Huawei Cisco Xref Switch CLI PDF

HUAWEI Switch CLI
contrast with
CISCO
www.huawei.com
Copyright 2013 Huawei Technologies Co., Ltd. All rights reserved.

Huawei Enterprise USA, Inc. proprietary. Available for use by authorized partners.
Huawei Enterprise USA, Inc. proprietary. Provided for use by authorized partners or by NDA.
Objectives
Upon completion of this course, you will be able to:
Understand the characteristic of Huawei CLI
Be familiar with some common Huawei commands
Configure some basic Huawei Switch features
Page1
Agenda
1
Abstract
Huawei and Cisco command-view contrast
Switch Features configuration contrast
Page2
Abstract
The overall mechanism of Huawei and Cisco CLI are similar.
The styles of Huawei and Cisco CLI are identical.
Huawei CLI has corresponding relationship with Cisco's in

particular command.
After learning these sameness and differences between

Huawei and Cisco CLI, you can skillfully practice Huawei
CLI in short time if you learnt well the Cisco CLI.
Page3
Agenda
1
Abstract
Command style contrast
Common commands contrast
Page4
Huawei configuration views and Cisco configuration modes contrast
Huawei configuration views and Cisco configuration modes are quite similar
Cisco:
User mode, use > as prompt, e.g. Cisco>
Privileged mode, use # as prompt, e.g. Cisco#
Configuration mode, use # as prompt, e.g. Cisco(config)#
Other configuration mode, use # as prompt, e.g. Cisco(config-XX)#
Huawei:
User view, use < > as prompte.g. <Huawei>
System view, use [ ] as prompt, e.g. [Huawei]
Other configuration view, use [ ] as prompt, e.g. [Huawei-XX]
You can see that Huawei never have the single configuration mode like Cisco
the system view of Huawei is equivalent to privileged mode plus configuration
mode of Cisco.
Page5
Command structure contrast
Huawei and Cisco have similar command structure
Cisco>show running-configuration
prompt
command
space
Keyword, parameter
Huawei>display current-configuration
Page6
Common shortcut keys contrast
The same to use up cursor key and down cursor key to show the
history commands
The same to use ? to help to find the following command/parameter
The same to use Tab key to full fill the command
The same to use Backspace key to Deletes a character before the cursor
Huawei supports to defining hotkeys, and you can use the command display
hotkey to show the hotkeys in use
Page7
Agenda
1
Abstract
Common commands contrast
Page8
Common command contrast
Command keywords contrast
Most part of Huawei command keywords has the fixed contrast to Cisco, know
about these will help you to learn Huawei command quickly if you have a good
skill on Cisco.
Common command keywords contrast:
show <- -> display
no <- -> undo
exit <- -> quit
clear <- -> reset
debug <- -> debugging
neighbor <- -> peer
detail <- -> verbose
delete <- -> delete
match <- ->if-match
Page9
Configure host name
Cisco(config)# hostname <hostname>
[huawei] sysname <sysname>
Display information about version
Cisco# show version
[huawei] display version
Display information about configuration
Cisco# show running-configuration
[huawei] display current-configuration
Display information about configuration
Cisco# show interface [ interface-type [ interface-number ] ]
[huawei] display interface [ interface-type [ interface-number ] ]
Huawei command display this is a convenient command to show the configuration in the
current view
Page10

Huawei command
Cisco command
Press Enter key into the user view
Enter the privileged mode
<Quidway>
Cisco> enable
Cisco#
Enter the system view

<Quidway> system-view
[Quidway]
Enter interface view

[Quidway] interface interface-mode
[Quidway-interface-mode]
Enter router view

[Quidway] ospf 1
[Quidway-ospf-1]
Enter AAA view

[Quidway] aaa
[Quidway-aaa]
Enter configuration mode

Cisco# configure terminal
Cisco (config)#
Enter interface-configuration mode

Cisco (config)# interface interface-mode
Cisco (config-if)#
Enter router-configuration mode

Cisco (config)# router ospf 1
Cisco (config-router)#
Enter AAA-configuration mode

Cisco (config)# aaa new-model
Page11
Agenda
1
Abstract

1
Basic Configuration
Ethernet Configuration
Reliability
QoS
Security
Device Management
Network Management
Page12
Configuring the local user

Huawei command
Cisco command
Enter the configuration mode
Enter the AAA view
Create a local user and set the password
[Quidway] aaa
Cisco (config)# username Huawei password 123456
Create a local user and set the password
Specify the local users level
[Quidway-aaa] local-user Huawei password simple 123456
Cisco (config)# username Huawei privilege 3
Specify the local users level

[Quidway-aaa] local-user Huawei level 3
Specify the local users service-type

[Quidway-aaa] local-user Huawei service-type telnet
Page13
Login by console
When login through console port ,please use the following parameter
Parameter
Value
Bit per second (Baud rate)
9600
Data bits
Parity check
None
Stop bits
Flow control
None
Page14
Login by Telnet
Huawei command
Cisco command
Configure VTY user interfaces
Configure VTY user interfaces
[Quidway] user-interface vty 0 4
Cisco (config)# line 0
Set the authentication mode
Set the authentication mode
[Quidway-ui-vty0-4] authentication-mode {none | password | aaa }
Cisco (config-line)# no login | login { <cr> | local | tacacs }
If you use the authentication-mode as password, you

need to set the password
If you use the authentication-mode as login, you need

to set the password
[Quidway-ui-vty0-4] set authentication password { cipher | simple }

password
Cisco (config-line)# password password
Set the VTY user level

[Quidway-ui-vty0-4] user privilege level 3
Set the VTY user level

Cisco (config-line)# privilege level 3
Page15
Login by SSH
IP Network
SSH Client
SSH Server
Pre-conditions:
SSH client login the SSH server with the password mode
IP routing is normal between SSH client and SSH Server
Huawei command
Cisco command
Configure the SSH user and the password of the user
Configure the local user and the password of the user
[Quidway] aaa

[Quidway-aaa] local-user Huawei service-type ssh

[Quidway-aaa] quit
Page16
Login by SSH
Generate a local key pair on the server
Generate a local key pair on the server
[Quidway] rsa local-key-pair create

The key name will be: Quidway_Host The range of public key size is
(512 ~ 2048).
NOTES: If the key modulus is greater than 512, I
t will take a few minutes.
Input the bits in the modulus [default = 512]: 1024
Generating
keys..........++++++++++++..........++++++++++++.................................
..++++++++......++++++++
Cisco(config)# ip domain-name test

