SRP PUMP ASSEMBLY Parts and Accessories Catalogue
SRP PUMP ASSEMBLY Parts and Accessories Catalogue
SRP PUMP ASSEMBLY Parts and Accessories Catalogue
Accessories
Special Material Size Material / ID Condition
Finding the
Part Number: X 00 X 0 X
Commodity Number Length
www.Q2als.com | ii
Guides Plugs
Valve Rod, Box End, API G11. . . . . . . . . . . . . . . . . . . . . . . . . . 26 Pull, API P11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Valve Rod, Box End, Vertical Ported. . . . . . . . . . . . . . . . . . . . 26 Seat, Recessed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Valve Rod, Box End, Sand Check. . . . . . . . . . . . . . . . . . . . . . . 26 Seat, API P12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Pull Tube, Box End. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Valve Rod, Pin End. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Plungers
Pull Tube, Pin End . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Box End, Metal Sprayed, API P23. . . . . . . . . . . . . . . . . . . . . . 39
Pin End, API P21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Hold-Down Assemblies
Seating, API Type, 3 Cup, Type “HR”, Rod Pump. . . . . . . . . . 28 Rods
Seating, 5 Cup, Type “HR”, Rod Pump . . . . . . . . . . . . . . . . . . 28 Valve, API R11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Seating, 3 Cup, Type “O”, Rod Pumps. . . . . . . . . . . . . . . . . . . 29 Polish. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Seating, For Non-API Nipple, 3 Cup, Rod Pump . . . . . . . . . . 29 Pony (Pick – Up Sub). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Seating, Metal Friction Ring Type, Insert Pump . . . . . . . . . . 30
Seating, API Type, 2-Cup, Type “HR”, Tubing Pump . . . . . . . 31 Seating Cups
Seating, Metal Friction Ring Type, 2 Wide Ring, Type “0” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Tubing Pump. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Type “HR”. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Mechanical, API Type Top Lock, API S21 . . . . . . . . . . . . . . . . 32
Mechanical Bottom Lock, Tubes
API S21 Top Lock Converted to Bottom Lock . . . . . . . . . . . 32 Pull, API T11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Pacific Type, Insert Pump,
Combination Mechanical and Seating Cups. . . . . . . . . . . . 33 Accessories
Mechanical, API Type Bottom Lock, API S22. . . . . . . . . . . . . 33
Q-Shear Tool, Woosley Type. . . . . . . . . . . . . . . . . . . . . . . . . . 44
Standing Valve, TH, API P31 Tap Type . . . . . . . . . . . . . . . . . . 44
Nipples Q-Tubing Drain. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Seating, Cup Type, Rod Pump, API N11. . . . . . . . . . . . . . . . . 34 Q-Automatic Top Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Seating, Cup Type, Tubing Pump, API N13. . . . . . . . . . . . . . . 34 Q-Latch, On-Off Tool Assembly. . . . . . . . . . . . . . . . . . . . . . . . 46
Seating, Mechanical, Bottom Lock, API N12. . . . . . . . . . . . . 34
Seating, Mechanical, Top Lock, API N14 . . . . . . . . . . . . . . . . 35
Seating, Mechanical, Pacific Type Top or Bottom Lock. . . . . 35
Extension, Upper, API N21 . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Extension, Lower, N22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Strainer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Valves
Ball and Seat, API V11
NOTES:
1. When ordering, indicate complete part number by adding the following suffixes to Ball
only, Seat only, Assembly part number to indicate specific material:
C Tungsten Carbide, API material “A4”
NC Nickel Carbide, API material “A5”
S 440C Stainless Steel, API material “D1”
SN Silicon Nitride
TC Titanium Carbide, API material “A6”
W Wearloy, API material “A3”
2. For Ball & Seat Assembly, first suffix indicates seat material while second suffix indicates
ball material. If Ball and Seat are of the same material second suffix is blanked and just
indicate seat material.
www.Q2als.com | 1
Barrels
Hard Chrome Barrels
and designed to meet the latest edition of API 11AX specifications. Q2 Artificial Lift
Services’ chrome plating procedure provides a harder, smoother plated ID with more
corrosion resistance than previously available in the industry. This allows one to run our
barrels in more severe conditions compared to traditional chrome barrels.
