Yamaha: Supplementary Service Manual

YAMAHA
SUPPLEMENTARY SERVICE MANUAL
96 Pgs + 2 flo's
FOREWORD OEOll
This Supplementary Service Manual has been HOW TO USE THIS MANUAL
prepared to introduce new service and new data
for the VT700B, VX500XTRB, VXGOOXTRB/SXB, Particularly important information isdistinguished
VX700XTB/XTCB/XTCDB/XTCPB/SXSB. For com- in this manual by the following notations:
plete information on service procedures, it is
necessary to use this Supplementary Service
Manual together with following manual:
A
The Safety Alert Symbol means ATTENTION!
BE ALERT!
VTSOOA, VTGOOA, MMGOOA, MM7OOA YOUR SAFETY IS INVOLVED!
VX500XTA/XTCA/XTCEA/XrCRA
VX6OOXTA/XTCA/XTCEA/XTCRAlSXA
VX7OOSXA Failure to follow WARNING instructions could
SERVICE MANUAL: result in severe injury or death to the snowmobile
8CY-28197-10 (LIT-12618-01-83) operator, a bystander, or a person inspecting or
repairing the snowmobile.
OEOOl
NOTICE
This manual was written by the Yamaha Motor A CAUTION indicates special precautions that
Company primarily for use by Yamaha dealers must be taken to avoid damage to the snowmo-
and their qualified mechanics. It is not possible to bile.
put an entire mechanic's education into one
manual, so it is assumed that persons using this NOTE:
book to perform maintenance and repairs on A NOTE provides key information that can make
Yamaha snowmobiles have a basic understand- procedures easier or clearer.
ing of the mechanical concepts and procedures
inherent in snowmobile repair. Without such MANUAL FORMAT
knowledge, attempted repairs or service to this All of the procedures i n this manual are organized
model may render it unfit to use and/or unsafe. in a sequential, step-by-step format. The informa-
Yamaha Motor Company, Ltd. iscontinually striv- tion has been compiled to provide the mechanic
ing t o improve all models manufactured by with an easy to read, handy reference that con-
Yamaha. Modifications and significant changes tains comprehensive explanations of all inspec-
i n specifications or procedures will be forwarded tion, repair, assembly, and disassembly opera-
t o all Authorized Yamaha dealers and will, where tions.
applicable,appear in future editionsofthis manual. In this revised format, the condition of a faulty
componentwill precede an arrowsymbol and the
course of action required to correct the problem
will follow the symbol, e.g.,
VX500XTRB, VXGOOXTRBISXB, Bearings
VX700XTB/XTCB/XTCDB/XTCPB/SXSB,
PittingIDamage + Replace.
Vl7OOB
SUPPLEMENTARY SERVICE MANUAL
01997 by Yamaha Motor Corporation, U.S.A. EXPLODED DIAGRAM
1st Edition, June 1997 Each chapter provides exploded diagrams before
All rights reserved. Any reprinting or each disassembly section to facilitate correct dis-
unauthorized use without the written assembly and assembly procedures.
permission of Yamaha Motor Corporation,
U.S.A. is expressly prohibited.
Printed in U.S.A.
OE031
0 0 ILLUSTRATED SYMBOLS
(Refer to the illustration)
lllustrated symbols@to@aredesigned asthumb

tabs to indicate the chapter's number and con-
@ General information
@ Periodic inspection and adjustment
@ Chassis
0 @ Power train
@ Engine overhaul
@ Cooling system
@ Carburetion
@ Electrical
0 8 @ Specifications
@ Optional kit
60 @
lllustrated symbols @ t o @ are used t o identify

thespecifications which appear.
@ Filling f l u ~ d
@ Lubricant
@ Tightening
@ Wear limit, clearance
@ Engine speed
@ Special tool
Q n, v, A
Illustrated symbols @ t o @ i n the exploded dia-

69 gram indicate grade o f lubricant and location of
a lubrication point.
@ Apply locking agent (LOCTITP)
---
@ Apply Yamabond N0.5@
@ @ @ @ Apply engine oil
1 1 1 Q) Apply gear oil

@ Apply molybdenum disulfide oil
@ Apply wheel bearing grease
@ Apply low-temperature lithium-soap base grease
@ Apply molybdenum disulfide grease
@ @ @ @ Use new one
@
CONTENTS
GENERAL INFORMATION .................................. 1 ENGINE ............................................................. 52

MACHINE IDENTIFICATION ........................ 1 ENGINE ASSEMBLY .................................. 52
FRAME SERIAL NUMBER ..................... 1 5001600 ................................................. 52
ENGINE SERIAL NUMBER .................... 1 700 ........................................................ 53
IMPORTANT INFORMATION....................... 2
LOCTITEe ................................................2 CARBURETION ................................................. 54
ENGINE ......................................................... 3 CARBURETORS .......................................... 54
THROlTLE OVERRIDE SYSTEM 500/600 ................................................. 54
(T.O.R.S.) CHECK ................................... 3 700 ........................................................ 55
POWER TRAIN ............................................ 4
DRIVE V-BELT ........................................ 4 ELECTRICAL ...................................................... 57
DRIVE CHAIN ......................................... 6 GRIP WARMER SYSTEM ........................... 57
TUNING ..................................................... 9 CIRCUIT DIAGRAM (VT700) ................ 57
CLUTCH ..................................................9 TROUBLESHOOTING .......................... 58
GEAR SELECTION ................................ 26 PASSENGER GRlP WARMER
FRONT SUSPENSION .......................... 29 (VT700) ................................................. 59
REAR SUSPENSION ............................ 30 PASSENGER GRlP WARMER SWITCH
(VT700) ................................................. 59
CHASSIS ..........................................................33 RESISTOR (VT700)............................... 60
SKI (VX7OOXTCP) ....................................... 33
INSPECTION......................................... 34 SPECIFICATIONS .............................................. 61
FRONT SUSPENSION ................................ 34 GENERAL SPECIFICATIONS ...................... 61
HANDLING NOTES .............................. 34 MAINTENANCE SPECIFICATIONS ............ 64
INSTALLATION .................................... 35 ENGINE ................................................. 64
POWER TRAIN ..................................... 73
POWER TRAIN ................................................. 36 CHASSIS ..............................................81
PRIMARY SHEAVE ..................................... 36 ELECTRICAL ........................................ 82
SECONDARY SHEAVE ............................... 37 CABLE ROUTING <500/600> ..................... 84
ASSEMBLY .......................................... 37 CABLE ROUTING <700> ............................ 87
DRIVE CHAIN HOUSING ............................ 38
WITHOUT REVERSE MODEL ..............38
INSTALLATION ....................................39
DRIVE CHAIN HOUSING AND
JACKSHAFT INSTALLATION .............. 40
WITH REVERSE MODEL ......................41
INSTALLATION .................................... 43
BRAKE .........................................................44
SLIDE RAIL SUSPENSION ......................... 45
VX6OOSX. VX7OOSXS .......................... 45
V n O O .................................................... 46
FRONT AXLE AND TRACK ........................ 51
INSTALLATION .................................... 51
MACHINE IDENTIFICATION
lEOOl
GENERAL INFORMATION
MACHINE IDENTIFICATION
FRAME SERIAL NUMBER
The frame serial number @ is located on the
right-hand side of the frame (just below the front
-- of the seat).
ENGINE SERIAL NUMBER

The engine serial number @ is located on the
right-hand side of the crankcase.
NOTE:
Designs and specifications are subject t o change
without notice.
IMPORTANT INFORMATION 1-
IMPORTANT INFORMATION
LOCTITE"
After installing fasteners that have LOCTITEmap-
plied, wait 24 hours before using the machine.
This will give the LOCTITEmtime to properly dry.
THROTTLE OVERRIDE SYSTEM (T.O.R.S.) CHECK
1- ADJ
ENGINE
2E122
THROlTLE OVERRIDE SYSTEM (T.O.R.S.)
CHECK
When checking T.O.R.S.:

Be sure the parking brake is applied.
Be sure the throttle lever moves smoothly.
Do not run the engine up t o clutch engagement
r/min. Otherwise, the machine could start mov-
ing forward unexpectedly, which could cause
an accident.
1. Start the engine.
2. Hold the pivot point of the throttle lever away

from the throttle switch @.
3. Press @ the throttle lever gradually.
The water temperature warning light
(VXGOOXTR/SX) or diagnosis indicator light
(MMGOOP) should turn on and off and the
engine should run between 2,800 and 3,000 r/
min.
If the engine does not run between 2,800 and

3,000 r/min, stop the engine by turning the main
switch t o the "OFF" position and check the elec-
trical system.
DRIVE V-BELT
POWER TRAIN
DRIVE V-BELT
When installing the n e w V-belt, make sure that it

is positioned within the specified distances @
from the edge of the secondary sheave.
If not, the clutch engagement speed w i l l be
changed. The machine may move unexpectedly
when the engine is started.
Adjust the V-belt position b y removing or adding
a spacer @ on each adjusting bolt.
For this adjustment, consult a Yamaha dealer or
another qualified mechanic.
As the V-belt wears, adjustment may be neces-

sary. To ensure proper clutch performance, the
1 V-belt position should be adjusted b y adding a
spacer on each adjusting bolt when the V-belt
position reaches below the edge.
For this adjustment, consult a Yamaha dealer or
another qualified mechanic.
I
New belt width:

34.5 rnm (1.36 in)
Belt wear limit width:
32.5 m m (1.28 in)
1. Measure:
V-belt position @ or @
NOTE:
Install the new V-belt onto the secondary sheave
only. Do not force the V-belt between the sheaves;
the sliding and fixed sheave must touch each
other.
Standard V-belt height I

(Below sheave surface) a:
500,600
- -
0 2 mrn (0 0.0787 in)
Standard V-belt height @:
700
-0.5 - -
1.5 m m (-0.02 0.059 in)
INSP
DRIVE V-BELT
2. Adjust the position of the V-belt by removing
or adding a spacer@ on each adjusting bolt@.
V-belt height adjustment
500,600:
To move V-belt up: Add spacer
To move V-belt down: Reduce spacer
700:
To move V-belt up: Reduce spacer
To move V-belt down: Add spacer
3. Tighten:
Adjusting bolt
Adjusting bolt:
bN 10m. (1.0 m kg, 7.2 fi ib,
4. Inspect:
Drive V-belt
Cracks/damage/wear + Replace.
Oil or grease on the V-belt + Check the
primary and secondary sheaves.
5. Inspect:
Primary sheave
Secondary sheave
Oil or grease on the primary and secondary
sheaves + Use a rag soaked i n lacquer
thinner or solvent to remove the oil or
grease. Check the primary and secondary
sheaves.
6. Measure:
Drive V-belt length @
Out of specification + Replace.
-
Drive V-belt length:
1,129 1,137 mm (44.4 - 44.7 in)
1,119 - -
1,129 mm (44.1 44.4 in)
DRIVE CHAIN
Oil level inspection
The engine and muffler will be very hot after the

engine has been run. Avoid touching the engine
and muffler while they are still hot with any part
of your body or clothing during inspection or
repair.
1. Place the machine on a level surface.

