Nothing Special   »   [go: up one dir, main page]
Scribd Logo
Upload

Welcome to Scribd!

  • 736 views

    Graseby 1200: Large Volume Infusion Pump

    Uploaded by

    gongyin HE

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Graseby 1200: Large Volume Infusion Pump

    Uploaded by

    gongyin HE
    736 views6 pages

    Original Title

    IN193909GB-052017

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    736 views6 pages

    Graseby 1200: Large Volume Infusion Pump

    Uploaded by

    gongyin HE

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 6

    Graseby™ 1200

    Large Volume Infusion Pump


    Quick Reference Guide

    Read the entire Instruction Manual before operating the Graseby™


    1200 Infusion Pump . Failure to properly follow warnings, cautions
    and instructions could result in death or serious injury to the patient.
    The Graseby™ 1200 is a volumetric infusion pump that provides
    accurate and reliable infusions at a rate of 1 - 1200 mL/h

    Start the pump

    Before starting, the infusion pump must be placed horizontally for


    use, and should be placed on a stable surface or attached to an IV
    pole. Please keep a safe distance between the infusion pump and the
    patient to help prevent the IV pole from falling over onto the patient.
    1. Connect the AC power supply plug to the pump
    2. Press the Power key for two seconds
    3. The pump switches on and automatically performs a self-check
    4. After the self-check, continue installing the infusion tubing if
    there isn’t an alarm. Make sure the infusion tubing is in good
    shape before starting the pump.
    Install the infusion tubing

    Ensure that the drip chamber is located between the infusion bottle/
    bag and the pump, while the roller clamp is located between the
    patient and the pump. The infusion tubing should be inserted in
    accordance with the infusion direction indicator on the pump.
    1. Hang the infusion bottle (bag) filled with medication on the IV
    pole, close the flow regulator, and make sure the drip chamber is
    about half filled.
    2. Lift the pump lock handle to open the pump door

    Lock handle

    3. Position the infusion tubing in the power box slot, lift up the fluid
    clamp, and press the infusion tubing firmly into the ultrasonic
    sensor slot.

    Power box

    Fluid clamp

    Flow regulator

    4. Lift the lock handle to make sure the retractor clasps the door
    pin, then press the lock handle down to close the pump door. At
    this time, the surface of the lock handle should be flush with the
    pump’s outer case.
    Program a Continuous Infusion

    The Graseby™ 1200 infusion pump can be programmed to infuse in


    two ways:
    1. Set the infusion volume and rate, and the infusion time will
    automatically be calculated
    2. Set the infusion volume and infusion time, and the infusion rate
    will automatically be calculated
    After installing the infusion tubing, set up the infusion pump
    1. Use to input the infusion rate in mL/h. The rate unit is
    only altered at a configuration interface
    2. Move cursor below using the key
    3. Use to input the infusion volume in mL. The pump will
    automatically calculate the infusion time based on the infusion
    rate and infusion volume
    4. The brand of the infusion tubing can only be set in the
    configuration screen. It is recommended to set the parameters
    such as brand, occlusion grade, rate unit and KVO rate before
    setting the rate, infusion, and other parameters.

    Priming the Infusion Set

    After the infusion tubing is installed and the pump is programmed,


    prime the line to remove any remaining air in the tubing before
    connecting to the patient.
    While priming, ensure that the tubing is not connected to
    the patient.
    1. Open the flow regulator between the patient and the
    infusion pump
    2. Press the Priming/Bolus key twice and hold at the second
    PRIMING
    /TUBING

    time to prime the infusion tube at the rate of 1000 mL/h


    3. Release the Priming/Bolus key when you observe that
    PRIMING
    /TUBING

    the air has been expelled and fluid begins to drip from the end
    of the tubing.
    Note: Priming volume is not calculated in the cumulative volume
    Calibration of brand and serial number of
    infusion tubing
    The infusion tubing brand should be updated and calibrated.
    If you’re using other brands, calibration should be done after
    selecting a serial number at the first use. The calibration methods
    are as follows:
    1. At the stop status, press the move cursor key
    and select key SELECT at the same time to enter the rate
    calibration screen
    2. Load the infusion tubing
    3. Set the serial number, rate and test volume (e.g. No. 02 Lifeline,
    calibration rate 200 mL/h, calibration volume 20 mL)
    4. Press the Start key to start the calibration. Once it reaches
    to the test volume, press the Stop key immediately. The first
    calibration is completed .
    5. Repeat steps 3 and 4 to calibrate the tubing again
    6. After finishing the second calibration, “OK” is shown on the
    screen, if successful; move the cursor to “OK” by pressing the
    Move cursor key .
    7. If the same brand of infusion tube is used after calibration,
    only the brand or serial number will have to be selected before
    use. In consideration of the manufacturer’s accuracy factor for
    the infusion set, it is advised to calibrate all brands of infusion
    tubing before use. For more details on the calibration procedure,
    please refer to the Instruction Manual.

