Alinco DJ-X2000 Wideband Scanner Manual
Alinco DJ-X2000 Wideband Scanner Manual
Alinco DJ-X2000 Wideband Scanner Manual
APPENDIX G:
INSTRUCTION MANUAL
Page 57 of 65
DJ-X2000
Instruction Manual
SP
CLN
RX/S POW ER
F
MO NI SRC H LAM P
DOWN UP VOL SQL
PMS
SET
V FO A B
MR M
SET M O DE
1
STEP
2
ATT
3
HELP
E M NAM
RF C
MIC
4
AUTO
5
MW
KL
6
A-B S
SCN
Thank you for purchasing the ALINCO receiver. The DJ-X2000 instruction manual contains important safety and operating instructions. Read this manual carefully before using the product.
SCRT
7
PRIO
8
S CTCS
9
TF
ENT
SKIP
CLR
REC
0
E F TUN
MIC
NT LLIGE INTEECEIVER R
DJ-X2
Features
The Alinco DJ-X2000 is a professional multifunctional receiver which covers a wide band of radio media from the low-frequency band (LF) to ultrahighfrequency (UHF) band. It has the following features.
The DJ-X2000 covers the wide frequency range from 0.1 to 2149.999950 MHz. The DJ-X2000 has three basic modes: Dual VFO, Memory (MR), and Scan Programming (PMS). The modes can be switched by one-touch operation. Memory function allows you to program the frequencies up to 2000 channels. (40 ch 50 banks) Various kinds of scan are available: Program scan (PMS), Memory scan, Mode-select scan, VFO scan, VFO-linked scan, and Priority scan. The PMS mode has a total of 20 programmable bands. The search function checks frequencies in the set frequency steps and displays signals within a 40channel or 7-channel range at once. The battery-save function automatically saves on battery power whenever keys are not used or a signal is not picked up for a certain amount of time. You can copy the settings stored in memory from one DJ-X2000 to another. Moreover, you can connect the DJ-X2000 with a personal computer to copy the settings. You can select a signal mode from AM, NFM, WFM, LSB, USB, CW, and AUTO. When AUTO is selected, the DJ-X2000 automatically determines the most suitable signal mode for currently receiving frequency. Channel step is selectable from 23 fixed steps, or you can set any step between 50 Hz - 500 kHz. In addition, the DJ-X2000 determines the most suitable channel step for currently receiving frequency when AUTO is selected.
3. Memory capacity
4. Scanning
7. Battery-save function
8. Cloning
You can copy the content of one memory channel to another, or rename memory channels. The DJ-X2000 detects the listening microphone which transmits a radio wave. If a listening microphone is found, the DJ-X2000 will alert you with a display and warning sound. The DJ-X2000 records the sound of currently receiving signal or from the microphone, and replays it. The maximum recording time is 160 minutes. The DJ-X2000 can return scrambled voice transmission to a normal voice reception. If there are signals around the DJ-X2000, it tunes in the strongest frequency in a flash. This function allows you to use the DJ-X2000 as a radio frequency checker. The DJ-X2000 can measure the electric field strength and indicate it on the display. The built-in microphone picks up the sound and amplifies it. The DJ-X2000 can be used as a transceiver or transmitter using 250 MHz band. The DJ-X2000 receives FM radio in stereo. The DJ-X2000 decodes the CTCSS signal. Using this function, the squelch unmutes only when the DJ-X2000 fails to receive a modulation signal of 2300 Hz. The Help-navigator shows how to use each function of the DJ-X2000 on the display. Moreover, you can jump to the setting display of currently displayed function from the help menu, and execute the function.
12. Transweeper
14. Descrambler
16. RF checker
20. Receiving FM radio in stereo 21. CTCSS decoder 22. A/B squelch
23. Help-navigator
24. Exceedingly sensitive antenna for HF and MF Newly developed antenna is attached. 25. DC switching power supply DC switching power supply saves on the battery power. High (20 dB) and Low (10 dB) attenuators are available.
Contens
1. Before use 00
1.1 Unpacking the receiver 00 1.2 Precautions in use 00 1.3 Names of parts and their funciotns 00
1.3.1 Top, front and left side panels 00 1.3.2 Rear and right panels 00 1.3.3 Display 00 1.3.4 Key pad 00
2. Basic operations 00
2.1 POWER switch 00 2.2 Volume control 00 2.3 Squelch control 00 2.4 Setting frequency 00 2.5 Switching frequency band 00 2.6 Copying frequencies from one band to the other 00 2.7 Scanning 00 2.8 Sarching(Channel Scope) 00 2.9 Monitoring(Squelch OFF) 00 2.10 Turning backlight ON/OFF 00
2.10.1 Turning backlight ON/OFF manually 00 2.10.2 Turning backlight ON/OFF based on the setting 00
2.11 Turning beep ON/OFF 00 2.12 Locking/Unlocking 00 2.13 Setting the clock 00
2.13.1 Setting the OFF timer 00
2.13.2
3.2
3.2.1 VFO link function 00 3.2.2 Scanning between VFO's A and B(AB SCAN) 00 3.2.3 Copying frequencies from memories to the VFO 00 3.2.4 Copying frequencies from the PMS mode to the VFO 00
4.Appendix00
4.1 Specifications 00 4.2 Troubleshooting 00 4.3 Otpitional items 00 4.4 List of Help menu items 00
Note:
The note icon contains additional information pertinent to product use, which is helpful but not necessarily known.
NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.
6a
1. Before use
1.1 Unpacking the receiver
The DJ-X2000 should come with the following accessories. Check that nothing is missing when you first open the package. Antenna 1 Charger 1 EBP-37N (Ni-Cd battery pack ) 1 Belt clip 1 Belt clip screws 2 Wrist strap 1 DJ-X2000 Instruction Manual (This manual) 1 Standard accessories may differ depending on the version.
CLN
T RX/S ER POW
5. 6. 7. 8. 9.
F
MO NI SRC H LAM P
DOWN UP VOL SQL
PMS
SET
VFO A B
W MR M
SET
10.
M OD E
1
STEP
2
ATT
3
HELP
E M NAM
RF C
MIC
4
MW AUTO
5
KL
6
A-B S
SCN
19.
SCRT
7
PRIO
8
S CTCS
9
TF
ENT
SKIP
CLR
REC
0
E F TUN
MIC
20.
NT LLIGE INTEECEIVER R
DJ-X2
1. Dial
Use to switch frequency and memory channel, to adjust the audio volume and squelch level, and to make other settings. Use to clone settings between two DJ-X2000s, and to connect with the PC editor. Connect an external speaker with amplifier or earphone here. FM radio can be received in stereo when stereo speakers or stereo earphones are connected. BNC connector. Attach the included antenna here.
4. Antenna connector
5. 6. 7.
Use this key in combination with other keys to call up specific functions. Temporarily cancels the squelch for the duration it is held down. Used independent of squelch level. Press to start scanning with in a 40-channel range. Use in combination with F key to start scanning in a 7-channel range. In transceiver mode, this key is used as a PTT key. (See "Note" below.) Turns the key backlight ON/OFF. Use to adjust the audio volume and squelch level. Use to set frequency, to adjust the audio volume and squelch level, to set various settings, and to select an item in menu display. Turns power ON/OFF.
MONI
SRCH
LAMP
8.
key
12. Hardware reset key Press to reset all functions to their factory-settings. However, data stored in memory is not deleted. Settings might return to the settings when power was turned ON the last time. 13. Busy lamp Lights green when a signal is picked up and stays lit while the signal is alive. Lights orange when receiving FM radio in stereo (using stereo earphones). In Transceiver mode, lights red while transmitting. Sound is produced from here. Shifts to the scan programming mode. If pressed in combination with the F key, the scan program can be saved in memory. Engages the dual VFO mode. If pressed in combination with the F key, the frequency displayed in the top band is copied in the bottom band. Use to access the memory. If pressed in combination with the F key, frequencies and other data can be saved in memory. Displays frequency, operating status and other information pertinent to use. In the VFO mode, use these keys to directly input the frequency you want. Press in combination with the F key to access other functions.
key
16.
VFO A=B
key
MRMW
17.
key
20. Built-in microphone Use to pick up the sound and record it, or use in transceiver mode.
Note: PTT (Press to talk) key is usually attached to a transceiver. In the DJ-X2000, SRCH the key is used as a PTT key in transceiver mode. You can transmit a signal while PTT key is held down, or every press of PTT key switches between transmission and reception.
2.
1. 3.
4.
1. DC-IN
2. Holes for attaching belt clip Screw the included belt clip to the DJ-X2000 here. 3. Battery case lock Slide to the right to detach the battery case.
4. EBP-37N battery pack or dry cell case The dry cell case can hold four AA batteries.
10
1.3.3 Display
1. 2.3.4. 5. 6. 7. 8. 10. 12. 14. 9. 11. 13. 15. 16. 17.
AM
18.
1. 2.
Meter for displaying sound level. Displayed when the F key has been pressed to indicate that you can access the subfunctions of the keys. Displayed while the priority function is ON. Displayed in the MR mode. Displayed in the PMS mode. Displayed for memoroy channels which are skipped in memory scans. Skip is user-set. Displayed in the VFO mode. Displayed when the attenuator is ON. Displayed when a frequency indivisible by the set frequency step is entered. Displayed when the bell function is ON. Displayed when the CTCSS decoder is ON. Displayed when On-timer or Off-timer is ON. Displayed while keys are locked. Displayed when the battery-save function is ON. Displayed when battery power is low. Promptly replace the batteries if this icon is displayed. Signal mode is displayed. When the audio volume or squelch level is being adjusted, either of them is displayed. S-meter. Depending on settings, the time or the channel scope setting is also displayed here. This is where band, channel name and frequency are displayed in the various modes.
3. PRIO 4. M 5. PMS 6. SKIP 7. VFO 8. ATT 9. S 10. 11. T 12. 13. 14. BS 15. 16. AM
11
Inputs 1. Press in combination with the switch the radio band. Inputs 2. Press in combination with the frequency step. Inputs 3. Press in combination with the the attenuator ON/OFF.
key to
2.
STEP 2
key to set
3.
ATT 3
key to turn
4.
MIC 4
Inputs 4. Press in combination with the key to turn the Directional microphone function ON. Inputs 5. Press in combination with the the auto memory write function ON/OFF. Inputs 6. Press in combination with the lock/unlock keys. Inputs 7. Press in combination with the the Descrambler. Inputs 8. Press in combination with the the priority function ON/OFF. Inputs 9. Press in combination with the the CTCSS decoder. key to turn
5.
AUTO MW 5
6.
KL 6
key to
7.
SCRT 7
key to set
8.
PRIO 8
key to turn
9.
CTCSS 9
key to set
10.
SKIP CLR
Clears settings. In VFO mode, press in combination with the F key to set VFO-link. In PMS and MR modes, press in combination with the F key to set the scan pass frequency and skip channel. Inputs 0. Press in combination with the turn the recording function ON. key to
11.
REC 0
F TUNE
12.
SET HELP
Inputs (decimal point). Press in combination with the key to set the Flash tune function. Press to call up the Help-navigator. Press in combination with the key to call up menus. Press to turn the RF checker ON. Press in combination with the key to turn the Memory search function ON. Starts scanning. Press in combination with the key to scan between band A and band B. Enters input values. Press in combination with the key to turn the Transweeper ON.
13.
14.
M NAME RFC
15.
A~B S SCN
16.
TF ENT
12
SP
CLN
RX/ST POWE R
F
MO NI SRC H
P VOL SQL
PMS
SET
VFO A B
MR MW
13
To attach the battery pack Fit the battery pack into the holes on the DJ-X2000 and push in the direction of the arrow until the case snaps into the place.
14
15
Illuminated in green Supplemental recharge is in progress. Blinking in green Blinking in red Blinking alternately in red and green Supplemental recharge is completed. Supplemental recharge is in progress for the completely discharged battery pack. An irregular battery pack is in place.
Recharging terminals
Used for recharging the battery pack.
AC power socket
Used to plug the AC power cord.
AC power cord
Used to supply AC power.
16
Recharging procedure
LAMP
DOWN
1
SET ATT MODE
1
HELP
Plug the AC power cord into the AC power socket on the battery charger. Insert the battery pack being recharged, along the guides provided on both sides of the battery charger. The lamp will be illuminated in red, and quick recharge will be started. When the quick recharge is completed, the lamp changes its color to green, indicating that supplemental recharge (*) has started. About four hours after the quick recharge has started, the lamp starts blinking in green, indicating that the supplemental recharge has been completed.
