JM - ETACS

ETACS

1 Chonan Technical Service Training Center

JM - ETACS

CONTENTS

2 Chonan Technical Service Training Center

JM - ETACS

ETACS
1. General
ETACS was applied for body electrical system control with existent vehicles even if gouge JM
Function that control is controlled to approach with a different car
Also, develop into Anti theft function to do control according to specification in ETACS.

1.1 Electric performance

Item Requirement Remarks

Rated voltage DC 12V

Rang of operating voltage DC 9 ~ 16V .
Rang of operating temp. -30
~ +80

Conservation range of
-40
~ +85

temperature
Use maximum humidity 95%
IGN1: OFF & IGN2:OFF &
All electrical load OFF &
30seconds passes after Tx
Less than 4mA signal reception &
Parasite electric current
(ETACS & Anti theft controller) 4seconds passes after door
(Dark electric current)
Less than 3mA(ETACS controller) key unlock S/W from OFF to
ON &
2seconds passes under
the no change of input switch

J M E TA C

3 Chonan Technical Service Training Center

JM - ETACS

1.2 Rated load

Item Load

Room lamp Dc 12v 12w(lamp load)

IGN. key illumination lamp Dc 12v 2w(lamp load)
Seat belt indicator Dc 12v(led load)
Tail lamp relay / DRL Dc 12v 200ma(induced load)
Rear fog relay Dc 12v 200ma(induced load)
Door lock relay Dc 12v 200ma(induced load)
Door unlock relay Dc 12v 200ma(induced load)
Door unlock relay DC 12V 200ma(Induced load)
Hazard relay Dc 12v 200ma(induced load)
Start inhibit relay Dc 12v 200ma(induced load)
Burglar horn Dc 12v 200ma(induced load)
Power window relay Dc 12v 200ma(induced load)
Wiper relay Dc 12v 200ma(induced load)
Rear defogger relay Dc 12v 200ma(induced load)
Front deicer relay Dc 12v 200ma(induced load)
Chime bell Dc 12v 350ma(induced load)

4 Chonan Technical Service Training Center

JM - ETACS

1.3 Input signal characteristic

Recognition
No Input signal Condition Remarks
ON/OFF voltage level

1 BAT ON=BAT 9~16volts BAT=Battery

ON: Higher than7volts

2 IGN1 ON = BAT with IGN. KEY ON
Off: Lower than 4volts
ON: Higher than7volts
3 IGN2 ON = BAT with IGN. KEY ON)
Off: Lower than 4volts
ENG ON: Higher than7volts
4 ALT “L” ON = Charging volt with ENG ON
ENG Off: Lower than 4volts
Insert: Higher than7volts
5 Ignition Key Switch Insert = BAT (KEY insert)
Removed: Lower than 4volts
6 Driver DR S/W Open = GND Lower than 1 volt/Open ON: DR Open
7 Assist DR S/W Open = GND Lower than 1 volt/Open ON: DR Open
Door Open = GND
8 4 Door S/W Lower than 1 volt/Open ON:DR Open
All DR Closed = Open
Driver DR
9 Lock = Open, Unlock = GND Lower than 1 volt/Open ON: Unlock
Lock S/W
10 As DR Lock S/W Lock = Open, Unlock = GND Lower than 1 volt/Open ON: Unlock
RR LH, RR RH, T/Gate Unlock =
RR RH DR Lock GND
11 Lower than 1 volt/Open ON: Unlock
S/W RR LH, RR RH, T/Gate Unlock =
Open
12 Tail gate S/W Open = GND Lower than 1 volt/Open
Tail gate Key
13 ON = GND Lower than 1 volt/Open ON: Unlock
Unlock S/W
14 Hood S/W Open = GND Lower than 1 volt/Open
Drive Door Key
15 ON = GND Lower than 1 volt/Open ON: Lock
Lock S/W
16 Driver Door ON = GND Lower than 1 volt/Open ON: Unlock
Assist DR Key
17 ON = GND Lower than 1 volt/Open ON: Lock
Lock S/W
Assist DR KEY
18 ON = GND Lower than 1 volt/Open ON: Unlock
Unlock S/W
ON: Higher than7volts
19 Washer S/W ON = BAT
Off: Lower than 4volts
ON: Higher than7volts
20 INT. S/W ON = BAT
Off: Lower than 4volts
21 INT. Volume S/W 0V ~ 2.5volts - 0Ω~ 50KΩ
22 Front Deicer S/W ON = GND Lower than 1 volt/Open
23 RR. Defogger S/W ON = GND Lower than 1 volt/Open
24 Tail Lamp S/W ON = GND Lower than 1 volt/Open

5 Chonan Technical Service Training Center

JM - ETACS

Recognition
No Input signal Condition Remarks
ON/OFF voltage level
25 Front Fog L/P S/W ON = GND Lower than 1 volt/Open
26 RR. Fog lamp S/W ON = GND Lower than 1 volt/Open
27 Head Lamp S/W ON = GND Lower than 1 volt/Open
29 Air bag signal ON = GND (Deployed) Lower than 1 volt/Open
Low: Lower than 1 volt
30 Speed Sensor VSS Pulse (PULSE:0
5V)
Hi: Higher than 4volts

1.4 ETACS function items

1) Wiper control
- Washer & Wiper
- Speed sensing intermittent wiper control
- Variable intermittent wiper control
2) Seat belt warning timer control
3) Key operated warning control
4) Front windows deicer control
5) Rear windows defogger control
6) Room lamp delay control
7) Rear fogger lamp control
8) Tail lamp auto cut control
9) Ignition keyhole illumination control
10) Door lock/unlock control
- Central door lock control
- Auto door lock control
JM ETACS
- Ignition key reminder
- Crash door unlock
11) Power window timer control

1.5 Anti theft function

- Arm function
- Disarm function
- Alarm function
- Panic function

6 Chonan Technical Service Training Center

JM - ETACS

1.6 Input / Output signal

Battery (Back-up Voltage)

Ignition 1 & 2(Power Voltage)
Alternator “ L “ Terminal
Washer Switch
Wiper INT. Switch
Wiper Motor Relay
Wiper INT. Volume Resistor
Defogger Relay
Rear WDW. Defogger Switch E
Seat Belt Warning Indicator
Front deicer switch T
Chime Bell
Seat Belt Switch A
Power Window Relay
Door Warning Switch C
Central Door Lock Relay
Driver’s & Assist DR lock switch S
IGN. Key Hole Illumination
All Door S/W (each door S/W) C
Tail Lamp Relay
Assist DR switch M
Room Lamp
Driver’s door switch
Fog Lamp Relay
Vehicle Speed Sensor
Air bag crash signal
Tail Lamp Switch Keyless Antenna

Fog Lamp Switch

Etc

* The antenna location can be changed

for better quality without notice.

Chimebell

ETACSCM

7 Chonan Technical Service Training Center

JM - ETACS

2. ETACS function
2.1 Washer & intermittent wiper control Description & operating chart
1) When the ignition switch is "on", and if turn the washer switch on, wiper output become "on"

after 0.3sec. and turn the washer switch off, wiper output become "off" after 2.5 3.8sec.
Iignition switch On
Off
Washer S/W Off
On T2
Wiper motor On T1
Output Off
T1:0.6 sec, T2:2.5~3.8 sec.

2) The output of wiper related to washer become "on" when the washer switch is turned on for
min 0.6sec in operating of INT. wiper and behave as like wiper mist function when the washer
switch is turned on for 0.2 0.6sec.
T1 More than 0.6 Seconds Less than 0.6 Seconds
Washer Off
switch On

T3 Within T3 T3
Wiper On T2
Output Off

T1:06 Seconds, T2: 0.3Sec. T3:INT. Time

3) Wiper mist
The output of wiper motor become "on" during mist switch ‘on”.

Washer Off
T1
switch On T2
Wiper On
output Off
T1: 0.2~0.6 sec, T2: 0.6~0.7 sec

8 Chonan Technical Service Training Center

JM - ETACS

4) Speed sensing wiper control

Speed sensing intermittent wiper
Control the intermittent time of INT. wiper as vehicle speed is changed.
- "On" state of ignition switch.

- "INT" state of wiper switch.

- Set up vehicle speed, intermittent time and input volume value

change the wiper speed(with calculating intermittent time form vehicle speed)

1) Vehicle speed input calculates vehicle speed in the form of input pulse per a second.
60 [ km/h ] × 60 [ sec ]
1 [ pulse/sec ] = ------------------------------- 1.41 [ km/h ]
637 × 4 pulse
2) Vehicle speed output

Vehicle speed was counted input pulse per second, and than choose max. value (compare new

value with old value).

V = max (v new, v old) V new : new v/speed

V old: old v/speed
3) Intermittent time ratio (vehicle speed: 0km/h)

Calculate intermittent time ratio from set up intermittent time volume (input voltage)

intermittent time ratio is corrected by input voltage linearly, according as expressed volume

position from slow (100%) to fast (0%) of set up knob.

100
90
INT TIME RATIO(%)

80
70
60
50
40
30
20
10
0
0 0.5 1 1.5 2 2.5
INPU T VO LTAG E(V)

9 Chonan Technical Service Training Center

JM - ETACS

4) Base intermittent time output

Calculate intermittent time at intermittent time ratio 100% and 0% from vehicle speed of

No.(2)(by correction of intermittent time linearly). And then calculate base intermittent time

with quota allotment method from intermittent time ratio of No (3).

do not be renewed base intermittent time if variation of intermittent time is max. 0.3sec.

operate continuously if base intermittent time is max. 2sec.

operate wiper if start(from 0km/h to 7km/h) vehicle when intermittent time timer (passage

time)is more than 10sec.

20.0
18.0 18.0
INT TIME(sec)

16.0
14.3
14.0 12.9 12.2
12.0 11.5
10.9 10.4 10.2 10.0 100%
10.0 10.0 0%
8.0
6.0
4.0 2.6 2.4 2.2 1.9 1.6 1.4 1.3 1.2
2.0 1.1
1.0
0.0
0.0 11.2 22.4 33.6 44.8 56.0 67.2 78.4 89.6 100.8

SPEED(km /h)

Volume S/W Intermittent time (sec) ±10%

Remarks
Input voltage 0Km/h 20Km/h 40Km/h 60Km/h 80Km/h 100Km/h

0.0V 2.6S 2.2S 1.7S 1.3S 1.2S 1.0S

1.0V 4.2S 3.3S 2.7S 2.2S 2.1S 1.9S

1.5V 5.7S 4.8S 3.7S 3.2S 3.0S 2.8S

2.0V 9.5S 7.1S 6.2S 5.5S 5.2S 5.0S

2.5V 18.0S 13.0S 11.7S 10.6S 10.1S 9.9S

10 Chonan Technical Service Training Center

JM - ETACS

2.2 Seat belt warning timer

2.2.1 Description

1) The seat belt warning lamp signal (period: 0.6sec) and the seat belt warning lamp signal

(period: 0.6sec) output for 6sec with duty (50%) from the ignition is "on".

2) The lamp and the chime bell output are turned off if the ignition is "off" within the time.

As soon as the seat belt switch is "on" within the time, chime bell output is "off" immediately

but seat belt warning lamp output for rest time.

3) The warning lamp and the chime bell output are always "on" if the seat belt is taken off after
putting on the seat belt when the ignition is "on" state.

