SLL Glideloc Ladder Systems Emeauk Amp Aus PDF
SLL Glideloc Ladder Systems Emeauk Amp Aus PDF
SLL Glideloc Ladder Systems Emeauk Amp Aus PDF
Produktfamilj
Söll GlideLoc Vertical Height
Access System
The Söll GlideLoc® Safe Climbing system includes fall
protection ladders, guide rails, and guided type fall
arresters. System accessories such as entry and exit
devices, roof ascent or shaft entry equipment make it
possible to design a system that is not only appropriate
for the structure of the building or installation, but which
also satisfies the very highest safety requirements.
Sida 1 av 17
© Honeywell International Inc.
Söll GlideLoc Ladder Systems EMEA/UK & AUS
26026 / 1030291 Bottom/Top End Stop, breaking load 12kN for aluminium
ladders
For profile 52x51 mm, made of stainless steel; prevent the fall arrester
from being inserted incorrectly or accidentally slipping out of the guide
rail; supply of all fixings possible
26027 / 1030292 Bottom/Top End Stop, breaking load 12kN for steel/stainless
steel ladder and aluminium guide rail
Same specifications as bottom/top end stop with ref. 26026, however
for steel ladders and aluminium guide rail with profile 52x33mm,
50x32mm
Sida 2 av 17
© Honeywell International Inc.
Söll GlideLoc Ladder Systems EMEA/UK & AUS
23722 / 1027731 Folding footrest - galvanised steel- for Y-spar and twin
ladders
Complies with DIN 18799; for Y-spar and twin ladders with step
widths of 150 and 180 mm; rung distance: 280 mm; recommended
mounting distance: 10 m; complete with all mounting elements
Sida 3 av 17
© Honeywell International Inc.
Söll GlideLoc Ladder Systems EMEA/UK & AUS
26503 Folding footrest - stainless steel - for Y-spar and twin ladders
Same specifications as the folding footrest with ref. 23722, however
in stainless steel.
21516 / 1028004 Footrest with hinge on left side - galvanised steel for
GlideLoc guide rails
Pivotable; for mounting on side rails with a width of max. 50 mm;
complete with all mounting elements
21520 / 1028006 Footrest with hinge on right side - galvanised steel for
GlideLoc guide rails
Pivotable; for mounting on side rails with a width of max. 50 mm;
complete with all mounting elements
Sida 4 av 17
© Honeywell International Inc.
Söll GlideLoc Ladder Systems EMEA/UK & AUS
10550 / 1027738 Exit section - aluminium - for Y-spar and twin ladders
To be installed within the climbway; to remove or insert the fall
arrester; comes with single-use mounting tool; Attention: installation is
only possible between two rungs
10558 / 1007114 Rotary exit section with footrest -aluminium - for aluminium
ladders
Same specifications as rotary exit section ref. 21814, however with
footrest that has two individually foldable platforms
Sida 5 av 17
© Honeywell International Inc.
Söll GlideLoc Ladder Systems EMEA/UK & AUS
23144 / 1027741 Pivoting roof exit with hinge on left side - galvanised steel -
for aluminium ladders
To be used in confined spaces; used for leaving or entering the ladder
system safely onto or from the platform behind the ladder; complete
with all mounting elements; to be fixed on the central spar of the
ladder; top ladder section must be at least 1400 mm long
24946 Pivoting roof exit with hinge on right side - galvanised steel -
for aluminium ladders
Same specifications as pivoting roof exit with ref. 23144, however
with hinge on the right side
23312 / 1027939 Pivoting roof exit with hinge on left side - galvanised steel -
for steel/stainless steel ladders
Same specifications as pivoting roof exit with ref. 23144, however for
steel/stainless steel ladders
26772 Pivoting roof exit with hinge on right side - galvanised steel -
for steel/stainless steel ladders
Same specifications as pivoting roof exit with ref. 23312, however
with hinge on the right side
21683 / 1027742 Aluminium cover plate with hinge on left side - for Y-spar and
twin ladders
Without ladder section; prevents unauthorised people from climbing the
front or the rear of the ladder; brackets are covered as well (up to
projection 150 mm); opens laterally; hinges can be switched on site;
stainless steel fixings; cylinder lock; plate length: 2500 mm; width: 523
mm; width when cover plate is open: 991 mm; factory assembly on a
ladder section (16368 / 1027744); replacement key (17478 / 1027745);
installation above normal height - Hinge on left side (21684 / 1027746);
installation above normal height - Hinge on right side (21685 / 1027747)
21759 / 1027743 Aluminium cover plate with hinge on right side - for Y-spar
and twin ladders
Same specifications as aluminium cover plate with ref. 21683,
however with hinge on right side
21684 / 1027746 Aluminium cover plate installed above normal height with
hinge on left side - for Y-spar and twin ladders
Same specifications as aluminium cover plate with ref. 21683,
however with installation above normal height
21685 / 1027747 Aluminium cover plate installed above normal height with
hinge on right side - for Y-spar and twin ladders
Same specifications as aluminium cover plate with ref. 21684,
however with hinge on right side
11354 / 1007740 Steel cover plate - for aluminium ladders with step width 150
mm
Without ladder section; prevents unauthorised people from climbing the
ladder; can be mounted and must be secured with a padlock; length:
2000 mm
Sida 6 av 17
© Honeywell International Inc.
