42REDP-Installation ORION

Installation and User's Guide
PREMIUM WIDE ASPECT RATIO SERIES

(42 inches)
http://www.orionimages.com
All contents of this document may change without prior notice, and actual product appearance may differ from that depicted herein
1. SAFETY INSTRUCTION
Follow this safety instruction to use the monitor properly and prevent the damages.
This safety instruction has “Warning” & “Caution” as below
Warning - If the user does not follow this instruction,

it may cause the serious damage to the user.
Caution - If the user does not follow this instruction, it may cause the slight
damage to the user or cause some damages to the monitor.
Keep this user’s guide book for later use.
Warning
Never remove the back over and Keep away the monitor from the
touch the inside of the monitor. direct sunlight and a heating appliance.
If you need a service, please
contact the service center.
Never push objects of any kind into Connect the power code to the wall
this product as they may result in outlet tightly. If the power code or plug
a risk of fire or electric shock. are defective and the wall outlet is not
tight, please do not use them.
2
Warning
Do not install this monitor on the outside For cleaning do not use liquid cleaners.
and near water. If may cause damage to Never touch the power plug with wet-hands.
the product, electric shock and fire.
When lightning and thundering, unplug the Unplug this product from the wall outlet, when
monitor from the wall outlet and never touch It does not operate for a long time.
it.
When smoking and noising from the monitor,

unplug the product from the wall outlet and
contact a service center.
WA R N I N G : How to fix
Do not open this product as it contains high voltage inside.
It may create an electric shock.
It the user disassembles and remove the back cover, it does not make sure
to make up for the damages and do a service and exchange the monitor.
3
Cautions
Install this monitor some distance Place this product on a stable place.
From the wall and do not install unless If not, it may fall, causing serious
Proper ventilation is provided. Damages to the monitor and people.
The openings must not be blocked by When carrying this monitor, be careful
curtain, rug or other similar surface. not to damage the panel and drop it
It may cause some trouble.
Before carrying the monitor, tum it off and Take the power plug out from the wall
Unplug the signal cables and the power code outlet.
From the wall outlet. Do not pull the cable. It may snap the inner-
wires and cause overheating and fire.
4
Cautions
Install this monitor about 50cm far from Do not press the LCD panel with hands or
the eyes and an angle of 0~15 degrees the sharpened material hardly.
below eyes. Too close installation may
cause having weak sight.
For cleaning, unplug the monitor from the Do not use the chemical liquid for cleaning.
Wall outlet. Do net use the liquid cloth. It may cause fading and breakage.
Use the soft cloth.
5
2. FCC RF INTERFERENCE STATEMENT

NOTE
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures.
Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio, TV technician for help.
Only shielded interface cable should be used.
Finally, any changes or modifications to the equipment by the user not expressly approved by the
grantee or manufacturer could void the users authority to operate such equipment.
DOC COMPLIANCE NOTICE

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus
set out in the radio interference regulation of Canadian Department of communications.
6
TABLE OF CONTENTS
1. SAFETY INSTRUCTION 2
1-1 Warning
1-2 Caution
2. FCC STATEMENT 6
3. INSTALLATION 8
3-1 Parts
3-2 How to Install
4. OSD MENU SETTING 12

5-1 Mode Setting
5-2 Menu Setting (VIDEO, S-VIDEO, COMPONENT Mode)
5-3 Menu Setting (VGA Mode)
5-4 Menu Setting (DVI, HDMI Mode)
5. FEATURES 32
6. LIMITED WARRANTY 33
7. TROUBLESHOOTING 34
7
3. INSTALLATION
3-1 Parts
LCD Monitor
VGA Cable Trigger Cable Power Cable
Battery Remote Controller User Manual
8
3-2 How to Install
KEY BUTTON
SHORT KEY FUNCTION

OSD Key Function
Activates and exit the OSD
Select input source, and select the OSD menu
Move the OSD menu and auto adjustment of RGB source
Decrease the level of volume and move the previous menu
Increase the level of volume and select rhe OSD menu
Turns the power ON or OFF. There will be a few seconds

delay before the display appears. The power LED (next to the
power switch) lights with green when the power is turned ON.
The power is turned off by pressing the power switch again
and the power LED goes red.
9
CONNECTION
1 2 3 4 5 6 7 8 9 10 11 12
1 HDMI 7 AUDIO (VIDEO-1 / S-VIDEO)