Cisco(config)# crypto key generate rsa
The name for the keys will be: Cisco.test
Choose the size of the key modulus in the range of 360 to 2048 for
your General Purpose Keys. Choosing a key modulus greater than
512 may take a few minutes.
How many bits in the modulus [512]: 1024
% Generating 1024 bit RSA keys, keys will be non-exportable...[OK]
Enable the STelnet service on the SSH server

[Quidway] stelnet server enable
[Quidway] ssh user Huawei authentication-type password
Configure authentication-mode of the VTY as SSH

Cisco (config)# line 0 4
Cisco (config-line)# login local
Cisco (config-line)# transport input ssh
Configure authentication-mode of the VTY as SSH

[Quidway-ui-vty0-4] authentication-mode aaa
[Quidway-ui-vty0-4] protocol inbound ssh
Page17
Software Upgrade by FTP

Huawei command
Cisco command
Login the FTP Server, then enter the username

and the password on the FTP Server
Login the FTP Server and get the new system software
from the FTP Server
<Quidway> ftp 192.168.161.141
Cisco# copy ftp://huawei:8031@192.168.161.141/S9999.bin

Bootflash:S9300.bin
Trying ftp 192.168.161.141

Press CTRL+K to abort
Configure the new system software as the next startup
Connected to ftp 192.168.161.141

220 FTP service ready.
User (192.168.161.141:(none)):huawei
331 Password required for huawei
Cisco(config)# boot system flash:S9300.bin

Cisco(config)# end
Reboot the device
Password: 8031
Get the new system software from the FTP Server
Cisco# reload
[ftp] get S9999.cc S9300.cc

<Quidway> startup system-software S9300.cc
Reboot the device

<Quidway> reboot
Page18
Software Upgrade by TFTP

Huawei command
Cisco command
Login the TFTP Server and get the new system

software from the TFTP Server
Login the TFTP Server and get the new system

software from the TFTP Server
<Quidway> tftp 192.168.161.141 get S9300.cc
Cisco# copy tftp://192.168.161.141/S9300.bin bootflash:
<Quidway> startup system-software S9300.cc
Cisco(config)# boot system flash:S9300.bin

Cisco(config)# end
Reboot the device

<Quidway> reboot
Reboot the device

Cisco# reload
Page19
NTP Function
NTP Server
NTP Client
172.16.1.1/16
NTP
Switch A
Switch B
Pre-conditions:
The operating mode of NTP is client/server mode

IP routing between Switch A and Switch B is normal
Page20
NTP Function
Switch A (Server):
Huawei command
Cisco command
Configure Switch A as the NTP Server and Specify the

stratum of the NTP master clock
Configure Switch A as the NTP Server and Specify the

stratum of the NTP master clock
<Quidway_A> system-view
[Quidway_A] ntp-service refclock-master 2
Cisco_A# configure terminal

Cisco_A(config)# ntp master 2
Switch B (Client):
Specify the IP address of the remote NTP server
Specify the IP address of the remote NTP server
<Quidway_B> system-view
[Quidway_B] ntp-service unicast-server 172.16.1.1
Cisco_B# configure terminal

Cisco_B(config)# ntp server 172.16.1.1
Page21
Agenda
1
Abstract

1
Basic Configuration
Reliability
QoS
Security
Device Management
Network Management
Page22
Auto-negotiation of the
Interfaces
Huawei command
Cisco command
Configure the port as the auto negotiation mode, by

default, an interface works in auto negotiation mode
Configure the port as the auto negotiation mode, by

default, an interface works in auto negotiation mode
[Quidway] interface GigabitEthernet1/0/1

[Quidway-GigabitEthernet1/0/1] negotiation auto
Cisco(config)# interface Gigabitethernet1/0/1

Cisco(config-if)# no speed
You can set the speed on an electrical interface work

in auto-negotiation mode
You can set the speed on an electrical interface work

in auto-negotiation mode
[Quidway-GigabitEthernet1/0/1] auto speed { 10 | 100 | 1000 }*
Cisco(config-if)# speed auto { 10 | 100 | 1000 }*
You can set the duplex mode on an electrical interface

worked in auto negotiation mode

worked in auto negotiation mode
[Quidway-GigabitEthernet1/0/1] auto duplex { full | half } *
Cisco(config-if)# duplex auto
Page23
Forcible Setting the Rate and

Duplex Mode
Huawei command
Cisco command
Set the interface to work in non-automatic negotiation

mode
Set the interface to work in non-automatic negotiation

mode

[Quidway-GigabitEthernet1/0/1] undo negotiation auto
Cisco(config)# interface GigabitEthernet1/0/1

Cisco(config-if)# speed nonegotiate
You can set the speed on an electrical interface

worked in non-automatic negotiation mode
You can set the speed on an electrical interface

Cisco(config-if)# speed { 10 | 100 | 1000 }
[Quidway-GigabitEthernet1/0/1] speed { 10 | 100 | 1000 }

You can set the duplex on an electrical interface

Cisco(config-if)# duplex { full | half }
[Quidway-GigabitEthernet1/0/1] duplex { full | half }
Page24
Jumbo frame function

Huawei command
Cisco command
Under the port view, set the maximum length of the

frames that can pass through the interface
Set the maximum length of the frames that can pass

through the interface

[Quidway-GigabitEthernet1/0/1] jumbo enable value
Cisco(config)# system mtu jumbo value
Page25
Power over Ethernet function

Huawei command
Cisco command
Enable the POE function on the interface, by default,

the POE function is auto-enable on the interface
Enable the POE function on the interface, by default,

the POE function is auto-enable on the interface
[Quidway] interface Ethernet0/0/1
[Quidway-Ethernet0/0/1] poe enable

Cisco(config)# interface fastEthernet0/0/1
Cisco(config-if)# power inline auto
(Optional) Configure the maximum output power of the

interface
(Optional) Configure the maximum output power of the

interface
[Quidway-Ethernet0/0/1] poe max-power power_values

[Quidway-Ethernet0/0/1] quit
Cisco(config-if)# power inline [auto | static] max power_values
(Optional) Configure the POE mode as manual

(Optional) Configure the POE mode as manual and
supply the power over the interface by manual
Cisco(config-if)# power inline static
[Quidway] poe power-management manual

[Quidway] poe power-on interface Ethernet0/0/1
Page26
Static LACP Link Aggregation

