Fisnar Catalogue 1

FRONT COVER
Engineered Dispensing Solutions
1
Contents
Dispensing Consumables
About Us Syringe Barrels, Pistons, Tip & End Caps 4-5
Barrel Adapters, Syringe Plungers & Sample Kits 6-7
Manual Syringes, Guns & Dispensing Bottles 8-9
Dispense Tips 10-16
Fisnar is a leading manufacturer and supplier of precision fluid dispensing Flow-Seal Pens and Bottles 17
and fluid handling solutions. Cartridges & Accessories 18-25
With over 30 years’ knowledge of the dispense industry and its regional Liquid Dispensers
requirements, we have an accomplished range of dispensing products
Digital Dispensers 26-27
including dispensing robots, dispensing valves, fluid dispensers and a Peristaltic Pump Dispenser 28-29
complete selection of dispensing consumables. Hand Held Dispensers 30-32
Dual Cartridge Dispenser 33
Vacuum Pick Up Dispensers 34-35
Armed with technical expertise and a diverse portfolio of dispensing Foot Controlled Dispenser 36
products, Fisnar can supply a dispensing system to suit every budget, Dispenser Pens 37
application, and industry.
OTHER SIDE OF FRONT COVER - About
Dispensing Valves
Fisnar products are available to purchase via our trusted network of global
Pinch Tube 38
distributors. Diaphragm 39
Needle 40
Visit our website: www.fisnar.com Cartridge 41
Spray 42
Poppet 43-44
Mini Spool 45
High Volume 46
Auger 47
Rotary 48
Positive Displacement 49
Valve Controllers 50-53
Contact Details
Reservoirs & Pumps
Europe Your Local Fisnar Distributor:
Reservoir Tanks 54-55
Clear View Pressure Chamber 56
infoeurope@fisnar.com Extruder Systems 57-59
+44 (0) 1355 577222 Pump Systems 60-61
Dispensing Stands 62
Accessories & Fittings 63
Asia CONTACT DETAILS
info@fisnar.com.hk Robotics
852-2389-2827 Robotics Overview 64
Gantry Robots 65, 71
Benchtop Robots 66 - 67
USA Vision System Robots 68-69
Cantilever Robot 70
SCARA Robot 72
info@fisnar.com Robot Accessories 73 - 80
(973) 646-5044
2 3
3.
QuantX™ - Premium Dispense Management System
QuantX™ is a fluid management system Evenpress™ Piston Selection
defined by its carefully designed and
precisely engineered components. Smooth flow green pistons prevent air entrapment and material waste by wiping the
Together these components provide a syringe barrel wall clean.
superior industrial dispensing experience,
Flat blue wall pistons are recommended for reducing potential stringing and bouncing
resulting in reduced waste, greater accuracy
when dispensing high-viscosity fluids.
and improved yields.
Low viscosity orange pistons are used for preventing dripping of watery fluids and accidental
QuantX™ Syringe Barrels back-flow into the dispenser.
QuantX™ syringe barrels feature a highly Soft black rubber pistons are used to prevent tunnelling in high viscosity fluid materials.
accurate manufacturing process that
combines minimal resistance and ultra Smooth Flat Low Lubricated Unlubricated
parallel uniformity over the length of the Size Flow Wall Viscosity Rubber Rubber
syringe barrel. Green Blue Orange Black Black
3cc 8001006 8001010 8001506 8001514 8001510
Manufactured from premium grade, silicone-free, polypropylene, these syringe barrels are 5cc 8001007 8001011 8001507 8001515 8001511
available in Clear for non UV materials, amber for UV protection (240-255nm) and opaque 10cc 8001008 8001012 8001508 8001516 8001512
black for maximum light protection. 30cc/ 8001009 8001013 8001509 8001517 8001513
55cc
I.D. O.D. Length
Size Base Clear Amber Black
(inch) (inch) (inch)
3cc Round 8001001 8001040 8001045 0.379 0.453 2.941 QuantX™ Syringe Barrel Tip Caps
5cc Round 8001002 8001041 8001046 0.500 0.567 2.756
10cc Round 8001003 8001042 8001047 0.622 0.733 3.567
Flat-base tip caps provide an air tight seal allowing you to pre-fill syringe barrels.
30cc Round 8001004 8001043 8001048 0.891 1.000 4.634
55cc Round 8001005 8001044 8001049 0.891 1.020 6.898 Base Tip Cap Colour
Flat 8001038 Green
QuantX™ Syringe Barrel and Piston Sets Pointed 8001039 Green
Syringe barrel and piston sets ensure that matched QuantX™ components
nents
are always used in the QuantX™ fluid management system providing
viding QuantX™ Syringe Barrel End Caps
optimum dispensing performance. Green polyethylene clip style quick-twist end caps ensure an air tight seal and secure the
neck opening of the syringe barrel when not in use or in storage.
Size Clear Amber Black
3cc 8001058 8001063 8001068 Size Product Code
5cc 8001059 8001064 8001069 3cc 8001034
10cc 8001060 8001065 8001070 5cc 8001035
30cc 8001061 8001066 8001071 10cc 8001036
55cc 8001062 8001067 8001072 30/55cc 8001037
4. www.fisnar.com info@fisnar.com 5.
QuantX™ - Premium Dispense Management System
QuantX™ Syringe Barrel Adapters with 1/8” (3.175mm) Hose QK-CSK Syringe Barrel Sample Kits
QuantX™ syringe barrel adapter assemblies provide a The syringe barrel sample kits give you
convenient quick connect to the controller from the the option to try different size and colour
syringe barrel. They are available with two hose lengths variations before making a higher volume
and optional micron filter-traps to prevent entry of purchase.
fluids/odours into the controller.
The QK-CSK pictured includes all syringe
3ft 6ft 3ft (91cm) sizes, colours and adapter assemblies.
Size
(91cm) (152cm) Includes Filter
Hose 1/8” (3.175mm) OD Size Clear UV
Green adapter head, includes quick connector, safety clip 3 / 5 / 10cc QK-3510 QK-5410UV
3cc 8001014 8001018 8001050 30 / 55 cc QK-3055 QK-3055UV
5cc 8001015 8001019 8001051 ALL QK-CSK
10cc 8001016 8001020 8001052
30/55cc 8001017 8001021 8001053
QK-NSK Needle Selection Kit
QuantX™ Manual Syringe Plungers A small selection of our most popular tip
sizes in all available gauge sizes including
QuantX™ manual syringe plungers have been tapered, PTFE lined and flexible tips.
designed to offer users a clean, comfortable alternative
to conventional squeeze bottles and hypodermic Product Code Description
syringes. QK-NSK Needle Selection Kit
Using a hand dispenser, all medium to high viscosity

fluids can be dispensed including sealants, solder DCK800 Dispensing Component Kit
pastes, epoxies and grease.
The DCK800 dispensing component kit
Users can control fluid deposits to dispense easily and includes a selection of QuantX™ syringe
accurately – without drips or oozing – and dispensing Product Code Size barrels, pistons and caps, a selection of
can be tailored to each specific application. popular tip types and sizes, together with
QHP3 3cc a supply reference chart for new orders.
The ergonomic, and safety conscious design of these QHP5 5cc
syringe dispensers enables consistent fatigue free QHP10 10cc
Product Code Description
dispensing, and ensures that no potentially harmful QHP30 30cc
adhesives or sealants will contact the user’s skin. DCK800 Dispensing Component Kit
Manual Syringes PolySpense™ Dispensing Bottles
The manual syringes range includes the graduated Luer lock (LL) manual syringe barrel, LDPE squeeze type PolySpense™ low density
plunger and piston kit. bottle kits feature a unique Luer lock cap that
accommodates all precision dispense tips.
This selection of disposable components work efficiently together to form a system to
manually dispense fluids ranging from low to high viscosities. Available in 3/4, 1, 2 and 4 oz sizes, PolySpense™
needle-bottle kits are ideal for dispensing
Barrels are moulded with polypropylene and include Luer lock style connectors with alcohols, cleaning agents, flux, cyanoacrylates,
stopper, lubricated rubber piston and plunger. adhesives, solder mask, and other materials.
This selection of dispense bottle kits suits all

Product applications as end users can select their ideal
Size Description
Code dispense tip from the complete dispense tip
8401006 3cc Graduated LL Syringe Barrel Kit range.
8401007 5cc Graduated LL Syringe Barrel Kit
8401008 10cc Graduated LL Syringe Barrel Kit Dispense bottle kits include LDPE bottle and cap
8401009 30cc Graduated LL Syringe Barrel Kit seal with Luer lock thread.
8401012 60cc Graduated LL Syringe Barrel Kit
Dispensing tips are sold separately.
Features
JD927 Dispense Gun • Interchangeable, giving users the Product
Size Description
option to detach and change for Code
The JD927 is a lightweight and comfortable
replacement dispensing tips. 5606000 3/4 oz / PolySpense™ Bottle and
dispensing gun with easy twist-on barrel mounting.
21.3 ml LL Cap Set
• Good temperature threshold. 5606001 1 oz / PolySpense™ Bottle and
An effortless squeeze of the trigger advances the
28.41 ml LL Cap Set
plunger by 0.24” (6mm) dispensing an exact amount
5606002 2 oz / PolySpense™ Bottle and
of material every time. • Perfect for dispensing low viscosity
56.8 ml LL Cap Set
fluids.
5606003 4 oz / PolySpense™ Bottle and
JD927 is capable of dispensing most fluids by using 113.65 ml LL Cap Set
a finger tip control and push button plunger release • Smooth design for fluid flow and
to ensure liquid volume control. control.
Product • Silicone-free plastics.

Size Description
Code
JD927-10 10cc Dispense Gun • Soft low density plastic reduces
JD927 30cc Dispense Gun hand fatigue.
UV Epoxy Seal Dispense Tips Tapered Dispense Tips
An extensive selection of UV epoxy seal dispense Tapered dispensing tips are plastic tips designed
tips with moulded hubs and stainless steel to dispense medium to high viscosity materials.
needles.
These smooth flow dispense tips are moulded
To optimise dispensing results, these industrial with a Luer lock polypropylene hub and have a
performance precision tips are available in full uniform length that is flash free for consistent fluid
Luer lock thread for high viscosity materials and dispensing. Double tapered tips feature a unique
cost efficient ear type Luer lock fastening for low fluid outlet design to reduce fluid wicking.
viscose liquid dispensing.
I.D. I.D.
Angled dispense tips allow the operator Colour Gauge Standard Luer lock Double Tapered Luer lock
(inch) (mm)
to dispense in hard-to-reach areas that are
Olive 14 0.063 1.60 8001269
inaccessible with straight tips. Angled tips are
Orange 14 0.063 1.60 8001263
available in both 45° and 90° versions. Grey 16 0.047 1.20 8001270 8001264
Green 18 0.033 0.84 8001271 8001265
Pink 20 0.024 0.60 8001272 8001266
Blue 22 0.016 0.41 8001273 8001267
I.D. I.D. 1/4” 1/2” 1” 1.50” 45° 1/2” 90° 1/2” Red 24 0.014 0.37 8001268
Colour Gauge
(inch) (mm) (6.35mm) (12.7mm) (25.4mm) (38.1mm) (12.7mm) (12.7mm) Red 25 0.010 0.25 8001274
Olive 14 0.063 1.60 8001115 8001084 8001095 8001105 8001156 8001166 Clear 27 0.008 0.20 8001275
Amber 15 0.054 1.37 8001073 8001085 8001096 8001106 8001157 8001167 Lavender 30 0.0059 0.15 8001276
Black 16 0.047 1.20 8001074 8001086 8006031 8001495
Green 18 0.033 0.84 8001075 8001087 8001097 8001107 8001158 8001168
Pink 20 0.024 0.60 8001076 8001088 8001098 8001108 8001159 8001169
Purple
Blue
21
22
0.020 0.51 8001077 8001089
0.016 0.41 8001078 8001090
8001099
8001100
8001109
8001110
8001160
8001161
8001170
8001171
UV Light Block Dispense Tips
Orange 23 0.013 0.33 8001079 8001091 8001101 8001111 8001162 8001172
Red 25 0.010 0.25 8001080 8001092 8001102 8001112 8001163 8001173 Used for dispensing medium to high viscosity fluids while blocking all UV and light
Beige 26 0.009 0.23 8001463 emitting rays.
Clear 27 0.008 0.20 8001081 8001093 8001103 8001113 8001164 8001174
Lavender 30 0.006 0.15 8001082 8001094 8001104 8001114 8001165 8001175 Colour Gauge I.D. (inch) I.D. (mm) Product Code
Yellow 32 0.004 0.10 8001083 8001117
Light Green 33 0.004 0.10 8001116 Black 14 0.063 1.60 8001278
Black 16 0.047 1.20 5601281
Black 18 0.033 0.84 5601282
Black 20 0.023 0.58 5601283
Black 22 0.016 0.41 5601284
Black 25 0.010 0.25 8001279
Black 27 0.008 0.20 8001272