HDMI signal 1 / 2 input Stereo audio input for VIDEO-1 or S-VIDEO
2 DVI 8 S-VIDEO IN / OUT

DVI signal input S-VIDEO signal input / looping out
3 VGA 9 VIDEO-2 IN / OUT

VGA (PC RGB) signal input VIDEO-2 signal input / looping out
4 AUDIO (PC) 10 VIDEO-1 IN / OUT

Stereo audio input for VGA VIDEO-1 signal input / looping out
5 COMPONENT 11 TRIGGER
COMPONENT (Y/Pb/Pr) signal & stereo audio input TRIGGER signal input
6 AUDIO (VIDEO-2) 12 AC POWER

Stereo audio input for VIDEO-2 AC100~240V input
* 26" is located on the side of the product
10
REMOTE CONTROLLER
A MODE SELECT MENU

VIDEO1 VIDEO2
Select VIDEO1 mode Select VIDEO2 mode
S-VIDEO VGA (RGB)

POWER MUTE
Select S-VIDEO mode Select VGA mode
VIDEO1 VIDEO2 S-VIDEO

DVI HDMI1
Select DVI mode Select HDMI1 mode
VGA AUTO COLOR TEMP
A DVI HDMI1 COMPONENT

COMPONENT HDMI2
Select COMPONENT mode Select HDMI2 mode
HDMI2 S.SET
SCAN MODE PIP
B OSD CONTROL MENU

B VOL- VOL+
POWER MUTE
MENU/EXIT KEY LOCK Turn ON / OFF the monitor Turn ON / OFF the sound
AUTO COLOR TEMPERATURE

P.INPUT P.LOCATION P.SIZE
Auto adjust position of the screen (in VGA mode) Select color temperature of the screen
C P.SWAP STILL
SCAN MODE VOL- / VOL+
Select the scan mode of the screen Increase / Decrease the volume level
MENU / EXIT KEY LOCK

Activate and exit the OSD menu Locking the button (Prevent operation)
STILL
Freeze the current image
C PIP CONTROL MENU
S. SET PIP
Select between main and PIP audio input Activates PIP/PBP mode
P. INPUT P. LOCATION
Select an input source for PIP mode Select a location for PIP mode
P. SIZE P. SWAP
Select a size for PIP mode Swap between main and PIP input
11
4. OSD MENU SETTING
5-1 Mode Setting
INPUT 1. Use SOURCE button and then / button to move the

VIDEO1 source.
VIDEO2 2. Press the button to select the source.
S-VIDEO 3. Press the MENU/EXIT button to exit the INPUT menu.
√RGB PC
DVI
HDMI 1
HDMI 2
COMPONENT
▼/▲:MOVE ▶:ENTER
Inputs can be set to VIDEO1, VIDEO2, S-VIDEO, RGB PC, DVI, HDMI1, HDMI2 & COMPONENT mode
VIDEO1 VIDEO2
Select VIDEO1 mode Select VIDEO2 mode
S-VIDEO RGB PC
Select S-VIDEO mode Select VGA mode
DVI HDMI1
Select DVI mode Select HDMI1 mode
HDMI2 COMPONENT
Select HDMI2 mode Select COMPONENT mode
12
5-2 Menu Setting (VIDEO, S-VIDEO, COMPONENT Mode)
PICTURE
PICTURE PICTURE 1. Press the MENU/EXIT key to access menu.

CONTRAST 60% 2. Use the & arrow to highlight a selection.
SCREEN BRIGHTNESS 50%
COLOR 50% 3. Press the /SELECT to choose an item.
TINT 50%
SETUP SHARPNESS 50% 4. Use the & arrow to highlight a selection.
PEAKING CONTROL 50%
COLOR TEMP ◀ MEDIUM ▶
RGB RED 50%
5. Use the & arrow to adjust the setting on a
SETUP
GREEN 50% selected item.
BLUE 50%
CYCLE MODE SELECT ◀ 1080P ▶
SETUP
TRIGGER
▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : *.*
CONTRAST : Adjust visual color contrast BRIGHTNESS : Adjust color brightness

COLOR : Adjust visual color of screen TINT : Adjust tint of color
SHARPNESS : Adjust sharpness of screen COLOR TEMP : Switch color temperature of screen
CONTRAST BRIGHTNESS
PICTURE PICTURE PICTURE PICTURE
CONTRAST 60% CONTRAST 60%

