Schedule of Rates 2018 For Amini W.E.F 01.11.2018: 1
Schedule of Rates 2018 For Amini W.E.F 01.11.2018: 1
Schedule of Rates 2018 For Amini W.E.F 01.11.2018: 1
SCHEDULE OF RATES
2018 FOR AMINI
W.E.F 01.11.2018
Sd/- Sd/-
Prepared by Checked by
Shri. K.Koyakidave Shri. Mohammed Nazeem
( Head Draughtsman ) Assiastant Engineer
( LPWD Kavaratti )
Sd/- Sd/-
Shri. M.K Abdul Salam Shri. Arun Jadhav
Executive Engineer Executive Engineer
( LPWD Kavaratti ) ( Smart Cell Kavaratti )
Sd/-
Shri.Mohammed Kudage
(Superintending Engineer)
1b1cc924da31ed689f5f2b5257dcbecc
2 1b1cc924da31ed689f5f2b5257dcbecc
Carriage of Materials
By Manual Labour including loading, unloading and
stacking for lead less than 0.5 KM
Cost per
unit
Unit cost for 1st cost
ofRates 50 metres foraddl.
50 m or
part
thereof
beyond1s
t50 m
upto 0.5
km
S. No Materials
1 Lime, mooram building 1 cum 189.01 41.15
rubbish
2 Earth 1 cum 236.26 51.44
3 Manure or sludge 1 cum 205.45 44.73
4 Excavated rock 1 cum 378.02 82.31
5 Sand, stone aggregate 1 cum 189.01 51.44
below 40 mm nominal
size
6 Stone aggregate 40 mm 1 cum 255.42 55.61
nominal size and above
7 Soling stone 1 cum 277.96 60.52
1b1cc924da31ed689f5f2b5257dcbecc
3 1b1cc924da31ed689f5f2b5257dcbecc
ANALYSIS OF RATES FOR TRANSPORTATION OF MATERILAS FROM STORE YARD TO WORK SITE AT AMINI
Vide Ref FNo.M/05/ASD/2016/850/DATED 4.10.2018
I Cement
Rate for per tonne 600.00 /Tonne
II M.sand /R.sand/local sand
Rate for per Cum (1.6 Mt/cum 800.00 800.00 Cum
III Granite Chips per Mt
Rate for per Cum ( 1.8 Mt/cum) 900.00 900.00 Cum
IV Steel
Rate for per Mt 650.00 650.00 /Tonne
V Bricks
Rate for per 1000 Nos (2.5 Mt) 1400.00 1400.00 1000Nos
Vi Timber per Mt
Rate for per Cum ( 0.8 Mt/Cum) 950.00 950.00 Cum
Vi Granite boulders
Rate for per Cum ( 2.8 Mt/cum) 1650.00 1650.00 Cum
2
ANALYSIS OF RATES FOR TRANSPORTATION OF MATERILAS FROM STORE YARD TO WORK SITE AT AMINI
SLNo Materials Total Unit
1 Cement 600.00 /Mt
2 Sand 800.00 /Cum
3 Granite chips 900.00 /Cum
4 Steel 650.00 /Mt
5 Bricks 1400.00 /1000 Nos
6 Timber 950.00 /Cum
7 Granite boulders 1650.00 Cum
1b1cc924da31ed689f5f2b5257dcbecc
4 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
5 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
6 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
7 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
8 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
9 1b1cc924da31ed689f5f2b5257dcbecc
254 Brass hard drawn hooks and eyes 200 mm 10 Nos 1037.66
255 C.P brass butt higes 100x70x4 mm 10 Nos 1080.59
256 C.P brass butt higes 75x65x4 mm 10 Nos 1624.47
257 White cement Qntl 3291.88
258 Dry distember Kg 69.42
259 Oil bound washable distemper / arcylic distemper Kg 78.72
260 Water thinnable cement primer litre 134.54
261 Water proofing cement paint Kg 68.70
262 Textured exterior paint litre 383.58
263 Exterior primer Kg 52.00
264 Arcylic exterior paint litre 307.72
265 Multi surface paint litre 551.03
266 Special primer (C.W) litre 157.44
267 Metal primer ( U.G ) litre 211.83
268 Pink primer for wood litre 138.12
269 Red oxide Zinc chromate primer litre 138.12
270 Spirit litre 84.50
271 Shellac Kg 350.66
272 Wall putty Kg 35.00
273 Black japan paint litre 160.30
274 Roofing paint for iron sheets in red colour litre 193.22
275 Oil type wood preservative litre 124.52
276 Plastic emulsion paint litre 279.09
277 Synthetic enamel paint litre 223.28
278 Aluminum paint litre 193.22
279 Acid proof paint litre 182.48
280 C.P brass chain with 32 mm dia rubber plug Each 40.79
281 C.P brass chain with 40 mm dia rubber plug Each 45.08
282 Premium Arcylic exterior paint litre 400.75
283 Superior spar varnish litre 221.84
Raj nagar Plain white marble 18 mm thick ( tablr rubbed and
284
polish) slab area up to 0.50 sqm Sqm 1123.53
Raj nagar Plain white marble 18 mm thick ( tablr rubbed and
285
polish) slab area more than 0.50 sqm Sqm 1209.41
Granite of any colour 18 mm thick ( slab area up to 0.50
286
sqm Sqm 2862.50
Granite of any colour, 18 mm thick ( slab area above 0.50
287
sqm Sqm 2934.06
288 8 mm thick marble tiles ( polished)Raj nagar Sqm 589.68
289 8 mm thick granite stone tiles ( mirror polished of all shades
Sqm 1162.18
290 Concrete Jali 50 mm thick Sqm 612.58
291 Concrete Jali 40 mm thick Sqm 422.22
292 Concrete Jali 25 mm thick Sqm 271.94
293 stand jally ( round) Each 54.39
294 Top and Bottom rail Each 357.81
295 charupadi Each 25.76
296 Precast chequered cement tiles 22 mm thick Sqm 399.50
297 Black colour dark shade pigment Kg 80.80
