Separating Acids and Neutral Compounds by Solvent Extraction 705
Separating Acids and Neutral Compounds by Solvent Extraction 705
Separating Acids and Neutral Compounds by Solvent Extraction 705
by Solvent Extraction
PURPOSE OF THE EXPERIMENT
Use solvent extraction techniques to separate a mixture consisting of a carboxylic acid and a
neutral compound.
BACKGROUND REQUIRED
You should be familiar with the experimental techniques used to determine melting points, to
test for acidity using pH paper, and to separate a solid from a solution using vacuum filtration.
BACKGROUND INFORMATION
Frequently, organic chemists must separate an organic compound from a mixture of compounds,
often derived from natural sources or as products of synthetic reactions. One technique used to
separate the mixture compounds is called extraction. Extraction is a process that selectively
dissolves one or more of the mixture compounds into an appropriate solvent. The solution of
these dissolved compounds is often referred to as the extract.
Extraction processes include removal of soluble compounds from a solid matrix, such as occurs
in brewing coffee or tea, or in decaffeinating coffee with liquid carbon dioxide. In the organic
chemistry laboratory, however, extraction almost always refers to the transfer of compounds
from one liquid solvent to another liquid solvent.
A compound can be separated from impurities in a solution by extracting the compound from
the original or first solvent into a second solvent. The compound must be more soluble in the
second solvent than in the first solvent, and the impurities must be insoluble in the second
solvent.
Also, to effect the extraction, the two solvents selected
must be immiscible, or not soluble in one another, so
that they produce two separate solvent layers. After
dissolving the mixture in the first solvent, the solution
is added to the second solvent. The two layers are
vigorously mixed to maximize the surface area between
them. This mixing facilitates the transfer of a dissolved
compound from one layer to another. Once the transfer
process is complete, the layers are again allowed to
form, as shown in Figure 1. Separation of the two
layers then completes the separation of the desired
compound from the impurities.
Choosing a solvent
However, dichloromethane is more dense than water. When dichloromethane is used as the
nonpolar solvent, the water layer will be the top layer, as shown in Figure 5.
Although the identity of each layer can be established from the density of each solvent, their
identities should be confirmed. To confirm the identities of the layers, one or two drops of water
are introduced just below the surface of the top layer. If the drops of water mix with the top
layer, then the top layer is the water layer. If the drops of water fall through the top layer to the
layer below, then the water layer is the bottom one. It is a good practice to save all layers in
labeled containers until the experiment is complete and the desired product is isolated.
Often the two solvents will not completely separate after shaking, due to the formation of an
emulsion at the interface between them. An emulsion is a suspension of small droplets of one
liquid in another liquid. (A familiar example of an emulsion is oil and vinegar, after shaking).
Emulsions are generally opaque or cloudy in appearance and are often mistaken as a third layer.
The small size of the droplets in an emulsion causes the separation of the two solvents to take
place very slowly. Several procedures may be helpful to facilitate this separation. For example,
gentle swirling of the container, addition of a few drops of saturated aqueous sodium chloride
(NaCl) or ethanol, or addition of more solvent to dilute the solutions may help. In particularly
difficult cases, it may be necessary to filter the mixture to remove small solid particles that
promote emulsion formation.
A simple, but useful, guide to solubility is like dissolves like. That is, nonpolar compounds,
including most organic compounds, are more soluble in nonpolar solvents than in polar
solvents. On the other hand, ionic and polar compounds are more soluble in polar solvents, such
as water. These solubility differences can be exploited to separate nonpolar compounds from
ionic or polar compounds.
For example, synthetic reactions often produce ionic, inorganic salts as by-products of the
desired nonpolar organic product. In such cases, these salts are removed by washing the
nonpolar solvent with water. The organic compound remains dissolved in the nonpolar solvent.
Some organic compounds are sufficiently polar to be quite soluble in water. Extraction of such
polar compounds into a nonpolar solvent is often difficult. The process can be facilitated by
using the technique called salting out. Inorganic salts, such as NaCl, are dissolved in water to
reduce the solubility of the organic compound in the aqueous layer. Under these conditions, the
organic compound preferentially dissolves in the nonpolar layer.
We will separate a mixture of acetanilide (a weak base) from p-toluic acid (a weak acid). These
two compounds have similar polarities (and therefore have similar solubility properties); they
are essentially insoluble in highly polar solvents such as water, but very soluble in solvents with
moderate polarity such as ethers or ketones. So, if placed into a separatory funnel with both an
organic solvent and water, both compounds will dissolve in the organic layer.