Description
Chrome plated barrels are precision honed ID, chemically cleaned and pre-etched and
polished to meet specification. These barrels provide hardness up to 70 HRC with a
minimum thickness of 0.003” per side.
Our chrome plating process employs a proprietary high speed catalyst which provides
more uniform plating, high hardness, increases micro crack density and reduces porosity
from 25-50% to less than 15% than traditional chrome barrels. These factors provide
extended chrome life in abrasive conditions and protect against abrasion damage.
Solution chemistry and actual chrome plated samples are tested on a regular basis in
accordance to Q2 Artificial Lift Services’ strict quality management system to maintain
the highest quality product.
Products
Quality of preparation before chroming guarantees long shelf life of product& durability
in the ground.
Q-Chrome Barrels
Q2 ALS standard carbon steel chrome ID barrel is made from 1026 carbon steel and
meets latest edition of API 11AX Specification and NACE Standard MR0176 for A1
chrome plate on steel pump barrel material.
Barrels
Q2 ALS stainless steel chrome ID barrel is made from 501 stainless steel and
meets the latest edition of API 11AX specification and NACE standard MR0176 for
A3 chrome plate on 4/6 chrome steel pump barrel material. Q2 ALS stainless steel
barrels are higher in strength and excellent corrosion resistance as it contains
more chromium and recommended for severe abrasion, mild H2S and moderate
CO2 condition.
Duplex Chrome
Q2 ALS also offers duplex chrome plating on 1026 carbon steel, 443 admiralty
brass and 501 stainless steel materials. Duplex chrome provides even more
wearability and corrosion resistance with an increase in thickness from 0.003” to
0.006” per side.
Corrosion Resistance
Micro-crack and porosity are the two plating factors affecting corrosion resistance.
Micro crack density should high to reduce macro cracks and prevent cracks
extending through to the substrate. Metallography test results below show the
difference between Q2 ALS chrome plating Vs Traditional Chrome Plating.
Q2 ALS chrome plating: Micro-crack Traditional chrome plating: Macro- Traditional chrome plating: Large
density is so tight that they are barely cracks in the plating extend thru to porosity and micro-cracks decrease
visible. Porosity is well below 15%. the substrate allowing for accelerated corrosion resistance.
corrosion to occur.
www.Q2als.com | 3
Thin Wall, Rod Pump, API B11
Specifications
Barrels
Base Part
Pump Bore API Number
Number O.D. I.D. Thread
1-1/16” 15B(L) 1.312” 1.062” 1.1250-16 -
1-1/4” 15D(L) 1.500” 1.250” 1.3330-16 B11-125
1-1/2” 15F(L) 1.750” 1.500” 1.5730-16 B11-150
2” 15K(L) 2.250” 2.000” 2.0870-16 B11-200
2-1/2” 15N(L) 2.750” 2.500” 2.5730-16 B11-250
Barrels
Base Part
Pump Bore API Number
Number O.D. I.D. Thread
1-1/16” 16B(L) 1.625” 1.062” 1.5730-16 -
1-1/4” 16D(L) 1.625 1.250” 1.5730-16 B12-125
1-1/2” 16F(L) 1.875” 1.500” 1.8750-16 B12-150
1-3/4” 16H(L) 2.125” 1.750” 2.0870-16 B12-175
2-1/4” 16M(L) 2.750” 2.250” 2.5730-16 B12-225
NOTES:
1. When ordering, indicate complete part number by:
a. Specifying barrel length (L) in feet. API lengths are from 8ft through 30ft in 2ft increments only.
