Emufdd Eng
Emufdd Eng
Emufdd Eng
Connect the device as shown in the figure, the pin 1 of the flat is colored blue or red.
The power of the device usually 4 wires, 5 V should be connected as shown.
• EMUFDD is equipped with F-RAM memory, nonvolatile memory with 1014 cycles
of writing and reading, compared to 50 years of non stop hits.
MILO snc
SW & HW per automazione
Via Ruggiero Grieco 1/C 41011 Campogalliano -MO-
Codice Fiscale e P.IVA 03373570369
Tel. 059 528512 Fax. 059 520131 E-mail: info@milosrl.it Web: www.milosrl.it
EMUFDD_HW_MANUAL
3 Led ACCESS: indicates a request for writing or reading from the CNC or PC on
EMUFDD
4 Led OFF - LINE: must be on when you save or load on the USB
7 Button DOWN: to scroll the various directors on the stick (1 directory has the same
capacity of a floppy disk) to a maximum of 100 directors, several directors must have the
following suffix EMUFDDXX, so if you want to generate 100 directors the names of
directors must be EMUFDD00 up to EMUFDD99.
8 Button UP: to scroll the various directors on the stick to a maximum of 100, the
number of directors shall have the following suffix EMUFDDXX,
so if you want to generate 100 directors the names of directors must be EMUFDD00 up to
EMUFDD99.
9 Display: to see from loading the directors and / or to view the directory loaded on
EMUFDD
10 Connector: for USB stick
MILO snc
SW & HW per automazione
Via Ruggiero Grieco 1/C 41011 Campogalliano -MO-
Codice Fiscale e P.IVA 03373570369
Tel. 059 528512 Fax. 059 520131 E-mail: info@milosrl.it Web: www.milosrl.it
EMUFDD_HW_MANUAL
After connecting the device to the CNC or PC, check that the 'EMUFDD be seen from the CNC or
PC, try writing to the device if the device is not seen by the NC, one should try to configure it in
another way. Yellow LED on
Insert the USB key, press the button, load or save (this is to put EMUFDD in off-line) off-line red
LED is on, display shows CH and scans of several directors present on the stick. With the up
and down buttons to scroll through all 100 directors from 00 to 99, those on the key are
displayed on the display with two decimal points eg lit. 0.1. Now select the directory that you're
going to load and hold the LOAD button until the green LED lights up and load begins to flash
the yellow LED access. During this phase, the display shows LO, when they turn off the green
LED load to access the yellow and red LED off-line you can remove the keys, the display
alternately with the two segments, the number of directory loaded.
Insert the USB key, press the button, load or save (this is to put EMUFDD in off-line) off-line red
LED is on, display shows CH and scans of various directors present on the stick, finished
scanning the file appears on EMUFDD hold the SAVE button until the led flashes green and save
the yellow access. During this phase, the display shows SA, when they turn off the green light to
save the yellow and the red of access to off-line you can remove the keys, the display alternately
with the two segments, the number of directory loaded on EMUFDD.
MILO snc
SW & HW per automazione
Via Ruggiero Grieco 1/C 41011 Campogalliano -MO-
Codice Fiscale e P.IVA 03373570369
Tel. 059 528512 Fax. 059 520131 E-mail: info@milosrl.it Web: www.milosrl.it
EMUFDD_HW_MANUAL
• Create EMUFDD00, open the directory and copy the contents of the diskette
• Insert the USB stick in the emulator, set the 'emulator in off-line (red LED on), selected
with the UP and DOWN the directory to load; EMUFDD00 So in our case, the display will
show 0.0. hold the LOAD button until 'GREEN LED lights located above the LOAD button.
MILO snc
SW & HW per automazione
Via Ruggiero Grieco 1/C 41011 Campogalliano -MO-
Codice Fiscale e P.IVA 03373570369
Tel. 059 528512 Fax. 059 520131 E-mail: info@milosrl.it Web: www.milosrl.it
EMUFDD_HW_MANUAL
2 Release the buttons and use the UP and DOWN buttons to select the desired
configuration.
After selecting the configuration simultaneously press the SAVE + LOAD.
3 The emulator display cc and auto-reset (rapid flashing of all the LED ).
MILO snc
SW & HW per automazione
Via Ruggiero Grieco 1/C 41011 Campogalliano -MO-
Codice Fiscale e P.IVA 03373570369
Tel. 059 528512 Fax. 059 520131 E-mail: info@milosrl.it Web: www.milosrl.it