099 Viscocrete-10
099 Viscocrete-10
099 Viscocrete-10
Edition 3, 2007
Identification no.
02 01 01 01 200 0 000097
Version no. 0010
Sika® Viscocrete®-10
Sika Viscocrete - 10
® ®
® ®
Construction
Description Sika Viscocrete -10 is a third generation superplasticiser for concrete and
mortar. It is particularly developed for the production of high flow concrete with
exceptional flow retention properties.
Complies with A.S.T.M. C 494-92 Type F
® ®
Uses Sika Viscocrete -10 is especially suitable for concrete mixes with prolonged
transportation time and long workability, powerful water reduction and excellent
flowability.
® ®
Sika Viscocrete -10 is suitable for the production of both precast concrete and
ready mix concrete.
Sika Viscocrete facilities extreme water reduction, excellent flowability with the
same time optimal cohesion and highest self compacting behaviour.
Product Data
Appearance / Colour Turbid Whitish Liquid
Back
Table of Contents
Storage Condition / Dry, shaded place, Protect from direct sunlight and frost.
Technical Data
Chemical Base Modified polycarboxylate in water
Density Specific density: approx. 1.06 kg/l (at +20°C)
pH-Value 4.25 ± 0.5
System Information
Dosage Recommended dosage for a concrete with high workability
For soft plastic concrete 0.2 – 0.6% by weight of
binder
For flowing and self compacting concrete (S.C.C.) 0.5 – 1.8% by weight of
binder
® ®
Application Sika Viscocrete -10 may be combined with the following products :
Conditions / Limits Plastocrete R
Plastiment RTD-01
Plastiment VZ
SikaFume
Sika AER
Pre-trials are recommend if combinations with the above products are required.
Please consult our Technical Service Department.
Application Instructions
Dispensing Sika®Viscocrete® -10 is added to the gauging water or simultaneously added
with water into the concrete mixer.
To take advantage of the high water reduction, a wet mixing time of at least 60
seconds is recommended.
To avoid excess water in the concrete, final dosage must start after 2/3 of wet
mixing time only.
Application Method / Tools The standard rules of good concreting practice, concerning production as well
as placing, are to be followed.
Fresh concrete must be cured properly and as early as possible.
Cleaning of Tools Clean all tools and application equipment with water immediately after use.
Hardened/cured material can only be mechanically removed.
Notes on Application Limits If frozen and/or if precipitation has occurred, Sika®Viscocrete® -10 may be
used after thawing slowly at room temperature and after intensive mixing.
Protective Measure Upon contact with skin, wash off with water and soap. In case on contact with
eyes or mucous membrane, rinse immediately with clean water and seek
medical attention without delay.
Important Notes All technical data stated in this Product Data Sheet are based on laboratory
tests. Actual data may vary due to changing conditions beyond our control.
Branches
PT. Sika Indonesia Surabaya :
Jl. Raya Cibinong- Bekasi km. 20 Puri Niaga Blok G No. 29, Jl. Raya Rungkut Menanggal 11, Surabaya
Tel : 031-8690202 ; Fax : 031-8682123
Limusnunggal- Cileungsi Medan :
BOGOR 16820 - Indonesia Kawasan Industrial " Medan Star ", Tanjung Morawa Km.19,2
Jl. Pelita Raya Blok R No.32, Deli Serdang 20362
Tel. +62 21 8230025 Tel : 061-7941200 ; Fax : 061-7940822
Fax +62 21 8230025 Batam :
Website : www.sika.co. id Jl. Laksamana Bintan,Komp. Bumi Riau Makmur Blok E No.3,
Sungai Panas, Batam
e-mail: sikacare@id.sika.com Tel : 0778-424928 ; Fax : 0778-450189