Flexible Tips Crimp Seal Dispense Tips
Flexible tips consist of polypropylene colour coded tips for dispensing in hard-to-reach Straight blunt end, crimp seal cannula dispense tips are constructed with a stainless steel
areas and are suitable for cyanoacrylates. straight cannula crimp, sealed to a polypropylene hub with “ear-type” Luer lock fastening.
Available in 1/2” and 1.5” sizes, these tips are used to prevent scratching or damage to fragile These tips are polished with a burr-free finish for smooth fluid dispensing and sold as 1/2”
dispense surfaces. (12.7mm) or 1” (25.4mm) lengths.
I.D. I.D. 1/2” 1.5” I.D. I.D. 1/2”

Colour Gauge Colour Gauge
(inch) (mm) (12.7mm) (38.1mm) (inch) (mm) (12.7mm)
Olive 14 0.063 1.60 8001285 8001291 Aluminium 14 0.063 1.60 8001196

Am b er 15 0.054 1.37 8001286 8001292 Da r k Gr een 14 0.063 1.60 8001197
Green 18 0.033 0.84 8001287 8001293 Aluminium 15 0.054 1.37 8001198
Pink 20 0.024 0.60 8001288 8001294 Green 18 0.033 0.84 8001199
Blue 22 0.016 0.41 8001289 8001295 Brown 19 0.027 0.69 8001200
Red 25 0.010 0.25 8001290 8001296 Pink 20 0.024 0.60 8001201
Purple 21 0.020 0.51 8001202
Blue 22 0.016 0.41 8001203
Orange 23 0.013 0.33 8001204
Red 25 0.010 0.25 8001205
PTFE Lined Dispense Tips Beige
Lavender
26
30
0.009
0.006
0.22
0.15
8001206
8001208
Stainless steel cannulas with an internal PTFE fitted projecting approximately 1/8" (3.18mm)
from the cannula. Ideal for dispensing very low viscosity fluids, solvents and cyanoacrylates.
I.D. I.D.
Colour Gauge 1” (25.4mm)
(inch) (mm)
I.D. I.D. 1/2” 1" Aluminium 14 0.063 1.60 8001209

Colour Aluminium 15 0.054 1.37 8001210
(inch) (mm) (12.7mm) (25.4mm)
Pink 18 0.033 0.84 8001211
Grey 0.023 0.58 8001252 8001254 Brown 19 0.027 0.69 8001212
Pink 0.006 0.15 8001253 8001255 Yellow 20 0.024 0.60 8001213
Green 21 0.020 0.51 8001214
Black 22 0.016 0.41 8001215
Light Blue 23 0.013 0.33 8001216

Micron-S Dispense Tips Dispensing Brush Tips
Micron-S precision nozzles offer high accuracy An enhanced range of silicone free dispensing brush tips designed for 'spreading' of greases
micro-dot dispensing due to their super low and other fluid materials to suit you application requirements.
resistance molecular fluid flow.
This diverse range of industrial grade brush and flow sizes, allows users to easily control the
These precision machined nozzles, have been coverage of fluid to substrate, as well as the speed of the fluid flow through the tip.
specifically designed to improve flow rates and
overall performance.
Product Code Gauge Dimensions
The thin rigid wall conical design is guaranteed
BT2102R 21ga 2mm Round
to enhance the accuracy and definition of dots,
lines or special patterns while at the same
time dramatically reducing fluid stringing or
tailing tendencies. Entecoat versions reduce BT2105R 21ga 5mm Round
fluid wicking and dripping. Compatible with BT2705R 27ga 5mm Round
anaerobic fluids. BT1410F 14ga 10mm Flat
BT2110F 21ga 10mm Flat
Gauge I.D. I.D. O.D. O.D. BT2710F 27ga 10mm Flat
Colour Standard Entecoat
/ Exit (inch) (mm) (inch) (mm) 5601309 15ga 3mm Round
Pink 18 0.041 1.041 0.049 1.254 5901001 5901012
5601310 15ga 3mm Round
Tan 19 0.034 0.864 0.042 1.067 5901002 5901013
Green 20 0.027 0.686 0.035 0.889 5901003 5901014
Light B lue 21 0.024 0.609 0.032 0.813 5901004 5901015
Purple 23 0.022 0.564 0.025 0.635 5901005 5901016
White 25 0.017 0.437 0.020 0.508 5901006 A brush tip selection kit is also available for this range and contains:
Red 27 0.013 0.335 0.016 0.406 5901007
Black 30 0.009 0.233 0.012 0.305 5901008
Blue 150μm 0.006 0.16 0.010 0.24 5901009 1 x 21 ga 2mm Round Tip
Orange 100μm 0.004 0.11 0.008 0.20 5901010 1 x 27 ga 2mm Round Tip
Yellow
50μm 0.002 0.006 0.006 0.16 5901011
1 x 14 ga 5mm Round Tip
A tip selection kit is available for this range containing each
of the standard bore nozzles. 1 x 14 ga 10mm Flat Tip
1 x 21 ga 10mm Flat Tip
Product Code: 5901000. 1 x 27 ga 10mm Flat Tip
Product Code: BT-SEL-KIT

Stainless Steel Dispense Tips Flow-Seal Pens and Bottles
Product Cannula Gauge I.D. I.D. Length Flow-Seal environmental pens and bottles
Code Type (inch) (mm) (mm) channel controlled amounts of no-clean flux,
5601238 Single 13 0.071 1.80 15 RMA, solvents, lubricants, masking and water-
5601239 Single 14 0.0063 1.60 15 based liquids. Flow-Seal products prevent
5601240 Single 15 0.054 1.37 15 evaporation of material and conform to current
5601241 Single 16 0.047 1.20 15 regulations for controlling substances capable of
5601242 Single 17 0.042 1.06 15 evaporation hazard.
5601243 Single 18 0.033 1.20 15
5601244 Single 19 0.034 0.864 15
The pen or bottle is supplied in two parts (cap and
reservoir) and is easily assembled. The reservoir,
5601245 Single 20 0.024 0.60 15
should be filled with material within 0.75” (19mm)
5601246 Single 21 0.024 0.609 15
of the top; this air chamber allows for the valve
Stainless steel dispensing tips are 5601247 Single 22 0.016 0.41 15
cap to be pressed securely in position.
available in one or two cannula 5601248 Single 22 0.016 0.41 15
combinations for fine deposition. 5601249 Single 23 0.022 0.564 15
This unique dispensing valve prevents flooding Features
5601250 Single 24 0.014 0.37 15 and spattering, releasing material in controlled
Precision stainless steel dispensing tips 5601251 Single 25 0.010 0.25 15 amounts to the tip. • Flow-Seal products are supplied
are internally machined for guaranteed 5601252 Single 26 0.009 0.23 15 with nib 381-8425-AC.
smooth flow liquid dispensing. 5601253 Single 27 0.008 0.20 15 Product
Description
8601254 Single 28 0.007 0.18 15 Code • Priming is achieved by depressing
8601255 Single 30 0.006 0.15 15 FV-0100 Flow-Seal Pen (10ml) the tip while the pen is vertical.
Each stainless steel tip consists of 5601323 Twin 16 0.047 1.20 20 Clear
a precision stainless steel hub and 5601324 Twin 17 0.039 1.00 20 FV-0200 Flow-Seal Pen ESD Safe (10ml) • The Flow-Seal cap allows for easy
cannula with a threaded Luer lock, 5601325 Twin 18 0.031 0.80 20 Aluminium removal of a choice of tips when
which prevents the tips from loosening 5601326 Twin 19 0.026 0.65 20 FV-0300 Flow-Seal Bottle 2oz (59.14ml) cleaning or replacing and creates
in the barrel and falling off. Clear a secondary mini reservoir to hold
5601327 Twin 20 0.024 0.60 20
FV-0400 Flow-Seal Bottle 2oz (59.14ml) the fluid.
5601328 Twin 21 0.020 0.50 20
This range of tips can be sterilised by Aluminium
5601329 Twin 22 0.016 0.40 20
an autoclave process for applications FV-0500 Flow-Seal Bottle 4oz (118.21ml) Clear • Standard reservoir and open top
5601330 Twin 23 0.012 0.30 20
requiring sterile equipment. FV-0600 Flow-Seal Jumbo Pen (10ml) bottles allow fluids to evaporate in
5601331 Twin 24 0.011 0.28 20 Black the working area.
5601332 Twin 26 0.010 0.25 20 381-8425-AC Nib acrylic chisel
Custom sizes available upon special
request. 5601333 Twin 27 0.008 0.20 20 381-8425-AB Nib acrylic bullet • Flow-Seal pens are cost efficient
381-8425-AP Nib acrylic point as product is only delivered when
381-8425-PC Nib polyester chisel required.
381-8425-PB Polyester bullet nip
381-600-PB Polyester blunt tip - FV0600 only

Cartridges Plungers
This range of high quality disposable cartridges and nozzles Plungers assist in the prevention of tunnelling with viscose fluids and provide even pressure.
provide a clean, efficient and low-cost method to meet all
types of production requirements. Caps and plugs for both
ends of the cartridge are available, as well as plungers with Product
Description Colour
a wiper leading edge to allow each cartridge to be cleaned Code
thoroughly. 5601354 2.5, 6, 8, 12 oz. wiper, LDPE Blue
5601355 1/10th gallon wiper, LDPE White
A system ideal for use in a wide range of applications including 5601356 20 oz. wiper, LDPE Natural
pre-mixed and frozen product handling as well as for use with 5601439 2.5, 6, 8, 12 oz UV blocking Black
pre-packaged materials. wiper, LDPE
5601440 1/10th gallon UV blocking Black
Cartridges can be used with hand held or bench mounted air wiper, LDPE
powered dispensing tools or manual dispensing tools.
Cartridge Caps
Length Diameter Capacity
(inch / mm) (inch / mm) (ml /oz) Top flange caps seal the wide brim of the cartridge and bottom caps seal the dispensing or
5601358 Natural LDPE 4.00/101.60 1.59/40.40 74/2.5 tip end of the cartridge.
5601364 Natural HDPE 4.00/101.60 1.59/40.40 74/2.5
5601359 Natural LDPE 7.11/180.60 1.59/40.40 177/6 Product
5601365 Natural HDPE 7.11/180.60 1.59/40.40 177/6 Description Colour
Code
5601371 Black HDPE 7.11/180.60 1.59/40.40 177/6 5601383 2.5, 6, 8, 12 oz. flange cap, Red
5601360 Natural LDPE 8.92/226.50 1.59/40.40 237/8 LDPE
5601366 Natural HDPE 8.92/226.50 1.59/40.40 237/8 5601384 1/10th gallon flange cap, Red
5601361 Natural LDPE 12.34/313.40 1.59/40.40 355/12 LDPE
5601367 Natural HDPE 12.34/313.40 1.59/40.40 355/12 5601385 20 oz. flange cap, LDPE Red
5601373 Black HDPE 12.34/313.40 1.56/40.40 355/12 5601386 Threaded tri seal tip cap, PE Red
5601362 Natural LDPE 8.99/228.30 1.85/47.00 325/1/10th Gal 5601387 Snap on tri seal tip cap, PE Red
5601368 Natural HDPE 8.99/228.30 1.85/47.00 325/1/10th Gal 5601388 Threaded tip cap, PE Red
5601369 Natural HDPE 10.03/254.80 2.57/65.30 591/20 5601389 Push on red tip cap, PE Red
5601375 Black HDPE 10.03/254.80 2.57/65.30 591/20 5601441 Threaded tip cap UV Black
blocking, LDPE

Metal Cartridge Retainers CR300 Cartridge Retainers
Heavy duty, light weight retainers which can withstand up to 100psi (6.9bar) pressure. CR300 cartridge dispenser has been
Cartridge retainers accommodate all cartridges. Retainer cap sold separately. developed with a new seal design,
guaranteeing greater seal performance
and durability by sealing directly onto the
inside of the ‘inserted’ cartridge.
5601379 74ml / 2.5 oz Cartridge Retainer
5601380 177ml / 6 oz Cartridge Retainer Fully compatible with 1/10th gallon
cartridges and both plastic and metal
5601381 237 ml / 8 oz Cartridge Retainer
caulking type cartridges (300/310ml), this
5601382 355ml / 12oz Cartridge Retainer high-grade anodised alloy retainer and cap
5601417 591 ml / 20 oz Cartridge Retainer
ensures a safe and comfortable dispensing
*Requires 5601418 pressure of up to 100psi (6.9Bar).
5601418 An adapter required for
a 20 oz retainer The high performance CR300 is incredibly
versatile and can be used as a pressurised
fluid reservoir system when used in
conjunction with a Fisnar dispense valve.
Retainer Cap Features:

Retainer caps provide a secure lock of the cartridge and metal retainer. Supplied with a • Supplied with a universal air-inlet • An optimised tube design reducing
female quick connect and sealing ring. Maximum pressure 100psi (6.9bar). for effortless system installation and cartridge expansion whilst decreasing
integration. the risk of air ingression into the fluid.
• Designed for long lasting use. • Works efficiently with 1/10th gallon
cartridge adapter nuts to convert the
• Equipped with a quick and easy screw male thread on a standard caulking
Product Code Description on cap and can be attached directly to type cartridge to a conventional female
5601376 Retainer cap with seal ring a Fisnar air-powered dispenser. 1/4” NPT thread.
5601377 Retainer cap with regulator gauge

5601378 Sealing ring only Product Code Description
5601429 Retainer cap for 5601418 CR300 Cartridge Retainer

CR300-Seal Retainer cap sealing ring

Cartridge Tip Adapters Dispensing Nozzles
Cartridge Tip Adapters convert the fluid outlet on a Nozzles provide a wide range of application capabilities. Standard nozzles may be cut back to
cartridge to a Luer lock connection for use with Fisnar increase orifice size. Tip adapters have standard 1/4" NPT male threads to fit all cartridges or
dispense tips by a 1/4 inch NPT. equivalent and standard male Luer lock threads on opposite side to fit all Luer lock dispensing tips.