SCREEN BRIGHTNESS 50% SCREEN BRIGHTNESS 50%
COLOR 50% COLOR 50%
TINT 50% TINT 50%
SETUP SHARPNESS 50% SETUP SHARPNESS 50%
PEAKING CONTROL 50% PEAKING CONTROL 50%
COLOR TEMP ◀ MEDIUM ▶ COLOR TEMP ◀ MEDIUM ▶
RGB RED 50% RGB RED 50%
SETUP SETUP
GREEN 50% GREEN 50%
BLUE 50% BLUE 50%
CYCLE MODE SELECT ◀ 1080P ▶ CYCLE MODE SELECT ◀ 1080P ▶
SETUP SETUP
TRIGGER TRIGGER
▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : *.* ▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : *.*
Default setting is 60% and adjustable from range of 0 to 100% Default setting is 50% and adjustable from range of 0 to 100%
13
COLOR TINT

COLOR 50% COLOR 50%
TINT 50% TINT 50%
SETUP SETUP
GREEN 50% GREEN 50%
BLUE 50% BLUE 50%
SETUP SETUP
TRIGGER TRIGGER
SHARPNESS COLOR TEMP

COLOR 50% COLOR 50%
TINT 50% TINT 50%
SETUP SETUP
GREEN 50% GREEN 50%
BLUE 50% BLUE 50%
SETUP SETUP
TRIGGER TRIGGER
Default setting is 50% and adjustable from range of 0 to 100% Default setting is MEDIUM and switch to WARM, USER and
COOL color temperature options
USER - Default setting of RED, GREEN, BLUE is 50% and

adjustable from range of 0 to 100%
14
SCREEN
PICTURE SCREEN 1. Press the MENU/EXIT key to access menu.

SCAN MODE ◀ FULL ▶ 2. Use the & arrow to highlight a selection.
SCREEN PIP ◀ OFF ▶
PIP INPUT ◀ VIDEO2 ▶ 3. Press the /SELECT to choose an item.
PIP SWAP ▶
SETUP PIP SIZE ◀ SMALL ▶
PIP R/T ◀ R/B ▶
4. Use the & arrow to highlight a selection.
RGB 5. Use the & arrow to adjust the setting on a
SETUP
selected item.
CYCLE
SETUP
TRIGGER
SCAN MODE : Select the scan mode of the screen PIP : Activates PIP/PBP mode
PIP, PBP - COMBINATION OF SIGNAL INPUT

SUB VIDEO-1 VIDEO-2 S-VIDEO COMPONENT VGA DVI HDMI
MAIN
VIDEO-1 X O O X X X X
VIDEO-2 O X O X X X X
S-VIDEO O O X X X X X
COMPONENT O O O X X X X
VGA O O O X X X X
DVI O O O X X X X
HDMI O O O X X X X
SCAN MODE PIP
PICTURE SCREEN PICTURE SCREEN
SCAN MODE ◀ FULL ▶ SCAN MODE ◀ FULL ▶

SCREEN PIP ◀ OFF ▶ SCREEN PIP ◀ OFF ▶
PIP INPUT ◀ VIDEO2 ▶ PIP INPUT ◀ VIDEO2 ▶
PIP SWAP ▶ PIP SWAP ▶
SETUP PIP SIZE ◀ SMALL ▶ SETUP PIP SIZE ◀ SMALL ▶
PIP R/T ◀ R/B ▶ PIP R/T ◀ R/B ▶
RGB RGB
SETUP SETUP
CYCLE CYCLE
SETUP SETUP
TRIGGER TRIGGER
Default setting is FULL and switch to UNDER, OVER and 4:3 Default setting is OFF and switch to ON, DW1 and DW2
scan mode options PIP/PBP mode options
ON - PIP INPUT : Select an input source for PIP mode
(VIDEO1, VIDEO2, S-VIDEO)
PIP SWAP : Swap between main and PIP input
PIP SIZE : Select a size for PIP mode
(SMALL, NORMAL, LARGE)
PIP R/T : Select a location for PIP mode
(R/B, L/B)
15
SETUP
PICTURE SETUP 1. Press the MENU/EXIT key to access menu.