    Start the infusion

    1. Set up the infusion pump and make sure the infusion tubing has
    been primed
    2. Connect the infusion tubing to the patient and open the
    flow regulator
    3. Press the green Start key and the infusion will begin
    4. The water droplet symbol flowing on the left of the LCD display
    screen indicates the infusion pump is working. After 15 seconds
    in the screensaver mode, the pump screen displays the infusion
    rate values, the infusion rate unit, infusion time left and the
    dynamic water droplet symbol, as shown in Figure 1.

    High: 120 kPa; Middle: 66.7 kPa; Low:10 kPa

    Infusion
    rate unit
    Infusion Rate
    ml/h 100 Infusion rate value

    Dynamic drop Infusion


    symbol Time Left 09h59 Infusion time left

    Figure 1: Pump screensaver


    Infusion program setting

    The Graseby™ 1200 infusion pump can be used for consecutive


    infusions through two different infusion programs. Before setting up
    the infusion pump,first install the infusion tubing.
    1. In the programming mode, press the Select key until the screen
    is changed to the infusion program setting screen
    2. To set Infusion Program 1: Use to input the infusion
    rate and press to move the cursor to the infusion volume.
    Use to input the infusion volume and press to move
    the cursor to the infusion rate for Infusion Program 2.
    3. To set Infusion Program 2: Use the same method from Infusion
    Program 1 to set the infusion rate and infusion volume for
    Infusion Program 2.
    4. After the correct infusion program is displayed, press to
    move the cursor to “OK”, then press the Select key to confirm
    and save the infusion program setting and return to the main
    screen. On the Infusion Program Setting screen, press the
    Stop key and then the Select key concurrently to clear the
    infusion program.
    Note: When infusion programs are applied, the infusion pump
    will perform Infusion Program 2 automatically after the end of
    Infusion Program 1.
    Alarms

    If the infusion pump alarms, listen for the beeps and check the
    display screen for alarm messages or symbols.

    Alarms Tips/reason Operation


    The battery capacity Press the Mute key ,
    Battery low is low/infusion pump connect the pump to an
    Beep-beep-beep could work about AC power supply as soon
    30 minutes as possible
    Battery depleted The battery capacity Connect the infusion pump
    is empty, the infusion to an AC power supply
    Beep pump stops immediately
    Nearly completed The infusion is Press the Mute key ,
    infusion about to complete prepare to stop
    Beep-beep-beep in 3 minutes the infusion
    Completed The infusion is
    infusion completed, the Press the Stop key to
    pump will operate stop the infusion
    Beep-beep-beep in the KVO rate
    Turn off the flow regulator
    and press the Stop key
    Tubing route . After the occlusion is
    occlusion The infusion tubing or
    eliminated, open the flow
    cannula is blocked
    Beep-beep-beep regulator and press the
    Start key to continue
    the infusion or start over.
    Press the Mute key to
    Forget to operate The pump has been
    clear the alarm and start
    left idle for 2 mins
    Beep-beep-beep the infusion or close the
    without any operation
    infusion pump

    The door isn’t closed, Press the Stop key


    The door to stop infusion or
    isn’t closed the infusion stops
    or the infusion close the door and
    Beep-beep-beep cannot begin repress. Start key
    to continue infusion.

    PRODUCT(S) DESCRIBED MAY NOT BE LICENSED OR


    AVAILABLE FOR SALE IN CANADA AND OTHER COUNTRIES

    Smith Medical EC Authorized MZHCCA-0009


    International Representative
    1500 Eureka Park, Smiths Medical
    Lower Pemberton International Ltd.
    Ashford Kent, TN25 4BF TN25 4BF, UK
    Tel: +44 (0)845 850 0445 Tel: +44 (0) 1233 722100
    www.smiths-medical.com

    Find your local contact information at:


    www.smiths-medical.com/customer-support
    Smiths Medical is part of the global technology business Smiths Group plc. Please see
    the Instructions for Use/Operator’s Manual for a complete listing of the indications,
    contraindications, warnings and precautions. Graseby and the Smiths Medical design mark are
    trademarks of Smiths Medical. The symbol ® indicates the trademark is registered in the U.S.
    Patent and Trademark Office and certain other countries. All other names and marks mentioned
    are the trademarks or service marks of their respective owners. ©2017 Smiths Medical.
    All rights reserved. IN193909GB-052017

    You might also like