Document Title: Datasheet for On-Off Valves / SDV / BDV

LTRO-1B Compressor Package Rental

CPGL Doc No.: ID-N-RW-JJ1-DSR-ST-87-3001

Originator: PT. KPM OIL AND GAS

CPGL Group Owner: UO | Project
Area: RW | Rawa
Location: ST | Station
System: 87 | Instrument System
GeneralDocument Type: DSR | Datasheet - Design Requirement
Discipline / Subdiscipline: J | Instrument / J1 | Field Instrument
Old CPGL Document No.: B-84572-RW-JJ1-DSR-ST-87-0001

Issued for Pasdon Yan Hendy R.

2 IFU 19-Mar-20 Putut. S Anhar Taufik U.
Use Harjuna Silvia Hidayat

TM Lead Unit
Sr. Project
Prepared Checked Approved Engineering
Reason for Engineer Owner
Rev Status Issue Date and Interface
Issue
Contractor Approvals Company Approvals

Printed initials in the approval boxes confirm that the document has been signed.
The originals are held within Document Management.
Datasheet for On-Off Valves / SDV / BDV ID-N-RW-JJ1-DSR-ST-87-3001_R2
LTRO-1B Compressor Package Rental Project
ConocoPhillips (Grissik). Ltd Page 2 of 21

Revision Sheet
ConocoPhillips (Grissik). Ltd

REVISION DATE DESCRIPTION OF CHANGE

2 19-Mar-20 Issued for Use

Additional Approvals

Name Title Signature Date

Datasheet for On-Off Valves / SDV / BDV ID-N-RW-JJ1-DSR-ST-87-3001_R2
LTRO-1B Compressor Package Rental Project
ConocoPhillips (Grissik) Ltd. Page 3 of 21

General Notes

1. Objective
This document is based on company standard specification and technical project requirements for the datasheet
On-Off, Shutdown & Blowdown Valves. This document is sample datasheet to be used as reference for Contractor to select
On-Off, Shutdown, Blowdown Valves and also preparing the datasheet.

2. General Requirement
2.1 Vendor shall be responsible for selection, supply, testing and supply of documentation of the On-Off, Shutdown & Blowdown
valves along with accessories as per attached data sheets and specification and shall be responsible
for the completion of the work to Company’s satisfaction.
2.2 Vendor shall submit drawings and data in accordance with the Vendor Data Requirement List (VDRL) and the data sheets.

3. On-Off, Shutdown and Blowdown valves requirement

3.1 Valves
3.1.1 All ball valves shall be designed as per API-6D.
3.1.2 The design, manufacturing, inspection and testing of ALL valves shall be in accordance with the following documents :
- ID-N-BU-LL0-STS-GN-00-0002 : Standard Specification Pipe Valves and Fitting
- ID-G-BU-JJ0-STS-GN-87-0001 : Standard Specification Instrument Design
- ID-N-BU-JJ1-STS-GN-00-0005 : Standard Specification Actuated Ball Valves
- ID-G-BU-DD3-STS-GN-98-0002 : Maintenance Coating Specification for Offshore and Onshore Facilities
3.1.3 All valves shall be fitted with suitable 'end of travel' stops at the fully open and fully closed positions and a local position indicator.
The design shall prevent the ingress of foreign material and corrosion products which would impair the operation of the stops.
3.1.4 All valves shall fail to the safe position on loss of electrical signal or loss of air supply. The safe failure positions
are specified in the data sheets.
3.1.5 Ball valves shall be solid type and be equipped with an anti static devices.
3.1.6 All ancillary equipment except for limit switches shall be mounted on a 1/8" 316 SS plate which shall be securely
bolted on the actuator. Devices such as restrictors and quick exhausts may be mounted inline. The vendor shall ensure that dissimilar
metals are adequately segregated to prevent galvanic corrosion.
3.1.7 Valves and ancillaries shall have permanently attached 316 SS tags with dimensions of 1" (L) x 2" (W) x 1/16" (T) as a minimum.
The tag plate shall bear the valve tag number, service, purchase order number, date of manufacture etc.
3.1.8 The field tags shall be attached with 16 AWG stainless steel wire or SS drive screws.
3.1.9 The Bolt and Nut material shall be in accordance with document no. ID-N-BU-LL0-STS-GN-00-0002
“Standard Specification Pipe, Valves and Fitting”.
3.1.10 Flange facing for RF flanges shall be smooth finish to 125 ~ 250 micro inches.
3.1.11 All ball valves shall be fitted with blow-out proof stems.
3.1.12 The material certification types and traceability levels shall be as per EN 10204, edition Certification for pressure containing parts
shall be as per EN 10204 type 3.1 and all other wetted parts to type 2.2.
3.1.13 The painting of the valves shall be in accordance with Doc. No. ID-G-BU-DD3-STS-GN-98-0002
“Maintenance Coating Specification for Offshore and Onshore Facilities”.
3.1.14 Supplier shall provide pressure and temperature charts for all seat and seal materials.
3.1.15 All valves shall be hydro-tested and leak tested in accordance with API 6D with low and high pressure gas testing.

3.2 Actuator
3.2.1 The design, manufacturing, inspection and testing of actuator shall be in accordance with the following document
ID-N-BU-JJ1-STS-GN-00-0005 “Standard Specification Actuated Ball Valves”.
3.2.2 The actuator shall normally be pneumatic spring return piston, single acting type complete with mounting kit.
3.2.3 The actuator assembly provided shall have stem travel indicator that clearly shows the valve position.
Datasheet for On-Off Valves / SDV / BDV ID-N-RW-JJ1-DSR-ST-87-3001_R2
LTRO-1B Compressor Package Rental Project
ConocoPhillips (Grissik) Ltd. Page 4 of 21

General Notes

3.2.4 The Instrument air supply for the actuators is 70 psig minimum, 100 psig normal and 135 psig design.
3.2.5 The actuator shall be sized 1.3 times the breakaway torque against max dP with 80 psig air supply.
3.2.6 -
3.2.7 Vendor shall provide the schematic drawing of partial stroke facility and its operating description.
3.2.8 Pneumatic tubing shall be material 316 SS used in conjunction with double ferrule 316 SS Swagelok compression fittings.
The tubing shall be 1/2" OD X 0.049" WT
3.2.9 Pneumatic connections shall be 1/2" NPTF.
3.2.10 Actuator shall be painted with color code in accordance with Doc. No. ID-G-BU-DD3-STS-GN-98-0002
“Maintenance Coating Specification for Offshore and Onshore Facilities”.
3.2.11 Actuator colour shall be RED (RAL3002) for fail to close, GREEN (RAL6002) for fail to open and GREY (RAL7000) for fail to last position.

3.3 Limit Switches

3.3.1 Limit switches shall be electrical proximity type, Explosion proof suitable for use in Class 1 Div 2 T4 Gr D.
3.3.2 The housing material shall be Aluminum Epoxy Coated as a minimum.
3.3.3 The switches shall be two SPDT gold plated type and the contact rating shall be 1A @ 24 VDC.
3.3.4 Screwed terminals shall be provided for cable termination and flying leads are not acceptable.
3.3.5 The cable entries shall be threaded, preferably ¾” NPTF for Limit Switch.
3.3.6 The offered model shall have anti corrosion sealed fully proven construction.
3.3.7 Enclosure shall be weather proof to IP 66 as a minimum.
3.3.8 The switches shall show the status of fully open and fully closed position of the valve.

3.4 Solenoid Valves

3.4.1 Solenoid valve(s) shall be Direct Acting 3-way, Universal.
3.4.2 Vendor to advise the Make and Model number.
3.4.3 Manual reset function shall be provided as indicated by the type of control schemes stated in datasheet.
3.4.4 The solenoid valve shall vent upon de-energization.
3.4.5 The solenoid valve shall be explosion proof EEx”d” suitable for use in Class 1 Div 2 T4 Gr D.
3.4.6 The housing material shall be 316 SS
3.4.7 The solenoid valve bodies shall be of 316 SS. Valve trim shall be 316 SS with FKM Viton-B with AED (Anti Explosive Decompression)
feature c/w it's certificate.
3.4.8 Screwed terminals shall be provided for cable termination and flying leads are not acceptable.
3.4.9 The cable entries shall be threaded, preferably ½” NPTF for Solenoid.
3.4.10 The solenoid valve shall be 24V DC powered, 3 watts maximum power consumption, complete with suppression diode.
3.4.11 The exhaust ports shall be fitted with stainless sintered metal bug screens to prevent ingress of dirt and foreign particles.
The pneumatic connection size for the solenoid valve shall be 1/2" NPTF.
3.4.12 Solenoid enclosure shall be weather proof to IP66 as a minimum.

3.5 Other Accessories

3.5.1 Air filter regulator material of construction shall be 316 SS. The pneumatic connection shall be 1/2" NPTF.
Vendor to advise the Make and Model number.
3.5.2 Quick exhaust valve material of construction shall be 316 SS. Vendor to advise The Make and Model number.
3.5.3 Material of construction for ancillaries such as relief valves, flow restrictors, etc shall be 316 SS.
Datasheet for On-Off Valves / SDV / BDV ID-N-RW-JJ1-DSR-ST-87-3001_R2
LTRO-1B Compressor Package Rental Project
ConocoPhillips (Grissik) Ltd. Page 5 of 21

List of SDV/BDV

No. Tag Number Instrument Type Sheet

1 20-SDV-0007 Shutdown Valve 6
2 20-SDV-0010 Shutdown Valve 7
3 20-BDV-0017 Blowdown valve 8
4 23-SDV-0103A Shutdown Valve 9
5 23-SDV-0106A Shutdown Valve 10
6 23-SDV-0103B Shutdown Valve 11
7 23-SDV-0106B Shutdown Valve 12
8 23-SDV-0103C Shutdown Valve 13
9 23-SDV-0106C Shutdown Valve 14
10 23-BDV-202A Blowdown valve 15
11 23-BDV-202B Blowdown valve 16
12 23-BDV-202C Blowdown valve 17
13 60-SDV-0001 Shutdown Valve 18
14 60-SDV-0102 Shutdown Valve 19
15 60-BDV-0002 Blowdown valve 20
16 Valve Arragement 21
 INSTRUMENT DATASHEET DOC. NO.:

ID-N-RW-JJ1-DSR-ST-87-3001
ON-OFF VALVES / SDV / BDV
Page : 6 of 21

PROJECT :
LTRO-1B LP COMPRESSOR PACKAGE RENTAL Issued for Use 2 19-Mar-20 PS ANR TU
PROJECT DESCRIPTION REV DATE BY CHK'D APPV'D
1 Tag No. 20-SDV-0007 51 Manufacturer Note 4
Inlet line from LTR LP Prod. Separator to
2 Service 52 Model Note 5
LP Prod. Separator
3 P & Id No. ID-N-RW-PP0-PID-ST-20-3001 53 Actuator Type Pneumatic Piston with Spring Return
4 GENERAL Line No. 8"-GP-20-0599-BA1 54 Acting Type Single Acting
5 Line Size / Wall Thickness / Pipe Id 8" 55 Spring Return Yes
6 Piping Class 300# - RF 56 Actuator Mechanism Scotch Yoke
7 Area Classification Class 1, Div 2, Group D 57 Operational Position Open
8 58 Air Failure Position Close
9 59 Air Supply Pressure Note 13
10 Process Fluid Hydrocarbon 60 Filter & Regulator Required 316SS
11 Fluid State Gas/Vapour 61 Lubricator & Pneumatic Conn. Required 1/2" NPTF
12 Operating Temp. °F 102.2 62 Max. Degree of Rotation 90 degree
13 Operating Press. Psig 200 - 275 63 Orientation Paralel to line
14 PROCESS Max. Inlet Press. Psig 350 64 Mechanical Position Indicator Red Close / Green Open
15 DATA Max. Shut Off DP Psi 350 65 Limit Stop Required
16 Design Press. Psig 350 66 ACTUATOR Overload Protection Required
17 Design Temp. °F 150 67 Break & Run Torque Note 5
18 Predicted Sound Level dB 85 (Note.5) 68 End Torque Note 5
19 69 Opening & Closing Time Note 14
20 Manufacturer Note 4 70 Adjustable Stroking Time Note 5
21 Model No. Note 5 71 Valve DP for Sizing 350 Psi
22 Design Code API 6D 72 Actuator Test Pressure Required
23 Piping Valve Spec BA-BA-3-2 73 Man. Override / Hand Wheel N/A
24 Valve Type Ball 74 Valve Control Station Set Required
25 Type Of Body Ball 3 Piece Body 75 Fire Safe N/A
26 Body Size Port Size 8" Full Bore 76 Paint & Finish Note 9, Red (RAL 3002)
27 Configuration Bonnet Trunnion Bolted 77 Air Consumption Note 5
28 Max. Degree Of Rotation 90 degree 78 Identification Plate Note 1
29 Fire Safe Design Yes API 6FA 79 IAS Operating Pressure 120 Psig
30 End Connection Size & Rating 8"-300#, RF 80 Tubing / Fitting Material 316SS
31 End Connection Type Flange RF (Note 8) 81 Partial Stroke Facility Yes (Local)
32 Body & Bonnet Material ASTM A105 82 Actuator Material Note 5
33 Ball / Disc Material ASTM A182 GR F316 83 Tag No. Open Position 20-ZSO-0007
34 Stem Material ASTM A276 F316 84 Tag No. Close Position 20-ZSC-0007
35 Seat Material ASTM A182 GR F316 85 Cable Entry Size 3/4" NPTF
SWITCHES
36 Seat Ring Material Note 5 86 Contact Config. / Rating SPDT, 24 VDC, 1 A
37 VALVE Seat Insert Material Filled TFE (Note 5) 87 Limit Switch Type 2ea Hermetically Sealed, Dry Contact
38 Seal Material Filled TFE (Note 5) 88
39 Packing Material Filled TFE 89 Tag No. 20-SOV-0007
ASTM A193 GR B7M Hot Dip Spun
40 Bonnet Bolts Material 90 Cable Entry Size 1/2" NPTF
Galvanized
ASTM A194 GR 2HM Hot Dip Spun
41 Bonnet Nuts Material 91 SOLENOID Solenoid Type / Material 3 Way Valve / 316 SS
Galvanized
Replaceable Ball & Seat, Anti Static VALVE
42 Ball & Seat Design Seat Ring, Side Entry, 92 Manual Reset Yes
Anti Blow Out Stem
43 Leakage Class Class VI ANSI FCI 70.2 93 Degree of Protection Explosion Proof Eex'd'
44 Break & Run Torque Note 5 94
45 Piggable N/A 95 Requisition Number Note 5
46 Fail Position Fail Close (FC) 96
47 Identification Plate Note 1 97
PURCHASE
48 Weight Note 5 98
49 Control Scheme Note 5 99
50 Block & Bleed N/A 100