Group
GE1/0/1
Switch A
GE1/0/8
Switch B
Huawei command
Cisco command
Create a channel group
Create a channel group
[Quidway] interface Eth-Trunk 1
Cisco(config)# interface port-channel 1

Cisco(config-if)# switchport
Cisco(config-if)# exit
Page27
Static LACP Link Aggregation

Group
Configuring the Channel group Load Balancing
Configuring the Channel group Load Balancing
[Quidway-Eth-Trunk1] load-balance method
Cisco(config)# port-channel load-balance method
Specify the channel group mode as LACP
Assign the port to the channel group, and specify the

port as LACP mode
[Quidway-Eth-Trunk1] mode lacp-static

[Quidway-Eth-Trunk1] bpdu enable
[Quidway-Eth-Trunk1] quit

Cisco(config-if)# channel-group 1 mode active
Cisco(config-if)# channel-protocol lacp
Assign the port to the channel group

[Quidway-GigabitEthernet1/0/1] eth-trunk 1
Specify the LACP port priority

[Quidway-GigabitEthernet1/0/1] lacp port-priority priority-value
[Quidway-GigabitEthernet1/0/1] quit
Specify the LACP port priority

Cisco(config-if)# lacp port-priority priority-value
Configure the LACP System priority

Cisco(config)# lacp system-priority priority-value
Configure the LACP System priority

[Quidway] lacp port-priority priority-value
Page28
VLAN Configuration Based on

Port
Huawei command
Cisco command
Vlan can be Created singly or batch:
Vlan can be Created singly or batch:
[Quidway] vlan 2
[Quidway] vlan bacth 2 to 10
Cisco(config)# vlan 2
Cisco(config)# vlan 2-10
Configure the VLAN on the access port
Configure the VLAN on the access port
[Quidway] vlan 2
[Quidway-vlan2] port GigabitEthernet1/0/1 to GigabitEthernet1/0/2

Cisco(config-if)# switchport mode access
Cisco(config-if)# switchport access vlan 2
OR
Configure the VLAN on the trunk Port

[Quidway-GigabitEthernet1/0/1] port link-type access
[Quidway-GigabitEthernet1/0/1] port default vlan 2
Configure the VLAN on the trunk Port

Cisco(config-if)# switchport trunk encapsulation dot1q
Cisco(config-if)# switchport mode trunk
Cisco(config-if)# switchport trunk allowed vlan 2-10

[Quidway-GigabitEthernet1/0/1] port link-type trunk
[Quidway-GigabitEthernet1/0/1] port trunk allow vlan 2 to 10
Page29
Voice VLAN with LLDP-MED

Switch heightens voice traffic priority (set
COS = 6) to ensure voice traffic forwarding if
the Source MAC-address of the traffic
matches the OUI configured on the Switch
DHCP Server
FTP Server
Call Agent
VLAN-ID =0 LLDP data

VLANID=8 (COS =0) Voice data
VLANID=8 (COS =6) Voice data
WAN
VLAN-ID =8 LLDP data
Switch
AR
Huawei Switch specifies the VLAN-ID of

IP Phone voice traffic as voice-vlan by
LLDP-MED
Page30

Step1: configure voicevlan
Huawei command
Cisco command
Create a VLAN as voice VLAN on the system view
Create a VLAN as voice-vlan on the configuration mode
[Quidway] vlan 8
[Quidway-vlan-8] quit

Cisco(config-vlan)# exit
Set the OUI of the voice VLAN
Enable QoS for the entire switch
[Quidway] voice-vlan mac-address mac-address mask oui-mask

[description text]
Cisco(config)# mls qos
Enable voice VLAN and trust COS on the interface

connected to IP phone
[Quidway-Ethernet1/0/1] voice-vlan 8 enable
[Quidway-Ethernet1/0/1] trust 8021p
Enable voice VLAN and trust COS on the interface

connected to IP phone
Cisco(config-if)# switchport voice vlan 8
Cisco(config-if)# mls qos trust cos
Page31

Step2: configure LLDP-MED
Globally enable LLDP on the system view
Globally enable LLDP on the configuration mode
[Quidway] lldp enable
Cisco(config)# lldp run
Enable BPDU on the interface connected IP phone
Enable LLD-MED on the interface connected IP phone

[Quidway-Ethernet1/0/1] bpdu enable

Cisco(config-if)# lldp receive
Cisco(config-if)# lldp transmit
Cisco(config-if)# lldp med-tlv-select network-policy
Page32
Basic function of STP

Switch A
Root
GE1/0/2
GE1/0/1
Switch B
STP/PVST (Cisco)
Switch D
GE1/0/1
GE1/0/2
Switch C
All switches:
Huawei command
Cisco command
Configure the spanning tree mode as STP and enable

stp on the system view
Configure the spanning tree mode as PVST on the

configuration mode
[Quidway] stp mode stp
[Quidway] stp enable

Cisco(config)# spanning-tree mode pvst
Page33
Basic function of STP

All switches:
Enable BPDU on the interfaces on the ring
[Quidway-GigabitEthernet1/0/1] bpdu enable
Configure the spanning-tree link-type as point-to-point

on the interfaces on the ring
Cisco(config-if)# spanning-tree link-type point-to-point
Switch A (root):
Configure Switch A as the root of the ring
[Quidway] stp root primary
Cisco(config)# spanning-tree vlan vlan-id root primary
OR
OR
[Quidway] stp priority 0
Cisco(config)# spanning-tree vlan vlan-id priority 0
Page34
Basic function of RSTP

Switch A Root
GE1/0/1
Switch B
GE1/0/2
RSTP/Rapid-PVST
Switch D
(Cisco)
GE1/0/2
GE1/0/1
Switch C
All switches:
Huawei command
Cisco command
Configure the spanning tree mode as RSTP and

enable stp on the system view
Configure the spanning tree mode as Rapid-PVST on

the configuration mode
[Quidway] stp mode rstp

Cisco(config)# spanning-tree mode rapid-pvst
Page35
Basic function of RSTP

All switches:
Configure the spanning-tree link-type as point-to-point

on the interfaces on the ring
Switch A (root):
[Quidway_A] stp root primary
Cisco_A(config)# spanning-tree vlan vlan-id root primary
OR
OR
[Quidway_A] stp priority 0
Cisco_A(config)# spanning-tree vlan vlan-id priority 0
Page36
Basic function of MSTP