STEP
2
M NAM
RF C
MIC
4
AUTO
5
MW
KL
6
A-B S S E
SCN
SCRT
7
PRIO
8
CTCS
9
TF
ENT
SKIP
CLR
REC
0
F TUN
MIC
DJ-X2
2 3 4
Note:
The supplemental recharge means recharging the battery pack with small electric current to prevent its capacity from decreasing due to the selfdischarge. This does not overload the battery pack.
Battery pack vs. recharging time The battery packs applicable to each battery charger model and their recharging time are shown below:
Battery pack EBP-33N EBP-34N EBP-35N EBP-37N EBP-47N Battery capacity 4.8V 650mAh 4.8V 1200mAh 7.2V 900mAh 4.8V 700mAh 7.2V 700mAh Recharging time Approx. 1 hour Approx. 1.5 hours Approx. 1.2 hours Approx. 1 hour Approx. 1 hour
17
Precautions in recharging 1. Ensure that the transceiver is OFF when recharging the battery pack. The use of the transceiver during the recharging can cause the transceiver to malfunction. 2. The battery charger is designed to be used at an ambient temperature between 10C and 40C. Avoid recharging the battery pack at any temperature outside this range. 3. Do not repeatedly recharge the fully recharged battery pack. This can cause the performance of the battery pack to deteriorate. The battery pack can be recharged 500 times when it is used normally. If the life of the completely recharged battery pack becomes markedly shorter, the battery pack is considered to have been exhausted. Please purchase a new battery pack. 4. Do not insert the battery pack in a reverse direction. 5. When the battery pack has been recharged completely with the lamp blinking in green, remove the battery pack from the battery charger. 6. If the battery charger is not used for a long period of time, disconnect the AC power cord from the wall socket, and remove the battery pack from the battery charger. 7. If you recharge the battery pack of which voltage has abnormally dropped due to discharge, the lamp starts blinking in red and the preliminary recharge initiates immediately after you have started recharging the battery pack. Subsequently, the lamp will be illuminated in red, indicating that the quick recharge has started. 8. If any irregular battery pack is set in place, the lamp will blink alternately in red and green.
18
2. Basic operations
This chapter describes the basic operations for the DJ-X2000.
F
MO NI SRC H
P VOL
PMS
SET
Hold down the POWER switch for approx. 1 second until the message ALINCO INTELLIGENT RECEIVER appears on the display.
SQL
VFO A B
MR MW
Turning OFF Hold down the POWER switch until the display goes out.
Note: The message that appears on the display may be changed (see 3.1.12 Changing the initial message on page 41).
F
MO NI SRC H LAM P
DOWN UP VOL
PMS
SET
VFO A B
MR MW
To turn up the volume, press the VOL key located on the left side of V1 6 the body, and then press the UP A 145 . 34 key or turn the dial clockwise. To b 8 . turn down the volume, press the VOL key, and then press the DOWN key or turn the dial counterclockwise. The bars on the display will increase/decrease with
SQL
the adjacent number changed between V00 and V32 as you control the volume.
Note:
To disengage the squelch (the mute function) temporarily, press and hold the
MONI
key on the left panel. This will enable you to set the volume setting
without changing the squelch setting (see 2.3 Squelch control page 21).
19
VFO A B
MR MW
To select a squelch level, press the SQL key located on the left side of the body, and then press the UP/DOWN key or turn the dial. The squelch level will be shown on the display in accordance with the setting.
S 5 A 145 . 34 b 8 .
SQL
Note:
Higher squelch levels require higher signal levels to release the muting. Set the squelch to a level at which the noise just disappears. The level at which to release the muting varies depending on the received frequency even if the electric field strength remains the same. Adjust the squelch at the most suitable level for the frequency to be received. If the squelch level is too high, weak incoming signals may not be heard from the speaker.
STEP
2
ATT
3
HELP RF C
M NAME A-B S
SCN
MIC
4
AUTO
5
MW
KL
6
SCRT
7
PRIO
8
CTCSS
9
NFM A 145 . 34 b 8 .
TF
ENT
SKIP
CLR
REC
0
F TUNE
MIC
DJ-X2
MODE 1 MIC 4 AUTO MW 5 F TUNE
Example 1
MIC 4
, and
TF ENT
The 00 on the end can be omitted. Example 2 To set 0.5580 MHz (that is, 558 kHz), press the , , , The 0 on the end can be omitted.
AUTO MW 5 AUTO MW 5 PRIO 8
and
TF ENT
20
Note:
If you enter any frequency that cannot be divided by the set frequency step, S appears on the display.
Setting with the UP/DOWN key F For higher frequencies, press the UP key. For lower MO NI frequencies, press the DOWN key. The frequency will SRC H increase/decrease in the set frequency steps.
VOL
PMS
SET
SQL
LAM P
DOWN
UP
VFO A B
MR MW
Note:
For changing the frequency steps, see 3.1.2 Setting the frequency steps (page 33).
Setting from the dial For higher frequencies, turn the dial clockwise. For lower frequencies, turn it counterclockwise. The frequency will CLN SP increase/decrease in the set frequency steps.
T RX/S ER POW
F
S
Note:
For changing the frequency steps, see 3.1.2 Setting the frequency steps (page 33).
SQL
Setting with the combination of the F key and the dial Press the F key, and then press the UP/DOWN key with shown on the display. An under-bar will appear at CLN SP the digit of 100, 10, or 1 MHz. Now turning the dial allows you to change the number at that digit. Pressing the F UP/DOWN key shifts the digit at which the number can be MO NI changed.
T RX/S ER POW
VOL
PMS
SET
SRC H LAM P
DOWN UP
VFO A B
MR MW
M NAME
21
VFO A B
MR MW
Press the key. The frequencies on the top and bottom lines will switch places, with the letters changing between capital and lower case.
VFO A=B
NFM B 8 . a 145 . 34
SQL
F
MO NI SRC H LAM P
WN UP VOL
PMS
SET
SQL
VFO A B
This will copy the frequency on the currently used band (displayed on top line next to capital letter) into the other band (displayed on bottom line next to small case letter).
2.7 Scanning
Scanning is used to locate frequencies with signals present. Basic scanning operations are as follows. To scan P
DOWN
SET MODE
1
STEP
2
ATT
3
HELP
M NAME
RF C
MIC
4
MW AUTO
5
KL
6
A-B S
SCN
SCRT
7
PRIO
8
CTCSS
9
TF
ENT
SKIP
CLR
REC
0
F TUNE
MIC
DJ-X2
Press the SCN key. Scanning will NFM start and will proceed in the set A 145 . 34 frequency steps. b 145 . 34 While scanning, an arrow icon is displayed next to the frequency on currently used band (displayed on top line next to capital letter). The arrow points to the left while scanning towards the higher frequencies.
A~B S
Note:
If CTCSS or A/B Squelch is selected, the scan may be delayed since it takes some time for judgment.
22
If live frequencies are received, scanning is temporarily stopped. To resume scanning, turn the dial or press the UP/DOWN key. Scanning can be automatically resumed by specifying scan resuming conditions. For further details, see 3.1.15 Specifying scan resuming conditions (page 43). To switch scanning direction While scanning, press the DOWN key. The arrow icon will face right and scanning will proceed toward the lower frequencies. To scan toward the higher frequencies, press the UP key. The scanning direction can also be changed by turning the dial. To cancel scanning Press the
A~B S SCN
key again.
VFO A B
MR MW
Press the key on the left side WFM panel. The DJ-X2000 will start A 81 . 5 searching for signals within a 40b 145 . 34 channel range of the currently received frequency. The search proceeds in the set frequency steps with the displayed frequency in the center under M mark. The higher channel spectra are displayed towards the right, and the lower to the left. Vertical length of each spectrum indicates strength of the signals.
SRCH
7-channel search
T RX/S ER POW
SQL
F
MO NI SRC H LAM P
UP VOL
PMS
SET
VFO A B
MR MW
Press the F key to display WFM Then, press the SRCH key on the left A 81 . 5 side panel. The DJ-X2000 will start b 145 . 34 searching for signals within a 7channel range of the currently received frequency. The search proceeds in the set frequency steps with the displayed frequency in the center under M mark. The higher channel spectra are displayed towards the right, and the lower to the left. Vertical length of each spectrum indicates strength of the signals.
SQL
23
To tune in live frequencies To move live frequencies to the left, turn the dial clockwise or press the UP key. To move them to the right, turn the dial counterclockwise or press the DOWN key.
SP
CLN
RX/ST
POWE
MO NI
VOL
PMS
SET
WFM A 81 . 5 b 145 . 34
SQL
SRC H
MR MW
LAM P
DOWN
UP
VFO A B
SET
Note:
For specifying search steps and search resuming conditions, see 3.1.22 Specifying search resuming conditions (page 49). The search resume condition factory-setting is INTERVAL. Sound is muted during the search. The search operation is performed every 10 seconds. It may be difficult to read a value from the S meter during scanning in the Channel Scope mode, because the speed is fast. The graph displayed in the Channel Scope mode is only in the range of the currently received radio type. For example, if search is performed around 76.5 MHz of WFM, no channel for less than 76.0 MHz, which is of NFM, is not displayed. If the Channel Scope mode is selected, the battery saving function is disabled. If the search function is turned ON in the MR mode, it may take some time for the full display of search. If scanning is started with the search function turned ON, it may take some time to start scanning.
VOL
PMS
SET
SQL
UP
VFO A B
MR MW
MONI
F
MO NI SRC H LAM P
N UP VOL
PMS
SET
VFO A B
MR MW
Press the F key to display , followed by the key. MONI The squelch will remain OFF even after the key has MONI been released. Pressing the key a second time will reactivate the squelch.
24
SQL
SET
ATT
HELP
To leave the backlight ON at all times Press the F key to display , followed by the F The backlight will remain ON until you press the MO NI
ER POW
LAMP
key.
VOL
PMS
SET
SQL
LAMP
SRC H LAM P
DOWN UP
VFO A B
MR MW
key again.
1
F
MO NI SRC H LAM P
Display the LAMP screen. Press the F key, and then press SET LAMP the HELP key with displayed. MOME N T A R Y The menu will appear. Using the ALTERNATE dial or the UP/DOWN key, point TF the arrow at +CONFIG, and then press the ENT key. The CONFIG menu will appear. Point the arrow at TF +LAMP, and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
SCN
MIC
4
MW AUTO
5
KL
6
SCRT
PRIO
CTCSS
9
TF
25
Select a backlight mode as follows: Using the dial or UP/DOWN key, point the arrow at a desired mode, and then TF press the ENT key (the initial setting is the MOMENTARY mode). AUTO: The backlight is lit for 5 seconds after the dial or key is used. LAMP MOMENTARY: The backlight remains lit only while the key is being held down. ALTERNATE: The backlight is turned alternately ON and OFF every time LAMP the key is pressed. The display will go back to the CONFIG menu. Point the arrow at END, and then TF TF press the ENT key (or alternatively, press the F key, and then press the ENT key with
Note:
1
F
MO NI SRC H LAM P
VOL
PMS
SET
DOWN
UP
VFO A B
MR MW
SET MODE
1
STEP
2
ATT
3
HELP
Press the F key, and then press SET BEEP the HELP key with shown on H i gh the display. The menu will L OW appear. Using the dial or the UP/DOWN key, point the arrow at +CONFIG, and then TF press the ENT key. The CONFIG menu will appear. Point the arrow at +BEEP, and then press the TF key.
ENT
SQL
M NAME
RF C
MIC
4
MW AUTO
5
KL
6
A-B S
SCN
SCRT
PRIO
CTCSS
9
TF
Select a beep sound mode. Using the dial or the UP/DOWN key, point the arrow at a desired mode, and then TF press the ENT key (the initial setting is the HIGH mode). OFF: The beep sound is turned OFF. HIGH: The beep sound is emitted at a high level. LOW: The beep sound is emitted at a low level. The display will go back to the CONFIG menu. Point the arrow at END, and then TF TF press the ENT key (or alternatively, press the F key, and then press the ENT key with
Note:
26
If you exit the CONFIG menu by pressing the CLR key, the changed setting is canceled. If stereo earphones are used, the beep sound can be heard from the left earphone only.
2.12 Locking/Unlocking
This feature locks all but certain keys, preventing accidental operation of the keys. Keys can be locked/unlocked as follows. To lock keys
ER POW
Press the
KL 6
F
MO NI SRC H LAM P
DOWN UP VOL
PMS
SET
VFO A B
MR MW
SET MODE
1
STEP
2
ATT
3
HELP
M NAME
RF C
NFM the key with F { } A 81 . 5 appearing on the display. b 145 . 34 will appear on the display and the keys will be locked except for the POWER MONI switch, dial, and , VOL/SQL, UP/DOWN, F , and LAMP keys.