NOTES :
1. Instruments shall have attached SS name plate which is hard stamped or engraved with tag number.
2. All exhaust port shall be provided with bug screen 316 SS.
3. The actuator shall be sized for 130% of the required valve reset/break torque at site maximum differential pressure as applicable.
4. As per COPI Pre-Approved Manufacturers-Fabricators List, ID-G-BU-GG0-AML-GN-00-0001 latest revision.
5. VTA = vendor to advise.
6. Valves shall be as per API 6D, fire tested as per API 6FA or API 607, and hydrotested as per API 598 or ISO 5208
7. All electronic components shall be explosion proof type suitable for area classification and certified by authorities body.
8. Flange facing & finish shall be as per ASME B16.5
9. Valve, actuator and accessories shall be painted as per Mfr Std, refer to Maintenance Coating Specification for Offshore and Onshore Facilities, ID-G-BU-DD3-STS-GN-98-0002.
10. Maximum sound level shall be 85 dBA at 3 feet distance from valve
11. All valves shall refer to COPI spec. Pipe, Valves and Fittings, ID-N-BU-LL0-STS-GN-00-0002 and all reference docs as indicated in General Notes.
12. Vendor shall submit torque table sizing to be checked and verified.
13. The instrument air pressure will have a normal pressure of 100 Psig. However actuators shall be capable of operating reliably with a supply pressure of 70 to 135 Psig.
14. Actuators shall be sized to allow closing stroking times not exceed 3 seconds plus 1 second for every 1" of valve body size.
15. Vendor shall test of hydrotest and gas test per code witness by purchaser, vendor shall provide enough notification of testing witnes
16. Vendor shall re-test (as test per code) periods valve all testing at indonesian testing facilities witnees by manufacturer prior deliverid to site
 INSTRUMENT DATASHEET DOC. NO.:

ID-N-RW-JJ1-DSR-ST-87-3001
ON-OFF VALVES / SDV / BDV
Page : 7 of 21

PROJECT :
LTRO-1B LP COMPRESSOR PACKAGE RENTAL Issued for Use 2 19-Mar-20 PS ANR TU
PROJECT DESCRIPTION REV DATE BY CHK'D APPV'D
1 Tag No. 20-SDV-0010 51 Manufacturer Note 4
Outlet line from LTR LP Prod. Separator to
2 Service 52 Model Note 5
MP Prod. Separator
3 P & Id No. ID-N-RW-PP0-PID-ST-20-3001
4"-PHL-20-0601-BA1 53 Actuator Type Pneumatic Piston with Spring Return
4 GENERAL Line No. 8"-GP-BA1-20-0599 54 Acting Type Single Acting
5 Line Size / Wall Thickness / Pipe Id 4" 55 Spring Return Yes
6 Piping Class 300# - RF 56 Actuator Mechanism Scotch Yoke
7 Area Classification Class 1, Div 2, Group D 57 Operational Position Open
8 58 Air Failure Position Close
9 59 Air Supply Pressure Note 13
10 Process Fluid Hydrocarbon 60 Filter & Regulator Required 316SS
11 Fluid State Liquid 61 Lubricator & Pneumatic Conn. Required 1/2" NPTF
12 Operating Temp. °F 102.2 62 Max. Degree of Rotation 90 degree
13 Operating Press. Psig 200 - 275 63 Orientation Paralel to line
14 PROCESS Max. Inlet Press. Psig 350 64 Mechanical Position Indicator Red Close / Green Open
15 DATA Max. Shut Off DP Psi 350 65 Limit Stop Required
16 Design Press. Psig 350 66 ACTUATOR Overload Protection Required
17 Design Temp. °F 150 67 Break & Run Torque Note 5
18 Predicted Sound Level dB 85 (Note.5) 68 End Torque Note 5
19 69 Opening & Closing Time Note 14
20 Manufacturer Note 4 70 Adjustable Stroking Time Note 5
21 Model No. Note 5 71 Valve DP for Sizing 350 Psi
22 Design Code API 6D 72 Actuator Test Pressure Required
23 Piping Valve Spec BA-BA-3-2 73 Man. Override / Hand Wheel N/A
24 Valve Type Ball 74 Valve Control Station Set Required
25 Type Of Body Ball 3 Piece Body 75 Fire Safe N/A
26 Body Size Port Size 4" Full Bore 76 Paint & Finish Note 9, Red (RAL 3002)
27 Configuration Bonnet Trunnion Bolted 77 Air Consumption Note 5
28 Max. Degree Of Rotation 90 degree 78 Identification Plate Note 1
29 Fire Safe Design Yes API 6FA 79 IAS Operating Pressure 120 Psig
30 End Connection Size & Rating 4"-300#, RF 80 Tubing / Fitting Material 316SS
31 End Connection Type Flange RF (Note 8) 81 Partial Stroke Facility Yes (Local)
32 Body & Bonnet Material ASTM A105 82 Actuator Material Note 5
33 Ball / Disc Material ASTM A182 GR F316 83 Tag No. Open Position 20-ZSO-0007
34 Stem Material ASTM A276 F316 84 Tag No. Close Position 20-ZSC-0007
35 Seat Material ASTM A182 GR F316 85 Cable Entry Size 3/4" NPTF
SWITCHES
36 Seat Ring Material Note 5 86 Contact Config. / Rating SPDT, 24 VDC, 1 A
37 VALVE Seat Insert Material Filled TFE (Note 5) 87 Limit Switch Type 2ea Hermetically Sealed, Dry Contact
38 Seal Material Filled TFE (Note 5) 88
39 Packing Material Filled TFE 89 Tag No. 20-SOV-0007
ASTM A193 GR B7M Hot Dip Spun
40 Bonnet Bolts Material 90 Cable Entry Size 1/2" NPTF
Galvanized
ASTM A194 GR 2HM Hot Dip Spun
41 Bonnet Nuts Material 91 SOLENOID Solenoid Type / Material 3 Way Valve / 316 SS
Galvanized
Replaceable Ball & Seat, Anti Static VALVE
42 Ball & Seat Design Seat Ring, Side Entry, 92 Manual Reset Yes
Anti Blow Out Stem
43 Leakage Class Class VI ANSI FCI 70.2 93 Degree of Protection Explosion Proof Eex'd'
44 Break & Run Torque Note 5 94
45 Piggable N/A 95 Requisition Number Note 5
46 Fail Position Fail Close (FC) 96
47 Identification Plate Note 1 97
PURCHASE
48 Weight Note 5 98
49 Control Scheme Note 5 99
50 Block & Bleed N/A 100

NOTES :
1. Instruments shall have attached SS name plate which is hard stamped or engraved with tag number.
2. All exhaust port shall be provided with bug screen 316 SS.
3. The actuator shall be sized for 130% of the required valve reset/break torque at site maximum differential pressure as applicable.
4. As per COPI Pre-Approved Manufacturers-Fabricators List, ID-G-BU-GG0-AML-GN-00-0001 latest revision.
5. VTA = vendor to advise.
6. Valves shall be as per API 6D, fire tested as per API 6FA or API 607, and hydrotested as per API 598 or ISO 5208
7. All electronic components shall be explosion proof type suitable for area classification and certified by authorities body.
8. Flange facing & finish shall be as per ASME B16.5
9. Valve, actuator and accessories shall be painted as per Mfr Std, refer to Maintenance Coating Specification for Offshore and Onshore Facilities, ID-G-BU-DD3-STS-GN-98-0002.
10. Maximum sound level shall be 85 dBA at 3 feet distance from valve
11. All valves shall refer to COPI spec. Pipe, Valves and Fittings, ID-N-BU-LL0-STS-GN-00-0002 and all reference docs as indicated in General Notes.
12. Vendor shall submit torque table sizing to be checked and verified.
13. The instrument air pressure will have a normal pressure of 100 Psig. However actuators shall be capable of operating reliably with a supply pressure of 70 to 135 Psig.
14. Actuators shall be sized to allow closing stroking times not exceed 3 seconds plus 1 second for every 1" of valve body size.
15. Vendor shall test of hydrotest and gas test per code witness by purchaser, vendor shall provide enough notification of testing witnes
16. Vendor shall re-test (as test per code) periods valve all testing at indonesian testing facilities witnees by manufacturer prior deliverid to site
 INSTRUMENT DATASHEET DOC. NO.:

ID-N-RW-JJ1-DSR-ST-87-3001
ON-OFF VALVES / SDV / BDV
Page : 8 of 21

PROJECT :
LTRO-1B LP COMPRESSOR PACKAGE RENTAL Issued for Use 2 19-Mar-20 PS ANR TU
PROJECT DESCRIPTION REV DATE BY CHK'D APPV'D

1 Tag No. 20-BDV-0017 51 Manufacturer Note 4

Outlet line from LTR LP Prod. Separator to
2 Service 52 Model Note 5
Flare Headaer
3 P & Id No. ID-N-RW-PP0-PID-ST-20-3001 53 Actuator Type Pneumatic Piston with Spring Return
4 GENERAL Line No. 2"-GP-20-0605-BA1 54 Acting Type Single Acting
5 Line Size / Wall Thickness / Pipe Id 2" 55 Spring Return Yes
6 Piping Class 300# - RF 56 Actuator Mechanism Scotch Yoke
7 Area Classification Class 1, Div 2, Group D 57 Operational Position Close
8 58 Air Failure Position Open
9 59 Air Supply Pressure Note 13
10 Process Fluid Hydrocarbon 60 Filter & Regulator Required 316SS
11 Fluid State Gas 61 Lubricator & Pneumatic Conn. Required 1/2" NPTF
12 Operating Temp. °F 102.2 62 Max. Degree of Rotation 90 degree
13 Operating Press. Psig 200 -275 63 Orientation Paralel to line
14 PROCESS Max. Inlet Press. Psig 350 64 Mechanical Position Indicator Red Close / Green Open
15 DATA Max. Shut Off DP Psi 350 65 Limit Stop Required
16 Design Press. Psig 350 66 ACTUATOR Overload Protection Required
17 Design Temp. °F 150 67 Break & Run Torque Note 5
18 Predicted Sound Level dB 85 (Note.5) 68 End Torque Note 5
19 69 Opening & Closing Time Note 14
20 Manufacturer Note 4 70 Adjustable Stroking Time Note 5
21 Model No. Note 5 71 Valve DP for Sizing 350 Psi
22 Design Code API 6D 72 Actuator Test Pressure Required
23 Piping Valve Spec BA-BA-3-2 73 Man. Override / Hand Wheel N/A
24 Valve Type Ball 74 Valve Control Station Set Required
25 Type Of Body Ball 3 Piece Body 75 Fire Safe N/A
26 Body Size Port Size 2" Full Bore 76 Paint & Finish Note 9, Red (RAL 3002)
27 Configuration Bonnet Trunnion Bolted 77 Air Consumption Note 5
28 Max. Degree Of Rotation 90 degree 78 Identification Plate Note 1
29 Fire Safe Design Yes API 6FA 79 IAS Operating Pressure 120 Psig
30 End Connection Size & Rating 2"-300#, RF 80 Tubing / Fitting Material 316SS
31 End Connection Type Flange RF (Note 8) 81 Partial Stroke Facility Yes (Local)
32 Body & Bonnet Material ASTM A105 82 Actuator Material Note 5
33 Ball / Disc Material ASTM A182 GR F316 83 Tag No. Open Position 20-ZSO-0017
34 Stem Material ASTM A276 F316 84 Tag No. Close Position 20-ZSC-0017
35 Seat Material ASTM A182 GR F316 85 Cable Entry Size 3/4" NPTF
SWITCHES
36 Seat Ring Material Note 5 86 Contact Config. / Rating SPDT, 24 VDC, 1 A
37 VALVE Seat Insert Material Filled TFE (Note 5) 87 Limit Switch Type 2ea Hermetically Sealed, Dry Contact
38 Seal Material Filled TFE (Note 5) 88
39 Packing Material Filled TFE 89 Tag No. 20-SOV-0017
ASTM A193 GR B7M Hot Dip Spun
40 Bonnet Bolts Material 90 Cable Entry Size 1/2" NPTF
Galvanized
ASTM A194 GR 2HM Hot Dip Spun
41 Bonnet Nuts Material 91 SOLENOID Solenoid Type / Material 3 Way Valve / 316 SS
Galvanized
Replaceable Ball & Seat, Anti Static VALVE
42 Ball & Seat Design Seat Ring, Side Entry, 92 Manual Reset Yes
Anti Blow Out Stem
43 Leakage Class Class VI ANSI FCI 70.2 93 Degree of Protection Explosion Proof Eex'd'
44 Break & Run Torque Note 5 94
45 Piggable N/A 95 Requisition Number Note 5
46 Fail Position Fail Open (FO) 96
47 Identification Plate Note 1 97
PURCHASE
48 Weight Note 5 98
49 Control Scheme Note 5 99
50 Block & Bleed N/A 100

