SP14-15 Rp2 4"3X380-415/50 4.0kW: Grundfos Pump 98699358
SP14-15 Rp2 4"3X380-415/50 4.0kW: Grundfos Pump 98699358
SP14-15 Rp2 4"3X380-415/50 4.0kW: Grundfos Pump 98699358
Thank you for your interest in our products. Please contact us for more information, or visit our website
https://www.lenntech.com/grundfos/SPFAM/98699358/SP-14-15.html
info@lenntech.com
tel. +31 152 610 900
fax. +31 152 616 289
Submersible borehole pump, suitable for pumping clean water. Can be installed vertically or
horizontally. All steel components are made in stainless steel, EN 1.4301 (AISI 304), that ensures high
corrosive resistance. This pump carries drinking water approval.
The pump is fitted with a 4 kW MS4000 motor with sand shield, mechanical shaft seal, water-lubricated
journal bearings and a volume compensating diaphragm. The motor is a canned type submersible
motor offering good mechanical stability and high efficiency. Suitable for temperatures up to 40 °C.
The motor is not fitted with a temperature sensor. If temperature monitoring is desired, a Pt1000 sensor
can be fitted.
The motor is for direct-on-line starting (DOL).
Pump
All pump surfaces that are in contact with pumped liquids are made in stainless steel which makes
them corrosion- and wear-resistant. The corrosion diagram below shows the capabilities of the pump
and motor in relation to the temperature in Celsius (y-axis) and the concentration of chloride in ppm
(x-axis).
In case the pump is used for pumping water with high content of hydrocarbons or solvents, Grundfos
offers FKM rubber parts (Fluorocarbon) which are oil and temperature-resistant up to 90 °C.
The pump is built with octagonal bearings with sand flush channels that minimise wear. As wear of the
pump is inevitable, the pump design allows for easy replacement of all internal wear parts (bearings,
impeller, wear rings and seal rings) to maintain high performance and a long lifetime.
The suction interconnector is fitted with a strainer to prevent large particles from entering the pump. The
suction interconnector is designed to comply with NEMA standards for motor mounting/dimensions.
Motor
The stator is hermetically encapsulated in stainless steel and the windings are embedded in polymer
compound. This results in high mechanical stability, optimum cooling and reduces the risk of short
circuits in the windings.
The shaft seal is a tungsten carbide/ceramic replaceable mechanical shaft seal. The material
combination provides optimum sealing, resistance and long life. Together with the shaft seal housing,
the sand shield forms a labyrinth seal, which during normal operating conditions prevents penetration of
sand particles into the shaft seal.
The motor can be fitted with a Pt100 or Pt1000 sensor that together with a control unit ensures that the
maximum operating temperature conditions are not exceeded.
Liquid:
Pumped liquid: Water
Maximum liquid temperature: 40 °C
Max liquid t at 0.15 m/sec: 40 °C
Liquid temperature during operation: 20 °C
Density: 998.2 kg/m³
Technical:
Rated flow: 14 m³/h
Rated head: 65 m
Shaft seal for motor: HM/CER
Approvals on nameplate: CE,EAC
Curve tolerance: ISO9906:2012 3B
Motor version: T40
Materials:
Pump: Stainless steel
EN 1.4301
AISI 304
Impeller: Stainless steel
EN 1.4301
AISI 304
Motor: Stainless steel
DIN W.-Nr. 1.4301
AISI 304
Installation:
Pump outlet: RP2
Motor diameter: 4 inch
Electrical data:
Motor type: MS4000
Rated power - P2: 4 kW
Power (P2) required by pump: 4 kW
Mains frequency: 50 Hz
Rated voltage: 3 x 380-400-415 V
Rated current: 9.75-9.60-9.80 A
Starting current: 460-500-530 %
Cos phi - power factor: 0.85-0.80-0.77
Rated speed: 2850-2865-2875 rpm
Start. method: direct-on-line
Others:
Minimum efficiency index, MEI ≥: 0.50
ErP status: EuP Standalone/Prod.
Net weight: 38 kg
Gross weight: 72.1 kg
Shipping volume: 0.264 m³
Danish VVS No.: 388482015
90
80
70
60
50 100
40 80
30 60
20 40
10 20
0 0
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Q [m³/h]
P
[kW]
5.0
4.5
P1
4.0
3.5
P2
3.0
2.5
2.0
1.5
1.0
0.5
Model: A
30 60
Valve: YES
Motor version: T40
20 40
Materials:
Pump: Stainless steel 10 20
EN 1.4301
AISI 304 0 0
0 2 4 6 8 10 12 14 16 Q [m³/h]
Impeller: Stainless steel
P
EN 1.4301 [kW]
AISI 304 5
P1
Motor: Stainless steel
4
DIN W.-Nr. 1.4301
AISI 304 3
P2
Installation:
Pump outlet: RP2 2
Motor diameter: 4 inch
Liquid: 95
1
RP2
101
0
Maximum liquid temperature: 40 °C
Max liquid t at 0.15 m/sec: 40 °C RP2
Liquid temperature during operation: 20 °C 101 GN
M
3
cos phi
0.8 16
eta
0.6 12
0.4 8
0.2 4
0.0 0
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4 P2 [kW]
n P1
[rpm] [kW]
n
2800 8
P1
2600 6
2400 4
2200 2
2000 0
RP2
101 GN
1363
1940
577
95
251a
251d
77
28
7
7a 17
301a 219
92 301a
11
92
9
51
11b
105
215a
100
215
49
18
66a
45
67
530a
530
215a 217
6
531a
531
534
534a
3 2 1
TM058200
Printed from Grundfos Product Centre [2018.06.003] 9/10
Exploded view ( TM057026 for MGE model H/I )
251d
251b
291
290
287
277a
287a 273b
293 502
277
252a 286
273a
273
266
275a
268
268a
289a
289
251a 288b
288
288a
252b
159e
150
152
151
157 156
156c
158
185
154
178
172
187
153 191
188
156d
156b
192
156c
159d