Standard Nozzles
5601390 Tip Adapter White Polypropylene
Standard nozzles are precision moulded from natural
5601449 Tip Adapter Black Polypropylene polyethylene and have 1/4" NPT male threads to fit all
5601420 Tip Adapter Metal cartridges or equivalent.
Length Ofrice Size Material

Product Code
(inch / mm) (inch/mm)
Connecting Hose 5601391 2 / 63.5 1/16 / 1.59 HDPE
5601394 4 / 101.6 1/16 / 1.59 HDPE
A 6ft (180cm) hose to connect a retainer cap and 5601396 4 / 101.6 1/8 / 3.18 HDPE
dispenser. Includes a quick connect coupling at 5601398 4 / 101.6 1/32 / 0.79 LDPE
each end. 5601399 4 / 101.6 3/32 / 2.38 HDPE

5601357 Cartridge Retainer Specialty Nozzles
Connecting hose
562146 CR300 Connecting hose with Specialty nozzles are precision moulded from Polyethylene and have 1/4" NPT male threads to fit
metal quick connect all cartridges or equivalent.
Available in various widths and thickness to meet a special application.

Cartridge Adapter Nut Length Ofrice Size Nozzle Style
Product Code
Cartridge adapter nuts are used for converting the male (inch / mm) (inch/mm)
thread on a 310ml / 1/10th gallon cartridge to a 1/4" NPT 5601404 4 / 101.6 1/2 x 1/16 Spreader
female thread. This will then allow 1/4" nozzles or fittings 12.7 / 1.59
to be directly fitted and used; or have a tip adapter nut 5601405 4 / 101.6 1/2 x 1/16 45° Spreader
(5601449) fitted to attached Luer lock dispense tips for 12.7 x 1.59
dispensing directly from the cartridge. 5601406 4.5 / 114.3 3/4 x 1/8 Spreader
19.05 x 3.18
Product Code Description 5601407 4.4 / 111.76 1 x 1/8 Spreader
561129-SS 316 Stainless Steel 25.4 x 3.18
5601408 4 / 101.6 1 3/4 x 1/8 Spreader
561129 White Acetal 44.45 x 3.18

580091H-A Plastic Retainer and Cap Automatic Barrel Loaders
The 580091H-A is used to dispense directly from An efficient method of transferring grease, epoxy,
standard caulking cartridges without mess or silicone, solder paste and other thixotropic
waste. The retainer containing the cartridge materials into a disposable barrel.
is sealed with a cap connected to a DSP501N
dispenser (optional) to provide a timed shot The barrel loaders can be connected to a DSP501N
without post extrusion. Dispensing can be dispenser (optional) to control the operation.
delivered with fine gauge Luer lock tips or with
larger nozzles. Dispensing pressure should not The 560022 barrel loader is ideal for pre-filled 12
exceed 65psi (4.48 bar). An adapter is available for Product Code Description oz cartridges, which are placed inside a vertical
non-removable nozzles. 1/10th gallon cartridges 580091H-A Plastic retainer and cap container mounted on the stand.
and accessories are also available for use with the 1/10th gallon
580091H-A. The barrel attachment assembly is threaded to
accept Luer lock barrels.
560548-M Manual Barrel Loader Activating the DSP501A causes the material to rise
inside the barrel. This method simplifies loading
and reduces the possibility of entrapped air in the
The 560548-M manual barrel loader loads a barrel fluid.
directly from a 1/10th gallon caulking tube.
The 560022 includes stand, retainer support, 12
The barrel loader is connected to an air regulator oz retainer and cope, one empty 12 oz cartridge
and set to a pressure suitable for the material but and plunger, an outlet cap and special barrel
less than 65psi (4.48 bar). attachment assembly. Product Code Description
560022 Cartridge Barrel Loader
A switch on the side of the stand activates the air The model 560548 1/10th gallon barrel loader
flow and is switched off when the material reaches also uses the DSP501A. 560548 1/10th Gallon
the desired level. Barrel Loader
Includes replacement parts: 560546 1/10th Gallon
The barrel attachment assembly is threaded to
Nozzle Adapter
accept Luer lock barrels. • 5601367 12 oz cartridge
• 5601354 Plunger DSP501N Dispenser 110/220V CE
Includes replacement parts: • 912 Bushing
• 913 Male connector 1/4" NPT, 3/8" tube
Product Code Description • 561105 1/4" NPT street elbow • 914 Elbow 1/4" NPT, 3/8" tube
560548-M Manual Barrel Loader
• 560733 1/4" 28 UNF Luer lock connector • 915 Flexible tube, 3/8" O.D.
1/10th Gallon • 560734 1/4" 28 UNF 1/4" MPT educer • 560710 Luer lock cap
• 560710 Luer lock cap

SL101N Digital Dispenser DC100 Precision Dispenser
An automatic digital dispenser with a The DC100 digital dispenser has a versatile
bright LCD display and “teach and learn” design, which ensures it is perfectly
process programming. suited for a wide variety of dispensing
applications: from microdot deposits,
Up to 9 independent dispensing programs lines to large potting and filling.
may be stored for fast recall.
This advancement in dispensing
The SL101N has three modes of operation: technology allows the user more control
over their dispensing applications.
Autocycling mode
Alarms can be set to notify the user when material life has ended or fluctuations in dispensing
Combines a dispense time and pause time and will continue to repeat the cycle until foot
pressure have occurred.
pedal is actuated.
The user friendly programming allows for up to 10 programs to be saved and 5 different
Manual-mode dispensing modes to be used.
The dispense operation is manually controlled by a foot pedal.
Timed mode Features: Specifications:

Dispenses at a pre-set time.
• Adjustable air output and vacuum Product Code: DC100
Features: Specifications: with digital display. Cycle rate: 600+ cycles per
minute
• Digitally controlled programming. Product Code: SL101N • Air input tolerance can be set for Timer: 0.008 to 9999
Dispense time: 0.01 - 99.99 seconds consistent pressure. seconds
• Wide range of applications. Programs: 10 memory slots
Cycle: Manual, Timed, Cycle
• Can be locked to keep programs from Input AC to power 100-240 VAC -
Internal memory: 9 save locations
• Barrel suck-back ensures no being modified. supply: 50/60Hz
dripping. Air input: 70 - 100psi
Output DC from power 24 VDC - 0.75 Amp
Air output: 1 - 100psi
• Auto purge to prevent premature supply:
• Stores up to 9 dispensing routines. Internal voltage: 24 VDC
curing of material. Air input: 100psi maximum
Voltage: 100-240 VAC
Air output: 0-100psi
• Can be used as a stand alone semi- Dimensions (WxDxH): 1/4” tube adapter • Dispense counter for tracking Operating temperature: 50-140° F
automated dispense system. Weight: 1.59 kg completed dispense cycles. Relative humidity: 20 - 90%
Standards: CE, RoHS Compliant
(no condensation)
Models Models Dimensions (WxDxH): 7.09” x 7.68” x 3.15”
Weight: 86 g
SL101 Digital Dispenser DC100 Precision Dispenser
Standards: CE Approved,
RoHS Compliant

PPD-130 Peristaltic Pump Dispenser PPD-130 Accessories
Peristaltic pump dispensers transfer low The PPD-130 has a range of accessories included
viscosity liquids by pressure displacement as well as a number of additional tubing, nozzles
applied to a turning rotor against a tube and optional pump heads.
carrying material.
Accessories included:
PPD-130 offers excellent features for air-
free positive displacement dispensing of • 562030-T Standard rotor for standard tubes
materials such as cyanoacrylate, solvent, • 560989-D Nozzle holder (with switch)
alkaline and acid. • 561010-D Nozzle 1.7mm diameter
• 561011-D Nozzle 2.1mm diameter
Dispense outputs can be timed from 0.01 - • 561012-D Nozzle 2.6mm diameter
99.99 seconds with flow speeds from 0.01 • 561013-D Nozzle 3.5mm diameter
- 6ml/min using silicone tubing. The pump • 560984P Hose 1ft (304.8mm) 1.0 x 1.6mm
is bidirectional allowing snuff-back after • 560985P Hose 1ft (304.8mm) 1.4 x 2.0mm
discharge to preventing dripping. • 560995P Hose 1ft (304.8mm) 1.9 x 2.5mm
• 560996A Hose 1ft (304.8mm) 2.4 x 3.0mm
Features: Specifications: • 562031-D 9-pin connector
• 562032-D Foot pedal (optional, not included)
• Forward and reverse motion. Product Code: PPD-130
Cycle rate: 0.01 - 99.99
• Adjustable interval before reverse
direction.
seconds Tubing, Nozzles & Optional Pump Heads
Flow speed
PTFE tube: 0.01 - 6ml/min
• Continuous or timer modes. I.D x O.D Suitable Nozzle Type Nozzle
Silicone tube: 0.1 - 20ml/min Pump Head Clear Tubing Black Tubing
(mm) Part Number Dimensions
Rotor speed: Up to 120 rpm
• Output signal to indicate end of cycle. 562030-T 560984P 560984BA 1.0 x 1.6 561010-D 1.7mm
Dispense pressure: Over 105 Kg/cm²
562030-T 560985P 560985BA 1.4 x 2.0 561011-D 2.1mm
• Large segment digital LED display . I/O: Connection for
562030-T 560995P 560995BA 1.9 x 2.5 561012-D 2.6mm
remote operation
562030-T 560996A 560996BA 2.4 x 3.0 561013-D 3.5mm
• Air-free dispensing. Input voltage: 110-240 VAC -
50/60Hz
Optional Pump Heads
• Instant reverse for snuff-back cuts off Internal voltage: 5 VDC
562030-M 560997P 560997BA 0.25 x 0.75
liquid flow. Dimensions (WxDxH): 7.18” x 3.20” x 6.73”
562030-S 560998A 560998BA 0.50 x 1.00 561008-D 0.9mm
Weight: 2.99 kg
562030-S 560999A 560999BA 0.60 x 1.00
Standards: CE Approved, RoHS
Models 562030-G 562033 0.50 x 2.20 561012-D 2.6mm
Compliant
PPD-130 Peristaltic Pump Dispenser 562030-G 562034 3.00 x 5.00
28. www.fisnar.com 27. info@fisnar.com 29.

Adjustable Finger Switches Autotube Dispenser
Designed for use on a dispenser where it is The autotube system was designed to
not convenient to use a foot pedal, or for dispense liquids, pastes, greases, silicones
operators who prefer to use finger switches and similar liquids directly from the
to standard foot pedals when controlling manufacturer’s "collapsible" tube.
the dispensing controller.
With the autotube method all you have to
These finger switches are easily adjustable do is attach an "adapter" to the material
and can be fitted to a wide range of tube, then drop the tube in a cartridge
cartridges, retainers and barrels. reservoir allowing you to immediately
start dispensing.
Models Dispensing can be controlled by either a foot valve or timed dispenser DSP501N for a
controlled shot. The autotube assembly can be hand held or mounted on a stand.
FS-501V Cartridge and retainer
finger switch Features: Accessories (included):
560023-LF Barrel finger switch
• Eliminates waste. ATD100C ATD200C ATD300C
5601357 5601357 560545
• Avoids material contamination. Connecting Connecting Tip Adapter
Gun Handle and Switch Assembly • Improves operator safety.
Hose
560062A
Hose
560517A 880001-A
6oz Cartridge 8oz Cartridge Adapter "A"
The 560598 gun handle and switch • Prevents tube damage. 5601380 5601381 880001-B
assembly has been designed to hold 6oz Cartridge 8oz Cartridge Adapter "B"
a 790HP valve ensuring the operator Retainer Retainer
has complete control when dispensing Models 5601376 5601376 880001-C
materials. ATD100C Autotube Dispenser Retaining Cap Retaining Cap Adapter "C"
100g Tube 560545 560545 880001-D
This allows for a controlled and efficient ATD200C Autotube Dispenser Tip Adapter Tip Adapter Adapter "D"
overall application. 200g Tube 880001-A 880001-A 880001-Blank
ATD300C Autotube Dispenser Adapter "A" Adapter "A" Adapter Blank
300g Tube 880001-B 880001-B 560516A
Models Adapter "B" Adapter "B" 1/10 Gal Cartridge
880001-C 880001-C 580091H-A
560598 Gun handle and Adapter "C" Adapter "C" 1/10 Gal Retainer & Cap
switch assembly
880001-D 880001-D
Adapter "D" Adapter "D"
880001-Blank 880001-Blank
Adapter Blank Adapter Blank

