DOWSIL™ 795 Structural Glazing Sealant Technical Data Sheet
DOWSIL™ 795 Structural Glazing Sealant Technical Data Sheet
DOWSIL™ 795 Structural Glazing Sealant Technical Data Sheet
Typical Properties
Specification Writers: These values are not intended for use in preparing specifications.
2. Based on South Coast Air Quality Management District of California. Maximum VOC is listed both inclusive and
exclusive of water and exempt compounds. For a VOC data sheet for a specific sealant color, please send your
request to Dow.
Approvals/ DOWSIL™ 795 Structural Glazing Sealant meets the requirements of: ASTM Specification
Specifications C 1184 for structural silicone sealants ASTM Specification C 920, Class 50.
SGBP 2019-2721
How to Use When DOWSIL™ 795 Structural Glazing Sealant is used in structural applications the
structural joint design MUST be reviewed by a technical service specialist.
Complete design and installation guidelines are contained in the Asia Technical Manual,
and must be followed for warranty applications when using this product.
Joint Design Structural joints sealed with DOWSIL™ 795 Structural Glazing Sealant should have a
minimum depth (or bite) of 6 mm. For large site- glazed joints the sealant or bite should be
not more than 12 mm when the sealant can cure from one side only. When an open-cell
moisture-permeable spacer tape is used, a structural bite up to 24 mm can cure to optimum
strength. The exact structural bite should always be calculated. The thickness of the
structural sealant joint or glueline should be 6 mm minimum. As it must accommodate
thermal and dynamic movements the actual joint movements should be calculated. Ideally
the bite to glueline ratio should be not more than about 3:1.
Accessory The appropriate selection of all accessories such as setting blocks and backing materials is
Selection important to avoid discoloration or adhesion-related problems due to incompatibility. Dow
will also assess the suitability of proposed accessory materials as part of the standard
testing services. Silicone-based setting blocks are generally recommended for best
compatibility.
Preparatory Work Thoroughly clean all substrates to be sealed, removing all contaminants such as grease, oil,
dust, frost or water. All metal, glass, or other surfaces should be cleaned with the
recommended solvent, using a lint free cloth.
Method of Install backing material or joint filler, setting blocks, spacer shims and tapes. Mask areas
Application adjacent to joints to ensure neat sealant lines. Apply DOWSIL™ 795 Structural Glazing
Sealant in a continuous operation using positive pressure. (The sealant can be applied
using many types of air-operated guns and most types of bulk dispensing equipment.)
Before a skin forms (typically within 15 minutes), tool the sealant with light pressure to
spread the sealant against the backing material and joint surfaces. Remove masking tape
as soon as the bead is tooled.
Handling PRODUCT SAFETY INFORMATION REQUIRED FOR SAFE USE IS NOT INCLUDED IN
Precautions THIS DOCUMENT. BEFORE HANDLING, READ PRODUCT AND SAFETY DATA SHEETS
AND CONTAINER LABELS FOR SAFE USE, PHYSICAL AND HEALTH HAZARD
INFORMATION. THE SAFETY DATA SHEET IS AVAILABLE ON THE DOW WEBSITE AT
DOW.COM, OR FROM YOUR DOW SALES APPLICATION ENGINEER, OR
DISTRIBUTOR, OR BY CALLING DOW CUSTOMER SERVICE.
When stored at or below 27°C (80°F), DOWSIL™ 795 Structural Glazing Sealant has a shelf
life of 12 months from the date of manufacture. Refer to product packaging for “Use By
Date.”
Questions about the use of DOWSIL™ 795 Structural Glazing Sealant can be answered by
calling your local application sales engineer. Our laboratory personnel and technical service
staff are also available for assistance.
Packaging DOWSIL™ 795 Structural Glazing Sealant is supplied in 300 ml disposable plastic cartridges
Information and 600 ml foil sausages.
Limitations This product is neither tested nor represented as suitable for medical or pharmaceutical
uses.
DOWSIL™ 795 Structural Glazing Sealant should not be used for structural applications
without the prior written approval of the Construction Industry Technical Services
Department. Each project should be specifically and separately approved by Dow.
Dow shall not be held liable for any possible claims arising from structural glazing use of
DOWSIL™ 795 Structural Glazing Sealant for projects which have not been specifically
approved by Dow.
For projects which have been approved, Dow will issue a structural adhesion warranty on a
case by case basis at the user's request. It is the user's exclusive responsibility to ensure
project compliance with local building regulations.
Health and To support customers in their product safety needs, Dow has an extensive Product
Environmental Stewardship organization and a team of product safety and regulatory compliance specialists
available in each area.
Information
For further information, please see our website, dow.com or consult your local Dow
representative.
Dow’s sole warranty is that our products will meet the sales specifications in effect at the time of shipment.
Your exclusive remedy for breach of such warranty is limited to refund of purchase price or replacement of any product shown
to be other than as warranted.
TO THE FULLEST EXTENT PERMITTED BY APPLICABLE LAW, DOW SPECIFICALLY DISCLAIMS ANY OTHER
EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY.