Electromagnetic Induction
Electromagnetic Induction
Electromagnetic Induction
com
ELECTROMAGNETIC INDUCTION
Important Points:
1. The magnetic lines of force passing through a normal plane is called magnetic flux.
2. Faraday Laws:
a. Whenever there is changing in magnetic flux linked with a coil, emf is induced in it.
b. The induced emf is proportional to the negative rate of change of magnetic flux linked with
the coil.
dφ −dφ
e=− (Or) e=
dt dt
d ( Nφ )
For N turns e = − (Proportionality constant K = 1)
dt
d
e=− ( NBA) (Neumann’s Law)
dt
dφ (φ − φ )
c. Induced current (i) = e = − N = −N 2 2
dt t
− N (φ2 − φ2 )
d. Induced change (q ) = = (Induced charge is independent of time)
R
3. Lenz’s Law:
Induced emf always opposes the change that produces it. Lenz’s law obeys the law of
conservation of energy.
4. Motional EMF:
If a straight conductor of length l moves with a constant speed v perpendicular to the uniform
magnetic field of induction B, then a voltage is developed across ends of the conductor ends
which is given by e = Blv
e Blv
5. Induced current ( I ) = =
R R
www.sakshieducation.com
www.sakshieducation.com
6. Self Inductance:
If the current in a coil changes, the magnetic flux around the coil changes. Hence emf is
induced in the coil called self inductance.
If i is the current through the coil and f is the flux lines around the coil then
dφ di
e=− = −L
dt dt
8. Mutual Inductance:
a. When current in a coil changes, the magnetic flux linked with other coil changes and
an emf is induced in the secondary coil called mutual induction.
b. If IP is the current through the primary and fS is the flux linked with secondary,
φs ∝ I p ⇒ φs = MI p Where M is mutual inductance of the coil
www.sakshieducation.com
www.sakshieducation.com
5. What happens to the mechanical energy (of motion) when a conductor is moved in a
uniform magnetic field?
A. The mechanical energy spent in moving the conductor is converted into electrical energy and
then into thermal energy.
www.sakshieducation.com
www.sakshieducation.com
7. Define Inductance?
A. Inductance (L) is the ratio of the flux-linkage to current, it is equal to N Φ / I .
Units: Henry Dimensional formula: ML2T −2 A−2 .
A. The magnetic flux ( Nφ ) linked with the coil is found to be proportional to the strength of the
current (I)
i.e. N φ ∝ I ⇒ N φ = LI
Where constant of proportionality 'L' is called co-efficient of self induction (or) self inductance.
If I = 1A, N φ = L
Thus co-efficient of self induction of a coil is defined as the magnetic flux linked with a coil
through which a unit current flows.
www.sakshieducation.com
www.sakshieducation.com
1. Obtain an expression for the emf induced across a conductor which is moved in a
uniform magnetic field which is perpendicular to the plane of motion?
A. Consider a straight conductor moving in a uniform and time independent magnetic field.
Figure shows a rectangular conductor PQRS in which the conductor PQ is free to move.
The rod PQ is moved towards the left with a constant velocity as shown in the figure.
Assume that there is no loss of energy due to friction. PQRS forms a closed circuit enclosing
an area that changes as PQ moves. It is placed in a uniform magnetic field B which is
perpendicular to the plane of this system.
If the length RQ = x and RS =, the magnetic flux Φ B enclosed by the loop PQRS will be
Φ B = Blx
Since x is changing with time, the rate of change of flux will induce an emf given by:
−d Φ B d
ε= = − ( Blx )
dt dt
dx
= − Bt = Blυ
dt
Where we have used dx / dt = −υ which is the speed of the conductor PQ.
The induced emf Bl υ is called motional emf.
www.sakshieducation.com
www.sakshieducation.com
3. Obtain an expression for the mutual inductance of two long co-axial solenoids?
A. Mutual Inductance of Two Long Solenoids:
Consider two long co-axial solenoids s1 and s2, with s2 wound over s1.
