The document summarizes installation and specifications for toggle bolts. Toggle bolts are spring wing hollow wall anchors designed for materials like hollow block, wallboard, and plaster. They consist of a machine screw and spring wing toggle in sizes from 1/8" x 2" to 1/2" x 6" with different head styles. To install, drill a hole slightly larger than the bolt in the base material, insert the bolt and thread on the wings, then tighten until firmly attached. Load capacity tables provide tension and shear ratings for different size anchors in gypsum wallboard from 3/8" to 3/4" thickness.
The document summarizes installation and specifications for toggle bolts. Toggle bolts are spring wing hollow wall anchors designed for materials like hollow block, wallboard, and plaster. They consist of a machine screw and spring wing toggle in sizes from 1/8" x 2" to 1/2" x 6" with different head styles. To install, drill a hole slightly larger than the bolt in the base material, insert the bolt and thread on the wings, then tighten until firmly attached. Load capacity tables provide tension and shear ratings for different size anchors in gypsum wallboard from 3/8" to 3/4" thickness.
The document summarizes installation and specifications for toggle bolts. Toggle bolts are spring wing hollow wall anchors designed for materials like hollow block, wallboard, and plaster. They consist of a machine screw and spring wing toggle in sizes from 1/8" x 2" to 1/2" x 6" with different head styles. To install, drill a hole slightly larger than the bolt in the base material, insert the bolt and thread on the wings, then tighten until firmly attached. Load capacity tables provide tension and shear ratings for different size anchors in gypsum wallboard from 3/8" to 3/4" thickness.
The document summarizes installation and specifications for toggle bolts. Toggle bolts are spring wing hollow wall anchors designed for materials like hollow block, wallboard, and plaster. They consist of a machine screw and spring wing toggle in sizes from 1/8" x 2" to 1/2" x 6" with different head styles. To install, drill a hole slightly larger than the bolt in the base material, insert the bolt and thread on the wings, then tighten until firmly attached. Load capacity tables provide tension and shear ratings for different size anchors in gypsum wallboard from 3/8" to 3/4" thickness.
MECHANICAL INSTALLATION PROCEDURES Drill the required hole through the base BASE MATERIAL material. The tolerances of the drill bit used Hollow Block, Wallboard, Plaster should meet the requirements of ANSI SIZE RANGE Standard B212.15. In denser materials such 1/8"x 2" to 1/2" x 6" ANCHOR MATERIAL as high strength concrete, drill the hole
Carbon Steel 1/16" larger.
PRODUCT DESCRIPTION The Toggle Bolt is a spring wing type hollow wall anchor designed for use in Insert bolt through fixture to be fastened, block, wallboard, and other hollow base materials. thread on wings, then fold wings completely back and insert through hole until wings spring open.
Round Head
Pull back on assembly to hold wings inside
wall to prevent the wings from spinning Flat Head while tightening bolt. Turn bolt with screwdriver until firmly tightened
Mushroom Head
ANCHOR SIZES AND STYLES
The following tables list the sizes and types of Toggle Bolt anchors. To determine the minimum bolt length required for the standard toggle, add the Slotted Hex Head thickness of the fixture, including any spacers or shims plus the thickness of the base material and the wing clearance. This will be the minimum bolt length required. CAT. NO. DRILL STD. STD. WT./ MUSH. SHH SIZE DIA. BOX CTN. 100
4023 4028 1/8" x 2" 3/8" 50 500 1-1/4
Tie Wire 4033 4038 1/8" x 3" 3/8" 50 500 1-1/2 4043 - 1/8" x 4" 3/8" 50 500 2 4133 - 3/16" x 3" 1/2" 50 500 4 4143 - 3/16" x 4" 1/2" 50 500 5 4233 - 1/4" x 3" 5/8" 50 500 6-1/2 4243 - 1/4" x 4" 5/8" 50 500 7-1/2 www.powers.com
The Toggle Bolt is a two-part assembly consisting of a machine screw and a CAT. NO. DRILL STD. STD. WT./ ROUND FLAT SIZE DIA. BOX CTN. 100 spring wing toggle. Sizes range from 1/8" x 2" to 1/2" x 6" with combo 4021 - 1/8" x 2" 3/8" 50 500 1-1/4 round, flat, mushroom, tie-wire or slotted hex head styles. 4031 4033 1/8" x 3" 3/8" 50 500 1-1/2 4041 4042 1/8" x 4" 3/8" 50 500 2 4121 - 3/16" x 2" 1/2" 50 500 3-1/4 US_DesignManual_Art 17/5/02 11:18 AM Page 118
118 MECHANICAL