Switch A
GE1/0/2
GE1/0/1
MSTP
Switch B
Switch D
GE1/0/1
GE1/0/2
Switch C
MSTI1 (root switch: Switch A) VLAN 1-10 --> MSTI1
MSTI2 (root switch: Switch C) VLAN 11-20 --> MSTI2
Page37

All switches:
Huawei command
Cisco command
Configure the spanning tree mode as MSTP and

enable STP on the system view
Configure the spanning tree mode as MSTP on the

configuration mode
[Quidway] stp mode mstp

Cisco(config)# spanning-tree mode mst
Configure the MST region

[Quidway] stp region-configuration
[Quidway--mst-region] region-name Huawei
[Quidway--mst-region] instance 1 vlan 1 to 10
[Quidway--mst-region] instance 2 vlan 11 to 20
[Quidway--mst-region] active region-configuration
Configure the MST region

Cisco(config)#spanning-tree mst configuration
Cisco(config-mst)#name Huawei
Cisco(config-mst)#instance 1 vlan 1-10
Cisco(config-mst)#instance 2 vlan 11-20

Page38

Switch A (root of instance 1):
Configure Switch A as the root of the instance 1
Configure Switch A as the root of the instance 1
[Quidway_A] stp instance 1 root primary
Cisco_A(config)# spanning-tree mst 1 root primary
OR
OR
[Quidway_A] stp instance 1 priority 0
Cisco_A(config)# spanning-tree mst 1 priority 0
Switch C (root of instance 2):

Configure Switch C as the root of the instance 2
Configure Switch C as the root of the instance 2
[Quidway_C] stp instance 2 root primary
Cisco_C(config)# spanning-tree mst 2 root primary
OR
OR
[Quidway_C] stp instance 2 priority 0
Cisco_C(config)# spanning-tree mst 2 priority 0
Page39
BPDU Guard
Huawei command
Cisco command
Globally enable STP and BPDU guard
Globally enable BPDU guard
[Quidway] stp bpdu-protection
Cisco(config)# spanning-tree portfast bpduguard default
Configure the interface as the edge interface and

enable BPDU on the interface
Enable the Port Fast feature

[Quidway-GigabitEthernet1/0/1] stp edged-port enable

Cisco(config-if)# spanning-tree portfast
OR
Cisco(config-if)# spanning-tree bpduguard enable
Page40
Agenda
1
Abstract

1
Basic Configuration
Reliability
QoS
Security
Device Management
Network Management
Page41
DLDP/UDLD function
Huawei command
Cisco command
Enable DLDP on the system view
Enable UDLD on the configuration mode
[Quidway] dldp enable
Cisco(config)# udld enable
Enable DLDP on the interface
Enable UDLD on the interface

[Quidway-GigabitEthernet1/0/1] dldp enable

Cisco(config-if)# udld port
Page42
Basic OSPFV2 Function

Area 0
Switch A
Area 1
VLANIF 10
192.168.0.1/2
4
VLANIF 10
192.168.0.2/2
4
VLANIF 20
192.168.1.1/2
4
VLANIF 20
192.168.1.2/2
4
Switch B
VLANIF 30
192.168.2.1/2
4
Area 2
VLANIF 30
192.168.2.2/2
4
Switch C
Switch D
Pre-conditions:
OSPF runs on the all Switches, including 3 areas in the AS
Switch A and Switch B as the ABR
Page43
Basic OSPFV2 Function

Huawei command
Cisco command
On the all Switches, configure IP addresses on the

virtual layer 3 interfaces (e.g. with Switch A)
On the all Switches, configure IP addresses on the

virtual layer 3 interfaces (e.g. with Switch A)
<Quidway_A>system-view
[Quidway_A] interface vlanif 10
[Quidway_A-Vlanif10] ip address 192.168.0.1 255.255.255.0
[Quidway_A-Vlanif10] quit
[Quidway_A] interface vlanif 20
[Quidway_A-Vlanif20] quit
Cisco_A # configure terminal

Cisco_A(config)# interface vlan 10
Cisco_A(config-if)# ip address 192.168.0.1 255.255.255.0
Cisco_A(config-if)# exit
Configure OSPF (e.g. with Switch A)
Configure OSPF (e.g. with Switch A)
[Quidway_A] ospf 100

[Quidway_A-ospf-100] area 0.0.0.0
[Quidway_A-ospf-100-area-0.0.0.0] network 192.168.0.0 0.0.0.255
[Quidway_A-ospf-100-area-0.0.0.0] quit
[Quidway_A-ospf-100] area 0.0.0.1
[Quidway_A-ospf-100-area-0.0.0.1] network 192.168.1.0 0.0.0.255
Cisco_A(config)# router ospf 100

Cisco_A(config-router)# network 192.168.0.0 0.0.0.255 area
0.0.0.0
Cisco_A(config-router)# network 192.168.1.0 0.0.0.255 area
0.0.0.1
Page44
Basic VRRP Function

Switch A
Switch B
Maste
r
Standby
VLANIF 10
209.0.0.2/24
Master
VRRP
VLANIF 10
209.0.0.3/2
4
(Switch A): priority of the VRRP group is 200
Standby (Switch B): priority of the VRRP group is 150
Page45
Basic VRRP Function

Switch A (master):
Huawei command
Cisco command
Configure a virtual layer 3 interface and assign a IP

address to the virtual layer 3 interface
Configure a virtual layer 3 interface and assign a IP

address to the virtual layer 3 interface
<Quidway_A>system-view
[Quidway_A] interface Vlanif 10
Cisco_A# configure terminal

Create a VRPP group and assign a virtual IP address

to the VRRP group
Create a VRPP group and assign a virtual IP address

to the VRRP group
[Quidway_A-Vlanif10] vrrp vrid 1 virtual-ip 209.0.0.10
Cisco_A(config-if)# vrrp 1 ip 209.0.0.10
Assign the VRRP group priority, and assign the

priority of the master of VRRP backup group is higher
than the standby one

priority of the master of VRRP backup group is higher
than the standby one
[Quidway_A-Vlanif10] vrrp vrid 1 priority 200
Cisco_A(config-if)# vrrp 1 priority 200
Page46
Basic VRRP Function

Switch B (Standby):
Configure a virtual layer 3 interface and assign another
IP address to virtual layer 3 interface
Configure a virtual layer 3 interface and assign another

IP address to the virtual layer 3 interface
[Quidway_B] interface Vlanif 10
[Quidway_B-Vlanif10] ip address 209.0.0.3 255.255.255.0