b. Adding the following prefixes to the base part number to indicate barrel material:
Blank Carbon Steel
B Brass
S Stainless Steel
c. Adding the following suffixes to the base part number to indicate ID condition:
Blank Non-Hardened or Non-Plated
C Single Chrome Plated (0.003” min. thickness with 67-70 HRC hardness)
CC Double Chrome Plated (0.006” min. thickness with 67-70HRC hardness)
H Induction Case Hardened (0.010” min depth with 58HRC min. hardness)
N Nickel Carbide Plated (0.115” min. thickness)
2. ID is precision honed and finished to +0.002”/-0.000” tolerance
www.Q2als.com | 5
Bushings
Seat, Barrel Cage, API B22
Bushings
Adapter, Barrel to Closed Cage, Slim Hole Pump
NOTES:
1. When ordering, indicate complete part number by adding the following prefixes to the base part number to
indicate specific bushing material:
Blank Carbon Steel, API material “A1” / “B1” M Monel, API material “A4”
A Alloy Steel, API material “A2” S Stainless Steel, API material “D6”
B Brass, API material “B5”
2. 24KN is 1” — to be used with top hold-down only.
www.Q2als.com | 7
Adapter, RH Barrel to RW Barrel, Gas Compressor Pump
Barrel Size Base Part Thread Size
O.D.
From To Number Upper Pin Lower Box
1-1/4” 1-1/2” 24DF-SP 1.875” 1.5730-16 1.5730-16
1-3/4” 2” 24HK-SP 2.250” 2.0870-16 2.0870-16
Bushings
NOTES:
1. When ordering, indicate complete part number by adding the following prefixes to the base part number to
indicate specific bushing material:
Blank Carbon Steel, API material “A1” / “B1” M Monel, API material “A4”
A Alloy Steel, API material “A2” S Stainless Steel, API material “D6”
B Brass, API material “B5”
Cages
O.D. API Number
Bore Number Number Upper S.R. Pin Lower Box
1-3/4” 12H 33H 1.688” 3/4” 1.4704-14 C11-20
33M 3/4” C11-25
2-1/4” 12M 2.188” 1.8024-14
33M1 7/8” -
33P 3/4” C11-30
2-3/4” 12P 2.625” 2.1095-11 1/2
33P1 7/8” -
33R 3/4” -
3-1/4” 12R 3.188” 2.8000-11 1/2
33R1 7/8” -
3-3/4” 12T 33T 3.625” 1” 3.1715-11 1/2 C11-40
5-1/2” 12ZA 33ZA 5.438” 1” 4.6250-8 -
4-3/4” 12ZB 33ZB 4.688” 1” 4.0000-10 -
7-3/4” 12ZF 33ZF 7.688” 1” 6.6250-8 -
www.Q2als.com | 9
Top Plunger, API C12
Cages
Closed, Barrel, One-Piece, Clutched, THOS Pump Only
NOTES:
1. When ordering, indicate complete part number by adding the following prefixes to the base part number to
indicate specific cage material:
Blank Carbon Steel, API material “A1” / “B1” M Monel, API material “A4”
A Alloy Steel, API material “A2” S Stainless Steel, API material “D6”
B Brass, API material “B5”
2. Add the suffix “-QS” to base part number to indicate hard lined cages. Available in Alloy or Stainless Steel only.
3. Balls & Seats listed are for reference only; see page 1 for complete part numbers and material availability.
www.Q2als.com | 11
Closed, Barrel, Insert Guided, 4-Piece, Insert Pump Only
Cages
Closed, Double Valve, Insert Guided, 4-Piece
NOTES:
1. When ordering, indicate complete part number by adding the following prefixes to the base part number to
indicate specific cage material:
Blank Carbon Steel, API material “A1” / “B1” M Monel, API material “A4”
A Alloy Steel, API material “A2” S Stainless Steel, API material “D6”
B Brass, API material “B5”
2. Add the suffix “-QS” to base part number to indicate hard lined cages. Available in Alloy or Stainless Steel only.
3. Washer material is Durometer 90 Viton.
4. Insert material is Cobalt Alloy.
5. Balls & Seats listed are for reference only; see page 1 for complete part numbers and material availability.
www.Q2als.com | 13
Closed, Pin End Plunger, One-Piece, API C13
Cages
Closed, Box End Plunger, Insert Guided, 4-Piece
NOTES:
1. When ordering, indicate complete part number by adding the following prefixes to the base part number to
indicate specific cage material:
Blank Carbon Steel, API material “A1” / “B1” M Monel, API material “A4”
A Alloy Steel, API material “A2” S Stainless Steel, API material “D6”
B Brass, API material “B5”
