183-05090-00 OTN Tunable SFP+ 10Gb With EFEC 120km EZ - Product Datasheet 1019
183-05090-00 OTN Tunable SFP+ 10Gb With EFEC 120km EZ - Product Datasheet 1019
183-05090-00 OTN Tunable SFP+ 10Gb With EFEC 120km EZ - Product Datasheet 1019
183-05090-00
Transceiver Optical Specifications (G.709 and FEC Enabled)
Parameter Symbol Min Typical Max Units
9.9533 (SONET/SDH)
Host Native Nominal Bit Rate
10.3125 (LAN PHY) Gbps
10.7092 (OTU2)
DWDM Line Interface Bit Rate Gbps
11.0957 (OTU2e LAN PHY)
+/- 20 (SONET)
OTN Interface Bit Rate Deviation ppm
+/- 100 (LAN PHY)
DWDM Frequency Range (Ch 59, 59.5, 60,
λWDM 195.9 - 196.05 THz
60.5)
Channel Spacing fSPACING 50 GHz
Laser Tuning Range fTUNE Full C-band
Wavelength Accuracy λEOL -25 - +25 pm
Extinction Ratio ER 6 - - dB
Side Mode Suppression Ratio SMSR 35 - - dB
Average Output Power POUT -1 - +3 dBm
Eye Mask Compliance GR-253i3/G.959.1
Receiver Operating Range @ 11.1Gbps
0 to 2000 ps/nm -29 -6 dBm
Rx Sensitivity @ 2000 ps/nm -29 dBm
Rx Power Warning/Alarm Level - -27/-29 dBm
183-05090-00
Compliance
SFF-8431 Rev 4.1 – SFP+ High Speed Electrical Interface
SFF-8472 Rev 11.3 – Diagnostics Monitoring Interface for Optical Transceivers
SFF-8690 Rev 1.4 – Tunable SFP+ Memory Map for ITU Frequencies
Class 1 Laser Safety
ROHS3 (10/10)
2
The following I C registers are used for the True Link feature:
Title
Page Reg Bit Type Description Settings
1 = Reset PRBS-31 error counter
R/W, PRBS-31 error counter reset (This bit is self clearing back to zero)
03h 183 7 SC (Self Clearing Bit) 0 = Normal operation.
03h 183 5:6 R/W Reserved
0 = PRBS-31 Rx pattern sync
present
03h 183 4 RO PRBS31 sync status 1 = PRBS-31 Rx pattern sync error
03h 183 2:3 R/W Reserved
PRBS31 1 = Enable PRBS31 payload read in
Control the Rx direction. If FEC enabled,
(Line Side) PRBS31 is error corrected. If FEC
is off, PRBS1 raw data is sent.
Enable PRBS31 pattern on 0 = Disable PRBS31 payload read
03h 183 1 R/W Rx Path in the Rx direction.
1 = Enable PRBS31 payload
insertion in the Tx direction. The Tx
direction PRBS data is inserted as
the payload data in the OTU2 frame.
Enable PRBS31 pattern on 0 = Disable PRBS31 payload
03h 183 0 R/W Tx Path insertion in the Rx direction.
Title
Page Reg Bit Type Description Settings
PRBS31 Error Counter (MSB-
03h 184 7:0 RO 32 bit counter) PRBS31 Error Count (MSB- 32 bit)
PRBS31 Error Counter (17 to PRBS31 Error Count (17 to 24 of 32
03h 185 7:0 RO PRBS31 24 of 32 bit counter) bit counter).
Checker
(Line Side) PRBS31 Error Counter (8 to PRBS31 Error Count (8 to 16 of 32
03h 186 7:0 RO 16 of 32 bit counter) bit counter)
PRBS31 Error Counter (LSB-
03h 187 7:0 RO 32 bit counter) PRBS31 Error Count (LSB- 32 bit).
183-05090-00
Link Checker Feature
The OTN SFP+ has the optional “Link Checker” feature, allowing the customer to proactively monitor the link performance
margin in real time locally or remotely. Link Checker provides proactive alarms to alert the customer of a link falling below a pre-
defined margin threshold, triggering an investigation of the optical layer to rectify the degradation before the customer takes
errors. The user monitors Laser Bias Current to verify the health or margin on the OTN wavelength. The Link Checker margin
can vary between 3 and 12, in which the higher the number the higher the margin. This is illustrated in the graph below.
As seen an OTN SFP+ DWDM channel with a Link Checker reading of 6 or higher is operating with a good operating margin.
Between 4 and 6 the link margin is low and may be the indicator of a link problem on the DWDM system. At 4 or below traffic is
affected or down on that link.
The link margin is supported through the reading of the FEC Correction Error Rate (FCER) in the SFP+ and displaying that
margin as the Laser Bias Current value on the router. The FEC correction error rate is averaged over a 25 second rolling
window by the module software. In the case of failure or no errors being corrected, the correction error rate is shown as 12.
