Rc45iii Cone Crusher Specification
Rc45iii Cone Crusher Specification
Rc45iii Cone Crusher Specification
Cedarapids RC45III
Standard Features
Hydraulic powered thread adjust and clamp system 1.5 hp (1.1 kW) 3-phase crusher mounted lubrication oil pump
5 hp (3.7 kW) 3-phase electric/hydraulic module with manual 115 volt immersion oil heaters with thermostat
controls located up to 15' (4570 mm) from crusher Lubrication oil flow safety switch and warning horn
Non-ferrous thread inserts for wear resistance Unit shipped with oil-filled sump
High efficiency ElJay® Rollercone® roller bearing construction V-belt driven sheave for crusher
Heavy-duty cast steel base frame Alloy steel pinion shaft and gear set
Large unobstructed feed opening Non-bridging sloped feed hopper
Bolt-on replaceable counterweights Specified manganese liners installed and poured
Wide unobstructed discharge Bowl manganese replaceable without dismantling tramp iron
Non-ferrous V-seat wear liners relief system
Quick reset hydro-pneumatic tramp iron relief system Cone manganese replaceable without removing cone head
Long-stroke relief cylinders Interchangeable between standard and fine chambers
Self-contained oil reservoir Clockwise input shaft rotation
Close running deep tapered grooved labyrinth seals Crusher tools: lifting eye, mantle wrench
Optional Equipment
V-belt drives Automatic Lube Oil Circulation Kit (recommended below 40°F/4°C)
Electric motors automatically circulates oil at a predetermined interval to
Electrical control and wiring assist in cold weather start-up
Wire basket hopper extension Skid mounted with motor mount and guard
Overflow chute Export preparation and lift kit
Various manganese configurations
53.5"
(1359 mm)
Radius 20"
19" (508 mm)
(483 mm)
74" 22.25"
(1880 mm) (565 mm)
Maximum
3"
(75 mm) 33.5" (851 mm)
1.88" 12.5"
(48 mm) (318 mm) 32"
(813 mm)
31"
(787 mm)
52" (1321 mm)
Square mounting pattern 5"
(127 mm) 86" (2185 mm)
57" (1448 mm)
Discharge opening diameter
SPECIFICATIONS
Weight Hp rpm lube Hydraulic Heater & Control
pump pump Voltage
rC45III Gross 135-170 150-200 170-225 185-245 205-270 220-320 240-340 260-360 270-380
throughput (122-154) (136-181) (154-204) (168-222) (186-245) (200-290) (218-308) (236-327) (245-345)
*Minimum closed side setting is that point just above bowl float under maximum allowable pressure on tramp iron relief system. This setting can
vary widely depending on nature and condition of the material being crushed. The charts are to be used as guides to crushers and liner selection.
Data is offered as a guide only. Crushing characteristics of various rock and crusher operation will affect results.
www.terexmps.com
Effective Date: March 2012. Product specifications and prices are subject to change without notice or obligation. The photographs and/or drawings in
this document are for illustrative purposes only. Refer to the appropriate Operator’s Manual for instructions on the proper use of this equipment. Failure to
follow the appropriate Operator’s Manual when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty
applicable to our equipment is the standard written warranty applicable to the particular product and sale and Terex makes no other warranty, express or
implied. Products and services listed may be trademarks, service marks or trade-names of Terex Corporation and/or its subsidiaries in the USA and other
countries. All rights are reserved. Terex is a registered trademark of Terex Corporation in the USA and many other countries. © 2012 Terex Corporation.
Terex® Minerals Processing Systems, 909 17th Street NE, Cedar Rapids, IA 52402 USA
Tel +1 319 363 3511 Fax +1 319 399 4871 www.terexmps.com Form 24935 (3/12)