LG DATA Service Usb Install v2

CDMA Fixed W ir eless Phone
Data Kit Manual

LGE CDMA Fixed Wireless Telephone
Data Kit Manual
3
Data Kit Manual
REVISED HISTORY
DATE ISSUE CONTENTS OF CHANGES S/W VERSION
2004/08 ISSUE 1 Initial Release
4
Data Kit Manual
Blank Page
5
Data Kit Manual
Table of Contents
1 Introduction-------------------------------------------------------------------------------------------------------------7
2 Components-------------------------------------------------------------------------------------------------------------7
3 Installation--------------------------------------------------------------------------------------------------------------8
3.1 Installation USB CDMA modem driver-----------------------------------------------------------------------8
4 Usage of Various Data Services (Windows 98)-----------------------------------------------------------------12
4.1 BBS service or ‘1 to 1 connection’ with a common communication emulator such as hyper
terminal---------------------------------------------------------------------------------------------------------12
4.1.1 Set up Program-------------------------------------------------------------------------------------------12
4.1.2 Configuration---------------------------------------------------------------------------------------------13
4.1.3 Usage------------------------------------------------------------------------------------------------------14
4.2 Packet Service -------------------------------------------------------------------------------------------------15
4.2.1 Manually operated Setting------------------------------------------------------------------------------15
4.2.1.1 Configuration a connection environment for the Internet service --------------------------15
4.2.1.2 Dialing and getting an Internet service started-------------------------------------------------17
4.3 FAX Service------------------------------------------------------------------------------------------------------18
4.3.1 Sending FAX---------------------------------------------------------------------------------------------18
4.3.2 Receiving FAX-------------------------------------------------------------------------------------------18
5 Usage of Various Data Services ( Windows 2000 and XP )--------------------------------------------------19
5.1 BBS service or ‘1 to 1 connection’ with a common communication emulator such as hyper
terminal --------------------------------------------------------------------------------------------------------19
5.1.1 Set up Program-------------------------------------------------------------------------------------------19
5.1.2 Configuration---------------------------------------------------------------------------------------------20
5.1.3 Usage------------------------------------------------------------------------------------------------------21
5.2 Packet Service -------------------------------------------------------------------------------------------------22
5.2.1 Manually operated Setting------------------------------------------------------------------------------22
5.2.1.1 Configuration a connection environment for the internet service --------------------------22
5.2.1.2 Dialing and getting an Internet service started-------------------------------------------------23
5.3 FAX Service------------------------------------------------------------------------------------------------------28
5.3.1 Sending FAX---------------------------------------------------------------------------------------------28
5.3.2 Receiving FAX-------------------------------------------------------------------------------------------28
6
Data Kit Manual
1 Introduction
LGE WLL Data Service enables wireless data communications through the WLL phone.
By simply attaching the handset to any desktop PC, the user can perform circuit or
packet data services including various tasks such as data transmission, Internet
browsing, and facsimile transmission.
2 Components
 A USB cable or Serial Cable
 A CD_ROM containing a LG USB Modem Driver.
(If you use Serial Cable, USB driver is not needed)
 Please make sure that these components are present before you begin the
service. If any missing or damage of components is found, contact our authorized
LGE distributor immediately.
 This software is developed for the MS Windows 98, 2000, XP
7
Data Kit Manual
3 Installation
3.1 Installation USB CDMA modem driver
 Installation a USB CDMA modem is needed before doing manually operated
setting (4.2.1)
a. Make sure that the WLL phone and PC are both turned on
b. Install USB Driver using included CD_ROM. Insert CD_ROM into CD_ROM Driver.
And Run ‘LGUSBModemDriver.exe’. Provide ‘LGUsbModemDriver_InstallGuide’ in
CD_ROM.
c. Set data port to USB on WLL phone.
1). Select “Menu” (On soft menu)
2). Select “6. Settings”
3). Select “3. Phone”
4). Select “2. Data Settings”
5). Select “2. Data Baud”
6). Select “1. USB”
d. Connect the USB cable first to the WLL Phone’s USB port, then to an available PC’s
USB port
e. This message window will appear, informing you that new hardware has been found
f. Click ‘next’
8
Data Kit Manual
g. Select "Search for the best driver for your device. [Recommended]", and click ‘Next’.
h. Check off “Specify a location:”
Use the ‘Browse’ to select the folder where USB driver files exist
i. Select the “lgusbmodem.INF” item in that folder. Click ‘next’
9
Data Kit Manual
j. If a message, "Windows has finished installing ….”, is displayed, Click ‘Finish’.
k. Once this driver is installed, the PC should automatically sense the new device and
start the second Plug and Play installation for the specific USB CDMA modem.
l. Select "Search for the best driver for your device.[Recommended]", and click ‘Next’.
10
Data Kit Manual
m. Check off “Specify a location:” use the ‘Browse’ to select the folder where USB driver
files exist
n. Select the “lgusbmodem.INF” item in that folder, Click next
o. Click ‘Finish’
11
Data Kit Manual
4 Usage of Various Data Services (Windows 98)

