3-PPSM Fuente de Poder Primaria 120V
3-PPSM Fuente de Poder Primaria 120V
3-PPSM Fuente de Poder Primaria 120V
Monitor
LIFE SAFETY & INCIDENT MANAGEMENT Module
EST3 Power
Supplies Power
S3000
3-BBC/M series
0186
APPROVED
Power supplies mount to the back of the chassis units or wall- • Automatic load testing of batteries
boxes. The associated power supply monitor module mounts on • Fully approved UL, ULC and EN standards (see Specifications
the local rail providing system power distribution and mounting section)
space for any control display module. Access to auxiliary power is
via easily accessible terminal blocks located on the power sup-
ply monitor module. Each power supply produces 7 Amps of
filtered and regulated power. With four power supplies located in
an enclosure (one primary and three booster power supplies) 28
amps of current is available for local rail modules, control display
modules and the eight auxiliary 3.5 amp power outputs (two per
supply).
L
Battery leads are electronically short circuit protected. If a short
R
occurs in the battery leads the charger automatically disables itself
and causes a trouble. The system will constantly look to see if
M
J9
the short has cleared. If the short clears the system automatically
J8
J11
J10
restores.
During operation on standby batteries, battery voltage is constant-
ly monitored. A trouble is reported if the battery voltage falls below
a specified value. J8
J9
J11
J10
J10
J9
J11
J9
J8
J11
Power
J10
Power Distribution
Module
PowerL
Supply (EN-54 only) SupplyR
M
J9
J8
J11
J10
Specifications
3-PPS/M & 3-PPS/M-230 & 3-PPS/M-230-E &
Catalog Number 3-BPS/M 3-BPS/M-230 3-BPS/M-230-E
3-BBC/M 3-BBC/M-230 3-BBC/M-230-E
Agency Approvals UL, ULC U L, ULC UL, ULC UL, ULC LPCB EN54*, CE EN54*
Input Voltage 120 Vac (+10%, -15%), 50-60 Hz 230 Vac (+10%, -15%), 50-60 Hz
Brownout Level < or = 102 Vac 96 Vac < or = 195 Vac 184 Vac < or = 195 Vac 188 Vac
3-PPS/M-230 3-PPS/M-230-E
3-PPS/M included
included with included with
with 3-CPU3 current
3-CPU3 current 3-CPU3 current
Current Alarm 50mA Alarm: 50 mA Alarm: 50 mA
Requirements 3-BBC/M Standby 50mA Standby: 50 mA Standby: 50 mA
3-BBC/M-230 3-BBC/M-230-E
Alarm: 70 mA
Alarm: 70 mA Alarm: 70 mA
Standby: 70 mA
Standby: 70 mA Standby: 70 mA
Input Current 3.0 A 1.5 A
Special Applications: 7.0 Amps
Total Output Current Regulated: 4.5 Amps total (including internal panel and auxiliary outputs).
Maximum regulated NAC power via 3-IDC8/4: 1 Amp (see note).
Battery Charging 65 AH Sealed 65 AH Sealed 30 AH Sealed
None None None
Capacity Lead-Acid Lead-Acid Lead-Acid
Low Battery Trouble 24 Vdc 22.5 Vdc
Deep Discharge
19.5 Vdc 20.0 Vdc
Cutoff
1 LRM Space +
Mounting 1 LRM space, 1 LRM space,
3-PPS: 2 footprints
Requirements 1 chassis footprint 1 chassis footprint
3-BBC: 1 footprint
Output Voltage 24 Vdc Nominal
Auxiliary Output
Two sources of 3.5 Amps each taken from total output current
Current
Auxiliary Output
18 AWG to 12 AWG (1 mm² to 2.5 mm²)
Terminal Capacity
Output Protection Electronic power limiting & heat sink temperature
Ground Fault
< 10K Ohms
Detection
Note: Each power supply can support 7 Amps with special application devices. Up to one regulated NAC circuit via 3-IDC8/4 can be supported per 3-PPS power supply. Total
power supply current available when supporting a regulated NAC is 4.5 Amps. Maximum regulated NAC current available from the 4.5A supply is 1 Amp.
* EN54-2: (1997) +A1: (2006) Control and Indicating Equipment; EN54-4: (1997) +A1: (2002) +A2: (2006) Power Supply Equipment; EN54-16:(2008) Voice Alarm Control and
Indicating Equipment
10-11-16