Söll GlideLoc Ladder Systems EMEA/UK & AUS
15299 / 1027750 Turntable with bending radius of horizontal guide rail > 1000
mm - stainless steel - for aluminium ladders
For safe transfer from vertical to horizontal and vice versa; with
aluminium profile for supporting the fall arrester; factory assembly on
an aluminium Y-spar ladder (16884 / 1027752)
20793 / 1027751 Turntable with bending radius of horizontal guide rail < 1000
mm - stainless steel - for aluminium ladders
Same specifications as the turntable with ref. 15299, however with
bending radius < 1000mm
11607 / 1027932 Turntable with bending radius of horizontal guide rail > 1000
mm - stainless steel - for steel/stainless steel ladders
Same specifications as the turntable with ref. 15299, however for
steel/stainless steel ladders
20349 / 1028007 Turntable with bending radius of horizontal guide rail < 1000
mm - stainless steel - for steel/stainless steel ladders
Same specifications as the turntable with ref. 11607, however with
bending radius < 1000mm
16191 / 1014666 Lower part for manhole entry device - stainless steel
Fixed to the rear of the fixed guide rail; for both aluminium and
stainless steel manhole entry devices
Sida 7 av 17
© Honeywell International Inc.
Söll GlideLoc Ladder Systems EMEA/UK & AUS
10779 / 1027814 Mounting bracket with insertion aid for projection: 130 mm -
galvanised steel
For use in mast clamp without lock (BES-OA); complete with mounting
elements for fixing to ladder
14981 / 1027815 Bracket for mast clamp with lock - projection: 130 mm -
galvanised steel
For use in mast clamp with lock (BES-MA); complete with mounting
elements for fixing to ladder
Sida 8 av 17
© Honeywell International Inc.
Söll GlideLoc Ladder Systems EMEA/UK & AUS
14982 / 1027816 Bracket for mast clamp without lock - projection: 130 mm -
galvanised steel
For use in mast clamp without lock (BES-OA); complete with mounting
elements for fixing to ladder
18068 Bracket for mast clamp without lock - projection: 150 mm-
galvanised steel
For use in mast clamp without lock (BES-OA); complete with mounting
elements for fixing to ladder; projection: 130 mm (14982 / 1027816);
projection: 150 mm (18068)
Sida 9 av 17
© Honeywell International Inc.
Söll GlideLoc Ladder Systems EMEA/UK & AUS
11025 / 1027720 Angle corner mounting bracket for use on corner struts with
angle profile up to 100 x 100 - galvanised steel
For use on corner struts of lattice masts with angle profile; complete
with all mounting elements; support structure must be checked to
ensure sufficient strength; for use on corner struts with angle profile
up to 100 x 100 (11025 / 1027720); for use on corner struts with angle
profile from 110 x 110 to 140 x 140 (14696 / 1027721); for use on
corner struts with angle profile from 150 x 150 to 180 x 180 (14698 /
1027722); for use on corner struts with angle profile from 190 x 190
to 220 x 220 (14699 / 1027723); for use on corner struts with angle
profile from 230 x 230 to 260 x 260 (14700 / 1027724)
14696 / 1027721 Angle corner mounting bracket for use on corner struts with
angle profile from 110 x 110 to 140 x 140 - galvanised steel
Same specifications as angle corner mounting bracket ref. 11025,
however for use on corner struts with angle profile from 110 x 110 to
140 x 140
14698 / 1027722 Angle corner mounting bracket for use on corner struts with
angle profile from 150 x 150 to 180 x 180 - galvanised steel
Same specifications as angle corner mounting bracket ref. 11025,
however for use on corner struts with angle profile from 150 x 150 to
180 x 180
14699 / 1027723 Angle corner mounting bracket for use on corner struts with
angle profile from 190 x 190 to 220 x 220 - galvanised steel
Same specifications as angle corner mounting bracket ref. 11025,
however for use on corner struts with angle profile from 190 x 190 to
220 x 220
14700 / 1027724 Angle corner mounting bracket for use on corner struts with
angle profile from 230 x 230 to 260 x 260 - galvanised steel
Same specifications as angle corner mounting bracket ref. 11025,
however for use on corner struts with angle profile from 230 x 230 to
260 x 260
Sida 10 av 17
© Honeywell International Inc.