LGE WLL Data Service support circuit data services, such as BBS service, fax service,
and Internet service by using a circuit connection, and packet data service such as
Internet service by using a packet connection.
4.1 BBS service or ‘1 to 1 connection’ with a common communication

emulator such as hyper terminal
4.1.1 Set up Program
In case of using Hyper terminal as communication emulator.
a. Select Hyper terminal.
Start => Accessories => Communications => Hyper Terminal
b. Execute Hypertrm.
c.Enter the connection name and choose icon.
d. Enter the connection phone number and click “OK”
12
Data Kit Manual
Be careful about “Connect using” field, Select proper device you using.
4.1.2 Configuration
a. Select a communication port where LG USB MODEM is installed: If you get "OK"
message after commanding "AT" in the terminal, you've done right selection.
b. Setup port configuration like below.
- Baud rate: don’t care
- Data bits: 8
- Parity: None
- Stop bits: 1
- Flow control: Hardware flow control
13
Data Kit Manual
c. Set data port to USB on WLL phone.
4.1.3 Usage
a. Called party (in the ‘1 to 1 connection’) :
- Change mode to a receiving mode for the data service by commanding
“AT$LDR=1”.
- If you want manual answer, command “ATA” to answer for a ring.
- Otherwise, set auto answering ring count N by commanding “ATS0=N”
- Just wait for dozens of seconds until a message, “CONNECT”, is displayed.
b. Calling party :
- Connect to a BBS system or your partner by commanding “ATDT

phone_number”.
c. To end a call :
- Hook off or
- Return to a command mode by typing “+++”, and command “ATH” after a

message, ”OK”.
14
Data Kit Manual
4.2 Packet Service

4.2.1 Manually operated Setting
4.2.1.1 Configuration a connection environment for the Internet service
a. Select ‘Start -> Program -> Accessories -> Communications -> Dial-Up Networking
-> Make New Connection’
b. Input a name for the computer you are dialing, select the modem, “LG CDMA USB
Modem[VCOMM]”, installed above, and press ‘Configure…’.
15
Data Kit Manual
c. Select the port connected to WLL phone as a communications port.
The phone is connected to the USB bus. Independent of Maximum speed value, it can
hit the 12Mbps shared by all other devices. This Maximum speed item doesn’t have
any effect on communication between the Phone and PC. So you don’t have to
specify the Maximum speed.
d. Select ‘Connection’, and setup ‘Connection preferences’ like the right figure. Then,
press ‘Advanced’.
16
Data Kit Manual
e. Input commands (for example, AT+CRM, AT$LGPKT, AT$LGQNC), that inform the
WLL phone of the interface protocol that will be used. And press ‘OK’.
You need to combine commands for high speed packet data service.
at+crm=1;$lgpkt=3
4.2.1.2 Dialing and getting an Internet service started

a. Open the new connection made above. After filling in a user id, password and the
phone number of the service provider (some of those service providers don’t care the
phone number), press ‘Connect’.
17
Data Kit Manual
4.3 FAX Service