NOTES :
1. Instruments shall have attached SS name plate which is hard stamped or engraved with tag number.
2. All exhaust port shall be provided with bug screen 316 SS.
3. The actuator shall be sized for 130% of the required valve reset/break torque at site maximum differential pressure as applicable.
4. As per COPI Pre-Approved Manufacturers-Fabricators List, ID-G-BU-GG0-AML-GN-00-0001 latest revision.
5. VTA = vendor to advise.
6. Valves shall be as per API 6D, fire tested as per API 6FA or API 607, and hydrotested as per API 598 or ISO 5208
7. All electronic components shall be explosion proof type suitable for area classification and certified by authorities body.
8. Flange facing & finish shall be as per ASME B16.5
9. Valve, actuator and accessories shall be painted as per Mfr Std, refer to Maintenance Coating Specification for Offshore and Onshore Facilities, ID-G-BU-DD3-STS-GN-98-0002.
10. Maximum sound level shall be 85 dBA at 3 feet distance from valve
11. All valves shall refer to COPI spec. Pipe, Valves and Fittings, ID-N-BU-LL0-STS-GN-00-0002 and all reference docs as indicated in General Notes.
12. Vendor shall submit torque table sizing to be checked and verified.
13. The instrument air pressure will have a normal pressure of 100 Psig. However actuators shall be capable of operating reliably with a supply pressure of 70 to 135 Psig.
14. Actuators shall be sized to allow closing stroking times not exceed 3 seconds plus 1 second for every 1" of valve body size.
15. Vendor shall test of hydrotest and gas test per code witness by purchaser, vendor shall provide enough notification of testing witnes
16. Vendor shall re-test (as test per code) periods valve all testing at indonesian testing facilities witnees by manufacturer prior deliverid to site
 INSTRUMENT DATASHEET DOC. NO.:

ID-N-RW-JJ1-DSR-ST-87-3001
ON-OFF VALVES / SDV / BDV
Page : 9 of 21

PROJECT :
LTRO-1B LP COMPRESSOR PACKAGE RENTAL Issued for Use 2 19-Mar-20 PS ANR TU
PROJECT DESCRIPTION REV DATE BY CHK'D APPV'D
1 Tag No. 23-SDV-0103A 51 Manufacturer Note 4

2 Service Inlet LTR LP Compressor Package-A 52 Model Note 5

3 P & Id No. ID-N-RW-PP0-PID-ST-23-3001 53 Actuator Type Pneumatic Piston with Spring Return
4 GENERAL Line No. 10"-GP-23-0615-BA1 54 Acting Type Single Acting
5 Line Size / Wall Thickness / Pipe Id 10" 55 Spring Return Yes
6 Piping Class 300# - RF 56 Actuator Mechanism Scotch Yoke
7 Area Classification Class 1, Div 2, Group D 57 Operational Position Open
8 58 Air Failure Position Close
9 59 Air Supply Pressure Note 13
10 Process Fluid Hydrocarbon 60 Filter & Regulator Required 316SS
11 Fluid State Gas/Vapour 61 Lubricator & Pneumatic Conn. Required 1/2" NPTF
12 Operating Temp. °F 102.2 62 Max. Degree of Rotation 90 degree
13 Operating Press. Psig 200 -275 63 Orientation Paralel to line
14 PROCESS Max. Inlet Press. Psig 350 64 Mechanical Position Indicator Red Close / Green Open
15 DATA Max. Shut Off DP Psi 350 65 Limit Stop Required
16 Design Press. Psig 350 66 ACTUATOR Overload Protection Required
17 Design Temp. °F 150 67 Break & Run Torque Note 5
18 Predicted Sound Level dB 85 (Note.5) 68 End Torque Note 5
19 69 Opening & Closing Time Note 14
20 Manufacturer Note 4 70 Adjustable Stroking Time Note 5
21 Model No. Note 5 71 Valve DP for Sizing 350 Psi
22 Design Code API 6D 72 Actuator Test Pressure Required
23 Piping Valve Spec BA-BA-3-2 73 Man. Override / Hand Wheel N/A
24 Valve Type Ball 74 Valve Control Station Set Required
25 Type Of Body Ball 3 Piece Body 75 Fire Safe N/A
26 Body Size Port Size 10" Full Bore 76 Paint & Finish Note 9, Red (RAL 3002)
27 Configuration Bonnet Trunnion Bolted 77 Air Consumption Note 5
28 Max. Degree Of Rotation 90 degree 78 Identification Plate Note 1
29 Fire Safe Design Yes API 6FA 79 IAS Operating Pressure 120 Psig
30 End Connection Size & Rating 10"-300#, RF 80 Tubing / Fitting Material 316SS
31 End Connection Type Flange RF (Note 8) 81 Partial Stroke Facility No (Note. 17)
32 Body & Bonnet Material ASTM A105 82 Actuator Material Note 5
33 Ball / Disc Material ASTM A182 GR F316 83 Tag No. Open Position 23-ZSO-0103A
34 Stem Material ASTM A276 F316 84 Tag No. Close Position 23-ZSC-0103A
35 Seat Material ASTM A182 GR F316 85 Cable Entry Size 3/4" NPTF
SWITCHES
36 Seat Ring Material Note 5 86 Contact Config. / Rating SPDT, 24 VDC, 1 A
37 VALVE Seat Insert Material Filled TFE (Note 5) 87 Limit Switch Type 2ea Hermetically Sealed, Dry Contact
38 Seal Material Filled TFE (Note 5) 88
39 Packing Material Filled TFE 89 Tag No. 23-SOV-0103A
ASTM A193 GR B7M Hot Dip Spun
40 Bonnet Bolts Material 90 Cable Entry Size 1/2" NPTF
Galvanized
ASTM A194 GR 2HM Hot Dip Spun
41 Bonnet Nuts Material 91 SOLENOID Solenoid Type / Material 3 Way Valve / 316 SS
Galvanized
Replaceable Ball & Seat, Anti Static VALVE
42 Ball & Seat Design Seat Ring, Side Entry, 92 Manual Reset Yes
Anti Blow Out Stem
43 Leakage Class Class VI ANSI FCI 70.2 93 Degree of Protection Explosion Proof Eex'd'
44 Break & Run Torque Note 5 94
45 Piggable N/A 95 Requisition Number Note 5
46 Fail Position Fail Close (FC) 96
47 Identification Plate Note 1 97
PURCHASE
48 Weight Note 5 98
49 Control Scheme Note 5 99
50 Block & Bleed N/A 100

NOTES :
1. Instruments shall have attached SS name plate which is hard stamped or engraved with tag number.
2. All exhaust port shall be provided with bug screen 316 SS.
3. The actuator shall be sized for 130% of the required valve reset/break torque at site maximum differential pressure as applicable.
4. As per COPI Pre-Approved Manufacturers-Fabricators List, ID-G-BU-GG0-AML-GN-00-0001 latest revision.
5. VTA = vendor to advise.
6. Valves shall be as per API 6D, fire tested as per API 6FA or API 607, and hydrotested as per API 598 or ISO 5208
7. All electronic components shall be explosion proof type suitable for area classification and certified by authorities body.
8. Flange facing & finish shall be as per ASME B16.5
9. Valve, actuator and accessories shall be painted as per Mfr Std, refer to Maintenance Coating Specification for Offshore and Onshore Facilities, ID-G-BU-DD3-STS-GN-98-0002.
10. Maximum sound level shall be 85 dBA at 3 feet distance from valve
11. All valves shall refer to COPI spec. Pipe, Valves and Fittings, ID-N-BU-LL0-STS-GN-00-0002 and all reference docs as indicated in General Notes.
12. Vendor shall submit torque table sizing to be checked and verified.
13. The instrument air pressure will have a normal pressure of 100 Psig. However actuators shall be capable of operating reliably with a supply pressure of 70 to 135 Psig.
14. Actuators shall be sized to allow closing stroking times not exceed 3 seconds plus 1 second for every 1" of valve body size.
15. Vendor shall test of hydrotest and gas test per code witness by purchaser, vendor shall provide enough notification of testing witnes
16. Vendor shall re-test (as test per code) periods valve all testing at indonesian testing facilities witnees by manufacturer prior deliverid to site
17. Stroke test will do periodically in the same time during unit gas compressor preventive maintenance schedulewithin 1500 Run-hours or 2 month activate from
from UCP in manual mode
 INSTRUMENT DATASHEET DOC. NO.:

ID-N-RW-JJ1-DSR-ST-87-3001
ON-OFF VALVES / SDV / BDV
Page : 10 of 21

PROJECT :
LTRO-1B LP COMPRESSOR PACKAGE RENTAL Issued for Use 2 19-Mar-20 PS ANR TU
PROJECT DESCRIPTION REV DATE BY CHK'D APPV'D
1 Tag No. 23-SDV-0106A 51 Manufacturer Note 4

2 Service Outlet LTR LP Compressor Package-A 52 Model Note 5

3 P & Id No. ID-N-RW-PP0-PID-ST-23-3001 53 Actuator Type Pneumatic Piston with Spring Return
4 GENERAL Line No. 8"-GP-23-0619-BA1 54 Acting Type Single Acting
5 Line Size / Wall Thickness / Pipe Id 8" 55 Spring Return Yes
6 Piping Class 300# - RF 56 Actuator Mechanism Scotch Yoke
7 Area Classification Class 1, Div 2, Group D 57 Operational Position Open
8 58 Air Failure Position Close
9 59 Air Supply Pressure Note 13
10 Process Fluid Hydrocarbon 60 Filter & Regulator Required 316SS
11 Fluid State Gas/Vapour 61 Lubricator & Pneumatic Conn. Required 1/2" NPTF
12 Operating Temp. °F 120 62 Max. Degree of Rotation 90 degree
13 Operating Press. Psig 510 63 Orientation Paralel to line
14 PROCESS Max. Inlet Press. Psig 600 64 Mechanical Position Indicator Red Close / Green Open
15 DATA Max. Shut Off DP Psi 600 65 Limit Stop Required
16 Design Press. Psig 600 66 ACTUATOR Overload Protection Required
17 Design Temp. °F 150 67 Break & Run Torque Note 5
18 Predicted Sound Level dB 85 (Note.5) 68 End Torque Note 5
19 69 Opening & Closing Time Note 14
20 Manufacturer Note 4 70 Adjustable Stroking Time Note 5
21 Model No. Note 5 71 Valve DP for Sizing 600 Psi
22 Design Code API 6D 72 Actuator Test Pressure Required
23 Piping Valve Spec BA-BA-3-2 73 Man. Override / Hand Wheel N/A
24 Valve Type Ball 74 Valve Control Station Set Required
25 Type Of Body Ball 3 Piece Body 75 Fire Safe N/A
26 Body Size Port Size 8" Full Bore 76 Paint & Finish Note 9, Red (RAL 3002)
27 Configuration Bonnet Trunnion Bolted 77 Air Consumption Note 5
28 Max. Degree Of Rotation 90 degree 78 Identification Plate Note 1
29 Fire Safe Design Yes API 6FA 79 IAS Operating Pressure 120 Psig
30 End Connection Size & Rating 8"-300#, RF 80 Tubing / Fitting Material 316SS
31 End Connection Type Flange RF (Note 8) 81 Partial Stroke Facility No (Note. 17)
32 Body & Bonnet Material ASTM A105 82 Actuator Material Note 5
33 Ball / Disc Material ASTM A182 GR F316 83 Tag No. Open Position 23-ZSO-0106A
34 Stem Material ASTM A276 F316 84 Tag No. Close Position 23-ZSC-0106A
35 Seat Material ASTM A182 GR F316 85 Cable Entry Size 3/4" NPTF
SWITCHES
36 Seat Ring Material Note 5 86 Contact Config. / Rating SPDT, 24 VDC, 1 A
37 VALVE Seat Insert Material Filled TFE (Note 5) 87 Limit Switch Type 2ea Hermetically Sealed, Dry Contact
38 Seal Material Filled TFE (Note 5) 88
39 Packing Material Filled TFE 89 Tag No. 23-SOV-0106A
ASTM A193 GR B7M Hot Dip Spun
40 Bonnet Bolts Material 90 Cable Entry Size 1/2" NPTF
Galvanized
ASTM A194 GR 2HM Hot Dip Spun
41 Bonnet Nuts Material 91 SOLENOID Solenoid Type / Material 3 Way Valve / 316 SS
Galvanized
Replaceable Ball & Seat, Anti Static VALVE
42 Ball & Seat Design Seat Ring, Side Entry, 92 Manual Reset Yes
Anti Blow Out Stem
43 Leakage Class Class VI ANSI FCI 70.2 93 Degree of Protection Explosion Proof Eex'd'
44 Break & Run Torque Note 5 94
45 Piggable N/A 95 Requisition Number Note 5
46 Fail Position Fail Close (FC) 96
47 Identification Plate Note 1 97
PURCHASE
48 Weight Note 5 98
49 Control Scheme Note 5 99
50 Block & Bleed N/A 100