TD101 Tube-Gun Dispenser Dual Cartridge Dispense System
The TD101 tube-gun dispenser is The dual cartridge dispense system (DCD)
engineered to specifically address the is an excellent cost-effective solution for
waste and discomfort that result from low volume mixing and dispensing of two-
dispensing materials in collapsible tubes. part materials supplied in dual cartridges.
The fully portable bench-mounted system
This comfortable, balanced design safely is simple to install and program for accurate
protects the tube from damage and the two-part dispensing.
operator from contamination.
DCD systems include a pneumatically
Replacement parts are included, however actuated dual-cartridge piston dispenser
first time users are recommended to which applies pressure to accurately
supply a tube sample. dispense materials contained in a dual
cartridge.
Includes replacement parts: Features:
Features: Specifications:
• 560700 Nozzle • Eliminates waste when dispensing
• 560699 Nozzle nut from tubes. • Dispenser is mounted on a robust bench Operating air supply: 87psi max
• 560698 O-ring support, to allow for height and angle Compressed air supply: 100psi max
• 560697 Lock ring • Avoids material contamination. adjustment when dispensing.
• 560696 Retaining ring
Air requirements: ISO 8573-1, 2.4.2
• 560695 Seal • Improves operator safety. • Includes pinch-valve for increased Pressure adjustments: Variable
• 560705 5" hose accuracy and drip-free dispensing of low
• 560704 Hose fitting Pneumatic connections: 1/4 inch
• Prevents tube damage. viscosity materials.
• 560703 Connector Weight without 32lbs (14.5 kg)
foot pedal:
• 560702 Hose barb • A pneumatic foot pedal enables a Foot pedal weight: 4lbs (1.8 kg)
• 560707 Adapter nut Specifications: hands-free operation.
• 560706 Tip set DP50 weight: 1.45 lbs (0.7 kg)
• 560545 Luer lock adapter DP200 weight: 3.52 lbs (1.6kg)
• 880001-Kit 88001-A, B, C adapter Product Code: TD101 Models DP400 weight: 4.85 lbs (2.2kg)
Maximum tube: 7.38" Sound level: 83 dBA
DP50-1 50ml System
Cycle: Manual (Trigger actuated) Machine directive: 2006/42/EC
Models
Start pressure: Recommended at 20 psi DP200-1 200ml System Compressed air quality EN ISO
TD101 Tube Dispenser (1.38 bar) class: 8473-1:2000
DP400-1 400ml System
Maximum pressure: 50 psi (3.45 bar)
Size: 7.5" x 3" x 6.75"
Weight: Without tube 272g

31.
VPP511 Vacuum Pick-Up System VPP803 Vacuum Pick-Up System
The VPP511 vacuum pick-up system The VPP803 vacuum pick-up system
is designed for delicate handling of is designed for delicate handling of
small parts and components, including small parts and components, including
miniature, surface mount and chip scale miniature, surface mount and chip scale
packages. packages.
This vacuum pick-up system features an The VPP803 is a non-electrical unit that
air solenoid vacuum electrically activated has a vacuum pencil with a small hole that
by pressing a foot pedal. creates a vacuum.
To assemble connect the air hose to To assemble insert the airline tubing into
filtered compressed air 70-100psi (5-7bar) the connector, insert the end of the tubing
and connect fitting to the unit, foot switch into the "PUSH-IN" type connector until
plug, male quick connect and insert it bottoms and connect the air hose to
female plug and male plugs to the unit. filtered compressed air.
Features: Specifications: Features: Specifications:

• Foot pedal controlled. Product Code: VPP511 • No electricity required. Product Code: VPP803
Cycle: Foot pedal control Cycle: Continuous
• Electrically switched using a • Easy to control operation.
Air input: 20 - 100psi Air input: 20 - 100psi
foot pedal.
Vacuum: Vacuum gauge display Vacuum: Up to 16 in. hg
• Uses air only.
Size: 5.50” x 7.00” x 2.63” Size: 5.50” x 7.00” x 2.63”
• No hand movement required.
Weight: 1.59 kg Weight: 1.72 kg
• A non electrical unit.
Parts: Parts:
Models Product Code: Description Models Product Code: Description

(Diameter) (Diameter)
VPP511-LF Vacuum Pick-Up 110V 560047 Vacuum pad 0.140" (3.5mm) VPP803-LF Vacuum Pick-Up Unit 560047 Vacuum pad 0.140" (3.5mm)
VPP803-LF Vacuum Pick-Up Unit 560048 Vacuum pad 0.200" (5.1mm) 560046 Vacuum Pick-Up Pencil 560048 Vacuum pad 0.200" (5.1mm)
560049 Vacuum pad 0.250" (6.4mm) (included) 560049 Vacuum pad 0.250" (6.4mm)
VPPE511-LF Vacuum Pick-Up 200V
560050 Vacuum pad 0.320" (8.1mm) 560050 Vacuum pad 0.320" (8.1mm)
560051 Vacuum pad 0.400" (10.2mm) 560051 Vacuum pad 0.400" (10.2mm)
560052 Vacuum tip #14 0.063" (1.60mm) 560052 Vacuum tip #14 0.063" (1.60mm)

33.
DB815 Foot Dispenser 700PTPCW Pinch Tube Pen
The DB815-SB foot dispenser is a basic air- Pinch tube pens are ideal applicators for manually dispensing
powered dispensing system. continuous beads or applying microdots of low viscosity
liquids such as solvents and cyanaoacrylate glues.
Floor mounted and foot actuated, fluid
will be dispensed only when the foot The disposable pinch tube is the only part of the pen
petal is pressed. that is in contact with the material and discarded when
contaminated.
A three-way air valve is included along
with a built in air regulator. The pinch tube pen can be connected via a wide range
of interchangeable fittings to gravity fed or pressurised
reservoirs.
The DB815-SB model has a suck-back option ensuring that low viscosity liquids do not drip.
Models
This unit is suitable for dispensing all types of fluids. 700PTPCW Dispenser Pinch Tube Pen
Reservoir ordered separately
• Economical and simple to use. Cycle:

Foot pedal:
Maintained by user
Air valve in unit
JC1015 Dispensing Needle Valve Pen
• Wide range of applications.
Air input: 70 - 100psi
Air output: 1 - 100psi The needle valve pen simplifies the application of a
• Barrel suck-back ensures no
Dimensions (WxDxH): low to medium viscosity fluid, which is not affected by
dripping.
DB815: 4.50” x 8.50” x 4.88” contact with metal parts.
• No electric needed. DB815-SB: 4.50” x 8.50” x 5.38”
Weight: Material is fed into the pen from a cartridge or reservoir.
DB815: 1.59 kg The finger control shut off instantly opens and closes the
Models DB815-SB: 1.72 kg material flow.
DB815 Foot Dispenser
The pen is suitable for microdots, beading and potting
DB815-SB Dispenser with
operations.
suck-back
Models
JC1015 Dispensing Pen
Reservoir ordered separately

710PT-LF Pinch Tube Valve VD510 Diaphragm Valve
Engineered for precise control of semi- The VD510 is a diaphragm valve designed
viscous liquids. for precise flow control of low to medium
viscosity materials. The diaphragm
The only part of the valve making contact separates the wetted parts from the
with the fluid being dispensed is the moving parts and, therefore the valve
disposable pinch tube assembly. is ideal for dispensing cyanoacrylates,
reagents, electrolytes, glues, solvents,
The 710PT-LF pinch tube valve provides an paints, alcohol and other volatile
infinite degree of control for continuous substances.
micro-shot applications of low-to-semi
viscous materials. When the air pressure is applied the valve will open and the material will be dispensed. At
the end of the dispense cycle a spring assists the diaphragm to return quickly to its closed
Automatically opening and pinching a moulded polyethylene tube assembly achieves the
state for immediate shut off.
“on/off” control.
Features: Specifications
The shot size or flow rate is determined by the degree of adjustment in releasing the closed
(pinched) tube and by the valve control timer. • Stroke adjustment to fine tune Operating air pressure: 60 - 85psi
shots.
Features: Specifications: Material delivery pressure: 71psi
Flow rate maximum: 0.3 L/min
• Separated wetted parts.
• Throwaway valve and feed Operating air pressure: 60 - 75psi Driving part materials:
tubes. Material delivery pressure: 100psi max Body: AL (Hard coated)
• Suitable for robot integration.
Driving part materials: Piston: SUS303
• Suitable for low-viscosity Body: Plastic Piston seal: NBR
• Suitable for anaerobic fluids.
fluids. Piston: Plastic Wetted part materials: UHMWE-PE
Wetted part materials: Polyethylene Connecting ports:
• Ideal for 2-part epoxies and Air input: M5xP0.8
cyanoacrylates. Connecting ports:
Operating air: 1/4” tube adapter Material inlet: 1/8” NPT
Material inlet: Luer lock Material outlet: Luer lock
Material outlet: Luer lock Weight: 76 g
Models
Models
VD510 Diaphragm Valve
710PT-LF Pinch Tube Valve
VD510-SS Stainless Steel
VD510-UV UV Suitable

37.
MV-0180 Micro Shot Needle Valve CV629 Cartridge Valve
Designed for precision dispensing of The CV629 is a pneumatically operated
all types of fluids from micro shots to valve designed for precision dispensing of
moderate sized beads and dots. many types of fluids, such as solvents, oils,
silicones, glues, UV adhesives, inks etc.
Its lightweight pencil-type grip makes
the valve suitable for either hand-held or The system can be integrated with an
automatic applications. automatic dispensing robot or used as a
bench-dispensing valve. Avoid clean-up
Shot size and flow rate are controlled by the tip size, fluid pressure and the duration that and maintenance by simply replacing the
the valve is open. removable cartridge.
• Aligned air and material inlets for Operating air pressure: 70 - 85psi
• Plastic fluid body for anaerobic Operating air pressure: 60 - 85psi side-by-side mounting. Material delivery Max 300psi
fluids. Material delivery pressure: Max 120psi pressure:
Minimum shot size: Micro dots • Stroke adjustment to fine tune Connecting ports:
• Stroke adjustment to fine tune shot size.
Driving part materials: Operating air input: M5 thread with push-in
shot size.
Body: AL, SS, Plastic fitting for Ø6 O.D. tube
Piston: AL, SS, Plastic • Replaceable cartridge. Material inlet: 1/8" BSPP with push-in
• Positive shut-off.
Piston seal: PTFE fitting for Ø6 O.D. tube
• Microshot deposits. Material outlet: Luer lock adapter
• Micro-shot deposits. Wetted part materials: AL, SS, Plastic
Connecting ports: Weight: 135g
• Fluid is supplied to the material
Air input: 1/8” NPT
inlet through a 1/8" BSPP port.
Material inlet: 1/8” NPT
Material outlet: 1/4” - 28 / Luer lock
Models Models
MV-0180LF Valve, aluminium CV629 Cartridge Valve
MV-0180SS Valve, stainless steel

39.
SV1000SS Stainless Steel Spray Valve VMP30H Poppet Valve
The SV1000SS spray valve provides close The VMP30H is a multi purpose, mini-
tolerance spray dispensing of fluids of up poppet pneumatic valve designed for
to 1000 cps. dispensing low to mid-high viscosity
materials.
The SV1000SS is constructed of stainless
steel to prevent corrosion from volatile The poppet design minimises surface
materials. area and friction between the valve piston
and the material, making it ideal for filled
Designed for spraying flux, urethane, paint, lubricants and for coating, conformal coating materials and extending the life of the
and marking applications. valve seals.
The valve is adjustable by turning the stroke-adjust control at the rear of the valve; this will Features: Specifications
tune the spray pattern. Coating and flow rate are controlled by the fluid pressure, needle
• Suck-back effect to eliminate Operating air pressure: 50 - 85psi
stroke, distance from the valve to the work and the duration the valve is open.
lumping at the end of needle. Material delivery pressure: 85psi max
Features: Specifications Flow rate: MAX 1.2l/min
• Suitable for filled materials. Minimum shot size: 0.01 cc
Driving part materials:
• Stainless steel fluid body. Operating air pressure: 70-100psi
• Separated wetted part. Body: AL hard anodised
Atomising air pressure: 1-30psi
• Stroke adjustments to fine-tune Piston: SUS303
Fluid viscosity range: Up to 1,000 cps • Fine tune shot size by turning the
spray area. Piston seal: NBR
Fluid pressure: 1-100psi knob at the top of valve. Wetted part materials:
Nozzle diameter: 0.028”
• Spray angle of 12 degrees. Chamber, CAP: SUS303
Flow rate: Up to 28 cc/sec
Diaphragm, seal: UHMW-PE
• Operating frequency of 200 cycles / Operating frequency: Over 200 cycles/min O-ring: Viton®
min. Spray angle: 12” Connecting ports:
Spray pattern: Circular (conical spray) Air input: M5 x P0.8
• Nozzle design prevents clogging. Operating air inlet: 10-32 thread, fitting for Material inlet: 1/8” NPT
1/4 tube
Material outlet: Leur lock
• Suitable for spraying paint, flux, Atomising air inlet: 10-32 thread, fitting for
Weight: 1.62 kg
urethane and lubricants. 1/4 tube
Material inlet: 1/8” NPT, fitting for 1/4
tube
Models Weight: 2.9 kg Models
SV1000SS Stainless Steel Spray Valve VMP30H Poppet Valve