298 Acid and alkali resistant tiles 300x300mm Sqm 829.92
299 Acid proof cement tonne 11866.40
300 Interlocking CC paver block 60 mm thick Sqm 700.00
301 Bitumen blow type tonne 64480.00
302 Galvanized steel barbed wire Qntl 6760.00
303 Trunl buckle & straple tonne 97.94
304 Link mesh 50x50 mm made of G.I wire dia 4mm Sqm 407.4
1b1cc924da31ed689f5f2b5257dcbecc
10 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
11 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
12 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
13 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
14 1b1cc924da31ed689f5f2b5257dcbecc
SH:-2.EARTH WORK
Labour
Item No Specification Unit Rate
Rate
2.1 Surface dressing of the ground including removing vegitation
and in equalities not exceeding 15cm deep and disposal of Sqm 28.40 28.40
rubbish lead up to 50 metres and lift up to 1.5 metres
2.2 Earth work in excavation by mechanical means (Hydraulic
excavator)/ manual means over areas (exceeding 30cm in depth.
1.5m in width as well as 10 sqm on plan) including disposal of
excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to
be levelled and neatly dressed.
2.2.1 All kinds of soil Cum 445.60 445.60
2.3
Earth work in excavation/ by mechanical means (Hydraulic
Excavator)/ manual means over areas (exceeding 30 cm in depth,
1.5m in width as well as-10 sqm on plan) including disposal of
excavated earth, lead upto 50 m and lift upto 1.5 m, disposed earth to
be levelled and neatly dressed.
2.3.1 Ordinary rock Cum 628.80 628.80
2.4 Earth work in excavation by mechanical means (Hydraulic Excavator
)/ manual means in foundation trenches or drains (not exceeding 1.5
m in width or 10 sqm on plan) including dressing of sides and
ramming of bottoms, lift upto 1.5 m, including getting out the
excavated soil and disposal of surplus excavated soil as directed,
within a lead of 50 m
1b1cc924da31ed689f5f2b5257dcbecc
15 1b1cc924da31ed689f5f2b5257dcbecc
2.7.3 (b) Byond 120 cms and upto 240 cm in girth Each 9163.00
2.7.4 Felling trees of girth (measured at a hight of 1 mtr above ground
level ) including cutting of trunks and branches removing the roots
and stacking of servicable materials and disposable opf unservicable
materials ( Tree with Thorn like Muruk etc..)
2.7.4 (b) Byond 120 cms and upto 240 cm in girth Each 24265.86
2.8 Excavating trenches of required width of pipes, cables, etc including
excation for sockets and dressing of sides, ramming of bottoms,
depth upto 1.5 m including getting out the excavated soil and then
returning the soil as required in layers not exceeding 20 cm in depth,
includingconsolidating each deposited layer by ramming, watering
etc. and depositing of surplus excavated soil as directed, with in lead
od 50 m All kind of soil
1b1cc924da31ed689f5f2b5257dcbecc
16 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
17 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
18 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
19 1b1cc924da31ed689f5f2b5257dcbecc
foundation and plinth in C.M.1:6 (1Cement: 6 Metal sand) Cum 15428.82 3111.37
5.2 Brick work in super structure above plinth level upto floor five
level Cum 17050.66 3748.85
5.3 Half brick work with modular bricks of class designation in
foundation and plinth in C.M.1:4 (1Cement: 6 Metal sand) Sqm 1943.72 459.64
5.4 Half brick masonry in super structure above plinth level upto
floor five level cement mortar 1:4 ( 1 cement 4 Metal sand ) Sqm 2126.65 642.58
1b1cc924da31ed689f5f2b5257dcbecc
20 1b1cc924da31ed689f5f2b5257dcbecc
SH:-7.WOOD WORK
Labour
Item No Specification Unit Rate
Rate
7.1 Providing wood work in frames of doors, windows, clerestory
windows and other frames wrought, framed and fixed in
cum 89627.63 24996.94
position-I class Karimaruthu or equivalent ( hold fast lugs or
dasg fastener shall be paid for separately )
7.2 Providing wood work in frames of false ceiling, partitions etc.
cum 81962.53 11992.53
sawn and put up in position :
7.3 Providing and fixing 35 mm thick panelled, glazed or panelled and
glazed shutters for doors windows and clerestory windows
including anodised aluminium butt hinges with necessary screws. sqm 3516.68 1284.38
First class Karimaruthu or equivalent ( Double leef shettre)
1b1cc924da31ed689f5f2b5257dcbecc
21 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
22 1b1cc924da31ed689f5f2b5257dcbecc
7.21 Providing and fixing special quality Bright finished brass cup
board or ward robe lock with four levers of approved quality each 381.09 18.76
with necessary screws etc.. Complete.