2. Check:
Oil level
3. Remove:
Muffler spring
Checking steps:
Remove the dipstick @ and wipe it off with a
clean rag.
Reinstall the dipstick.
There is a magnet attached t o the end of the

dipstick. It is used t o remove any metal par-
ticles that may accumulate i n the drive chain
housing. When removing the dipstick be sure
to:
Pull it out slowly and gently so the metal
particles do not fall off the magnet back into
the drive chain housing.
Wipe off the magnet before reinserting the
dipstick into the drive chain housing.
Remove the dipstick and check that the oil is

between the upper and lower levels. If not,
add oil to the upper level.
@ Upper level
@ Lower level
For models without a reverse transmission.
For models with a reverse transmission.
DRIVE CHAlN mlINSP 0
Recommended oil:
b% Gear oil API GL-3 SAE #75 or #80
Make sure that no foreign material enters the

gear case.
Reinstall the dipstick and fit the loop @ of

the dipstick handle onto the projection @ o f
the gear case.
4. Install:
Muffler spring
DRIVE CHAIN (INSPI]
AD
J
TUNING
CLUTCH
High altitude
Specifications Model: VX500XTR
El Elevation - 3,500 ft,1,000 m 3,000 - 5,000 ft 4,500 - 7,000 ft 6,500 - 10,000 ft

H Idle speed Approx. 1,600 r/min t t t
Clutch engagement Approx. 4,000 r/min 4,100 rlmin 4,200 rlmin t
Shift speed Approx. 7,800 rlmin t t t
El Main jet # I 51.3 (STD)
Pilot (slow) jet #45 (STD) See MAINTENANCE SPECIFICATIONS (High altitude settings)
ldle mixture screw 1-314 (STD)
El Gearing 22/39 (70L) 21/39 (68L) 20139 (68L) 19/39 (68L)
!llPrimary spring
Color W-P-W t Y-P-Y 0-P-0
Length 78.7 m m t 77.4 m m 74.6 m m
Preload rate 30 kg - 2.25 kg/mm t 30 kg - 2.5 kg/mm 30 kg - 3.25 kg/mm
Wire diameter 05.5 m m t 05.8 m m 06.0 m m
Outside diameter 060 m m t t t
Weight (1D) 8AB t t t
Weight rivet Steel 13.3 (OUT) Aluminum 10.3 (OUT) None (OUT) None (OUT)
None (IN) None (IN) None (IN) None (IN)
Weight bushing Duralon t t t
Roller outer dia. 015.0 m m t t t
Roller bushing Duralon t t t
Pri. clutch shim None t t t
D l Secondary spring
Color R t t t
Length 75 m m t t t
Preload rate 80" (2-6)
t t t
729 kgmmlrad
Wire diameter 165.3 m m t t t
Outside diameter 1669.5 m m t t t
kil Sec. torque cam 45" t t t
r
[hl Sec. clutch shim 1.0 m m t t t
Setting chart Model: VX500XTR
Elevation Clutch setting Remark

(Rivet position: OUTER 1 INNER)
Oft ..............................................
Production
Weight : 8AB
Rivet : Steel 13.3 / NONE
Primary spring : 30 kg-2.25 kglmm
Roller : 015.0
Gearing : 22/39 (70LINKS)
Sec. Preload : 80" (2-6)
Torque cam : 45"
3,000 ft - .............................................
(900 m)
3,500 ft - - - - - - - - - Weight : 8AB ....................
(1,000 m) Rivet : Aluminum 10.3 / NONE
Primary spring : 30 kg-2.25 kg/mm
Roller : 015.0
4,500 ft -- -- ---- Sec. Preload : 80" (2-6) ....................
(1,400 m) Torque cam : 45"
5,000 ft - -A-
:.----------------------------------------------.
(1,500 m) Weight : 8AB
Rivet : NONE / NONE
Roller : 015.0
Gearing : 20139 (68LINKS)
Torque cam : 45"
6,500 ft -----------------------------------------.
(2,000 m)
7,000 ft - - - - - -V- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
(2,100 m)
Weight : 8AB
Rivet : NONE /NONE
Roller : 015.0
Torque cam : 45"
10,000 ft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(3,000 m)
v
i
Specifications Model: VXGOOXTR
.El Elevation - 3,500 ft/1,000 m 3,000 - 5,000 ft 4,500 - 7,000 ft 6,500 - 10,000 ft
H Idle speed Approx. 1,550 rlmin t t t
Clutch engagement Approx. 4,000 r/min 4,100 rlmin 4,200 r/min t
El Main jet #151.3 (STD)
El Gearing 23/39 (70L) 22/39 (70L) 21/39 (68L) 20139 (68L)
Primary spring
Color W-S-W t t t
rn Length 81.0 m m t t t
Preload rate 35 kg - 2.25 kglmm t t t
@! Outside diameter 059.0 m m t t t
fl Weight (1D) 8CR t t t
Weight rivet Steel 10.3 (OUT) Steel 10.3 (OUT) Aluminum 10.3 (OUT) Aluminum 10.3 (OUT)
Steel 17.2 (IN) Steel 10.3 (IN) Steel 10.3 (IN) Aluminum 10.3 (IN)
fl Secondary spring
Color R t t t
&! Length 75 m m t t t
t t t
729 kgmmlrad
Sec. torque cam 47" t t t
Sec. clutch shim 1.0 m m t t t
Setting chart Model: VXGOOXTR
CLUTCH mlINSP

(Rivet position: OUTER / INNER)
Oft ..............................................
Production
Weight : 8CR
Rivet : Steel 10.3 / Steel 17.2
Primacy spring : 35 kg-2.25 kg/mm
Roller : 015.6
Torque cam : 47"
3,000 ft - - - - .............................................
(900 rn)
3,500 ft - - - - - - - - - Weight : 8CR ....................
(1,000 m) Rivet : Steel 10.3 / Steel 10.3
Roller : 015.6
4,500 ft -- -- - - - - Sec. Preload : 60" (3-3) ....................
(1,400 rn) Torque cam : 47"
5,000 ft . . . . V
. .I. .A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(1,500 m) Weight : 8CR
Rivet : Aluminum 10.3 /Steel 10.3
Roller : 015.6
Torque cam : 47"
6,500 ft ----------------------------------------
(2,000 rn)
7,000 ft . . . . . . . .V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(2,100 m)
Weight : 8CR
Rivet : Aluminum 10.3 1 Aluminum 10.3
Primary spring : 35 kg-2.25 kglmrn
Roller : 015.6
Torque cam : 47"
10,000 ft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(3,000 m)
V
*
Specifications Model: VXGOOSX
Elevation - 3,500 ft/1,000 m 3,000 - 5,000 ft 4,500 - 7,000 ft 6,500 - 10,000 ft

Idle speed Approx. 1,550 rlmin t t t
Clutch engagement Approx. 3,900 rlmin t 4,000 rlmin 4,200 r/min
• Main jet # I 51.3 (STD)
ldle mixture screw 1-1.2 (STD)
!ElGearing 22/39 (70L) t 21/39 (68L) 20139 (68L)
Primary spring
Dl Color W-S-W P
t t t
Length 81.0 m m t t t
Preload rate 35 kg - 2.25 kglmm t t t
Wire diameter $5.5 m m t t t
Outside diameter $59.0 m m t t t
Weight (ID) 8AB t t t
!?IWeight rivet Steel 13.9 (OUT) Steel 10.3 (OUT) Aluminum 10.3 (OUT) Aluminum 10.3 (OUT)
Steel 13.9 (IN) Steel 13.3 (IN) Steel 13.3 (IN) Aluminum 10.3 (IN)
Roller outer dia. $15.0 m m t t t
Roller bushing Duralon t t c
Secondary spring
Color G t t t
Length 75 m m t t t
Preload rate 40" (1-3) 50" (2-3) 60" (3-3)
t
848 kgmmlrad t t
Wire diameter $5.5 m m t t t
Outside diameter $69.5 m m t t c
Sec. torque cam 43" t t c
Setting chart Model: VXGOOSX
Elevation , Clutch setting Remark

Oft ..............................................
Production
Weight : 8AB
Roller : 015.0
Torque cam : 43"
3,000 ft
(900 m)
3,500 ft Weight : 8AB --------------.
Roller : 015.0
Gearing : 22/39 (7OLINKS)
4,500 ft -- -- Sec. Preload : 40" (1-3) --------------.
(1,400 m) Torque cam : 43"
5,000 ft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(1,500 m) Weight : 8AB
Rivet : Aluminum 10.3 /Steel 13.3
Roller : 015.0
Torque cam : 43"
6,500 ft ..........................................
(2,000 m)
7,000 ft - - - - - -
V- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
(2,100 m)
Weight : 8AB
Rivet : Aluminum 10.3 /Aluminum 10.3
Roller : 015.0
Torque cam : 43"
10,000 ft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(3,000 m)
v
Specifications Model: VX700XT / VX7OOXTC
El Elevation - 3,500 W1,000 m 3,000 - 5,000 f? 4,500 - 7,000 f? 6,500 - 10,000 ft

• Idle speed Approx. 1,600 rlmin t t t
Clutch engagement Approx. 4,000 r/min t t t
Shift speed Approx. 8,300 r/min t t t
Main jet # I : # I 45
#2, #3: 143.8 (STD)
Pilot (slow) jet #45 (STD)
LJ See MAINTENANCE SPECIFICATIONS (High altitude settings)
Gearing 23/40 (70L) t t 22/40 (70L)
D l Primary spring
Color W-S-W G-P-G P t
Length 81.0 m m 76.3 m m 75.4 m m t
Preload rate 35 kg - 2.25 kg/mm 30 kg - 2.75 kg/mm 30 kg - 3.0 kglmm t
Wire diameter 05.5 m m 05.8 m m 06.0 m m t
Outside diameter 060.0 m m 059.6 m m 060.0 m m t
Weight (ID) 8CH-00 t t t
Weight rivet Steel 13.9 (OUT) Steel 10.3 (OUT) Aluminum 10.3 (OUT) None (OUT)
Steel 13.9 (IN) Steel 13.9 (IN) Steel 13.9 (IN) Steel 13.3 (IN)
7

H Roller bushing Duralon t t t
Secondary spring
Color G t R t
Length 75 m m t t t
Preload rate 60" (3-3) 60" (3-3)
t t
848 kgmmlrad 729 kgmmlrad
Wire diameter 05.5 m m t 05.3 m m t
li5] Sec. clutch shim 1.0 m m t t t
Setting chart Model: VX7OOXT 1 VX700XTC

Oft ---------------------------------------------.
Production
Weight : 8CH-00
Roller : 014.5
Torque cam : 45"
3,000 ft
(900 m)
3,500 ft Weight : 8CH-00 -----------------.
Roller : 014.5
4,500 ft Sec. Preload : 60" (3-3) ------------------
(1,400 m) Torque cam : 45"
5,000 ft - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
(1,500 m) Weight : 8CH-00
Rivet : Aluminum 10.3 1 Steel 13.9
Roller : 014.5
Torque cam : 45"
6,500 ft ..........................................
(2,000 m)
7,000 ft - - - - - -V
-------------------------------------------.
(2,100 m)
Weight : 8CH-00
Rivet : None l Steel 13.3
Primary spring : 30 kg-3.0 kgtmm
Roller : 014.5 (8CA-91)
Torque cam : 45"
10,000 ft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(3,000 m)
v
Iw I White
L
I S ( Silver I L I Blue 1
P Pink R Red 0 Orange
Y Yellow G Green
Specifications Model: VX700XTCD
El Elevation - 3,500 ft/1,000 m 3,000 - 5,000 ft 4,500 - 7,000 ft 6,500 - 10,000 ft

Clutch engagement Approx. 4,000 rlmin t t t
H Main jet # I : # I 45
#2, #3: 143.8 (STD)
Pilot (slow) jet See MAINTENANCE SPECIFICATIONS (High altitude settings)
#45 (STD)
Gearing 22/39 (70L) t t 21/39 (68L)
El Primary spring
Dl Color W-S-W G-P-G P 0-P-0
Length 81.0 m m 76.3 m m 75.4 m m 76.4 m m
Preload rate 35 kg - 2.25 kglmm 30 kg - 2.75 kglmm 30 kg - 3.0 kg/mm 30 kg - 3.25 kg/mm
Wire diameter 05.5 mrn 05.8 m m 06.0 m m t
Weight (1D) 8CH-00 t t t
Steel 13.9 (IN) Steel 13.9 (IN) ' Steel 13.9 (IN) Steel 13.9 (IN)
Secondary spring
Color G t R t
@d Length 75 m m t t t
Preload rate 60" (3-3) 60" (3-3)
t t
-
-
Ihj Sec. clutch shim 1.0 m m t t t
*
Setting chart Model: VX700XTCD

Oft ..............................................
Production
Weight : 8CH-00
Rivet : Steel 13.9 /Steel 13.9
Roller : 014.5
Torque cam : 45"
3,000 f t - - - - --------------------------------------------.
(900 m)
3,500 ft - - - - - - - - - Weight : 8CH-00 ------------------
( 1,000 m) Rivet : Steel 13.9 / Steel 13.9
Roller : 014.5
4,500 ft -- -- ---- Sec. Preload : 60" (3-3) ------------------
(1,400 m) Torque cam : 45"
5,000 ft . . . . V
. .I. .A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(1,500 m) Weight : 8CH-00
Rivet : Aluminum 10.3 / Steel 13.9
Roller : 014.5
Torque cam : 45"
6,500 ft ..........................................
(2,000 m)
7,000 ft - - - - - -V- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - .
(2,100 m)
Weight : 8CH-00
Rivet : None / Steel 13.9
Roller : 014.5 (8CA-91)
Torque cam : 45"
10,000 ft - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - .
(3,000 m)
v
Specifications Model: VX700XTCP

H Idle speed Approx. 1,600 r/min t t t
fl Clutch engagement Approx. 4,000 rlmin t t t
Shift speed Approx. 8,300 r/min t t t
El Main jet #I: #I45
#2, #3: 143.8 (STD)
Pilot (slow) jet See MAINTENANCE SPECIFICATIONS (High altitude settings)
#45 (STD)
Gearing t
- 22/40 (70L) t 21/40 (70L) *20/40 (68L)
Dl Primary spring
Color G-P-G t t P
rn Length 76.3 m m t t 75.4 m m
Preload rate 30 kg - 2.75 kglmm t t 30 kg - 3.0 kglmm
Wire diameter 05.8 m m t t 06.0 m m
Outside diameter 059.6 m m c t 060.0 m m
Weight (ID) 8CH-00 c 8CR t
H Weight rivet Steel 13.9 (OUT) Steel 10.3 (OUT) Aluminum 10.3 (OUT) None (OUT)
Roller outer dia. 014.5 m m t t c
fl Pri. clutch shim None t t t
Secondary spring
Color G t t t
Length 75 m m t t t
t t t
848 kgmmlrad
Outside diameter 069.5 m m t t c
Sec. torque cam 45" c 43" t
Sec. clutch shim 1.0 m m t t t
*E
l More than 9,500 ft
Setting chart Model: VX7OOXTCP