41.
VP300 Poppet Valve VMS400 Mini-Spool Valve
The VP300 is a multi purpose, poppet-style The VMS400 is a mini-spool type
pneumatic valve designed for dispensing pneumatic valve designed for dispensing
low to mid-high viscosity materials, such low viscosity to high viscosity
as silicone, RTV, epoxy, rubber adhesive, materials.
grease, liquids containing filler, etc.
When air pressure is applied to the air inlet
A diaphragm located between driving of the VMS400 valve, the spool will be
parts and wetted parts increases the valve forced forward and fluid will be dispensed.
life and reduces valve maintenance.
Shot size and flow rate are controlled by the tip size, fluid pressure and the duration that
Features: Specifications: the valve is open.
• Suck-back effect to eliminate Operating air pressure: 65 - 85psi Features: Specifications:

lumping at end of needle. Material delivery pressure: 85psi
Flow rate: 2.4 L/min max • High pressure fluid input up to Operating air pressure: 65 - 85psi
• Suitable for filled materials. Minimum shot size: 0.05cc
700psi. Material delivery pressure: 711psi
Driving part materials: Flow rate: 5.0 l/min
• Separated wetted parts. • Suitable for high viscosity fluids.
Body: AL hard anodised Minimum shot size: 0.1 cc
Piston: SUS303 Driving part materials:
• Fine tune shot size by turning • Adjustable suck-back effect.
Piston seal: NBR Body, Piston: SUS303
the knob at the top of valve.
Wetted part materials: Spool: SUS420
Chamber, CAP: AL hard anodised Cap: AL hard coated
Diaphragm, seal: UHMW-PE Wetted part materials:
O-ring: Viton® Chamber, CAP: SUS303
Connecting ports; Seal: UHMW-PE lip seal
Air input: M5 x P0.8 Connecting ports:
Material inlet: 1/8” NPT Air inlet / outlet: M5 x P0.8
Material outlet: 1/4” NPT Luer lock Material inlet / outlet: 1/8” NPT
Mounting hole: M5 x P0.8 Weight: 255 g
Weight: 2.58 kg
Models
Models
VMS400 Mini-Spool Valve
VP300 Poppet Valve

790HP-LF High Volume Valve PDV-1000 Auger Valve
The 790HP-LF series high-pressure The PDV-1000 series of precision auger
dispense valve is an economic solution valves is suitable for all medium to high
when dispensing high viscosity materials viscosity paste, epoxy, solder paste and
such as silicones, RTV, sealant and grease. other filled materials.
The 790HP-LF provides a snap-release Capable of dispensing a minimum shot

shut off after dispensing, resulting in a size of 0.508mm using an auger servo-
suck-back at fluid outlet, preventing any motor driven screw.
drip or post extrusion.
PDV-1000 has zero dead space within the valve and can deliver accurate and repeatable
Releasing the air pressure results in the internal spring snapping back into position and dots and beads for any application, whether automated or manually operated.
closing the valve.
This auger style valve is used in conjunction with the RVC900N controller.
• High pressure fluid input up to Operating air pressure: 60psi minimum
2,500psi. Material input pressure: 2500psi maximum • Solder-paste dispensing. Motor voltage: 24V
Valve body:
• Suitable for high-viscosity fluids. Motor: 6-watt, 400RPM
790HP-LF: Aluminium • Microshots 0.020" (0.508mm) (no load)
790HPSS-LF: Stainless steel 0.00003cc. Auger material: Stainless steel
• Replaceable seals.
Connecting ports: Minimum 35,000cps
Air input: 1/4” NPT • Abrasive materials. material viscosities:
Material inlet: 1/4” NPT Minimum shot size 0.020" (0.508mm)
Material outlet: 1/4” NPT • Flexible coupling from motor (filled materials):
Seals: to screw. Gear box ratio: 16:2
O-ring: Viton®
Valve seal: Glass filled PTFE
• No dead space – high
repeatability.
Models Models
790HP-LF High Volume Valve PDV-1000 Auger Valve
790HPSS-LF Valve, Stainless Steel

RV5000DPM Rotary Valve VDP150 Positive Displacement Valve
The RV5000DPM encoder valve is The VDP150 plunger pump is a
designed for continuous operation where pneumatically operated positive
cleaning or refurbishment of a valve is displacement valve designed for
not desirable. A disposable Delrin® auger dispensing constant volume shots of low
screw is accessed through a hinged to medium viscosity materials within 1%.
doorway and can be quickly replaced in The VDP150 has two integral check valves
seconds. to control the flow of material.
The RV5000DPM allows for easy The valve is cycled by applying air pressure
maintenance and is suitable for abrasive to the air ports. For low viscosity materials
materials and two-part fluids. (less than 5,000cps) no fluid pressure is
required, as the material is drawn into the
Specifications:
Removing and replacing the auger maintains the valves accuracy and increases the life displacement chamber by the plunger.
Operating air pressure: 60 - 85psi
of the valve by providing less wear-and-tear on the motor. Three versions of the valve are
available: 8, 16 and 32 pitch. Features: Material delivery spring: ø0.3 mm - 4.26psi
Material delivery spring: ø0.5 mm - 17.06psi
• Positive displacement metering. Cycle rate: 120 cycles/min
Features: Specifications Minimum shot size: 0.005 cc
• Integral inlet/outlet check valves. Maximum shot size: 0.15 cc/cycle
• Solder paste dispensing. Size: 1.45" x 3.6" x 5.88"
(37 x 91 x 149mm) Measuring type: Plunger
• Microshots 0.010" (0.254mm) Minimum shot size: 0.020" (0.508mm)
• Stroke adjustment to fine tune shot Driving part materials
0.000015cc. size. Cylinder body / cap: AL hard anodised
Maximum fluid delivery 30psi (2.1 bar)
pressure: Piston: SUS303
• Abrasive (filled) materials. Motor voltage: 24V Check body: SUS303, RULON
Motor: 6-watt, 400 RPM Wetted part materials:
• Motor reverse capability. (no load) Chamber, CAP, CV body: SUS303
Connecting ports: Plunger: SUS420
• No dead space - high repeatability. Fluid inlet: Female Luer lock (tin coating)
Fluid outlet: Male Luer lock Check valve: PEEK
• Replaceable wetted feed path. Wetted part materials: Delrin®, Nylon, Viton® O-rings: Purfluore
Viscosity: 30,000 - 1,300,000cps Connecting ports:
Models Mounting: 1" (25.4mm) body Air input: M5xP0, 4 mm
channel or valve fitting
RV5000DPM Rotary Valve
Disposable Material Path bracket
RV5000DPME Rotary Valve Weight: 0.75lbs (240g) Models
Disposable Material Path
Encoder Model VDP150 Positive Displacement Valve

DC200 Valve Controller VC1195N 4-Way Valve Controller
The DC200 multi-purpose digital controller The VC1995N is a 4-way valve controller
is a cost-effective and productivity- that can be used to control one or two
focused controller and is capable of valves simultaneously.
controlling all Fisnar valve series.
This controller is suitable for valves:
With a universal power supply, it is a fully
'plug and play' system and can be used 790HP-LF, 700RV, 800RV, VBP117, VDP305,
immediately with its accompanying tools VDP100, HPN200, HP600S, HP600L,
and accessories. VDP150, VMS400, VMP30H, VP300 and
MV-0180LF.
This system uses a highly responsive air pressure management system, coupled with a
digital timing circuit and display, to provide consistent, repeatable control of all types of The VC1195N provides a continuous "valve-off" state and remains in this mode until a signal
valves. is received to switch to "valve-on" mode.
Features: Specifications: When the timer is off, the valve will remain in "valve-on" state as long as the foot switch is
pressed or to allow a robot to control the operation. When the timer is selected, a momentary
• Air input tolerance can be set for Product Code: DC200 pulse will activate the timer to open the valve for a programmed period and then close the
consistent pressure. Cycle rate: 600+ cycles per minute valve automatically.
Timer: 0.008 to 9999 seconds
• Can be locked to keep programs
Programs: 10 memory slots This valve controller will deliver accurate and repeatable dots or beads for any application.
from being modified.
Input AC to power supply: 100-240 VAC - 50/60Hz
Output DC from power 24 VDC - 0.75 Amp
• Auto purge to prevent premature
supply:
curing of material.
Air input: 100psi maximum
• Timing interval from 0.01 - 31 Product Code: VC1195N
• Dispense counter for tracking Air output: 0-100psi
seconds. Dispense time: 0.01-31 seconds
completed dispense cycles. Relative humidity: 20 - 90%
(no condensation) Cycle initiation: Momentary or continuous
• Fast response internal
• Multiple dispensing modes for easy Dimensions (WxDxH): 7.09” x 7.68” x 3.15” Voltage: 100 - 240 VAC 50/60Hz
pneumatic solenoid.
use in many applications. Weight: 1 kg Internal voltage: 24 vdc
Standards: CE Approved, RoHS Air input: 70 to 100psi (5 to 7 bar)
• Instructions can derive from
Compliant Air output: 1-100psi (0.1-7 bar)
remote robotic device or foot
Size: 10.4" x 8.25" x 2.75"
switch.
Models Weight: 1.9 kg
DC200 Valve Controller Models
VC1195N 4-Way Valve Controller

SVC100 Spray Valve Controller RVC900N Auger Valve Controller
The SVC100 is a programmable spray The RVC900N controls the PDV-1000
valve controller providing the adjustment series of auger valves and the RV5000DPM
controls necessary for a clean spray disposable cartridge auger valve.
application.
The controller is programmable for timed
By controlling the relationship (time) shots from a minimum of 0.01 seconds.
between the fluid start signal and the Motor speed output is maintained and
atomising signal, it is possible to open kept constant, compensating for any
each independently. change in material viscosity.
Features: Specifications: RVC900N supplies material pressure to the barrel, adjusted via a regulator and pressure
gauge. The digital timer can accept time intervals from 0.01 seconds – 99.99 seconds. A
• Fluid air line pressure starts Dispense time: 0.001 - 99.99 seconds reverse timer and speed control sets the amount of controlled suck-back at the end of the
momentarily after the atomising Dispensing selection: LCD digital display dispense cycle.
pressure opens.
Voltage:
SVC100-110 110VAC 50/60Hz The controller delivers accurate and repeatable dots and beads for any application, whether
• Atomising pressure stays on automated or manually operated.
SVC100-220 220VAC 50/60Hz
momentarily after the fluid cuts off.
Dimensions (WxDxH): 9.05” x 7.32” x 3.54”
• Easy user interface. Weight: 2.72 kg Features: Specifications
• Easily interfaced with a PLC. • Simple to program. Size: 9.05" x 8.26" x 2.76"
(235 x 210 x 70mm)
• Timed or continuous spray. • Eight stored programs. Time range: 0.01 - 99.99 seconds
Resolution: 0.001 seconds
• Clean, clog-free cut off. • Auto or manual control. Voltage: 100 - 240 VAC 50/60Hz
Storage: 8 programs
• Easy to set up and operate. • Constant motor speed. Remote operation: External +24VDC
Communication: I/O
• "On-the-fly" adjustment. • Adjustable forward and reverse
Output pressure: 0 - 60psi 4 bar (regulated)
speed and time.
Manual operation: Foot switch
• Digital air output display (psi/bar).
Display: 128 x 64 pixels
Models Voltage: 85 - 264 VAC
Models RVC900N Auger Valve Controller Weight: 1.65 kg
SVC100-110 110V Controller 110/220V CE
SVC100-220 220V Controller