SQL
MIC
4
MW AUTO
5
KL
6
A-B S
SCN
SCRT
PRIO
CTCSS
9
TF
key to display
, followed by the
KL 6
1
F
MO NI SRC H LAM P
Call up the TIMER menu. Press the F key, and then press
R POWE
VOL
PMS
SET
DOWN
UP
VFO A B
MR MW
SET MODE
1
STEP
2
ATT
3
HELP
M NAME
RF C
MIC
4
MW AUTO
5
KL
6
A-B S S
SCN
SCRT
7
PRIO
8
CTCS
9
TF
ENT
SKIP
CLR
REC
0
F TUNE
T I MER SET the HELP key with appearing ON T i me r O F F T i me r on the display. The TIMER menu will appear. Point the arrow at +CONFIG using the dial or UP/DOWN key, and then press TF the ENT key. The CONFIG menu will appear. Point the arrow at +TIMER and then press the TF key.
ENT
SQL
27
2 3
Call up the OFF timer screen. Point the arrow at +OFF Timer using the dial or UP/DOWN TF key, and then press the ENT key.
Set the OFF timer. Point the arrow at ON using the UP/DOWN key, and then set the time that will be taken until the power is automatically turned OFF (the initial setting is OFF). The time can be set up to 24 hours in 30-minute steps. If OFF is selected, the OFF timer is disabled.
TF
O F F T i me r OFF :3 ON
After finishing the setting, press the ENT key. The display will return to the TIMER menu. Point the arrow at END and then press the TF key. ENT (Alternatively, you may press the F key, TF and then press the key with appearing on the display.)
ENT SKIP
Note:
If you exit the TIMER menu by pressing the CLR key, the setting is canceled. If you set the OFF timer again, the power is turned OFF after the set time TF has elapsed from the time when the ENT key is pressed. If the battery is removed or if the hardware reset key is pressed, the setting is canceled.
1
F
MO NI SRC H LAM P
Call up the TIMER menu. Press the F key, and then press SET T I MER the HELP key with appearing on ON T i me r the display. The TIMER menu will O F F T i me r appear. Point the arrow at +CONFIG using the dial or UP/DOWN key, and then press TF the ENT key. The CONFIG menu will appear. Point the arrow at +TIMER, and then press the TF key.
R POWE
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
SCN
MIC
4
MW AUTO
5
KL
6 9
SCRT
7
PRIO
8
CTCS
TF
SKIP
CLR
REC
0
F TUNE
ENT
ENT
2 3
Call up the ON Timer screen. Point the arrow at +ON Timer using the dial or UP/DOWN TF key, and then press the ENT key.
ON T i me r OFF :3 ON
Set the ON timer. Point the arrow at ON using the UP/DOWN key, and then use the dial to set the time that will be taken until the power is automatically turned ON (the initial setting is OFF). The time may be set up to 24 hours in 30-minute steps. If OFF is selected, the ON timer is disabled.
28
SET HELP
TIMER menu. Point the arrow at END and then press the HELP key. (Alternatively, you may press the F key, and then press the SET key with HELP appearing on the display.)
Note:
SKIP If you exit the TIMER menu by pressing the CLR key, the setting is canceled. If you set the ON timer again, the power is turned ON after the set time has SET elapsed from the time when the HELP key is pressed. If the battery is removed or if the hardware reset key is pressed, the setting is canceled.
Press the
MR MW
VFO A=B
the VFO mode. (If the VFO mode is already engaged, pressing the key will switch between bands A and B.)
VFO A B
NFM A 145 . 34 b 8 .
SQL
M NAME
To tune in frequencies or switch bands, see "2.4 Setting frequency" on page 21 and "2.5 Switching frequency band" on page 23.
29
1
F
MO NI SRC H LAM P
Enter the PMS mode. PMS SET Press the key. This will engage WFM the PMS mode. Then, select a P5 1 4 . 75 registered band and start scanning. TV 1 - 3 c h Bands are preregistered before the DJ-X2000 is shipped from the factory, but they can be changed in the expert's mode. (See "3.3.1 Programmed scan operations" on page 67.)
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
STEP
ATT
HELP
ME
Select between P and p. F TUNE Press the key to switch back and forth between the capital P and the lower case p. Select a memory bank group. Press the numeric key for the bank you want. The corresponding programmed scanning will start. The scanning direction can be changed using the dial or UP/DOWN key. If you press another numeric key, the corresponding programmed scanning will start.
2 3
2.14.3 MR mode
The memory mode provides five bank groups from A through E. Each bank group has 10 banks (0-9), each of which allows you to assign a maximum of 40 channels of frequencies (00-39).
1
F
MO NI SRC H LAM P
DOWN UP VOL SQL
VFO A B
Enter the MR mode. MRMW Press the key. This will AM engage the MR mode and will A3 1 . 278 display registered frequencies and RK B names. Frequencies are preregistered before the DJ-X10 is shipped from the factory, but they can be changed in the expert's mode. (See "3.5.1 Memorizing frequencies" on page 46.)
ER POW
PMS
SET
MR MW
2 3
30
Select the memory bank group. F TUNE Press the key to switch between memory bank groups A, B and C. Select a bank. Press the numeric keys for the bank No. you want in the selected group.
Select a channel. Using the dial or UP/DOWN key, select a channel between 00 and 39. The assigned frequency will appear on the upper line of the display and its name on the lower line.
1
SRC H
UP
LAM P
DOWN
Display the HELP menu. SET Press the HELP key. The HELP menu will appear.
VFO A B MR MW
HELP HE L P KEY
SET MODE
1
STEP
2
ATT
3
HELP
M NAME
RF C
MIC
4
AUTO
5
MW
KL
6
A-B S
SCN
SCRT
PRIO
CTCSS
9
TF
T
NE
Select the function on which you want to view an explanation. Point the arrow at the desired item using the dial or TF UP/DOWN key, and then press the ENT key. The KEY submenu for that item will appear. SET P OWER Some items have a submenu below them. Similarly point the arrow at the desired item, and then press the ENT SKIP key. Pressing the CLR key puts you back to the upper layer.
TF
Select a HELP item. TF Point the arrow at Inst. and then press the ENT key. The TONE selected function will be explained. TF Point the arrow at Set! and then press the ENT key. You will go to the setup screen for that function. TF If you point the arrow at any item followed by ! and then press the ENT key, the selected function will be executed. Exit the HELP mode. SKIP Hold down the CLR key until you go back to the previous screen.
Note: The HELP information can be displayed in English. For further details, see 3.1.7 Selecting displayed language (page 38). Selecting the Set! item exits the HELP mode. To view the HELP information TF again, press the ENT key after establishing Set! or canceling it by pressing the
SKIP CLR
key.
31
F
MO NI SRC H LAM P
DOWN UP VOL
PMS
SET
VFO A B
MR MW
Press the F key, and then press MODE the 1 key with appearing on MODE WFM AU T O the display. The MODE screen will AM appear. Point the arrow at the desired signal mode using the dial or UP/DOWN key, and TF then press the ENT key. A signal mode can be selected from AM, NFM, WFM, USB, LSB, CW, and AUTO. If AUTO is selected, the most suitable signal mode will be automatically selected in accordance with the received frequency (the initial mode is AUTO).
SQL
SET MODE
1
STEP
2
ATT
3
HELP
M NAME
RF C
MIC
4
AUTO
5
MW
KL
6
A-B S
SCN
SCRT
7
PRIO
8
CTCSS
9
TF
ENT
SKIP
R
REC
0
F TUNE
Note:
In the PMS or MR mode, when DIRECT WR is turned ON (the initial setting is OFF), a signal mode can be selected. For further details, see 3.3.31 Directly changing the setting (page 63).
STEP 1 KHz AU T O S T E P 5 Hz
F
MO NI SRC H LAM P
DOWN UP VOL
PMS
SET
VFO A B
MR MW
Press the F key to display , followed by the STEP key. 2 This will display the MODE menu. Then, move the arrow to the signal mode you want, using the dial or TF the UP/DOWN key, and press the ENT key. A frequency step can be selected from AUTO STEP, 50 Hz, 100 Hz, 200 Hz, 500 Hz, 1 kHz, 2 kHz, 5 kHz, 6.25 kHz, 8.33 kHz, 9 kHz, 10 kHz, 12.5 kHz, 15 kHz, 20 kHz, 25 kHz, 30 kHz, 50 kHz, 100 kHz, 125 kHz, 150 kHz, 200 kHz, 250 kHz, 500 kHz, and USER STEP.
SQL
SET MODE
1
STEP
2
ATT
3
HELP
M NAME
RF C
MIC
4
AUTO
5
MW
KL
6
A-B S
SCN
SCRT
7
PRIO
8
CTCSS
9
TF
ENT
SKIP
R
REC
0
F TUNE
32
Note:
In the PMS or MR mode, setting DIRECT WR to ON enables selection of a frequency step and radio type and adjustment of the attenuator and CTCSS decoders. For further details, see 3.3.31 Directly changing the setting (page 63).
If AUTO STEP is selected, the most suitable frequency step for the received frequency band will be automatically selected. If USER STEP (optional) is selected, a frequency step can be selected freely in a range between 50 Hz and 499.95 kHz. REC F TUNE MODE AUTO MW TF 5 Example: To enter 150 kHz, press: 0 , , 1 , , ENT TF To enter 450 kHz, press: REC , F TUNE , MIC , AUTO MW , ENT 0 4 5 Even if a frequency that cannot be divided by the selected step is entered, it is accepted. In this case, however, the beep sound is emitted and S appears on the display showing that the DJ-X2000 is operating in non-standard steps.
Note:
NFM A 81 . b 145 . 34
The frequency step in the AM mode is fixed to 10 kHz for the North American version and 9 kHz for the European version.
1
F
MO NI SRC H LAM P
DOWN
UP
Call up the ATT screen. Press the F key, and then press ATT the 3 key with appearing on the display. The ATT screen will appear.
ER POW
VOL
PMS
SET
VFO A B
MR MW
ATT OFF L OW
SQL
SET MODE
1
STEP
2
ATT
3
HELP
M NAME
RF C
MIC
MW AUTO
KL
6
A-B S
Selecting an attenuation level Point the arrow at the desired attenuation level using the dial or UP/DOWN key (the initial setting is OFF). OFF Turns the attenuator OFF. LOW Attenuates the affected signals by approx. 10 dB. HIGH Attenuates the affected signals by approx. 20 dB. ATT will appear on the display showing that the attenuation function is turned ON.
33
Note:
The attenuation level slightly varies depending on the frequency. In the PMS or MR mode, setting DIRECT WR to ON enables selection of a frequency step and radio type and adjustment of the attenuator and CTCSS decoders. For further details, see 3.3.31 Directly changing the setting (page 63).
1
F
MO NI SRC H P LAM
Call up the BATT SAVE screen. Press the F key, and then press SET BATT SAVE the HELP key with appearing on OFF the display. SHOR T The menu will appear. Point the arrow at +CONFIG using the dial or UP/DOWN key, and TF then press the ENT key. The CONFIG menu will appear. Point the arrow at +BATT TF SAVE and then press the ENT key.
R POWE
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
SCN
MIC
4
AUTO
MW
KL
6 9
SCRT
7
PRIO
8
CTCSS
TF
SKIP
CLR
REC
0
F TUNE
ENT
Select an ON/OFF ratio for the battery saving feature. Point the arrow at the desired ON/OFF ratio using the dial or UP/DOWN key, and TF then press the ENT key (the initial setting is NORMAL). The display will return to the CONFIG menu. Point the arrow at END and then TF press the ENT key (Alternatively, you may press the F key, and then press TF the ENT key with appearing on the display).
SKIP
Note:
If you exit the CONFIG menu by pressing the CLR key, the changed setting will be canceled. If LONG is selected, the time to keep the internal power source OFF becomes longer. This extends the battery life, but delays the receiving reaction.
34
Turn ON two DJ-X2000 units and interconnect them. Detach the cap from the top of each unit. As illustrated below, connect the cable between the CLN terminals.
2
F
MO NI SRC H P LAM
Execute a cloning command. Press the F key, and then press the SET appearing on the CLONE HELP key with WR I T E display. The CLONE menu will RE AD appear. Point the arrow at +CONFIG using the dial or UP/DOWN key, and then press the TF ENT key. The CONFIG menu will appear. Point the arrow TF at +CLONE, and then press the ENT key. Point the arrow at the desired cloning command using the TF dial or UP/DOWN key, and then press the ENT key. This operation is not required for the slave unit.
R POWE
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
SCN
MIC
4
AUTO
MW
KL
6 9
SCRT
7
PRIO
8
CTCSS
TF
SKIP
REC
0
F TUNE
ENT
CLR
Copies the data stored in the memory from the other DJ-X2000 unit. Copies the data stored in the memory to the other DJ-X2000 unit. Cancels the cloning command without copying any data.