2.2.2 Operating time chart

Ignition On
Switch Off
Seat belt On
S/W(N/C) Off T1

T1
Chime On
bell Off
S/Belt On T3
lamp Off
T2
T1 T1

T1 : 6 ±1 sec. T2 : 0.3 ±0.1 sec , t3 : 0.45 ±0.1 sec

11 Chonan Technical Service Training Center

JM - ETACS

2.3 Key operated warning

2.3.1 Description
1) Chime bell output continuous signal (cycle 0.9sec, duty 50%), when open the door if insert
key in the key cylinder.
2) Make sure that the output come to "off" when the door is closed or the key is removed from
the key cylinder.

2.3.2 Operating time chart

Door warn’g key in
switch key out
Driver’s open
door close
Chime on T1 T2
Bell off
T1,T2 : 0.45 sec ±0.1 sec

2.4 Rear windrow Defogger timer & Front deicer (including outside mirror heated)
2.4.1 Description

1) The output of defogger is "on" for 15 or 20min when the defogger switch is "on" in case

alternator “L” terminal signal is in the "charging voltages high" position.

2) Make sure that defogger's output is "off" if the defogger switch is "on" again when the output is

still "on" state.

3) Make sure that defogger's output is "off" if the alt l's changed to "low" when the output is still
"on" state.
2.4.2 Operating time chart
Alternator High
“L” signal Low
Defogger On
Switch Off
Defogger On
output Off T1 T1 T1

T 1:15 ± 3 min or 15 ± 3 min

12 Chonan Technical Service Training Center

JM - ETACS

2.5 Delay out room lamp

2.5.1 description

1) Lamp is "on" when door is opened (door switch is "on").

As soon as door is closed (door switch is "off") 75% of light disappear and the rest decay

slowly come to the light off after 5 6 sec.

2) Make sure that no operation when time of door switch "on" is under 0.1 sec.

3) Make sure that analysis capacity is more than 32 step when light was decayed.

4) Make sure that the output is off as soon as the ignition switch is turned on during delaying and

decaying operation.
2.5.2 operating time chart
Door S/W Open
(4door) Close
Ignition On T1
S/W Off
Room lamp On 75%
output Off

T1 : 5.5 ±0.5 sec

2.5.3 Room Lamp Delay Out after receive “Keyless Unlock” signal.
1 The room lamp lights “OFF” after lighting “ON” about 30 sec on condition that door is closed.
2 The room lamp prolongs light “ON” about 30 sec. Again, If the TX button unlocks during this
condition.
3 The room lamp keeps lighting “ON” in light “ON” when opening the door, the room lamp is back
to the delay function.
4 The room lamp lights “OFF” immediately and signals alarm if the keyless lock is.

13 Chonan Technical Service Training Center

JM - ETACS

2.6 Lamp auto cut (tail lamp only)

2.6.1 Description 1
1. In case of the tail lamp switch is turned ON after IG. SW ON or the driver door is opened
after IG. SW OFF, the tail lamp is extinguished automatically.
2. In addition, the IG. SW is turned OFF after driver door is opened with IG. SW is ON
condition, the tail lamp will be extinguished automatically too.
3 After automatic extinguish, if the tail lamp switch is turned ON again, then, the tail lamp
will be ON (illuminating) and the auto cut function will be released.
2.6.1 Operating time chart
Ignition On
Lamp auto cut Lamp auto cut
switch Off
Tail lamp On
switch Off
Driver’s On
Door S/W Off
Tail lamp On
relay Off

2.7 Ignition keyhole illumination

2.7.1 Description
1) Ignition keyhole illumination is turned on when driver door is opened (at Ignition switch "off").
2) Make sure that the output is "off' after delaying "on" state of ignition key hole illumination for
10sec when the driver door is closed in case of No (1) state.
3) Make sure that the ignition key hole illumination is turned off if the ignition input is accepted in
case of No. (1),(2) state.

