Konica Minolta 1600f DTS LFF3 4 en
Konica Minolta 1600f DTS LFF3 4 en
Konica Minolta 1600f DTS LFF3 4 en
1600f
-2-
CONTENTS
DESCRIPTIVE NOTICE
INSTALLATION GUIDE
MAINTENANCE GUIDE
PERSONNALISATION
-1-
DESCRIPTIVE NOTICE
CONTENTS
2 2 3 3 3 4 6 7 7 9 9 15 15 16 16 16 17 23
2 CHARACTERISTICS 2.1 2.2 2.3 PHYSICAL CHARACTERISTICS GENERAL TECHNICAL CHARACTERISTICS GENERAL CHARACTERISTICS OF THE CONSUMABLE
3.2 CPU CARD Electronical architecture Power supply Quartz Reset 4 PRINTING 4.1 4.2 4.3 PRINTER LANGUAGE INTERNAL FONTS LIST PAPER FORMAT
-2-
Front
LCD display
Front panel Smart card reader Paper output Printer Manuel paper feed tray Output stacker
Paper tray
Back
LAN Connection (model LFF4) Master USB connection (USB key) (model LFF3) Slave USB connection (for PC) Additional telephone cable socket Telephone cable socket Power supply cord connection
On/Off switch
-3-
-4-
Inapa tecno SPEED A4 - 80 g/m2 Ricoh T6200 A4 - 70 g/m2 ITU #1 - A4 3% Normal mode (200 x 100 DPI) CIS Color and B/W Yes 600 256 36 bits/pixel A4 (210 x 297 mm) 216 mm 145 mm 1m 120 mm 60 to 90 g/m 50 pages (80 g/m) 210 mm 25 % to 400 % Yes (7 levels) Yes (7 levels) Yes Yes CIS Color and B/W Yes 600 x 2400 256 36 bits/pixel 220 mm x 304 mm Letter (215.9 x 279.4)
-5-
Zoom in steps of 1 % Contrast Brightness Printer Type Printer language Resolution in DPI Maximum paper width (in mm) Paper feed tray Page capacity (in pages) Paper weight Manual paper feed Capacity of pages (in pages) Paper weight Transparent (laser printer compatible) Page capacity of the output tray Printing on enveloppes Printer speed First page printed after Printing time at start-up Printing area (in mm) Consumable for RD document Maximum initial toner cartridge capacity (in pages A4 ratio 5 %) Management of consumables (depending on model) Weight of toner cartridge (in Kg) Toner saving function Copier Type Input resolution (optical) in DPI Output resolution in DPI Maximum paper size (in mm) Maximum speed for 300 x 300 (RP) resolution Maximum speed for 300 x 300 resolution (Legal) First page printed after Multicopy Zoom Zoom steps Collated copies Keyboard and screen Keyboard Screen
Terminal 25 % to 400 % Yes (7 levels) Yes (7 levels) Laser B/W GDI 600 x 600 Legal (215.9 x 355.6) 250 (64g) / 200 (80g) 60 to 105 g/m2 1 52 to 162 g/m2 Yes 50 Yes (Manual paper feed) 16 PPM 13 s 21 s 201.54 x 287 2 200 / 4 000 By smart card 1.2 Yes Black/White 300 x 300 (fast) or 600 x 600 (quality) 600 x 600 Legal (215.9 x 355.6) 16 PPM 14 PPM 13 s 1 to 99 25 % to 400 % 1% Yes 62 keys 2 lines de 16 characters + 7 icons
-6-
Terminal LAN access (model LFF4) Type Plug and Play configuration Internet Protocol DNS Fax-Modem Type Maximum speed in bps (V34Fax) V34Fax capacity in bps Incrementation in bps V17 capacity in bps V29 capacity in bps V27ter capacity in bps Fax communication Type Maximum speed in bps (V34Fax) Coding ECM Time to transmit RD Type of transmission Max. send delay PSTN redial SMS communication Transmission Reception Mailing Directory Capacity Type Transmission list Transmission list capacity Alphabetical typing Associated key Import/export directory on PC Save directory on PC Geographical settings Countries Network Languages Ethernet 10/100 base T DHCP & BOOTP TCP / IP 2 DNS server access PSTN-Super G3 33 600 33 600 to 2 400 2 400 14 400, 12 000, 9 600, 7 200 9 600, 7 200 4 800, 2 400 PSTN, ITU T-30, G3 33 600 MH, MR, MMR, JBIG T30 ECM 2.5 s Memory and direct (ADF) 24 hours last 10 numbers Yes (V23) No 10 directly 249 from directory 250 Name / PSTN and SMS number 32 249 Yes Yes XML, EAB and CSV formats XML format 19 TTBR21 14
-7-
The values of the consumables counter are regularly updated in the EEPROM memory. Each time the machine is switched on, the counter is read in the the EEPROM memory.
3. OPERATION
The equipment is a Group 3 multifunction fax functioning in accordance with the UIT-T T30 recommendation. It consists of a laser printer, a CIS (Contact Image Sensor) color ADF scanner, a color flatbed scanner, a front panel with an alphanumerical keyboard and a LCD display with 2 lines of 16 characters (refer to the User Guide for a more complete description of the front panel ). It allows the following operations to be carried out: Fax transmission and reception on the switched telephone network using the V34 protocol (max. 33.6 kbits/s) and the V17 protocol (max. 14.4 kbits/s), SMS (Short Message Service) transmission on the switched telephone network using the V23 protocol, Network printer and scanner, via a local area network (LAN), E-mail transmission and reception on the local area network (model LFF4). photocopying documents, local printing and scanning for PC via USB or WLAN connections. The machines electronics is made up of a front panel card and a CPU card. The power supply is provided by the printer. Before performing any operations on the electronic CPU card, you should: 1 - Set the On/Off button to Off (position 0). 2 - Unplug all external connectors (phone line connectors, USB connectors master, slave, LAN). 3 - Unplug the power supply cord.
Smart card
P4001
CPU connection
P4200
-8-
CPU - P4200: CPU connection Pin Signal 1-7-8-10-15 GND 2 FERCAP 3 CVCC 4 5 6 9 11 12 13 14 16 CLKPUCE RSTPUCE IOPUCE SCLKPUP RXPUP TXPUP STROB1 STROB2 P5V
Utilization Ground Detection of smart card Smart card power supply (3.3V) (controlled by I/O CVCC) Smart card clock Smart card reset Smart card data Serial clock link for differential registers Sending data from the front panel Sending data from the CPU Out-of-register strobe to control the keyboard Out-of-register strobe to control the display 5V power supply Utilization Ground LCD contrast Selection of registers Read or Write (driver configured to write in 0V) Enable Signal (active at 1) Vcc: 4.5V to 5.5V Data (Bit 4) Data (Bit 5) Data (Bit 6) Data (Bit 7) Utilization Smart card power supply (3.3V) Smart card reset Smart card clock Not connected Ground Not connected Smart card data (input/output) Not connected Ground Smart card detection
LCD - P4002: LCD interface Pin Signal 1 GND 2 V0 3 RS 4 R/W 5 6 7 8 9 10 LCD_E VCCLCD DB4 DB5 DB6 DB7
Smart card - P4001: connection with the smart card Pin Signal Input/Output 1 CVCC O 2 RSTPUCE O 3 CLKPUCE O 4 5 GND 6 7 IOPUCE I/O 8 S1 GND S2 FERCAP I
-9-
- 10 -
CN1
CN2
CN5
CN6 CN7
CN4 C N 1 0
C N 1 1
CIS P4380
C N 9
C N 3
Printer
List of connectors: Connector Printer Loudspeaker Front panel ADF scanner motor Flatbed scanner motor CIS Phone line External phone line LAN (model LFF4) USB Slave USB Master USB Master (model LFF3)
Topography CNx P1650 P4100 P4301 P4302 P4380 P4420 P4440 P8800 P4901 P4950 P4960
Number of points 2 16 15 5 12 4 4 8 4 4 4
Sex Female Female Female Female Female Female Female External, type USB type B External, type USB type A External, type USB type A
- 11 -
Pin 1 2 3 4 5
Signal +24VS GND XPMENA XSCRDY PMCLK +5VLD XLDENA APCSH XDETP GND XVD NC P24VS GND P5V XMMEN A MMCLK MMCW XMMLOC K MMGAIN FANEMA GND FANLOC K +24VS XFPCL
Input/ Output S E
Utilization 24V power supply Ground Starting the polygon motor Locking the polygon motor Polygon motor clock Activating the laser Sampling Ray beam detector Ground Diode laser video Not connected 24V power supply Ground
CN2
Diode laser 1 2 3 4 5 6 7 O O I O -
CN3
Printer motor 1 2 3 4 5 6 7 8
CN4
CN5
Paper output clutch 1 2 O 24V power supply Electric paper clutch signal Ground Paper feed signal captor 5V power supply Register of signal captors Manual paper feed signal captor Ground Four paper output signal captors 5V power supply
CN6
Paper detection captors 1-4-7 2 3-6-9 5 8 GND XFEED +5V XREGIST XMANUA L GND XEXIT +5V I I I I -
CN7
CN9
Debug
- 12 -
Topography
Connector
Pin 1 2 3 4
Signal +5V DBGRXD DBGTXD GND TRAPWM 0 TRAPWM 1 BIASPW M CHEPWM XTRACT L XBIASCT L GND +24VS HTON ZEROC HTEN GND P24VS +24V GND +5V FTEMP GND P24V P24VS XAIO GND TEMP GND
Input/ Output I O O O O O O O O I O O I I O I I -
Utilization 5V power supply Debug receipt Debug command Ground PWM signal for transfer of charger (+) PWM signal for transfer of charger (-) PWM development signal PWM signal charger Charger signal transferred to On Development signal Ground 24V power supply Phase Fuser control Control signal Fuser relay (Activated to H) Ground 24V power supply 24V power supply Ground 5V power supply Fuser temperature detector Ground 24V power supply 24V power supply Detection of cartridge Ground Detection of printer motor temperature Ground
CN10
CN11
CN12
Temperature captor 1 2
CN13
Opening of printer cover captor 1 2 IAO captor (presence of toner) 1 2 Motor temperature captor 1 2
CN15
CN16
- 13 -
Loudspeaker - P1650: connection with the loudspeaker Pin Signal Input/Output Utilization 1 HPP O Differentiated BF signal to HP 2 HPN O Differentiated BF signal to HP Frontpanel - P4100: connection with the front panel card Pin Signal Input/Output Utilization 1 P5V 5V power supply 2-7-9-10-16 GND Ground 3 STROB2 Out-of-register strobe to control the display 4 STROB1 Out-of-register strobe to control the keyboard 5 TXPUP O Data emitted by the CPU 6 RXPUP I Data emitted by the front panel 8 SCLKPUP O Serial link clock for differentiated registers 11 IOPUCE I/O Smart card data (3.3V) 12 RSTPUCE O Smart card reset 13 CLKPUCE O Smart card clock 14 CVCC O Smart card power supply (3.3V) (controlled byr I/0 CVCC) 15 FERCAP I Detection of smart card ADF scanner motor - P4301 : connection with the ADF scanner motor Pin Signal Input/Output Utilization 1 P24V 24V power supply 2 ADF_BN O scanner motor coil BN 3 ADF_B O scanner motor coil B 4 ADF_AN O scanner motor coil AN 5 ADF_A O scanner motor coil A 6 GND Ground 7 PSF I Sheet sensor 8 P5V 9 GND Ground 10 OUVCAP I ADF cover sensor 11 P5V 12 GND Ground 13 STSC I Document ready sensor 14 P5V 15 NC Not connected
Flatbed scanner motor - P4302: connection with the flatbed scanner motor Pin Signal Input/Output Utilization 1 P24V 24V power supply 2 FTB_BN O scanner motor coil BN 3 FTB_B O scanner motor coil B 4 FTB_AN O scanner motor coil AN 5 FTB_A O scanner motor coil A
- 14 -
Phone line - P4420 Pin Signal 1 R1 2 L1 3 L2 4 R2 External phone line - P4440 Pin Signal 1 NC 2 L1 3 L2 4 NC LAN - P8800 (model LFF4) Pin Signal 1 TXLANP 2 TXLANN 3 RXLANP 4 REF1 5 REF1 6 RXLANN 7 REF2 8 REF2
Utilization Loopback Phone line Phone line Loopback Utilization Phone line Phone line
Utilzsation Differential pair Differential pair Differential pair Polarization 1 Polarization 1 Differential pair Polarization 2 Polarization 2 Utilization CIS video 300/600dpi resolution command CIS voltage reference Mass CIS (synchro point) pixel clock 5V power supply Start Pulse CIS (line synchro) leds power supply (in voltage) Blue led cathod Green led cathod Red led cathod Ground Utilization Power supply provided by the master Differential pair Differential pair Ground Utilization Power supply provided to the slave Differential pair Differential pair Ground
