Nothing Special   »   [go: up one dir, main page]
Scribd Logo
Upload

Welcome to Scribd!

  • 118 views

    SERIES 599-Y2000: Features Product Description

    Uploaded by

    luismcmc

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    SERIES 599-Y2000: Features Product Description

    Uploaded by

    luismcmc
    118 views2 pages

    Original Title

    PPG_Y2000_Copper-TDS

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    118 views2 pages

    SERIES 599-Y2000: Features Product Description

    Uploaded by

    luismcmc

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    SERIES 599-Y2000

    Copper Conductive Coating

    Features Product Description

    SERIES 599-Y2000 A sprayable


    metallic coating system using a SYSTEM: One component, air dry.
    specially formulated non-oxidizing
    copper as the conductive agent. SOLIDS: 29% ± 2% by weight.
    Developed for use as an RFI and
    EMI shield for plastic electronic DENSITY: 8.5 ± .2 lbs. per gallon (1.02 ± 0.03 kg per liter)
    equipment housings. 599-Y2000
    can be used on acrylic, ABS and VISCOSITY @75°F ± 3°F (24°C ± 2°C): 19 ±2 Sec. (#2 EZ
    structural foams, e.g. Valox, etc. as Viscosity Cup - Mfr. Paul N. Gardner)
    well as solvent sensitive substrates
    such as polycarbonate and ADHESION: Excellent to most plastic substrates.
    polystyrene. For Noryl use 599-
    Y2000T (Y1371). ATTENUATION: More than 75 dB from 1 MHz to 1 Ghz.

    THINNER: Check viscosity after thorough mixing. Adjust to 19


    seconds (#2 EZ Viscosity Cup) with MEK, if
    necessary.

    APPLICATION HVLP or standard air gun with fluid recirculation


    METHOD: system is recommended. A pressure pot may be
    used provided that: (1) it has a large diameter,
    paddle-type agitator to keep copper in suspension
    and (2) a short translucent MEK-resistant fluid line
    of 1/8" (3.15 mm) ID or smaller is used (such as
    Binks Synflex) to prevent settling in the line.
    NOTE: The solvent system of this
    product is designed for fast drying DRYING TIME: 30 minutes flash off at room temperature; then 30
    and early measuring of conductivity. minutes @ 160°F. (71°C.) at 2.0 mils (50 microns).
    In hot, humid weather the fast drying Longer if thicker film, shorter if thinner film, to
    may result in sporadic blushing. achieve desired resistivity.
    Blushing is a whitening of the
    surface of the coating caused by HUMIDITY No change in resistivity or attenuation when tested
    condensation of water in a hot, RESISTANCE: in accordance with MIL-STD-202 Method 106 - 40
    humid environment. The addition of cycles; MIL-STD-810 Method 507 Procedure 5 -
    2-3% (3-4 ounces per gallon) of 480 hours cycling; Meets UL Specification 746-C
    Butyl Cellosolve(Ethylene-Glycol-
    Mono-Butyl-Ether) will eliminate
    blushing.

    PPG Industries, Inc.


    Springdale Plant The technical data presented in this bulletin is based upon information believed by PPG to be currently accurate.
    125 Colfax St. However, no guarantees of accuracy, comprehensiveness, or performance are given or implied. Continuous
    Springdale, PA 15144 improvements in coatings technology may cause future technical data to vary from what is in this bulletin. Contact your
    ppgindustrialcoatings.com PPG representative for the most up-to-date information.

    1. ©2014 PPG Industrial Coatings 02/19/2014

    /2014
    SERIES 599-Y2000
    Copper Conductive Coating

    SURFACE <0.05 ohms/sq. @ 1 mil (25 microns) DFT.


    RESISTIVITY: <0.025 ± 0.005 ohms/sq. @ 2 mils (50 microns) . These readings can be achieved under proper
    conditions: (1) properly mixed paint; (2) film is 100% dry.

    THEORETICAL 190.4 ft2. per gallon/ 1 mil (4.7m2/liter per 25 microns)


    COVERAGE: @ 100% transfer efficiency (computed on volume solids)

    STORAGE LIFE: Recommended storage in unopened containers is 12 months from date of


    shipment. Older material should have all Q.C. requirements rechecked before using.

    2 ©2014 PPG Industrial Coatings 02/19/2014

    /2014

    You might also like