Oft ---------------------------------------------.
Production
Weight : 8CH-00
Roller : 014.5
Torque cam : 45"
*I*
3,000 ft - .............................................
(900 rn)
3,500 ft ---- - - - - - Weight : 8CH-00 ------------------
( 1,000 m) Rivet : Steel 10.3 / Steel 13.9
Primary spring : 30 kg-2.75 kglrnm
Roller : 014.5
4,500 ft -- -- --- *
Sec. Preload : 60" (3-3) ------------------
(1,400 m) Torque cam : 45"
5,000 ft - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - .
(1,500 m) Weight : 8CR
Roller : 014.5
Torque cam : 43"
6,500 ft ..........................................
(2,000 m)
7,000 ft . . . . . . . .V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(2,100 m)
Weight : 8CR
Roller : 014.5 (8CA-91)
Torque cam : 43"
9,500 ft - - - - - - - - .........................................
(2,900 m) AWeight : 8CR
Rivet : None ISteel 10.3
10,000 ft --- ,_ -
, Primary spring : 30 kg-3.0 kglmm ------------------
(3,000 rn) Roller : 014.5 (8CA-91)
Gearing : 20140 (68L)
Torque cam : 43"
Specifications Model: VX7OOSXS

Idle speed Approx. 1,600 r/min t t t
Clutch engagement Approx. 4,000 r/min t t t
Main jet #1: #I45
#2, #3: 143.8 (STD)
Pilot (slow) jet #45 (STD) [HI See MAINTENANCE SPECIFICATIONS (High altitude settings)
Gearing 23/40 (70L) t t 22/40 (70L)
El Primary spring
Dl Color W-S-W G-P-G P c
rn Length 81.0 m m 76.3 m m 75.4 m m c
Preload rate 35 kg - 2.25 kglmm 30 kg - 2.75 kglmm 30 kg - 3.0 kglmm t
Wire diameter 85.5 m m 85.8 m m 86.0 m m t
Weight (1D) 8CH-00 t t c
Roller outer dia. 814.5 m m t t c
Secondary spring
El Color G t R t
@! Length 75 m m t t t
Preload rate 60" (3-3) 60" (3-3)
t t
Setting chart Model: VX7OOSXS

Oft ..............................................
Production
Weight : 8CH-00
Roller : 014.5
Torque cam : 45"
3,000 ft - --------------------------------------------.
(900 m)
3,500 ft - - - - - - - - - Weight : 8CH-00 -----------------.
Primary spring : 30 kg-2.75 kglmrn
Roller : 014.5
4,500 ft -- -- ---- Sec. Preload : 60" (3-3) ------------------
(1,400 m) Torque cam : 45"
5,000 ft - - - -.
-I-1-------------------------------------------.
(1,500 m) Weight : 8CH-00
Roller : 014.5
Torque cam : 45"
6,500 ft ----------------------------------------
(2,000 m)
7,000 ft . . . . . . . .V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(2,100 m)
Weight : 8CH-00
Roller : 014.5 (8CA-91)
Torque cam : 45"
10,000 f t - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - .
(3,000 m)
v
W White S Silver L Blue
P Pink 0 Orange
Y Yellow G Green
Specifications Model: VT700
Elevation - 3,500 ft/1,000 m 3,000 - 5,000 ft 4,500 - 7,000 ft 6,500 - 10,000 ft

Clutch engagement Approx. 3,900 rlmin t t c
• Main jet #I: #I45
#2, #3: 143.8 (STD)
Pilot (slow) jet #45 (STD) IdSee MAINTENANCE SPECIFICATIONS (High altitude settings)
Gearing 22/39 (70L) 21/39 (68L) 20139 (68L) 19/39 (68L)
D l Primary spring
Color P 0-P-0 t c
Length 75.4 m m 76.4 m m t c
Preload rate 30 kg - 3.0 kg/mm 30 kg - 3.25 kgjmm t t
Outside diameter 060.0 m m t t c
Weight (1D) 8CH-00 t 8CR c
H Weight rivet Steel 13.9 (OUT) Steel 10.3 (OUT) Aluminum 10.3 (OUT) None (OUT)
@lWeight bushing Duralon t t t
H Roller bushing Duralon t t t
Secondary spring
@IColor G t t c
Length 75 m m c t t
t t t
848 kgmmlrad
-
[H1 Sec. clutch shim 1.0 m m t c t

Setting chart Model: W O O

0 ft .............................................
Production
Weight : 8CH-00
Rivet : Steel 13.9 /Steel 17.2
Roller : 014.5
Gearing : 22/39 (7OLINKS)
Torque cam : 45"
3,000 ft - - - - ............................... - - - - - - - - - - __ _ _
(900 m )
3,500 ft - - - - - - - - - Weight : 8CH-00 --------------____
(1,000 m ) Rivet : Aluminum 10.3 /Steel 10.3
Roller : 014.5
4,500 ft -- -- ---- Sec. Preload : 70" (1-6) -------------_____
(1,400 m ) Torque cam : 45"
5,000 ft . . . .I
. . .1
..........................................
(1,500 m ) Weight : 8CR
Rivet : Aluminum 10.3 1 Steel 13.3
Roller : 014.5
Torque cam : 45"
6,500ft -----------------------------------------.
(2,000m)
7,000 fi . . . . . . . .V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(2,100m)
Weight : 8CR
Primary spring . : 30 kg-3.25 kg/mm
Roller : 0 14.5 (8CA-9 1)
Torque cam : 45"
10,000fi-------------------------------1----------------.
(3,000m)
v
2
2E331
The clutch m a y require tuning depending upon
the area of operation and desired handling char-
acteristics. The clutch can be tuned by changing
engagement and shifting speed. Clutch engage-
ment speed is defined as the engine speed where
the machine first begins t o move f r o m a complete
stop.
Shifting speed is when the machine has been
started at full-throttle from a dead stop and has
- -
travelled 200 300m (650 1,000 ft).
Normally, when a machine reachesshifting speed,
the vehicle speed increases but the engine speed
remains nearly constant. Under unfavorable con-
ditions (wet snow, icy snow, hills, o r rough ter-
rain), however, engine speed m a y decrease after
the shifting speed has been reached.
R Engine speed
Good condition
Bad condition
Clutch shifting speed
El Clutch engagement speed
F
J Starting position
lJ 200
G - 300 m (650 - 1,000 ft)
Distance travelled
GEAR SELECTION 1-1 ADJ
GEAR SELECTION
The reduction ratio of the driven gear to the drive
gear must be set according to the snow condi-
tions. If there are many rough surfaces or
unfavorable snow conditions, the driveldriven
gear ratio should be increased. If the surfaces are
fairly smooth or better snow conditions exist,
decrease the ratio.
Gear ratio chart

The following drive and driven gears and chains
are available as options. The figures i n the upper
lines represent the driveldriven gear ratios, while
the number on the following line, followed by an
"L", designates the number of chain links.
NOTE:
Do not set the gearing to any of the indicated (x)
settings.
GEAR SELECTION ml INSP 0
@ Chain and sprocket parts number:

Parts name Teeth&Links Parts No. rn Standard
18T 89J-17682-80
19T 89J-17682-90
20T 89J-17682-00
Drive sprocket
21T 89J-17682-10
22T 89J-17682-20 VX500XTR, VX7OOXTCDIXTCP
23T 89J-17682-30 VX6OOXTR, VX700XT/XTC/SXS
39T 89J-47587-90 500,600, VX7OOXTCD, VT700
Driven sprocket 40T 89J-47587-00 VX70OXT/XTC/XTCP/SXS
39T (REVERSE) 8CW-47587-90
68LINKS 94860-02068
Chain (links)
7OLINKS 94860-02070 500,600,700
@ Gear ratio
* Not for reverse models
@ Secondary spring
Spring rate
lWire gauge
P
J Parts No. Nemmlrad a No. of coils &d Color
(mm)
Free length
(mm)
Standard
(kgmmlrad)
90508-500B1 6003 (613) 5.2 BROWN 5.0 75
90508-536A9 7 147 (729) 5.5 RED 5.3 75 500, VXGOOXTR
90508-556A2 8314 (848) 5.5 GREEN 5.5 75 VXsooSX, M700, VX700XTIxTclxTCDIxTCPlSXS
@ Secondary spring twist angle

90508-536A9 (RED) / 90508-556A2 (GREEN) / 90508-500B1 (BROWN)
@ Torque cam (secondary spring seat)

El Parts No. QI Cam angle rn Standard
8BV-17604-30 43" VX6OOSX
8BV-17604-50 45" 500, VX700XTIXTCIXTCDIXTCP/SXS, WO
O
8BV-17604-70 47" VX6OOXTR
L
GEAR SELECTION 1- AD J
@ Primary spring
a El
IEl a
• Spring rate El Wire Outside
No. of
Free
Standard
Preload
Parts No. Nlmm Color gauge diameter length
(kg) coils
(kglrnrn) (mm) (rnm) (mm)
90501-550J 8 22.5(2.25) 30.0 W-P-W 5.5 60.0 4.62 78.7 500
90501-555J 9 22.5(2.25) 35.0 W-S-W 5.5 59.0 4.66 81.0 "1
90501-582J 1 25(2.5) 30.0 Y-P-Y 5.8 60.0 4.96 77.4
90501-585J 3 27.5(2.75) 30.0 G-P-G 5.8 59.6 4.64 76.3
90501-602J 0 30(3.0) 30.0 P 6.0 60.0 4.74 75.4 W O O
90501-605J 5 32.5(3.25) 30.0 0-P-O 6.0 60.0 4.53 74.6
FRONT SUSPENSION 1-1 ADJ
FRONT SUSPENSION
Spring preload
1. Adjust:
Spring preload (VX500XTR, VXGOOXTR,
VX7OOXT, VT700)
Adjustment steps:
Turn the adjusting ring @ to the proper
position.
Spring adjuster
1 2 3 4 5
position
Preload Softer t Harder
1 (VX500XTR, VXGOOXTR, VX7OOXT)
Standard
2 (moo)
Be sure that the left and right spring preload is

the same.
Spring preload (VXGOOSX, VX700XTCl

XTCDIXTCPISXS
Adjustment steps:
Turn the spring seat @ in or out.
Spring seat Standard

distance Shorter t + Longer
Preload Harder t -+ Softer
Max. Min.
@ Length 243 mm 253 mm 263 mm
NXIWmmllXCs' (10.35 in)
(9.57 in) (9.96 in)
Max. Min.
(VX600sX) 8.39 i n (8.78 in) (9.17 in)
Max. Min.
(VX700SXS) 7.72 i n (8.31 in) (8.62 in)
Be sure that the left and right spring preload is

the same.
This shock absorber contains highly pressur-

ized nitrogen gas.
Do not tamper with or attempt t o open the
shock absorber assembly.
Do not subject theshock absorber assembly to
an open flame or high temperature, as this
-79- could cause it t o explode.
FRONT SUSPENSIONIREAR SUSPENSION 1- ADJ
Damping force (VX7OOSXS)
1.Adjust:
Damping force
Adjustment steps:
Turn the adjusting knob @ in or out.
Minimum (hard) 1 Clicks out*
*:From the fully turned-in position
Never attempt t o turn an adjuster beyond

the maximum or minimum setting.
Be sure the left and right damping force is
the same.
REAR SUSPENSION
Stopper band
1. Adjust:
Stopper band tension
NOTE:
This adjustment affects the handling characteris-
tics of the machine.
Adjustment steps:
Loosen the locknut @.
Turn the adjusting nut @ in or out to adjust
the stopper band tension.
Adjuster Longer t -+ Shorter

Thread maximum minimum
length @ 10 mm (0.39 in)
VX500XTR,
VXGOOXTRISX,
VX700XT
25 mm (0.98 in)
VX7OOXTCIXTCDl
XTCPISXS, W O O
Effects More weight Less weight on

on skis. Less skis. More
weight weight
transfer transfer
Tighten the locknut @.

-30-
REAR SUSPENSION
Spring preload
ml INSP 0
1. Adjust:
Spring preload (VX500XTR, VXGOOXTR,
VX7OOXT, VT700)
Adjustment steps:
Turn the adjusting ring @ t o the proper
position.
Spring adjuster
1 2 3 4 5
position
Preload Softer t + Harder
1 (VX7OOXT)
ElStandard
(front) 2 (VX500XTR, VXGOOXTR)
3 (VT700)
Spring adjuster
position
,
Preload Softer t + Harder
Standard 1(VX500XTR, VXGOOXTR)
(rear) 2 (VX7OOXT)
4 CvnOO)
Spring preload (VXGOOSX, VX700XTC/

XTCD/XTCP/SXS)
Adjustment steps:
Turn the spring seat @ in or out.
Spring seat Standard

distance Shorter t + Longer
Preload Harder t + Softer
El Length @ Max. Min.
(front)
210 mm 220 mm 230 mm
(VX700XTC' (8.27 in) (8.66 in) (9.06 in)
XTCDIXTCP)
El Length @I Max. Min.
(front) 173 mm 183 mm 192 mm
(VXGOOSX) (6.81 in) (7.20 in) (7.55 in)
E
l Length @ Max. Min.
(front) 175 mm 185mm 195 mm
(VX7OOSXS) (6.89 in) (7.28 in) (7.68 in)
El Length @ Max. Min.

(rear)
358.5 mm 368.5 mm 378.5 mm
(VX700XTC1 (14.11 in) (14.51 in) (14.90 in)
XTCDIXTCP)
Length @
Max. Min.
(rear)
298mm 308mm 318mm
(VX700SXS) (11.73 i n (12.13 in) (12.52 in)
(vx6oosx)
REAR SUSPENSION
(IAD
NSPI1J
This shock absorber contains highly pressur-

ized nitrogen gas.
Do not tamper with or attempt to open the
shock absorber assembly.
Do not subject theshock absorber assembly to
an open flame or high heat, which could cause
it to explode.
CHASSIS
SKI (VX7OOXTCP)
: 10 Nrn (1.0 rn kg, 7.2 ft lb) 1

: 21 Nrn (2.1 rn kg, 15 ft 1b)-
:148 Nrn (4.8 rn kg, 35 ft Ib)
-,:ESSO beacon 325
grease or Aeroshell
grease #7A
Order Job name/Part name Q'tY Remarks

Ski removal Remove the parts in the order below.
1 Cotter pin 1
2 Ski column lower bracket 1
3 Ski stopper 1
4 Collar 1
5 Washers 6
6 Ski 1
7 Ski runner 1
8 Washers 6
9 Ski handle 1
For installation, reverse the removal proce-
dure.
SKI/FRONT SUSPENSION
INSPECTION
m+(
1. Inspect:
Ski @
Ski runner @
Ski column lower bracket @
Ski handle @
Ski stopper @
Wear/cracks/damage + Replace.
Mounting bolt @
Collar @
Weaddamage + Replace.
FRONT SUSPENSION
HANDLING NOTES
VX700XTC/XTCD/XTCP/SXS
This shock absorber contains highly compressed

nitrogen gas. Before handling the shock absorber
read and make sure that you understand the
following information. The manufacturer cannot
be held responsible for property damage or per-
sonal injury that may result from improper han-
dling.
Do not tamper or attempt t o open the gas
chamber.
Do not subject the shock absorber to an open
flame or any other source of high heat. This
may cause the unit t o explode due t o excessive
gas pressure.
Do not deform or damage the gas chamber in
any way. Gas chamber damage will result in
poor damping performance.
f RONT SUSPENSION ICHASI +I
INSTALLATION
I . Install:
Control rod @
G$Ff Nut @
Joint @
@Set length
2. Install:
Steering arm @
NOTE:
Align the punch mark @ on the ski column with
the punch mark @ on the steering arm.
1 % Nut (steering arm):

54Nm(5.4rn0kg,38ft*Ibl
PRIMARY SHEAVE 1-
POWER TRAIN
PRIMARY SHEAVE
: 6 Nm (0.6 rn kg, 4.3 f? Ib)

: 14 Nm (1.4 r n kg, 10 ft Ib)
m: 200Nm(20rn*kg, 1 4 5 f l * I b ) I
Order Job name/Part name Q"Y Remarks

Primary sheave disassembly Disassemble the parts in the order below.
@ Primary sheave cap 1
@ Primary sheave spring 1
@ Collars 3
@ Rollers 3
@ Washers 6
@ Collars 3
@ Weights 3
@ Washers 6
@ Fixed sheave 1
@ Starter motor driven gear 1 (VX500XTR, VX600XTR, VX700XTCD, VT700)
@ IStopper 1
@ Sliding sheave 1
@ Bushing 1
@ Spider 1
Q Sliders 6
For assembly, reverse the disassembly pro-
cedure.
SECONDARY SHEAVE M I
SECONDARY SHEAVE
ASSEMBLY
1. Install:
Secondary sheave spring @
NOTE:
Hookthe end ofthe secondarysheave spring onto
the spring holes in the fixed sheave and in the
spring seat.
Standard spring position:

2-6 (VX500XTR)
3-3 (VX6OOXTR)
3-3 (VX7OOXT/XTC/XTCD/XTCP/SXS)
1-3 (VX6OOSX)
1-6 (VT700)
Installation steps:
Attach the sheave compressor.
Turn the sliding sheave counterclockwise to
the specified angle @.
Hold the sliding sheave and fixed sheave in
this position.
Standard twist angle @:

80" (VX500XTR)
60" (VX600XTR)
60" (VX7OOXT/XTC/XTCD/XTCP/SXS)
40" (VX6OOSX)
70" (VT700)
@ = (sheave side hole number + spring seat

side hole number) x 10
Turn in the sheave compressor screw so that

the spring seat engageswith the fixed sheave.
DRIVE CHAIN HOUSING I I I
POWR
TR
DRIVE CHAIN HOUSING
WITHOUT REVERSE MODEL
: 10 Nm (1.0 m kg, 7.2 ft lb) 1

: 24 Nm (2.4 m kg, 17 ft Ib)
0: 48 Nm (4.8 m kg, 35 ft Ib)
: 60 Nm (6.0 m kg, 43 ft Ib)
Order Job name/Part name Q'W Remarks

Drive chain housing removal Remove the parts i n the order below.
Brake caliper Refer to "BRAKE".
Parking brake
Tension adjuster Loosen. Referto "SLIDE RAILSUSPENSION".
I Bolt I Oil drain.
2 Drive chain housing cover 1
3 Chain tensioner I
4 Roller 1
5 Drive sprocket 1
6 Collar 1
7 Drive chain 1
8 Driven sprocket 1
9 Collar 1
10 Drive chain housing 1
dure.
DRIVE CHAIN HOUSING IPOWR1
3
1
TR
INSTALLATION
During installation, pay attention to the following
point:
Make sure that the bearing seals face towards

the drive chain, as shown.
Properly install the rubber seal onto the drive

chain housing, making sure that these are no
gaps.
Be sure to install the spacers in their original

positions of the brake disc and jackshaft will
stick.
- -
@I 0.1 0.5 m m (0.004 0.020 in)
-: ESSO beacon 325 grease or Aeroshell

grease #7A
DRIVE CHAIN HOUSING rl
POWR
DRIVE CHAIN HOUSING AND JACKSHAFT

INSTALLATION
1. Install:
8 Drive chain housing
Jackshaft
Installation steps:
Install the drive chain housing a.
Tighten the bolts @.
Bolt (drive chain housing):

48 Nm (4.8 m kg. 35 ft lb)
Temporarily tighten the nuts @.

Tighten the nuts @.
Nut (jackshaft):
60 N m (6.0 m kg, 43 ft Ib)
?
8 Retighten the nuts @.
Nut (bearing holder):

b? 23 N m (2.3 m kg, I7 ft lb)
8 Tighten the set screws @.
Set screw (bearing):

b% 8 Nm (0.8 rn kg, 5.8 ft lb)
8 Install the drive chain housing cover @.

Tighten the bolts @.
Bolt (drive chain housing cover):

24 Nrn l2.4 m kg. 17 ft lb)
DRIVE CHAIN HOUSING 1-
WITH REVERSE MODEL
: 10 Nm (1.0 m kg, 7.2 ft Ib)

: 24 Nm (2.4 m kg, 17 ft Ib)
: 48 Nm (4.8 m kg, 35 ft Ib)
: 60 Nm (6.0 rn kg, 43 ft Ib)
Order Job nameIPart name Q'W Remarks

Drive chain housing removal Remove the parts in the order below.
Battev
Battery bracket
Brake caliper Refer to "BRAKE".
Parking brake
Tension adjuster Loosen. Referto "SLIDE RAILSUSPENSION".
1 Joints 2
2 Shift rod 1
3 Shift lever assembly 1
4 Lever 1
5 Joints 2
6 Lever rod 1
7 Bolt 1 Oil drain.
8 Drive chain housing cover 1
9 Washer 1
Order Job name/Part name
DRIVE CHAIN HOUSING
Qyt'
r
l
Remarks
POWR
10 Reverse drive gear 1

I1 Spring 1
12 Chain tensioner 1
13 Roller 1
14 Collar 1
15 Spring 1
16 Journal 1
17 Reverse driven gear 1
18 Washer 1
19 Forward driven sprocket 1
20 Collar 1
21 Counter gear 1
22 Drive sprocket 1
23 Drive chain 1
24 Collar 1
25 Washer 1
26 Plate 1
27 Shaft 1
28 Drive chain housing 1
dure.
DRIVE CHAIN HOUSING
al
mPOWR
INSTALLATION
During installation, pay attention t o t h e following
point:
FiI Properly install the rubber seal onto the drive

chain housing, making sure that these are no
gaps-
IBI Make sure that the bearing seals face towards

the drive chain, as shown.
Z
IJ Be sure to install the spacers in their original
positions of the brake disc and jackshaft will
stick.
0.1 - 0.5 m m (0.004 - 0.020 in)

-: ESSO beacon 325 grease or Aeroshell
grease #7A
Drive chain housing a n d jackshaft installation

steps Referto the "WITH OUTREVERSE MODEL".
BRAKE
BRAKE
Order Job name1Part name Q'~Y Remarks

Brake caliper disassembly Disassembly the parts in the order below.
@ Cap bolt 1
@ Retaining pin 1
Pad spring 1
@ Brake pads 2
@ Shim 1 2
@ Shim 2 2
a Bleed screws 2
@ Oil seals 4
@ Pistons 2
cedure.
SLIDE RAlL SUSPENSION K-
l1
POWR
SLIDE RAlL SUSPENSION

VXGOOSX, VX7OOSXS
:171 Nm (7.1 m kg. 51 ft lb)]
Order Job name/Part name Q'tY Remarks

Slide rail suspension removal Remove the parts in the order below.
Tension adjuster Loosen.
1 Blind caps 2
2 Bolts 6
3 Washer 2
4 Slide rail suspension 1
dure.
I
SLIDE RAIL SUSPENSION
: 24 Nm (2.4 m kg, 17 ft Ib)

: 71 Nm (7.1 m kg, 51 ft lb)
Order Job name/Part name Q

yt' Remarks
Slide rail suspension removal Remove the parts in the order below.
Tension adjuster Loosen.
1 Blind caps 2
2 Suspension rear plate 2
3 Bolts 10 Install the MMGOOP and MM7OOP boltsm into
the lower set of holes [hl.
4 Slide rail suspension 1
dure.
7
:'4 Nm (0.4 m kg, 2.9 ft Ib)

m: 1 5 N m ( 1 . 5 m * k g , l l f t * I b )
: 30 Nm (3.0 m kg, 22 ft Ib)
: 49 Nm (4.9 m kg, 35 ft Ib)
: 71 Nm (7.1 m kg, 50 ft Ib)
: 24 Nm (2.4 m kg, 17 ft Ib)
Order Job name/Part name Q

yt' Remarks
Slide rail suspension disassembly Disassemble the parts in the order below.
@ Stopper bands 2
@ Hooks 2
@ Bushings 4
@ Collars 2
@ Front shock absorber 1
@ Rubber damper 2 (VXGOOSX, VX7OOSXS)
@ Front suspension bracket 1
@ Front pivot arm 1
@ Bracket 2 (VXGOOSX, VX7OOSXS)
@ Bushings 2
Shaft 1
@ Bushings 4
@ICollars 2
@ Suspension wheels 2
@ Collar 2
@ Wheel brackets 2
@ Front pivot arm brackets 2
@ Shaft 1 (Vl-700)
1-
: 24 Nm (2.4 m kg, 17 ft Ib)

: 49 Nm (4.9 r n kg, 35 ft Ib)
: 71 Nm (7.1 m kg, 50 ft Ib)
Order Job nameIPart name Q'~Y Remarks