CIS - P4380: connection with the CIS Pin Signal Input/Output 1 VIDCIS I 2 CMD RESOL O 3 VREFCIS O 4 VIDEOGND 5 CLKCIS O 6 ALIMCIS 7 SPCIS O 8 ALIMLED O 9 GNDLEDB O 10 GNDLEDV O 11 GNDLEDR O 12 GND USB - P4901: USB slave interface Pin Signal Input/Output 1 VBUS_USB I 2 3 4 USBN USBP GND I/O I/O I/O
USB - P4950: USB master interface Pin Signal Input/Output 1 VBUS_USB_HO O ST 2 USBN I/O 3 USBP I/O 4 GND I/O
- 15 -
USB - P4960: USB master interface (model LFF3) Pin Signal Input/Output 1 VBUS_USB_HO O ST_2 2 USBN I/O 3 USBP I/O 4 GND I/O 3.2.2 POWER SUPPLY The 24V and 5V power supply are provided by the printer. Diagram of printer power supply connections:
Utilization Power supply provided to the slave Differential pair Differential pair Ground
24 V
Resistor 12 V regulator Z4051 OECIS* Resistor Z4376 +5V regulator Z150 +5V regulator
+ 24 V
CIS
gen LED current
CIS
CAN anavcc
Z4050
5V
VCC
+ 3,3 V regulator
+ 3,3 V : P3V3
printing (16,723MHz)
32,768 MHz
29,4912 MHz
Modem 1
6 MHz
USB controller
OSC1
16 MHz
MCV
HD64F3048
- 16 -
3.2.4 RESET The reset is generated from 3.3V as all logical parts (DIGICOLOR2, memory, ) are supplied in 3.3V. The reset is active during at least 100ms. Printers reset diagram:
3.3 V
DIGICOLOR2
Flash storage
5V
XRES
MCV HD64F3048
- 17 -
- 18 -
- 19 -
- 20 -
- 21 -
- 22 -
- 23 -
-1-
INSTALLATION GUIDE
CONTENTS
1 INSTALLATION REQUIREMENTS 1.1 1.2 1.3 FUNCTIONAL SPACE REQUIREMENTS MAINS POWER CORD ENVIRONMENTAL CONDITIONS 3 3 3 3 4 4 4 4 5 5 6 6 6 6 7 7 7 8 8 8 9 9 9 9 10 10 10 11 11 11 12 12
2 UNPACKING THE TERMINAL 3 INSTALLING THE TERMINAL 3.1 3.2 3.3 3.4 3.5 INSTALLING THE TERMINAL INSTALLING THE FRONT PANEL (DEPENDING ON THE MODEL) INSTALLING THE DOCUMENT FEEDER INSTALLING THE TONER CARTRIDGE INSTALLING THE PAPER TRAY
4 CONNECTIONS 4.1 4.2 4.3 CONNECTING THE PHONE LINE CONNECTING THE POWER SUPPLY AND SWITCHING ON THE MACHINE PC CONNECTIONS 4.3.1 PC connections via USB 4.3.2 PC connections via WLAN
5 GETTING STARTED AND SOFTWARE CONFIGURATION 5.1 5.2 5.3 USER PARAMETERS INSTALLATION PARAMETERS LIST OF CONFIGURATIONS (SOS) 5.3.1 Soft-switch 1 : Tuning the ringing tone and automatic printing 5.3.2 Soft-switch 2 : Scanner/printer configuration 5.3.3 Soft-switch 3 : Line configuration 5.3.4 Soft-switch 4 : Fax protocol configuration 5.3.5 Soft-switch 5 : Voice/Loudspeaker configuration 5.3.6 Soft-switch 6 : Line adjustment 5.3.7 Soft-switch 8 : Remote readabout / Internal answering machine / Modem 5.3.8 Soft-switch 9 : Approval + communication Applications 5.3.9 Soft-switch 10 : Communications : Locks/Miscellaneous 5.3.10 Soft-switch 13 : Intranet (model LFF4) 5.3.11 Soft-switch 14 : Intranet (model LFF4)
-2-
5.3.12 5.3.13 5.3.14 5.3.15 5.3.16 5.3.17 5.3.18 5.3.19 5.3.20 5.3.21 5.3.22 5.3.23 5.3.24 5.3.25 5.3.26 5.3.27 5.4
Soft-switch 15 : Intranet (model LFF4) Soft-switch 16 : Intranet (model LFF4) Soft-switch 17 : Intranet (model LFF4) Soft-switch 18 : Coding / UART Rate Soft-switch 19 : Miscellaneous software functions Soft-switch 21 : T4 Decodeur / Debug Soft-switch 22 : Miscellaneous Soft-switch 23 : Miscellaneous Soft-switch 24 : SMS / IEEE Adress Soft-switch 25 : Miscellaneous (model LFF4) Soft-switch 26 : Miscellaneous Soft-switch 27 : Miscellaneous Soft-switch 28 : SMS Soft-switch 29 : Miscellaneous Soft-switch 31 : Miscellaneous Soft-switch 33 : Miscellaneous
12 13 13 13 14 14 14 15 15 15 16 16 17 17 17 17 18 18 18 19 20 20 21 21 21 22 22 22 24 25 26
DOWNLOADING THE SOFTWARE 5.4.1 Downloading via a PC connection 5.4.2 Download via STN 5.4.3 Downloading with the miniboot 5.4.4 Downloading with the miniboot 5.4.5 Downloading via Local Network
6 REMOTE READABOUT 6.1 6.2 6.3 6.4 ENABLING THE REMOTE READABOUT TRIGGER CRITERIA INITIAL CONSUMABLES DESCRIPTION OF THE TRANSMITTED DATA 6.4.1 Format of transmitted data in transparent mode 6.4.2 Remote Readabout Report 6.4.3 Description of the parameters REMINDERS
6.5
7 STORING USER PARAMETERS AND ACTIVITY COUNTERS ON THE TERMINAL26 8 PACKING AND TRANSPORTING THE MACHINE 27
-3-
412 mm
6 38
447 m
-4-
Never place the machine directly on the floor. Always place the machine on a sturdy, flat surface. Always keep the machine away from hanging objects and any inflammable products.
Phone cord
Front panel
Installation Guide CDRom containing the User Guide booklet (UG) and the Companion suite software Smart card
Toner cartridge
2 - Apply pressure on the front section of the front panel (B) to click it into place.
-5-
4 - Insert the cartridge into its compartment by pushing it to the end until it clicks into place (last movement downwards).
-6-
4. CONNECTIONS
Front Back
D* E** F
I
* model LFF4 ** model LFF3
-7-
5 - Depending on the model, after the initialization phase, WAITING FOR INIT appears on the screen. Insert the initialization card provided in the smart card reader.
After the analysis phase, INIT. OK - REMOVE CARD appears on the screen. Remove the initialization card from the smart card reader. Remark(s) : By default, the terminal is set in English. The language can be changed in the User parameters (see User Guide booklet).
4.3 PC CONNECTIONS
Users can install and configure their terminal on their PC as a local printer and scanner. There are two ways of connecting the terminal to a PC : via a USB connection, via a WLAN connection. This section only describes physical connections. Refer to the User Guide booklet for more information on configuring the terminal to a PC. 4.3.1 PC CONNECTIONS VIA USB Remark(s) : Before connecting the terminal to a PC, the Companion Suite software must be installed on the PC (Refer to the User Guide booklet for the detailed procedure).
1 - Connect the end of the USB cable into the USB slave connector (E) located at the back of the terminal.
2 - Connect the other end of the USB cable into a USB port on the PC. 4.3.2 PC CONNECTIONS VIA WLAN Remark(s) : Before connecting the terminal to a PC, the WLAN connection and the Companion Suite software must be installed on the PC (Refer to the User Guide booklet for the detailed procedure).
-8-
1 - Plug in the electronic WLAN key into the USB master connector (A) located at the front of the terminal.
Access to these parameters is only authorized for the maintenance and/or installation service technicians. The terminal comes with software blocks called SOS (Soft Switchs) N 1 to 60. Each block is made up of 8 bits called bit 1 to 8. Each bit has a value of 0 or 1. Reading the block (from bit 1 to bit 8) on the display panel is done from right to left. The blinking cursor is always located on the bit 8 (on the extreme left) when selecting the configuration. Access to the configuration bytes is available via the initialization screen, via a succession of keys:
*#
The significance of the principal configuration parameters for the terminal are provided below. They can be modified just like any other parameter.
-9-
Bit 1 2 3 4 5 6 7 8 Bit 1 2 3 4
5 6 7 8
- 10 -
Bit 1 2 3
4 5
6 7 8
5.3.4 SOFT-SWITCH 4 : FAX PROTOCOL CONFIGURATION Value Description 1 SOS-MODPRIV : Communication in private mode Values : 0 (Without)# 1 (With) 0 SOS-DIS-COURT : Restricted DIS size Values : # 0 (long DIS (complete)) 1 (Short DIS) 0 SOS-TCF : TCF accept criterion Values : # 0 (Normal): refused if there has not been 1 continuous second. 1 (Special): 1 discontinuous second in the TCF, then accepted systematically at 2 400 b/s. 0 SOS-RTN : Page accept criterion 0 Values : # 0 (10 percent) 1 (15 percent) 2 (20 percent) 3 (no check) 1 SOS-DISINF : Unlimited DIS length Values : 0 (Without)# 1 (With) 0 SOS-LGINF : Maximum length of scan, printing, communication Values : # 0 (1 meter) 1 (3 meters) 1 SOS-ECM : Restricted ECM Values : 0 (Without) # 1 (With) 5.3.5 SOFT-SWITCH 5 : VOICE/LOUDSPEAKER CONFIGURATION Value Description 1 Reserved 0 Reserved 0 Reserved 0 Reserved 0 SOS-HP : Line monitoring during fax comm. Values : # 0 (Without) 1 (With) 1 Reserved 1 Reserved 0 Reserved 5.3.6 SOFT-SWITCH 6 : LINE ADJUSTMENT Value Description 0 Reserved 0 Reserved 0 Reserved 0 Reserved 0 Reserved 0 Reserved 0 Reserved 0 SOS-TSTDCOM : Driver test functions Values : # 0 (Without)1 (With)
Bit 1 2 3 4 5 6 7 8 Bit 1 2 3 4 5 6 7 8
- 11 -
Bit 1 2 3 4 5 6 7 8 Bit 1 2 3 4 5 6 7 8
5.3.7 SOFT-SWITCH 8 : REMOTE READABOUT / INTERNAL ANSWERING MACHINE / MODEM Value Description 0 SOS-TLR : Remote readout enable (ATTENTION!!) Values : # 0 (No remote readout) 1 (Remote readout enabled) 1 Reserved 1 Reserved 0 Reserved 1 Reserved 1 Reserved 0 Reserved 1 Reserved 5.3.8 SOFT-SWITCH 9 : APPROVAL + COMMUNICATION APPLICATIONS Value Description 0 Reserved 1 Reserved 1 Reserved 0 SOS-REPERR: Redialing from page fault Values : 0 (Without) # 1 (With) 1 SOS-NOTREMIS : Printing of first page on trasmission rapport Values : 0 (Without) # 1 (With) 1 SOS-GRILLAGE : Burn phone numbers Values : 0 (Without) # 1 (With) 0 SOS-LIGNE5S : Lines of 5 sec.during reception Values : # 0 (Length of lines not limited to 5 sec./line) 1 (Maximum length of a line: 5 seconds) 1 SOS-AGRE-FRA : Fench approval functions Values : 0 (Without) # 1 (With) 5.3.9 SOFT-SWITCH 10 : COMMUNICATIONS : LOCKS/MISCELLANEOUS Value Description 0 SOS-AFFVIT : Communication rate display Values : # 0 (Without) the page number is displayed. 1 (With) the comm. rate is displayed. 1 SOS-BTYPNUM : Access to impulse/DTMF parameter Values : 0 (With) Reserved # 1 (Without) 0 Reserved 1 Reserved 1 SOS-TLRFAX : Remote readout by fax (ATTENTION!!!) Values : # 0 (Remote readout to Quadrige in transparent mode) 1 (Remote readout by fax) 0 Reserved 0 SOS-SONREA : Access to redialing parameters (screen /printer) Values : # 0 (No access)1 (With access) 0 Reserved
Bit 1 2 3 4 5 6 7 8
- 12 -
Bit 1 2 3 4 5 6 7 8
5.3.10 SOFT-SWITCH 13 : INTRANET (MODEL LFF4) Value Description 0 SOS-BRIDEMAIL: Restricted text e-mail reception Values: # 0 (No)1 (Yes) 1 SOS-ACKNORECNET: Send "message not received" reply on reception of corrupted messages Values: 0 (No) # 1 (Yes) 1 SOS-EFFMSGNOK: Delete corrupted messages Values: 0 (No) # 1 (Yes) 1 SOS-PROMONET: Auto directory enrichment (Internet promotion) Values: 0 (No automatic enrichment of directory) #1 (automatic enrichment of directory enabled) 0 SOS-VIDEMBOX: Delete first message in the mailbox Values: # 0 (No) 1 (Systematically delete first document) 0 SOS-VIDEALLMBOX: Delete entire mailbox Values: # 0 (No) 1 (Systematically empty mailbox) 0 Rserv 1 SOS-PJTXT: Text attachment processing Values: 0 (No) #1 (Process text attachment) 5.3.11 SOFT-SWITCH 14 : INTRANET (MODEL LFF4) Value Description 0 SOS-CODNET: Document encoding type for Internet Comm. 0 Values: # 00 (MH encoding) 01 (MR encoding) 10 (MMR encoding) 0 Reserved 1 Reserved 0 Reserved 0 Reserved 0 Reserved 0 Reserved 5.3.12 SOFT-SWITCH 15 : INTRANET (MODEL LFF4) Value Description 1 Reserved 1 Reserved 1 Reserved 1 SOS-REPSMTP: Wait for 2 packets after HELO command in SMTP Values: # 0 (Normal, wait for single rely packet) 1 (Wait for a second packet if the first one is empty) 0 Reserved 0 Reserved 0 Reserved 1 Reserved
