This chapter of the Chery A15 maintenance manual provides general information about the engine:
1. It includes an engine assembly drawing and basic data on the 1.6L Tritec engine such as the number of cylinders, displacement, power and torque outputs.
2. The location of the engine serial number on the lower cylinder body is noted.
3. A diagram shows the layout of the transmission belt and the components it powers, and instructions are provided for replacing the belt and adjusting its tension.
This chapter of the Chery A15 maintenance manual provides general information about the engine:
1. It includes an engine assembly drawing and basic data on the 1.6L Tritec engine such as the number of cylinders, displacement, power and torque outputs.
2. The location of the engine serial number on the lower cylinder body is noted.
3. A diagram shows the layout of the transmission belt and the components it powers, and instructions are provided for replacing the belt and adjusting its tension.
This chapter of the Chery A15 maintenance manual provides general information about the engine:
1. It includes an engine assembly drawing and basic data on the 1.6L Tritec engine such as the number of cylinders, displacement, power and torque outputs.
2. The location of the engine serial number on the lower cylinder body is noted.
3. A diagram shows the layout of the transmission belt and the components it powers, and instructions are provided for replacing the belt and adjusting its tension.
This chapter of the Chery A15 maintenance manual provides general information about the engine:
1. It includes an engine assembly drawing and basic data on the 1.6L Tritec engine such as the number of cylinders, displacement, power and torque outputs.
2. The location of the engine serial number on the lower cylinder body is noted.
3. A diagram shows the layout of the transmission belt and the components it powers, and instructions are provided for replacing the belt and adjusting its tension.
Car model SQR7162 Engine model Tritec 1.6L Number of cylinders 4 Cylinder diameter (mm) 77 Stroke (mm) 85.8 Displacement (L) 1.6 Compression ratio 10.5 Ignition sequence 1–3–4–2 Engine property Net power: > 83KW @ 5600rpm Net torque: > 146 Nm @ 4500～5000 rpm Fuel consumption: < 341 g/KW*h (1600r/min, 2.4bar)
-1- Chery Automobile Co., Ltd.
Chery A15 Maintenance Manual
Three. Engine nameplate
The engine serial number is located on the lower cylinder body of the intake manifold.
Four. Transmission belt
1. Location of the transmission belt
1-Engine 1 2-Water pump/power steering pump 3-Compressor 4-Idle wheel 6 5-Crank shaft 2 6-Tensioner 4 5 3 2. Unfixing and replacing the transmission belt It is important to adjust the tension of the transmission belt in the case of replacement or adjustment of engine transmission belt. Overtension of the transmission belt will result in damaged AC generator and wheel bearing of the power steering pump belt while undertension will result in skidding or early abrasion. Reel the transmission belt on the belt wheel in a proper manner for replacement. Notice the reeling path of the transmission belt before its replacement. 1) Insert the tie-in of a pair of quick spanners into the belt tensioner.
-2- Chery Automobile Co., Ltd.
Chery A15 Maintenance Manual
2) Apply a torque of 98N (221bf) onto
the middle of the belt tensioner until it caves in for 9.0 -11.5mm (0.35-0.45in). 3) Press down the quick spanner in a reverse direction, release the tensioner and take out the old transmission belt. 4) Pay attention to the belt’s reeling direction during fixing, press down the quick spanner in a reverse direction and fix the transmission belt.
5) Release the tensioner and check if the
belt is properly located.
Note: Adjustment method for the
alignment of the transmission belt and tensioner assembly. - Turn the engine crank shaft’s belt wheel with a pair of spanners for over one round. - Observe the alignment of the transmission belt and tensioner assembly. If the center of transmission belt goes beyond the center of the tensioner assembly, unfix the latter and insert gasket to adjust.