Söll GlideLoc Ladder Systems EMEA/UK & AUS
12732 / 1027894 Weld-on bracket for steel/stainless steel ladders - raw steel
To be welded on site; projection 150 mm; complete with all mounting
elements; ensure structure is suitable for welding
17988 / 1028025 Connector for steel and aluminium guide rails - stainless
steel
To connect guide rails; complete with all mounting elements; included in
the delivery of each guide rail
Sida 11 av 17
© Honeywell International Inc.
Söll GlideLoc Ladder Systems EMEA/UK & AUS
10903 / 1007735 Clamp with screw length M12 x 80 for rung diameter of 25
mm - galvanized steel
For retrofitting on ladders or step irons; complete with all mounting
elements; support structure end/or wall mounting must be checked to
ensure sufficient strength
14804 / 1013115 Clamp with screw length M12 x 90 for rung diameter 26-35mm
- galvanized steel
Same specifications as galvanized steel clamp with ref. 10903,
however with screw length M12 x 90 for rung diameter 26-35mm
14805 / 1027983 Clamp with screw length M12 x 100 for rung diameter
36-45mm - galvanized steel
Same specifications as galvanized steel clamp with ref. 10903,
however with screw length M12 x 100 for rung diameter 36-45mm
14806 / 1027985 Clamp with screw length M12 x 110 for rung diameter
46-55mm - galvanized steel
Same specifications as galvanized steel clamp with ref. 10903,
however with screw length M12 x 110 for rung diameter 46-55mm
14807 / 1007833 Clamp with screw length M12 x 120 for rung diameter
56-65mm - galvanized steel
Same specifications as galvanized steel clamp with ref. 10903,
however with screw length M12 x 120 for rung diameter 56-65mm
Sida 12 av 17
© Honeywell International Inc.
Söll GlideLoc Ladder Systems EMEA/UK & AUS
14809 / 1011313 Clamp with screw length M12 x 70 for rung diameter of 25
mm - stainless steel
For retrofitting on ladders or step irons; complete with all mounting
elements; support structure end/or wall mounting must be checked to
ensure sufficient strength
14813 / 1016091 Clamp with screw length M12 x 80 for rung diameter 26-35mm
- stainless steel
Same specifications as stainless steel clamp ref. 14809, however
with screw length M12 x 80 for rung diameter 26-35mm
14814 / 1027984 Clamp with screw length M12 x 90 for rung diameter 36-45mm
- stainless steel
Same specifications as stainless steel clamp ref. 14809, however
with screw length M12 x 90 for rung diameter 36-45mm
14815 / 1027986 Clamp with screw length M12 x 100 for rung diameter
46-55mm - stainless steel
Same specifications as stainless steel clamp ref. 14809, however
with screw length M12 x 100 for rung diameter 46-55mm
14816 / 1027987 Clamp with screw length M12 x 120 for rung diameter
56-70mm - stainless steel
Same specifications as stainless steel clamp ref. 14809, however
with screw length M12 x 120 for rung diameter 56-70mm
Sida 13 av 17
© Honeywell International Inc.
Söll GlideLoc Ladder Systems EMEA/UK & AUS
11319 / 1027992 Bracket for lateral mounting of guide rails on step irons -
galvanized steel
Only for step irons with a diameter of 20 to 25 mm; complete with all
mounting elements
17989 / 1027993 Bracket for lateral mounting of guide rails on step irons -
stainless steel
Only for step irons with a diameter of 20 to 25 mm; complete with all
mounting elements
Sida 14 av 17
© Honeywell International Inc.
Söll GlideLoc Ladder Systems EMEA/UK & AUS
Översikt
Viktigaste egenskaperna
Söll GlideLoc fall protection ladders have an integrated guide rail for the guided-type fall arrester in the centre stile.