2.7.2 Operating time chart

Ignition on
Switch off
Driver open
door close
T1 T1 T2
Ignition key. on
hole ill off
T1 : 10 ±1 sec , T2 : 0 ~ 10 sec

2.8 Auto door lock control

2.8.1 Description

14 Chonan Technical Service Training Center

JM - ETACS

Door lock function is operated automatically in bellow condition, when vehicle speed is more
than 40 Km/h while the engine is running.
1). IG. Switch is ON.
2.) Vehicle speed is more than 40 Km/h.
The signal of vehicle speed 40 Km/h is receive in ETACSCM.

Ignition On
Key Off
Vehicle 40km/h
Speed 0km/h T1 : 1.0 ± 0.5 sec.
Door lock On
relay Off
Door Unlock
actuator Lock

2.9 Central Door Lock Control by Remote Controller 2.9.1 Description

The ETACS module receives “Lock/Unlock” signal from the transmitter, and outputs door “Lock
or Unlock.
■ Operating Condition When the IG. Key is removed from key cylinder.
When the SET/OFF switch on keyless entry system receiver is put on the “OFF”
(Operation mode)
2.9.2 Operating time chart
TX Lock On
Button Off
Unlock Button pushed
TX unlock On
Button Off
T2 T1
DR lock On
Output Off
DR. unlock On
Output Off
T1 T1
Hazard On
Lamp Off
* T1 : 0.5 ± 0.1 sec. * T2 : MAX 0.3 sec.

2.10Ignition Key Reminder Control

2.10.1 Description
This function is to prevent vehicle from Lock if IG. Key is inserted into key cylinder.

15 Chonan Technical Service Training Center

JM - ETACS

1) IG. Key is inserted into key cylinder.

2) The signal of IG. Key insert condition is perception in ETACSCM.
3) At this time if pushed door lock knob of front LH or RH door, door unlock signal output for
1 sec.
4) So, that during insert key into the key-cylinder to prevent door lock.

2.10.2 Operating time chart

Key insert
DR warning ON
Switch KEY REMOVED
OFF
FRT LH/RH ON
DR S/W OFF
T2
FRT LH/TH Unlock
DR Lock Lock
T1 T1 T3 T4
S/W T4
DR LOCK Unlock
Actuator
Lock
Unlock Output T2
T2 T2
* T1 : 0.5 ± 0.1 sec. * T2 : 1 ± 0.1 sec. * T3 : 0.5 ±0.1 sec. * T4 : MAX 0.5 sec

2.11 Crash door unlock

2.11.1 Description 1) If the airbag signal is inputted to the ETACS when the door is locked, the
unlock signal is
executed immediately for safety.
2) At this time, all doors should be locked for operating above “unlock execution”.2.11.2

16 Chonan Technical Service Training Center

JM - ETACS

Operating time chart

Air Bag Deploy Deployment
Condition Normal
T1
Air Bag Module High
Crash Signal Low
T2 Door unlock signal output
Door Unlock Unlock
from A/BAG control module
Output signal Lock
T3

Door Lock Unlock

Actuator Lock
T1: 200 mSEC. T2: 40mSEC. T3: 5 sec.

2.12 Auto Door Unlock Control“1” after IG. Off

2.12.1Description
1). When IG. S/W is turned OFF, the door lock is controlled to UNLOCK from ETACSCM.
2) If IG. SW is turned OFF, unlock signal is output control door unlock relay in ETACSCM.

2.12.2 Operating time chart

Ignition ON
Switch
OFF

DR Actuator Unlock
S/W
Lock
T1
DR Lock Unlock
Relay
Lock
* T1 : 0.5 ± 0.1 sec.

2.13 Ignition keyhole illumination

2.13.1 Description
1) Ignition keyhole illumination is turned on when driver door is opened (at Ignition switch "off").
2) Make sure that the output is "off' after delaying "on" state of ignition key hole illumination for
10sec when the driver door is closed in case of No (1) state.
3) Make sure that the ignition key hole illumination is turned off if the ignition input is accepted in
case of No. (1), (2) state.