When READ is selected: Displayed on the master unit CLONE DATA R ECE I V I NG When WRITE is selected: Displayed on the master unit CLONE DATA S END I NG
35
When the cloning procedure is finished, the slave unit returns to the normal screen and the master unit to the CLONE menu.
Finish the cloning procedure. Once the cloning procedure is finished, disconnect the cable from both DJSKIP X2000 units. Press the CLR key on the master unit to exit the CLONE menu. The slave unit can be used without this operation.
CAUTION: Do not disconnect the cable, nor turn the power OFF during the cloning procedure. If a cloning error occurs, press the hardware reset key or remove the battery.
ATT 3
key.
MO
VOL SQL
PMS
SET
NI
SRC
H P
DOWN UP
VFO A B
MR MW
LAM
SET MODE
1
STEP
2
ATT
3
HELP
M NAME
RF C
MIC
MW AUTO
KL
6
A-B S
To select 19200 bps: Turn the power ON while holding down the
R POWE
STEP 2
key.
F
MO
VOL SQL
PMS
SET
NI
SRC
H P
DOWN UP
VFO A B
MR MW
LAM
SET MODE
1
STEP
2
ATT
3
HELP
M NAME
RF C
MIC
MW AUTO
KL
6
A-B S
36
Note:
The cloning procedure or communication with a personal computer is not possible between DJ-X2000 units with different communication speeds. The initial value is a high speed of 38400 bps. If there are too many communication errors at this speed, retry the communication at a lower speed, e.g., 9600 bps.
1
F
MO NI SRC H P LAM
Call up the LANGUAGE screen. SET Press the F key, and then HELP LANGUAGE key with shown on the display. Japanese The LANGUAGE screen will Eng l i s h appear. Point the arrow at +CONFIG using the dial or TF UP/DOWN key, and then press the ENT key. The CONFIG menu will appear. Point the arrow at TF +LANGUAGE and then press the ENT key.
R POWE
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
MIC
MW AUTO
KL
6
Select a language mode. Point the arrow at English or Japanese using the dial or UP/DOWN key, and TF then press the ENT key (the initial setting is English). The display will return to the CONFIG menu. Point the arrow at END and then TF press the ENT key (Alternatively, you may press the F key, and then press TF the ENT key with shown on the display).
Note: If you exit the CONFIG menu by pressing the is canceled.
SKIP CLR
37
P
DOWN
Call up the CHECKER screen. M NAME Press the RFC . The RF CHECK menu will appear. Point the arrow at CHECKER using the dial or UP/DOWN key, and then press the TF ENT key.
SET MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
SCN
MIC
4
AUTO
MW
KL
6 9
RF C H E C K CHECKER Ca l l Wa i t
SCRT
7
PRIO
8
CTCSS
TF
SKIP
CLR
REC
0
F TUNE
ENT
MIC
DJ-X2
Measure the electric field strength. As the electric field strength increases, the S-meter shows higher levels with faster beeping. RF C H E C K
CHECK I NG
Note: Since the electric-field meter is intended to measure the nearby strong electric field strength, it reacts at the sensitivity of approximately -50 dBm minimum. The sensitivity varies depending on the frequency.
1
P
DOWN
Call up the CALL WAIT screen. M NAME Press the RFC key. The RF CHECK menu will appear. Point the arrow at CALL WAIT using the dial or UP/DOWN key, and then TF press the ENT key.
SET MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
SCN
MIC
4
AUTO
MW
KL
6 9
RF C H E C K CHECKER Ca l l Wa i t
SCRT
7
PRIO
8
CTCSS
TF
SKIP
CLR
REC
0
F TUNE
ENT
MIC
DJ-X2
Set up the set level mode. Set the level by selecting a number from 1 through 9 (the initial setting is 3) using the dial, the UP/DOWN key, or a numeric key.
R F CA L L L V L 3
C A L L WA I T I NG
When the electric field strength exceeds the set level, the buzzer sounds with {bell icon} blinking on the display. The buzzer sounds for 10 seconds and {bell icon} continues to blink. Canceling the set level mode SKIP If you press the CLR key when is blinking, this blinking stops. SKIP NAME If is not blinking, pressing the CLR or MRFC key cancels this mode.
LAMP
Note:
38
1
F
MO NI SRC H LAM P
Call up the BATT VOLT screen. Press the F key, and then SET BAT T VOL T press the HELP key with 4 . 9V shown on the display. The BATT VOLT menu will appear. Point the arrow at +CONFIG using the dial or TF UP/DOWN key, and then press the ENT key. The CONFIG menu will appear. Point the arrow at +BATT VOLT using the dial or UP/DOWN key, and then press TF the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
MIC
AUTO
MW
KL
The battery voltage will be shown on the display. SKIP If you press the CLR key, the battery voltage disappears.
Note: The measured value is updated every 0.5 second. If an external power source (10-16 V) is used, OVER 8V is displayed.
1
F
MO NI SRC H LAM P
Call up the TONE screen. Press the F key, and then press SET TONE the HELP key with shown on H i gh the display. L OW The TONE menu will appear. Point the arrow at +CONFIG using the dial or UP/DOWN TF key, and then press the ENT key. The CONFIG menu will appear. Point the arrow at TF +TONE and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
MIC
AUTO
MW
KL
Set the reception tone. Point the arrow at High or Low using the dial or UP/DOWN key, and then press TF the ENT key (the initial setting is High). The display will return to the CONFIG menu. Point the arrow at END and then TF press the ENT key (Alternatively, you may press the F key, and then press the TF key with shown on the display).
ENT
Note:
SKIP CLR
39
1
F
MO NI SRC H LAM P
Call up the BELL screen. Press the F key, and then SET BEL L press the HELP key with OF F shown on the display. ON The BELL menu will appear. Point the arrow at +CONFIG using the dial or UP/DOWN TF key, and then press the ENT key. The CONFIG menu will appear. Point the arrow at TF +BELL and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
MIC
AUTO
MW
KL
Turn the BELL mode ON/OFF. Point the arrow at ON or OFF using the dial or UP/DOWN key, and then press TF the ENT key (the initial setting is OFF). When squelch is canceled, the buzzer sounds for 10 seconds and starts SKIP blinking. Pressing the CLR key cancels this blinking. The display will return to the CONFIG menu. Point the arrow at END and then TF press the ENT key (Alternatively, you may press the F key, and then press TF the ENT key with shown on the display).
Note: If you exit the CONFIG menu by pressing the is cancelled.
SKIP CLR
1
F
MO NI SRC H LAM P
Call up the OPENINGMG screen. Press the F key, and then press SET 1 L I NE MSG the HELP key with shown on A BCDE FGH I J K the display. A L I NCO The menu will appear. Point the TF arrow at +CONFIG and then press the ENT key. The CONFIG menu will appear. Point the arrow at TF +OpeningMG and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
MIC
MW AUTO
KL
40
Enter a message. Select each character by turning the dial, and then establish it by pressing the DOWN key. Pressing the UP key allows you to cancel the established character. Up to 36 characters may be entered (the initial setting is ALINCO INTELLIGENT RECEIVER). Finish the setting. After you have finished entering the characters, press the
TF ENT
key.
The display will return to the CONFIG menu. Point the arrow at END and then TF press the ENT key (Alternatively, you may press the F key, and then press the TF shown on the display. ENT key with
SKIP
Note:
If you exit the CONFIG menu by pressing the CLR key, the changed setting is canceled. If you turn the dial while holding down the F key, you can move 11 characters ahead.
CLN
T RX/S ER POW
F
MO NI SR
VOL
PMS
SET
MR MW
While holding down the F key, turn ON the power. When the DJUSER RESET CANCE L X2000 starts up, the USER RESET S Y S T EM menu will appear on the display. Move the arrow to the reset command you want, using TF the dial or the UP/DOWN key. Then, press the ENT key. Reset commands are described here following.
SQL
Cancels the reset command entirely. Initializes user-set functions, but it does not clear memory channels. (Choose this normally.) Clears all functions and memories including factory-set bandplan.
CAUTION:
It takes time to complete the resetting. Do not turn ON the power during the resetting.
41
STEP
2
ATT
3
HELP RF C
M NAME A-B S
SCN
MIC
4
AUTO
MW
KL
6 9
SCRT
7
PRIO
8
CTCSS
TF
SKIP
CLR
REC
0
F TUNE
ENT
MIC
DJ-X2
VFO A=B
or
MRMW
keys.
1
F
MO NI SRC H LAM P
Call the SCAN menu. Press the F key, and then press SET SCAN the HELP key with shown on SCAN MODE the display. BUS Y T i me r The SCAN menu will appear. Point the arrow at +CONFIG using the dial or UP/DOWN TF key, and then press the ENT key. The CONFIG menu will appear. Point the arrow at TF +SCAN and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
MIC
MW AUTO
KL
Call up the SCAN MODE screen. Point the arrow at +SCAN MODE using the dial or TF UP/DOWN key, and then press the ENT key.
42
Select a scanning option. Point the arrow at the desired option using the dial or UP/DOWN key, and then TF press the ENT key. The available scanning options are described below (the initial setting is BUSY): BUSY Busy scan. The DJ-X2000 stays on any signal it locates until the signal vanishes. Once the signal dis appeares, scanning is resumed. STOP The DJ-X2000 stops scanning on the first signal it locates. Scanning is not resumed after the signal vanishes. TIMER When the currently transmitted signals of any frequency are received, scanning is paused for a given period of time. After this specific time period, scanning is resumed even if the signals are being received. For setting the pause period, see 3.1.17 Setting the scanning pose period (page 45). The display will return to the SCAN menu. Point the arrow at END using the dial TF or UP/DOWN key, and then press the ENT key (Alternatively, you may press the TF key, and then press the ENT key with shown on the display).
Note: If you exit the SCAN menu by pressing the <CLR> menu, the changed setting is canceled.
1
F
MO NI SRC H LAM P
Call up the SCAN menu. Press the F key, and then press SET SCAN the HELP key with shown on SCAN MODE the display. BUS Y T i me r The SCAN menu will appear. Point the arrow at +CONFIG using the dial or UP/DOWN TF key, and then press the ENT key. The CONFIG menu will appear. Point the arrow at TF +SCAN SETUP and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
MIC
MW AUTO
KL
Call up the S_LEVEL menu. Move the arrow to +S_LEVEL using the dial or the TF UP/DOWN key, and then press the ENT key.
S LEVEL OFF ON
43
Select an S-meter level. Point the arrow at ON using the UP/DOWN key. Select a level from 1 through 7 TF using the dial, and then press the ENT key. If you do not want to select any STF meter level, select OFF and then press the ENT key (the initial setting is OFF). Higher levels require stronger signals to stop scanning. The display will return to the SCAN mode. Point the arrow at END and then TF press the ENT key (Alternatively, you may press the F key, and then press TF the ENT key with shown on the display).
Note: If you exit the SCAN menu by pressing the canceled.
SKIP CLR
1
F
MO NI SRC H LAM P
Call up the SCAN menu. Press the F key, and then press SET the HELP key with shown on SCAN SCAN MODE the display. BUS Y T i me r The SCAN menu will appear. Point the arrow at +CONFIG using the dial or UP/DOWN TF key, and then press the ENT key. The CONFIG menu will appear. Point the arrow at TF +SCAN SETUP and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
MIC
AUTO
MW
KL
2 3
Call up the BUSY TIMER screen. Point the arrow at +Busy Timer and then press the TF ENT key.
B u s y T i me r 5s
Set the scanning pause period. Set the scanning pause period using the dial or UP/DOWN key, and then press TF the ENT key (the initial setting is 5s). The display will return to the SCAN menu. Point the arrow at END and then TF press the ENT key (Alternatively, you may press the F key, and then press the shown on the display).
Note: If you exit the SCAN menu by pressing the canceled.
SKIP CLR
44
VOL
PMS
SET
DOWN
UP
VFO A B
MR MW
NFM A 145 . 34 b 8 .
SQL
SET MODE
1
STEP
2
ATT
3
HELP
M NAME
RF C
MIC
4
AUTO
5
MW
KL
6
A-B S
SCN
SCRT
7
PRIO
8
CTCSS
9
TF
ENT
SKIP
REC
F TUNE
Turn the priority feature OFF. PRIO Press the F key, and then press the 8 key with shown on the display. PRI shown at the top of the screen will disappear showing that the priority feature is turned OFF.
Note: If the priority feature is ON, the CH SCOPE mode is disabled.