Reservoir Tanks Stainless Steel Reservoir Tanks
Reservoirs tanks are used to feed bulk Stainless steel reservoirs are available
fluids to a valve or dispensing pen. as small pressure reservoirs for use
in wide application demands and
A variety of sizes are available including compact agitated pressure reservoirs,
bottom porting for very high viscosity designed to best suit fluids which
liquids and top porting for low to medium require gentle or fast agitation.
viscosities.
Manufactured with stainless steel,
An "open top" style is used if liners are these reservoir tanks ensure that
required to prevent the material from the material contents are not
making contact with the sides of the contaminated by corrosion.
container or if the fluid requires an agitator.
Specifications: Small pressure reservoirs can be supplied for all types of requirements with a different
surface finish as well as fitted with air agitators, low level sensors and additional ports.
Model Size Style Agitator Ported Base ASME Max Regulator Material
Rating Pressure Gauge 10ft. Compact agitated pressure reservoirs have been designed to work well in busy environments
(psi) (psi) Hose and can provide intermittent or constant agitation. If required compact agitated pressure
IJ2601-107 2 Qt Bottle No Top Metal No 50 0-60 1/4" reservoirs can be supplied with a different surface finish.
IJ-0100 1 Gal Bottle No Bottom * Metal Yes 125 0-100 3/8"
IJ-0100R 1 Gal Bottle No Top Rubber Yes 125 0-100 1/4"
IJ-0200 2 Gal Bottle No Bottom * Metal Yes 125 0-100 3/8"
Specifications:
IJ-000R 2 Gal Bottle No Top Rubber Yes 125 0-100 1/4"
IJ-83B-500 2.8 Open No Top ** Metal Yes 80 0-60 1/4" Model Max Working Capacity Weight Body Body Overall Overall Height
Gal Top Pressure (Litres) (kg) Inner Outer height width without
(psi/bar) Diameter Diameter (mm) (mm) lid
IJ-83Z-211 2.8 Open Yes Top ** Metal Yes 80 0-60 1/4"
(mm) (mm) (mm)
Gal Top
FT1 100/6.9 1 2 100 106 225 182 150
IJ-0300 5 Gal Bottle No Bottom Metal Yes 125 0-100 3/8"
IJ-0300R 5 Gal Bottle No Top Rubber Yes 125 0-100 1/4" FT2 100/6.9 2 4 100 106 360 182 300
FT5 100/6.9 5 7 149 155 390 202 321
All reservoirs are supplied with a 10" (3.05m) material hose and 1/4" (6.35mm) airline. FT10 100/6.9 10 14 200 206 484 237 395
Parts Product Code: Description
560554 Material shut off valve assembly for reservoirs marked *
IJ-83B-RL Replaceable liner for IJ-83B-500 and IJ-83Z-211 marked **
560934 Regulator gauge (included)
560779 Regulator (included)
560944 O ring EPDM for bottle style reservoirs (included)
(560944 Viton® and 560944T PTFE encapsulated Viton® o ring optional)

PP300 Clear View Pressure Chamber DA35 Autocan Extruder
The PP300 clear view pressure chamber is a see- The DA35 extrudes medium to high viscosity
through pressure chamber for dispensing low viscosity material, such as paste, silicone and grease
liquids directly from bottles and up to 1lb (0.45kg) jars. under pressure directly from a pre-filled can.
Suitable for automatic and semi-automatic
Regulated air pressure forces the liquid in the bottle controlled dispensing applications, which
up through a disposable tube to a connector, which require a constant supply of air-free material.
can be interfaced to a valve or dispensing pen.
By using the DA35, air bubbles and material
PP300 is available in glass for control of hazardous voids that are caused by handling or decanting
materials such as solvents and cyanoacrylates. viscose material are prevented. The can is
prepared by cutting off its top, the extruder
There is no need to transfer material from supplier’s container. Users are able to open the pump body is lifted and the can placed in
lid of the pressure chamber, place bottle inside, insert polyethylene tube into bottle and position.
secure the chamber. The air pressure is fed through the air regulator which pressurises the
chamber and allows the material to travel to the thru-chamber connector and out via the The extruder pump body is fitted with a follower-plate that seals and follows the material as
connected tube to a pinch tube valve or pinch tube hand-held pen. the level drops to wipe the sides of the can clean limiting waste. The fluid is pressure fed by
reinforced hoses to a valve, which is either mounted to a robot or operator held with a gun
Features: Specifications: handle. The valve is actuated by a valve controller.
• All material contact parts are Size: 6.00” x 6.00 x 11.00”

disposable. (15.24 x 15.24 x 27.94 cm) • Air rams to assist pumping of Size: 8.46 x 17.32
ID: 3.60” (91.44mm) materials. (215 x 440 mm)
• Material visible without having to Inside 8.70” (220.98mm) Height adjustment: 21.65" min - 28.35" max
open the chamber. height: • Adjustable air ram pressure. (550 mm min -
Air input: 70 to 100psi (5 to 7 bar) 720 mm max)
• An ideal choice for dispensing Air output: From regulator max 30psi (2 bar) • Simple load mechanism also Weight: 12.73kg
cyanoacrylate without Weight: Glass 4.20kg provides easy cleaning. Power input for sensing: 110-220V 50-60Hz
contamination, waste or hazard to Disposables: Lines and fittings are polyethylene Air input pressure: 35 - 100psi
the user. • No need to transfer material. Maximum output 850psi
pressure:
• 0-30psi gauge. • Easy hook up for automatic systems. Fluid viscosity range: 30,000 - 300,000 cps
Ratio: 8.5
Models Models Volume per stroke: 5cc
DA35 Autocan Pump Maximum pump speed: 60cpm
PP300-GL-A Glass Clear View
Maximum operating 50°C
Pressure Chamber DA35-1kg Follower Plate 1kg temperature:
DA35-3kg Follower Plate 3kg Air inlet / fluid outlet 1/4" npt (f )
size:

EP1300N Can Extruder System EP1305N Pail Extruder
The EP1300N can suit a range of can and pail sizes A low-pulse pump design that when used in
together with differing material characteristics, such conjunction with a fluid regulator, makes the system
as paste, silicone or grease and has been designed suitable for automatic production dispensing
for quiet operation when handling medium to high applications. These applications require a constant
viscosity fluids. supply of air-free material. Air bubbles and material
voids, caused by handling or decanting high viscosity
A low-pulse pump design that when used in fluids, are prevented.
conjunction with a fluid regulator, makes the system
suitable for automatic production dispensing The EP1305N is designed for a 5 gallon pail of medium
applications. These applications require a constant to high viscosity fluid. Ideal for silicones and grease.
supply of air-free material. Systems are rated at 15:1 and provide a maximum of
996psi regulated material pressure.
• Material delivered air-free. Size: 10.04" x 9.64" x 26.73" • Material delivered air-free. Size: 19.68" x 15.74" x 47.24"
(255mm x 245mm x 679mm) (500mm x 400mm x 1200mm)
• Air-rams to assist pumping of Height 17.68" min x 26.73" max • Wipe-clean action. Height 29.72" min x 47.24" max
materials. adjustment: (449mm min - 679mm max) adjustment: (755mm min - 1200mm max)
Weight: 18.7 lbs (8.5kg) • Air-rams to assist pumping of Weight: 52.8 lbs (24kg)
• Adjustable ram pressure. Power input for 220V 50-60Hz - 20 Watts materials. Power input for 220V 50-60Hz - 20 Watts
pump sensing: pump sensing:
• Electrical extruder motor. Air input 30 - 100psi • Adjustable air-ram pressure. Air input 30 - 100psi
pressure: pressure:
• No need to hand transfer material. Maximum Max 996psi - 68.6 bar • Electrical extruder motor. Maximum Max 996psi - 68.6 bar
output output pressure:
• Easy hook up for automatic systems. pressure:
• Simple load mechanism also Ratio: 15:1
Ratio: 15:1
provides easy cleaning. Fluid viscosity 10,000 - 600,000 cps
Fluid viscosity 10,000 - 600,000 cps range:
range:
Models • PTFE wetted parts. Minimum 0.01 cc/shot
Minimum 0.001cc/shot volume per
EP1301NPump Electric 1kg (1qt) Can volume per stroke
15:1 220V stroke: Models
Maximum 50°C
EP1301WP Follower Plate for 1kg (1qt) Can Air 80 l/min EP1305N Pump Electric 20kg (5 Gal) operating
Included with EP1301N consumption: 15:1 220V temperature
EP1303N Pump Electric 3kg (1 Gal) Air inlet / fluid 1/4 npt (f ) EP1305WP Follower Plate for 20kg Air inlet / fluid 1/4 npt (f )
15:1 220V outlet size: (5 Gal) Pail outlet size:
EP1303WP Follower Plate for 3kg (1 Gal) Can Wetted parts: 304 and 17-4 pH Stainless Included with EP1305WP Wetted parts: 304 and 17-4 pH Stainless
Included with EP1303WP Steel, PTFE, Viton®, PEEK Steel, PTFE, Viton®, PEEK

EP1310C Pump System EP1320C Pump System
A powerful medium ratio system for controlled fluid A powerful medium-ratio system for controlled fluid transfer
transfer from 1/10th gallon (310ml) plastic cartridges. from 1/10th gallon (310ml) plastic cartridges. Suitable
Suitable for silicone type fluids, the system integrates a for silicone type fluids. The system integrates a dual (A +
low-pulse pump design that can be used with a manual B) tandem cartridge arrangement for continuous-flow
hand valve or connected to an automatic production management. A low-pulse pump design allows automatic
robot for controlled dispensing applications. control of dispensing applications.
The EP1310C is designed to easily transfer material for The EP1320C tandem cartridge pump is designed to easily
controlled dispensing via a high pressure valve. The transfer material for controlled dispensing via a high pressure
suitable viscosity range is 5,000cps - 600,000cps. valve. The suitable viscosity range is 10,000cps - 600,000cps.
Rated at 15:1 the system provides a maximum of Rated at 15:1 the system provides a maximum of 995psi
996psi regulated material pressure. The cartridge is regulated material pressure. The A & B cartridge management
contained with a metal jacketed cylinder. automatically switches from either A to B or B to A when the
cartridge is exhausted. Cartridges are contained in metal
Features: Specifications: jacketed cylinders.
• Material delivered air-free. Size: 8.86" x 6.69" x 25.55" Features: Specifications

(225 mm x 170 mm x
• Wipe-clean action. 649mm) • Material delivered air-free. Size: 10.71" x 11.34" x 25.55"
Weight: 15kg (272 mm x 288 mm x 649 mm)
• High-pressure regulation. Power input for 220V 50-60Hz - 20 Watts • Wipe-clean action. Weight: 18kg
sensing: Power input for 220V 50-60Hz - 20 Watts
• Pressure piston assist. Air input pressure: 30 - 100psi • High-pressure regulation. sensing:
Maximum 995psi Air input 30 - 100psi
• Adjustable piston pressure. output pressure: • Adjustable pressure piston assist. pressure:
Ratio: 15 Maximum output 995psi
• Electrical extruder motor. Fluid viscosity range: 10,000 - 600,000 cps • Electrical extruder motor. pressure:
Minimum volume per 0.01cc/shot Fluid viscosity 10,000 - 600,000 cps
• Simple load mechanism also stroke: • No need to transfer material. range:
provides easy cleaning. Air consumption: 80 l/min Minimum volume 0.01cc/shot
Maximum operating 50°C • Easy hook up for automatic per stroke:
• Easy automatic systems hook up. temperature: systems. Air consumption: 80 l/min
Cartridge size: 300ml - 340ml Maximum 50°C
Models Air inlet size: 1/4" npt (f ) Models operating
temperature:
EP1310C Cartridge Pump Fluid outlet size: 1/4" npt (f ) EP1320C Cartridge Dual Pump Air inlet size: 1/4" npt (f )
15:1 220V Wetted parts: 304 & 17-4 pH Stainless 15:1 220V
Steel, PTFE, Viton®, PEEK Fluid outlet size: 1/4" npt (f )

Dispensing Stands Accessories and Fittings
Dispensing stands are designed to operate as bench workstations. A heavy-duty cast base Liquid Manifolds Brass Brass Brass Brass Stainless
steel
Brass
is provided for precise alignment and positioning of barrels, valves, cartridges and retainers. Provide capability of
An adjustable horizontal arm allows for z-axis adjustment. supplying liquid from
2067 2067A 2081 580108 560738 580109A
one reservoir to up to (6) Female quick Female quick Male quick connect Male quick connect Hose clamp Adapter nipple
connector, connector, 1/8" Barb 1/4" MPT Male metric,
valves. Suitable for 3/8” or 1/4" Barb 1/4" NPT Female 1/4" MPT
Brass Brass Brass White White Black

1/4” tubing.
Product Code: Description: No. of outputs

560737 560614 1508A 561085 561086 580057
560540 Liquid Manifold 2 Barbed fitting male,
1/4" MPT
Reducing nipple,
1/4" MPT
Elbow connector,
1/8" NPT Female,
Female Luer lock
to barb
Luer lock to hose
barb
Quick disconnect
retainer - female
1/4" Barb 1/8" MPT 1/4" Comp. with shut-off
(3/8" Tubing)
White Black Black Black White White
560542 Liquid Manifold 4
(3/8" Tubing)
560543 Liquid Manifold 6
Models Models Models (3/8" Tubing)
580095
Quick connect
580115
Quick connect
2004BA
Male Luer lock
5601449
Male Luer lock
560657
Female connector,
913
Male connector,
retainer - female retainer - female tip adapter cartridge adapter 1/4" NPT, 1/4" MPT,
560021 Barrel & 710PT-LF 560536 MV-0180LF 560549-U Metal 1/10th 560540-1/4 Liquid Manifold 2 w/o shut-off bulkhead 1/4" Tube 3/8" Tube
Valve Stand Mini Valve Stand Gallon Stand (1/4" Tubing) White White White White Nylon White
560542-1/4 Liquid Manifold 4

