Loctite 567™: Technical Data Sheet
Loctite 567™: Technical Data Sheet
Loctite 567™: Technical Data Sheet
LOCTITE® 567™
December-2013
l
ee
generation, marine, automotive, industrial equipment, gas Brass
St
compression and distribution industries. It is also 0
recommended for industrial plant fluid power systems. 1min 5min10min 30min 1h 3h 6h 24h 72h
Cure Time
UL Classification
Classified by Underwriters Laboratories Inc.® MH8007 - Cure Speed vs. Temperature
The rate of cure will depend on the temperature. The graph
Fire hazard is small. No flash point in liquid state. Ignition below shows the breakaway strength developed with time at
temperature 455°C. For use in devices handling gasoline, different temperatures on 3/8 NPT steel pipe tees and plugs
petroleum oils, natural gas (pressure not over 300 and tested according to ASTM D6396.
PSIG), butane and propane not exceeding 2 in. pipe size.
100
% of Full Strength on Steel
25
closely fitting metal parts in devices handling natural gas and
methane, gasoline and petroleum oils, and propane and
butane at pressures not exceeding 13,790 kPa. Ignition 0
temperature greater than 460 °C. Classed less than 10 below 1min 5min10min 30min 1h 3h 6h 24h 72h
Cure Time
paraffin oil with respect to fire hazard. Note: This is a regional
approval. Please contact your local Technical Service Center
for more information and clarification
TDS LOCTITE® 567™, December-2013
Ethanol 22 85 85 85
Acetone 22 75 70 60
9™
64
™
75 1,1,1 Trichloroethane 22 90 90 85
71
r7
74
Water/glycol 50/50 87 100 75 75
ato
or
tiv
E85 Ethanol fuel 22 N/A 85 130
at
50
Ac
tiv
or B100 Bio-Diesel 22 N/A 105 90
Ac
ivat
act DEF (AdBlue® ) 22 N/A 130 120
25 No
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
0
1min 5min10min 30min 1h 3h 6h 24h 72h and/or oxygen rich systems and should not be selected as
Cure Time a sealant for chlorine or other strong oxidizing materials.
TYPICAL PROPERTIES OF CURED MATERIAL For safe handling information on this product, consult the
Physical Properties: Safety Data Sheet (SDS).
Coefficient of Thermal Expansion, 80×10-6 Where aqueous washing systems are used to clean the
ISO 11359-2, K-1
surfaces before bonding, it is important to check for
Coefficient of Thermal Conductivity, ISO 8302, 0.1
compatibility of the washing solution with the adhesive. In
W/(m·K)
some cases these aqueous washes can affect the cure and
Specific Heat, kJ/(kg·K) 0.3
performance of the adhesive.
TYPICAL PERFORMANCE OF CURED MATERIAL This product is not normally recommended for use on plastics
Adhesive Properties (particularly thermoplastic materials where stress cracking of
After 24 hours @ 22 °C the plastic could result). Users are recommended to confirm
Breakaway Torque, ISO 10964: compatibility of the product with such substrates.
3/8 x 24 steel nuts (grade N·m ≥1.7LMS
2) and bolts (grade 2) (lb.in.) (≥15) Directions for use:
After 4 hours @ 22 °C For Assembly
Breakaway Torque, ISO 10964: 1. For best results, clean all surfaces (external and internal)
3/8 x 24 steel nuts (grade N·m ≥0.3LMS with a LOCTITE® cleaning solvent and allow to dry.
2) and bolts (grade 2) (lb.in.) (≥2.6) 2. If the material is an inactive metal or the cure speed is
too slow, spray with Activator 7471™ or
TYPICAL ENVIRONMENTAL RESISTANCE 7649™ and allow to dry.
Cured for 72 hours @ 22 °C 3. Apply a 360° bead of product to the leading threads of
Breakloose Torque, ISO 10964, Pre-torqued to 1.1 N·m: the male fitting, leaving the first thread free. Force the
M10 steel fasteners (degreased) material into the threads to thoroughly fill the voids. For
bigger threads and voids, adjust product amount
accordingly and apply a 360° bead of product on the
Heat Aging female threads also.
Aged at temperature indicated and tested @ 22 °C 4. Using compliant practices, assemble and wrench tighten
fittings in accordance with manufacturers
250 recommendations.