17 Chonan Technical Service Training Center

JM - ETACS

2.13.2 Operating time chart

Ignition on
Switch off
Driver open
door close
T1 T1 T2
Ignition key. on
hole ill off
T1 : 10 ±1 sec , T2 : 0 ~ 10 sec

2.14 Power window timer

2.14.1 Description
1) Turn the output of power window on when the ignition switch is "on".
2) Stop outputting "off" after maintaining for 30sec when the ignition switch is "off",
3) As soon as driver or assistance door is opened, the output comes to "off" in No (2) state.
4) Make sure to remain "on" the power windows main relay for 30sec. in the power windows
up/down operation by keyless.

2.14.2 Operating time chart

Ignition on
Switch off
T1 : 30 ±5 sec
Driver’s door open
(Assist’s door) close
T1 T1

Power window on
output off

3. Anti theft function (Keyless entry)

3.1 General
- Door lock/unlock control by remote control (Keyless entry)
- Thief alarm device (Burglar alarm)

3.2 Anti theft operation prohibition condition.

- In case of ignition key was inserted in height cylinder

18 Chonan Technical Service Training Center

JM - ETACS

- When receive ignition's signal in ETACSCM

3.3 Transmitter

Frequency
EU, AUS, GEN: 433.9 MHz
NAS, JPN: 313.85 MHz

Transmission distance : 10 m
Coding: Rolling code

3.4 Input signal for anti theft system

3.4.1 Strobe control
In order that the parasitic current of ETACSCM reduces, all of input signal into ETACS module is
monitored and detected by the method of strobe.
Strobe intermittent control to reduce the parasitic current in ETACS

ON (S/W Close): 5 volt

CPU sleep state
OFF (S/W Open): 0 volt CPU SLEEP

Note 2020ms 280

280 ms
When measuring the input signal voltage of strobe type by using general multi-meter, be careful
and don’t make confuse that the measuring voltage checks 1-2 volt due to fast speed in 300ms a
1cycle.

Strobe Control Inputs signal Item (Signals related with Anti theft system)
Driver’s Door Switch Door Unlock Switch Tail gate Switch
All Door Switch Door Lock/Unlock Switch(4 or 5 switch) Hood Switch

3.5 Transmitter signal reception process

Rolling Code Signal

Transmitter (TX)
Lock button Receiver (RX) ETACS

Unlock button CM
Lo. Signal by Time
Rolling Code Example.
Lock: 50 ms.
3F50C19 19 Chonan Technical Service Training Center
Unlock: 100 ms.
3F50C20
JM - ETACS

3.6 Anti- theft system input & output signal

Input signal

Battery (Back-up Voltage)

Power Voltage (from IGN. switch)
Transmitter Lock/Unlock Signal
Output actuator
Door Lock/Unlock S/W (Located in each
E
Door Lock Actuator)
T Alarm horn Relay
FRT. LH/RH Door Lock/Unlock Switch
A Hazard Relay
RR. LH&RH Door Lock/Unlock Switch
C Burglar Alarm Relay
All Door Switch (Located in each Door)
S Central Door
All DR SW (FRT.LH&RH, RR. RH&LH)
C Lock/Unlock Relay
FRT LH/RH Door Switch
M
Front Drivers Door Lock S/W
Front Assist Door Locj S/W
Tailgate Switch
Rear Window Switch
Hood Switch

3.7 Anti theft function detail

- Arm function
- Disarm function
- Alarm function
3.7.1 Arm function
1. If the ETACS receives the “Lock” signal from transmitter. (When IG key removed from key
cylinder and all switches are closed) ETACS outputs “ON” the “Lock” outputs and vehicle
becomes “Armed condition” with turn on the Hazard lamp for 1 sec. after confirming lock signal
of door lock actuator.

