Electronic Unit Injector - Adjust: Pruebas y Ajustes
Electronic Unit Injector - Adjust: Pruebas y Ajustes
Electronic Unit Injector - Adjust: Pruebas y Ajustes
Pantalla anterior
Bienvenido: cr050jxf1
Producto: NO SE HA ESCOGIDO NINGUN EQUIPO
Modelo: NO SE HA ESCOGIDO NINGUN EQUIPO
Configuración: NO SE HA ESCOGIDO NINGUN EQUIPO
Pruebas y Ajustes
C15 and C18 Industrial Engines
Número de medio -SENR9843-13 Fecha de publicación -01/10/2014 Fecha de actualización -22/08/2017
i07462518
Illustration 1 g03882525
Typical MEUI A injector
(1) Solenoid prongs
(2) Top of injector
(3) Height adjustment tool ledge
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/fulltext/fulltextheaderinfoframeset.jsp&calledpage=/sisweb… 1/4
1/3/2019 Búsqueda avanzada de texto completo - SENR9843 - C15 and C18 Industrial Engines
Mechanical Electronic Unit Injectors (MEUI) A have the typical features that are shown in Illustration 1.
The injectors typically have solenoid prongs (1), a flat top to the injector (2), and a ledge for the height
adjustment tool (3).
Illustration 2 g01332476
Injector Mechanism (Typical example)
(1) Rocker arm
(2) Adjusting screw
(3) Locknut
(4) 9U-7227 Injector Height Gauge
To adjust the unit injectors on cylinders 3, 5, and 6 use the following procedure:
1. Put the No. 1 piston at the top center position on the compression stroke. Refer to Testing and
Adjusting, "Finding Top Center Position for No. 1 Piston".
2. Injector height gauge (4) is used to obtain a dimension of 78.0 ± 0.2 mm (3.07 ± 0.01 inch). The
dimension is measured from the top of the unit injector to the machined ledge of the fuel injector
body.
a. Set the injector height tool body on top of the injector tappet body. The rod of the height
adjustment tool should sit on the machined ledge of the injector body.
3. Turn unit injector adjusting screw (2) clockwise until the correct height is obtained.
Note: The top of the injector height tool rod has two steps on it. The middle of the steps should be
flush with the injector height tool body.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/fulltext/fulltextheaderinfoframeset.jsp&calledpage=/sisweb… 2/4
1/3/2019 Búsqueda avanzada de texto completo - SENR9843 - C15 and C18 Industrial Engines
4. Hold the adjusting screw in this position and tighten locknut (3) to a torque of 100 ± 10 N·m
(74 ± 7 lb ft).
5. To adjust the unit injectors on cylinders 1, 2, and 4, remove the timing bolt. Turn the flywheel by 360
degrees in the direction of engine rotation. The direction of engine rotation is counterclockwise, as the
engine is viewed from the flywheel end. This will put the number 1 piston at the top center position on
the exhaust stroke.
7. Remove the timing bolt from the flywheel after all the unit injector adjustments have been made.
Reinstall the valve mechanism cover.
Illustration 3 g03882544
Typical MEUI C injector
(1) Tappet
(2) Electrical connector
Mechanical Electronic Unit Injectors (MEUI) C have the typical features that are shown in Illustration 3.
The injectors typically have a raised tappet (1), and electrical connector (2).
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/fulltext/fulltextheaderinfoframeset.jsp&calledpage=/sisweb… 3/4
1/3/2019 Búsqueda avanzada de texto completo - SENR9843 - C15 and C18 Industrial Engines
a. Turn the adjustment screw clockwise for the injector rocker mechanism until it touches the top
of the injector.
c. Hold the adjustment screw and torque the nut to 55 ± 10 N·m (41 ± 7 lb ft).
3. To adjust injectors 1, 2, and 4 rotate the engine 360 degrees and pin the flywheel.
a. Turn the adjustment screw clockwise for the injector rocker mechanism until it touches the top
of the injector.
c. Hold the adjustment screw and torque the nut to 55 ± 10 N·m (41 ± 7 lb ft).
Copyright 1993 - 2019 Caterpillar Inc. Fri Mar 01 2019 13:31:02 GMT-0300 (hora de verano de Chile)
Todos los derechos reservados.
cr050jxf1
Red privada para licenciados del SIS.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/fulltext/fulltextheaderinfoframeset.jsp&calledpage=/sisweb… 4/4