In order to separate these compounds, we will convert the water insoluble acid into a water
soluble salt:
O OH - +
O O Na
+
Na OH + H2O
CH3
CH3
Because an ionic compound is formed in this reaction, the product is very soluble in water, but
not soluble in ether. So this product (called sodium p-toluate) will extract into the aqueous
layer.
The other compound, acetanilide, does not react with NaOH and remains dissolved in the
relatively nonpolar ether. The separatory funnel can be used to separate the aqueous layer
(containing the sodium p-toluate) from the organic layer (containing the acetanilide). This is
how the compounds are separated; the remainder of the experiment consists of recovering the
two compounds in their pure (solid) form.
To recover acetanilide, you will dry the nonpolar layer with anhydrous sodium sulfate (Na2SO4)
and evaporate the solvent under vacuum. As the solvent evaporates, the acetanilide will remain.
To recrystallize the p-toluic acid from the aqueous layer, we simply have to reverse the reaction
above. By adding some strong acid to the aqueous layer, the NaOH is neutralized, and the ionic
salt is converted back into p-toluic acid. (Note that this is simply the reverse of the reaction
shown above – the salt is converted back into the acid, forming NaCl as a by-product). Because
p-toluic acid is NOT very water soluble, it will crystallize from the water as it is formed.
After you dry the compounds, you will measure the mass of each isolated compound. Finally,
you will measure the melting point of the acetanilide and assess its purity by comparing the
experimentally measured melting point with the literature value.
Figure 7: A flowchart summarizing the steps of extraction for this experiment
PROCEDURE
Preview
PROCEDURE
Chemical Alert
acetanilide—toxic and irritant
anhydrous sodium sulfate—irritant and hygroscopic
diethyl ether—flammable and irritant
3M hydrochloric acid—toxic and corrosive
0.5M sodium hydroxide—toxic
Caution: Wear departmentally approved safety goggles at all times while in the chemistry
laboratory.
NOTE 1: Be sure to close the stopcock at the bottom of the separatory funnel before adding
solutions.
Caution: Acetanilide is toxic and irritating. Diethyl ether is flammable and irritating.
Keep away from flames or other heat sources. Prevent eye, skin, and clothing contact
with these compounds. Avoid inhaling vapors or dust or ingesting these compounds.
Weigh 0.25—0.35 g of acetanilide and 0.4—0.6 g p-toluic acid. Record the exact mass of each
compound. Place 25 mL of diethyl ether into a 100-mL beaker. Add the two solids to the diethyl
ether and mix to dissolve. Pour this solution into a 125-mL separatory funnel supported by an
iron ring, as shown in Figure 3.
NOTE 2: the solids may take 5 minutes or more to dissolve. You should stir the mixture during
this time. Because agitation (by stirring) greatly increases the evaporation rate of the ether, this
step should be performed in the hood, or you can perform this step at your desk if you keep the
beaker covered with a watch glass. This will minimize the ether fumes in the lab.
2. Extracting p-Toluic Acid
NOTE 3: If you open the stopcock while the glass stopper is in the top of the separatory funnel,
a slight vacuum will be created, and the bottom layer will not drain from the funnel.
Remove the glass stopper from the top of the funnel, and open the stopcock to allow the aqueous
layer to drain into a clean, labeled 100-mL beaker. [NOTE 2] When the interface between the
layers just reaches the bottom of the funnel (top of the stopcock), close the stopcock to retain
the ether layer in the funnel.
Add a second 10-mL NaOH portion to the funnel to remove any p-toluic acid remaining in the
ether layer. Mix with frequent venting. After the layers have separated, drain the aqueous layer
into the beaker with the first extract. Repeat with a third 10-mL NaOH portion.
Add 5 mL of distilled or deionized water to the separatory funnel and mix. Drain the water layer
into the beaker containing the three NaOH solution extracts.
Caution: 3M Hydrochloric acid (HCl) is toxic and corrosive. Prevent eye, skin, and clothing
contact. Avoid inhaling the vapors or ingesting HCl.
To precipitate the p-toluic acid, carefully add 3M HCl to the NaOH solution extracted in part 2.
As soon as the solution becomes acidic, a precipitate of p-toluic acid will begin to form. (The
water soluble salt is converted to a water insoluble acid in an acidic solution). You should be
able to calculate how many mL of 3.0 M HCl is required to neutralize the 30. mL of
0.5 M NaOH that you added.
To test for acidity, remove a drop of the solution with a stirring rod and place the drop on a
small piece of pH test paper. Continue to add the 3M HCl, dropwise with stirring, until no more
solid is produced and the solution tests moderately acidic (approximately pH 3).