7.22 Providing and fixing Bright finished brass door stoper with
each 124.39 3.86
rubber cusion & necessary screws .
7.23 Providing and fixing 50mm Bright finished brass cup board or
each 85.81 16.00
wardrobe knob with necessary screws .
7.24 Providing and fixing 100mm Bright finished brass mortice latch
and lock with 6 levers and a pair of lever handles with each 1607.93 19.49
necessary screws .
7.25 Providing and fixing Bright finished brass Hydraulic door
each 1941.69 99.46
closer with necessary fittings &screws .
7.26 Providing and fixing M.S Grills of required pattern in frames of
windows etc. with M.S flats squre or round bars etc. including
priming coat with approved steel primer all acomplete
7.26.1 Fixed to steel windows by welding Kg 187.53 105.56
1b1cc924da31ed689f5f2b5257dcbecc
23 1b1cc924da31ed689f5f2b5257dcbecc
SH:-7.PVC ITEMS
Labour
Item No Specification Unit Rate
Rate
7.36 Providing and fixing to existing door frames. 24 mm thick
factory made PVC door shutters made of styles and rails of a
UPVC hollow section of size 59x24 mm and wall thickness 2
mm ± 0.2 mm with inbuiltedging on both sides. The styles and
rails mitred and joined at the corners by meansof M.S.
galvanised/plastic brackets of size 75x220 mm having wall
thickness 1.0 mm and stainless steel screws. The styles of the
shutter reinforced by inserting galvanised M.S. tube of size
20x20 mm and 1 mm ± 0.1 mm wall thickness. The lock ail
made up of’H’ section, a UPVC hollow section of size 100x24 sqm 4153.04 312.34
mm and 2 mm ± r 0.2 mm wall thickness fixed to the shutter
styles by means of plastic/galvanised M.S. ‘U’ cleats. The
shutter frame filled with a UPVC multi-chambered single panel
of size not less than 620 mm, having over all thickness of 20
mm and 1 mm ± 0.1 mm wall thickness . The panels filled
vertically and tie bar at two places by inserting horizontally 6
mm galvanised M.S. rod and fastened with nuts and washers,
complete as per manufacturer’s specification and direction of
Engineer-in-charge. (For W.C. and bathroom door shutter).
7.37 Providing and fixing to existing door frames. Providing and
fixing to existing door frames. 30mm thick factory made
Polyvinyl Chloride (PVC) door shutter made of styles and rails
of a UPVC profile section of size 30mm x 60mm and wall
thickness 2mm ±0.2mm with inbuilt decorative moulding
edging on one side. The styles and rails with plastic brackets of
size 75x220mm mitre and welded at the corners. The- stiles of
the shutter reinforced by inserting galvanized M.S. tube of size
25x20mm and 1mm ± 0.1mm wall thickness. The lock rail made sqm 4402.39 312.34
up of ‘H’ section, a UPVC profile section of size 30mm x 100mm
and 2mm±0.2mm wall thickness welded to the shutter style
with a UPVC profile section single panel of size not less than
620mm, having overall thickness of 20 mm and 1 mm±0.1 mm
wall thickness with 20 mm panel beading of suitable size
/Glass(4mm thick plain glass)/louver section, louver rame of
suitable size, as per manufactures specification and direction of
Engineer-in-charge. (For W.C. and bathroom door Shutter)
1b1cc924da31ed689f5f2b5257dcbecc
24 1b1cc924da31ed689f5f2b5257dcbecc
7.38 Providing and fixing to existing door frames. 25mm thick PVC
flush door shutters upto 737mm width of colour and shade as
approved by Engineer-in-charge made out of a one piece Multi
chamber extruded PVC section of the size of 762mm X 25mm
or less as per requirement with an average wall thickness of
1mm ± 0.3mm. PVC foam end cap of size 23x10mm are
provided on both vertical edges to ensure the overall thickness
of 25mm. An MS tube having dimensions 19mm x 19mm is
sqm 4028.35 312.34
inserted along the hinge side of the door. Core of the door
shutter should be filled with High Density Polyurethane foam.
The Top & Bottom edges of the shutter are covered with an end-
cap of the size 25mm X 11mm. Door shutter shall be reinforced
with special polymeric reinforcements as per manufactures’
specification and drawing to take up necessary hardware and
fixtures. Stickers indicating the locations of hardware will be
pasted at appropriate places
7.39 Providing and fixing factory made P.V.C. door frame of size
50x47mm with a wall thickness of 5mm, made out of extruded
5mm rigid PVC foam sheet mitred at corners and joined with 2
Nos. of 150mm long brackets of 15x15mm M.S. square tube, the
vertical door profiles to be reinforced with 19x19mm M.S.
metre 698.91 55.75
square tube of 19 gauge,EPDM rubber gasket weather seal to be
provided through out the frame. The door frame to be fixed to
the wall using M.S. screws of 65/100mm size complete as per
manufacturers specification and direction of Engineer-in-
Charge.