1
F
MO NI SRC H LAM P
Call up the PRIO menu. Press the F key, and then SET PR I O press the HELP key with PR I F REQ shown on the display. PR I MODE The PRIO menu will appear. Point the arrow at +PRIO using the dial or UP/DOWN TF key, and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET MODE
1
STEP
2
ATT
3
HELP
M NAME
RF C
MIC
MW AUTO
KL
A-B S
45
Call up the PRI MODE screen. Point the arrow at +PRI MODE using the dial or TF UP/DOWN key, and then press the ENT key.
Select a priority option. Select a priority option using the dial or UP/DOWN key, and then press TF the ENT key. The available options are listed below (the initial setting is STOP). BUSY When signal is received on the priority channel, the DJ-X2000 stays on the priority frequency until ithe signal vanishes. STOP When signal is received on the priority channel, the DJ-X2000 stays on the priority frequency even after the signal vanishes. TIMER Once signals are received on the priority channel, they will be received for a given interval. For specifying this interval, see 3.1.21 Specifying a priority interval (page 48). The display will return to the PRIO menu. Point the arrow at END using the dial TF or UP/DOWN key, and then press the ENT key (Alternatively, you may press the TF shown on the display). F key, and then press the ENT key with
Note: If you exit the PRIO menu by pressing the is canceled.
SKIP CLR
1
F
MO NI SRC H LAM P
Call up the PRIO menu. Press the F key, and then press SET the HELP key with shown on PR I O PR I F REQ the display. PR I MODE The PRIO menu will appear. Point the arrow at +PRIO using the dial or UP/DOWN TF key, and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET MODE
1
STEP
2
ATT
3
HELP
M NAME
RF C
MIC
AUTO
MW
KL
A-B S
Call up the PRIO FREQ screen. Point the arrow at +PRIO FREQ and then press the TF ENT key.
46
Call up the PRI MEMORY screen. Point the arrow at +MEMORY using the dial or TF UP/DOWN key, and then press the ENT key.
3 4
PR I MEMORY 8 .
Select a channel. TF Select the desired memory bank and channel, and then press the ENT key. The memory bank can be selected from A through E using the F TUNE key. The bank number can be selected using the dial or a numeric key. Pressing the UP/DOWN key moves the arrow, allowing you to select the channel number with the dial or a numeric key.
The display will return to the PRI FREQ screen. Point the arrow at END and then TF press the ENT key (Alternatively, you may press the F key, and then press the TF shown on the display). ENT key with
Note: To select the currently received frequency for the priority channel, point the TF arrow at NOW FREQ in step 2 and then press the ENT key (the initial setting is NOW FREQ). TF If you point the arrow at NOW PRI and press the ENT key, the frequency currently selected for the priority channel is displayed. If you exit the PRI FREQ screen, the changed setting is canceled.
1
F
MO NI SRC H LAM P
Call up the PRIO menu. Press the F key, and then press SET the HELP key with shown on PR I O PR I F REQ the display. PR I MODE The PRIO menu will appear. Point the arrow at +PRIO using the dial or UP/DOWN TF key, and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET MODE
1
STEP
2
ATT
3
HELP
M NAME
RF C
MIC
AUTO
MW
KL
A-B S
Call up the PRI TIMER screen. Point the arrow at +PRI TIMER and then press the TF ENT key.
PR I T i me r 5s
47
Specify a priority interval. Specify a priority interval in a range between 1 and 12 seconds in 1-second TF steps using the UP/DOWN key, and then press the ENT key (the initial setting is 5s). The display will return to the PRIO menu. Point the arrow at END and then press TF the ENT key (Alternatively, you may press the F key, and then press the TF shown on the display). ENT key with
Note: If you exit the PRIO menu by pressing the canceled.
SKIP CLR
1
F
MO NI SRC H LAM P
Call up the CH SCOPE menu. Press the F key, and then SET press the HELP key with CH SCOPE I N T ERV A L shown on the display. CON T I NUE The CH SCOPE menu will appear. Point the arrow at +CONFIG using the dial or TF UP/DOWN key, and then press the ENT key. The CONFIG menu will appear. Point the arrow at +CH TF SCOPE and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
MIC
AUTO
MW
KL
48
Select a search resuming option. Point the arrow at the desired option using the dial or UP/DOWN key, and then TF press the ENT key. The available options are described below (the initial setting is INTERVAL): SRCH SINGLE The search is carried out only once when the key is pressed. It is not carried out a second time until the first SRCH search is turned canceled and the key is pressed again. INTERVAL A search is carried out once every 10 seconds updating the spectrum condition. Sound is muted the moment the search takes place. CONTINUE Searching is continuous and the spectrum condition is renewed continuously. In this case, no sound is heard from the DJ-X2000. The display will return to the CH SCOPE menu. Point the arrow at END and then TF press the ENT key (Alternatively, you may press the F key, and then press the TF key with shown on the display). ENT
Note: If you exit the CH SCOPE menu by pressing the setting is canceled.
SKIP CLR
1
F
MO NI SRC H LAM P
Call up the F TUNE screen. Press the F key, and then press SET FLASH TUNE the HELP key with shown on F L A SH T U N E the display. F. COUNTER The F TUNE screen will appear. Point the arrow at +SPECIAL using the dial or TF UP/DOWN key, and then press the ENT key. The SPECIAL screen will appear. Point the arrow at +F TF TUNE (+FLASH TUNE) and then press the ENT key.
R POWE
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
SCN
MIC
4
MW AUTO
5
KL
6 9
SCRT
7
PRIO
8
CTCS
TF
SKIP
REC
0
F TUNE
ENT
CLR
MIC
X2
49
Select the Flash tune. Point the arrow at the desired option using the dial or UP/DOWN key, and then TF press the ENT key (the initial setting is F TUNE). F TUNE Instantaneously checks for a radio frequency and automatically tunes in to the detected frequency. F COUNTER Check for a radio frequency and shows the detected frequency in real time (the frequency resolution is 100 Hz). Starting the Flash tune Press the F key, and then press the shown on the display. The Flash tune will start.
POWE R
F TUNE
key with
MO NI
VOL
PMS
SET
SQL
SRC H
MR MW
LAM P
DOWN
UP
VFO A B
SET MODE
1
STEP
2
ATT
3
HELP
Pressing the
SKIP CLR
M NAME
RF C
MIC
4
AUTO
5
MW
KL
6
A-B S
SCN
SCRT
7
PRIO
8
CTCSS
9
TF
ENT
SKIP
CLR
REC
0
F TUNE
Note:
The operating frequencies in the F TUNE and F COUNTR modes ranges from approximately 50 MHz to 1300 MHz. The Flash tune starts with input of approximately -30 dB or more. However, if there is any strong radio or noise than the targeted radio, the Flash tune may not be activated depending on the frequency condition. This function is not applicable to intermittent radio in intervals of 0.1 second or less, such as digital radio. The Flash tune is not valid for radio that fluctuates by 1 kHz or more. If the Flash tune is set during scanning in the PMS or MR mode, the scanning is canceled.
50
3.1.24 Descrambler
This function descrambles the scrambled voice signals.
Note: Only the NFM type radio signals can be descrambled.
1
F
MO NI SR C H P
LA M
Call up the SET SCRAMBLE screen and then turn ON the Descrambler. Press the F key, and then press SCRT the 7 key with shown on the display. OFF ON 4 The SET SCRAMBLE screen will appear. Point the arrow at ON using the UP/DOWN key.
R POWE
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET MODE
1
STEP
2
ATT
3
HELP
M NAME
RF C
MIC
4
AUTO
5
MW
KL
6
A-B S S
SCN
SCRT
7
PRIO
8
CTCS
9
TF
ENT
SKIP
R
REC
0
F TUNE
Control the carrier. With the arrow pointing at ON, set the carrier to the state where the voice can be recognized. The carrier can be increased or decreased in a range between 0 and 125 (the initial setting is 40). TF If you press the ENT key with the arrow pointing at ON, the normal screen appears with the Descrambler being active. Canceling the Descrambler SKIP Press the CLR key. This will cancel the Descrambler. Priority in comparison with the CTCSS decoding function and A/B squelch The Descrambler cannot be used with the CTCSS decoding function or A/B squelch. If the A/B squelch is turned ON when the Descrambler is active, the A/B squelch takes priority. The CTCSS decoding function cannot be used when the Descrambler or A/B squelch is active. If the Descrambler is turned ON when the CTCSS decoding function is active, the CTCSS decoding function remains disabled until the Descrambler is turned OFF.
Note: If you press the ENT key to display the normal screen when the Descrambler is active, the Descrambler is disabled for any radio type other than the NFM. If VOL is blinking on the display when the Descrambler is active, the sound volume can be controlled.
TF
51
Setting the reception of CTCSS signals Specify the reception frequency of CTCSS signals and turn ON/OFF the reception.
1
F
MO NI SRC H P LAM
Call up the CTCSS MANUAL screen. Press the F key, and then press CTCSS the 9 key with shown on CTCSS MANUAL OFF the display. ON 8 8 . 5 H z The CTCSS SET menu will appear. Point the arrow at +MANUAL using the dial or TF UP/DOWN key, and then press the ENT key.
R POWE
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
SCN
MIC
4
MW AUTO
5
KL
6
SCRT
7
PRIO
8
S CTCS
9
TF
ENT
SKIP
R
REC
0
F TUNE
Select the reception frequency of CTCSS signal. Point the arrow at ON using the UP/DOWN key, and then select the reception frequency of CTCSS signals using the dial. The range of selectable frequencies is between 76 and 254 Hz (the initial setting is 88.5 Hz). If you do not want to receive CTCSS signals, select OFF. TF Press the ENT key to complete the setting. Priority order in comparison with the Descrambler and A/B squelch The CTCSS decoding function cannot be used with the Descrambler or A/B squelch. If the Descrambler or A/B squelch is active, the CTCSS decoding function is disabled. If the Descrambler or A/B squelch is turned ON when the CTCSS decoding function is active, the CTCSS decoding function is disabled during its use.
Note: In the PMS or MR mode, when DIRECT WR is turned ON, this setting is possible (the initial setting is ON). For further details, see 3.3.31 Directly changing the settings (page 63).
52
1
F
MO NI S RC H P LA M
Call up the CTCSS SET menu. Press the F key, and then press CTCSS the 9 key with shown on the display. The CTCSS SET menu will appear.
R POWE
VOL
PMS
SET
DOWN
UP
VFO A B
MR MW
SQL
SET MODE
1
STEP
2
ATT
3
HELP
M NAME
RF C
MIC
4
MW AUTO
5
KL
6
A-B S
SCN
SCRT
7
PRIO
8
S CTCS
9
TF
ENT
SKIP
R
REC
0
F TUNE
Start scanning Point the arrow at CTCSS SCAN using the dial or UP/DOWN key, and then TF press the ENT key. This will start scanning. Once CTCSS signals are detected, the scanning stops. CTCSS reversing This function is used to reverse the CTCSS decoding function. When it is set to ON, CTCSS signals of a mismatching frequency are received while those of a matching frequency are not received.
1
F
MO NI S RC H P LAM
Call up the CTCSS REVERSE screen. Press the F key, and then press CTCSS REVERSE the 9 key with shown on OF F the display. ON The CTCSS SET menu will appear. Point the arrow at REVERSE using the dial or TF UP/DOWN key, and then press the ENT key.
R POWE
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP
M NAME
RF C
MIC
4
MW AUTO
5
KL
6
A-B S S
SCN
SCRT
7
PRIO
8
CTCS
9
TF
ENT
SKIP
R
REC
0
F TUNE
Select ON/OFF for the CTCSS reversing function. Point the arrow at ON or OFF using the dial or UP/DOWN key, and then press TF the ENT key.
Note: This function may fail if signals are too weak or include too many noises.
53
1
F
MO NI SRC H LAM P
Call up the A/B SQ SET screen. Press the F key, and then press SET the HELP key with shown on A / B SQ SET OF F the display. ON The menu will appear. Point the arrow at +SPECIAL using the dial or UP/DOWN key, TF and then press the ENT key. The SPECIAL menu will appear. Point the arrow at +A/B TF SQ SET and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
MIC
AUTO
MW
KL
Select ON/OFF for A/B squelch. Point the arrow at ON or OFF using the dial or UP/DOWN key, and then press TF the ENT key (the initial setting is OFF). ON If modulation signals of 2300 Hz used for free-line signals are detected, the squelch is activated and the sound is muted. If those signals are no longer detected, the squelch is canceled. OFF The A/B squelch is disabled. Priority order in comparison with the Descrambler and CTCSS decoding function The A/B squelch cannot be used with the Descrambler or CTCSS decoding function. If the A/B squelch is turned ON when the Descrambler is active, the A/B squelch takes priority. If the Descrambler or A/B squelch is active, the CTCSS decoding function is disabled. If the A/B squelch is turned ON when the CTCSS decoding function is active, the CTCSS decoding function is canceled during its use.