Weigh a filter paper and record its mass. Using the weighed filter paper, separate the crystals
from the solution using vacuum filtration with a Büchner funnel. Support the crystals and paper
on a watch glass and allow the crystals to air dry.
4. Isolating Acetanilide
Caution: Anhydrous sodium sulfate (Na2SO4) is irritating and hygroscopic. Prevent eye,
skin, and clothing contact.
Select the separatory funnel containing the ether layer from Part 2. Drain the ether solution into
a small Erlenmeyer flask and add approximately 1 g of anhydrous Na2SO4 to the flask to remove
any traces of water from the solution. (If the solvent contains water, it will not evaporate
completely in the next step). Stopper the flask and allow it to stand for 5 min with occasional
swirling. (NOTE 3).
NOTE 4: After anhydrous Na2SO4 absorbs water, it will look like salt or sugar.
Decant the ether/acetanilide solution from the Erlenmeyer flask into a clean, dry, pre-weighed
round-bottom flask. To remove the ether solvent and recover the acetanilide crystals, we will
take advantage of the fact that a solvent’s boiling point decreases as the atmospheric pressure
decreases. By lowering the pressure above the solution, we can boil the ether away at room
temperature, or by warming it slightly. (This is MUCH SAFER than applying heat, because
ether is extremely flammable, and has a low flash point!).
Under the supervision of your lab instructor or T.A., connect the round-bottom flask to the
Roto-Vap and apply vacuum. Lower the round-bottom into the warm water bath and turn on the
motor to begin rotating the flask. The ether will begin boiling within a minute; all of the ether
should evaporate within about 3 - 5 minutes. After all of the liquid is gone and the crystals
appear dry, continue heating the sample for an additional minute to ensure complete evaporation
of the ether.
NOTE 5: If possible, the sample of p-toluic acid should be dried in an oven for 10 minutes to
completely evaporate the water. Consult your instructor to find out how you should dry your
p-toluic acid sample.
When all of the samples are dry measure the mass of each compound. Measure the melting
point of each compound, and assess its purity by comparing the measured melting point with the
literature value.
NOTE 6: Your thermometer may only record temperatures up to 150° C; if this is the case, you
will not be able to record the m.p. of p-toluic acid, which has a literature m.p. value of
180° - 181°C!
6. Cleaning Up
Use the waste collection containers, provided by your laboratory instructor. If you used the
vacuum method to remove the ether from the acetanilide (step 4a), then the ether from your trap
should be disposed of in the organic solvent waste container. There will be a separate container
for the solids. The aqueous layer (from which the p-toluic acid was recovered, in part 3) can be
disposed of in the sink, diluting with a large amount of running water. Clean your glassware
with soap or detergent.
Caution: Wash your hands thoroughly with soap or detergent before leaving the laboratory!
(You always do that anyway, don’t you?)
POST-LABORATORY QUESTIONS
1. Based on the amounts of p-toluic acid and acetanilide you recovered, estimate the
composition of the original mixture.
2. What product would you obtain if you evaporated the water from the NaOH layer prior to
acidifying the layer?
3. Suppose that you used dichloromethane instead of diethyl ether as the nonpolar solvent in
this experiment. What changes in the procedure would you make in view of the fact that
dichloromethane is more dense than water?
4. Benzoic acid (C6H5—COOH) is a weak acid and naphthalene is neutral, neither acidic or
basic. Prepare a flowchart for the separation and recovery of benzoic acid and
naphthalene.
O OH
5. After comparing the melting points of each of your compounds to their respective
literature values, comment on the purity of each compound.
Pre-Laboratory Assignment Solvent Extraction
1. Briefly describe the hazards you should be aware of when you work with:
(b) 3M HCl
(a) How would you determine which layer is the aqueous layer after you add NaOH solution to
the ether solution of your compounds?
(c) What visible evidence(s) of reaction will you see when you acidify the NaOH extract with
HCl solution?
(d) In which layer would p-toluic acid be more soluble if p-toluic acid were added to a two-layer
mixture of diethyl ether and water?
Solvent Extraction, Pre-lab page 2
(e) How would the results differ if you added sodium p-toluate instead of p-toluic acid to the
two-layer mixture of diethyl ether and water?
4. How many milliliters of 3.0 M HCl would be required to neutralize 30. mL of 0.50 M
NaOH? (Show your work).
5. Briefly explain how you will isolate p-toluic acid after it is extracted it into NaOH solution.
6. Write the equation for the chemical reaction of the toluate ion that will occur when you
add HCl solution to the NaOH extract in part 3.