1 - Hydraulic Bollard Manual by BS 05052020 PDF
1 - Hydraulic Bollard Manual by BS 05052020 PDF
1 - Hydraulic Bollard Manual by BS 05052020 PDF
1
BS Hydraulic Bollard Manual
Safety
The hydraulic bollard you choose contains a wide range of mechanical and electronic
components, and any negligence in assembly or operation can threaten your safety.
Warm
Any individual or organization that sells or installs this product should assume the
corresponding safety responsibility, and also observe the following:
Any non-professionals cannot install, dismantle or maintain bollard. We will not take
any responsibility for any risk or danger.
This manual is for reference; subject to real product. Any revision may change without any
notice. We reserve the right of final explanation.
1
BS Hydraulic Bollard Manual
1 System Brief
1.1 Brief
Automatic hydraulic bollard is installed for entry/exit of lane of motor vehicles and any
place requiring access controlling.
2
BS Hydraulic Bollard Manual
1.2 Composition
Bollard: Blocking cars. 1 piece or several pieces are for selection based on your project.
Wire of bollard is corresponding to wire of slave board of cabinet.
Control system (cabinet):It receives signal and controls bollard raise and fall. It includes
main bollard, slave board and other electronic parts.
1.3 Feature.
Make car lane and pedestrian lane separately; distance of bollard is about 0.8-1.5 meters.
3
BS Hydraulic Bollard Manual
1.4 Model
H---hydraulic S---stainless steel 0---steel
2 Product brief
4
BS Hydraulic Bollard Manual
IP rate IP67
Working temperature -30~70℃ (low temperature: heating rod for selection)
L(Length)x W(width)x
material Number of bollard
H(height)
5
BS Hydraulic Bollard Manual
6
BS Hydraulic Bollard Manual
Main board
Terminal Port
function Description
number number
1 VIN-
2 VIN- DC24V power
M-P1 Power input
3 VIN+ input
4 VIN+
5 GND Ground
6 TL.R Red light
Notice: terminal for traffic light is
7 TL.G Green light
M-P2 closed. If needed, please inform
8 OC.COM Common
before placing the order.
9 OC.NC Normal open
10 OC.NO Normal closed
11 +12V 12Vpower
Power for Control module
12 GND output
13 UP.1
The 1st raise and
14 DOWN.1 Separated 2 groups of port input.
fall
15 GND Relay signal (push button, remote…)
16 UP.2 The 2nd raise ad is available.
M-P3
17 DOWN.2 fall
18 GND
Direction of detector is not limited;
19 PASS.1 Loop detector
20 PASS.2
21 INFRA When it works, raising signal is not
Infrared sensor
22 GND available, while falling signal is ok.
23 GND
Main board and slave board
M-P4 24 485- 485
communication
25 485+
Slave board
Terminal Port
function Description
number number
E-P1 1 VIN- DC24Vpower 24V
7
BS Hydraulic Bollard Manual
2 VIN- output
3 VIN+
4 VIN+
5 GND
E-P2 6 485- 485 RS485
7 485+
8 +24V
N/A
9 LED1
10 +24V
E-P3 LED Led and buzzer
11 LED2
12 +24V
Buzzer
13 BEEP
12V power
14 +12V
output
15 UP Up
16 DOWN Down
E-P4 17 Up-Limit Up limited External input port
18 Down-Limit Down limited
19 Press-Key Press key
20 SAFE Loop detector
21 GND ground
Rely 1; Normal
22 NC1
closed 1
Relay 1;
23 COM1 Connect to 24V power
Common1
relay1;normal
24 NO1
E-P5 open 1
Relay 2; normal Solenoid valve (bollard falls when
25 NC2
closed 2 power failure); another port for GND
Relay ; common
26 COM2 24V power supply
2
27 NO2 Relay 2; normal Solenoid valve (bollard keeps on the
8
BS Hydraulic Bollard Manual
① Station number of slave board should be started from 0001 and keep in a serial number
(it has set at our factory)
② The max power for main board/slave board about 15w.
Manual mode
Bollards raise and fall by remote/push button
(default)
Automatic
Work with loop detector; bollards raise automatically
mode
9
BS Hydraulic Bollard Manual
3 Installation
ATTN: your tube and pipe must be accordance with the standard of your country.
10
BS Hydraulic Bollard Manual
11
BS Hydraulic Bollard Manual
4 Additional
12
BS Hydraulic Bollard Manual
13
BS Hydraulic Bollard Manual
4.3 Maintenance
14
BS Hydraulic Bollard Manual
Moreover, if the following items are in the system, perform the following checks and
tests:
Test the flashlight that is incorporated in the element’s head for proper operation
Operating test of traffic-lights lanterns
Operating test of inductive safety turns
Check over the power failure procedure for proper operation
Operating test over the control radio receiver
Operating test of the emergency lowering sound analyzer
Operating test of the remote control GSM effector
15