They are available in aluminum, galvanized or stainless steel both as central-stile ladders (Y-spar) and with side stiles
(twin ladder).
Distance between rungs is 280mm. Customised designs may be available.
Durable construction for extended service life
Accommodates multiple workers
The easy-climb Söll GlideLoc guided type fall arrester offers hands-free safety at height that ultimately
increases worker mobility, safety and productivity.
Guided type fall arrester is fixed by the karabiner hook to the D-ring of the full body harness and inserted into the guide
rail
Engineered for smooth operation for ascending/descending, provides an easier, more comfortable climb
Automatic design – keeps both hands free for climbing
Stainless steel catch clamp – locks into the rail in the event of a fall
Integrated shock-absorbing mechanism – reduces force on the worker and system in the event of a fall
Fall indicator – alerts user to know when to remove the product from service
Sida 15 av 17
© Honeywell International Inc.
Söll GlideLoc Ladder Systems EMEA/UK & AUS
Integrated swivel, auto-locking carabiner connection – aids in trailing alignment and meets allowable attachment length
Design prevents up-side-down installation – increases worker safety by ensuring proper attachment
No requirement to lean back while climbing – reduces fatigue; ideal for ladder cages and confined spaces
Ergonomically designed for easy one-hand installation – increases productivity
Systems are available in easy-to-install kits or can be customized for your application with additional
available components, including:
Brackets for larger ladder rungs
Brackets to attach to ladder side rails
Foldable foot rests for long ladders
Shaft entry device to provide easy access to manholes and roof hatches
Ideal for:
Permanent Ladder Applications
Wind Power/Turbines
Telecommunications
Construction, buildings and facades
Utilities
Industrial Facilities / chimneys
Drilling Rigs/Platforms
Shipbuilding
Crane Installation
Confined Space
Loading bays
Föreskrifter
Meets the EN 353-1 and AS/NZS 1891 standards (and all applicable OSHA, ANSI and CSA standards)
Garantiinformation
We sincerely believe that our fall protection equipment is the best in the world. Our products endure rigorous test to ensure
that the fall protection equipment you trust is manufactured to the highest standards. Miller fall protection products are tested
to withstand normal wear and tear, but are not indestructible and can be damaged by misuse. Our Limited Lifetime Warranty
does not apply to normal wear and tear or abusive treatment of the product. In the unlikely event that you should discover
defects in either workmanship or materials, under our Limited Lifetime Warranty, we will repair or replace the product at our
expense. If a replacement is necessary and your product is no longer available, a comparable product will be substituted.
Should a product issue surface, contact us at +33 248 53 00 80 (Southern Europe) or +49 9281 8302 0 (Northern Europe).
Manufacturing specifications are subject to change without notice.
Specifikationer
Söll Comfort GlideLoc Fall Arrester
Attaches at top or bottom of rail
Söll Universal II GlideLoc Fall Arrester
Attaches anywhere on rail
Söll Comfort II GlideLoc Fall Arrester
Sida 16 av 17
© Honeywell International Inc.
Söll GlideLoc Ladder Systems EMEA/UK & AUS
Permanently installed climbing systems are tested and certified as a complete single system, including Söll guide rails, Söll
fall arresters and Söll accessories. This means that, in a Söll GlideLoc® system only the Söll GlideLoc® fall arresters may
be used. It is not permitted to use fall arresters from other manufacturers in these systems. Their use does comply with
the regulations, hence, their functionality can not be guaranteed and in the event of an accident, Honeywell will not be
liable.
Markings
The following is engraved on each Söll GlideLoc fall arrester:
Name of Manufacturer
Date of Manufacture and Serial number
CE-Label and Key-code of testing institute
Indication to read manual
Type of system
Relevant standard
Furthermore, an icon indicates to read the instruction manual before use. An arrow also indicates the correct direction
of use. The date plate indicates when the next inspection is due.
Ytterligare information
+33 248 53 00 80 (Southern Europe) or +49 9281 8302 0 (Northern Europe).
email: lignedevie.hsp@honeywell.com (Southern Europe) or info-soell.hsp@honeywell.com (Northern Europe)
Teknisk support
+33 248 53 00 80 (Southern Europe) or +49 9281 8302 0 (Northern Europe).
email: lignedevie.hsp@honeywell.com (Southern Europe) or info-soell.hsp@honeywell.com (Northern Europe)
Sida 17 av 17
© Honeywell International Inc.