Seal Bore Packer System - Retrievable
Seal Bore Packer System - Retrievable
Seal Bore Packer System - Retrievable
MODEL”BRSB” RETRIEVABLE HYDRAULIC SEAL Remove test plugs and test pins.
BORE PACKER Lower the Packer slowly to the required position. Be careful when
Product No. BI 646-88 entering Liners.
Install and land Tubing Hanger.
DESCRIPTION:-
Test the Tubing by running a Standing Valve in a Nipple above the
Model “BRSB” Retrievable Hydraulic Seal Bore Packer.
Packer is a Retrievable Packer, Hydraulically set
Install the well head.
by pressure in the Tubing. It is run with BH
Hydraulic Setting Tool and the retrieving is done Displace the mud with a “completion” fluid in the annulus by
independently from the Tubing, using a introducing a lighter fluid such as diesel or gas oil into the
Retrieving Tool manipulated on a work string. tubing.
This packer is ideally suited for highly deviated
well both onshore and offshore. Run the Standing Valve into the Seating Nipple under the Packer.
Remain attached to the Standing Valve
APPLICATIONS : - Apply a pressure to set the Packer - this Should be done without
stopping pumping.
Model “BRSB” Retrievable Hydraulic Seal Bore
Packer can be used in oil production wells or in SETTING PROCEDURE :-
water or gas injection wells. It is also called
"ERD" Packer. Pressure is applied on the bottom of the piston contained by O -
ring which shear the Shear Screws.
ADVANTAGES : -
The packings are then packed off.
Run and set with the Production Tubing.
The Shear Pins are sheared allowing the upper slips to come in
Hydraulic setting eliminates the requirements contact with casing, followed by the Shear Pins shearing and
for spacing out and opening and closing with the allowing the lower slips to come in contact with the casing as well.
help of Sliding Sleeves for the displacement of
fluids. The pack-off is mechanically held in position by the body lock ring.
Retrieval independent of the Tubing using a Put set down weight on the Packer and turn to the right to engage
Retrieving Tool. It can be left at the bottom of the the collet of the Retrieving Tool under the Supporting Sleeve of
well with a By-pass Blanking Plug in a Nipple to the Packer.
isolate the formation.
Once the screws have sheared the Support Sleeve move upwards
Opposed slips (without hold down) positioned freeing the support beneath the fingers of the collet. The collet
flexes and detaches itself from the thread linking it to the base of
Available for standard, H2 S (or CO2) Service, NACE MR 01-75. the housing . By upward movement of the body of the Packer, the
compression of the Packing Element is released and the Slips get
OPERATION :- retracted. The Setting Sleeve is supported by the Ring which
rests on the top of the piston above the O-ring.
RUNNING :
SPECIFICATION GUIDE
Check that the outside diameter corresponds to the weight of the FOR BRSB PACKER
tubing.
CASING TUBING “BRSB” PACKER
Install the test pins in the corresponding holes, hold them in place 5-1/2 17-20 2.688 2.690 4.552 115.620
AS
ODERED
with an elastic band or adhesive strip. 23-29 3-1/2 4.000 5.955 151.2 4-1/2 2.992 75.99
7
AS
Pressurize the assembly and make sure that there are no air 32-35 4-1/2 4.000 5.80 147.32
ODERED
2.992 75.99
55
SEAL BORE PACKER SYSTEM RETRIEVABLE
WIRE LINE ADAPTER KIT
Product Nos. BI 438-09
56
SEAL BORE PACKER SYSTEM RETRIEVABLE
MODEL "BH" HYDRAULIC SETTING TOOL FOR MODEL “BR” RETRIEVING TOOL
MODEL “BD” PERMANENT PACKER AND Product No. BI 646-71
RETRIEVABLE HYDRAULIC SEAL BORE PACKER
Product No.:- BI 414-71 DESCRIPTION:-
DESCRIPTION:- The model “BR” Retrieving Tool is used for retrieving MODEL
“BRSB” Retrievable Hydraulic Seal Bore Packer.
The model "BH" Hydraulic Setting Tool is used to set MODEL The latch of the Retrieving Tool is engaged in the Top Box
BD Permanent Packer and Model "BRSB" Retrievable Hydraulic Thread of the Seal Bore Packer.
Seal Bore Packer.
Which is a left hand sq. thread. Put Set down weight 3000-
The Packer is run in the model “B” Wire Line Adapter Kit, 5000 Lbs on the Packer and turn to the right to engage the collet of
attached to the model “BH” Hydraulic setting tool on the drill pipe the Retrieving Tool under the supporting sleeve of the Packer.
and lower to setting depth. The tubing fills automatically as it is run
in, though a ported top sub in the setting assembly. The ports also PULL! In principle the Packer should release with a pull of 5-
permit circulation at any time. A 1 7/16” Brass Ball is pumped down 10 tons. Once the screws have sheared the support sleeve moves
to seat in the hydraulic setting tool. Approximately 1500 psi is upwards freeing the support beneath the finger of the collet The
applied to set the packer slips. Following which the pressure is latter can then flex and detach itself from the thread linking it to the
released and / or tension applied to shear the release stud of the base of the Housing. On upward movement of the body of the
Wire line Adapter Kit. The Hydraulic Setting Tool along with wire line packer the compression of the packing element are Released and
adapter kit can then be retrieved leaving the packer set in hole. the slips retracted. The Setting Sleeve is supported by the Ring,
which rests on the top of the Piston above the O-ring.