Note: This function may fail if radio or modulation signals are too weak or include too many noises. It is not applicable to free-line signals of any frequency other than 2300 Hz.
54
3.1.27 Transweeper
This function is used to detect a wireless microphone or any other bug using radio and locate the place where it is installed. If you previously assign any frequency expected for bugging purposes to the memory channel or auto memory channel, the DJ-X2000 will scan for that frequency. The settings for bank link and channel skipping will become valid.
1
F
MO NI SRC H LAM P
Turn ON the transweeper. Press the F key, and then press TF the ENT key with shown on TF the display. NO F OUND The transweeper will start. The scanning varies depending on the basic mode in use.
RX/ST POWE R
VOL
PMS
SET
SQL
MR MW
DOWN
UP
VFO A B
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
SCN
MIC
4
AUTO
MW
KL
6 9
SCRT
7
PRIO
8
CTCSS F TUNE
TF
ENT
SKIP
CLR
REC
0
MIC
X2
VFO mode
MR mode
PMS mode
The scanning is performed from the currently received frequency toward higher frequencies. The scanning direction is changed using the dial or UP/DOWN key. Only the specified bank is scanned. The settings for bank link and channel skipping become valid. Pressing A~B S the SCN key starts the scanning. The scanning is performed only within the programmed scanning range that you have specified.
Check for bugging. In this state, control the sound volume and the orientation of the DJ-X2000. If the existence of any bug is detected, the display changes as shown here.
( ,, )
A1
154 .
Search for the location of the bug while slowly bringing the DJ-X2000 closer to that bug. You can find the distance to the location of the bug according to the changes on the display. As the DJ-X2000 comes closer to the bug
( ,, )
A1
154 .
55
( ,, )
A1
154 .
The number of I shown at the lower right corner of the display tells you the distance to the location of the bug. Each I represents approximately 1 m. For example, 5 I show that the bug is located more than 5 m away.
( ,, )
A1
154 .
Note:
If no bug is found after the specified range has been scanned, the message NO FOUND appears on the display.
CAUTION:
The effective range of sound monitoring for bugs is normally between approximately 1 m and 5 m. The transweeper is greatly affected by the intensity of radio from the bug and the sensitivity of the microphone. It may malfunction or fail depending on the ambient conditions (where there are too many echoes). If the DJ-X2000 is suddenly moved during its transweeper process, the Doppler effect causes a malfunction. The transweeper may not work normally depending on the relation between the orientation of the speaker and the location of the bug. This function does not work normally when radio with modulation signals of 2300 Hz is received.
56
1
F
MO NI SRC H LAM P
Call up the REC screen. Press the F key, and then press SET REC the HELP key with shown on RX A F the display. MIC The menu will appear. Point the arrow at +SPECIAL using the dial or UP/DOWN key, TF and then press the ENT key. The SPECIAL screen will appear. Point the arrow at TF +REC and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
STEP
2
ATT
3
HELP RF C
M NAME
KL
Select the received sound or the sound from the speaker. Point the arrow at the desired option using the dial or UP/DOWN key, and then TF press the ENT key (the initial setting is MIC). RX AF The received sound is recorded. MIC The sound from the speaker is recorded. The display will return to the SPECIAL screen. Point the arrow at END and then press the F key (Alternatively, you may press the F key, and then press the TF key with shown on the display). ENT Recording the sound
1
F
MO NI SRC H LAM P
Call up the recording screen. Press the F key, and then press REC the 0 key with shown on the display. The recording screen will appear.
POWE R
VOL
PMS
SET
MR MW
DOWN
UP
VFO A B
SQL
SET MODE
1
STEP
2
ATT
3
HELP
M NAME
RF C
MIC
4
AUTO
5
MW
KL
6
A-B S
SCN
SCRT
7
PRIO
8
CTCSS
9
TF
ENT
SKIP
CLR
REC
0
F TUNE
MIC
J X2
Start the recording MODE Press the 1 key. The recording will start and the elapsed time will appear on the display. The sound can be recorded for 160 seconds maximum.
RECORD I NG
5s
57
Stop or pause the recording. STEP To stop the recording, press the 2 key. F TUNE To pause (temporarily stop) the recording, press the key. If you press the F TUNE key again, the recording is resumed. When the recording time reaches 160 seconds, END appears on the display and the recording stops automatically. Exit the recording mode. SKIP Press the CLR key.
Note: Only a single session of sound can be recorded. No other function can be used during the recording. The sound volume can be controlled in the recording mode. Sound can be repeatedly recorded approximately 10,000 times. The RX AF recording starts when sound signal is received.
1
F
MO NI SRC H LAM P
Call up the recording screen. Press the F key, and then press REC the 0 key with shown on the display. The recording screen will appear.
POWE R
VOL
PMS
SET
MR MW
DOWN
UP
VFO A B
SQL
SET MODE
1
STEP
2
ATT
3
HELP
M NAME
RF C
MIC
4
AUTO
5
MW
KL
6
A-B S
SCN
SCRT
7
PRIO
8
CTCSS
9
TF
ENT
SKIP
CLR
REC
0
F TUNE
MIC
J X2
2 3
Start the playback. ATT Press the 3 key. The playback will start and the elapsed time will appear on the display.
PLAY I NG
5s
Stop or pause the playback. STEP To stop the playback, press the 2 key. F TUNE To pause (temporarily stop) the playback, press the key. F TUNE If you press the key again, the playback is resumed. After all the recorded sound has been played back, END appears on the display and the playback stops automatically.
58
1
F
MO NI SRC H LAM P
Call up the recording screen. Press the F key, and then press REC the 0 key with shown on the display. The recording screen will appear.
POWE R
VOL
PMS
SET
MR MW
DOWN
UP
VFO A B
SQL
SET MODE
1
STEP
2
ATT
3
HELP
M NAME
RF C
MIC
4
AUTO
5
MW
KL
6
A-B S
SCN
SCRT
7
PRIO
8
CTCSS
9
TF
ENT
SKIP
CLR
REC
0
F TUNE
MIC
J X2
2 3
Erase the recorded data. REC Press the 0 key. The recorded data will be erased. Exit the recording mode. SKIP Press the CLR key.
1 2
F
MO NI SRC H LAM P
Connect an earphone or external speaker to the SP terminal on the top of the DJ-X2000. Start picking up sound. Press the F key, and then press MIC the 4 key with shown on the display. The sound pickup will start.
POWE R
VOL
PMS
SET
MR MW
DOWN
UP
VFO A B
SQL
SET MODE
1
STEP
2
ATT
3
HELP
M NAME
RF C
MIC
4
AUTO
5
MW
KL
6
A-B S
SCN
SCRT
7
PRIO
8
CTCSS
9
TF
ENT
SKIP
CLR
REC
0
F TUNE
MIC
J X2
59
1
F
MO NI SRC H LAM P
Call up the TRANCEIVER screen. Press the F key, and then SET press the HELP key with TR shown on the display. PTT The TRANCEIVER menu will appear. Point the arrow at +SPECIAL using the dial or TF UP/DOWN key, and then press the ENT key. The SPECIAL menu will appear. Point the arrow at TF +TRANCEIVER and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
SCN
MIC
4
AUTO
MW
KL
6
CTCSS
Set the function of the PTT (SRCR) key. Point the arrow at +PTT MODE using the dial or TF PTT UP/DOWN key, and then press the ENT key. OF F The PTT MODE screen will appear. Point the arrow at TF ON OFF or ON and then press the ENT key. OFF Transmission is performed while the PTT (SRCH) key is being held down. ON Pressing the PTT (SRCH) key toggles between transmission and reception. The display will return to the TRANCEIVER menu.
Activate the transceiver function. Point the arrow at +TR MODE using the dial or UP/DOWN key, and then press TF the ENT key. The transceiver function will be activated.
Note: The transceiver function is only available in the World version.
60
Select the frequency you want to receive. The frequency can be selected using the dial or UP/DOWN key. However, the following limitations apply: Radio type NFM only Frequency range 250.000 MHz to 259.975 MHz Frequency step Fixed at 25 kHz When F is shown on the display by pressing the key, the frequency can be increased or decreased in steps of 250 kHz using the dial or UP/DOWN key.
Perform transmission. SRCH In the TRANCEIVER mode, the key located on the F left side of the DJ-X2000 works as the PTT key. MO NI If you speak to the microphone when the PTT key is ON, SRC H the voice can be transmitted at the currently received LAM P frequency. The status of the PTT key can be selected from ON and OFF.
R ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
SCN
MIC
4
AUTO
5
MW
KL
6
CTCSS
Note:
Since the transmission uses only weak signals, no license for an amateur radio station or the like is required. For the same reason, no antenna for weak transmission is connected to the BNC connector.
61
1
F
MO NI SRC H LAM P
Call up the DIRECT WR screen. Press the F key, and then press SET D I RECT WR the HELP key with shown on ON the display. OFF The menu will appear. Point the arrow at +CONFIG using the dial or UP/DOWN key, and TF then press the ENT key. The CONFIG screen will appear. Point the arrow at TF +DIRECT WR and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
SCN
MIC
4
AUTO
MW
KL
6
CTCSS
Selecting ON/OFF for DIRECT WR. Point the arrow at ON or OFF using the dial or UP/DOWN key, and then press TF the ENT key (the initial setting is OFF). The display will return to the CONFIG screen. Point the arrow at END and then TF press the ENT key (Alternatively, you may press the F key, and then press the TF key with shown on the display). ENT
Note: If you exit the CONFIG screen by pressing the settings are canceled.
SKIP CLR
62
1
F
MO NI
SRC H LAM P
Call up the LINK SET screen. Specify frequencies in bands A and B of VFO. Press the F key, and then press SKIP the CLR key with shown on the display.
RX/ST POWE R
VOL
PMS
SET
MR MW
DOWN
UP
VFO A B
L I NK SET AU T O L I NK US ER L I NK
SQL
SET
MODE
1
STEP
2
ATT
3
HELP
M NAME
RF C
MIC
4
AUTO
5
MW
KL
6
A-B S
SCN
SCRT
7
PRIO
8
CTCSS
9
TF
ENT
SKIP
CLR
REC
0
F TUNE
MIC
DJ-X2
Select a type of the VFO link function. Point the arrow at the desired option using the dial or UP/DOWN key, and then TF press the ENT key (the initial setting is LINK OFF). AUTO LINK USER LINK The frequencies in bands A and B interlock and change at the interval that was set using the auto link function. Both bands A and B are displayed in capital letters and the VFO link function becomes active. As the frequency on the upper line of the display is changed, the one on the lower line changes simultaneously. The VFO link function is canceled.
LINK OFF
Note:
The frequency on the upper line may exceed 2149.999950 MHz (the upper limit for the DJ-X2000) when it is changed. In this case, press the
VFO A=B
key
toggle between bands A and B. The band shown on the upper line will be switched to the lower line. The band shown on the lower line (exceeding 2149.9999 MHz) will be included in a range between 0.1 MHz and 2149.999 MHz and then switched to the upper line while maintaining the difference between the two frequencies. The VFO link function is not canceled.
63
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
MIC
4
MW AUTO
5
KL
6
SCRT
PRIO
CTCS
9
SCN
TF
Scanning direction can be changed using the dial or the UP/DOWN key. To cancel AB scan A~B S Press the SCN key. This will cancel AB scanning.
1 2
F
MO NI SR C H P LAM
Press the key to get the MR mode. Then set the memory bank No. and channel No. you want . Copy the frequency into the VFO.
R POWE
VOL
PMS
SET
DOWN
UP
VFO A B
MR MW
Press the F key to display , followed by the key. The frequency in the selected memory channel will be displayed on the upper line (currently used) band.
VFO A=B
SQL
SET MODE
1
STEP
2
ATT
3
HELP
M NAME
RF C
IC
MW AUTO
KL
A-B S
64
1 2
F
MO NI SRC H P LAM
Press the key to get the PMS mode. Then set the program bank No. you want to display in the VFO mode. Copy the frequency into the VFO.
R POWE
VOL
PMS
SET
DOWN
UP
VFO A B
MR MW
Press the F key to display , followed by the key. The frequency in the selected program bank will be displayed on the upper line (currently used) band the instant that scanning picks it up.
VFO A=B
SQL
SET MODE
1
STEP
2
ATT
3
HELP
M NAME
RF C
IC
AUTO
MW
KL
A-B S
65
1
F
MO NI SRC H LAM P
Call up the PMS SET screen. Press the F key, and then press SET S e t PMS BANK the HELP key with shown on P ---- . ---the display. -------The menu will appear. Point the arrow at +PMS using the dial or UP/DOWN key, and TF then press the ENT key. The PMS screen will appear. Point the arrow at +PMS TF SET and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
MIC
MW AUTO
KL
Select the bank on which you want to store the scanning program. Using the dial or numeric keys, select the bank on which TF you want to store the scanning program. Press the ENT S e t PMS BANK F TUNE p1 ---- . ---key (Pressing the key toggles between the -------uppercase P and the lowercase p).