For PC FAX Service, You should purchase a commercial PC FAX Program and use H/W
Flow control.
4.3.1 Sending FAX

When setting up a PC FAX Application, you should choose a modem as LG USB CDMA
Modem.
4.3.2 Receiving FAX

To receive Fax, You Should Change mode to receiving mode for the FAX service
18
Data Kit Manual
5 Usage of Various Data Services ( Windows 2000 and XP )

LGE WLL Data Service support circuit data services, such as BBS service, fax service,
and Internet service by using a circuit connection, and packet data service such as
internet service by using a packet connection.
5.1 BBS service or ‘1 to 1 connection’ with a common communication

emulator such as hyper terminal
5.1.1 Set up Program
In case of using Hyper terminal as communication emulator.
e. Execute Hyper terminal.
Start => Accessories => Communications => Hyper Terminal
f. Fill the location information.
19
Data Kit Manual
g. Enter the connection name and choose icon.
h. Enter the connection phone number and click “OK”

Be careful about “Connect using” field, Select proper device you using.
5.1.2 Configuration
a. Select a communication port where LG CDMA USB MODEM is installed: If you get
"OK" message after commanding "AT" in the terminal, you've done right selection.
20
Data Kit Manual
b. Setup port configuration like below.
- Baud rate : don’t care
- Data bits : 8
- Parity : None
- Stop bits : 1
- Flow control : Hardware flow control
5.1.3 Usage
a. Called party (in the ‘1 to 1 connection’) :
- Change mode to a receiving mode for the data service by commanding

“AT$LDR=1”.
- If you want manual answer, command “ATA” to answer for a ring.
- Otherwise, set auto answering ring count N by commanding “ATS0=N”
b. Calling party:
- Connect to a BBS system or your partner by commanding “ATDT phone_number”.
c. To end a call:
- Hook off or
- Return to a command mode by typing “+++”, and command “ATH” after a

message, ”OK”.
21
Data Kit Manual
5.2 Packet Service

5.2.1 Manually operated Setting
5.2.1.1 Configuration a connection environment for the internet service
a. Select ‘Start -> Setting -> Control Panel -> Phone and Modem options’
b. Input a name for the computer you are dialing, select the modem, “LGE CDMA USB
Modem”, installed above, and press ‘Properties…’.
c. Select the port connected to WLL phone as a communications port.
22
Data Kit Manual
The phone is connected to the USB bus. Independent of Maximum speed value it can hit
the 12Mbps shared by all other devices. This Maximum speed item doesn’t have any
effect on communication between the Phone and PC. So you don’t have to specify the
Maximum speed.
d. Select ‘Connection Port Speed ’, and press ‘Advanced’. Input commands (for
example, AT+CRM, $LGPKT, AT$LGQNC) that inform the WLL phone of the interface
protocol that will be used. And press ‘OK’. You need to combine commands for high
speed packet data service.
at+crm=1;$lgpkt=3
5.2.1.2 Dialing and getting an Internet service started

a. Open the new connection made above.
23
Data Kit Manual
Select ‘Start -> Programs -> Accessories -> Communications -> Network and Dial-up
Connections’. And ‘Make New Connection’ Double Click
b. Select Network Connection Type.
c. After filling in the phone number of the service provider (some of those service
providers don’t care the phone number), press ‘Next’.
24
Data Kit Manual
d. You are input to special name for this connection (Ex. WLL Modem Telecomm), and
Press Finish.
e. Finally, You are input in a user name, password and the dial number of the service
provider. And press ‘Dial’
25
Data Kit Manual
f. Check your username and password in service provider system.
g. If you are Member in service provider, connected in Packet Data Service.
And Start in Internet Service or Packet Service.
26
Data Kit Manual
h. Repeatedly, if you want connect in Data Service, Double click ‘Dial-up Connection’
(you made special name above)
27
Data Kit Manual
5.3 FAX Service