Let l = Length of each solenoid
r1, r2 = radii of inner and outer solenoids
A = π r 12
= area of cross section of inner solenoids s1
N1,N2 = number of turns in the two solenoids
First we pass a time varying current I2 through S2. The magnet field set up inside S2 due to I2
is
B2 = µ o n 2 I 2
Where n2 =N2/l = the number of turns per unit length of S2.
Total magnetic flux linked with inner solenoid S1 is
φ 2 = B2AN1= µ on2I2.AN1
Mutual inductance of coil 1 with respect to coil 2 is
φ1 µ0 N1N 2 A
M12= = µ on2AN1=
I2 l
www.sakshieducation.com
www.sakshieducation.com
Now we consider the flux linked with the outer solenoid S2 due to the current I1 in the inner
solenoid S1. The field B1 due to I1 is constant inside S1 but zero in the annular region
between the two solenoids. Hence
B1 = µ o n 1 I 1
Where n1= N1/l = the no of turns per unit length of S1
Total flux linked with the outer solenoid S2 is
µo N1 N 2 AI1
φ 2 =B1AN2= µ on1I1.AN2=
l
∴Mutual inductance of coil 2 with respect to coil 1 is
φ2 µ0 N1N 2 A
M21== =
I1 l
Clearly M12=M21=M(say)
µo N1 N 2 A
M= = µ 0n1n2Al= µ 0n1n2 π r12l
l
Thus, the mutual inductance of two coils is the property of their combination. It does not
matter which one of them functions as the primary or the secondary coil.
www.sakshieducation.com
www.sakshieducation.com
1. Outline the path-breaking experiments of Faraday and Henry and highlight the
contributions of these experiments to our understanding of electromagnetism?
A. Whenever, there is a change in magnetic flux through a closed circuit, an induced emf is set up
in the circuit. This phenomenon is known as electromagnetic induction.
www.sakshieducation.com
www.sakshieducation.com
1) As shown in figure coil C1 is connected with galvanometer and coil C2 is connected with
battery.
2) When the coil C2 is moved towards or away from C1 , the galvanometer shows deflection
due to current is induced in coil C1 .
3) When the coil C2 is held fixed and C1 is moved, the galvanometer shows defection due to
current induced in coil C1 .
4) When two coils C1 and C2 are in relative motion that induces electric current.
III. Coil-Coil experiment - current induced by changing current:
1) Two coils C1 and C2 are held stationary. Coil C1 is connected to galvanometer G and coil
C2 is connected to a battery through a tapping key K.
2) First, the battery circuit is closed by pressing the tap key K, and then broken, the
galvanometer shows deflection in one direction and then in the other.
3) When the key K is kept pressed continuously, there is no deflection in the galvanometer.
4) The deflection is produced in the galvanometer only at make or break of the current in the
coil C1
www.sakshieducation.com
www.sakshieducation.com
2. Describe the working of a AC generator with the aid of a simple diagram and necessary
expressions?
A. AC Generator:
An electric generator or dynamo is a device which converts mechanical energy into electrical
energy. The simplest practical generator consists of a rectangular coil rotating in a uniform
magnetic field.
Description:
AC generator consists of coil mounted on a rotor shaft. The axis of rotation of the coil is
perpendicular to the direction of the magnetic field. The coil (armature) is rotated mechanically
in the magnetic field. The ends of the coil are connected to the external circuit by means of slip
rings and brushes.
Working:
When the coil rotates, the magnetic flux cutting the coil changes and hence emf is induced in it.
At any instant let the normal to the plane of the coil makes an angle with the field direction
where is the angular speed of the coil. The flux linked with the coil is given by, Where N is the
number of turns of the coil.
−dφ
But ε = = +BAN ω sin ωt
dt
∴ ε = ε m sin ωt
Where ε m = BAN ω is known as peak value of alternating emf
The direction of current changes periodically and hence the current is called alternating current.
Also, ε = ε m sin 2πυt
www.sakshieducation.com
www.sakshieducation.com
PROBLEMS
1. Predict the direction of induced current in the situation described by the following
figures:
According to Lenz’s law, the direction of induced current is always in such a way that it
opposes the cause due to which it is produced.