7.40 Providing and fixing Fiber Glass Reinforced plastic (FRP)
Door Frames of cross-section 90mm x 45mm having single
rebate of 32mm x 15mm to receive shutter of 30mm thickness
.The laminate shall be molded with fire resistant grade
unsaturated polyester resin and chopped mat .Doorframe metre 748.78 58.88
laminate shall be 2mm thick and shall be filled with suitable
wooden block in all the three legs. The frame shall be covered
with fibreglass from all sides. MS stay shall be provided at the
bottom to steady the frame.
7.41 Providing and fixing to existing door frames.30 mm thick Glass
Fibre Reinforced Plastic (FRP) panelled door shutter of required
colour and approved brand and manufacture, made with fire -
retardant grade unsaturated polyester resin, moulded to 3 mm
thick FRP laminate for forming hollow rails and styles, with sqm 3824.50 329.53
wooden frame and suitable blocks of seasoned wood inside at
required places for fixing of fittings, cast monolithically with
5mm thick FRP laminate for panels confirming to TADS 6: 1993
and / or IS: 14856 - 2000 including fixing to frames.
1b1cc924da31ed689f5f2b5257dcbecc
25 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
26 1b1cc924da31ed689f5f2b5257dcbecc
Providing and fixing factory made ISI marked steel glazed doors,
windows and ventilators side /top /centre hung with beading and
all members such as F7D,F4B,KlIB and K12 B etc. complete of
standard rolled steel sections, joints mitred and flash butt welded
and sash bars tenoned and rivetted including providing and fixing
hinges pivots including priming coat of approved steel primer,but
excluding the cost of other fittings per approved design ( Sectional
weight of only steel members shall be measured for payment)
Fixing with 15x3 mm lugs 10 cmsembeded in .in cement concrete
blocks 15x10x 10cm of CC1:3:6 ( 1 cement 3 M.sand 6 stone
aggregate 20 mm nonminal size) Kg 200.50 29.40
8.11
Providing and fixing pressed steel door frames confirming to IS: 4351
manufactured from commercial mild steel sheet of 1.25 mm thickness
including hinges jamb, lock jamb, bead and if required angle
threshold of mild steel angle of section 50x25mm,or base ties of
1.60mm pressed mild steel welded or rigidly fixed together by
mechanical means, adjustable lugs with split end tail to each jamb
including steel butt hinges 2.5mm thick with mortar guards, lock
strike-plate and shock absorbers as specified and applying a coat of
approved steel primer after pre-treatment of the surface as directed
by Engineer-in-charge: Profile B Fixed with adjustable lugs with
split end tail to each jamb mtr 638.06 75.44
1b1cc924da31ed689f5f2b5257dcbecc
27 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
28 1b1cc924da31ed689f5f2b5257dcbecc
9.8 Providing and fixing 10mm thick acid and/or alkali resistant
tiles of approved make and colour using acid and/or alkali
resisting mortar bedding and joints filled with acid and/or
alkali resisting cement as per IS : 4457 complete as per the
direction of Engineer-in- Charge. In flooring on a bed of 10 mm
thick mortar 1:4(1 acid proof cement: 4 metal sand).
Acid and alkali resistant tile. Sqm 249.67 1914.17
9.9 Providing and laying vitrified tiles in floor with diffrent sizes (
thickness to be specified by the manufacture ) with water absorbtion
less than 0.08 % and confirming to IS: 15622 of approved brand and
manufacture, in all coulers and shades, laid with cement based high
polymer modifeid quick set tile adhesive ( water based ). (Khajaria
polished vitrified tiles or equivalent)
Size of tiles 500x500 mm Sqm 2753.47 581.67
9.10 Providing and laying vitrified tiles in floor with diffrent sizes (
thickness to be specified by the manufacture ) with water absorbtion
less than 0.08 % and confirming to IS: 15622 of approved brand and
manufacture, in all coulers and shades, laid with cement based high
polymer modifeid quick set tile adhesive ( water based ). (Khajaria
polished vitrified tiles or equivalent)
Size of tiles 600x600 mm Sqm 2931.02 581.67
9.11 Providing and laying vitrified tiles in floor with diffrent sizes (
thickness to be specified by the manufacture ) with water absorbtion
less than 0.08 % and confirming to IS: 15622 of approved brand and
manufacture, in all coulers and shades, laid with cement based high
polymer modifeid quick set tile adhesive ( water based ). (Khajaria
polished vitrified tiles or equivalent)
Size of tiles 800x800 mm Sqm 3079.83 581.67
9.12 Providing and laying vitrified tiles in floor with diffrent sizes (
thickness to be specified by the manufacture ) with water absorbtion
less than 0.08 % and confirming to IS: 15622 of approved brand and
manufacture, in all coulers and shades, laid with cement based high
polymer modifeid quick set tile adhesive ( water based ). (Khajaria
polished vitrified tiles or equivalent)
Size of tiles 1000x1000 mm Sqm 3208.41 581.67
9.13 Providing and laying vitrified tiles in diffrent sizes ( thickness to
be specified by the manufacture ) with water absorbtion less than
0.08 % and confirming to IS: 15622 of approved brand and
manufacture, in all coulers and shades, in skirting , riser of steps,laid
with cement based high polymer modifeid quick set tile adhesive (
water based ) (Khajaria polished vitrified tiles or equivalent)
1b1cc924da31ed689f5f2b5257dcbecc
29 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
30 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
31 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
32 1b1cc924da31ed689f5f2b5257dcbecc
9.32 Providing and laying bitumen mastic wearing course (as per
specifications) with industrial bitumen of grade 85/ 25
conforming to IS : 702, prepared by using mastic cooker and
laid to required level and slope,including providing antiskid
surface with bitumen precoated fine grained hard stone
chipping of approved size at the rate of 0.005 cum per 10 sqm
and at approximate spacing of 10 cm centre to centre in both
directions, pressed into surface protruding 1 mm to 4 mm over
mastic surface, including cleaning the surface, removal of
debris etc. all complete. ( Considering bitumen using 10.2% as
per MORTH specification).40 mm thick
Sqm 3381.55 1655.18
1b1cc924da31ed689f5f2b5257dcbecc
33 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
34 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
35 1b1cc924da31ed689f5f2b5257dcbecc
SH :-10. ROOFING
Labour
Item No Specification Unit Rate
Rate
10.1 Providing corrugated G.S. sheet roofing including vertical/curved
surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm
diameter with bitumen and G.I. limpet washers or with G.I. limpet
washers filled with white lead and including a coat of approved steel
primer and two coats of approved paint on overlapping of sheets
complete upto any pitch in horizontal/ vertical or curved surfaces)
excluding the cost of purlins, rafters and trusses and including
cutting to size and shape wherever required.