2. Add the suffix “-QS” to base part number to indicate hard lined cages. Available in Alloy or Stainless Steel only.
3. Washer material is Durometer 90 Viton.
4. Insert material is Cobalt Alloy.
5. Balls & Seats listed are for reference only; see page 1 for complete part numbers and material availability.
www.Q2als.com | 15
Closed, Barrel, Oversize Assembly
NOTES:
1. Housing and Insert materials are Alloy Steel.
2. Insert legs are hardened to 45-50 HRC
3. Balls & Seats listed are for reference only; see page 1 for complete part numbers and material availability.
4. Closed Barrel Cage Oversize assemblies adapts to 22-series Seat Barrel Cage Bushing. See specific parts
section for part numbers and material availability.
5. Closed Plunger Cage Oversize assemblies adapt to 98-series Seat Plugs or 106/109-series Pullers. See
specific parts section for part numbers and material availability.
Connectors
Base Part Box Thread Size
Pump Bore O.D. API Number
Number Top End Plunger End
1-3/4” 42H 1.688” 1.4704-14 1.5084-14 C22-175
2” 42K 1.938” 1.5604-14 1.7330-14 -
2-1/4” 42M 2.188” 1.8024-14 1.9864-14 C22-225
2-1/2” 42N 2.438” 2.1095-11 1/2 2.1095-11 1/2 -
2-3/4” 42P 2.650” 2.1095-11 1/2 2.3755-11 1/2 C22-275
3-1/4” 42R 3.188” 2.5625-11 1/2 2.5625-11 1/2 -
3-3/4” 42T 3.650” 3.1715-11 1/2 3.3825-11 1/2 C22-375
5-1/2” 42ZA 5.438” 4.6250-8 4.6250-8 -
4-3/4” 42ZB 4.688” 4.0000-10 4.2500-10 -
7-3/4” 42ZF 7.688” 6.6250-8 6.6250-8 -
NOTES:
1. When ordering, indicate complete part number by adding the following prefixes to the base part number to
indicate specific connector material:
Blank Carbon Steel, API material “A1” / “B1”
A Alloy Steel, API material “A2”
B Brass, API material “B5”
M Monel, API material “A4”
S Stainless Steel, API material “D6”
www.Q2als.com | 17
Upper Barrel, Oversize Tubing Pump
Couplings
3-3/4” 46T1 5.000” 3.844” 4.2380-11 1/2 4-1/2” LCSG-8RND -
4-3/4” 46ZB 6.050” 4.844” 5.2380-11 1/2 5-1/2” LCSG-8RND -
NOTES:
1. When ordering, indicate complete part number by adding the following prefixes to the base part number to
indicate specific connector/coupling material:
Blank Carbon Steel, API material “A1” / “B1” M Monel, API material “A4”
A Alloy Steel, API material “A2” S Stainless Steel, API material “D6”
B Brass, API material “B5”
www.Q2als.com | 19
Barrel, Lower, Soft-Packed Tubing Pump, API C36
Couplings
Pump Base Part Pull Tube Box Thread Size API
O.D.
Bore Number O.D. Plunger End Pull Tube End Number
NOTES:
1. When ordering, indicate complete part number by adding the following prefixes to the base part number to
indicate specific coupling material:
Blank Carbon Steel, API material “A1” / “B1” M Monel, API material “A4”
A Alloy Steel, API material “A2” S Stainless Steel, API material “D6”
B Brass, API material “B5”
www.Q2als.com | 21
Pull Tube, Lower, API C33
Couplings
Bottom Hold-Down, API S16
NOTES:
1. When ordering, indicate complete part number by adding the following prefixes to the base part number
to indicate specific coupling material:
Blank Carbon Steel, API material “A1” / “B1” M Monel, API material “A4”
A Alloy Steel, API material “A2” S Stainless Steel, API material “D6”
B Brass, API material “B5”
www.Q2als.com | 23
Sucker Rod and Polished Rod, Same Thread Ends
Nominal Size Type Part Number O.D. Length
5/8” Sucker Rod 54V 1.500” 4.000”
3/4” Sucker Rod 54W 1.625” 4.000”
3/4” Sucker Rod 54W1 1.500” 4.000”
3/4” Polished Rod PR54W 1.625” 4.000”
7/8” Sucker Rod 54X 1.812” 4.125”
7/8” Sucker Rod 54X1 1.625” 4.125”
7/8” Polished Rod PR54X 1.812” 4.000”
7/8” Polished Rod PR54X1 1.625” 4.125”
1” Sucker Rod 54Y1 2.000” 4.000”
1” Polished Rod PR54Y 2.188” 4.250”
1” Polished Rod PR54Y1 2.000” 4.250”
Couplings
Box to Pin
NOTES:
