Wiring Diagram HMC 300 2
Wiring Diagram HMC 300 2
Wiring Diagram HMC 300 2
2. General Drawings
4. Circuit Diagrams
6. Interconnection Diagrams
A General Notes A
All the electrical documentation for the crane is in the Wiring Manual. The set- Circuit Diagrams
up of the electrical equipment becomes apparent based on the information in The functional group of a circuit diagram can be established based on the full
the manual. The Wiring Manual shows, among other things, the functional equipment designation system (comprising system and accessory unit codes).
sequences and serves as a basis for locating faults or identifying spare parts. The main parts of the equipment and thus the equipment diagram can be
found in this functional group. The component designation of the contactors,
General Drawings relays and solenoid-operated switches are based on their operating coils.
B The crane is broken down into several sections which are shown in the Information is also provided here as to what side of the circuit diagram in which B
General Layout Drawings. The individual sections have their own letter code. current circuit the connected contacts can be found. The cross references for
Each section is shown on a separate drawing and is broken down into sub- the coils are on the contacts.
sections which are number consecutively. This letter and consecutive number Terminal Connection Diagrams
together with the “+” symbol make up the location code of the component The Terminal Connection Diagrams provide information about the assignment
(e.g. +L01). The circuit diagrams are marked on the bottom righthand side in of the terminals and their wiring. They show both the internal and external con-
the title block with a location code which is the reference for the majority of nections ( cables and lines) between the individual parts of system.
the components shown in this drawing.
C Interconnection Diagrams C
Set-Up All the electrical lines including their type and cross section belonging to a sys-
The assembly Diagrams show how the switching gear cabinets the switching tem are listed in the Interconnection Diagrams.
racks and the panels are set-up.
Circuit Diagrams
The Circuit Diagrams describe the switching gear and the switching proce-
sondere für den Fall der Patenterteilung oder GM- Eintragung
pflichten zu Schadenersatz. Alle Rechte vorbehalten ,i nsbe-
Weitergabe sowie Vervielfältigung dieser Unterlage, Ver-
dures. This diagram shows the switching gear with all of its single parts and
lines as multi-line representations. The switching and control equipment which
is broken down into several drawings is only shown once as a full accessory
unit graphic symbol with all its contacts and connections. In order to make it
E E
easier to follow the sections of the accessory unit which appear on different cir-
cuit diagrams, cross references are used.
F F
Datum =
Bearb. Instructions on how to Use the +
Gepr. Mobile Harbour Crane Zeichn.-Nr.:
Blatt +
Zustand Änderung Datum Name Norm Urspr./Ers.f./Ers.d. Gottwald Electrical Diagram Booklet 1 Bl.
4
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
Designation System for Systems and Accessory Units Function Groups Function Designation
All the equipment of a system is receives an assignment within the designa-
Propertary data,company confidential. All rights reserved.
A A
tion system. This designation system permits all parts of a system to found
= 04 hydraulic pump drive assemblies .D Power circuitry, three
quickly and to be classified. It may be required under this system to break
down the system into one to three levels: Only the number of levels required = 05 central lubrication phase current
for the code for the particular system will be used. = 06 220 V supply .E Measuring and
= 07 diesel engine system monitoring equipment,
The Designation System for Systems and Accessory Units in accor-
dance with German Industrial Standard DIN 40719 = 11 hoist 1 (holding gear) control voltage generation
B The equipment of a system has been assigned the following designation as = 12 hoist 2 (closing gear) .H DC circuitry B
in the example below:
= 21 slewing gear .M Control voltage
The system code appears in all the documentation of the Wiring Manual in a
special code block; this system code applies to all the accessory units indi- = 31 luffing gear .P PLC inputs
cated in a document. These accessory units will only be assigned accessory = 42 travel gear .R PLC outputs
unit numbers:
= 51 spreader .U Open-loop control, closed
= 00 . M - K 1 1 = 52 hook swivel gear loop control
C C
= 53 boom motor-operated cable reel
Consecutive Number = 54 grab
Installation location
= 61 safety devices
Type of electrical equipment
Grouping mark
= 62 stabilizers
Function designation = 63 safe load indicator ( SLI)
D Grouping mark = 66 video system D
Function group = 67 audio system
System code
= 71 24 V lighting
sondere für den Fall der Patenterteilung oder GM- Eintragung
pflichten zu Schadenersatz. Alle Rechte vorbehalten ,i nsbe-
Weitergabe sowie Vervielfältigung dieser Unterlage, Ver-
= 72 miscellaneous
Accessory Unit Code
= 91 PLC / Profibus (Process Field)
-K11 = 95 PLC / ASI Bus
E E
Accessory units which are marked in (Actuator Sensor Interface)
such a way in the circuit diagram are
referred to in relation to the system = 98 general diagrams
code which is always indicated on the
bottom right side (z.B. = 00.M-K11).
F F
Datum =
Bearb.
Instructions on how to Use the +
Gepr. Mobile Harbour Crane Zeichn.-Nr.:
Blatt +
Zustand Änderung Datum Name Norm Urspr./Ers.f./Ers.d. Gottwald Electrical Diagram Booklet 2 Bl.
4
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
M M
M Machines, Motors ~
3
D N Amplifier, Regulators D
(Operational Amplifier, Control equipments)
E E
S Switch, Selector switch, Auxiliarx switch J
Control switch, Limit switch
F F
Datum =
Bearb.
Instructions on how to Use the +
Gepr. Mobile Harbour Crane Zeichn.-Nr.:
Blatt +
Zustand Änderung Datum Name Norm Urspr./Ers.f./Ers.d. Gottwald Electrical Diagram Booklet 3 Bl.
4
1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 10
A A
+ L 11 = 00 - X 11 : 192
+R Tower cab
W 001 - W 099 DC circuits, electric line circuits
+U Boom W 101 - W 199 3-phase circuits
W 201 - W 299 24 V and 220 V control voltages
E +W Hook swivel gear E
W 301 - W 399 special electric lines (for measuring purposes)
+X Spreader
+Y Motor-operated grab
F F
Datum =
Bearb.
Instructions on how to Use the +
Gepr. Mobile Harbour Crane Zeichn.-Nr.:
Blatt +
Zustand Änderung Datum Name Norm Urspr./Ers.f./Ers.d. Gottwald Electrical Diagram Booklet 4 Bl.
4
1 2 3 4 5 6 7 8 9 10