Bit 1 2 3 4 5 6 7 8 Bit 1 2 3 4 5 6 7 8
- 13 -
Bit 1 2 3 4 5 6 7 8 Bit 1 2 3 4 5 6 7 8
5.3.13 SOFT-SWITCH 16 : INTRANET (MODEL LFF4) Value Description 0 SOS-ACKNORECNET2: Send a "message not understood" reply on reception of TIFF attchment Values: # 0 (Send message) 1 (Do not send message) 0 SOS-MAILSWIMP: Printout when rerouting mailswitch Values: # 0 (Printout) 1 (No printout) 0 Reserved 0 Reserved 0 SOS-ACTREEM: Enable/disable rerouting Values: # 0 (Rerouting disabled) 1 (Rerouting/transfer enabled) 0 SOS-IMP-MAILTXT: Double printout of mail text in translation Values: # 0 (Double impression) 1 (Single printout but unlimited reception impossible) 0 Reserved 0 Reserved 5.3.14 SOFT-SWITCH 17 : INTRANET (MODEL LFF4) Value Description 1 Reserved 0 SOS - REPERTOIRE-IMPORT: Enable directory import by e-mail Values: # 0 (Unauthorised) 1 (Authorised) 0 Reserved 0 Reserved 0 Reserved 0 Reserved 0 SOS-IMP-AVISDEPOT: "Delivery notice" report printout 0 Values: # 00 (no) 01 (yes) 10 (systematically) 11 (only in case of error) 5.3.15 SOFT-SWITCH 18 : CODING / UART RATE Value Description 1 SOS-CODMEM : Stored document encoding type 1 Values : 00 (RL Coding) 01 (MH Coding) 10 (MR Coding) #11 (MMR Coding) 1 SOS-CODCOM : COM negociated encoding type 1 Values : 01 (MH Coding) 10 (MR Coding) #11 (MMR Coding) 0 Reserved 0 0 SOS-AFF_VIT_REELLE : Show/hide real communication rates Values : # 0 (show reduced rates) 1 (show real rates) 0 Reserved
Bit 1 2
3 4 5 6 7 8
- 14 -
Bit 1 2 3 4 5 6 7 8
5.3.16 SOFT-SWITCH 19 : MISCELLANEOUS SOFTWARE FUNCTIONS Value Description 0 Reserved 1 Reserved 0 SOS-GROUPE : Restriction on groups (or distribution list) Values : # 0 (No groups) 1 (Groups accepted) 0 SOS-REGULREC : T30 reception control inhibited Values : # 0 (Without) 1 (With) 0 Reserved 1 SOS-MENUCLAVIER : Hide keyboard menus and force QWERTY keyboard Values : 0 (Show) # 1 (Hide) 0 SOS-ONETOUCH : Enable "One touch" functions Values : # 0 (Without) 1 (With) 0 SOS-TLC : Accept software download via STN Values : # 0 (Without) 1 (With) 5.3.17 SOFT-SWITCH 21 : T4 DECODEUR / DEBUG Value Description 1 SOS-TRAITLIGERR : T4 decoding line copying mode Values : 0 (For each line with an error) # 1 (Only once, then destroy) 0 Reserved 0 Reserved 0 Reserved 1 SOS-GARBAGE-FLASH : Flash memory garbage collection method Values : 0 (garbage collection when application terminates) # 1 (garbage collection as background task) ATTENTION : taken into account only after reboot of the CPU 0 Reserved 0 SOS-DETECT OCCUP : Inhibition of engaged tone detect Values : # 0 (Without)1 (With) 0 Reserved 5.3.18 SOFT-SWITCH 22 : MISCELLANEOUS Value Description 0 SOS-DUREE-2100 : Transmission time of the 2100 modified for V34 recep0 tion Values : # 00 (5 seconds) 01 (4.5 seconds) 10 (4 seconds) 11 (3.5 seconds) 0 SOS-SORTIMP : Printing at the end of fax communications Values : # 0 (Printing during comm.) 1 (Print after comm.) 0 Reserved 0 SOS - WEB- ACCES: Access Mode to embedded Web server (model LFF4) Values: # 0 (Unprotected access) 1 (Password protected access) 0 SOS-AUTO-GDFID: Enable periodic self-identification (model LFF4) Values: # 0 (no)1 (Yes) 0 SOS-AUTO-GDFSTS: Enable status automatic transmission to the F@x manager (model LFF4) Values: # 0 (No)1 (Yes) 0 SOS-AUTO-GDFTLR: Enable remote readout automatic transmission to the F@x manager (model LFF4)
Bit 1 2 3 4 5
6 7 8 Bit 1 2
3 4 5 6 7
- 15 -
Bit 1 2 3 4 5
6 7 8
5.3.19 SOFT-SWITCH 23 : MISCELLANEOUS Value Description 1 SOS-JBIG : SUPER 3 capability to execute communication with JBIG encoding. Values : 0 (No SUPER G3) 1 (Negociated SUPER G3) 0 Reserved 0 SOS-FSI-NOCOVER : Inhibition of generation of cover pages. Values : # 0 (FSI V6 cover page) 1 (FSI V7 cover page) Only SAGEM 0 SOS-COMPACTE-RL : Compacting of run length (for fax server ELLIPSE) Values : # 0 (No compacting)1 (Compacting run length of no length) 0 SOS-DEBRIDAGE-JAUGE : Acceptation of EEPROM cards at any moment. Values : # 0 (No) 1 (Yes) Return to 0 after removing the card. 0 SOS-TLCNET: Download software from Internet/intranet (model LFF4) Values: # 0 (Download disabled) 1 (Download enabled) 0 SOS-POINT-FINAL-SEUL: Final DATA_SMTP point on its own in the TCP frame ("Peltex" problem) (model LFF4) Values: # 0 (Disabled)1 (Enabled) 1 SOS-PDF: Transmission and reception of PDF document via e-mail (model LFF4) Values : 0 (Disabled) 1 (Enabled) 5.3.20 SOFT-SWITCH 24 : SMS / IEEE ADRESS Value Description 1 SOS-AOP-IEEE: Modification of the IEEE address by the AOP (model LFF4) Values: # 0 (Modification impossible)1 (Modification possible) 0 SOS-FAXSWITCH : Activation of fax switch Values : # 0 (Without)1 (With) 0 SOS-SMS PROTOCOLE: Type of protocol for SMS V23 (model LFF4) Values: # 0 (protocol according to the country)1 (Protocole 1) 0 Reserved 0 Reserved 0 Reserved 0 Reserved 1 Reserved 5.3.21 SOFT-SWITCH 25 : MISCELLANEOUS (MODEL LFF4) Value Description 1 0 Reserved 0 0 0 Reserved
Bit 1 2 3 4 5 6 7 8 Bit 1 2 3 4 5
- 16 -
Bit 6
Value 0
7 8
0 1
Description SOS-TXADTERMINAL: Transmit the terminal address in the server number # 0: No 1: Yes Reserved SOS-EXPBITPDF: Export the attached file format field (Image/PDF) when exporting the directory via e-mail. # 0: No 1: Yes ATTENTION: If the directory is exported to a machine which does not support this format, the machine (receiver) will loose its current directory, and wont be able to restore the new one.
Bit 1 2 3 4 5 6 7 8 Bit 1 2 3 4 5 6 7 8
5.3.22 SOFT-SWITCH 26 : MISCELLANEOUS Value Description 0 Reserved 0 LOGIN authentification activation (model LFF4) #0: LOGIN authentification enabled 1: LOGIN authentification disabled 0 Reserved 0 Restriction on USB function Values : # 0 (Without)1 (With) 0 With or without duplication of on page passage threshold. Values : #0 : No duplication: NBI_SUP_B (1cm) 1 : Duplication: NBI_SUP_B * 2 (2 cm) 0 RR/RNR regulation limitation to 4 in T30. Values : #0 : No limitation 1 : With limitation 0 Double alternation optocoupler use Values : #0 : Optocoupleur mono alternation 1 : Optocoupleur double alternation 0 Rserv 5.3.23 SOFT-SWITCH 27 : MISCELLANEOUS Value Description 0 Size of remote readout serial number 0 #1000: 8 digits remote readout serial number 0 1111 : 15 digits remote readout serial number (only for EGT for now) 0 0 Waiting time before validation of unexpected modulation in comparison with 0 expected modulation. (~/driver/m_lucent/sms_m_dp2v/src/dpmain.c) 0 # 00 = 60 + 0*30 ms= 60 ms 0 01 = 60 + 1*30 ms = 90 ms 02 = 60 + 2*30 ms = 120 ms 03 = 60 + 3*30 ms = 150 ms 04 = 60 + 4*30 ms = 180 ms 05 = 60 + 5*30 ms = 210 ms 06 = 60 + 6*30 ms = 240 ms ...... 0F = 60 + 15*30 ms = 510 ms
- 17 -
Bit 1 2 3 4 5 6 7 8
5.3.24 SOFT-SWITCH 28 : SMS Value Description 0 Reserved 0 Reserved 0 Disable the 1 second timer before the hanging up #0 : Enabled 1 : Disabled 0 Reserved 0 Reserved 0 Reserved 0 Reserved 0 Recall protection #0 : Without 1 : With 5.3.25 SOFT-SWITCH 29 : MISCELLANEOUS Value Description 0 Reserved 0 Reserved 0 Reserved 0 Force the V29 modulation for 9600 and 7200 rates #0 : Enabled 1 : Disabled 0 Reserved 0 Reserved 0 Reserved 0 Reserved 5.3.26 SOFT-SWITCH 31 : MISCELLANEOUS Value Description 0 Reserved 0 Reserved 0 Reserved 0 Displaying the TRASH CAN consumable (in the 86 menu) Values : # 0 (Without) 1 (With) 0 Using the DHCP queries in ad-hoc WLAN mode Values : # 0 (With) 1 (Without DHCP-directly APIPA) 0 Reserved 0 Reserved 0 Reserved 5.3.27 SOFT-SWITCH 33 : MISCELLANEOUS Value Description 0 Reserved 0 Reserved 0 Reserved 1 Reserved 1 Demande de validation de la bonne impression des fax partir dun seuil Values : # 0 (Without) 1 (With) 1 Reserved 1 Reserved 1 Reserved
- 18 -
- 19 -
Set up the machine in STN download mode (key sequence MENU, *, 3). There is no confirmation and an alarm sounds (indicating that a special key sequence has been entered). On the Quadrige, set up a transmission in Express mode of the binary file that contains the software and start it. To do so: - Click on the <Envelope> icon: this opens the Express mode window; - Find the binary file in the appropriate directory and click on <Valider> (validate); - Enter the phone number of the fax to be downloaded in the first destinataire (address) field; - Click on <Emettre> (send): the transmission is effected when it reaches the top of the transmission queue. The Quadrige calls the fax. If the connection is made, the fax displays Tlchargement en cours (download in progress) and the comm. pictograph is displayed. The communication can take about 23 minutes for a software of about 2000 kbytes. At the normal end of the communication the machine should not reboot immediately. If this occurs, there are two possibilities: - The file is corrupted (wrong checksum) or the software is not compatible with the machine, and the machine reboots with the software that was already installed. Check the file and restart the procedure. - The communication has been interrupted. Check the number of the fax, skip step 1 and directly restart the communication. After approximately 40 seconds, the machine switches itself off, then switches on again. The PLEASE WAIT message is displayed. Check the software version and the soft checksum by typing MENU * V. Or check the software version and the miniboot checksum by typing MENU * B or soft modem MENU * M and fonts checksum MENU * F. 5.4.3 DOWNLOADING WITH THE MINIBOOT 5.4.3.3 Via the excutable TELUSB2 This procedure requires a standard PC running under Windows and equipped with the TELUSB2.exe (version 2.2.0.0) executable and a USB cable. Before you start, position the bit n 8 to 1 on the Soft-switch 1. 1 - Set the terminals On/Off switch to Off (position 0). 2 - Connect the terminal to the PC via the USB cable. 3 - Press the 4, 6 and 0 keys simultaneously and set the On/Off switch to On (position I). The terminal is switched on. The message USB DETECTED WAITING FOR DOWNLOAD is displayed and an alert sound is emitted. If the message WAITING FOR A USB LINK is displayed, check that the terminal is properly connected to the PC via the USB cable. 4 - Release the 4, 6 and 0 keys. 5 - Continue downloading from step 3 of the section 5.4.1.1. 5.4.3.4 Via the UDPATEDEVICE function of the COMPANION SUITE This procedure requires a standard PC running under Windows and equipped with the Companion Suite software and a USB cable. Before you start, position the bit n 8 to 1 on the Soft-switch 1. 1 - Set the terminals On/Off switch to Off (position 0). 2 - Connect the terminal to the PC via the USB cable.