1. Material is Alloy Steel.
2. Sucker rod threads can be used with polished rod threads; polished rod threads cannot be used with sucker rod threads
www.Q2als.com | 25
Guides
Valve Rod, Box End, API G11
Guides
Tubing Base Part Pull Tube
Thread Size O.D.
Size Number Size A B C
71C101 15/16” 1.3330-16 1.875” 1.500” 0.812” 2.500”
2-3/8” 71E101 1-1/8” 1.625” 2.000”
1.5730-16 1.730” 0.750”
71E102 15/16” 1.500” 2.125”
71K101 1-1/8”
2-7/8” 2.0870-16 2.250” 2.000” 1.000” 2.250”
71K103 1-1/2”
NOTES:
1. When ordering, indicate complete part number by adding the following prefixes to the base part number
to indicate specific guide material:
Blank Carbon Steel, API material “A1” / “B1” M Monel, API material “A4”
A Alloy Steel, API material “A2” S Stainless Steel, API material “D6”
B Brass, API material “B5”
www.Q2als.com | 27
Hold-Down Assemblies
Seating, API Type, 3 Cup, Type “HR”, Rod Pump
Tubing Size 2-3/8” 2-7/8” 3-1/2”
No-Go 1.875” 2.337” 2.844”
I.D. 0.875” 1.188” 1.438”
Top 1.4704-14 1.8024-14 2.1095-11 1/2
Pin Thread Size
Bottom 1.1894-14 1.5604-14 2.0035-11 1/2
API Nipple I.D. 1.780” 2.280” 2.780”
No Req’d API Number Description Component Part Number
1 S11 Mandrel (A) 85K 85N 85Q
3 S12 Seating Cup (B) 625J+30 625M+70 625P+70
2 S13 Seating Ring (C) 110K 110N 110Q
1 S14 Lock Nut (D) 95K 95N 95Q
NOTES:
1. When ordering, indicate complete part number by adding the following prefixes to the base part number to indicate specific fittings material:
Blank Carbon Steel, API material “A1” / “B1” M Monel, API material “A4”
A Alloy Steel, API material “A2” S Stainless Steel, API material “D6”
B Brass, API material “B5”
2. Seating Cups listed are as per API-11AX specified cup sizes. See Seating Cups parts section for complete list of available material and cup size.
3. For 2-3/8” 5-Cup Hold-Down, spacer end (item B) is not needed. Seating Cup assembles to 87K mandrel directly.
4. Top Hold-Down assemblies adapt to 25-Series Bushings while Bottom Hold-Down assemblies adapt to 50-Series Couplings. See specific bushing/
coupling parts section for complete bushing and coupling part numbers and material availability.
5. These Hold-Downs are use with 89-series Seating Nipples. See 89-series Seating Nipple parts section for part numbers and material availability.