INPUT ◀ VIDEO1 ▶ 2. Use the & arrow to highlight a selection.
SCREEN LANGUAGE ◀ ENGLISH ▶
SOUND MUTE ◀ OFF ▶ 3. Press the /SELECT to choose an item.
BUTTON LOCK ◀ OFF ▶
SETUP NOISE REDUCTION ◀ ON ▶
OSD TIME 15s
DEFAULT ▶
RGB LINE SHIFT ◀ OFF ▶ 5. Use the & arrow to adjust the setting on a
SETUP
selected item.
CYCLE
SETUP
TRIGGER
INPUT : Select an input source for main screen LANGUAGE : Set to different language mode
SOUND MUTE : Turn on/off the sound BUTTON LOCK : Locking the button (Prevent operation)
NOISE REDUCTION : Set a noise reduction mode OSD TIME : Set a time duration of OSD menu
DEFAULT : Factory default setting LINE SHIFT : Move a little to protect the screen
INPUT LANGUAGE
PICTURE SETUP PICTURE SETUP
INPUT ◀ VIDEO1 ▶ INPUT ◀ VIDEO1 ▶

SCREEN LANGUAGE ◀ ENGLISH ▶ SCREEN LANGUAGE ◀ ENGLISH ▶
SOUND MUTE ◀ OFF ▶ SOUND MUTE ◀ OFF ▶
BUTTON LOCK ◀ OFF ▶ BUTTON LOCK ◀ OFF ▶
SETUP NOISE REDUCTION ◀ ON ▶ SETUP NOISE REDUCTION ◀ ON ▶
OSD TIME 15s OSD TIME 15s
DEFAULT ▶ DEFAULT ▶
RGB LINE SHIFT ◀ OFF ▶ RGB LINE SHIFT ◀ OFF ▶
SETUP SETUP
CYCLE CYCLE
SETUP SETUP
TRIGGER TRIGGER
Inputs can be set to VIDEO1, VIDEO2, S-VIDEO, RGB PC, Default setting is ENGLISH and language setting can be set
DVI, HDMI1, HDMI2 and COMPONENT mode to ITALIAN, FRENCH, SPANISH and GERMAN
16
SOUND MUTE BUTTON LOCK

SETUP SETUP
CYCLE CYCLE
SETUP SETUP
TRIGGER TRIGGER
Default setting is OFF and switch to ON sound mute option Default setting is OFF and switch to ON button lock option
Release the lock - Press KEY LOCK button on the remote control
- Press & button on the key pad
NOISE REDUCTION OSD TIME

SETUP SETUP
CYCLE CYCLE
SETUP SETUP
TRIGGER TRIGGER
Default setting is ON and switch to OFF noise reduction option Default setting is 15s and adjustable from range of 5 to 30s
17
DEFAULT LINE SHIFT

RGB LINE SHIFT ◀ OFF ▶ RGB LINE SHIFT ◀ ON ▶
SETUP SETUP
CYCLE CYCLE
SETUP SETUP
TRIGGER TRIGGER
DEFAULT is set OSD menu to factory default Default setting is ON and switch to OFF line shift option
18
CYCLE SETUP
PICTURE CYCLE SETUP 1. Press the MENU/EXIT key to access menu.

CYCLE TIME 10s 2. Use the & arrow to highlight a selection.
SCREEN CYCLE ◀ OFF ▶
VIDEO1 ◀ OFF ▶
▶
3. Press the /SELECT to choose an item.
VIDEO2 ◀ OFF
S-VIDEO ◀ OFF ▶
SETUP
RGB PC ◀ OFF ▶
DVI ◀ OFF ▶
RGB HDMI 1 ◀ OFF ▶ 5. Use the & arrow to adjust the setting on a
SETUP
HDMI 2 ◀ OFF ▶ selected item.
COMPONENT ◀ OFF ▶
CYCLE
SETUP
TRIGGER
CYCLE TIME : Adjust cycle time to displayed on the screen CYCLE : Selected mode keep change continuously
CYCLE TIME CYCLE
PICTURE CYCLE SETUP PICTURE CYCLE SETUP
CYCLE TIME 10s CYCLE TIME 10s