Cisco_B(config)# interface vlan 10
Cisco_B(config-if)# ip address 209.0.0.3 255.255.255.0
Create the same VRPP group and assign the same

virtual IP address to the VRRP group which configured
on the Switch A
Create the same VRPP group and assign the same

virtual IP address to the VRRP group which configured
on the Switch A
[Quidway_B-Vlanif10] vrrp vrid 1 virtual-ip 209.0.0.10
Cisco_B(config-if)# vrrp 1 ip 209.0.0.10

priority of the standby of VRRP backup group is lower
than the master one

priority of the standby of VRRP backup group is lower
than the master one
[Quidway_B-Vlanif10] vrrp vrid 1 priority 150
Cisco_B(config-if)# vrrp 1 priority 150
Page47
Multicast (PIM SM +IGMP

Snooping)
Loopback1:5.5.5.5/32
VLANIF 10
10.0.0.2/24
Switch B
Switch A
VLANIF 10
10.0.0.1/2
4
RP
VLANIF 20
20.0.0.1/24
VLANIF 20
20.0.0.2/24
PIM-SM
VLANIF 30
30.0.0.1/24
VLANIF 40
40.0.0.1/24
VLANIF 30
30.0.0.2/24
Switch C
VLANIF 40
40.0.0.2/24
IGMP
Switch E
Switch D
Pre-conditions:
IP routing between Switches and Multicast Server is normal

Switch A as RP
Page48
Multicast-PIM SM
Switch A to C:
Huawei command
Cisco command
Globally enable multicast routing function (e.g. with

Switch B)
Globally enable multicast routing function (e.g. with

Switch B)
[Quidway_B] multicast routing-enable
Enable the PIM-SM function on the virtual layer 3

interface (e.g. with Switch B)
[Quidway_B] interface vlanif 10
[Quidway_B-Vlanif20] pim sm
[Quidway_B-Vlanif20] quit

Cisco_B(config)# ip multicast-routing
Enable the PIM-SM function on the virtual layer 3

interface (e.g. with Switch B)
Cisco_B(config)# interface vlanif 10
Cisco_B(config-if)# ip pim sparse-mode
Cisco_B(config-if)# exit
Page49
Multicast-PIM SM
Switch A (RP):
Globally Switch A as RP
[Quidway_A] interface loopback 1
[Quidway_A-loopback1] ip addresss 5.5.5.5 255.255.255.255
[Quidway_A-loopback1] pim sm
[Quidway_A-loopback1] quit
[Quidway_A] pim
[Quidway_A-pim] c-rp loopback1
[Quidway_A-pim] c-bsr loopback1
Globally Switch A as RP
Cisco_A(config)# interface loopback 1
Cisco_A(config-if)# ip pim sparse-mode
Cisco_A(config)# ip pim rp-candidate loopback 1
Cisco_A(config)# ip pim bsr-candidate loopback 1
Switch B to C:
Enable IGMP on the on the virtual layer 3 interface
connected to the layer 2 multicast device (e.g. with
Switch B)
[Quidway_B-vlanif-40] igmp enable
Page50
Multicast-IGMP Snooping
Switch D to E:
Enter the configuration view
Globally enable IGMP snooping function
Globally enable IGMP snooping function
[Quidway] igmp-snooping enable
Cisco(config)# ip igmp snooping
Enable IGMP snooping on the VLAN
Enable IGMP snooping on the VLAN
[Quidway] vlan 40
[Quidway-vlan40] igmp-snooping enable
Cisco(config)# ip igmp snooping vlan 40
(Optional) Specify the IGMP version, by default, the

version is 2
[Quidway-vlan40] igmp-snooping version <1-3>
Page51
Agenda
1
Abstract

1
Basic Configuration
Reliability
QoS
Security
Device Management
Network Management
Page52
QoS marking and remarking
Name
Source IP
DSCP
Name
Source IP
DSCP
Stream
10.0.0.1
0~63
Stream
10.0.0.1
60
IP Network
Marking source IP value 10.0.0.1

to be remarked DSCP 60 on the
inbound direction of the interface
Switch
Page53

Huawei command
Cisco command
Configure an access list (e.g. IP standard access list)
Configure an access list (e.g. IP standard access list)
<Quidway>system-view
[Quidway] acl 2000
[Quidway -acl-basic-2000] rule permit source 10.0.0.1 0.0.0.0
[Quidway -acl-basic-2000] quit

Cisco(config)# access-list 1 permit 10.0.0.1 0.0.0.0
Create a traffic classifier to match the access list

[Quidway] traffic classifier c1
[Quidway-classifier-c1] if-match acl 2000
[Quidway-classifier-c1] quit
Create a traffic behavior as remark DSCP

[Quidway] traffic behavior b1
[Quidway -behavior-b1] remark dscp 60
[Quidway -behavior-b1] quit

Cisco(config)# class-map match-any c1
Cisco(config-cmap)# access-group 1
Cisco(config-cmap)# exit
Configure a traffic policy, create a traffic behavior as

remark DSCP, and then bind the traffic behavior to the
classifier
Cisco(config)# policy-map p1
Cisco(config-pmap)# class c1
Cisco(config-pmap-c)# set dscp 60
Cisco(config-pmap-c)# end
Page54

Create a traffic policy, and bind the traffic behavior to
the traffic classifier under the policy
Apply the traffic Policy to the inbound direction of the

interface
[Quidway] traffic policy p1

[Quidway-trafficpolicy-p1] classifier c1 behavior b1
[Quidway-trafficpolicy-p1] quit

Cisco(config-if)# service-policy input p1
Apply the traffic Policy to the inbound direction of the

interface
[Quidway-Ethernet0/0/1] traffic-policy p1 inbound
Page55
PQ+DRR Scheduling
10M
Internet
10M (COS=5)
Switch
250M(COS=3)
70M
IP Network
Soft Switch
200M(COS=0)
20M
IPTV
VOIP FLOW
Scheduling
Name
queue
Weight
Huawei
Cisco
IPTV FLOW
HSI FLOW
VOIP_FLOW
PQ
PQ
------
IPTV_FLOW
DRR
WFQ
70
GE
HSI_FLOW
DRR
WFQ
20
FE
Page56
PQ+DRR Scheduling
Huawei command
Cisco command
Configure the Up-link and Down-link interfaces to trust

