Power You Can Depend On: Introduction - Impact Wrenches
Power You Can Depend On: Introduction - Impact Wrenches
Power You Can Depend On: Introduction - Impact Wrenches
LTS
The LTS models cover a recommended
torque range of 22-650 Nm.
Place the tool on the joint to be fas-
tened and press the trigger. The tool will
shut-off automatically at a predetermined
Impact Wrenches
M6 M8 M10 M12 M14 M16 M18 M20 M22 M24 M27 M30 M36 M42 M45 M48
Nm 9.8 24 47 81 128 197 275 385 518 665 961 1310 2280 3640 4510 5450
LMS LMS06 LMS17 LMS17 LMS27 LMS37 LMS37 LMS47 LMS57 LMS57 LMS61 LMS61 LMS67 LMS86 LMS86 LMS86 LMS86
LMS06 LMS17 LMS27 LMS37 LMS37 LMS47 LMS57 LMS57 LMS57 LMS67 LMS67 LMS67 LMS86
8.8
M6 M8 M10 M12 M14 M16 M18 M20 M22 M24 M27 M30 M36 M42 M45
Nm 14 33 65 114 181 277 386 541 728 935 1350 1840 3210 5110 6340
LMS LMS06 LMS17 LMS27 LMS27 LMS37 LMS37 LMS47 LMS57 LMS61 LMS61 LMS67 LMS86 LMS86 LMS86 LMS86
LMS17 LMS17 LMS27 LMS37 LMS47 LMS47 LMS57 LMS61 LMS67 LMS67 LMS86
10.9
M6 M8 M10 M12 M14 M16 M18 M20 M22 M24 M27 M30 M36 M42
Nm 17 40 79 136 217 333 463 649 874 1120 1620 2210 3850 6140
LMS LMS06 LMS17 LMS27 LMS27 LMS37 LMS47 LMS57 LMS61 LMS61 LMS67 LMS86 LMS86 LMS86 LMS86
LMS17 LMS17 LMS27 LMS37 LMS47 LMS57 LMS61 LMS67 LMS67 LMS86
12.9
LTS LTS17 LTS17 LTS27 LTS37 LTS57 LTS57
LTS17 LTS27 LTS37 LTS37 LTS57 LTS57
= HEAVY DUTY
The torque figures are normal tightening torque for untreated oil-smeared and rust-protected bolts and nuts
= EXTRA HEAVY DUTY in the most common strength grades. The torque figures correspond to approximately 63% of tensile stress.
Impact Wrenches
LTS models
l Recommended operating range
22-650 Nm.
l Fast tightening and disassembly.
l Negligible reaction force.
l Low weight.
l High power-to-weight ratio.
l Tightening time should not exceed
5 seconds, to avoid excess wear on
the tool.
l Automatic shut-off shortens tightening
time.
l Consistent torque accuracy.
l No over-torquing.
l Adjustable torque setting.
l LTS17 and LTS 27 are lubrication free.
l LTS17 and LTS27 – Torsion bar principle.
l LTS27 HR43 – Quick change chuck for
separate torsion bars.
l LTS37 and LTS57 – Added bounce en-
ergy principle.
LMS models
l Recommended operating range
7-1800 Nm.
l Fast tightening and disassembly.
l Negligible reaction force.
l Low weight.
l High power-to-weight ratio.
l Tightening time should not exceed 5
seconds, to avoid excess wear on the
tool.
l Soft-start throttle.
l LMS06 – LMS27 are lubrication-free.
LMS models
l Recommended operating range
7-5000 Nm.
l Fast tightening and disassembly.
l Negligible reaction force.
l Low weight.
l High power-to-weight ratio.
l Soft-start throttle.
l Tightening time should not exceed 5
seconds, to avoid excess wear on the
tool.
Impact Wrenches
Accessories Included
LTS LMS
Silenced air exhaust through handle Silenced air exhaust through handle
Hose fitting (LMS47/57/61)
Torsion bar No. 06 LTS27 HR43 Hose fitting
Adjusting key LTS17 and LTS27
Optional Accessories
Protective covers
Exhaust kit
Tool holder with square drive, for 7/16" quick change chuck
Impact Wrenches
Optional Accessories
Suspension yokes
Horizontal Vertical Swivelling
Model Ordering No. Ordering No. Ordering No.
LMS06 HR – – 4210 0243 00
LMS17 – – 4250 1365 00
LMS27 4250 0872 00 4250 1159 00 –
LMS37 4250 0872 00 4250 1058 00 –
LMS47 4250 0872 00 4250 1327 00 –
Swivelling LMS57 4250 0872 00 4250 1160 00 –
LMS61 4250 0872 00 4250 1620 90 –
LMS67 4250 0677 80 – –
LMS86 0371 1102 00 – –
LTS17 – – 4250 1365 00
LTS27 4250 0872 00 – 4250 1365 00
LTS37 4250 0872 00 – 4250 1253 00
LTS57 4250 0872 00 – 4250 2229 00
Extended anvils
Vertical
Drive size Extension
Model in mm Ordering No.
Extended square drive anvil
LMS17 1/2 75 4250 1147 80ab
LMS27 1/2 75 4250 1085 80ab
LMS27 1/2 150 4250 1086 80ab
LMS37/LTS37 1/2 75 4250 1031 80ab
LMS37/LTS37 1/2 150 4250 1032 80ab
LMS37/LTS37 5/8 75 4250 1034 80ab
LMS37/LTS37 5/8 150 4250 1035 80ab
LMS47/LTS47 3/4 75 4250 1208 00
LMS47/LTS47 3/4 150 4250 1209 00
LMS57/LTS57 3/4 75 4250 1109 00
Horizontal LMS57/LTS57 3/4 150 4250 1110 00
LMS57/LTS57 3/4 200 4250 1111 00
LMS57/LTS57 1 75 4250 1113 00
LMS57/LTS57 1 150 4250 1114 00
Spline type anvil
LMS67 1 5/8‑14 – 4250 2473 80
Heavy duty anvil (thru hole)
LMS37/LTS37 1/2 80 4250 1041 01
Torsion bars
Torque
Torsion bar No. Nm Ordering No. Colour of bar
02 60 4250 1230 82 orange
03 75 4250 1230 83 yellow
04 90 4250 1230 84 green
05 100 4250 1230 85 blue
06 115 4250 1230 86 red (standard)
07 125 4250 1230 87 orange
08 140 4250 1230 88 yellow
09 150 4250 1230 89 green
10 165 4250 1230 90 blue
Installation Proposals
Service Kits