% Initial Strength @ 22 °C
For Cleanup except if otherwise explicitly agreed and except in relation to death or personal
injury caused by our negligence and any liability under any applicable mandatory
1. Cured product can be removed with a combination of product liability law.
soaking in a Loctite solvent and mechanical abrasion In case products are delivered by Henkel Corporation, Resin Technology
such as a wire brush. Group, Inc., or Henkel Canada Corporation, the following disclaimer is
applicable:
The data contained herein are furnished for information only and are believed to
be reliable. We cannot assume responsibility for the results obtained by others
Loctite Material SpecificationLMS over whose methods we have no control. It is the user's responsibility to
LMS dated September-1, 1995. Test reports for each batch determine suitability for the user's purpose of any production methods mentioned
are available for the indicated properties. LMS test reports herein and to adopt such precautions as may be advisable for the protection of
property and of persons against any hazards that may be involved in the handling
include selected QC test parameters considered appropriate to and use thereof. In light of the foregoing, Henkel Corporation specifically
specifications for customer use. Additionally, comprehensive disclaims all warranties expressed or implied, including warranties of
controls are in place to assure product quality and merchantability or fitness for a particular purpose, arising from sale or use
consistency. Special customer specification requirements may of Henkel Corporation’s products. Henkel Corporation specifically
disclaims any liability for consequential or incidental damages of any kind,
be coordinated through Henkel Quality. including lost profits. The discussion herein of various processes or
compositions is not to be interpreted as representation that they are free from
Storage domination of patents owned by others or as a license under any Henkel
Store product in the unopened container in a dry location. Corporation patents that may cover such processes or compositions. We
recommend that each prospective user test his proposed application before
Storage information may be indicated on the product container repetitive use, using this data as a guide. This product may be covered by one or
labeling. more United States or foreign patents or patent applications.
Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or Trademark usage
greater than 28 °C can adversely affect product properties. Except as otherwise noted, all trademarks in this document are trademarks of
Material removed from containers may be contaminated during Henkel Corporation in the U.S. and elsewhere. ® denotes a trademark
use. Do not return product to the original container. Henkel registered in the U.S. Patent and Trademark Office.
Corporation cannot assume responsibility for product which
has been contaminated or stored under conditions other than Reference 1.5
those previously indicated. If additional information is required,
please contact your local Technical Service Center or
Customer Service Representative.
Conversions
(°C x 1.8) + 32 = °F
kV/mm x 25.4 = V/mil
mm / 25.4 = inches
µm / 25.4 = mil
N x 0.225 = lb
N/mm x 5.71 = lb/in
N/mm² x 145 = psi
MPa x 145 = psi
N·m x 8.851 = lb·in
N·m x 0.738 = lb·ft
N·mm x 0.142 = oz·in
mPa·s = cP
Note:
The information provided in this Technical Data Sheet (TDS) including the
recommendations for use and application of the product are based on our
knowledge and experience of the product as at the date of this TDS. The product
can have a variety of different applications as well as differing application and
working conditions in your environment that are beyond our control. Henkel is,
therefore, not liable for the suitability of our product for the production processes
and conditions in respect of which you use them, as well as the intended
applications and results. We strongly recommend that you carry out your own
prior trials to confirm such suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or any other
written or oral recommendation(s) regarding the concerned product is excluded,
except if otherwise explicitly agreed and except in relation to death or personal
injury caused by our negligence and any liability under any applicable mandatory
product liability law.
In case products are delivered by Henkel Belgium NV, Henkel Electronic
Materials NV, Henkel Nederland BV, Henkel Technologies France SAS and
Henkel France SA please additionally note the following:
In case Henkel would be nevertheless held liable, on whatever legal ground,
Henkel’s liability will in no event exceed the amount of the concerned delivery.
In case products are delivered by Henkel Colombiana, S.A.S. the following
disclaimer is applicable:
The information provided in this Technical Data Sheet (TDS) including the
recommendations for use and application of the product are based on our
knowledge and experience of the product as at the date of this TDS. Henkel is,
therefore, not liable for the suitability of our product for the production processes
and conditions in respect of which you use them, as well as the intended
applications and results. We strongly recommend that you carry out your own
prior trials to confirm such suitability of our product.
Any liability in respect of the information in the Technical Data Sheet or any other
written or oral recommendation(s) regarding the concerned product is excluded,