SCREEN CYCLE ◀ OFF ▶ SCREEN CYCLE ◀ OFF ▶
VIDEO1 ◀ OFF ▶ VIDEO1 ◀ OFF ▶
VIDEO2 ◀ OFF ▶ VIDEO2 ◀ OFF ▶
SETUP S-VIDEO ◀ OFF ▶ SETUP S-VIDEO ◀ OFF ▶
RGB PC ◀ OFF ▶ RGB PC ◀ OFF ▶
DVI ◀ OFF ▶ DVI ◀ OFF ▶
RGB HDMI 1 ◀ OFF ▶ RGB HDMI 1 ◀ OFF ▶
SETUP SETUP
HDMI 2 ◀ OFF ▶ HDMI 2 ◀ OFF ▶
COMPONENT ◀ OFF ▶ COMPONENT ◀ OFF ▶
CYCLE CYCLE
SETUP SETUP
TRIGGER TRIGGER
Default setting is 10s and adjustable from range of 10 to 30s Default setting is OFF and switch to ON cycle option
19
TRIGGER
PICTURE TRIGGER 1. Press the MENU/EXIT key to access menu.

TRIGGER MODE ◀ OFF ▶ 2. Use the & arrow to highlight a selection.
SCREEN TRIGGER INPUT ◀ VIDEO1 ▶
TRIGGER DWELL 10s 3. Press the /SELECT to choose an item.
SETUP 4. Use the & arrow to highlight a selection.
SETUP
selected item.
CYCLE
SETUP
TRIGGER
TRIGGER MODE : Set the trigger mode TRIGGER INPUT : Select the input source of trigger mode
TRIGGER DWELL : Set the display time of trigger mode
TRIGGER MODE TRIGGER INPUT
PICTURE TRIGGER PICTURE TRIGGER
TRIGGER MODE ◀ OFF ▶ TRIGGER MODE ◀ OFF ▶

SCREEN TRIGGER INPUT ◀ VIDEO1 ▶ SCREEN TRIGGER INPUT ◀ VIDEO1 ▶
TRIGGER DWELL 10s TRIGGER DWELL 10s
SETUP SETUP
RGB RGB
SETUP SETUP
CYCLE CYCLE
SETUP SETUP
TRIGGER TRIGGER
Default setting is OFF and switch to ON trigger mode Inputs can be set to VIDEO1, VIDEO2 and S-VIDEO mode
TRIGGER DWELL
PICTURE TRIGGER
TRIGGER MODE ◀ OFF ▶

TRIGGER DWELL 10s
SETUP
RGB
SETUP
CYCLE
SETUP
TRIGGER
Default setting is 10s and adjustable from range of 10 to 60s
20
5-3 Menu Setting (VGA Mode)
PICTURE

TINT 50%
PEAKING CONTROL 50%
RGB RED 50%
SETUP
BLUE 50%
SETUP
TRIGGER

COLOR TEMP : Switch color temperature of screen
CONTRAST BRIGHTNESS

COLOR 50% COLOR 50%
TINT 50% TINT 50%
SETUP SETUP
GREEN 50% GREEN 50%
BLUE 50% BLUE 50%
SETUP SETUP
TRIGGER TRIGGER
21
COLOR TEMP
PICTURE PICTURE
CONTRAST 60%
COLOR 50%
TINT 50%
SETUP SHARPNESS 50%
PEAKING CONTROL 50%
RGB RED 50%
SETUP
GREEN 50%
BLUE 50%
SETUP
TRIGGER
Default setting is MEDIUM and switch to WARM, USER and

COOL color temperature options
USER - Default setting of RED, GREEN, BLUE is 50% and

SCREEN

PIP SWAP ▶
PIP R/T ◀ R/B ▶
SETUP
selected item.
CYCLE
SETUP
TRIGGER
PIP : Activates PIP/PBP mode
22
PIP
PICTURE SCREEN
SCAN MODE ◀ FULL ▶

PIP INPUT ◀ VIDEO2 ▶
PIP SWAP ▶
PIP R/T ◀ R/B ▶
RGB
SETUP
CYCLE
SETUP
TRIGGER
Default setting is OFF and switch to ON, DW1 and DW2

PIP/PBP mode options
ON - PIP INPUT : Select an input source for PIP mode

(VIDEO1, VIDEO2, S-VIDEO)
PIP SWAP : Swap between main and PIP input
PIP SIZE : Select a size for PIP mode
(SMALL, NORMAL, LARGE)
PIP R/T : Select a location for PIP mode
(R/B, L/B)
SETUP

OSD TIME 15s
DEFAULT ▶
SETUP
selected item.
CYCLE
SETUP
TRIGGER
This function of each menu is listed page 16

Please refer to page 16 for SETUP menu
23
RGB SETUP
PICTURE RGB SETUP 1. Press the MENU/EXIT key to access menu.