3 4 5
Specify the frequency to start the scanning. Using numeric keys, enter the frequency at which you TF want to start the scanning. Press the ENT key.
Specify the frequency to end the scanning. Using numeric keys, enter the frequency at which you TF want to end the scanning. Press the ENT key.
Select a radio type. Point the arrow at the desired radio type using the dial or TF UP/DOWN key, and then press the ENT key.
66
6 7
Select a frequency step. Point the arrow at the desired frequency step using the TF dial or UP/DOWN key, and then press the ENT key.
STEP 1 KHz AU TO S T E P 5 Hz
Give a name to the program. Select each character by turning the dial and then establish it by pressing the DOWN key. The established character can be canceled by pressing the UP key. Up to 8 characters may be entered for the name.
Store the scanning program. TF After you have finished entering the name, press the ENT key. The display will return to the PMS menu. Point the arrow at END and then press the TF TF ENT key (Alternatively, you may press the F key, and then press the ENT key with shown on the display).
Note: In naming the program, you can move 11 characters ahead by turning the dial while holding down the F key.
SCRT
7
PRIO
8
CTC
TF
SKIP
REC
0
F TUNE
ENT
CLR
MIC
key to display
SKIP CLR
MO NI SRC H LAM P
VOL
PMS
SET
DOWN
UP
VFO A B
MR MW
SET MODE
1
STEP
2
ATT
3
HELP
M NAME
RF C
MIC
4
MW AUTO
5
KL
6
A-B S
SCN
SCRT
7
PRIO
8
CT
CSS
9
TF
ENT
SKIP
CLR
REC
0
F TUNE
MIC
T LIGEN INTELCEIVER RE
DJ-X2
PASS ED I T followed by the key. This will 85 . 1 display the PASS EDIT display. 153 . 6 Then move the arrow to pass frequency settings you want to clear, using the dial or REC the UP/DOWN keys, and press the 0 key. The selected frequency will be disappear from the display. TF Press the ENT key to exit.
SQL
67
1
F
MO NI SRC H LAM P
Call up the PMS LINK screen. Press the F key, and then press SET PMS Ba n k L i n k the HELP key with shown on P ---------the display. p ---------The menu will appear. Point the arrow at +PMS using the dial or UP/DOWN key, and TF then press the ENT key. The PMS screen will appear. Point the arrow at +PMS TF LINK and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
MIC
AUTO
MW
KL
Enter a program bank number. Using a numeric key, enter the program number you want to link. Pressing the F TUNE key toggles between the uppercase P and the lowercase p. To link all the programs, enter all the numbers from 0 to 9. TF After you have finished entering the number(s), press the ENT key. The display will return to the PMS menu. Point the arrow at END and then press TF TF the ENT key (Alternatively, you may press the F key, and then press the ENT key with shown on the display).
1
F
MO NI SRC H LAM P
Call up the PMS EDIT screen. Press the F key, and then press SET PMS ED I T the HELP key with shown on CO P Y the display. MO V E The menu will appear. Point the arrow at +PMS using the dial or UP/DOWN key, and TF then press the ENT key. The PMS screen will appear. Point the arrow at +PMS TF EDIT and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
MIC
MW AUTO
KL
Call up the COPY screen. Point the arrow at +COPY using the dial or UP/DOWN TF key, and then press the ENT key. P
C O P Y F R OM
82 .
68
3 4
Select a source program. Using the dial or a numeric key, select the program you TF F TUNE want to copy. Press the ENT key (pressing the key toggles between the uppercase P and lowercase p). Select a destination program. Using the dial or a numeric key, select the program to which you want to copy the source program. Press the TF F TUNE key toggles between the ENT key (pressing the uppercase P and the lowercase p).
SKIP CLR
C O P Y F R OM
P1
145 . 34
COPY TO
P2 ---- . -----------
key.
The display will return to the PMS EDIT screen. Point the END and then press TF TF the ENT key (Alternatively, press the F key, and then press the ENT key with shown on the display).
1
F
MO NI SRC H LAM P
Call up the PMS EDIT screen Press the F key, and then press SET the HELP key with shown on PMS ED I T the display. CO P Y The menu will appear. Point the MO V E arrow at +PMS using the dial or TF UP/DOWN key, and then press the ENT key. The PMS screen will appear. Point the arrow at +PMS TF EDIT and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
MIC
MW AUTO
KL
2 3
Call up the MOVE screen. Point the arrow at +MOVE using the dial or UP/DOWN TF key, and then press the ENT key. P Select the program you want to move. Using the dial or a numeric key, select the program TF number you want to move. Press the ENT key (Pressing the F TUNE key toggles between the uppercase P and the lowercase p).
MO V E F R OM
82 .
MO V E F R OM
P1
145 . 34
69
Select the desired destination program. Using the dial or a numeric key, select the destination F TUNE TF program number. Press the ENT key (Pressing the key toggles between the uppercase P and the lowercase p). To retry the setting, press the
SKIP CLR
MO V E T O
P2 ---- . -----------
key.
The display will return to the PM EDIT screen. Point the arrow at END and then TF press the ENT key (Alternatively, you may press the F key, and then press the TF key with shown on the display). ENT
1
F
MO NI SRC H LAM P
Call up the PMS EDIT screen. Press the F key, and then press SET PMS ED I T the HELP key with shown on CO P Y the display. MO V E The menu will appear. Point the arrow at +PMS using the dial or UP/DOWN key, and TF then press the ENT key. The PMS screen will appear. Point the arrow at +PMS TF EDIT and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
MIC
MW AUTO
KL
2 3
Call up the DEL screen. Point the arrow at +DEL using the dial or UP/DOWN key, TF and then press the ENT key. P
DEL 82 .
Select the program you want to delete. Using the dial or a numeric key, select the program number you want to delete. TF F TUNE Press the ENT key (Pressing the key toggles between the uppercase P and the lowercase p). The display will return to the PMS EDIT screen. Point the arrow at END and TF press the ENT key (Alternatively, you may press the F , and then press the TF key with shown on the display). ENT
70
1 2
F
MO NI SRC H LAM P
Press the key to get the VFO mode. Then, set the frequency on the top line (currently used) band. Select the bank number to which you want to assign a frequency. Press the F key, and then press MRMW the key with shown on SET MR A ---- . ---the display. 1 -------The SET MR screen will appear. Select the bank number using the dial or a numeric key, and then press the DOWN key (Pressing the F TUNE key toggles from the bank groups A through E).
T RX/S ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
ODE
STEP
ATT
HELP
NAME
Select a memory channel. Using the dial or a numeric key, select the channel number to which you want to assign the frequency. Press TF the ENT key.
Give a name to the memory channel. Select each character by turning the dial, and then establish it by pressing the DOWN key. The established character can be canceled by pressing the UP key. Up to 8 characters may be entered for the name.
Store the memory channel. TF After you have finished entering the name, press the ENT key. The frequency will be assigned to the selected memory channel, and then the display will return to the VFO mode.
Note: The settings for the radio, frequency step, attenuator, and CTCSS decoding function, which were completed in the VFO mode, will be stored on the memory channel. In naming the memory channel, you can move 11 characters ahead by turning the dial while holding down the F key.
71
1 2
F
MO NI SRC H LAM P
Press the key to enter the PMS mode. Select a program bank number. The programmed scanning will start. Set the auto memory write function. Press the F key, and then press AUTO MW A U T O MR WR the key with shown on 5 STOP the display. The AUTO MW S T AR T A 9 screen will appear. Point the arrow at START using the UP/DOWN key, and select a program bank using the dial. TF Press the ENT key. The programmed scanning will start and the received frequency will be assigned to the automatically selected memory bank.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
SCN
MIC
4
AUTO
MW
KL
6 9
CRT
PRIO
CTCSS
TF
To stop the auto memory write function, point the arrow at STOP on the AUTO TF MW screen, and then press the ENT key.
Note: The settings for the radio type, frequency step, attenuator, and CTCSS decoding function, which were completed in the PMS mode, will be stored on the memory channel.
MO NI
VOL
PMS
SET
SRC H
MR MW
LAM P
DOWN
UP
VFO A B
WFM A1 84 . 5
SQL
SET MODE
1
STEP
2
ATT
3
HELP
72
Pressing the
SKIP CLR
display , followed by the CLR key (or press only the SKIP key). SKIP will be displayed to indicate the CLR DJ-X2 channel will be skipped during the memory scan. key again will cancel the skip setting.
MIC
4
M NAME
RF C
SKIP
AUTO
MW
KL
6 9
A-B S
SCN
SCRT
7
PRIO
8
CTCSS
TF
SKIP
REC
0
F TUNE
ENT
CLR
MIC
1
F
MO NI SRC H LAM P
Call up the MODE SEL screen. Press the F key, and then press SET MR the HELP key with shown on MODE S E L the display. END The menu will appear. Point the arrow at +MR using the dial or UP/DOWN key, and then TF press the ENT key. The MR screen will appear. Point the arrow at +MODE TF SEL and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
MIC
MW AUTO
KL
Select the radio type you are scanning. Using the dial or UP/DOWN key, point the arrow at the TF MODE SEL radio type you are scanning. Press the ENT key. The ALL radio type can be selected from ALL, AM, NFM, WFM, AM USB, LSB, and CW. If ALL is selected, all the channels will be scanned regardless of the radio type (the initial setting is ALL). The display will return to the MR screen. Point the arrow at END and then press TF TF the ENT key (Alternatively, press the F key, and then press the ENT key with appearing on the display).
73
Call up the MR LINK screen. Press the F key, and then press F SET MO the HELP key with shown on MR NI the display. MR L I NK SRC H MODE S E L The menu will appear. Point the LAM P arrow at +MR using the dial or UP/DOWN key, and then TF press the ENT key. The MR screen will appear. Point the arrow at +MR TF LINK and then press the ENT key.
R POWE
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
STEP
ATT
3
HELP
M NAME
Select the memory bank you want to use for scanning. Using a numeric key, specify the bank number you want F TUNE MR Ba n k L i n k to link. Pressing the key toggles from bank groups A 1---5---A through E. To use all the memory banks for scanning, B ---------select all the banks 0 through 9. After you have finished TF specifying the bank(s), press the ENT key. The display will return to the MR screen. Point the arrow at END and then press TF TF the ENT key (Alternatively you may press the F key, and then press the ENT key with appearing on the display).
1
F
MO NI SRC H LAM P
Call up the PMR screen. Press the F key, and then press SET MR the HELP key with shown on PMR the display. MR L I NK The menu will appear. Point the arrow at +MR using the dial or UP/DOWN key, and then TF press the ENT key. The MR screen will appear. Point the arrow at +PMR TF and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
MIC
AUTO
MW
KL
74
Select the program bank on which you want to set a memory channel for scanning. Using the dial or UP/DOWN key, point the arrow at the TF PMR program you want to set. Press the ENT key. B ANK B ANK 1 Select the program number you want to assign to a memory channel. Using the dial or UP/DOWN key, point the arrow at the TF program number you want to select. Press the ENT key. PMR BANK ----PG PG 1 - - - - -
Select a memory bank. TF Select a memory bank and then press the ENT key. Using the dial or a numeric key, specify a memory bank F TUNE number (Pressing the key toggles from bank groups A through E). Move the arrow back to the position pointing at the channel by pressing the DOWN key.
Select a memory channel. Using the dial or a numeric key, specify a memory TF channel number. Press the ENT key (To cancel the SKIP setting, press the CLR key).
PMR MEMORY A2 84 . 5 1 2 A BC
Repeat the above steps 2 through 5 to register all the channels on which you are TF scanning, and then press the ENT key. The display will return to the PMR BANK screen. Point the arrow at END and TF TF then press the ENT key (Alternatively you may press the F key, and then ENT key with shown on the display).
75
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET MODE
1
STEP
2
ATT
3
HELP
M NAME
RF C
MIC
4
MW AUTO
5
KL
6
A-B S
SCN
SCRT
PRIO
S CTCS
9
TF
Stopping the scanning A~B S Press the SCN key again. The scanning will stop.
1
F
MO NI SRC H LAM P
Call up the MR EDIT screen. Press the F key, and then press SET MR ED I T the HELP key with shown on the COP Y CH display. MOV E CH The menu will appear. Point the arrow at +MR using the dial or UP/DOWN key, and then TF press the ENT key. The MR screen will appear. Point the arrow at +MR TF EDIT and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
MIC
AUTO
MW
KL
Call up the COPY BANK screen. Point the arrow at +COPY BANK using the dial or TF UP/DOWN key, and then press the ENT key.
