Nothing Special   »   [go: up one dir, main page]
Scribd
Upload
249 views1 page

Automatic Battery Charger 27.6VDC 3A: General Information

Uploaded by

jose sedano

This automatic battery charger is designed to charge 12V lead acid batteries. It has a wide input voltage range of 100-240V AC and outputs 27.6V DC at 3A continuously. The charger maintains the battery fully charged without overcharging or gassing. It is protected from reverse polarity, short circuits, and overloads, and has an emergency charge fail alarm built in. Multiple units can be connected in parallel for higher current ratings.

Copyright:

© All Rights Reserved
Download as PDF, TXT or read online from Scribd
Download as pdf or txt

Automatic Battery Charger 27.6VDC 3A: General Information

Uploaded by

jose sedano
249 views1 page
This automatic battery charger is designed to charge 12V lead acid batteries. It has a wide input voltage range of 100-240V AC and outputs 27.6V DC at 3A continuously. The charger maintains the battery fully charged without overcharging or gassing. It is protected from reverse polarity, short circuits, and overloads, and has an emergency charge fail alarm built in. Multiple units can be connected in parallel for higher current ratings.

Original Title

SS3524

Copyright

© © All Rights Reserved

Available Formats

PDF, TXT or read online from Scribd

Did you find this document useful?

Is this content inappropriate?

This automatic battery charger is designed to charge 12V lead acid batteries. It has a wide input voltage range of 100-240V AC and outputs 27.6V DC at 3A continuously. The charger maintains the battery fully charged without overcharging or gassing. It is protected from reverse polarity, short circuits, and overloads, and has an emergency charge fail alarm built in. Multiple units can be connected in parallel for higher current ratings.

Copyright:

© All Rights Reserved
Download as PDF, TXT or read online from Scribd
Download as pdf or txt
249 views1 page

Automatic Battery Charger 27.6VDC 3A: General Information

Uploaded by

jose sedano
This automatic battery charger is designed to charge 12V lead acid batteries. It has a wide input voltage range of 100-240V AC and outputs 27.6V DC at 3A continuously. The charger maintains the battery fully charged without overcharging or gassing. It is protected from reverse polarity, short circuits, and overloads, and has an emergency charge fail alarm built in. Multiple units can be connected in parallel for higher current ratings.

Copyright:

© All Rights Reserved
Download as PDF, TXT or read online from Scribd
Download as pdf or txt
You are on page 1/ 1

27.

6VDC 3A
Automatic Battery Charger
GENERAL INFORMATION
Model SS3524 Intelligent Switch Mode Battery Charger
Is an easy to install compact charger specially intended for
use in gensets. It's wide input voltage range allows the
charger to be used in many different countries.
The charger is designed for permanent connection to
automotive batteries. It maintains the battery fully charged,
without overcharging or gassing. The charger is protected
from reverse polarity, short circuit and overloads.
Emergency Charge Fail Alarm is conveniently built in.
Multiple units may be connected in parallel in order to
obtain higher current ratings.

SPECIFICATIONS DANGER
Power supply : 100 ~ 240V, 45 ~ 65 Hz
DC Output : 27.6VDC 3ADC (continuously)
Charge Mode : Float 1. Danger: Potentially lethal voltages are present
DC Voltage Regulation : <1% inside the charger. Do not open case or attempt
Efficiency : >80% @full load to adjust or repair this unit.
Operating Temperature : 0 C ~ 40 C 2. Ventilate battery enclosure, batteries generate
Humidity : 0 ~ 90% Relative Humidity explosive hydrogen gas.
Vibration & Shock : 5 ~ 50Hz 2mm pk - pk 3. Avoid flames and sparks near batteries
50 ~ 100 Hz 1mm pk - pk 4. Avoid high humidity and corrosive gases near charger
100 mm drop onto chassis face 5. Minimum battery voltage must higher than 10 VDC or
Contact Capacity : 3A @240VAC the charger will automatically disconnect.
Protection : current limiting protection 6. This is not a power supply. Use only as a battery
short circuit protection charging.
reverse polarity protection
Weight : 0.72 Kgs (1.6 lbs)

INSTALLATION INSTRUCTIONS OUTLINE DRAWING


1. Use on a 2 x 12V Lead Acid Battery only
2. With Line power disconnected, connect Battery terminals
"+/-" to battery leads "+/-"

2.9"
3. Connect Line voltage to battery charger on lines L1 & L2,
form 100 to 240 Vac 50/60 Hz
4. Charging voltage should be 27.6+/-0.2VDC and the
indicate LED marked "ON" should illuminated when
power is ON

Caution! Crimp and property secure terminal lugs on to


power wires to avoid shorts
4.43"

6. With Power ON check charge current LED bar. The


2.61

current decreases as the battery charges.


ON 0.7 1.5 2.2 3.0
7. "0 A" indicates the battery is fully charged. TM
Attention
Battery Low
Charging Current (A)

9. Charger can remains connected during engine cranking 24V AUTOMATIC BATTERY CHARGER
Model Power In : 100 to 240
Output : 27.6 Vdc 3 Adc
SS3524
and running. Power
100 to
Charge Fail Relay

+
Output

L1 L2
10. Voltage sensing circuit automatically disconnect power
when the battery is fully charged.
11. Emergency Charge Fail Alarm Relay Available for use
4.72"
as part of a charge fail engine protection alarm.

McPherson@mtspowerproducts.com
www.mtspowerproducts.com
TM
McPherson 1.800-541-7677
Controls

You might also like