- 20 -
3 - Press the 4, 6 and 2 keys simultaneously and set the On/Off switch to On (position I). The terminal is switched on. The message RECEIVING FILE is displayed and an alert sound is emitted. 4 - Release the 4, 6 and 2 keys. 5 - Continue downloading from step 1 of the section 5.4.1.2. 5.4.4 DOWNLOADING WITH THE MINIBOOT Before you start, position the bit n 8 to 1 on the Soft-switch 1. 1 - Press the 4, 6 and 0 keys simultaneously and set the On/Off switch to On (position I). 2 - Press on Stop then type* R (4, 6 and 0 keys pressed). The machine reboots, the miniboot detects that the 4, 6 and 0 keys are pressed and switches to download mode. The machine displays the Waiting for USB link message and beeps. 3 - Release the keys. 4 - Continue downloading following one of the procedures above. 5.4.5 DOWNLOADING VIA LOCAL NETWORK This procedure requires an Ethernet cable and a PC equipped with a LAN card and the Outlook express software. Create an Outlook Express account: - Launch Outlook Express. - In the Tools menu, select Accounts . The window Internet Accounts appears. - Click on the Add button and select Mail. - Type "toto" in the Display Name field and click on Next. - Type "toto@toto" in the Email Adress field and click on Next. - Type the address "169.254.0.1" in the Incoming Mail Server field and Outgoing Mail Server field and click on Next. - Type "toto" in the Account Name field and click on Next and Finish. Check the account connection: - Select the newly create account in the Internet accounts list and click on the Properties. - In the Connection tab, tick the Connect using my local area network (LAN) "Local Network" checkbox and click on OK. Connect the PC and the terminal to the Ethernet cable. Perform the downloading process following the steps bellow: - Modify the terminal IP adress following the steps bellow: - Go to the menu: , 2, 5, 3, 2 then OK. - Type 169 254 000 001 then OK and STOP. - Position the SOS Softswitch bit 8 at 1: , *, #, OK, 1, OK, STOP. - Switch to the download mode: , *, T. The machine displays the WAITING @ LOAD message. - Create a message (using Outlook Express) on the PC destinated to "toto@toto" and attach to it the file containing the software to download to the terminal . Send the message. The terminal LCD screen displays the TELELOADING message. At the end of download, the terminal reboots.
- 21 -
- Check that the download was successfull by typing the following sequence on the terminal keyboard: , *, V. The terminal display shows the software version and the checksum.
6. REMOTE READABOUT
Attention - BEFORE AND AFTER EACH INTERVENTION ON A MACHINE EQUIPPED WITH THE REMOTE READOUT OPTION, PERFORM A MANUAL TRANSMISSION OF THE REMOTE READOUT PARAMETERS TO THE SERVER CENTER, IF THE STATE OF THE MACHINE ALLOWS IT. All faxes are equipped with the Remote Readout option (locked). The option is unlocked by the installer or maintenance technician during the initial installation or during the intervention following the subscription of the contract (see 5.3.7 page 11). When intervening on these machines, it is very important to proceed with care, because the remote readout parameters are verified by the processing center in order to detect any anomalies, such as moving the machine, withdrawal, unintentional modification of the parameters, attempted fraud, etc. At each automatic transmission, the Remote Readout parameters are transmitted in the night to the Server center. A report of the transmission of these parameters is printed.
- 22 -
The remote readout using the threshold criterion can be triggered only once per consumable. Once the remote readout has been transmitted, the criterion will no longer be tested until the consumable has been replaced. The transmissions triggered by the two criteria (thresholds and day) are independent of each other. I.e., as soon as one of the criteria is met, the transmission is triggered, irrespective of the state of the other parameters. The transmission is immediate. It is also possible to force a transmission manually by means of the FONCTIONS VOLUES (advanced functions) menu (key sequence , 8, 7, 3).
- 23 -
Field T_DATE_SEUIL_JOURS T_INIT_NOIR T_CPT_NOIR T_SEUIL_NOIR T_DATE_SEUIL_NOIR T_DATE_CHG_NOIR T_INIT_OPC T_CPT_OPC T_SEUIL_OPC T_DATE_SEUIL_OPC T_DATE_CHG_OPC
Type 0x45 0x46 0x47 0x48 0x49 0x4a 0x5a 0x5b 0x5c 0x5d 0x5e
Char. / Num. char* long long long char* char* long long long char* char*
The values of the field Cause d'mission (TCAUSE_EMIS, reason for transmission) are the following: Interval days 2 Manual send 3 Toner 4 The initial values of the page counters for new consumables are: 1500 pages for the toner (T_INIT_NOIR)
- 24 -
6.4.2 REMOTE READABOUT REPORT For each transmission a remote readout report is printed. It contains all the data that have been transmitted to the server in transparent mode. In the case of a transmission in fax mode, the fax that is received is identical to this report. The report uses the presentation shown below: ** PARAMETRES DE TELERELEVE ** INFORMATIONS GENERALES Numro 23 millions Numro de srie Numro compte client Numro de version Numro Nom Centre serveur Nom de la personne responsable Socit Adresse Adresse Adresse Code postal Ville Pays Langue Tlphone : XXXXXXXXXXX : XXXXXXXX : XXXXXXXXXXX : XXXXXXXXX : XXXXXXXXXXXXXXX : XXXXXXXXXXXX : XXXXXXXXXXXXXXX : XXXXXXXXXXXXXXX : XXXXXXXXXXXXXXX : XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX : XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX : XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX : XXXXXXXXXXXXXXX : XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX : XXXXXXXXXXXXXXX : XXXXXXXXXXXXXXX : XXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
INFORMATIONS DE GESTION Statut de l'imprimante:Nombre de pages : XXXXX Intervalle jours: Intervalle jours : XXXX Prcdente tlrelve le JJ/MM/AA HH :MM - Nombre de pages = XXXXX Toner: Nombre estim de pages : XXXXXSeuil pages : XXXXX Prcdente tlrelve le JJ/MM/AA hh:mm (XXXX pages) Dernier renouvellement le JJ/MM/AA hh:mm
- 25 -
6.4.3 DESCRIPTION OF THE PARAMETERS The different fields shown in the report are described below General information (TNO_23MIL) : the 23M of the module managed by the server, entered by the installer; (TNO_SERIE) : the identification of the terminal, entered by the installer; (TNO_CLIENT) : the identification of the contract, entered by the installer; (TNO_VERSION) : generated automatically; (TINDICATIF) : the machine number, entered by the installer; (TIDENTIFIANT) : the machine name, entered by the installer;
(TNO_SERVEUR) : the phone number of the server center or of the fax, entered by the installer. Nom du responsable (TNOMRESP) : the name of the person responsible for the terminal, entered by the installer. (TSOCIETE): the name of the company who owns the terminal, entered by the installer. (TADRESSEL1, TADRESSEL2 et TADRESSEL3): postal adress of the terminal, entered by the installer. (TVILLE): entered by the installer. (TPAYS): entered by the installer. (TLANGUE): entered by the installer.
(TTELEPHONE): entered by the installer. Printer Status (T_CPT_PAGES): the cumulative total number of pages printed since the installation of the machine.
Interval in Days (T_CRIT_JOURS): the trigger interval using the day criterion (0 if the criterion is not active), entered by the installer; (T_DATE_SEUIL_JOURS): date of the last remote readout triggered by the day criterion, or installation date if there has not been any previous remote readout; (T_CPT_PAGES_JOURS): value of the cumulative number of pages printed at the date of the previous remote readout triggered by the day criterion (or 0 if there has not been any previous remote readout). Toner (T_INIT_NOIR): theoretical capacity of the cartridge estimated in average pages; (T_SEUIL_NOIR): trigger level (expressed as the number of pages remaining to be printed) for the transmission of a remote readout triggered by the toner threshold criterion, entered by the installer; (T_DATE_SEUIL_NOIR): date of the last remote readout triggered by the toner threshold criterion, or installation date if there has not been any previous remote readout; (T_CPT_NOIR): theoretical number of pages remaining to be printed at the instant of the triggering of the previous remote readout by the toner threshold criterion (or 0 if there has not been any previous remote readout);
- 26 -
(T_DATE_CHG_NOIR): date of the last replacement of the toner cartridge. Transmission Data (TCAUSE_EMIS): reason for the remote readout transmission; Heure mission (TDATE_EMIS): date of the transmission of the remote readout.
6.5
REMINDERS
Every fax is equipped with a copy counter, implemented in EEPROM memory on the CPU board. This counter is used in particular by the Remote Readout function. It can be consulted by the user (see 5 of the Installation Guide). This counter cannot be modified. It is stored indefenitely. Before any corrective intervention on the machine that risks modifying the installation parameters or the value of the counter (replacement of the CPU board or installation of new software), a manual Remote Readout transmission should be performed, if the state of the machine allows it. If this transmission is not possible for any reason, print out the Remote Readout parameters or display the copy counter and note these values on the intervention report.
- 27 -
Phone cord
CDRom containing the User Guide (UG) and the Companion Suite software
5 - Pack all documentation (manuals and printed documents) into the packing box and seal it with adhesive tape.
-1-
MAINTENANCE GUIDE
CONTENTS
1 SCANNER AND COMMUNICATION 1.1 PREVENTIVE MAINTENANCE 1.1.1 Paper transport rollers 1.1.2 Paper separator module 1.1.3 CIS and Flatbed window 1.1.4 Front panel keys and covers SCANNING AND COMMUNICATION ERROR CODES 1.2.1 Communication Error Codes 1.2.2 General Codes 3 3 3 3 4 4 5 5 5
1.2
1.3
7 MAINTENANCE-TUNING 1.3.1 Supply voltages: connections between the power supply board and CPU board 7 1.3.2 Checking the quality of prints and tuning the scanner 7 DISASSEMBLY/ASSEMBLY WORKSHEETS 1.4.1 List of tools 1.4.2 List of worksheets 1.4.3 Worksheet chart ADMINISTRATOR FUNCTIONS 1.5.1 Initializing and erasing memory 1.5.2 Other functions REPLACING THE CPU BOARD REPLACING THE SCANNER 8 8 8 9 40 40 41 42 42 43 43
1.4
1.5
1.6 1.7
-2-
-3-
1 - Set the On/Off switch to Off (position 0). 2 - Open the ADF scanner cover. 3 - Clean the rollers of the document feeder and feed shafts, and also the two idler rollers located on the mobile part of the scanner, with a lint-free cloth moistened in isopropyl alcohol. To clean them, rotate them in the same direction as during paper transport. Recommended interval: from 2 to 6 months, depending on utilization. 1.1.2 PAPER SEPARATOR MODULE
-4-
2 - Open the ADF scanner cover. 3 - Disassemble the ADF feeder (see Worksheet D4, page 17). 4 - Wipe the elements of the paper separator module with a lint-free cloth soaked with isopropyl alcohol. Recommended interval: from 2 to 6 months, depending on utilization. 1.1.3 CIS AND FLATBED WINDOW 1 - Set the On/Off switch to Off (position 0). 2 - Open the flatbed scanner cover. 3 - Clean the CIS window with a lint-free cloth moistened with isopropyl alcohol or use antistatic paper used for cleaning optic glass. Recommended interval: depending on utilization; it is advisable to make a local copy to check if the window is clean. 1.1.4 FRONT PANEL KEYS AND COVERS 1.1.4.1 Cleaning the front panel keys 1 - Set the On/off switch to Off (position O). 2 - Clean the top of the front panel and the keys with a lint-free cloth moistened with isopropyl alcohol or a spray-on cleaning product. 3 - Leave the product on for a few seconds before wiping it off. Recommended interval: to be defined depending on utilization. 1.1.4.2 Cleaning the covers It is advisable to clean all the covers during a maintenance visit. 1 - Set the On/Off switch to Off (position O). 2 - Clean the external areas of the covers with a lint-free cloth moistened with isopropyl alcohol or a spray-on cleaning product. 3 - Leave the product on for a few seconds before wiping it off.
-5-
07 08
Disconnect Quality
parameter is set to WITHOUT PAPER. The communication has been cut (bad connection). The document that you have transmitted has not been received correctly.
0A
No document to recover
You have attempted to recover a document from a correspondent, but the latter has not prepared (stored) the document or the password that was entered is wrong.
0B
There is a difference between the number of pages indicated when the document was prepared for transmission and the number of pages actually transmitted.
Check the called number. Contact your correspondent to check whether it is necessary to retransmit the document: the interference may have occurred in an unimportant area of the document. Contact your correspondent to check whether the document to recover has been prepared or to check the validity of the password. Check the number of pages of the document.