H-POSITION 100% 2. Use the & arrow to highlight a selection.
SCREEN V-POSITION 0%
CLOCK 0% 3. Press the /SELECT to choose an item.
PHASE 0%
AUTO ADJUST ▶
SETUP
POWER SAVING ◀ OFF ▶
AUTO REPEAT ◀ OFF ▶
SETUP
selected item.
CYCLE
SETUP
TRIGGER
H-POSITION : Adjust horizontal position of monitor V-POSITION : Adjust vertical position of monitor
CLOCK : Adjust clock of monitor PHASE : Adjust phase of monitor
AUTO ADJUST : Auto adjust position of screen POWER SAVING : Power saving mode
AUTO REPEAT : Adjust auto repeat of monitor
H-POSITION V-POSITION
PICTURE RGB SETUP PICTURE RGB SETUP
H-POSITION 100% H-POSITION 100%

SCREEN V-POSITION 0% SCREEN V-POSITION 0%
CLOCK 0% CLOCK 0%
PHASE 0% PHASE 0%
SETUP AUTO ADJUST ▶ SETUP AUTO ADJUST ▶
POWER SAVING ◀ OFF ▶ POWER SAVING ◀ OFF ▶
AUTO REPEAT ◀ OFF ▶ AUTO REPEAT ◀ OFF ▶
RGB RGB
SETUP SETUP
CYCLE CYCLE
SETUP SETUP
TRIGGER TRIGGER
Can be set between 0 to 100% horizontal position of monitor Can be set between 0 to 100% vertical position of monitor
by manually by manually
24
CLOCK PHASE

CLOCK 0% CLOCK 0%
PHASE 0% PHASE 0%
RGB RGB
SETUP SETUP
CYCLE CYCLE
SETUP SETUP
TRIGGER TRIGGER
Can be set between 0 to 100% clock of monitor by manually Can be set between 0 to 100% phase of monitor by manually
AUTO ADJUST POWER SAVING

CLOCK 0% CLOCK 0%
PHASE 0% PHASE 0%
RGB RGB
SETUP SETUP
CYCLE CYCLE
SETUP SETUP
TRIGGER TRIGGER
Auto adjust position and image of screen Default setting is OFF and switch to ON power saving mode
AUTO REPEAT
PICTURE RGB SETUP
H-POSITION 100%
SCREEN V-POSITION 0%
CLOCK 0%
PHASE 0%
SETUP AUTO ADJUST ▶
POWER SAVING ◀ OFF ▶
AUTO REPEAT ◀ OFF ▶
RGB
SETUP
CYCLE
SETUP
TRIGGER
Default setting is OFF and switch to ON auto repeat mode
25
CYCLE SETUP

VIDEO1 ◀ OFF ▶
▶
VIDEO2 ◀ OFF
S-VIDEO ◀ OFF ▶
SETUP
RGB PC ◀ OFF ▶
DVI ◀ OFF ▶
SETUP
CYCLE
SETUP
TRIGGER

Please refer to page 19 for CYCLE SETUP menu
TRIGGER

SETUP
selected item.
CYCLE
SETUP
TRIGGER

Please refer to page 20 for TRIGGER menu
26
VGA / DVI / HDMI Mode Tables
VGA / DVI Mode

MODE RESOLUTION VERTICAL FREQUENCY (Hz)
720X400 70
VGA
640X480 60 / 72 75
SVGA 800X600 50 / 60 / 72 / 75
XGA 1024X768 50 / 60 / 75
WXGA 1366X768 60
UXGA 1600X1200 60
HD 1920X1080 60
HDMI Mode
MODE RESOLUTION VERTICAL FREQUENCY (Hz)
EDTV 480i 720X480 30
EDTV 576i 720X576 25
SDTV 480p 720X480 60
SDTV 576p 720X576 60
HDTV 720p 1280X720 50 / 60
HDTV 1080i 1920X1080 30 / 25
HDTV 1080p 1920X1080 50 / 60
Note : Not all resolutions generated by your video source are available on the monitor.
27
5-4 Menu Setting (DVI, HDMI Mode)
PICTURE