10.1.1 1.00mm thick with zinc coating not less than 275gm/m2 sqm 1692.52 206.70
10.1.2 0.80mm thick with zinc coating not less than 275gm/m 2
sqm 1441.59 206.24
10.1.3 0.63 mm thick with zinc coating not less than 275gm/sqm sqm 1227.95 205.84
10.2 Providing ridges or hips of width 60 cm over all width plain
G.S. sheet fixed with polymer coated J. or L hooks, bolts and
nuts 8 mm dia. G.I. limpet and bitumen washers complete.
10.2.1 0.80mm thick with zinc coating not less than 275gm/m2 sqm 1049.14 452.61
10.2.2 0.63mm thick with zinc coating not less than 275gm/m2 metre 939.56 452.40
10.3 Providing and laying pressed clay tiles (as per approved pattern 20
mm nominal thickness and of approved size) on roofs jointed with
cement mortar 1:4 (1 cement:4 coarse sand) mixed with 2% integral sqm 996.38 306.53
water proofing compound laid over a bed of 20 mm thick cement
mortar 1:4(1 cement: 4 coarse sand) and finished neat complete.
10.4 Providing and fixing insulating board ceiling of approved quality
1b1cc924da31ed689f5f2b5257dcbecc
36 1b1cc924da31ed689f5f2b5257dcbecc
10.6 Providing and fixing at all height false ceiling including providing
and fixing of frame work made of special sections power pressed
from M.S. sheet and galvanised in accordance with zinc coating of
grade 350 as per IS : 277 and consisting of angle cleats of size 25mm
wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm
centre to centre one flange fixed to the ceiling with dash fastener
12.5mm diax40mm long with 6mm dia bolts to the angle hangers of
clips made out of 2.64mm diax230mm long G.I. wire at every
junction including fixing the gypsum board with ceiling section and
perimeter channels 0.5mm thick 27mm high having flanges of 20mm
and 30mm long, the perimeter of ceiling fixed to wall/partition with
the help of rawl plugs at 450mm centre to centre with 25mm long
drive-all screws @ 230mm interval including jointing and fixing to a
flush finish of tapered and square edges of the board with
recommended filler,jointing tapes, finisher and two coats of primer
suitable for board as per manufactures specification and also
including the cost of making openings for light fittings, grills,
diffusers, cutouts made with frame of perimeter channels suitably
fixed all complete as per drawing and specification and direction of
the Engineer -in-charge but excluding the cost of painting with:
10.6.1 12.5 mm thick tapered edge gypsum board conforming to IS: 2095-
sqm 1584.51 682.34
Part I,
10.6.2 12.5 mm thick tapered edge gypsum fire resistant board conforming
to IS: 2095- Part I, sqm 1722.84 682.34
10.6.3 12.5 mm thick tapered edge gypsum moisture resistant board sqm 1803.92 682.34
10.7 Providing & fixing on roof pressed clay tile (Mangalor tile of 20 mm
nominal thickness and of approved size and as per approved pattern sqm 532.15 174.78
10.8 Providing & laying on roof pressed clay tile ridge (Mangalore tile) of
20mm thickness and of approved pattern on steel frame work
complete (sfeel frame work to be paid separately) sqm 233.47 41.48
10.9 Providing and fixing on wall face unplasticised Rigid PVC rain water
pipes conforming to IS : 13592 Type A including jointing with seal
metre 227.88 112.87
ring conforming to IS :5382 leaving 10 mm gap for thermal
expansion, (i) Single socketed pipes 75 mm dia
10.10 Providing and fixing on wall face unplasticised Rigid PVC rain water
pipes conforming to IS : 13592 Type A including jointing with seal
metre 349.51 137.93
ring conforming to IS :5382 leaving 10 mm gap for thermal
expansion, (i) Single socketed pipes 110 mm dia
10.11
Providing Aluminium sheet roofing fixed with .galvnized iron Jor L
Sqm. 1379.35 80.75
hooks and 8mm dia C.I plain bitumen washers complete excluding
the cost of purlins, rafters and trusses corrugated sheet 0.56mm thick.