NOTES :
1. Instruments shall have attached SS name plate which is hard stamped or engraved with tag number.
2. All exhaust port shall be provided with bug screen 316 SS.
3. The actuator shall be sized for 130% of the required valve reset/break torque at site maximum differential pressure as applicable.
4. As per COPI Pre-Approved Manufacturers-Fabricators List, ID-G-BU-GG0-AML-GN-00-0001 latest revision.
5. VTA = vendor to advise.
6. Valves shall be as per API 6D, fire tested as per API 6FA or API 607, and hydrotested as per API 598 or ISO 5208
7. All electronic components shall be explosion proof type suitable for area classification and certified by authorities body.
8. Flange facing & finish shall be as per ASME B16.5
9. Valve, actuator and accessories shall be painted as per Mfr Std, refer to Maintenance Coating Specification for Offshore and Onshore Facilities, ID-G-BU-DD3-STS-GN-98-0002.
10. Maximum sound level shall be 85 dBA at 3 feet distance from valve
11. All valves shall refer to COPI spec. Pipe, Valves and Fittings, ID-N-BU-LL0-STS-GN-00-0002 and all reference docs as indicated in General Notes.
12. Vendor shall submit torque table sizing to be checked and verified.
13. The instrument air pressure will have a normal pressure of 100 Psig. However actuators shall be capable of operating reliably with a supply pressure of 70 to 135 Psig.
14. Actuators shall be sized to allow closing stroking times not exceed 3 seconds plus 1 second for every 1" of valve body size.
15. Vendor shall test of hydrotest and gas test per code witness by purchaser, vendor shall provide enough notification of testing witnes
16. Vendor shall re-test (as test per code) periods valve all testing at indonesian testing facilities witnees by manufacturer prior deliverid to site
17. Stroke test will do periodically in the same time during unit gas compressor preventive maintenance schedulewithin 1500 Run-hours or 2 month activate from
from UCP in manual mode
 INSTRUMENT DATASHEET DOC. NO.:

ID-N-RW-JJ1-DSR-ST-87-3001
ON-OFF VALVES / SDV / BDV
Page : 11 of 21

PROJECT :
LTRO-1B LP COMPRESSOR PACKAGE RENTAL Issued for Use 2 19-Mar-20 PS ANR TU
PROJECT DESCRIPTION REV DATE BY CHK'D APPV'D
1 Tag No. 23-SDV-0103B 51 Manufacturer Note 4

2 Service Inlet LTR LP Compressor Package-B 52 Model Note 5

3 P & Id No. ID-N-RW-PP0-PID-ST-23-3004 53 Actuator Type Pneumatic Piston with Spring Return
4 GENERAL Line No. 10"-GP-23-0616-BA1 54 Acting Type Single Acting
5 Line Size / Wall Thickness / Pipe Id 10" 55 Spring Return Yes
6 Piping Class 300# - RF 56 Actuator Mechanism Scotch Yoke
7 Area Classification Class 1, Div 2, Group D 57 Operational Position Open
8 58 Air Failure Position Close
9 59 Air Supply Pressure Note 13
10 Process Fluid Hydrocarbon 60 Filter & Regulator Required 316SS
11 Fluid State Gas/Vapour 61 Lubricator & Pneumatic Conn. Required 1/2" NPTF
12 Operating Temp. °F 102.2 62 Max. Degree of Rotation 90 degree
13 Operating Press. Psig 200 -275 63 Orientation Paralel to line
14 PROCESS Max. Inlet Press. Psig 350 64 Mechanical Position Indicator Red Close / Green Open
15 DATA Max. Shut Off DP Psi 350 65 Limit Stop Required
16 Design Press. Psig 350 66 ACTUATOR Overload Protection Required
17 Design Temp. °F 150 67 Break & Run Torque Note 5
18 Predicted Sound Level dB 85 (Note.5) 68 End Torque Note 5
19 69 Opening & Closing Time Note 14
20 Manufacturer Note 4 70 Adjustable Stroking Time Note 5
21 Model No. Note 5 71 Valve DP for Sizing 350 Psi
22 Design Code API 6D 72 Actuator Test Pressure Required
23 Piping Valve Spec BA-BA-3-2 73 Man. Override / Hand Wheel N/A
24 Valve Type Ball 74 Valve Control Station Set Required
25 Type Of Body Ball 3 Piece Body 75 Fire Safe N/A
26 Body Size Port Size 10" Full Bore 76 Paint & Finish Note 9, Red (RAL 3002)
27 Configuration Bonnet Trunnion Bolted 77 Air Consumption Note 5
28 Max. Degree Of Rotation 90 degree 78 Identification Plate Note 1
29 Fire Safe Design Yes API 6FA 79 IAS Operating Pressure 120 Psig
30 End Connection Size & Rating 10"-300#, RF 80 Tubing / Fitting Material 316SS
31 End Connection Type Flange RF (Note 8) 81 Partial Stroke Facility No (Note. 17)
32 Body & Bonnet Material ASTM A105 82 Actuator Material Note 5
33 Ball / Disc Material ASTM A182 GR F316 83 Tag No. Open Position 23-ZSO-0103B
34 Stem Material ASTM A276 F316 84 Tag No. Close Position 23-ZSC-0103B
35 Seat Material ASTM A182 GR F316 85 Cable Entry Size 3/4" NPTF
SWITCHES
36 Seat Ring Material Note 5 86 Contact Config. / Rating SPDT, 24 VDC, 1 A
37 VALVE Seat Insert Material Filled TFE (Note 5) 87 Limit Switch Type 2ea Hermetically Sealed, Dry Contact
38 Seal Material Filled TFE (Note 5) 88
39 Packing Material Filled TFE 89 Tag No. 23-SOV-0103B
ASTM A193 GR B7M Hot Dip Spun
40 Bonnet Bolts Material 90 Cable Entry Size 1/2" NPTF
Galvanized
ASTM A194 GR 2HM Hot Dip Spun
41 Bonnet Nuts Material 91 SOLENOID Solenoid Type / Material 3 Way Valve / 316 SS
Galvanized
Replaceable Ball & Seat, Anti Static VALVE
42 Ball & Seat Design Seat Ring, Side Entry, 92 Manual Reset Yes
Anti Blow Out Stem
43 Leakage Class Class VI ANSI FCI 70.2 93 Degree of Protection Explosion Proof Eex'd'
44 Break & Run Torque Note 5 94
45 Piggable N/A 95 Requisition Number Note 5
46 Fail Position Fail Close (FC) 96
47 Identification Plate Note 1 97
PURCHASE
48 Weight Note 5 98
49 Control Scheme Note 5 99
50 Block & Bleed N/A 100

NOTES :
1. Instruments shall have attached SS name plate which is hard stamped or engraved with tag number.
2. All exhaust port shall be provided with bug screen 316 SS.
3. The actuator shall be sized for 130% of the required valve reset/break torque at site maximum differential pressure as applicable.
4. As per COPI Pre-Approved Manufacturers-Fabricators List, ID-G-BU-GG0-AML-GN-00-0001 latest revision.
5. VTA = vendor to advise.
6. Valves shall be as per API 6D, fire tested as per API 6FA or API 607, and hydrotested as per API 598 or ISO 5208
7. All electronic components shall be explosion proof type suitable for area classification and certified by authorities body.
8. Flange facing & finish shall be as per ASME B16.5
9. Valve, actuator and accessories shall be painted as per Mfr Std, refer to Maintenance Coating Specification for Offshore and Onshore Facilities, ID-G-BU-DD3-STS-GN-98-0002.
10. Maximum sound level shall be 85 dBA at 3 feet distance from valve
11. All valves shall refer to COPI spec. Pipe, Valves and Fittings, ID-N-BU-LL0-STS-GN-00-0002 and all reference docs as indicated in General Notes.
12. Vendor shall submit torque table sizing to be checked and verified.
13. The instrument air pressure will have a normal pressure of 100 Psig. However actuators shall be capable of operating reliably with a supply pressure of 70 to 135 Psig.
14. Actuators shall be sized to allow closing stroking times not exceed 3 seconds plus 1 second for every 1" of valve body size.
15. Vendor shall test of hydrotest and gas test per code witness by purchaser, vendor shall provide enough notification of testing witnes
16. Vendor shall re-test (as test per code) periods valve all testing at indonesian testing facilities witnees by manufacturer prior deliverid to site
17. Stroke test will do periodically in the same time during unit gas compressor preventive maintenance schedulewithin 1500 Run-hours or 2 month activate from
from UCP in manual mode
 INSTRUMENT DATASHEET DOC. NO.:

ID-N-RW-JJ1-DSR-ST-87-3001
ON-OFF VALVES / SDV / BDV
Page : 12 of 21

PROJECT :
LTRO-1B LP COMPRESSOR PACKAGE RENTAL Issued for Use 2 19-Mar-20 PS ANR TU
PROJECT DESCRIPTION REV DATE BY CHK'D APPV'D
1 Tag No. 23-SDV-0106B 51 Manufacturer Note 4

2 Service Outlet LTR LP Compressor Package-B 52 Model Note 5

3 P & Id No. ID-N-RW-PP0-PID-ST-23-3004 53 Actuator Type Pneumatic Piston with Spring Return
4 GENERAL Line No. 8"-GP-23-0626-BA1 54 Acting Type Single Acting
5 Line Size / Wall Thickness / Pipe Id 8" 55 Spring Return Yes
6 Piping Class 300# - RF 56 Actuator Mechanism Scotch Yoke
7 Area Classification Class 1, Div 2, Group D 57 Operational Position Open
8 58 Air Failure Position Close
9 59 Air Supply Pressure Note 13
10 Process Fluid Hydrocarbon 60 Filter & Regulator Required 316SS
11 Fluid State Gas/Vapour 61 Lubricator & Pneumatic Conn. Required 1/2" NPTF
12 Operating Temp. °F 120 62 Max. Degree of Rotation 90 degree
13 Operating Press. Psig 510 63 Orientation Paralel to line
14 PROCESS Max. Inlet Press. Psig 600 64 Mechanical Position Indicator Red Close / Green Open
15 DATA Max. Shut Off DP Psi 600 65 Limit Stop Required
16 Design Press. Psig 600 66 ACTUATOR Overload Protection Required
17 Design Temp. °F 150 67 Break & Run Torque Note 5
18 Predicted Sound Level dB 85 (Note.5) 68 End Torque Note 5
19 69 Opening & Closing Time Note 14
20 Manufacturer Note 4 70 Adjustable Stroking Time Note 5
21 Model No. Note 5 71 Valve DP for Sizing 600 Psi
22 Design Code API 6D 72 Actuator Test Pressure Required
23 Piping Valve Spec BA-BA-3-2 73 Man. Override / Hand Wheel N/A
24 Valve Type Ball 74 Valve Control Station Set Required
25 Type Of Body Ball 3 Piece Body 75 Fire Safe N/A
26 Body Size Port Size 8" Full Bore 76 Paint & Finish Note 9, Red (RAL 3002)
27 Configuration Bonnet Trunnion Bolted 77 Air Consumption Note 5
28 Max. Degree Of Rotation 90 degree 78 Identification Plate Note 1
29 Fire Safe Design Yes API 6FA 79 IAS Operating Pressure 120 Psig
30 End Connection Size & Rating 8"-300#, RF 80 Tubing / Fitting Material 316SS
31 End Connection Type Flange RF (Note 8) 81 Partial Stroke Facility No (Note. 17)
32 Body & Bonnet Material ASTM A105 82 Actuator Material Note 5
33 Ball / Disc Material ASTM A182 GR F316 83 Tag No. Open Position 23-ZSO-0106B
34 Stem Material ASTM A276 F316 84 Tag No. Close Position 23-ZSC-0106B
35 Seat Material ASTM A182 GR F316 85 Cable Entry Size 3/4" NPTF
SWITCHES
36 Seat Ring Material Note 5 86 Contact Config. / Rating SPDT, 24 VDC, 1 A
37 VALVE Seat Insert Material Filled TFE (Note 5) 87 Limit Switch Type 2ea Hermetically Sealed, Dry Contact
38 Seal Material Filled TFE (Note 5) 88
39 Packing Material Filled TFE 89 Tag No. 23-SOV-0106B
ASTM A193 GR B7M Hot Dip Spun
40 Bonnet Bolts Material 90 Cable Entry Size 1/2" NPTF
Galvanized
ASTM A194 GR 2HM Hot Dip Spun
41 Bonnet Nuts Material 91 SOLENOID Solenoid Type / Material 3 Way Valve / 316 SS
Galvanized
Replaceable Ball & Seat, Anti Static VALVE
42 Ball & Seat Design Seat Ring, Side Entry, 92 Manual Reset Yes
Anti Blow Out Stem
43 Leakage Class Class VI ANSI FCI 70.2 93 Degree of Protection Explosion Proof Eex'd'
44 Break & Run Torque Note 5 94
45 Piggable N/A 95 Requisition Number Note 5
46 Fail Position Fail Close (FC) 96
47 Identification Plate Note 1 97
PURCHASE
48 Weight Note 5 98
49 Control Scheme Note 5 99
50 Block & Bleed N/A 100