TINT 50%
PEAKING CONTROL 50%
RGB RED 50%
SETUP
BLUE 50%
SETUP
TRIGGER

COLOR : Adjust visual color of screen TINT : Adjust tint of color
SHARPNESS : Adjust sharpness of screen COLOR TEMP : Switch color temperature of screen
CONTRAST BRIGHTNESS

COLOR 50% COLOR 50%
TINT 50% TINT 50%
SETUP SETUP
GREEN 50% GREEN 50%
BLUE 50% BLUE 50%
SETUP SETUP
TRIGGER TRIGGER
28
COLOR TINT

COLOR 50% COLOR 50%
TINT 50% TINT 50%
SETUP SETUP
GREEN 50% GREEN 50%
BLUE 50% BLUE 50%
SETUP SETUP
TRIGGER TRIGGER
SHARPNESS PEAKING CONTROL

COLOR 50% COLOR 50%
TINT 50% TINT 50%
SETUP SETUP
GREEN 50% GREEN 50%
BLUE 50% BLUE 50%
SETUP SETUP
TRIGGER TRIGGER
COLOR TEMP MODE SELECT

COLOR 50% COLOR 50%
TINT 50% TINT 50%
SETUP SETUP
GREEN 50% GREEN 50%
BLUE 50% BLUE 50%
SETUP SETUP
TRIGGER TRIGGER
Default setting is MEDIUM and switch to WARM, USER and Default setting is 1080p and switch to 1920X1080 mode
COOL color temperature options 1080P - Bluray, DVD player and AV video equipment (2% Over Scan)
USER - Default setting of RED, GREEN, BLUE is 50% and 1920X1080 - It is the fit image on PC In (Just/Real Scan)
29
SCREEN

PIP SWAP ▶
PIP R/T ◀ R/B ▶
SETUP
selected item.
CYCLE
SETUP
TRIGGER

Please refer to page 22 for SCREEN menu
SETUP

OSD TIME 15s
DEFAULT ▶
SETUP
selected item.
CYCLE
SETUP
TRIGGER

Please refer to page 16 for SETUP menu
30
CYCLE SETUP

VIDEO1 ◀ OFF ▶
▶
VIDEO2 ◀ OFF
S-VIDEO ◀ OFF ▶
SETUP
RGB PC ◀ OFF ▶
DVI ◀ OFF ▶
SETUP
CYCLE
SETUP
TRIGGER

Please refer to page 19 for CYCLE SETUP menu
TRIGGER

SETUP
selected item.
CYCLE
SETUP
TRIGGER

Please refer to page 20 for TRIGGER menu
31
5. FEATURE
General Features 42REDP

Screen Size 42.0 inches
Resolution 1920*1080 pixels
Pixel Pitch 0.485*0.485 mm
Brightness 400 cd/m^2
Contrast Ratio 4000:1
Display Aspect Ratio 16:9
Viewing Angle (H/V) 178/178 degrees
Display Color 16.7 million
Response Time 6.5 ms
Video System NTSC/PAL
Panel Life Time (hours) 50,000 hours
Video In/Out (BNC Type) 2/2
S-Video In/Out 1/1
VGA In (15Pin D-Sub) 1
Interface Component 1
DVI In/HDMI In 1/2
Audio In (RCA Type) 3
PC Stereo In 1
Audio Built in Speakers Y (7.5W*2)
Transmitter Remote Control Y
PIP/PBP
Multi Display Function
Dual Composite Display
Filter Type 3D Comb Filter
Deinterlacing Y
Special
Trigger Source Switching Y (NO/NC)
Features
LCD Protection Glass N
Noise reduction Y
Auto source sequencing Y
Multi Lingual Language Eng, Spa, Fre, Ger, Ita
Dimension Outline Dimension (w Stand) 38.8*9.4*24.7 inches
Cabinet color/Base Stand Black/Desktop Stand
Cabinet
Cabinet Material Electro-Galvanized Steel
Consumption <200 watts
Power
Electrical Ratings AC 100~240 V (50/60Hz)
Operating Temperature -5~50 celsius
Circumstance
Storage Temperature -20~60 celsius
VESA Mounts Size 400*300 mm
Mounts Ceiling Mount CMH-01
Wall WB-2642
32
6. 2Year Limited Warranty
All ORION Images products carry a limited warranty from ship date against defects in materials and
workmanship. ORION Images is not liable for improper installation that results in damage to mounts,
adapters, display equipment or personal injury.
Contact ORION Images