The transposition of the correction error rate to laser bias current is shown below:
The FEC Correction BER can be represented as:
xx = Mantissa yy = Exponent
-6
For example, an error correction error rate of 3x10
where the Mantissa xx = 3 and the Exponent yy = 6
-6
Therefore a FEC Correction Error Rate (FCER) of 3x10 is shown as a Laser Bias current of 6.3 mA
Any error rate <10-5 will raise a Laser Bias Low Alarm in the system, which is an early warning indicator to the NOC to
proactively monitor and correct for a degraded link before errors are seen by the customer.
183-05090-00
OTN Alarm Register
This register is used to differentiate an LOS Alarm that is asserted due to a Loss of Signal versus an LOS Alarm that is asserted
to indicate an OTN Alarm. When LOS is asserted due to an OTN Alarm, the register value is set to 1. When LOS is asserted
due to loss of signal, the register value is set to 0.
Title
Page Reg Bit Type Description Settings
04h 133 7 RO OTN Alarm Register denoting OTN Alarm 0 = No OTN Alarm Present
1 = OTN Alarm Present
Laser Safety
OTN SFP+ is compliant to IEC 60825-1 laser safety. The DWDM laser output is specified as a Class 1 output power as defined
in IEC 60825-1, ed 2.0 2007.
CAUTION – Use of controls or adjustments or performance of procedures other than those specified herein may result in
hazardous radiation exposure.
183-05090-00
Host Connector Specifications
The SFP+ PCB host electrical connections are shown in the figure below.
183-05090-00
Physical Dimensions (mm)
183-05090-00
Wavelengths Supported
The following table provides correlation of the ITU-T DWDM wavelength and frequency as it relates to Menara Networks ID.
Frequency Wavelength Menara ID Frequency Wavelength Menara ID
196.05 1529.16 60.5 193.75 1547.32 37.5
196.00 1529.55 60 193.70 1547.72 37
195.95 1529.94 59.5 193.65 1548.11 36.5
195.90 1530.33 59 193.60 1548.51 36
195.85 1530.72 58.5 193.55 1548.91 35.5
195.80 1531.12 58 193.50 1549.32 35
195.75 1531.51 57.5 193.45 1549.72 34.5
195.70 1531.90 57 193.40 1550.12 34
195.65 1532.29 56.5 193.35 1550.52 33.5
195.60 1532.68 56 193.30 1550.92 33
195.55 1533.07 55.5 193.25 1551.32 32.5
195.50 1533.47 55 193.20 1551.72 32
195.45 1533.86 54.5 193.15 1552.12 31.5
195.40 1534.25 54 193.10 1552.52 31
195.35 1534.64 53.5 193.05 1552.93 30.5
195.30 1535.04 53 193.00 1553.33 30
195.25 1535.43 52.5 192.95 1553.73 29.5
195.20 1535.82 52 192.90 1554.13 29
195.15 1536.22 51.5 192.85 1554.54 28.5
195.10 1536.61 51 192.80 1554.94 28
195.05 1537.00 50.5 192.75 1555.34 27.5
195.00 1537.40 50 192.70 1555.75 27
194.95 1537.79 49.5 192.65 1556.15 26.5
194.90 1538.19 49 192.60 1556.55 26
194.85 1538.58 48.5 192.55 1556.96 25.5
194.80 1538.98 48 192.50 1557.36 25
194.75 1539.37 47.5 192.45 1557.77 24.5
194.70 1539.77 47 192.40 1558.17 24
194.65 1540.16 46.5 192.35 1558.58 23.5
194.60 1540.56 46 192.30 1558.98 23
194.55 1540.95 45.5 192.25 1559.39 22.5
194.50 1541.35 45 192.20 1559.79 22
194.45 1541.75 44.5 192.15 1560.20 21.5
194.40 1542.14 44 192.10 1560.61 21
194.35 1542.54 43.5 192.05 1561.01 20.5
194.30 1542.94 43 192.00 1561.42 20
194.25 1543.33 42.5 191.95 1561.83 19.5
194.20 1543.73 42 191.90 1562.23 19
194.15 1544.13 41.5 191.85 1562.64 18.5
194.10 1544.53 41 191.80 1563.05 18
194.05 1544.92 40.5 191.75 1563.45 17.5
194.00 1545.32 40 191.70 1563.86 17
193.95 1545.72 39.5 191.65 1564.27 16.5
193.90 1546.12 39 191.60 1564.68 16
193.85 1546.52 38.5 191.55 1565.09 15.5
193.80 1546.92 38 191.50 1565.50 15
183-05090-00
Ordering Guide
Part Number Feature Description
TEZ3ffrr- TNBL OTN SFP+, Full C-band Tunable, OTN OTU2 Integrated Framer with G.975 FEC,
Default FW Config, ITU-T Channel 16.0 Default Wavelength, APD Receiver, 9.9Gb/s
Host Speed
TEZ1ffrr-TNBL OTN SFP+, Full C-band Tunable, OTN OTU2e Integrated Framer with G.975 FEC,
Default FW Config, ITU-T Channel 16.0 Default Wavelength, APD Receiver,
10.3Gb/s Host Speed
The OTN SFP+ Tuning Cable and GUI part number is shown below.
Part Number Description
500006A-CBL OTN SFP+ Tuning Cable, OTN GUI software, wall mount power supply
menarainfo@menaranet.com
183-05090-00