@ Collar 2
@ Wheel brackets 2
@ Circlips 2
@ Bushings 2
@ Shaft 1
@ Rear suspension bracket 1
@ Spacers 2
@ Bushings 2
@ Collar 1
SLIDE RAIL SUSPENSION 1 -POWR
:149 Nm (4.9 m kg, 35 ft Ib)
m : 1 7 1 Nm (7.1 m okg, 5 0 f t 0Ib)
Order Job name/Part name Q'W Remarks

@ Rear shock absorber 1
O, Bushings 2
@ Collar 1
@ Pull rod 2
@ Collars 4
@ Bushings 4
@ Rear brackets 2 (VT700)
@ Collars 2 (VT700)
@ Collars 2 (VXGOOSX, VX7OOSXS)
@ Control rods 2
@ Bushings 2
@ Collars 2
@ Bushings 2
SLIDE RAIL SUSPENSION 1-
.
-I
1 : 24 N m (2.4 rn kg, 17 ft [b)
1 : 71 N m (7.1 rn kg, 50 ft lb)
: 75 N m (7.5 m kg, 54 ft lb)
Order Job name/Part name Q'ty Remarks

@ Rear pivot arm 1
@ Bushings 2
@ Collar 1
@ Collar 1
@ Rear pivot arm bracket 1
@ Collar 1
@ Circlips 2
@ Wheel bracket 1
@ Rear axle 1
@ Guide wheels 3
@ Collars 2
@ Tension adjusters 2
@ Collar 1
@ Collar 1
@ Sliding frames 2
Collar 1
cedure.
.
POWR
FRONT AXLE AND TRACK
FRONT AXLE AND TRACK
INSTALLATION
Reverse the "REMOVAL" procedure.
Note the following points.
1. Install:
Sprocket wheels
Guide wheels
NOTE:
When pressing the sprocket wheels onto the
front axle, align the lugs on each sprocketwheel.
Locateeach sprocketwheel and guide wheel on
the axle where shown in the illustration.
: VX500XTR
: VXGOOXTR, VT700
: VXGOOSX, VX7OOSXS
: VX700XT/XTC/XTCD/XTCP
2. Place the track in the chassis.
NOTE:
Be sure it is positioned as shown in the illustra-
tion.
TURNING DIRECTION
-51-
ENGINE
ENGlNE ASSEMBLY ml
ENGINE ASSEMBLY
500/600
:123 Nm (2.3m kg, 17 ft lb) 1

El:
El:
\ /
\
\ 1
\I
Order Job name/Part name Q't y Remarks

Engine removal Remove the parts in the order below.
Battery negative lead (VX500XTR, VXGOOXTR)
Exhaust pipe
Carburetor Refer to "CARBURETOR".
Recoil starter Refer to "RECOIL STARTER".
Water pump Refer to "WATER PUMP AND THERMO-
STATIC VALVE".
Primary sheave Refer to "PRIMARY SHEAVE AND DRIVE V-
BELT".
1 Coolant hose 1
2 Oil hoses 2
3 Oil pump cable 1
4 Vacuum hose 1
5 CDI magneto couplers 2
6 Thermo sensor coupler 1
7 Spark plug caps 2
8 Starter motor 1 (VX500XTR, VX6OOXTR)
9 Engine assembly 1
dure.
ENGINE ASSEMBLY ml
: 23 Nrn (2.3 rn kg, 17 ft Ib)
B: 60Nrn(6.0rn0kg,43ft*lb)'
: 90 Nrn (9.0 rn kg, 65 ft Ib)
.
Order Job name1Pa1-tname Q'ty Remarks
Engine removal Remove the parts in the order below.
Exhaust pipe
Carburetor Refer to "CARBURETOR".
Recoil starter Refer to "RECOIL STARTER".
CDI Magneto rotor Refer to "CDI MAGNETO".
Frame cross member
Primary sheave Refer t o "PRIMARY SHEAVE AND DRIVE V-
BELT".
Coolant Drain. Refer to "COOLANT REPLACEMENT".
1 Coolant hose 1 1
2 Coolant hose 2 1
3 Thermo sensor coupler 1
4 CDI magneto couplers 2
5 Rear bracket right 1
6 Oil pump cable 1
7 Oil hoses 2
8 Vacuum hose 1
9 Starter motor 1 (VX7OOXTCD, Vr700)
10 Engine assembly 1
dure.
CARBURETION
CARBURETORS mi
CARBURETORS
500/600
\1
* Intake silencer
First, remove the throttle cable from the cable guide on the steering column.
Adjust the throttle cable free play while the cable is i n the cable guide.
After adjusting the throttle cable free play, properly install the upper and lower intake silencer
plates and seal.
Order Job nameIPart name Q'W Remarks

Carburetors removal Remove the parts in the order below.
1 Air chamber 1
2 Clamp screws 4 Loosen
3 Air temperature sensor coupler 1 (MMGOOP)
4 Throttle cable 1
5 Carburetor switch (T.O.R.S.) leads 2
6 TPS coupler 1 (VXGOOXTRISX)
7 Solenoid valve couplers 4 (MMGOOP)
8 Starter cable 1
9 Fuel delivery hoses 2
10 Carburetors 1
dure.
CARBURETORS ml
* Intake silencer
First, remove the throttle cable from the cable guide on the steering column.
Adjust the throttle cable free play while the cable is i n the cable guide.
After adjusting the throttle cable free play, properly install the upper and lower intake silencer
plates and seal.
Order Job name/Part name Q'~Y Remarks

Carburetors removal Remove the parts i n the order below.
1 Spark plug caps 3
2 Clamp screws 6 Loosen
3 Carburetor switch (T.O.R.S.) leads 2
4 Clamp 1
5 Coolant hoses 3
6 Throttle cable 1
7 Starter cable 1
8 Fuel hoses 3
9 Carburetors 1
dure.
.
Order Job name/Part name Q'~Y Remarks
Carburetor separation Separation the parts in the order below.
@ Coolant hoses 4
@ Starter cable holder 1
@ Collar 1
@ Spring 1
@ Screw 3 Loosen
@ Starter rod 1
@ Spring 1
@ Starter levers 3
@ Breather hoses 3
@ Top covers 3
@ Gaskets 3
@ Throttle shaft connecting screws 3
@ Connecting plate (upper) 1
@ Connecting plate (lower) 1
For assembly, reverse the separation proce-
dure.
ELECTRICAL
GRIP WARMER SYSTEM
CIRCUIT DIAGRAM (VT700)
GRIP WARMER SYSTEM 1-
TROUBLESHOOTING
I GRlP WARMER DOES NOT OPERATE.

I
Check the main switch.
a°K1 NO CONTINUITY
Check the grip and thumb warmer. r

Replace the main switch.
a°K1 NO CONTINUITY
Check the variable resistor. r

Replace the grip warmer and/or thumb warmer.
Replace the variable resistor.

r
Check the passenger grip warmer.
a oK l
NO CONTINUITY
Check the passenger grip warmer switch. r

Replace the passenger grip warmer.
a oK
NO CONTINUITY
Check the resistor resistance. r

Replace the passenger grip warmer switch.
Replace the resistor.

Check the grip warmer coil. r
Replace the CDI magneto.

r
Check the lighting coil.
Replace the CDI magneto.
'
Check the stator coil and/or connection. r
a OK
NO CONTINUITY
Replace the voltage regulator. r

Replacethe CDI magneto and/or correct connection.
GRlP WARMER SYSTEM
PASSENGER GRIP WARMER
(VnOO)
1. Disconnect:
Passenger grip warmer coupler
2. Connect:
Pocket tester (90890-03112, YU-03112)
(to passenger grip warmer coupler)
3.Check:
Passenger grip warmer continuity
No continuity -+ Replace.
PASSENGER GRlP WARMER SWITCH

(VnOO)
1. Disconnect:
Passenger grip warmer switch coupler
2. Connect:
Pocket tester (90890-03112, YU-03112)
(to passenger grip warmer switch coupler)
3. Check:
Passenger grip warmer switch continuity
Faulty + Replace.
0----0 Continuity
GRIP WARMER SYSTEM
RESISTOR (VT700)
1-
1. Disconnect:
Resistor coupler
2. Connect:
Pocket tester (90890-03112, YU-03112)
(to resistor coupler)
3. Measure:
Resistor resistance
For the continuity between "Black and
Black".
Out of specification + Replace.
m(1
Resistor resistance:
(Black - Black)
GENERAL SPECIFICATIONS En
SPEC
SPECIFICATIONS
GENERAL SPECIFICATIONS
VX500XTR VX6OOXTRlSX VX7OOXTIXTCI
Model XTCDIXTCPISXS
vnoo
Model code number: 8DT (VX500XTR) 8DV (VXGOOXTR) 8DS (VX700XT)
8DR(VXGOOSX) 8DH (VX700XTC)
8DK (VX700XTCD)
8DL (VX700XTCP)
8DU (VX7OOSXS)
8DM (VT700)
Dimensions:
Overall length 2,760 m m (108.7 in)
2,970 m m (116.9 in) (VT700)
Overall width 1,200 m m (47.2 in)
1,170 m m (46.1 in) (VXGOOSX, VX7OOSXS)
Overall height 1,230 m m (48.4 in) (VX500XTR, VX6OOXTR, VX700XTlXTClXTCP)
1,085 m m (42.7 in) (VXGOOSX, VX700SXS)
1,300 m m (51.2 in) (VX7OOXTCD, VT700)
Weight: 222 kg (489 Ib) (VXGOOSX, VX700XTC)
223 kg (492 Ib) (VX700XT)
225 kg (496 Ib) (VX700XTCP)
227 kg (500 Ib) (VX700SX/SXS)
231 kg (509 Ib) (VXGOOXTR)
232 kg (511 Ib) (VX500XTR)
234 kg (516 Ib) (VX700XTCD)
264 kg (582 Ib) (VT700)
Minimum turning radius:
Clockwise 4.0 m (13.1 ft)
3.8 m (12.5 ft) (VXGOOSX, VX7OOSXS)
Counterclockwise 4.0 m (13.1 ft)
3.8 m (12.5 ft) (VXGOOSX, VX700SXS)
Engine:
Engine type Liquid cooled 2-stroke, piston port
Induction system Piston reed valve Crankcase reed valve
Cylinder arrangement Forward inclined parallel 2-cylinder Forward inclined
parallel 3-cylinder
Displacement 494 cm3(30.1 cu.in) 598 cm3(36.5 cu.in) 698 cm3(42.6 cu.in)
Bore x Stroke 68 x 68 mm (2.68 x 2.68 in) 74.8x 68 mm (2.94 x 2.68 in) 70.5x59.6mm (2.78x2.35in)
Compression ratio 6.5 : 1 6.0 : 1 6.7 : 1
Maximum horse power 64 kW/7,750 rlmin 69.1 kW/7,750 rlmin 80.9 kW/8,500 rlmin
85.8 BHP/7,750 rlmin 92.6 BHP/7,750 rlmin 108.4BHP/8,500r/min
Maximum torque 78.4 Nm/7,750 rlmin 85.3 Nm/7,750 rlmin 93 Nm/8,250 rlmin
57.82 ft-lb/7,750 rlmin 62.91 ft-lb/7,750 rlmin 68.59 ft-lb/8,250 rlmin
Starting system (Manual model) Recoil hand starter
(Electric model) Electric and recoil hand starter
Lubrication system: Separate lubrication (YAMAHA AUTOLUBE)
GENERAL SPECIFICATIONS Fl
VX500XTR VXSOOXTRISX VX700XT/XTC/
Model XTCDIXTCPISXS
VT700
Engine oil:
TYpe YAMALUBE 2-cycle oil
Tank capacity 2.4 L (2.1 Imp gt, 2.5 US gt)
Drive chain housing oil:
TY~e Gear oil API "GL-3" SAE #75 or #80
Capacity 0.25 L (8.8 Imp oz, 8.45 US oz)
Coolant:
Total amount 3.3 L (2.90 Imp gt, 3.49 US gt) (VX500XTR, VXGOOXTRISX)
4.2 L (3.70 Imp gt, 4.44 US gt) (700)
4.5 L (3.96 Imp gt, 4.76 US gt) (Vr700)
Reservoir tank capacity 0.17 L (0.15 Imp gt, 0.18 US gt)
Fuel:
R+M
TY~e Regular gasoline (Pump Octane -$8)
Tank capacity 45 L (9.9 Imp gal, 11.9 US gal) 2
Carburetor:
TypeIQuantity TM36 x 2 I TM33 x 3
Manufacturer MlKUNl
Spark plug:
TY~e BR9ES BR9ECS BR9ES
Manufacturer NGK t t
Gap -
0.7 0.8 m m t t
-
(0.028 0.031 in)
Transmission:
Primary reduction system V-Belt
Primary reduction ratio 3.8- 1.1 : 1
Clutch type Automatic centrifugal engagement
Secondary reduction system Chain
Secondary reduction ratio 1.77 (39122) 1.70 (39123)(VXGOOXTR)1.739 (40123)
(VX700XT/XTC/SXS)
- 1.77 (39/22)(VX60OSX) 1.818 (40122)(VX7OOXTCP)
- - 1.773(39122)(V>CIOOXTCD,
moo)
Reverse system Yes (For VX500XTR, VXGOOXTR, VX700XTCD, W O O )
Chassis:
Frame type Monocoque
Caster 22.5"
Ski stance (center to center) 1,070 m m (42.1 in)
1,040 m m (40.9 in) (VXGOOSX, VX700SXS)
Suspension:
Front suspension type Leading arm
Rear suspension type Slide rail suspension
_I
t
GENERAL SPECIFICATIONS F l
VX500XTR VX6OOXTR/SX VX700XT/XTC/
Model XTCD/XTCP/SXS
vnoo
Track:
Track type Internal drive type
Track width 381 m m (15.0 in)
Length on ground 752 m m (29.6 in) (Except for VT700)
944 m m (37.2 in) (VT700)
Track deflection mm/lO kg (22 Ib) - -
25 30 m m (0.98 1.18 in)
Brake:
Brake type Caliper type disc brake
Operation method Handle lever, left hand operated
Electrical:
Ignition system / Manufacturer CDI / MITSUBISHI
Generator system Flywheel magneto
Bulb wattage x Quantity:
Headlight 12V,60 W/55 W x 1
TailIBrake light 12V,8W/23Wx1
Tachometer light 12V, 1 . 7 W x 1
Speedometer light 12V, 1.7 W x 1
Indicator light 12 V, 3.4 W
MAINTENANCE SPECIFICATIONS F I
MAINTENANCE SPECIFICATIONS
ENGINE
Volume (with spark plug)
Measuring point @
Piston to-cylinder clearance
Piston off-set
Piston pin length