www.Q2als.com | 29
Seating, Metal Friction Ring Type, Insert Pump
Tubing Size 2-3/8” 2-7/8” 3-1/2” 4-1/2” 5” 5-1/2”
API Nipple I.D. 1.780” 2.280” 2.780” 3.795” 4.610” 6.180”
No-Go 1.875” 2.337” 2.844” 3.845” 4.674” 6.330”
Mandrel
I.D. 0.875” 1.188” 1.625” 2.250” 3.125” 4.250”
Pin Thread Top 1.4704-14 1.8024-14 2.1095-11 1/2 3.1715-11 1/2 3.6875-11 1/2 5.3750-8
Size Bottom 1.1894-14 1.5604-14 2.0035-11 1/2 2.8000-11 1/2 3.6875-11 1/2 5.3750-8
No Req’d Description Component Part Number
2-Ring Design
1 Mandrel (A) - 85N1 85Q1 85U1 85Z 85ZA1
2 Seating Cup (B) - 112N1-2.300 112P1-2.795 112U1-3.810 112Z1-4.625 112ZA1-6.190
2 Seating Ring (C) - 113N1 113P1 113U1 113Z1 113ZA1
1 Lock Nut (D) - 95N1 95Q1 95U1 95Z1 95ZA1
5-Ring Design
1 Mandrel (A) 85K3 85N1 85Q1 - - -
5 Seating Cup (B) 112K-1.800 112N-2.300 112P-2.795 - - -
5 Seating Ring (C) 113K 113N 113P - - -
1 Lock Nut (D) 95K1 95N1 95Q1 - - -
U-Ring Design
1 Mandrel (A) - - - 85U1 85Z -
2 Seating Cup (B) - - - 112U3-3.800 112Z3-4.615 -
1 Seating Ring (C) - - - 113U3 113Z3 -
1 Lock Nut (D) - - - 95U1 95Z1 -
Top Hold-Down assemblies adapt to 25-series Bushings while Bottom Hold-Down assemblies, adapt to 50-series Couplings.
See specific bushing/coupling parts section for complete bushing and coupling part numbers and material availability.
These Hold-Downs are used with 89-series Seating Nipples. See 89-series Seating Nipple parts section for complete part
numbers and material availability.
Hold-Downs
NOTES:
1. When ordering, indicate complete part number by adding the following prefixes to the base part number to indicate specific fittings material:
Blank Carbon Steel, API material “A1” / “B1” M Monel, API material “A4”
A Alloy Steel, API material “A2” S Stainless Steel, API material “D6”
B Brass, API material “B5”
2. Friction Rings material are only available in Brass and Stainless Steel. Use same prefixes as indicated above when ordering.
3. Friction Ring numbered suffix corresponds to Friction Ring O.D.
4. Seating Cups listed are as per API-11AX specified cup sizes. See Seating Cups parts section for complete list of available material and cup size.
www.Q2als.com | 31
Mechanical, API Type Top Lock, API S21
Tubing Size 2-3/8” 2-7/8” 3-1/2”
Pump RW 1-1/2” 2” 2-1/2”
Bore RH 1-1/4” 1-1/2” & 1-3/4” 2-1/4”
Thread Top Pin 1.4704-14 1.8024-14 2.1095-11 1/2
Size Bottom Pin 1.5730-16 2.0870-16 2.5730-16
I.D. 1.000” 1.250” 1.500”
API Number S21-20 S21-25 S21-30
No Req’d Description Component Part Number
1 Seat (A) 78K2 78N2 78Q2
1 Mandrel (B) 78K3 78N3 78Q3
1 Lock (C) 78K4 78N4 78Q4
1 Barrel Bushing (D) 78K6 78N6 78Q6
Mechanical Bottom Lock, API S21 Top Lock Converted to Bottom Lock
Tubing Size 2-3/8” 2-7/8” 3-1/2”
Thread Top Pin 1.4704-14 1.8024-14 2.1095-11 1/2
Size Bottom Pin 1” L.P. 1.-1/4” 1-1/2”
No Req’d Description Component Part Number
1 Top Bushing (A) 78K1 78N1 78Q1
1 Seat (B) 78K2 78N2 78Q2
1 Mandrel (C) 78K3 78N3 78Q3
1 Lock (D) 78K4 78N4 78Q4
1 Coupling (E) 78K5 78N5 78Q5
Hold-Downs
NOTES:
1. Seat material is Stainless Steel, hardened to 38-42 HRC.
2. Lock material is Alloy Steel, hardened to 41-45 HRC.
3. All other component parts are made of Carbon Steel.
4. These Hold-Downs are used with 96-series (API N14) Seating Nipples. See 96-series Seating Nipples
parts section for complete part number and material availability.