(1/4" Tubing) 7610
914 560726 560545 7513 560656
Male hose
560543-1/4 Liquid Manifold 6 Male elbow,
1/4" MPT,
Female connector
1/4" NPT,
Male Luer lock tip
adapter connector,
Reduced nipple,
1/4" MPT,
Male hose connector,
1/4" MPT,
3/8" Tube 3/8" Tube 1/8" MPT, 1/4" - 28 UNF 1/4" Comp.
(1/4" Tubing) 3/8" Comp.
White White Brass Brass Brass Brass
Air Manifolds
Provides the capacity of 560714 560715 560724 560725 560701 560703
connecting up to (4) valves Male elbow,
1/8" MPT,
Male connector
1/8" MPT,
Male elbow,
1/4" NPT,
Male swivel elbow,
1/8" NPT,
Barbed fitting,
female 1/8"NPT,
Male quick
connector,
to one dispensers. 1/4" Tube 1/4" Tube 1/4" NPT 1/4" Tube 3/16" barb 1/4" NPT female
Brass Brass Brass Brass Brass Brass
Product Code: Description: No. of outputs

Models Models Models 560055 Air Manifold 2 560704 560716 560727 560735 560740 560741
Barbed fitting, Close nipple Reducer Reducer coupling Elbow connector Reducing nipple
560671NM 790HPLF 560568 MV-0180NM-A 560535 Cartridge 560057 Air Manifold 4 male 1/4" MPT,
3/16" barb
1/4" NPT 1/4" NPT Female,
1/8" NPT Male
3/8" NPT,
1/4" NPT
3/8" NPT,
1/2" Comp
3/8" MPT,
1/4" MPT
Valve Stand Stand Reservoir Stand

Cleanroom Filter / Muffler Brass Brass Brass Brass Brass Brass
Filter cartridge filters air

output to 0.5 microns. Also 560717 560718 560719 560713 560746A 560747
Reducing bushing Hex nipple, Reducing bushing Male fitting Elbow Male push connector Street elbow
provides muffling of exhaust 1/2" - 1/4" NPT 1/8" NPT 1/4" - 1/8" NPT 1/4" NPT, 3/16" 1/4" MPT, 1/4" NPT
Hose 1/4" Tube
air where reduced operating
noise is required. Brass Brass Brass Brass Brass White
Product Code: Description:

560024 Filter/Muffler 560728
Elbow,
560729
Elbow,
560730
Tee 1/8" NPT,
560731
Tee 3/16" tube,
560732
Elbow
560733
Luer lock
1/8" NPT Female, 1/8" NPT Female, 3/16" tube, 3/16" tube, 1/8" NPT male connector
3/16" Barb 1/8" NPT Male 3/16" tube 1/8" NPT 3/16" tube 1/4" - 28 UNF
5 Micron Air Filter
Nylon Nylon White
Models Models Product Code: Description:
5622335 VDP150 & VMP30H 562043 VD510 580101 Air Filter 560734 560745 560546
Reducer Female coupling 1/10 gal. nozzle
Valve Stand Valve Stand 560567 5 Micron Air Filter / Regulator 1/4" NPT,
1/4" - 28 UNF
Luer lock adapter
62.
63.
Robotics Overview F5200N.1 3-Axis Inline Gantry Robot
The model F5200 is a compact and
economically priced gantry robot with
all moving axis above the work piece.
The Unitop™ is suitable for any platform
requiring a gantry type mounting
providing open access under the robot.
The F5200 is also ideal for conveyor fed
automation or installed in work cells
operating as a slave robot.
Programming is simply carried out by

a teach-pendant (included) using the
industry’s leading dispensing software
Gantry Robots Benchtop Robots Vision System that walks the user through step-by-step
Gantry robots have their 3 and 4 Axis Benchtop A robot with a touch instructions to create a sophisticated
axis above the work area dispensing robots for screen display with dispensing operation in minutes.
and are ideal for large automatic dispensing of simulation preview for
dispensing applications. materials. fast quality/error checks.
• Gantry design, allows flexible Working area X/Y/Z (mm): 200 x 200 x 150 mm
operation. Maximum speed (X&Y/Z): 500/320 mm/sec
Total load - Z-Axis: 2 kg
• High resolution 0.001mm. Repeatability: +/- 0.02 mm/axis
Resolution: 0.001 mm/axis
• Z-axis reach allows for larger
Motion control: PTP & CP
applications.
Drive system: Micro stepping
motors
• Tip alignment routine for quick
Data memory: 100 programs
program offsets.
50,000 points/
program
• Program one object for identical I/O signals: 8 inputs / 8 outputs
objects.
External interface: USB / RS232
Cantilever Robot SCARA Robot Robot Accessories Power supply: 100-240 VAC
A compact open access SCARA robots are A wide range of Models Dimensions (WxDxH): 485 x 383.5 x 569 mm
style robot ideal for robotic arms and are accessories to get the
F5200 3-Axis Inline Weight: 25 kg
handling larger loads in used for a high level of most out of a Fisnar
Gantry Robot
a fixed position. manipulation. robot.

F4200N.1 Compact Benchtop Robot F4000N.1 Compact Benchtop Robot
The F4200 is a compact and ergonomically The F4000N.1 series of benchtop industrials
designed benchtop robot. It has been robots are an ideal robot for automating a current
designed to support most general dispensing dispensing application.
applications requiring a high performance
standard and consistent repeatable results. F4000N.1 has a micro stepping motors drive system,
The bench space reduction is an additional PTP and CP motion control with teaching via the
benefit. teach pendant.
Programming the F4200 is simple with the With the various work areas offered almost every
included teach pendant and optional tip application can be fitted on one of the F4000N
alignment. models.
Using the industry’s leading software and Features: Specifications:

included robot software, the teach pendant
provides users with step-by-step instructions • Work area up to 19.6” x 19.6”. Working area X/Y/Z (mm):
and videos resulting in a sophisticated F4300N.1: 300 x 300 x 100 mm
dispensing operation in minutes. • Repeatability 0.02mm.
F4400N.1: 400 x 400 x 100 mm
F4500N.1: 500 x 500 x 150 mm
Features: Specifications • High resolution 0.001mm.
Maximum load / tool: 9.98 kg / 4.99 kg
Maximum speed (X&Y/Z): 800/320 mm/sec
• Work area 7.8” x 7.8”. Working area (X/Y/Z): 200 x 200 x 50 mm • Step & repeat functionality.
Repeatability: +/- 0.02 mm/axis
Maximum speed: 500/200 mm/sec Resolution: 0.001 mm/axis
• Repeatability 0.02mm. • USB port for data transfer and
Maximum load / tool: 3kg / 1kg I/O signals: 8 inputs / 8 outputs
back up.
Repeatability: +/- 0.02 mm/axis External interface: USB / RS232
• High resolution 0.001mm.
Resolution: 0.001 mm/axis Power supply: 100-240 VAC
• Optional PC programming.
Motion control: PTP & CP Dimensions (WxDxH):
• Step & repeat functionality.
Drive system: Micro stepping motors F4300N.1: 490 x 520 x 645 mm
• USB port for data transfer and back Data memory: 100 programs F4400N.1: 590 x 620 x 645 mm
up. 50,000 points/program Models
F4500N.1: 690 x 717 x 814 mm
I/O signals: 8 inputs / 8 outputs F5300N.1 3-Axis Desktop Robot Weight:
• Optional PC programming. External interface: USB / RS232
F4400N.1 3-Axis Desktop Robot F4300N.1 35.5 kg
Power supply: 95-250 VAC
F4400N.1 41.5 kg
Dimensions: 324 x 500 x 465 mm F4500N.1 3-Axis Desktop Robot
Models F4500N.1 46.5 kg
Weight: 20 kg
F4200 Compact Benchtop
Robot
66.
F7000N Series Vision System F7400NV Vision System
The F7000N with program auto The F7400NV with program auto alignment
alignment function features touch screen function features touch screen programming
programming with simulation preview. with simulation preview.
The vision system is supplied complete The vision system includes robot 3 axis -
including the PC, ensuring all components optional 300x300mm or 400x400mm, touch
are compatible, thereby eliminating any screen PC, software, colour camera, camera
costly start-up issues and reducing the control, exlite cognate in-sight white LED, CCD
learning curve. conversion ring (5.20.40.60mm), CCD fixture,
LSC light fixture, frame capture dongle USB,
The system is designed to provide extended line and LAN cable.
automatic dispensing program offsets
The vision system is supplied complete including the PC, ensuring all components are
when the dispensing path of a component
compatible, thereby eliminating any costly start-up issues and reducing the learning curve.
cannot be guaranteed.
The system is designed to provide automatic dispensing program offsets when the
dispensing path of a component cannot be guaranteed.
• Auto aligns within 5mm of workplace Features: Specifications:
Working area X/Y/Z 300 / 300 / 100 or 400 /
offset. (mm): 400 / 100 • Auto aligns within 5mm of Working area X/Y/Z 300 / 300 / 100 or 400 /
Vision system: Robot vision workplace offset. (mm): 400 / 100
• Ideal for irregular dispensing route System operation: Touch screen computer
per component. Vision system: Robot vision
(all in one) • Ideal for irregular dispensing route System operation: Touch screen computer
Camera: USB colour camera per component. (All in one)
• High resolution 0.001 mm. Interface port: LAN Camera: USB colour camera
Frame grabber: USB dongle • Automatic offset of dispensing Interface port: LAN
• Automatic offset of dispensing
Light system: EXLITE cognate in-sight route. Frame grabber: USB dongle
route. white LED
Light system: EXLITE cognate in-sight
Lens: 4x, (2x, 3x optional) • Preview simulation of dispense white LED
• Preview simulation of dispense CCD conversion rings: 5 / 20 / 40 / 60 mm route. Lens: 4x, (2x, 3x optional)
route.
Teaching method: 1. PC software CCD conversion rings: 5 / 20 / 40 / 60 mm
2. Screen touch • Auto offset of coordinates after tip
Models Teaching method: 1. PC software
Software function: 1. Program edit 2. Auto change. 2. Screen touch
F7300N 3-Axis Robot 110/220V CE vision 3. Accept DXF files
Software function: 1. Program edit 2. Auto
F7304N 4-Axis Robot 110/220V CE • CAD DXF and Excel accepted. vision 3. Accept DXF files
F7400N 3-Axis Robot 110/220V CE Models

F7404N 4-Axis Robot 110/220V CE F7400NV Vision System

F8000N Cantilever Industrial Robot F9000N Gantry Industrial Robot
The F8000N series are servo motor driven ball- The F9000N Gantry-Cartesian robotic systems
screw design cantilever robots. A specifically can be easily integrated with in-line industrial
ruggedised aluminium structure prevents automation.
flexing and vibration while maintaining
functionality, providing a precision multiple Gantry industrial robots have all their axes
axis robot ideal for conveyor fed applications. above the work area making them ideal for large
Many projects also require all moving axes to dispensing applications and jobs requiring a
be above the workstation, the F8000N series fourth axis such as when using a spray valve.
provide that capability.
The F9000N Gantry-Cartesian robotic systems can be easily integrated with in-line industrial
automation. F9000N robots are particularly suited to the solar assembly industry as they
Features: Specifications: can be manufactured to any required size.
• AC servo motors with ball screw Working area X/Y/Z Features: Specifications:
design. (mm):
• AC servo motors with ball screw Working Area X/Y/Z
F8800N, F8804N 800 / 600 / 200 {+/-360°}
design. {R}:
• Available in three and four axis F8100N, F8104N 1000 / 800 / 200 {+/-360°}
F9300N, F9304N 300/300/200mm
models. Maximum tool load 5 kg {2 kg}
{+/- 360°}
{R}: • Available in three and four axis
F9600N, F9604N 600/600/200mm
• Repeatability of 0.02mm. Maximum speed 1000 / 500 (mm/sec {360°} models.
{+/- 360°}
X&Y / Z {R}: F9800N, F9804N 800/600/200mm
• Highly rigid frame structure. Repeatability {R}: +/- 0.02 mm/axis • Self contained controller functions. {+/- 360°}
{+/- 0.058°} Maximum speed 1000 / 500 (mm/sec)
• Open access design for in-line Resolution {R}: 0.001 mm {+/-0.001°} • Open access design for in-line (X&Y/Z) {R}: {360°/sec}
operation. Data memory: 100 programs / 20,000 operation. Maximum total load 7kg {1 kg}
step / 20,000 points {R}:
• 100 programs on board. Drive system: AC servo motors • Optional bar code scanning software. Resolution {R}: 0.001 mm {+/- 0.001°}
Motion control: PTP & CP Data memory: 100 Programs
System I/O: 24 inputs / 6 outputs Models 20,000 points/program
Models
User I/O: 32 inputs / 6 outputs System I/O: 24 inputs / 6 outputs
F9300N 3 Axis Gantry Robot
F8800N 3 Axis Industrial Robot Dimensions User I/O: 32 inputs / 32 outputs
(WxDxH) inches: F9304N 4 Axis Gantry Robot Dimensions (WxDxH):
F8804N 4 Axis Industrial Robot
F8800N, F8804N 43.70 x 54.33 x 22.24 F9600N 3 Axis Gantry Robot F9300N, F9304N 26.73 x 27.40 x 19.88 in
F8100N 3 Axis Industrial Robot F8100N, F8104N 56.10 x 64.17 x 24.72 F9600N, F9604N 38.54 x 40.24 x 19.88 in
Weight: F9604N 4 Axis Gantry Robot F9800N, F9804N 38.54 x 40.24 x 19.88 in
F8104N 4 Axis Industrial Robot
F9800N 3 Axis Gantry Robot Weight:
F8800N, F8804N 159 lbs, 179 lbs
F9300N, F9304N 28.94 kg
F8100N, F8104N 254 lbs, 273 lbs F9804N 4 Axis Gantry Robot F9600N, F9604N 36.92 kg
F9800N, F9804N 42.9 kg