(2.193 - 2.205 in) 1 (2.350 - 2.362 in) 1 (2.193 - 2.205 in)
Piston ring:
Sectional sketch Keystone
Top Ring B = 1.2 m m (0.047 in)
T = 2.65 mm (0.104 in11 T = 3.05 mm (0.120 in11 T = 2.55 mm (0.100 in)
Keystone
2nd Ring B = 1.2 m m (0.047 in)
T = 2.65 mm (0.104 in11 T = 3.05 mm (0.120 in) T = 2.55 mm (0.100 in)
End gap (installed) Top Ring - -
0.45 0.60 m m (0.0178 0.024 in) - -
0.35 0.55 mm (0.0137 0.0217 in1
Side clearance
2nd Ring
Top Ring
-
-
--
0.45 0.60 mm (0.0178 0.024 in)
0.02 0.06 m m (0.0008 0.0024 in)
-
t
-
0.35 0.55 mm (0.0137 0.0217 in)
2nd Ring - -
0.02 0.06 m m (0.0008 0.0024 in) t
Coating Top Ring Chrome platedlferox coating t
2nd Ring Chrome platedlferox coating t
VX500XTR VX6OOXTRlSX VX700XT/XTC/

Model XTCD/XTCP/SXS
VT700
Crankshaft:
Crank width "A" 61.95
(2.439
- 62.00 m m
- 2.440 in)
--
55.95 56.00 m m
(2.203 2.205 in)
Crank width "B" 179.85 - 180.15 m m 291.75 - 292.30 m m
(7.080 - 7.093 in) (11.486 - 11.508 in)
Crankshaft deflection "C" : Ci Below 0.03 m m (0.0012 in)
5001600 : C2, C3 Below 0.04 m m (0.0016 in)
500/600: C4 Below 0.05 m m (0.0020 in)
-
700: C2 C5 Below 0.04 m m (0.0016 in)
700: C6 Below 0.03 m m (0.0012 in)
Measuring points: 1 80 m m (3.15 in) 90 m m (3.54 in)
2 99 m m (3.90 in) 85 m m (3.35 in)
Connecting rod big end side clear- 0.25 - 0.75 m m (0.01 - 0.03 in)
ance "DM
Connecting rod small end free play "F" 1 0.8 - 1.0 m m (0.03 - 0.04 in)
5001600 700
F D F
Big end bearing:

TYpe Needle bearing
Small end bearing:
TYpe Needle bearing
Crank pin:
Crank pin outside diameter -
24.987 25 m m -
26.993 27.000 m m
-
(0.98 0.98 in) -
(1.06 1.06 in)
Connecting rod:
Small end diameter 24.995 - 25.008 m m (0.98 - 0.98 in)
Big end diameter -
32.005 32.018 m m
- -
34.020 34.033 mm
2
(1.26 1.26 in) -
(1.34 1.34 in)
MAINTENANCE SPECIFICATIONS Fl
VX500XTR VXGOOXTR/SX VX700XT/XTC/
Model XTCD/XTCP/SXS
moo
Carburetor:
Type / Quantity TM36 / 2pcs. t TM33 / 3pcs.
Manufacturer MlKUNl t t
I.D. mark 8CJOO 8CR00 8CH-10
Main jet (M.J) # I 51.3 t #1 : #I45
#2,3 : #143.8
Main air jet (M.A.J) 02.5 t -
Pilot jet (P.J) #45 t t
Jet needle (J.N) 8CFY 14-56-2 8DFY8-57-2 6DGM05-3
Needle jet (N.J) Q-6 t # I : 0-8
#2,3 : 0-4
Pilot air jet (P.A.J) 0.8 t 1.0
Pilot outlet (P.0) 00.9 00.8 t
Bypass (B.P.1) 1.O t 0.8
Pilot screw (P.S) 1-314 1-112 t
Throttle valve (Th.V) 3.0 t 3.5
Valve seat size (V.S) 01.5 t 01.2
Starter jet ((3.S) 00.9 t 01.1
Float height (F.H) -
21.3 23.3 m m t -
11.3 15.3 m m
-
(0.84 0.92 in) -
(0.44 0.60 in)
Fuel level (from the bore center) -
40 42 m m t -
36 38 m m
-
(1.57 1.65 in) -
(1.42 1.50 in)
Engine idle speed 1,60W100 rimin 1,550k100 r/min 1,600k100 r/min
Fuel pump:
Type DIAPHRAM
Manufacturer TAIYO GlKEN
Oil pump:
Pump cable adjusting length Align the marks t -
21 23 m m
-
(0.83 0.91 in)
Cooling system:
Water pump drive belt tension - -
8 mm/lO 14 kg (0.3 in122.0 30.9 Ib) -
- -
8 mml13 20 kg (0.31in128.7 44.1 Ib)(NEW BELT)
Filler cap opening pressure -
80 100 kPa 100- 120kPa
-
(0.8 1.0 kg/cm2, 11 - 14 psi) - -
(1.0 1.2 kglcm2,14 17 psi)
Water pump type Impeller type
Coolant type High quality ethylene glycol anti-freeze containing corrosion
inhibitor
Coolant mixing ratio (coolant: water) 3:2 (60%/40%)
Coolant capacity 3.3 L (2.90 Imp qt, 3.49 US qt) (VX500XTR, VX6OOXTR/SX)
4.2 L (3.70 Imp qt, 4.44 US qt) (700)
4.5 L (3.96 Imp gt, 4.76 US gt) (Vr700)
Reservoir tank capacity 0.17 L (0.15 Imp qt, 0.18 US qt)
MAINTENANCE SPECIFICATIONS F l
VX500XTR VXGOOXTRISX VX7OOXT/XTC/
Model XTCDIXTCPISXS
VT700
Thermostat:
Opening temperature - -
50 55°C (122°F 132°F)
Valve lift 8 mm / 70°C (159°F)
High altitude settings
MAINTENANCE SPEClFlCATlONS F l
VX500XTR
\Altitude
Tempera-
0-100m
-
(0 330 ft)
-
100 500 m MJ #152.5
M J #151.3
MJ #150 MJ # I 48.8
-
(330 1,600 ft) JN-2.0
JN-2.0
(Production)
JN-2.0 JN-2.0
1,000- 1,500 m
(3,300- 4,900 ft)
1,500 - 2,000 m
(4,900 - 6,600 ft)
M J #I40 M J #138.8
2,000
(6,600
-- 2,500 m
8,200 ft)
JN-1.0
PJ #50
JN-1.0
PJ #50
PS 2-112 PS 2-112
M J #138.8 MJ #136.3
2,500
(8,200
-- 3,000 m
9,800 ft)
JN-0.5
PAJ 0.6, PJ #50
JN-0.5
PAJ 0.6, PJ#50
1 PS 2-112 1 PS 2-112
:Production spec] AJ: #151.3 PJ: .5 JN: 8CFY14-56-2 PAJ: 0.8 PS: 1-314
tf: Main jet nu.mber JN: Jet needle clip position PS: Pilot screw turns out PJ: Pilot jet number
NOTE:
Jet needle (JN) position.
Refer to the following information for the Jet needle shims installation.
JN:2 (STD) JN:1.5 JN:1 JN:0.5
- f--w
..................,... -
-- - b
Clip
0.4 rnm shim
Oxygenated fuels
Use one size larger Main Jet than specified.
MAINTENANCE SPECIFICATIONS F i
VX6OOXTRlSX
I o-loom
(0 - 330 ft) II
MJ#156.3
JN-2.0
MJ#155
JN-2.0
I -
-
100 500 m
(330 1,600 ft)
M J #I55
JN-2.0
MJ #153.8
JN-2.0
MJ #152.5
JN-2.0
M J #151.3
/JN2'o
(Production) IJN-2.0
MJ #150
1
I 1,000
(3,300
- 1,500 m
- 4,900 ft)
M J # I 50
JN-1.5
M J # I 48.8
JN-1.5
I 1,500
(4,900
2,000
- 2,000 m
- 6,600 ft)
-- 2,500 m
M J #147.5
JN-1.5
M J # I 45
M J #146.3
JN-1.5
MJ # I 43.8
(6,600 8,200 ft) JN-1.5 JN-1.5
MJ #I40 MJ #138.8
2,500 - 3,000 m MJ # I 43.8 MJ # I 42.5 JN-0.5
(8,200 - 9,800 ft) JN-1.0 JN-1.0 JN-1.0
[Production spec] MJ: #151.3 PJ: #45 JN: 8DFY8. i7-2 PAJ: 0.8 PS: 1-112
#: Main jet number JN: Jet needle clip position PS: Pilot screw turns out PJ: Pilot jet number
NOTE:
Refer to the following information for the Jet needle shims installation.
JN:2 (STD) JN:1.5 JN:1 JN:0.5
- -- --
-
......................
..............
Oxygenated fuels
-R -- --W
............
-- r......:.:.:.1:.:.:.:(
Clip
0.4 m m shim
VX7OOXT/XTC/XTCD/XTCP/SX/SXS
\
Altitude
Tempera-
100- 500m
-
(330 1,600 ft)
M J # I #143.8 MJ#1 #142.5 MJ#1 #141.3