NOTES :
1. Instruments shall have attached SS name plate which is hard stamped or engraved with tag number.
2. All exhaust port shall be provided with bug screen 316 SS.
3. The actuator shall be sized for 130% of the required valve reset/break torque at site maximum differential pressure as applicable.
4. As per COPI Pre-Approved Manufacturers-Fabricators List, ID-G-BU-GG0-AML-GN-00-0001 latest revision.
5. VTA = vendor to advise.
6. Valves shall be as per API 6D, fire tested as per API 6FA or API 607, and hydrotested as per API 598 or ISO 5208
7. All electronic components shall be explosion proof type suitable for area classification and certified by authorities body.
8. Flange facing & finish shall be as per ASME B16.5
9. Valve, actuator and accessories shall be painted as per Mfr Std, refer to Maintenance Coating Specification for Offshore and Onshore Facilities, ID-G-BU-DD3-STS-GN-98-0002.
10. Maximum sound level shall be 85 dBA at 3 feet distance from valve
11. All valves shall refer to COPI spec. Pipe, Valves and Fittings, ID-N-BU-LL0-STS-GN-00-0002 and all reference docs as indicated in General Notes.
12. Vendor shall submit torque table sizing to be checked and verified.
13. The instrument air pressure will have a normal pressure of 100 Psig. However actuators shall be capable of operating reliably with a supply pressure of 70 to 135 Psig.
14. Actuators shall be sized to allow closing stroking times not exceed 3 seconds plus 1 second for every 1" of valve body size.
15. Vendor shall test of hydrotest and gas test per code witness by purchaser, vendor shall provide enough notification of testing witnes
16. Vendor shall re-test (as test per code) periods valve all testing at indonesian testing facilities witnees by manufacturer prior deliverid to site
17. Stroke test will do periodically in the same time during unit gas compressor preventive maintenance schedulewithin 1500 Run-hours or 2 month activate from
from UCP in manual mode
 INSTRUMENT DATASHEET DOC. NO.:

ID-N-RW-JJ1-DSR-ST-87-3001
ON-OFF VALVES / SDV / BDV
Page : 13 of 21

PROJECT :
LTRO-1B LP COMPRESSOR PACKAGE RENTAL Issued for Use 2 19-Mar-20 PS ANR TU
PROJECT DESCRIPTION REV DATE BY CHK'D APPV'D
1 Tag No. 23-SDV-0103C 51 Manufacturer Note 4

2 Service Inlet LTR LP Compressor Package-C 52 Model Note 5

3 P & Id No. ID-N-RW-PP0-PID-ST-23-3004 53 Actuator Type Pneumatic Piston with Spring Return
4 GENERAL Line No. 10"-GP-23-0720-BA1 54 Acting Type Single Acting
5 Line Size / Wall Thickness / Pipe Id 10" 55 Spring Return Yes
6 Piping Class 300# - RF 56 Actuator Mechanism Scotch Yoke
7 Area Classification Class 1, Div 2, Group D 57 Operational Position Open
8 58 Air Failure Position Close
9 59 Air Supply Pressure Note 13
10 Process Fluid Hydrocarbon 60 Filter & Regulator Required 316SS
11 Fluid State Gas/Vapour 61 Lubricator & Pneumatic Conn. Required 1/2" NPTF
12 Operating Temp. °F 102.2 62 Max. Degree of Rotation 90 degree
13 Operating Press. Psig 200 -275 63 Orientation Paralel to line
14 PROCESS Max. Inlet Press. Psig 350 64 Mechanical Position Indicator Red Close / Green Open
15 DATA Max. Shut Off DP Psi 350 65 Limit Stop Required
16 Design Press. Psig 350 66 ACTUATOR Overload Protection Required
17 Design Temp. °F 150 67 Break & Run Torque Note 5
18 Predicted Sound Level dB 85 (Note.5) 68 End Torque Note 5
19 69 Opening & Closing Time Note 14
20 Manufacturer Note 4 70 Adjustable Stroking Time Note 5
21 Model No. Note 5 71 Valve DP for Sizing 350 Psi
22 Design Code API 6D 72 Actuator Test Pressure Required
23 Piping Valve Spec BA-BA-3-2 73 Man. Override / Hand Wheel N/A
24 Valve Type Ball 74 Valve Control Station Set Required
25 Type Of Body Ball 3 Piece Body 75 Fire Safe N/A
26 Body Size Port Size 10" Full Bore 76 Paint & Finish Note 9, Red (RAL 3002)
27 Configuration Bonnet Trunnion Bolted 77 Air Consumption Note 5
28 Max. Degree Of Rotation 90 degree 78 Identification Plate Note 1
29 Fire Safe Design Yes API 6FA 79 IAS Operating Pressure 120 Psig
30 End Connection Size & Rating 10"-300#, RF 80 Tubing / Fitting Material 316SS
31 End Connection Type Flange RF (Note 8) 81 Partial Stroke Facility No (Note. 17)
32 Body & Bonnet Material ASTM A105 82 Actuator Material Note 5
33 Ball / Disc Material ASTM A182 GR F316 83 Tag No. Open Position 23-ZSO-0103C
34 Stem Material ASTM A276 F316 84 Tag No. Close Position 23-ZSC-0103C
35 Seat Material ASTM A182 GR F316 85 Cable Entry Size 3/4" NPTF
SWITCHES
36 Seat Ring Material Note 5 86 Contact Config. / Rating SPDT, 24 VDC, 1 A
37 VALVE Seat Insert Material Filled TFE (Note 5) 87 Limit Switch Type 2ea Hermetically Sealed, Dry Contact
38 Seal Material Filled TFE (Note 5) 88
39 Packing Material Filled TFE 89 Tag No. 23-SOV-0103C
ASTM A193 GR B7M Hot Dip Spun
40 Bonnet Bolts Material 90 Cable Entry Size 1/2" NPTF
Galvanized
ASTM A194 GR 2HM Hot Dip Spun
41 Bonnet Nuts Material 91 SOLENOID Solenoid Type / Material 3 Way Valve / 316 SS
Galvanized
Replaceable Ball & Seat, Anti Static VALVE
42 Ball & Seat Design Seat Ring, Side Entry, 92 Manual Reset Yes
Anti Blow Out Stem
43 Leakage Class Class VI ANSI FCI 70.2 93 Degree of Protection Explosion Proof Eex'd'
44 Break & Run Torque Note 5 94
45 Piggable N/A 95 Requisition Number Note 5
46 Fail Position Fail Close (FC) 96
47 Identification Plate Note 1 97
PURCHASE
48 Weight Note 5 98
49 Control Scheme Note 5 99
50 Block & Bleed N/A 100

NOTES :
1. Instruments shall have attached SS name plate which is hard stamped or engraved with tag number.
2. All exhaust port shall be provided with bug screen 316 SS.
3. The actuator shall be sized for 130% of the required valve reset/break torque at site maximum differential pressure as applicable.
4. As per COPI Pre-Approved Manufacturers-Fabricators List, ID-G-BU-GG0-AML-GN-00-0001 latest revision.
5. VTA = vendor to advise.
6. Valves shall be as per API 6D, fire tested as per API 6FA or API 607, and hydrotested as per API 598 or ISO 5208
7. All electronic components shall be explosion proof type suitable for area classification and certified by authorities body.
8. Flange facing & finish shall be as per ASME B16.5
9. Valve, actuator and accessories shall be painted as per Mfr Std, refer to Maintenance Coating Specification for Offshore and Onshore Facilities, ID-G-BU-DD3-STS-GN-98-0002.
10. Maximum sound level shall be 85 dBA at 3 feet distance from valve
11. All valves shall refer to COPI spec. Pipe, Valves and Fittings, ID-N-BU-LL0-STS-GN-00-0002 and all reference docs as indicated in General Notes.
12. Vendor shall submit torque table sizing to be checked and verified.
13. The instrument air pressure will have a normal pressure of 100 Psig. However actuators shall be capable of operating reliably with a supply pressure of 70 to 135 Psig.
14. Actuators shall be sized to allow closing stroking times not exceed 3 seconds plus 1 second for every 1" of valve body size.
15. Vendor shall test of hydrotest and gas test per code witness by purchaser, vendor shall provide enough notification of testing witnes
16. Vendor shall re-test (as test per code) periods valve all testing at indonesian testing facilities witnees by manufacturer prior deliverid to site
17. Stroke test will do periodically in the same time during unit gas compressor preventive maintenance schedulewithin 1500 Run-hours or 2 month activate from
from UCP in manual mode
 INSTRUMENT DATASHEET DOC. NO.:

ID-N-RW-JJ1-DSR-ST-87-3001
ON-OFF VALVES / SDV / BDV
Page : 14 of 21

PROJECT :
LTRO-1B LP COMPRESSOR PACKAGE RENTAL Issued for Use 2 19-Mar-20 PS ANR TU
PROJECT DESCRIPTION REV DATE BY CHK'D APPV'D
1 Tag No. 23-SDV-0106C 51 Manufacturer Note 4

2 Service Outlet LTR LP Compressor Package-C 52 Model Note 5

3 P & Id No. ID-N-RW-PP0-PID-ST-23-3004 53 Actuator Type Pneumatic Piston with Spring Return
4 GENERAL Line No. 8"-GP-23-0721-BA1 54 Acting Type Single Acting
5 Line Size / Wall Thickness / Pipe Id 8" 55 Spring Return Yes
6 Piping Class 300# - RF 56 Actuator Mechanism Scotch Yoke
7 Area Classification Class 1, Div 2, Group D 57 Operational Position Open
8 58 Air Failure Position Close
9 59 Air Supply Pressure Note 13
10 Process Fluid Hydrocarbon 60 Filter & Regulator Required 316SS
11 Fluid State Gas/Vapour 61 Lubricator & Pneumatic Conn. Required 1/2" NPTF
12 Operating Temp. °F 120 62 Max. Degree of Rotation 90 degree
13 Operating Press. Psig 510 63 Orientation Paralel to line
14 PROCESS Max. Inlet Press. Psig 600 64 Mechanical Position Indicator Red Close / Green Open
15 DATA Max. Shut Off DP Psi 600 65 Limit Stop Required
16 Design Press. Psig 600 66 ACTUATOR Overload Protection Required
17 Design Temp. °F 150 67 Break & Run Torque Note 5
18 Predicted Sound Level dB 85 (Note.5) 68 End Torque Note 5
19 69 Opening & Closing Time Note 14
20 Manufacturer Note 4 70 Adjustable Stroking Time Note 5
21 Model No. Note 5 71 Valve DP for Sizing 600 Psi
22 Design Code API 6D 72 Actuator Test Pressure Required
23 Piping Valve Spec BA-BA-3-2 73 Man. Override / Hand Wheel N/A
24 Valve Type Ball 74 Valve Control Station Set Required
25 Type Of Body Ball 3 Piece Body 75 Fire Safe N/A
26 Body Size Port Size 8" Full Bore 76 Paint & Finish Note 9, Red (RAL 3002)
27 Configuration Bonnet Trunnion Bolted 77 Air Consumption Note 5
28 Max. Degree Of Rotation 90 degree 78 Identification Plate Note 1
29 Fire Safe Design Yes API 6FA 79 IAS Operating Pressure 120 Psig
30 End Connection Size & Rating 8"-300#, RF 80 Tubing / Fitting Material 316SS
31 End Connection Type Flange RF (Note 8) 81 Partial Stroke Facility No (Note. 17)
32 Body & Bonnet Material ASTM A105 82 Actuator Material Note 5
33 Ball / Disc Material ASTM A182 GR F316 83 Tag No. Open Position 23-ZSO-0106C
34 Stem Material ASTM A276 F316 84 Tag No. Close Position 23-ZSC-0106C
35 Seat Material ASTM A182 GR F316 85 Cable Entry Size 3/4" NPTF
SWITCHES
36 Seat Ring Material Note 5 86 Contact Config. / Rating SPDT, 24 VDC, 1 A
37 VALVE Seat Insert Material Filled TFE (Note 5) 87 Limit Switch Type 2ea Hermetically Sealed, Dry Contact
38 Seal Material Filled TFE (Note 5) 88
39 Packing Material Filled TFE 89 Tag No. 23-SOV-0106C
ASTM A193 GR B7M Hot Dip Spun
40 Bonnet Bolts Material 90 Cable Entry Size 1/2" NPTF
Galvanized
ASTM A194 GR 2HM Hot Dip Spun
41 Bonnet Nuts Material 91 SOLENOID Solenoid Type / Material 3 Way Valve / 316 SS
Galvanized
Replaceable Ball & Seat, Anti Static VALVE
42 Ball & Seat Design Seat Ring, Side Entry, 92 Manual Reset Yes
Anti Blow Out Stem
43 Leakage Class Class VI ANSI FCI 70.2 93 Degree of Protection Explosion Proof Eex'd'
44 Break & Run Torque Note 5 94
45 Piggable N/A 95 Requisition Number Note 5
46 Fail Position Fail Close (FC) 96
47 Identification Plate Note 1 97
PURCHASE
48 Weight Note 5 98
49 Control Scheme Note 5 99
50 Block & Bleed N/A 100