1b1cc924da31ed689f5f2b5257dcbecc
37 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
38 1b1cc924da31ed689f5f2b5257dcbecc
SH:- PAINTING
11.18 Applying one coat of water thinnable cement primer of approved
brand and manufacture on wall surface.Water thinnable cement Sqm 77.88 65.50
primer
11.19 Distempering with oil bound washable distemper of approved brand
and manufacture to give an even shade.New work ( two or more
Sqm 192.27 163.83
coats) over and including priming coat with water thinnable cement
primer
11.20 Distempering with 1st quality arcylic washable distemper ( ready
mixed )of approved brand and manufacture of required shade and
Sqm 105.08 11.61
colour complete as per manufactures specification.Two or more coats
on new work.
11.21 Finishing wall with water proofing cement paint of approved brand
and manufacture of required shade on new work (two or more coats Sqm 116.19 85.55
applied @3.84Kg/10 sqm)
11.22 Finishing wall with texture exterior paint of required shade on new
work (two or more coats applied @3.28ltr/10 sqm) over including Sqm 262.94 102.11
on new work (two or more coats applied @1.67ltr/10 sqm) over Sqm 176.53 102.11
1b1cc924da31ed689f5f2b5257dcbecc
39 1b1cc924da31ed689f5f2b5257dcbecc
11.27 Applying priming coat with ready mixed pink or grey primer of
approved brand and manufacture on wood work ( hard and soft Sqm 66.73 53.06
wood )
11.28 Applying priming coat with ready mixed red oxide zinc chromate
primer of approved brand and manufacture on steel galvanised iron Sqm 59.72 48.89
/steel works
11.29 Finishing with with Epoxy paint (two or more coats) at all locations
prepred and applied as per manufacture's specifications including
Sqm 268.85 160.72
appropriate priming coat ,preperations of surface,etc.. complete on
steel works.
11.30 French spirit polishing f on a new work ( two or more coats )
including a coat of wood filler with ready mixed polish of approved Sqm 442.12 408.69
brand and manufacture.
11.31 Providing and applying white cement based of average thickness
1mm of approved brand and manufacture, over plastered surface to Sqm 156.95 97.68
11.33 Providing and applying plaster of paris putty of 2mm thickness over
plastered surface to prepare the surface even and smooth complete. Sqm 237.42 197.34
(Birla White or equivalent).
11.34 Providing and applying wall putty of 2mm thickness over plastered
surface to prepare the surface even and smooth complete. (Nerolac Sqm 290.84 197.34
or equivalent).
11.35 Painting Wood work with Deluxe Multi surface paintto give an
even shade.Two or more coats applied on @0.90ltr/10 sqm) over
Sqm 198.77 102.11
under coat of primer applied @ 0.75 ltr/10 sqm of approved and
manufacture (Berger/Birla or equivalent)
11.36 Finishing with Deluxe Multi surface paint system for interiors and
exteriors using primer as per manufactures specifications two or
more coats applied with Teflon coated Royal coated) on walls Sqm 210.72 0.00
@1.25ltr/10 sqm) over including priming coat of special primer
applied @ 0.75 ltr/10 sqm. (Asian Paint or equivalent)
11.37 Finishing wall with Arcylic smooth exterior paint of required shade
on new work (two or more coats applied @1.67ltr/10 sqm) over
Sqm 154.41 102.11
including priming coat of exterior primer applied @ 2.20 kg/10 sqm.
(Nerolac paint premier or equivalent). Exterior
11.38 Wall painting with acrylic emulsion paint, having VOC
(Volatile Organic Compound ) content less than 50 grams/ litre,
of approved brand and manufacture, including applying Sqm 156.28 111.41
additional coats wherever required, to achieve even shade and
colour.Two coat
11.39 Applying one coat of white cement of approved brand and
manufacture on wall surface. Sqm 45.03 32.67
1b1cc924da31ed689f5f2b5257dcbecc
40 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
41 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
42 1b1cc924da31ed689f5f2b5257dcbecc
finishing with matching surface after housing G.I. pipe etc Metre 198.24 155.22
12.22.1 Providing and fixing ball valve ( PVC ) of approved quality and
manufacture complete.63 mm nominal bore Each 394.78 32.40
12.22.2 Providing and fixing ball valve ( PVC ) of approved quality and
manufacture complete.50 mm nominal bore Each 364.29 29.79
12.22.3 Providing and fixing ball valve ( PVC ) of approved quality and
manufacture complete.32 mm nominal bore Each 309.08 24.52
12.22.4 Providing and fixing ball valve ( PVC ) of approved quality and
manufacture complete.25 mm nominal bore Each 248.18 21.69
12.23.1 Providing and fixing PTMT grating of approved quality and
colour.Circular type.
100 mm nominal dia. Each 89.66 8.36
12.23.2 Providing and fixing PTMT grating of approved quality and
colour.Circular type.
125 mm nominal dia with 25 mm waste hole. Each 105.93 8.36
12.23.4 Providing and fixing PTMT grating of approved quality and
colour.Rectangular type with openable circular lid.