For PC FAX Service, You should purchase a commercial PC FAX Program and use H/W
Flow control.
5.3.1 Sending FAX

When setting up a PC FAX Application, you should choose a modem as LG USB CDMA
Modem.
5.3.2 Receiving FAX

To receive Fax, You should change mode to receiving mode for the FAX service on WLL
phone.
28

LG DATA Service Usb Install v2

Uploaded by

Copyright:

Available Formats

LG DATA Service Usb Install v2

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

LG DATA Service Usb Install v2

Uploaded by

Copyright:

Available Formats

CDMA Fixed W ir eless Phone

Data Kit Manual

3.1 Installation USB CDMA modem driver-----------------------------------------------------------------------8

4 Usage of Various Data Services (Windows 98)-----------------------------------------------------------------12

5 Usage of Various Data Services ( Windows 2000 and XP )--------------------------------------------------19

 A CD_ROM containing a LG USB Modem Driver.

(If you use Serial Cable, USB driver is not needed)

 This software is developed for the MS Windows 98, 2000, XP

c. Set data port to USB on WLL phone.

1). Select “Menu” (On soft menu)

2). Select “6. Settings”

3). Select “3. Phone”

4). Select “2. Data Settings”

5). Select “2. Data Baud”

6). Select “1. USB”

h. Check off “Specify a location:”

i. Select the “lgusbmodem.INF” item in that folder. Click ‘next’

j. If a message, "Windows has finished installing ….”, is displayed, Click ‘Finish’.

n. Select the “lgusbmodem.INF” item in that folder, Click next

4 Usage of Various Data Services (Windows 98)

4.1 BBS service or ‘1 to 1 connection’ with a common communication

a. Select Hyper terminal.

Start => Accessories => Communications => Hyper Terminal

c.Enter the connection name and choose icon.

d. Enter the connection phone number and click “OK”

b. Setup port configuration like below.

- Baud rate: don’t care

- Flow control: Hardware flow control

c. Set data port to USB on WLL phone.

- Change mode to a receiving mode for the data service by commanding

- If you want manual answer, command “ATA” to answer for a ring.

- Otherwise, set auto answering ring count N by commanding “ATS0=N”

- Just wait for dozens of seconds until a message, “CONNECT”, is displayed.

- Connect to a BBS system or your partner by commanding “ATDT

- Just wait for dozens of seconds until a message, “CONNECT”, is displayed.

- Return to a command mode by typing “+++”, and command “ATH” after a

4.2 Packet Service

c. Select the port connected to WLL phone as a communications port.

4.2.1.2 Dialing and getting an Internet service started

4.3 FAX Service

4.3.1 Sending FAX

4.3.2 Receiving FAX

5 Usage of Various Data Services ( Windows 2000 and XP )

5.1 BBS service or ‘1 to 1 connection’ with a common communication

e. Execute Hyper terminal.

Start => Accessories => Communications => Hyper Terminal

f. Fill the location information.

g. Enter the connection name and choose icon.

h. Enter the connection phone number and click “OK”

b. Setup port configuration like below.

- Baud rate : don’t care

- Flow control : Hardware flow control

- Change mode to a receiving mode for the data service by commanding

- If you want manual answer, command “ATA” to answer for a ring.

- Otherwise, set auto answering ring count N by commanding “ATS0=N”

- Just wait for dozens of seconds until a message, “CONNECT”, is displayed.

- Connect to a BBS system or your partner by commanding “ATDT phone_number”.

- Just wait for dozens of seconds until a message, “CONNECT”, is displayed.

- Return to a command mode by typing “+++”, and command “ATH” after a

5.2 Packet Service