76
3 4
Select a source memory bank. Using the dial or a numeric key, select the bank number F TUNE TF you want to copy. Press the ENT key (Pressing the key toggles from bank groups A through E). Select a destination memory bank. Using the dial or a numeric key, select the bank number to which you want to copy the source memory bank. TF F TUNE Press the ENT key (Pressing the key toggles from bank groups A through E). To retry the setting, press the
SKIP CLR
COPY BANK A = --
COPY BANK A1 = B2
key.
The display will return to the MR EDIT screen. Point the arrow at END and then TF press the ENT key (Alternatively you may press the F key, and then press the TF key with appearing on the display). ENT
1
F
MO NI SRC H LAM P
Call up the MR EDIT menu. Press the F key, and then press SET the HELP key with shown on MR ED I T COP Y CH the display. MOV E CH The menu will appear. Point the arrow at +MR using the dial or UP/DOWN key, and then TF press the ENT key. The MR screen will appear. Point the arrow at +MR TF EDIT and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
MIC
MW AUTO
KL
Call up the COPY CH screen. Point the arrow at +COPY CH using the dial or UP/DOWN key, and then press TF the ENT key.
77
Select the bank that includes the memory channel to be copied. Select the bank number using the dial or a numeric key F TUNE (Pressing the key toggles from bank groups A C O P Y F R OM A2 ---- . ---through E). Move the arrow to the position pointing at the -------channel by pressing the DOWN key.
Select the memory channel you are copying. Using the dial or a numeric key, select the channel TF number you are copying. Press the ENT key.
C O P Y F R OM
A2 12
84 . 5 A BC
Select the bank that includes the destination memory channel. Using the dial or a numeric key, select the bank number F TUNE (Pressing the key toggles from bank groups A COPY TO B3 ---- . ---through E). Move the arrow to the position pointing at the -------channel by pressing the DOWN key.
Select the destination memory channel. Select the destination channel number using the dial or a TF numeric key, and then press the ENT key. To retry the setting, press the
SKIP CLR
COPY TO
key.
The display will return to the MR EDIT screen. Point the arrow at END and then TF press the ENT key (Alternatively you may press the F key, and then press the TF key with appearing on the display). ENT
1
F
MO NI SRC H LAM P
Call up the MR EDIT screen. Press the F key, and then press SET the HELP key with shown on MR ED I T COP Y CH the display. MOV E CH The menu will appear. Point the arrow at +MR using the dial or UP/DOWN key, and then TF press the ENT key. The MR screen will appear. Point the arrow at +MR TF EDIT and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
MIC
MW AUTO
KL
78
Call up the MOVE BANK screen. Point the arrow at +MOVE BANK using the dial or TF UP/DOWN key, and then press the ENT key.
2 3
MR ED I T MO V E B ANK DE L B ANK
Select the memory bank you want to move. Using the dial or a numeric key, select the memory bank TF you want to move. Press the ENT key (Pressing the F TUNE key toggles from bank groups A through E).
MOVE BANK A1 --
Select the destination memory bank. Select the destination bank number using the dial or a TF numeric key, and then press the ENT key (Pressing the F TUNE key toggles from bank groups A through E). To retry the setting, press the
SKIP CLR
MOVE BANK A1 B2
key.
The display will return to the MR EDIT screen. Point the arrow at END and then TF press the ENT key (Alternatively you may press the F key, and then press the TF key with appearing on the display). ENT
1
F
MO NI SRC H LAM P
Call up the MR EDIT menu. Press the F key, and then press SET the HELP key with shown on MR ED I T COP Y CH the display. MOV E CH The menu will appear. Point the arrow at +MR using the dial or UP/DOWN key, and then TF press the ENT key. The MR screen will appear. Point the arrow at +MR TF EDIT and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
MIC
MW AUTO
KL
79
Call up the MOVE CH screen. Point the arrow at +MOVE CH using the dial or UP/DOWN key, and then press TF the ENT key.
Select the bank that includes the memory channel you want to move. Select the bank number using the dial or a numeric key F TUNE MO V E F R OM (Pressing the key toggles from bank groups A A2 ---- . ---through E). Move the arrow to the position pointing at the -------channel by pressing the DOWN key.
Select the memory channel you want to move. Using the dial or a numeric key, select the channel TF number you want to move. Press the ENT key.
MO V E F R OM
A2 12
84 . 5 A BC
Select the bank that includes the destination memory channel. Select the bank number using the dial or a numeric key F TUNE (Pressing the key toggles from bank groups A MO V E T O B3 ---- . ---through E). Move the arrow to the position pointing at the -------channel by pressing the DOWN key.
Select the destination memory channel. Select the destination channel number using the dial or a TF numeric key, and then press the ENT key. To retry the setting, press the
SKIP CLR
MO V E T O
key.
The display will return to the MR EDIT screen. Point the arrow at END and then TF press the ENT key (Alternatively you may press the F key, and then press the TF key with appearing on the display). ENT
80
1
F
MO NI SRC H LAM P
Call up the MR EDIT screen. Press the F key, and then press SET MR ED I T the HELP key with shown on COP Y CH the display. MOV E CH The menu will appear. Point the arrow at +MR using the dial or UP/DOWN key, and then TF press the ENT key. The MR screen will appear. Point the arrow at +MR TF EDIT and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
MIC
AUTO
MW
KL
2 3
Call up the DEL BANK screen. Point the arrow at +DEL BANK using the dial or UP/DOWN key, and then press TF the ENT key.
Using the dial or a numeric key, select the bank number you want to delete. Press the
F TUNE
DELETE BANK A3
The display will return to the MR EDIT screen. Point the arrow at END and then TF press the ENT key (Alternatively you may press the F key, and then press the TF key with appearing on the display). ENT
81
1
F
MO NI SRC H LAM P
Call up the MR EDIT screen. Press the F key, and then press SET the HELP key with shown on MR ED I T COP Y CH the display. MOV E CH The menu will appear. Point the arrow at +MR using the dial or UP/DOWN key, and then TF press the ENT key. The MR screen will appear. Point the arrow at +MR TF EDIT and then press the ENT key.
ER POW
VOL
PMS
SET
SQL
DOWN
UP
VFO A B
MR MW
SET
MODE
1
STEP
2
ATT
3
HELP RF C
M NAME A-B S
MIC
MW AUTO
KL
Call up the DEL CH screen. Point the arrow at +DEL CH using the dial or UP/DOWN key, and then press the TF ENT key. Select the bank that includes the memory channel you want to delete. Select the bank number using the dial or a numeric key F TUNE (Pressing the key toggles from bank groups A DEL through E). Move the arrow to the position pointing at the A2 ---- . ----------channel by pressing the DOWN key.
2 3
Select the memory channel you want to delete. Using the dial or a numeric key, select the channel you TF want to delete. Press the ENT key (Pressing the F TUNE key toggles from bank groups A through E). To retry the setting, press the
SKIP CLR
DEL A2 84 . 5 1 2 A BC
key.
The display will return to the MR EDIT screen. Point the arrow at END and then TF press the ENT key (Alternatively you may press the F key, and then press the TF key with appearing on the display). ENT Restoring the deleted memory channel The memory channel you have deleted can be restored. As in the above steps, TF call up the channel number you have deleted, and then press the ENT key. The previously stored channel will be restored.
Note: If any other frequency is already assigned to the once deleted channel, the previous channel data cannot be restored.
82
1
F
MO NI SRC H LAM P
Call up the MR NAME SRC screen. Press the F key, and then press M NAME the RFC key with appearing on the display.
ER POW
VOL
PMS
SET
SQL
MR N A M E S R C A BCDE FGH I J K
DOWN
UP
VFO A B
MR MW
SET MODE
1
STEP
2
ATT
3
HELP
M NAME
RF C
MIC
MW AUTO
KL
A-B S
Enter the characters you want to search for. Select each character by turning the dial, and then MR N A M E S R C establish it by pressing the DOWN key. The established A BCDE FGH I J K character can be canceled by pressing the UP key. Even A BC if you enter the first few characters, the appropriate channel can be searched for. At least 1 character should be entered.
Start the search. TF Press the ENT key. The search will start. After the search has been finished, the appropriate channel appears on the display. If more than 1 channel are found, appears on the right end of the display indicating that more than 1 channel have been found. Select a channel. Using the dial or UP/DOWN key, select the channel you want to receive. Press TF the ENT key.
Note: If many memory channels are stored, it will take longer time for the search.
83
4. Appendix
4.1 Specifications
Range of received frequencies Received radio type 0.1MHz2149.999950MHz WFM, NFM, AM, USB, LSB, CW AUTO STEP, 50Hz, 100Hz, 200Hz, 500Hz, 1kHz, 2kHz, 5kHz, 6.25kHz, 8.33kHz, 9kHz, 10kHz, 12.5kHz, 15kHz, 20kHz, 25kHz, 30kHz, 50kHz, 100kHz, 125kHz, 150kHz, 200kHz, 250kHz, 500kHz, USER STEP (optional) (Only the digits of 1 MHz, 10 MHz, and 100 MHz can be changed.) 0.1MHz5MHz Receiving sensitivity Excluding the frequency band 5MHz900MHz for electric communication business use The typical sensitivity values are shown here. 900MHz2150MHz Memory channel Search path memory Priority channel Memory banks 1-bank channel Band search Antenna connector Power source AM 1.5V (10dBS/N) SSB/CW 0.6V (10dBS/N) AM SSB/CW NFM WFM SSB/CW NFM WFM 1.0V (10dBS/N) 0.5V (10dBS/N) 0.5V (12dBSINAD) 2.0V (12dBSINAD when stereo signal are received) 1V (10dBS/N) 2V (12dBSINAD) 4V (12dBSINAD)
Frequency steps
2,000 channel 1,000channel 1channel (freely selectable from 2,000 channels) 50 40 20 BNC,50 4.8V DC (Ni-Cd), 7.2V DC (Ni-Cd), 6V DC (AA battery)
External power source 1016VDC Rated output min.100 mW, 10% THD At rated output: Approx. 150 mA (when 6 V power source is used) Current consumption At standby: Approx. 100 mA In BS mode: Approx. 50 mA Weight Approx. 200 g E x t e r n a l d i m e n s i o n s 5715027.5mm Operating temperature 1450F Note: The North American version cannot be used to receive any frequency for cellular phones.
84
4.2 Troubleshooting
Trouble Cause The volume level is too low. No sound is heard from the speaker. The squelch level is too high. Remedial action Press the VOL key on the left side of the DJ-X2000, and then turn up the volume (see page 20). Press the SQL key on the left side of the DJ-X2000, press the DOWN key to decrease the level until any noise can be heard, and then increase the level until the noise is no longer heard (see page 21). Properly attach the antenna (see page 13). Cancel the key locking function (see page 28). When appears on the display,
No signal received.
can
be
is
not
The settings for frequencies, etc. cannot be performed. The warning beep is emitted or the sound is distorted. The display turns OFF.
The key locking function is active. The battery has run out.
85
Keys
Menu [SET] [POWER] [DIAL] [VOL] [SQL] [F] [MONI] [F]&[MONI] [LAMP] [SRCH] [F]&[SRCH] [VFO] [A=B] [MR] [MW] [PMS] [ENT] [CLR] Function involved Operational explanation available Menu [SCN] [RF C] [.] [MODE] [STEP] [ATT] [MIC] [AUTO MW] [KL] [M NAME] [SCRT] [PRIO] [CTCSS] [AB S] [SKIP] [REC] [F TUNE] [TF] Function involved Operational explanation available
86
Functions
Menu Submenu Inst COPY A=B COPY MR. CH COPY PMS Inst COPY CH DEL CH COPY BANK DEL BANK MR LINK MODE SEL SCAN SKIP SET CTCSS M. TUNE Inst SCAN PASS COPY DEL PMS LINK AUTO MR WR VFO MR ABS MODE SCAN PMR SCAN VFO LINK S_LEVEL CTCSS SCAN SCAN SETUP SCAN MODE SCAN MODE BUSY Timer RX Timer SINGLE INTERVAL CONTINUE SET Function involved Operational explanation available
VFO
MR
PMS
SCAN
CH SCOPE
87
Menu
Function involved
LAMP
TIMER BEEP TONE STEREO BELL BATT SAVE BATT VOLT LANGUAGE DIRECT WR MESSAGE CLONE Inst TX CLONE RX CLONE MANUAL REVERSE SET SYSTEM ALL A/B SQ SET FLASH TUNE RF CHECK SPECIAL REC TRANCEIVER CHECKER CallWait RX AF MIC SET Japanese English SET
CTCSS SET
RESET
88