1b1cc924da31ed689f5f2b5257dcbecc
43 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
44 1b1cc924da31ed689f5f2b5257dcbecc
SH:13.SANITORY
Labour
Item No Specification Unit Rate
Rate
13 Providing anf fixing white vitrous China water closet Pedestal pan
(European) type WC pans with white plastic seat and lid and rubber
buffers, 15 white vitrous China low level flushing system of
approved make with fittings and brackets 40mm flush bend, 20mm
over flow pipe with complete including cutting and making good the
walls and floors where required.
13.1 White EWC pan with plastic seat and lid Each 6574.96 2928.79
13.2 Providing anf fixing white vitrous China wash basin with RS or CI
brackets painted white, 15mm C.P bras pillar tap and C.P brass chain
and rubber plug 32mm C,P. brass waste of standrad pattern 32mm
diametre and waste pipe complete including cutting and making
good the walls and floors where required.
13.2.1 White vitreous China Flat back wash basin 550x400mm with one
Each 3065.81 1288.55
15mm C.P. brass pillar tap.
13.3 Providing anf fixing white vitrous China kitchen sink with CI
brackets painted white, 15mm C.P bras pillar tap and C.P brass chain
and rubber plug 40mm brass waste of standrad pattern 40mm
diametre and waste pipe complete including cutting and making
good the walls and floors where required.
13.3.1 White gazed fire clay kitchen sink size 600x450x250mm Each 4437.33 1134.66
13.4 Providing anf fixing Stailess steel A ISI 304 ( 18/8) kitchen sink asper
IS 13983 with CI brackets stainless steel plug 40 mm ,including
painting of fittings and brackets, cutting and making good the walls
where required.
13.4.1 Kitchen sink with drain board 510x1040 mm bowl deth 250 mm
Each 10737.79 1659.07
13.5 Providing anf fixing white vitrous China laboratory sink with CI
brackets painted white, 15mm C.P bras pillar tap and C.P brass chain
and rubber plug 40mm brass waste of standrad pattern 40mm
diametre and waste pipe complete including cutting and making
good the walls where required.
Sink size 450x300x150mm Each 3794.39 1134.66
13.6 Providing anf fixing 600x450mm mirror of superior glass (approved
quality) complete with 6mm thick asbestose sheet ground fixed to Each 1441.08 624.51
1b1cc924da31ed689f5f2b5257dcbecc
45 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
46 1b1cc924da31ed689f5f2b5257dcbecc
13.13.4 Providing and fixing white vitreous china flat back or wall
corner type lipped front urinal basin of 430x260x350mm and
340x410x265mm sizes respectively with automatic flushing
cistern with standard flush pipe and C.P. brass spreaders with
Each 17177.31 10387.42
brass unions and G.I clamps complete, including painting of
fittings and brackets,cutting and making good the walls and
floors wherever required :Range of four urinal basins with 10
litre white P.V.C. automatic flushing cistern.
13.14 Providing and fixing trap of self cleansing design with screwed
down or hinged grating with or without vent arm complete,
including cost of cutting and making good the walls and floors: Each 1677.34 992.76
100 mm inlet and 100 mm outlet Sand cast iron S&S as per IS:
3989.
13.15 Providing and fixing white vitrous China water closet Pedestal
pan (European) type WC pans with white plastic seat and lid
and rubber buffers, 15 white vitrous China low level flushing
system of approved make with fittings and brackets 40mm
flush bend, 20mm over flow pipe with complete including
cutting and making good the walls and floors where required.
(Jaquar model No SLS-WHT-0311/SLS-WHT-0318 or
Equivalent)
White EWC pan with plastic seat and lid each 15795.34 2928.79
13.16 Providing and fixing white vitrous China wash basin with RS
or CI brackets painted white, 15mm C.P bras pillar tap and C.P
brass chain and rubber plug 32mm C,P. brass waste of standrad
pattern 32mm diametre and waste pipe complete including
cutting and making good the walls and floors where required
White vitrous china wash basin 550x605x475mm with half
Each 11788.59 1288.55
pedastal (Jaquar modal FNS WHT - 1503 or equivalent)
13.17 Providing and fixing mirror of superior glass (approved
quality) complete with 6mm thick asbestose sheet ground fixed
Each 1810.11 624.51
to wooden cleats with necessary screws and washers. ( Cera
model No 5561 size 700x500mm )
13.18 Providing and fixing P.V.C low level flushing cistern with
manually controlled device ( handle lever) confirming to IS Each 1685.88 264.53
:7231 with all fittings and fixtures complete.
13.19 Providing anf fixing Stailess steel A ISI 304 labour room sink
including fitting and brackets,cutting and making good the Each 52350.81 1659.07
walls where required.
13.20 Providing anf fixing Stailess steel A ISI 304 ( 18/8) kitchen sink
asper IS 13983 with CI brackets stainless steel plug 40 mm
,including painting of fittings and brackets, cutting and making Each 3242.18 1659.07
good the walls where required. With out drain board
450x400x250 mm
13.21 Providing and fixing 100 mm PVC grating for gully trap. Each 60.90 8.60
13.22 Providing and fixing in position 25mm diameter mosquito
Each 73.45 3.75
proof coupling of approved municipal design.
13.23 Providing and fixing 600x120x5mm glass shelf with edges
round of supported on anodised aluminium angle frame with
Each 984.10 472.96
C.P. brass brackets and guard rail complete fixed with 40 mm
long screws, rawl plugs etc., complete.