In the event of missing and/or damage equipment, or technical questions, the following information can
help in the completion of the installation.
Address: 7300 Bolsa Avenue, Westminster, CA 92683

Tel: 714-766-6300 / Fax: 714-766-6310
Email: sales@orionimages.com
Website: http://www.orionimages.com
33
7. TROUBLESHOOTING
* When the following troubles are occurred, follow the trouble shooting. Before contacting a
service center.
Troubleshooting Troubleshooting Tip
1. Make sure if the power supply is connected property

The screen doesn’t
2. Turn on the power.
show up
3. Select the input signal right for the connected port.
The screen is too light

Control the BRIGHTNESS
or to dark
The screen size is not fit Press the AUTO key among keys in the front.
for the PC signal (It is used only in the PC signal)
The screen color shows In the FUNCTION menu of OSD menu, perform the
strange in the PC signal AUTOADJUST.
34
MEMO
35

42REDP-Installation ORION

Uploaded by

Copyright:

Available Formats

42REDP-Installation ORION

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

42REDP-Installation ORION

Uploaded by

Copyright:

Available Formats

Installation and User's Guide

PREMIUM WIDE ASPECT RATIO SERIES

This safety instruction has “Warning” & “Caution” as below

Warning - If the user does not follow this instruction,

Keep this user’s guide book for later use.

When smoking and noising from the monitor,

2. FCC RF INTERFERENCE STATEMENT

Reorient or relocate the receiving antenna.

DOC COMPLIANCE NOTICE

4. OSD MENU SETTING 12

VGA Cable Trigger Cable Power Cable

Battery Remote Controller User Manual

3-2 How to Install

SHORT KEY FUNCTION

Turns the power ON or OFF. There will be a few seconds

1 HDMI 7 AUDIO (VIDEO-1 / S-VIDEO)

2 DVI 8 S-VIDEO IN / OUT

3 VGA 9 VIDEO-2 IN / OUT

4 AUDIO (PC) 10 VIDEO-1 IN / OUT

6 AUDIO (VIDEO-2) 12 AC POWER

A MODE SELECT MENU

S-VIDEO VGA (RGB)

VIDEO1 VIDEO2 S-VIDEO

A DVI HDMI1 COMPONENT

SCAN MODE PIP

B OSD CONTROL MENU

AUTO COLOR TEMPERATURE

MENU / EXIT KEY LOCK

C PIP CONTROL MENU

4. OSD MENU SETTING

5-1 Mode Setting

INPUT 1. Use SOURCE button and then / button to move the

5-2 Menu Setting (VIDEO, S-VIDEO, COMPONENT Mode)

PICTURE PICTURE 1. Press the MENU/EXIT key to access menu.

▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : *.*

CONTRAST : Adjust visual color contrast BRIGHTNESS : Adjust color brightness

PICTURE PICTURE PICTURE PICTURE

CONTRAST 60% CONTRAST 60%

PICTURE PICTURE PICTURE PICTURE

CONTRAST 60% CONTRAST 60%

SHARPNESS COLOR TEMP

PICTURE PICTURE PICTURE PICTURE

CONTRAST 60% CONTRAST 60%

USER - Default setting of RED, GREEN, BLUE is 50% and

PICTURE SCREEN 1. Press the MENU/EXIT key to access menu.

▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : *.*

PIP, PBP - COMBINATION OF SIGNAL INPUT

SCAN MODE PIP

PICTURE SCREEN PICTURE SCREEN

SCAN MODE ◀ FULL ▶ SCAN MODE ◀ FULL ▶

PICTURE SETUP 1. Press the MENU/EXIT key to access menu.

▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : *.*

PICTURE SETUP PICTURE SETUP

INPUT ◀ VIDEO1 ▶ INPUT ◀ VIDEO1 ▶

SOUND MUTE BUTTON LOCK

PICTURE SETUP PICTURE SETUP

INPUT ◀ VIDEO1 ▶ INPUT ◀ VIDEO1 ▶

NOISE REDUCTION OSD TIME

PICTURE SETUP PICTURE SETUP

▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : .

▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : .

▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : .

▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : .

▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : .

▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : .

▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : .

▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : .

▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : .

▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : .

▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : .

▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : .

▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : .

▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : .

▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : .

▼/▲ : MOVE ◀/▶ : ADJUST ▶ : ENTER MENU : EXIT VER : .