flow Chart
7. Block Diagrams
8. Schematic Diagrams
9.PCB Layout Diagrams
10. Exploded Diagram and Exploded Parts List
11. Recommended Spare Parts List
B. Are you satisfied with this Service Manual?

Item Excellent Good Fair Bad
1. Service Manual Content ʳ ʳ ʳ ʳ
2. Service Manual Layout ʳ ʳ ʳ ʳ
3. The form and listing ʳ ʳ ʳ ʳ
C. Do you have any other opinions or suggestions regarding this service manual?
Reader’s basic dada:

Name: Title:
Company:
Add:
Tel: Fax:
E-mail:
After completing this form, please return it to ViewSonic Quality Assurance in the USA at facsimile
1-909-839-7943. You may also e-mail any suggestions to the Director, Quality Systems & Processes
(marc.maupin@viewsonic.com)
VX2433wm-1

Service Manual: Viewsonic Vx2433Wm-1 Vx2433Wm-Cn

Uploaded by

Copyright:

Available Formats

Service Manual: Viewsonic Vx2433Wm-1 Vx2433Wm-Cn

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Service Manual: Viewsonic Vx2433Wm-1 Vx2433Wm-Cn

Uploaded by

Copyright:

Available Formats

Service Manual

(VX2433wm-1_VX2433wm-CN _SM Rev. 1b Feb. 2009)

Product disposal at end of product life

1a 11/27/2008 Initial Release Eden Chang

Revise “5.7.2 Using Novatek ISP Tool Update

1. Precautions and Safety Notices ......................................................................................... 1

3. Front Panel Function Control Description ..................................................................... 13

4. Circuit Description ............................................................................................................. 17

6. Trouble Shooting Flow Chart ............................................................................................ 33

7. Block Diagrams ................................................................................................................ 40

8. Schematic Diagrams ........................................................................................................ 50

9. PCB Layout Diagrams ...................................................................................................... 56

10. Exploded Diagram And Spare Parts List........................................................................ 60

11. Recommended Spare Parts List .................................................................................... 71

2. PRODUCT SAFETY NOTICE

Size ʳ 23.6” Wide Color a-Si TFT Active Matrix LCD

Display area ʳ ʳ 525.22(W) x 297.22(H) mm

Optimum Resolution ʳ 1920x1080(WUXGA)

Pixel Pitch 0.2715(H) x 0.2715(V) mm

Glass Treatment ʳ Anti-Glare, Hard coating (3H),Haze25

Contrast Ratio CR >= 10 1000 :1

Dynamic Contrast ʳ 20000:1 (typ.)

Viewing Angle 170/160 (degrees; typ)

Colors 16.7Mcolors (6 bit +Hi FRC panel)

Luminance 300 cd/m2 @8.0mA(typ.)

Response Time On/Off 5 ms (typ.) /10 ms (max.)

Backlight Life 50000 Hrs (Typ) @7.0mA

Mercury 3.6 mg per lamp(max)

2 INPUT SIGNAL Video RGB Analog (0.7 / 1.0 Vp-p , 75 ohms),

DVI-D / HDMI (TMDS, 100ohms)

Sync Separate Sync / Composite Sync / SOG

3 COMPATIBILITY PC ʳ PC Compatibles (from VGA up to 1920x1080 Non Interlaced)

Mac Power Mac (up to 1920x1080 )

4 Recommended 1920 x 1080 @ 60Hz

6 CONNECTORS Video ʳ Analog DB-15

ʳ HDMI ( Supported HDMI ver. 1.3 spec)

Audio Audio Out 3.5 mm jack (blue)

Audio In 3.5 mm jack (green

Power Internal Power Adapter, 3-pin plug (CEE22)

7 POWER Voltage ʳ AC 100-240V (Universal); 50-60 Hz

Consumption Typ/Max 45 W (typ.) / 55 W (Max)

ECO Mode Optimize 37 W (typ.)

Height Adjust N/A

9 CONTROLS Physical Key buttons [ ]

OSD Function Main Menu

ʳ Auto Image Adjust

D-SUB, DVI,HDMI PC,HDMI AV

sRGB, 9300K, 7500K, 6500K, 5000K, User Color [R, G, B]

Manual Image Adjust

H/V Position, Horizontal Size, Fine Tune, Sharpness, Dynamic

Contrast, Response Time, Aspect ratio, Display Mode, Eco mode

Language Select, Resolution Notice, OSD Position, OSD Time Out,

OSD Background, Sleep

Short cut key Memory Recall

[Dn] : To immediately activate Audio menu.

[up] : To immediately activate Contrast menu. It should be change to

Brightness OSD by push button [2]

between HDMI and jack plug

[Up] or [Dn] : Contrast / Brightness