SEPB201301

Service Technology Development Group

EMMS: Equipment Management Monitoring System Customer Support Division

◇ Enter ν Exit Left ＜ ＞ Right

The machine monitor is equipped with ＜

two functions, Operator Mode, and Enter to Change
◇ change #
ν Exit ◇ ν Exit
Service Mode 1, & 2. In order to access Language
these functions the ignition key must Scroll through
＜ 8 languages ＞
be in the “ON” position.
ENTER ◇ ◇ Sets a Language
Increase #
＜ Decrease # ＞
Move Move right
ν ◇
EXIT ν left or set # ＞

＜ ν ◇

Read only function

＜ Scroll ＞
After selection
ν ◇

Yes ＜ or ＞ No

ν Reset system

If an action code occurs, the degree of the fault is automatically displayed as a user code on the machine
monitor and an alarm will also sound. Appropriate action for the operator will be displayed in two ways.
This display is to alert the
Shut the machine down operator of the remaining
When a failure occurs check immediately and call your time before service is due on
the system being displayed dealer phone number a system

1
 SEPB201301
Service Technology Development Group
EMMS: Equipment Management Monitoring System Customer Support Division

＜
To access the Service Mode 1, the
ignition key must be in the “ON” ＞
position and the access ID entered. ◇ ν ◇ ν

Scroll through Scroll through

＜ fault codes ＞ ＜ fault codes ＞
ν ＜
Hold the two switches down ν ◇ This is a read only function
simultaneously for approx. 6 sec.
then enter ID number. Or

Access ID numbers: 6491

Yes ＜ or ＞ No ν ◇
Clears one
ν
code only
Decrease # ＜ ＞ Increase #
Yes ＜ or ＞ No
Move cursor Move cursor
to the left ν ◇ Clears all
to the right ν
codes

＜ ＞
You can take a
ν ◇ snapshot in any ◇
◇ ENTER system …………………
ν

◇
Scroll through
＜ ＞ ＜ 19 items
＞
ν

◇
Scroll through
＜ ＞ ＜ 79 items
＞
ν

◇
Scroll through
＜ ＞ ＜ 11 items
＞
ν

◇
Scroll through
＜ ＞ ＜ 47 items ＞
ν

◇
Increase #
These are read only functions. ＜ Decrease # ＞
In (2 ITEMS) you can monitor
two systems simultaneously. Move Move right
ν ◇
left or set #
2

To exit system: ν
 SEPB201301
Service Technology Development Group
EMMS: Equipment Management Monitoring System Customer Support Division

ν ◇

Through the transmission controller the machine monitor can carry out the
adjustment functions to correct the differences in the operation feel to a constant
level caused by the individual differences in the ECMV. It can also carry out the
self adjustment learning function so that a constant gearshift feeling is maintained
in accordance with the wear of the transmission clutches. When the following
operations related to the power train have been carried out, perform the
adjustments.
•When the transmission has been overhauled or the valve body is replaced.
•When a failure code or repair in the speed sensor occurs (see chart).
•When a failure code appears for the transmission oil temp. sensor (see chart).
•When the transmission oil filter becomes clogged and replaced (see chart).

＞
ν ◇ ν ◇

ν ◇ ν ◇

This function is for Yes ＜ or ＞ No ＜ ＞

factory use only.
ν

ν ◇

See Service Manual

section 20 for details.
When replacing the monitor
the system data must be reset
to the current machines ν
data. These include:
◇
1. Service meter data.
2. Odometer data.
3. Reverse travel data. Scroll through
＜ 12 items ＞
Never use this function except After selection
When replacing the machines ν
monitor. See service manual
◇
Section 20 for procedures.

Increase #
＜ Decrease # ＞
Move Move right
ν ◇
left or set # In this feature you can change the
service intervals for the listed items.
3
ν Resets
Yes ＜ or ＞ No
system
4
5
6
7
8
9
10
11
12
13
14
15
16