-6-
0D
13
14 15
16
17
18
19
1A
1B
50
Action Ask the correspondent to check/reduce the length of his document. Document transmission fault Document reception error. Ask the correspondent to retransmit his document. Memory full The terminal memory is full (there are Print the received documents. too many documents that have been received but not yet printed, or waiting Delete or transmit in immediate mode the to be transmitted). documents waiting to be transmitted. Memory full Received document memory saturated. Print the received documents. Mailbox number x unknown Failure to deposit a document in your Check the mailbox number of your correspondent mailbox (the mailbox correspondent. with this number does not exist with this correspondent). List number x not retransmit- Failure to retransmit a document via a Check that the list of ted remote fax (the requested list of recipi- recipients is ents is not programmed on the remote programmed on the remote fax. fax). Mailbox number x unknown Failure to recover a document in your Check the mailbox number of your correspondent mailbox (the mailbox correspondent. with this number does not exist with this correspondent). Retransmission impossible Failure to retransmit a document via a remote fax (the remote fax does have a retransmit function). Stopped by correspondent Communication stopped by your correspondent (Example: a fax attempts to recover a document from your fax, while there is no document waiting for this correspondent). Disconnect Transmission has not started (the Check the quality of the phone line is too noisy). phone line or restart the transmission at a later time. Document transmission fault Document transmission error. Transmission: restart the transmission. Reception: ask your correspondent to retransmit the document. Check the parameteriServer Error Invalid parameterized SMS server zed SMS server number number or a communication error and/or restart occured during data transfer. transmission.
-7-
1.3 MAINTENANCE-TUNING
1.3.1 SUPPLY VOLTAGES: CONNECTIONS BETWEEN THE POWER SUPPLY BOARD AND CPU BOARD CPU board pin Values Function CN 8-9 +5V 5V Supply 10-11 GND Ground 12-13 + 24 V 24V Supply Remark(s) : The mains input of the power supply is protected by a fuse. 1.3.2 CHECKING THE QUALITY OF PRINTS AND TUNING THE SCANNER To check or improve the quality of prints, you should first tune the scanner. Follow this procedure: 1 - Place a blank A4 sheet of paper in the loading tray of the ADF scanner. 2 - Press , enter * then A on the keyboard and confirm with OK. The terminal reboots. 3 - Start making copies of documents on the CIS window of the flatbed scanner and check the quality of the copies. If the problem persists and if it is related to the scanner: Repeat the tuning procedure (step 1). If the problem persists and if it is related to the printer (the scanner still provides unsatisfactory results): 1 - Press then enter 54 on the keyboard. The terminal prints the list of printer tunings. 2 - Check the printers printing and copying parameters. 3 - Check the consumable.
-8-
-9-
- 10 -
D1
Requirements None. Preliminary steps None. 1 - Stand in front of the terminal. 2 - Unlock the three clips of the front panel (A, B and C). Disassembly
3 - Push the panel towards the back to release it from the two bottom slots (D and E). 4 - Disconnect the panel ribbon cable from the panel card connector.
5 - Disassemble the equiped front panel. Assembly 1 - Unpack and check all new components. 2 - Connect the panel ribbon cable to the panel card connector. 3 - Position the panel by inserting the two lower bearings (D and E) into their slots then clip the upper part into place.
- 11 -
D2
Requirements Flat screwdriver (medium size). Cross-threaded (Philips) screwdriver. Preliminary steps None. White panel 1 - Stand in front of the terminal and open the ADF scanner cover. 2 - Pull out the white panel located inside the ADF scanner cover. Disassembly
ADF scanner cover 1 - Close the ADF scanner cover and open the ADF cover assembly.
2 - Remove the ADF motor cover from its two slots using a flat screwdriver then disassemble the ADF motor cover.
- 12 -
D2
4 - Disconnect the ADF scanner cover sensor connector (A) and the paper sensor connector (B).
5 - Open the ADF scanner cover, unscrew the two mounting screws of the cable cover and remove the cable cover.
6 - Remove the ground cable, the ADF cover sensor connector and the paper sensor connector from their cable guide then slide them out of the ADF scanner cover.
- 13 -
D2
7 - Insert a flat screwdriver in each slot of the two ADF scanner cover hinges.
8 - Lift and remove the ADF scanner cover, do not forget the mounting screws of the hinges.
Assembly 1 - Unpack and check all new components. 2 - Screw the mouting screws of the two hinges and position the ADF scanner cover by inserting the two hinges in their slots. 3 - Insert the ground cable, the ADF cover sensor cable and the paper sensor cable in the cable guide.
- 14 -
D2
4 - Position the cable cover, screw the two mouting screws then close the ADF scanner cover.
5 - Connect the paper sensor connector (black end) and the ADF cover sensor connector (white end).
ADF cover sensor 6 - Screw the mouting screw of the ground cable.
Paper sensor
7 - Clip the ADF motor cover in its slots and close the ADF feeder cover. 8 - Stick the white panel inside the ADF scanner cover.
- 15 -
D3
Preliminary steps None. Disassembly Printer front door 1 - Stand in front of the terminal. 2 - Push the left and right side of the printer front door and simultaneously pull it towards yourself. 3 - Move the arms away from each other and remove the printer front door.
Side covers 1 - Open the printers paper tray. 2 - Unscrew the two mounting screws on the front and back of the side covers.
- 16 -
D3
3 - Using a flat screwdriver, unscrew the side covers from their slots located under the terminal.
4 - Unclip the side covers from the top slots located at the back of the terminal and pivot them towards yourself to remove them.
5 -Remove the side covers. Assembly 1 - Unpack and check all new components. 2 - Assemble the covers, in first put the front part of the cover then the back part. 3 - Assemble the printer front door by reversing the steps for the disassembly procedure.
- 17 -
D4
Requirements Cross-threaded (Philips) screwdriver. Flat screwdriver. Preliminary steps None. Feeder assembly Disassembly 1 - Open the ADF cover.
3 - Lift the roller bearing from the other end of the feeder.
- 18 -
D4
4 - Lift the feeder and remove the feeder. Assembly 1 - Unpack and check all new components. 2 - Position the feeder in its slot, positionning correctly the teeth gear in the motor assembly. 3 - Lower the two roller bearings. LFX Rocking plate and cork Preliminary steps Disassemble the feeder aseembly. Disassembly Rocking plate 1 - Insert a screwdriver in the right slot as shown below and make a pivoting movement downwards without strain to remove the rocking plate. 2 - Repeat the previous step for the left slot of the rocking plate.
3 - Remove the feeder shoe, the rocking plate and the rocking lever spring. LFX Cork 1 - From the upper part of the ADF scanner. 2 - Insert a screwdriver in the right slot as shown below and make a pivoting movement downwards without strain to remove the LFX cork.
- 19 -
D4
Assembly LFX Cork 1 - Make sure that the slot of the cork on the paper input guide is clean. 2 - Unpack and check all new components. 3 - Remove the adhesive from the cork and place the cork in its slot. Rocking plate 1 - Unpack and check all new components. 2 - Equip the rocking plate with the rocking lever spring. 3 - Position the assembly in its slot. 4 - Place the feeder shoe on the rocking plate respecting the assembly structure then press on the right and left sides until it reaches its final position. Inside paper way assembly Preliminary steps None. Disassembly 1 - Lift the ADF cover and unscrew the two mouting screws of the inside paper way assembly.
2 - Lift the inside paper way assembly and remove it from its slot without disassembling it.
- 20 -
D4
4 - Disconnect the connector reaching the ADF cover and remove the inside paper way assembly.
Assembly 1 - Unpack and check all new components. 2 - Position the inside paper way assembly near its final slot. 3 - Connect the motor frame connector to its connector. 4 - Hold the inside paper way assembly, open the ADF cover. Screw the two mounting screws. Upper paper guide assembly Preliminary steps Disassemble the feeder assembly. Disassembly 1 - Open the ADF cover.
- 21 -
D4
Assembly 1 - Unpack and check all new components. 2 - Insert the paper guide assembly forward in the paper input guide. 3 - Screw the two mounting screws.
Motor frame Preliminary steps Disassemble the inside paper way assembly.
- 22 -
D4
2 - Lift and remove the motor frame. Locate the teeth gears and remove them.
Motor Disassembly 1 - Unscrew the two mounting screws of the motor and remove the motor.
Assembly 1 - Position the motor on its frame and screw the two mounting screws.
- 23 -
D4
Motor frame assembly 1 - Unpack and check all new components. 2 - Position the teeth gears respecting their location identified during disassembly.
3 - Position the equiped motor frame in its slot on the inside paper way assembly.
4 - Screw the mounting screw of the motor frame. White frame plate / Analysis roller / Brosse antistatique / ADF Sliders Preliminary steps Disassemble the inside paper way assembly and motor frame for analysis rollers. White frame plate disassembly 1 - Turn the inside paper way assembly upside down.
- 24 -
D4
2 - Lift the white frame plate to disassemble it from the inside paper way assembly and remove it.
- 25 -
D4
White frame plate assembly 1 - Unpack and check all new components. 2 - Position the white frame plate on the inside paper way assembly and press on the white frame plate to clip it on the inside paper way assembly. Analysis roller assembly 1 - Turn the inside paper way assembly upside down. 2 - Turn the roller bearing turning of each one of the analysis rollers.
3 - Remove the roller bearing turnings of the analysis rollers and remove the rollers. Analysis roller assembly 1 - Unpack and check all new components. 2 - Position the analysis rollers in their slots. 3 - Position the roller bearing turnings on the ends of the analysis rollers and fix them with the roller bearing turnings. ADF sliders and brosse antistatique disassembly 1 - Turn the inside paper way assembly upside down. 2 - Unscrew the two mounting screws of the ADFwheelbox and remove it.
- 26 -
D4
3 - Lift vertically the ADF sliders and remove them from the inside paper way assembly.
ADF sliders and brosse antistatique assembly 1 - Unpack and check all new components. 2 - Check that the slot of the brosse antistatique is clean. 3 - Position the brosse antistatique in its slot and press on the lower part to make sure the adhesives are strongly fixed. 4 - Position the ADF sliders in their slots. 5 - Position the ADF wheelbox on the inside paper way assembly. 6 - Screw the two mounting screws.
- 27 -
D5
Requirements Cross-threaded (Philips) screwdriver. Preliminary steps Disassembling the printer front door and the right side cover (see worksheet D3). Disassembly 1 - Unscrew the three mounting screws of the CPU board armour plate.
2 - Pull the CPU board armour plate towards yourself and remove it. 3 - Unscrew the mounting screw of the CPU card ground connector and disconnect it.
4 - Disconnect all incoming cords and leads from the CPU module connectors. Attention - MEMORIZE ALL CONNECTIONS FOR REASSEMBLY.
- 28 -
D5
5 - Unscrew the eight mounting screws and remove the CPU board.
Assembly 1 - Unpack and check all new components. 2 - Place the CPU board in the rack, screw in and tighten the eight mounting screws. 3 - Connect all the cords and leads to their corresponding CPU board connectors. 4 - Position and screw the ground connector to the CPU card. 5 - Position the CPU board armour plate, screw and tighten the three mounting screws. 6 - Position the right-hand side cover and the front door. (see Worksheet D3).
- 29 -
D6
Requirements None. Preliminary steps Disassembling the front door and the right-hand side cover (see Worksheet D3). Disassembling the CPU armour plate (see Worksheet D5). Disassembly 1 - Disconnect the loudspeaker connector from the CPU board. 2 - Remove the loudspeaker connector from its ferrite tube and cable guide.
Attention - MEMORIZE THE CABLE GUIDE FOR REASSEMBLY. 3 - Press the top clip inwards until it unclips and pull the loudspeaker towards yourself.
4 - Disassemble the loudspeaker. Assembly 1 - Unpack and check all new components. 2 - Position the loudspeaker in front of its slot and insert the lower part. 3 - Press the top part of the loudspeaker until it clicks into place. 4 - Place the loudspeaker connector into its cable guide, do not forget the ferrite tube. 5 - Connect the loudspeaker connector to the CPU board. 6 - Put the CPU board armour plate into place (see Worksheet D5). 7 - Put the right-hand side cover and the front door into place (see Worksheet D3).
- 30 -
D7
Requirements Cross-threaded (Philips) screwdriver. Flat screwdriver. Preliminary steps Disassemble the flatbed scanner cover (see Worksheet D2). Disassemble the front door and the side covers (see Worksheet D3). Disassemble the CPU board armour plate (see Worksheet D5). Disassembly 1 - Disconnect the scanner connector from the CPU board and remove it from its ferrite tube and cable guide. 2 - Disconnect the front panel ribbon cable and the CIS ribbon cable from the CPU board.
Attention - MEMORIZE THE CONNECTIONS FOR REASSEMBLY. 3 - Remove the front panel and CIS ribbon cables from their cable guide.
- 31 -
D7
4 - Unlock the assembled flatbed scanner with a flat screwdriver and pull it towards yourself.
Assembly 1 - Unpack and check all new components. 2 - Stand in front of the terminal. 3 - Position the assembled flatbed scanner on the equiped printer and slide it towards the left until it clicks into place. 4 - Place the front panel and CIS ribbon cables into their cable guide. 5 - Connect the front panel and CIS ribbon cables to the CPU board. 6 - Connect the scanner connector to the CPU board, do not forget the ferrite tube. 7 - Position the CPU board armour plate (see Worksheet D5). 8 - Position the side covers and the printer front door (see Worksheet D3). 9 - Position the ADF scanner cover (see Worksheet D2).