www.Q2als.com | 33
Nipples
Nipples
NOTES:
1. When ordering, indicate complete part number by adding the following prefixes to the base
part number to indicate specific nipple material:
Blank Carbon Steel, API material “A1” / “B1”
A Alloy Steel, API material “A2”
S Stainless Steel, API material “D6”
2. Seat material is Stainless Steel. Hardened to 38-42HRCTubing
www.Q2als.com | 35
Nipples
Strainer
Plugs
97D 15/16” 1.750” 1.000” 1.3330-16 P11-125-15
97F 1-1/8” 1.750” 1.188” 1.5730-16 P11-150-20
97F1 15/16” 1.750” 1.000” 1.5730-16 P11-125
97K 1-1/2” 2.000” 1.525” 2.0870-16 P11-200
97M 1-7/8” 2.750” 1.937” 2.5730-16 P11-225
Seat, Recessed
Base Part
Pump Bore Hex Size Thread Size
Number
1-1/16” 98B1 1/2” 0.8750-14
1-1/4” 98D1 9/16” 1.0000-14
1-1/2” 98F1 3/4” 1.2500-14
1-3/4” 98H1 7/8” 1.4704-14
2” 98K1 1” 1.5604-14
NOTES:
1. When ordering, indicate complete part number by adding the following prefixes to the base part number
to indicate specific plug material:
Blank Carbon Steel, API material “A1” / “B1” M Monel, API material “A4”
A Alloy Steel, API material “A2” S Stainless Steel, API material “D6”
B Brass, API material “B5”
www.Q2als.com | 37
Seat, API P12
Pump Bore Base Part Number O.D. Thread Size API Number
1-1/6” 98B 1.025” 0.8750-14 -
Plugs
NOTES:
1. When ordering, indicate complete part number by adding the following prefixes to the base part number to indicate specific
plug material:
Blank Carbon Steel, API material “A1” / “B1”
A Alloy Steel, API material “A2”
B Brass, API material “B5”
M Monel, API material “A4”
S Stainless Steel, API material “D6”
2. Friction Rings material are only available in Brass and Stainless Steel. Use same prefixes as indicated above when ordering.
Plungers
2-1/2” 100NQ(L) 100NW(L) 2.1095-11 1/2 -
2-3/4” 100PQ(L) 100PW(L) 2.3755-11 1/2 P23-275
3-1/4” 100RQ(L) 100RW(L) 2.5625-11 1/2 -
3-3/4” 100TQ(L) 100TW(L) 3.3825-11 1/2 P23-375
4-3/4” 100ZBQ(L) 100ZBW(L) 4.2500-10 -
5-1/2” 100ZAQ(L) 100ZAW(L) 4.6250-8 -
7-3/4” 100ZFQ(L) 100ZFW(L) 7.6250-8 -
NOTES:
1. When ordering, indicate complete part number by specifying:
• plunger length (L) in feet.
• clearance (FIT) in thousands of an inch (hundredths of millimeters).
• spray material as either Q-Hard (Q) or Tungsten Spray (W) for One-Piece and Monel Pin End Plungers.
2. When ordering Pressure Activated Plungers, indicate complete part number by adding the following suffix:
• 20 – for 20 rings; 40 – for 40 rings; 60 – for 60 rings
3. Spray metal thickness is 0.010” minimum.
4. Q-Spray Nickel Spray Hardness is 58 HRC minimum. Tungsten Spray Hardness is 65HRC average.
www.Q2als.com | 39
Rods
Valve, API R11
Rods
Pony (Pick – Up Sub)
Part Number - API Grade D Material
www.Q2als.com | 41
Seating Cups
Type “0”
Part Number
Tubing Size Cup Size Fit Size I.D.
Fiber Plastic
-.010” 626F-10 - -
1.500” +.030” - 626F+30 1.190”
1-1/2”
+.070” 626F+70 626F+70 -
1.750” +.070” 626H+70 - 1.440”
+.030” 626J+30 - -
2-3/8” 1.781”
+0.45” 626M+70 - 1.431”
+.70” 626M2+70 - 1.805”
2-7/8” 2.250” - 1.979”
-.010”
- 626P-10P -
3-1/2” 2.750” +.70” 626P+70 2.361”
Type “HR”
Tubes
18 (5.486) 207 (5.258) 206 (5.232) 204 (5.182)
19 (5.791) 219 (5.563) 218 (5.537) 216 (5.486)
20 (6.096) 231 (5.867) 230 (5.842) 228 (5.791)
21 (6.401) 243 (6.172) 242 (6.147) 240 (6.096)
22 (6.706) 255 (6.477) 254 (6.452) 252 (6.401)
23 (7.010) 267 (6.782) 266 (6.756) 264 (6.706) 1. When ordering, indicate complete part
24 (7.315) 279 (7.087) 278 (7.061) 276 (7.010) number by:
25 (7.620) 291 (7.391) 290 (7.366) 288 (7.315) • Specifying pull tube length (L) in whole
feet. See table.