A. (a) Here, south pole is moving towards the coil, so according to Lenz’s law this end becomes
S-pole. (To oppose the motion of South Pole by repelling it). Hence, the direction of current
is clockwise (by using clock rule) and the current flows along p to q or qrpq.
(b) In coil p-q, at end q ⇒ S-pole is moving towards end q, so it behaves like a south pole (by
Lenz’s law). The direction of current is clockwise (by clock rule), i.e., from p to q or along
prq. North Pole is moving away so this end will behave like South pole (To oppose its away
motion by attracting it). In coil x-y, S-pole is induced (by Lenz’s law) and the direction of
current is clockwise i.e., x to y or along yzx.
(c) As the tapping key is just closed, the current in coil increases. So, the magnetic flux and
field increases. According to Maxwell’s right hand grip rule, the direction of magnetic field is
leftwards. Thus, the direction of induced current in the neighbouring coil is such that it try to
decrease the field, thus the direction of field in the neighbouring coil should be rightwards,
i.e., according to Maxwell’s right hand rule the direction of induced current is anticlockwise,
i.e., along xyz or yzx.
(d) As the Rheostat setting is changed, the current is changed. The direction of field due to the
coil is leftwards according to Maxwell’s right hand grip rule. The direction of induced current
in the left coil is such that the magnetic field produced by it in rightwards, thus the direction
of current in left coil is anticlockwise i.e., from zyx.
(e) As the key is just released, the current which is flowing anticlockwise goes on decreasing.
Thus, the induced current developed in such a sense the magnetic field due to left coil
increases (which is towards right). So, the magnetic field due to the right coil should also
towards right and hence the induced current is in anticlockwise, i.e., along xry.
(f) The magnetic field lines due to the current carrying wire are in the plane of the loop. Hence,
no induced current is produced in the loop (because no flux lines cross the area of loop).
www.sakshieducation.com
www.sakshieducation.com
2. Use Lenz’s law to determine the direction of induced current in the situations described
by figure.
(a) A wire of irregular shape turning into a circular shape.
(b) A circular loop being deformed into a narrow straight wire.
A. (a) Here, the direction of magnetic field is perpendicularly inwards to the plane of paper. If a
wire of irregular shape turns into a circular shape then its area increases ( The circular loop
has greater area than the loop of irregular shape) so that the magnetic flux linked also
increases. Now, the induced current is produced in a direction such that it decreases the
magnetic field [i.e., the current will flow in such a direction so that the wire forming the loop
is pulled inward in all directions (to decrease the area)], i.e., current is in anticlockwise
direction, i.e., adcba.
(b) When a circular loop deforms into a narrow straight wire, the magnetic flux linked with it
also decreases. The current induced due to change in flux will flow in such a direction that it
will oppose the decrease in magnetic flux so it will flow anticlockwise, i.e., along a 'b'c 'b' a ' ,
due to which the magnetic field produced will be out of the plane of paper.
3. A long solenoid with 15 turns per cm has a small loop of area 2.0 cm2 placed inside the
solenoid normal to its axis. If the current carried by the solenoid changes steadily from
2.0 A to 4.0 A in 0.1 s, what is the induced emf in the loop while the current is changing?
A. Given, number of turns n = 15 per cm = 1500 per meter
Area of small loop A = 2 cm2 = 2 x 10-4 m2
dI 4 − 2 2
Change in current = = = 20 A/s
dt 0.1 0.1
dφ d
e= = (BA) ( φ = BA)
dt dt
dB d
Or e= A = A (µ 0 nI)
dt dt
www.sakshieducation.com
www.sakshieducation.com
dI
Or e = Aµ 0 n
dt
e = 7.5 x 10-6 V
4. A rectangular wire loop of sides 8 cm and 2 cm with a small cut is moving out of a region
of uniform magnetic field of magnitude 0.3 T directed normal to the loop. What is the
emf developed across the cut if the velocity of the loop is 1 cm/s in a direction normal to
the (a) longer side, (b) shorter side of the loop? For how long does the induced voltage
last in each case?