- 32 -
D8
OBJECT :EQUIPED SCANNER - SCANNER WINDOW FRAME - CIS - CIS RIBBON CABLE - CIS SUPPORT - SCANNER MOTOR
Requirements Cross-threaded (Philips) screwdriver. Flat screwdriver. Preliminary steps Disassemble the scanner cover (see Worksheet D2). Disassemble the printer front door and the side covers (see Worksheet D3). Disassemble the CPU board armour plate (see Worksheet D5). Disassemble the assembled flatbed scanner (see Worksheet D7). Disassembly Scanner window frame 1 - Unscrew the two mounting screws on the equiped scanner (A and B) and turn it upside down.
2 - Unscrew the seven mounting screws at the back of the equiped scanner and turn it upside down.
- 33 -
D8
OBJECT :EQUIPED SCANNER - SCANNER WINDOW FRAME - CIS - CIS RIBBON CABLE - CIS SUPPORT - SCANNER MOTOR (CONTI3 - Lift the front part of the scanner window panel and disassemble it.
2 - Disconnect the CIS ribbon cable and disassemble it from its two side slots. Attention - KEEP THE CIS SUPPORT SPRINGS AND SLIDES.
- 34 -
D8
OBJECT :EQUIPED SCANNER - SCANNER WINDOW FRAME - CIS - CIS RIBBON CABLE - CIS SUPPORT - SCANNER MOTOR (CONTI CIS ribbon cable 1 - Unfold the end of the CIS ribbon cable and remove it from its slot.
2 - Slide the CIS ribbon cable out of its ferrite tube which is fixed to the CIS panel and remove it from the scanner. 3 - Remove the CIS ribbon cable from its cable guides located above and below the scanner bottom then slide it to extract it from the scanner bottom. Attention - MEMORIZE THE CABLE GUIDE FOR REASSEMBLY. 4 - Disasssemble the CIS ribbon cable. CIS support 1 - Lift the CIS drive pulley and the drive to extract the CIS drive pulley from its slot.
- 35 -
D8
OBJECT :EQUIPED SCANNER - SCANNER WINDOW FRAME - CIS - CIS RIBBON CABLE - CIS SUPPORT - SCANNER MOTOR (CONTI Scanner motor 1 - Unscrew the two mounting screws of the scanner motor (A et B).
2 - Remove the end of the scanner motor connector from its ferrite tube. 3 - Remove the CIS motor connector from its cable guide.
4 - Disassemble the scanner motor. Assembly 1 - Unpack and check all new components. 2 - Position the scanner motor and screw in the two mounting screws. 3 - Place the motor connector into it cable guide, without forgetting the ferrite tube. 4 - Position the CIS support, place the belt in the CIS drive pulley, do not forget the CIS support springs. 5 - Check that there is enough grease on the pulley motor axis. 6 - Place the CIS ribbon cable in its cable guide, do not foget the ferrite tube, then connect it to the CIS. 7 - Place the CIS, do not forget its slides and support springs. 8 - Position the scanner window frame by first inserting the back part, then insert the front part. Screw in the two mounting screws for the scanner window frame. 9 - Turn the equiped scanner around and screw in the seven mounting screws. 10 - Assemble the assembled flatbed scanner (see Worksheet D7). 11 - Assemble the CPU board armour plate (see Worksheet D5).
- 36 -
D8
OBJECT :EQUIPED SCANNER - SCANNER WINDOW FRAME - CIS - CIS RIBBON CABLE - CIS SUPPORT - SCANNER MOTOR (CONTI12 - Assemble the side covers and the printer front door (see Worksheet D3). 13 - Assemble the ADF scanner cover (see Worksheet D2).
- 37 -
D9
Requirements Cross-threaded (Philips) screwdriver. Preliminary steps Disassemble the ADF scanner cover (see Worksheet D2). Disassemble the printer front door and the side covers (see Worksheet D3). Disassemble the CPU board armour plate (see Worksheet D5). Disassemble the assembled flatbed scanner (see Worksheet D7). Disassembly 1 - Stand behind the terminal. 2 - Unscrew the two back mounting screws on the back cover (A et B).
3 - Unscrew the two top mounting screws on the back cover (C et D).
4 - Pull the back cover towards yourself and remove it. Assembly 1 - Unpack and check all new components. 2 - Place the back cover and screw in the four mounting screws (A, B, C et D). 3 - Assemble the assembled flatbed scanner (see Worksheet D7). 4 - Assemble the CPU board armour plate (see Worksheet D5). 5 - Assemble the printer front door and the side covers (see Worksheet D3). 6 - Assemble the ADF scanner cover (see Worksheet D2).
- 38 -
D10
Requirements Cross-threaded (Philips) screwdriver.. Preliminary steps Disassemble theADF scanner cover (see Worksheet D2). Disassemble the printer front door and the side covers (see Worksheet D3). Disassemble the CPU board armour plate (see Worksheet D5). Disassemble the loudspeaker (see Worksheet D6). Disassemble the assembled flatbed scanner (see Worksheet D7). Disassemble the back cover (see Worksheet D9). Disassembly 1 - Unscrew the two mounting screws on the left and right side on the equiped interface.
Assembly 1 - Unpack and check all new components. 2 - Position the equiped interface and screw in the four mounting screws on both sides. 3 - Assemble the back cover (see Worksheet D9). 4 - Assemble the assembled flatbed scanner (see Worksheet D7). 5 - Assemble the loudspeaker (see Worksheet D6). 6 - Assemble the CPU board armour plate (see Worksheet D5). 7 - Assemble the printer front door and the side covers (see Worksheet D3). 8 - Assemble the ADF scanner cover (see Worksheet D2).
- 39 -
D11
OBJECT :PRINTER
Requirements Cross-threaded (Philips) screwdriver. Preliminary steps None. Disassembly 1 - Stand in front of the terminal. 2 - Disassemble the equiped front panel (see Worksheet D1) and the ADF scanner cover (see Worksheet D2). 3 - Disassemble the printer front door and the side covers (see Worksheet D3). 4 - Disassemble the CPU module (see Worksheet D5) and the loudspeaker (see Worksheet D6). 5 - Disassemble the assembled flatbed scanner (see Worksheet D7). 6 - Disassemble the back cover (see Worksheet D9) and the equiped interface (see Worksheet D10). Assembly 1 - Unpack and check all new components. 2 - Assemble the equiped interface (see Worksheet D10) and the back cover (see Worksheet D9). 3 - Assemble the flatbed scanner assembly (see Worksheet D7). 4 - Assemble the CPU module (see Worksheet D5) and the loudspeaker (see Worksheet D6). 5 - Assemble the side covers and the printer front door (see Worksheet D3). 6 - Assemble the ADF scanner cover (see Worksheet D2) and the equiped front panel (see Worksheet D1).
Flatbed
Loudspeaker
- 40 -
and
To see the initialization message (this requires inserting the smart card INIT), switch On then Off. Reinitialize the flash data (erases all):open the printer front door then :
#
5
- 41 -
Then switch ON/OFF the machine. 1.5.2 OTHER FUNCTIONS Before you start, position the Soft-switch 1 bit n8 to 1. Printing all parameters (including installation and technical parameters):
*
1
- 42 -
* R):
- 43 -
1 - Print the terminals parameters (user, administrator and technical) and the activity counter values in order to keep a record ( 5 4). 2 - Replace the scanner (see Worksheet D7). 3 - Tune the scanner ( 8 0) only if the quality of the copy is unsatisfactory.
2. LASER PRINTER
Refer to the printers technical manual.
-1-
-2-
PLANCHE 10 / FIGURE 10 Registre papier Paper regist PLANCHE 11 / FIGURE 11 Unit de fusion Fusing unit PLANCHE 12 / FIGURE 12 Parties lectriques Electric parts
25 26 27 28 29 30
-3-
1. 1.1
1.2
Il est galement ncessaire de mentionner la rfrence du document dans lequel le numro de code a t trouv. Les commandes de pices de rechange et la correspondance sy rapportant (demandes de prix, dtails de livraison, facturation, etc.) sont formuler : SAGEM Communication Dpartement Service Clients 27, rue Leblanc 75512 PARIS CEDEX 15 - FRANCE Tel : +33 (0)1 40 70 63 63 Fax : +33 (0)1 40 70 84 73 http://www.sagem.com Dans les cas durgence, les demandes de rechange peuvent tre formules par tlphone ou de prfrence par minitel ou par tlcopie au numro ci-dessus.
-4-
2. 2.1
2.2
It is also recommended to state the reference of the document in which the part number has been found. Orders for spare parts and related correspondence (requests for prices, delivery details, invoicing, etc.) are to be addressed to: SAGEM Communication Dpartement Service Clients 27, rue Leblanc 75512 PARIS CEDEX 15 - FRANCE Tel : +33 (0)1 40 70 63 63 Fax : +33 (0)1 40 70 84 73 http://www.sagem.com In emergencies, spare part orders may be communicated by telephone or, preferably, in the form of a fax to the above address.
-5-
3 4
PLANCHE 1 / FIGURE 1
-6-
ITEM No. 1 2 3 4
REFERENCE Voir 3 See 3 Voir 3 See 3 Voir 3 See 3 Voir 3 See 3 Plastron Front panel
DESIGNATION
QTY 1 1 1 1
Terrminal de base (voir planche 2) Terrminal basic assembly (see figure 2) Cordon dalimentation secteur AC Power cord Cordon ligne tlphonique Telephone line cord
PLANCHE 1 / FIGURE 1
-7-
14
5 6
13 12 11 10 9 8
PLANCHE 2 / FIGURE 2
-8-
ITEM No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14
REFERENCE 252296672 252469770 252306671 252306663 188616956 252237243 185588072 252237214 252106802 Voir 3 See 3 189372756 252201206 252237222 252366651
DESIGNATION Flap quip (voir planche 7) Flap equiped (see figure 7) ADF doc tray D7N color ADF doc tray D7N colored Scanner plat assembl (voir planche 5) Flat bed scanner assembly (see figure 5) Imprimante quipe (voir planche 3) Equiped printer (see figure 3) Vis M3X6 steel swch16A Screw 3X6 Haut-parleur Loud speaker Tube ferrite Ferrite sensor wires and motor wires Capot latral droit color Right printer cover colored Tle de blindage carte UC Bracket ctl a v Carte UC Terrminal Terrminal Main PCB board Serre cbles Twist-lok nylon Serre cbles Twist-lok nylon Porte faade avant imprimante assembl Printer front door assembly Capot latral gauche color Left printer cover colored Support pupitre assembl Front panel support assy
QTY 1 1 1 1 15 1 1 1 1 1 1 1 1 1
PLANCHE 2 / FIGURE 2
-9-
1 8 3 4 2
PLANCHE 3 / FIGURE 3
- 10 -
ITEM No. 1 2 3 4 5 6 7 8
DESIGNATION Guide papier sortie imprimante Printer exit paper guide Vis RLX 3-10 AC.ZN.Blanc p.plast PT screw M3*10 Capot arrire imprimante color Printer back cover colored Trappe arrire Cover rear Imprimante Printer Tirette imprimante + extension Tray exit+ extend Interface quipe (voir planche 4) Interface equiped (see figure 4) Vis autar. M3x6 steel swch16A Screw autar. M3x6 steel swch16A
QTY 2 2 1 1 1 1 1 6
PLANCHE 3 / FIGURE 3
- 11 -
Vue de dessous
PLANCHE 4 / FIGURE 4
- 12 -
ITEM No. 1 2 3 4
DESIGNATION Vis RLX 3-10 AC.ZN.Blanc p.plast PT screw M3*10 Brosse antistatique Discharge brush Interface colore Interface colored Ferrite p.cable plat 3W800 10 cond. Ferrite flat cable CIS 12 pin
QTY 2 1 1 1
PLANCHE 4 / FIGURE 4
- 13 -
17 16 15 18
3 4
14 13 12 11 10 9
PLANCHE 5 / FIGURE 5
- 14 -
ITEM No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
REFERENCE 189393578 252293770 187956942 252325093 252197288 252236874 252236978 252236949 252236895 252236957 252236915 252236960 252151823 252151815 252236824 189061931 252236832 252152528
DESIGNATION Vis RLX 3-10 AC ZN Blanc P.Plast PT screw 3x10 Support vitre scanner plat assembl Scanner frame assembly Ferrite p.cable plat 3W800 10 cond. Ferrite flat cable CIS 12 pin Adhsif double face ferrite CIS ferrite & flat cable D-tape 13mm Support CIS (voir planche 6) CIS support (see figure 6) Poulie renvoi courroie CIS colore CIS drive pulley colored Nappe console 16 points Console cord 16 pin Fond scanner color Scanner bottom colored Pignon 55 dents scanner plat color Scanner gear 55 teeth colored Disque pignon 15-55 dents color CIS drive disc colored Pignon 32/70 dents scanner plat color Scanner gear 32/70 teeth colored Interface support moteur colore CIS drive adaptador colored Tle moteur scanner plat CIS drive heat sink Moteur scanner plat Stepper motor scanner Glissire CIS gauche colore CIS slider left colored CIS DL515 sp CIS DL515 sp Glissire CIS droite colore CIS slider right colored Ressort CIS CIS spring
QTY 14 1 1 3 1 1 1 1 1 1 1 1 1 1 1 1 1 2
PLANCHE 5 / FIGURE 5
- 15 -
7 6
PLANCHE 6 / FIGURE 6
- 16 -
ITEM No. 1 2 3 4 5 6 7 8
DESIGNATION Nappe CIS flap 12 points CIS flap cable 12 pin Ferrite p.cbl.plat 3W800 10 cond. Ferrite flat cable CIS 12 pin Guidage central chariot CIS color CIS central roller colored CIS support color CIS support colored Guidage latral chariot CIS color CIS lateral roller colored Connecteur courroie CIS CIS drive belt connection Ressort courroie CIS belt spring Courroie CIS drive belt
QTY 1 1 2 1 3 1 1 1
PLANCHE 6 / FIGURE 6
- 17 -
PLANCHE 7 / FIGURE 7
- 18 -
ITEM No. 1 2 3 4 5 6
DESIGNATION Capot ADF assembl ADF cover assembly Capot moteur color Motor cover colored Chemin papier interne assembl (voir planche 8) Inside paper way assembly (see figure 8) Flap assembl Flap assembly Vis autotartte large pour plast. 3x8 3x8 self tap. screw large for head plas Cble moteur ADF et capteur ADF motor and sensors wires
QTY 1 1 1 1 2 1
PLANCHE 7 / FIGURE 7
- 19 -
3 4 22 23 5 4 23 21
7 20 19
13 24
9 15 3 12
11
10
PLANCHE 8 / FIGURE 8
- 20 -