COS of the packets
Configure the Up-link and Down-link interfaces to trust

COS of the packets
[Quidway] interface Gigabitethernet0/0/1

[Quidway-GigabitEthernet0/0/1] trust 8021p outer
[Quidway-GigabitEthernet0/0/1] exit
[Quidway-Ethernet1/0/1] trust 8021p outer
Cisco(config)# mls qos

Configure queue 5 of the Down-link Ethernet interface

as strict priority scheduling, queue 3 and queue 0 as
DRR scheduling
[Quidway-Ethernet1/0/1]qos pq 5 drr 3 0
Configure a traffic classifier to match COS value 5

Cisco(config)# class-map match-any cisco-queue-5
Cisco(config-cmap)# match cos 5
Page57
PQ+DRR Scheduling
Configure the queue 3 of the fast Ethernet interface as
DRR scheduling, and set the weights of queue 3 to 70
[Quidway-Ethernet1/0/1]qos queue 3 drr weight 70

Configure the queue 0 of the Ethernet interface as

DRR scheduling, and set the weights of queue 0 to 20
[Quidway-Ethernet1/0/1]qos queue 0 drr weight 20

Configure a traffic Policy, bind a traffic behavior to the

classifier match the COS value 5, and transmit the
match flow by Strict priority Scheduling
Cisco(config)# policy-map Cisco
Cisco(config-pmap)# class cisco-queue-5
Cisco(config-pmap-c)# priority level 1
Cisco(config-pmap-c)# police cir 100000000 bc 3125000
Cisco(config-pmap-c-police)# conform-action transmit
Cisco(config-pmap-c-police)# exceed-action drop
Cisco(config-pmap-c-police)# exit
Cisco(config-pmap-c)# exit
Cisco(config-pmap)# exit
Page58
PQ+DRR Scheduling
Cisco command
Bind traffic behaviors to the traffic classifiers match
the COS value 3 and 0, and transmit the match flow by
WFQ Scheduling
Cisco(config-pmap-c)# bandwidth percent 70
Cisco(config-pmap-c)# exit
Cisco(config-pmap-c)# bandwidth percent 20
Cisco(config-pmap-c)# end
Apply the traffic Policy to the outbound direction of

the Down-link interface
Cisco(config-if)# service-policy output Cisco
Page59
Agenda
1
Abstract

1
Basic Configuration
Reliability
QoS
Security
Device Management
Network Management
Page60
Layer 2 Suppression function

Huawei command
Cisco command
Perform storm control on the interface
Perform storm control on the interface

[Quidway-GigabitEthernet1/0/1] storm-control { broadcast |
multicast | unicast } min-rate value1 max-rate value2

Cisco(config-if)# storm-control { broadcast | multicast | unicast }
pps value2 [value1]
Specify the action when a storm is detected
Specify the action when a storm is detected
[Quidway-GigabitEthernet1/0/1] storm-control action shutdown
Cisco(config-if)# storm-control action shutdown
If you want to generate an SNMP trap when a storm is

detected
If you want to generate an SNMP trap when a storm is

detected
[Quidway-GigabitEthernet1/0/1] storm-control enable trap
Cisco(config-if)# storm-control action trap
Page61
802.1x authentication
function
Invalid Username
Invalid Password
Stop
802.1x
Intranet
Radius
Server
Valid Username
Valid Password
Permit
Pre-conditions:
IP routing between Switch and Radius Server is normal
The Radius authentication function running on Switch is normal
Page62
802.1x authentication
function
Huawei command
Cisco command
Globally enable 802.1x authentication function
Globally enable 802.1x authentication function
[Quidway] dot1x

Cisco(config)# dot1x system-auth-control
Specify the port connected to the client that is to be

enabled for 802.1x authentication
Specify the port connected to the client that is to be

enabled for 802.1x authentication

[Quidway-GigabitEthernet1/0/1] dot1x

Cisco(config-if)# switchport mode access
Cisco(config-if)# dot1x port-control auto
Configure 802.1x authentication method as radius

(commonly the domain default used to authenticate
the access user)
Configure 802.1x authentication method as radius

(commonly the domain default used to authenticate
the access user)
[Quidway-aaa] authentication-scheme default

[Quidway-aaa-authen-default] authentication-mode radius
[Quidway-aaa-authen-default] quit
[Quidway-aaa] accounting-scheme default
[Quidway-aaa-accounting-default] accounting-mode radius
Cisco(config)# aaa new-model

Cisco(config)# aaa authentication dot1x default group radiusgroup-name
Page63
Access Control Lists

Huawei command
Cisco command
Configure an access list
Configure an access list
[Quidway] acl {access-list-number | name}
[Quidway-acl-number] rule rule-number {deny | permit} accesscondition
[Quidway-acl-number] quit

Cisco(config)# access-list access-list-number {deny | permit}
access-condition

[Quidway] traffic classifier classifier-name
[Quidway-classifier-name] if-match acl {access-list-number | name}
[Quidway-classifier-name ] quit
Create a traffic behavior

[Quidway] traffic behavior behavior-name
[Quidway- behavior-name] {deny | permit}
[Quidway- behavior-name] quit
OR (configure an IP access list)

Cisco(config)# ip access-list {standard | extended} name
Cisco(config-{std|ext}-nacl)# {deny | permit} access-condition
OR (configure a Mac access list)

Cisco(config)# mac access-list extended name
Cisco(config-ext-macl)# {deny | permit} access-condition
Apply an IP ACL to the interface

Cisco(config-if)# ip access-group {access-list-number | name} {in |
out}
Page64
Access Control Lists

Create a traffic policy, and bind the traffic behavior to
the traffic classifier under the policy
[Quidway] traffic policy policy-name
[Quidway-policy-name] classifier classifier-name behavior
behavior-name
[Quidway-policy-name] quit
Apply an ACL to the interface

[Quidway-GigabitEthernet1/0/1] traffic-policy policy-name
{ inbound | outbound }
Apply an ACL to VLAN

[Quidway] vlan vlan-id
[Quidway-vlan-id] traffic-policy policy-name { inbound | outbound }
Apply a Mac ACL to interface

Cisco(config-if)# mac access-group {name} {in}
Create a vlan access-map

Cisco(config)# vlan access-map name [number]
Cisco(config-access-map)# action {drop | forward}
Cisco(config-access-map)# match {ip | mac} address access-listnumber
Cisco(config-access-map)# exit
Apply an ACL to VLAN

Cisco(config)# vlan filter access-map-name vlan-list vlan-id
Page65
Agenda
1
Abstract

