Issued: November 26, 2013

MATERIAL SAFETY DATA SHEET Revision No.: 01

IDENTIFICATION OF THE SUBSTANCE

Chemical Name: EPOXY PAINT

Chemical Family: EPOXY POLYAMIDE PAINT

Company Name: Berger Paints Pakistan Ltd.

Address: 36-Industrial Estate, Kot-Lakhpat, Lahore, 54000, Pakistan

Telephone Number: 00-92-423-5151545 ~ 548

Fax Number: 00-92-423-5151549

UAN: 042-111-237-437

COMPOSITION / INFORMATION ON INGREDIENTS

OCCUPATIONAL EXPOSURE
VAPOR
INGREDIENTS CAS No. WEIGHT % LIMITS
PRESSURE Pa
TLV (TWA) PEL (TWA)
Epoxy Resin 25036-25-3 25 ~ 35 % Not Est. Not Est. N/A
Melamine
Proprietary 03 ~ 07 % Not Est. Not Est. N/A
Formaldehyde
Pigments Proprietary 08 ~ 15 % Not Est. Not Est. N/A
Extenders Proprietary 30 ~ 40 % Not Est. Not Est. N/A
Xylene 1330-20-7 06 ~ 12 % 100 ppm 100 ppm 5.5 mml/gm
Solvent Naphtha
64742-94-6 12 ~ 18 % 300 ppm N/A N/A
(Aromatic)

HAZARD IDENTIFICATION

 Flammable. Heating may generate vapors which may form explosive vapor/ air mixtures. (H226)
 Toxic to Aquatic Organisms. May cause long term adverse effects on the aquatic
environment.(H412)
 Eye irritation. 2 (H319)
 May Cause Lungs and Stomach Damage If Swallowed
 Repeated exposure to skin may cause skin irritation/redness.2(H315)
 May cause Skin Allergic reaction (H317)

1
 Vapors may cause drowsiness and dizziness (H336)

FIRST AID MEASURES (SYMPTOMS)

Skin Contact: Prolonged or repeated skin contact may cause defatting of the skin leading to dermatitis.

Eye Contact: Irritation and redness in the eyes. If proper medical attention is not gained, may cause
permanent damage to eyes.

Ingestion: Nausea and stomach pain may occur. There may be vomiting and if proper medical attention
is not gained, permanent damage to stomach may occur.

Inhalation: Prolonged Inhalation of high levels of vapor may cause upper respiratory tract irritation.
Drowsiness or mental confusion may also occur. In severe cases, loss of consciousness may also occur.

FIRST AID MEASURES (ACTION)

Skin Contact: Wash the skin thoroughly with water, soap and some rough rubbing media (Wood dust
may be helpful) and remove contaminated clothing. Obtain medical attention if symptoms develop to
severity.

Eye Contact: Flush the eyes thoroughly with clean water for minimum 20 minutes whilst holding the eye
lids open and seek medical advice immediately.

Ingestion: Donot induce vomiting. Immediately rinse the mouth and drink plenty of water or milk. Get
prompt medical attention.

Inhalation: Remove the casualty from exposure to fresh air. If breathing has stopped, induce artificial
breathing. Keep the affected person warm and at rest. Get prompt medical attention.

FIRE FIGHTING MEASURES

Extinguishing Media: Water Spray, Carbon Dioxide, Polymer Foam, Dry Chemical powder

Exposure Hazards: Vapor may travel considerable distance to source of ignition and flash back. In
combustion, the material may emit toxic fumes, Carbon Dioxide/Carbon Monoxide

Protection for Fire Fighters: Wear self-contained breathing apparatus. Wear protective clothing to
prevent contact with skin and eyes.

ACCIDENTAL RELEASE MEASURES

2
Personal Precautions: Eliminate all sources of ignition. Mark out the contaminated area with signs and
prevent the access of unauthorized personnel.

Environmental Precautions: Donot discharge into drains or rivers. Contain the spillage using sufficient
appropriate absorbent material. Wood saw dust/sand is better to be used to collect the spilled material.

Clean-Up Procedure: Transfer to a closable, labeled salvage container for disposal by an appropriate
method.

HANDLING AND STORAGE

Handling Requirements: Ensure that there is sufficient ventilation of the area. Avoid direct contact with
the substance. Use Non-Sparking tools.

Storage conditions: Store in a cool, dry and well-ventilated area. Prevent the build-up of Electrostatic
Charge in the area.

EXPOSURE CONTROLS / PERSONAL PROTECTION

Workplace Exposure Limit: 100 ppm (08-Hours Exposure)

Engineering Measures: Ensure there is sufficient ventilation of the area.

Respiratory Protection: If workplace exposure limit, mentioned above exceeds, respiratory protection
may be required.

Hand Protection: Protective Gloves

Eye Protection: Safety goggles while handling or applying the product.

Skin Protection: Protective over-all.

PHYSICAL AND CHEMICAL PROPERTIES

Physical State: Viscous Liquid

Color: Red Oxide/ Grey

Odor: Mix Epoxy Aromatic Odor

Solubility In Water: Insoluble

Viscosity: 20 ~ 25 Sec @ Ford Cup # 4 (First 50 ml)

Boiling Point: NA

3
Flash Point: ≥ 20 oC

Auto-ignition Temperature: Above 400 oC

Specific Gravity / Relative Density: 1.43 ~ 1.53

STABILITY AND REACTIVITY

Stability: Stable under normal conditions

Conditions to Avoid: Spark, Naked Flame, Heat, Direct Sunlight

Material to Avoid: Strong Oxidizing Agents

TOXOLOGICAL INFORMATION

Routes of Exposure: Exposure to high levels of vapor may cause drowsiness, dizziness, nausea,
headaches, vomiting. Prolonged contact with skin may cause irritation leading to dermatitis in extreme
cases. Causes eye irritation and in severe cases, permanent damage to eyes.

ECOLOGICAL INFORMATION

Mobility: Floats on water

Hazard Nature: Harmful and dangerous for environment.

Persistence and Degradability: Inherently Biodegradable

DISPOSAL CONSIDERATIONS

Disposal Operation: Please contact local authorities and dispose-off according to local environment
regulations. Waste must be treated as “Controlled Waste”.

OTHER INFORMATION

Usage: Always use in accordance with manufacturer’s directions.

The above information is believed to be correct, as per current formulation and the information available at this time but
does not purport to be all inclusive and should be used only as a guide. Addition of solvents and reducers in this product will
substantially alter the composition and hazards of the product. Berger Paints Pakistan Ltd. does not hold the responsibility
for any type of damage resulting from handling or from contact with the above product.