-
500 1,000 m
MJ #2#3 #142.5 MJ #2#3 #141.3 MJ #2#3 #140.0
-
(1,600 3,300 ft)
PJ
JN
#50.0 PJ
2.5 JN
#50.0 PJ
2.5 JN
#50.0
2.5
PS 1-112 PS 1-112 PS 1-112
MJ#1 #142.5 MJ#1 #141.3 MJ#1 #140.0 MJ#1 #138.8
MJ#2#3 #141.3 MJ #2#3 # I 40.0 MJ #2#3 #138.8 MJ #2#3 #137.5
PJ #52.5 PJ #52.5 PJ #52.5 PJ #52.5
JN 2.5 JN 2.5 JN 2.0 JN 2.0
PS 1-314 PS 1-518 PS 1-518 PS 1-518
MJ#1 #140.0 MJ#1 #138.8 MJ#1 #137.5 MJ#1 #136.3
1,500 - 2,000 m MJ #2#3 #138.8 MJ #2#3 #137.5 MJ #2#3 #136.3 MJ #2#3 #135.0
(4,900 - 6,600 ft) PJ
JN
#55.0 PJ
2.0 JN
#55.0 PJ
2.0 JN
#55.0 PJ
2.0 JN
#55.0
2.0
PS 2.0 PS 1-718 PS 1-718 PS 1-718
MJ#1 #137.5 MJ#1 #136.3 MJ#1 #135.0 MJ#1 #133.8 MJ#1 #132.5
2,000 - 2,500 m M J #2#3 #136.3 MJ #2#3 #135.0 MJ #2#3 #133.8 MJ #2#3 #132.5 MJ#2#3 #131.3
(6,600 - 8,200 ft) PJ #57.5 PJ
JN
#57.5 PJ
2.0 JN
#57.5 PJ
2.0 JN
#57.5 PJ
2.0 JN
#57.5
2.0
2-118 PS 2.0 PS 2.0 PS 2.0 PS 1-718
MJ#1 #133.8 MJ#1 #132.5 MJ#1 #131.3 MJ#1 #130.0
2,500 - 5,000 m M J #2#3 #133.8 MJ #2#3 #132.5 MJ#2#3 #131.3 MJ#2#3 #130.0 MJ #2#3 #128.8
(8,200 - 9,800 ft) JN
#60.0 PJ
2.0 JN
#60.0 PJ
2.0 JN
#60.0 PJ
2.0 JN
#60.0 PJ
2.0 JN
#60.0
1.5
PS 2-114 PS 2-118 PS 2-118 PS 2-118 PS 2.0
Production spec] #1:#145 MJ# !,3: #143.8 PJ: #45 JN: 6DGM05-3 PAJ: 1 3 PS: 1-112
#: M a i n jet number 4: Jet needle cl p position PS: Pilot screw turns out PJ: Pill it jet number
NOTE:
Refer t o the following information for the Jet needle shims installation.
JN:2 (STD) JN:1.5 JN:1 JN:0.5
- -- ............
--
--
- 3-1
Clip
0.4 m m shim
Oxygenated fuels
Use one size larger M a i n Jet than specified.
VT700
Altitude
PS 1-314 PS 1-518
MJ#1 #140.0 MJ#1 #138.8
1,500 - 2,000 m MJ #2#3 #138.8 MJ #2#3 #137.5
(4,900 - 6,600 ft) pJ
jN
#57.5
2.0
PJ
JN
#57.5
2.0
PS 2.0 PS 1-718
MJ#1 #137.5 MJ#1 #136.3
MJ#1 #132.5 MJ#1 #131.3 MJ#1 #130.0
~!i
MJ#2#3 #131.3 MJ#2#3 #130.0 MJ#2#3 #128.8
#62.5 PJ #60.0 PJ #60.0
2.0 IJN 1.5 IJN 1.5
I IPS2-114 IPS 2-118 2-118 PS 2-118 PS 2.0
Production spec] MJ#1: # I 45 MJ#2,3: # I 43.8 P. :#45 JN:6DGM05-3 PAJ: 1.0 PS: 1-112
Y: Main jet number JN: Jet needle clip position PS Pilot screw turns out PJ: Pilot jet number
NOTE:
Refer t o the following information for the Jet needle shims installation.
JN:2 (STD) JN:1.5 JN:1 JN:0.5
- -- .......,....................,.,... --
-
fm ......
.....,,.,.,.,.,.,.
,. .,..
1 Clip
0.4 m m shim
Oxygenated fuels
Tightening torque:
Parts to be tightened
1 Tightening torque
Remarks
Crankcase (first) Tighten the bolts in two

(final) stages.
Engine bracket (front) and frame 5001600
700
Engine bracket damper (front)
Engine bracket and engine
Engine bracket upper and lower (rear) 5001600
700
Engine bracket damper and frame (rear)
Water pump housing (Except for 700)
Cylinder head
Nut 5001600 (first) Tighten the nuts in two
(final) stages.
700 (first)
(final)
Cylinder body
Nut 5001600
700
Spark plug
Thermostatic valve cover
Water pump drive pulley (Except for 700)
Impeller 5001600 Left-Hand threads
700
Oil pump
Recoil starter 5001600
700
Carburetor
Pilot jet
Valve seat
Main jet
Coolant drain bolt 5001600
700
Magneto rotor nut
Starter motor bolt
POWER TRAIN
MAINTENANCE SPECIFICATIONS 1-
Engagement r/min
Sheave center distance "A"

Sheave offset "B"
-
18.5 21.5 m m (0.73 0.84 in) -
(VX500XTR, VX6OOXTR, VX7OOXTCD, VT700)
Outside circumference
34.5 m m (1.36 in)
Wear limit "B"
90501-550J8 90501-555J9
90501-602JO ( K ' O O )
90501-58553 (VX70OXTCP)
- - Pink (VT7OO)
- - Green-Pink-Green(VX7GUXTCP)
Diameter 48 m m (1.89 in) t t
Wire diameter 5.5 m m (0.21 in) c t
- - 5.8 mm (0.22 in)(VX7GUXTCP)
- - 6 mm (0.23 in) (VnOO)
Preload 294.2 N (29.4 kg, 66.09 Ib) 342 N (34.3 kg, 77.1 1Ib) t
- - 294.2 N(29.4 kg, 66.09 Ib)(W7W
Spring rate 22.1 Nlmm (2.21 kglmm, 124 Iblin) c t
- - 29.1Nlmm (2.94 Irglmm, 161Iblinl WOO1
Number of coils 4.62 4.66 4.96
- - 4.74 (VT700)
Free length 78.7 m m (3.09 in) 81.0 m m (3.18 in) c
- - 76.3 mm (3.00 in) (VX700XTCP)
- - 75.4 mm (2.96 in) (WOO)
MAINTENANCE SPECIFICATIONS 1-1
Model XTCDIXTCPISXS
VT700
Primary sheave weight arm:
Part number (with bushing) 8AB-17605-01 8CR- 17605-00 8CH-17605-00
Weight 41 g (1.45 oz) 38.1 g (1-34 oz) 35.3 g (1.25 oz)
Rivet:
Outer
Model VX500XTR VX6OOXTR Except for VT700
Part number 90261-06019 90261-06015 90261-06034
Material Steel t t
Size 13.3 m m (0.52 in) 10.3 m m (0.41 in) 13.9 m m (0.55 in)
Model - VX6OOSX W O O
Part number - 90261-06034 t
Material - Steel t
Size - 13.9 m m (0.55 in) t
Quantity 3pcs t t
Hole quantity 3pcs t t
Inner
Model - VX6OOXTR Except for VT700
Part number - 90261-06033 90261-06034
Material - Steel t
Size - 17.2 m m (0.68 in) 13.9 m m (0.55 in)
Model - VX6OOSX VT700
Part number - 90261-06034 90261-06033
Material - Steel t
Size - 13.9 m m (0.55 in) 17.2 m m (0.68 in)
Quantity - 3pcs t
Hole quantity - 3pcs t
VX500XTR VX6OOXTRlSX
En SPEC
VX7OOXTIXTCI
Model XTCD/XTCP/SXS
VT700
Secondary sheave spring:
Part number 90508-536A9 t (VX6OOXTR) -
- 90580-556A2 t
(VX6OOSX)
Color code Red c -
- Green (VX6OOSX) t
Outside diameter 69.5 m m (2.74 in) t c
Wire diameter 5.3 m m (0.21 in) c 5.5 m m (0.22 in)
Hole position
&
Sheave side-spring side (twist angle) 2-6 (80") 3-3 (60") (VX6OOXTR) t
- 1-3(40") (VX6OOSX) 1-6 (70") (Vr700)
O / ,
Spring rate 7.3 N/mm (0.73 kg/mm, t (VX6OOXTR) -

41.68 Ib/in)
- 8.5 N/mm (0.85 kglmm, t
48.54 Ibhn) (VX600SX)
Number of coils 5.53 c t
Free length 75 m m (2.95 in) c t
Torque cam angle 45" 47" (VX6OOXTR) 45"
- 43" (VX60OSX) -
Drive chain:
Type S37TNB13 c c
Number of links 70L t t
Track:
Part number 8AB-47 110-10 8CA-47110-10 8CH-47110-10
- - 8DL-47110-OO(VX700XrcP)
- - 8BN-47110-10(Vr700)
Width 381 m m (15.0 in) c t
Length 3,072 m m (120.9 in) t t
- - 3,456mm(136.1 in)
(VT700)
Pitch 64 m m (2.52 in) t t
Number of links 48 t t
- - 54 (Vr700)
Height "B" 16 m m (0.63 in) t t
m0
7-
Deflection at 10 kg (22 Ib) 25-30mm(0.98-1.18in) c t
VX500XTR VXGOOXTR/SX VX700XT/XTC/
Model XTCD/XTCP/SXS
VT700
Slide rail suspension:
Front travel 230 m m (9 in) t (VXGOOXTR) t (VX700XT/XTC/
XTCD/XTCP, W O O )
- 177 mm (7 in) (VXGOOSX) t (VX7OOSXS)
Rear travel 290 m m (11.5 in) t (VXGOOXTR) t (VX700XT/XTC/
XTCDKTCP, Vr700)
- 225 mm (8 in) (VX6OOSX) t (VX7OOSXS)
Suspension spring rate
Front 11.76 Nlmm (1.176 kg1 t (VXGOOXTR) t (VX7OOXT/XTC/
mm, 67.15 Iblin) XTCD/XTCP,VT700)
- 45 N/mm (4.5 kg/mm, -
256 Ib/in)
(VXGOOSX)
- - 48 N/mm (4.8 kg/
mm, 274 Ib/in)
(vX700SXS)
Rear -
27 45 N/mm t (VXGOOXTR) -
30 45 N/mm
-
(2.7 4.5 kg/mm, -
(3 4.5 kg/mm,
-
154 256 Iblin) -
171 257 Iblin)
(VX700XT)
- -
25 45 Nlmm -
30 50 N/mm
-
(2.5 4.5 kg/mm, -
(3 5 kglmm,
137-257Iblin) 171-285IbJin)
(VXGOOSX) (VX700XTC/XTCD/
XTCP/SXS)
- - -
35 53 Nlmm
-
(3.5 5.3 kg/mm,
-
200 303 Ib/in)
(VT700)
VX500XTR VXGOOXTRISX VX70OXT/XTC/
Model XTCDIXTCPISXS
VT700
Spring wire diameter
Front 6.5 m m (0.25 m m ) t (VXGOOXTR) t (VX'IOOXT, VT700)
- 9 m m (0.35 in) t (VX700SXS)
(VXGOOSX)
- - 6.8 m m (0.27 in)
(VX700XTC/XTCD/XTCP)
Rear 11.2 m m (0.44 in) t (VXGOOXTR) 12 mm (0.47 in) (WOO)
- 10.5 mm (0.41in) (VXGOOSX) 11.5mm(0.45in)(VX700XT)
- - 11.8 m m (0.46 in)
(VX700XTC/XTCD/XTCP)
- - 10.5 m m (0.41 in)
(vX70oSXS)
Suspension setting position:
Stopper band hole position (F) NO.l t
*
t
Hook setting length 10 m m (0.39 in) t (VXGOOXTR) t (VX7OOXT)
-
&a
25 mm (0.98 in) (VXGOOSX) t (VX700XTCl
XTCDIXTCPISXS,
VT700)
Full rate adjusting position ** B t t
A
VX500XTR VXGOOXTR/SX VX7OOXTIXTCI
Model XTCD/XTCP/SXS
moo
Shock absorber: Damping force
Front
Extension 451 f 88 N/0.3 m/s (VX500XTR, VXGOOXTR, VX700XT)
3,412 f 460 Nl0.3 m/s (VX6OOSX)
2,050 f 280 Nl0.3 m/s (VX7OOXTCIXTCDIXTCP)
3,412 f 460 Nl0.3 m/s (VX7OOSXS)
510 f 98 N/0.3 m/s (VT700)
Compression 1,304 f 265 Nl0.3 mls (VX500XTR, VXGOOXTR, VX~OOXT)
1,265 f 225 Nl0.3 mls (VX6OOSX)
1,480 f 260 Nl0.3 m/s (VX7OOXTC/XTCD/XTCP)
+
1,912 264 N10.3 m/s (VX700SXS)
1,775 f 353 Nl0.3 rnls (VT700)
Rear
Extension +
2,206 657 Nl0.3 mls (VX500XTR, VXGOOXTR, VX~OOXT)
1,657 f 235 N/0.3 m/s (VXGOOSX)
2,750 f 370 N/0.3 m/s (VX7OOXTClXTCDlXTCP)
1,912 f 264 Nl0.3 m/s (VX7OOSXS, W O O )
Compression 726 f 216 N10.3 m/s (VX500XTR, VXGOOXTR, VX700XT)
1,235 f 215 Nl0.3 m/s (VXGOOSX)
+
860 I 6 0 Nl0.3 m/s (VX700XTC/XTCD/XTCP)
+
1,353 235 Nl0.3 mls (VX7OOSX/SXS, W O O )
Slide runner:
Thickness 17.8 m m (0.70 in)
Wear limit 10 m m (0.39 in)
Track sprocket wheel:
Material Polyethylene
Number of teeth 9T
Rear guide wheel:
Material High-molecular-weight polyethylene with rubber
Outside diameter 178 m m (7.01 in)
Brake:
Pad thickness 10.2 m m (0.40 in)
Pad wear limit 1.0 m m (0.04 in)
Disc outside diameter 220 m m (8.66 in)
Disc thickness 10 m m (0.39 in)
i
MAINTENANCE SPEClFlCATlONS ISPECICSI.1
Tightening torque:
Parts to be tightened
Primary sheave
I-=-
Tig h ening torque
12.0
Remarks
Spider and stiding sheave Left-hand thread.