SUPPORT SLEEVE
LOCK NUT
PISTON
CYLINDER
CYLINDER CONNECTOR
PISTON ROD
CYLINDER HEAD
LOCK RETAINING RING
SETTING MANDREL
57
MODEL “BC-2RAH” RETRIEVABLE SEAL BORE PACKER
SPECIFICATION GUIDE
Size Ca sing Weight Preferred Range of Gauge Lower Upper M in. Bore Seal Retrieving
Size Range Casing ID’s R ing Bore(in Bore Thru Seal Assembly Tool Size
( PP F) Min. Max. O.D(in) ) Size
(in) (in)
84A4 – 5.812 3.250 4.000 3.250 80DA40 80-40x32
40 x 32 29-35 5.879 6.189
84A4 – 7 5.820 3.875 81FA-47
47 x 38 OR OR 80-47x38
84B – 47 6.184 6.366 6.000 3.875 4.000 82FA-47
x 38 23-29
194A2 – 4.750 190-
47 x 38 192-47 47x38
194A2 – 47-53.5 8.379 8.681 8.319 190-
47 x 40 9 5/8 4.000 3.875 47x40
194A2 –
60 x 47 4.750 6.000 4.750 190-60 190-
194A4- 40-47 8.525 8.835 8.465 60X47
60 X47
194B-47 43.5- 8.535 8.755 8.375 4.000 4.750 3.875 192-47 190-
X40 53.5 47X40
194B-60 43.5- 8.435 8.755 8.275 4.750 6.000 4.750 190-60 190-
X 47 58.4 60X47
58
MODEL “BC-2RAH” SEAL BORE PACKER
____________________________________________________
BOTIL MODEL “BH” RETRIEVING
TOOL
Product No. BI 646-73
58-I
MODEL “PBR” RETRIEVABLE SEAL BORE PACKER
Features/Benefits
“PBR” PACKER
Product No. BI 509-08
Ÿ One trip installation.
Introduction Ÿ No tubing manipulation required. The setting mechanism is
The BOTIL “PBR” packer is a fully actuated hydraulically with pump pressure alone at any
retrievable, high performance depth, and The tubing can be displaced and the packer set
retainer production packer. after the well is flanged up.
Although originally designed for Ÿ Single, self-energizing cup-forming packing element for
premium gravel pack applications, repeated low and high differential reversals. Nitrile packing
it may also be used as standard elements are standard.
completion packer in high
Ÿ Bi-directional, case hardened slips are suitable for all grades
pressure and/or high temperature
of casing. The slips are protected by the slip cage during run-
wells where premium retrievable
in.
retainer production packer is
Ÿ Tubing may be run with Locator Tubing Seal Assembly pinned
required.
The Model “PBR” Packer is fully in PBR (Packer Bore Receptacle). PBR will be connected to
compatible with standard BOTIL Packer through Anchor Tubing Seal Nipple.
sealing accessories including Ÿ Packers may be run with BOTIL model KC-22 Anchor Tubing
retrievable and/or expandable Seal Nipple above the Packer.
plugs. Ÿ A left hand thread is provided in the body head of the packer.
This accepts standard packer accessories and also provides
The BOTIL Model “PBR” has the advantage over BOTIL Model a means of positioning the retrieving tool.
“BC-2RAH” Packer since it has benefit of a Shear Ring provided in Ÿ Packer is design for Straight Pull retrievable applications
the Body of the Packer enabling the Packer to be retrieved by Ÿ Short overall length facilitating easy running/retrieving
straight pull using a Retrieving Tool of short length. through doglegs and tight spots.
Ÿ Short length of Retrieving Tool required to retrieve the Packer
SPECIFICATION GUIDE
Size Casing Weight Preferred Range Gauge Lower Upper Min. Seal Retrieving
Size Range of Casing ID’s Ring Bore(in) Bore Bore Assembly Tool Size
( PPF) Min. Max. O.D(in Thru Seal Size
(in) (in) )
84A4 – 5.812 3.250 4.000 3.250 80DA40 80-40x32
40 x 32 29-35 5.879 6.189
84A4 – 7 5.820 3.875 81FA-47
47 x 38 OR OR 80-47x38
84B – 47 4.750 4.000 82FA-47
x 38 23-29 6.184 6.366 6.000 3.875
84B-40 x 4.000 3.250 80DA40 80-40X32
32
194A2 – 190-
47 x 38 192-47 47x38
194A2 – 47-53.5 8.379 8.681 8.319 4.750 190-
47 x 40 9 5/8 4.000 3.875 47x40
194A2 –
60 x 47 4.750 6.000 4.750 192-60 190-
194A4- 60X47
60 X47 40-47 8.525 8.835 8.465
194B-40 3.250 4.000 3.250 80DA40 80-40x32
x 32
194B-47 43.5-53.5 8.535 8.755 8.375 4.000 4.750 3.875 192-47 190-
X40 47X40
9 5/8 43.5-53.5 8.535 8.755 8.375 4.780 6.000 4.780 192-60 190-
194B- (4.750dri (4.750dr 60X47
60x47 ft) ift)
194B2- 9 5/8 47 – 58.4 8.435 8.681 8.275 4.750 6.000 4.750 192-60 190-
60 x 47 60x47
59
MODEL “PBR” RETRIEVABLE SEAL BORE PACKER
____________________________________________________
DESCRIPTION/APPLICATION
59.I
MODEL “PBR” RETRIEVABLE SEAL BORE PACKER
____________________________________________________
59.II