1
Basic Configuration
Reliability
QoS
Security
Device Management
Network Management
Page66
Local port-mirroring function

Huawei command
Cisco command
< Quidway > system-view
Specify the observe-port on which you can observe

the packets from the mirrored interface
Specify the observe-port on which you can observe

the packets from the mirrored interface
[Quidway] observe-port 1 interface GigabitEthernet1/0/1
Cisco(config)# monitor session 1 destination interface

GigabitEthernet1/0/1
Specify the mirrored interface the direction you want

to mirror on the interface
[Quidway-GigabitEthernet1/0/2] port-mirroring to observe-port 1
{ both | inbound | outbound }
Specify the mirrored interface and the direction you

want to mirror on the interface
Cisco(config)# monitor session 1 source interface
GigabitEthernet1/0/2 { both | rx | tx }
Page67
Remote port-mirroring
function
Source
switch
RSPAN
VLAN
GE1/0/2
Intermediate
switch
GE1/0/1
Destination
switch
GE1/0/2
GE1/0/1
RSPAN
VLAN
GE1/0/1
RSPAN
source port
GE1/0/2
RSPAN
destination port
Source switch:
Huawei command
Cisco command
Create RSPAN VLAN on the system view
Configure RSPAN VLAN on the configuration mode
[Quidway] vlan 900

Cisco(config-vlan)# remote span
Page68
function
Source switch:
Configure the RSPAN VLAN on the Up-link Port
Configure the RSPAN VLAN on the Up-link Port

[Quidway-GigabitEthernet1/0/2] port trunk allow vlan 900

Cisco(config-if)# switchport trunk allowed vlan 900
Specify the RSPAN session and the destination

RSPAN VLAN
Specify the RSPAN session and the destination

RSPAN VLAN
[Quidway] observe-port 1 interface GigabitEthernet1/0/2 VLAN 900
Cisco(config)# monitor session 1 destination remote vlan 900
Specify the RSPAN source port and the direction you

want to mirror on the port
[Quidway-GigabitEthernet1/0/1] port-mirroring to observe-port 1
{ both | inbound | outbound }
Specify the RSPAN source port and the direction you

want to mirror on the port
Cisco(config)# monitor session 1 source interface
GigabitEthernet1/0/1 { both | rx | tx }
Page69
function
Intermediate switch:
Configure RSPAN VLAN on the configuration view
[Quidway] vlan 900
[Quidway-vlan900] quit

Add the ports to the RSPAN VLAN in trunk mode

Add the ports to the RSPAN VLAN in trunk mode

Page70
function
Destination switch :
Configure RSPAN VLAN on the configuration mode
[Quidway] vlan 900

Add the port connected with the Intermediate switch to

the RSPAN VLAN in trunk mode, and add the RSPAN
destination port to the RSPAN VLAN in access mode
Add the port connected with the Intermediate switch to

the RSPAN VLAN in trunk mode

[Quidway-GigabitEthernet1/0/2] port default vlan 900

Specify the RSPAN session and the RSPAN

destination port
Cisco(config)# monitor session 1 destination interface
GigabitEthernet1/0/2
Specify the RSPAN session and the source RSPAN

VLAN
Cisco(config)# monitor session 1 source remote vlan 900
Page71
Agenda
1
Abstract

1
Basic Configuration
Reliability
QoS
Security
Device Management
Network Management
Page72
Radius function
Huawei command
Cisco command
Configure a Radius template, set the Authentication

key and Identify the radius Server
Set the Authentication key

Cisco(config)# radius-server host 200.0.0.1 key 123456
[Quidway] radius-server template Huawei

[Quidway-radius-Huawei] radius-server shared-key 123456
[Quidway-radius-Huawei] radius-server authentication 200.0.0.1
[Quidway-radius-Huawei] radius-server accounting 200.0.0.1
Enter AAA view

[Quidway] aaa

Configure the radius Servers group

Cisco(config)# aaa group server radius Huawei
Cisco(config-sg-radius)# server 200.0.0.1
Cisco(config-sg-radius)# exit
Page73
Radius function
Configure authentication and accounting schemes,
then Identify authentication and accounting mode as
radius to the schemes
[Quidway-aaa] authentication-scheme Huawei
[Quidway-aaa-authen-Huawei] authentication-mode radius
[Quidway-aaa-authen-Huawei] quit
[Quidway-aaa] accounting-scheme Huawei
[Quidway-aaa-accounting-Huawei] accounting-mode radius
[Quidway-aaa-accounting-Huawei] quit
Configure a domain, Identify the authentication and

accounting mode of the domain as radius, and specify
the server template
Identify the authentication, authorization and

accounting mode as radius to the radius Server group
Cisco(config)# aaa authentication login default group Huawei
Cisco(config)# aaa authorization network default group Huawei
Cisco(config)# aaa authorization exec default group Huawei
Cisco(config)# aaa accounting exec default start-stop group
Huawei
Cisco(config)# aaa accounting network default start-stop group
Huawei
Configure authentication-mode of the VTY as AAA

Cisco(config)# line vty 0 4
Cisco(config-line)# login authentication default
[Quidway-aaa] domain Huawei

[Quidway-aaa-domain-Huawei] authentication-scheme Huawei
[Quidway-aaa-domain-Huawei] accounting-scheme Huawei
[Quidway-aaa-domain-Huawei] radius-server Huawei

Page74
HWTACACS function
Huawei command
Cisco command
Configure a TACACS template, set the authentication

key and Identify the HWTACACS Server
Identify the TACACS Server and set the authentication

key
[Quidway] hwtacacs-server template Huawei

[Quidway-hwtacacs-Huawei] hwtacacs-server shared-key 123456
[Quidway-hwtacacs-Huawei] hwtacacs-server authentication
10.0.0.1
[Quidway-hwtacacs-Huawei] hwtacacs-server authorization
10.0.0.1
[Quidway-hwtacacs-Huawei] hwtacacs-server accounting
10.0.0.1
Cisco(config)# tacacs-server host 10.0.0.1 key 123456
Enter AAA view