Apply LOCTITEQ3
I Primary sheave cap and sliding sheave
' Roller and weight (primary sheave)
Bolt
Screw
Ring gear Apply LOCTITE@
Secondary sheave
Drive sprocket
Lock nut chain tensioner
Chain housing and frame
' Driven sprocket Apply LOCTITEQ3
Drain bolt
Chain housing cover
Chain housing and brake caliper
I Bearing holder (jackshaft) Apply LOCTITEB
Suspension wheel
Guide wheel
I Sliding frame and slide runner
I :
Slide rail suspension mounting bolt
Slide rail suspension mounting bolt (rear) (For VT700)
Rear pivot arm and bracket Apply LOCTITEm
Shock absorber and rear pivot arm
Rear pivot arm and rod
Rear suspension bracket and rod
Control rod and sliding frame
Front pivot arm and sliding frame
Shock absorber and front pivot arm
Shock absorber and bracket
Shock absorber and rear pivot arm
Bracket shaft and sliding frame
Collar (front axle)
Speedometer gear
Tightening torque
Parts to be tightened Remarks
Nm m-kg ft-lb
Handlebar holder 15 1.5 11
Steering column
Upper 23 2.3 17
Lower 23 2.3 17
Steering column and relay rod 35 3.5 25
Relay rod and relay arm 35 3.5 25
Relay arm and tie rod 35 3.5 25
Tie rod and steering arm 54 5.4 38
Locknut (relay rod) 25 2.5 18 Apply LOCTITE@
Ski runner 26 2.6 19
Ski 48 4.8 35
Ski runner 21 2.1 15 (VX700XTCP)
Ski column lower bracket 10 1.0 7.2 (VX700XTCP)
Shock absorber (upper) 48 4.8 35
Shock absorber bracket 40 4.0 29 (VX6OOSX)
Shock absorber (lower) 48 4.8 35
Steering arm and ski column 48 4.8 35
Lower control arm and frame 50 5.0 36
Upper control arm and frame 50 5.0 36
Control arm and front arm 48 4.8 35
Front arm pivot bolt 78 7.8 56
Stabilizer bar and connecting rod 23 2.3 17
Connecting rod and front arm 56 5.6 40
Hood 3 0.3 2.2
Seat and frame (nut) 9 0.9 6.5
Front cowling 3 0.3 2.2
.CHASSIS
Model XTCDIXTCPISXS
VT700
Frame:
Frame material Aluminum
Seat height 730 m m (28.7 in)
Luggage box location Rear side of seat
Steering:
Lock-to-lock angle (left) 29.4" (R ski) 34.7" (L ski)
(right) 34.7" (R ski) 29.4" (L ski)
(left) 29.6" (R ski) 34.8" (L ski) (VXGOOSX, VX700SXS)
(right) 34.8" (R ski) 29.6" (L ski) (VXGOOSX, VX700SXS)
Ski alignment Toe-out
Toe-out size - -
0 15 m m (0 0.59 in)
Caster angle 22.5"
Ski:
Ski material Steel
Plastic (VX700XTCP)
Length 1,032 m m (40.6 in)
Width 128 m m (5.04 in)
140 m m (5.51 in) (VX700XTCP)
Thickness 2 m m (0.08in)
Ski ground length 178 m m (7.01 in)
221 m m (8.7 in) (VT700)
Ski suspension:
Type Proaction system
Travel 222 m m (8.74 in)
178 m m (7 in) (VX500XTR, VXGOOXTR, VXGOOSX, VX700SXS, VT700)
222 m m (8.7 in) (VX700XT/XTC/XTCD/XTCP)
Spring type Coil spring
Spring rate 19 Nlmm (1.9 kglmm) (VX500XTR, VXGOOXTR)
2 1 N/m m (2.1 kglm m) (VX700XT/XTC/XTCD/XTCP)
23 Nlmm (2.3 kglmm) (VXGOOSX, VX700SXS, VT700)
Wire diameter 8 m m (0.31 in)
8.43 m m (0.33 in) (VXGOOSX)
8.2 m m (0.32 in) (VX700XTCP)
Shock absorber: damping force
Extension 1,750 Nl0.3 mls (VX500XTR, VXGOOXTR)
1,360 Nl0.3 mls (VXGOOSX)
1,270 Nl0.3 mls (VX700XT)
1,700 N10.3 mls (VX700XTClXTCDlXTCP)
940 Nl0.3 m/s (VT700)
1,415 N10.3 mls (VX700SXS)
Compression 346 Nl0.3 mls (VX500XTR, VXGOOXTR)
650 Nl0.3 m/s (VXGOOSX)
790 N10.3 mls (VX700XT)
370 NI0.3 mls (VX7OOXTClXTCDlXTCP)
845 Nl0.3 mls (VX700SXS)
700 Nl0.3 mls (VT700)
ELECTRICAL
VX500XTR VX6OOXTR/SX VX7OOXT/XTC/
Model XTCD/XTCP/SXS
VT700
Voltage: 12 V
lgnition system:
Ignition timing (B.T.D.C.) 16" at 1,600 rimin 12" at 1,500 rlmin 18" at 1,500 rlmin
Advanced timing (B.T.D.C.) 18" at 4,500 rlmin 24" at 4,500 r/min
Advanced type Electrical type
lgnition coil:
Model / Manufacturer 8AB-00 / YAMAHA 8CH-00 / YAMAHA
Minimum spark gap 3 m m (0.1 18 in) or more t
-
Primary coil resistance
Secondary coil resistance --
0.16 0.24 SZ at 20°C (68°F)
3.9 5.9 WZ at 20°C (68°F)
0.18 0.24 R at 20°C ((68°F)
-
2.7 3.7 kQ at 20°C (68°F)
Spark plug cap:
Type Rubber type
Model / Manufacturer 81E / TOKAI DENS0
Resistance 5 WZ at 20°C (68°F)
Charging system:
Type Flywheel magneto
CDI:
Magneto model/Manufacturer F4T318 / MlTSUBlSHl F4T326/MlTSUBISHI
Pickup coil resistance -
189 231 SZ at 20°C (68°F) t
(color code) (WhiteJRed-WhiteIGreen) t
Source coil resistance -
279 341 R at 20°C (68°F) -
392 479 Rat 20°C ((68°F)
(color code) (Brown-BlackIRed) t
Charging current-(Minimum) 0.5 A at 3,000 rlmin t
Charging current-(Maximum) 2.5 A at 8,000 rlmin t
Charging coil resistance -
0.29 0.35 SZ at 20°C (68°F) -
0.28 0.34 R at 20°C (68OF)
(color code) (White-Black) t
Lighting voltage-(Minimum) 11 V at 3,000 r/min t
Lighting voltage-(Maximum) 15 V at 8,000 rlmin t
Lighting coil resistance -
0.27 0.33 R at 20°C (68°C) -
0.25 0.31 R at 20°C ( 6 8 O F I
(color code) (Yellow-Black) t
Grip warmer coil resistance -
1.O 1.2 LI at 20°C (68°F) -
1.5 1.9 R at 20°C (68°F)
(color code) (Yellow/Black-Black) t
8CJ-01 (MITSUBISHI) I 8CR-10 (MITSUBISHII 8CH-00 (MITSUBISHI)
I
CDI unit manufacturer
VX500XTR VX6OOXTR/SX VX7OOXTIXTCI
Model XTCD/XTCP/SXS
VT700
Rectifier/regulator:
Model / manufacturer 89A-00 / MATSUSHITA
No load regulated voltage AC -
13.8 14.8 V
DC 14.0-15.OV
Battery: (for electric model)
Specific gravity 1,280 1,280
TYP~ Y B1GAL-A2 G M182-3A
Electric starter system: (for electric model)
Type Bendix type
Starter motor: (for electric model)
Model / manufacturer DB4XF / DENS0
Output 0.6 kW
Armature coil resistance -
0.014 0.018 Q at 20°C (68.F)
Brush: Overall length 12 rnrn (0.48 in)
Wear limit 8.5 mrn (0.33 in)
Spring pressure - - -
6.5 9.5 N (650 950 g, 22.9 33.5 oz)
Commutator diameter 28 mrn (1.10 in)
Wear limit 27 m m (1.06 in)
Mica undercut - -
0.4 0.8 m m (0.016 0.031 in)
CABLE ROUTING 1SPEC1 1
CABLE ROUTING <500/600>
@ Grip warmer lead

L
/ @ DCback buzzer
@ Voltage regulator
To @
\
@ Intake silencer I silencer.
First, remove the throttle cable from the cable guide on the
steering column.
Adjust the throttle cable free play while the cable is in the cable
guide.
After adjusting the throttle cable free play, properly install the
upper and lower intake silencer plates and seal.
CABLE ROUTING FI
05 Oil level gauge coupler
@ Route the fuel hose through

the hose slot o n the intake
silencer. @ Water temperature sensor coupler
\ @ Carburetor switch lead
@ ECU (MMGOOP)
@ CDI magneto coupler
@ Air vent hose (MMGOOP)

CABLE ROUTING c700>
Q) Grip warmer lead
@ Wire harness
@ Clamp/
CABLE ROUTING SPEC^ (
@ Brake hose @ Parking brake cable

I
-----'I
@ Speedometer cable /
@ Intake silencer
@ Carburetor heating lever
' \\\
\ \\
First, remove the throttle cable from the cable guide

the hose slot on the intake
silencer.
on the steering column. \

Adjust the throttle cable free play while the cable is
in the cable guide.
After adjusting the throttle cable free play, properly
install the upper and lower intake silencer plates
and seal. \
@ Oil level gauge coupler

the hose slot on the intake
silencer.
@ Wire harness
@ Starter cable
7 7
YAMAHA
PRINTED ON RECYCLED PAPER

Yamaha: Supplementary Service Manual

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

Yamaha: Supplementary Service Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Yamaha: Supplementary Service Manual

Uploaded by

Copyright:

Available Formats

YAMAHA

SUPPLEMENTARY SERVICE MANUAL

lllustrated symbols@to@aredesigned asthumb

lllustrated symbols @ t o @ are used t o identify

Illustrated symbols @ t o @ i n the exploded dia-

1 1 1 Q) Apply gear oil

GENERAL INFORMATION .................................. 1 ENGINE ............................................................. 52

ENGINE SERIAL NUMBER

When checking T.O.R.S.:

1. Start the engine.

2. Hold the pivot point of the throttle lever away

If the engine does not run between 2,800 and

When installing the n e w V-belt, make sure that it

As the V-belt wears, adjustment may be neces-

New belt width:

Standard V-belt height I

V-belt height adjustment

To move V-belt up: Add spacer

To move V-belt down: Reduce spacer

To move V-belt up: Reduce spacer

To move V-belt down: Add spacer

The engine and muffler will be very hot after the

1. Place the machine on a level surface.

There is a magnet attached t o the end of the

Remove the dipstick and check that the oil is

Make sure that no foreign material enters the

Reinstall the dipstick and fit the loop @ of

Specifications Model: VX500XTR

El Elevation - 3,500 ft,1,000 m 3,000 - 5,000 ft 4,500 - 7,000 ft 6,500 - 10,000 ft

Elevation Clutch setting Remark

Elevation Clutch setting Remark

Elevation - 3,500 ft/1,000 m 3,000 - 5,000 ft 4,500 - 7,000 ft 6,500 - 10,000 ft

Elevation , Clutch setting Remark

El Elevation - 3,500 W1,000 m 3,000 - 5,000 f? 4,500 - 7,000 f? 6,500 - 10,000 ft

Weight bushing Duralon t t t

Elevation Clutch setting Remark

Specifications Model: VX700XTCD

El Elevation - 3,500 ft/1,000 m 3,000 - 5,000 ft 4,500 - 7,000 ft 6,500 - 10,000 ft

Elevation Clutch setting Remark

El Elevation - 3,500 ft/1,000 m 3,000 - 5,000 ft 4,500 - 7,000 ft 6,500 - 10,000 ft

Elevation Clutch setting Remark

El Elevation - 3,500 ft/1,000 m 3,000 - 5,000 ft 4,500 - 7,000 ft 6,500 - 10,000 ft

Elevation Clutch setting Remark

Specifications Model: VT700

Elevation - 3,500 ft/1,000 m 3,000 - 5,000 ft 4,500 - 7,000 ft 6,500 - 10,000 ft

[H1 Sec. clutch shim 1.0 m m t c t

Elevation Clutch setting Remark

Clutch shifting speed

El Clutch engagement speed

Gear ratio chart

@ Chain and sprocket parts number:

* Not for reverse models

@ Secondary spring twist angle

@ Torque cam (secondary spring seat)

Be sure that the left and right spring preload is

Spring preload (VXGOOSX, VX700XTCl

Spring seat Standard

Be sure that the left and right spring preload is