NOTES :
1. Instruments shall have attached SS name plate which is hard stamped or engraved with tag number.
2. All exhaust port shall be provided with bug screen 316 SS.
3. The actuator shall be sized for 130% of the required valve reset/break torque at site maximum differential pressure as applicable.
4. As per COPI Pre-Approved Manufacturers-Fabricators List, ID-G-BU-GG0-AML-GN-00-0001 latest revision.
5. VTA = vendor to advise.
6. Valves shall be as per API 6D, fire tested as per API 6FA or API 607, and hydrotested as per API 598 or ISO 5208
7. All electronic components shall be explosion proof type suitable for area classification and certified by authorities body.
8. Flange facing & finish shall be as per ASME B16.5
9. Valve, actuator and accessories shall be painted as per Mfr Std, refer to Maintenance Coating Specification for Offshore and Onshore Facilities, ID-G-BU-DD3-STS-GN-98-0002.
10. Maximum sound level shall be 85 dBA at 3 feet distance from valve
11. All valves shall refer to COPI spec. Pipe, Valves and Fittings, ID-N-BU-LL0-STS-GN-00-0002 and all reference docs as indicated in General Notes.
12. Vendor shall submit torque table sizing to be checked and verified.
13. The instrument air pressure will have a normal pressure of 100 Psig. However actuators shall be capable of operating reliably with a supply pressure of 70 to 135 Psig.
14. Actuators shall be sized to allow closing stroking times not exceed 3 seconds plus 1 second for every 1" of valve body size.
15. Vendor shall test of hydrotest and gas test per code witness by purchaser, vendor shall provide enough notification of testing witnes
16. Vendor shall re-test (as test per code) periods valve all testing at indonesian testing facilities witnees by manufacturer prior deliverid to site
17. Stroke test will do periodically in the same time during unit gas compressor preventive maintenance schedulewithin 1500 Run-hours or 2 month activate from
from UCP in manual mode
 INSTRUMENT DATASHEET DOC. NO.:

ID-N-RW-JJ1-DSR-ST-87-3001
ON-OFF VALVES / SDV / BDV
Page : 15 of 21

PROJECT :
LTRO-1B LP COMPRESSOR PACKAGE RENTAL Issued for Use 2 19-Mar-20 PS ANR TU
PROJECT DESCRIPTION REV DATE BY CHK'D APPV'D
1 Tag No. 23-BDV-202A 51 Manufacturer Note 4
On skid Compressor Outlet Gas to Flare
2 Service 52 Model Note 5
Header
3 P & Id No. ID-N-RW-PP0-PID-ST-23-3003 53 Actuator Type Pneumatic Piston with Spring Return
4 GENERAL Line No. 2"-VFL-1202A-A1 54 Acting Type Single Acting
5 Line Size / Wall Thickness / Pipe Id 2" 55 Spring Return Yes
6 Piping Class 300# - RF 56 Actuator Mechanism Scotch Yoke
7 Area Classification Class 1, Div 2, Group D 57 Operational Position Close
8 58 Air Failure Position Open
9 59 Air Supply Pressure Note 13
10 Process Fluid Hydrocarbon 60 Filter & Regulator Required 316SS
11 Fluid State Gas/Vapour 61 Lubricator & Pneumatic Conn. Required 1/2" NPTF
12 Operating Temp. °F 120 62 Max. Degree of Rotation 90 degree
13 Operating Press. Psig 510 63 Orientation Paralel to line
14 PROCESS Max. Inlet Press. Psig 600 64 Mechanical Position Indicator Red Close / Green Open
15 DATA Max. Shut Off DP Psi 600 65 Limit Stop Required
16 Design Press. Psig 600 66 ACTUATOR Overload Protection Required
17 Design Temp. °F 150 67 Break & Run Torque Note 5
18 Predicted Sound Level dB 85 (Note.5) 68 End Torque Note 5
19 69 Opening & Closing Time Note 14
20 Manufacturer Note 4 70 Adjustable Stroking Time Note 5
21 Model No. Note 5 71 Valve DP for Sizing 600 Psi
22 Design Code API 6D 72 Actuator Test Pressure Required
23 Piping Valve Spec BA-BA-3-2 73 Man. Override / Hand Wheel N/A
24 Valve Type Ball 74 Valve Control Station Set Required
25 Type Of Body Ball 3 Piece Body 75 Fire Safe N/A
26 Body Size Port Size 2" Full Bore 76 Paint & Finish Note 9, Red (RAL 3002)
27 Configuration Bonnet Trunnion Bolted 77 Air Consumption Note 5
28 Max. Degree Of Rotation 90 degree 78 Identification Plate Note 1
29 Fire Safe Design Yes API 6FA 79 IAS Operating Pressure 120 Psig
30 End Connection Size & Rating 2"-300#, RF 80 Tubing / Fitting Material 316SS
31 End Connection Type Flange RF (Note 8) 81 Partial Stroke Facility No (Note. 17)
32 Body & Bonnet Material ASTM A105 82 Actuator Material Note 5
33 Ball / Disc Material ASTM A182 GR F316 83 Tag No. Open Position 60-ZSO-0002
34 Stem Material ASTM A276 F316 84 Tag No. Close Position 60-ZSC-0002
35 Seat Material ASTM A182 GR F316 85 Cable Entry Size 3/4" NPTF
SWITCHES
36 Seat Ring Material Note 5 86 Contact Config. / Rating SPDT, 24 VDC, 1 A
37 VALVE Seat Insert Material Filled TFE (Note 5) 87 Limit Switch Type 2ea Hermetically Sealed, Dry Contact
38 Seal Material Filled TFE (Note 5) 88
39 Packing Material Filled TFE 89 Tag No. 60-SOV-0002
ASTM A193 GR B7M Hot Dip Spun
40 Bonnet Bolts Material 90 Cable Entry Size 1/2" NPTF
Galvanized
ASTM A194 GR 2HM Hot Dip Spun
41 Bonnet Nuts Material 91 SOLENOID Solenoid Type / Material 3 Way Valve / 316 SS
Galvanized
Replaceable Ball & Seat, Anti Static VALVE
42 Ball & Seat Design Seat Ring, Side Entry, 92 Manual Reset No
Anti Blow Out Stem
43 Leakage Class Class VI ANSI FCI 70.2 93 Degree of Protection Explosion Proof Eex'd'
44 Break & Run Torque Note 5 94
45 Piggable N/A 95 Requisition Number Note 5
46 Fail Position Fail Open (FO) 96
47 Identification Plate Note 1 97
PURCHASE
48 Weight Note 5 98
49 Control Scheme Note 5 99
50 Block & Bleed N/A 100

NOTES :
1. Instruments shall have attached SS name plate which is hard stamped or engraved with tag number.
2. All exhaust port shall be provided with bug screen 316 SS.
3. The actuator shall be sized for 130% of the required valve reset/break torque at site maximum differential pressure as applicable.
4. As per COPI Pre-Approved Manufacturers-Fabricators List, ID-G-BU-GG0-AML-GN-00-0001 latest revision.
5. VTA = vendor to advise.
6. Valves shall be as per API 6D, fire tested as per API 6FA or API 607, and hydrotested as per API 598 or ISO 5208
7. All electronic components shall be explosion proof type suitable for area classification and certified by authorities body.
8. Flange facing & finish shall be as per ASME B16.5
9. Valve, actuator and accessories shall be painted as per Mfr Std, refer to Maintenance Coating Specification for Offshore and Onshore Facilities, ID-G-BU-DD3-STS-GN-98-0002.
10. Maximum sound level shall be 85 dBA at 3 feet distance from valve
11. All valves shall refer to COPI spec. Pipe, Valves and Fittings, ID-N-BU-LL0-STS-GN-00-0002 and all reference docs as indicated in General Notes.
12. Vendor shall submit torque table sizing to be checked and verified.
13. The instrument air pressure will have a normal pressure of 100 Psig. However actuators shall be capable of operating reliably with a supply pressure of 70 to 135 Psig.
14. Actuators shall be sized to allow closing stroking times not exceed 3 seconds plus 1 second for every 1" of valve body size.
15. Vendor shall test of hydrotest and gas test per code witness by purchaser, vendor shall provide enough notification of testing witnes
16. Vendor shall re-test (as test per code) periods valve all testing at indonesian testing facilities witnees by manufacturer prior deliverid to site
17. Stroke test will do periodically in the same time during unit gas compressor preventive maintenance schedulewithin 1500 Run-hours or 2 month activate from
from UCP in manual mode
 INSTRUMENT DATASHEET DOC. NO.:

ID-N-RW-JJ1-DSR-ST-87-3001
ON-OFF VALVES / SDV / BDV
Page : 16 of 21

PROJECT :
LTRO-1B LP COMPRESSOR PACKAGE RENTAL Issued for Use 2 19-Mar-20 PS ANR TU
PROJECT DESCRIPTION REV DATE BY CHK'D APPV'D
1 Tag No. 23-BDV-202B 51 Manufacturer Note 4
On skid Compressor Outlet Gas to Flare
2 Service 52 Model Note 5
Header
3 P & Id No. ID-N-RW-PP0-PID-ST-23-3006
2"-VFL-1202B-A1 53 Actuator Type Pneumatic Piston with Spring Return
4 GENERAL Line No. 8"-GP-BA1-20-0599 54 Acting Type Single Acting
5 Line Size / Wall Thickness / Pipe Id 2" 55 Spring Return Yes
6 Piping Class 300# - RF 56 Actuator Mechanism Scotch Yoke
7 Area Classification Class 1, Div 2, Group D 57 Operational Position Close
8 58 Air Failure Position Open
9 59 Air Supply Pressure Note 13
10 Process Fluid Hydrocarbon 60 Filter & Regulator Required 316SS
11 Fluid State Gas/Vapour 61 Lubricator & Pneumatic Conn. Required 1/2" NPTF
12 Operating Temp. °F 120 62 Max. Degree of Rotation 90 degree
13 Operating Press. Psig 510 63 Orientation Paralel to line
14 PROCESS Max. Inlet Press. Psig 600 64 Mechanical Position Indicator Red Close / Green Open
15 DATA Max. Shut Off DP Psi 600 65 Limit Stop Required
16 Design Press. Psig 600 66 ACTUATOR Overload Protection Required
17 Design Temp. °F 150 67 Break & Run Torque Note 5
18 Predicted Sound Level dB 85 (Note.5) 68 End Torque Note 5
19 69 Opening & Closing Time Note 14
20 Manufacturer Note 4 70 Adjustable Stroking Time Note 5
21 Model No. Note 5 71 Valve DP for Sizing 600 Psi
22 Design Code API 6D 72 Actuator Test Pressure Required
23 Piping Valve Spec BA-BA-3-2 73 Man. Override / Hand Wheel N/A
24 Valve Type Ball 74 Valve Control Station Set Required
25 Type Of Body Ball 3 Piece Body 75 Fire Safe N/A
26 Body Size Port Size 2" Full Bore 76 Paint & Finish Note 9, Red (RAL 3002)
27 Configuration Bonnet Trunnion Bolted 77 Air Consumption Note 5
28 Max. Degree Of Rotation 90 degree 78 Identification Plate Note 1
29 Fire Safe Design Yes API 6FA 79 IAS Operating Pressure 120 Psig
30 End Connection Size & Rating 2"-300#, RF 80 Tubing / Fitting Material 316SS
31 End Connection Type Flange RF (Note 8) 81 Partial Stroke Facility No (Note. 17)
32 Body & Bonnet Material ASTM A105 82 Actuator Material Note 5
33 Ball / Disc Material ASTM A182 GR F316 83 Tag No. Open Position 60-ZSO-0002
34 Stem Material ASTM A276 F316 84 Tag No. Close Position 60-ZSC-0002
35 Seat Material ASTM A182 GR F316 85 Cable Entry Size 3/4" NPTF
SWITCHES
36 Seat Ring Material Note 5 86 Contact Config. / Rating SPDT, 24 VDC, 1 A
37 VALVE Seat Insert Material Filled TFE (Note 5) 87 Limit Switch Type 2ea Hermetically Sealed, Dry Contact
38 Seal Material Filled TFE (Note 5) 88
39 Packing Material Filled TFE 89 Tag No. 60-SOV-0002
ASTM A193 GR B7M Hot Dip Spun
40 Bonnet Bolts Material 90 Cable Entry Size 1/2" NPTF
Galvanized
ASTM A194 GR 2HM Hot Dip Spun
41 Bonnet Nuts Material 91 SOLENOID Solenoid Type / Material 3 Way Valve / 316 SS
Galvanized
Replaceable Ball & Seat, Anti Static VALVE
42 Ball & Seat Design Seat Ring, Side Entry, 92 Manual Reset No
Anti Blow Out Stem
43 Leakage Class Class VI ANSI FCI 70.2 93 Degree of Protection Explosion Proof Eex'd'
44 Break & Run Torque Note 5 94
45 Piggable N/A 95 Requisition Number Note 5
46 Fail Position Fail Open (FO) 96
47 Identification Plate Note 1 97
PURCHASE
48 Weight Note 5 98
49 Control Scheme Note 5 99
50 Block & Bleed N/A 100

NOTES :
1. Instruments shall have attached SS name plate which is hard stamped or engraved with tag number.
2. All exhaust port shall be provided with bug screen 316 SS.
3. The actuator shall be sized for 130% of the required valve reset/break torque at site maximum differential pressure as applicable.
4. As per COPI Pre-Approved Manufacturers-Fabricators List, ID-G-BU-GG0-AML-GN-00-0001 latest revision.
5. VTA = vendor to advise.
6. Valves shall be as per API 6D, fire tested as per API 6FA or API 607, and hydrotested as per API 598 or ISO 5208
7. All electronic components shall be explosion proof type suitable for area classification and certified by authorities body.
8. Flange facing & finish shall be as per ASME B16.5
9. Valve, actuator and accessories shall be painted as per Mfr Std, refer to Maintenance Coating Specification for Offshore and Onshore Facilities, ID-G-BU-DD3-STS-GN-98-0002.
10. Maximum sound level shall be 85 dBA at 3 feet distance from valve
11. All valves shall refer to COPI spec. Pipe, Valves and Fittings, ID-N-BU-LL0-STS-GN-00-0002 and all reference docs as indicated in General Notes.
12. Vendor shall submit torque table sizing to be checked and verified.
13. The instrument air pressure will have a normal pressure of 100 Psig. However actuators shall be capable of operating reliably with a supply pressure of 70 to 135 Psig.
14. Actuators shall be sized to allow closing stroking times not exceed 3 seconds plus 1 second for every 1" of valve body size.
15. Vendor shall test of hydrotest and gas test per code witness by purchaser, vendor shall provide enough notification of testing witnes
16. Vendor shall re-test (as test per code) periods valve all testing at indonesian testing facilities witnees by manufacturer prior deliverid to site
17. Stroke test will do periodically in the same time during unit gas compressor preventive maintenance schedulewithin 1500 Run-hours or 2 month activate from
from UCP in manual mode
 INSTRUMENT DATASHEET DOC. NO.:

ID-N-RW-JJ1-DSR-ST-87-3001
ON-OFF VALVES / SDV / BDV
Page : 17 of 21

PROJECT :
LTRO-1B LP COMPRESSOR PACKAGE RENTAL Issued for Use 2 19-Mar-20 PS ANR TU
PROJECT DESCRIPTION REV DATE BY CHK'D APPV'D
1 Tag No. 23-BDV-202C 51 Manufacturer Note 4
On skid Compressor Outlet Gas to Flare
2 Service 52 Model Note 5
Header
3 P & Id No. ID-N-RW-PP0-PID-ST-23-3006
2"-VFL-1202C-A1 53 Actuator Type Pneumatic Piston with Spring Return
4 GENERAL Line No. 8"-GP-BA1-20-0599 54 Acting Type Single Acting
5 Line Size / Wall Thickness / Pipe Id 2" 55 Spring Return Yes
6 Piping Class 300# - RF 56 Actuator Mechanism Scotch Yoke
7 Area Classification Class 1, Div 2, Group D 57 Operational Position Close
8 58 Air Failure Position Open
9 59 Air Supply Pressure Note 13
10 Process Fluid Hydrocarbon 60 Filter & Regulator Required 316SS
11 Fluid State Gas/Vapour 61 Lubricator & Pneumatic Conn. Required 1/2" NPTF
12 Operating Temp. °F 120 62 Max. Degree of Rotation 90 degree
13 Operating Press. Psig 510 63 Orientation Paralel to line
14 PROCESS Max. Inlet Press. Psig 600 64 Mechanical Position Indicator Red Close / Green Open
15 DATA Max. Shut Off DP Psi 600 65 Limit Stop Required
16 Design Press. Psig 600 66 ACTUATOR Overload Protection Required
17 Design Temp. °F 150 67 Break & Run Torque Note 5
18 Predicted Sound Level dB 85 (Note.5) 68 End Torque Note 5
19 69 Opening & Closing Time Note 14
20 Manufacturer Note 4 70 Adjustable Stroking Time Note 5
21 Model No. Note 5 71 Valve DP for Sizing 600 Psi
22 Design Code API 6D 72 Actuator Test Pressure Required
23 Piping Valve Spec BA-BA-3-2 73 Man. Override / Hand Wheel N/A
24 Valve Type Ball 74 Valve Control Station Set Required
25 Type Of Body Ball 3 Piece Body 75 Fire Safe N/A
26 Body Size Port Size 2" Full Bore 76 Paint & Finish Note 9, Red (RAL 3002)
27 Configuration Bonnet Trunnion Bolted 77 Air Consumption Note 5
28 Max. Degree Of Rotation 90 degree 78 Identification Plate Note 1
29 Fire Safe Design Yes API 6FA 79 IAS Operating Pressure 120 Psig
30 End Connection Size & Rating 2"-300#, RF 80 Tubing / Fitting Material 316SS
31 End Connection Type Flange RF (Note 8) 81 Partial Stroke Facility No (Note. 17)
32 Body & Bonnet Material ASTM A105 82 Actuator Material Note 5
33 Ball / Disc Material ASTM A182 GR F316 83 Tag No. Open Position 60-ZSO-0002
34 Stem Material ASTM A276 F316 84 Tag No. Close Position 60-ZSC-0002
35 Seat Material ASTM A182 GR F316 85 Cable Entry Size 3/4" NPTF
SWITCHES
36 Seat Ring Material Note 5 86 Contact Config. / Rating SPDT, 24 VDC, 1 A
37 VALVE Seat Insert Material Filled TFE (Note 5) 87 Limit Switch Type 2ea Hermetically Sealed, Dry Contact
38 Seal Material Filled TFE (Note 5) 88
39 Packing Material Filled TFE 89 Tag No. 60-SOV-0002
ASTM A193 GR B7M Hot Dip Spun
40 Bonnet Bolts Material 90 Cable Entry Size 1/2" NPTF
Galvanized
ASTM A194 GR 2HM Hot Dip Spun
41 Bonnet Nuts Material 91 SOLENOID Solenoid Type / Material 3 Way Valve / 316 SS
Galvanized
Replaceable Ball & Seat, Anti Static VALVE
42 Ball & Seat Design Seat Ring, Side Entry, 92 Manual Reset No
Anti Blow Out Stem
43 Leakage Class Class VI ANSI FCI 70.2 93 Degree of Protection Explosion Proof Eex'd'
44 Break & Run Torque Note 5 94
45 Piggable N/A 95 Requisition Number Note 5
46 Fail Position Fail Open (FO) 96
47 Identification Plate Note 1 97
PURCHASE
48 Weight Note 5 98
49 Control Scheme Note 5 99
50 Block & Bleed N/A 100

NOTES :
1. Instruments shall have attached SS name plate which is hard stamped or engraved with tag number.
2. All exhaust port shall be provided with bug screen 316 SS.
3. The actuator shall be sized for 130% of the required valve reset/break torque at site maximum differential pressure as applicable.
4. As per COPI Pre-Approved Manufacturers-Fabricators List, ID-G-BU-GG0-AML-GN-00-0001 latest revision.
5. VTA = vendor to advise.
6. Valves shall be as per API 6D, fire tested as per API 6FA or API 607, and hydrotested as per API 598 or ISO 5208
7. All electronic components shall be explosion proof type suitable for area classification and certified by authorities body.
8. Flange facing & finish shall be as per ASME B16.5
9. Valve, actuator and accessories shall be painted as per Mfr Std, refer to Maintenance Coating Specification for Offshore and Onshore Facilities, ID-G-BU-DD3-STS-GN-98-0002.
10. Maximum sound level shall be 85 dBA at 3 feet distance from valve
11. All valves shall refer to COPI spec. Pipe, Valves and Fittings, ID-N-BU-LL0-STS-GN-00-0002 and all reference docs as indicated in General Notes.
12. Vendor shall submit torque table sizing to be checked and verified.
13. The instrument air pressure will have a normal pressure of 100 Psig. However actuators shall be capable of operating reliably with a supply pressure of 70 to 135 Psig.
14. Actuators shall be sized to allow closing stroking times not exceed 3 seconds plus 1 second for every 1" of valve body size.
15. Vendor shall test of hydrotest and gas test per code witness by purchaser, vendor shall provide enough notification of testing witnes
16. Vendor shall re-test (as test per code) periods valve all testing at indonesian testing facilities witnees by manufacturer prior deliverid to site
17. Stroke test will do periodically in the same time during unit gas compressor preventive maintenance schedulewithin 1500 Run-hours or 2 month activate from
from UCP in manual mode
 INSTRUMENT DATASHEET DOC. NO.:

ID-N-RW-JJ1-DSR-ST-87-3001
ON-OFF VALVES / SDV / BDV
Page : 18 of 21

PROJECT :
LTRO-1B LP COMPRESSOR PACKAGE RENTAL Issued for Use 2 19-Mar-20 PS ANR TU
PROJECT DESCRIPTION REV DATE BY CHK'D APPV'D
1 Tag No. 60-SDV-0001 51 Manufacturer Note 4

2 Service Fuel Gas Header to Fuel Gas Scrubber 52 Model Note 5

3 P & Id No. ID-N-RW-PP0-PID-ST-60-3001 53 Actuator Type Pneumatic Piston with Spring Return
4 GENERAL Line No. 3"-GP-60-0636-BA1 54 Acting Type Single Acting
5 Line Size / Wall Thickness / Pipe Id 3" 55 Spring Return Yes
6 Piping Class 300# - RF 56 Actuator Mechanism Scotch Yoke
7 Area Classification Class 1, Div 2, Group D 57 Operational Position Open
8 58 Air Failure Position Close
9 59 Air Supply Pressure Note 13
10 Process Fluid Hydrocarbon 60 Filter & Regulator Required 316SS
11 Fluid State Liquid/Gas 61 Lubricator & Pneumatic Conn. Required 1/2" NPTF
12 Operating Temp. °F 102.2 62 Max. Degree of Rotation 90 degree
13 Operating Press. Psig 170 63 Orientation Paralel to line
14 PROCESS Max. Inlet Press. Psig 250 64 Mechanical Position Indicator Red Close / Green Open
15 DATA Max. Shut Off DP Psi 250 65 Limit Stop Required
16 Design Press. Psig 250 66 ACTUATOR Overload Protection Required
17 Design Temp. °F 150 67 Break & Run Torque Note 5
18 Predicted Sound Level dB 85 (Note.5) 68 End Torque Note 5
19 69 Opening & Closing Time Note 14
20 Manufacturer Note 4 70 Adjustable Stroking Time Note 5
21 Model No. Note 5 71 Valve DP for Sizing 250 Psi
22 Design Code API 6D 72 Actuator Test Pressure Required
23 Piping Valve Spec BA-BA-3-2 73 Man. Override / Hand Wheel N/A
24 Valve Type Ball 74 Valve Control Station Set Required
25 Type Of Body Ball 3 Piece Body 75 Fire Safe N/A
26 Body Size Port Size 3" Full Bore 76 Paint & Finish Note 9, Red (RAL 3002)
27 Configuration Bonnet Trunnion Bolted 77 Air Consumption Note 5
28 Max. Degree Of Rotation 90 degree 78 Identification Plate Note 1
29 Fire Safe Design Yes API 6FA 79 IAS Operating Pressure 120 Psig
30 End Connection Size & Rating 3"-300#, RF 80 Tubing / Fitting Material 316SS
31 End Connection Type Flange RF (Note 8) 81 Partial Stroke Facility Yes (Local)
32 Body & Bonnet Material ASTM A105 82 Actuator Material Note 5
33 Ball / Disc Material ASTM A182 GR F316 83 Tag No. Open Position 60-ZSO-0001
34 Stem Material ASTM A276 F316 84 Tag No. Close Position 60-ZSC-0001
35 Seat Material ASTM A182 GR F316 85 Cable Entry Size 3/4" NPTF
SWITCHES
36 Seat Ring Material Note 5 86 Contact Config. / Rating SPDT, 24 VDC, 1 A
37 VALVE Seat Insert Material Filled TFE (Note 5) 87 Limit Switch Type 2ea Hermetically Sealed, Dry Contact
38 Seal Material Filled TFE (Note 5) 88
39 Packing Material Filled TFE 89 Tag No. 60-SOV-0001
ASTM A193 GR B7M Hot Dip Spun
40 Bonnet Bolts Material 90 Cable Entry Size 1/2" NPTF
Galvanized
ASTM A194 GR 2HM Hot Dip Spun
41 Bonnet Nuts Material 91 SOLENOID Solenoid Type / Material 3 Way Valve / 316 SS
Galvanized
Replaceable Ball & Seat, Anti Static VALVE
42 Ball & Seat Design Seat Ring, Side Entry, 92 Manual Reset Yes
Anti Blow Out Stem
43 Leakage Class Class VI ANSI FCI 70.2 93 Degree of Protection Explosion Proof Eex'd'
44 Break & Run Torque Note 5 94
45 Piggable N/A 95 Requisition Number Note 5
46 Fail Position Fail Close (FC) 96
47 Identification Plate Note 1 97
PURCHASE
48 Weight Note 5 98
49 Control Scheme Note 5 99
50 Block & Bleed N/A 100

NOTES :
1. Instruments shall have attached SS name plate which is hard stamped or engraved with tag number.
2. All exhaust port shall be provided with bug screen 316 SS.
3. The actuator shall be sized for 130% of the required valve reset/break torque at site maximum differential pressure as applicable.
4. As per COPI Pre-Approved Manufacturers-Fabricators List, ID-G-BU-GG0-AML-GN-00-0001 latest revision.
5. VTA = vendor to advise.
6. Valves shall be as per API 6D, fire tested as per API 6FA or API 607, and hydrotested as per API 598 or ISO 5208
7. All electronic components shall be explosion proof type suitable for area classification and certified by authorities body.
8. Flange facing & finish shall be as per ASME B16.5
9. Valve, actuator and accessories shall be painted as per Mfr Std, refer to Maintenance Coating Specification for Offshore and Onshore Facilities, ID-G-BU-DD3-STS-GN-98-0002.
10. Maximum sound level shall be 85 dBA at 3 feet distance from valve
11. All valves shall refer to COPI spec. Pipe, Valves and Fittings, ID-N-BU-LL0-STS-GN-00-0002 and all reference docs as indicated in General Notes.
12. Vendor shall submit torque table sizing to be checked and verified.
13. The instrument air pressure will have a normal pressure of 100 Psig. However actuators shall be capable of operating reliably with a supply pressure of 70 to 135 Psig.
14. Actuators shall be sized to allow closing stroking times not exceed 3 seconds plus 1 second for every 1" of valve body size.
15. Vendor shall test of hydrotest and gas test per code witness by purchaser, vendor shall provide enough notification of testing witnes
16. Vendor shall re-test (as test per code) periods valve all testing at indonesian testing facilities witnees by manufacturer prior deliverid to site
 INSTRUMENT DATASHEET DOC. NO.:

ID-N-RW-JJ1-DSR-ST-87-3001
ON-OFF VALVES / SDV / BDV
Page : 19 of 21

PROJECT :
LTRO-1B LP COMPRESSOR PACKAGE RENTAL Issued for Use 2 19-Mar-20 PS ANR TU
PROJECT DESCRIPTION REV DATE BY CHK'D APPV'D
1 Tag No. 60-SDV-0102 51 Manufacturer Note 4

2 Service Fuel Gas Header to LTR LP Compressor 52 Model Note 5

3 P & Id No. ID-N-RW-PP0-PID-ST-60-3002 53 Actuator Type Pneumatic Piston with Spring Return
4 GENERAL Line No. 3"-GF-60-0648-AA1 54 Acting Type Single Acting
5 Line Size / Wall Thickness / Pipe Id 3" 55 Spring Return Yes
6 Piping Class 150# - RF 56 Actuator Mechanism Scotch Yoke
7 Area Classification Class 1, Div 2, Group D 57 Operational Position Open
8 58 Air Failure Position Close
9 59 Air Supply Pressure Note 13
10 Process Fluid Hydrocarbon 60 Filter & Regulator Required 316SS
11 Fluid State Gas 61 Lubricator & Pneumatic Conn. Required 1/2" NPTF
12 Operating Temp. °F 100 62 Max. Degree of Rotation 90 degree
13 Operating Press. Psig 160 63 Orientation Paralel to line
14 PROCESS Max. Inlet Press. Psig 250 64 Mechanical Position Indicator Red Close / Green Open
15 DATA Max. Shut Off DP Psi 250 65 Limit Stop Required
16 Design Press. Psig 250 66 ACTUATOR Overload Protection Required
17 Design Temp. °F 150 67 Break & Run Torque Note 5
18 Predicted Sound Level dB 85 (Note.5) 68 End Torque Note 5
19 69 Opening & Closing Time Note 14
20 Manufacturer Note 4 70 Adjustable Stroking Time Note 5
21 Model No. Note 5 71 Valve DP for Sizing 250 Psi
22 Design Code API 6D 72 Actuator Test Pressure Required
23 Piping Valve Spec BA-AA-3-2 73 Man. Override / Hand Wheel N/A
24 Valve Type Ball 74 Valve Control Station Set Required
25 Type Of Body Ball 3 Piece Body 75 Fire Safe N/A
26 Body Size Port Size 3" Full Bore 76 Paint & Finish Note 9, Red (RAL 3002)
27 Configuration Bonnet Trunnion Bolted 77 Air Consumption Note 5
28 Max. Degree Of Rotation 90 degree 78 Identification Plate Note 1
29 Fire Safe Design Yes API 6FA 79 IAS Operating Pressure 120 Psig
30 End Connection Size & Rating 3"-150#, RF 80 Tubing / Fitting Material 316SS
31 End Connection Type Flange RF (Note 8) 81 Partial Stroke Facility Yes (Local)
32 Body & Bonnet Material ASTM A105 82 Actuator Material Note 5
33 Ball / Disc Material ASTM A182 GR F316 83 Tag No. Open Position 60-ZSO-0102
34 Stem Material ASTM A276 F316 84 Tag No. Close Position 60-ZSC-0102
35 Seat Material ASTM A182 GR F316 85 Cable Entry Size 3/4" NPTF
SWITCHES
36 Seat Ring Material Note 5 86 Contact Config. / Rating SPDT, 24 VDC, 1 A
37 VALVE Seat Insert Material Filled TFE (Note 5) 87 Limit Switch Type 2ea Hermetically Sealed, Dry Contact
38 Seal Material Filled TFE (Note 5) 88
39 Packing Material Filled TFE 89 Tag No. 60-SOV-0102
ASTM A193 GR B7M Hot Dip Spun
40 Bonnet Bolts Material 90 Cable Entry Size 1/2" NPTF
Galvanized
ASTM A194 GR 2HM Hot Dip Spun
41 Bonnet Nuts Material 91 SOLENOID Solenoid Type / Material 3 Way Valve / 316 SS
Galvanized
Replaceable Ball & Seat, Anti Static VALVE
42 Ball & Seat Design Seat Ring, Side Entry, 92 Manual Reset Yes
Anti Blow Out Stem
43 Leakage Class Class VI ANSI FCI 70.2 93 Degree of Protection Explosion Proof Eex'd'
44 Break & Run Torque Note 5 94
45 Piggable N/A 95 Requisition Number Note 5
46 Fail Position Fail Close (FC) 96
47 Identification Plate Note 1 97
PURCHASE
48 Weight Note 5 98
49 Control Scheme Note 5 99
50 Block & Bleed N/A 100

NOTES :
1. Instruments shall have attached SS name plate which is hard stamped or engraved with tag number.
2. All exhaust port shall be provided with bug screen 316 SS.
3. The actuator shall be sized for 130% of the required valve reset/break torque at site maximum differential pressure as applicable.
4. As per COPI Pre-Approved Manufacturers-Fabricators List, ID-G-BU-GG0-AML-GN-00-0001 latest revision.
5. VTA = vendor to advise.
6. Valves shall be as per API 6D, fire tested as per API 6FA or API 607, and hydrotested as per API 598 or ISO 5208
7. All electronic components shall be explosion proof type suitable for area classification and certified by authorities body.
8. Flange facing & finish shall be as per ASME B16.5
9. Valve, actuator and accessories shall be painted as per Mfr Std, refer to Maintenance Coating Specification for Offshore and Onshore Facilities, ID-G-BU-DD3-STS-GN-98-0002.
10. Maximum sound level shall be 85 dBA at 3 feet distance from valve
11. All valves shall refer to COPI spec. Pipe, Valves and Fittings, ID-N-BU-LL0-STS-GN-00-0002 and all reference docs as indicated in General Notes.
12. Vendor shall submit torque table sizing to be checked and verified.
13. The instrument air pressure will have a normal pressure of 100 Psig. However actuators shall be capable of operating reliably with a supply pressure of 70 to 135 Psig.
14. Actuators shall be sized to allow closing stroking times not exceed 3 seconds plus 1 second for every 1" of valve body size.
15. Vendor shall test of hydrotest and gas test per code witness by purchaser, vendor shall provide enough notification of testing witnes
16. Vendor shall re-test (as test per code) periods valve all testing at indonesian testing facilities witnees by manufacturer prior deliverid to site
 INSTRUMENT DATASHEET DOC. NO.:

ID-N-RW-JJ1-DSR-ST-87-3001
ON-OFF VALVES / SDV / BDV
Page : 20 of 21

PROJECT :
LTRO-1B LP COMPRESSOR PACKAGE RENTAL Issued for Use 2 19-Mar-20 PS ANR TU
PROJECT DESCRIPTION REV DATE BY CHK'D APPV'D
1 Tag No. 60-BDV-0002 51 Manufacturer Note 4

2 Service Outlet Fuel Gas Filter to Flare Header 52 Model Note 5

3 P & Id No. ID-N-RW-PP0-PID-ST-60-3002 53 Actuator Type Pneumatic Piston with Spring Return
4 GENERAL Line No. 2"-GF-60-0709-AA1 54 Acting Type Single Acting
5 Line Size / Wall Thickness / Pipe Id 2" 55 Spring Return Yes
6 Piping Class 150# - RF 56 Actuator Mechanism Scotch Yoke
7 Area Classification Class 1, Div 2, Group D 57 Operational Position Close
8 58 Air Failure Position Open
9 59 Air Supply Pressure Note 13
10 Process Fluid Fuel 60 Filter & Regulator Required 316SS
11 Fluid State Gas 61 Lubricator & Pneumatic Conn. Required 1/2" NPTF
12 Operating Temp. °F 100.9 62 Max. Degree of Rotation 90 degree
13 Operating Press. Psig 160 63 Orientation Paralel to line
14 PROCESS Max. Inlet Press. Psig 250 64 Mechanical Position Indicator Red Close / Green Open
15 DATA Max. Shut Off DP Psi 250 65 Limit Stop Required
16 Design Press. Psig 250 66 ACTUATOR Overload Protection Required
17 Design Temp. °F 150 67 Break & Run Torque Note 5
18 Predicted Sound Level dB 85 (Note.5) 68 End Torque Note 5
19 69 Opening & Closing Time Note 14
20 Manufacturer Note 4 70 Adjustable Stroking Time Note 5
21 Model No. Note 5 71 Valve DP for Sizing 250 Psi
22 Design Code API 6D 72 Actuator Test Pressure Required
23 Piping Valve Spec BA-AA-3-2 73 Man. Override / Hand Wheel N/A
24 Valve Type Ball 74 Valve Control Station Set Required
25 Type Of Body Ball 3 Piece Body 75 Fire Safe N/A
26 Body Size Port Size 2" Full Bore 76 Paint & Finish Note 9, Red (RAL 3002)
27 Configuration Bonnet Trunnion Bolted 77 Air Consumption Note 5
28 Max. Degree Of Rotation 90 degree 78 Identification Plate Note 1
29 Fire Safe Design Yes API 6FA 79 IAS Operating Pressure 120 Psig
30 End Connection Size & Rating 2"-150#, RF 80 Tubing / Fitting Material 316SS
31 End Connection Type Flange RF (Note 8) 81 Partial Stroke Facility Yes (Local)
32 Body & Bonnet Material ASTM A105 82 Actuator Material Note 5
33 Ball / Disc Material ASTM A182 GR F316 83 Tag No. Open Position 60-ZSO-0002
34 Stem Material ASTM A276 F316 84 Tag No. Close Position 60-ZSC-0002
35 Seat Material ASTM A182 GR F316 85 Cable Entry Size 3/4" NPTF
SWITCHES
36 Seat Ring Material Note 5 86 Contact Config. / Rating SPDT, 24 VDC, 1 A
37 VALVE Seat Insert Material Filled TFE (Note 5) 87 Limit Switch Type 2ea Hermetically Sealed, Dry Contact
38 Seal Material Filled TFE (Note 5) 88
39 Packing Material Filled TFE 89 Tag No. 60-SOV-0002
ASTM A193 GR B7M Hot Dip Spun
40 Bonnet Bolts Material 90 Cable Entry Size 1/2" NPTF
Galvanized
ASTM A194 GR 2HM Hot Dip Spun
41 Bonnet Nuts Material 91 SOLENOID Solenoid Type / Material 3 Way Valve / 316 SS
Galvanized
Replaceable Ball & Seat, Anti Static VALVE
42 Ball & Seat Design Seat Ring, Side Entry, 92 Manual Reset Yes
Anti Blow Out Stem
43 Leakage Class Class VI ANSI FCI 70.2 93 Degree of Protection Explosion Proof Eex'd'
44 Break & Run Torque Note 5 94
45 Piggable N/A 95 Requisition Number Note 5
46 Fail Position Fail Open (FO) 96
47 Identification Plate Note 1 97
PURCHASE
48 Weight Note 5 98
49 Control Scheme Note 5 99
50 Block & Bleed N/A 100

NOTES :
1. Instruments shall have attached SS name plate which is hard stamped or engraved with tag number.
2. All exhaust port shall be provided with bug screen 316 SS.
3. The actuator shall be sized for 130% of the required valve reset/break torque at site maximum differential pressure as applicable.
4. As per COPI Pre-Approved Manufacturers-Fabricators List, ID-G-BU-GG0-AML-GN-00-0001 latest revision.
5. VTA = vendor to advise.
6. Valves shall be as per API 6D, fire tested as per API 6FA or API 607, and hydrotested as per API 598 or ISO 5208
7. All electronic components shall be explosion proof type suitable for area classification and certified by authorities body.
8. Flange facing & finish shall be as per ASME B16.5
9. Valve, actuator and accessories shall be painted as per Mfr Std, refer to Maintenance Coating Specification for Offshore and Onshore Facilities, ID-G-BU-DD3-STS-GN-98-0002.
10. Maximum sound level shall be 85 dBA at 3 feet distance from valve
11. All valves shall refer to COPI spec. Pipe, Valves and Fittings, ID-N-BU-LL0-STS-GN-00-0002 and all reference docs as indicated in General Notes.
12. Vendor shall submit torque table sizing to be checked and verified.
13. The instrument air pressure will have a normal pressure of 100 Psig. However actuators shall be capable of operating reliably with a supply pressure of 70 to 135 Psig.
14. Actuators shall be sized to allow closing stroking times not exceed 3 seconds plus 1 second for every 1" of valve body size.
15. Vendor shall test of hydrotest and gas test per code witness by purchaser, vendor shall provide enough notification of testing witnes
16. Vendor shall re-test (as test per code) periods valve all testing at indonesian testing facilities witnees by manufacturer prior deliverid to site
 INSTRUMENT DATASHEET DOC. NO.:

ID-N-RW-JJ1-DSR-ST-87-3001
ON-OFF VALVES / SDV / BDV
Page : 21 of 21

PROJECT :
LTRO-1B LP COMPRESSOR PACKAGE RENTAL Issued for Use 2 19-Mar-20 PS ANR TU
PROJECT DESCRIPTION REV DATE BY CHK'D APPV'D

VALVE ARRANGGEMENT

1. SHUTDOWN VALVE WITH PARTIAL STROKE 2. SHUTDOWN VALVE W/O PARTIAL STROKE

3. BLOWDOWN VALVE WITH PARTIAL STROKE