General Information: Torque Specifications
General Information: Torque Specifications
General Information: Torque Specifications
Shutdown
Previous Screen
Torque Specifications
Torque Specifications for All Caterpillar Products
Media Number -SENR3130-10 Publication Date -07/01/2005 Date Updated -07/28/2005
i02357647
General Information
SMCS - 7553
Introduction to Torque
"Torque" is measured in terms of force and distance. Force is the amount of pushing or pulling
applied at the end of the lever. Distance is the length of the lever that is being used. Torque values
are given in the following units: NEWTON meters (N·m), pound inches (lb in) and pound feet (lb ft)
This manual is intended to provide the operator with a reference. This manual will provide the
standard torque settings for the following: bolts, nuts, plugs, fittings and clamps.
Be sure to use a torque wrench that has the proper range. Torque wrenches must be used properly in
order to ensure that the correct torque is applied. Always use a smooth pull for torque wrenches. Do
not jerk a torque wrench. Do not use adapters that change the length of the torque wrench. For the
correct use of your torque wrench, refer to the instructions that were packaged with your torque
wrench. For more information on the correct use of torque wrenches, refer to Special Publication,
SEBV0516, "An Introduction to Torque".
Prior to installation of any hardware, ensure that components are in near new condition. Bolts and
threads must not be worn or damaged. Threads must not have burrs or nicks. Hardware must be free
of rust and corrosion. Clean reused fasteners with a noncorrosive cleaner. Lightly lubricate the
threads of reused fasteners. Lightly lubricate the mating surface of the head of reused fasteners.
Other applications for lubricating fasteners may also be specified in the Service Manual. The Service
Manual may also specify the use of sealants and compounds.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 17/07/2006
C-12 Truck Engine 1YN00001-UP(SEBP2692 - 16) - Document Structure Página 2 de 3
Note: Do not use sealants that are not specified in the Service Manual. Do not use compounds
that are not specified in the Service Manual. Clean old compound from the bolt and from the
hole before installation.
Torque-Turn
The torque-turn method is used when precise control over clamping force is required. There is an
initial torque and an additional turn. The initial torque is required to bring all parts of the joint into
contact. The additional turn provides the desired clamping force. Ensure that all fasteners have been
torqued before you perform the additional turns. Turn the fastener according to the specified amount.
The specified amount will normally be equal to or greater than 90°. The specified amount will
normally be in 30° increments. Turns of 120° or 180° are preferred. Turns of 120° or 180° are easily
measured by the points of the hex head of the fastener. Lubrication may be specified in order to
reduce the effort that is required for the final turn. The use of the torque-turn method will allow the
following:
z Track bolts
z Sprocket bolts
Note: Too much tension on the bolt will cause the bolt to be stretched beyond the point of yield. The
bolt will be permanently stretched. The bolt will loosen the grip on the parts that are being fastened.
If the bolt is tightened again, the bolt will break. Do not reuse bolts that have been permanently
stretched.
Torque Sequence
Unless the bolt tightening sequence is specified by the Service Manual, the fasteners should be
tightened in a cross pattern. Use Step 1 through Step 5 unless the tightening sequence is specified:
1. Hand tighten all fasteners. Larger fasteners may require the use of a small hand wrench.
4. Torque all fasteners to full torque by using a cross pattern. Large flanges may require
additional passes.
5. Apply at least one final full torque to all fasteners in a clockwise direction until all torque is
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 17/07/2006
C-12 Truck Engine 1YN00001-UP(SEBP2692 - 16) - Document Structure Página 3 de 3
Copyright 1993 - 2006 Caterpillar Inc. Mon Jul 17 17:23:31 CDT 2006
All Rights Reserved.
Private Network For SIS Licensees.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/s... 17/07/2006