ITEM No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
REFERENCE 252470046 252470038 252470017 188618129 252293717 252876321 252364959 252364970 252280533 187872675 252248192 252365224 252470025 251473155 251280779 251473189 252365245 252293759
DESIGNATION ADF slider left D7N color ADF slider left D7N colored ADF slider right D7N color ADF slider right D7N colored Palier quart de tour rouleau color roller bearing turning colored Vis autotartte large pour plast. 3X8 3X8 self tap.screw large for head plas Guide papier suprieur assembl Upper paper guide assembly Kit dliasseur ADF assembly kit Guide introduction papier color Paper input guide colored Chassis blanc color White frame plate colored Ressort palette blanche White frame plate spring Brosse antistatique auto adhsive 225mm Brosse antistatique auto adhsive 225mm Reprise de masse balayette Brush ground plate Pignon bac papier color Gear doc tray colored ADF wheelbox D7N color ADF wheelbox D7N colored Palier rouleau analyse color Analyse roller bearing colored Rouleau analyse Analysis roller Pignon 38 dents color 38 teeth analysis roller gear colored Pignon 27-33 dents color 27-33 teeth gear colored Support moteur assembl Motor frame assembly
QTY 1 1 3 6 1 1 1 1 2 1 1 1 1 2 1 2 1 1
PLANCHE 8 / FIGURE 8
- 21 -
ITEM No. 19 20 21 22 23 24
DESIGNATION Pignon 16-51 dents color 16-51 teeth gear colored Pignon 42 dents color 42 teeth gear colored Photo interrupter opic GP1A73A sp Photo interrupter opic GP1A73A sp Chargeur assembl Feeder assembly Rondelle M3x0,6 acier zingue Rondelle M3x0,6 acier zingue Rouleau analyse assembl avec mousse Analysis roller assy with foam
QTY 1 2 2 1 1 1
PLANCHE 8 / FIGURE 8
- 22 -
- 23 -
PLANCHE 9 / FIGURE 9
- 24 -
ITEM No. 1
DESIGNATION
QTY 1
PLANCHE 9 / FIGURE 9
- 25 -
PLANCHE 10 / FIGURE 10
- 26 -
ITEM No. 1 2 3 4
DESIGNATION Brushless motor - DC24V Transfer roller Paper feed roller - MM32 Magnetic clutch -43z
QTY 1 1 1 1
PLANCHE 10 / FIGURE 10
- 27 -
PLANCHE 11 / FIGURE 11
- 28 -
ITEM No. 1 2 3
QTY 1 1 1
PLANCHE 11 / FIGURE 11
- 29 -
1 3
PLANCHE 12 / FIGURE 12
- 30 -
ITEM No. 1 2 3 4
REFERENCE 189245462 189242841 189432292 189245470 Laser unit Micro switch Fan motor
DESIGNATION
QTY 1 1 1 1
PLANCHE 12 / FIGURE 12
-1-
3. PERSONNALISATION
Modle / model : LFF3/LFF4
PLANCHE 1
REPERE 1
DESIGNATION Pupitre marqu Sagem MF5461/ Sagem MF5461 front panel marked Pupitre marqu Sagem MF5461 (CN)/ Sagem MF5461 (CN) front panel marked Pupitre marqu Sagem MF5481/ Sagem MF5481 front panel marked Pupitre marqu Sagem MF5481-N/ Sagem MF5481-N front panel marked Pupitre Sagem MF9016 TG assembl/ Front panel MF9016 TG marked assy
REFERENCE
252366987
252827500
252606972
252610004
252823172 252296680 252629417 186770538 143826202 186770538 186770538 186770538 186770538 186770538 252551974 252551961 251500478 251500501 251500650 251500572 251500564 252490928
LFF3 de base assembl / Basic LFF3 assembly LFF4 de base assembl / Basic LFF4 assembly
Cordon dalimentation secteur / AC adaptor Franais / French Anglais / English Allemand / German Espagnol / Spanish Italien / Italian Nerlandais / Dutch Autriche / Austria Cordon ligne tlphonique / Telephone line cord Franais/French Anglais/English Allemand/German Espagnol/Spanish Italien/Italian Nerlandais/Dutch Autriche/Austria Carte UC programme MF5461 (SAV) / MF5461 main PCB board programmed (SAV) Carte UC programme MF5481-N (SAV) / MF5481N main PCB board programmed (SAV)
10
252629152
TABLE OF CONTENTS
1. DETAILED SECTION DESCRIPTIONS ....................................... 1-1
1.1 COMPONENT LAYOUT ............................................................................1-1 1.1.1 MECHANICAL COMPONENTS........................................................1-1 1.2 PRINTING .................................................................................................1-2 1.2.1 PRINTING PROCESSES AROUND THE DRUM .............................1-2 1.2.2 CHARGE ..........................................................................................1-3 1.2.3 LASER EXPOSURE .........................................................................1-4 Overview...............................................................................................1-4 Block Diagram ......................................................................................1-5 Error Conditions ....................................................................................1-5 1.2.4 DEVELOPMENT...............................................................................1-6 Overview...............................................................................................1-6 Toner End Detection .............................................................................1-8 1.2.5 TRANSFER AND SEPARATION......................................................1-9 Overview...............................................................................................1-9 Cleaning Mode......................................................................................1-9 1.2.6 DRUM CLEANING..........................................................................1-10 1.2.7 PAPER FEED AND REGISTRATION.............................................1-11 Overview.............................................................................................1-11 Paper Feed Drive Mechanism ............................................................1-12 Paper Feed Operation ........................................................................1-13 Registration.........................................................................................1-14 Paper End Detection...........................................................................1-15 Jam Detection .....................................................................................1-16 1.2.8 FUSING ..........................................................................................1-17 Overview.............................................................................................1-17 Power Save Control ............................................................................1-18 1.2.9 COVER SWITCH............................................................................1-19 1.2.10 PAPER FEED DRIVE RELEASE AND FUSING DRIVE RELEASE ......................................................................1-20
2.3.5 THERMISTOR ................................................................................2-10 2.3.6 HOT ROLLER STRIPPERS ...........................................................2-10 2.3.7 THERMOSTAT ...............................................................................2-11 2.4 PAPER FEED..........................................................................................2-12 2.4.1 PAPER FEED ROLLER REMOVAL ...............................................2-12 2.4.2 REGISTRATION ROLLER .............................................................2-13 (ALSO KNOWN AS ROLLER DRIVEN IN THE PARTS CATALOG) 2-13 2.5 OTHERS .................................................................................................2-14 2.5.1 TRANSFER ROLLER .....................................................................2-14 2.5.2 FAN MOTOR ..................................................................................2-15 2.5.3 MAIN MOTOR REMOVAL..............................................................2-16 2.6 PSU (KNOWN AS POWER SUPPLY UNIT IN THE PARTS CATALOG)...................................................................2-17 2.6.1 PSU REMOVAL...............................................................................2-17
ii
COMPONENT LAYOUT
No. A
TECHNICAL DOCUMENT
Toner Cassette
C D E F G H
Upper Tray Bottom Plate Paper Feed Roller Transfer Roller Pressure Roller Hot Roller Paper Exit Roller
Description Consists of the laser diode unit, cylindrical lens, f-theta lens, polygon mirror motor, and other laser optical components. Consists of the OPC drum, toner, toner application roller, development roller, charge brush roller, cleaning blade, and other development components. Presses paper stacked in the upper paper tray against the paper feed roller. Picks up the top sheet of paper from the stack in the upper paper tray and feeds it into the transfer area. Applies a charge to the paper to pull the toner off the drum and onto the copy paper. Applies pressure to the paper during fusing. Fuses the toner to the copy paper. Feeds the paper out of the printer.
1-1
PRINTING
1.2 PRINTING
1.2.1 PRINTING PROCESSES AROUND THE DRUM
[A] [K]
[G] [H]
This machine uses a write to black system, using negative toner. Charge: The charge brush roller [A] gives the OPC drum [B] surface a negative charge. Exposure: A laser [C] writes a latent image on the drum. The charge in the area exposed by the laser beam drops. Development: The development roller [D] carries toner to the drum and develops the latent image on the drum. The following charges are applied. Development bias (during printing): Toner application roller [E] Development roller [D] Switching bias (At the start and the end of any print process): Toner application roller [E] Development roller [D] Image Transfer: The transfer roller [F] pulls the toner from the drum onto the paper [G]. Paper Separation: The antistatic brush [H] removes the charge on the underside of the paper to help the paper separate from the drum. Drum Cleaning: The cleaning blade [J] removes any toner remaining on the drum after the image is transferred to paper. The high voltages [K] are supplied from the Power Supply Unit board.
1-2
PRINTING
1.2.2 CHARGE
[B]
G182D102.WMF
The OPC (Organic Photoconductor) drum [A] used in this machine is small in diameter. This allows a very compact design. A charge roller [B] charges the photoconductor. The charge roller has the advantage of not generating ozone. A large negative voltage is applied from the Power Supply Unit board to the charge roller. This charge roller gives the OPC drum surface a negative charge.
[C]
G182D003.WMF
The voltage to the charge roller is supplied through the terminal [C] from the Power Supply Unit board.
1-3
Detailed Descriptions
[A]
PRINTING
[J]
TECHNICAL DOCUMENT
Laser Unit Layout A : Laser Diode Unit B : Polygon Mirror Motor C : F-theta Lens D : First Mirror E : Second Mirror F : Laser Synchronization Detector G : Cylindrical Lens H : Synchronization Detector Lens J : Shutter
This machine uses a laser diode to produce an electrostatic latent image on the OPC drum. The laser diode unit converts image data into laser pulses, and the optical components direct these pulses to the OPC drum. As a mechanical safety feature, the shutter [J] closes to block the laser beam path whenever the front door is opened.
1-4
PRINTING
Block Diagram
Engine Board
Detailed Descriptions
Regulator
Interlock Switch
G182D012.WMF
TECHNICAL DOCUMENT
The Engine Board controls the laser diode power (APCSH) and transfers data for printing to the laser diode (VIDEO). As an electrical safety feature, there is an interlock switch on the Engine Board. This switch cuts +24 volts whenever the front door is opened.
Error Conditions
Laser Error The machine detects laser synchronization signal pulses (PGSYCI) 70 milliseconds after the (LDENA) signal is sent. It detects a laser error if the pulse count does not reach the specified number within 400 milliseconds. When this occurs, the machine warns the customer on the LCD panel (Error 56). Polygon Mirror Motor Error The machine detects a polygon mirror motor error when the (PMLOK) signal does not go low within 3.5 seconds of the (PMENA) signal. When this occurs, the machine warns the customer on the LCD panel (Error 57).
1-5
PRINTING
1.2.4 DEVELOPMENT
Overview
[C] [D]
[A]
This machine uses mono-component toner, which is composed of resin and ferrite. The toner mixing bar [A] stirs and carries toner to the toner application roller [B]. The toner application roller supplies toner to the development roller [C]. As the development roller turns past the toner metering blade [D], only a thin coating of negatively charged toner particles stays adhered to the development roller. During printing, a bias voltage is applied to the toner application roller and another bias voltage is applied to the development roller. The toner is transferred from the toner application roller to the development roller by the potential difference between these two rollers. The development roller applies toner to the exposed areas of the latent image as they turn past the drum.
[B]
G182D103.WMF
1-6
PRINTING
[A]
[B]
TECHNICAL DOCUMENT
The voltage to the development roller and the toner application roller is supplied through the terminals ([A] for the development roller and [B] for the toner application roller) from the Power Supply Unit board.
