Desk Power Plus U M English Manual 1000 1400 Tower
Desk Power Plus U M English Manual 1000 1400 Tower
Desk Power Plus U M English Manual 1000 1400 Tower
POWER PROTECTION
www.chloridepower.com
Cert No FM 10144
SAFETY NOTICES 7
SYSTEM DESCRIPTION
1) Front Panel 9
2) Back Panel 9
TROUBLE SHOOTING 14
SPECIFICATION 15
Safety Notices
- This UPS uses voltage that may be hazardous. Do not attempt to disassemble the unit.
The unit contains no user replaceable parts. Only factory service personnel may per
form repairs.
- Connection to any other type of receptacle other than a two-pole, three-wire grounded
receptacle may result in shock hazard as well as violate local electrical codes.
- In the event of an emergency, press the OFF button and disconnect the power cord
from the AC power supply to properly disable the UPS.
- Do not allow any liquids or any foreign object to enter the UPS. Do not place beverages
or any other liquid containing vessels on or near the unit.
- This unit intended for installation in a controlled environment (temperature controlled,
indoor area free of conductive contaminants). Avoid installing the UPS in locations
where there is standing or running water, or excessive humidity.
- Do not plug the UPS input into its own output.
UK
- Do not attach a power strip or surge suppressor to the UPS.
- Do not attach non-computer-related items, such as medical equipment, life-support
equipment, microwave ovens or vacuum cleaners to UPS.
- To reduce the risk of overheating the UPS, do not cover the UPS' cooling vents and
avoid exposing the unit to direct sunlight or installing the unit near heat
emitting appliances such as space heater or furnaces.
- Unplug the UPS prior to cleaning and do not use liquid or spray detergent.
- Do not dispose of batteries in a fire as they may explode.
- Do not open or mutilate the battery or batteries. Release electrolyte is harmful to the
skin and eyes. It may be toxic.
- A battery can present a risk of electrical shock and high short circuit current.
The following precautions should be observed when working on batteries:
1) Remove watches, rings, or other metal objects from the hands.
2) Use tools with insulated handles.
3) Do not lay tools or metal parts on top of batteries.
4) Disconnect charging source prior to connecting or disconnecting batteries terminal.
- Servicing of batteries should be performed or surpervised by Personnel knowledgeable
of batteries and the required precautions. Keep unauthorized personnel away from
batteries
- When replacing batteries , replace with the same number and type of sealed
lead-acid battery.
1) Front Panel
AC Mode:
Load Level LEDs
Fault LED Backup Mode:
Battery Capacity LEDs
AC Mode:
Green Lighting
Backup Mode:
Green Flashing Power “ON/OFF”
Switch
UK
2) Back Panel
Communication
Port
Cooling Fan
Modem/Phone Line
Surge Protection
AC Output
Circuit Breaker
AC Input
IEC
To install Desk Power Plus simply follow the instructions shown. Be aware that the Power
Switch must be kept in the “ON” position, otherwise, the UPS will be disabled and your
equipment will not be protected during a power failure.
3) Inspection
Remove the UPS from its package
and inspect it for any damage that
may have occurred during shipping.
If any damage is discovered, re-pack
the unit and return it to the place
of purchase.
UK
4) Placement
Install the UPS unit in any protected environment that provides adequate airflow around
the unit, and is free from excessive dust, corrosive fumes and conductive contaminants. Do
not operate your UPS in an environment where the ambient temperature or humidity is
high. iOn the other hand, place the UPS unit away from the monitor by at least 20cm to
avoid interference.
20 cm
5) Charging
This unit is shipped from the factory with its internal battery fully charged, however some
charge may be lost during shipping, and the battery should be recharged prior to use.
Plug the unit into an appropriate power supply and allow the UPS to charge fully by leaving
it plugged in for at least 8 hours.
8 hours
UK
6) Computer Connection
Connect one computer-related device into each of the power receptacles supplied on the
back of the UPS.
7) Modem/Phoneline Connection
Plug incoming internet line into the “In” socket at the back of the UPS .
Use on more internet line cable and plug one end of the internet line cable to the “Out”
socket at the back of the UPS.
Plug the other end of the modem input socket as shown below.
Incoming
Internet line
UK
8) Serial Cable Connection
To allow for unattended system shut down for your operating system, connect
the serial cable as per diagram below.
9) DC Start Function
DC Start Function enables
the UPS to be started up
when AC utility power is not
available and battery is fully
charged .
Just simply press the power
switch to turn on the UPS.
After removing the battery cover, gently extract the battery by disconnecting the
two wires connecting it to Desk Power Plus. Be sure to use the same type of
batteries and dispose the old battery properly at an appropriate recycling facility.