[Quidway] aaa

configure the TACACS Server group

Cisco(config)# aaa group server tacacs+ Huawei
Cisco(config-sg-tacacs+) # server 10.0.0.1
Cisco(config-sg-tacacs+) # exit
Page75
HWTACACS function
Configure authentication, authorization and accounting
schemes, then Identify authentication, authorization
and accounting mode as HWTACAS to the schemes
[Quidway-aaa] authentication-scheme Huawei
[Quidway-aaa-authen-Huawei] authentication-mode hwtacacs
[Quidway-aaa-authen-Huawei] quit
[Quidway-aaa] authorization-scheme Huawei
[Quidway-aaa-author-Huawei] authorization-mode hwtacacs
[Quidway-aaa-author-Huawei] quit
[Quidway-aaa] accounting-scheme Huawei
[Quidway-aaa-accounting-Huawei] accounting-mode hwtacacs
[Quidway-aaa-accounting-Huawei] quit
Configure a domain, Identify the authentication,

authorization and accounting mode of the domain as
HWTACACS, and specify the server template
Configure the authentication, authorization and

accounting mode as TACACS to the TACACS Server
Cisco(config)# aaa authentication login default group Huawei
Cisco(config)# aaa authorization network default group Huawei
Cisco(config)# aaa authorization exec default group Huawei
Cisco(config)# aaa accounting exec default start-stop group
Huawei
Cisco(config)# aaa accounting network default start-stop group
Huawei

Cisco(config)# line vty 0 4
Cisco(config-line)# login authentication default
[Quidway-aaa] domain Huawei

[Quidway-aaa-domain-Huawei] authentication-scheme Huawei
[Quidway-aaa-domain-Huawei] authorization-scheme Huawei
[Quidway-aaa-domain-Huawei] accounting-scheme Huawei
[Quidway-aaa-domain-Huawei] hwtacacs-server Huawei

Page76
Web management
Intranet
Web
Server
Pre-conditions:
IP routing between Switch and Web management Server is normal
Page77
Web management
Huawei command
Cisco command
Globally enable HTTP Server function
Globally enable HTTP Server function
[Quidway] http server enable

Cisco (config)# ip http server
Configure the HTTP user and the password of the user
Configure the local user and the password of the user
[Quidway] aaa

[Quidway-aaa] local-user Huawei service-type http

[Quidway-aaa] quit
Log in device by local through HTTP

Cisco (config)# ip http authentication local
Page78
SNMP v1/v2c function

Huawei command
Cisco command
Enable SNMP agent function
[Quidway] snmp-agent
Set version of SNMP as v1 or v2c, by default, the

version is all
[Quidway] undo snmp-agent sys-info version all
[Quidway] snmp-agent sys-info version v1/v2c
Set version of SNMP as v1 or v2c, by default, the

version is v1
Cisco(config)# no snmp-server
Set the SNMP community name
Set the SNMP community name

[Quidway] snmp-agent community read public
[Quidway] snmp-agent community write private
Cisco(config)# snmp-server community public ro

Cisco(config)# snmp-server community private rw
Page79
SNMP v3 function
Huawei command
Cisco command
Enable SNMP agent function on the system view
[Quidway] snmp-agent
Set the version of SNMP as 3, the default version is v1

Set version of SNMP as v3, the default version is all
Cisco(config)# no snmp-server
[Quidway] undo snmp-agent sys-info version all
[Quidway] snmp-agent sys-info version v3
Add users into the SNMPv3 user group
Configuring an SNMPv3 User Group
Cisco(config)# snmp-server group Huawei v3 {auth | noauth }
[Quidway] snmp-agent group v3 Huawei [authentication]
Add an user into the SNMPv3 user group and need to

authenticate (e.g. with MD5)
Add an user into the SNMPv3 user group and need to

authenticate (e.g. with MD5)
Cisco(config)# snmp-server user 8031 Huawei V3 auth md5

123456
[Quidway] snmp-agent usm-user v3 8031 Huawei authenticationmode md5 123456
Page80
SNMP Trap
Huawei command
Cisco command
Enable the system view
Specify hosts to receive SNMP notifications
Specify hosts to receive SNMP notifications
[Quidway] snmp-agent target-host trap address udp-domain

192.180.1.27 params securityname public v2c
Cisco(config)# snmp-server host 192.180.1.27 version 2c public
Enable the switch to send traps or specify the type of

notifications to be sent
[Quidway] snmp-agent trap enable [ trap-type ]
Enable the switch to send traps or specify the type of

notifications to be sent
Cisco(config)# snmp-server enable traps [ trap-type ]
Page81
Thank you
www.huawei.com

Huawei Cisco Xref Switch CLI PDF

Uploaded by

Document Informationclick to expand document information

Document Informationclick to expand document information

Copyright:

Available Formats

Huawei Cisco Xref Switch CLI PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Huawei Cisco Xref Switch CLI PDF

Uploaded by

Copyright:

Available Formats

HUAWEI Switch CLI

Copyright 2013 Huawei Technologies Co., Ltd. All rights reserved.

Upon completion of this course, you will be able to:

Understand the characteristic of Huawei CLI

Be familiar with some common Huawei commands

Configure some basic Huawei Switch features

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Huawei and Cisco command-view contrast

Switch Features configuration contrast

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

The overall mechanism of Huawei and Cisco CLI are similar.

The styles of Huawei and Cisco CLI are identical.

Huawei CLI has corresponding relationship with Cisco's in

After learning these sameness and differences between

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Huawei and Cisco command-view contrast

Command style contrast

Common commands contrast

Switch Features configuration contrast

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Command style contrast

Huawei configuration views and Cisco configuration modes contrast

User mode, use > as prompt, e.g. Cisco>

Privileged mode, use # as prompt, e.g. Cisco#

Configuration mode, use # as prompt, e.g. Cisco(config)#

Other configuration mode, use # as prompt, e.g. Cisco(config-XX)#

User view, use < > as prompte.g. <Huawei>

System view, use [ ] as prompt, e.g. [Huawei]

Other configuration view, use [ ] as prompt, e.g. [Huawei-XX]

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Command style contrast

Command structure contrast

Huawei and Cisco have similar command structure

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Command style contrast

Common shortcut keys contrast

The same to use ? to help to find the following command/parameter

The same to use Tab key to full fill the command

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Huawei and Cisco command-view contrast

Command style contrast

Common commands contrast

Switch Features configuration contrast

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Common command contrast

Command keywords contrast

show <- -> display

no <- -> undo

exit <- -> quit

clear <- -> reset

debug <- -> debugging

neighbor <- -> peer

detail <- -> verbose

delete <- -> delete

match <- ->if-match

Copyright 2010 Huawei Technologies Co., Ltd. All rights reserved.

Common command contrast