F2004 4 Axis SCARA Robot F1300N Rotary Table
F2004N is a 4 Axis high-speed industrial SCARA
The F1300N rotary table provides an efficient
robot. SCARA is an acronym for Selective
method of dispensing a circular pattern on
Compliance Assembly Robot Arm. It is ideal
areas that are difficult to access. The tilting
for high volume and large area dispensing
Z-axis allows controlled rotary dispensing on
applications requiring greater flexibility for
an angle.
automated manufacturing environments,
including conveyors and work cells.
The F1300N dispenses adhesives, silicones,
grease and lubricants and is fully adjustable in
The F2004N dispensing robot can also be used
rotation speed, circle diameter and dispensing
for pick and place applications.
time. Dispense from barrels, cartridges or
valves mounted on the Z-axis.
The Z-axis tilt is easily adjusted to dispense
• Highly rigid frame structure . Rated/Max payload 2/7 kg either on a vertical wall within a cylindrical
(J1 + J2 arm): part or on an outside wall. The system is fully
• Ideal for form-in-place gaskets, Arm length: 00 + 300 mm programmable to control dispense delay,
adhesives, potting, coating, filling Repeatability +/- 0.03 mm, +/- 0.02 mm, degree of rotation and wait period before
and pick & place procedures. J1 + J2 arm, J3, J4: +/- 0.03"
cycling.
Operating range: +/- 125°, +/- 125°, 200mm,
• Positioning repeatability 0.020mm. +/- 360°
Maximum speed 5.6 m/s, 1 m/s, 720°/s Features: Specifications:
• Performs continuous path and (no load):
point-to-point motions. Allowable inertia of 0.003 kgf m.s2 • Touch screen LCD display for easy Cycle initiation: Manual or automatic
J4: set up and operation. Vertical travel: 2.00" (50mm) other
• Software tip alignment routine Data memory 100 programs lengths optional
for quick program offsets when capacity: 1000 points / program • Fully programmable for perfect Rotation speed: 0-60rpm
changing dispensing tips. Drive system: Full digital AC servo dispensing.
Motion control: PTP & CP Air input: 70-100psi (5-7 bar)
• Digital servo controlled motors. Interpolation: All axes • 9 user programmable memories. Air output: 1-100psi (0.1-7 bar)
System I/O: 24 inputs / 6 outputs Dimensions (WxDxH): 635 x 643 x 850
• Multiple I/O communications. User I/O: 32 inputs / 32 outputs • Password protected operator lock Weight: 20kg
External interface: RS232 out mode. Work load: 2kg
• High speed movement up to Working 0 - 40°C Tool load: 10kg
5000mm/sec. temperature: • I/O Interface. Working area: 12" (300mm)
Relative humidity: 20 - 90%
Models Dimensions (WxDxH): 240 x 828 x 834 Models
F2004 4 Axis SCARA Robot Manipulator weight: 37 kg F1300N Rotary Table
Controller weight: 10 kg

Tip Alignment Module TA360U-KIT Tip Adjustment Kit
The tip alignment module is a robotic The TA360U-KIT is a tip adjustment kit that
accessory that allows the user to simply allows precision XYZ movement after a tip
run a function on the robot that will change on a Fisnar robot. After adjustment, tips
automatically offset the program. will secure the device to prevent movement.
This is ideal for dispensing applications The fixture can provide a faster position set-up
that require material or tip changes that than using the tip alignment routine supplied
may alter the position of the dispensing in the Fisnar operation software.
needle.
To operate the TA360U-KIT slide the device
This functionality can also be run onto the mounting bar that is on the robot
through an external control making it head. Secure this into position using the
simple to be used by those not trained screws. Load whatever configuration of
in programming the robotics. syringe or valve that is to be used onto the
front of the device, and secure it into position.
When a tip adjustment is needed, use the robot move commands to position the tip to
Features: Specifications: a known location of the program, such as the first s LINE START position in the program
Adjust the knurled knobs until the tip is in the desired position. Tighten the slotted, knurled
• Easy to use with consistent results. Tip diameter: knobs to prevent the tip from moving out of this new position.
TA4000N / TA7000N 0.23 - 1.83 mm (OD)
• Reduces production downtime. TA9000N 0.265 - 10 mm (OD) Features:
Accuracy: +/- 0.03 mm, +/- 0.02 mm,
• Able to run through an I/O for +/- 0.03" • Universal mounting for all Fisnar
minimal user interaction. TA4000N / TA7000N 0.05 mm robots.
TA9000N 0.1 mm
• Works with both dispensing Working voltage: DC 12V / 24V • Total axis control of X, Y and Z.
needles. Dimensions:
TA4000N / TA7000N 25 x 60 x 33.15 mm • Fast tip alignment ensures less
Models TA9000N 141.5 x 141.5 x 34 mm downtime between changes.
TA4000N F4000N Series
Tip Alignment • No use of the tip alignment software
TA7000N F7000N Series is required.
Tip Alignment
TA9000N F9000N Series Models
Tip Alignment
TA360U-KIT Tip Adjustment Kit

Modular Robot Brackets
A high quality, versatile bracket range with a wide 3-Axis Retainer Bracket Mount Plate
choice of parts.
A-RMB-CR
This product line has been designed to create a • Required for mounting all cartridge
smoother, more timely and consistent dispensing retainers to 3-Axis Desktop and Gantry
experience for the end user. Robots.
• Used in conjunction with cartridge retainer
All parts are fully compatible with the complete bracket (C-CRB).
Fisnar dispensing range of robot and dispense • Allows product to be held at a fixed angle
systems. (0° - 90°).
Cartridge Retainer & Valve Backplate

3-Axis Mounting Bracket A-RMB-3CRVP
A-RMB-3 • Compatible with both 3 and 4 Axis Robots.
• Compatible with all Cartridge Retainers.
• Compatible with all 3-Axis Desktop & Gantry • Optimises fluid flow rate when feeding
robots. valve from a cartridge retainer.
• Mounts directly to Z-Axis and is used to hold • Allows simultaneous fitting of both
valve bracket holder. dispense valve and cartridge retainer.
4-Axis Mounting Bracket Sliding Valve Bracket Holder

A-RMB-4 • Valve bracket holder is inserted into
• Compatible with all 4-Axis Desktop, Gantry and mounting bracket “dovetail groove” and
SCARA robots. locked in place to create a lower Z-Axis
• 3-Axis Bracket Holder is required in addition to working height.
hold syringe/valve brackets.
• Sleeve bushing used to convert bracket
mounting diameter from 15mm (Gantry) to B-SBH For use with all Fisnar Valve
10mm (Desktop). (C-VB Type) & Syringe (C-SB)
• Also allows cartridge retainer brackets to be mounting brackets.
mounted directly to the bracket and fixed at an B-SBHS For mounting square body
angle from 0° - 90°. Fisnar dispense valves -
VMS400, VMP30H, etc.

Valve Bracket Holder - Angled 790HP Valve Mount Bracket

B-SBHA C-VB4
• Compatible with all valve and syringe barrel • Attaches to Valve Bracket Holder.
mounting brackets. • Compatible for use with:
• Valve bracket holder is inserted into mounting - 790HP - High Pressure Valve
bracket “dovetail groove” and locked in place
to create Z-Axis working height. *Valve not included
• Allows valve/syringe to be held at an angle

from 0° - 90°.
710PT Valve Mounting Bracket

Backplate Bottom Clamp Bracket
C-VB2
C-CANB310
• Attaches to Valve Bracket Holder.
• For use with Cartridge Retainer & Valve • Compatible for use with:
Backplate (A-RMB-3CRVP). - 710PT - Pinch Tube Valve
• Allows adapter nut (561129) to be locked in
place allowing quick and easy changeover of
fluid cartridge.
Universal Valve Mounting Bracket Syringe Barrel Bracket 3cc-55cc

C-VB1 C-SB
• Attaches to Valve Bracket Holder (B-SBH/A).
• Attaches to Valve Bracket Holder (BSBH/A).
• Compatible for use with:
• Upper support sleeve holds 30/55cc
- VD510 - Diaphragm Valve
Syringe Barrel.
- VP300 - Poppet Valve
*Valve not included • Additional bushings inserted into upper
support sleeve to ensure compatibility
with 3cc, 5cc and 10cc Syringe Barrels.
MV0180 Valve Mount Bracket • Lower support securely clamps around
C-VB3 boss of Luer lock design to ensure a
repeatable fixed X/Y & Z position when
• Attaches to Valve Bracket Holder. changing syringe barrels.
• Compatible for use with: • Does not impede flow of piston inside
- MV0180 - Mini Needle Valve syringe barrel.
*Valve not included

Cartridge Retainer Brackets
• Used to hold cartridge retainers.
• Various sizes to suit different types/
sizes.
• Requires retainer bracket mounting
plate (A-RMB-CR) to attach to 3-Axis
Desktop and Gantry Robots.
• Is mounted directly to 4-Axis Mounting
Bracket (A-RMB-4).
C-CRB310 1/10th Gallon / 310ml

C-CRB6TS 2.5/6/12oz Techcon
C-CRB6TE 2.5/6/12oz EFD
C-CRB20TS 20oz Techcon
PPD130 Dispense Tool Bracket

C-PPD
• Attaches to Valve Bracket Holder
(BSBH/A).
• Compatible with PPD-130 Peristaltic
Pump Dispenser.

www.fisnar.com

Fisnar Catalogue 1

Uploaded by

Copyright:

Available Formats

Fisnar Catalogue 1

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Fisnar Catalogue 1

Uploaded by

Copyright:

Available Formats

FRONT COVER

Engineered Dispensing Solutions

Using a hand dispenser, all medium to high viscosity

This selection of dispense bottle kits suits all

Product • Silicone-free plastics.

10. www.fisnar.com info@fisnar.com 11.

I.D. I.D. 1/2” 1.5” I.D. I.D. 1/2”

Olive 14 0.063 1.60 8001285 8001291 Aluminium 14 0.063 1.60 8001196

PTFE Lined Dispense Tips Beige

I.D. I.D. 1/2” 1" Aluminium 14 0.063 1.60 8001209

12. www.fisnar.com info@fisnar.com 13.

Product Code: BT-SEL-KIT

14. www.fisnar.com info@fisnar.com 15.

16. www.fisnar.com info@fisnar.com 17.

18. www.fisnar.com info@fisnar.com 19.

Retainer Cap Features:

5601377 Retainer cap with regulator gauge

5601429 Retainer cap for 5601418 CR300 Cartridge Retainer

20. www.fisnar.com info@fisnar.com 21.

Product Code Description

Length Ofrice Size Material

Product Code Description

Available in various widths and thickness to meet a special application.

22. www.fisnar.com info@fisnar.com 23.

24. www.fisnar.com info@fisnar.com 25.

Timed mode Features: Specifications:

26. www.fisnar.com info@fisnar.com 27.

28. www.fisnar.com 27. info@fisnar.com 29.

30. www.fisnar.com 29. info@fisnar.com 31.

32. www.fisnar.com info@fisnar.com 33.

Features: Specifications: Features: Specifications:

Models Product Code: Description Models Product Code: Description

34. www.fisnar.com 33. info@fisnar.com 35.

• Economical and simple to use. Cycle:

36. www.fisnar.com info@fisnar.com 37.

38. www.fisnar.com 37. info@fisnar.com 39.

40. www.fisnar.com 39. info@fisnar.com 41.

42. www.fisnar.com 41. info@fisnar.com 43.

• Suck-back effect to eliminate Operating air pressure: 65 - 85psi Features: Specifications:

44. www.fisnar.com info@fisnar.com 45.

The 790HP-LF provides a snap-release Capable of dispensing a minimum shot

46. www.fisnar.com info@fisnar.com 47.

48. www.fisnar.com 47. info@fisnar.com 49.

50. www.fisnar.com info@fisnar.com 51.

SVC100-220 220V Controller

52. www.fisnar.com 49. info@fisnar.com 53.

54. www.fisnar.com 51. info@fisnar.com 55.

• All material contact parts are Size: 6.00” x 6.00 x 11.00”

56. www.fisnar.com 53. info@fisnar.com 57.

58. www.fisnar.com 57. info@fisnar.com 59.

• Material delivered air-free. Size: 8.86" x 6.69" x 25.55" Features: Specifications

60. www.fisnar.com 55. info@fisnar.com 61.

Brass Brass Brass White White Black

Product Code: Description: No. of outputs

560542-1/4 Liquid Manifold 4

White White Brass Brass Brass Brass

Brass Brass Brass Brass Brass Brass

Product Code: Description: No. of outputs

Valve Stand Stand Reservoir Stand

Filter cartridge filters air