Customer Standards Required For Reference
Customer Standards Required For Reference
Customer Standards Required For Reference
General Motors
Daimler Chrysler
PS-9336<H>
PS-10125<T>
AS-10119<A>
Packaging shipping and labelling
PSFD0270 Prism
PF-SAFETY<S>
PF-Emissions<E>
PS-7300 The Diamond
PF-8500 Product validation
Ford
Statement of Work
WSS-M99P9999-A1 (PPAP)
VDS
SDS
MP&L
Global Craftsmanship
VOPQUN-008 (8d)
Customer Specific Requirements Grid
TS16949 STD # FORD Reqmt GM Reqmnt Daimler/Chrysler Visteon Compliance Reference
5.6 Mgmnt Review Using summarized QOS data for At least once per year No requirement Same as FORD
Mgmt review outline - need not
be one meeting
include Q-1 assessment results
6.3.2 Contingency Notification of Buyer and STA No requirement No requirement Documented Plan per
engineer, and Assembly plant website, plus notification
within 24 hours within 24 hours
7.1 Product Meet requirements of See GM publications Use PAP method APQP status report
Realization Planning "Statement of Work" using Visteon form
Report APQP status as defined
in website
Use prototype data for production
planning
See table A & B
7.2.2.2 Feasibility Include all supplier and Ford no requirement no requirement Same as FORD
organizations as appropriate "Should" do feasibility
20% volume increase requires
full feasibility study
7.3.1.1, 7.3.3.2 Family parts may be covered by No requirement Need CP for all three build Similar to FORD but less
FMEAs, Control Plns one FMEA or CONTROL PLAN phases. stringent
This must be approved by FORD * several shalls that may
STA (Ford 4.2) need attention
emphasis on prevention
2
Communication through Global Supplier Portal
3
7.3.2.3 Special Critical and Special Ref GM 1805 "shall be knowledgeable If no SCs are identified then
Characteristics characteristics guidelines only Use GM KCDM of stds" PS-9336<H> plant must ID appropriate SCs
also 7.2.2.1 PS-10125<T>, AS-10119<A> per Visteon procedure
Ref: The Diamond <> 4.2.1.5
7.3.4, 7.3.6.1 Must use FPDS for review of No requirement All design changes Same as Ford
Design design and development stages must have written approval
prior to implementation
7.3.5 Design must perform verification to No requirement must be performed Same as Ford
Verification compare with VDS and SDS before PSO can be completed Verification methods shall be
Continuing conformance
inspection/test shall be
performed during the model
year.
7.3.7 Design No requirement All changes shall have All changes shall have No requirement
Changes written approval or waiver written approval or waiver
7.3.6.3 PPAPs 1) Shall comply with AIAG PPAP Same as Ford Same as Ford Same as Ford
process PPAP's required
2)Subcontractors must meet PPAP from suppliers Same as Ford
requirements
3) All design changes shall have All proposed changes
approval per PPAP and made shall be submitted to Visteon for
through WERS or SREA process approval prior to implementation.
4) Run-at-rate is satisfied by PPAP level determined by
demonstrating "Prod. Verification" Visteon's report Card system
5) PPAP shall be reviewed yearly
PSW's re-issued after this review
7.4.3.1 Incoming Need incoming metrics unless Ref: GM 1746 No ref Metrics to be used as key
Product Quality waived in writing by STA indicator of subcon management
Any inspection should be When sampling plans are used, sample
sufficient for the risk and impact sizes consistant with 90% confidence
to the OE and 0 defect acceptance criteria
7.5.1.3 Job set Set up records shall be No ref No ref Same as Ford
ups maintained for 1 year. Note: includes manual tooling
exchanges
4
7.5.2
Process Validation No requirement No requirement PSO shall be completed by No requirement
product team to verify readiness
prior to PPAP submittal.
Parts that have been out of
production for 12 months or more
shall have production led PSO
7.5.3, 7.5.4, 7.5.5 shall meet requirements Ref: GM 1731 shall conform to Use AIAG MMOG
7.5.5.1 specified by Fords MP&L DC Packing, shipping and
Ref 4.340 Cust Specifics labelling instructions
7.6.1. MSA Family gauge studies must No ref No ref Record retention for life
be approved by STA of part plus 10 years.
8.2.2 Internal Either train auditors in new Should be aware of Perform at least once per year Internal audits must be
Audits standard or have completed core tools, customer performed by 3rd party
5 internal audits in the company specifics if no lead auditor available on site
of a trained auditor covering all
aspects relating to Ford
Process and product audits
can be performed by process
specialists without full auditor
training.
8.2.4, 8.3.4 ES test failures shall stop no requirement No requirement Develop plan to meet ES
Monitoring and shipments. Ford shall be informed test requirements and
measuring of product All suspect must be reworked. include in PPAP.
Test frequency requirements Reaction plans to failures
shall be noted in the control plan must be included in the IP
and FMEA test plan.
Revisions to frequencies need
STA approval
8.3,8.5.2,8.5.3 Ref : Ford 8d and VOPQUN-008 ref: GM 1920 A written 7 step plan Ref: Visteon
Control of NC Internal notification system shall be submitted for management of
product and correctve Communicate results and PPM's corrective action quality spills process
action Implement corrective actions PRISM - at least two people at
each loc. must be trained in use
and reg. access the system
PSFD0270 to be incorporated
to effectively respond to PRISM
issues
5
NEW REQUIREMENTS IN TS16949
The following requirements are a new addition or significantly different from QS9000
5.1.1 Process Efficiency Top management shall review the product realization process
and supporting processes to ensure effectiveness and efficiency
5.4.1 Quality Objectives To ensure objectives are set including those relating to product
To ensure they are measurable, achievable in the time frame and
address customer expectation
5.5.2.1 Customer Rep To ensure quality objectives are set including SC's, objectives
training, corrective action, preventive action and design and
development.
6.2.2.4 Motivation and Need process for motivating employees to achieve quality objectives,
Empowerment to make continual improvement and create an environment for
innovation
To include technical and quality awareness
Need process to measure the extent to which personnel are aware
of their relevance and importance and how they contribute to
the objectives
6.3 Infrastructure Ensure buildings and equipment are in good working order
7.3.2.1 Product design ID, document and review customer requirements, use of info e.g.
input field data, prototype data, historical data and targets for lifespan,
durability, cost etc
7.3.2.2 Manufacturing ID, document and review design output data, targets for productivity,
process design input capability and cost and experience from previous developments
6
TS 16949 reference Statement
7.3.3.2 Manufacturing Needs to match MPD input (see above) to allow verification
process design output To include specs, drawings, flows, FMEA, CP, WI's, quality
measurables, error proofing, rapid detection and feedback of
NC's
7.4.3.2 Supplier Monitor delivered product quality, customer disruptions and delivery
Monitoring performance including premium freight
8.2.2.5 Internal auditor Auditors must be qualified to audit the latest TS standard
qualifications
8.5.1.2 Manufacturing Continually focus on control and reduction of variation in product and
Process Improvement processes.
Note - Processes must be capable, stable and meeting
customer requirements before continual improvement can be
instigated