Forage Bag
Forage Bag
Forage Bag
FORAGE BAG
Designed by Anna Graham of Noodlhead for RK
www.noodle-head.com
A petite set of cross body bags. Zippered front opening is perfect for easy and secure access
to your most important items and elegant darts help bring shaping to the bag as well as
adding sophisticated detail. Interior pocket (regular size only) is perfect for a pen and phone.
Cutting Instructions
Please note that pieces are cut from pattern pieces as well as rectangular measurements.
Use a gridded ruler, rotary cutter, and cutting mat to cut the rectangular pieces to size.
Step 2: Main Panel pieces cut to dotted line will be referred to as Front Panel pieces, Main
Panel pieces cut to full pattern piece height we be referred to as Back Panel pieces. With
a water soluble pen, mark on the interfacing indicating which piece is which so as to avoid
confusion during construction.
Figure 1
Figure 2
page 4
Make Strap
Step 1: Place strap pieces RST and sew along one short end. Press seam open. Fuse
interfacing {end-to-end for mini} on wrong side.
Figure 3
Step 2: Fold strap in half lengthwise WST. Open and press raw edges to center crease. Fold in
half again and press. Strap will be 1/2” wide.
Figure 4
Figure 5
Step 2: Fold continuous strip in half lengthwise WST. Open and press
raw edges to center crease (or use bias tape maker and follow
manufacturer’s instructions). I find that spray starch works great for
nice crisp edges.
Figure 6
Step 3: Fold in half again and press. Now you’ll have 1/2”-wide
double fold bias binding. Set aside.
Figure 7
page 5
Make and Attach Interior Slip Pocket (Regular size only)
Step 1: Place Interior Slip Pocket pieces
RST. Sew along all edges leaving a 4”
opening along one side edge. Clip
corners and turn right side out. Use
turning tool (or chopstick) to push out
corners. Press.
Figure 8
Step 2: Topstitch along top (6”) pocket edge. Add additional row of topstitching as desired.
Step 3: Center pocket 1-1/2 ” down from top (straight edge) on lining Back Panel piece. Pin
in place.
Step 4: Sew along sides and bottom of pocket, beginning and ending with a small narrow
triangle in each corner for reinforcement.
1½”
2
1
3
Figure 9
Prepare Zipper
Press one short end of each Zipper End Tab to the wrong
side by 1/2”. End Tabs will now measure 1” tall by 2” wide.
Place folded edge aligned to just past the zipper end stop.
Two End Tabs will be sandwiching the zipper. Topstitch
in place. Repeat for remaining End Tabs and remaining
zipper end. TIP: Glue will be very helpful for keeping these
little pieces in place before you topstitch.
Figure 10
page 6
Assemble Bag
Step 1: With exterior Front Panel right side Front Panel
up, center prepared zipper right side down (exterior fabric) zipper right side down
(zipper pull at left) on top aligned to top
straight edge. Glue or pin in place along
zipper tape.
Figure 12
Figure 13
page 7
Top Accent
(accent fabric)
Back Panel
(lining fabric)
Step 8: Press Top Accent pieces away from zipper,
Front Panel WST. Topstitch along zipper through all layers.
(exterior fabric)
Figure 14
Front Panel
(exterior fabric)
Figure 16
page 8
Back Panel
(exterior fabric)
Back Panel
(lining fabric)
ma
Step 11: Press Back Panel pieces away
from Top Accent, WST.
Top Accent
Step 12: Topstitch along exterior Back (accent fabric)
Panel fabric along the Top Accent seam
through all layers.
Front Panel
(exterior fabric)
Figure 17
page 9
Construct Bag
Step 1: Machine baste layers together with wrong sides of the fabric together, around entire
perimeter using a 1/4” seam allowance. Note: Exterior and lining of the front will be wrong
sides together, and exterior and lining of the back will be wrong sides together. TIP: Finger
press darts in opposing directions to ‘nest’ the dart seam and reduce bulk.
Note:
Finish the inside raw edge with the bias
binding strip you prepared earlier. Because
the upper top edge of the bag will not
be seen once the grommets are installed
in the next step, the bias tape at the top
corners of the bag can be left raw. Figure 18
Step 4: Unfold binding and align long raw edge with raw edge of bag. Right side of binding
will be facing right side of lining Front/Back Panel. Beginning at top corner, sew binding in
place by sewing on the first crease of binding (towards raw edge of bag).
Step 6: Slide zipper all the way open, turn bag exterior side out. Press carefully along curved
bottom edges to get a nice smooth edge.
page 10
Install Grommets
Step 1: Make a mark 1” from top and 1-1/2” {1”} from
each side edge of Top Accent. Mark grommet hole
on Top Accent by centering grommet over marking
and tracing the inner diameter of grommet onto
Top Accent piece using a water-soluble pen. Using 1”
a sharp scissors, cut hole through all layers of Top
Accent.
1½” {1”}
Step 2: Set both grommets by inserting grommet post
through front side of the bag, flipping bag over, and
placing grommet washer over grommet post. Use
the setting tool for your particular grommet to set
each grommet by hammering it secure. Grommets Figure 20
will be snug to the fabric when set correctly.
Insert Strap
Thread Strap through grommet and double knot to secure in place. Trim excess end of raw
edge of Strap at an angle and seal with seam sealant if desired. Repeat for remaining end
of Strap through remaining grommet, adjusting overall length if needed.
page 11
Templates
Test Box:
When printed at
100% this box will
measure 1’’ square.
FORAGE BAG
Main Panel (Regular)
PLACE ON FOLD
Cut 8 on fold:
2 exterior fabric (cut 1, then cut 1 cut to dotted line)
2 lining fabric (cut 1, then cut 1 cut to dotted line)
4 fusible woven interfacing (cut 2, then cut 2 cut to dotted line)
page 12
Test Box:
When printed at
100% this box will
measure 1’’ square.
FORAGE BAG
Top Accent (Regular)
Cut 4
2 accent fabric
2 fusible woven interfacing
page 13
Test Box: Cut to dotted line for Front Panel
When printed at
100% this box will
measure 1’’ square.
FORAGE BAG
Main Panel (Mini)
PLACE ON FOLD
Cut 8 on fold:
2 exterior fabric (cut 1, then cut 1 cut to dotted line)
2 lining fabric (cut 1, then cut 1 cut to dotted line)
4 fusible woven interfacing (cut 2, then cut 2 cut to
dotted line)
page 14
Test Box: Cut to dotted line for Front Panel
When printed at
100% this box will
measure 1’’ square.
FORAGE BAG
Main Panel (Mini)
PLACE ON FOLD
Cut 8 on fold:
www.noodle-head.com 2018
dotted line)
2 accent fabric
This pattern may be used for personal purposes only and may not be reproduced in any form without the
express permission from Robert Kaufman Fabrics. This pattern is not for resale. All patterns, unless otherwise
attributed, are © Robert Kaufman Co., Inc. 2005-2018. All rights reserved.
page 15