1b1cc924da31ed689f5f2b5257dcbecc
47 1b1cc924da31ed689f5f2b5257dcbecc
13.24 Providing and fixing toilet paper holder : C.P. brass Each 678.60 231.90
13.25 Providing and fixing toilet paper holder: Vitreous china Each 599.80 231.90
SH:-14. DRAINAGE
Labour
Item No Specification Unit Rate
Rate
14.1 Providing,laying and P.V.C pipes grade "A" with stiff mixture
of 1:3 (1 cemenr 3 metal sand) including testing of joints etc.
complete.
14.1.1 110mm diametre Metre 561.96 186.01
14.1.2 90mm diametre Metre 516.02 186.01
14.1.2 75 mm diametre Metre 467.51 186.01
14.1.2 63 mm diametre Metre 424.83 186.01
14.2.1 Providing and laying cement concrete 1:5:10 (1 cement : 5 metal
sand : 10 graded stone aggregate 40 mm nominal size) upto
Metre 933.20 241.62
haunches of pipes including bed concrete as per standard
design .100mm dia pipe
14.2.2 Providing and laying cement concrete 1:5:10 (1 cement : 5 metal
sand : 10 graded stone aggregate 40 mm nominal size) upto
Metre 1512.44 391.60
haunches of pipes including bed concrete as per standard
design : 150 mm diameter pipe
14.3 Dislodging of septic tank including disposal of sludge by
digging a pit within a lead of 50 meters and covering it with
sand including adding disinfectants etc..including washing the
tank and re-arranging of soak pit ,manhole etc..complete as
directed by the Engineer-in-charge. cum 1627.69 0
1b1cc924da31ed689f5f2b5257dcbecc
48 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
49 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
50 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
51 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
52 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
53 1b1cc924da31ed689f5f2b5257dcbecc
SH:-18.REPAIRS TO BUILDINGS
Labour
Item No Specification Unit Rate
Rate
18.1 Repairs to plaster of thickness 12mm to 20mm in patches of
area 2.5 sq. metres and under including cutting the patch in
proper shape, raking out joints and preparing and plastering
sqm 584.05 419.65
the surface of the walls complete including disposal of rubbish
to the dumping ground within 50 metres lead :Cement mortar
1:4
18.2 Fixing chowkhats in existing opening including embedding
chowkhats in floors or walls cutting masonry for holdfasts
embedding hold fasts in cement concrete blocks with cement
concrete 1:3:6 (1 cement : 3 metal sand : 6 graded stone
aggregate 20 mm nominal size) painting two coats of approved each 1722.26 1240.82
wood preservative to sides of chowkhats and making good the
damages to walls and floors as required complete including
disposal of rubbish to the dumping ground within 50 metres
lead :
18.3.1 Renewing glass panes and refixing existing wooden fillets:
and the like by scrapping, sand papering and preparing the surface sqm 19.91 19.91
1b1cc924da31ed689f5f2b5257dcbecc
54 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
55 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
56 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
57 1b1cc924da31ed689f5f2b5257dcbecc
19.11 Dismantling steel work in built up sections in angles, tees, flats and
channels including all gusset plates, bolts, nuts, cutting rivets,
Kg 4.61 4.61
welding etc. including dismembering and stacking within 50metres
lead.
19.12 Dismantling tile work in floors and roofs laid in cement mortar
including stacking material within 50 metre lead.For thickness of Sqm 61.53 61.53
tiles above 10 mm and upto 25 mm
19.13 Demolishing brick tile covering in terracing including stacking
of serviceable material and disposal of unserviceable material Sqm 88.65 88.65
within 50 metres lead.
19.14.1 Dismantling roofing including ridges, hips valleys and gutters
1b1cc924da31ed689f5f2b5257dcbecc
58 1b1cc924da31ed689f5f2b5257dcbecc
19.26 Dismantling C.I. or asbestos rain water pipe with fittings and
1b1cc924da31ed689f5f2b5257dcbecc
59 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
60 1b1cc924da31ed689f5f2b5257dcbecc
20.4 Extra for fixing marble /granite stone over and above
corresponding basic item, in facia and drops of width upto 150
Metre 490.65 402.16
mm with epoxy resin based adhesive including cleaning etc.
complete.
20.5 Extra for providing opening of required size & shape for wash
basins/ kitchen sink in kitchen platform, vanity counters and
similar location in marble/Granite/stone work including Each 2865.32 820.56
necessary holes for pillar taps etc. including rubbing and
polishing of cut edges etc. complete.
20.6 Mirror polishing on marble work/Granite work/stone work
sqm 402.16 348.45
where ever required to give high gloss finish complete.
20.7 Stone tile (polished) work for wall lining over 12mm thick bed
of cement mortar 1:3 (1 cement: 3metal sand) and cement slurry
@ 3.3 kg/sqm including pointing in white cement complete.
20.7.1 8 mm thick.
Raj Nagar plain white marble/ Udaipur green marble/ Zebra
sqm 3008.46 2048.27
black marble.
20.7.2 8mm thick.Granite of any colour and shade. sqm 3687.39 2048.27
1b1cc924da31ed689f5f2b5257dcbecc
61 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc
62 1b1cc924da31ed689f5f2b5257dcbecc
1b1cc924da31ed689f5f2b5257dcbecc