20 Chonan Technical Service Training Center

JM - ETACS

2. If the ETACS receives the “Lock “ signal from transmitter when any one switch of all door
switches is open, it outputs “ON” the “Lock” output only, In this case, ETACS does not output
Hazard lamp “ON” and the vehicle does not “Armed”
3. The door is closed in the above “2” condition, ETACS output “ON” the Hazard lamp for 1sec.
And the vehicle is armed.
4. If lock button on the transmitter is pushed again under “Armed” condition, only Hazard lamp is
“ON” for 1sec. With maintaining armed condition.
Only the transmitter can make the “Armed” condition for the vehicle.
Function time chart

Input Open
Signal Close
Transmitter Lock
signal Unlock
Door lock On T1

output Off
Hazard On T2

lamp Off
Arm Arm T3
state Disarm Disarm Arm

T1 : 0.5 sec, T2 : 0.5±0.1 sec. , T3 : 2 sec. , T4 : Within 2 sec.

3.8 Disarm function

1. When TX unlock button pushed, door unlock output and the vehicle is “Disarmed”.
At this time, Hazard lamp output “ON” twice.
2. If unlock (TX) button is pushed again under “Unlocked” condition, only Hazard lamp
output “ON” twice. In this case, door unlock is not output again
To disarm impassible using by IGN. Key
Function time chart
Transmitter Lock
Button Unlock

21 Chonan Technical Service Training Center

JM - ETACS

Unlock On
Output Off
Arm Arm
State Disarm
Hazard On
Lamp Off

Others disarming condition

- When input unlock signal from transmitter
- When ignition key “ON”
- When driver’ & assist door key switch off to on. (NAS only)
- When tail gate switch off to on. (NAS only) at this time operate hazard twice when cancel by
tail gate unlock switch

3.9 Alarm function (General area)

When receive more than one of entrance signal at arm mode, start inhibit is turned on and keep
the alarm on for 27sec(±0.3sec), off for 10sec±0.3sec) and then repeat this 3 times. (The output
of hazard lamp is also on)

Condition Arm
Disarm Arm Disarm
Disarm
Signal Open
Input Close
T1 T2
Alarm On

T1 22 T1 Chonan Technical
T1 Service Training Center
JM - ETACS

Horn Off
Hazard On
Lamp Off

T1 : 27 ±0.3sec, T2 : 10±0.3sec , T3 : 0.5±0.3sec

3.10 Panic function

If the panic button of transmitter is pushed whether the system is Arm or Disarm, hazard lamp and
siren is on for about 30sec. And the panic button reselected, siren and lamp come off.

Arm
Arm
Arm State Disarm
Disarm
ON
Panic Button
OFF
ON
Siren
OFF
T1 T1
Arm
Arm State Arm Disarm
Disarm
ON
Panic Button
OFF
ON
Siren
OFF
T2 T1
T1 T2
T1 : 27± 2 sec. T2: Panic button pressed from 1st to 2nd.
During Panic operation, if is below condition, panic is release
- When pushed lock or unlock button of transmitter
- It ignition key inserted to key cylinder. (Key operated warning switch)
- When front RH/LH door switch signal ON to off or off to ON.
- When tail gate unlock switch off to on

4. Diagnosis
4.1 Current data
It is available to diagnose the JM ETACS by communicating with Hi-scan.

23 Chonan Technical Service Training Center

JM - ETACS

General M/East
EC, Aust.
(Except M/East) (Except Brazil)
Items
Non- Non- Non-
Keyless Keyless Keyless
Keyless Keyless Keyless
IGN1 O O O O O O
IGN2 O O O O O O
ALT L O O O O O O
Key IN Sw O O O O O O
Sarter Inhibit relay O X O X O X
Power window relay O O O O O O
Tail Lamp Sw O O O O O O
Rear Fog Sw O O X X X X
Head Lamp Sw O O X X X X
Front Fog Sw O O X X X X
Tail Lamp Relay O O O O O O
Rear Fog Relay O O X X X X
Hazard Lamp Relay O X O X O X
Driver Seat Belt indicator O O O O O O
Room Lamp Output O O O O O O
IGN Key hole illumination O O O O O O
Driver Door Open Sw O O O O O O
Assist Door Open Sw O O O O O O
4 Door Open Sw O O O O O O
Hood Open Sw O X O X O X
Tail Gate Sw O O O O O O
Driver Door Actuator Position Sw O O O O O O
Assist Door Actuator Position Sw O O O O O O
Driver Door Key Lock Sw (US only) X X X X X X
Driver Door Key Unlock Sw (US only) X X X X X X
Assist Door Key Unlock Sw (US only) X X X X X X
Clash Unlock Signal (DOM, JPN only) X X X X X X
MTS Door Unlock Signal (DOM only) X X X X X X
MTS B/alarm Signal (DOM only) X X X X X X
Door Lock Relay O O O O O O
Door Unlock Relay O O O O O O

24 Chonan Technical Service Training Center

JM - ETACS

2-Turn Unlock (D/Lock) Relay (US only) X X X X X X

Rear Door Actuator Position Sw O O O O O O
Assist Door Key Lock Sw (US only) X X X X X X
Tail Gate Key Unlock Sw (US only) X X X X X X
Washer Sw O O O O O O
INT Sw O O O O O O
Defogger Sw O O O O O O
Wiper Relay O O O O O O
Defogger Relay O O O O O O
Front Deicer Sw O O O O O O
Front Deicer Relay O O O O O O
Driver Seat Belt Sw X X O O O O
Burglar Horn Relay O X O X O X
Chime Buzzer (DOM, US, JPN only) X X X X X X
Chime Bell X X O O O O
INT volume O O O O O O
Speed signal O O O O O O
Tx Data Record O X O X O X
** This current data can be changed without notice while developing the vehicle.

4.2 Actuator driving

General M/East
EC, Aust.
(Except M/East) (Except Brazil)
Items
Non- Non- Non-
Keyless Keyless Keyless
Keyless Keyless Keyless
Lock Relay O O O O O O
Unlock Relay O O O O O O
Dr Unlock Relay (US only) X X X X X X
Power Window Relay O O O O O O
Wiper Relay O O O O O O

25 Chonan Technical Service Training Center

JM - ETACS

Hazard Relay O X O X O X
Burglar Horn Relay O X O X O X
Starter Inhibit Relay O X O X O X
Tail Lamp Relay / DRL Unit O O O O O O
Rr Fog Relay O O X X X X
Fr Deicer Relay O O O O O O
Rr Defogger Relay O O O O O O
Dr Seat Belt Indicator O O O O O O
IGN Key Illumination O O O O O O
Chime Bell X X O O O O
Chime Buzzer (DOM, US, JPN only) X X X X X X
Room Lamp O O O O O O

4.3 DTC List

General M/East
EC, Aust.
(Except M/East) (Except Brazil)
DTC Items
Non- Non- Non-
Keyless Keyless Keyless
Keyless Keyless Keyless
B1900 INT volume O O O O O O
B1902 IGN Key Illumination O O O O O O
B1903 Burglar Horn Relay O X O X O X
B2106 Power Window Relay O O O O O O
B2107 Hazard Relay O X O X O X
B2108 Wiper Relay O O O O O O
B2110 Lock Relay O O O O O O
B2111 Unlock Relay O O O O O O
B2112 Dr Unlock Relay (US only) X X X X X X
B2114 Tail Lamp Relay / DRL Unit O O O O O O
B2115 Rr Defogger Relay O O O O O O
B2116 Rr Fog Relay O O X X X X
B2119 Fr Deicer Relay O O O O O O
B2120 Dr Seat Belt Indicator O O O O O O

26 Chonan Technical Service Training Center