Uart Mcu

Using the UART in Microchip PIC18F
Microcontrollers
Corrado Santoro
ARSLAB - Autonomous and Robotic Systems Laboratory

Dipartimento di Matematica e Informatica - Università di Catania, Italy
santoro@dmi.unict.it
L.A.P. 1 Course
Corrado Santoro Using the UART in PIC18F Family

UART in MCUs
UART = Universal Asynchronous Receiver/Trasmitter

It is commonly referred as serial port
It is a peripheral for point-to-point communication between
two devices
Communication occurs in serial, i.e. one bit at time
Two communication PINs: RX and TX

UART trasmission basics
When no transmission, the line is set to Logical “1”
Then the software triggers the trasmission of a byte
(e.g. “C”, hexcode 43, binary 0100 0011
First a Logical “0” is transmitted, called start bit
Then the byte is transmitted LSB first
An additional parity bit may follow (not in the example); it
used for error checking
One or two stop bits (Logical “1”) ends the transmission

UART trasmission parameters
The following parameters must be set in the UART hardware:

transmission speed, in bps = Bit Per Second or baud
number of bits per character, usually 8
presence/absence of partity bit, usually absent
number of stop bits, usually 1
A setting 19200,8,N,1 means:

speed = 19200 bit-per-second;
bits = 8;
parity = None;
stop bits = 1.

UART in the PIC18F25K22
From the datasheet:

Two different UART
The TX line of the UART1 is shared with RC6
The RX line of the UART1 is shared with RC7
The TX line of the UART2 is shared with RB6
The RX line of the UART2 is shared with RB7
Basic registers per UARTx (“x” is the UART number):

TXSTAx, configuration of the transmitter
RCSTAx, configuration of the receiver
BAUDCONx, configuration of the baud rate (speed)
generator
SPBRGx, baud rate (speed) generator value

The Baud Rate Generator
It is divisor driven from system clock frequency (FOSC).

It is controlled by the following bits/registers:
SPBRGHx:SPBRGx: the divisor value to be applied to

FOSC to obtain the desired baud rate
BAUDCONxbits.BRG16, a bit which indicates whether the
divisor value uses 8 or 16 bits
TXSTAxbits.BRGH, a bit which indicates if we are using a
high-speed baud date
A formula exists to compute the divisor value, but... Microchip

provides very usefull tables!

Setting the Baudrate generator

Setting the UART
UART Setup
...
// setup UART
TRISCbits.TRISC6 = 0; // TX as output
TRISCbits.TRISC7 = 1; // RX as input
TXSTA1bits.SYNC = 0; // Async operation

TXSTA1bits.TX9 = 0; // No tx of 9th bit
TXSTA1bits.TXEN = 1 // Enable transmitter
RCSTA1bits.RX9 = 0; // No rx of 9th bit

RCSTA1bits.CREN = 1; // Enable receiver
RCSTA1bits.SPEN = 1; // Enable serial port
// Setting for 19200 BPS

BAUDCON1bits.BRG16 = 0; // Divisor at 8 bit
TXSTA1bits.BRGH = 0; // No high-speed baudrate
SPBRG1 = 51; // divisor value for 19200

The UART Transmitter
Transmission is triggered by loading the byte into TXREGx;

The byte is loaded into the shift-register and the TXxIF is set;
The byte is “shifted-out” (transmitted) and, when transmission is
completed TXSTAxbits.TRMT is set;
A new byte can be loaded into TXREG for a new transmission.
Transmitting a byte
Basic transmission
// wait the end of transmission
while (TXSTA1bits.TRMT == 0) {};
TXREG1 = new data; // start sending the new byte
... or, you can use directly the printf function, provided that you
implement a proper putch(char c) function, that is then called
by printf for each character to send.
Using printf
void putch(char c) {
// wait the end of transmission
while (TXSTA1bits.TRMT == 0) {};
TXREG1 = c; // send the new byte
}
...
printf("Hello world!!");
...

The UART Receiver
When a byte is received it is automatically loaded into RCREGx;

When reception is completed RCxIF is set, which can be tested (using
polling or interrupt);
Reading RCREGx causes RCxIF to be automatically reset;
But some errors may occur and must be handled:
Overrun error, RCSTAxbits.OERR==1, a new data is received
but RCREGx has not previously read;
Framing error, RCSTAxbits.FERR==1, the data is not properly
“framed”, i.e. the stop bit(s) are not valid.

Reading a character
UART Char Reading

char read char(void)
{
while (PIR1bits.RC1IF == 0) { // wait for char
if (RCSTA1bits.OERR == 1) {
RCSTA1bits.OERR = 0; // clear overrun if it occurs
RCSTA1bits.CREN = 0;
RCSTA1bits.CREN = 1;
}
}
return RCREG1;
}

Using the UART in Microchip PIC18F
Microcontrollers
Corrado Santoro
ARSLAB - Autonomous and Robotic Systems Laboratory

Dipartimento di Matematica e Informatica - Università di Catania, Italy
santoro@dmi.unict.it
L.A.P. 1 Course

Uart Mcu

Uploaded by

Copyright:

Available Formats

Uart Mcu

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Uart Mcu

Uploaded by

Copyright:

Available Formats

Using the UART in Microchip PIC18F

ARSLAB - Autonomous and Robotic Systems Laboratory

Corrado Santoro Using the UART in PIC18F Family

UART = Universal Asynchronous Receiver/Trasmitter

Corrado Santoro Using the UART in PIC18F Family

Corrado Santoro Using the UART in PIC18F Family

The following parameters must be set in the UART hardware:

A setting 19200,8,N,1 means:

Corrado Santoro Using the UART in PIC18F Family

From the datasheet:

Basic registers per UARTx (“x” is the UART number):

Corrado Santoro Using the UART in PIC18F Family

It is divisor driven from system clock frequency (FOSC).

SPBRGHx:SPBRGx: the divisor value to be applied to

A formula exists to compute the divisor value, but... Microchip

Corrado Santoro Using the UART in PIC18F Family

Corrado Santoro Using the UART in PIC18F Family

TXSTA1bits.SYNC = 0; // Async operation

RCSTA1bits.RX9 = 0; // No rx of 9th bit

// Setting for 19200 BPS

Corrado Santoro Using the UART in PIC18F Family

Transmission is triggered by loading the byte into TXREGx;

Corrado Santoro Using the UART in PIC18F Family

When a byte is received it is automatically loaded into RCREGx;

Corrado Santoro Using the UART in PIC18F Family

UART Char Reading

Corrado Santoro Using the UART in PIC18F Family

ARSLAB - Autonomous and Robotic Systems Laboratory

Corrado Santoro Using the UART in PIC18F Family

You might also like