26 (7.925) 303 (7.696) 302 (7.671) 300 (7.620) • Adding the following prefixes to base
27 (8.230) 315 (8.001) 314 (7.976) 312 (7.925) part number to indicate pull tube
28 (8.534) 327 (8.306) 326 (8.280) 324 (8.230) material:
Blank Carbon Steel, API material “N1”
29 (8.839) 339 (8.611) 338 (8.585) 336 (8.534) B Brass, API material “N5”
30 (9.144) 351 (8.915) 350 (8.890) 348 (8.839) M Monel, API material “N4”
www.Q2als.com | 43
Accessories
Q-Shear Tool, Woosley Type
SR Thread Size O.D. Part Number Shear Load in Pounds
80W14 14,000
80W17 17,000
80W20 20,000
3/4" 1.625” 80W22 22,000
80W26 26,000
80W30 30,000
80W33 33,000
80X22 22,000
1.813” 80X26 26,000
7/8”
80X30 30,000
1.625” 80X33-SH 33,000
80Y26 26,000
1” 2.000”
80Y33 33,000
1. Shear pins are W1 Tool Steel with 92 HRB minimum hardness.
2. All other component parts are made of Carbon Steel.
1. When ordering, indicate complete part number by adding the following prefixes to the Housing, Valve
Rod Guide and Housing Extension base part numbers to indicate specific material:
Blank Carbon Steel, API material “A1” / “B1” M Monel, API material “A4”
A Alloy Steel, API material “A2” S Stainless Steel, API material “D6”
B Brass, API material “B5”
2. Seat material is 440C Stainless Steel
3. See Bushing and Hold Down parts section for complete part number and material availability.
www.Q2als.com | 45
Q-Latch, On-Off Tool Assembly
Tubing Size 2-3/8” 2-7/8” 3-1/2” 4-1/2”
Tool OD 1.625” 1.812” 2.312” 2.740”
Sucker Rod Size 3/4” 3/4” 7/8” 7/8” 1” 1”
Ball O.D. 5/8” 11/16” 13/16” 1-1/16”
RH 160KW-BM 160NW-BM 160NX-BM 160QX-BM 160QY-BM 160UY-BM
Assembly Number
LH 160KW-LH-BM 160NW-LH-BM 160NX-LH-BM 160QX-LH-BM 160QY-LH-BM 160UY-LH-BM
No
Description Component Part Number
Req’d
1 Top Bushing 160KW1-BM 160NW1-BM 160NX1-BM 160QX1-BM 160QY1-BM 160UY1-BM
1 Spring 160N2 160N2 160N2 160Q2 160Q2 160Q2
1 Back-up Spring - - - 160Q2B 160Q2B 160Q2B
2 Guide Ball 10BS 10DS2 10DS2 10FS1 10FS1 10HS1
RH 160K4-BM 160N4-BM 160N4-BM 160Q4-BM 160Q4-BM 160U4-BM
1 Follower
LH 160K4-LH-BM 160N4-LH-BM 160N4-LH-BM 160Q4-LH-BM 160Q4-LH-BM 160U4-LH-BM
1 Body 160K3-BM 160N3-BM 160N3-BM 160Q3-BM 160Q3-BM 160U3-BM
1 Lock 160KW5-BM 160NW5-BM 160NX5-BM 160QX5-BM 160QY5-BM 160UY5-BM
1. Top Bushing material is Alloy Steel
2. S pring materials are Inconel X-750.
3. Body and Lock materials are Alloy Steel with TriniteTM heat trated surface.
4. Follower material is hardened Carbon Steel.
Accessories