Use the concept of motional emf as wire loop is moving normal to the magnetic field.
A. Given, length of the loop l = 8 cm = 8 x 10-2 m.
Width of the loop b = 2 cm = 2 x 10-2 m
Velocity of the loop = 1 cm/s = 0.01 m/s
Magnitude of magnetic field B = 0.3 T
(l = 8 cm = 8 x 10-2 m)
(l = 2 cm = 2 x 10-2 m)
www.sakshieducation.com
www.sakshieducation.com
e = 0.6 x 10-4 V
t = 8 s.
5. A 1.0 m long metallic rod is rotated with an angular frequency of 400 rad s −1 about an axis
normal to the rod passing through its one end. The other end of the rod is in contact with
a circular metallic ring. A constant and uniform magnetic field of 0.5 T parallel to the
axis exists everywhere. Calculate the emf developed between the centre and the ring?
2 2
6. A circular coil of radius 8.0 cm and 20 turns is rotated about its vertical diameter with an
angular speed of 50 rad/s in a uniform horizontal magnetic field of magnitude 3.0 x 10-2
T. Obtain the maximum and average emf induced in the coil. If the coil forms a closed
loop of resistance 10 Ω , calculate the maximum value of current in the coil. Calculate
the average power loss due to Joule heating. Where does this power come from?
A. Radius of coil = 8 cm = 0.08 m
Number of turns = 20
Resistance of closed loop = 10 Ω
Angular speed = 50 rad/s
Magnitude of magnetic field B = 3 x 10-2 T.
Induced emf produced in the coil E = NBA sin ω t
For maximum emf sin ω t = 1
∴ Maximum emf e0 = NBA ω = 20 × 3 × 10-2 × 3.14 × (0.08)2 × 50
e0 = 0.603 V
e0 0.603
Maximum current in the coil I0 = = = 0.0603 A.
R 10
www.sakshieducation.com
www.sakshieducation.com
1 2π 1 2π
T ∫0 T ∫0
eav = e dt = NBAωsin ωt dt
2π
1 cos ωt
eav = NABω
T ω 0
NBA
= [cos 2π − cos 0o ]
T
NBA
eav = [1 − 1] = 0
T
E 0 I0 0.603 × 0.0603
= = = 0.018 W.
2 2
The source of power dissipated as heat in the coil is the external rotar. The current induced in
the coil causes a torque which opposes the rotation of the coil, so the external agent rotar
counter this torque to keep the coil rotating uniformly.
7. A horizontal straight wire 10 m long extending from east to west is falling with a speed of
5.0m s −1 at right angles to the horizontal component of the Earth’s magnetic field,
0.30 × 10−4 Wb m −2.
(a) What is the instantaneous value of the emf induced in the wire?
(b) According to Fleming’s right hand rule, the direction of emf is from west to east.
www.sakshieducation.com
www.sakshieducation.com
8. Current in a circuit falls from 5.0 A to 0.0A in 0.1 s. If an average emf of 200 V induced,
give an estimate of the self-inductance of the circuit?
dI I −I
As ε = − L = −L 2 1
dt t
0.0 − 5.0
∴ 200 = − L = +50 L
0.1
L = 4 H.
9. A pair of adjacent coils has a mutual inductance of 1.5 H. If the current in one coil
changes from 0 to 20 A in 0.5s, what is the change of flux linkage with the other coil?
A. M = 1.5 H , I1 = 0 A, I 2 = 20 A, t = 0.5s
dφ dI
As ε = − = −L
dt dt
10. A jet plane is travelling towards west at a speed of 1800 km/h. What is the voltage
difference developed between the ends of the wing having a span of 25 m, if the Earth’s
maganetic field at the location has a magnitude of 5 x 10-4 T and the dip angle is 30o?
5
A. Speed of jet plane v = 1800 km/h = 1800 × = 500 m/s
18
www.sakshieducation.com