CAT. NO. ROUND FLAT SIZE DRILL DIA. STD. BOX STD. CTN. WT./ 100 PERFORMANCE DATA 4131 4132 3/16" x 3" 1/2" 50 500 4 The following load capacities are based on testing conducted according to 4141 4142 3/16" x 4" 1/2" 50 500 5 ASTM Standard E 488. 4151 - 3/16" x 5" 1/2" 50 500 5-1/2 LOAD CAPACITIES IN GYPSUM WALLBOARD 4161 - 3/16" x 6" 1/2" 50 500 6-1/4 ANCHOR 3/8" WALLBOARD 1/2" WALLBOARD 5/8" WALLBOARD 3/4" WALLBOARD 4231 4232 1/4" x 3" 5/8" 50 500 6-1/2 SIZE TENSION SHEAR TENSION SHEAR TENSION SHEAR TENSION SHEAR (INCHES) (LBS.) (LBS.) (LBS.) (LBS.) (LBS.) (LBS.) (LBS.) (LBS.) 4241 4242 1/4" x 4" 5/8" 50 500 7-1/2 1/8" 150 180 200 205 250 265 290 310 4251 - 1/4" x 5" 5/8" 50 500 8-1/2 3/16" 170 210 245 280 315 350 385 420 4261 - 1/4" x 6" 5/8" 50 500 9-1/2 *1/4" 285 310 310 350 350 385 420 445 4331 - 5/16" x 3" 7/8" 25 250 13 5/16" 320 360 330 420 365 450 425 510 4341 - 5/16" x 4" 7/8" 25 250 14 3/8" 325 370 340 440 385 470 450 530 4351 - 5/16" x 5" 7/8" 25 250 16 1/2" 340 410 435 470 520 560 555 600 4361 - 5/16" x 6" 7/8" 25 250 18 4431 - 3/8" x 3" 7/8" 25 250 16 * Also applies to 1/4" Tie-Wire Toggle. 4441 - 3/8" x 4" 7/8" 25 250 18 NOTE: The values listed above are ultimate load capacities which should be reduced by a 4451 - 3/8" x 5" 7/8" 25 125 20 minimum safety factor of 4 or greater to determine the allowable working load. Since the 4461 - 3/8" x 6" 7/8" 25 125 23 consistency of gypsum wallboard varies greatly, these load capacities should be used as a 4541 - 1/2" x 4" 1-1/4" 25 25 42 guideline only. Job site tests should be conducted to determine the actual load capacities. 4561 - 1/2" x 6" 1-1/4" 25 25 50 LOAD CAPACITIES FOR C-90 HOLLOW BLOCK
C-90 HOLLOW BLOCK
TOGGLE WINGS ONLY ANCHOR DRILL TENSION SHEAR SIZE DIA. (LBS.) (LBS.) CAT. DRILL STD. STD. WT./ NO. SIZE DIA. BOX CTN. 100 1/8" 3/8" 270 270 4000 1/8" 3/8" 100 500 1 3/16" 1/2" 340 530 4020 3/16" 1/2" 100 1000 2 *1/4" 5/8" 560 890 4220 1/4" 5/8" 100 1000 3 5/16" 7/8" 775 1,020 4330 5/16" 7/8" 50 500 7 3/8" 7/8" 825 1,060 4430 3/8" 7/8" 50 500 7 1/2" 1-1/4" 1,305 1,200 4540 1/2" 1-1/4" 25 25 19 * Also applies to 1/4" Tie-Wire Toggle. NOTE: Depending upon anchor application and governing building code, ultimate load capacities TIE-WIRE ACOUSTICAL TOGGLE should be reduced by a minimum safety factor of 4 or greater to determine the allowable CAT. TIE WIRE DRILL STD. STD. WT./ working load. The design professional familiar with the actual product installation should be NO. SIZE HOLE SIZE DIA. BOX CTN. 100 consulted. Please refer to the general section entitled Evaluation of Test Data that appears earlier 4247 1/4" x 4" 7/32" 5/8" 100 100 9 in this manual for current industry standards. The consistency of C-90 hollow block varies greatly. 4257 1/4" x 5" 7/32" 5/8" 100 100 12 The load capacities listed above should be used as guidelines only. Job site tests should be conducted to verify base material consistency and actual anchor performance. INSTALLATION SPECIFICATIONS APPROVALS AND LISTINGS STANDARD TOGGLE The following approvals and listings are for reference purposes. They should be ANCHOR SIZE 1/8" 3/16" 1/4" 5/16" 3/8" 1/2" reviewed by the design professional responsible for the product installation to ANSI Drill Bit Size 3/8" 1/2" 5/8" 7/8" 7/8" 1-1/4" verify approved sizes, base materials, and compliance with local codes. Wing Clearance 1-1/16" 1-3/8" 1-1/2" 2-1/8" 2-1/8" 3" Federal Specification Thread Size 6-32 10-24 1/4-20 5/16-18 3/8-16 1/2-13 Standard Toggle Bolt anchors meet the descriptive requirements of FF-B-588D, Type 1, Class A, Style 1 (superseded). MATERIAL SPECIFICATIONS Tie Wire Toggle Bolt anchors meet the descriptive requirements of FF-B-588D, ANCHOR COMPONENT COMPONENT MATERIAL Type 1, Class A, Style 3 (superseded). Wing Body AISI 1010 1/8"-3/8" Trunnion Nut AISI 1010 SUGGESTED SPECIFICATION STANDARD TOGGLE 1/2" Trunnion Nut Zamac Alloy Bolt Carbon Steel - ANSI B18.6.3 Anchors for hollow walls shall be a two part assembly consisting of a machine Zinc Plating ASTM B633, SC 1, Type III (Fe/Zn 5) screw and a spring wing toggle. The machine screw shall meet the requirements of ANSI B18.6.3. The spring wing toggles shall consist of two “u" shaped stamped sheet metal wings which are mounted on a trunnion nut. The wings shall be held in the open position by a steel spring. Carbon steel components shall be plated according to ASTM Specification B633, SC1, Type III (Fe/Zn 5). Toggle-Bolt anchors shall be as dimensioned and supplied by Powers Fasteners Inc.