1-7
Detailed Descriptions
PRINTING
1-8
PRINTING
[B] [E]
This machine uses a transfer roller [A], which touches the OPC drum [B] surface. A constant current is applied to the transfer roller from the power supply unit board [C]. The positively-biased transfer roller pulls negatively-charged toner off the drum. The curvature of the drum, and the antistatic brush [D], help the paper [E] to drop away from the drum.
[D]
TECHNICAL DOCUMENT
Cleaning Mode
If a paper jam occurs during printing, toner may be transferred to the transfer roller surface. To prevent this toner from transferring to the underside of the paper, the transfer roller must be cleaned before the next printing run. While the machine is in the cleaning mode, the Power Supply Unit board applies a negative voltage to the transfer roller. The negatively charged toner on the transfer roller is then transferred back to the drum. The machine goes through the cleaning mode at the following times. x At power-up: The process starts when the fusing temperature reaches the standby temperature. x When the cover is opened and then closed during the printing process. x After a printer jam has been cleared.
1-9
Detailed Descriptions
PRINTING
The cleaning blade and the used toner tank are contained in the toner cartridge. A counter blade system is used for drum cleaning. The cleaning blade [A] removes any toner remaining on the drum after the image is transferred to the paper. This removed toner is stored in the used toner tank [B]. There is no used toner overflow detection mechanism, because the used toner tank is large enough for the lifetime of the toner cassette.
G182D102.WMF
1-10
PRINTING
Paper Feed System: Paper Lift Mechanism: Sheet feeder Tray Capacity: Paper End Detection: Paper Size Detection:
TECHNICAL DOCUMENT
Feed roller [A] and Friction pad [B] Bottom plate with spring [C] 1 sheet feeder [D] 250 sheets [E] Paper end sensor None
1-11
Detailed Descriptions
PRINTING
[D]
The feed roller [A] is located above the upper tray bottom plate [B], and the friction pad [C]. It allows only one sheet to feed from the paper tray. They are controlled by the paper feed clutch [D]. The registration sensor detects the leading edge of the paper and synchronizes paper feed with the activation of the laser diode to write the image on the OPC drum.
TECHNICAL DOCUMENT
1-12
PRINTING
[F]
[A] [B]
G182D007.WMF
A : Paper feed drive gear B : Paper feed clutch C : Paper feed roller
TECHNICAL DOCUMENT
The paper feed drive gear [A] always rotates while the main motor rotates, since the paper feed clutch (magnet clutch) [B] is energized to turn the paper feed roller [C]. When the paper feed clutch [B] is energized to turn the feed roller, the paper feed roller feeds one sheet of paper from the tray. The paper is fed into the machine by the registration roller.
1-13
Detailed Descriptions
PRINTING
[A]
Registration
The registration sensor [A] detects the leading edge of the paper and synchronizes paper feed with the writing of the image on the drum, so that the image and paper match up properly. This sensor also detects paper feed jams.
TECHNICAL DOCUMENT
1-14
PRINTING
[B]
Detailed Descriptions
[C]
The laser unit [A] has the paper end sensor [B] built into it. The paper end sensor detects the presence or absence of paper. The sensor has an actuator that extends through a slot in the paper tray bottom plate [C], so that the sensor is actuated when paper is placed in the upper tray. When the upper tray runs out of paper, the actuator of the paper end sensor moves into the slot in the upper tray bottom plate. This informs the CPU that paper has run out.
TECHNICAL DOCUMENT
1-15
PRINTING
Jam Detection
Jam 1. Paper jam at the paper cassette When the registration sensor does not turn on within 2.65 seconds after the paper pick-up clutch for the paper cassette turns on. Jam 2. Paper did not pass the registration sensor When the registration sensor does not turn off within the specified time for passing each paper size (see below) + 3 seconds after the registration sensor turns on.
Paper Size Specified Time (msec)
1820
When the paper exit sensor does not turn on within 2.1 seconds after the registration sensor turns on.
TECHNICAL DOCUMENT
Jam 4. Paper jam in the fusing exit area When the paper exit sensor does not turn off within 3.0 seconds after the registration sensor turns off. Jam 5. Paper no feed jam in the bypass tray When the registration sensor does not turn on within 1.6 seconds after the main motor starts.
1-16
PRINTING
1.2.8 FUSING
Overview
After the image is transferred, the copy paper enters the fusing unit. The image is fused to the copy paper by applying heat and pressure through the use of a hot roller [A] and pressure roller [B]. The CPU monitors the hot roller temperature through a thermistor [C] that is in contact with the hot roller surface. A thermostat [D] protects the fusing unit from overheating. The hot roller strippers [E] separate the copy paper from the hot roller and direct it to the exit rollers [F]. The paper feed/exit sensor [G], which is under the fusing unit, monitors the progress of the copy paper through the fusing unit and detects misfeeds. The exit rollers [F] drive the copy paper to the paper output tray. Springs [H] at the front and rear apply the proper fusing pressure between the hot roller and pressure roller. The fusing lamp [K] is located in the hot roller.
TECHNICAL DOCUMENT
1-17
PRINTING
[A] 170C
[t1]
[t2]
TECHNICAL DOCUMENT
t
G182D013.WMF
When the power saver timer expires, the machine automatically goes into energy saver mode. Power saver timer t1 = ? minutes. x After time interval t1 passes following printing, copying, scanning, or keyin [A], the LCD and all LEDs go off. t1 + t2 = ? minutes or ? minutes (selectable) x The default value is ? minutes. (Economy Mode) x Pressing the Clear Modes key for more than one second will change this condition. x When the Economy Mode LED is lit, t1 + t2 = ? minutes. x When the Economy Mode LED is not lit, t1 + t2 = ? minutes.
1-18
PRINTING
G182D014.JPG
x x x x x x
Power pack Laser diode driver Fan motor Main motor Polygon mirror motor Fusing lamp
1-19
Detailed Descriptions
PRINTING
[D]
[A]
The main motor drives the paper feed unit, the transfer roller, the toner cassette, and fusing unit through a series of gears as follows. Main motor [A]
Idle gear 1[B] Hot roller gear [H] Idle gear 4 [I] Exit roller gear [J]
Idle gear 2 [C] OPC drum gear [F] Transfer roller gear [G]
1-20
PRINTING
PAPER CASSETTE
1.2.10 PAPER FEED DRIVE RELEASE AND FUSING DRIVE 2. REPLACEMENT AND ADJUSTMENT RELEASE
The following table shows the part replacement rank, which explains the difficulty of [I] each replacement procedure. [H] Definition: [B] [J] A: Replacement in the field cannot be recommended. (It takes time and needs space.) B: Replacement in the field is recommended. (It should take less than 10 minutes.) [C] C: Replacement in the field is recommended. (It should take less than 5 minutes.) Part unit
Paper cassette Laser
Rank
C C C C C C C B B B B B B A [G] C A G182D009.WMF C A
Fusing
[A]
TECHNICAL DOCUMENT
Idle gear 1[B] Hot roller gear [H] Idle gear 4 [I] Exit roller gear [J]
Idle gear 2 [C] OPC drum gear [F] Transfer roller gear [G]
1-20 2-1
Replacement Adjustment
The main motor drives the paper feed unit, the transfer roller, the toner cassette, and fusing unit through a series of gears as follows.
PAPER CASSETTE
[A]
Side Fence
G182R001.JPG
[C]: Side fence Left Unhook at the rear. [D]: Side fence Right Unhook at the rear. NOTE: Lift the bottom plate before removing the side fences.
G182R003.JPG
[D]
2-2
PAPER CASSETTE
Bottom Plate
[E]: Bottom plate
[G]
Unhook at both sides of the cassette [F]. Detach from the pin [G] at both sides.
[E]
G182R004.JPG
G182R005.JPG
TECHNICAL DOCUMENT
Friction Pad
[H]: Friction pad (two hooks) NOTE: Be careful not to lose the spring [I]. [H]
G182R006.JPG
[I]
2-3
Replacement Adjustment
LASER UNIT
[C]
[B]
[A]: Laser diode unit harness [B]: Polygon mirror motor harness [C]: Laser unit (3 screws [circled in blue above]) NOTE: When re-assembling, make sure to set the positioning pin [D] in the hole [E]. Warning Labels [F] [E] [D]
[F]
[C]
G182R007.JPG
G182R008.JPG
2-4
LASER UNIT
CAUTION VORSICHT
CATION-CLASS 3B LASER RADIATION WHEN OPEN AVOID EXPOSURE TO THE BEAM VORSICHT-LASERSTRAHLUNG KLASSE 3B WENN ABDECKUNG GEOFFNET NICHT DEM STRAHL AUSSETZEN
>PS<
3BLASERCAUTION.WMF
2-5
Replacement Adjustment
FUSING AREA
LASER UNIT
Preparation: >PS< 1) Remove the upper unit. (See Upper Unit Removal.)
3BLASERCAUTION.WMF
[B]
[D]
[C]
[D]
[D]
[A]: Thermistor harness [B]: Paper exit sensor harness [C]: Fusing lamp harness [D]: Fusing unit (4 screws [circled in blue above])
2-5 2-6
Replacement Adjustment
[D]
[A]
FUSING AREA
[A]
G182R010.JPG
[B]: Paper exit assembly (2 screws [circled in blue in the lower diagram])
G182R011.JPG
2-7
Replacement Adjustment
FUSING AREA
Fusing Lamp
[A]: Fusing lamp (2 screws)
G182R013.JPG
G182R015.JPG
NOTE: Do not touch the surface of the fusing lamp with bare hands.
[A]
Reassembly
When reassembling, be careful to set the fusing lamp on the frame first, then set the terminals [B] and [C].
G182R018.JPG
[C]
[B]
G182R017.JPG
G182R016.JPG
2-8
FUSING AREA
Hot Roller
[A]: Electrode (1 screw)
[A]
G182R019.JPG
NOTE: Do not touch the surface of the hot roller with bare hands.
TECHNICAL DOCUMENT
G182R020.JPG
[C] NOTE: When re-assembling, be careful not to damage the hot roller strippers [C].
Replacement Adjustment
2-9
FUSING AREA
TECHNICAL DOCUMENT
G182R048.JPG
[B] NOTE: When re-assembling, be careful to set the bushing [B] and spring [C] in the correct position.
[C]
G182R047.JPG
2-10
FUSING AREA
2.3.5 THERMISTOR
Preparation: x Remove the paper exit assembly (
2.3.2). [A]: Thermistor (1 screw) NOTE: When reassembling, do not damage the thermistor, and check that the element touches the hot roller.
[A]
G182R023.JPG
Preparation: x Remove the paper exit assembly ( 2.3.2). x Remove the fusing lamp and hot roller ( 2.3.3). There are 3 hot roller strippers [A] in the fusing unit. [B]: Hot roller stripper (1 spring [B] each) NOTE: When reassembling, be careful not to lose the spring [B].
G182R022.JPG
[A]
[B]
[A]
G182R021.JPG
2-11
Replacement Adjustment
FUSING AREA
2.3.7 THERMOSTAT
Preparation: x Remove the paper exit assembly (
2.3.2). x Remove the fusing lamp and hot roller (
2.3.3). [A]: Thermostat (2 screws)
G182R024.JPG
TECHNICAL DOCUMENT
G182R025.JPG
2-12
PAPER FEED
G182R026.JPG
TECHNICAL DOCUMENT
[C]: Paper feed roller (2 clips, one at the left side [D], and one at the right side)
G182R030.JPG
[C]
G182R030.JPG
2-13
Replacement Adjustment
[B]
G182R027.JPG
[D]
G182R028.JPG
PAPER FEED
G182R031.JPG
2-14
PAPER FEED
Preparation: 1) Remove the upper unit. (See Upper Unit Removal) 2) Remove the paper tray 3) Remove the toner cartridge [A]: Paper tray guides (2 screws) [B]: Left shield (13 screws & 2 screws at the bottom) [C]: Right shield (9 screws) [D]: Laser shield (4 screws) [E]: Guide shield (4 screws) [B]
[C]
TECHNICAL DOCUMENT
[A]
G182R035.JPG
G182R040.JPG
[G] [F]: Plate (2 screws) [G]: White bushings [H]: Registration roller (lift it out)
[F] [H]
G182R034.JP
2-15
Replacement Adjustment
OTHERS
2.5 OTHERS
2.5.1 TRANSFER ROLLER
Preparation: 1) Remove the upper unit. (See Upper Unit Removal.) 2) Remove the toner cartridge. [A] [A]: Transfer roller [B]: Black bushing [B]
G182R036.JPG
G182R037.JPG
2-16
OTHERS
OTHERS
[C]
G182R038.JPG
TECHNICAL DOCUMENT
[F]
G182R041.JPG
2-18 2-17
Replacement Adjustment
[A]
G182R035.JPG
[F]
[D]
G182R040.JPG
OTHERS
[C]
TECHNICAL DOCUMENT
[A]
G182R035.JPG
[F]
[D]
G182R040.JPG
[F]
G182R041.JPG
2-18
2.6
TECHNICAL DOCUMENT
G182R042.JPG
2-19
Replacement Adjustment